MATERIAL SAFETY DATA SHEET

Prepared to U.S. OSHA, CMA, ANSI and Canadian WHMIS Standards

1. PRODUCT IDENTIFICATION

CHEMICAL NAME; CLASS: HYDROGEN IN ARGON/HELIUM/NITROGEN OR AIR GAS

MIXTURE
TRADE NAMES: None
CHEMICAL FAMILY: Hydrogen/Inert Gas or Air Mixture PRODUCT USE: Calibration Gas
MANUFACTURER
MATHESON TRI-GAS, INC.
150 ALLEN ROAD, Ste 302
BASKING RIDGE, NJ 07920
USA
Phone: 973/257-1100
EMERGENCY PHONE: CHEMTREC (U.S. DOMESTIC): 1-800-424-9300
CHEMTREC INTERNATIONAL: 1-703-527-3887
CANUTEC (CANADA): 1-613-996-6666
NOTE: All WHMIS required information is included. It is located in appropriate sections based on the ANSI Z400.1-2004 format. This product has been classified in
accordance with the hazard criteria of the CPR and the MSDS contains all the information required by the CPR.

2. HAZARD IDENTIFICATION

EMERGENCY OVERVIEW: Product Description: This is a colorless, odorless, non-flammable gas mixture.
Health Hazards: The main health hazard associated with releases of this gas mixture is asphyxiation by
displacement of oxygen, as each component of this mixture is a simple asphyxiant. Rapid release from the
cylinder can cause frostbite. Rapid release can result in airborne objects which present a physical injury
hazard. Flammability Hazards: This gas mixture is not flammable. A cylinder rupture hazard exists when
this gas mixture, which is under pressure, is subject to heat or flames. Reactivity Hazards: This gas mixture
is not reactive. Environmental Hazards: This gas mixture is not expected to cause significant harm if
released to the environment. Plants and animals in immediate vicinity of a release may experience frostbite.
Emergency Response Considerations: Persons responding to releases of this gas mixture must protect
themselves appropriately.

SYMPTOMS OF OVER-EXPOSURE BY ROUTE OF EXPOSURE: The most significant route of over-exposure

for this product is by inhalation.
INHALATION: High concentrations of this gas mixture can cause an oxygen-deficient environment,
especially if released in a poorly-ventilated area (e.g., an enclosed or confined space). Individuals
breathing such an atmosphere may experience symptoms which include headaches, ringing in ears,
dizziness, drowsiness, unconsciousness, nausea, vomiting, and depression of all the senses. Under
some circumstances of overexposure, death may occur. The effects associated with various levels of
oxygen are as follows:
CONCENTRATION OF OXYGEN OBSERVED EFFECT
12-16% Oxygen: Breathing and pulse rate increase, muscular coordination slightly disturbed.
10-14% Oxygen: Emotional upset, abnormal fatigue, disturbed respiration.
6-10% Oxygen: Nausea, vomiting, collapse, or loss of consciousness.
Below 6%: Convulsive movements, possible respiratory collapse, and death.
WARNING: Exposure to atmospheres containing 8-10% or less oxygen will bring about
unconsciousness without warning and so quickly that individuals cannot help or protect themselves.
Lack of sufficient oxygen may cause serious injury or death.

HYDROGEN, AIR, ARGON, HELIUM, or NITROGEN GAS MIXTURE MSDS EFFECTIVE DATE: MAY 19, 2008
PAGE 1 OF 9 MATH0122
 2. HAZARD IDENTIFICATION (Continued)
CONTACT WITH SKIN or EYES: Contact with rapidly expanding gases (which are released under high
pressure) may cause frostbite. In addition, the sudden release of a pressurized gas (such as may occur
in the event of a valve failure) presents a severe hazard of mechanical injury.
SKIN ABSORPTION: No component of this gas mixture presents a hazard of skin absorption.
HEALTH EFFECTS OR RISKS FROM EXPOSURE: Over-exposure to this gas mixture may cause the
following health effects:
ACUTE: The most significant hazard associated with this gas is inhalation of oxygen-deficient atmospheres.
Airborne objects may cause mechanical injury. Contact with rapidly expanding gases during accidental
release may cause frostbite.
CHRONIC: Chronic exposure to oxygen-deficient atmospheres (below 18% oxygen in air) may affect the
heart and nervous system.
TARGET ORGANS: ACUTE: Respiratory system. CHRONIC: Cardiac system, central nervous system.
HMIS RATING: HEALTH HAZARD = 0 FLAMMABILITY HAZARD= 0 PHYSICAL HAZARD = 0
Hazard Scale: 0 = Minimal 1 = Slight 2 = Moderate 3 = Serious 4 = Severe

3. COMPOSITION and INFORMATION ON INGREDIENTS

(10,000 ppm = 1%)

CHEMICAL NAME CAS # mole %

Hydrogen 1333-74-0 < 1.0 In Air

< 2.93 In Argon
< 8.7 In Helium
< 5.7 In Nitrogen
The balance of this gas mixture consists of one of the following inert gases or Air.
Air (compressed, atmospheric) 132259-10-0 Balance
Argon 7440-37-1
Helium 7440-59-7
Nitrogen 7727-37-9

4. FIRST-AID MEASURES
GENERAL INFORMATION: Remove to fresh air, as quickly as possible. Only trained personnel should
administer supplemental oxygen and/or cardio-pulmonary resuscitation, if necessary. Seek medical
attention immediately if adverse effect continues after removal to fresh air.
SKIN EXPOSURE: If release of this gas mixture has resulted in frostbite, warm affected area slowly. Seek
immediate medical attention.
EYE EXPOSURE: If release of this gas mixture has affected the eyes, seek immediate medical attention.
MEDICAL CONDITIONS AGGRAVATED BY EXPOSURE: Pre-existing respiratory conditions may be
aggravated by overexposure to this gas mixture.
RECOMMENDATIONS TO PHYSICIANS: Administer oxygen. Treat symptoms and eliminate overexposure.

5. FIRE-FIGHTING MEASURES
FLASH POINT: Not applicable.
AUTOIGNITION TEMPERATURE: Not applicable NFPA RATING
FLAMMABILITY
FLAMMABLE LIMITS (in air by volume, %):
Lower (LEL): Not applicable. Upper (UEL): Not applicable.
FIRE EXTINGUISHING MATERIALS: Use extinguishing materials 0
appropriate for surrounding materials involved in the fire. Water 0
HEALTH 0 INSTABILITY
spray should be used to cool fire-exposed containers.
FIRE EXTINGUISHING MATERIALS NOT TO BE USED: None
known.
UNUSUAL FIRE AND EXPLOSION HAZARD: This gas mixture
OTHER
does not burn; however, cylinders, when involved in a fire, may
rupture or burst in the heat of the fire. Hazard Scale: 0 = Minimal 1 = Slight 2 =
Moderate 3 = Serious 4 = Severe

HYDROGEN, AIR, ARGON, HELIUM, or NITROGEN GAS MIXTURE MSDS EFFECTIVE DATE: MAY 19, 2008
PAGE 2 OF 9 MATH0122
 5. FIRE-FIGHTING MEASURES (Continued)
EXPLOSION SENSITIVITY TO MECHANICAL IMPACT: Not sensitive.
EXPLOSION SENSITIVITY TO STATIC DISCHARGE: Not sensitive.
SPECIAL FIRE-FIGHTING PROCEDURES: Incipient fire responders should wear eye protection. Structural
fire fighters must wear Self-Contained Breathing Apparatus and full protective equipment. Immediately cool
the cylinders with water spray from a maximum distance. When cool, move cylinders from fire area if this
can be done without risk to firefighters.

6. ACCIDENTAL RELEASE MEASURES

LEAK RESPONSE: Uncontrolled releases should be responded to by trained personnel using pre-planned
procedures. Proper protective equipment should be used in the event of a significant release from a single
cylinder. Call CHEMTREC (1-800-424-9300) for emergency assistance. Or if in Canada, call CANUTEC
(613-996-6666). Attempt to close the main source valve prior to entering the area. If this does not stop the
release (or if it is not possible to reach the valve), allow the gas to release in-place or remove it to a safe
area and allow the gas to be released there. Monitor the surrounding area for the level of Oxygen. The
atmosphere must have at least 19.5 percent Oxygen before personnel can be allowed in the area without
Self-Contained Breathing Apparatus.

7. HANDLING and USE

WORK PRACTICES AND HYGIENE PRACTICES
Do not eat or drink while handling chemicals.
Be aware of all potential exposure symptoms; exposures to a fatal oxygen-deficient atmosphere could occur
without any significant warning symptoms.
All work operations should be monitored in such a way that emergency personnel can be immediately
contacted in the event of a release.
Workers who handle this gas mixture should wear protective clothing, as listed in Section 8 (Exposure
Controls and Personal Protection).
If ventilation controls are not adequate to provide sufficient oxygen content, proper respiratory protection
equipment should be provided and workers using such equipment should be carefully trained in its
operation and limitations.
Precautions must always be taken to prevent suck-back of foreign materials into the cylinder by using a
check-valve, or vacuum break, since suck-back may cause dangerous pressure changes within the
cylinder.
STORAGE AND HANDLING PRACTICES: Cylinders should be stored upright and be firmly secured to
prevent falling or being knocked-over. Cylinders can be stored in the open, but in such cases, should be
protected against extremes of weather and from the dampness of the ground to prevent rusting. Cylinders
should be stored in dry, well-ventilated areas away from sources of heat or ignition. Do not allow the area
where cylinders are stored to exceed 52°C (125°F).
SPECIAL PRECAUTIONS FOR HANDLING GAS CYLINDERS: Compressed gases can present significant
safety hazards. The following rules are applicable to work situations in which cylinders are being used.
Before Use: Move cylinders with a suitable hand-truck. Do not drag, slide or roll cylinders. Do not drop
cylinders or permit them to strike each other. Secure cylinders firmly. Leave the valve protection cap
(where provided) in-place until cylinder is ready for use.
During Use: Use designated CGA fittings and other support equipment. Do not use adapters. Do not use
oils or grease on gas-handling fittings or equipment. Immediately contact the supplier if there are any
difficulties associated with operating cylinder valve. Never insert an object (e.g. wrench, screwdriver, pry
bar, etc.) into valve cap openings. Doing so may damage valve, causing a leak to occur. Use an
adjustable strap wrench to remove over-tight or rusted caps. Never strike an arc, on a compressed gas
cylinder or make a cylinder part of and electric circuit.
After Use: Close main cylinder valve. Replace valve protection cap. Close valve after each use and when
empty. Mark empty cylinders “EMPTY”.
PROTECTIVE PRACTICES DURING MAINTENANCE OF CONTAMINATED EQUIPMENT: Refer to current
CGA Guidelines for information on protective practices during maintenance of contaminated equipment.

HYDROGEN, AIR, ARGON, HELIUM, or NITROGEN GAS MIXTURE MSDS EFFECTIVE DATE: MAY 19, 2008
PAGE 3 OF 9 MATH0122
 8. EXPOSURE CONTROLS - PERSONAL PROTECTION
VENTILATION AND ENGINEERING CONTROLS: Use with adequate ventilation to ensure compliance with
exposure limits described in this section. Local exhaust ventilation is preferred, because it prevents
dispersion of this gas mixture into the work place by eliminating it at its source. If appropriate, install
automatic monitoring equipment to detect the level of Oxygen.
EXPOSURE LIMITS:
CHEMICAL NAME CAS # EXPOSURE LIMITS IN AIR
ACGIH-TLVs OSHA-STELs NIOSH-RELs NIOSH OTHER
TWA STEL TWA STEL TWA STEL IDLH
ppm ppm ppm ppm ppm ppm ppm ppm
Hydrogen 1333-74-0 1000 NE NE NE NE NE NE NE

The balance of this gas mixture consists of one of the following inert gases or Air.

Air (compressed, 132259-10-0 Compressed air is a mixture of approximately 79% Nitrogen, approximately 21% Oxygen and other trace
atmospheric) gases. No exposure limits are applicable to Air, Nitrogen or Oxygen.
Argon 7440-37-1 There are no specific exposure limits for Argon. Argon is a simple asphyxiant (SA). Oxygen levels should
be maintained above 19.5%.
Helium 7440-59-7 There are no specific exposure limits for Helium. Helium is a simple asphyxiant (SA). Oxygen levels
should be maintained above 19.5%.
Nitrogen 7727-37-9 There are no specific exposure limits for Nitrogen. Nitrogen is a simple asphyxiant (SA). Oxygen levels
should be maintained above 19.5%.

See Section 16 for Definitions of Terms Used.

RESPIRATORY PROTECTION: Maintain the Oxygen level above 19.5% in the workplace. If necessary, use
only respiratory protection authorized in the U.S. Federal OSHA Respiratory Protection Standard (29 CFR
1910.134), or equivalent U.S. State standards and Canadian CSA Standard Z94.4-93. Oxygen levels below
19.5% are considered IDLH by OSHA. In such atmospheres, use of a full-facepiece pressure/demand
SCBA or a full facepiece, supplied air respirator with auxiliary self-contained air supply is required under
OSHA’s Respiratory Protection Standard (1910.134-1998).
EYE PROTECTION: Splash goggles or safety glasses. If necessary, refer to U.S. OSHA 29 CFR 1910.133 or
and the Canadian CSA Standard Z94.3-M1982, Industrial Eye and Face Protectors.
HAND PROTECTION: Wear mechanically-resistant gloves when handling cylinders containing this gas
mixture. If necessary, refer to U.S. OSHA 29 CFR 1910.138, or appropriate Standards of Canada.
BODY PROTECTION: Use body protection appropriate for task. Transfer of large quantities under pressure
may require protective equipment appropriate to the task. If necessary, refer to the OSHA Technical
Manual (Section VII: Personal Protective Equipment) or appropriate Standards of Canada. If a hazard of
injury to the feet exists due to falling objects, rolling objects, where objects may pierce the soles of the feet or
where employee’s feet may be exposed to electrical hazards, use foot protection, as described in U.S.
OSHA 29 CFR 1910.136 and the Canadian CSA Standard Z195-02, Protective Footwear.
ENVIRONMENTAL EXPOSURE CONTROLS: Controls should be engineered to prevent release to the
environment, including procedures to prevent spills, atmospheric release and release to waterways.

9. PHYSICAL and CHEMICAL PROPERTIES

The following information is for Air, a possible main component of this gas mixture:
GAS DENSITY: 0.07493 lb/cu ft (1.2 kg/m3) EVAPORATION RATE (nBuAc = 1): Not applicable.
SPECIFIC GRAVITY (air = 1): 1 FREEZING POINT: -216.2°C (-357.2°F)
SOLUBILITY IN WATER: 0.0292 BOILING POINT( @ 1 atmos.): -194.3°C (-137.8°F)
EXPANSION RATIO: Not applicable. SPECIFIC VOLUME (ft3/lb): 13.346
ODOR THRESHOLD: Not applicable. MOLECULAR WEIGHT: 28.975
VAPOR PRESSURE (psia): Not applicable.
COEFFICIENT WATER/OIL DISTRIBUTION: Not applicable.
The following information is for Argon, a possible main component of this gas mixture:
GAS DENSITY: 0.103 lb/cu ft (1.650 kg/m3) EVAPORATION RATE (nBuAc = 1): Not applicable.
SPECIFIC GRAVITY (air = 1): 1.38 FREEZING POINT: -189.2°C (-308.9°F)
SOLUBILITY IN WATER: 0.056 BOILING POINT( @ 1 atmos.): -185.9°C (-302.6°F)
EXPANSION RATIO: Not applicable. SPECIFIC VOLUME (ft3/lb): 9.71
ODOR THRESHOLD: Not applicable. MOLECULAR WEIGHT: 39.95
VAPOR PRESSURE (psia): Not applicable.
COEFFICIENT WATER/OIL DISTRIBUTION: Not applicable.

HYDROGEN, AIR, ARGON, HELIUM, or NITROGEN GAS MIXTURE MSDS EFFECTIVE DATE: MAY 19, 2008
PAGE 4 OF 9 MATH0122
 9. PHYSICAL and CHEMICAL PROPERTIES (Continued)
The following information is for Helium, a possible main component of this gas mixture:
GAS DENSITY: 0.103 lb/cu ft (1.165 kg/m3) EVAPORATION RATE (nBuAc = 1): Not applicable.
SPECIFIC GRAVITY (air = 1): 0.138 FREEZING POINT: Not applicable.
SOLUBILITY IN WATER: 0.0094 BOILING POINT (@ 1 atmos.): -268.9°C (-452.1°F)
EXPANSION RATIO: Not applicable. SPECIFIC VOLUME (ft3/lb): 97.09
ODOR THRESHOLD: Not applicable. MOLECULAR WEIGHT: 4.00
VAPOR PRESSURE (psia): Not applicable.
COEFFICIENT WATER/OIL DISTRIBUTION: Not applicable.
The following information is for Nitrogen, a possible main component of this gas mixture:
GAS DENSITY: 0.072 lb/cu ft (1.153 kg/m3) EVAPORATION RATE (nBuAc = 1): Not applicable.
SPECIFIC GRAVITY (air = 1): 0.967 FREEZING POINT: -209.9°C (-345.8 °F)
SOLUBILITY IN WATER: 0.023 BOILING POINT( @ 1 atmos.): -195.8°C (-320.4°F)
EXPANSION RATIO: Not applicable. SPECIFIC VOLUME (ft3/lb): 13.89
ODOR THRESHOLD: Not applicable. MOLECULAR WEIGHT: 28.01
VAPOR PRESSURE (psia): Not applicable.
COEFFICIENT WATER/OIL DISTRIBUTION: Not applicable.
The following information is pertinent to this product:
APPEARANCE, ODOR AND COLOR: This gas mixture is colorless and odorless.
HOW TO DETECT THIS SUBSTANCE (warning properties): There are no distinct warning properties of
this gas mixture. In terms of leak detection, fittings and joints can be painted with a soap solution to
detect leaks, which will be indicated by a bubble formation.

10. STABILITY and REACTIVITY

STABILITY: Stable at standard temperatures and pressures.
DECOMPOSITION PRODUCTS: Combustion: None. Hydrolysis: None.
MATERIALS WITH WHICH SUBSTANCE IS INCOMPATIBLE: The Hydrogen component is incompatible
with strong oxidizers, halogen compounds (e.g. bromine, chlorine, fluorine), lithium, Argon trifluoride,
oxygen difluoride. Finely divided platinum and some other metals will cause hydrogen to react
explosively with oxygen in air.
HAZARDOUS POLYMERIZATION: Will not occur.
CONDITIONS TO AVOID: Contact with incompatible materials. Cylinders exposed to high temperatures or
direct flame can rupture or burst.

11. TOXICOLOGICAL INFORMATION

TOXICITY DATA: Argon, Helium, Nitrogen and Hydrogen are simple asphyxiants (SA), which act to displace
oxygen in the environment.
SUSPECTED CANCER AGENT: The components of this gas mixture are not found on the following lists: U.S.
EPA, U.S. NTP, U.S. OSHA, U.S. NIOSH, GERMAN MAK, IARC, or ACGIH, and therefore is not
considered to be, nor suspected to be a cancer-causing agent by these agencies.
IRRITANCY OF PRODUCT: This gas mixture is not irritating to contaminated tissue.
SENSITIZATION TO THE PRODUCT: The components of this product are not known to be skin or respiratory
sensitizers.
REPRODUCTIVE TOXICITY INFORMATION: Listed below is information concerning the effects of the
components of this gas mixture on the human reproductive system.
Mutagenicity: The components of this gas mixture are not reported to cause mutagenic effects in humans.
Embryotoxicity: The components of this gas mixture are not reported to cause embryotoxic effects in humans.
Teratogenicity: The components of this gas mixture are not reported to cause teratogenic effects in humans.
Reproductive Toxicity: The components of this gas mixture are not reported to cause adverse reproductive effects in
humans.
BIOLOGICAL EXPOSURE INDICES (BEIs): Currently, there are no Biological Exposure Indices (BEIs)
determined for the components of this gas mixture.

HYDROGEN, AIR, ARGON, HELIUM, or NITROGEN GAS MIXTURE MSDS EFFECTIVE DATE: MAY 19, 2008
PAGE 5 OF 9 MATH0122
 12. ECOLOGICAL INFORMATION
ENVIRONMENTAL STABILITY: This gas mixture will be dissipated rapidly in well-ventilated areas.
EFFECT OF MATERIAL ON PLANTS or ANIMALS: Any adverse effect on animals would be related to
oxygen deficient environments.
EFFECT OF CHEMICAL ON AQUATIC LIFE: No an adverse effect from this gas mixture on aquatic life is
expected.

13. DISPOSAL CONSIDERATIONS

PREPARING WASTES FOR DISPOSAL: Waste disposal must be in accordance with appropriate Federal,
State, and local regulations. Return cylinders with any residual product to Matheson Tri-Gas. Do not
dispose of locally.

14. TRANSPORTATION INFORMATION

U.S. DEPARTMENT OF TRANSPORTATION REGULATIONS: This product is classified as dangerous
goods, per U.S. DOT regulations, under 49 CFR 172.101.
PROPER SHIPPING NAME: Compressed gases, n.o.s.
(Hydrogen, Argon) or (Hydrogen, Helium) or
(Hydrogen, Nitrogen) or (Hydrogen, Air)
UN IDENTIFICATION NUMBER: UN 1956
HAZARD CLASS NUMBER and DESCRIPTION: 2.2 (Non-Flammable Gas)
PACKING GROUP: Not applicable.
D.O.T HAZARD LABEL: Class 2.2 (Non-Flammable Gas)
NORTH AMERICAN EMERGENCY RESPONSE GUIDEBOOK NUMBER (2004): 126
MARINE POLLUTANT: The components of this gas mixture are not classified by the DOT as a Marine
Pollutants (as defined by 49 CFR 172.101, Appendix B).
SPECIAL SHIPPING INFORMATION: Cylinders should be transported in a secure position, in a well-
ventilated vehicle. The transportation of compressed gas cylinders in automobiles or in closed-body
vehicles present serious safety hazards and should be discouraged.
NOTE: Shipment of compressed gas cylinders which have not been filled with the owner’s consent is a
violation of Federal law [49 CFR, Part 173.301 (b)].
TRANSPORT CANADA TRANSPORTATION OF DANGEROUS GOODS REGULATIONS: This gas mixture
is considered as dangerous goods, per regulations of Transport Canada.
PROPER SHIPPING NAME: Compressed gases, n.o.s.
(Hydrogen, Argon) or (Hydrogen, Helium) or
(Hydrogen, Nitrogen) or (Hydrogen, Air)
HAZARD CLASS NUMBER and DESCRIPTION: 2.2 (Non-Flammable Gas)
UN IDENTIFICATION NUMBER: UN 1956
PACKING GROUP: Not Applicable
HAZARD LABEL: Class 2.2 (Non-Flammable Gas)
SPECIAL PROVISIONS: None
EXPLOSIVE LIMIT AND LIMITED QUANTITY INDEX: 0.12
ERAP INDEX: None
PASSENGER CARRYING SHIP INDEX: None
PASSENGER CARRYING ROAD VEHICLE OR PASSENGER CARRYING RAILWAY VEHICLE
INDEX: 75
NORTH AMERICAN EMERGENCY RESPONSE GUIDEBOOK NUMBER (2004): 126
NOTE: Shipment of compressed gas cylinders via Public Passenger Road Vehicle is a violation of
Canadian law (Transport Canada Transportation of Dangerous Goods Act, 1992).
15. REGULATORY INFORMATION
ADDITIONAL U.S. REGULATIONS:
U.S. SARA REPORTING REQUIREMENTS: No component of this product is subject to the reporting
requirements of Sections 302, 304 and 313 of Title III of the Superfund Amendments and
Reauthorization Act.

HYDROGEN, AIR, ARGON, HELIUM, or NITROGEN GAS MIXTURE MSDS EFFECTIVE DATE: MAY 19, 2008
PAGE 6 OF 9 MATH0122
 15. REGULATORY INFORMATION (Continued)
ADDITIONAL U.S. REGULATIONS:
U.S. SARA THRESHOLD PLANNING QUANTITY: There are no specific Threshold Planning Quantities for
the components of this product. The default Federal MSDS submission and inventory requirement filing
threshold of 10,000 lbs (4,540 kg) therefore applies, per 40 CFR 370.20.
U.S. SARA HAZARD CATEGORIES (SECTION 311/312, 40 CFR 370-21): ACUTE: No; CHRONIC: No;
FIRE: No; REACTIVE: No; SUDDEN RELEASE: Yes
U.S. TSCA INVENTORY STATUS: Components of this product are listed on the TSCA Inventory.
U.S. CERCLA REPORTABLE QUANTITY (RQ): Not applicable.
OTHER U.S. FEDERAL REGULATIONS: Hydrogen is subject to the reporting requirements of Section
112(r) of the Clean Air Act. The threshold quantity for this gas is 10,000 lbs (4,540 kg). Hydrogen is
listed as Regulated Substances in quantities of 10,000 lbs (4,540 kg) or greater, per 40 CFR, Part 68 of
the Risk Management for Chemical Accidental Release. Any process that involves a flammable gas on-
site, in one location, in quantities of 10,000 lbs (4,540 kg) or greater has requirements under the Process
Safety Management of Highly Hazardous Chemicals (29 CFR 1910.119), unless the gas is used as a
fuel.
CALIFORNIA SAFE DRINKING WATER AND TOXIC ENFORCEMENT ACT (PROPOSITION 65): No
component of this product is on the California Proposition 65 lists.
LABELING: Cylinders of this gas mixture should be labeled for precautionary information per the guidelines
of the CGA. Refer to the CGA for further information.
ADDITIONAL CANADIAN REGULATIONS:
CANADIAN DSL/NDSL INVENTORY STATUS: The components of this product are listed on the DSL
Inventory.
OTHER CANADIAN REGULATIONS: Not applicable.
CANADIAN ENVIRONMENTAL PROTECTION ACT (CEPA) PRIORITIES SUBSTANCES LISTS: The
components of this product are not on the CEPA Priorities Substances Lists.
CANADIAN WHMIS CLASSIFICATION AND SYMBOLS: This gas mixture would be categorized as a
Controlled Product, Hazard Class: A (compressed gas). The following symbol is required for WHMIS
compliance for this gas mixture.

16. OTHER INFORMATION

CREATION DATE: May 16, 2008 REVISION DATE: New
REVISION HISTORY: New
MIXTURES: When two or more gases or liquefied gases are mixed, their hazardous properties may combine to create additional,
unexpected hazards. Obtain and evaluate the safety information for each component before you use the mixture. Consult an
Industrial Hygienist or other trained person when you make your safety evaluation of the end product. Remember, gases and liquids
have properties which can cause serious injury or death.
Further information can be found in the following pamphlets published by: Compressed Gas Association Inc. (CGA), 421 Walney Road,
th
5 Floor, Chantilly, VA 20151. Telephone: (703) 788-2700, Fax: (703) 961-1831.
“Safe Handling of Compressed Gases in Containers” (P-1, 1999)
“Safe Handling and Storage of Compressed Gases” (AV-1, 1999)
“Handbook of Compressed Gases” (1992)
PREPARED BY: CHEMICAL SAFETY ASSOCIATES, Inc.
PO Box 3519, La Mesa, CA 91944-3519
(800)441-3365 / (619) 441-3365

HYDROGEN, AIR, ARGON, HELIUM, or NITROGEN GAS MIXTURE MSDS EFFECTIVE DATE: MAY 19, 2008
PAGE 7 OF 9 MATH0122
 DEFINITION OF TERMS
A large number of abbreviations and acronyms appear on a MSDS. Some of these which are commonly used include the following:
CAS #: This is the Chemical Abstract Service Number that uniquely identifies each HAZARDOUS MATERIALS IDENTIFICATION SYSTEM
constituent.
EXPOSURE LIMITS IN AIR: HAZARD RATINGS (continued):
CEILING LEVEL: The concentration that shall not be exceeded during any part of the FLAMMABILITY HAZARD (continued): 1 (Slight Hazard-Materials that must be pre-
working exposure. heated before ignition can occur. Material require considerable pre-heating, under all
DFG MAK Germ Cell Mutagen Categories: 1: Germ cell mutagens which have been ambient temperature conditions before ignition and combustion can occur, Including:
shown to increase the mutant frequency in the progeny of exposed humans. 2: Germ cell Materials that will burn in air when exposed to a temperature of 815.5°C (1500°F) for a
mutagens which have been shown to increase the mutant frequency in the progeny of period of 5 minutes or less; Liquids, solids and semisolids having a flash point at or above
exposed mammals. 3A: Substances which have been shown to induce genetic damage in 93.3°C [200°F] (e.g. OSHA Class IIIB, or; Most ordinary combustible materials [e.g. wood,
germ cells of human of animals, or which produce mutagenic effects in somatic cells of paper, etc.]; 2 (Moderate Hazard-Materials that must be moderately heated or exposed to
mammals in vivo and have been shown to reach the germ cells in an active form. 3B: relatively high ambient temperatures before ignition can occur. Materials in this degree
Substances which are suspected of being germ cell mutagens because of their genotoxic would not, under normal conditions, form hazardous atmospheres in air, but under high
effects in mammalian somatic cell in vivo; in exceptional cases, substances for which there ambient temperatures or moderate heating may release vapor in sufficient quantities to
are no in vivo data, but which are clearly mutagenic in vitro and structurally related to known produce hazardous atmospheres in air, Including: Liquids having a flash-point at or above
in vivo mutagens. 4: Not applicable (Category 4 carcinogenic substances are those with 37.8°C [100°F]; Solid materials in the form of course dusts that may burn rapidly but that
non-genotoxic mechanisms of action. By definition, germ cell mutagens are genotoxic. generally do not form explosive atmospheres; Solid materials in a fibrous or shredded form
Therefore, a Category 4 for germ cell mutagens cannot apply. At some time in the future, it that may burn rapidly and create flash fire hazards (e.g. cotton, sisal, hemp; Solids and
is conceivable that a Category 4 could be established for genotoxic substances with primary semisolids that readily give off flammable vapors.); 3 (Serious Hazard- Liquids and solids
targets other than DNA [e.g. purely aneugenic substances] if research results make this that can be ignited under almost all ambient temperature conditions. Materials in this
seem sensible.) 5: Germ cell mutagens, the potency of which is considered to be so low degree produce hazardous atmospheres with air under almost all ambient temperatures, or,
that, provided the MAK value is observed, their contribution to genetic risk for humans is unaffected by ambient temperature, are readily ignited under almost all conditions,
expected not to be significant. including: Liquids having a flash point below 22.8°C [73°F] and having a boiling point at or
DFG MAK Pregnancy Risk Group Classification: Group A: A risk of damage to the above 38°C [100°F] and below 37.8°C [100°F] [e.g. OSHA Class IB and IC]; Materials that
developing embryo or fetus has been unequivocally demonstrated. Exposure of pregnant on account of their physical form or environmental conditions can form explosive mixtures
women can lead to damage of the developing organism, even when MAK and BAT with air and are readily dispersed in air [e.g., dusts of combustible solids, mists or droplets
(Biological Tolerance Value for Working Materials) values are observed. Group B: of flammable liquids]; Materials that burn extremely rapidly, usually by reason of self-
Currently available information indicates a risk of damage to the developing embryo or fetus contained oxygen [e.g. dry nitrocellulose and many organic peroxides]); 4 (Severe Hazard-
must be considered to be probable. Damage to the developing organism cannot be Materials that will rapidly or completely vaporize at atmospheric pressure and normal
excluded when pregnant women are exposed, even when MAK and BAT values are ambient temperature or that are readily dispersed in air, and which will burn readily,
observed. Group C: There is no reason to fear a risk of damage to the developing embryo including: Flammable gases; Flammable cryogenic materials; Any liquid or gaseous
or fetus when MAK and BAT values are observed. Group D: Classification in one of the material that is liquid while under pressure and has a flash point below 22.8°C [73°F] and a
groups A-C is not yet possible because, although the data available may indicate a trend, boiling point below 37.8°C [100°F] [e.g. OSHA Class IA; Material that ignite spontaneously
they are not sufficient for final evaluation. when exposed to air at a temperature of 54.4°C [130°F] or below [e.g. pyrophoric]).
IDLH-Immediately Dangerous to Life and Health: This level represents a concentration PHYSICAL HAZARD:
from which one can escape within 30-minutes without suffering escape-preventing or 0 (Water Reactivity: Materials that do not react with water. Organic Peroxides: Materials
permanent injury. that are normally stable, even under fire conditions and will not react with water.
LOQ: Limit of Quantitation. Explosives: Substances that are Non-Explosive. Unstable Compressed Gases: No Rating.
MAK: Federal Republic of Germany Maximum Concentration Values in the workplace. Pyrophorics: No Rating. Oxidizers: No “0” rating allowed. Unstable Reactives:
NE: Not Established. When no exposure guidelines are established, an entry of NE is Substances that will not polymerize, decompose, condense or self-react.); 1 (Water
made for reference. Reactivity: Materials that change or decompose upon exposure to moisture. Organic
NIC: Notice of Intended Change. Peroxides: Materials that are normally stable, but can become unstable at high
NIOSH CEILING: The exposure that shall not be exceeded during any part of the workday. temperatures and pressures. These materials may react with water, but will not release
If instantaneous monitoring is not feasible, the ceiling shall be assumed as a 15-minute energy. Explosives: Division 1.5 & 1.6 substances that are very insensitive explosives or
TWA exposure (unless otherwise specified) that shall not be exceeded at any time during a that do not have a mass explosion hazard. Compressed Gases: Pressure below OSHA
workday. definition. Pyrophorics: No Rating. Oxidizers: Packaging Group III; Solids: any material
NIOSH RELs: NIOSH’s Recommended Exposure Limits. that in either concentration tested, exhibits a mean burning time less than or equal to the
PEL-Permissible Exposure Limit: OSHA’s Permissible Exposure Limits. This exposure mean burning time of a 3:7 potassium bromate/cellulose mixture and the criteria for Packing
value means exactly the same as a TLV, except that it is enforceable by OSHA. Group I and II are not met. Liquids: any material that exhibits a mean pressure rise time
The OSHA Permissible Exposure Limits are based in the 1989 PELs and the June, 1993 less than or equal to the pressure rise time of a 1:1 nitric acid (65%)/cellulose mixture and
Air Contaminants Rule (Federal Register: 58: 35338-35351 and 58: 40191). Both the the criteria for Packing Group I and II are not met. Unstable Reactives: Substances that
current PELs and the vacated PELs are indicated. The phrase, “Vacated 1989 PEL,” is may decompose, condense or self-react, but only under conditions of high temperature
placed next to the PEL that was vacated by Court Order. and/or pressure and have little or no potential to cause significant heat generation or
SKIN: Used when a there is a danger of cutaneous absorption. explosive hazard. Substances that readily undergo hazardous polymerization in the
STEL-Short Term Exposure Limit: Short Term Exposure Limit, usually a 15-minute time- absence of inhibitors.); 2 (Water Reactivity: Materials that may react violently with water.
weighted average (TWA) exposure that should not be exceeded at any time during a Organic Peroxides: Materials that, in themselves, are normally unstable and will readily
workday, even if the 8-hr TWA is within the TLV-TWA, PEL-TWA or REL-TWA. undergo violent chemical change, but will not detonate. These materials may also react
TLV-Threshold Limit Value: An airborne concentration of a substance that represents violently with water. Explosives: Division 1.4 – Explosive substances where the explosive
conditions under which it is generally believed that nearly all workers may be repeatedly effect are largely confined to the package and no projection of fragments of appreciable
exposed without adverse effect. The duration must be considered, including the 8-hour. size or range are expected. An external fire must not cause virtually instantaneous
TWA-Time Weighted Average: Time Weighted Average exposure concentration for a explosion of almost the entire contents of the package. Compressed Gases: Pressurized
conventional 8-hr (TLV, PEL) or up to a 10-hr (REL) workday and a 40-hr workweek. and meet OSHA definition but < 514.7 psi absolute at 21.1°C (70°F) [500 psig].
HAZARDOUS MATERIALS IDENTIFICATION SYSTEM HAZARD Pyrophorics: No Rating. Oxidizers: Packing Group II Solids: any material that, either in
RATINGS: This rating system was developed by the National Paint and Coating concentration tested, exhibits a mean burning time of less than or equal to the mean
Association and has been adopted by industry to identify the degree of chemical hazards. burning time of a 2:3 potassium bromate/cellulose mixture and the criteria for Packing
HEALTH HAZARD: Group I are not met. Liquids: any material that exhibits a mean pressure rise time less than
or equal to the pressure rise of a 1:1 aqueous sodium chlorate solution (40%)/cellulose
0 (Minimal Hazard: No significant health risk, irritation of skin or eyes not anticipated. Skin
mixture and the criteria for Packing Group I are not met. Unstable Reactives: Substances
Irritation: Essentially non-irritating. PII or Draize = “0”. Eye Irritation: Essentially non-
that may polymerize, decompose, condense, or self-react at ambient temperature and/or
irritating, or minimal effects which clear in < 24 hours [e.g. mechanical irritation]. Draize =
pressure, but have a low potential for significant heat generation or explosion. Substances
“0”. Oral Toxicity LD50 Rat: < 5000 mg/kg. Dermal Toxicity LD50Rat or Rabbit: < 2000
that readily form peroxides upon exposure to air or oxygen at room temperature); 3 (Water
mg/kg. Inhalation Toxicity 4-hrs LC50 Rat: < 20 mg/L.); 1 (Slight Hazard: Minor reversible
Reactivity: Materials that may form explosive reactions with water. Organic Peroxides:
Injury may occur; slightly or mildly irritating. Skin Irritation: Slightly or mildly irritating. Eye
Materials that are capable of detonation or explosive reaction, but require a strong initiating
Irritation: Slightly or mildly irritating. Oral Toxicity LD50 Rat: > 500-5000 mg/kg. Dermal
source, or must be heated under confinement before initiation; or materials that react
Toxicity LD50Rat or Rabbit: > 1000-2000 mg/kg. Inhalation Toxicity LC50 4-hrs Rat: > 2-20
explosively with water. Explosives: Division 1.2 – Explosive substances that have a fire
mg/L); 2 (Moderate Hazard: Temporary or transitory injury may occur. Skin Irritation:
hazard and either a minor blast hazard or a minor projection hazard or both, but do not
Moderately irritating; primary irritant; sensitizer. PII or Draize > 0, < 5. Eye Irritation:
have a mass explosion hazard. Compressed Gases: Pressure > 514.7 psi absolute at
Moderately to severely irritating and/or corrosive; reversible corneal opacity; corneal
21.1°C (70°F) [500 psig]. Pyrophorics: No Rating. Oxidizers: Packing Group I Solids: any
involvement or irritation clearing in 8-21 days. Draize > 0, < 25. Oral Toxicity LD50 Rat: >
material that, in either concentration tested, exhibits a mean burning time less than the
50-500 mg/kg. Dermal Toxicity LD50Rat or Rabbit: > 200-1000 mg/kg. Inhalation Toxicity
mean burning time of a 3.:2 potassium bromate/cellulose mixture. Liquids: Any material
LC50 4-hrs Rat: > 0.5-2 mg/L.); 3 (Serious Hazard: Major injury likely unless prompt action
that spontaneously ignites when mixed with cellulose in a 1:1 ratio, or which exhibits a mean
is taken and medical treatment is given; high level of toxicity; corrosive. Skin Irritation:
pressure rise time less than the pressure rise time of a 1:1 perchloric acid (50%)/cellulose
Severely irritating and/or corrosive; may destroy dermal tissue, cause skin burns, dermal
mixture. Unstable Reactives: Substances that may polymerize, decompose, condense or
necrosis. PII or Draize > 5-8 with destruction of tissue. Eye Irritation: Corrosive, irreversible
self-react at ambient temperature and/or pressure and have a moderate potential to cause
destruction of ocular tissue; corneal involvement or irritation persisting for more than 21
significant heat generation or explosion.); 4 (Water Reactivity: Materials that react
days. Draize > 80 with effects irreversible in 21 days. Oral Toxicity LD50 Rat: > 1-50
explosively with water without requiring heat or confinement. Organic Peroxides: Materials
mg/kg. Dermal Toxicity LD50Rat or Rabbit: > 20-200 mg/kg. Inhalation Toxicity LC50 4-hrs
that are readily capable of detonation or explosive decomposition at normal temperature
Rat: > 0.05-0.5 mg/L.); 4 (Severe Hazard: Life-threatening; major or permanent damage
and pressures. Explosives: Division 1.1 & 1.2-explosive substances that have a mass
may result from single or repeated exposure. Skin Irritation: Not appropriate. Do not rate
explosion hazard or have a projection hazard. A mass explosion is one that affects almost
as a “4”, based on skin irritation alone. Eye Irritation: Not appropriate. Do not rate as a “4”,
the entire load instantaneously. Compressed Gases: No Rating. Pyrophorics: Add to the
based on eye irritation alone. Oral Toxicity LD50 Rat: < 1 mg/kg. Dermal Toxicity LD50Rat
definition of Flammability “4”. Oxidizers: No “4” rating. Unstable Reactives: Substances
or Rabbit: < 20 mg/kg. Inhalation Toxicity LC50 4-hrs Rat: < 0.05 mg/L).
that may polymerize, decompose, condense or self-react at ambient temperature and/or
FLAMMABILITY HAZARD:
pressure and have a high potential to cause significant heat generation or explosion.).
0 (Minimal Hazard-Materials that will not burn in air when exposure to a temperature of
815.5°C [1500°F] for a period of 5 minutes.);

HYDROGEN, AIR, ARGON, HELIUM, or NITROGEN GAS MIXTURE MSDS EFFECTIVE DATE: MAY 19, 2008
PAGE 8 OF 9 MATH0122
 16. OTHER INFORMATION (Continued)
DEFINITIONS OF TERMS (Continued)
NATIONAL FIRE PROTECTION ASSOCIATION HAZARD NATIONAL FIRE PROTECTION ASSOCIATION HAZARD
RATINGS: RATINGS (continued):
HEALTH HAZARD: 0 (materials that, under emergency conditions, would offer no hazard HEALTH HAZARD (continued): 3 (continued): Materials that, on account of their
beyond that of ordinary combustible materials): Gases and vapors whose LC50 for acute physical form or environmental conditions, can form explosive mixtures with air and are
inhalation toxicity is greater than 10,000 ppm. Dusts and mists whose LC50 for acute readily dispersed in air. Flammable or combustible dusts with a representative
inhalation toxicity is greater than 200 mg/L. Materials whose LD50 for acute dermal diameter less than 420 microns (40 mesh). Materials that burn with extreme rapidity,
toxicity is greater than 2000 mg/kg. Materials whose LD50 for acute oral toxicity is usually by reason of self-contained oxygen (e.g. dry nitrocellulose and many organic
greater than 2000 mg/kg. Materials that are essentially non-irritating to the respiratory peroxides). Solids containing greater than 0.5 percent by weight of a flammable or
tract, eyes and skin. 1 (materials that, under emergency conditions, can cause significant combustible solvent are rated by the closed cup flash point of the solvent. 4 Materials
irritation): Gases and vapors whose LC50 for acute inhalation toxicity is greater than that will rapidly or completely vaporize at atmospheric pressure and normal ambient
5,000 ppm but less than or equal to 10,000 ppm. Dusts and mists whose LC50 for temperature or that are readily dispersed in air and will burn readily: Flammable gases.
acute inhalation toxicity is greater than 10 mg/L but less than or equal to 200 mg/L. Flammable cryogenic materials. Any liquid or gaseous materials that is liquid while
Materials whose LD50 for acute dermal toxicity is greater than 1000 mg/kg but less than under pressure and has a flash point below 22.8°C (73°F) and a boiling point below
or equal to 2000 mg/kg. Materials whose LD50 for acute oral toxicity is greater than 500 37.8°C (100°F) (i.e. Class IA liquids). Materials that ignite when exposed to air, Solids
mg/kg but less than or equal to 2000 mg/kg. Materials that cause slight to moderate containing greater than 0.5 percent by weight of a flammable or combustible solvent are
irritation to the respiratory tract, eyes and skin. 2 (materials that, under emergency rated by the closed cup flash point of the solvent.
conditions, can cause temporary incapacitation or residual injury): Gases and vapors INSTABILITY HAZARD: 0 Materials that in themselves are normally stable, even under
whose LC50 for acute inhalation toxicity is greater than 3,000 ppm but less than or equal fire conditions: Materials that have an estimated instantaneous power density (product of
to 5,000 ppm. Dusts and mists whose LC50 for acute inhalation toxicity is greater than 2 heat of reaction and reaction rate) at 250°C (482°F) below 0.01 W/mL. Materials that do
mg/L but less than or equal to 10 mg/L. Materials whose LD50 for acute dermal toxicity not exhibit an exotherm at temperatures less than or equal to 500°C (932°F) when tested by
is greater than 200 mg/kg but less than or equal to 1000 mg/kg. Materials whose LD50 differential scanning calorimetry. 1 Materials that in themselves are normally stable, but
for acute oral toxicity is greater than 50 mg/kg but less than or equal to 500 mg/kg. Any that can become unstable at elevated temperatures and pressures: Materials that have
liquid whose saturated vapor concentration at 20°C (68°F) is equal to or greater than an estimated instantaneous power density (product of heat of reaction and reaction rate) at
one-fifth its LC50 for acute inhalation toxicity, if its LC50 is less than or equal to 5000 250°C (482°F) at or above 0.01 W/mL and below 10 W/mL. 2 Materials that readily
ppm and that does not meet the criteria for either degree of hazard 3 or degree of undergo violent chemical change at elevated temperatures and pressures: Materials that
hazard 4. Compressed liquefied gases with boiling points between -30°C (-22°F) and - have an estimated instantaneous power density (product of heat of reaction and reaction
55°C (-66.5°F) that cause severe tissue damage, depending on duration of exposure. rate) at 250°C (482°F) at or above 10 W/mL and below 100W/mL. 3 Materials that in
Materials that are respiratory irritants. Materials that cause severe, but reversible themselves are capable of detonation or explosive decomposition or explosive reaction,
irritation to the eyes or are lachrymators. Materials that are primary skin irritants or but that require a strong initiating source or that must be heated under confinement
sensitizers. 3 (materials that, under emergency conditions, can cause serious or before initiation: Materials that have an estimated instantaneous power density (product of
permanent injury): Gases and vapors whose LC50 for acute inhalation toxicity is greater heat of reaction and reaction rate) at 250°C (482°F) at or above 100 W/mL and below 1000
than 1,000 ppm but less than or equal to 3,000 ppm. Dusts and mists whose LC50 for W/mL. Materials that are sensitive to thermal or mechanical shock at elevated
acute inhalation toxicity is greater than 0.5 mg/L but less than or equal to 2 mg/L. temperatures and pressures. 4 Materials that in themselves are readily capable of
Materials whose LD50 for acute dermal toxicity is greater than 40 mg/kg but less than or detonation or explosive decomposition or explosive reaction at normal temperatures
equal to 200 mg/kg. Materials whose LD50 for acute oral toxicity is greater than 5 mg/kg and pressures: Materials that have an estimated instantaneous power density (product of
but less than or equal to 50 mg/kg. Any liquid whose saturated vapor concentration at heat of reaction and reaction rate) at 250°C (482°F) of 1000 W/mL or greater. Materials
20°C (68°F) is equal to or greater than one-fifth its LC50 for acute inhalation toxicity, if its that are sensitive to localized thermal or mechanical shock at normal temperatures and
LC50 is less than or equal to 3000 ppm and that does not meet the criteria for degree of pressures.
hazard 4. Compressed liquefied gases with boiling points between -30°C (-22°F) and -
55°C (-66.5°F) that cause frostbite and irreversible tissue damage. Materials that are
FLAMMABILITY LIMITS IN AIR:
Much of the information related to fire and explosion is derived from the National Fire
respiratory irritants. Cryogenic gases that cause frostbite and irreversible tissue
Protection Association (NFPA). Flash Point - Minimum temperature at which a liquid gives
damage. Materials that are corrosive to the respiratory tract. Materials that are
off sufficient vapors to form an ignitable mixture with air. Autoignition Temperature: The
corrosive to the eyes or cause irreversible corneal opacity. Materials that are corrosive
minimum temperature required to initiate combustion in air with no other source of ignition.
to the skin. 4 (materials that, under emergency conditions, can be lethal): Gases and
LEL - the lowest percent of vapor in air, by volume, that will explode or ignite in the
vapors whose LC50 for acute inhalation toxicity less than or equal to 1,000 ppm. Dusts
presence of an ignition source. UEL - the highest percent of vapor in air, by volume, that will
and mists whose LC50 for acute inhalation toxicity is less than or equal to 0.5 mg/L.
explode or ignite in the presence of an ignition source.
Materials whose LD50 for acute dermal toxicity is less than or equal to 40 mg/kg.
Materials whose LD50 for acute oral toxicity is less than or equal to 5 mg/kg. Any liquid TOXICOLOGICAL INFORMATION:
whose saturated vapor concentration at 20°C (68°F) is equal to or greater than one-fifth Human and Animal Toxicology: Possible health hazards as derived from human data,
its LC50 for acute inhalation toxicity, if its LC50 is less than or equal to 1000 ppm. animal studies, or from the results of studies with similar compounds are presented.
FLAMMABILITY HAZARD: 0 Materials that will not burn under typical fire conditions, Definitions of some terms used in this section are: LD50 - Lethal Dose (solids & liquids)
including intrinsically noncombustible materials such as concrete, stone, and sand: which kills 50% of the exposed animals; LC50 - Lethal Concentration (gases) which kills
Materials that will not burn in air when exposed to a temperature of 816°C (1500°F) for 50% of the exposed animals; ppm concentration expressed in parts of material per million
a period of 5 minutes in according with Annex D. 1 Materials that must be preheated parts of air or water; mg/m3 concentration expressed in weight of substance per volume of
before ignition can occur. Materials in this degree require considerable preheating, air; mg/kg quantity of material, by weight, administered to a test subject, based on their
under all ambient temperature conditions, before ignition and combustion can occur: body weight in kg. Other measures of toxicity include TDLo, the lowest dose to cause a
Materials that will burn in air when exposed to a temperature of 816°C (1500°F) for a symptom and TCLo the lowest concentration to cause a symptom; TDo, LDLo, and LDo,
period of 5 minutes in accordance with Annex D. Liquids, solids and semisolids having or TC, TCo, LCLo, and LCo, the lowest dose (or concentration) to cause lethal or toxic
a flash point at or above 93.4°C (200°F) (i.e. Class IIIB liquids). Liquids with a flash effects. Cancer Information: The sources are: IARC - the International Agency for
point greater than 35°C (95°F) that do not sustain combustion when tested using the Research on Cancer; NTP - the National Toxicology Program, RTECS - the Registry of
Method of Testing for Sustained Combustibility, per 49 CFR 173, Appendix H or the UN Toxic Effects of Chemical Substances, OSHA and CAL/OSHA. IARC and NTP rate
Recommendation on the Transport of Dangerous Goods, Model Regulations (current chemicals on a scale of decreasing potential to cause human cancer with rankings from 1
edition) and the related Manual of Tests and Criteria (current edition). Liquids with a to 4. Subrankings (2A, 2B, etc.) are also used. Other Information: BEI - ACGIH Biological
flash point greater than 35°C (95°F) in a water-miscible solution or dispersion with a Exposure Indices, represent the levels of determinants which are most likely to be observed
water non-combustible liquid/solid content of more than 85 percent by weight. Liquids in specimens collected from a healthy worker who has been exposed to chemicals to the
that have no fire point when tested by ASTM D 92 Standard Test Method for Flash and same extent as a worker with inhalation exposure to the TLV.
Fire Points by Cleveland Open Cup, up to a boiling point of the liquid or up to a ECOLOGICAL INFORMATION:
temperature at which the sample being tested shows an obvious physical change. BCF = Bioconcentration Factor, which is used to determine if a substance will concentrate
Combustible pellets with a representative diameter of greater than 2 mm (10 mesh). in lifeforms which consume contaminated plant or animal matter; EC is the Effect
Solids containing greater than 0.5 percent by weight of a flammable or combustible Concentration in water; EC50 is the Effect Concentration for 50% of the organisms exposed;
solvent are rated by the closed up flash point of the solvent. Most ordinary combustible NOEC is the No Observed Effect Concentration; MATC is the Maximum Acceptable
materials. 2 Materials that must be moderately heated or exposed to relatively high Toxicant Concentration; NOLC is the No Observed Lethal Concentration; TLm = median
ambient temperatures before ignition can occur. Materials in this degree would not threshold limit; Coefficient of Oil/Water Distribution is represented by log Kow or log Koc
under normal conditions form hazardous atmospheres with air, but under high ambient and is used to assess a substance’s behavior in the environment.
temperatures or under moderate heating could release vapor in sufficient quantities to
produce hazardous atmospheres with air: Liquids having a flash point at or above REGULATORY INFORMATION:
37.8°C (100°F) and below 93.4°C (200°F) (i.e. Class II and Class IIIA liquids.) Solid U.S. and CANADA:
materials in the form of powders or coarse dusts of representative diameter between ACGIH: American Conference of Governmental Industrial Hygienists, a professional
420 microns (40 mesh) and 2 mm (10 mesh) that burn rapidly but that generally do not association which establishes exposure limits. This section explains the impact of various
form explosive mixtures in air. Solid materials in fibrous or shredded form that burn laws and regulations on the material. EPA is the U.S. Environmental Protection
rapidly and create flash fire hazards, such as cotton, sisal and hemp. Solids and Agency. NIOSH is the National Institute of Occupational Safety and Health, which is
semisolids that readily give off flammable vapors. Solids containing greater than 0.5 the research arm of the U.S. Occupational Safety and Health Administration (OSHA).
percent by weight of a flammable or combustible solvent are rated by the closed cup WHMIS is the Canadian Workplace Hazardous Materials Information System. DOT
flash point of the solvent. 3 Liquids and solids that can be ignited under almost all and TC are the U.S. Department of Transportation and the Transport Canada,
ambient temperature conditions. Materials in this degree produce hazardous respectively. Superfund Amendments and Reauthorization Act (SARA); the Canadian
atmospheres with air under almost all ambient temperatures or, though unaffected by Domestic/Non-Domestic Substances List (DSL/NDSL); the U.S. Toxic Substance
ambient temperatures, are readily ignited under almost all conditions: Liquids having a Control Act (TSCA); Marine Pollutant status according to the DOT; the Comprehensive
flash point below 22.8°C (73°F) and having a boiling point at or above 37.8°C (100°F) Environmental Response, Compensation, and Liability Act (CERCLA or Superfund);
and those liquids having a flash point at or above 22.8°C (73°F) and below 37.8°C and various state regulations. This section also includes information on the
(73°F) and below 37.8°C (100°F) (i.e. Class IB and IC liquids). precautionary warnings which appear on the material’s package label. OSHA - U.S.
Occupational Safety and Health Administration.

HYDROGEN, AIR, ARGON, HELIUM, or NITROGEN GAS MIXTURE MSDS EFFECTIVE DATE: MAY 19, 2008
PAGE 9 OF 9 MATH0122