Jet Propulsion Notes

GOODWILL GATE2IIT
JET PROPULSION
Thrust equation for an air breathing engine:
F = ṁa [(1+f) Cj - Ca)] + (Pe - Pa) Ae
Where, f = fuel to air ratio,
Neglecting f,
F = ṁa (Cj - Ca) + (Pe - Pa) Ae
ṁa (Cj- Ca) = momentum thrust
(Pe - Pa) Ae = pressure thrust
ṁa = mass flow rate of air entering the engine
Cj = exit velocity
Ca = inlet velocity
Pe = exit pressure
Pa = ambient pressure
F = thrust
ṁa Cj = gross momentum thrust
ṁa Ca = intake drag
 For maximum thrust, expansion should optimum i.e. Pe =Pa
∴ F = ṁa (Cj- Ca)
Or, F = ṁa [(1 + f) Cj - Ca ]
EFFICIENCIES:
2
HEAT LOSSES UNUTILISED KINETIC ENERGY = ṁ )
HEAT ENGINE OUTPUT THRUST

POWER POWER
POWER
(ṁf x CV ) (Propulsive Power = ) (T.P. = F .Ca)
Propulsive power available to propel aircraft forward is propulsive power and actual power available to propel
aircraft forward is thrust power.
I. Propulsive Efficiency / Froude Efficiency :
It is the ratio of useful energy or thrust power to the sum of that energy and unused kinetic energy of jet
relative to the earth.
ηP =
Contact us: +91 -9933949303 / 7338451418

Write: info@goodwillgate2iit.com
Web: www.goodwillgate2iit.com Page 1
GOODWILL GATE2IIT
=
ṁ
ηP = where =
NOTE:
1. ηP is the measure of effectiveness with which the propelling duct is being used for propelling the
aircraft.
2. The above expression for ηP is valid for all air breathing engines.
3. For maximum thrust, = 0 i.e. ηP = 0.
4. For maximum efficiency, = 1 i.e. F = 0.
5. For maximum thrust power,
Thrust power =
=ṁ
= ṁ
For maximum thrust power, differentiate with respect to and equate to zero.
∴ = =
∴ Cj = 2 Ca
∴ ηP = 66.67 %
II. THERMAL EFFICIENCY:
ṁ
ηT = = ṁ
= where, = and f=
III. OVERALL EFFICIENCY:
ηO =
= propulsive efficiency x thermal efficiency
IV. THRUST SPECIFIC FUEL CONSUMPTION:
Contact us: +91 -9933949303 / 7338451418

GOODWILL GATE2IIT
TSFC =
ṁ
= x 3600
V. THRUST POWER SPECIFIC FUEL CONSUMPTION:
TSFC =
ṁ
= x 3600
VI. SPECIFIC THRUST:
Fs = = = (Cj – Ca)
ṁ
It provides an indication of relative sizes of engines producing same thrust because dimensions of engine are
primarily determined by air flow.
VII. NON-DIMENSIONAL THRUST:
Non-Dim Thrust = =
INTAKE /DIFFUSER EFFICIENCY:
The main function of intake is to minimize the pressure loss upto the compressor phase while ensuring that
the flow enters the compressor with uniform pressure and velocity.
The efficiency of diffuser can be expressed in two ways;
1. Isentropic efficiency:
ηid =
2. RAM efficiency:
ηR =
Contact us: +91 -9933949303 / 7338451418

GOODWILL GATE2IIT
To1 = Toa = To +
1. P01 – Pa is referred as RAM pressure rise.

2. Take diffuser efficiency as 0.93 for subsonic
3. ηid< 0.93 for supersonic
4.
5. For supersonic intakes :
Pressure recovery factor should be as high as possible.
PRF =
If PRF is not given than,
PRF =
PROPELLING NOZZLE:
If , then unchoked
, then choked
Where, Pc = critical pressure
Where, ηin= nozzle efficiency =0.95
1. ηiN =
2. If nozzle is unchoked take for further calculation and we have optimum expansion.
3. If nozzle is unchoked, Cj =
4. If nozzle is choked take for further calculation.
5. Calculate Tc and ρc
6. If nozzle is unchoked, Cj =
7. Consider pressure thrust in calculating total thrust.
Standard values for engine performance calculations:
1. Heating value of fuel – 43100 KJ/kg

2. Cp(air) - 1.005 KJ/kg K
3. (air) - 1.4
4. Cp (gas) - 1.107 KJ/kg K
5. (gas) - 1.33
Contact us: +91 -9933949303 / 7338451418

GOODWILL GATE2IIT
OPTIMISATION OF TURBOJET ENGINE
SUBSONIC CRUISE CONDITION
 Basic thermodynamic parameters for the design of turbojet engine are turbine inlet temperature and
compressor pressure ratio.
 Thrust is strongly dependent on the value of TIT.
 At constant pressure ratio an increase in TIT will cause some increase in SFC .
 The gain in FS with increasing temperature is invariably more important than the penalty in increased
SFC particularly at high flight speeds where small engine size is essential to reduce both weight and
drag .
 The effect of increase in pressure ratio is to reduce SFC.
 At fixed value of T03, increasing the pressure ratio initially results in an increase in Fs but
eventually leads to decrease.
 The optimum pressure ratio for maximum specific thrust increases as value of TIT increases.
FOR HIGHER CRUISE CONDITIONS AT SAME AlTITUDE:
Contact us: +91 -9933949303 / 7338451418

GOODWILL GATE2IIT
 For a given value of pressure ratio and TIT, SFC increases and specific thrust decreases.
 These effects are due to the combination of increase in inlet momentum drag and an increase in
compressor work due to rise in compressor inlet temperature.
 Compressor curves for different altitudes show an increase in F s and on decrease in SFC with
increasing altitude due to fall in temperature and the resultant reduction in compressor work.
 Notable effect of increase in design cruise speed is that the optimum compressor pressure ratio for
maximum specific thrust is reduced.
REQUIREMENT OF SUPERSONIC AIRCRAFT:
The higher the temperature at compressor inlet and need for higher jet velocity make the use of high turbine
inlet temperature desirable and indeed essential for arsenic operation of supersonic aircraft.
VARIATION OF THRUST & SFC WITH FLIGHT CONDITIONS OF TURBOJET ENGINE (PERFORMANCE):
The following curves are obtained for designed point are:
 If the engine was run at fixed rotational speed the compressor pressure ratio (r) and turbine inlet
temperature (T03) would change with intake conditions.
 The above curve shows when turbojet engines are operating at maximum rotational speed.
 Thrust decreases significantly with increase in altitude due to decrease in ambient pressure and
density.
 Specific thrust increases with altitude due to favourable effect of lower intake temperature.
 SFC decreases with increase in altitude
 With increase of Mach number at fixed altitudes, the thrust initially decreases due to increase in
momentum drag and then starts to increase due to beneficial effects of RAM pressure rise.
 At supersonic Mach number this increase in thrust is substantial.
ADVANTAGES OF TURBOJET ENGINE:
 Suitable for long distance flight at higher speeds and altitudes.

 Lower frontal area and shorter landing gears.
 Lower weight per unit thrust at designed speed and altitude.
 Pressure rise through inlet diffuser is significant.
 Reheat can be employed for the increased thrust (After burner).
DISADVANTAGES OF TURBOJET ENGINE:
 Take off run is longer requiring longer runways.

 Specific fuel consumption is comparatively higher at lower speeds and altitude.
 Uneconomical on short at distance flight.
 Lower thrust and propulsive efficiency at lower speeds.
Contact us: +91 -9933949303 / 7338451418

GOODWILL GATE2IIT
TURBOFAN ENGINE
 The turbofan engine is the combination of turboprop and turbojet combining the advantages of both.
 In the turboprop engine a quantity of air flowing through the propeller is much greater than that
passing through the engine, while in turbojet system the entire air passes through the engine.
Working
 Turbofan engine system employs a low pressure ducted fan. The air after passing through the fan is
divided into two streams
1. The primary stream (ṁh) goes through the conventional turbo jet engine consisting of
compressor, combustion chamber, and turbine and exhaust nozzle.
2. The secondary stream (ṁc) at relatively lower pressure is ducted around the turbojet engine
for expansion through the annular fan nozzle.
 Thrust is developed by the bypass air ejecting as cold jet at lower velocities and by primary air ejecting
as a hot gas at much higher velocities.
 Thrust produced by the cold jet at lower velocities reduces the noise levels.
BYPASS RATIO
 It is defined as the ratio of flow through the bypass duct (cold stream) to the flow at entry to the high
pressure compressor (hot stream)
ṁ
β =ṁ
 Thrust assuming both streams are expanded to atmospheric pressure in propelling nozzle.
Net thrust, F =( ṁh Cjh + ṁc Cjc )- ( ṁaCa)
REMARKS
 Turbofan improves propulsive efficiency of engine by reducing mean jet velocity particularly operating
at high subsonic speeds.
 Lower jet velocity also results in less jet noise.
 As compared to turbo jet, turbofan has lower emissions of nitrogen oxides, unburned hydrocarbons,
CO, CO2 etc. because of lower operating temperature in engine cycle.
Contact us: +91 -9933949303 / 7338451418

GOODWILL GATE2IIT
OPTIMISATION OF TURBOFAN ENGINE:
Designer of turbofan engine has to consider these four parameters:
 Overall pressure ratio

 TIT (stator outlet temperature)
 Bypass ratio (β)
 Fan pressure ratio
This graph is for fixed overall pressure ratio and bypass ratio.
 Consider turbofan engine with OPR & BPR fixed.

 For a particular value of TIT the energy input is fixed.
 For low value of FPR the fan thrust will be small and the work extracted.
From low pressure turbine will also be small .Thus, it energy will be extracted from hot stream and large values
of SFC as KE loss in jet is high.
 As, FPR increases fan thrust increases and hot thrust decreases.
 For a given value of TIT, there will be optimum value of FPR for minimum SFC and maximum specific
thrust coincides with minimum SFC.
VARIATION OF SFC WITH SPECIFIC THRUST:
 Increase in BPR improves SFC at the expense of significant reduction in specific thrust.
 The optimum FPR decreases with increasing BPR.
 The optimum SFC requires low specific thrust which is particularly important for high BPR turbofan.
ADVANTAGES OF TURBOFAN:
 Short take off role due to increased thrust at low speed .

 Comparatively quitter engine.
 More efficient flow in fan nozzle.
 On account of short length and low speed .
 Weight / unit thrust is higher than turbojet but lower than turboprop.
 Thrust higher than turbojet at low speed.
DISADVANTAGES OF TURBOFAN:
 Increased frontal area hence more drag.

 Separate thrust reversals are required for hot and cold jets if they are separated.
Contact us: +91 -9933949303 / 7338451418

GOODWILL GATE2IIT
 Specific fuel consumption is higher compared to turboprop.

 Engine is heavier and complicated compared to turbojet.
 Lower speed limit than that of turbojet.
DISADVANTAGES OF TURBOPROP:
 At high speeds due to shocks and flow separation the propeller efficiency decreases rapidly thereby
putting a maximum speed limit on the engine.
 It requires a reduction gear which increases the cost of and also consumes certain amount of energy
developed by turbine.
 Also requires more space and weight increases.
NOTE:
Turboprop generally operates with nozzle unchoked and in a simple straight through tail plane rather than a
convergent nozzle.
THRUST AUGMENTATION
Thrust of a Gas turbine engine can be increased:
 By increasing the mass flow through the engine

 By Increasing the TIT
Requirement for a temporary increase in thrust, example take – off, for accelerations, manoeuvres etc.
Two widely used methods
1. Liquid injection:
 Mixture of water and methanol is used
 Spraying water into compressor inlet causes evaporation of the water droplets, resulting in
extraction of heat from the air, the effect of this is equivalent to a drop in compressor inlet
temperature.
 Reducing the temperature at entry to a turbojet will increase the thrust, due to increase in
pressure ratio and mass flow resulting from the effective increase in rotational speed.
2. Afterburner:
 Stoichometric combustion is desirable for maximum thrust augmentation

 Assuming choked convergent nozzle , T 7 or T5 with or without afterburner , jet velocity
can be found where Tc is given by
or =
 It follows that jet velocity is proportional to at inlet to the propelling nozzle.
Contact us: +91 -9933949303 / 7338451418

GOODWILL GATE2IIT
 The gross momentum thrust, relative to that of the simple turbojet, will be increased in
the ratio
 Afterburner incorporates a variable area nozzle because of the large change in density of
the flow approaching the nozzle resulting from the large change in temperature.
 Variable nozzle is fitted permitting a significant increase in nozzle area. The pressure
thrust will also be increased owing to the enlarged nozzle area.
Ideal RAMJET Engine:
A ramjet engine provides a simple, light propulsion system for high speed flight. Unlike a turbojet engine,
ramjets and scramjets have no moving parts, only an inlet, a combustor that consists of a fuel injector and a
flame holder, and a nozzle.
But, Poa = Poe
So, Mi = Me
‘ Cj =
Now,
Therefore, =
Contact us: +91 -9933949303 / 7338451418


Jet Propulsion Notes

Uploaded by

Copyright:

Available Formats

Jet Propulsion Notes

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Jet Propulsion Notes

Uploaded by

Copyright:

Available Formats

GOODWILL GATE2IIT

F = ṁa [(1+f) Cj - Ca)] + (Pe - Pa) Ae

Where, f = fuel to air ratio,

F = ṁa (Cj - Ca) + (Pe - Pa) Ae

ṁa (Cj- Ca) = momentum thrust

(Pe - Pa) Ae = pressure thrust

ṁa = mass flow rate of air entering the engine

ṁa Cj = gross momentum thrust

 For maximum thrust, expansion should optimum i.e. Pe =Pa

HEAT ENGINE OUTPUT THRUST

I. Propulsive Efficiency / Froude Efficiency :

Contact us: +91 -9933949303 / 7338451418

II. THERMAL EFFICIENCY:

III. OVERALL EFFICIENCY:

= propulsive efficiency x thermal efficiency

IV. THRUST SPECIFIC FUEL CONSUMPTION:

Contact us: +91 -9933949303 / 7338451418

V. THRUST POWER SPECIFIC FUEL CONSUMPTION:

VI. SPECIFIC THRUST:

VII. NON-DIMENSIONAL THRUST:

INTAKE /DIFFUSER EFFICIENCY:

The efficiency of diffuser can be expressed in two ways;

Contact us: +91 -9933949303 / 7338451418

1. P01 – Pa is referred as RAM pressure rise.

Where, Pc = critical pressure

Where, ηin= nozzle efficiency =0.95

Standard values for engine performance calculations:

1. Heating value of fuel – 43100 KJ/kg

Contact us: +91 -9933949303 / 7338451418

OPTIMISATION OF TURBOJET ENGINE

SUBSONIC CRUISE CONDITION

FOR HIGHER CRUISE CONDITIONS AT SAME AlTITUDE:

Contact us: +91 -9933949303 / 7338451418

REQUIREMENT OF SUPERSONIC AIRCRAFT:

The following curves are obtained for designed point are:

ADVANTAGES OF TURBOJET ENGINE:

 Suitable for long distance flight at higher speeds and altitudes.

DISADVANTAGES OF TURBOJET ENGINE:

 Take off run is longer requiring longer runways.

Contact us: +91 -9933949303 / 7338451418

Net thrust, F =( ṁh Cjh + ṁc Cjc )- ( ṁaCa)

Contact us: +91 -9933949303 / 7338451418

OPTIMISATION OF TURBOFAN ENGINE:

Designer of turbofan engine has to consider these four parameters:

 Overall pressure ratio

 Consider turbofan engine with OPR & BPR fixed.

VARIATION OF SFC WITH SPECIFIC THRUST:

 Short take off role due to increased thrust at low speed .

 Increased frontal area hence more drag.

Contact us: +91 -9933949303 / 7338451418

 Specific fuel consumption is higher compared to turboprop.

Thrust of a Gas turbine engine can be increased:

 By increasing the mass flow through the engine

Two widely used methods

 Stoichometric combustion is desirable for maximum thrust augmentation

Contact us: +91 -9933949303 / 7338451418

Ideal RAMJET Engine:

But, Poa = Poe