Andover Continuum

Infinet II
i2887 Terminal Controllers

The Andover Continuum Infinet II (i2) 887 is a fully programmable,

low cost, general purpose terminal controller. It has all the
power of an Andover Continuum Infinet II controller, but with a
small form factor.
 02

Andover Continuum Infinet II i2887

Terminal Controllers
Features

With its unique mix of three universal

inputs, one Smart Sensor/room sensor
input, four triac outputs and one relay
output, the i2887 can be easily configured
to control Heat Pumps, Fan Coils, or AC
units. Use the i2887 for direct control
of fans, staged heating and cooling and
monitoring of room temperature, outside
air temperature, return air temperature or
occupancy status.

The i2887 is compact so it can be installed in

tight locations with three mounting screws; and
its removable terminal connectors allow for easy
servicing.

Product AT A GLANCE While the standard i2887 version uses 24

VAC input power, the i2887-L model accepts
incoming line voltage at 115 or 230 VAC, has an
• Compact Terminal Controller Provides onboard transformer, and the same versatile I/O
Low-cost Fan Coil and Heat Pump Control configuration.
• Three Universal Inputs and One Smart Sensor/
Room Sensor Input Similar to all i2 controllers, the i2887 features
Flash memory and a fast (32-bit) processor for
• Four Form A Triac Outputs, One Form A Relay,
faster scan times, with plenty of additional memory
277 VAC @3A
available for data logging of your critical data.
• Non-Volatile Flash Memory Provides Utmost
Reliability — Stores Both Application Program The i2887 communicates with the entire
and Operating System Andover Continuum Infinet™ RS-485 field
• Flash Memory Allows Easy On-Line bus; i.e., both Andover Continuum InfinetTM
Software Updates and Andover Continuum Infinet II controllers,
and is compatible with Andover ContinuumTM
• Removable Terminal Blocks for Easy
CyberStationTM Version 1.6x or greater. Up to
Serviceability
254 Andover Continuum Infinet devices can be
• View and Modify Information with Optional networked to any Andover Continuum network
Andover Continuum Smart Sensor Display controller.
• Local On-Board Service Port

• Typical Applications:
- Fan Coil Unit
- Heat Pump
- Chilled Beams

Schneider Electric One High Street, North Andover, MA 01845 USA Telephone: +1 978 975 9600 Fax: +1 978 975 9674 www.schneider-electric.com/buildings

SDS-I2887-A4.BU.N.EN.1.2006.0.00.CC
 03

Andover Continuum Infinet II i2887

Terminal Controllers
Features (continued)

Increased Reliability with Flash Memory Dimensional Drawings

The i2887’s non-volatile Flash memory stores your
operating system and application programs, so that
in the event of a power loss, your application will
be restored when power is returned. In addition,
the Flash memory allows for easy upgrades of
your operating system via software downloads,
eliminating the need to swap out proms.

Inputs
The input configuration on the i2887 consists of
three full range Universal inputs that accept voltage
(0-5VDC), digital (on/off), counter signals (up to
4Hz), or temperature signals. The i2887 also offers
a fourth input to support the Andover Continuum 2
Smart Sensor, or any standard room temperature
sensor.

Outputs
The i2887 contains five digital outputs — four Form 3
A Triac-based outputs plus one Form A Relay 1 4
output, capable of switching line voltage.

These outputs can be used separately for on/off or

pulsed control of lighting, heat, and fan units or can i2887 Dimensional Drawing
be configured into Form K Tri-state outputs (2-max)
for bi-directional control of dampers and valves.
(Note: Any two consecutive Triac outputs can be
configured as a Form K output.) All Triac outputs
are ground referenced and rated for AC loads only.

Software Capabilities
The dynamic memory of the i2887 can be allocated
for any combination of programs, scheduling,
alarming, and data logging using the powerful
Andover Plain EnglishTM programming language.
Our object-oriented Plain English language with
2
intuitive keywords provides an easy method to tailor
4
the controller to meet your exact requirements.
Programs are entered into the i2887 using the
Andover Continuum CyberStation. Programs are
then stored in, and executed by, the i2887.

1 3 4

i2887-L-xxx Dimensional Drawing

Schneider Electric One High Street, North Andover, MA 01845 USA Telephone: +1 978 975 9600 Fax: +1 978 975 9674 www.schneider-electric.com/buildings

SDS-I2887-A4.BU.N.EN.1.2006.0.00.CC
 04

Andover Continuum Infinet II i2887

Terminal Controllers
Features (continued)

Programming multiple i2887s is inherently easy Dimensional Drawings

with Plain English. A complete copy of one i2887’s
programs can be loaded directly into other i2887s
without changing any point names or programs.
In addition, channel assignments for the i2887 are
similar to other Andover Infinet devices such as the
i2851 for easy program conversion.

Smart Sensor Interface

The i2887 provides a built-in connection for
Andover Continuum Smart Sensor. The Smart
Sensor provides a 2-character LED display and
a 6-button programmable keypad that enables
operators and occupants to change setpoints, 2
balance VAV boxes, monitor occupancy status, and
turn equipment on and off. An enhanced version 1
of the Smart Sensor is also available with a 4-digit
custom LCD that provides the following icons: PM, 3
%, °, Setpoint, Cool, Heat, CFM, Fan, OA, and SP.
4

i2887-L Closed Class

i2887 i2887-L-xxx

1 Communications Drawing 2 Power Drawing

i2887 i2887-L-xxx

4 Outputs Drawing

Inputs Drawing

Schneider Electric One High Street, North Andover, MA 01845 USA Telephone: +1 978 975 9600 Fax: +1 978 975 9674 www.schneider-electric.com/buildings

SDS-I2887-A4.BU.N.EN.1.2006.0.00.CC
 05

Andover Continuum Infinet II i2887

Terminal Controllers
Specifications

i2887 Terminal Controllers

Electrical Communications Input Protection
Power Communications Interface 24 VAC or 24 VDC temporarily on
i2887: 24 VAC, +10% -15%, Through Andover Continuum Infinet any single channel, ±1000V transients
50/60 Hz or i2887-L-xxx: 115/230 VAC, RS-485 field bus to network controller (Tested according to EN61000-4-4)
+10% -15%, 50/60 Hz Communications Speed Input Resolution
Power Consumption 1200 to 19.2K baud 5.0 mV
i2887: 10 VA Bus Length Input Accuracy
i2887-L-xxx: 32 VA 4,000 ft. (1,220m) standard for ±15mV (±0.56°C from -23°C to +66°C or
i2887-L-xxx-C 32 VA Andover Continuum Infinet, i2 Infilink ±1°F from -10°F to +150°F)
Overload Protection module allows extension to longer
Fused with 1 amp fuse. MOV protected distances and is required after every Outputs
Software Real-Time Clock group of 32 units on the network. 4 single pole single throw (SPST) Form A
Synchronized through Andover Continuum Bus Media Triacs (any two consecutive outputs can be
Infinet by network controller Andover Continuum Infinet: twisted, configured as one Tri-state Form K)
shielded pair, low capacitance cable 1 Form A Relay, 277 VAC @3A
Mechanical Comm. Error Checking Triac Output Rating
Operating Environment International Standard CRC 16 Maximum 0.3A, 24VAC,
32°–120°F (0–49°C), Compatibility: Andover Continuum ±2000V transients
10–95% RH (non-condensing) CyberStation 1.6x or greater (Tested according to EN61000-4-4)
Size Compatibility Minimum: 30 mA AC
i2887: 4.40˝ H x 5.13˝ W x 1.15˝ D Andover Continuum CyberStation Each Triac is ground referenced,
(111H x 130W x 30D) mm 1.6x or greater DC loads not permitted
i2887-L-xxx: 4.40”H x 7.32” Output Accuracy
W x 2.31”D (111H x 186W x 59D) mm Inputs 0.1 sec. for pulse width modulation
Weight 3 Universal inputs: Voltage (0-5.115 VDC);
i2887: 0.5 lbs. (0.23 kg) Temperature -30°F to 230°F (-34°C to
i2887-L-xxx: 1.9 lbs. (0.86 kg) 110°C), Digital (on/off), Counter (up to 4Hz
i2887-L-xxx-C: 2.63 lbs. (1.19 kg) at 50% duty cycle, 125 ms min. pulse
Enclosure Type width). Current input (0 - 20 mA) using
UL Open class, IP 10. external 250 ohm resistor
Flammability rating of UL94-5V 1 Smart Sensor Temperature Input
i2887-L-xxx-C (32°F to 105°F) (0°C to 41°C)
UL Close class, IP20 Input Voltage Range
Flammability rating of UL-94-5V 0-5.115 volts DC
Mounting Input Impedance
Panel mount 10K ohm to 5.120V

Schneider Electric One High Street, North Andover, MA 01845 USA Telephone: +1 978 975 9600 Fax: +1 978 975 9674 www.schneider-electric.com/buildings

SDS-I2887-A4.BU.N.EN.1.2006.0.00.CC
 06

Andover Continuum Infinet II i2887

Terminal Controllers
Specifications (continued)

i2887 Terminal Controllers

Connections User LEDs/Switches Agency Listings
Power Status Indicator LEDs UL/CUL 916, FCC CFR 47 Part 15,
2-position fixed screw terminal connector CPU CPU Active ICES-003, EN55022, AS/NZS 3548,
(i2887-L: 3-position fixed) and VCCI Class A, CE
Communications General
3-position removable screw Memory
terminal connector 512K SRAM, 1MB FLASH
Inputs/Smart Sensor Processor
7-position removable screw Motorola 32-bit Coldfire
terminal connector
Outputs User LEDs/Switches
6-position removable screw terminal i2887: Power: 24 VAC
connector (i2887-L: 8-position) i2887-L-115: Power: 115 VAC
Relay i2887-L-230: Power: 230 VAC
2-position fixed screw i2887-L-115-C: Power: 115
Service Port VAC-Closed Class
4-position connector i2887-L-230-C: Power: 230
VAC-Closed Class
Note: i2887-L models provide onboard
24 VAC @750 mA for external loads.

© 2006-2009 Schneider Electric. All rights reserved.

All brand names, trademarks and registered trademarks are the property of their respective owners. Information contained within this document is subject to change
without notice.
On October 1st, 2009, TAC became the Buildings Business of its parent company Schneider Electric. This document reflects the visual identity of Schneider Electric,
however there remains references to TAC as a corporate brand in the body copy. As each document is updated, the body copy will be changed to reflect appropriate
corporate brand changes.
Schneider Electric One High Street, North Andover, MA 01845 USA Telephone: +1 978 975 9600 Fax: +1 978 975 9674 www.schneider-electric.com/buildings

SDS-I2887-A4.BU.N.EN.1.2006.0.00.CC January 2006 pdw