RTHD SVX01G en - 08302016 PDF

Installation, Operation,
and Maintenance
Optimus™ Water-Cooled Chillers

Model RTHD
SAFETY WARNING
Only qualified personnel should install and service the equipment. The installation, starting up, and servicing
of heating, ventilating, and air-conditioning equipment can be hazardous and requires specific knowledge and
training. Improperly installed, adjusted or altered equipment by an unqualified person could result in death or
serious injury. When working on the equipment, observe all precautions in the literature and on the tags,
stickers, and labels that are attached to the equipment.
August 2016 RTHD-SVX01G-EN

Introduction
Read this manual thoroughly before operating or servicing
this unit.
WARNING
Warnings, Cautions, and Notices Proper Field Wiring and Grounding
Required!
Safety advisories appear throughout this manual as
Failure to follow code could result in death or serious
required. Your personal safety and the proper operation of
injury. All field wiring MUST be performed by qualified
this machine depend upon the strict observance of these personnel. Improperly installed and grounded field
precautions. wiring poses FIRE and ELECTROCUTION hazards. To
avoid these hazards, you MUST follow requirements for
field wiring installation and grounding as described in
The three types of advisories are defined as follows: NEC and your local/state electrical codes.
Indicates a potentially hazardous

WARNING situation which, if not avoided, could
result in death or serious injury. WARNING
Indicates a potentially hazardous Personal Protective Equipment (PPE)
CAUTIONs situation which, if not avoided, could
result in minor or moderate injury. It Required!
could also be used to alert against Failure to wear proper PPE for the job being undertaken
unsafe practices. could result in death or serious injury. Technicians, in
order to protect themselves from potential electrical,
NOTICE Indicates a situation that could result in
mechanical, and chemical hazards, MUST follow
equipment or property-damage only
precautions in this manual and on the tags, stickers,
accidents.
and labels, as well as the instructions below:
Important Environmental Concerns • Before installing/servicing this unit, technicians

MUST put on all PPE required for the work being
Scientific research has shown that certain man-made undertaken (Examples; cut resistant gloves/sleeves,
chemicals can affect the earth’s naturally occurring butyl gloves, safety glasses, hard hat/bump cap, fall
stratospheric ozone layer when released to the protection, electrical PPE and arc flash clothing).
atmosphere. In particular, several of the identified ALWAYS refer to appropriate Material Safety Data
chemicals that may affect the ozone layer are refrigerants Sheets (MSDS)/Safety Data Sheets (SDS) and OSHA
that contain Chlorine, Fluorine and Carbon (CFCs) and guidelines for proper PPE.
those containing Hydrogen, Chlorine, Fluorine and
• When working with or around hazardous chemicals,
Carbon (HCFCs). Not all refrigerants containing these
ALWAYS refer to the appropriate MSDS/SDS and
compounds have the same potential impact to the
OSHA/GHS (Global Harmonized System of
environment. Trane advocates the responsible handling of
Classification and Labelling of Chemicals) guidelines
all refrigerants-including industry replacements for CFCs
for information on allowable personal exposure
such as HCFCs and HFCs.
levels, proper respiratory protection and handling
Important Responsible Refrigerant instructions.
Practices • If there is a risk of energized electrical contact, arc, or
flash, technicians MUST put on all PPE in accordance
Trane believes that responsible refrigerant practices are
with OSHA, NFPA 70E, or other country-specific
important to the environment, our customers, and the air
requirements for arc flash protection, PRIOR to
conditioning industry. All technicians who handle
servicing the unit. NEVER PERFORM ANY
refrigerants must be certified. The Federal Clean Air Act
SWITCHING, DISCONNECTING, OR VOLTAGE
(Section 608) sets forth the requirements for handling,
TESTING WITHOUT PROPER ELECTRICAL PPE AND
reclaiming, recovering and recycling of certain
ARC FLASH CLOTHING. ENSURE ELECTRICAL
refrigerants and the equipment that is used in these
METERS AND EQUIPMENT ARE PROPERLY RATED
service procedures. In addition, some states or
FOR INTENDED VOLTAGE.
municipalities may have additional requirements that
must also be adhered to for responsible management of
refrigerants. Know the applicable laws and follow them.
© 2016 Ingersoll Rand All rights reserved RTHD-SVX01G-EN

Introduction
and the required qualified personnel to operate the

necessary rigging equipment.
WARNING
Refrigerant under High Pressure! Copyright
Failure to follow instructions below could result in an
explosion which could result in death or serious injury This document and the information in it are the property of
or equipment damage. System contains oil and Trane, and may not be used or reproduced in whole or in
refrigerant under high pressure. Recover refrigerant to part without written permission. Trane reserves the right
relieve pressure before opening the system. See unit to revise this publication at any time, and to make changes
nameplate for refrigerant type. Do not use non- to its content without obligation to notify any person of
approved refrigerants, refrigerant substitutes, or such revision or change.
refrigerant additives.
Trademarks
Factory Warranty Information
All trademarks referenced in this document are the
Compliance with the following is required to preserve the trademarks of their respective owners.
factory warranty:
All Unit Installations Revision History
Startup MUST be performed by Trane, or an authorized
agent of Trane, to VALIDATE this WARRANTY. Contractor • Added 575V selection for units with optional AFD.
must provide a two-week startup notification to Trane (or • Incorporated E3G3G3 configuration.
an agent of Trane specifically authorized to perform • Updated TD7 information in controls chapter.
startup).
Additional Requirements for Units Requiring
Disassembly
When a new fully assembled chiller is shipped and
received from our Trane manufacturing location, and, for
any reason, it requires disassembly or partial disassembly
— which could include but is not limited to the evaporator,
condenser, control panel, compressor/motor, or any other
components originally attached to the fully assembled unit
— compliance with the following is required to preserve
the factory warranty:
• Trane, or an agent of Trane specifically authorized to
perform startup and warranty of Trane® products, will
perform or have direct onsite technical supervision of
the disassembly and reassembly work.
• The installing contractor must notify Trane — or an
agent of Trane specifically authorized to perform
startup and warrant of Trane® products — two weeks in
advance of the scheduled disassembly work to
coordinate the disassembly and reassembly work.
• Startup must be performed by Trane or an agent of
Trane specifically authorized to perform startup and
warranty of Trane® products as noted above.
Trane, or an agent of Trane specifically authorized to
perform startup and warranty of Trane® products, will
provide qualified personnel and standard hand tools to
perform the disassembly work at a location specified by
the contractor. The contractor shall provide the rigging
equipment such as chain falls, gantries, cranes, forklifts,
etc. necessary for the disassembly and reassembly work
RTHD-SVX01G-EN 3
Table of Contents
Model Number . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Fused-disconnect switches or circuit 
breakers. . . . . . . . . . . . . . . . . . . . . . . . . . . .40
Unit Nameplate . . . . . . . . . . . . . . . . . . . . . . . 6
Compressor Nameplate . . . . . . . . . . . . . . . . 6 Module Connections for Interconnecting 
Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
Model Number Descriptions . . . . . . . . . . . . . . 7 AFD Drive (Optional) . . . . . . . . . . . . . . . . . . .46
Unit Model Number . . . . . . . . . . . . . . . . . . . . 7 AFD Drive Installation . . . . . . . . . . . . . . . .46
Compressor Model Number . . . . . . . . . . . . 8 AFD Drive Programming . . . . . . . . . . . . . .47
General Information . . . . . . . . . . . . . . . . . . . . . 9 Communications Interface . . . . . . . . . . . . . .49
Unit Description . . . . . . . . . . . . . . . . . . . . . . . 9 LonTalk Interface (LCI-C) . . . . . . . . . . . . . .49
Pre-Installation . . . . . . . . . . . . . . . . . . . . . . . . . 14 BACnet Interface (BCI-C) . . . . . . . . . . . . . .49
Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Modbus Remote Terminal Unit Interface .49
Inspection Checklist . . . . . . . . . . . . . . . . . 14
Operating Principles . . . . . . . . . . . . . . . . . . . . .50
Loose Parts Inventory . . . . . . . . . . . . . . . 14 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50
Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Refrigeration Cycle . . . . . . . . . . . . . . . . . . . .50
Installation Requirements . . . . . . . . . . . . . . 15 Refrigeration Circuits . . . . . . . . . . . . . . . . . .50
Dimensions and Weights . . . . . . . . . . . . . . . . 16 Compressor and Motor . . . . . . . . . . . . . . . . .50
Unit Dimensions . . . . . . . . . . . . . . . . . . . . . . 16 Evaporator and Condenser . . . . . . . . . . . . .50
Unit Weights . . . . . . . . . . . . . . . . . . . . . . . . . 16 Oil Management . . . . . . . . . . . . . . . . . . . . . .51
Service Clearances . . . . . . . . . . . . . . . . . . . . 18 Unit-Mounted Starter . . . . . . . . . . . . . . . . . .51
Installation Mechanical . . . . . . . . . . . . . . . . . . 19 Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52
Location Requirements . . . . . . . . . . . . . . . . 19 UC800 Specifications . . . . . . . . . . . . . . . . . .52
Sound Considerations . . . . . . . . . . . . . . . 19 Wiring and Port Descriptions . . . . . . . . . .52
Foundation . . . . . . . . . . . . . . . . . . . . . . . . 19 Communication Interfaces . . . . . . . . . . . .53
Clearances . . . . . . . . . . . . . . . . . . . . . . . . . 19 Rotary Switches . . . . . . . . . . . . . . . . . . . . .53
Ventilation . . . . . . . . . . . . . . . . . . . . . . . . . 19 LED Description and Operation . . . . . . . .53
Water Drainage . . . . . . . . . . . . . . . . . . . . . 19 Tracer AdaptiView™ TD7 Display . . . . . . . .53
Access Restrictions . . . . . . . . . . . . . . . . . 19 Operator Interface . . . . . . . . . . . . . . . . . . .53
Rigging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Home Screen . . . . . . . . . . . . . . . . . . . . . . .54
Lifting Procedure . . . . . . . . . . . . . . . . . . . 23 Viewing Chiller Operating Modes . . . . . .54
Unit Leveling . . . . . . . . . . . . . . . . . . . . . . . 26 Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . .56
Isolation Pads . . . . . . . . . . . . . . . . . . . . . . 26 Reports . . . . . . . . . . . . . . . . . . . . . . . . . . . .57
Water Piping . . . . . . . . . . . . . . . . . . . . . . . 31 Equipment Settings . . . . . . . . . . . . . . . . .59
Freeze Protection . . . . . . . . . . . . . . . . . . . . . 37 Service Settings . . . . . . . . . . . . . . . . . . . . .61
Installation Electrical . . . . . . . . . . . . . . . . . . . . 38 Display Settings . . . . . . . . . . . . . . . . . . . .61
General Recommendations . . . . . . . . . . . . 38 Viewing the Settings Screen . . . . . . . . . .61
Electrical Data . . . . . . . . . . . . . . . . . . . . . . . . 38 Cleaning the Display . . . . . . . . . . . . . . . . .63
Standard Units with Wye-Delta Starter . 38 Security Settings . . . . . . . . . . . . . . . . . . . .63
Units with AFD Option . . . . . . . . . . . . . . . 39 Disabling/Enabling Security . . . . . . . . . . .63
Installer-Supplied Components . . . . . . . . . 39 Tracer® TU . . . . . . . . . . . . . . . . . . . . . . . . . . .65
4 RTHD-SVX01G-EN
Table of Contents
Pre-Start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 Starter Diagnostics . . . . . . . . . . . . . . . . . . . .83

Start-Up and Shutdown . . . . . . . . . . . . . . . . . 67 Main Processor Diagnostics . . . . . . . . . . . . .86
Unit Start-Up . . . . . . . . . . . . . . . . . . . . . . . . . 67 Communication Diagnostics . . . . . . . . . . . .91
Temporary Shutdown And Restart . . . . . . 67 Operator Display Diagnostics and 
Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . .93
Extended Unit Shutdown . . . . . . . . . . . . . . 67
Seasonal Unit Start-Up Procedure . . . . . . 67 Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .94
Sequence of Operation . . . . . . . . . . . . . . . . 68 Log and Check Sheets . . . . . . . . . . . . . . . . . . .95
Software Operation Overview . . . . . . . . . 68
Timelines . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Power Up . . . . . . . . . . . . . . . . . . . . . . . . . 69
Power Up to Starting . . . . . . . . . . . . . . . . 70
Stopped to Starting . . . . . . . . . . . . . . . . . 71
Starting Wye-Delta . . . . . . . . . . . . . . . . . . 71
Starting AFD . . . . . . . . . . . . . . . . . . . . . . . 72
Running . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Satisfied Setpoint . . . . . . . . . . . . . . . . . . . 73
Normal Shutdown to Stopped or 
Run Inhibit . . . . . . . . . . . . . . . . . . . . . . . . . 74
Immediate Shutdown to Stopped or 
Run Inhibit . . . . . . . . . . . . . . . . . . . . . . . . . 75
Momentary Power Loss . . . . . . . . . . . . . . 75
Ice Making (Running to Ice Making to 
Running) . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Ice Making (Auto to Ice Making to Ice 
Making Complete) . . . . . . . . . . . . . . . . . . 76
No Load Start . . . . . . . . . . . . . . . . . . . . . . 77
Limit Conditions . . . . . . . . . . . . . . . . . . . . . . 77
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Recommended Maintenance . . . . . . . . . . . 78
Weekly . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Monthly . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Annual . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Scheduling Other Maintenance . . . . . . . 78
Refrigerant and Oil Charge Management 78
Maintenance Procedures . . . . . . . . . . . . . . 79
Cleaning the Condenser . . . . . . . . . . . . . 79
Cleaning the Evaporator . . . . . . . . . . . . . 80
Oil Sump Level Check . . . . . . . . . . . . . . . 81
Optional AFD
Periodic Maintenance and Inspection . . 82
Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
RTHD-SVX01G-EN 5
Model Number
Nameplates of typical unit model number and the coding system for
each.
The Optimus™ unit nameplates are applied to the exterior Each position, or group of positions, in the model number
of the Control Panel. A compressor nameplate is located is used to represent a feature. For example, in the first
on the compressor. When the unit arrives, compare all table, position 08 of the unit model number, Unit Voltage,
nameplate data with ordering, submittal, and shipping contains the letter “F”. An F in this position means that the
information. unit voltage is 460/60/3.
Unit Model Number. An example of a typical unit
Unit Nameplate model number (M/N) is:
See Figure 1 for a typical unit nameplate. The unit RTHD UB1F XG0U AB1A 2LAL B1A2 LALA VXQX EXAA
nameplate provides the following information: AXY1 76DC XT52 XXXX XXH
• Unit model and size description. Model number digits are selected and assigned in
• Unit serial number. accordance with the definitions as listed in “Unit Model
Number,” p. 7.
• Identifies unit electrical requirements.
• Lists correct operating charges of R-134a and Compressor Nameplate
refrigerant oil.
• Lists unit test pressures. The compressor nameplate provides the following
information:
• Identifies installation, operation and maintenance and
service data literature. • Compressor model number. See “Compressor Model
Number,” p. 8.
• Lists drawing numbers for unit wiring diagrams.
• Compressor electrical characteristics.
Model Number Coding System • Utilization range.
The model numbers for the unit and the compressor are • Recommended refrigerant.
composed of numbers and letters that represent features
of the equipment. Shown in the following table is a sample
Figure 1. Typical unit nameplate
6 RTHD-SVX01G-EN
Model Number Descriptions
Unit Model Number
Digits 1 - 4 – Chiller Model Digits 14,15 – Evaporator Digit 24 – Condenser Water
RTHD= Water-Cooled Optimus™ Chiller B1 = B1 Evaporator Passes
B2 = B2 Evaporator 2 = 2 Pass
Digit 5 – Manufacturing C1 = C1 Evaporator
Location C2 = C2 Evaporator Digit 25 – Condenser Water
U = Water Chiller Business Unit,  D1 = D1 Evaporator Connection
Pueblo, CO USA D2 = D2 Evaporator L = Left Hand
D3 = D3 Evaporator R = Right Hand
Digits 6, 7 – Compressor Frame D4 = D4 Evaporator
B1 = B1 Compressor D5 = D5 Evaporator Digit 26 – Condenser
B2 = B2 Compressor D6 = D6 Evaporator Connection Type
C1 = C1 Compressor E1 = E1 Evaporator A = Standard Grooved Pipe
C2 = C2 Compressor F1 = F1 Evaporator C = Marine
D1 = D1 Compressor F2 = F2 Evaporator S = Special
D2 = D2 Compressor G1 = G1 Evaporator
D3 = D3 Compressor (50 hz only) G2 = G2 Evaporator Digit 27 – Condenser Waterside
E3 = E3 Compressor (50 hz only) G3 = G3 Evaporator Pressure
Digits 8 – Unit Power Supply Digit 16 – Evaporator Tube Type L = 150 psi (10.5 bar)
A = 200V/60Hz/3Ph power H = 300 psi (21 bar)
A = Enhanced fin copper (all fluids)
C = 230V/60Hz/3Ph power W = Enhanced fin copper (water only) Digit 28 – Condenser Leaving
D = 380V/60Hz/3Ph power Water Temperature
F = 460V/60Hz/3Ph power Digit 17 – Evaporator Water Pass
H = 575V/60Hz/3Ph power Configuration A = Standard
R = 380V/50Hz/3Ph power 2 = 2 Pass Digit 29 – Refrigerant Isolation
T = 400V/50Hz/3Ph power 3 = 3 Pass Valves
U = 415V/50Hz/3Ph power 4 = 4 Pass
X = No Refrigerant Isolation Valves
Digit 9 – Specials Digit 18 – Evaporator Water V = With Refrigerant Isolation Valves
X = No Specials Connection Digit 30 – Oil Cooler
Historical information: L = Left Hand
C = Specials denoted elsewhere X = Without Oil Cooler
R = Right Hand C = With Oil Cooler
S = Specials not denoted elsewhere
Digit 19 – Evaporator Digit 31 – Thermal Insulation
Digit 10, 11 – Design Sequence
Connection Type X = No Insulation
** = Factory assigned
A = Standard Grooved Pipe Q = Factory Installed Insulation
Digit 12 – Agency Listing Historical information:
S = Special
Digit 32 – Acoustic Insulation
X = No Agency Listing
U = UL Listed to US and Canadian X = No Insulation
Digit 20 – Evaporator Water Historical information:
Safety Standard
A = IBC Seismically Rated Side Pressure A = Standard Attenuator
B = UL/Canadian and IBC L = 150 psi (10.5 bar) Digit 33 – Label and Literature
C = OSHPD Seismically Rated H = 300 psi (21 bar)
Language
D = UL/Canadian and OSHPD Digit 21, 22 – Condenser
Historical information: C = Spanish
3 = CCC - Chinese Compulsory Code B1 = B1 Condenser E = English
B2 = B2 Condenser F = French
Note: Digit 12 selections A, B, C & D are D1 = D1 Condenser
special order only. D2 = D2 Condenser
Digit 34 – Safety Devices
Digit 13 – Pressure Vessel Code E1 = E1 Condenser X = Standard
E2 = E2 Condenser Digit 35 – Factory Charge
A = ASME Pressure Vessel Code
E3 = E3 Condenser
C = Canadian Code A = Factory Refrigerant Charge
E4 = E4 Condenser
D = Australian Code (R-134a)
E5 = E5 Condenser
L = Chinese Code-Imported Pressure B = Factory Nitrogen Charge
F1 = F1 Condenser
Vessel
Historical information:
F2 = F2 Condenser Digit 36 – Shipping Package
F3 = F3 Condenser A = No Skid (Standard)
S = Special
G1 = G1 Condenser B = Shrink Wrap
G2 = G2 Condenser C = Skid
G3 = G3 Condenser D = Skid + Shrink Wrap
Digit 23 – Condenser Tube Type Historical information:
J = Special
A = Enhanced Fin Copper - 0.028”
B = Smooth Bore Copper
C = Smooth Bore CuNi
D = Enhanced Fin Copper - 0.025”
RTHD-SVX01G-EN 7
Model Number Descriptions
Digit 37 – Flow Switch Digit 45 – Under/Over Voltage Digits 54 – Refrigerant Monitor

X = No Flow Switch Protection Input
A = Evaporator (NEMA 1) X = None X = None
B = Evaporator and Condenser U = With Under/Over Voltage A = 100 ppm / 4-20 mA
(NEMA 1) Protection B = 1000 ppm / 4-20 mA
C = Evaporator (NEMA 4) C = 100 ppm / 2-10 Vdc
D = Evaporator and Condenser Digit 46 – Operator Interface D = 1000 ppm / 2-10 Vdc
(NEMA 4) T = Tracer AdaptiView™ TD7 Display
Historical information: Digit 55 – Condenser Leaving
Digit 38 – Factory Test A = DynaView™ - English Hot Water Temp Control
X = Standard Test B = DynaView - French X = None
C = Witness Test C = DynaView - Italian H = Hot Water Temp Control
D = Performance Test D = DynaView - Spanish
E = DynaView - German Digits 56 - 58 — AFD Output
Digit 39 – Starter Type
F = DynaView - Dutch Amps
Y = Wye-Delta Closed Transition G = DynaView - Chinese
Starter 000 = Not applicable (wye-delta starter)
(traditional) *** = Selection Assigned
V = Premium AFD H = DynaView - Chinese (simple)
Historical information: J = DynaView - Japanese
A = Solid State Starter K = DynaView - Portugese (Brazil) Compressor Model
Digits 40 - 42 — Design RLA L = DynaView - Korean
(for starter) M = DynaView - Thai Number
*** = Selection Assigned Digit 47 – Digital
Digits 1 - 4— Compressor Model
Digit 43 – Power Line Communication Interface
CHHC= Positive displacement, 
Connection Type X = None helical rotary (twin screw)
5 = LCI-C (LonTalk®) Interface hermetic compressor
A = Terminal Block 7 = BACnet®
B = Mechanical Disconnect Switch 8 = Modbus™ Interface Digit 5— Design Control
D = Circuit Breaker
Historical information: * = Factory Assigned
F = High Interrupt Circuit Breaker
4 = Tracer® Comm 4 Interface
Historical information:
6 = BACnet® for CH530 Controls Digit 6— Frame Size
H = Ground Fault Circuit Breaker B = B Frame
J = Ground Fault High Interrupt Digit 48 – External Water & C = C Frame
Circuit Breaker Current-Limit Setpoint D = D Frame
Digit 44 – Max RLA (Starter) X = None E = E Frame
C = 277 max RLA (Fixed Speed) 2 = 2–10 Vdc input Digit 7— Capacity
E = 364 max RLA (Fixed Speed) 4 = 4–20 mA input
1 = Smaller capacity (minor)
G = 126 max RLA (Drive and Panel) Digit 49 – External Base Loading 2 = Larger capacity (major)
H = 150 max RLA (Drive and Panel) 3 = Special 50 Hz
J = 185 max RLA (Drive and Panel) X = None
K = 234 max RLA (Drive and Panel) 2 = 2–10 Vdc input Digit 8 — Motor Voltage
L = 279 max RLA (Drive and Panel) 4 = 4–20 mA input
A = 200V/60Hz/3Ph
M = 316 max RLA (Drive and Panel) Digit 50 – Ice Making C = 230V/60Hz/3Ph
N = 366 max RLA (Drive and Panel) X = None D = 380V/60Hz/3Ph
Q = 397 max RLA (Fixed Speed) A = Ice Making with Relay F = 400/460V- 50/60Hz - 3Ph
R = 476 max RLA (Fixed Speed) B = Ice Making without Relay used for 380V/50Hz/3Ph
T = 598 max RLA (Fixed Speed) H = 575V/60Hz/3Ph
U = 779 max RLA (Fixed Speed) Digit 51 – Programmable Relays M = 690V/50Hz/3Ph
V = 197 max RLA (Drive and Panel) X = None B = 525V/50Hz/3Ph
W = 241 max RLA (Drive and Panel) R = With Programmable Relays G = 500V/50Hz/3Ph
X = 292 max RLA (Drive and Panel) S = Special voltage
Y = 367 max RLA (Drive and Panel) Digit 52 – Chilled Water Reset
Z = 446 max RLA (Drive and Panel) X = Chilled Water Reset - Digit 9— Design Specials
1 = 549 max RLA (Drive and Panel) Return Water 0 = No specials
2 = 176 max RLA (Drive and Panel) T = Chilled Water Reset -  C = All specials denoted by digits
3 = 223 max RLA (Drive and Panel) Outdoor Air Temperature elsewhere
4 = 280 max RLA (Drive and Panel) S = Uncategorized special not
Digit 53 – Control Outputs denoted by other digits
5 = 335 max RLA (Drive and Panel)
6 = 411 max RLA (Drive and Panel) X = None
D = Chiller Differential Pressure & Digits 10 - 11— Design
7 = 455 max RLA (Drive and Panel)
Historical information - Enclosure Type: Percent RLA Sequence
F = NEMA 1 - MRLA207 P = Condenser Pressure (% HPC) & ** = Factory assigned
G = NEMA 1 - MRLA277 Percent RLA
H = NEMA 1 - MRLA300 V = Condenser Regulating Valve
J = NEMA 1 - MRLA364 Control & Percent RLA
K = NEMA 1 - MRLA397
L = NEMA 1 - MRLA476
M = NEMA 1 - MRLA500
N = NEMA 1 - MRLA598
P = NEMA 1 - MRLA779
8 RTHD-SVX01G-EN
General Information
Unit Description
The RTHD units are single compressor, helical-rotary type, Figure 2 through Figure 4 show typical Optimus™ units
water-cooled liquid chillers designed for installation and their components. Water inlet and outlet openings are
indoors. Each unit is a completely assembled, hermetic covered before shipment. The oil tank is factory charged
package that is factory-piped, wired, leak-tested, with the proper amount of refrigeration oil. The unit can be
dehydrated, charged (optional), and tested for proper factory charged with refrigerant.
control operation before shipment.
Figure 2. Component location — Optimus™ wye-delta starter (front view)
TD7 Interface
Control Panel Oil Separator
Relief Valves
Oil Sump
Condenser
Evaporator Water Outlet
Liquid Level
Sensor
Gas Pump Condenser

Evaporator
Water Outlet Water Inlet
Figure 3. Component location — Optimus™ with AFD (front view)(a)

AFD
(a) Component locations shown in Figure 2 are the same for units with optional AFD.
RTHD-SVX01G-EN 9
General Information
Figure 4. Component location — Optimus (back view)(a)
Oil Separators Compressor

Oil Filter (Cold)
Hot Oil Filter is
hidden from view. Discharge Line
Unit Nameplate
Relief Valves (On side of starter/control panel)
EXVs
Evaporator
Water Inlet
Condenser
Service Valves Oil Sump
(With Refrigerant Isolation (The oil distribution system is located between
Valve Option Only) the condenser and the evaporator.)
(a) Optional AFD is not shown. See Figure 3, p. 9 for location of optional AFD.
10 RTHD-SVX01G-EN
General Information
Table 1. General data

Unit Configuration(a) B1B1B1 B1C1D1 B2B2B2 B2C2D2 C1D5E4 C1D6E5 C1E1F1 C2D3E3
GENERAL
Refrigerant Type HFC-134a
Refrigerant Charge lb 410 490 410 490 490 490 525 490
kg 186 222 186 222 222 222 238 222
Oil Type (wye-delta) OIL48
Oil Charge(b) (wye-delta) gal 4.5 4.5 4.5 4.5 6 6 10 6
L 17 17 17 17 23 23 38 23
Oil Type (AFD) OIL315
Oil Charge (AFD) gal 7.5 7.5 7.5 7.5 10 10 11 10
L 28.5 28.5 28.5 28.5 38 38 42 38
EVAPORATOR
Water Storage gal 41 55 45 58 52 45 82 78
L 155 208 170 220 197 170 310 295
Connection size in 8 8 8 8 8 8 8 8
mm 200 200 200 200 200 200 200 200
Min Flow - Water gpm 253 320 288 347 351 293 450 486
l/s 16 18 22 22 21 18 28 31
2-pass
Min Flow - Freeze Inhibitor gpm 303 346 346 375 422 352 487 584
l/s 19 22 22 24 27 22 31 37
Maximum Flow gpm 1104 1412 1266 1531 1542 1287 1980 2131
l/s 70 89 80 97 97 81 125 134
mm 150 150 150 150 200 200 200 200
l/s 11 13 12 15 15 12 19 20
3-pass
l/s 13 16 15 17 18 15 23 25
Maximum Flow gpm 736 941 844 1022 1028 860 1320 1417
l/s 46 59 53 65 65 54 83 89
CONDENSER (all are 2-pass)
mm 150 150 150 150 200 200 200 200
L 106 117 110 129 121 110 226 178
l/s 12 12 13 13 15 13 24 21
l/s 15 15 16 16 19 16 28 25
Max Flow gpm 850 850 935 935 1080 910 1650 1420
l/s 54 54 59 59 68 57 104 90
(a) Unit configuration digits 1, 2 - compressor code (also shown in unit model number digits 6, 7); digits 3, 4 - evaporator code (unit model number digits
14, 15); digits 5, 6 - condenser code (unit model number digits 21, 22).
(b) If oil cooler is installed, add 0.3 gal (1L) to oil charge value given for B compressor family units. Add 1.0 gal (4L) for all other units.
RTHD-SVX01G-EN 11
General Information

Unit Configuration(a) C2D4E4 C2F2F3 D1D1E1 D1F1F2 D1G1G1 D1G2G2 D2D2E2 D2F2F3
GENERAL
Refrigerant Charge lb 490 625 475 625 700 700 475 625
kg 222 284 216 284 318 318 216 284
Oil Charge(b) (wye-delta) gal 6 10 6 10 11 11 6 10
L 23 38 23 38 42 42 23 38
Oil Charge (AFD) gal 10 12 9.5 11 13.5 13.5 9.5 11
L 38 45.5 36 42 51 51 36 42
EVAPORATOR
L 197 405 261 386 515 545 280 405
Connection size in 8 10 8 10 - - 8 10
mm 200 250 200 250 - - 200 250
Min Flow - Water gpm 351 604 415 563 - - 450 604
l/s 21 38 26 36 - - 28 38
2-pass
Min Flow - Freeze Inhibitor gpm 422 725 498 676 - - 541 725
l/s 27 46 31 43 - - 34 46
Maximum Flow gpm 1542 2667 1812 2478 - - 1980 2667
l/s 97 168 114 156 - - 125 168
mm 200 200 200 200 250 250 200 200
l/s 15 25 17 24 35 35 19 25
3-pass
l/s 18 31 21 29 38 42 23 31
Maximum Flow gpm 1028 1780 1206 1655 2218 2413 1320 1780
l/s 65 112 76 104 140 152 83 112
Connection size in - - - - 8 8 - -
mm - - - - 200 200 - -
Min Flow - Water gpm - - - - 379 411 - -
l/s - - - - 24 26 - -
4-pass
Min Flow - Freeze Inhibitor gpm - - - - 454 492 - -
l/s - - - - 29 31 - -
Maximum Flow gpm - - - - 1666 1807 - -
l/s - - - 105 114 - -
mm 200 200 200 200 200 200 200 200
L 121 231 166 216 299 344 178 231
l/s 15 22 18 22 28 34 20 24
l/s 19 29 22 27 33 41 24 29
Max Flow gpm 1080 1700 1280 1560 1960 2360 1390 1700
l/s 68 107 81 98 124 149 88 107
(a) Unit configuration digits 1, 2 - compressor code (also shown in unit model number digits 6, 7); digits 3, 4 - evaporator code (unit model number digits
14, 15); digits 5, 6 - condenser code (unit model number digits 21, 22).
12 RTHD-SVX01G-EN
General Information

Unit Configuration(a) D2G2G1 D2G3G3 D3D2E2 D3F2F3 D3G2G1 E3D2E2 E3F2F3 E3G2G1 E3G3G3
GENERAL
Refrigerant Charge lb 700 700 475 625 700 475 625 700 700
kg 318 318 216 284 318 216 284 318 318
Oil Charge(b) (wye-delta) gal 11 11 6 10 11 6 10 11 11
L 42 42 23 38 42 23 38 42 42
Oil Charge (AFD) gal 13.5 13.5 9.5 11 13.5 9.5 11 13.5 13.5
L 51 51 36 42 51 36 42 51 51
EVAPORATOR
Water Storage gal 144 159 74 107 144 74 107 144 159
L 545 602 280 405 545 280 405 545 602
2-pass Connection size in - - 8 10 - 8 10 - -
mm - - 200 250 - 200 250 - -
Min Flow - Water gpm - - 450 604 - 450 604 - -
l/s - - 28 38 - 28 38 - -
Min Flow - Freeze Inhibitor gpm - - 541 725 - 541 725 - -
l/s - - 34 46 - 34 46 - -
Maximum Flow gpm - - 1980 2667 - 1980 2667 - -
l/s - - 125 168 - 125 168 - -
3-pass Connection size in 10 10 8 8 10 8 8 10 10
mm 250 250 200 200 250 200 200 250 250
Min Flow - Water gpm 550 622 300 404 550 300 404 550 622
l/s 35 39 19 25 35 19 25 35 39
Min Flow - Freeze Inhibitor gpm 660 747 357 487 660 357 487 660 747
l/s 42 47 23 31 42 23 31 42 47
Maximum Flow gpm 2413 2732 1320 1780 2413 1320 1780 2413 2732
l/s 152 172 83 112 152 83 112 152 172
4-pass Connection size in 8 8 - - 8 - - 8 8
mm 200 200 - - 200 - - 200 200
Min Flow - Water gpm 411 466 - - 411 - - 411 466
l/s 26 29 - - 26 - - 26 29
Min Flow - Freeze Inhibitor gpm 492 557 - - 492 - - 492 557
l/s 31 35 - - 31 - - 31 35
Maximum Flow gpm 1807 2050 - - 1807 - - 1807 2050
l/s 114 129 - - 114 - - 114 129
Connection size in 8 8 8 8 8 8 8 8 8
mm 200 200 200 200 200 200 200 200 200
Water Storage gal 79 97 47 61 79 47 61 79 97
L 299 367 178 231 299 178 231 299 367
Min Flow - Water gpm 444 589 316 385 444 316 385 444 589
l/s 28 37 20 24 28 20 24 28 37
Min Flow - Freeze Inhibitor gpm 530 710 380 460 530 380 460 530 710
l/s 33 45 24 29 33 24 29 33 45
Max Flow gpm 1960 2600 1390 1700 1960 1390 1700 1960 2600
l/s 124 164 88 107 124 88 107 124 164
(a) Unit configuration digits 1, 2 - compressor code (also shown in unit model number digits 6, 7); digits 3, 4 - evaporator code (unit model number digits 14, 15); digits 5, 6 - condenser
code (unit model number digits 21, 22).
RTHD-SVX01G-EN 13
Pre-Installation
Inspection
When the unit is delivered, verify that it is the correct unit 46 psig at 50oF), call a qualified service organization
and that it is properly equipped. and the appropriate Trane sales office.
Inspect all exterior components for visible damage. Report Note: Pressure will be approximately 20 psig if shipped
any apparent damage or material shortage to the carrier with the optional nitrogen charge.
and make a “unit damage” notation on the carrier’s
delivery receipt. Specify the extent and type of damage
found and notify the appropriate Trane Sales Office.
Do not proceed with installation of a damaged unit without
sales office approval.
Inspection Checklist
To protect against loss due to damage incurred in transit,
complete the following checklist upon receipt of the unit.
• Inspect the individual pieces of the shipment before
accepting the unit. Check for obvious damage to the
unit or packing material.
• Inspect the unit for concealed damage as soon as
possible after delivery and before it is stored.
Concealed damage must be reported within 10 days
after receipt.
• If concealed damage is discovered, stop unpacking the
shipment. Do not remove damaged material from the
receiving location. Take photos of the damage, if
possible. The owner must provide reasonable
evidence that the damage did not occur after delivery.
• Notify the carrier’s terminal of the damage
immediately, by phone and by mail. Request an
immediate, joint inspection of the damage with the
carrier and the consignee.
• Notify the Trane sales representative and arrange for
repair. Do not repair the unit, however, until damage is
inspected by the transportation representative.
Loose Parts Inventory

Check all items against the shipping list. Water vessel drain
plugs, isolation pads, rigging and electrical diagrams,
service literature and the starter/control panel wire pullbox
(required on some starters) are shipped loose in the
control panel.
Storage
If the chiller is to be stored more than one month prior to
installation, observe the following precautions:
• Do not remove the protective coverings from the
electrical panel.
• Store the chiller in a dry, secure area.
• At least every three months, attach a gauge and
manually check the pressure in the refrigerant circuit.
If the refrigerant pressure is below 71 psig at 70oF (or
14 RTHD-SVX01G-EN
Pre-Installation
Installation Requirements
A list of the contractor responsibilities typically associate
with the unit installation process is provided in Table 4.
Table 4. Installation requirements

Trane Supplied,  Trane Supplied,  Field Supplied, 
Requirement Trane Installed Field Installed Field Installed
• Safety chains
Rigging
• Clevis connectors - Lifting beam
• Trane, or an agent 
Disassembly/ of Trane specifically authorized to perform
Reassembly start-up of Trane® products (contact 
(as required)(a) your local Trane 
office for pricing)
Isolation • Isolation pads • Isolation pads
• Circuit breakers or non-fused disconnects • Circuit breaker or non-fused disconnect • Circuit breakers or fusible disconnects
(optional) handle (optional)
• Unit-mounted starter • Temperature sensor (optional outdoor air) • Terminal lugs
• Flow switches (may be field-supplied) • Ground connection(s)
• Condenser water regulating valve • Jumper bars
controller (optional: may be field- • BAS wiring (optional)
Electrical supplied) • IPC wiring
• Control voltage wiring
• High condenser pressure interlock wiring
• Chilled water pump contactor and wiring
• Condenser water pump contactor and
wiring
• Optional relays and wiring
• Flow switches (may be field-supplied) • Thermometers
• Condenser water regulating valve • Water flow pressure gauges
controller  • Isolation and balancing valves in water
Water piping (optional- may be field-supplied) piping
• Vents and drain valves
• Pressure relief valves 
(for water boxes as required)
Pressure Relief • Relief valves Vent line and flexible connector
Insulation • Insulation (optional) Insulation
Optimus™ RTHD
Installation 
Completion Check Sheet
and Request 
for Trane Service
(RLC-ADF005*-EN, 
see “Log and Check
Sheets,” p. 95)
• Trane, or an agent of 
Chiller Start-up
Trane specifically authorized to
Commissioning(b)
perform start-up of Trane® products
(a) Trane, or an agent of Trane specifically authorized to perform start-up and warranty of Trane® products, will perform or have direct on-site supervision of
the disassembly and reassembly work.
(b) Start-up must be performed by Trane or an agent of Trane specifically authorized to perform start-up and warranty of Trane® products. Contractor shall
provide Trane (or an agent of Trane specifically authorized to perform start-up) with notice of the scheduled start-up at least two weeks prior to the scheduled
start-up.
RTHD-SVX01G-EN 15
Dimensions and Weights
Unit Dimensions
See unit submittals for specific unit dimensions and water
connection locations.
Unit Weights
Table 5. Weights — standard units (wye-delta starter)
Shipping Weight Operating Weight

Unit Configuration(a) lbs kg lbs kg
B1B1B1 9,292 4,215 9,867 4,476
B1C1D1 9,837 4,462 10,554 4,787
B2B2B2 9,402 4,265 10,019 4,545
B2C2D2 9,953 4,515 10,653 4,832
C1D5E4 12,973 5,884 13,673 6,202
C1D6E5 12,780 5,797 13,397 6,077
C1E1F1 14,718 6,676 15,818 7,175
C2D3E3 14,002 6,351 15,044 6,824
C2D4E4 12,972 5,884 13,672 6,201
C2F2F3 16,168 7,334 17,560 7,965
D1D1E1 14,443 6,551 15,385 6,987
D1F1F2 16,187 7,342 17,537 7,955
D1G1G1 18,600 8,437 20,500 9,299
D1G2G2 19,107 8,667 21,065 9,555
D2D2E2 14,562 6,605 15,570 7,062
D2F2F3 16,820 7,629 18,220 8,264
D2G2G1 18,700 8,482 20,700 9,389
D2G3G3 19,508 8,849 21,641 9,816
D3D2E2 14,562 6,605 15,570 7,062
D3F2F3 16,820 7,629 18,220 8,264
D3G2G1 18,650 8,460 20,650 9,367
E3D2E2 14,720 6,677 15,728 7,134
E3F2F3 16,956 7,691 18,356 8,326
E3G2G1 18,800 8,528 20,800 9,435
E3G3G3 19,653 8,915 21,786 9,882
Notes:
1. All weights +/- 3%
2. Shipping weights include standard 150 psig water boxes, refrigerant charge and oil charge.
3. Operating weights include refrigerant, oil and water charges.
(a) Unit configuration digits 1, 2 - compressor code (also shown in unit model number digits 6, 7); digits 3, 4 - evaporator code (unit
model number digits 14, 15); digits 5, 6 - condenser code (unit model number digits 21, 22).
16 RTHD-SVX01G-EN
Table 6. Weights — units with AFD option(a)
Shipping Weight Operating Weight

AFD D1H Frame AFD D2H Frame AFD D1H Frame AFD D2H Frame
Unit
Configuration(b) lbs kg lbs kg lbs kg lbs kg
B1B1B1 9526 4321 9664 4384 10101 4582 10239 4645
B1C1D1 10071 4568 10209 4631 10787 4893 10925 4956
B2B2B2 9636 4371 9774 4434 10251 4650 10389 4713
B2C2D2 10187 4621 10325 4684 10886 4938 11024 5001
C1D5E4 13206 5990 13344 6053 13904 6307 14043 6370
C1D6E5 13014 5903 13153 5966 13631 6183 13770 6246
C1E1F1 14949 6781 15088 6844 16801 7621 16940 7684
C2D3E3 14235 6457 14374 6520 15278 6930 15417 6993
C2D4E4 13206 5990 13344 6053 13907 6308 14046 6371
C2F2F3 17055 7736 17194 7799 18446 8367 18585 8430
D1D1E1 - - 14815 6720 - - 15756 7147
D1F1F2 - - 16559 7511 - - 17910 8124
D1G1G1 - - 18973 8606 - - 20873 9468
D1G2G2 - - 19480 8836 - - 21438 9724
D2D2E2 - - 14934 6774 - - 15944 7232
D2F2F3 - - 17194 7799 - - 18594 8434
D2G2G1 - - 19072 8651 - - 21074 9559
D2G3G3 - - 19881 9018 - - 22013 9985
D3D2E2 - - 14934 6774 - - 15944 7232
D3F2F3 - - 17194 7799 - - 18594 8434
D3G2G1 - - 19023 8629 - - 21023 9536
E3D2E2 - - 15093 6846 - - 16100 7303
E3F2F3 - - 17337 7864 - - 18728 8495
E3G2G1 - - 19173 8697 - - 21173 9604
E3G3G3 20036 9088 22169 10056
Notes:
1. All weights +/- 3%
2. Shipping weights include standard 150 psig water boxes, refrigerant charge and oil charge.
3. Operating weights include refrigerant, oil and water charges.
4. AFD frame size determined by unit selection. See submittal for information.
(a) Weights vary with AFD frame size. D1H frame size used on units with model number digit 44 = G, H, J, V, W, X, 2, 3, or 4. D2H frame size
used with model number digit 44 = K, L, M, N, Y, Z, 1, 5, 6, or 7.
(b) Unit configuration digits 1, 2 - compressor code (also shown in unit model number digits 6, 7); digits 3, 4 - evaporator code (unit model number
digits 14, 15); digits 5, 6 - condenser code (unit model number digits 21, 22).
RTHD-SVX01G-EN 17
Service Clearances
Notes:
• Required vertical clearance above unit is 36” (914 mm). • If the room configuration requires a variance to the
There should be no piping or conduit located over the clearance dimensions, contact your Trane sales office
compressor motor. representative.
• Maximum clearances are given. Some units
configurations may require less clearance than others
in the same category.
Figure 5. Service clearances(a)

3’-0” (914 mm)
Service Clearance 3’-0” (914mm)
Service Clearance
Tube Removal
Clearance
(Either End)
3’-0” (914mm)
EDE, DDE, CDE, BBB: Service Clearance
108” (2743mm) (Opposite
Tube Removal)
EFF, DFF, CEF, BCD:
126” (3200mm)
EGG, DGG, CGG:

130” (3302mm) 36.5” (927mm) 26.4” (671mm) 3’-0”
Radius Radius (914mm)
105° Swing Service
Clearance
TOP VIEW END VIEW
(a) Optional AFD is not shown. See Figure 3, p. 13 for location of optional AFD.
18 RTHD-SVX01G-EN
Installation Mechanical
Location Requirements Ventilation must be adequate to maintain an ambient
temperature lower than the following:
Sound Considerations Wye-Delta Starter Units: 104°F (40°C)
Note: See Trane Engineering Bulletin Sound Ratings and AFD Unit Option: 104°F (40°C)
Installation Guide Optimus™ Water-Cooled

Chillers RLC-PRB015*-EN for sound consideration Vent the evaporator, condenser and compressor pressure
applications. relief valves in accordance with all local and national
codes. See Table 10, p. 35
• Locate the unit away from sound-sensitive areas.
Make provisions in the equipment room to keep the chiller
• Install the isolation pads under the unit. Refer to “Unit from being exposed to freezing temperatures (32oF/0oC).
Isolation.”
• Install rubber vibration isolators in all water piping. Water Drainage
• Isolate all pipe hangers and be sure they are not Locate the unit near a large capacity drain for water vessel
supported by main structure beams that could drain-down during shutdown or repair. Condensers and
introduce vibration into occupied spaces. evaporators are provided with drain connections. See “,”
• Make sure that the piping does not put additional p. 32. All local and national codes apply.
stress on the unit.
Access Restrictions
Note: Do not use metal braided type eliminators on the
water piping. Metal braided eliminators are not Door clearances are given in Figure 5, p. 18. See unit
effective at the frequencies at which the unit will submittals for specific “per unit” dimensional
operate. information.
• Use flexible electrical conduit.

Rigging
• Seal all wall penetrations.
Note: Consult an acoustical engineer for critical Important: If unit must be disassembled for
applications. installation, see Engineering Bulletin RTHD-
SVB02*-EN, Disassembly Procedure,
Foundation Optimus™ Water-Cooled Chillers, for
instructions, including weights and rigging
Provide rigid, non-warping mounting pads or a concrete instruction for components.
foundation of sufficient strength and mass to support the
chiller operating weight (including completed piping and The Optimus™ chiller should be moved by lifting at
full operating charges of refrigerant, oil and water). See designated lift points only. See Table 5, p. 16 and Table 6,
Table 5, p. 16 or Table 6, p. 17 for unit operating weights. p. 17 for overall unit weights. See Figure 6, p. 20 and
Table 7, p. 20 for typical unit lifting point weights.
Place the manufacturer-supplied isolation pad assemblies
under the unit. Once in place, level the chiller within 1/4”
(6.35 mm) over its length and width.
WARNING
The Trane Company is not responsible for equipment
problems resulting from an improperly designed or Heavy Objects!
constructed foundation. Failure to follow instructions below or properly lift unit
could result in unit dropping and possibly crushing
Clearances operator/technician which could result in death or
serious injury, and equipment or property-only damage.
Provide enough space around the unit to allow the Ensure that all the lifting equipment used is properly
installation and maintenance personnel unrestricted rated for the weight of the unit being lifted. Each of the
access to all service points. Refer to submittal drawings for cables (chains or slings), hooks, and shackles used to
the unit dimensions. lift the unit must be capable of supporting the entire
weight of the unit. Lifting cables (chains or slings) may
See Figure 5, p. 18 for minimum clearances required for not be of the same length. Adjust as necessary for even
service. In all cases, local codes will take precedence over unit lift.
these recommendations.
Ventilation
The unit produces heat even though the compressor is
cooled by the refrigerant. Make provisions to remove heat
generated by unit operation from the equipment room.
RTHD-SVX01G-EN 19
Figure 6. Lifting location point weights and dimensions(a)
C B
= C.G.
X
D A
Y
(a) Optional AFD is not shown. See Figure 3, p. 13 for location of optional AFD. Lifting weights and center of gravity measurements are shown for both unit
configurations in tables below.
Table 7. Lifting weights

Location
Wye-Delta Units AFD Units
Unit Designator(a) Units A B C D A B C D
B1B1B1 lb 2495 1969 1901 2928 2611 1969 1900 3184
kg 1132 893 862 1328 1184 893 862 1445
B1C1D1 lb 3136 2264 1739 2698 3274 2264 1739 2931
kg 1422 1027 789 1224 1485 1027 789 1330
B2B2B2 lb 2522 1996 1926 2958 2637 1995 1927 3215
kg 1144 905 874 1342 1196 905 874 1459
B2C2D2 lb 3162 2297 1767 2726 2661 1995 1927 3191
kg 1510 1042 802 1237 1207 905 874 1448
C1D5E4 lb 3375 2479 2876 4243 3472 2478 2877 4520
kg 1531 1124 1305 1925 1575 1124 1305 2050
C1D6E5 lb 3330 2430 2825 4195 3426 2429 2824 4471
kg 1510 1102 1281 1903 1554 1102 1281 2028
C1E1F1 lb 4205 3046 3196 4271 4339 3047 3197 4509
kg 1907 1382 1450 1937 1968 1382 1450 2045
C2D3E3 lb 3612 2738 3148 4503 3708 2738 3148 4780
kg 1638 1242 1428 2043 1682 1242 1428 2168
C2D4E4 lb 3374 2479 2876 4243 3470 2478 2877 4520
kg 1530 1124 1305 1925 1574 1124 1305 2050
C2F2F3 lb 4649 3496 4707 4707 4786 3497 4707 4943
kg 2109 1586 2135 2135 2171 1586 2135 2242
D1D1E1 lb 3728 2758 3236 4694 3825 2758 3236 4970
kg 1691 1251 1468 2129 1735 1251 1468 2254
20 RTHD-SVX01G-EN
Table 7. Lifting weights (continued) (continued)

Location
Wye-Delta Units AFD Units
Unit Designator(a) Units A B C D A B C D
D1F1F2 lb 4526 3452 3615 4594 4662 3452 3616 4831
kg 2053 1566 1640 2084 2115 1566 1640 2191
D1G1G1 lb 4981 4148 4041 5076 5116 4149 4041 5312
kg 2259 1882 1833 2302 2320 1882 1833 2410
D1G2G2 lb 5216 4344 4231 5316 5679 4359 4100 5342
kg 2366 1970 1919 2411 2576 1977 1860 2423
D2D2E2 lb 3754 2818 3269 4720 3851 2818 3269 4996
kg 1703 1278 1483 2141 1747 1278 1483 2266
D2F2F3 lb 4737 3563 3722 4797 4874 3563 4797 5034
kg 2149 1616 2176 2176 2211 1616 2176 2283
D2G2G1 lb 5085 4255 4136 5171 5221 4255 4136 5409
kg 2307 1930 1876 2346 2368 1930 1876 2454
D2G3G3 lb 5320 4451 4327 5140 5715 4511 4259 5396
kg 2413 2019 1963 2331 2592 2046 1932 2448
D3D2E2 lb 3754 2818 3269 4720 3851 2818 3269 4996
kg 1703 1278 1483 2141 1747 1278 1483 2266
D3F2F3 lb 4737 3563 3722 4797 4874 3563 3721 5034
kg 2149 1616 1688 2176 2211 1616 1688 2283
D3G2G1 lb 5085 4255 4136 5171 5221 4255 4136 5409
kg 2307 1930 1876 2346 2368 1930 1876 2454
E3D2E2 lb 3796 2834 3300 4789 3904 2833 3300 5053
kg 1722 1285 1497 2172 1771 1285 1497 2292
E3F2F3 lb 4781 3582 3750 4851 5918 3583 3750 5087
kg 2169 1625 1701 2200 2231 1625 1701 2307
E3G2G1 lb 5158 4304 4226 5300 5294 4303 4226 5537
kg 2340 1952 1917 2404 2401 1952 1917 2512
E3G3G3 lb 5339 4455 4374 5486 5479 4454 4374 5729
kg 2422 2021 1984 2488 2485 2020 1984 2599
(a) Unit designator (digits 6, 7, 14, 15, 21 and 22 of unit model number)
RTHD-SVX01G-EN 21
Table 8. Center of gravity
Unit Wye-Delta Units AFD Units

Configuration(a) Units X Y Z X Y Z
B1B1B1 in 22.84 58.13 35.59 22.2 56.4 36.0
mm 580 1477 904 563 1433 915
B1C1D1 in 22.32 58.23 33.65 21.7 57.2 34.1
mm 567 1479 855 552 1454 866
B2B2B2 in 22.88 58.11 35.43 22.2 56.4 35.9
mm 581 1476 900 564 1433 911
B2C2D2 in 22.4 58.29 33.51 21.0 62.1 33.9
mm 569 1481 851 535 1578 862
C1D5E4 in 26.13 59.74 40.08 24.9 59.7 43.0
mm 664 1517 1018 633 1515 1093
C1D6E5 in 26.13 59.74 40.08 24.8 59.7 40.6
mm 664 1517 1018 630 1516 1032
C1E1F1 in 26.36 63.49 40.95 25.7 64.3 41.4
mm 670 1613 1040 652 1633 1052
C2D3E3 in 26.13 59.74 40.08 25.4 59.4 40.6
mm 664 1517 1018 646 1508 1031
C2D4E4 in 26.13 59.74 40.08 24.9 59.7 40.6
mm 664 1517 1018 633 1515 1032
C2F2F3 in 27.92 63.47 38.7 30.5 70.7 39.2
mm 709 1612 9833 774 1795 995
D1D1E1 in 25.91 60 40.47 25.1 59.6 41.0
mm 658 1524 1028 638 1514 1040
D1F1F2 in 27.92 63.47 38.7 27.3 64.2 39.2
mm 709 1612 983 693 1631 996
D1G1G1 in 30.58 68.56 37.79 29.6 62.1 38.2
mm 777 1741 960 753 1577 971
D1G2G2 in 30.77 63.55 37.72 29.6 62.1 38.2
mm 782 1614 958 753 1577 971
D2D2E2 in 25.97 59.95 40.31 25.3 59.6 40.8
mm 660 1523 1024 643 1513 1036
D2F2F3 in 27.7 63.4 38.14 31.1 72.0 38.6
mm 704 1610 969 789 1829 981
D2G2G1 in 30.58 68.56 37.79 30.2 63.0 38.2
mm 777 1741 960 767 1601 971
D2G3G3 in 30.85 63.48 37.44 30.2 63.0 38.2
mm 784 1612 951 767 1601 971
D3D2E2 in 25.97 59.95 40.31 25.3 59.6 40.8
mm 660 1523 1024 643 1513 1036
D3F2F3 in 27.7 63.4 38.14 27.1 64.1 38.6
mm 704 1610 969 687 1628 981
D3G2G1 in 30.58 68.56 37.79 30.3 63.2 38.2
mm 777 1741 960 769 1605 971
E3D2E2 in 25.9 60.05 40.5 25.3 59.6 41.0
mm 658 1525 1029 642 1513 1041
E3F2F3 in 27.64 63.46 38.33 27.0 64.2 38.8
mm 702 1612 974 686 1630 986
E3G2G1 in 30.8 63.55 38.70 30.5 64.1 39.1
mm 732 1614 983 776 1628 994
E3G3G3 in 30.8 63.91 37.62 30.2 63.5 39.4
mm 782.32 1621 956 767 1613 1001
(a) Unit designator (digits 6, 7, 14, 15, 21 and 22 of unit model number).
22 RTHD-SVX01G-EN
Lifting Procedure
Figure 7. Rigging configuration(a)

A
B
E D C
Anti-rolling
Cable
Eyelet or M16
Anti-rolling Internal Thread
Cable
F (min)
Lifting
Holes Starter Controls
44.5mm dia typ
Condenser Evaporator
Unit Model Number Location
(a) Optional AFD is not shown. See Figure 3, p. 13 for location of optional AFD. Rigging information is same for wye-delta or AFD units.
Table 9. Rigging dimensions
Unit Dimension - in (mm)

Configuration(a) Units A B C D E F
B1B1B1 in 120 108 56.97 3.92 21.02 24
mm 3048 2743 1447 97 534 610
B1C1D1 in 144 132 58.23 3.74 20.51 24
mm 3658 3353 1479 95 521 610
B2B2B2 in 120 108 58.11 3.86 21.06 24
mm 3048 2743 1476 98 535 610
B2C2D2 in 144 132 58.31 3.66 20.59 24
mm 3658 3353 1481 93 523 610
C1D5E4 in 120 108 59.96 8.62 22.99 24
mm 3048 2743 1523 219 584 610
C1D6E5 in 120 108 60 8.58 22.91 24
mm 3048 2743 1524 218 582 610
C1E1F1 in 144 132 63.50 5.08 24.57 24
mm 3658 3353 1613 129 624 610
C2D3E3 in 120 108 59.72 8.86 24.33 24
mm 3048 2743 1517 225 618 610
C2D4E4 in 120 108 59.96 8.62 22.99 24
mm 3048 2743 1523 219 584 610
C2F2F3 in 144 132 63.4 3.98 24.29 24
mm 3658 3353 1610 101 617 610
RTHD-SVX01G-EN 23
Table 9. Rigging dimensions (continued)
Unit Dimension - in (mm)

Configuration(a) Units A B C D E F
D1D1E1 in 120 108 60 7.36 24.09 24
mm 3048 2743 1524 187 612 610
D1F1F2 in 144 132 63.46 3.9 24.49 24
mm 3658 3353 1612 99 622 610
D1G1G1 in 144 132 63.46 3.9 25.75 24
mm 3658 3353 1612 99 654 610
D1G2G2 in 144 132 63.54 3.82 26.02 24
mm 3658 3353 1614 97 661 610
D2D2E2 in 120 108 59.96 7.4 24.17 24
mm 3048 2743 1523 188 614 610
D2F2F3 in 144 132 63.39 3.98 24.29 24
mm 3658 3353 1610 101 617 610
D2G2G1 in 144 132 63.46 3.9 25.75 24
mm 3658 3353 1612 99 654 610
D2G3G3 in 144 132 63.46 3.9 25.75 24
mm 3658 3353 1612 99 654 610
D3D2E2 in 120 108 60 7.4 24.17 24
mm 3048 2743 1523 188 614 610
D3F2F3 in 144 132 63.39 3.98 24.29 24
mm 3658 3353 1610 101 617 610
D3G2G1 in 144 132 63.46 3.9 25.75 24
mm 3658 3353 1612 99 654 610
E3D2E2 in 120 108 60 4.57 24.09 24
mm 3048 2743 1525 116 612 610
E3F2F3 in 144 132 63.46 1.14 24.21 24
mm 3658 3353 1612 29 615 610
E3G2G1 in 144 132 63.82 0.79 26 24
mm 3658 3353 1621 20 661 610
(a) Designator corresponds to digits 6, 7, 14, 15, 21 and 22 of model number.
Important: Rigging dimensions given in Table 9 are

given as a starting point reference. Lifting
cables should be adjusted as necessary for WARNING
even unit lift. Shipping Mounts!
WARNING Do not use the threaded holes in the compressor to lift
or assist in lifting the unit. They are not intended for
Improper Unit Lift! that purpose and could create a dangerous situation.
Failure to properly lift unit could result in unit dropping Do not remove the wood mounts until the unit is in its
and possibly crushing operator/technician which could final location. Removal of wood shipping mounts prior
result in death or serious injury, and equipment or to unit final locating could result in death or serious
property-only damage. Test lift unit approximately 24 injury or equipment damage.
inches to verify proper center of gravity lift point. To
avoid dropping of unit, reposition lifting point if unit is NOTICE:
not level.
Equipment Damage!
Never use a forklift to move the unit. The skid is not
WARNING designed to support the unit at any one point and
Risk of Unit Tipping! using a forklift to move the equipment may cause unit
damage. Always position the lifting beam so that
Failure to do so may result in death or serious injury cables do not contact the unit. Failure to do so may
should a lifting cable fail. Connect an anti-rotation strap result in unit damage.
between the lifting beam and compressor before lifting
unit.
24 RTHD-SVX01G-EN
Note: If absolutely necessary, the chiller can be pushed or

pulled across a smooth surface if it is bolted to Figure 8. Compressor shipping spacers
wood shipping mounts. B family (discharge side)
1. See Table 5, p. 16 or Table 6, p. 17 for unit shipping
weights. See Table 7, p. 20 for weights at each lift Compressor Housing
location. See Table 8, p. 22 for center of gravity
information.
Remove (1)
Note: Weights are typical for units with R-134a Puck-type Spacer
charge.
2. When unit is at its final location, remove shipping bolts
that secure unit to wood base mounts.
3. Install clevis connectors in lifting holes provided on the
unit. Attach lifting chains or cables to clevis connectors
as shown in Figure 7, p. 23. Each cable alone must be
strong enough to lift the chiller.
4. Attach cables to lifting beam as shown in Figure 7, Figure 9. Compressor shipping spacers
p. 23. See Table 9, p. 23 for rigging dimensions. The B family (suction side)
lifting beam crossbar must be positioned so the lifting
cables do not contact unit piping or electrical panel Compressor Housing
enclosure.
5. Connect an anti-rotation strap or cable loosely Remove (2)
between the lifting beam and the threaded coupling or Flat Water Spacers
eyelet provided at the top of the compressor. Use an
eyebolt or clevis to secure the strap at the coupling or
eyelet.
Important: The anti-rotation strap is not a lifting chain,
but a safety device to ensure that the unit
cannot tilt during lifting.
6. Lift from above, or jack the unit per “Alternate Moving
Method,” p. 26. Remove the base mounts.
7. During final positioning of the unit, place the isolation
pads under the evaporator and condenser tube sheet • C, D, E Family Compressors:
supports as shown in Figure 12, p. 26. See “Isolation
Pads,” p. 26 for information on isolation pads. • Remove (4) puck-type spacer under discharge
side of compressor (see Figure 10).
8. Level the unit as described in “Unit Leveling,” p. 26.
9. The unit is shipped with spacers on the compressor Figure 10. Compressor shipping spacers
mount that protect isolation pads during shipping and C, D, E family (discharge side)
handling. Before the unit is operated, remove the
spacers as indicated to prevent excessive noise. Compressor
Housing Remove (4)
• B Family Compressors: Puck-Type
• Remove qty 1 puck-type spacer under discharge Spacers
• Remove qty 2 flat washer spacers under suction
Note: Suction side of compressor WILL float.
RTHD-SVX01G-EN 25
10. Remove the shipping brackets from the bottom sides shell to level the unit. Unit should be level to within 1/
of the oil separator(s). See Figure 11. 4” (6.35 mm) over its length.
Figure 11. Oil separator shipping bracket 3. Place the level on the evaporator shell tube sheet
support to check side-to-side (front-to-back) level.
Adjust to within 1/4” (6.35 mm) of level front-to-back.
Note: The evaporator MUST be level for optimum heat
transfer and unit performance.
4. Use full-length shims to level the unit.
Alternate Moving Method

If it is not possible to rig from above as shown in Figure 7,
p. 23, the unit may also be moved by jacking each end high
Shipping Bracket enough to move an equipment dolly under each tube
sheet support. Once securely mounted on the dollies, the
unit may be rolled into position.
Notes:
• Once shipping bracket(s) is removed, the oil separator Isolation Pads
is only supported by the discharge line. Notes:
• Failure to remove oil separator shipping brackets could • The elastomeric pads shipped (as standard) are
result in excessive noise. adequate for most installations. For additional details
on isolation practices, see Trane Engineering Bulletin
Unit Leveling Sound Ratings and Installation Guide Optimus™
Note: The electrical panel side of the unit is designated as Water-Cooled Chillers RLC-PRB015*-EN, or consult an
the “front” of the unit. acoustical engineer for sound-sensitive installations.
1. Check unit level end-to-end by placing a level on the • Durometer values for isolator pads are a measure of
top surface of the evaporator shell. resilience. See Figure 12.
2. If there is insufficient surface available on the top of

evaporator shell, attach a magnetic level to bottom of
Figure 12. Isolator pad placement
Durometer: 50 ± 5 Durometer: 40 ± 5
0.31 0.31
Durometer: 55± 5
Typical Elastomeric
Isolation Pad
0.31
B
A
(hidden leg)
D
C
NOTE: Level unit to 1/4” (6.25mm)
across length and width.
Pads extend the full
width of the legs
26 RTHD-SVX01G-EN
Water Pressure Drop Data
RTHD-SVX01G-EN 27
28 RTHD-SVX01G-EN
RTHD-SVX01G-EN 29
30 RTHD-SVX01G-EN
Water Piping
Figure 13. Typical water piping setup
Cond Water
Shutoff Ref Valve (Opt)
Shutoff
Valves Relief Relief
Valves Isolation
Valve Valve
Isolation Valves
Manifold Manifold
Valves
Cond
Water
Evap Flow
Water
Flow
Flow Pressure
Flow Switch Differential
Pressure Switch Gauge
Thermometers
Differential Thermometers
Gauge
General Piping Connections

Note: Field piping must be arranged and supported to
NOTICE:
avoid stress on the equipment. It is strongly
recommended that the piping contractor provide at Equipment Damage!
least 3 feet (914 mm) of clearance between the pre- If using any commercial flushing/cleaning solution,
installation piping and the planned location of the construct a temporary bypass around the unit to
unit. This will allow for proper fit-up upon arrival of prevent damage to internal components of the
the unit at the installation site. All necessary piping evaporator/condenser. Trane assumes no responsibility
adjustments can be made at that time. Refer to the for equipment damage caused by flushing/cleaning
current engineering bulletin for further details on solutions or water-born debris.
installation.
Make water piping connections to the evaporator and
• Where specified, supply and install valves in the water condenser. Isolate and support piping to prevent stress on
piping upstream and downstream of the evaporator the unit. Construct piping according to local and national
and condenser water boxes, to isolate the shells for codes. Insulate and flush piping before connecting to unit.
maintenance and to balance/trim the system.
Use grooved pipe connectors for all water piping
• Supply and install condenser water control valve(s) per connections. Evaporator and condenser water inlet and
Engineering Bulletin RLC-PRB017*-EN. outlet sizes and locations are shown by the unit submittals.
• Supply or locate ship-with flow switches. Install flow The designation in the tables corresponds to the
switches or equivalent devices in both the chilled water compressor frame code followed by the evaporator shell
and condenser water piping. Wire the flow switches code followed by the condenser shell code as given in the
into the control system as indicated on the electrical unit model number, digits 6, 7, 14, 15, 21 and 22. Table 1,
schematics and field wiring diagrams, to ensure that p. 11 through Table 3, p. 13 list water connection
the unit can only operate when water flow is information.
established.
Reversing Waterboxes
• Supply and install taps for thermometers and pressure
gauges in water piping, adjacent to the inlet and outlet All water boxes may be reversed end-for-end. See
connections of both the evaporator and the condenser. “Maintenance Procedures,” p. 79 for detailed waterbox
removal instructions.
• Supply and install drain valves on each water box.
Remove sensors from wells before removing waterbox.
• Supply and install vent cocks on each water box.
Do not rotate water boxes. See Figure 14, p. 32 through
• Where specified, supply and install strainers ahead of Figure 16, p. 32 for correct orientation of the water inlet
all pumps and automatic modulating valves. and outlet.
• Supply and install refrigerant pressure relief piping Complete the water box switch and replace sensors.
from the pressure relief to the atmosphere.
Notes:
• If necessary, supply enough R-134a refrigerant and dry
nitrogen (75 psig) for pressure testing. • If water boxes are reversed, be sure to properly rewire
water temperature sensors in control panel.
• Where specified, supply and insulate the evaporator
• Be certain to replace water boxes right-side-up to
and any other portion of the unit, as required, to
maintain proper baffle orientation. Use new o-rings.
prevent sweating under normal operating conditions.
RTHD-SVX01G-EN 31
Figure 14. Condenser and evaporator waterboxes — BBB/BCD
OUT
IN IN 2 Pass Evap Connection

Configuration
(left or right hand)
COND EVAP Depending on Water Inlet
Figure 15. Condenser and evaporator waterboxes — CEF/CDE/DDE/EDE/DFF/EFF/CFF
OUT
IN IN
2 Pass Evap Connection
Configuration
COND EVAP (left or right hand)
Depending on Water Inlet
Figure 16. Condenser and evaporator waterboxes — DGG/EGG
OUT
OUT
IN
IN
3 Pass Evap Connection
Configuration
COND EVAP (left or right hand)
Depending on Water Inlet
32 RTHD-SVX01G-EN
Making Grooved Pipe Connections

NOTICE: NOTICE:
Equipment Damage! Evaporator Damage!
To prevent damage to water piping, do not overtighten To prevent evaporator damage, do not exceed 150 psig
connections. To prevent equipment damage, bypass (10.3 bar) evaporator water pressure for standard water
the unit if using an acidic flushing agent boxes. Maximum pressure for high pressure water
boxes is 300 psig (20.7 bar). Refer to digit 14 of the
Model No. To prevent tube damage, install a strainer in
Note: Make sure that all piping is flushed and cleaned the evaporator water inlet piping. To prevent tube
prior to starting the unit. corrosion, ensure that the initial water fill has a
balanced pH.
Vents and Drains
Install pipe plugs in evaporator and condenser water box Condenser Piping Components
drain and vent connections before filling the water
“Piping components” include all devices and controls
systems.
used to provide proper water system operation and unit
To drain water, remove vent and drain plugs, install a NPT operating safety. These components and their general
connector in the drain connection with a shutoff valve and locations are given below.
connect a hose to it.
Entering condenser water piping.
Evaporator Piping Components
• Air vents (to bleed air from system)
Note: Make sure all piping components are between the
• Water pressure gauges with shutoff valves
shutoff valves, so that isolation can be
accomplished on both the condenser and the • Pipe unions
evaporator. • Vibration eliminators (rubber boots)
“Piping components” include all devices and controls • Shutoff (isolation) valves. One per each pass
used to provide proper water system operation and unit
• Thermometers
operating safety. These components and their general
locations are given below. • Cleanout tees
Entering Chilled Water Piping • Pipe strainer

• Flow switch
• Water pressure gauges with shutoff valves Leaving condenser water piping.
• Pipe unions • Air vents (to bleed air from system)
• Vibration eliminators (rubber boots) • Water pressure gauges with shutoff valves
• Shutoff (isolation) valves • Pipe unions
• Thermometers • Vibration eliminators (rubber boots)
• Cleanout tees • Shutoff (isolation) valve - one per each pass
• Pipe strainer • Thermometers
• Flow switch • Cleanout tees
Leaving Chilled Water Piping • Balancing valve

• Pressure relief valve.
• Water pressure gauges with shutoff valves
NOTICE:
• Pipe unions
Condenser Damage!
• Vibration eliminators (rubber boots)
To prevent condenser damage, do not exceed 150 psig
• Shutoff (isolation) valves (10.3 bar) water pressure for standard water boxes.
• Thermometers Maximum pressure for high pressure water boxes is
300 psig (20.7 bar). Refer to digit 18 of the Model No. To
• Cleanout tees prevent tube damage, install a strainer in condenser
• Balancing valve water inlet piping. To prevent tube corrosion, ensure
that the initial water fill has a balanced pH.
• Pressure relief valve
RTHD-SVX01G-EN 33
Condenser Water Regulating Valve Water Treatment

The Condenser Head Pressure Control Option provides for
NOTICE:
a 0-10VDC (maximum range - a smaller range is
adjustable) output interface to the customer's condenser Proper Water Treatment!
water flow device. The condenser water flow device is The use of untreated or improperly treated water in a
typically a large butterfly type (6" or 8") automatic valve for RTHD chiller could result in scaling, erosion, corrosion,
200 to 400 Ton chillers. algae or slime. It is recommended that the services of a
qualified water treatment specialist be engaged to
The following guidelines must be met to ensure adequate determine what water treatment, if any, is required.
oil circulation throughout the system. Trane assumes no responsibility for equipment failures
• The chiller must maintain a 23 psid system pressure which result from untreated or improperly treated
differential at all load conditions in order to ensure water, or saline or brackish water.
adequate oil circulation.
Using untreated or improperly treated water in these units
• The entering condenser water temperature must be may result in inefficient operation and possible tube
above 55°F (12.8°C) or between 45°F (7.2°C) and 55°F
damage. Consult a qualified water treatment specialist to
(12.8°C) with a 1°F temperature rise per minute to 55°F
determine whether treatment is needed.
(12.8°C).
• Condenser leaving water temperature must be 17°F Water Pressure Gauges and Thermometers
degrees higher than evaporator leaving water Install field-supplied thermometers and pressure gauges
temperature within 2 minutes of startup. A 25°F (with manifolds, whenever practical) as shown in
differential must be maintained thereafter. Figure 13, p. 31. Locate pressure gauges or taps in a
If the above guidelines cannot be met, then some form of straight run of pipe; avoid placement near elbows, etc. Be
tower water control must be used. sure to install the gauges at the same elevation on each
shell if the shells have opposite-end water connections.
Condenser Water Regulating Valve To read manifolded water pressure gauges, open one
Adjustment valve and close the other (depending upon the reading
A separate Tracer® TU Settings Menu tab entitled desired). This eliminates errors resulting from differently
“Condenser Head Pressure Control - Setup” that is only calibrated gauges installed at unmatched elevations.
visible if the configuration is selected, contains the
following settings and manual overrides for user
Water Pressure Relief Valves
adjustments and commissioning all under one tab: NOTICE:
• “Off State” Output Command (0-10 Vdc 0.1 volt Equipment Damage!
increments, Default 2.0 Vdc)
Install a pressure relief valve in both evaporator and
• Output Voltage @ Desired Minimum Flow (Adj: 0 to condenser water systems. Failure to do so may result in
10.0 in 0.1 volt increments, Default 2.0 Vdc) shell damage.
• Desired Minimum Flow (Adj: 0- 100% of full flow in 1%
intervals, Default 20%) Install a water pressure relief valve in one of the condenser
and one of the evaporator water box drain connections or
• Output Voltage @ Desired Maximum Flow (Adj: 0 to
on the shell side of any shutoff valve. Water vessels with
10.0 in 0.1 volt increments (or finer), Default 10 Vdc)
close-coupled shutoff valves have a high potential for
• Actuator Stroke Time (Min to Max Range Time) (Adj: 1 hydrostatic pressure buildup on a water temperature
to 1000 seconds, in 1 second increments, Default 30s) increase. Refer to applicable codes for relief valve
• Damping Coefficient (adj: 0.1 to 1.8, in 0.1 increments, installation guidelines.
Default 0.5) Flow Sensing Devices
• Head Pressure Control Override (enumeration of:
Note: The installer must provide flow switches or
disabled (auto), “off” state, minimum, maximum
differential pressure switches with pump interlocks
(100%),) default:disabled (auto). When this setting is
to sense system water flow. Flow switch locations
in “disabled (auto)”
are schematically shown in Figure 13, p. 31.
The following setting is found in the Setpoints tab:
To provide chiller protection, install and wire flow switches
• Condenser Water Pump Prestart Time in series with the water pump interlocks, for both chilled
water and condenser water circuits (refer to the
Installation Electrical section). Specific connections and
schematic wiring diagrams are shipped with the unit.
Flow switches must stop or prevent compressor operation
if either system water flow drops off below the required
34 RTHD-SVX01G-EN
minimum shown on the pressure drop curves. Follow the Relief valve discharge setpoints and capacities rates are
manufacturer’s recommendations for selection and given in Table 10. Once the relief valve has opened, it will
installation procedures. General guidelines for flow switch re-close when pressure is reduced to a safe level.
installation are outlined below. Note: Once opened, relief valves may have tendency to
• Mount the switch upright, with a minimum of 5 pipe leak and must be replaced.
diameters straight, horizontal run on each side.
• Do not install close to elbows, orifices or valves. Figure 17. Relief valve location
Note: The arrow on the switch must point in the direction
of the water flow. Relief
Valves
• To prevent switch fluttering, remove all air from the
water system
Note: The UC800 provides a 6-second time delay on the
flow switch input before shutting down the unit on
a loss-of-flow diagnostic. Contact a qualified
service organization if nuisance machine
shutdowns persist.
• Adjust the switch to open when water flow falls below
nominal. See “General Information,” p. 9, general data
tables for minimum flow recommendations for
specific water pass arrangements. Flow switch Evaporator Shell
contacts are closed on proof of water flow.
Refrigerant Pressure Relief Valve Venting

WARNING *
Confined Space Hazards! Relief *
Failure to follow instructions below could result in Valves
death or serious injury. Do not work in confined spaces
where refrigerant or other hazardous, toxic or
flammable gas may be leaking. Refrigerant or other
gases could displace available oxygen to breathe,
causing possible asphyxiation or other serious health
risks. Some gases may be flammable and or explosive.
If a leak in such spaces is detected, evacuate the area
immediately and contact the proper rescue or response
authority.
Condenser Shell *Valve is hidden by pipe
Note: Vent pipe size must conform to the ANSI/ASHRAE
Standard 15 for vent pipe sizing. All federal, state, Pressure relief valve discharge capacities will vary with
and local codes take precedence over any shell diameter and length and also compressor
suggestions stated in this manual. displacement. Discharge venting capacity should be
All relief valve venting is the responsibility of the installing calculated as required by ASHRAE Standard 15-94. Do not
contractor. adjust relief valve setting in the field.
All RTHD units use evaporator, compressor, and
Table 10. Pressure relief valve data
condenser pressure relief valves (Figure 17, p. 35) that
must be vented to the outside of the building. Rated
Capacity Field
Relief valve connection sizes and locations are shown in
Discharge per Relief Conn
the unit submittals. Refer to local codes for relief valve vent Setpoint Number Valve Pipe Factory
line sizing information. Valve (psi) of (lba/ Size Shell Side
Location Valves min.) (NPT) Conn (in)
NOTICE: Evap - B1 200 1 48.0 1 1-5/16 -12
Equipment Damage! Evap - B2 200 1 48.0 1 1-5/16 -12
Do not exceed vent piping code specifications. Failure Evap -B3 200 1 48.0 1 1-5/16 -12
to comply with specifications may result in capacity
Evap -C1 200 1 48.0 1 1-5/16 -12
reduction, unit damage and/or relief valve damage.
Evap - C2 200 1 48.0 1 1-5/16 -12
RTHD-SVX01G-EN 35
Table 10. Pressure relief valve data (continued)

Thermal Insulation
Rated
Capacity Field All Optimus™ units are available with optional factory
Discharge per Relief Conn installed thermal insulation. If the unit is not factory
Setpoint Number Valve Pipe Factory insulated, install insulation over the areas shaded in
Valve (psi) of (lba/ Size Shell Side Figure 18, p. 36. See Table 11 for types and quantities of
Location Valves min.) (NPT) Conn (in) insulation required.
Evap - D1 200 1 48.0 1 1-5/16 -12
Notes:
Evap - D2 200 1 48.0 1 1-5/16 -12
• Liquid line filter, refrigerant charging valves, water
Evap - D3 200 1 48.0 1 1-5/16 -12
temperature sensors, drain and vent connections
Evap - D4 200 1 48.0 1 1-5/16 -12 when insulated must remain accessible for service.
Evap - D5 200 1 48.0 1 1-5/16 -12 • Use only water-base latex paint on factory-applied
Evap - D6 200 1 48.0 1 1-5/16 -12 insulation. Failure to do so may result in insulation
Evap - E1 200 1 48.0 1 1-5/16 -12 shrinkage.
Evap - F1 200 1 48.0 1 1-5/16 -12 • Units in environments with higher humidity or very
Evap - F2 200 1 48.0 1 1-5/16 -12 low leaving water temperature may require thicker
Evap - G1 200 1 78.8 1-1/4 1-5/8 - 12
insulation
Evap - G2 200 1 78.8 1-1/4 1-5/8 - 12
Evap - G3 200 1 78.8 1-1/4 1-5/8 - 12
Figure 18. Typical RTHD insulation requirement
Cond - B1 200 2 48.0 1 1-5/16 -12
Cond - B2 200 2 48.0 1 1-5/16 -12
Cond - D1 200 2 48.0 1 1-5/16 -12
Cond - D2 200 2 48.0 1 1-5/16 -12
Cond - E1 200 2 48.0 1 1-5/16 -12
Cond - E2 200 2 48.0 1 1-5/16 -12
Cond - E3 200 2 48.0 1 1-5/16 -12
Cond - E4 200 2 48.0 1 1-5/16 -12
Cond - E5 200 2 48.0 1 1-5/16 -12
Cond - F1 200 2 48.0 1 1-5/16 -12
Cond - F2 200 2 48.0 1 1-5/16 -12
Cond - F3 200 2 48.0 1 1-5/16 -12
Cond - G1 200 2 48.0 1 1-5/16 -12
Cond - G2 200 2 48.0 1 1-5/16 -12
Cond - G3 200 2 48.0 1 1-5/16 -12
Comp -
200 2 78.8 1-1/4 1-5/8 - 12
B1/B2*
Comp -
200 3 78.8 1-1/4 1-5/8 - 12
C1/C2*
Comp - Table 11. Recommended insulation types
200 3 78.8 1-1/4 1-5/8 - 12
D1/D2/D3*
Location Type Sq. Feet
Comp -E3* 200 3 78.8 1-1/4 1-5/8 - 12
Evaporator 3/4” wall 90
* Only used with isolation valve option
Compressor 3/4” wall 25
All components and piping on low side of
system (gas pump, return oil line, filter 3/4” wall 160
from pump)
36 RTHD-SVX01G-EN
Freeze Protection
For unit operation in a low temperature environment, glycol solution strengths are contained in Table 12 as
adequate protection measures must be taken against follows:
freezing. Adjusted settings and recommended ethylene
Table 12. Low refrigerant temperature, ethylene glycol, and freeze protection settings
DDE, EDE, CBC(b) DFF, EFF, CDE, BCD, BBB, CFF(b) DGG, EGG, CEF(b)
Chilled Low Rfgt Low Rfgt Solution Low Rfgt
Water Leaving Temp Rec % Solution Temp Rec % Freeze Temp Rec % Solution
Setpt Wtr Temp Cutout(c) Ethylene Freeze Cutout(c) Ethylene Point Cutout(c) Ethylene Freeze
(F)(a) Cutout (F) (F) Glycol Point (F) (F) Glycol (F) (F) Glycol Point (F)
40 34 28.6 0 32.0 28.6 0 32.0 28.6 0 32.0
39 33 27.2 2 30.6 27.6 1 31.3 27.9 0 32.0
38 32 25.7 4 29.1 26.5 3 30.1 27.2 2 31.1
37 31 24.2 6 27.6 25.4 5 28.9 26.5 3 30.2
36 30 22.7 8 26.1 24.2 6 27.7 25.7 4 29.3
35 29 21.1 11 24.5 23.0 8 26.4 24.9 6 28.3
34 28 20.2 12 23.6 22.1 10 25.5 24.0 7 27.4
33 27 19.2 13 22.6 21.1 11 24.5 23.0 8 26.4
32 26 18.1 15 21.5 20.1 12 23.5 22.0 10 25.4
31 25 17.0 16 20.4 18.8 14 22.2 20.6 12 24.0
30 24 15.9 17 19.3 17.6 15 21.0 19.3 13 22.7
29 23 14.8 18 18.2 16.6 16 20.0 18.4 14 21.8
28 22 13.6 20 17.0 15.5 17 18.9 17.4 15 20.8
27 21 12.4 21 15.8 14.4 18 17.8 16.4 16 19.8
26 20 11.2 22 14.6 13.3 20 16.7 15.4 17 18.8
25 19 9.9 23 13.3 12.1 21 15.5 14.3 19 17.7
24 18 8.6 24 12.0 10.9 22 14.3 13.2 20 16.6
23 17 7.3 25 10.7 9.7 23 13.1 12.1 21 15.5
22 16 5.9 26 9.3 8.4 24 11.8 10.9 22 14.3
21 15 4.5 27 7.9 7.1 25 10.5 9.7 23 13.1
20 14 3.1 28 6.5 5.8 26 9.2 8.5 24 11.9
19 13 1.6 30 5.0 4.4 27 7.8 7.3 25 10.7
18 12 0.1 31 3.5 3.1 29 6.5 6.0 27 9.4
17 11 -1.4 32 2.0 1.6 30 5.0 4.7 28 8.1
16 10 -2.9 33 0.5 0.2 31 3.6 3.3 29 6.7
15 9 -4.5 33 -1.1 -1.3 32 2.1 2.0 30 5.4
14 8 N/A 34 -2.8 -2.8 33 0.6 0.6 31 4.0
13 7 N/A 35 -4.4 -4.3 34 -0.9 -0.8 32 2.6
12 6 N/A 36 -6.1 N/A 34 -2.5 -2.3 33 1.1
11 5 N/A 37 -7.8 N/A 35 -4.1 -3.8 34 -0.4
10 4 N/A 38 -9.6 N/A 36 -5.7 -5.3 34 -1.9
(a) Column “Chilled Water Setpoint” becomes “Actual Leaving Solution Temperature” for ice-making.
(b) See unit model number digits 6, 14, 21
(c) “N/A” means chiller is not to be applied at leaving evaporator water temperatures, which results in the LRTC setting below those shown in the table.
Example For Ice Making:

Chilled Water Setpoint (std. comfort cooling) = 45°F
Full Load Delta T (across evaporator)= 6°F
Ice Termination Setpoint (entering water temp.) = 26°F
Actual Leaving Solution Temperature = 26 - 6 = 20°F
RTHD-SVX01G-EN 37
Installation Electrical
General Recommendations Important: Do not allow conduit to interfere with other
components, structural members or
As you review this manual, keep in mind that: equipment. Control voltage (115V) wiring in
• All field-installed wiring must conform to National conduit must be separate from conduit
Electric Code (NEC) guidelines, and any applicable carrying low voltage (<30V) wiring. To
state and local codes. Be sure to satisfy proper prevent control malfunctions, do not run
equipment grounding requirements per NEC. low voltage wiring (<30 V) in conduit with
• Compressor motor and unit electrical data is listed on conductors carrying more than 30 volts.
the chiller nameplate.
• All field-installed wiring must be checked for proper Electrical Data
terminations, and for possible shorts or grounds.
• For proper electrical component operation, do not Standard Units with Wye-Delta Starter
locate the unit in areas exposed to dust, dirt, corrosive See “Electrical Data Table Information,” p. 39. Electrical
fumes, or excessive humidity. If any of these component sizing should be based on actual jobsite
conditions exist, corrective action must be taken. operating conditions. This factor can be obtained through
Notes: the use of TOPSS™.
• Always refer to wiring diagrams shipped with chiller or
unit submittal for specific electrical schematic and Table 13. Compressor motor electrical data (60 Hz) —
connection information. standard units (wye-delta starter)
• All conduit must be long enough to allow compressor RLA @
and starter removal. Compressor Voltage Max LRA LRA
Code(a) (b) Max kW kW(c) (Wye) (Delta)
WARNING 200 174 557 970 3103
Proper Field Wiring and Grounding 230 174 484 818 2617
Required! B1, B2 380 174 291 488 1561
Failure to follow code could result in death or serious 460 174 241 400 1280
injury. All field wiring MUST be performed by qualified 575 174 193 329 1053
personnel. Improperly installed and grounded field 200 249 812 1173 3634
wiring poses FIRE and ELECTROCUTION hazards. To
230 249 698 936 2901
avoid these hazards, you MUST follow requirements
for field wiring installation and grounding as described C1, C2 380 249 421 558 1727
in NEC and your local/state electrical codes. 460 249 349 469 1453
575 249 279 375 1162
WARNING 200 329 1047 1690 5477
Hazardous Voltage w/Capacitors! 230 329 918 1532 4966

D1, D2 380 329 549 850 2755
Failure to disconnect power and discharge capacitors
before servicing could result in death or serious injury. 460 329 455 730 2366
Disconnect all electric power, including remote 575 329 367 612 1984
disconnects before servicing. Follow proper lockout/
(a) Unit model number digits 6 & 7.
tagout procedures to ensure the power cannot be (b) Voltage utilization ranges: 200V (180-220)m 230V (205-254), 380V
inadvertently energized. For variable frequency drives (342-418), 460V (414-506), 575V (516-633).
or other energy storing components provided by Trane (c) The RLA @ Max kW is based on the performance of the motor developing
full rated horsepower.
or others, refer to the appropriate manufacturer’s
literature for allowable waiting periods for discharge of
capacitors. Verify with an appropriate voltmeter that all
capacitors have discharged.
For additional information regarding the safe discharge
of capacitors, see PROD-SVB06A-EN.
38 RTHD-SVX01G-EN
Units with AFD Option

Table 14. Compressor motor electrical data (50 Hz) —
standard units (wye-delta starter)
Table 15. Electrical data — units with AFD
RLA @
Compressor Voltage Max LRA LRA Applied Range
Code(a) (b) Max kW kW(c) (Wye) (Delta) (Model Number Estimated Power
Voltage digits 56-58) Loss (W)
380 139 233 391 1229
0 - 126 1739
B1, B2 400 145 233 412 1296
127 - 150 2099
415 148 233 428 1348
151 - 185 2646
380 201 349 456 1414
575V 60 Hz 186 - 234 3071
C1, C2 400 209 349 480 1488
235 - 279 3719
415 213 349 498 1544
280 - 316 4460
380 271 455 711 2303
317 - 366 5023
D1, D2, D3 400 280 455 748 2424
0 - 176 2257
415 284 455 776 2515
177 - 223 2719
380 288 488 711 2303
224 - 280 3622
E3 400 301 488 748 2424 460V 60 Hz
281 - 335 3561
415 306 488 776 2515
336 - 411 4558
(a) Unit model number digits 6 & 7.
(b) Voltage utilization ranges: 380V (342-418), 400V (360-440), 415V 412 - 455 5703
(374-457).
(c) The RLA @ Max k@ is based on the performance of the motor developing 0 - 197 2555
full rated horsepower.
198 - 241 2949
Electrical Data Table Information 242 - 292 3764

380V 60 Hz
293 - 367 4109
Compressor motor electrical data is provided in Table 13,
p. 38 and Table 14 for each compressor size. Rated load 368 - 446 5129
amperes (RLA), locked rotor wye amperes (LRA) and 447 - 549 6663
expected inrush for the Wye-delta configurations are 0 - 197 2555
shown. 198 - 241 2949
Although the terms “LRA” and “expected inrush” are often 380V 50 Hz 242 - 292 3764
400V 50 Hz
used interchangeably, the distinction applied here is that 293 - 367 4109
415V 50 Hz
LRA is the rated inrush for the motor, but expected inrush
368 - 446 5129
is that allowed by the starter, based on the specific
447 - 549 6663
configuration. Selecting starters in the Wye-delta
configuration lowers expected inrush vs. the Delta (or Note: AFD input amps are shown in the RLA field of the unit nameplate.
“across-the- line”) configuration.

The RLA is based on the motor’s performance when Installer-Supplied Components
reaching full rated horsepower. The kW rating of the motor
Customer wiring interface connections are shown in the
will equal or exceed the kW requirement indicated by the
electrical schematics and connection diagrams that are
TOPSS™ selection program at design conditions. If motor
shipped with the unit. The installer must provide the
kW draw at design conditions is less than the kW rating of
following components if not ordered with the unit:
the motor, the RLA at design conditions is determined by
multiplying the motor RLA (at the desired voltage) by this • Power supply wiring (in conduit) for all field-wired
ratio: design kW/ motor kW rating. This calculation is connections.
performed within the computer selection program, • All control (interconnecting) wiring (in conduit) for
making RLA available as part of the design predictions. field supplied devices.
Predicted values include power factor variation from point
• Fused-disconnect switches or circuit breakers.
to point.
Optimus™ chillers are designed to operate satisfactorily
over a utilization range of ±10 percent of the standard
design voltages: (a) 200V, 230V, 380V, 460V, and 575V for
60 Hertz, 3- phase, and (b) 380V, 400V, 415V for 50 Hertz, 3-
phase.
RTHD-SVX01G-EN 39
Power Supply Wiring All power supply wiring must be sized and selected
accordingly by the project engineer in accordance with
NEC Table 310-16.
WARNING All wiring must comply with local codes and the National
Proper Field Wiring and Grounding Electrical Code. The installing (or electrical) contractor
must provide and install the system interconnecting
Required! wiring, as well as the power supply wiring. It must be
Failure to follow code could result in death or serious properly sized and equipped with the appropriate fused
injury. All field wiring MUST be performed by qualified disconnect switches.
personnel. Improperly installed and grounded field
wiring poses FIRE and ELECTROCUTION hazards. To The type and installation location(s) of the fused
avoid these hazards, you MUST follow requirements disconnects must comply with all applicable codes.
for field wiring installation and grounding as described
in NEC and your local/state electrical codes.
NOTICE:
Use Copper Conductors Only!
WARNING Failure to use copper conductors could result in
equipment damage as unit terminals are not designed
Hazardous Voltage w/Capacitors! to accept other types of conductors.
before servicing could result in death or serious injury. See Figure 19 for electrical installation panel locations.
Disconnect all electric power, including remote
tagout procedures to ensure the power cannot be
inadvertently energized. For variable frequency drives
or other energy storing components provided by Trane
or others, refer to the appropriate manufacturer’s
literature for allowable waiting periods for discharge of
Figure 19. Electrical Installation
6.1” x 14.6” (156x370mm)
opening for incoming line voltage
(8) 1/2” conduit knockout

for use with 30 volt wiring
Class II
30 VAC max
Low Voltage
VFD Drive Area
(6) 1/2” conduit and (4) 1-1/4” conduit
Line Voltage knockouts for use with 115 volts wiring
and Power Control Section
Section
Class I
132 VAC max
Control Voltage
Area
Evaporator
Condenser
40 RTHD-SVX01G-EN
Water Pump Power Supply 3. Connect the phase sequence indicator leads to the line
power terminal block (or the unit mounted disconnect)
Provide power supply wiring with fused disconnect for
as follows:
both the chilled water and condenser water pumps.
Phase Seq. Lead 1TB1 Terminal
Compressor Motor Phase Sequencing
Black (Phase A) L1
Always verify that proper rotation of the compressor is Red (Phase B) L2
established before the machine is started. Proper motor
Yellow (Phase C) L3
rotation requires confirmation of the electrical phase
sequence of the power supply. The motor is internally
4. Turn power on by closing the unit supply power
connected for clockwise rotation with incoming power
disconnect switch.
supply phased A, B, C.
5. Read the phase sequence on the indicator. The “ABC”
Units with Optional AFD. indicator on the face of the phase indicator will glow if
phase is “ABC”.
NOTICE:
Equipment Damage! WARNING
• Do not change AFD phase rotation to Hazardous Voltage w/Capacitors!
counterclockwise. Failure to disconnect power and discharge capacitors
• Do not enable phase reversal protection. before servicing could result in death or serious injury.
Changing default clockwise phase rotation or enabling disconnects before servicing. Follow proper lockout/
phase reversal protection could prevent proper chiller tagout procedures to ensure the power cannot be
operation or cause equipment damage. inadvertently energized. For variable frequency drives
or other energy storing components provided by Trane
AFD must be set with phase rotation clockwise (default or others, refer to the appropriate manufacturer’s
from factory), and phase reversal protection DISABLED. literature for allowable waiting periods for discharge of
All Units. To confirm the correct phase sequence (ABC), capacitors have discharged.
use a Model 45 Associated Research Phase indicator or
equivalent. For additional information regarding the safe discharge
Voltages generated in each phase of a polyphase
alternator or circuit are called phase voltages. In a three- 6. If “CBA” indicator glows instead, open unit main
phase circuit, three sine wave voltages are generated, power disconnect and switch two line leads on the line
differing in phase by 120 electrical degrees. The order in power terminal block (or the unit mounted disconnect).
which the three voltages of a three-phase system succeed Re-close main power disconnect and recheck phasing.
one another is called phase sequence or phase rotation.
7. Reopen the unit disconnect and disconnect the phase
This is determined by the direction of rotation of the
indicator.
alternator. When rotation is clockwise, phase sequence is
usually called “ABC,” when counterclockwise, “CBA.” Electrical Connections
This direction may be reversed outside the alternator by Proper starter/control panel line-side lug sizes are
interchanging any two of the line wires. It is this possible specified on the unit submittals. These lug sizes must be
interchange of wiring that makes a phase sequence compatible with conductor sizes specified by the electrical
indicator necessary if the operator is to quickly determine engineer or contractor.
the phase rotation of the motor.
For recommended field connection lug sizes (RTHD
Correcting Improper Electrical Phase Sequence. starters) see unit submittal.
Proper compressor motor electrical phasing can be quickly Circuit Breakers and Non-Fused Disconnect
determined and corrected before starting the unit. If using Switches 
an Associated Research Model 45 Phase Sequence
Indicator, follow this procedure:
(Factory Installed Option)
1. Press the STOP button to insure the unit will not Units that are ordered with factory installed circuit
attempt to start the compressor. breakers or non-fused disconnect switches ship with the
handle in the control panel. The handle must be installed
2. Open the electrical disconnect or circuit protection prior to starting the unit.
switch that provides line power to the line power
terminal block in the control panel (or to the unit- The operating mechanism is already pre-installed on the
mounted disconnect). Disconnect/ Circuit Breaker frame.
The hole locations and shafts lengths have already been
cut, and the shaft already installed.
RTHD-SVX01G-EN 41
WARNING WARNING
Hazardous Voltage w/Capacitors! Hazardous Voltage w/Capacitors!
Failure to disconnect power and discharge capacitors Failure to disconnect power and discharge capacitors
before servicing could result in death or serious injury. before servicing could result in death or serious injury.
Disconnect all electric power, including remote Disconnect all electric power, including remote
disconnects before servicing. Follow proper lockout/ disconnects before servicing. Follow proper lockout/
tagout procedures to ensure the power cannot be tagout procedures to ensure the power cannot be
inadvertently energized. For variable frequency drives inadvertently energized. For variable frequency drives
or other energy storing components provided by Trane or other energy storing components provided by Trane
or others, refer to the appropriate manufacturer’s or others, refer to the appropriate manufacturer’s
literature for allowable waiting periods for discharge of literature for allowable waiting periods for discharge of
capacitors. Verify with an appropriate voltmeter that all capacitors. Verify with an appropriate voltmeter that all
capacitors have discharged. capacitors have discharged.
For additional information regarding the safe discharge For additional information regarding the safe discharge
of capacitors, see PROD-SVB06A-EN. of capacitors, see PROD-SVB06A-EN.
1. Attach the handle and gasket to the enclosure door and Important: WHEN EVACUATING THE CHILLER’S
secure with the four bolts, lock washers and nut as REFRIGERANT SYSTEM, ALWAYS HAVE
shown in Figure 20. Tighten to 75 in-Lbs. THE MAIN POWER DISCONNECT/CIRCUIT
Note: There is an additional Lexan spacer on the handle, BREAKER OPENED. 
not shown in the Figure 20. Do not remove. Even when the compressor is not running,
voltage is present at the compressor motor
terminals, providing the potential for
Figure 20. Handle on door current to flow through a low impedance
path.
1/4-20 Hex Nut (4)
1/4” Lockwasher (4)
NOTICE:
Gasket Equipment Damage!
When removing refrigerant for the chiller, both the
condenser and chilled water pump must be operating
Lock
Plate to avoid freeze up.
NOTICE:
Motor Damage!
Fully disconnect all power sources before pumpdown
or evacuation procedures and ensure disconnects
cannot be closed while chiller is in a vacuum. Failure to
Cut Away of
Enclosure Door do so could cause motor damage.
Handle Plate
Sealing Washer (4) As the chiller is evacuated below atmospheric pressure,
(Used with 4 & 4X the dielectric strength (resistance to arcing) of the gaseous
Enclosures Only) atmosphere is significantly reduced. Because the SCRs are
1/4-20 x 1 Square Neck Bolt (4) connected “inside the delta,” three of the motor terminals
are connected directly to the line voltage. An “arc over”
Handle
can occur between motor terminals under conditions seen
2. Check that when the enclosure door is closed, the in the evacuation process. If this occurs the circuit breaker
handle interlocks with the shaft in all handle positions (or other external protective devices) will trip in response
except RESET/OPEN. To open the enclosure door when to high fault currents, and motor damage may also occur.
the breaker is in the ON position, rotate the screw slot To avoid motor damage, verify chiller fully disconnected
on the handle plate counter -clockwise. Verify from all power sources before beginning
operation. pumpdown or evacuation procedures, and use proper
lockout/tagout procedures to make sure the disconnect
cannot be accidentally closed while the chiller is in a
vacuum.
42 RTHD-SVX01G-EN
Module Connections for Chilled Water Flow Interlock

UC800 has an input that will accept a contact closure from
Interconnecting Wiring a proof-of-flow device such as a flow switch. The flow
All connectors can be unplugged or the wires can be switch is to be wired in series with the chilled water pump
removed from the screw assembly. If an entire plug is starter's auxiliary contacts. When this input does not prove
removed, make sure the plug and the associated jack are flow within 20 minutes relative to transition from Stop to
marked for proper location identification during Auto modes of the chiller, or if the flow is lost while the
reinstallation. chiller is in the Auto mode of operation, the chiller will be
inhibited from running by a non-latching diagnostic.The
NOTICE: flow switch input shall be filtered to allow for momentary
openings and closings of the switch due to turbulent water
Equipment Failure!
flow. This is accomplished with a 6 seconds filtering time.
Plugs and jacks must be clearly marked before The sensing voltage for the condenser water flow switch is
disconnecting, because specific plugs will fit into other 115/240 VAC.
jacks. Possible damage to equipment may occur if the
plugs are reversed with the jacks. Important: DO NOT cycle the chiller through starting
and stopping the chilled water pump. This
Interconnecting Wiring (Field Wiring Required) could cause the compressor to shut down
fully loaded. Use the external stop/start
Important: Do not turn chiller on or off using the chilled input to cycle the chiller.
water pump interlocks.
When making field connections, refer to the appropriate Condenser Water Pump Control
field layout, wiring, schematics and controls diagrams that UC800 provides a contact closure output to start and stop
ship with the unit. The diagrams in this manual are typical the condenser water pump. If condenser pumps are
only and may not match the unit. arranged in a bank with a common header, the output can
Whenever a contact closure (binary output) is referenced, be used to control an isolation valve and/or signal another
the electrical rating is: device that an additional pump is required.
7.2 amp resistive Condenser Water Pump Prestart time has been added to
At 120 VAC 2.88 amp pilot duty help with cold condenser water problems. In very cold
outdoor ambients, the cooling towers sump cold water
1/3 hp, 7.2 FLA, 43.2 LRA
would reach the chiller some time after the low system
5.0 amp resistive
differential pressure protection had run through its ignore
At 240 VAC 2.0 amp pilot duty time, and result in an immediate shutdown and latching
1/3 hp, 3.6 FLA, 21.6 LRA diagnostic. By simply starting the pump earlier, and
allowing mixing of the warmer indoor loop with the
Whenever a dry contact input (binary input) is referenced, cooling tower's sump, this problem can be avoided.
the electrical rating is 24VDC, 12 mA.
Condenser Water Flow Interlock
Whenever a control voltage contact input (binary input) is
The UC800 shall accept an isolated contact closure input
referenced, the electrical rating is 120 VAC, 5mA.
from a customer installed proof-of-flow device such as a
Note: Connections denoted with an asterisk require the flow switch and customer provided pump starter auxiliary
user to provide an external source of power. The contact for interlocking with condenser water flow. The
115V control power transformer is not sized for input shall be filtered to allow momentary openings and
additional load. closings of the switch due to turbulent water flow, etc. This
shall be accomplished with a 6 seconds filtering time. The
Chilled Water Pump Control
sensing voltage for the condenser water flow switch is 115/
UC800 has a evaporator water pump output relay that 240 VAC.
closes when the chiller is given a signal to go into the Auto
On a call for cooling after the restart inhibit timer has timed
mode of operation from any source. The contact is opened
out, the UC800shall energize the condenser water pump
to turn off the pump in the event of most machine level
relay and then check the condenser water flow switch and
diagnostics to prevent the build up of pump heat. To
pump starter interlock input for flow confirmation. Startup
protect against the build-up of pump heat for those
of the compressor will not be allowed until flow has
diagnostics that do not stop and/or start the pump and to
proven.
protect against the condition of a bad flow switch, the
pump shall always be stopped when the evaporator If flow is not initially established within 1200 seconds (20
pressure is seen to be close to the Low Side Evaporator minutes) of the condenser pump relay energizing, an
Pressure relief valve setting. automatically resetting diagnostic “Condenser Water
Flow Overdue” shall be generated which terminates the
prestart mode and de-energizes the condenser water
RTHD-SVX01G-EN 43
pump relay. This diagnostic is automatically reset if flow is Reset Ratio calculation:
established at any later time. The Reset Ratio on the User Interface is displayed as a
Note: This diagnostic would never automatically reset if percentage. To use it in the above equation it must be
UC800 was in control of the condenser pump converted to its decimal form.
through its condenser pump relay since it is Reset Ratio percent / 100 = Reset Ratio decimal
commanded off at the time of the diagnostic. It
could however reset and allow normal chiller Example of converting Reset Ratio:
operation if the pump was controlled from some If the Reset Ratio displayed on the User Interface is 50%
external source.
then use (50/100) = 0.5 in the equation.
Chilled Water Reset (CWR) Abbreviations used in equations:
The controller will reset the chilled water temperature • TOD = Outdoor Air Temp
setpoint based on either return water temperature, or
• TWE = Evap Entering Water Temp
outdoor air temperature. The Return Reset option is
standard, Outdoor Reset is optional. • TWL = Evap Leaving Water Temp
The following is selectable: Programmable Relays (Alarm and Status) -
• RESET TYPE Setpoint. Optional
This can be set to: DISABLE, CONSTANT, RETURN or UC800 provides a flexible alarm or chiller status indication
OUTSIDE AIR. The MP shall not permit more than one to a remote location through a hard wired interface to a dry
type of reset to be selected. contact closure. Four relays are available for this function,
• RESET RATIO Setpoints. and they are provided (generally with a Quad Relay Output
For outdoor air temp. reset, both positive and negative LLID) as part of the Alarm Relay Output Option.
reset ratios will be allowed. The events/states that can be assigned to the
• START RESET Setpoints. programmable relays are listed in the following table.
• MAXIMUM RESET Setpoints.
The maximum resets shall be with respect to the Table 16. Chiller events/status descriptions
chilled water setpoint. Event/State Description
When the chiller is running, if any type of CWR is enabled, This output is true whenever there is any active
the controller will step the CWS toward the desired CWS' diagnostic that requires a manual reset to clear,
(based on the below equations and setup parameters) at a Alarm - Latching that affects the Chiller, the Circuit, or any of the
Compressors on a circuit. This classification does
rate of 1 degree F every 5 minutes until the Active CWS not include informational diagnostics.
equals the desired CWS'. When the chiller is not running
This output is true whenever there is any active
the CWS will be fully reset immediately (within one diagnostic that could automatically clear, that
minute). The chiller will then start at the Differential to Start affects the Chiller, the Circuit, or any of the
value above a fully reset CWS or CWS' for Outdoor, Return, Alarm - Auto Reset Compressors on a circuit. This classification does
not include informational diagnostics. If all of the
and Constant Return Reset. auto resetting diagnostics were to clear, this output
would return to a false condition.
Equations for calculating CWR
This output is true whenever there is any
Equation used to get Degrees of Reset: diagnostic effecting any component, whether
Alarm latching or automatically clearing. This
Outdoor Air: classification does not include informational
diagnostics.
Degrees of Reset = 
Reset Ratio * (Start Reset - TOD) This output is true whenever there is any
Warning informational diagnostic affecting any component,
Return Reset: whether latching or automatically clearing.
Degrees of Reset = This output is true whenever the chiller has been
running in one of the Unloading types of limit
Reset Ratio * (Start Reset - (TWE - TWL)) modes (Condenser, Evaporator, Current Limit or
Constant Return: Phase Imbalance Limit) continuously for the last 20
minutes. A given limit or overlapping of different
Degrees of Reset =  limits must be in effect continuously for 20 minutes
prior to the output becoming true. It will become
100% * (Design Delta Temp - (TWE - TWL))
Chiller Limit Mode false, if no Unload limits are present for 1 minute.
To obtain Active CWS from Degrees of Reset: The filter prevents short duration or transient
repetitive limits from indicating. The chiller is
Active CWS = Degrees of Reset + Previous CWS considered to be in a limit mode for the purposes
of front panel display and annunciation, only if it is
Note: Previous CWS can either be Front Panel, BAS, or fully inhibiting loading by virtue of being in either
External the “hold” or “forced unload” regions of the limit
control, excluding the “limited loading region”.
44 RTHD-SVX01G-EN
Table 16. Chiller events/status descriptions (continued) Note: A “panic” stop (similar to “emergency” stop) can
be manually commanded by pressing the STOP
Event/State Description
button twice in a row, the chiller will immediately
The output is true whenever any compressors are shut down, but without creating a latching
started or running on the chiller and false when no
compressors are either starting or running on the
diagnostic.
Compressor
chiller.
Running
This status may or may not reflect the true status
Soft Loading
of the compressor in Service Pumpdown if such a Soft loading will prevent the chiller from going to full
mode exists for a particular chiller.
capacity during the pull-down period.
This relay output is energized anytime the chiller is
running in one of the following modes; Ice Making The UC800 control system has two soft loading algorithms
Mode or Condenser Pressure Limit Control Mode running all of the time. They are capacity control soft
continuously for the duration specified by the
Chiller Head loading and current limit soft loading. These algorithms
Chiller Head Relief Relay Filter Time. The Chiller
Pressure Relief introduce the use of a Filtered Chilled Water Setpoint and
Head Relief Relay Filter Time is a service setpoint.
Request Relay
The relay output is de-energized anytime the a Filtered Current Limit Setpoint. After the compressor has
chiller exits all above modes continuously for the been started, the starting point of the filtered chilled water
duration specified by the same Chiller Head Relief
Relay Filter Time. setpoint is initialized to the value of the Evap Leaving
Water Temperature. The filtered current limit setpoint is
The UC800 Service Tool (Tracer® TU) is used to install and initialized to the value of the Current Limit Softload
assign any of the above listed events or status to each of Starting Percent. These filtered setpoints allow for a stable
the four relays provided with this option. pull-down that is user adjustable in duration. They also
eliminate sudden transients due to setpoint changes
The default assignments for the four available relays are
during normal chiller operation.
listed below.
Three settings are used to describe the behavior of soft
Table 17 Programmable relays loading. The setup for softloading can be done using
Tracer® TU.
LLID
Software • Capacity Control Softload Time: This setting controls
Relay Output the time constant of the Filtered Chilled Water
LLID Name Designation Name Default Setpoint. It is settable between 0 and 120 min.
Status Relay 4, Head Pressure Relief • Current Limit Control Softload Time: This Setting
Relay 0
J2-1,2,3 Request
controls the time constant of the Filtered Current Limit
Status Relay 3, Chiller Limit Mode Setpoint. It is settable between 0 and 120 minutes.
Operating Relay 1
J2-4,5,6 Relay
Status • Current Limit Softload Starting Percent: This setting
Programmable Chiller Alarm Relay
Status Relay 2, controls the starting point of the Filtered Current Limit
Relays Relay 2 (latching or
J2-7,8,9
nonlatching) Setpoint. It is adjustable from 40 for RTHD to 100
Status Relay 1, Compressor Running percent RLA.
Relay 3
J2-10,11,12 Relay
External Base Loading - Optional
Emergency Stop Primarily for process control requirements, base loading
The UC800 provides auxiliary control for a customer provides for immediate start and loading of a chiller up to
specified/installed latching trip out. When this customer- an externally or remotely adjustable current limit setpoint
furnished remote contact is provided, the chiller will run without regard to differential to start or stop, or to leaving
normally when the contact is closed. When the contact water temperature control. This allows the flexibility to
opens, the unit will trip off on a manually resettable prestart or preload a chiller in anticipation of a large load
diagnostic. This condition requires manual reset at the application. It also allows you to keep a chiller on line
chiller switch on the front of the control panel. between processes when leaving water temperature
control would normally cycle the unit.
External Auto/Stop When the base loading option is installed through TD7 it
If the unit requires the external Auto/Stop function, the will be controllable through TD7/Tracer® TU, External
installer must provide leads from the remote contacts to Hardware Interface or Tracer (if Tracer is installed). Order
the proper terminals of the LLID on the control panel. for precedence for all setpoints, TD7/Tracer® TU, then
The chiller will run normally when the contacts are closed. External then Tracer from lowest to highest priority. If one
When the contact opens, the compressor(s), if operating, of the higher priority setpoints drops out due to a bad
will go to the RUN:UNLOAD operating mode and cycle off. sensor or communication loss then base loading shall go
Unit operation will be inhibited. Re-closure of the contacts to the next lowest priority of command and setpoint. The
will permit the unit to automatically return to normal command settings and control setpoints associated with
operation. base loading are explained below.
RTHD-SVX01G-EN 45
Base Loading Control Setpoint Compressor Percent RLA Output - Optional

This setpoint has three possible sources, an External UC800 provides a 2-10 Vdc analog output to indicate %RLA
Analog Input, TD7/Tracer® TU or Tracer®. of compressor starter average phase current. The values
• TD7/Tracer® TU Base Loading Control Setpoint of 2 to 10 Vdc correspond to 0 to 120% RLA.
• The range is 40 - 100% Compressor Load (Max %RLA).

The default is 50%.
AFD Drive (Optional)
• Tracer Base Loading Control Setpoint Trane TR200 drive is an electronic motor controller that
• The range is 40 - 100% Compressor Load (Max %RLA). converts AC mains input into a variable AC waveform
The default is 50%. output. The frequency and voltage of the output are
regulated to control the motor speed or torque.
• External Base Loading Setpoint
TR200 drive includes the following features:
This is an Analog Input that sets the base loading setpoint.
This signal can be controlled by either a 2-10Vdc or 4-20ma • Soft start to minimize inrush current
Signal based on configuration information. The equations • Improved harmonic mitigation with DC link reactor
show the relationship between input and percent • Integrated power fuse
compressor load:
• Graphical LCD keypad
If the input is configured as a 4 - 20 mA:
% Load = 3.75 * (mA Input) + 25 • Unit Mounted with factory pre-wiring
If the input is configured as a 2 - 10 Vdc: • ‘Trane Drive Utility’ for configuration and tracking
% Load = 7.5 * (Vdc Input) + 25 See Service Manual BAS-SVM01A-EN for more
information.
Ice Making Contact - Optional
UC800 accepts a contact closure input to initiate Ice AFD Drive Installation
Building. When in the ice building mode, the compressor The AFD drive is manufactured with a jumper installed
will be fully loaded (not given a low setpoint) and will between terminal 12 (+24Vdc source) and terminal 37
continue to operate until the ice contacts open or the (Safe Stop digital input). This jumper must be removed
return water temperature reaches the Ice Termination prior to unit operation. See Figure 21 for view of jumper as
Setpoint. If terminated on return setpoint, UC800 will not it would be installed on drive from manufacturer.
allow chiller to restart until ice making contact is opened.
Ice Machine Control - Optional NOTICE:

UC800 provides an output contact closure that can be used Equipment Damage!
as a signal to the system that ice building is in operation. Verify/remove jumper between AFD terminals 12 and
This relay will be closed when ice building is in progress 37 before unit operation. Failure to remove jumper
and open when ice building has been terminated by either could cause equipment damage.
UC800 or remote interlock. It is used to signal the system
changes required to convert to and from ice making. Figure 21. AFD jumper
External Chilled Water Setpoint - Optional

UC800 will accept either a 2-10 VDC or a 4-20 mA input (J9-
4, J9-5) signal, to adjust chilled water setpoint remotely.
External Current Limit Setpoint - Optional

UC800 will accept either a 2-10VDC or a 4-20mA input (J7-
11, J7-12) signal to adjust the current limit setpoint from a
remote location.
Percent Condenser Pressure Output - Optional

UC800 provides a 2-10 VDC analog output to indicate
percent High Pressure Cutout (HPC) condenser pressure.
Percent HPC = (Condenser Pressure/High Pressure Cutout
Jumper between
Setpoint)*100 terminals 12 and 37
must be removed
prior to unit
operation.
46 RTHD-SVX01G-EN
Important:
Table 18. Non-compressor specific parameter settings
• For factory provided AFD units, verify jumper has
been removed. ID Description Setting
• For field installed drives, remove jumper shown in 0-03 Region Settings North American
Figure 21. 0-20 Display Line 1.1 Small DC Link Voltage
0-22 Display Line 1.3 Heatsink Temp.
AFD Drive Programming 0-24 Display Line 3 Large Analog Input 53
0-40 [Hand on] Key on LCP Disabled
NOTICE:
0-41 [Off] Key on LCP Disabled
Equipment Damage! 0-60 Main Menu Password 999
• Do not change AFD phase rotation to 0-61 Access to Main Menu w/o Password Read Only
counterclockwise.
1-03 Torque Characteristics Compressor Torque
• Do not enable phase reversal protection. 1-71 Start Delay 0s
Changing default clockwise phase rotation or enabling 1-73 Flying Start Disabled
phase reversal protection could prevent proper chiller
1-78 Compressor Start Max Speed [Hz] 20Hz
operation or cause equipment damage.
1-79 Compressor Start Max Time to Trip 10s
Field replacement drives must be programmed via the 1-87 Trip Speed Low [Hz] 25Hz
keypad interface. Program non-compressor specific 3-02 Min Reference 30Hz
parameters first in sequential order (Table 18), followed by 3-41 Ramp 1 Ramp up Time 10s
compressor specific parameters (see Table 19) in
3-42 Ramp 1 Ramp Down Time 10s
sequential order.
3-82 Starting Ramp Up Time 5s
4-10 Motor Speed Direction Clockwise
4-12 Motor Speed Low Limit [Hz] 30Hz
4-18 Current Limit Max
5-02 Terminal 29 Mode Output
5-12 Terminal 27 Digital Input Coast Inverse
5-31 Terminal 29 Digital Output Alarm
5-40 Function Relay 1 No Operation
6-10 Terminal 53 Low Voltage 2V
6-14 Terminal 53 Low Ref./Feedb. Value 30Hz
6-50 Terminal 42 Output Power 4-20mA
14-00 Switching Pattern SFAVM
14-03 Overmodulation Off
14-10 Mains Failure [4] Kinetic Back-Up
14-12 Function at Mains Imbalance Derate
14-21 Automatic Restart Time 8s
14-50 RFI Filter Off
14-51 DC Link Compensation On
14-60 Function at Over Temperature Derate
14-61 Function at Inverter Overload Derate
14-62 Inv. Overload Derate Current 75%
RTHD-SVX01G-EN 47
Table 19. Compressor-specific parameter settings(a)
E3
Motor
Parameters B1/B2 Motor Frame C1/C2 Motor Frame D1/D2/D3/E3 Motor Frame Frame
460/ 400/ 380/ 575/ 460/ 400/ 380/ 575/ 460/ 400/ 380/ 575/ 400/
ID Description 60 50 60 60 60 50 60 60 60 50 60 60 50
Motor Power
1-21 233 194 233 233 334 280 334 334 441 375 441 441 403
(hp)
Motor Voltage
1-22 460 400 380 575 460 400 380 575 460 400 380 575 400
(V)
Motor
1-23 Frequency 60 50 60 60 60 50 60 60 60 50 60 60 50
(Hz)
Motor Current
1-24 241 233 291 193 349 349 421 279 455 455 549 367 488
(A)
Motor Nominal
1-25 3512 2921 3512 3512 3531 2938 3531 3531 3535 2943 3535 3535 2943
Speed (rpm)
Stator
1-30 Resistance 0.0303 0.0303 0.0213 0.0430 0.0201 0.0201 0.0138 0.0308 0.0122 0.0122 0.0087 0.0197 0.0122
(ohms)
Rotor
1-31 Resistance 0.0257 0.0257 0.0179 0.0365 0.0146 0.0146 0.0103 0.0227 0.0091 0.0091 0.0066 0.0144 0.0091
(ohms)
Main
1-35 Reactance 5.3684 5.3684 3.9634 8.0570 3.005 3.005 2.1972 4.8857 2.8882 2.8882 2.1848 4.8553 2.8882
(ohms)
Iron Loss
1-36 Resistance 188.388 188.388 142.836 280.73 152.612 152.612 116.132 243.61 125.549 125.549 90.188 193.85 125.549
(ohms)
Maximum
3-03 Reference 60 50 60 60 60 50 60 60 60 50 60 60 50
(Hz)
Motor Speed
4-14 High Limit 60 50 60 60 60 50 60 60 60 50 60 60 50
(Hz)
Terminal 53
High Ref./
6-15 60 50 60 60 60 50 60 60 60 50 60 60 50
Feedback
Value (Hz)
Switching
14-01 Frequency 3 3 3 2 3 3 3 2 3 3 3 2 3
(kHz)
Voltage at
14-11 391 340 323 489 391 340 323 489 391 340 323 489 340
Main Fault (V)
(a) Compressor frame size is shown in model number digits 6 and 7.
48 RTHD-SVX01G-EN
Communications Interface
LonTalk® Interface (LCI-C)
UC800 provides an optional LonTalk® Communication
Interface (LCI-C) between the chiller and a Building
Automation System (BAS). An LCI-C LLID shall be used to
provide “gateway” functionality between a LonTalk
compatible device and the Chiller. The inputs/outputs
include both mandatory and optional network variables as
established by the LONMARK® Functional Chiller Profile
8040.
Note: For more information see ACC-SVN100*-EN.
BACnet® Interface (BCI-C)

Optional BACnet® Communication Interface for Chillers
(BCI-C) is comprised of a Tracer® UC800 controller with
interface software. It is a non-programmable
communications module that allows units to
communicate on a BACnet communications network.
Note: For more information, see BAS-SVP01*-EN.
Modbus™ Remote Terminal Unit Interface

Modicon Communication Bus (Modbus™) enables the
chiller controller to communicate as a slave device on a
Modbus network. Chiller setpoints, operating modes,
alarms and status can be monitored and controlled by a
Modbus master device.
Note: For more information, see BAS-SVP01*-EN.
RTHD-SVX01G-EN 49
Operating Principles
This section describes the overall operating principles of the compressor to discharge pressure conditions.
the Optimus™ water chiller. Simultaneously, lubricant is injected into the compressor.
An oil management system provides an almost oil-free
General refrigerant to the shells to maximize heat transfer
performance, while providing lubrication and rotor
Optimus™ units are single-compressor water-cooled sealing to the compressor. The lubrication system ensures
liquid chillers. These units are equipped with unit- long compressor life and contributes to quiet operation.
mounted starter/control panels.
Immediately following the compression process the
The basic components are: lubricant and refrigerant are effectively divided using an
• Unit-mounted panel containing UC800 controller and oil separator.
input/output LLIDs The oil-free refrigerant vapor enters the condenser at State
• Helical-rotary compressor Pt. 2. Condensing is accomplished in a shell-and-tube heat
exchanger where refrigerant is condensed on the shell
• Evaporator
side and water flows internally in the tubes. Cooling tower
• Electronic expansion valve water, circulating through the condenser tubes, absorbs
• Water-cooled condenser with integral subcooler heat from this refrigerant and condenses it.
• Oil supply system As the refrigerant leaves the bottom of the condenser
(State Pt. 3), it enters an integral subcooler where it is
• Oil cooler (application dependent)
subcooled before traveling to the electronic expansion
• Related interconnecting piping valve (State Pt. 4). The pressure drop created by the
• AFD (optional) expansion process vaporizes a portion of the liquid
refrigerant.
Refrigeration Cycle The resulting mixture of liquid and gaseous refrigerant
then enters the Evaporator Distribution system (State Pt.
The refrigeration cycle can be described using the 5). The flash gas from the expansion process is internally
pressure-enthalpy diagram shown in Figure 22. Key State routed to compressor suction, and while the liquid
Points are indicated on the figure and are referenced in the refrigerant is distributed over the tube bundle in the
discussion following. evaporator.
Figure 22. Pressure/enthalpy curve Refrigeration Circuits

Each unit has a single refrigerant circuit. Each refrigerant
Liquid circuit includes compressor suction and discharge service
valves, removable core filter, charging port, and sight
3
4 2 glass. An electronically controlled expansion valve is
provided to maintain variable capacity modulation over
Pressure
the entire building load and maintain proper refrigerant

flow.
1
5
Compressor and Motor
Unit is equipped with a semi-hermetic, direct-drive, 3600
rpm 60 Hz (3000 rpm 50 Hz) rotary compressors that
Enthalpy includes a capacity control slide valve, oil sump heater,
and differential pressure refrigerant oil flow system.
The Optimus™ chiller makes use of a shell-and-tube Optional AFD provides capacity control with lower speeds.
evaporator design with refrigerant evaporating on the Four pressure-lubricated rolling element bearing groups
shell side and water flowing inside tubes having enhanced support the rotary assembly. Motor is suction gas-cooled,
surfaces.Refrigerant vapor leaves the evaporator as hermetically sealed, two-pole squirrel cage induction
saturated vapor (State Pt. 1). motor.
The refrigerant vapor generated in the evaporator flows to
the suction end of the compressor. The compressor is a Evaporator and Condenser
twin-rotor helical rotary type. The refrigerant flows across
the motor, providing the necessary cooling, then enters Heat exchangers are shell and tube design. Standard tubes
the compression chamber. Refrigerant is compressed in are externally finned, internally enhanced seamless
50 RTHD-SVX01G-EN
Operating Principles
copper with lands at all tube sheets. All tube sheets are
made of carbon steel. Tubes are mechanically expanded
into tube sheets and mechanically fastened to tube
supports. Evaporator tubes are 1.0- inch (25.4 mm)
diameter and condenser tubes are 0.75-inch (19.05 mm)
diameter. All tubes can be individually replaced.
Shells are carbon steel plate. The evaporator and
condenser are designed, tested, and stamped in
accordance with ASME Code for refrigerant-side/ working-
side pressure of 200 psig (13.8 bars).
All water pass arrangements are available with grooved
connections (150 or 300 psig waterside working pressure).
All connections may be either right- or left-handed.
Waterside shall be hydrostatically tested at 1.5X design
working pressure.
Oil Management
The unit is configured with an oil management system that
ensures proper oil circulation throughout the unit. The key
components of the system include an oil separator, oil
filter, oil sump and oil sump heater. An optional oil cooler
is installed when the unit is used for high condensing
temperature or low evaporator temperature conditions.
Unit-Mounted Starter
A unit-mounted starter and control panel is provided on
every chiller. Microprocessor-based unit control modules
(Tracer® UC800) provide for accurate chilled water control
as well as monitoring, protection and adaptive limit
functions. The “adaptive” nature of the controls
intelligently prevents the chiller from operating outside of
its limits, or compensates for unusual operating
conditions, while keeping the chiller running rather than
simply tripping due to a safety concern. When problems
do occur, diagnostic messages assist the operator in
troubleshooting.
RTHD-SVX01G-EN 51
Controls
Overview UC800 Specifications
Optimus™ RTHD units utilize the following control/ This section covers information pertaining to the UC800
interface components: controller hardware.
• Tracer® UC800 Controller
Wiring and Port Descriptions
• Tracer AdaptiView™ TD7 Operator Interface
Figure 23 illustrates the UC800 controller ports, LEDs,
rotary switches, and wiring terminals. The numbered list
following Figure 23 corresponds to the numbered callouts
in the illustration.
Figure 23. Wiring locations and connection ports
2 3 4 5
6 6
7
8
9
10
10 11
11
Front View Bottom View
1. Rotary Switches for setting BACnet® MAC address or MODBUS ID.

2. LINK for BACnet MS/TP, or MODBUS Slave (two terminals, ±). Field wired if used.
3. LINK for BACnet MS/TP, or MODBUS Slave (two terminals, ±). Field wired if used.
4. Machine bus for existing machine LLIDs (IPC3 Tracer bus 19.200 baud). IPC3 Bus: used for Comm4 using TCI or LonTalk® using LCI-C.
5. Power (210 mA at 24 Vdc) and ground terminations (same bus as item 4). Factory wired.
6. Not used.
7. Marquee LED power and UC800 Status indicator (Table 20, p. 53).
8. Status LEDs for the BAS link, MBus link, and IMC link.
9. USB device type B connection for the service tool (Tracer® TU).
10. The Ethernet connection can only be used with the Tracer AdaptiView™ display.
11. USB Host (not used).
52 RTHD-SVX01G-EN
Controls
Communication Interfaces
Table 20. LED behavior
There are four connections on the UC800 that support the
communication interfaces listed. See Figure 23, p. 52 for LED UC800 Status
the locations of each of these ports. Powered. If the Marquee LED is green solid, the
UC800 is powered and no problems exist.
• BACnet® MS/TP
Low power or malfunction. If the Marquee LED is
• MODBUS™ Slave Marquee LED red solid, the UC800 is powered, but there are
• LonTalk™ using LCI-C (from the IPC3 bus) problems present.
• Comm 4 using TCI (from the IPC3 bus) Alarm. The Marquee LED blinks Red when an alarm
exists.
Rotary Switches The TX LED blinks green at the data transfer rate
when the UC800 transfers data to other devices on
There are three rotary switches on the front of the UC800 LINK, MBUS, the link.
controller. Use these switches to define a three-digit IMC The Rx LED blinks yellow at the data transfer rate
address when the UC800 is installed in a BACnet or when the UC800 receives data from other devices on
the link.
MODBUS system (e.g., 107, 127, etc.).
The LINK LED is solid green if the Ethernet link is
Note: Valid addresses are 001 to 127 for BACnet and 001 connected and communicating.
Ethernet Link
to 247 for MODBUS. The ACT LED blinks yellow at the data transfer rate
when data flow is active on the link.
LED Description and Operation Service
The Service LED is solid green when pressed. For
qualified service technicians only. Do not use.
There are 10 LEDs on the front of the UC800. Figure 24
shows the locations of each LED and Table 20, p. 53 Important: Maintain at least 6” between low-voltage
describes their behavior in specific instances. (<30V) and high voltage circuits to prevent
control malfunctions, do not run low
Figure 24. LED locations voltage wiring (<30 V) in conduit with
conductors carrying more than 30 volts.
Marquee
Tracer AdaptiView™ TD7 Display
Operator Interface
Information is tailored to operators, service technicians,
and owners. When operating a chiller, there is specific
information you need on a day-to-day basis—setpoints,
limits, diagnostic information, and reports. Day-to-day
operational information is presented at the display.
Logically organized groups of information— chiller modes
of operation, active diagnostics, settings and reports put
information conveniently at your fingertips.
Figure 25. TD7 screens
Operator Display Boot Screen Display Loading Data Home Screen, Auto Mode
RTHD-SVX01G-EN 53
Controls
Home Screen Note: You can also access the Chiller Operating Modes
screen from the chiller status button in the upper
The home screen (Table 26) provides the most frequently left corner of the screen.
needed chiller status information on “touch targets” (the
entire white rectangular areas) for each chiller component. Figure 27. Chiller operating modes
Touching any touch target displays a screen containing
more chiller status information related to each
component.
Figure 26. Home screen
Table 21. Home screen items

Description Resolution Units
Active Chilled Water Setpoint X.X °F /°C
Active Current Limit Setpoint X.X %RLA
Average Motor Current %RLA X.X %RLA
Evap Entering/Leaving Water Temp X.X °F /°C
Cond Entering/Leaving Water Temp X.X °F /°C
Frequency Command X.X Hz
Evaporator Water Flow Status
Condenser Water Flow Status
Viewing Chiller Operating Modes

On the Reports screen, touch Chiller Operating Modes to
view the current operating status of the chiller in terms of
the top-level operating mode and submodes.
Table 22. Operating modes
Chiller Modes Description

MP Resetting
The chiller is not running and cannot run without intervention. Further information is provided
Stopped
by the sub-mode:
Local Stop Chiller is stopped by TD7 Stop button command– cannot be remotely overridden.
Chiller is stopped by the TD7 Panic Stop (by pressing Stop then Immediate Shutdown in succession) –
Immediate Stop
previous shutdown was manually commanded to shutdown immediately.
Diagnostic Shutdown – Manual Reset The chiller is stopped by a diagnostic that requires manual intervention to reset.
The chiller is currently being inhibited from starting (and running*), but may be allowed to start
Run Inhibit if the inhibiting or diagnostic condition is cleared. Further information is provided by the sub-
mode:
Diagnostic Shutdown – Auto Reset The entire chiller is stopped by a diagnostic that may automatically clear.
54 RTHD-SVX01G-EN
Controls
Table 22. Operating modes (continued)

Starting is Inhibited by External
The chiller is inhibited from starting (and running) by the “external stop” hardwired input.
Source
The chiller is inhibited from starting (and running) by command from a Building Automation System via
Start Inhibited by BAS
the digital communication link (com 4 or com 5).
This is a transient mode - 15-min. max, and is only possible if the chiller is in the Auto - Remote command
mode. After a power up reset, it is necessary to wait for valid communication from a Building Automation
Waiting for BAS Communications System (Tracer) to know whether to run or stay inhibited. Either valid communication will be received from
the Building Automation System (e.g. Tracer), or a communication diagnostic ultimately will result. In the
latter case the chiller will revert to Local control.
The compressor is currently being inhibited from starting as part of the power up start delay (or staggered
Power Up Delay Inhibit min:sec start) feature. This feature is intended to prevent multiple chillers from all starting simultaneously if power
is restored to all chillers simultaneously.
Low Differential Refrigerant Pressure
Contact your local Trane service office.
Cool-Down Time min:sec
The chiller is not currently running but can be expected to start at any moment given that the
Auto proper conditions and interlocks are satisfied. Further information is provided by the sub-
mode:
The chiller will wait up to 20 minutes in this mode for evaporator water flow to be established per the flow
Waiting For Evap Water Flow
switch hardwired input.
The chiller will wait indefinitely in this mode, for an evaporator leaving water temperature higher than the
Waiting for A Need to Cool
Chilled Water Setpoint plus the Differential to Start.
The chiller is not currently running and there is a call for cooling but start is delayed by certain
Waiting to Start
interlocks or proofs. Further information is provided by the sub-mode:
The chiller will wait up to 20 minutes in this mode for condenser water flow to be established per the flow
Waiting For Cond Water Flow
switch hardwired input.
Start Inhibited Waiting for Oil The chiller will wait up to 2 minutes in this mode for oil level to appear in the oil tank.
Condenser Water Pump Pre-Run Time The chiller will wait up to 30 minutes (user adjustable) in this mode for to allow the condenser water loop
min:sec to equalize in temperature
The compressor is currently unable to start due to its restart inhibit timer. A given compressor is not allowed
Restart Inhibit min:sec to start until 5 minutes (adj) has expired since its last start, once a number of “free starts” have been used
up.
The Chiller will wait for the time it takes the EXV to get to its commanded pre-position prior to starting
Waiting For EXV Preposition the compressor. This is typically a relatively short delay and no countdown timer is necessary (less than
15 seconds)
Only possible when Condenser Head Pressure Control option is enabled, this wait may be necessary due
Minimum Condenser Water min:sec
to the Head Pressure control device’s stroke time.
Condenser Water Regulating Control Only possible when Condenser Head Pressure Control option is enabled, this wait may be necessary due
min:sec to the Head Pressure control device’s stroke time
The chiller, circuit, and compressor are currently running. Further information is provided by
Running
the sub-mode:
The compressor is running and is being forced loaded to its step load point, without regard to the leaving
High Discharge Temp Limit
water temperature control, to prevent tripping on high compressor discharge temperature.
Chiller is running in “Base Load” operation where the capacity of the chiller is controlled to maintain a given
Base Loaded current per an adjustable set point. The chiller is forced to run without regard to the chilled water
temperatures and the differential to start and stop
The chiller is running, but loading is influenced by a gradual ‘pulldown” filter on the chilled water
Capacity Control Softloading temperature setpoint. The settling time of this filter is user adjustable as part of the softload control
feature.
The chiller is running, but loading is influenced by a gradual filter on the current limit setpoint The starting
Current Control Softloading
current and the settling time of this filter is user adjustable as part of the softload control feature.
Liquid level control of the Electronic Expansion Valve has temporarily been suspended. The EXV is being
modulated to control for a minimum differential pressure. This control implies low liquid levels and higher
EXV Controlling Differential Pressure
approach temperatures, but is necessary to provide minimum oil flow for the compressor until the
condenser water loop can warm up to approx 50F.
Unit is running in the Cooling Mode of operation and is attempting to control to the active Chilled Water
Chilled Water Control
Setpoint.
The chiller, circuit, and compressor are currently running, but the operation of the chiller/
Running – Limited compressor is being actively limited by the controls. Further information is provided by the sub-
mode.* See the section below regarding criteria for annunciation of limit modes
RTHD-SVX01G-EN 55
Controls
Table 22. Operating modes (continued)

The circuit is experiencing condenser pressures at or near the condenser limit setting. Compressors on the
Condenser Pressure Limit
circuit will be unloaded to prevent exceeding the limits.*
Low Evaporator Refrigerant The circuit is experiencing saturated evaporator temperatures at or near the Low Refrigerant Temperature
Temperature Inhibit Cutout setting. Compressors on the circuit will be unloaded to prevent tripping. *
The circuit is experiencing low refrigerant liquid levels and the EXV is at or near full open. The compressors
Capacity Limited by Low Liquid Level
on the circuit will be unloaded to prevent tripping.*
The compressor is running and its capacity is being limited by high currents. The current limit setting is
Current Limit 100% RLA (to avoid overcurrent trips) or lower as set by the compressor’s “share” of the active current
limit (demand limit) setting for the entire chiller.*
Phase Unbalance Limit The compressor is running and its capacity is being limited by excessive phase current unbalance.*
This is limit control that acts to prevent chiller shutdown when the discharge superheat approaches the
Low Discharge Superheat Limit
limit setpoint by reducing the liquid level and unloading the slide valve.
This is limit control that acts to prevent chiller shutdown when the estimated refrigerant flow approaches
Oil Loss Avoidance
the calculated minimum flow by increasing the slide valve capacity and/or VFD frequency
Note: Other normal running modes (see above) may also appear under this top level mode
The chiller is still running but shutdown is imminent. The chiller is going through a compressor
Shutting Down
run-unload. sequence. Shutdown is necessary due to one (or more) of the following sub-modes:
Local Stop Chiller is in the process of being stopped by TD7 Stop button command
immediate Stop Chiller is in the process of being stopped by TD7 Panic Stop command
Chiller is in the process of being stopped by a Latching Diagnostic shutdown – Manual Reset is required
Diagnostic Shutdown – Manual Reset
to clear
Chiller is in the process of being stopped by a Diagnostic shutdown – Automatic clearing of the diagnostic
Diagnostic Shutdown – Auto Reset
is possible if condition clears.
The compressor is in its “run – unload” state in which it is being continuously unloaded for 40 sec prior
Compressor Unloading (min:sec)
to shutdown.
Starting is Inhibited by External
Chiller is in the process of being stopped by the External Stop hardwired input
Source
The Chiller is in the process of shutdown due to a command from the Building Automation System (e.g.
Start Inhibited by BAS
Tracer)
Evaporator Water Pump Off Delay
min:sec
Service Override The Chiller is in a Service Override mode
The chiller, circuit, and compressor is running via a manual command to perform a Service Pumpdown.
Service Pumpdown Both evap and condenser water pumps are commanded to be running. The EXV is being held wide open,
but the manual liquid line service valve should be closed.
Alarms
Figure 28. Alarm screen
You can use the display to view alarms and to reset them.
Alarms are communicated to the display immediately
upon detection.
Viewing the Alarms Screen

Touch the Alarms button in the home screen menu
(Figure 26, p. 54) to view the Alarms screen. A table of
active alarms appears that is organized chronologically
with the most recent at the top of the list, as shown in
Figure 28. This example shows the default view, which
appears each time you return to the screen. List can be
sorted by any of the other columns if desired.
Note: A page number appears in the lower right corner of
the screen. If a screen contains more than one
page, up/down arrows also appear for viewing the
other pages. The Alarms screen is accessible by depressing the Alarms
enunciator. A verbal description will be provided.
A scrollable list of the last active Alarms is presented.
Performing a “Reset Alarms” will reset all active Alarms
56 RTHD-SVX01G-EN
Controls
regardless of type, machine or circuit. The scrollable list Editing a Custom Report
will be sorted by time of occurrence.
You can edit the custom report by adding, removing, or re-
“Alarms” Key Behavior: order data as follows:
• Alarm Shutdown (immediate) has occurred: Flash red 1. On the Custom Report screen, touch Edit. The Edit
• Alarm Shutdown (normal) has occurred: Flash yellow Custom Report screen appears.
• Informational warning is present: Flash blue 2. Add, remove, or re-order as follows:
No alarms present: Default button color, not flashing a. To add an item to the custom report, touch it. It
responds by changing to blue. You can use the
Reports arrows to scroll through the rest of the items that
can be added to the custom report. Then touch Add
You can use the TD7 display to view a variety of reports
to move the selected item to the box on the right
and to create and edit a custom report. All reports contain
side of the screen.
live data that refreshes every 2–5 seconds.
b. To remove an item from the custom report, touch it.
Viewing the Reports Screen It responds by changing to blue. You can use the
Touch the Reports button in the main menu area (Figure 4) arrows to scroll through the rest of the items that
to view the Reports screen. The Reports screen contains can be removed from the custom report. Then touch
the following buttons: Remove to move the selected item to the box on the
left side of the screen.
• Custom Report1
c. To re-order items in the custom report, touch it. It
• Custom Report2 responds by changing to blue. Use the arrows to
• Custom Report3 change the order of a highlighted item.
• Evaporator 3. To save and view your edited custom report, touch
• Condenser Save.
• Compressor Figure 30. Edit custom report screen

• Motor
• About
• Operating Modes
• Log Sheet
• ASHRAE Chiller Log
Each button links to the report named on the button.
Figure 29. Report screen
Figure 31. Report evaporator screen
The Reports tab allows a user to select from a list of reports

headings. Each report will generate a list of status items as
defined in the tables that follow.
RTHD-SVX01G-EN 57
Controls
Table 23. Report evaporator screen items Figure 33. Report compressor screen

Active Chilled Water Setpoint X.X °F / °C
Evaporator Entering Water Temperature X.X °F / °C
Evaporator Leaving Water Temperature X.X °F / °C
Evaporator Water Flow Status Flow, No Flow Text
Evaporator Water Pump Override Auto, On Text
Evaporator Approach Temperature X.X °F / °C
EXV Position Percent X.X %
Evaporator Refrigerant Pressure XXX.X PSIA/kPa
Evaporator Saturated Rfgt Temp X.X °F / °C
Evaporator Refrigerant Liquid Level X.XX in/mm
Figure 32. Report condenser screen

Table 25. Report compressor screen items

Compressor Running Status On, Off Text
Average Motor Current %RLA XX.X% %RLA
Compressor Starts XX Text
Compressor Running Time XX:XX Hr:Min
Oil Loss Level Sensor Wet, Dry Text
Discharge Temperature X.X °F / °C
Discharge Temperature X.X °F / °C
Compressor Oil Pressure XXX.X PSIA/kPaA
Evaporator Refrigerant Pressure XXX.X PSIA/kPaA
Condenser Refrigerant Pressure XXX.X PSIA/kPaA
Differential Refrigerant Pressure XXX.X PSIA/kPaA
Frequency Command XX.X Hz
Table 24. Report condenser screen items
Figure 34. Report motor screen
Condenser Entering Water
X.X F/C
Temperature
Condenser Leaving Water Temperature X.X F/C
Condenser Water Flow Status Flow, No Flow Text
Condenser Water Pump Override Auto, On Text
Condenser Approach Temperature X.X F/C
EXV Position Percent X.X %
Condenser Refrigerant Pressure XXX.X PSIA/kPa
Condenser Saturated Rfgt Temp X.X F/C
Differential Refrigerant Pressure XXX.X PSIA/kPa
Outdoor Air Temperature X.X F/C
58 RTHD-SVX01G-EN
Controls
Viewing and Changing Equipment Settings

Table 26. Report motor screen items
Each button in the Equipment Settings column on the
Description Resolution Units Settings screen takes you to a menu screen that contains
Active Current Limit Setpoint X.X %RLA
a group of buttons. Each button displays the name of a
setting and its current value (Figure 36). Touch any button
Average Motor Current %RLA X.X %RLA
to view a screen where you can change the setting for the
Starter Motor Current L1 %RLA X.X %RLA feature shown on the button.
Starter Motor Current L2 %RLA X.X %RLA
Note: A page number appears in the lower right corner of
Starter Motor Current L3 %RLA X.X %RLA the screen. If a screen contains more than one
Starter Motor Current L1 X.X A page, up/down arrows also appear for viewing the
Starter Motor Current L1 X.X A other pages, as in Figure 36.
Starter Motor Current L1 X.X A
Starter Input Voltage AB XXX.X V
Figure 36. Equipment setting screen
(Chiller setting shown)
Starter Input Voltage BC XXX.X V
Starter Input Voltage CA XXX.X V
Average Motor Current X.X A
Average Phase Voltage XXX.X V
Frequency Command XX.X Hz
Equipment Settings
You can use the TD7 display to monitor and change a
variety of equipment settings.
Viewing the Settings Screen
Touch the Settings button in the main menu area (see
Figure 26, p. 54) to view the Settings screen. Equipment
Settings identifies a column of buttons located on the
To change an equipment setting, follow this procedure:
screen (see the outlined column in Figure 35). The buttons
are: 1. Touch one of the button in the Equipment Settings
column on the Settings screen, such as Chiller Settings.
• Chiller Settings
The corresponding screen appears (in this case, the
• Feature Settings Chiller Settings screen).
• Chiller Water Reset 2. Touch the button that shows the equipment setting you
• Manual Control Settings want to change. A screen that allows you to change the
equipment setting appears. There are two types of
Each of these buttons provide access to a screen that
these screens:
contains additional buttons related to each topic. This
section provides detailed information about these a. For screens with button selections (Figure 37),
screens. touch the button that represents the setting you
want. The button becomes shaded, and a Save
Figure 35. Setting screen button appears at the bottom of the screen.
b. For screens with numerical keypads (Figure 38),
touch the appropriate numbers to change the
current value. The new value appears above the
keypad.
3. Touch Save to complete the change. The current value
is updated in the upper left side of the screen,
demonstrating that the change has been
communicated to the Tracer® UC800 controller. The
screen you were previously viewing appears.
RTHD-SVX01G-EN 59
Controls
Table 27. Settings screen items

Figure 37. Chilled water reset type screen
Chiller Settings
Active Chilled Water Setpoint XXX.X °F / °C
Active Current Limit Setpoint XXX % %RLA
Active Panel Base Load Cmd On/Auto Text
Active Base Loading Setpoint XXX %
Active Base Loading Command On/Auto Text
Differential to Start XXX.X °F / °C
Differential to Stop XXX.X °F / °C
Setpoint Source
BAS/Ext/FP Text
(BAS/Ext/FP, Ext/Front Panel, Front Panel)
Evaporator Water Pump Off Delay XX Min
Condenser Pump Prestart Time XX Min
High Evap Water Temp Cutout XXX.X °F / °C
Figure 38. Changed chilled water setpoint screen
Evaporator Leaving Water Temp Cutout XX.X °F / °C
Low Refrigerant Temperature Cutout XX.X °F / °C
Current Limit Softload Start Point XXX.X %
Current Limit Control Softload Time XXXX Sec
Capacity Control Softload Time XXXX Sec
Local Atmospheric Pressure XXX.X psi/kPa
Power Up Start Delay XXX Min
Feature Settings
External Chilled/Hot Water Setpoint
Text
(Enable/Disable)
External Current Limit Setpoint
Text
(Enable/Disable)
LCI-C Diagnostic Encoding (Enable/Disable) Text
Chilled Water Reset
Keypad features: Disable Text
(Constant, Outdoor, Return, Disable),
• When you enter a new number, the value in the New Return Reset Ratio XXX %
value field is deleted and replaced with the new entry. Return Start Reset XXX.X °F / °C
• The backspace (arrow) key deletes the characters you Return Maximum Reset XXX.X °F / °C
previously entered. Outdoor Reset Ratio XXX %
• If the keypad is used to enter a setpoint that is out of Outdoor Start Reset XXX.X °F / °C
range, an error dialog will appear when you touch the Outdoor Maximum Reset XXX.X °F / °C
Save button. Mode Overrides
• Keypads that allow negative numbers have positive Evap Water Pump (Auto, On) Auto Text
and negative number (+/-) keys. Cond Water Pump (Auto, On) Auto Text
60 RTHD-SVX01G-EN
Controls
Service Settings Each button provide access to a screen that is related to the
button name.
Setpoints on the Service Settings screen are only intended
for use by experienced service personnel. Setpoints Viewing and Changing Display Preferences
include security, if enabled. On the Settings screen, touch Display Preferences to view
The Service Settings screen is found through Chiller a screen containing these buttons (see Figure 29):
Settings, and includes a warning message for the user. • Date Format
• Date Separator
Figure 39. Warning message
• Time Format
• Unit System
• Pressure Units
• Number Format
Figure 41. Display preference screen
Figure 40. Service setting screen
Each of the buttons shows the name of a display

preference and its format (current value). Touch any of
these buttons to view a screen where you can change the
format. The button representing the format currently used
is shaded (see the “MMDDYYYY” button).
Figure 42. Date format page
Display Settings
You can use the Tracer AdaptiView™ display to change the
format of the information that appears on the display, and
to clean the touch screen.
Viewing the Settings Screen

Touch the Settings button in the main menu area
(Figure 26, p. 54) to view the Settings screen. Display
Settings identifies a column of buttons located on the
screen (see Figure 41). The buttons are:
• Display Preferences To change the format:
• Language 1. Touch the button that shows that format you prefer.
• Date and Time 2. Touch Save to confirm your selection and to return to
the Display Preferences screen.
• Clean Display
RTHD-SVX01G-EN 61
Controls
Date Format . Use the Date Format screen to choose 1. Touch the button that identifies the language you
from the following date formats: prefer.
• MMDDYYYY (default) 2. Touch Save to confirm your selection and to return to
the Settings screen.
• YYYYMMDD
• DDMMYYYY Figure 44. Date and time screen
Date Separator . Use the Date Separator screen to
choose from the following date formats:
• None
• Slash (default)
• Hyphen
Time Format . Use the Time Format screen to choose
from the following time formats:
• 12 hour (default)
• 24 hour
Units System . Use the Display Units screen to choose
from the following display units:
• SI The current date and time for the display is expressed as
the current value. The current value appears below the
• Inch-Pounds (default)
center line on the screen.
Pressure Units . Use the Pressure Units screen to Above the center line, the following date and time
choose from the following pressure units: attributes appear:
• kPaA (default if “SI” is chosen for display units) • Month
• kPaG • Day
• PSIA (default if “Inch-Pound” is chosen for display • Year
units)
• Hour
• PSIG
• Minute
Number Format .
• AM/PM
• 1000000.0
To change the date or time:
• 1000000,0
1. Touch the square presenting the attribute you want to
change. The square becomes highlighted.
Figure 43. Language page
2. Touch the up or down arrow key on the screen until the
your desired selection appears. Repeat the process for
any other attributes you want to change.
3. Touch Save to confirm your selection and return to the
Settings screen.
Note: Alternately, fields can be edited by touching the
highlighted square a second time to access a
keypad.
The language that is currently in use on the display is

expressed as the current value on the Language screen.
The button that displays the current value is shaded (see
the “English” buttoninFigure19as an example).
To change the language:
62 RTHD-SVX01G-EN
Controls
Cleaning the Display 3. Touch Save. The Settings screen appears with a Log
out button, in addition to the Security button.
On the Settings screen, touch Clean Display to disable the Figure 46. Security screen - disable
Tracer AdaptiView™ display screen for 5 seconds after
finger is removed. This process allows screen cleaning
without it responding to touch. During this time, the screen
is black with a number in the center that counts down the
seconds. After 5 seconds, the Settings screen re-appears.
Figure 45. Countdown screen
Figure 47. Security settings screen
Security Settings
If security if enabled, the Tracer AdaptiView™ display
requires that you log in with a four-digit security PIN to
make setting changes that are protected by security. This
feature prevents unauthorized personnel from doing so.
There are two levels of security, each allowing specific
changes to be made.
You can view all data without logging in. The log-in screen
appears only when you try to change a setting that is
protected by security, or when you touch the Log in button
Logging In
from the Settings screen.
There are two levels of security:
Disabling/Enabling Security • Security Level 1 allows users to change a limited group
The Tracer AdaptiView™ display gives you the ability to of secure settings. The default security PIN is 1111.
disable or enable the security feature that allows a user to • Security Level 2 allows users to change all secure
log in and log out. settings. The default security PIN is 7123.
To disable security, you must be logged in: A technician must use the Tracer® TU service tool to define
1. From the Settings screen, touch the Security button. a different PIN, or to recall a PIN that has been forgotten.
The Security screen appears (Figure 46). When defining a PIN in Tracer® TU, the technician enters
a 4-digit PIN that corresponds with the desired level of
Note: If you are logged out, the Log in screen appears.
security.
2. Touch the Disable button. The button becomes shaded.
To log in:
3. Touch Save. The Settings screen appears with only the
1. Touch the Log in button. The Log in screen appears
Security button visible. The Log in/Logout button is
(Figure 47).
gone.
2. Use the keypad to enter your PIN.
To enable security:
a. The PIN is a four-digit number, which was
1. From the Settings screen, touch the Security button.
configured for your system with the Tracer® TU
The Security screen appears (Figure 46).
service tool.
2. Touch the Enable button. The button becomes shaded.
b. As you enter the number, the PIN remains hidden
by asterisks.
Note: If you enter an invalid PIN, an error message
appears on the Log in screen.
RTHD-SVX01G-EN 63
Controls
3. Touch Save.
a. If you viewed the Log in screen from touching Log
in on the Settings screen, the Settings screen
appears with a Log out button on it.
b. If the Log in screen appeared when you tried to
change a setting, you return to that setting screen.
Note: The PIN is valid until 30 minutes of inactivity
passes, or until you log out.
Figure 48. Log in screen
Logging Out
To log out:
1. Touch the Log out button. A confirmation screen
appears (Figure 49).
2. Touch Yes to confirm that you want to log out. The
Settings screen appears with a Log in button on it.
Figure 49. Log out confirmation screen
64 RTHD-SVX01G-EN
Controls
Tracer® TU
Tracer® TU (non-Trane personnel, contact your local Trane Tracer® TU is designed to run on a customer’s laptop,
office for software) adds a level of sophistication that connected to the Tracer AdaptiView™ control panel with a
improves service technician effectiveness and minimizes USB cable. Your laptop must meet the following hardware
chiller downtime.TheTracer AdaptiView™ control’s and software requirements:
operator interface is intended to serve only typical daily • 1 GB RAM (minimum)
tasks. The portable PC-based service-tool software,
Tracer® TU, supports service and maintenance tasks. • 1024 x 768 screen resolution
Tracer® TU serves as a common interface to all Trane® • Ethernet 10/100 LAN card
chillers, and will customize itself based on the properties of • Available USB 2.0 port
the chiller with which it is communicating.Thus, the
• Microsoft® Windows® 7 Enterprise or Professional
service technician learns only one service interface.
operating system (32-bit or 64-bit) or Windows 8.1.
The panel bus is easy to troubleshoot using LED sensor
Important: Tracer® TU V8.6 was the final release to
verification. Only the defective device is replaced.Tracer®
support Windows XP. Beginning with
TU can communicate with individual devices or groups of
Tracer® TU V9.0, you will need to migrate to
devices.
Windows 7 or Windows 8.1 operating
All chiller status, machine configuration settings, system.
customizable limits, and up to 100 active or historic
Notes:
diagnostics are displayed through the service-tool
software interface. • Tracer® TU is designed and validated for this minimum
laptop configuration. Any variation from this
LEDs and their respective Tracer® TU indicators visually configuration may have different results. Therefore,
confirm the availability of each connected sensor, relay, support for Tracer® TU is limited to only those laptops
and actuator. with the configuration previously specified.
For more information, see TTU-SVN01*-EN Tracer® TU
Getting Started Guide.
Figure 50. Tracer® TU
RTHD-SVX01G-EN 65
Pre-Start
Upon completion of installation, complete the Optimus™
RTHD Installation Completion Check Sheet and Request
for Trane Service checklist in chapter “Log and Check
Sheets,” p. 95.
Important: Start-up must be performed by Trane or an
agent of Trane specifically authorized to
perform start-up and warranty of Trane
products. Contractor shall provide Trane (or
an agent of Trane specifically authorized to
perform start-up) with notice of the
scheduled start-up at least two weeks prior
to the scheduled start-up.
66 RTHD-SVX01G-EN
Start-Up and Shutdown
Important: Initial unit commissioning start-up must be 3. The unit will start normally, provided the following
performed by Trane or an agent of Trane conditions exist:
specifically authorized to perform start-up a. The UC800 receives a call for cooling and the
and warranty of Trane products. Contractor differential-to-start is above the setpoint.
shall provide Trane (or an agent of Trane
specifically authorized to perform start-up) b. All system operating interlocks and safety circuits
with notice of the scheduled start-up at least are satisfied.
two weeks prior to the scheduled start-up.
Extended Unit Shutdown
Unit Start-Up 4. Perform the normal unit stop sequence using the
<Stop> key.
NOTICE:
Note: Do not open starter disconnect switch. This must
Equipment Damage! remain closed to provide control power from the
Ensure that the compressor and oil sump heaters have control power transformer to the oil sump heater.
been operating properly for a minimum of 24 hours 5. Verify chilled water and condenser water pumps are
before starting. Failure to do so could result in
equipment damage. cycled off. If desired, open disconnect switches to the
pumps.
If required, once the system has been operating for 6. Drain condenser piping and cooling tower, if desired.
approximately 30 minutes and has become stabilized, 7. Remove the drain and vent plugs from the condenser
complete the remaining start-up procedures, as follows: headers to drain the condenser.
1. Check evaporator and condenser refrigerant pressures 8. Verify that the Crank Case heater is working.
under Refrigerant Report on the AdaptiView ™TD7. The
9. Once the unit is secured, perform the maintenance
pressures are referenced to sea level (14.6960 psia).
identified in the following sections.
2. Check EXV sight glasses after sufficient time has
elapsed to stabilize the chiller. The refrigerant flow past
sight glasses should be clear. Bubbles in the
Seasonal Unit Start-Up Procedure
refrigerant indicate either low refrigerant charge or 1. Close all valves and re-install the drain plugs in the
excessive pressure drop in the liquid line or a stuck evaporator and condenser heads.
open expansion valve. A restriction in the line can
sometimes be identified by a noticeable temperature 2. Service the auxiliary equipment according to the start-
differential between the two sides of the restriction. up/maintenance instructions provided by the
Frost will often form on the line at this point. See respective equipment manufacturers.
“General Information,” p. 9 for proper refrigerant 3. Vent and fill the cooling tower, if used, as well as the
charges. condenser and piping. At this point, all air must be
Important: A clear sight glass alone does not mean that removed from the system (including each pass). Close
the system is properly charged. Also check the vents in the evaporator chilled water circuits.
system subcooling, liquid level control and 4. Open all valves in the evaporator chilled water circuits.
unit operating pressures. 5. If the evaporator was previously drained, vent and fill
If chiller is limited by any limiting conditions, contact local the evaporator and chilled water circuit. When all air is
Trane service organization for more information. removed from the system (including each pass), install
the vent plugs in the evaporator water boxes.
Temporary Shutdown And NOTICE:
Restart Equipment Damage!
To shut down for a short time, use the following procedure: Ensure that the oil sump heaters have been operating
for a minimum of 24 hours before starting. Failure to do
1. Press the STOP key on the Adaptiview TD7. The so may result in equipment damage.
compressors will continue to operate and an
operational pumpdown cycle will be initiated. 6. Check the adjustment and operation of each safety and
2. UC800 pump control will turn off the pump (after a operating control.
minimum 1 min. delay) when the STOP key is pressed 7. Close all disconnect switches.
and automatically restart the pump when the unit
starts normally. 8. Refer to the sequence for daily unit startup for the
remainder of the seasonal startup
RTHD-SVX01G-EN 67
Sequence of Operation
This section will provide basic information on chiller • The text in the circles is the visible top level operating
operation for common events. With microelectronic mode displayed on Tracer™ AdaptiView.
controls, ladder diagrams cannot show today’s complex • The shading of each software state circle corresponds
logic, as the control functions are much more involved to the shading on the time lines that show the state the
than older pneumatic or solid state controls. chiller is in.
Adaptive control algorithms can also complicate the exact There are five generic states that the software can be in:
sequence of operations. This section illustrates common
control sequences. • Power Up
• Stopped
Software Operation Overview
• Starting
The Software Operation Overview shown in Figure 51 is a
• Running
diagram of the five possible software states. This diagram
can be though of as a state chart, with the arrows and • Stopping
•
arrow text depicting the transitions between states.

Figure 51. Software operation overview
RTHD Sequence Of
Operation Overview:
Power
Stopped Up
Stopped
Run Inhibit
ed Co Sta r
rm mm t
onfi own and
C utd
Sh
Auto
Stopping Fast Restart or Satisfied Setpoint Auto
Preparing to Shut Down Waiting to Start
Shutting Down Starting Compressor
Stop Command or Diagnostic
Sto
pC
om
ma art
Dia nd St
gn ed
os nfirm
tic Running Co
Running
Running - Limit
Timelines
• The time line indicates the upper level operating mode, • Boxes indicate control actions such as turning on
as it would be viewed on the Tracer AdaptiView™. relays, or pulsing compressor load or unload
• The shading color of the cylinder indicates the solenoids.
software state. • Smaller cylinders under the main cylinder indicate
• Text in parentheses indicates sub-mode text as viewed diagnostic checks.
on Tracer AdaptiView™. • Text outside a box or cylinder indicates time based
• Text above the time line cylinder is used to illustrate functions.
inputs to the Main Processor. This may include user • Solid double arrows indicate fixed timers.
input to the Tracer AdaptiView™ Touch screen, control • Dashed double arrows indicate variable timers.
inputs from sensors, or control inputs from a Generic
BAS.
68 RTHD-SVX01G-EN
Power Up
The Power up chart shows the respective TD7 screens state independent of the last mode. If the last mode before
during a power up of the main processor. This process power down was ‘Auto’, the transition from ‘Stopped’ to
takes from 30 to 50 seconds depending on the number of ‘Starting’ occurs, but it is not apparent to the user.
installed Options. On all power ups, the software model
will always transition through the ‘Stopped’ Software
Figure 52. Sequence of events: power up diagram
Operator Display Power Up Second Trane Logo - Loading

User Interface Template...
Display Ready
Black Screen
First Trane Logo Grey Screen Loading Data….
*Display will show

either Auto or Stop
button as “ ac tive”
(depressed) once
Black Screen
6/30/2012 it is ready
10 Sec 18 Seconds 5 Secc 90 second2
27
7oSeconds
SDeicpolnydrseady 15 Sec 15 Seconds
90 seconds to Disp
pllay read
dy
Operator Display Boot6t /Up
U14p/ 2and 7
o/a1d6/-290
a0n1d2 Load 0102sec Total to Display Ready
9 y 11/16// 20121122/11/2012
M ileston
ne Descrription M estoneMDielesscription
Mile sctroipnteioDnescription
(39 Seconds)
Minimum Time Until 1st Compressor Could Restart
(if “P ower Up Delay Inhibit” s et to 0; Default is 105 sec)) 6/14/2012 - 12/10/2012
Continue Along Start
Starting Sequence
Sequence
6/12/2012 - 12/11/2012 S ee “ P ower Up to
S ee “ P ower Up
External UC800 Boot Up S tarting” S equenc e Diagram
to S tarting”
Power
Applied Last Mode
Auto*
6/14/2012 7/16/2012 12/11/2012
Booting UC800
M ilestone
IF e DM
Milesto
M
esicleispttoin
oen Description Milesttone Description
(25 Seconds)
6i/s1p6l/a2y01a2n UC800 Last Mode
Operator D Display and Stop* Remain in
Figure 1 [A
S dtaarpttiBooting
Start BvoieowtinBgoot Screen] 6/12/2012 - 12/9/2012 “ S top” indefinitely
Stopped until “ A uto”
12/11//2012
UC800 Fully Operational command- See
IPC Bus Comm Begins “ S topped T o S tarting”
Figure 53. Sequence of events: TD7 screen displays
Operator Display Boot Screen Display Loading Data Home Screen, Auto Mode
RTHD-SVX01G-EN 69
Power Up to Starting
The Power up to starting diagram shows the timing from • Power up Start Delay setpoint set to 0 minutes
a power up event to energizing the compressor. The • Adjustable Stop to Start Timer set to 5 seconds
shortest allowable time would be under the following
conditions: • Need to cool
• No motor restart inhibit The above conditions would allow for a minimum power
up to starting compressor time of 95 seconds.
• Evaporator and Condenser Water flowing
Figure 54. Sequence of events: power up to starting
Last Mode Call for
Was Auto Cooling
Power Power Waiting to Waiting Waiting to Waiting Waiting Starting

Auto
Applied Up Start to Start Start to Start to Start Compressor
UC800 Confirm Evaporator Enforce Restart Condenser Confirm Presence of

Confirm Condenser Enforce 'Cprsr
Boot Time Water Flow Inhibit Timer Water Pump Oil With Optical Oil
Water Flow Strt Delay'
(22 to 32 Sec) (6 Second Filter) (0 to 30 mins) Pre-Run Sensor
Enforce Power Up Enforce 'Cond Pmp (6 Second Filter) (0 to 30 mins) (0 to 300 Sec) (0 to 2 mins)
Start Delay Timer Strt Delay'
(0 to 30 mins) (0 to 300 Sec)
Energize Evaporator Energize Condenser Energize Unload

Water Pump Relay Water Pump Relay Solenoid
Confirm Evaporator Water Confirm Condenser Water Pre-Position EXV

Flow Within 20 minutes Flow Within 20 minutes
(6 Sec Filter) (6 Sec Filter)
Oil Heater always energized

when compressor is de-energized
Overdrive EXV Open
70 RTHD-SVX01G-EN
Stopped to Starting
The stopped to starting diagram shows the timing from a • Power up Start Delay Timer has expired
stopped mode to energizing the compressor. The shortest • Adjustable Stop to Start Timer has expired
allowable time would be under the following conditions:
• Need to cool
• No motor restart inhibit
The above conditions would allow the compressor to start
• Evaporator and Condenser Water flowing in 60 seconds.
Figure 55. Sequence of events: stopped to starting
Chiller Mode Call for
Set to Auto Cooling
Stopped
Or Waiting Waiting Waiting Waiting Waiting Starting
Auto Compressor
Run to Start to Start to Start to Start to Start
Inhibit
Confirm Evaporator Enforce Restart Confirm Condenser Condense r Enforce 'Cprsr Confirm Presence of Oil
Water Flow Inhibit Timer Water Flow Water Pump Strt Delay' With Optical Oil Sensor
(6 Second Filter) (0 to 30 mins) (6 Second Filter) Pre-Run (0 to 300 Sec) (0 to 2 mins)
Enforce 'Cond (0 to 30 mins)

Pmp Strt Delay'
(0 to 300 Sec)

Confirm Evaporator Water Confirm Condenser Water Pre-Position EX V

(6 Sec Filter) (6 Sec Filter)
Oil Heater always ene rgized

when compressor is d e -
energized
Starting Wye-Delta
The Starting Wye-Delta shows the order of operation for this type of starter.
Figure 56. Sequence of events: Starting wye-delta
Energize Stop and Start
Relays
Confirm Proper Compressor Rotation

within 0.3 seconds (Phase Reversal)
and > 5% RLA (Phase Loss)
Confirm No Transition Complete Signal
(Transition Complete Input Shorted) Confirm > 10% RLA Compressor
Currents within 1.6 se conds
(Starter Fault Type III )
Energize Start and
Stop Relays When Currents Drop Below 85% RLA + 1 . 5
Seconds, Energize Transition Relay
Confirm No Compressor Currents

(Starter Fault Type I ) De-Energize Shorting
Relay
De-Energize Start and

Stop Relays Confirm Transition Complete
Input within 2.5 seconds
(Starter Did Not Transition)
Energize and Hold Energize Run

Shorting Relay Contactor
Confirm No Compressor Currents De-Energize Transition

(Starter Fault Type II ) Relay
Starting Compressor
Starting Compressor Starting Compressor
Compressor Running
Starting Compressor
Starter Contactor Integrity Test Transition Starter to Delta
in Wye
Max Accel Timer
(6 to 64 Seconds)
Arm/Run Command to Starter Module
RTHD-SVX01G-EN 71
Starting AFD
The Starting AFD shows the order of operation for this type of starter.
Figure 57. Sequence of events: starting AFD
Confirm At Speed Input within

Check for At Speed Input Opened Maximum Acceleration Timer
(Default 7 seconds)
Energize Stop and Start

Relays
Confirm Individual Phase

Currents are > 10% RLA
within 2.6 seconds
Accelerating
Compressor
(1 Second) (6 to 64 Seconds (Default 7 sec))
Waiting
To Start
Starting Compressor Running Running
Run Command to Starter Module
Running
The Running Diagram shows a typical running sequence.
Figure 58. Sequence of events: running
Starter
Status is Enter Exit
‘Running’ Limit Mode Limit Mode
'
Starting Running Running Running - Limit Running Running

Compressor
Run Unload
(15 Seconds)
Modulate Motor
Hold EXV Pre-position Modulate Motor Modulate Motor
Frequencye and Slide
(6 Seconds) Frequency and Slide Valve Frequency and Slide Valve
Valve for Limit Control
for Capacity Control for Capacity Control
Energize Unload Solenoid
for 15 Seconds Modulate EXV for Modulate EXV for
Modulate EXV for
Liquid Level Control Limit Control Liquid Level Control
Hold EXV at Prepostion for
6 Seconds
Enforce All Running Mode Diagnostics
72 RTHD-SVX01G-EN
Satisfied Setpoint
The Satisfied Setpoint diagram shows the normal transition from Running to shutting down due to the Evap Leaving water
temp falling below the differential to stop setpoint.
Figure 59. Sequence of events: satisfied setpoint
Satisfied Setpoint
Running Preparing to Shutdown Shutting Down Shutting Down Auto
Energize Unload Solenoid Open EXV Close EX V

(40 Seconds) (0-20 Seconds) (20 Seconds)
Energize Unload
Open EXV Close EX V
Solenoid
Pre-Position EX V
De-Energize Condenser to 38% Open for
Water Pump Relay Next Start
De-Energize Master Oil

Line Solenoid Valve
Continue to Energize Unload

Solenoid for 60 Mins
Energize Oil Heater
De-Energize
Compressor

Enforce All Running Mode Diagnostics
Within 0 - 30 Seconds
RTHD-SVX01G-EN 73
Normal Shutdown to Stopped or Run Inhibit

The Normal Shutdown diagram shows the Transition from Running through a Normal (friendly) Shutdown. The Dashed
lines on the top attempt to show the final mode if you enter the stop via various inputs.
Figure 60. Sequence of events: normal shutdown to stopped or run inhibit
Local Stop EXV Closed and Evap Pump Off Delay Complete
Normal Latching Diagnostic Stopped
Normal Non-Latching Diagnostic
Tracer Stop
Run Inhibit
External Auto-Stop
Stopped
Preparing or
Running Shutting Down Shutting Down
to Shutdown Run Inhibit
Energize Unload Solenoid Open EXV Close EX V

(40 Seconds) (0 to 20 Seconds) (20 Seconds)
Energize Unload De-Energize Close EX V

Solenoid Compressor
Open EXV
De-Energize Condenser
Water Pump Relay

Line Solenoid Valve
Energize Unload
Solenoid for 60 mins
Energize Oil Heater
Evap Pump Off Delay Time De-Energize Evaporator

(0-30 Minutes) Water Pump Relay
74 RTHD-SVX01G-EN
Immediate Shutdown to Stopped or Run Inhibit

The Immediate Shutdown diagram shows the Transition from Running through an Immediate Shutdown. The Dashed
lines on the top attempt to show the final mode if you enter the stop via various inputs.
Figure 61. Sequence of events: immediate shutdown to stopped or run inhibit
q p
EXV Closed and Evap
Immediate Shutdown to Stopped or Run Inhibit Pump Off Delay Complete
Immediate Shutdown Non-Latching Diagnostic Run Inhibit
Immediate Shutdown Latching Diagnostic
Stopped
Front Panel Immediate Shutdown
Run Inhibit
Running Shutting Down Shutting Down Shutting Down or
Stopped
Open EXV (0-20 Seconds) Close EXV (20 Seconds)
De-Energize
Close EX V
Condenser Water Pump
Energize Unload
Solenoid for 60 mins
De-Energize Evaporator
Water Pump Relay
Evap Pump Off Delay Time (0-30 Minutes)
Open EXV

Line Solenoid Valve
Energize Oil Heater
De-Energize
Compressor

8 Seconds after compressor is de-energiz e d
Momentary Power Loss

The Momentary Power Loss diagram shows how the controls act in a power interruption event that the controls diagnose
as a MPL diagnostic.
Figure 62. Sequence of events: momentary power loss
Momentary Power Loss Detected MPL Cleared and Need to Cool
Running Waiting to Start Starting

Shutting Down Cprsr
Energize Unload Solenoid Establish Cond Water Flow (6 sec Minimu m )

(40 Seconds)
Energize Oil Heater
Energize Condenser
Water Pump Relay
Energize Unload
Solenoid
Confirm Condenser Water Flow
Within 20 minutes
Enforce Power Up Start Delay Enforce Restart Inhibit Time r (6 Sec Filter)
(0 to 30 mins) (0 to 30 mins)
Enforce Stop to Start Timer

De-Energize (5 to 200 Seconds)
Compressor (30 Second Default)
Confirm No
Compressor Currents
Within 0-30 Seconds
De-Energize Condenser
Water Pump Relay
RTHD-SVX01G-EN 75
Ice Making (Running to Ice Making to Running)

This diagram show the transition from normal cooling to Ice making, back to normal cooling
Figure 63. Sequence of events: ice making (running to ice making to running)
Ice Making Command: Evap Leaving

Ice Making
1. Tracer Water Temp Rises
Command
2. External Above the
Withdrawn
3. Front Panel Differentail To Stop
Running Running
Running Running Running
(Unit is Building Ice) (Ice to Normal Transition)
Ice To Normal Transition Timer

( 0 to 10 Mins)
Open Slide Valve at Close Slide Valve Modulate Slide Valve

Maximum Rate for LWT Control
Ignore Softloading and De-Energize Head

Set CLS = 100% Relief Request Relay
Energize Ice Building De-Energize Head

Relay Relief Request Relay
Energize Head Relief

Request Relay
Head Relief Request Re lay
Delay ( 1 to 60 Mins)
Enforce All Limits and Running Mode Diagnostics
Ice Making (Auto to Ice Making to Ice Making Complete)

This diagram shows the transition from Auto to Ice making, to Ice Making Complete
Figure 64. Sequence of events: ice making (auto to ice making to ice making complete)
Ice Making Command: Evap Entering Water

1. Front Panel Temp Falls Below the
2. Tracer Ice Termination Setpoint
3. External Input
Run Inhibit
Starting Running Shutting Shutting (Ice
Auto Shutting Down
Cprsr (Unit is Building Ice) Down Down Building
Complete)
Close Slide Valve Open EXV Close EX V
(40 Seconds) (0 to 20 Sec) (20 Sec)
Open Slide Valve at De-Energize Condenser

Maximum Rate Close Slide Valve Water Pump Relay
Ignore Softloading and De-Energize Ice De-Energize Master Oil

Set CLS = 100% Building Relay Line Solenoid Valve
Energize Ice Building De-Energize Head Energize Oil Heater

Relay Relief Request Relay
Energize Head Relief Open EXV then

Head Relief Request Re lay Request Relay Close EX V
Delay (1 to 60 Mins)
De-Energize
Compressor

Enforce All Limits and Running Mode Diagnostics Within 8 Seconds
76 RTHD-SVX01G-EN
No Load Start
This diagram shows a pre-start sequence with the Start Sequence Type set to 'No Load'.
Figure 65. Sequence of events: no load start
Removal of all of the following:
External Stop
Local Stop Evap Leaving Water
Tracer/BAS Stop Temp Above the Diff to
Stop
Stopped
Or Waiting Waiting Waiting Waiting Waiting Starting
Auto Compressor
Run to Start to Start to Start to Start to Start
Inhibit
Confirm Evaporator Enforce Restart Confirm Condenser Condenser Enforce 'Cprsr Confirm Presence of Oil
Water Flow Inhibit Timer Water Flow Water Pump Strt Delay' With Optical Oil Sensor
(6 Second Filter) (0 to 30 mins) (6 Second Filter) Pre-Run (0 to 300 Sec) (0 to 2 mins)
Enforce 'Cond (0 to 30 mins)

Pmp Strt Delay'
(0 to 300 Sec)

Confirm Evaporator Water Confirm Condenser Water Pre-Position EXV

seconds (6 Sec Filter) (6 Sec Filter)
Oil Heater always energized

when compressor is de-
energized
Limit Conditions
UC800 will automatically limit certain operating parameters during startup and run modes to maintain optimum chiller
performance and prevent nuisance diagnostic trips. These limit conditions are noted in Table 28.
Table 28. Limit conditions
Condition Description
The chiller, circuit, and compressor are currently running, but the operation of the chiller/compressor is being actively
Running- limited
limited by the controls. Further information is provided by the sub-mode.
Condenser Pressure
The circuit is experiencing condenser pressures at or near the condenser limit setting. The compressor will be unloaded
Limit
to prevent exceeding the limits.
Low Evaporator
The circuit is experiencing saturated evaporator temperatures at or near the Low Refrigerant Temperature Cutout setting.
Refrigerant
The compressors will be unloaded to prevent tripping.
Temperature Inhibit
Capacity Limited by
The circuit is experiencing low refrigerant liquid levels and the EXV is at or near full open. The compressor will be unloaded
Low
to prevent tripping.
Liquid Level
The compressor is running and its capacity is being limited by high currents. The current limit setting is 100% RLA (to
Current Limit
avoid overcurrent trips).
Phase Unbalance
The compressor is running and its capacity is being limited by excessive phase current unbalance.
Limit
RTHD-SVX01G-EN 77
Maintenance
• Clean all water strainers in both the chilled and
condensing water piping systems.
WARNING
• Measure and log the subcooling and superheat.
Hazardous Voltage w/Capacitors! • See “Refrigerant and Oil Charge Management,” p. 78.
Failure to disconnect power and discharge capacitors If chiller measurements vary significantly from values
before servicing could result in death or serious injury. listed in Table 29 and Table 30, p. 79, problems may
Disconnect all electric power, including remote exist with refrigerant and oil charge levels. Contact
tagout procedures to ensure the power cannot be local Trane service.
inadvertently energized. For variable frequency drives
or other energy storing components provided by Trane Annual
or others, refer to the appropriate manufacturer’s Shut down the chiller once each year to check the
literature for allowable waiting periods for discharge of following:
capacitors have discharged. • Perform all weekly and monthly maintenance
procedures.
of capacitors, see PROD-SVB06A-EN. • Have a qualified laboratory perform an oil analysis to
determine system moisture content and acid level.
This section describes the basic chiller preventive Important: Due to the hygroscopic properties of the
maintenance procedures, and recommends the intervals POE oil, all oil must be stored in metal
at which these procedures should be performed. Use of a containers. The oil will absorb water if
periodic maintenance program is important to ensure the stored in a plastic container.
best possible performance and efficiency from a Stealth™
chiller. • Contact Trane service to leak check the chiller, inspect
safety controls, and inspect electrical components for
Use an Operator Log (see “Log and Check Sheets,” p. 95) deficiencies.
to record an operating history for unit. The log serves as a
valuable diagnostic tool for service personnel. By • Inspect all piping components for leakage and/or
observing trends in operating conditions, an operator can damage. Clean out any in-line strainers.
anticipate and prevent problem situations before they • Clean and repaint any areas that show signs of
occur. corrosion.
If unit does not operate properly during inspections, see • Inspect vent piping of all relief valves for presence of
“Diagnostics,” p. 83. refrigerant to detect improperly sealed relief valves.
Contact Trane service if unusual conditions are
Recommended Maintenance observed.
• Inspect the condenser tubes for fouling. Clean if
Weekly necessary. See “Cleaning the Condenser,” p. 79.
While the unit is running in stable conditions: • Check to make sure that the oil sump heater is working.
• Log the chiller. Scheduling Other Maintenance
• Check evaporator and condenser pressures with
• Use a nondestructive tube test to inspect the
gauges and compare to the reading on the Tracer
condenser and evaporator tubes at 3-year intervals.
AdaptiView™ TD7 or Tracer® TU service too. Pressure
readings should fall within operating ranges specified Note: It may be desirable to perform tube tests on these
in Table 29 and Table 30, p. 79. If chiller measurements components at more frequent intervals, depending
vary significantly from values listed in Table 29 and upon chiller application. This is especially true of
Table 30, p. 79, problems may exist with refrigerant critical process equipment.
and oil charge levels. Contact local Trane service. • Depending on chiller duty, contact Trane service
Note: Optimum condenser pressure is dependent on organization to determine when to conduct a complete
condenser water temperature, and should examination of the unit to determine the condition of
equal saturation pressure of refrigerant at a the compressor and internal components.
temperature 2 to 5F above that of leaving
condenser water at full load. Refrigerant and Oil Charge Management
Proper oil and refrigerant charge is essential for proper
Monthly unit operation, unit performance, and environmental
• Review operating log. protection. Only trained and licensed service personnel
should service the chiller.
78 RTHD-SVX01G-EN
Maintenance
Table 29 and Table 30 list baseline measurements for Mechanical Cleaning Procedure
Optimus™ units running at AHRI standard operating
Mechanical tube cleaning this method is used to remove
conditions. If chiller measurements vary significantly from
sludge and loose material from smooth-bore condenser
values listed below, problems may exist with refrigerant
tubes.
and oil charge levels. Contact Trane service.
Table 29. Operating conditions at full load(a) WARNING

Description Condition Heavy Objects!
Evaporator pressure 40-55 psig Failure to properly lift waterbox could result in death or
Condensing pressure 85-120 psig serious injury. Each of the individual cables (chains or
slings) used to lift the waterbox must be capable of
Discharge superheat 17oF
supporting the entire weight of the waterbox. The
Subcooling 5-10oF cables (chains or slings) must be rated for overhead
EXV percent open 40-50% open in Auto mode lifting applications with an acceptable working load
(a) All conditions stated above are based on the unit running fully loaded
limit.
at AHRI conditions. If full load conditions cannot be met, contact Trane
service.
WARNING
Table 30. Operating conditions at minimum load(a)
Heavy Objects!
Description Condition Failure to properly lift waterbox could result in death or
Evaporator approach *less than 7oF (non-glycol applications) serious injury. The proper use and ratings for eyebolts
Condensing approach *less than 7oF
can be found in ANSI/ASME standard B18.15.
Maximum load rating for eyebolts are based on a
Subcooling 2-3oF straight vertical lift in a gradually increasing manner.
EXV percent open 10-20 % open Angular lifts will significantly lower maximum loads
* 1.0oF for new unit. and should be avoided whenever possible. Loads
should always be applied to eyebolts in the plane of the
(a) Conditions at minimum must be: entering condenser water: 85F and entering
evaporator water: 55F
eye, not at some angle to this plane.
Waterbox Removal. Review mechanical room

Maintenance Procedures limitations and determine the safest method or methods
of rigging and lifting the waterboxes.
Cleaning the Condenser
Important:
NOTICE: • Do not rotate water boxes. See Figure 14, p. 32 through
Proper Water Treatment! Figure 16, p. 32 for correct orientation of the water inlet
and outlet.
The use of untreated or improperly treated water could
result in scaling, erosion, corrosion, algae or slime. It is • Be certain to replace water boxes right-side-up to
recommended that the services of a qualified water maintain proper baffle orientation. Use new o-rings.
treatment specialist be engaged to determine what 1. Determine the size of chiller being serviced. See unit
water treatment, if any, is required. Trane assumes no
nameplate located on chiller control panel.
responsibility for equipment failures which result from
untreated or improperly treated water, or saline or 2. Select the proper lift connection device from Table 33,
brackish water. p. 80. The rated lifting capacity of the selected lift
connection device must meet or exceed the published
Condenser tube fouling is suspect when the “approach” weight of the waterbox found in Table 32, p. 80.
temperature (i.e., the difference between the refrigerant
3. Ensure the lift connection device has the correct
condensing temperature and the leaving condenser water
connection for the waterbox. Example: thread type
temperature) is higher than predicted.
(course/fine, English/metric). Bolt diameter (English/
Standard water applications will operate with less than a metric).
10°F approach. If the approach exceeds 10°F, cleaning the
4. Properly connect the lift connection device to the
condenser tubes is recommended.
waterbox. See Figure 66. Ensure lift connection device
Note: Glycol in the water system typically doubles the is securely fastened.
standard approach.
5. Install hoist ring on to the lifting connection on the
If the annual condenser tube inspection indicates that the waterbox. Torque to 28 ft-lbs (37 Nm).
tubes are fouled, two cleaning methods can be used to rid
the tubes of contaminants.The methods are:
RTHD-SVX01G-EN 79
Maintenance
Figure 66. Waterbox lifting Table 32. Waterbox weights

Cables, Chains or Slings Number
Weight kg (lbs)
of Standard
Water Grooved Pipe Marine Style
Waterbox Size(a) Passes Waterbox(b) Waterbox(c)
G 4 164 (361) NA
G 3 208 (458) NA
Connection Device F 3 107 (235) NA
F 2 107 (235) NA
Evaporator D/E 3 91 (201) NA
D/E 2 110 (243) NA
Waterbox B/C 3 76 (167) NA
B/C 2 91 (201) NA
B/C 2 73 (160) NA
G 2 102 (226) 297 (655)
Condenser E/F 2 66 (146) 239 (526)
B/D 2 53 (116) 187 (412)
6. Disconnect water pipes, if connected. (a) Evaporator size is Digit 14 in the model number. Condenser is Digit 21
in model number.
7. Remove waterbox bolts (b) Lifting connection size M12x1.75.
(c) Lifting connection is a lifting lug. Removable cover has a weight of 138
8. Lift the waterbox away from the shell. kg (300 lbs). Lifting lug connection is M12x1.75.
Table 33. Connection devices

WARNING Unit Product Part Number
Overhead Hazard! Safety Hoist Ring
RTHD RNG01886
M12x1.75
Failure to follow these instructions could result in death
or serious injuries. Never stand below or in close
proximity to heavy objects while they are suspended Obtain the required parts from your local Trane Parts
from, or being lifted by, a lifting device. Do not leave Center.
waterbox suspended from lifting device.
Chemical Cleaning Procedure
9. Store waterbox in a safe and secure location and • Scale deposits are best removed by chemical means.
position. Consult a qualified water treatment specialist (i.e., one
10. Work a round nylon or brass bristled brush (attached to that knows the local water supply chemical/mineral
a rod) in and out of each of the condenser water tubes content) for a recommended cleaning solution suitable
to loosen the sludge. for the job. (A standard condenser water circuit is
composed solely of copper, cast iron and steel.)
11. Thoroughly flush the condenser water tubes with clean
Improper chemical cleaning can damage tube walls.
water.
All of the materials used in the external circulation system,
Note: To clean internally enhanced tubes, use a bi-
the quantity of the solution, the duration of the cleaning
directional brush or consult a qualified service
period, and any required safety precautions should be
organization for recommendations.
approved by the company furnishing the materials or
Reassembly. Once service is complete the waterbox performing the cleaning.
should be reinstalled on the shell following all previous Note: Chemical tube cleaning should always be followed
procedures in reverse. Use new o-rings or gaskets on all by mechanical tube cleaning.
joints after thoroughly cleaning each joint.
• Torque waterbox bolt in a star pattern. See Table 31 for Cleaning the Evaporator
torque values. Since the evaporator is typically part of a closed circuit, it
does not accumulate appreciable amounts of scale or
Table 31. RTHD Torque sludge. However, if cleaning is deemed necessary, use the
same cleaning methods described for the condenser
Evaporator Condenser
tubes.
65 ft-lbs (88 Nm) 65 ft-lbs (88 Nm)
80 RTHD-SVX01G-EN
Maintenance
Oil Sump Level Check 1. Run the unit fully unloaded for approximately 20
minutes.
Running the chiller at minimum load is the best for the
quickest return of oil to the separator and sump. The 2. Cycle the compressor off line.
machine still needs to sit for approximately 30 minutes
before the level is taken. At minimum load, the discharge
superheat should be highest. The more heat in the oil as it NOTICE:
lays in the sump, the more refrigerant will boil off in the Equipment Damage!
sump and leave more concentrated oil.
Never operate the compressor with the sightglass
The oil level in the oil sump can be measured to give an service valves opened. Severe oil loss will occur. Close
indication of the system oil charge. Follow the procedures the valves after checking the oil level. The sump is
below to measure the level. above the condenser and it is possible to drain the oil.
Figure 67. Determining oil level in sump
6” Sight tube Std Refrigeration Hose
3. Attach standard refrigeration hose with a sight tube in

the middle to the oil sump drain valve and the
condenser service valve at the top of the condenser.
Using high pressure rated clear hose with appropriate
fittings can help speed up the process.
Note: A shutoff valve at one end of the hose is
recommended to facilitate hose drainage after
oil level check is completed.
4. After the unit is off line for 30 minutes, move the
sightglass along the side of the oil sump.
5. The level should be between 2” and 5” from the
bottom of the oil sump.
Note: If oil levels are not between 2” and 5”, contact Trane
service.
RTHD-SVX01G-EN 81
Maintenance
Optional AFD Operational Inspection — Power Applied

Periodic Maintenance and Inspection
WARNING
AFD periodic maintenance and inspections should be
performed every 1–12 months, depending on operating Live Electrical Components!
environment. Failure to follow all electrical safety precautions when
exposed to live electrical components could result in
Visual Inspection — Power Removed death or serious injury. When necessary to work with
live electrical components, have a qualified licensed
WARNING electrician or other individual who has been properly
Hazardous Voltage w/Capacitors! trained in handling live electrical components perform
these tasks.
before servicing could result in death or serious injury.
1. Verify the drive cabinet cooling fans are operating. This
disconnects and discharge all motor start/run should be done from outside the enclosure, by looking
capacitors before servicing. Follow proper lockout/ into the cabinet at door and cabinet vents, to avoid
tagout procedures to ensure the power cannot be electrical hazards.
inadvertently energized. For variable frequency drives or Note: The power module fan comes on with power.
other energy storing components provided by Trane or Other fans cycle with drive operation.
others, refer to the appropriate manufacturer’s literature
for allowable waiting periods for discharge of 2. Check historic fault codes using AFD control panel
capacitors. Verify with an appropriate voltmeter that all (LCP).
Note: The AFD control panel is used ONLY for service and
For additional information regarding the safe discharge should never be used for machine operation.
3. Check configuration settings and confirm all proper
settings are still present in the controls.
1. Ensure the door interlocks are present and working.
4. Review the diagnostic history.
2. Verify the safety ground connections to the door
panels are securely connected. 5. Make Chiller Service report to document all setpoints.
3. Inspect power wire cables and devices to assure no 6. Check the UC800 alarm histories for any indications of
abrasion is occurring from vibrations against chassis operational problems.
of cabinets, or other edges. Choke Inspection
4. Ensure the drive interior and exterior is clear of any
As needed, replace the magnetic choke if there is physical
dust or debris. Fans, circuit boards, vents etc. must be
damage (for example, cracks).
clean.
Important: Only use a vacuum for cleaning. DO NOT
use compressed air.
5. Inspect the interior of the drive for any signs of
moisture entry or leakage.
6. Visually inspect all drive components and wiring. Look
for signs of heat or failure (look for swelled or leaking
capacitors, discolored reactors or inductors, broken
pre-charge resistors, smoke or arc trails on MOVs and
capacitors, etc.).
7. Closely inspect the motor terminal board for any signs
of leakage, arcing, etc.
8. Check ALL cable/lug/terminal connections inside the
drive enclosure. Ensure all are clean and tight, and not
rubbing against each other anywhere.
82 RTHD-SVX01G-EN
Diagnostics
Diagnostic Name and Source: Name of Diagnostic and in the table below, it will be displayed only as
its source. Note that this is the exact text used in the User “Informational Warning” as long as no circuit or chiller
Interface and/or Service Tool displays. shutdown results. If there is a shutdown and special action
Affects Target: Defines the “target” or what is affected defined in the table, then the Tracer® TU Diagnostics Page
by the diagnostic. Usually either the entire Chiller, or a display will indicate the shutdown type only.
particular Circuit or Compressor is affected by the Persistence: Defines whether or not the diagnostic and
diagnostic (the same one as the source), but in special its effects are to be manually reset (Latched), or can be
cases functions are modified or disabled by the diagnostic. either manually or automatically reset when and if the
None implies that there is no direct affect to the chiller, sub condition returns to normal (Nonlatched).
components or functional operation. Active Modes [Inactive Modes]: States the modes or
Note: Tracer® TU does not support the display of certain periods of operation that the diagnostic is active in and, as
targets on its Diagnostics pages although the necessary, those modes or periods that it is specifically
functionality implied by this table is supported. “not active” in as an exception to the active modes. The
Targets such as Evap Pump, Ice Mode, Heat Mode, inactive modes are enclosed in brackets, [ ]. Note that the
Chilled Water Reset, External Setpoints etc. – are modes used in this column are internal and not generally
displayed as simply “Chiller” even though they do annunciated to any of the formal mode displays.
not imply a chiller shutdown – only a compromise Criteria: Quantitatively defines the criteria used in
of the specific feature. generating the diagnostic and, if nonlatching, the criteria
Severity: Defines the severity of the above effect. for auto reset.
Immediate means immediate shutdown of the affected Reset Level: Defines the lowest level of manual
portion, Normal means normal or friendly shutdown of the diagnostic reset command which can clear the diagnostic.
affected portion, Special Action means a special action or The manual diagnostic reset levels in order of priority are:
mode of operation (limp along) is invoked, but without Local or Remote. For example, a diagnostic that has a reset
shutdown, and Info means an Informational Note or level of Remote, can be reset by either a remote diagnostic
Warning is generated. Design Note: Tracer® TU does not reset command or by a local diagnostic reset command.
support display of “Special Action”, on its Diagnostics
pages, so that if a diagnostic has a special action defined
Starter Diagnostics
Table 34. Starter diagnostics
Diagnostic Active Modes

Name and Affects [Inactive Reset
Source Target Severity Persistence Modes] Criteria Level
AFD Drive Fault Chiller Immediate Latch All The AFD Drive Fault Relay is open Local
The “At Speed” input was found to be opened with the
All Running Modes
At Speed Input compressor motor running after successfully obtaining
Chiller Immediate Latch after At Speed Local
Opened an at speed and bypassed condition. This is active for
proven
AFD
At Speed Input The “At Speed” input is shorted before the compressor
Chiller Immediate Latch Pre-Start Local
Shorted was started. This is active for AFD.
The compressor did not come up to speed (get to
<85%RLA) in the allotted time defined by the
Maximum Acceleration Timer and a transition was
Compressor Did
forced (motor put across the line) at that time. This
Not Accel: Chiller Info Latch Start Mode Remote
applies to all starter types. Note: Since RTHD SSS has
Transition
no forced transition capability, this info warning can be
followed with a “Compressor did not accelerate fully”
diagnostic above and an aborted start.
The starter module did not receive an “Up to Speed” or
Compressor Did “End of Ramp” signal from the SSS within 2.5 seconds
Not Accelerate Chiller Immediate Latch Start Mode after commanding a bypass, or after the maximum Local
Fully acceleration time had expired, whichever is longer. This
diagnostic only applies to SSS/AFD.
The compressor did not come up to speed (get to
Compressor Did
<85%RLA) in the allotted time defined by the
Not Accelerate: Chiller Immediate Latch Start Mode Remote
Maximum Acceleration Timer and the start was aborted
Shutdown
per the starter configuration selected.
RTHD-SVX01G-EN 83
Diagnostics
Table 34. Starter diagnostics (continued)

All compressor • Momentary Power Loss option disabled: No effect.
running and • Momentary Power Loss option enabled: A loss of
Momentary stopping modes power on three line cycles or more was detected.
Chiller Immediate Nonlatch Remote
Power Loss [all compressor Diagnostic is reset in 30 seconds.
starting and non-
running modes]
Compressor current exceeded overload time vs. trip
Motor Current
Chiller Immediate Latch Chiller Energized characteristic. For A/C products Must trip = 140% RLA, Local
Overload
Must hold=125%, nominal trip 132.5% in 30 seconds
a. Average of all monitored Line voltages above + 10%
of nominal. [Must hold = + 10% of nominal. Must trip
= + 15% of nominal. Reset differential = min. of 2%
Over Voltage Chiller Normal NonLatch All and max. of 4%. Time to trip = minimum of 1 min. and Remote
maximum of 5 min.) Design: Nom. trip: 60 seconds at
greater than 112.5%, + or - 2.5%, Auto Reset at 109%
or less.
a) No current was sensed on one or two of the current
transformer inputs while running or starting (See
Nonlatching Power Loss Diagnostic for all three phases
lost while running). Must hold = 20% RLA. Must trip =
5% RLA. Time to trip shall be longer than guaranteed
Start Sequence and
Phase Loss Chiller Immediate Latch reset on Starter Module at a minimum, 3 seconds Local
Run modes
maximum. Actual design trip point is 10%. The actual
design trip time is 2.64 seconds. b) If Phase reversal
protection is enabled and current is not sensed on one
or more current xformer inputs. Logic will detect and
trip in a maximum of 0.3 second from compressor start.
Compressor A phase reversal was detected on the incoming current.
energized to On a compressor startup the phase reversal logic must
Phase Reversal Chiller Immediate Latch Local
transition command detect and trip in a maximum of 0.3 second from
[All Other Times] compressor start.
The compressor had previously established currents
while running and then all three phases of current were
lost. Design: Less than 10% RLA, trip in 2.64 seconds.
This diagnostic will preclude the Phase Loss Diagnostic
and the Transition Complete Input Opened Diagnostic
from being called out. To prevent this diagnostic from
occurring with the intended disconnect of main power,
the minimum time to trip must be greater than the
guaranteed reset time of the Starter module. Note:
All compressor This diagnostic prevents nuisance latching diagnostics
running modes [all due to a momentary power loss – It does not protect
Power Loss Chiller Immediate NonLatch compressor starting motor/compressor from uncontrolled power Remote
and non-running reapplication. See Momentary Power Loss Diagnostic
modes] for this protection. This diagnostic will auto reset in 10
seconds from its occurrence, and is not active during
the start mode before the transition complete input is
proven. This prevents the chiller from cycling due to
some internal starter problem, as the starter would
latch out on either a “Starter Fault Type 3” or a “Starter
Did Not Transition” latching diagnostic. However true
power loss occurring during a start would result in a
misdiagnosis and the chiller would not automatically
recover.
A 30% current imbalance has been detected on one
Severe Current
Chiller Normal Latch All Running Modes phase relative to the average of all 3 phases for 90 Local
Imbalance
continuous seconds.
84 RTHD-SVX01G-EN
Diagnostics
Table 34. Starter diagnostics (continued)

Detected compressor currents greater than 10% RLA
on any or all phases when the compressor was
commanded off. Detection time shall be 5 seconds
minimum and 10 seconds maximum. On detection and
Starter Contactor
Starter Immediate until the controller is manually reset: generate
not Energized
Contactor Chiller and Special Latch diagnostic, energize the appropriate alarm relay, Local
[Starter Contactor
Interrupt Failure Action continue to energize the Evap and Cond Pump Outputs,
Energized]
continue to command the affected compressor off, fully
unload the effected compressor. For as long as current
continues, perform liquid level and oil return gas pump
control
The Starter Module did not receive a transition
complete signal in the designated time from its
command to transition. The must hold time from the
Starter Did Not On the first check Starter Module transition command is 1 second. The
Chiller Immediate Latch Local
Transition after transition. Must trip time from the transition command is 6
seconds. Actual design is 2.5 seconds. This diagnostic
is active only for Y-Delta, Auto-Transformer, Primary
Reactor, and X-Line Starters.
While in the Starter Dry Run Mode either 50% Line
Starter Dry Run Starter Dry Run Voltage was sensed at the Potential Transformers or
Test Mode 10% RLA Current was sensed at the Current
Transformers.
This is a specific starter test where 1M(1K1) is closed
first and a check is made to ensure that there are no
Starter Fault Starting - Y Delta
Chiller Immediate Latch currents detected by the CT's. If currents are detected Local
Type I Starters Only
when only 1M is closed first at start, then one of the
other contactors is shorted.
a. This is a specific starter test where the Shorting
Contactor (1K3) is individually energized and a check is
made to ensure that there are no currents detected by
Starter Fault Starting All types of the CT's. If current is detected when only S is energized
Type II starters at Start, then 1M is shorted. b. This test in a. above
applies to all forms of starters (Note: It is understood
that many starters do not connect to the Shorting
Contactor.).
As part of the normal start sequence to apply power to
the compressor, the Shorting Contactor (1K3) and then
Starter Fault Starting [AFD the Main Contactor (1K1) were energized. 1.6 seconds
Type III Starter] later there were no currents detected by the CT's for the
last 1.2 seconds on all three phases. The test above
applies to all forms of starters.
The Transition Complete input is open with the
Transition All Running Modes
compressor motor running after a successful
Complete Input Chiller Immediate Latch after transition Local
completion of transition. This is active only for all
Opened completed
electromechanical starters
Transition The Transition Complete input is shorted before the
Complete Input Chiller Immediate Latch Pre-Start compressor was started. This is active for all Local
Shorted electromechanical starters.
a. Average of all monitored Line voltages below - 10%
of nominal or the Under/Overvoltage transformer(s)
are not connected. [Must hold = - 10% of nominal. Must
trip = - 15% of nominal. Reset differential = min. of 2%
Under Voltage Chiller Normal NonLatch All Remote
and max. of 4%. Time to trip = min. of 1 min. and max.
of 5 min.) Design: Nom. trip: 60 seconds at less than
87.5%, + or - 2.8% at 200V or + or - 1.8% at 575V,
Auto Reset at 90% or greater.
RTHD-SVX01G-EN 85
Diagnostics
Main Processor Diagnostics

Table 35. Main processor diagnostics

Out-Of-Range Low or Hi or bad LLID, set diagnostic. This
AFD output
Chiller Info NonLatch All Info diagnostic will automatically reset if the input returns
power input
to the normal range.
The BAS was setup as “installed” at the MP and the Comm
3 llid lost communications with the BAS for 15 contiguous
minutes after it had been established. Refer to Section on
BAS Setpoint Arbitration to determine how setpoints and
Communication Chiller Special All operating modes may be effected by the comm loss. The Remote
Lost chiller follows the value of the Tracer Default Run
Command which can be previously written by Tracer and
stored nonvolatilely by the MP (either use local or
shutdown).
The BAS was setup as “installed” and the BAS did not
communicate with the MP within 15 minutes after power-
BAS Failed to
up. Refer to Section on Setpoint Arbitration to determine
Establish Chiller Special At power-up Remote
how setpoints and operating modes may be effected. Note:
Communication
The original requirement for this was 2 minutes, but was
implemented at 15 minutes for RTAC.
The real time clock had detected loss of its oscillator at
some time in the past. Check / replace battery. This
Check Clock Chiller Info Latch All diagnostic can be effectively cleared only by writing a new Remote
value to the chiller’s time clock using the Tracer TU or TD7
“set chiller time” functions.
Compressor
Discharge
Chiller Immediate Latch All Bad Sensor or LLID Remote
Temperature
Sensor
Condenser Info and
Bad Sensor or LLID. If chiller running, and condenser water
Entering Water Chiller Special Latch All Remote
regulating valve option installed, force valve to 100% flow.
Temp Sensor Action
Condenser
Leaving Water Chiller Info Latch All Bad Sensor or LLID Remote
Temp Sensor
Condenser Rfgt
Pressure Chiller Normal Latch All Bad Sensor or LLID Remote
Transducer
The condenser water flow proof input was open for more
than 6 contiguous seconds after flow had been proven.
Condenser Start and All Run This diagnostic is automatically cleared once the
Chiller Immediate NonLatch Remote
Water Flow Lost Modes compressor is stopped by a fixed time out of 7 sec. The
Cond Pump shall be commanded off but the Evap pump
command will not be effected.
Condenser water flow was not proven within 20 minutes of
Condenser the condenser pump relay being energized. The Cond
Estab Cond Water
Water Flow Chiller Normal NonLatch Pump shall be commanded off. Diagnostic is reset with Remote
Flow
Overdue return of flow (although only possible with external control
of pump)
a. EMERGENCY STOP input is open. An external interlock
Emergency Stop Chiller Immediate Latch All has tripped. Time to trip from input opening to unit stop Local
shall be 0.1 to 1.0 seconds.
The entering evaporator water temp fell below the leaving
evaporator water temp. by more than 2°F for 100°F-sec.
Evap Water Flow Any Ckt(s)
For falling film evaporators this diagnostic cannot reliably
(Entering Water Chiller Info NonLatch Energized [No Remote
indicate loss of flow, but can warn of improper flow
Temp) Ckt(s) Energized]
direction through the evaporator, misbound temperature
sensors, or other system problems
Bad Sensor or LLID Normal operation unless CHW Reset is
Evaporator Info and enabled. If CHW Reset is enabled and either Return or
Entering Water Chiller Special Latch Constant Return Chilled Water Reset is selected, its effect Remote
Temp Sensor Action will be removed but slew rates on the change will be limited
per the Chilled Water Reset spec.
86 RTHD-SVX01G-EN
Diagnostics
Table 35. Main processor diagnostics (continued)

Evaporator
Leaving Water Chiller Normal Latch All Bad Sensor or LLID Remote
Temp Sensor
Evaporator
Liquid Level Chiller Normal Latch All Bad Sensor or LLID Remote
Sensor
Evaporator Rfgt
Pressure Chiller Normal Latch All Bad Sensor or LLID Remote
Transducer
The Evaporator water flow proof input was open for more
than 6-10 contiguous seconds after flow had been proven.
Evap pump The pump command status will not be effected. Even
Evaporator commanded “on” though the pump may be commanded to run in the STOP
Chiller Immediate NonLatch Remote
Water Flow Lost except for [All Stop modes (pump off delay time), this diagnostic shall not be
modes] called out in the STOP modes. This diagnostic will auto-
clear on proof of flow (6-10 seconds of continuous flow),
or if chiller is returned to Stop mode.
Evaporator water flow was not proven within 20 minutes of
Evaporator Estab. Evap. Water the Evaporator water pump relay being energized. The
Water Flow Chiller Normal NonLatch Flow on going from Evap pump command status will not be effected. This Remote
Overdue STOP to AUTO. diagnostic will auto-clear on proof of flow (6-10 seconds of
continuous flow), or if chiller is returned to Stop mode.
a. Not “Enabled”: no diagnostics. b. “Enabled “: Out-Of-
Info and Range Low or Hi or bad LLID, set diagnostic, default BLS
External Base
Chiller Special NonLatch All to next level of priority (e.g. Front Panel SetPoint. This Info Remote
Loading Setpoint
Action diagnostic will automatically reset if the input returns to
the normal range.
a. Function Not “Enabled”: no diagnostics. b. “Enabled “:
External Chilled/ Out-Of-Range Low or Hi or bad LLID, set diagnostic,
Hot Water Chiller Info NonLatch All default CWS to next level of priority (e.g. Front Panel Remote
Setpoint SetPoint). This Info diagnostic will automatically reset if
the input returns to the normal range.
a. Not “Enabled”: no diagnostics. b. “Enabled “: Out-Of-
Range Low or Hi or bad LLID, set diagnostic, default CLS
External Current
Chiller Info NonLatch All to next level of priority (e.g. Front Panel SetPoint. This Info Remote
Limit Setpoint
diagnostic will automatically reset if the input returns to
the normal range.
The compressor discharge temperature exceeded 190°F.
This diagnostic will be suppressed if it occurs during the
All [compressor not compressor run-unload period or after the compressor has
High Cprsr Rfgt
running or during stopped, but a run unload will be terminated early as a
Discharge Chiller Immediate Latch Remote
compressor run result. Note: As part of the Compressor High Temperature
Temperature
unload] Limit Mode (aka Minimum Capacity Limit), the compressor
shall be forced loaded as the filtered discharge
temperature nears this trip-point.
High Differential a. The system differential pressure was above 160 Psid-
Refrigerant Chiller Normal Latch Chiller Energized trip immediately (normal shutdown) Remote
Pressure b.The diff pressure was above 152 Psid - trip in 1 hour
The liquid level sensor is seen to be at or near its high end
of range for 80 contiguous minutes while the compressor
Starter Contactor
High Evaporator is running. (The diagnostic timer will hold, but not clear
Chiller Normal Latch Energized [all Stop Remote
Liquid Level when the circuit is off). Design: 80% or more of bit count
modes]
corresponding to +21.2 mm or more liquid level for 80
minutes)
The evaporator refrigerant pressure has risen above 190
psig (future use – add “for continuous15 seconds”). The
evaporator water pump relay will be de-energized to stop
High Evaporator Immediate
the pump regardless of why the pump is running. The
Refrigerant Chiller and Special NonLatch All Local
diagnostic will auto reset and the pump will return to
Pressure Action
normal control when the evaporator pressures falls below
185 psig. This diagnostic must shutdown the chiller if it is
running.
RTHD-SVX01G-EN 87
Diagnostics

The leaving water temperature exceeded the high evap
water temp limit (TV service menu settable –default 105F)
for 15 continuous seconds. The evaporator water pump
relay will be de-energized to stop the pump but only if it
Only effective if
is running due one of the diagnostics listed on the right.
either
The diagnostic will auto reset and the pump will return to
1)Evap Wtr Flow
High Evaporator Info and normal control when the temperature falls 5°F below the
Overdue, 2)Evap
Water Chiller Special NonLatch trip setting. The primary purpose is to stop the evaporator Local
Wtr Flow Loss, or
Temperature Action water pump and its associated pump heat from causing
3)Low Evap Rfgt
excessive waterside temperatures and waterside
Temp,-Unit Off,
pressures when the chiller is not running but the evap
diagnostic is active.
pump is on due to either Evap Water Flow Overdue,
Evaporator Water Flow Loss, or Low Evap Temp – Unit Off
Diagnostics. This diagnostic will not auto clear solely due
to the clearing of the enabling diagnostic.
A high pressure cutout was detected; C.O. on rise @ 180
psig, reset @ 135 psig (+/-5 psi on switching tolerance)
Note: Pressure relief valve is 200 Psig +- 2% trip at 315
High Pressure
Chiller Immediate Latch All ± 5 psi. Note: Other diagnostics that may occur as an Local
Cutout
expected consequence of the HPC trip will be suppressed
from annunciation. These include Phase Loss, Power Loss,
and Transition Complete Input Open.
The system pressure ratio exceeded 5.61 for 1 contiguous
High Refrigerant Service Pumpdown minute. This pressure ratio is a fundamental limitation of
Chiller Immediate Latch Remote
Pressure Ratio Only the compressor. The pressure ratio is defined as Pcond
(abs)/Pevap(abs).
The neuron software in the LCI-C module does not match
LCI-C Software the chiller type. Download the proper software into the
Mismatch: Use Chiller info NonLatch All LCI-C neuron. To do this, use the Rover service tool, or a Remote
BAS Tool LonTalk® tool capable of downloading software to a
Neuron 3150®.
Loss of Oil at In running modes, Oil Loss Level Sensor detects lack of oil
Starter Contactor
Compressor Chiller Immediate Latch in the oil tank feeding the compressor (distinguishing a Local
Energized
(Running) liquid flow from a vapor flow)
Oil Loss Level Sensor detects a lack of oil in the oil tank
Loss of Oil at Immediate Compressor Pre-
feeding the compressor for 90 seconds after EXV
Compressor Chiller and Special Latch start [all other Local
preposition is completed. Note: Compressor start is
(Stopped) Action modes]
delayed while waiting for oil to be detected.
The system differential pressure was either below 15 Psid
for more than 164 Psid-sec, or below 23.0 Psid for 3000
Psid-sec. The latter integral’s value is not cleared for any
Low Differential reason including diagnostic trip, manual reset, or power up
Refrigerant Chiller Immediate Latch Chiller Energized reset (ie. Integral is saved nonvolatily on power down). Remote
Pressure The integral will decay while circuit is running at a max rate
of –10 PSID, and while stopped at a rate of –0.4 PSID. This
same integral is associated with the operating mode
“Compressor Cool Down”. Also see diagnostic below
While Running Normally, the Discharge Superheat was less
Low Discharge than 12 degrees F +- 1F for more than 6500 degree F
Chiller Normal Latch Any Running Mode Remote
Superheat seconds. At startup the UCM shall ignore the Discharge
Superheat for 5 minutes.
The liquid level sensor is seen to be at or near its low end
Starter Contactor
Low Evaporator of range for 80 contiguous minutes while the compressor
Chiller Info NonLatch Energized [all Stop Remote
Liquid Level is running. Design: 20% or less of bit count corresponding
modes]
to –21.2 mm or less liquid level for 80 minutes)
The Evaporator Refrigerant Pressure dropped below 10
Low Evaporator psia just prior to compressor start. The pressure fell below
Chiller Prestart and
Refrigerant Chiller Immediate Latch 10 psia while running but before the 3 minute ignore time Local
Chiller Energized
Pressure had expired or fell below 16 Psia after the 3 minute ignore
time had expired.
88 RTHD-SVX01G-EN
Diagnostics

a. The inferred Saturated Evap Refrigerant Temperature
(calculated from suction pressure transducer(s)) dropped
below the Low Refrigerant Temperature Cutout Setpoint
for 450°F-sec (10°F-sec max rate) while the circuit was
running after the ignore period had expired. The integral
is held at zero for the 1 minute ignore time following the
circuit startup and the integral will be limited to never trip
Low Evaporator
All Ckt Running in less than 45 seconds, i.e. the error term shall be
Refrigerant Chiller Immediate Latch Remote
Modes clamped to 10°F. The minimum LRTC setpoint is -5°F (18.7
Temperature
Psia) the point at which oil separates from the refrigerant.
b. During the timeout of the trip integral, the unload
solenoid(s) of the running compressors on the circuit, shall
be energized continuously and the load solenoid shall be
off. Normal load/unload operation will be resumed if the
trip integral is reset by return to temps above the cutout
setpoint.
The evap sat temp fell below the water temp cutout setting
while the respective evap liquid level was greater than –
21.2mm for 30 (or 150 beginning with rev 08) degree F
Unit in Stop Mode,
Info and seconds while Chiller is in the Stop mode, or in Auto mode
Low Evaporator or in Auto Mode and
Chiller Special NonLatch with no compressors running. Energize Evap Water pump Remote
Temp: Unit Off No Ckt's Energizd
Action Relay until diagnostic auto resets, then return to normal
[Any Ckt Energizd]
evap pump control. Automatic reset occurs when either
the evap temp rises 2°F (1.1°C) above the cutout setting
or the liquid level falls below –21.2mm for 30 minutes.
The leaving Evaporator water temp. fell below the leaving
water temp cutout setting for 30°F-seconds while the
Unit in Stop Mode,
Low Evaporator Info and Chiller is in the Stop mode, or in Auto mode with no
or in Auto Mode and
Water Temp Chiller Special NonLatch compressors running. Energize Evap Water pump Relay Remote
No Ckt(s) Energized
(Unit Off) Action until diagnostic auto resets, then return to normal evap
[Any Ckt Energized]
pump control. Automatic reset occurs when the temp rises
2°F (1.1°C) above the cutout setting for 30 minutes.
The Evaporator water temp. fell below the cutout setpoint
for 30 degree F Seconds while the compressor was
Low Evaporator Immediate Any Ckt[s]
running. Automatic reset occurs when the temperature
Water Temp Chiller and Special NonLatch Energized [No Remote
rises 2°F (1.1°C) above the cutout setting for 2 minutes.
(Unit On) Action Ckt(s) Energizd]
This diagnostic shall not de-energize the Evaporator Water
Pump Output.
The oil pressure was out of the acceptable pressure range
for 15 seconds, while the Delta Pressure was greater than
Chiller Energized
15 Psid.: Acceptable range is 0.50 or 0.60 > (PC-Po) / (PC-
Low Oil Flow Chiller Immediate Latch and Delta P above Local
PE) for the first 2.5 minutes of operation, and 0.40 or 0.50
15 Psid
> (PC-Po) / (PC-PE) thereafter. The higher ratios used if the
system DP is less than 23 psid
MP: Could not MP has determined there was an error with the previous
Store Starts and None Info Latch All power down store. Starts and Hours may have been lost for Remote
Hours the last 24 hours.
MP: Invalid MP has an invalid configuration based on the current
None Immediate Latch All Remote
Configuration software installed
MP: Non-Volatile MP has determined there was an error with a block in the
None Info Latch All Remote
Block Test Error Non-Volatile memory. Check settings.
MP: Non-Volatile MP has determined there was an error in a sector of the
Memory None Info Latch All Non-Volatile memory and it was reformatted. Check Remote
Reformat settings.
The main processor has successfully come out of a reset
and built its application. A reset may have been due to a
MP: Reset Has power up, installing new software or configuration. This
Chiller Info NonLatch All Remote
Occurred diagnostic is immediately and automatically cleared and
thus can only be seen in the Historic Diagnostic List in
Tracer TU.
The system differential pressure was below 7.7 Psid. The
No Differential
occurrence of this diagnostic will saturate the above “Low
Refrigerant Chiller Immediate Latch Chiller Energized Remote
Diff Rfgt Press” Integral and invoke the same “Compressor
Pressure
Cool Down” op mode.
RTHD-SVX01G-EN 89
Diagnostics

The Oil Pressure Transducer for this Chiller is reading a
Starter Contactor
Oil Flow pressure either above its Condenser Pressure by 15 Psia or
Chiller Immediate Latch Energized [all Stop Local
Protection Fault more, or below its Evaporator Pressure 10 Psia or more for
modes]
30 seconds continuously.
Oil Pressure
Chiller Normal Latch All Bad Sensor or LLID Remote
Transducer
Outdoor Air Info and Bad Sensor or LLID. This diagnostic will only occur if OA
Temperature Chiller Special Latch All sensor is configured.OA Chilled water reset will be Remote
Sensor Action suspended if selected and Tracer OA unavailable.
Refrigerant Open or Shorted input and the Rfgt Monitor is setup as
Chiller Info NonLatch All –if installed Remote
Monitor Input installed
The Restart Inhibit was invoked on a compressor. This
Restart Inhibit Chiller Info NonLatch All indicates excessive chiller cycling which should be Remote
corrected.
A high level software watchdog has detected a condition in
which there was a continuous 5 minute period of
compressor operation, with neither chilled water flow nor
Software Error
Latch – power a” contactor interrupt failure” diagnostic active. The
Number: 1001 All
Immediate down reset is All occurrence of this software error message suggests an Local
Call Trane functions
reqd internal software state chart misalignment has occurred.
Service
The events that led up to this failure, if known, should be
recorded and transmitted to Trane Controls Engineering –
(SW rev 6 and higher)
Starter Failed to Starter failed to arm or start within the allotted time (2
Chiller Info Latch All Remote
Arm/Start minutes).
Starter Module
Checksum on RAM copy of the Starter LLID configuration
Memory Error Chiller Info Latch All Local
failed. Configuration recalled from EEPROM.
Type 1
Starter Module
Checksum on EEPROM copy of the Starter LLID
Memory Error Chiller Immediate Latch All Local
configuration failed. Factor default values used.
Type 2 -
All Cprsr Running
The Starter module status reported back that it is stopped
Unexpected modes, Starting,
when it should be running and no Starter diagnostic exists.
Starter Chiller Normal Nonlatch Running and NA
This diagnostic will be logged in the active buffer and then
Shutdown Preparing to
cleared.
Shutdown
90 RTHD-SVX01G-EN
Diagnostics
Communication Diagnostics
Notes:
• The following communication loss diagnostics will not LLIDs, such as the Quad Relay LLID, have more than
occur unless that input or output is required to be one functional output associated with it. A comm loss
present by the particular configuration and installed with such a multiple function board, will generate
options for the chiller. multiple diagnostics. Refer to the Chiller's wiring
• Communication diagnostics (with the exception of diagrams to relate the occurrence of multiple
“Excessive Loss of Comm” are named by the communication diagnostics back to the physical LLID
Functional Name of the input or output that is no boards that they have been assigned to (bound).
longer being heard from by the Main Processor. Many
Table 36. Communication diagnostics
Active Modes
[Inactive Reset
Diagnostic Name Affects Severity Persistence Modes] Criteria Level
Loss of comm with 20% or more of the llids configured
for the system has been detected. This diagnostic will
Excessive Loss of Comm Chiller Immediate Latch All suppress the callout of all subsequent comm loss Remote
diagnostics. Check power supply(s) and power
disconnects – troubleshoot LLIDS buss using Tracer TU
Comm Loss: Slide Valve Continual loss of communication between the MP and
Chiller Normal Latch All Remote
Unload the Functional ID has occurred for a 30 second period.
Comm Loss: Slide Valve Continual loss of communication between the MP and
Load the Functional ID has occurred for a 30 second period.
Comm Loss: External Auto/ Continual loss of communication between the MP and
Stop the Functional ID has occurred for a 30 second period.
Comm Loss: Emergency Continual loss of communication between the MP and
Stop the Functional ID has occurred for a 30 second period.
Continual loss of communication between the MP and
Comm Loss: External Ice the Functional ID has occurred for a 30 second period.
Normal Latch All Remote
Building Command Chiller shall revert to normal (non-ice building) mode
regardless of last state.
Comm Loss: Ice Building the Functional ID has occurred for a 30 second period.
Status Relay Chiller shall revert to normal (non-ice building) mode
regardless of last state.
the Functional ID has occurred for a 30 second period.
Info and
Comm Loss: Outdoor Air Note that if this diagnostic occurs, Chiller shall remove
Chiller Special Latch All Remote
Temperature any OA Chilled Water Reset, if it was in effect and if
Action
Tracer OA was unavailable. Apply slew rates per Chilled
Water Reset spec
Comm Loss: Evap Leaving Continual loss of communication between the MP and
Water Temp the Functional ID has occurred for a 30 second period.
Info and the Functional ID has occurred for a 30 second period.
Comm Loss: Evap Entering
Special Latch All Chiller shall remove any Return or Constant Return Remote
Water Temp
Action Chilled Water Reset, if it was in effect. Apply slew rates
per Chilled Water Reset spec.
Comm Loss: Condenser Continual loss of communication between the MP and
Info Latch All Remote
Leaving Water Temp the Functional ID has occurred for a 30 second period.
Info and
Comm Loss: Condenser the Functional ID has occurred for a 30 second period.
Special Latch All Remote
Entering Water Temp If chiller running, and condenser water regulating valve
Action
option installed, force valve to 100% flow.
Comm Loss: Cprsr Continual loss of communication between the MP and
Immediate Latch All Remote
Discharge Rfgt Temp the Functional ID has occurred for a 30 second period.
Comm Loss: Ext Chilled/Hot
Special Latch All Chiller shall discontinue use of the External Chilled Remote
Water Setpoint
Action Water Setpoint source and revert to the next higher
priority for setpoint arbitration
RTHD-SVX01G-EN 91
Diagnostics
Table 36. Communication diagnostics (continued)
Active Modes
[Inactive Reset
Comm Loss: Ext Current
Special Latch All Chiller shall discontinue use of the External Current Remote
Limit Setpoint
Action limit setpoint and revert to the next higher priority for
Current Limit setpoint arbitration
Comm Loss: High Pressure Continual loss of communication between the MP and
Cutout Switch the Functional ID has occurred for a 30 second period.
Comm Loss: Evaporator Continual loss of communication between the MP and
Immediate Latch All Remote
Water Flow Switch the Functional ID has occurred for a 30 second period.
Chiller Immediate Latch All Remote
Water Flow Switch the Functional ID has occurred for a 30 second period.
Rfgt Pressure the Functional ID has occurred for a 30 second period.
Rfgt Pressure the Functional ID has occurred for a 30 second period.
Comm Loss: Oil Pressure Chiller Normal Latch All Remote
Comm Loss: Oil Return Gas Continual loss of communication between the MP and
Pump Fill the Functional ID has occurred for a 30 second period.
Comm Loss: Oil Return Gas Continual loss of communication between the MP and
Pump Drain the Functional ID has occurred for a 30 second period.
Comm Loss: Oil Loss Level Continual loss of communication between the MP and
sensor Input the Functional ID has occurred for a 30 second period.
Comm Loss: Master Oil Line Continual loss of communication between the MP and
SV the Functional ID has occurred for a 30 second period.
Water Pump Relay the Functional ID has occurred for a 30 second period.
Water Pump Relay the Functional ID has occurred for a 30 second period.
Comm Loss: SSS/AFD Fault Info Latch All Remote
Comm Loss: Refrigerant Continual loss of communication between the MP and
Monitor Input the Functional ID has occurred for a 30 second period.
Info and
Comm Loss: Ext Base the Functional ID has occurred for a 30 second period.
Loading Setpoint The external base load setpoint input is removed from
Action
the arbitration to establish the Base Loading Setpoint.
Info and
Comm Loss: Ext Base the Functional ID has occurred for a 30 second period.
Loading Command The external base load input is removed from the
Action
arbitration to enable Base Loading.
Rfgt Liquid Level the Functional ID has occurred for a 30 second period.
Comm Loss: Starter Chiller Immediate Latch All Local
Comm Loss: Electronic Continual loss of communication between the MP and
Expansion Valve 1 the Functional ID has occurred for a 30 second period.
Comm Loss: Electronic Continual loss of communication between the MP and
Expansion Valve 2 the Functional ID has occurred for a 30 second period.
Starter Comm Loss: Main Starter has had a loss of communication with the MP for
Chiller Immediate Latch All Local
Processor a 15 second period.
Info and Continual loss of communication between the MP and
Comm Loss: Local BAS
Chiller Special Latch All the Functional ID has occurred for a 30 second period. Remote
Interface
Action Use the last values sent from BAS
Comm Loss: Op Status Continual loss of communication between the MP and
Programmable Relays the Functional ID has occurred for a 30 second period.
Comm Loss: Compressor % Continual loss of communication between the MP and
RLA Output the Functional ID has occurred for a 30 second period.
92 RTHD-SVX01G-EN
Diagnostics
Table 36. Communication diagnostics (continued)
Active Modes
[Inactive Reset
Comm Loss: Cond Rfgt Continual loss of communication between the MP and
Normal All Remote
Pressure Output the Functional ID has occurred for a 30 second period.
Comm Loss: Cond Head Continual loss of communication between the MP and
Press Cntrl Output the Functional ID has occurred for a 30 second period.
Comm Loss: AFD speed Continual loss of communication between the MP and
signal output the Functional ID has occurred for a 30 second period.
Comm Loss: AFD output Continual loss of communication between the MP and
power input the Functional ID has occurred for a 30 second period.
Comm Loss: External Hot Warning Continual loss of communication between the MP and
Chiller Info All Remote
Water Command Reset the Functional ID has occurred for a 30 second period.
Operator Display Diagnostics and Messages

Table 37. Operator display diagnostics and messages
Description
Operator Display Message //Troubleshooting
• Ethernet cable not connected between display and UC800.
• UC800 not powered.
Communication Lost with UC800
• UC800 has an invalid configuration – Download a valid configuration
• UC800 is in Binding View. When exit Binding View, select ‘Restart’ on this message.
• Ethernet cable not connected between display and UC800.
• UC800 not powered.
Display Failed to Establish Communication • UC800 just has the backup application running as received from the vendor. Download CTV
application software.
• UC800 has an invalid configuration – Download a valid configuration
• The display is low on memory, and needs to re-start. Select Yes to restart. Selecting Yes will not
Display is about to Restart
affect the UC800 operation. Only the Operator Display is reset.
File Not Found Update UC800 software with Tracer TU.
Screen partially populated. 
Valid configuration is not present. Download a configuration.
Auto and Stop button graphics display, no text.
Screen Unresponsive TU is downloading software. Wait till download is complete.
• Most likely this UC800 has only the backup application. Download the latest UC 800 software
build.
• This could also mean that the UC800 does not have a valid configuration. Download a
The Page Cannot be found
configuration to it.
• Cycle power to the OD and UC800.
• UC could be in binding view. If so, get it out of binding view by navigating to another screen in TU.
UC800 Configuration is Invalid Update the UC800 configuration with TU.
RTHD-SVX01G-EN 93
Wiring
Table 38 and Table 39 provide lists of field wiring
diagrams, electrical schematics and connection diagrams
for the Optimus™ units. The complete unit wiring package
is documented in RTHD-SVE01*-EN. A laminated wiring
diagram kit is also shipped with each RTHD unit.
To determine the specific electrical characteristics of a
particular chiller, see the nameplates mounted on the
units.
Table 38. Wiring drawings — wye-delta units

Drawing Description
2309-7552 Schematic
2309-7553 Schematic
2309-7554 Schematic
2309-7555 Schematic
2309-7564 Component Location
2309-4870 Field Wiring
2309-4869 Field Layout
Table 39. Wiring drawings — AFD units
Drawing Description
2311-1975 Schematic
2311-1977 Component Location
2311-1976 Field Wiring
2311-0023 Field Layout
94 RTHD-SVX01G-EN
Log and Check Sheets
The operator log and check sheet are included for use as
appropriate, for installation completion verification before
Trane start-up is scheduled, and for reference during the
Trane start-up.
Where the log or check sheet also exists outside of this
publication as standalone literature, the literature order
number is also listed.
• Optimus™ RTHD Installation Completion Check Sheet
and Request for Trane Service (RLC-ADF005*-EN)
• Chiller Settings
• Operator Log
RTHD-SVX01G-EN 95
Log and Check Sheets
Page left intentionally blank
96 RTHD-SVX01G-EN
Optimus™ Model RTHD Chiller 
Installation Completion Check Sheet and Request for Trane Service
Important: A copy of this completed form must be submitted to the Trane service agency that will be responsible for the start-
up of the chiller. Start-up will NOT proceed unless applicable items listed in this form have been satisfactorily
completed. See unit IOM RTHD-SVX01*-EN for detailed installation instructions.
To: Trane Service Office:

S.O. Number: Serial Numbers:
Job/Project Name:
Address:
The following items are being installed and will be completed by:
Important: Start-up must be performed by Trane or an agent of Trane specifically authorized to perform start-up of Trane®
products. Contractor shall provide Trane (or an agent of Trane specifically authorized to perform start-up) with
notice of the scheduled start-up at least two weeks prior to the scheduled start-up.
Important: It is required that heaters are energized for a minimum of 24 hours prior to start up. Therefore, chiller
should have power for this amount of time before Trane Service arrives to do start-up.
Check boxes if the task is complete or if the answer is “yes.”
1. Screw Chiller
 Installation meets foundation requirements.
 In place and piped.
 Isolation pads installed.
2. Piping
Note: See bulletin RLC-PRB015*-EN for piping installation considerations affecting sound.
Chilled water piping connected to:
 Evaporator
 Air handling units
 Pumps
 Flow switch or flow proving device installed (if not factory provided)
 Strainer installed and cleaned
Condenser and heat recovery condenser (as applicable) piping connected to:
 Condenser
 Pumps
 Flow switch or flow proving device installed (if not factory provided)
 Cooling tower
 Heating loop (as applicable)
 Make-up water connected to cooling tower
 Water supply connected to filling system
 Does unit have freeze inhibitor? If unit has freeze inhibitor:
 Verify type and concentration correct per unit submittal
 Calculate and record freeze point of the solution: _____________________________
 Systems filled
 Pumps run, air bled from system
 Strainer installed in entering water piping (evaporator and condenser) and cleaned
 Relief valve ventilation piping installed (if applicable)
3. Flow balancing valves installed

 Leaving chilled water
 Leaving condenser water
 Proper porting to measure flow and balance
 Optional heat recovery or auxiliary condenser water (if applicable)
RLC-ADF005C-EN 1
4. Gauges, thermometers, and air vents
 Installed on both sides of evaporator
 Installed on both sides of condenser and heat recovery condenser (as applicable)
5. Wiring
 Wire size per submittal and NEC 310-16.
 Full power available
 External interlocks (flow switch, pumps auxiliary, etc.)
 Chilled water pump (connected and tested)
 Condenser water pump (connected and tested)
 Cooling tower fan rotation checked
 Heat recovery condenser water pump (as applicable)
 115 Vac power available for service tools as required
 All controls installed and connected
6. Testing
 Dry nitrogen available for pressure testing
 Trace gas amounts of R-134a available for leak testing, if necessary
7.  Refrigerant on job site
8.  Systems can be operated under all actual load conditions
9. Heaters
 Energize oil sump and compressor heaters and verify they are operational using a temperature probe.
 If unit was factory charged (model number digit 35 = A), energize heaters for 24 hours prior to start up.
Important: It is required that heaters are energized for a minimum of 24 hours prior to start up.
Therefore, chiller should have power for this amount of time before Trane Service arrives
to do start-up.
 If unit has nitrogen charge (model number digit 45 = 1), contact Trane Service for unit charging prior to start-up.
10. Equipment room

 Does the equipment room have a refrigerant monitor/sensor capable of monitoring and alarming within the allowable
exposure level of the refrigerant?
 Does the installation have properly placed and operating audible and visual refrigerant alarms?
 Does the equipment room have proper mechanical ventilation?
 If it is required by local code, is a self-contained breathing apparatus available?
11. Owner awareness

 Does the owner have a copy of the MSDS for refrigerant?
2 RLC-ADF005C-EN
Note: Additional time required to properly complete the start-up and commissioning, due to any incompleteness of the
installation, will be invoiced at prevailing rates.
This is to certify that the Trane® equipment has been properly and completely installed, and that the applicable items listed above
have been satisfactorily completed.
Important: It is required that the chiller heaters are energized for a minimum of 24 hours prior to start up. Therefore, the chiller
should have power for this amount of time before Trane Service arrives to do start-up of the equipment.
Checklist completed by: ______________________________________________________________________________________________
Signed: _____________________________________________________________________ Date: _______________________________
In accordance with your quotation and our purchase order number __________________, we will therefore require the presence
of Trane service on this site, for the purpose of start-up and commissioning, by __________________ (date).
Note: Minimum two-week advance notification is required to allow scheduling of the chiller start-up.
Additional comments/instructions: ____________________________________________________________________________________

_____________________________________________________________________________________________________________________
_____________________________________________________________________________________________________________________
_____________________________________________________________________________________________________________________
_____________________________________________________________________________________________________________________
_____________________________________________________________________________________________________________________
_____________________________________________________________________________________________________________________
_____________________________________________________________________________________________________________________
_____________________________________________________________________________________________________________________
_____________________________________________________________________________________________________________________
_____________________________________________________________________________________________________________________
_____________________________________________________________________________________________________________________
_____________________________________________________________________________________________________________________
_____________________________________________________________________________________________________________________
_____________________________________________________________________________________________________________________
_____________________________________________________________________________________________________________________
A copy of this completed from must be submitted to the Trane Service Office that will be responsible for start-up of chiller.
RLC-ADF005C-EN 3
Ingersoll Rand (NYSE:IR) advances the quality of life by creating comfortable, sustainable and efficient environments.
Our people and our family of brands—including Club Car®, Ingersoll Rand®, Thermo King® and Trane®—work together
to enhance the quality and comfort of air in homes and buildings; transport and protect food and perishables; and
increase industrial productivity and efficiency. We are a global business committed to a world of sustainable progress
and enduring results. For more information, visit www.ingersollrand.com.
Ingersoll Rand has a policy of continuous product and product data improvement and reserves the right to change design and specifications without notice.
© 2016 Ingersoll Rand All rights reserved

RLC-ADF005C-EN 30 Aug 2016 We are committed to using environmentally
Supersedes RLC-ADF005B-EN (21 Sep 2015) conscious print practices that reduce waste.
Chiller Settings
Settings
Settings Tab
Chiller
Front Panel Chilled Water Setpt (F)
Front Panel Current Limit Setpt (RLA)
Differential to Start (F)
Differential to Stop (F)
Setpoint Source
Feature Settings
Chilled Water Reset
Return Reset Ratio
Return Start Reset
Return Maximum Reset
Outdoor Reset Ratio
Outdoor Start Reset
Outdoor Maximum Reset
Mode Overrides
Evap Water Pump
Cond Water Pump
Expansion Valve Control
Slide Valve Control
Service Pumpdown
Display Settings
Date Format
Date
Time Format
Time of Day
Keypad/Display Lockout
Display Units
Pressure Units
Language Selection
Operator Log
Chiller Log
Run Time
Main Tab 15 min 30 min 1 hr
Chiller Mode
Evap Ent/Lvg Water Temp
Cond Ent/Lvg Water Temp
Active Chilled Water Setpoint (F)
Average Line Current (%RLA)
Active Current Limit Setpoint (%RLA)
Software Type
Software Version
Reports Tab
Evaporator
Evap Entering Water Temperature (F)
Evap Leaving Water Temperature (F)
Evap Sat Rfgt Temp (F)
Evap Rfgt Pressure (psia)
Evap Approach Temp (F)
Evap Water Flow Switch Status
Expansion Valve Position (%)
Expansion Valve Position Steps
Evap Rfgt Liquid Level (in)
Condenser
Cond Entering Water Temperature (F)
Cond Leaving Water Temperature (F)
Cond Sat Rfgt Temp (F)
Cond Rfgt Pressure (psia)
Cond Approach Temp (F)
Cond Water Flow Switch Status
Cond Head Pressure Ctrl Command (%)
Compressor
Compressor Starts
Compressor Run Time
System Rfgt Diff Pressure (psid)
Oil Pressure (psia)
Compressor rfgt Discharge Temp (F)
Discharge Superheat (F)
% RLA L1 L2 L3 (%)
Amps L1 L2 L3 (Amps)
Volts AB BC CA
Ingersoll Rand (NYSE:IR) advances the quality of life by creating comfortable, sustainable and efficient environments.
Our people and our family of brands—including Club Car®, Ingersoll Rand®, Thermo King® and Trane®—work together
to enhance the quality and comfort of air in homes and buildings; transport and protect food and perishables; and
increase industrial productivity and efficiency. We are a global business committed to a world of sustainable progress
and enduring results. For more information, visit www.ingersollrand.com.
Ingersoll Rand has a policy of continuous product and product data improvement and reserves the right to change design and specifications without notice.
© 2016 Ingersoll Rand All rights reserved

RTHD-SVX01G-EN 30 Aug 2016 We are committed to using environmentally
Supersedes RTHD-SVX01F-EN (22 Sep 2015) conscious print practices that reduce waste.

RTHD SVX01G en - 08302016 PDF

Uploaded by

Copyright:

Available Formats

RTHD SVX01G en - 08302016 PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

RTHD SVX01G en - 08302016 PDF

Uploaded by

Copyright:

Available Formats

Installation, Operation,

Optimus™ Water-Cooled Chillers

August 2016 RTHD-SVX01G-EN

Indicates a potentially hazardous

Important Environmental Concerns • Before installing/servicing this unit, technicians

© 2016 Ingersoll Rand All rights reserved RTHD-SVX01G-EN

and the required qualified personnel to operate the

Pre-Start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 Starter Diagnostics . . . . . . . . . . . . . . . . . . . .83

Figure 1. Typical unit nameplate

Digit 37 – Flow Switch Digit 45 – Under/Over Voltage Digits 54 – Refrigerant Monitor

Control Panel Oil Separator

Gas Pump Condenser

Figure 3. Component location — Optimus™ with AFD (front view)(a)

Figure 4. Component location — Optimus (back view)(a)

Oil Separators Compressor

Table 1. General data

Table 2. General data

Table 3. General data

Loose Parts Inventory

Table 4. Installation requirements

Shipping Weight Operating Weight

Table 6. Weights — units with AFD option(a)

Shipping Weight Operating Weight

Figure 5. Service clearances(a)

EGG, DGG, CGG:

Installation Guide Optimus™ Water-Cooled

• Use flexible electrical conduit.

Figure 6. Lifting location point weights and dimensions(a)

Table 7. Lifting weights

Table 7. Lifting weights (continued) (continued)

Table 8. Center of gravity

Unit Wye-Delta Units AFD Units

Figure 7. Rigging configuration(a)

Table 9. Rigging dimensions

Unit Dimension - in (mm)

Table 9. Rigging dimensions (continued)

Unit Dimension - in (mm)

Important: Rigging dimensions given in Table 9 are

Note: If absolutely necessary, the chiller can be pushed or

Alternate Moving Method

2. If there is insufficient surface available on the top of

Water Pressure Drop Data

General Piping Connections

Figure 14. Condenser and evaporator waterboxes — BBB/BCD

IN IN 2 Pass Evap Connection

Figure 15. Condenser and evaporator waterboxes — CEF/CDE/DDE/EDE/DFF/EFF/CFF

Figure 16. Condenser and evaporator waterboxes — DGG/EGG

Making Grooved Pipe Connections

Entering Chilled Water Piping • Pipe strainer

Leaving Chilled Water Piping • Balancing valve

Condenser Water Regulating Valve Water Treatment

Refrigerant Pressure Relief Valve Venting

Table 10. Pressure relief valve data (continued)

Example For Ice Making:

Required! B1, B2 380 174 291 488 1561

Hazardous Voltage w/Capacitors! 230 329 918 1532 4966

Units with AFD Option

Electrical Data Table Information 242 - 292 3764

“across-the- line”) configuration.