Bobcat 463

463 SKID-STEER LOADER SPECIFICATIONS
DIMENSIONS
74.5 in.
(1891 mm)
25°
25°
100.5 in.
(2553 mm)
Angle of Departure ............................... 25°

Carry Position ...................................... 8.14" (207 mm)
Dump Angle @ Maximum Height .......... 34°
Dump Height with Standard Bucket ...... 74.5" (1891 mm)
Dump Reach @ Maximum Height ......... 18.5" (470 mm) Turning Radius
Ground Clearance ................................ 5.5" (140 mm) with Standard Bucket ................. 61.3" (1557 mm)
Height to Bucket Hinge Pin .................. 94.5" (2399 mm) A) Width (over tires)
Height with Operator Cab .................... 71.4" (1814 mm) 23 x 5.70-12 .............................. 35.4" (900 mm)
Length without Attachment .................. 75.5" (1918 mm) 23 x 8.50-12 .............................. 43.3" (1100 mm)
Length with Standard Bucket ................ 100.5" (2553 mm) B) Wheel Tread
Operating Height .................................. 123.3" (3132 mm) 23 x 5.70-12 .............................. 29.6" (752 mm)
Rollback @ Carry Position .................... 25° 23 x 8.50-12 .............................. 35.5" (902 mm)
Rollback Fully Raised C) Width (over bucket)
@ Maximum Height ........................... 97° 36" Bucket ................................. 36.0" (914 mm)
Wheelbase .......................................... 28.4" (722 mm) 44" Bucket ................................. 44.5" (1130 mm)
PERFORMANCE
Rated Operating Capacity (SAE J732) ......................................................................................... 700 lbs. (318 kg.)
Tipping Load (SAE J732) .............................................................................................................. 1405 lbs. (637 kg.)
Operating Weight (SAE) ............................................................................................................. 2708 lbs. (1228 kg.)
Travel Speed ............................................................................................................................. 6.5 mph (10,5 km/hr)
Lift Breakout Force (SAE) ............................................................................................................. 1450 lbf. (6450 N)
Tilt Breakout Force (SAE) ............................................................................................................. 2025 lbf. (9008 N)
Axle Torque ........................................................................................................................... 1066 ft.-lbs. (1445 Nm)
Bobcat 463 Skid-Steer Loader Specifications March 4, 2005
ENGINE/ELECTRICAL
Make/Model ........................................... Kubota/D1005-E2B
Fuel/Cooling ........................................... Diesel/Liquid
Horsepower (SAE J1349 Net) ................. 22.5 HP (16,8 kW)
Maximum Governed RPM ...................... 3000 RPM
Torque @ 2200 RPM (SAE Gross) ......... 43 ft.–lbs. (58,3 Nm)
Number of Cylinders ............................... 3
Displacement ......................................... 61.1 cu. in. (1,0 L)
Bore/Stroke ............................................ 2.99 / 2.90 in. (76 / 73,6 mm)
Fuel Consumption .................................. 0.75 gal/hr (2,8 L/hr)
Estimated fuel consumption is based on testing by
Bobcat Company in high duty cycle digging applications.
Lubrication ............................................. Pressure System with Filter
Crankcase Ventilation ............................ Closed breathing
Air Cleaner ............................................. Dry replaceable cartridge with safety element
Ignition ................................................... Compression (Diesel)
Engine Coolant ....................................... Propylene glycol/water mix (53%-47%)
with freeze protection to -34°F (-37°C)
Starting Aid ............................................ Glow plugs
Alternator ............................................... Belt Driven; 65 amps; Open
Battery ................................................... 12 volt; 600 cold cranking amps @ 0°F (-18°C);
115 minute reserve capacity
Starter .................................................... 12 volt; gear reduction type; 3.62 HP (2,7 kW)
HYDRAULIC SYSTEM
Pump Type ............................................... Engine driven, gear type
Pump Capacity ........................................ 10 GPM (37,1 L/min) @ 3000 RPM
System Relief @ Quick Couplers ............. 3000 PSI (207 Bar)
Hydraulic Filter ......................................... Full flow replaceable, 10 micron cartridge filter element in the
hydrostatic pump charge line
Hydraulic Cylinders .................................. Double-acting, with dual cushions on tilt
Control Valve ............................................ 3-Spool, open center with spring detent on lift and detent auxiliary spool.
Fluid Type ................................................ Bobcat Fluid (P/N 6563328)
If fluid is not available, use 10W-30/10W-40 Class SE motor oil
for temperatures above 0°F (-18°C) or 5W-30 Class SE motor oil
for temperatures below 0°F (-18°C).
Bore Diameter
Lift Cylinder (2) .................................. 2.00 in. (50,8 mm)
Tilt Cylinder (1) .................................. 3.00 in. (76,2 mm)
Rod Diameter
Stroke
Hydraulic Function Times
Raise Lift Arms .................................. 3.6 Seconds Bucket Dump ............... 2.3 Seconds
Lower Lift Arms .................................. 2.5 Seconds Bucket Rollback ........... 2.1 Seconds
Bobcat 463 Skid-Steer Loader Specifications March 4, 2005
DRIVE SYSTEM
Main Drive .................. Fully hydrostatic, 4-wheel drive
Transmission ..............Infinitely variable tandem hydrostatic piston pumps,
driving two fully reversing hydrostatic motors
Final Drive Chains Pre-stressed #60 HS endless roller chain (no master link)
and sprockets in sealed chaincase with oil lubrication
(Chains do not require periodic adjustments)
Two chains per side with no idler sprocket
Axle Size ................... 1.5 in. (38,1 mm) heat treated
Wheel Bolts ............... (5) 7/16 in. Wheel bolts fixed to axle hubs
CAPACITIES
Fuel Tank ......................................... 6.5 gals. (24,6 L)
Cooling System .................................. 6.0 qts. (5,7 L)
Engine Oil with Filter ........................... 5.0 qts. (4,7 L)
Hydraulic Reservoir ............................. 5.3 qts. (5,0 L)
Hydraulic/Hydrostatic System ......... 4.0 gals. (15,1 L)
CONTROLS
Vehicle Steering ................... Direction and speed controlled by two hand levers
Loader Hydraulics
Lift & Tilt ........................ Controlled by separate foot pedals
Front Auxiliary (Std.) ...... Controlled by lateral movement of Right Hand (RH) steering lever
Auxiliary Pressure Release .. Lateral movement of RH steering lever after engine has been shut off.
Engine ................................. Hand lever throttle: key-type starter switch and shutdown
Starting Aid .......................... Glow Plugs – activated by Rocker Switch on dash panel
Service Brake ....................... Two independent hydrostatic systems controlled by two hand-operated steering levers
Secondary Brake ................. One of the hydrostatic transmissions
Parking Brake ...................... Finger-operated toggle switch on left-hand instrument panel.

Bobcat 463

Uploaded by

Copyright:

Available Formats

Bobcat 463

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Bobcat 463

Uploaded by

Copyright:

Available Formats

463 SKID-STEER LOADER SPECIFICATIONS

Angle of Departure ............................... 25°

You might also like