P1 P2 P3(303MHz)

27MHz Door knob Alarm

Home

This is a very large article on 27MHz transmitters and receivers.

3 kits are available:
- 27MHz Field Strength Meter - to test your 27MHz transmitter
- 27MHz Transmitter - 2 Channel - transmits two different tones on a 27MHz carrier
- 27MHz Receiver - 2 Channel - receives and decodes 2 different tones
and we have 303MHz and 315MHz links. email Colin Mitchell for details.

Where do you start?

Read all this this article then build the 27MHz Field Strength Meter kit: $6.50 plus $4.00 post
and 27MHz Transmitter - 2 Channel. kit: $6.50 plus $4.00 post
then 27MHz Receiver - 2 Channel. kit $10.50 plus $4.00 post

27MHz Field Strength Meter

Tests 27MHz transmitters
$6.50 plus $4.00 post

Buy: 27MHz FSM kit

27MHz Transmitter - 2Ch
$6.50 plus $4.00 post

Learn about making a 27MHz

transmitter and create a 2-
Channel link to turn on motors and
globes etc.

Buy: 27MHz Transmitter

27MHz Receiver - 2Ch

$10.50 plus $4.00 post

This receiver is used with the 2-

Channel transmitter above to
produce a link to turn on globes
and motors.

Buy: 27MHz Receiver

 What will I learn?
You will learn about designing 27MHz stages - transmitters and receivers
You will learn about 0SCILLATORS - low frequency and 27MHz
You will learn about TUNED CIRCUITS - how they produce an enormous
waveform when operating at a special frequency.

CONTENTS
27MHz transmitter with crystal - 1-transistor with crystal
Receiver for transmitter

27 MHz transmitter without Xtal - Very simple 2-transistor circuit - produces tone.
Receiver for Transmitter

27 MHz transmitter without Xtal - with multivibrator to produce tone.

27 MHz transmitter without Xtal - with multivibrator to produce tone - improved circuit
Receiver for transmitter

2 Channel 27MHz transmitter without Xtal

Receiver for 2 Channel transmitter

4 Channel 27MHz transmitter with crystal

4 Channel 29MHz Transmitter with Xtal

4 Channel Receiver

Field Strength Meters

In this discussion we cover 27MHz transmitters and receivers as found in remote control cars,
aeroplanes, walkie talkies and some of the older-style garage door openers.
We have provided a number of circuits so you can work out the best type for your application and
these circuits will also help you understand which components are critical and which components
can be changed.
It's a matter of looking at each circuit and seeing the general layout, and comparing it to the other
circuits. In this way you are building up a concept of "building blocks" and this is the basis to
learning electronics.
Talking Electronics does not provide any kits for these circuits as the products (toy cars, wireless
doorbells etc) are readily available in toy shops, hobby shops and many of the $2.00 "junk Shops."
You cannot buy many of the special components and the cost of the completed item is less than
buying the components!

WHERE DO YOU START?

Surprisingly, the place to start is to build a piece of test equipment called a Field Strength Meter.
We will describe 3 different Field Strength Meter circuits. The simplest circuit detects RF from the
antenna of a transmitter and provides a reading on a multimeter.
The other two circuits have a tuned front end and as the capacitor is adjusted, the meter increases
to a peak then drops as the frequency is passed.
For experimental purposes, it is not necessary to be on the 27MHz band, but it is handy to know if
your transmitter is producing an output.
You need a starting point and you either need a Field Strength Meter or Radio Controller car or
Walkie Talkie.
You need something to make sure your transmitter is transmitting. It's a Field Strength Meter.

MAKING A TRANSMITTER
This discussion covers a number of transmitters and receivers. The different circuits show you what
is absolutely needed and how different engineers think. Some circuits will work better than others
and some have unnecessary components.
Then you will need a receiver.
Some circuits are 1-channel, some are 2-channel and some are 4-channel. Choose the tone that
suits your requirement.
First we will go over some background.

Let's start:

6 bands (or frequencies) were allocated for the 27MHz band,

Channel Frequency
1 26.995
2 27.045
3 27.095
4 27.145
5 27.195
6 27.255

and these were very popular for transmission - especially in countries where transmitting was
strictly controlled.
Both 27MHz and 49MHz circuitry produced very low cost devices and they are still available. But
you must be careful as some of the latest types are much more sophisticated (and sometimes cost
less than the older types).
We will investigate how they work and how they can be modified.
Very little is available on how these circuits work and this article will cover the "building blocks."
When we use the term "building block" we mean a group of components making up a circuit that
carries out a particular function and can be connected to another circuit to achieve a final result. In
this way you can create your own project without having to design each of the sections. A typical
example is the 5-channel remote control circuit we have modified to produce an on-off action from
two of the outputs. You can build these circuits from scratch, but why re-invent the wheel? If you
want a 27MHz or 49MHzlink, the best idea is to buy a toy and modify it.
If you want voice communication, get a walkie talkie. If you want a single on-off operation, get a
remote control car.
Some remote control cars have up to 5 channels and sell for less than $20.00. You can get
everything you need on 2 printed circuit boards, ready for modification, without having to source the
components.
Look for 4 function models that require 3v operation for both remote and receiver. The fifth function
is "turbo" and is not used in some of the designs. The photo below is the 4(5) function 27MHz
remote control car we discussed above:
 5 channel remote control car as discussed
in the text. It uses only 4 of the 5 channels.

The first two circuits (figs 1& 2) form a single-channel transmitter-receiver link. The second receiver
(fig 7) uses a split supply to power a motor in the forward and reverse direction (it uses the same
transmitter as shown in fig 1). The third transmitter & receiver, (figs 12 & 22) is a multi-channel
design, with a chip in the receiver. Then we cover a 27MHz walkie talkie. This is a 4 transistor
model. It uses the same type of super-regenerative front-end as our receiver circuits and injects
Amplitude Modulated (AM) audio onto the signal. The result is a very noisy transmission but a very
effective way to achieve both transmission and reception with the minimum of components. Most of
the parts have a dual function, operating in both transmit and receive mode. This makes the circuit
very efficient, component-wise.

Before we start, some of the Japanese transistors have either a very high frequency capability or a
very high collector current. These transistors need to have an equivalent for the circuit to work
successfully. Here is a list of some of the type you will come across and some equivalents:

Type: Gain: Vbe Vce Current Case

140 to
2SC3279 NPN 600 0.75v 10v 2amp
@0.5A

BC327 60 45v
PNP 0.7v 800mA
BC328 @300mA 25v
BC337 60 45v
NPN 0.7v 800mA
BC338 @300mA 25v
BC547 45v
BC548 NPN 70 0.7v 30v 100mA
@100mA
BC549 30v
BC557 PNP 100mA
C945 NPN 50v 150mA
1815 NPN 50v 150mA

8050 NPN 10v 1.5A

 8550 PNP 10v 1.5A
9012 PNP 500mA
9013 NPN 500mA
9014 NPN 100mA
9015 PNP 100mA
9018 NPN 700MHz 100mA

27MHz TRANSMITTER with Crystal

Fig 1 shows a simple 27MHz transmitter producing a carrier.

(receiver for this circuit HERE)

The 27MHz transmitter PC board
 Here is the circuit made by Lucian Papadopol iz6nnh@gmail.com
He has created capacitor values by paralleling two values.

This means it produces an unmodulated 27MHz signal and when picked up by a receiver, such as
shown in fig 2, the result is a clean, noise-free reception. To increase the output of the transmitter,
the 390R resistor is replaced by a 220R. This increases the current from 7mA to 12mA. The resistor
could be decreased to 150R for more output. Page 2 of this article covers test equipment that can
be used to detect the output and the frequency of transmission.

MAKING A 5-CHANNEL
TRANSMITTER/RECEIVER
This 5-Channel 27MHz link has 5 outputs. The output goes HIGH when the corresponding button on the
transmitter is pressed. You can use 2,3 4 or 5 of the channels. We chose 5-Channels as it uses the same number of
components as a 2, 3 or 4 channel design.

We will cover the design in detail:

1. The Transmitter 2-Ttransistor, 5-tone (200Hz / 1kHz) transmitter
2. The Receiver "front-end"
3. The receiver

But first:
THE FIELD STRENGTH METER
Before building the Transmitter/Receiver you need to build a Field Strength Meter so you can test the
transmitter.
Here is the circuit for Field Strength Meter MkV. It can be constructed on a small piece of matrix board
or simply soldered together and connected to a 0-500uA movement. A "Movement" is similar to a "Panel
Meter." You can use 0-1mA movement or the 0.5mA current-range on an analogue multimeter.
This is simply an "untuned" RF detector to prove the transmitter is producing a signal.

Field Strength Meter MkV

The Field Strength Meter circuit is simple but it is designed to detect the 27MHz transmitter in this
project. The "lead" is flex or enamelled wire 10cm long and wrapped around the antenna of the
transmitter for 2cm to get RFenergy-transfer. Our prototype transmitter produced about 25% scale
deflection.
1. THE TRANSMITTER
The transmitter consists of two transistors. The first transistor produces the tone in conjunction with the
second transistor and the second transistor produces the 27MHz signal. Button "A" produces a 200Hz
tone button "B" produces 1kHz tone, button "C" produces 1kHz tone button "d" produces 1kHz
tone button "E" produces 1kHz tone

5-tone 200Hz to 3kHz transmitter

The second transistor is a self-contained oscillator and it gets its feedback (to oscillate at 27MHz) from
the transformer. The main coil is the 9t section and the feedback to the base is 4 turns.
Nothing happens until one of the buttons is pressed as the first transistor is held in a "turned-off" state
by the 3M3 and the second transistor is not turned on as the base and 2k2 are not connected to
anything.
When a button is pressed, the 4n7 starts to charge via the resistor connected to the button and the first
transistor starts to turn on.
The 4n7 gets charged to a voltage that allow the first transistor to turn on slightly. This allows current
and voltage to flow through the 2k2 to turn on the second transistor and produce 27MHz. A voltage-
drop is produced across the 100R load resistor and this pushes the left-side of the 4n7 DOWN. The
right side moves down and it feeds some of its energy into the base of the first transistor to turn it on
MORE.
This causes the second transistor to turn on more and create a higher amplitude. After a very short
period of time the energy from the 4n7 (only a small amount of energy is delivered and the amount can
be worked out by knowing how many millivolts gets generated across the 100R between normal
operation of the second transistor and its higher turned-on state) has been fully delivered and and the
first transistor starts to turn off. This causes the second transistor to turn off slightly and the 4n7 "rises in
the circuit." At the same time it gets charged again by the resistor connected to the switch and the cycle
repeats.
The end result is a fairly brief pulse that causes the second transistor to create a larger amplitude. This
is detected by a receiving circuit as a higher amplitude 27MHz signal produced 200 times or 1,000 times
per second. This is called an AMPLITUDE MODULATED SIGNAL and in this case it shown on a CRO
as peaks or spikes and in a speaker as a buzz or tone.
The frequency of the tone is determined by the value of the 4n7 and the resistor that charges it.
2. THE RECEIVER FRONT END
The front end of a 27MHz receiver is slightly different to the front end of a 27MHz Walkie Talkie. The
circuit is very lightly loaded so that it will detect the slightest signal and this makes it very sensitive.
The component that does this is the 3k9 in the power rail.
The transistor has only about 2v across it and takes less than 1mA.
The circuit is a common-base amplifier and under certain circumstances, a single transistor in this
configuration will oscillate.
 The receiver "front-end" put together for experimenting

First, let's describe how a common-base stage works.

The 220k base-bias resistor turns the stage on. The coil in the collector is the load but since it is such a
low resistance, a voltage-dropping resistor has to be placed in the emitter. This resistor only limits the
current through the circuit.
It is by-passed with a 3n3 capacitor and does not cone into the operation of the operation of the circuit.
There are two ways to turn on a transistor.
one is to hold the emitter fixed and deliver a voltage and current to the base. The other is to hold the
base rigid and reduce the voltage on the emitter.
that is what we have done in this circuit.
The 4u7 electrolytic on the base holds it rigid and the 39p reduces the voltage on the emitter to turn the
transistor ON and during the other part of the 27MHz cycle, it increases the voltage on the emitter to
turn it OFF.
This concept must be understood before we can advance further.
The circuit starts by receiving a pulse of current through the 6t coil and 47p capacitor, when it is turned
on. These two components form a TUNED CIRCUIT and when they receive energy, they produce a
sine-wave (sinusoidal) waveform that appears on the lower part of the tank circuit and this is passed to
the emitter via the 39p. It's an amazing fact that two simple components can produce a sinewave that
has an amplitude larger than the voltage applied to the pair, but this is what happens and to fully explain
it, would require another chapter.
However the end result is the emitter is pushed down to turn the transistor ON more and pulled up to
turn it off. The 70t inductor on the emitter simply keeps it away from the 0v rail so that the pulses on the
39p can have an effect on pushing and pulling the emitter.
To explain how the inductor works is very difficult, however it has the effect of allowing the 39p to push
the voltage lower on the emitter, than if it were not included. If the inductor is removed, the 39p will have
a very hard job to push against the 3n3. But if the 3n3 is removed the 39p will have little difficulty
pushing against the effect of the 680R.
However when the inductor is added, the 39p has a much easier job of pushing and pulling the emitter.
Even though this is the front end of a receiver, it is actually oscillating at 27MHz.
The circuit has been built for experiential purposes to make sure the 70t inductor and 6t coil work
perfectly to price a sensitive front-end. Never put a circuit on the web without building and testing it with
actual components. Simulation programs cannot predict the outcome of hand-made components.
The 70t inductor is about 7uH and is wound on a 1M resistor with very fine wire. The resistor can be any
high value and does not play a part in the functioning of the circuit. It is just a convenient core for the
winding. The carbon content of the resistor does not have any effect on the inductance.

3. THE RECEIVER
HOW THE RECEIVER WORKS
The receiver is a super-regenerative design and the output is very noisy. However when a signal of the
same frequency as the super-regenerative circuit surrounds the antenna, the circuit has difficulty
radiating a signal and it takes more current and less current. These variations appear across the 3k9
load resistor as a change in voltage (a waveform) and the signal is picked off via a 100n capacitor and
passed to a filter stage that removes most of the background noise and amplifies the signal (tone).
The following diagram shows just some of the stages needed to decode 5 different tones and deliver the
signal to 5 separate outputs:

Block diagram of the 5-Channel Receiver

It would require a minimum of 20 transistors to carry out this requirement and all this has been done in a
single 8-pin chip by the author, as shown in the following circuit:
 5 CHANNEL RECEIVER using H-bridge transistors
The 5 CHANNEL RECEIVER uses a TE5CHRx chip from Talking Electronics. Click HERE to buy the
chip.

Outputs are normally NOT HIGH or LOW but HIGH IMPEDANCE when not activated and this effectively
makes them "out of circuit" as far as the other components are concerned.
Outputs A and B produce FORWARD and REVERSE.
When button "A" on the transmitter is pressed, output A goes HIGH and B goes LOW.
When button "B" on the transmitter is pressed, output A goes LOW and B goes HIGH.
Outputs C and D produce LEFT and RIGHT via an actuator (or a motor).
When button "C" on the transmitter is pressed, output C goes HIGH and D goes LOW.
When button "D" on the transmitter is pressed, output C goes LOW and D goes HIGH.
When button "E" on the transmitter is pressed, output E goes HIGH.

The outputs from the chip drive an "H-Bridge" and each transistor is actually an EMITTER-FOLLOWER.
This means the bridge cannot be connected to a supply higher than the driving circuit.
The voltage drops across the driving components is nearly 2v. This means the motor will see a
maximum of 4v and that's why a 3v motor has been suggested.
The chip delivers about 25mA max into the base of each transistor and depending on the gain of the
transistor, it will supply about 500mA max.
Output 5 is limited to 25mA.

The H-Bridge section can be designed with an L2930, to take the place of 8 H-bridge driver
transistors. The chip has built-in diodes and will deliver up to 600mA per output.

5 CHANNEL RECEIVER using L293D driver IC

 (transmitter for this circuit HERE)

In the circuit above, when the transmitter is off, the car moves forward. When the transmitter is on,
the car reverses and moves in a circular pattern due to the fact that the front wheels steer straight
when the car is moving forward but turn left when the car moves backward. This allows the operator
to guide the car around obstacles. It's a very awkward way to control a car and although it is very
simple and clever, it is not really successful in practice. We will not be going into the mechanics of
how the car steers, only the fact that the transmitter causes the motor to reverse direction. In place
of the motor you could use a relay or two separate motors to carry out a number of functions and
we will show how the circuit can be modified to do this.
The receiver works on a "tone," "no-tone" principle but the transmitter doesn't actually send a tone
as this would require additional circuitry. What happens is the receiver picks up random noise from
the airwaves when the transmitter is not operating and this functions as the tone part of the
reception. This random noise is amplified by the second transistor and passed to a 0.47u
electrolytic that keeps the third transistor in conduction for the majority of the time. The operation of
this will be discussed later. The 10u on the output of the third transistor keeps the output low for the
short periods when the third transistor is not low. The motor is connected in a bridge formation via
four transistors and these change the polarity of the supply to the motor.
When the transmitter is operating, and the receiver is within range, it picks up a 27MHz carrier that
over-rides the random noise and produces a CARRIER. This means the second transistor will not
see any noise and thus the 0.47u electrolytic will charge and turn off the third transistor. The 10u
will charge via the 2k2 and the input to the bridge will change from a LOW to 0 HIGH. This will turn
on the opposite half of the bridge to supply current to the motor in the reverse direction.
Now we will cover the circuit in detail.

HOW THE TRANSMITTER WORKS

The transmitter is a very simple crystal oscillator. The heart of the circuit is the tuned circuit
consisting of the primary of the transformer and a 10p capacitor. These two components oscillate
when a voltage is applied to them. The frequency is adjusted by a ferrite slug in the centre of the
coil until it is exactly the same as the crystal. The crystal will then maintain the frequency over a
wide range of temperature and supply voltage fluctuations. The transistor is configured as a
common emitter amplifier. It has a resistor on the emitter for biasing purposes but the 82p across
the 390R effectively takes the emitter to the negative rail as far as the signal is concerned. The
390R resistor prevents a high current passing through the transistor as the resistance of the
transformer is very low. The tuned circuit operates at exactly the third harmonic (also called the third
overtone - an overtone is a multiple of a fundamental frequency) of the crystal so that the crystal will
oscillate at its third overtone (27MHz) and in-turn, keep the frequency of the circuit stable. The
transformer in the collector of the transistor performs two functions. 1. It matches the impedance of
the transistor to the impedance of the antenna, and 2. Creates a resonant circuit at 27MHz to make
sure the crystal oscillates at this frequency. You can see the transformer creates a resonant circuit
by the fact that it has a capacitor across the primary winding. These two components create a
"resonant" or "tuned " circuit and this is where the circuit "gets its frequency."
The crystal has a fundamental of about 9MHz and it will oscillate at this frequency unless assisted
to oscillate at a higher frequency. This is done by the tuned circuit oscillating at 27MHz.
Now we will look at the impedance-matching feature of the transformer.
The impedance of the output of the transistor is about 1k to 5k and this means it is the impedance
(resistance) "it works at." In other words, it is the characteristic impedance of the transistor in this
type of stage. The impedance of a whip antenna is about 50 ohms and the transformer matches
these two by having a TURNS RATIO.
The primary has about 12 turns and the secondary about 3 turns. This provides part of the matching
requirement. The `pi' network, made up of the 150p, 15 turn air-cored coil and 100p capacitor
assists further in matching the output of the transformer to the antenna. When the power is applied,
the transistor turns on fairly hard due to the 82p in the emitter being uncharged.
This puts a pulse of energy through the 10p and as the transistor turns off slightly due to the 82p
charging, the energy in the 10p capacitor is passed to the primary of the transformer to start the
27MHz cycle. The action of the emitter rising and falling during start-up, allows the base to rise and
fall and this puts a pulse on the crystal to start it oscillating.
The frequency of oscillation OF THE CIRCUIT is generated by the tuned circuit in the primary of the
transformer and the crystal merely keeps the circuit operating at exactly 27.145MHz (or 27.240MHz,
depending on the frequency of the crystal). The turns ratio of the transformer converts a high
voltage waveform (that has little current) from the transistor, into a low voltage waveform with a
higher current.
This is exactly what the antenna requires. But before the signal passes into the antenna it goes
through the pi network, then an 8 turn Radio Frequency Choke. This is 8 turns of enamelled wire
wound on a ferrite core and is called a base-load for the antenna.
The result is a 27MHz frequency called a CARRIER. The carrier produces a clean spot on the band
that is free from background noise.
The 22n across the first stage is designed to remove the high-frequency component from the
waveform. If this were not present, the circuit would never change state. The receiver is tuned to the
frequency of the crystal in the transmitter via a slug-tuned coil in the collector.
When the transmitter is off, the receiver picks up background noise and amplifies it to produce
random-noise. This is amplified by the second transistor and passed to the third via a 0.47u
electrolytic. This electrolytic is designed to keep the third transistor ON for the major part of the time
and it does this in a very clever way. We will assume the supply has just been turned on and the
second transistor is not receiving a signal. The 0.47u will be uncharged and it will charge via the
10k collector resistor and the base-emitter junction of the third transistor.
The action of the current flowing through the base of the third transistor will turn it ON but after a
short time the electrolytic will be fully charged and the current will cease and the transistor will turn
off. A 10u on the collector of the third transistor will then begin to charge via the 2k2 resistor and
after a period of time called the DELAY TIME, the output will be HIGH and change the state of the
bridge. But if a signal is present on the collector of the second transistor, (in our case this will be
background hash), the voltage on the collector will be rising and falling. When the voltage goes low,
it takes the positive end of the 0.47u low and the other end must follow.
The voltage on the negative end will go below the negative rail and at -0.7v it gets clamped by the
diode. This means the electrolytic gets discharged very rapidly when the second transistor turns on.
The result is the electrolytic takes a long time to charge and a short time to discharge, even when
random noise (hash) is being processed.
The action of the 0.47u is amazing and will be explained in more detail in a moment. During the
short periods of time when the third transistor is not turned on, the 10u on the collector will take over
and hold the signal low. It's only when a long duration of silence is encountered, that the circuit will
change state. This period of silence is when the transmitter turns ON and the time is very short in
real terms.
Transistor Q3 is called the switching transistor. It changes between HIGH and LOW to create the
forward and reverse direction. The switching transistor feeds two driver transistors, Q4 and Q9.
Each of these drives two output transistors. Q4 drives Q6 and Q7. Q9 drives Q5 and Q8.
Follow these transistors on the circuit and you will see how the supply is directed to the motor, firstly
in one direction and then the other.
The printed circuit board is quite complex because of the number of driver transistors. But since
these cost less than 2 cents when bought in the million, it is not cheaper to use a chip.

HOW THE 0.47u WORKS

The 0.47u electrolytic on the base of the third transistor needs explaining as its operation is very
clever.

Charging the 0.47u electrolytic

is represented as a battery.

The electrolytic is simply a tiny re-chargeable battery and when the circuit first turns on, it is
uncharged. The charging current passes through the base-emitter junction of the third transistor
and keeps it ON as shown in fig: 3. If the electrolytic is allowed to fully charge, the current will fall to
zero and the third transistor will turn off. But the second transistor discharges the electrolytic quickly
before it has time to fully charge. It does this by turning ON. How the electrolytic discharges is
shown in fig: 4. The only components involved in the discharge are Q2 and the diode. Transistor Q2
is turned on and it will have zero volts (0.3v) on the collector.
 Discharging the 0.47u electrolytic.

This means the positive lead of the electrolytic (equivalent to the positive terminal of the battery) will
drop from say nearly 3v, to 0.3v. The negative lead must follow and normally it would be at -2.7v.
Yes, the negative lead would have a negative voltage on it relative to the 0v rail, if the diode was
not present. BUT the diode on the negative lead gets turned on as soon as the voltage on the
negative lead falls to -0.7v and prevents it going below -0.7v. As the positive lead falls, the energy
in the electrolytic is quickly discharged through the diode and when the second transistor turns
OFF, the electrolytic is ready for charging, through the 10k resistor.

LOW RAIL VOLTAGE

One of the problems of a low rail voltage is the voltage lost across each of the output transistors.
Each drops about 0.5v across the collector-emitter junction and this leaves only about 2v for the
motor. However the supply voltage must not be increased above 3v as there is a very short period
of time when the circuit is changing from LOW to HIGH and both halves of the bridge are ON. This
is at the mid-point of the change-over and if you work out the various voltage drops across the
base-emitter junctions, it leaves about 0.2v for the two 1k resistors. With a 3v supply, the base
current is limited to 0.1mA by the inclusion of the two 1k resistors and 10mA for the collector-emitter
current. But if the voltage is increased above 3v, the current will increase dramatically and the
transistors will be damaged.

CONNECTING A RELAY
Fig: 5 shows how a relay can be connected to the driver transistor to operate when the transmitter
is switched on. The change-over contacts on the relay can be used to power any device when the
transmitter is off or when it is on.
 Connecting a relay to the driver
transistor. The supply for the relay
can be 6v - 12v.

CONNECTING TWO MOTORS

Fig: 6. shows how to connect two separate motors to the circuit. The motors can be connected to
any voltage from 3v to 12v and the direction of rotation will depend on which way around they are
connected, but transistors Q4and Q7 should be kept at 3v - especially Q9, as it cannot be taken to
a voltage higher than 3v, due to the way it is connected in the circuit.

Connecting two motors to the outputs.

A SPLIT-SUPPLY RECEIVER
The second receiver circuit we will study uses more components to do exactly the same job but it
may have better sensitivity due to the inclusion of one extra stage of amplification and the use of a
higher rail voltage. The higher rail voltage gives some stages a higher gain due to the higher
amplitude of the signal. But some of the gain has been lost in the diode pump as this type of pump
requires more energy to charge the 10u than a 0.47u. The use of a center-tapped voltage source
saves two transistors in the bridge network but necessitates the use of a double-pole switch to
disconnect both halves of the supply.

A 27MHz receiver using a split supply

 The 27MHz receiver PC board

HOW THE SPLIT-SUPPLY RECEIVER WORKS

The operation of the front end of the split-supply receiver in fig: 7 is identical to the receiver shown
in fig: 2. The use of a PNP transistor for Q1has simply turned the circuit up-side-down however the
antenna is still connected to the collector and the parallel tuned circuit is also on the collector.
The circuit is turned on by the 33k on the base and the 47n keeps it rigid and turns the stage into a
common base configuration. The parallel resonant circuit made up of the 8-turn inductor and 15p,
starts the circuit oscillating and the 39p between collector and emitter provides feedback for the
transistor to supply pulses of energy to the tuned circuit to keep it oscillating.
The 220R and 39p are the emitter biasing components, as well as the 390R, 10n and 47n. The
100R and 47u are stage-separating components to remove low-frequency noise from the power
rails and the 22n across the first stage tightens up the power rails as far as the high frequency is
concerned and allows the low-frequency component to appear across the 3k3. The signal across
this resistor is picked off via the 10k/39n combination and passed to two stages of amplification.
The 10k and 4n7 form a filter to remove high frequency pulses. A high frequency pulse will try to
charge the 4n7 and most of the amplitude of the pulse will be lost (attenuated) in the 10k resistor.
Exactly how this works is as follows: The high-frequency pulse will rise and fall before the 4n7 has
time to charge. But a low-frequency will charge the 4n7 and enter the 39n for amplification by the
rest of the circuit. Going back to the first stage, we have already mentioned that it is oscillating at
27MHz and the MOST ACTIVE lead of the circuit is the collector and this is where the antenna is
connected. The waveform produced by the circuit is passed to the antenna and radiated to the
surroundings.
Any other signals of the same frequency will interfere with the circuit's ability to radiate energy and
this is reflected down the antenna to the first stage. The result is it takes slightly more and less
current according to the intelligence on the signal. The word intelligence means the information that
has been added to the carrier.
For a transmitted signal this means voice or music etc. When no transmitted signal is present this is
background hash or "noise." The changes in current will see a waveform develop across the 3k3
feed resistor. The 10k will detect this and pass it to Q2 for amplification. Q2 and Q3 amplify the low
frequency (audio) or "hash" component.
Any high frequency signals will be removed by the 270p capacitors. They act as negative feedback
devices and operates as follows: A rising signal on the base of the transistor turns it ON and the
collector voltage falls. The fall in voltage is passed through the 270p (because it does not have time
to charge) to the base where it counteracts the original signal.
The capacitor ONLY has an effect on high frequency signals and the low frequency signals are
amplified without attenuation. A low-frequency signal will charge the 270p and get lost in the 270p.
After two stages of amplification, the signal appears at a diode pump made up of a 15n capacitor,
two diodes and a 10u electrolytic.
The charging of the 10u takes quite a number of cycles as the 15n is like a teaspoon filling a glass
with water. When Q3 turns off, the 15n is charged via the 4k7, D2 and the 10u. The 15n doesn't
take very long to charge and the current flowing through it puts a tiny amount of charge into the
10u. Transistor Q3 turns on and discharges the 15n through diode D1 in exactly the same manner
as explained previously. When Q3 turns off, the 15n is ready to charge up again. This keeps
happening for hundreds of cycles, each time the voltage on the 10u gets slightly higher.
At a voltage of 0.65v, the base of Q4 begins to turn on. Below this value the base does not see
anything, and does not have any loading effect on the electrolytic. But at exactly 0.65v a tiny
amount of current begins to flow into the transistor to turn it on. The electrolytic keeps charging and
as the voltage rises to 0.66v, 0.67v, 0.68v, 0.69v, the transistor turns on more and more. At 0.7v,
the transistor is fully turned on and any voltage over this simply spills into the base and is passed to
the negative rail via the base-emitter junction. This means the voltage on the 10u does not rise
above 0.7v.
To keep the transistor turned on requires a small amount of current into the base and the
electrolytic supplies this current. In doing so, the energy in the electrolytic gets used up and the
voltage across it reduces.
As the voltage falls, the transistor gets turned off. When the voltage drops below 0.65v, the
transistor is fully turned off and does not see any voltage below this. This means the operating
voltage for the electrolytic is between 0.7v and 0.65v. Q4 feeds Q5 and when Q4 is turned on, the
voltage on the base of Q5 is below 0.65v and it is turned off. The 10u on the collector of Q5 charges
via the 1k5 and when it is above 3.7v, driver transistor Q6 turns on and output transistor Q8
operates the motor.
There are two outputs. One drives the motor in the forward direction and the other drives it in
reverse.

THE TRANSISTORS IN THE FORWARD DIRECTION

There are two transistors for the motor in the clockwise (forward) direction, as shown in fig: 8.
You will notice the turn-on resistor(s) on the base of the driver transistor is lower than for the
reverse direction and this will allow a greater current to be delivered to the motor to give it full speed
in the forward direction.

THE TRANSISTORS IN THE REVERSE DIRECTION

There are 3 transistors driving the motor in the reverse direction, as shown in fig: 9.

These are the switching transistor Q5, the driver transistor Q7, and the output transistor Q9. The
reason why a driver and output transistor are need is to provide a high current for the motor as it
needs a high current at start-up or when under load. A motor may take only 50-150mA when not
loaded but the current will rise to 300-500mA when loaded. It the motor does not receive this high
current, it will appear the car has no power. For the output transistor to deliver this high current, the
base must receive a current according to the gain of the transistor.
The gain of a transistor varies enormously, depending on the current flowing through the collector-
emitter circuit. The DC gain of a transistor is generally specified as between 100 - 450, but this is
under ideal conditions and is determined at a collector current of about 1mA! When the current is
increased, the ability of the transistor to amplify decreases. For a small signal transistor, this may
decrease to a gain of 75 for 50mA or as low as 10 or 20 for 250 - 500mA.
That's right, the transistor may only have a gain or 10 or 20 when passing a heavy current. This
means the base must receive a current of 25mA to 50mA to make certain the transistor will deliver
500mA. When the transistor turns on fully, the voltage between the collector and emitter is only
about 0.2v to 0.5v. If the base is not supplied with sufficient current, the transistor will not turn on
fully and the voltage across the collector-emitter leads may be 0.6v or higher.
This is how the transistor limits the current to the device it is powering. For our application we do not
want any extra voltage to be lost across the transistor and so it must be fully turned ON. So we want
the driver transistor to deliver 50mA. This will be a low-current device and 50mA will be its
maximum rating. We can allow a gain of 100 for this device so that it requires a current of 0.5mA
into the base to turn it on fully.
The turn-on resistor is the 4k7 and when you take off the voltage drop across the collector-emitter of
the switching transistor and the base-emitter junction of the driver transistor you have about 2v
remaining from the 3v supply. This gives a base current of 0.4mA.
This is not enough to supply the motor with full current and thus the motor goes slightly slower in
the reverse direction.

THE ADVANTAGE OF A SPLIT SUPPLY

With the split-supply design there is no part of the cycle when both outputs are on at the same time.
This makes it a much safer design than the receiver in fig: 2. The section of the circuit we are
looking at, to see if both outputs are on at the same time, is shown in fig: 10.

Determining if both outputs are on

at the same time.

When the switching transistor (Q5), in fig: 7, is changing from high to low, there is a gap of about
1.2v where both outputs are off. Driver Q6 is tuned on when the input line is above 3.6v, and driver
Q7 is turned on when the input line is below 2.4v.

SIMPLIFYING THE SPLIT-SUPPLY CIRCUIT

There are some unnecessary components in the circuit of fig: 7 and by clever re-designing, these
can be eliminated. This seems surprising for a mass-produced item but sometimes the designer has
not carried out the final step of a design. This is to look at each component and say "Is this part
necessary?" If you are not sure, remove it and check the operation of the circuit. If the circuit
operates ok, the component may not be necessary. There are 10 components in the circuit of fig: 7
that can be removed and a further 5 can be changed in value when a re-design is carried out. The
result is shown in fig: 11.
 The 27MHz single-channel receiver with the author's modifications.

The first two components to be removed are the 390R and 10n on the emitter of the first transistor.
The 220R is increased to 680R as shown in fig: 11 to produce the same biasing. The reason why
the 10n can be removed is because it is effectively across the 390R (via a 47n) so that the join of
the 220R and 390R is effectively at rail impedance to high frequencies.
This means the 39p can be connected to the positive rail and the 390R can be incorporated with the
220R. By using 470p as the high frequency filtering component in each of the two audio amplifier
stages, the 10k and 4n7 filtering components can be eliminated. It may also be possible to remove
one of the audio amplifier stages when the 0.47u electrolytic is used as it is much more effective
than the 15n charging the 10u.
The 15n and one of the diodes is not needed when the charging electrolytic is 0.47u. The switching
transistor Q5 is not required, however it does invert the signal so that when it is removed, the
resistors to each of the driver transistors must be changed so that the output driving the car in the
forward direction delivers full power and the reverse output delivers about 80%.

2-CHANNEL LINK $10.00 from Talking Electronics

A number of 2-Channel 27MHz links are available on the web as pre-built modules at very low cost.
They are intended for remote control cars but the trend is now for 4 or 5 channel links, so these are
available for $10.00. Email Colin Mitchell to buy a Tx/Rx link And get a 27MHz FSM to test the
output for $6.50
You may want to control something at the far-end of a model railway layout and running cables may
be practically impossible.
Or you may want to control something that moves around your layout.
This is an ideal way to solve the problem. The range is about 10 metres (tested with 3v on the
transmitter).
The modules come with whip antennas - spring-steel wires.
 The resistors are different to the markings on the board
The first surface mount transistor is "CR" (2SC945)
The second surface mount is an oscillator chip - not a transistor!!!
This saves about 8 components.

The diode simply prevents the 1kHz switch delivering a voltage to the output of the IC. It does not
have any effect on producing the 250Hz signal. It is just a "gating diode."
The 3-pin chip could be a very small microcontroller that has been programmed to produce 250Hz
when it detects a voltage on the output pin. The appearance of the 250Hz indicates the output is
generated by a higher frequency and is divided-down.
With 15k, the output has some 1kHz segments in the high part of the waveform when 250Hz
is being delivered. With 1k5, the top of the 250Hz waveform is very smooth.
This IC replaces at least 10 components in a two-transistor square-wave arrangement and this
saves time, space and money.
The surface-mount transistor produces the 27MHz carrier when the 1kHz from the IC is HIGH. This
is because the 1kHz turns the transistor ON during the HIGH periods of the waveform.
The oscillator produces a sinewave and the feedback is the 10p.
The 39p is effectively across both windings and this forms a tuned circuit with a frequency of
27MHz.
A tiny amount of this waveform is picked off by the 10p and passed to the base where the signal
delivered to the base turns the transistor ON more and more until it cannot turn on any more. At this
point in the wave, the signal via the 10p ceases and the transistor turns off. The collapsing
magnetic field delivers its energy to the 39p to charge it and this creates the second half of the
waveform. And the signal from the 10p is opposite to previously and it has no effect at all on the
transistor. The transistor plays no part in this portion of the wave. Adjusting the ferrite core changes
the frequency slightly and this is done when the transmitter is a long way from the receiver so you
can detects when the transmitter is operating at exactly the correct frequency. You use the weak
reception to make the final adjustment.

The receiver board

The receiver is just two IC's and a few surrounding components
 The two outputs can be used to reverse a motor or each output can be used to turn ON a
device.
When there is no transmission (reception) both outputs have zero volts.
For Forward, one output goes high and the other goes low.
The voltage lost across the output FETs is only a few millivolts (about 3 to 5mV).
The output FETs can handle about 200mA to 300mA.
Each output can be used to turn ON a separate motor:

You don't have to buy these modules. You can use the transmitter/receiver from a toy car that no-
one wants any-more. (some of them are 4 channel).
You can operate sound modules, lights, gates, points and anything up to 6v and 200mA.
Every module is different with different circuitry and chips. This discussion is just an example of how
the link works.
The LC117A chip, TMX RX 3E chip and TX 3E IC are not available.

A MULTI-CHANNEL LINK
A multi-channel link is considerably more complex than a single channel design but it offers the
possibility of designing a project that has more features. The multi-channel transmitter shown in fig:
12 has forward, stop, reverse as well as left, centre, right steering.

A multi-channel 27MHz transmitter

This represents 6 channels and they are created by changing the mark-space ratio of a square
wave oscillator as well as its frequency.
The photo shows the components on the PC board:
 The 6 (4) channel transmitter board

When the transmitter is not operating, the receiver picks up hash (background noise) and no
outputs are activated. This represents the STOP function. When the forward function is selected on
the transmitter, the square-wave oscillator operates at its high frequency setting, with an equal
mark-space ratio.
If left-turn is selected at the same time, the mark-space ratio is altered to 1:3 while the frequency
remains the same. If right-turn is selected, the mark-space ratio is 3:1, with the same frequency. If
the reverse function is selected, the frequency of the oscillator is reduced to half and if the centre
steering is selected, the mark space ratio is 1:1. If the left steering is selected, the mark-space ratio
is 1:3 and if right steering is selected, the mark-space ratio is 3:1. To understand how the channels
are produced, you need to know how a multivibrator works.

HOW A MULTIVIBRATOR WORKS

The multivibrator in the transmitter consists of transistors Q2, Q3 and the surrounding components.
This is shown in fig: 20.
You will notice the symmetry of the circuit and this produces an output waveform that is either HIGH
or LOW. The circuit changes from one state to the other very quickly and this produces the fast rise
and fall of the waveform and thus its square nature. The HIGH part of the waveform is called the
Mark and the LOW is the Space, as shown in fig: 15. A square wave with a 1:1 output has the
length of the mark equal to the space.
For the transmitter in fig: 12, the output of the multivibrator for the Forward function is shown in fig:
14. We can take this as the reference waveform as all the other waveforms will be a multiple of this.
For instance, if the left-turn is selected while in the forward direction, the waveform changes to that
shown in fig: 15.
Note the short period of time the waveform is HIGH compared to the LOW time. If this waveform is
passed into an integrating network, the percentage of time it is high can be determined and an
output activated. This is what the chip does in the receiver.
It determines one of six functions and produces outputs to steer the car in the left or right direction
and/or drives the car in forward or reverse. It also detects when the transmitter is not operating and
stops the car. If the forward-and-right controls are selected the waveform is shown in fig:16.
When reverse is selected, the multivibrator operates at half the frequency due to the 82k resistor
added to the base of the two transistors in the multivibrator. The resulting waveform for reverse is
shown in fig: 17. If reverse-and-left is selected, the waveform is shown in fig: 18. If reverse and right
is selected, the waveform is shown in fig: 19.

THE TURN-ON CIRCUIT

The transmitter doesn't have an on-off switch. It is turned on when the forward-reverse control is
moved from the stop position. This switches a diode into circuit. The diode charges the 100u via the
4k7 to turn on the emitter-follower transistor Q1. The base rises to just below rail voltage and the
emitter is about 0.7v below this. The emitter becomes the power rail for the rest of the circuit and
while the controls are in the forward or reverse direction, the circuit is supplied with voltage and
current.

Block diagram of multi-channel transmitter.

The turn-on circuit supplies current to the rest
of the circuit when the controls are activated.

When the control is returned to the stop position (via a spring-return), the current required by Q1 to
keep it turned on is supplied by the 100u on the base and as the energy is delivered from the
electrolytic, the voltage across it reduces. This reduces the voltage across the circuit but since it is
not sending out a signal, this does not matter.
After a minute, the voltage drops to almost zero and the electrolytic is finally discharged completely
by the 1M (and 4k7 in series with it). The stand-by current drops to less than 1 micro-amp, the
leakage through the collector-emitter junction when the transistor is not turned on.

MORE ON HOW THE MULTIVIBRATOR WORKS

Transistors Q2 and Q3 form a multivibrator and the operation of this is fully covered in our books
titled Learning Electronics Book 1 and Book 2. The circuit is basically regenerative in which one
transistor turns the other off then the second turns the first off. When the circuit is first turned on,
both the bases are pulled high via the 10n capacitors but one of the transistors turns on before the
other and robs it of turn-on voltage. But the transistor cannot stay turned on forever as the 10n
capacitor becomes charged and as it turns off, it sends a pulse to the other transistor.
The second transistor turns on and completely removes the turn-on voltage from the first transistor.
Eventually the second transistor cannot remain fully turned on due to the 10n becoming charged,
and starts to turn off. This sends a pulse to the first transistor and it starts to turn on. Each transistor
has a gain or amplification factor of about 100 and when we say one transistor begins to turn off
slightly, this change is passed to the base of the opposite transistor and the result is magnified 100
times on the collector. This is then passed to the base of the first transistor and suddenly a tiny
signal gets passed back as a huge signal. That's why each transistor reacts so quickly and the
result is a very fast change from one state to the other. This is shown in the shape of the output
waveform.
The rise and fall times are very short and the sides of the square wave are very steep. The
frequency of the output is determined by the value of the components on the base. This includes
the base resistor and the capacitor connecting to the opposite transistor. In the circuit of fig: 12, the
capacitors are fixed at 10n and the resistors are changed.
An increase in resistance causes the capacitor to take longer to charge and decreases the
frequency of the circuit. The output of the multivibrator is passed to the base of the RF output
transistor where it controls the on/off time for the transmitter. When the transmitter is turned on, a
27MHz frequency is injected into the base of the RF output transistor via a 47p from the crystal
oscillator. This crystal oscillator is made up of transistor Q4 and its surrounding components.
The transistor is turned on via the crystal and 22uH inductor. The crystal is equivalent to about 20p
and the resistance of the inductor is about 1 ohm. The emitter is held fairly rigid via the 47p and the
transistor gets a very short pulse from the crystal. This puts a pulse of current through the coil and
the current creates magnetic flux. As soon as the pulse ceases, the magnetic flux collapses and the
inductor produces a voltage in the opposite direction and passes the waveform through the 47p to
the base of the RF output transistor. It also passes the waveform through the crystal to turn off the
oscillator transistor Q4. When the transistor is turned off, it does not put any load on the inductor
and the amplitude of the waveform is fairly large. After a short period of time, this waveform ceases
and the transistor gets turned on by the 120k base bias resistor.
This injects another pulse of current into the inductor and the cycle repeats. The inductor creates
the time delay for the waveform as it takes time for the current to convert to magnetic flux then back
into a voltage in the opposite direction. This time-delay approximates to about 27MHz and the
crystal locks it on to the frequency of 27.240 by exhibiting a larger capacitive effect at this exact
frequency. This is how the circuit is pulled into line and kept at an exact frequency, even though the
supply voltage may decrease or the temperature may rise.
The 27.240MHz waveform is passed to the RF output transistor and the transistor is turned on and
off at the frequency of the multivibrator. The transistor is in common emitter mode as evidenced by
the 10n on the emitter.
The impedance of this capacitor at 27MHz is very small compared to the 100R and the emitter
considers it is connected to the negative rail as far as the high frequency is concerned. The 27MHz
waveform on the base is amplifier by the transistor and appears on the collector in magnified form.
The 22uH inductor on the collector prevents the signal passing to the power rail. It does this by
producing a "back-voltage." As the transistor turns on, the current through the inductor increases
and magnetic flux is produced in the coil that cuts the other turns of the coil and this induces a
voltage and current in them that is in opposition to the current being delivered. The result is a
reverse voltage is produced that makes it difficult for the forward voltage to enter the coil.
This means the forward voltage gets larger and larger in an attempt to enter the coil and the result
is a large voltage appearing on the collector of the transistor. This voltage passes through the 47p
to a tuned circuit made up of a 11 turn inductor and 15p capacitor. These are designed to match the
high impedance of the output of the transistor to the low impedance of the whip antenna. Matching
is required to get the maximum signal to pass into the antenna. This completes the coverage of the
sections in the transmitter.

THE MULTI-CHANNEL RECEIVER

The signal from the transmitter is picked up by the receiver as bursts of tone between hash. Viewing
the signal on a CRO (Cathode Ray Oscilloscope) will look something like fig: 23.

The signal from the multi-channel transmitter will consist

of a regular waveform between background hash.

The receiver is required to pick out the signal from the noise and it does this by a process called
integration and differentiation where the signal is detected due to its regular nature and this is used
to charge a capacitor.
Another circuit determines the length of time the tone is present and these are combined to
determine the nature of the control signal. Most of the circuitry for doing this is locked inside the
chip in the receiver and the only components we can see are the external items on pins 10, 1 and
19. These determine the frequency detected by the chip and the length of the "highs," but all the
rest of the signal processing is done inside the chip. The chip detects the waveforms shown in figs
14 - 19 and turns on the appropriate outputs.

A multi-channel 2MHz receiver

 The 27MHz receiver PC board

Two outputs drive the motor in the forward/reverse direction and 4 outputs drive the transistors for
the steering motor. The steering motor is simply a rotary actuator. This is similar to the armature of
a motor, positioned inside a circular magnet.
The armature does not need brushes as it will only turn about 45° in one direction and 45° in the
opposite direction, depending on the direction of the current. The output of the shaft will be
connected to a lever to steer the front wheels.
The chip controls the two diagonally opposite transistors for the clockwise and anticlockwise
rotation to get left and right steering. All the rest of the circuit has been previously discussed and
the only new feature is the tapping at 4.5v for the motor. A diode on the 4.5v rail drops the voltage
to 3.8v and the two output transistors drop a further 1v, so that motor receives about 2.8 to 3v.

Here are some remote control items, shown on the web, by a hobbyist who disassembles devices
and makes a new project:
 Some of these components were used to build a project and present it the web.

A 27MHz WALKIE TALKIE

An Overview
Walkie Talkies are the next logical step in this discussion. They show how a crystal oscillator can be
used to transmit voice. Transmitting a voice via a crystal locked oscillator is not easy. This is
because the crystal is locking the frequency and it is very difficult to shift it. The only way to do it is
to add the audio as an amplitude component so that the amplitude of the oscillator rises and falls
with the audio signal but its frequency does not change.

The only problem with this mode of transmission is interference. Electrical noise entering the
airwaves is also a varying amplitude waveform and the receiver will pick this up at the same time
and produce a very noisy result. This is one of the reasons why walkie talkies are so noisy.
However it is a starting point for learning about transmission and the circuit in fig: 24 shows how the
audio is added to the carrier.
 A 4-Transistor Walkie Talkie

Nearly all the components in the 4-transistor circuit are used for both transmitting and receiving.
This makes it a very economical design. The frequency-generating stage only needs the crystal to
be removed and it becomes a receiver.
The operation of this circuit coincides with our discussion on receiver circuits at the beginning of this
article where we said the receiver was oscillating all the time, similar to a weak transmitter. A 390R
is added to the emitter of the oscillator stage to reduce the activity and turn it into a receiver. The
next section of the circuit is called a building block.
It consists of three transistors directly coupled to produce an audio amplifier with very high gain.
The first transistor is a pre-amplifier and the next two are wired as a super-alpha pair, commonly
called a Darlington pair to drive the speaker transformer.
The third block is the speaker. This is a separate item because it is used as a speaker in the receive
mode and a dynamic microphone in the transmit mode. A speaker can be used in reverse like this
and it is called a dynamic microphone because of the coil and magnet arrangement. When you talk
into the cone, the movement of the voice coil in the magnetic field produces a few millivolts output.
This can be coupled to a high gain amplifier to get quite good results.
When the walkie talkie is in the receive mode, the first transistor is configured as a receiver and the
audio is picked off the 4k7 load resistor via a 0.47u electrolytic. It then passes through a volume
control and into the three transistor amplifier. The speaker transformer couples the amplifier to the
speaker and we hear the result. When the walkie talkie is in the transmit mode, the speaker is
placed at the input of the audio amplifier.
The audio is then amplified and the waveform appears as THE SUPPLY VOLTAGE FOR THE
TRANSMITTER STAGE. The crystal is connected to the first stage and the gain of the transistor is
increased by removing the 330R and only using a 56R for the emitter resistor.
The speaker transformer is not used as a transformer in this mode but as an INDUCTOR to couple
the output of the audio amplifier to the power rail and the signal developed across the winding is
passed to the transmitter stage as the supply voltage for the transmitter. As the waveform rises and
falls, it changes the gain of the first stage and thus the amplitude of the transmitted signal. This is
how the signal becomes an Amplitude Modulated (AM) Radio Frequency (RF) signal.

THE WALKIE-TALKIE CIRCUIT IN DETAIL

In the receive mode, the first transistor is configured as a low-level oscillator. The base is tied to
earth via a 39n capacitor. This makes it a common-base configuration and the gain of the transistor
is high. The input (the collector) is also high, whereas the input (the base) of a common-emitter
stage is medium to low.
If this type of stage were used, the antenna would not be as sensitive in detecting up a signal. The
feedback for the transistor is provided by the 33p between collector and emitter. The emitter has a
330R and 56R in series to keep the gain low.
The circuit starts up and oscillates due to a tuned circuit on the output of the RF transformer. The
transistor detects this oscillation on the primary side of the transformer and passes the signal to the
emitter via the 82p, where the gain of the transistor increases the amplitude of the signal to a
medium level. If the amplitude is too high, the stage will not be responsive to the surrounding
signals.
Any nearby signals of the same frequency will increase and decrease the current taken by this
stage and the information on the signal will appear across the 4k7 load resistor as a varying
voltage. The 0.47u picks off the voltage and passes it as an audio signal to the volume control and
finally the 3-transistor amplifier. The 4n7 between base and ground of the first amplifier transistor is
designed to remove any high frequency signals and the output of the transistor goes to a super-
alpha pair to drive a speaker transformer.
The speaker transformer matches the output of the transistor to the 8 ohms of the speaker.
Matching is done by the transformer having a turns ratio. It has 525 turns for the primary and 75
turns for the secondary. The purpose of the transformer is to convert a high voltage (about 7v), with
low current to a low voltage (about 400mV) at high current. This is what the speaker requires. It
needs a high current to pull the cone into the magnetic field. The remaining components are biasing
components or capacitors to remove the high-frequency signal.

SETTING THE BIAS FOR THE 3-TRANSISTOR AMPLIFIER

The circuit in fig: 25 shows the components that set the bias for the three transistors.

The biasing of the 3-transistor amplifier

All the other components have been left out because they do not determine the DC bias point. The
biasing starts at the base of the first transistor. It is turned ON, but not fully, by the 1M resistor until
the collector voltage falls to half-rail voltage. The 1M and 5k6 resistors are chosen so that this
occurs.
This is the ideal set-point so that the pre-amplifier transistor can amplify both the positive and
negative excursions of the signal without distortion. The super-alpha pair (the second and third
transistors in the 3-transistor amp) drops a total of 1.3v across the base-emitter junctions, leaving
3.2v across the 100 ohm emitter resistor. By ohms law, this will produce 32mA as the idle current
(quiescent current) for the audio stage.

Here is a hand-cranked walkie talkie:

The walkie talkie in transmit mode. The signal

passes from the audio amplifier to the RF stage
via the power rail

The walkie talkie in receive mode. The circuit is

conventional with the first stage feeding the
3-transistor amplifier via a volume control
THE EMITTER BY-PASS CAPACITOR
The 33u electrolytic on the emitter is called the emitter by-pass capacitor. It connects the emitter to
the 0v rail when the stage is processing a signal and the signal by-passes the 100 ohm resistor. To
see how the electrolytic works we firstly have to remove it and see why the Darlington pair has NO
GAIN. Refer to fig: 25. When a signal is fed into the base of the pre-amplifier transistor it will be
amplified about 100 times and appear on the collector. Suppose the collector voltage rises 5mV.
This will be passed to the base of the top transistor of the Darlington pair and since it is almost fully
turned on, the emitter will rise too. The emitter of this transistor is connected to the base of the
lower transistor and the base will pull the emitter up too.
The collector voltage will not change and this means the transistors will produce NO gain because
the voltage on the emitter is allowed to rise. It we hold the voltage on the emitter rigid, the pair will
give us gain. To do this we connect an electrolytic between 33u and 100u. It has the feature of
taking a long time to charge (and discharge) - compared with the rise and fall time of the signal.
When the 5mV waveform appears on the base of the Darlington arrangement, the base tries to rise
but it is fixed by the characteristic voltage of 0.7v developed across each of the base-emitter
junctions. The result is the base rises 0.1v and both transistors get turned on more. The resistance
between the collector and emitter of the output reduces and the transistor allows more current to
flow through the primary of the speaker transformer.

THE SPEAKER TRANSFORMER

A lot of discussion could be devoted to the operation of the speaker transformer as the design of a
transformer is very complex. There are two ways you can design a transformer. One is to calculate
the requirements from scratch and the other is to copy an existing design and make modifications
until the desired result is achieved. Copying and modifying is the quickest.
If you use the theoretical approach you will invariably have to modify the design to get it working
perfectly. The speaker transformer used in fig: 24 is 1k to 8 ohm. These are the impedance values
measured at 1kHz. The actual DC resistance of the primary is 42 ohms and the secondary is 1
ohm.
The DC resistance of a transformer is different to the impedance value. If the transformer was
larger, the wire diameter would be larger and the DC resistance could be as low as 10 ohm and 0.5
ohms. The impedance is the resistance as seen by the transistor at 1kHz. It "sees" a 1k load at
1kHz and a higher impedance at a higher frequency. Energy is transferred from the primary to the
secondary via magnetism.
The primary produces a magnetic flux that passes into the magnetic core surrounding the windings.
This magnetic flux cuts the turns of the secondary and produces a voltage in it.
The voltage produced is proportional to the number of turns. In our case the primary has 525 turns
and the secondary has 75 turns. This is exactly a 7:1 ratio and it means the transformer will
theoretically convert a 7v waveform at 10mA into a 1v waveform with a current of 70mA.
A small transformer like this has an efficiency of about 50 - 70% however it is performing a very big
task, matching 1k to 8 ohms and the speaker would not work if it were connected directly to the
transistor. To directly couple the speaker, the emitter resistor would have to be lower. The circuit
would then take 70mA to get the same result as with the speaker transformer. And even then the
transformer provides a much better match.

THE TRANSFORMER AS AN INDUCTOR

When the transformer is used as an inductor in the transmit mode, the speaker is not connected
and the secondary does not see a load. This means the primary does not see a "reflected" load and
the impedance of the transformer is increased considerably. The effect is the transistor sees a
higher impedance and this means it finds it easier to develop a signal across the primary.
To give a very simple analogy, the transformer (with the speaker connected) is like a very stiff
spring. When the speaker is removed, the transformer is like a very weak spring. The transistor
finds it very easy to pull the bottom end of the spring down (the top is connected to the positive rail).
When a signal is processed by the Darlington pair in transmit mode, the emitter is held rigid by the
33u and the only thing that can happen is the weak spring gets pulled down.
By referring to the circuit diagram in fig: 24, the bottom lead of the transformer becomes the power
rail of the crystal oscillator and as the voltage on the transformer rises and falls, the supply voltage
to the oscillator increases and decreases. and affects the gain of the oscillator. Now we come to the
difficult part of explaining how a voltage is produced across the primary winding. During the
quiescent (idle) mode, about 1.5v is dropped across the 42 ohm resistance of the primary. When a
signal is processed by the Darlington pair, the resistance between the collector and emitter is
reduced and a higher current flows.
The action of this current increasing creates an expanding magnetic flux in the transformer and this
flux cuts the adjacent turns of the primary and induces a voltage in each of the turns in the opposite
direction. This means the voltage produced by the transistor has to be greater, in an attempt to
pass current into the inductor.
This voltage is picked off the inductor and passed to the first stage in the circuit and becomes the
power rail. The fluctuating power rail alters the gain of the stage and amplitude modulates the
27MHz signal to produce audio on the carrier. The result is an Amplitude Modulated (AM) Radio
Frequency (RF) signal.

MORE 27MHz WALKIE TALKIE CIRCUITS

The following 3 circuits have been taken from different Walkie Talkies and show designers have
included a crystal, a call button and an LM386 audio amplifier chip into their designs. You can take
the different features from one circuit and incorporate them into your own design.
Just remember, receiver circuits that are only for receiving a signal are designed to pass very little
current so they are very sensitive. Walkie Talkie circuits need the fist state to deliver an output as
well as receive a signal so they have to be designed with both transmit and receive capabilities.

27MHz Walkie Talkie without Crystal

 27MHz Walkie Talkie with Call

27MHz Walkie Talkie with LM386 Audio Amplifier

49MHz WALKIE TALKIES

Two bands have been allocated for walkie talkies and remote control equipment. These are the
27MHz band and 49MHz band. The 49MHz band has slightly better performance due to the short
antenna being closer to the wavelength of the signal. The two bands allow more remote control cars
to be raced together without interference between the cars.

FURTHER USES
All of these circuit can be found in remote-control toys from your local department store. Simply buy
a remote control car and give it to a youngster to play with. After a day or two he will lose interest
and you will be able to pull it apart and adapt it to your own use.
To create a private channel, simply replace the crystal with one of a slightly different frequency and
retune both the transmitter and receiver coil. The multi-channel receiver has even most possibilities.
You can control four different devices directly and even more by gating the outputs. The simple
27MHz link will be used with one of our Talking Electronics FM transmitters to turn it ON and OFF
remotely.
The 27MHz transmitter will work up to 60ft (20m) and will allow you to turn off a transmitter to give it
added security from being detected. The receiver will have to be designed to turn on for 0.5sec
every 10 seconds to detect if a turn-on transmission is being sent and the whole circuit will then
shut down to conserve power if a reception is not detected.
This means you will have to transmit for at least 10 seconds to be sure the receiver picks up the
signal.

On the next page we cover some more 27MHz transmitter circuits, and on P3 we cover some
303MHz links.

P2 P3

P1 P2 P3(303MHz)
Home

CIRCUIT A
Circuit A shows a 27MHz transmitter circuit without a crystal. The main reason for a crystal is to
comply with the strict transmitting laws in most countries. A fairly narrow band has been allowed at
27MHz and to keep within this area, a crystal has been used. Since a crystal is not an expensive
component when bought in the millions, manufacturers have included them in their circuits to get
instant approval.

However the important reason for using a crystal is to get reliable operation.
When a circuit does not have a crystal, the oscillator is said to be "voltage dependent" or "voltage
controlled" and when the supply voltage drops, the frequency changes.
If the frequency drifts too much, the receiver will not pick up the signal.
For this reason, a simple circuit as shown in circuit A is not recommended. We have only included it
as a concept to show how the 27MHz frequency is generated.
The two transistors are doing two things at the same time. The second transistor is a self-contained
oscillator and it gets its feedback (to oscillate at 27MHz) from the transformer. The main coil is the
8t section and the feedback to the base is 4 turns.
The first transistor is also connected to the second transistor and the two form a low-frequency
oscillator in which the first transistor forms the timing for the oscillator and the second transistor
provides positive feedback.
The first transistor turns on via the 1M and the transistor sees this as pulling the base "down." The
collector of Q1 pulls the base of Q2 "up" and Q2 turns ON. This causes current to flow in the 100R
and the voltage on the right side of the 6n8 falls. The capacitor tries to make the left side fall too
and turn on the first transistor even more. This happens until Q1 cannot turn on any more and the
6n8 charges a little more. This turns off Q! a small amount and the to transistor begin to turn off.
The frequency of the tone is determined by the value of the 6n8. All the time that this is happening,
Q2 is oscillating at 27MHz and it is just being "DC shifted" up and down.
The tone consists of short spikes, unlike the tone produced by Circuit B, which has an almost even
mark-space ratio.
The second circuit comes from a GS Remote Control Car. It does not have the 2k2 current-limiting
resistor and you can experiment to see which circuit consumes the least current and has the best
range.
See GS Remote Control Car Receiver Circuit below.

A 27MHz transmitter
(receiver for this circuit HERE)
 Circuit A - Birds Nest

Circuit A was quickly constructed on a piece of copper board to act as an earth plane and to make
sure it worked and to see if any improvements could be made. If a circuit works well in an open
format such as this, you can be sure it will work better when constructed on a printed circuit board
where the circuit is much "tighter" and the impedances are lower. The layout above is called a
"Birds Nest" and allows rapid modifications to be made and you can touch the parts to see if your
hand capacitance changes the frequency or stops the circuit working.

CIRCUIT B
Circuit B also produces a tone. But this time two transistors are used in a multivibrator arrangement,
in which one of the transistors is used to turn the third transistor on and off.
Circuit A is a very efficient and clever circuit and requires less components. That's why you must
study all types of circuits before producing your own design as simplicity is the secret to success.
The tone is used by a receiver to determine the signal is coming from the chosen transmitter. The
receiver can have a detector stage to detect the exact frequency or the tone can be used to change
the state of a stage. This is called integration, where the energy from the pulses from the tone are
added together to charge or discharge a capacitor.
Circuit B comes from a Russian design, and it uses Philips transistors!
We tested the output with our Field Strength Meter MkII and found it had a good output. Details of
Field Strength Meter MkII are discussed below.
But the circuit has some poor features. The poorest feature is the printed-circuit coil. This type of
coil has the lowest value of "Q." "Q" is the name for the "Quality factor" for a coil and it effectively
determines how much amplitude you will get. Quite often the output of a coil will be higher than the
voltage being supplied to it and this gives the value of "Q."
The other poor design is turning the emitter of the third transistor on and off. A better solution is to
drive the base as has been done in Circuit A. This allows full voltage to be applied to the stage.
Here is the circuit:
The topside of circuit B
 The underside of circuit B

HOW THE CIRCUIT WORKS

Circuit B consists of two blocks. Block 1 is a multivibrator and this has an equal mark/space ratio to
turn the RF stage on and off.
We have covered the operation of a multivibrator in the electronics course on Talking Electronics
website, in the subscription section.
The only thing you have to know for this circuit is the fact that the middle transistor turns on for 50%
of the time and the voltage between the collector and emitter drops to less than 0.3v This voltage is
too low for the third transistor to operate and thus the RF stage is turned off.
The second building block is the RF oscillator.
The actual operation of the stage is very complex and beyond the scope of this discussion.
However some of the points are as follows:
The feedback to keep the stage operating is provided by the 27p capacitor.
The frequency-producing items are the coil (made up of the full 7 turns) and the 47p air trimmer.
These two items are called a parallel tuned circuit. They are also called a TANK CIRCUIT as they
store energy just like a TANK of water and pass it to the antenna.
The base is kept rigid by both of the 4n7's. In other words, the base does not move.
The stage is turned on by the 22k and 15k voltage dividers. A voltage of 5v is produced at the join
of these two components. The voltage on the emitter will be 0.6v lower.
This will cause current to flow in the 220R and also in the 3t winding. These turns will produce
magnetic flux that will cut the other 4 turns and produce a voltage in them. This energy will pass to
the antenna and some of it will charge the 47p and in doing so the voltage on the collector will
reduce. This voltage will be passed to the emitter via the 27p and this will turn the transistor on
more. This will continue until the coil cannot produce any more voltage and the transistor will begin
to turn off. The collapsing magnetic flux in the 3 turns will cut the 4 turns and produce a voltage in
the opposite directions and the other half of the cycle will be produced.
The frequency of the circuit is adjusted by the 47p air trimmer.

RECEIVERS
The following receiver matches up with Circuit B above.

27MHz Receiver

HOW THE CIRCUIT WORKS

The circuit consists of a number of building blocks and these can be identified when a capacitor
separates one stage from another.
The first stage is actually a 27MHz oscillator with a very small output due to the 4k7 resistor
connecting the stage to the positive rail. This allows very little current to enter the stage and the
transistor operates on a very "delicate basis."
When a circuit is oscillating and delivering a signal to the air surrounding the antenna, any other
signal entering the same surroundings will cause an interference with the generated signal and the
circuit will find it more-difficult to deliver a signal, especially when the signal has the same
frequency. This will cause the voltage on the collector of the transistor to alter and produce a signal
that can be passed to further stages of amplification.
The 5v1 zener is designed to keep the voltage on the first stage constant as the transistor is
oscillating and is a voltage-controlled oscillator.
All the components in the first stage are designed to make it very sensitive to detecting a signal.
Normally, all the surrounding signals upset the clean sine-wave produced by the stage and the
result is a lot of "noise" or "hash" or "background noise" at the "pick-off" point.
If the 27MHz signal produced by a transmitter contains a tone, this tone will appear at the "pick-off"
point along with the hash.
The frequency of the hash is fairly high and on the second stage there are three components to
remove it.
The first is the 1k5 resistor. This, in combination with the 47n, has a slight effect.
Next, the 15n between base and ground will remove high frequencies. And finally the 2n2 will send
any amplified signal back to the base for cancellation. This capacitor has a greater effect on
canceling high frequencies.
The third and fourth stages also remove some of the high frequency component of the signal and
the result is a clean signal with only the tone appearing on the base of the fourth transistor.
This signal has a large amplitude and will turn the transistor on fully.
The transistor normally sits with the collector very close to rail voltage due to the low value of
collector resistor and this means transistor Q5 is not turned on.
The 47u gets charged via the 1k5 resistor and the relay is not energised.
When the fourth transistor sees a tone, it turns on at the frequency of the tone and this puts pulses
of short-circuit across the 47u and it rapidly discharges.
As it discharges, the voltage on the collector drops and this turns ON Q5 to operate the relay.
When the tone stops, the 47u rapidly charges via the 1k5 and the relay switches off.
The photo below shows a switch added to the PC board and a LED connected to the output of the
relay to test the receiver.
The pot in the centre of the board adjusts the sensitivity of the receiver.

Receiver for transmitter in Circuit B

The relay can be latched ON via the following circuit but it cannot be turned on remotely. The power
has to be disconnected to release the relay. This is only suitable for a "one-shot" operation where a
device has to be turned on only once.

Relay turns ON and stays ON

(Latching Circuit)

If a long tone is required to turn on the relay (to prevent false triggering), the following circuit can be
used. The 100u electrolytic takes about 2 seconds to discharge via the 10k resistor, as the 4k7
adds to the time-delay, since it is providing charging-current that the transistor has to overcome.

2-second tone to turn relay ON

The following circuit allows a single channel transmitter/receiver to turn an appliance on and off by
sending a short pulse to turn a circuit on and a long pulse to turn a circuit off.
This is handy when you cannot see the result of your operation. A simple toggle operation is not
suitable as you do not know the state of the output at the start of the operation.
By sending a long pulse, you definitely know the output will be OFF and you can then control the
output remotely.
A short pulse is less than 0.25 sec and a long pulse can be any length longer than 1 second.
These times can be adjusted by changing the value of the components.
When a short tone is received, the lower 47u discharges and pulls the base of the BD136 towards
the 0v rail and turns the transistor ON. This activates the relay and the contacts take the 4k7 to the
0v rail to keep the transistor ON.
During this time the top 47u charges via the 100k but not enough voltage appears across it to turn
on the BC557 transistor.
If the tone appears for a long period of time, the top 47u charges and turns on the BC557 and the
voltage between the emitter/collector terminals is less than 0.3v. This voltage is too low for the
BD136 to remain on and it turns off.
When the tone is turned off, the BC557 remains on for 1 second and then turns off.
The circuit is then ready to be activated again.

Short tone = ON Long tone = OFF

The circuit above can be added to many different receiver circuits, thus using only one output to
provide an on/off function.

GS REMOTE CONTROL RECEIVER

This circuit is the receiver for GS Remove Control transmitter shown in Circuit "A" above.
The purpose of presenting a number of circuits is to show the basics of how this type of circuit
works.
The secret behind a receiving circuit is to create a "front-end" that is actually oscillating at the
frequency to be detected and it transmits a very weak signal out the antenna. When a signal of the
same frequency is detected by the front-end it takes more current and less current according to the
tone being carried by the 27MHz signal (as the tone is actually increasing and decreasing the
strength of the signal). This amplitude appears on the output of the "front-end" and is picked off via
the 39n capacitor. It is then amplified by two stages. The 10n on the collector of the second
transistor is designed to remove the "hash" or background noise. This signal then turned into a DC
voltage by charging a 1u electrolytic and the negative portions of the signal are removed by the
diode. When no signal is detected, the transistor is not turned on and the motor operated in the
forward direction. A signal turns on the transistor and the other two transistors in the half-bridge
are turned ON to reverse the motor.
 (transmitter for this circuit HERE)

2 CHANNEL TRANSMITTER
The next circuit is a 2 channel transmitter.
This circuit does not use a crystal but has a clever feature of using the two push buttons to turn the
circuit on when it is required to transmit.
Click HERE for RX-3 IC datasheet .pdf

We have already discussed the operation of a circuit such as this, with a multivibrator and RF
oscillator. The only new feature is the arrangement for producing two different tones.
The receiver requires a 1kHz and 250Hz tone for the forward and reverse outputs. The frequency of
the multivibrator is determined by the value of resistance on the base of each transistor. The
multivibrator is driven directly from the supply with the forward button and via a 150k for the reverse
frequency.

2 Channel Transmitter PC board

2 CHANNEL RECEIVER
 Circuit for the RX-3 IC

The circuit for the receiver has not been taken off the printed circuit board, however a general circuit
is provided in the datasheet for the IC and this has been reproduced above.
Both output of the chip cannot be HIGH at the same time as this will destroy the transistors in the
"H-bridge."
For the forward direction, the forward output is HIGH and this turns on Q9, Q11 and Q13.
For the reverse direction, the backward output is HIGH and this turns on Q8, Q10 and Q12.
This toy remote control car cost less than $8.00, but a defect in the design was noted.
The motor would reverse approx every 2 minutes for a short period of time, even though no
transmitter button was pressed and the motor would operate in bursts when the car was distant
from the transmitter. The interference was not from any electronic device in the home as the
receiver was taken to an open space and it still faulted. The first transistor was removed and the
fault did not occur. This means the RF transistor is generating a fault that is detected by the chip to
turn on an output.
This could be due to the chip detecting a frequency of 1kHz or 250Hz to turn on an output. Random
noise could be in this range and that's why the RX-3 receiver chip is unreliable.
Maybe that's why the car was $8.00!
Another point of comparison: the RX-3 receiver circuit consumed 4.4mA at 4.5v, while the RX-2B
receiver consumed 0.7mA at 3v.

4 CHANNEL TRANSMITTER
This circuit uses the TX-2B RX-2B chipset discussed on the previous page. The chip has 5
channels and the circuit uses 4.
Click HERE for TX-2B RX-2B chipset datasheet .pdf

4-Channel Transmitter PC Board

TX-2B circuit on datasheet

4 CHANNEL RECEIVER
The receiver using the RX-2 chip:

4-Channel Receiver PC Board

 RX-2B circuit on datasheet

FIELD STRENGTH METERS

There are five pieces of test equipment you can buy or build to test the output of a transmitter.

1. LED Power Meter, Detects RF energy and indicates the result on a multimeter set to 2v or 10v
scale.
2. Field Strength Meter MkI. FSM MkI detects RF energy and indicates the result on a multimeter
set to 10v scale.
3. Field Strength Meter MkII. FSM MkII has a scale 26MHz to 50MHz. By turning a pointer
connected to an air trimmer, the frequency of a transmitter can be determined.
4. Field Strength Meter MkIII - uses a 600 ohm Balance Movement.
5. 27MHz Walkie Talkie - purchase from a toy store.

When working with a transmitter, the first thing you will want to do is determine if the transmitter is
producing RF.
Talking Electronics has three kits for this.
1. The LED Power Meter costs less than $2.00 and connects to a multimeter set to 2v or 10v range
or you can use the 0.5mA range. It connects directly to the antenna of the transmitter and a LED
illuminates if the transmitter is producing more than about 30milliwatts. If the transmitter is
producing less than 30mW, the needle on the multimeter will deflect, but the LED will not illuminate.
The photo below shows the LED Power Meter connected to a mini Multimeter. These are available
from "$2.00 shops" for less than $10.00

The multimeter in the photo has a

sensitivity of 2,000 ohms per volt.
This means the resistance inside
the meter is 20,000 ohms when the
pointer is on the 10v scale.
This type of meter is called a low
sensitivity instrument and is ideal for
the job we are doing.
If a high impedance instrument is
used, it can pick up stray RF and
produce a false reading.
A high impedance instrument can
be 20,000 ohm per volt, 50,000
ohms per volt or 100,000 ohms per
volt (commonly called a FET meter.)
Digital multimeters can have higher
input impedances.

LED Power Meter connected to a

mini multimeter

2. If you want a more sensitive detector, use .

Once you know a transmitter is producing RF (a signal), you can tune it to a particular frequency.
To do this you will need Field Strength Meter MkII.
When FSM MkII has been modified as shown below, it can be calibrated.
This will allow you to set the frequency of any transmitter that does not use a crystal.
To detect a tone from a transmitter, use a 27MHz or 49MHz Walkie Talkie. The tone will be heard in
the speaker.
 FIELD STRENGTH METER MkII Modification

3. Field Strength Meter MkII can be modified to detect transmitters in the range 27MHz to 49MHz by
placing a 12 turn inductor on the bottom of the board. This is made by winding 12 turns of 0.25mm
wire on a 2mm x 5mm ferrite slug. The 47p capacitor in series with the 47p air trimmer is "shorted
out" under the board as can be seen in the photo above. The link to the coil on the board is
removed so that it effectively comes out of circuit. No other parts on the board are changed.
You will need a transmitter with a crystal to calibrate the Field Strength Meter. You can then use the
FSM to adjust any of the transmitters that do not have a crystal.
Field Strength Meter MkII can also be used to determine the relative output of each transmitter by
using the same length antenna on each transmitter and holding FSM MkII at the same distance
from the transmitter. The three LEDs on the PC board will show the relative signal strength.

4. You can buy a Remote Control Car or Walkie Talkie to get a transmitter and receiver.

5. Field Strength Meter MkIII uses a 600 ohm movement (1mA FSD) but almost any movement will
be suitable.
The size and shape of the coil is extremely important and the photo shows slight stretching on the
last turn to peak the circuit.
 FIELD STRENGTH METER MIII

Field Strength Meter MIII Circuit

The 100p and 18 turn coil form a tuned circuit that oscillates at a particular frequency. The
frequency at which the components oscillate is changed slightly by the 47p air trimmer. The signal
then passes into a 2-diode rectifier with one diode passing the voltage to the meter and the other
diode discharging the 47p on the negative half of the waveform. The 100n across the meter stores
and smoothes the voltage for the 1mA (Full Scale Deflection) movement.
This circuit shows the amazing ability for two passive components to "amplify." The 100p and 18
turn coil form a TUNED CIRCUIT and when the incoming frequency is exactly the frequency at
which these two components oscillate, the output rises considerably.
If you have transmitter, you can set up the circuit to detect an exact frequency by winding the 10cm
tinned copper wire antenna around the antenna of the transmitter. Each centimetre gives about 2p
of capacitance and this is sufficient to connect the two together "RF wise."
The circuit requires 18 turns but if you add one turn, you can stretch the coil to get the circuit to
peak then remove it later.
Finding the resonant frequency of the coil and capacitor is a very difficult thing to do as the peak
comes and goes in less than 1/10mm of stretching the coil.
In addition, you cannot touch the coil or be anywhere near the circuit when making the adjustments
as you body completely "soaks away" the energy.
You have to use a plastic knitting needle and move the end turn very slowly while watching the
meter.
You will see it move from zero to more than half way as the adjustment is made.
You now have a piece of test equipment that will indicate when a transmitter is operating at an
exact frequency.
If you want to know if the transmitter is producing RF, you will need Field Strength Meter MkI as it
purely detects RF.
Talking electronics has designed a PC board with Field Strength Meter circuit to detect 27MHz.
Most of these transmitters are very low power and getting a reading on a meter (actually called a
"movement") is very difficult.
To help get a reading we have added a transistor amplifier.
The result is:

27MHz FSM
Click HERE to go to the project.

P1 P2 P3(303MHz)

P1 P2 P3
2N3563.pdf 9014.pdf 9018.pdf
Home

We have covered 27MHz (and 49MHz) links on P1 and P2 of this article and shown how to produce
a simple circuit (or buy a toy for less than $10.00) and get 4 or 5 channels.
We also showed how to produce on/off from a single channel and how to detect 27MHz with a Field
Strength Meter.

27MHz can transmit at least 100 metres and provide a reliable link as proven by the countless
garage-door openers on the market.
But 27MHz transmitters are fairly bulky and need a short antenna to produce a good range.
They are not suitable for short range applications where an antenna is not wanted. These include
anything you want to put in your pocket, such as emergency call-buttons, garage door openers,
remote car locking, alarm activation/deactivation etc.

For these applications the 303MHz frequency is ideal.

The antenna (the radiator) can be etched onto the PC board and provide an amazing range.
We have tested a 303MHz $10.00 doorbell in open space and achieved a range of 70 metres. It
may have operated for a greater distance but we could not hear the doorbell activate!
The range is reduced inside a building but you generally want to see what is happening and 30 to
50 metres is ideal.
For a greater range we have shown how to increase the distance, later in this article.

The two things you will want to do when working on 303MHz transmitters are:

1. Be able to detect 303MHz to see if a transmitter is operating,

2. Determine the output power to compare one transmitter with another.

303MHz TRANSMITTER with 32kHz Crystal

The first circuit we will investigate has a 32kHz crystal to generate a tone so the receiver does not
false-trigger.
We have already experienced a fault with a RX-3 circuit. It false triggered every 2 minutes and
pulsed the motor for 1 second. As we mentioned before, this could be due to the chip detecting a
frequency of 1kHz or 250Hz from the background noise received by the RF transistor, to turn on an
output. That's why the RX-3 receiver chip is unreliable. 32kHz is a better frequency to detect as it
does not get created from background noise.
The operation of a 303MHz circuit has been covered in our project WIRELESS DOORBELL.
We are not going over how the circuit works but explain the importance of some of the components
and how they effect the range.
The Wireless Doorbell transmitter and receiver circuit have been included below:
 The Wireless Doorbell PC board

The most critical component is the transistor.

A quality transistor is important in the RF section and Japanese transistors are by far the best for
this purpose.
The transistor used in the 303MHz oscillator has a maximum frequency of operation of 1,000MHz
and this is where its gain is equal to "1," so we want a transistor to have a good gain at 300MHz.
A BC 547 transistor will not operate at this frequency so we have used a 2N 3563 which is low
cost and will operate up to 1,000MHz. The specification sheets for these transistors:
2N3563.pdf 9018.pdf

303MHz TRANSMITTER using 4069 IC

The following circuit uses a CD 4069 IC to produce the 32kHz tone and 4 gates in parallel to turn
the oscillator transistor on and off at the tone-rate.
A single gate will not have enough output to pull the emitter to ground, however 4 gates will bring
the emitter close to 0v rail. It must not be at exactly 0v as the 6p will not have an effect in
maintaining oscillation.
The chip has 6 gates and when an input is just above mid rail, the output goes LOW. When the
input is just below mid rail the output goes HIGH. The gap between detecting a low and a high is
not very large and the gate will detect signals called "analogue signals."
But to get the oscillator circuit to start-up, a resistor is placed between output and input.
This will produce an oscillation at the highest frequency for the gate about 500kHz to 2MHz..
When another gate is added and a crystal connected between the output and the input, a "fight"
takes place between the signal produced by the 1M and the frequency delivered by the crystal.
Since the crystal has a lower impedance than the 1M, it delivers a larger signal to input pin 11 and
the two gates operate at the frequency of the crystal.
The exact nature of how the signal from the crystal overtakes the signal fed back from the 1M
resistor is not important however if you can consider the first gate starts to increase in frequency
from zero, when the signal gets to 32kHz, it starts to activate the crystal and this signal appears on
the other side and into the input pin of the first gate.
Both transmitters produce the same result, a 303MHz carrier with a 32kHz modulation (tone -
although we cannot hear this frequency). Both have the same range.

The oscillator coil is also the radiator of the signal and the 1.5uH inductor on the "centre tap" of the
coil can be as high as 10uH or as low as 1.5uH, with little difference in output.
The frequency may have to be adjusted slightly if the inductor is changed.
We changed it for a 40 turn air-would coil using .25mm wire on a 2mm former. This increased the
range by 1 metre.
A 60 turn coil increased the range a further 3 metres and when it was spread out it added to the
effect of the antenna. The two photos below show the placement of these air-inductors.

40 turn coil replacing the 1.5uH inductor

 60 turn coil spread out to increase the range of the transmitter

303MHz RECEIVER
This circuit is almost identical to the Wireless Doorbell article, only the pin numbering has been
changed to suit the layout on the PC board. I suppose, when you are onto a good circuit, stick to it!
This doorbell cost less than $8.00 and you cannot buy the components individually for less than
that.
This type of circuit makes an ideal basis for experimentation. You can experiment with the RF side
of the circuit as well as the high impedance sections. Each gate is capable of providing a very high
gain and by putting a 1M from output to input the gate is kept in a state of excitement, oscillating at
approx 500kHz, if no other components surround the gate to control the frequency. This is designed
to keep the gate active so that the smallest signal will be processed.
In the case of the gate between pins 13 and 12, the 1n capacitor between the input and ground will
reduce the frequency enormously, as well as the effect of the 2n2 and 5k6 resistor.
The second and third gates simply increase the amplitude of the signal and do not provide any form
of removal of unwanted signals.
The end result is a full amplitude signal at the left-side of the crystal with all sorts of hash and
background noise, but unless the signal has a 32kHz component, it will not start to oscillate and the
right side will have no signal. The crystal is the component that does most of the "detection work"
and prevents false triggering as it magically picks out the 32kHz signal from the "hash" and delivers
a very clean signal to the transistor for further amplification.
This signal is amplified further to full rail and charges an electrolytic to activate a sound chip.
Receiver circuit topside with sound module
 Receiver circuit underside

DETECTING OUTPUT POWER

The output of a 303MHz transmitter can be detected using Field Strength Meter MkII from Talking
Electronics.
It needs to be modified to detect this frequency.
The 47p in series with the 4 - 40p air trimmer is replaced with 10p.
The PC coil on the board is cut as shown (to remove it from circuit).
A loop of tinned copper wire is fitted from the negative rail to the 10p land on the board.
This loop now becomes the "pick-up" for the signal and the 47p is turned until the LEDs illuminate
to a maximum.
 Modifying Field Strength Meter MkII

Since none of the transmitters have the frequency set via a crystal, you will need to use a
transmitter with a known frequency to calibrate the Field Strength Meter. Once this is done you can
use it to check the frequency and output of other transmitters.
Place the loop near the transmitter and adjust the air trimmer for a maximum.
The position of the pointer will indicate if the transmitter is near the required frequency.

FIELD TESTING
Since the range of these transmitters is fairly short, the only real way to set the exact frequency is to
do a "field test."
Take the transmitter say 20 metres and press the transmit button. Keep moving away and
remember the maximum range.
Adjust the coil on the receiver and re-test. If the range increases, you are peaking the coil in the
right direction. If the range decreases, turn the slug in the opposite direction.
It will take only a few degrees of adjustment to peak the receiving frequency.
In this way you can compare one transmitter with another.