2004 Catalog

TABLE OF CONTENTS Helping People Take ActionSM
AUDIBLE & STROBE APPLIANCES

ELECTRONIC HORNS & STROBE HORNS
1-1 Series NS Horn Strobe & NH Horn Appliances
1-2 Series AS Audible Strobe & AH Audible Appliances
1-3 Series HS4 Horn Strobe & Series HS Horn Appliances
1-4 Series MT Multitone & Multitone Strobe Appliances
1-5 Series AMT Multitone & Multitone Strobe Appliances
MINI-HORNS
1-6 Series MIZ Horn
STROBE APPLIANCES
1-7 Series RSS Strobes & RSSP Single & Multi-Candela Strobes & Strobe Plates
CHIMES & CHIME STROBES
1-8 Series CH Electronic Chimes & Chime Strobes
BELLS
1-9 Series 43T AC Vibrating Bells
1-9 Series MB Motor Bells
1-10 Series CVX/CSX Explosion Proof Bells
AC HORN
1-10 Series 31T Electronic Horn
WEATHERPROOF APPLIANCES
1-11 Series AHWP Audibles, Series ASWP Audible Strobes, Series MTWP Multitone Strobes,
Series RSSWP Strobes & Series ET70WP Weatherproof Speaker Strobes
SPEAKER & SPEAKER STROBE APPLIANCES

SPEAKERS & SPEAKER STROBES
2-0 Series E50 NEW
2-1 Series E Low Profile Speakers & Speaker Strobes
2-2 Series ET Speakers & Speaker Strobes
2-3 Series ET Vandal Resistant Speakers & Speaker Strobes
2-4 Series S UL Listed 8” Supervised Speaker & Speaker Strobe
CLUSTER SPEAKERS
2-5 Series STH Cluster & Series STH Cluster with MAX Strobe Speakers
2-6 Series STH Weatherproof Cluster Speaker
2-7 Series STH-MCCH Cluster Speaker with MCCH Strobe
SPEAKER HORN
2-8 Series STH-15S Supervised Speaker Horn
SELF AMPLIFIED SPEAKERS & SPEAKER STROBES
2-9 Series SA-S Supervised Self-Amplified Speakers & Speaker Strobes
SYNC MODULES, POWER SUPPLIES & PULL STATIONS

SYNC MODULES
3-1 Series SM/DSM Sync Modules
POWER SUPPLY
3-2 Series PS-12/24-8CP and PS-12/24-8MP POWERPATH™
MANUAL PULL STATIONS
3-3 Series MPS Manual Pull Stations
273 Branchport Avenue • Long Branch, NJ 07740 • (800) 631-2148 • www.wheelockinc.com
TABLE OF CONTENTS Helping People Take ActionSM
FACILITY COMMUNICATIONS/AUDIO EVACUATION

SAFEPATH®4 MULTI-FUNCTION FACILITY COMMUNICATIONS SYSTEM
4-1 SAFEPATH®4 Multi-Function Facility Communication Systems
4-3 SAFEPATH®4 Audio & Audio/Strobe Boosters
4-4 SAFEPATH®4 2-Zone Class A or 4-Zone Class B Speaker Audio Splitter
4-4A SAFEPATH®4 Addressable Paging Splitter & Telephone Zone Controller
4-4B SAFEPATH®4 Supervised Volume Control
4-5 SAFEPATH®4 Remote Microphone and Remote Microphone Expansion Module
SAFEPATH® SUPERVISED VOICE EVACUATION/AUDIO & PAGING SYSTEM
4-6 SAFEPATH® Dual Circuit System
4-7 SAFEPATH® Multi-Circuit System
4-8 SAFEPATH® Remote Circuit System
4-9 SAFEPATH® Remote Microphones
4-10 SAFEPATH® Modules, Message Kits, & Batteries
4-11 SAFEPATH® & VoiceLink Messages
See Tab 2, pages 2-0 to 2-9, for UL Listed 8”
4-12 VoiceLink Speaker & Speaker Strobes, Cluster Speakers,
4-14 Series NPS Push Stations Horn Speakers & Self Amplified Speaker &
Speaker Strobes
OSHA/INDUSTRIAL
INDUSTRIAL STROBES
5-1 Series MAX Industrial Strobes
INDUSTRIAL SIGNALS
5-2 Series MT & MT Multitone Electronic Signals
5-3 Series WH Remote Strobes
5-3 Series MTH-24 Multitone Horns
5-4 Series AMT & AMT Strobe Multitone Electronic Signals
5-5 Series 43T & Series MB Motor Bells
5-6 Series CVX/CSX Explosion Proof Bells
5-6 Series 31T AC Horn
INDUSTRIAL SIGNALS
5-7 Series Colored Lens Strobes & Speaker Strobes (Amber, Blue, Green and Red)
TELEPHONE SIGNALING & COMMERCIAL AUDIO

6-1 Series UTA Universal Telephone Alerts
6-2 Series PS Telestrobes
6-3 Series CH Chimes & Series WR Warble Telephone Alerts
6-4 Series CA Common Audible Control Units
6-4 Series TB Telbells
6-5 Telephone Relays
6-6 Power Supplies & Charger
ZONE CONTROLLER & COMMERCIAL AUDIO
6-7 Series MZC Zone Controller
6-8 Series ST Paging Speakers & Horns with Transformer
6-9 Self Amplified Paging Horns
6-9 Series VC Wall Mount Volume Controls
TABLE OF CONTENTS SM
Helping People Take Action
6-10 Speaker Mounting Accessories
6-10 PRM-150 Line Level
6-11 AM/FM Tuner
6-11 Microphone
WIRELESS
7-1 Series CCSWH Central Control Station
7-2 Series CCSWH-PORTLT Portable Central Control Station
7-3 Series RCIWH Wireless Remote Controller
7-4 Series HPSS High Power Speaker Stations
7-5 Series CUSTWH Wireless Emergency Warning System Software and Engineering Design
MOUNTING, ACCESSORIES, REFERENCE

ENCLOSURES
8-1 Series EWR, EWP & EN4 Audible Strobe & Strobe Appliance Enclosures
REFERENCE MATERIAL
8-2 Product Dimensions
8-5 Covers & Grilles
8-6 Agency Approvals
8-7 General and Technical Notes
8-8 Installation Instructions & Specification Sheets Reference
Pull Out Mounting Guide
Visit www.wheelockinc.com to obtain:

www.wheelockinc.com
• Latest Catalog Revisions
• Installation and Specification Sheets
• Software Tools
• Literature
• Application and System Design Assistance
• Technical Support

INTRODUCTION Helping People Take ActionSM
Wheelock Fire Alarm Notification Appliance Circuit Products, Stand

Alone or Integrated Facility Safety
Communication Systems
For over 80 years Wheelock has served the needs of commercial, educational,
industrial and government users with the design and manufacture of high quality
communication products including fire alarm notification appliances, voice evacuation,
voice messaging and security systems.
Wheelock’s most popular line of strobes and combination audible and speaker strobes
are designed for ADA applications while meeting the latest requirements of NFPA 72
(National Fire Alarm Code), UFC (Uniform Fire Code),
ANSI 117.1 (American National Standard for Accessible
and Usable Buildings and Facilities), UL Standard 1971
(Signaling Devices for the Hearing Impaired) and UL
Standard 1638 for Indoor/Outdoor use, as well as, UL
Standard 464 (Audible Signaling Devices) and UL
Standard 1480 (Speaker Appliances). These appliances
include the field selectable SPEC1FIRE™ multi-candela
appliances, multi-candela high intensity strobes wall and
ceiling and weatherproof speaker strobes.
To meet the growing demands for integrated systems

to provide protection from new threats that now endanger
people all over the world, Wheelock has introduced a
new addition to the SAFEPATH® family of supervised
facility communications systems, SAFEPATH ® 4.
SAFEPATH ® 4 is the first UL Listed multi-function
supervised system to offer Background Music, Messaging, Emergency Voice
Evacuation and Paging. This economic solution helps to guide people to safety during
fire or other emergencies and warn potential victims of dangerous environmental
conditions or security threats.
Wheelock also provides a broad range

of educational programs, specification/
application assistance, and detailed product
information that is available directly from our
website at www.wheelockinc.com.
If you are involved in solving SAFETY,

SOUND and SECURITY challenges,
Wheelock’s people and products are
ready to help you and the people you
protect take appropriate actions.

CONTACT INFORMA
CONTACT TION
INFORMATION Helping People Take ActionSM
So that we may service you in an efficient manner, we’ve provided this information as a guide
when contacting Wheelock, Inc. for technical support, customer service, sales or other inquiries.
Corporate Office
273 Branchport Avenue
Long Branch, NJ 07740
Phone: (732) 222-6880
Toll Free: (800) 631-2148
Fax: (732) 222-2588
Company Website
www.wheelockinc.com
E-Learning On-Line Training Website

www.wheelocku.com
Customer Service: (800) 631-2148, Option #2

Technical Support: (800) 631-2148, Option #3
Inside Sales/Marketing Support: (800) 631-2148, Option #4
Training: (800) 631-2148, Ext. 6015
Applications Engineering: (800) 631-2148, Ext. 6024 or 6206
Literature Request: (800) 631-2148, Option #7

Helping People Take ActionSM
Series NS Horn Strobes
& Series NH
Description:
Horn Appliances
Series NS Horn Strobes & Series NH Horn Appliances are ideal
for wall mount designs that require 2 wire installation and 2
selectable dBA settings (90 & 95).
Strobe Options:
Single Candela Wall
all: 1575 cd
Multi Candela Field Selectable Wall
all: 15/30/75/110 cd
Features:
• Selectable Continuous Horn or Temporal (Code 3)
• 2 Selectable dBA settings of 90 and 95 dBA in both tones
• Patented Universal Mounting Plate Series NS
• Wall mount
• Synchronize strobe and audible with Wheelock SM, DSM Series NH
Sync Modules or PS-12/24-8CP and PS-12/24-8MP
Power Supplies with built-in sync protocol
Specification and Ordering Information

Model Model Agency Approvals
Order Strobe 24 12 2
Model Number Color Color Mounting Options#
C ode Candela VDC VDC WIRE UL MEA CSFM FM B FP
R ed White
NS-24MCW-FR 9404 15/30/75/110 X - X X - B,D,E,F,G,H,J,N,O,P,R,X X X X X X
NS-24MCW-FW 9405 15/30/75/110 X - X - X B,D,E,F,G,H,J,N,O,P,R,X X X X X X
NS-241575W-FR 7806 15 (75 on Axis) X - X X - B,D,E,F,G,H,J,N,O,P,R,X X X X X X
NS-241575W-FW 7811 15 (75 on Axis) X - X - X B,D,E,F,G,H,J,N,O,P,R,X X X X X X
NS-121575W-FR 7816 15 (75 on Axis) - X X X - B,D,E,F,G,H,J,N,O,P,R,X X X X X X
NS-121575W-FW 7818 15 (75 on Axis) - X X - X B,D,E,F,G,H,J,N,O,P,R,X X X X X X
NH-12/24-R 7449 - X X X X - B,D,E,F,G,H,J,N,O,P,R,X X X X X X
NH-12/24-W 7500 - X X X - X B,D,E,F,G,H,J,N,O,P,R,X X X X X X
#See mounting options pull out guide in

the last section of this binder.
X = Approved
Average RMS Current

Audible Wall Mount Horn Strobe Models
Series NS/NH
NH-12/24 NS-241575W NS-24MCW
24 V D C
@ 24V D C 15/75cd 15cd 30cd 75cd 110cd
24V D C 0.035 0.082 0.061 0.085 0.129 0.167
High (95) dBA
UL max* 0.044 0.104 0.074 0.107 0.184 0.244
24V D C 0.014 0.067 0.049 0.072 0.117 0.154
Low (90) dBA
UL max* 0.018 0.096 0.066 0.101 0.177 0.232
Audible Wall Mount * RMS current ratings are per UL average RMS method. UL max
Series NS/NH current rating is the maximum RMS current within the listed voltage
NH-12/24 Aud/Strobe
12V D C range (16-33v for 24v units). For strobes the UL max current is
@ 12V NS-121575W usually at the minimum listed voltage (16v for 24v units). For
audibles the max current is usually at the maximum listed voltage
12 V D C 0.016 0.160 (33v for 24v units). For unfiltered FWR ratings, see installation
High (89) dBA
UL max* 0.021 0.262 instructions.
12V D C 0.010 0.155

Low (84) dBA
UL max* 0.012 0.257
10/04
273 Branchport Avenue • Long Branch, NJ 07740 • (800) 631-2148 • www.wheelockinc.com 1-1
Series AS Audible Strobe
Helping People Take ActionSM & Series AH Audible
Description:
Appliances
Series AS Audible Strobe & Series AH Audible Appliances are
ideal for 2 wire applications with 3 selectable dBA settings (90, 95,
99) and wall or ceiling mounting.
Strobe Options:
Single Candela Wall: 1575 cd
Multi Candela Field Selectable Wallall: 15/30/75/110 cd or 135/185 cd
Ceiling
Ceiling: 15/30/75/95 cd or 115/177 cd
Features:
• 3 Selectable dBA settings of 90, 95 and 99 dBA in both tones
• Patented Universal Mounting Plate Series AH
• Wall and ceiling mount Series AS
• Synchronize strobe and audible with Wheelock SM, DSM Sync Modules or PS-12/24-8CP
and PS-12/24-8MP Power Supplies with built-in sync protocol

Order Strobe 24 12 Wall Ceiling
C ode Candela VD C VD C Mount Mount UL MEA CSFM FM B FP
R ed White
AS-24MCW-FR 9024 15/30/75/110 X - X - X - B,D,E,F,G,H,J,N,O,R,X X X X X X
AS-24MCW-FW 9025 15/30/75/110 X - X - - X B,D,E,F,G,H,J,N,O,R,X X X X X X
AS-24MCWH-FR 3468 135/185 X - X - X - B,D,E,F,G,H,J,N,O,R,X X * X * *

AS-24MCWH-FW 3469 135/185 X - X - - X B,D,E,F,G,H,J,N,O,R,X X * X * *
AS-241575W-FR 7405 15 (75 on Axis) X - X - X - B,D,E,F,G,H,J,N,O,R,X X X X X
AS-121575W-FR 7410 15 (75 on Axis) - X X - X - B,D,E,F,G,H,J,N,O,R,X X X X X
AS-24MCC-FR 3161 15/30/75/95 X - - X X - B,D,E,F,G,H,J,N,O,R,X X X X * *

AS-24MCC-FW 3162 15/30/75/95 X - - X - X B,D,E,F,G,H,J,N,O,R,X X X X * *
AS-24MCCH-FW 3467 115/177 X - - X - X B,D,E,F,G,H,J,N,O,R,X X * X * *
180 @ 77°F
ASWP-2475W-FR 9012 75 @ -31°F
X - X - X - I (Outdoor) X X X X X
AH-24-R 7892 - X - X X X - B,D,E,F,G,H,J,N,O,R,X X X X X X

AH-24-W 7893 - X - X X - X B,D,E,F,G,H,J,N,O,R,X X X X X X
AH-12-R 7891 - - X X X X - B,D,E,F,G,H,J,N,O,R,X X X X X X
AH-12-W 7894 - - X X X - X B,D,E,F,G,H,J,N,O,R,X X X X X X
AH-24WP-R 7416 - X - X X X - K (Outdoor) X X X * X
AH-12WP-R 7415 - - X X X X - K (Outdoor) X X X * X
#See mounting options pull out guide in the last section of this binder.
X = Approved * = Pending
Average RMS Current
Audible Wall Mount Audible Strobe Models Ceiling Mount Strobe Models
24 VDC Models AH-24 AS-241575W AS-24MCW AS-24MCWH ASWP-2475W** AS-24MCC AS-24MCCH
1 5 7 5 cd 1 5 cd 3 0 cd 7 5 cd 110cd 135cd 1 8 5 cd 1 5 cd 3 0 cd 7 5 cd 9 5 cd 115cd 177cd
24 vd c 0.062 0.100 0.080 0.102 0.150 0.194 0.250 0.320 0.128 0.088 0.114 0.165 0.205 0.250 0.320
High (99) dBA
UL max* 0.080 0.121 0.088 0.125 0.200 0.267 0.355 0.480 0.168 0.095 0.138 0.221 0.285 0.355 0.480
24 vd c 0.033 0.080 0.060 0.084 0.132 0.173 0.230 0.305 0.105 0.066 0.092 0.145 0.186 0.230 0.305
Med (95) dBA
UL max* 0.043 0.107 0.074 0.110 0.190 0.253 0.340 0.465 0.155 0.080 0.122 0.201 0.269 0.340 0.465
24 vd c 0.017 0.072 0.052 0.076 0.121 0.158 0.220 0.295 0.098 0.056 0.082 0.132 0.173 0.220 0.295
Low (90) dBA
UL max* 0.021 0.100 0.068 0.105 0.182 0.245 0.335 0.460 0.150 0.074 0.113 0.198 0.263 0.335 0.460
Audible Wall Mount Audible * RMS current ratings are per UL average RMS method. UL max current
AH-12 Strobe AS-121575W
rating is the maximum RMS current within the listed voltage range (16-
12 VDC Models Low Med Low
High (99) High (99) 33v for 24v units). For strobes the UL max current is usually at the
Med (95) dBA (90) (95) (90) minimum listed voltage (16v for 24v units). For audibles the max current
dB A dB A
D BA dB A D BA
is usually at the maximum listed voltage (33v for 24v units). For unfiltered
12 vdc 0.163 0.076 0.039 0.260 0.195 0.175 FWR ratings, see installation instructions.
UL max* 0.192 0.108 0.058 0.320 0.275 0.265 **Audible and Visual Combined.
10/04
Series HS4 Horn Strobe
Helping People Take ActionSM & Series HS Horn
Appliance
Description:
Series HS4 Horn Strobe and the Series HS Horn appliances are
the choice for 4 wire horn strobe applications with 3 selectable
dBA settings (90, 95, 99). They satisfy virtually all requirements
for indoor, wall mount applications.
Strobe Options:
Single Candela Wallall: 1575 cd
Multi Candela Field Selectable Wall all: 15/30/75/110 cd
135/185 cd
Features:
• 3 Selectable dBA settings of 90, 95 and 99 dBA in both tones
• 4-Wire Horn Strobe Appliance allows for separate operation Series HS4
of the horn and strobe circuits
• Wall mount Series HS
• Synchronize strobe and audible with Wheelock SM, DSM
Sync Modules or PS-12/24-8CP and PS-12/24-8MP Power
Supplies with built-in sync protocol

Order Strobe 24 2 4 Mounting
Model Number Color Color
C ode Candela VD C WIRE WIRE Options# UL MEA CSFM FM B FP
Red White
HS4-24MCW-FR 3150 15/30/75/110 X X X X - D,E,F,L,M,O,P,R X X X X *
HS4-24MCW-FW 3151 15/30/75/110 X X X - X D,E,F,L,M,O,P,R X X X X *
HS4-241575W-FR 3176 15 (75 on Axis) X X X X - D,E,F,L,M,O,P,R X X X X *
HS4-241575W-FW 3177 15 (75 on Axis) X X X X - D,E,F,L,M,O,P,R X X X X *
HS4-24MCWH-FR 3132 135/185 X X X X - D,E,F,L,M,O,P,R X X X * *
HS4-24MCWH-FW 3148 135/185 X X X - X D,E,F,L,M,O,P,R X X X * *
HS-24-R 3152 - X X X - D,E,F,L,M,O,P,R X X X X *
HS-24-W 3153 - X X - X D,E,F,L,M,O,P,R X X X X *
X = Approved
* = Pending
Average RMS Current
Audible Current Strobe Current
HS/HS4
H S an d H S 4 HS4-241575W HS4-24MCW HS4-24MCWH
Series
High (99) dBA Med (95) dBA Low (90) dBA 1 5 7 5 cd 1 5 cd 3 0 cd 7 5 cd 110cd 1 3 5 cd 1 8 5 cd
24 vd c 0.098 0.052 0.024 0.060 0.041 0.063 0.109 0.140 0.195 0.270
UL max* 0.110 0.068 0.027 0.090 0.060 0.092 0.165 0.220 0.300 0.420
* RMS current ratings are per UL average RMS method. UL max current rating is the maximum RMS current
within the listed voltage range (16-33v for 24v units). For strobes the UL max current is usually at the
minimum listed voltage (16v for 24v units). For audibles the max current is usually at the maximum listed
voltage (33v for 24v units). For unfiltered FWR ratings, see installation instructions.
08/04
Series MT & MT Strobe
Helping People Take ActionSM Multitone Electronic
Appliances
Description:
Series MT & MT Strobe Multitone Electronic Appliances are ideal
for designs that require a choice of 8 selectable alerting sounds
for various ambient and wall conditions and 2 selectable sound
output levels.
Strobe Options:
Single Candela: 1575 cd (MT)
Outdoor (UL 1638): 180 cd (MTWP)
115 VAC (UL 1638): 15 cd (MT4)
Features: Series MT
• Choice of eight (8) alerting sounds: Horn, Bell, March Time Horn, Code-3 Tone, Series MT
Code-3 Horn, Slow Whoop, Siren, or Hi/Lo without strobe
• Audible and strobe can operate from a single NAC circuit with any of the eight
audible sounds
• MT and MTWP Strobes can be Synchronized with Wheelock SM, DSM Sync Modules
or PS-12/24-8CP and PS-12/24-8MP Power Supplies with built-in sync protocol
Model Order Input Rated Mounting Agency Approvals
Number C ode Voltage Candela Options# UL MEA CSFM FM BFP
MT-12/24-R 5023 12/24 - D,E,F,L,M,O,P,R X X X X X
MT-12/24-W 5024 12/24 - D,E,F,L,M,O,P,R X X X X X

#See mounting options pull out
MT-241575W-FR 8422 24 15 (75 on AXIS) D,E,F,L,M,O,P,R X X X X * guide in the last section of this
MT-241575W-FW 9460 24 15 (75 on AXIS) D,E,F,L,M,O,P,R X X X X * binder.
X = Approved
MT-24MCW-FR 3301 24 15/30/75/110 D,E,F,L,M,O,P,R X * X * * * = Pending
MT-24MCW-FW 3303 24 15/30/75/110 D,E,F,L,M,O,P,R X * X * *
MT-121575W-FR 8421 12 15 (75 on AXIS) D,E,F,L,M,O,P,R X X X X *
180 @ 77°F
MTWP-2475W-FR 8420 24
75 @ -31°F
M (Outdoor) X X X X *
MT4-115-R 6223 115VAC - D, E, J, K, N, O, R X X X X X
MT4-115-WH-VFR 6224 115 VAC 15 D, E, J, K, N, O, R X X X X X
dBA and Current Ratings for Multitone Audible Portion

RMS Current (amps) dBA @ 10ft (UL Reverberant) dBA @ 10ft (anechoic)
24 V D C 12 V D C 24 V D C 12 V D C 12 and 24 VDC
HI Output STD Output HI Output STD Output
HI STD HI STD
@ 24 UL @ 24 UL @ 24 UL @ 24 UL HI Output STD Output
Output Output Output Output
VD C max* VD C max* VD C max* VD C max*
Horn 0.074 0.108 0.033 0.044 0.145 0.176 0.023 0.034 92 87 90 77 99 93
Bell 0.040 0.053 0.018 0.024 0.077 0.095 0.014 0.020 86 80 85 69 92 87
March Time Horn 0.067 0.104 0.033 0.038 0.109 0.142 0.023 0.034 89 84 89 74 99 93
Code-3 Horn 0.069 0.091 0.026 0.035 0.100 0.142 0.023 0.034 88 83 88 73 99 93
Code-3 Tone 0.061 0.075 0.026 0.035 0.088 0.105 0.015 0.021 85 80 84 70 95 90
Slow Whoop 0.069 0.098 0.028 0.037 0.100 0.142 0.025 0.035 90 89 89 75 99 94
Siren 0.080 0.104 0.027 0.036 0.122 0.152 0.021 0.030 89 84 89 75 98 93
HI/LO 0.044 0.057 0.020 0.026 0.089 0.114 0.018 0.026 86 81 86 71 93 88
* RMS current ratings are per UL average RMS method. UL

Strobe Current Ratings (AMPS) max current rating is the maximum RMS current within the
Model MT-121575 MT-241575 MTWP-2475 MT-24MCW listed voltage range (16-33v for 24v units). For strobes the UL
max current is usually at the minimum listed voltage (16v for
Candela 1 5 7 5 cd 1 5 7 5 cd 1 8 0 cd 1 5 cd 3 0 cd 7 5 cd 110cd
24v units). For audibles the max current is usually at the
@24VDC 0.152 0.060 0.094 0.041 0.063 0.109 0.140 maximum listed voltage (33v for 24v units). For unfiltered
FWR ratings, see installation instructions.
UL max* 0.255 0.090 0.138 0.060 0.092 0.165 0.220
10/04
Series AMT & AMT
Strobe Multitone Input
Electronic Appliances
Description:
Series AMT & AMT Strobe Multitone Input Electronic Appliances
are designed for applications that require up to three distinct
prioritized audible signals from 3 isolated inputs. They are ideal
for combination fire and burglary systems and suppression
systems.
Strobe Options:
Single Candela Wall
all: 1575 cd
75 cd
Features:
Series AMT
• Choice of eight (8) self-prioritized sound combinations
• Three electrically isolated audible signal inputs Series AMT
• Each AMT Audible and AMT Strobe appliance has two selectable sound without strobe
output levels: Up to 98 dBA at 10 feet on the high setting and up to 93 dBA on the
standard setting
• AMT with strobe can flash independently or in unison with all audible signals
• AMT Strobes can be Synchronized with Wheelock SM, DSM Sync Modules or
PS-12/24-8CP and PS-12/24-8MP Power Supplies with built-in sync protocol

Order Input Rated Mounting Agency Approvals
Model Number
C ode Voltage Candela Options#
UL MEA CSFM FM B FP
AMT-12/24-R 5887 12/24 - D,E,F,L,M,N,O,P,R X X X X X
AMT-241575W-FR 9463 24 15 (75 on axis) D,E,F,L,M,N,O,P,R X X X X *
#See mounting options
AMT-241575W-FW 9466 24 15 (75 on axis) D,E,F,L,M,N,O,P,R X X X X * pull out guide in the last
section of this binder.
AMT-24MCW-FR 3300 24 15/30/75/110 D,E,F,L,M,N,O,P,R X * X * *
X = Approved
AMT-24MCW-FW 3302 24 15/30/75/110 D,E,F,L,M,N,O,P,R X * X * * * = Pending
NYC indicates
AMT-12/24-R-NYC 7920 12/24 - D,E,F,L,M,N,O,P,R X X
tones for New
AMT-241575W-FR-NYC 9465 24 15 (75 on axis) D,E,F,L,M,N,O,P,R X X York City.
Current Ratings for AMT Multitone Audible Signals

RMS Current (amps) Average RMS Current
24 vd c 12 vd c RMS Current (amps)
HI Output STD Output HI Output STD Output AMT-121575 AMT-24MCW
Model
Tone @ 24 UL @ 24 UL @ 12 UL @ 12 UL
Candela 1 5 7 5 cd 1 5 cd 3 0 cd 7 5 cd 110cd
VD C max* VD C max* VD C max* VD C max*
Horn 0.085 0.108 0.034 0.043 0.100 0.210 0.020 0.058 @24VDC 0.064 0.041 0.063 0.109 0.140
Bell 0.042 0.057 0.020 0.026 0.031 0.117 0.010 0.031 UL max* 0.101 0.060 0.092 0.165 0.220
March Time Horn 0.085 0.108 0.026 0.035 0.100 0.210 0.020 0.059 * RMS current ratings are per UL average RMS
Code-3 Horn 0.085 0.108 0.034 0.043 0.100 0.210 0.020 0.057 method. UL max current rating is the maximum
RMS current within the listed voltage range (16-
Code-3 Tone 0.048 0.060 0.022 0.030 0.060 0.168 0.015 0.052 33v for 24v units). For strobes the UL max current
Slow Whoop 0.087 0.112 0.034 0.044 0.100 0.182 0.025 0.056 is usually at the minimum listed voltage (16v for
24v units). For audibles the max current is usually
Siren 0.081 0.102 0.028 0.038 0.082 0.177 0.020 0.055 at the maximum listed voltage (33v for 24v units).
HI/LO 0.047 0.064 0.023 0.030 0.044 0.131 0.013 0.028 For unfiltered FWR ratings, see installation
instructions.
Vibrating Chime 0.032 0.041 0.015 0.020 0.027 0.090 0.010 0.028
10/04
Series MIZ Piezoelectric
Mini Horns
Description:
Wheelock Series MIZ Piezoelectric Mini Horns offer high sound
output along with low current draw and are ideal for alarm
signaling in individual rooms, apartments, hotels, motels, and
offices. Field selectable continuous or code 3 output with sync
capability.
Features:
• Continuous or Code 3 output
• Synchronize with Wheelock’s SM, DSM Sync Modules or
PS-12/24-8CP and PS-12/24-8MP Power Supplies with built-in
sync protocol
• Mount to single-gang boxes
Series MIZ
Model Order Mounting Agency Approvals
Description
Number C ode Options# UL MEA C S FM FM B FP
MIZ-24S-R 8485 24 Volt, Red B X X X X *
MIZ-24S-W 8484 24 Volt, White B X X X X *
X = Approved
* = Pending
UL Listed Models and Ratings

Reverberant dBA Anechoic dBA
Average
Regulated Per UL 464 @ 10 ft @ 10 ft
RMS Mounting
Model UL
Current* Continuous C ode 3 Continuous C ode 3 Options
Voltage
(AMPS)
dB A dB A dB A dB A
24 V D C 0.025 83.2 78.8 87.9 87.9 B
MIZ-24S
UL max* 0.026 85.8 81.3 90.6 89.7 B
* RMS current ratings are per UL average RMS method. UL max current
rating is the maximum RMS current within the listed voltage range (16-33v
for 24v units). For strobes the UL max current is usually at the minimum
listed voltage (16v for 24v units). For audibles the max current is usually
at the maximum listed voltage (33v for 24v units). For unfiltered FWR
ratings, see installation instructions.
08/04
Series RSS Strobes &
Series RSSP Strobe
Description: Plate Appliances
Wheelock Series RSS Strobes provide a wide range of intensities
and mounting options for wall or ceiling applications.
Series RSSP Single & Multi-Candela Strobe Plates are designed
for retrofitting existing audible notification appliances to strobe
applications.
Strobe Options:
Single Candela: 1575 cd (wall), 75 cd (weatherproof)
all: 15/30/75/110 cd or 135/185 cd
Ceiling
Ceiling: 15/30/75/95 cd or 115/177 cd
Features:
Series RSS
• Patented Universal Mounting Plate
• Low current draw to reduce power consumption and wiring costs
• Strobes produce 1 flash per second over the regulated voltage range Series RSSP
• Synchronize with Wheelock’s SM, DSM Sync Modules or PS-12/24-8CP
and PS-12/24-8MP Power Supplies with built-in sync protocol
Order Wall Ceiling Strobe 24 12 Square or
C ode Mount Mount Candela VD C VD C R ound UL MEA CSFM FM BFP
R ed White
RSS-24MCW-FR 9400 X - 15/30/75/110 X - X - B,D,E,F,G,H,J,N,O,P,R,X Square X X X X X
RSS-24MCW-FW 9401 X - 15/30/75/110 X - - X B,D,E,F,G,H,J,N,O,P,R,X Square X X X X X
RSS-241575W-FR 7471 X - 15 (75 on Axis) X - X - B,D,E,F,G,H,J,N,O,P,R,X Square X X X X X
RSS-241575W-FW 7788 X - 15 (75 on Axis) X - - X B,D,E,F,G,H,J,N,O,P,R,X Square X X X X X
RSS-121575W-FR 7476 X - 15 (75 on Axis) - X X - B,D,E,F,G,H,J,N,O,P,R,X Square X X X X X
RSS-121575W-FW 7468 X - 15 (75 on Axis) - X - X B,D,E,F,G,H,J,N,O,P,R,X Square X X X X X
RSS-24MCC-FW 3158 - X 15/30/75/95 X - - X B,D,E,F,G,H,J,N,O,P,R,X Square X X X X *

RSS-24MCCR-FW 3159 - X 15/30/75/95 X - - X B,D,E,F,G,H,J,N,O,P,R,X Round X X X X *
RSS-24MCCH-FW 3461 - X 115/177 X - - X B,D,E,F,G,H,J,N,O,P,R,X Square X X X * *
RSS-24MCCHR-FW 3463 - X 115/177 X - - X B,D,E,F,G,H,J,N,O,P,R,X Round X X X * *
RSS-24MCWH-FR 3465 X 135/185 X X B,D,E,F,G,H,J,N,O,P,R,X Square X X X * *
180 @ 77°F
RSSWP-2475W-FR 9013 X -
75 @ -31°F
X - X - B,D,E,F,G,H,J,N,O,P,R,X Square X X X X *
180 @ 77°F
RSSWP-2475W-FW 3034 X -
75 @ -31°F
X - - X T (Outdoor) Square X X X X *
RSSP-121575W-FR 7798 X - 15 (75 on Axis) - X X - E,Z Square X X X X X
RSSP-24MCW-FR 9402 X - 15/30/75/110 X - X - E,Z Square X X X X X
RSSP-241575W-FR 7793 X - 15 (75 on Axis) - - X - E,Z Square X X X X X
RSSP-24MCWH-FR 9482 X 135/185 X X B,D,E,F,G,H,J,N,O,P,R,X Square X X X * *
Average RMS Current
RSS/RSSP - Wall Mount RSS - Ceiling Mount
RSS/RSSP
24V D C 241575W 24MCW 24MCWH 24MCC 24MCCH
Models
1 5 7 5 cd 1 5 cd 3 0 cd 7 5 cd 110cd 135cd 185cd 1 5 cd 3 0 cd 7 5 cd 9 5 cd 115cd 1 7 7 cd
24 vd c 0.060 0.041 0.063 0.109 0.140 0.195 0.270 0.045 0.070 0.119 0.159 0.195 0.270
UL max* 0.090 0.060 0.092 0.165 0.220 0.300 0.420 0.065 0.105 0.189 0.249 0.300 0.420
RSS/RSSP RSS/RSSP
* RMS current ratings are per UL average RMS method. UL max current rating is the maximum
24V D C Wall Mount
RMS current within the listed voltage range (16-33v for 24v units). For strobes the UL max
Models 121575W current is usually at the minimum listed voltage (16v for 24v units). For audibles the max
current is usually at the maximum listed voltage (33v for 24v units). For unfiltered FWR
12 vd c 0.152 ratings, see installation instructions.
UL max* 0.255
08/04
Helping People Take ActionSM Series CH Chimes &
Chime Strobes
Description:
Wheelock Series CH Chimes & Chime Strobes are ideal for
hospital and institutional applications. The appliances feature
single stroke or vibrating operation.
Strobe Options:
Single Candela Wall
all: 1575 cd
all: 15/30/75/110 cd
135/185 cd
Ceiling
Ceiling: 15/30/75/95 cd
115/177 cd
Features:
• Anechoic sound level adjustable up to 83dB
• Tone adjustable from 800 to 1200 Hz Series CH70
• Adjustable volume and tone control Series CH90
Chime Strobe
• CH Strobes may be Synchronized with Wheelock’s SM, DSM Chime

Model Wall Ceiling Strobe 24 Model Model Color Mounting Agency Approvals
Model Number
C ode Mount Mount Candela VD C Color Red White Options# UL MEA CSFM BFP
CH70-24MCW-FR 9018 X 15/30/75/110 X X - L,O,P,Q,R,U,Y X X X X
CH70-24MCW-FW 9019 X - 15/30/75/110 X - X L,O,P,Q,R,U,Y X X X X
CH70-24MCWH-FR 9083 X - 135/185 X X - L,O,P,Q,R,U,Y X X X *

CH70-24MCWH-FW 9084 X - 135/185 X - X L,O,P,Q,R,U,Y X X X *
CH70-241575W-FR 7830 X - 15 (75 on Axis) X X - L,O,P,Q,R,U,Y X X X X
CH90-24MCC-FW 3168 - X 15/30/75/95 X - X Q,U,V X X X *

CH90-24MCCH-FW 3110 - X 115/177 X - X Q,U,V X X X *
CH70-24-R 7825 X X - X X - L,O,P,Q,R,U,Y X X X X
CH70-24-W 7827 X X - X - X L,O,P,Q,R,U,Y X X X X
CH90-24-W 7826 X X - X - X Q,U,V X X X X
Average RMS Current

CH70 Strobe current - Wall Mount CH90 Strobe current - Ceiling Mount
CH70/CH90 Chime
241575W 24MCW 24MCWH 24MCC 24MCCH
Chimes current
1 5 7 5 cd 1 5 cd 3 0 cd 7 5 cd 110cd 1 3 5 cd 1 8 5 cd 1 5 cd 3 0 cd 7 5 cd 9 5 cd 115cd 1 7 7 cd
24 vd c 0.022 0.060 0.041 0.063 0.109 0.140 0.195 0.270 0.045 0.070 0.119 0.159 0.195 0.270
UL max* 0.022 0.090 0.060 0.092 0.165 0.220 0.300 0.420 0.065 0.105 0.189 0.249 0.300 0.420
* RMS current ratings are per UL average RMS method. UL max current rating is the maximum RMS current within the
listed voltage range (16-33v for 24v units). For strobes the UL max current is usually at the minimum listed voltage
(16v for 24v units). For audibles the max current is usually at the maximum listed voltage (33v for 24v units). For
unfiltered FWR ratings, see installation instructions.
08/04
Helping People Take ActionSM Series MB
Motor Bells
Description:
Wheelock Series MB Motor Bells provide a better engineering
motor bell for fire and life safety alarm systems.
Features:
• Available in 6” and 10” sizes in 12 or 24 VDC models.
• For combined audible (bell) and visual signaling,
convenient retrofit assemblies (Series RSSP) are available
with multi-candela or 1575 cd strobes
• Built-in trimplate make semi-flush mounting simpler and
less expensive
Series MB
Average Agency Approvals
Model Order Shell Input Voltage UL dB A @ Mounting
RMS
Number C ode Siz e (VDC) Max* 10ft. Options# UL MEA CSFM FM BFP
Current
MB-G6-12-R 3942 6” 12 0.060 0.090 92 D,E,J,K,N,O,P,R,S X X X X X
X = Approved
* RMS current ratings are per UL average RMS method. UL max current rating is the maximum RMS current within the listed voltage range (16-33v for
24v units). For strobes the UL max current is usually at the minimum listed voltage (16v for 24v units). For audibles the max current is usually at the
maximum listed voltage (33v for 24v units). For unfiltered FWR ratings, see installation instructions.
Series 43T AC
Vibrating Bells
Description:
Wheelock Series 43T AC Vibrating Bells provide durable
operation and dependable performance for indoor and
outdoor installations.
Features:
• Available in 6” and 10” sizes
• 115 or 24 VAC operation
Series 43T
Order Shell Input Input dB A @ Mounting Agency Approvals

Model Number
C ode Siz e Voltage Current 10 Ft. Options#
UL MEA C S FM FM B FP
43T-G6-24-R 1627 6” 24 VAC 0.410 86 D,E,J,K,N,O,P,R,S X X X X X
X = Approved
08/04
Series 31T 115 VAC
Horn
Description:
Wheelock Series 31T 115 VAC Horn is a high performance
horn ideal for the life safety applications where high sound
output, low current draw, and dependable operation are of
critical concern.
Features:
• Offers rugged, vandal resistant construction with die cast
metal housings for the horn and mechanism
Specification and Ordering Information Series 31T

Model Order Input Rated Rated dBA Mounting Agency Approvals
Number C ode Voltage Current @ 10 F eet Options#
31T-115-R 2805 115 VAC 0.160 95 D,E,J,K,N,O,R X X X X X #See mounting options pull out guide in
X = Approved
* = Pending
Class Group Contents of Haz ardous Atmosphere
I B Hydrogen, or gases and vapors of equibalent hazards suh as manufactured gas
I C Ethyl and ether vapors
I D Gasoline, petroleum, naphtha, alcohol, acetone, benzene, lacquer solvent, vapors, natural gas
II F Carbon black, coal, coke dust
II G Flour, starch, grain dusts
Series CVX/CSX
Explosion Proof Bells
Description:
Wheelock Series CVX/CSX Explosion Proof Bells are listed for
service in Division One applications, which means they are
designed to operate safely in atmospheres that actually
contain the explosive elements in free form
Features:
• Available in 24 VDC and 115 VAC models
• Available in single stroke and vibrating models
• High sound output with large 10” bell shell
• Approvals: Underwriter’s Laboratories (UL), New York City Series CVX10, CSX10 Series CVXG10, CSXG10
(MEA), California State Fire Marshal (CSFM) (Indoor Model) (Outdoor Model)
Vibrating
Indoor Model Order Outdoor Model Order Shell Input Input dB A @
Mounting
Number C ode Number C ode Siz e Volt. Current 10 Ft.
CVX10-115-R 3742 CVXG10-115-R 4930 10” 115VAC .220 90 Note 1
Single Stroke
NOTE:
Indoor Model Order Outdoor Model Order Shell Input Input dB A @ 1. All models Include integral
Mounting
Number C ode Number C ode Siz e Volt. Current 10 Ft. cast backbox for surface
mounting with 1/2” threaded
CSX10-115-R 4715 CSXG10-115-R 4929 10” 115VAC 0.125 87 Note 1 conduit entrances on top
CSX10-24-R 3582 CSXG10-24-R 3402 10" 24V D C 0.500 87 Note 1 and bottom of housing.
02/04
Weatherproof Series AHWP Audibles,
SM
Helping People Take Action ASWP Audible Strobes, MTWP
Multitone Strobes, RSSWP Strobes &
Description: ET70WP Speaker Strobes Appliances
Wheelock has the broadest UL Listed weatherproof product line
in the industry with an extended temperature range of -31°F to
150°F (-35°C to 66°C) per UL 1638.
Features: Series
• Synchronize with Wheelock’s SM, DSM sync modules or MTWP
PS-12/24-8CP and PS-12/24-8MP Power Supplies with built-in
sync protocol (NotMT-12/24 or audible portion of MTWP) Series ET70WP
• Strobe models are rated 180 cd @ 77°F Series
RSSWP
Series ASWP Series AHWP

Strobe cd Strobe cd Outdoor
Order Input B ack B o x &
Model Number @ 77°F @ -31°F dB A Mounting Agency Approvals
C ode Voltage Order Code
(25°C) (-35°C) Options#
Strobe UL MEA CSFM FM B FP
RSSWP-2475W-FR 9013 1 8 0 cd 7 5 cd - 24 V D C T WPSBB-R (9751) X X X X *
RSSWP-2475W-FW 3034 1 8 0 cd 7 5 cd - 24 V D C T WPSBB-W (3033) X X X X *
Audible Strobe
ASWP-2475W-FR 9012 1 8 0 cd 7 5 cd 90/95/99 24 V D C I WPBB-R (9014) X X X X X
Multitone Strobe
MTWP-2475W-FR 8420 1 8 0 cd 7 5 cd 76-94 24 V D C M IOB-R (5046) X X X X *
Horns/Audibles
AH-24WP-R 7416 N/A N/A 90/95/99 24 VDC K WBB-R (2959) X X X - X
AH-12WP-R 7415 N/A N/A 90/95/99 12 VDC K WBB-R (2959) X X X - X
MT-12/24-R 5023 N/A N/A 76-94 12/24 VDC M IOB-R (5046) X X X X X
Speaker Strobe
ET70WP-2475W-FR 9077 1 8 0 cd 7 5 cd 77-93 24 V D C M IOB-R (5046) X X X * *
Average RMS Current
Series RSSWP and Strobe in MTWP Series ASWP**
Avg. Current * High dBA Medium dBA Low dB A
Strobe 75 cd @ Regulated
Voltage Setting Setting Setting
-31°F (-35°C) Voltage Range
24.0 VDC UL Max* (99) dBA (95) dBA (90) dBA
RSSWP-2475W-FR 16.0 - 33.0 VDC 0.094 0.138 24.0 VDC 0.128 0.105 0.098
UL Max* 0.168 0.155 0.150
24 V Series MTWP
Series AHWP
Audible Strobe
Voltage AH-24WP Voltage AH-12WP
24.0 VDC UL Max* 24.0 VDC UL Max*
Tone AH-24WP Hi/Med/Low AH-12WP Hi/Med/Low
Standard High Standard High
24.0 VDC 0.062/0.033/0.017 12.0 VDC 0.163/0.076/0.039
Horn 0.033 0.074 0.044 0.108
UL Max* 0.080/0.043/0.021 UL Max* 0.192/0.108/0.058
Bell 0.018 0.040 0.024 0.053
* RMS current ratings are per UL average RMS method. UL max
March Time 0.033 0.067 0.038 0.104 current rating is the maximum RMS current within the listed voltage
Code 3 Horn 0.026 0.069 0.035 0.091 0.094 0.138 range (16-33v for 24v units). For strobes the UL max current is
usually at the minimum listed voltage (16v for 24v units). For
Code 3 Tone 0.026 0.061 0.035 0.075 audibles the max current is usually at the maximum listed voltage
(33v for 24v units). For unfiltered FWR ratings, see installation
Slow Whoop 0.028 0.069 0.037 0.098
instructions.
Siren 0.027 0.080 0.036 0.104 **Audible and Visual Combined.
Hi/Lo 0.020 0.044 0.026 0.057

10/04
Series E50 Speakers &
Speaker Strobes
Description:
Series E50 Speakers & Speaker Strobes are designed for high
efficiency sound output with field selectable input voltage
(25/70 VRMS) and field selectable taps from 1/8 to 2 watts.
They are also designed to provide a sleek, aesthetic
appearance for emergency voice/alarm communication
systems.
Strobe Options:
Single Candela Wall
all: 1575 cd
all: 15/30/75/110 cd
or 135/185 cd
Features: Series E50 Series E50

• Mount to 4” square x 2-1/8” deep backbox with no extension Speaker Strobe Speaker
ring required
• High efficiency design for maximum output at minimum
wattage across a listed frequency range of 400 to 4000 Hz
• Strobes may be synchronized with Wheelock’s SM, DSM
Specification and Ordering Information Note: Available October 2004
Surface Agency Approvals

Order Wall Ceiling Strobe Grill Flush Mount
Model Mount Mounting Options
C ode Mount Mount Candela Color B ackb o x UL MEA CSFM FM BFP
B ackb o x
E50-R 0222 X X - Red 4' x 4" x 2-1/8" E50SB-R E,O,P,Q,R,U,Y,AA X * * * *

E50-W 0223 X X - White 4' x 4" x 2-1/8" E50SB-W E,O,P,Q,R,U,Y,AA X * * * *
E50-241575W-FR 0224 X - 15 (75 on Axis) Red 4' x 4" x 2-1/8" E50SSB-R E,Q,U,BB X * * * *
E50-241575W-FW 0225 X - 15 (75 on Axis) White 4' x 4" x 2-1/8" E50-SSB-W E,Q,U,BB X * * * *
E50-24MCW-FR 0226 X - 15/30/75/110 Red 4' x 4" x 2-1/8" E50SSB-R E,Q,U,BB X * * * *
E50-24MCW-FW 0227 X - 15/30/75/110 White 4' x 4" x 2-1/8" E50-SSB-W E,Q,U,BB X * * * *
E50-24MCWH-FR 0228 X - 135/185 Red 4' x 4" x 2-1/8" E50SSB-R E,Q,U,BB X * * * *
E50-24MCWH-FW 0229 X - 135/185 White 4' x 4" x 2-1/8" E50-SSB-W E,Q,U,BB X * * * *

pull out guide in the last
section of this binder.
Average RMS Current X = Approved
* = Pending
E50 Strobe Current - Wall Mount
E 50
S p eaker 241575W 24MCW 24MCWH * RMS current ratings are per UL average RMS method. UL max
Strobes current rating is the maximum RMS current within the listed
1 5 7 5 cd 1 5 cd 3 0 cd 7 5 cd 110cd 1 3 5 cd 1 8 5 cd voltage range (16-33v for 24v units). For strobes the UL max
current is usually at the minimum listed voltage (16v for 24v
24 vd c 0.060 0.041 0.063 0.109 0.140 0.195 0.270 units). For audibles the max current is usually at the maximum
listed voltage (33v for 24v units). For unfiltered FWR ratings,
UL max* 0.090 0.060 0.092 0.165 0.220 0.300 .0420 see installation instructions.
E50 UL Reverberant dBA @ 10 Feet**
w atts 1/8 1/4 1/2 1 2

E 50 S p eaker 77 79.5 82.5 85 88
E50 Speaker Strobe 77 79.5 82.5 85 88
**dBA ratings are based on UL testing under UL Standard 1480
10/04
Series E Low Profile
Speakers & Speaker
Strobes
Description:
Series E Speakers & Speaker Strobes are designed for high
efficiency sound output with field selectable input voltage
(25/70 VRMS) and field selectable taps from 1/8 to 2 watts.
Strobe Options:
Single Candela Wall
all: 1575 cd
all: 15/30/75/110 cd
or 135/185 cd
Ceiling
Ceiling: 15/30/75/95 cd Series E70
or 115/177 cd Speaker
Features:
• Strobes may be synchronized with Wheelock’s SM, DSM
Sync Modules or PS-12/24-8CP and PS-12/24-8MP Power Series E70 Series E90
Supplies with built-in sync protocol Speaker Strobe Speaker

Order Wall Ceiling Strobe Model Model Model Mounting Agency Approvals
Model Number
Code Mount Mount Candela Color Red Color White Color Nickel Options# UL MEA CSFM FM B FP
E70-24MCW-FR 9022 X - 15/30/75/110 X - - L,O,P,Q,R,U,Y X X X * X
E70-24MCW-FW 9023 X - 15/30/75/110 - X - L,O,P,Q,R,U,Y X X X * X
E70-24MCW-FN 3099 X - 15/30/75/110 - - X Q,U X X X * X
E70-241575W-FR 7871 X - 15 (75 on Axis) X - - L,O,P,Q,R,U,Y X X X * X
E70-241575W-FW 7868 X - 15 (75 on Axis) - X - L,O,P,Q,R,U,Y X X X * X
E70-241575W-FN 3100 X - 15 (75 on Axis) - - X L,O,P,Q,R,U,Y X X X * X
E70-R 7866 X X - X - - P,Q,U X X X X X

E70-N 3108 X X - - - X P,Q,U X X X X X
E70-24MCWH-FR 3470 X - 135/185 X - - L,O,P,Q,R,U,Y X X X * *

E70-24MCWH-FW 3474 X - 135/185 - X - L,O,P,Q,R,U,Y X X X * *
E70-24MCWH-FN 0059 X - 135/185 - - X Q,U X X X * *
E90-24MCC-FW 3166 - X 15/30/75/95 - X - Q,U,V X X X * *
E90-24MCC-FN 3185 - X 15/30/75/95 - - X Q,U,V X X X * *
pull out guide in the last
E90-W 7869 X X - - X - Q,U,V X X X X X section of this binder.
E90-N 3109 X X - - - X Q,U,V X X X X X X = Approved
* = Pending
E90-24MCCH-FW 3471 - X 115/177 - X - Q,U,V X X X * *
E90-24MCCH-FN 0062 - X 115/177 - - X Q,U,V X X X * *
Average RMS Current

E70 Strobe C urrent - Wall Mount E90 Strobe C urrent - C eiling Mount
E70/E90
S p eaker 241575W 24MC W 24MC WH 24MC C 24MC C H
Strobes
24 vd c 0.060 0.041 0.063 0.109 0.140 0.195 0.270 0.045 0.070 0.119 0.159 0.195 0.270
UL max* 0.090 0.060 0.092 0.165 0.220 0.300 .0420 0.065 0.105 0.189 0.249 0.300 0.420
E70/E90 U L R everbant dB A @ 10 Feet** rating is the maximum RMS current within the listed voltage range (16-
33v for 24v units). For strobes the UL max current is usually at the
w atts 1/8 1/4 1/2 1 2 minimum listed voltage (16v for 24v units). For audibles the max current
is usually at the maximum listed voltage (33v for 24v units). For
E S p eaker 78.1 80.8 83.8 86.0 88.8 unfiltered FWR ratings, see installation instructions.
**dBA ratings are based on testing under UL Standard 1480.
E Speaker Strobe 77.5 80.4 83.2 85.7 87.8
08/04
Helping People Take ActionSM Series ET Speakers &
Speaker Strobes
Description:
Series ET Speakers & Speaker Strobes provide high audio
output, clear audibility, field selectable input voltage (25/70
VRMS) and field selectable taps from 1/8 to 8 watts.
Strobe Options:
Single Candela Wall: 1575 cd
all: 15/30/75/110 cd
or 135/185 cd
Ceiling
Ceiling: 15/30/75/95 cd Series ET70
or 115/177 cd Speaker
Features:
wattage across a frequency range of 400 to 4000 Hz
• Synchronize with Wheelock’s SM, DSM Sync Modules or
PS-12/24-8CP and PS-12/24-8MP Power Supplies with built- Series ET70 Series ET90
in sync protocol Speaker Strobe Speaker
Order Wall Ceiling Strobe Model Model Model Mounting Agency Approvals
Model Number
C ode Mount Mount Candela Color Red Color White Color Nickel Options# UL MEA CSFM FM BFP
ET70-24MCW-FR 9020 X - 15/30/75/110 X - L,O,P,Q,R,U,Y X X X * X
ET70-24MCW-FW 9021 X - 15/30/75/110 - X L,O,P,Q,R,U,Y X X X * X
ET70-24MCW-FN 3091 X - 15/30/75/110 - - X Q,U X X X * X
ET70-241575W-FR 7848 X - 15 (75 on Axis) X - L,O,P,Q,R,U,Y X X X * X
ET70-241575W-FN 3092 X - 15 (75 on Axis) - - X Q,U X X X * X
ET70-24MCWH-FR 3472 X - 135/185 X - - L,O,P,Q,R,U,Y X X X * *

ET70-24MCWH-FW 3475 X - 135/185 - X - L,O,P,Q,R,U,Y X X X * *
ET70-24MCWH-FN 0061 X - 135/185 - - X Q,U X X X * *
ET70WP-2475-FR 9077 X - 180 X - - M (Outdoor) X X X * *
ET90-24MCC-FW 3164 - X 15/30/75/95 - X Q,U,V,Y X X X * *
ET90-24MCC-FN 3186 - X 15/30/75/95 - - X Q,U,V,Y X X X * *
ET90-24MCCH-FW 3473 - X 115/177 - X - Q,U,V,Y X X X * *
ET90-24MCCH-FN 0062 - X 115/177 - - X Q,U,V,Y X X X * * #See mounting
options pull out
ET70-R 7840 X X - X - L,O,P,Q,R,U,Y X X X * X guide in the last
section of this
ET70-N 7840 X X - - - X Q,U X X X * X
binder.
ET90-W 7842 X X - - X - Q,U,V X X X * X X = Approved
* = Pending
ET90-N 7842 X X - - - X Q,U,V X X X * X
Average RMS Current

ET70 Strobe current - Wall Mount ET90 Strobe current - Ceiling Mount
ET70/ET90
S p eaker 241575W 24MCW 24MCWH 24MCC 24MCCH
Strobes
24 vd c 0.060 0.041 0.063 0.109 0.140 0.195 0.270 0.045 0.070 0.119 0.159 0.195 0.270
UL max* 0.090 0.060 0.092 0.165 0.220 0.300 0.420 0.065 0.105 0.189 0.249 0.300 0.420
* RMS current ratings are per UL average RMS method. UL max current rating is
ET70/ET90 UL Reverberant dBA @ 10 Feet** the maximum RMS current within the listed voltage range (16-33v for 24v units).
For strobes the UL max current is usually at the minimum listed voltage (16v for
w atts 1/8 1/4 1/2 1 2 4 8 24v units). For audibles the max current is usually at the maximum listed voltage
(33v for 24v units). For unfiltered FWR ratings, see installation instructions.
E T S p eaker 78.3 81.5 84.4 87.2 90.1 92.8 94.9
**dBA ratings are based on UL testing under UL Standard 1480
ET Speaker Strobe 78.3 81.5 84.4 87.2 90.1 92.8 94.9
08/04
Series ET-1010 & ET80
Helping People Take ActionSM Vandal Resistant Speakers
& Speaker Strobes
Description:
Wheelock’s Series ET Vandal Resistant speakers and speaker
strobes provide a full range of rugged, high performance
combinations specifially designed to meet the critical needs
of the life safety industry for voice and tone signaling.
Strobe Options (ET80):

Single Candela Wall
all: 1575 cd
Multi Candela Wall
all: 15/30/75/110cd
or 135/185
Features:
Series ET-1010
Speaker
• SLM Strobes may be synchronize with Wheelock’s SM, DSM Series ET80
Sync Modules or PS-12/24-8MP Power Supply with built-in Speaker Strobe
sync protocol
• Sealed back speaker construction for extra protection and
improved audibility

Order Mounting Mounting Agency Approvals
Model Number Color Candela
C ode Location Options#
ET-1010-R 3135 red wall/ceiling K,N,O,R - X X X X
ET-1010-W 3137 white wall/ceiling K,N,O,R - X X X X
ET-1080-R 3141 red wall/ceiling O,P,Q,Y - X X X X
ET80-241575W-FR 3037 red wall O,P,Q,R,Y 15(75 on axis) X * X * #See mounting

options pull out
ET80-241575W-FW 3038 white wall O,P,Q,R,Y 15(75 on axis) X * X *
guide in the last
15/30/75/110 section of this
ET80-24MCW-FR 3476 red wall O,P,Q,R,Y X * X * binder.
X = Approved
15/30/75/110 X
ET80-24MCW-FW 3477 white wall O,P,Q,R,Y * X * * = Pending
ET80-24MCWH-FR 3478 red wall O,P,Q,R,Y 135/185 X * X *
ET80-24MCWH-FW 3479 white wall O,P,Q,R,Y 135/185 X * X *
Average RMS Current

Model
ET80-241575 ET80-24MCW ET80-24MCWH
Number
candela 1 5 7 5 cd 1 5 cd 3 0 cd 7 5 cd 110cd 1 3 5 cd 1 8 5 cd
@ 24 V D C 0.060 0.041 0.063 0.109 0.140 0.195 0.270
UL max* 0.090 0.060 0.092 0.165 0.220 0.300 0.420
Speaker dBA at 10 Feet (All models)
rating is the maximum RMS current within the listed voltage range (16-
Watts 1/8 1/4 1/2 1 2 4 8 minimum listed voltage (16v for 24v units). For audibles the max current
dB A 78 81 84 87 89 93 96 unfiltered FWR ratings, see installation instructions.
10/04
Helping People Take ActionSM Series S UL Listed 8”
Speaker & Speaker Strobe
Description:
The Series S, 8” Ceiling Speakers and Speaker Strobes are
available in three configurations:
S8-70/25
Dual voltage, multi-tap speaker
S8-24MCC
Speaker with field selectable candela settings of 15/30/75/95cd
S8-24MCCH
Speaker with field selectable candela settings of 115/177cd
Features:
Speaker and Speaker Strobes
• Dual voltage transformer (25/70V) Series S8-24MCC
• Jumper selectable multiple wattage taps: 1/8, ¼, ½, 1, 2, 4, 8 Series S8-24MCCH
• 93 dBA @ 8 watts of source power Series S8-70/25
• Frequency Response: 200Hz – 15kHz
400Hz – 4kHz (UL)
• Magnet weight: 9.5 oz.
• Speaker impedance: 8 ohms
• Round metal 12" grille, with white powder coated finish
• Compatible with DC circuit supervision
• UL Listed under Standard 1480
Speaker Strobes Only
• Synchronized or non-synchronized strobe capability
• Xenon flashtube with solid state circuitry enclosed in a Applications:
rugged Lexan® lens • Use with SP40/2 Multi-Function Facility
• Field selectable candela settings Communications System
• UL Listed under Standard 1971 • Provides for audio quality background music
S p eaker Strobe Approvals

Model Order d B A @ 10 F eet Regulated Voltage
Number C ode Voltage (Rated Watts) UL UL
Voltage R an g e Candela C S FM
(VRMS) 1480 1971
1
/8 1
/4 1
/2 1 2 4 8 VDC/FWR VDC/RMS
S8-70/25 0052 25/70 75 78 81 84 87 90 93 - - - X N/A X
S8-24MCC 0054 25/70 75 78 81 84 87 90 93 24 16.0-33.0 15/30/75/95 X X X
S8-24MCCH 0056 25/70 75 78 81 84 87 90 93 24 16.0-33.0 115/177 X X X
Note: In order to maintain proper UL

1480 listing, the CBB-8 Speaker Back
Box (available separately) or other UL
approved back box must be installed.
Average RMS Current
Strobe
Average 24MCC 24MCCH
RMS * RMS current ratings are per UL average RMS method. UL max current
Current 1 5 cd 3 0 cd 7 5 cd 9 5 cd 115cd 1 7 7 cd rating is the maximum RMS current within the listed voltage range (16-
24 V D C 0.045 0.070 0.119 0.159 0.195 0.270 minimum listed voltage (16v for 24v units). For audibles the max current
UL Max* 0.065 0.105 0.189 0.249 0.300 0.420 unfiltered FWR ratings, see installation instructions.
08/04
Helping People Take ActionSM Series STH Cluster Speaker
Description:
Wheelock’s Series STH Cluster Speakers are designed for high
ambient noise environments. The Cluster Speakers are
available in multiple configurations. Provides high intelligibility
voice reproduction and available high intensity visual alerting
(STH-MSR models) for emergency alarm and protective
signaling.
Features:
• Equipped with UL Standard 1480, STH-15SR horn
loudspeakers
• MSR models are equipped with a UL Standard 1638,
DC-MAX-C Strobe
• Each individual STH-15SR horn is capable of delivering up
to 102 dB at 15 watts at 10 feet
Series STH Cluster
• Omni-directional sound
w/Max Strobe
• DC-MAX-C strobe has a 100 candela strobe at 60 double
flashes per minute
• Speakers and Strobes are prefabricated to a 10” x 10” x 6”
steel enclosure for indoor use
• Mounts to ceiling or wall
• Labor savings – (both time and money)
• Conduit knockouts for ½” or ¾” coupling
• Shipped in one box
Model Order
Description
Number C ode
Speaker/visual systems supplied with four STH-15SR horns and one DC-MAX-C Strobe mounted to a
STH-4MSR 8157
NEMA Type 1 steel enclosure. (red)
Speaker/visual systems supplied with three STH-15SR horns and one DC-MAX-C Strobe mounted to a
STH-3MSR 8156
Speaker/visual systems supplied with two STH-15SR horns and one DC-MAX-C Strobe mounted to a
STH-2MSR 8155
STH-4R 8186 Speaker System supplied with four STH-15SR horns mounted to a NEMA Type 1 steel enclosure. (red)
STH-3R 9753 Speaker System supplied with three STH-15SR horns mounted to a NEMA Type 1 steel enclosure. (red)
STH-2R 9752 Speaker System supplied with two STH-15SR horns mounted to a NEMA Type 1 steel enclosure. (red)
STH-2G 0101 Speaker System supplied with two STH-15SR horns mounted to a NEMA Type 1 steel enclosure. (gray)
Note: Not intended for wash down areas or outdoor applications (See Weatherproof Series).
Note: The Series Cluster Speakers with MAX strobes (STH-4MSR, STH-3MSR & STH-2MSR) are
not intended for UL required Fire Life Safety applications.
Applications:
• Designed for use in Manufacturing Plants, Processing Plants and Factories with high ambient noise levels.
• Hazard warning/alerting
• Industrial audible and visual signaling
• Process control area notification
• Warning lights
• Security alert indication
10/04
Helping People Take ActionSM Series STH Weatherproof
Cluster Speaker
Description:
Wheelock’s Weatherproof Series STH-4M30WC Cluster
Speaker is designed for high ambient noise and outdoor
environments. Provides high intelligibility voice reproduction
and available high intensity visual alerting for emergency
alarm and protective signaling.
Features:
• Equipped with four STH-30, 30 watt horn loudspeakers
• Equipped with UL Standard 1638, DC-MAX-C strobe
• Complies with OSHA 1910.165
• The Series STH-4M30WC appliances are weatherproof
• Capable of delivering over 125 dB @ 30 watts, 1 meter
• Omni-directional sound
• Speakers come preset at 30 watts each Series STH-4M30WC
• DC-MAX-C strobe has a 100 candela strobe at 60 double flashes Weatherproof Cluster
per minute
• Speakers and Strobe are prefabricated to a 13.50” x 15.50” x
6.25” NEMA 4X rated fiberglass enclosure
• Mounts to ceiling, wall or roof
• Labor savings
• Conduit knockouts for ½” coupling
• Shipped in one box

Model Number Order Code Description
Speaker/Visual system supplied with four STH-30 horns

STH-4M30WC 9762 and one DC-MAX-C strobe mounted to a NEMA Type 4X
fiberglass enclosure (gray)
Note: Not intended for wash down areas.
Applications:
• Manufacturing Plants
• Hazard warning/alerting
• Industrial audible and visual signaling
• Process control area notification
• Warning lights
• Security alert indication
• Personnel alerting
• Intrusion warning
• Piers or docks
02/04
Series STH-MCCH Cluster
Speaker with MCCH Strobe
Description:
Wheelock’s Series STH Cluster Speaker with MCCH Multi-
Candela Strobe is designed for indoor ceiling mounting in high
ambient noise environments. Series STH Cluster Speaker with
MCCH Strobe is designed for UL Required Life Safety
applications. Provides high-intelligibility voice reproduction
and high intensity visual alerting for emergency life safety
applications, alarm and protective signaling
Features:
• STH-15SR Speakers are UL Standard 1480 Listed.
• RSS-24MCCH Strobes are UL Standard 1971 Listed
• Compliant with ADA, OSHA 1910.165, ANSI 117.1, NFPA 72,
NFPA 101, and UFC
Series STH-MCCH
• Cluster and Strobe wiring can be monitored for integrity by
the Control Panel
• Cluster Speaker Strobes come fully assembled
• High efficiency unit for fire life safety and/or general Applications for Series Cluster Speaker
communication announcing/notification Strobes:
• Speakers and Strobes are prefabricated to a 10” x 10” x 6” Designed for use in Manufacturing Plants, and
NEMA 1 steel enclosure for indoor use. Factories with high ambient noise levels and
• Mounts to ceiling for UL Required Fire Life Safety Applications.
• Only 1 pair of wires needed for audio connections • Hazard warning/alerting
• Strobes are connected to the NAC Strobe Circuit and are • Industrial audible and visual signaling
selectable 115 or 177 cd • Process control area notification
• Each individual STH-15SR horn is capable of delivering up • Warning lights
to 102 dB at 15 watts at 10 feet • Security alert indication
• Omni-direction • Emergency notification
• Conduit knockouts for ½” or ¾” coupling • Employee notification
• Labor Saving

Supervised Speaker Strobe supplied with four STH-15SR horns and one RSS-24MCCH ceiling strobe
STH-4R24MCCH-NR 3089
mounted to a NEMA 1 steel enclosure. Strobe plate is red with no lettering. (red)
Supervised Speaker Strobe supplied with four STH-15SR horns and one RSS-24MCCH ceiling strobe
STH-4R24MCCH-FR 3090
mounted to a NEMA 1 steel enclosure. Strobe plate is red with FIRE lettering. (red)
Supervised Speaker Strobe supplied with three STH-15SR horns and one RSS-24MCCH ceiling
strobe mounted to a NEMA 1 steel enclosure. Strobe plate is red with no lettering. (red)
Supervised Speaker Strobe supplied with three STH-15SR horns and one RSS-24MCCH ceiling
strobe mounted to a NEMA 1 steel enclosure. Strobe plate is red with FIRE lettering. (red)
Supervised Speaker Strobe supplied with two STH-15SR horns and one RSS-24MCCH ceiling strobe
mounted to a NEMA 1 steel enclosure. Strobe plate is red with no lettering. (red)
Supervised Speaker Strobe supplied with two STH-15SR horns and one RSS-24MCCH ceiling strobe
mounted to a NEMA 1 steel enclosure. Strobe plate is red with FIRE lettering. (red)
Supervised Speaker Strobe supplied with two STH-15SR horns mounted adjacent to each other,
STH-90-R24MCCH-NR 3227 designed for a corner mount configuration and one RSS-24MCCH ceiling strobe mounted to a NEMA
1 steel enclosure. Strobe plate is red with no lettering. (red)
Supervised Speaker Strobe supplied with two STH-15SR horns mounted adjacent to each other,
STH-90-R24MCCH-FR 0522 designed for a corner mount configuration and one RSS-24MCCH ceiling strobe mounted to a NEMA
1 steel enclosure. Strobe plate is red with Fire lettering. (red)
NOTE: Not intended for washdown areas.
10/04
Helping People Take ActionSM Series STH-15S Supervised
Horn Loudspeaker
Description:
Wheelock’s Series STH-15S Supervised Horn Loudspeakers are
equipped with a compression driver providing up to 15 watts
of power handling capability, superior intelligibility and
dispersion to achieve maximum sound projection and
penetration.
Features:
• Approvals Include: UL Standard 1480 – (Speakers for Fire
Protective Signaling Systems), California State Fire Marshal
(CSFM) Series STH-15S
• 15-Watt High Efficiency Compression Driver
• Weather-resistant, vandal-resistant aluminum construction
assures protection against water, humidity, vermin, and
corrosion
• Reentrant acoustic path
• 25/70/100V transformer featuring a screwdriver adjustable,
7 position watt/impedance selection switch
• 5 mfd Capacitor for Line Supervision
• Universal-mounting bracket Series SHMP-R
• Installation terminals and power selector are recessed
mounted, and protected by the metal interface adapter, or
clear plastic shield

Model Order
Description
Number C ode
STH-15S 7937 Supervised, Weatherproof, 15 Watt Horn, Loudspeaker w/ Transformer, Aluminum, Gray
STH-15SR 7938 Supervised, Weatherproof, 15 Watt Horn, Loudspeaker w/ Transformer, Aluminum, Red
UL Listed Adapter Plate, Designed to mount the STH-15SR Horn Speaker (7938) to a
SHMP-R 8154 Series RSSP Strobe Mounting Plate. For Surface Mount Applications, the SBL-2
(6988) Surface Mount Backbox is required.
STH-15S & STH-15SR Power Switch Selections

70.7 Volts 25 Volts 100 Volts
Setting Impedance dB @ dB @ dB @
(Ohm s) Watts 10 Feet Watts 10 Feet Watts 10 Feet
1 5,000 0.9W 90 Not Used Not Used 2.0W 93
2 2,500 1.8W 93 Not Used Not Used 4.0W 96
3 1,300 3.8W 96 0.48W 87 7.5W 99
4 666 7.5W 99 0.94W 90 15.0W 102
5 333 15.0W 102 1.8W 93 Not Used Not Used
6 89 Not Used Not Used 7.5W 99 Not Used Not Used
7 45 Not Used Not Used 15.0W 102 Not Used Not Used
Specifications (UL RATING) Anechoic measurements:

POWER RATING: 15 Watt Continuous 15 watt tap @ 10 feet
FREQUENCY RESPONSE: 400-4,000 Hz Code-3 Tone 107.2 dBA
SENSITIVITY: 102 dB @ 15 Watts @ 10’
Slow Whoop 108.5 dBA
SPECIFICATIONS GENERAL
Siren 107.8 dBA
DISPERSION ANGLE: 70 Degrees (-6 dB @ 2,000 Hz Octave Band)
10/04
Series SA-S Supervised
Self-Amplified Speakers &
Speaker Strobes
Description:
The Series SA-S Supervised Self-Amplified Speakers and
Speaker Strobes are designed to meet the critical needs for
the life safety industry. These 4” speakers and speaker strobes
are a perfect fit for SCIF (Sensative Compartmented Information
Facilities) room applications.
Features:
• Approvals Include: UL Standard 1480 (Speakers) and UL
Standard 1971 and UL Standard 1480 (Speaker Strobes)
• Accepts audio input levels of 0.5 VRMS or 25 VRMS Series SA-S70-24MCW-FR
• Power Input Voltage 16.0 to 33.0 VDC
• 4” Wall or ceiling mount models
• Speaker strobes utilize Wheelock’s synchronizable Multi-
Series SA-S90-24MCC-FW
Candela Strobe (15/30/75/95cd)
• 1 watt high efficiency speaker
• 6 different sound output levels (ranging from 84 to 68 dBA)
• Frequency range of 400Hz to 4000Hz
• Mounts onto a 4” square deep backbox with an extension
ring
Order Wall Ceiling Strobe Mounting
Model Number Color Color
C ode Mount Mount Candela Options# UL MEA CSFM
R ed White
SA-S90-R 1000 - X - X - Q X * *
SA-S90-W 1001 - X - - X Q X * *
SA-S70-R 1002 X - - X - Q X * *
SA-S70-W 1003 X - - X Q X * *
SA-S90-24MCC-FR 1004 - X 15/30/75/95 X - Q X * * #See mounting
options pull out
SA-S90-24MCC-FW 1005 - X 15/30/75/95 - X Q X * * guide in the last
section of this
SA-S70-24MCW-FR 1006 X - 15/30/75/110 X Q X * * binder.
X= Approved
SA-S70-24MCW-FW 1007 X - 15/30/75/110 - X Q X * * *= Pending
Average Strobe RMS Current

Average Speaker Current Draw
SA-S 24MCW 24MCC
24 V D C .120 mA
Models 1 5 cd 3 0 cd 7 5 cd 110cd 1 5 cd 3 0 cd 7 5 cd 9 5 cd
24 V D C 0.041 0.063 0.109 0.140 0.045 0.070 0.119 0.159

UL Max* 0.060 0.092 0.165 0.220 0.065 0.105 0.189 0.249
dB Sound Output**
* RMS current ratings are per UL average RMS method.
SA-S90R UL max current rating is the maximum RMS current within
Sound SA-S90W SA-S90-24MCC-FR SA-S70-24MCC-FR the listed voltage range (16-33v for 24v units). For
Level SA-S70R SA-S90-24MCC-FW SA-S70-24MCC-FW strobes the UL max current is usually at the minimum
SA-S70W listed voltage (16v for 24v units). For audibles the max
current is usually at the maximum listed voltage (33v for
6 84 84 82 24v units). For unfiltered FWR ratings, see installation
instructions.
5 82 81 81 **Rated Reverberant dBA at 10 ft per UL 1480 for 0.5 V
and 25 V settings
4 77 77 76
3 75 74 74
2 71 71 70
1 69 68 68
09/04
Helping People Take ActionSM Series SM & DSM
Synchronization Modules
Description:
Wheelock Series SM & DSM Synchronization Modules provide
the ability to synchronize the strobe flashes and the code 3
temporal evacuation alarm produced by Wheelock
notification appliances. They also provide the ability to silence
the audible alarm while maintaining the strobe flashes over
a single pair of wires.
Features:
• 3 ampere per circuit current handling at 12 or 24 VDC
• Low operating current draw
Series SM & DSM

Order Input Voltage Average Current Mounting
Model Number UL Max*
C ode VD C @ 12 o r 24 V D C Options
SM-12/24-R 6369 12 .017 0.023 W
24 .028 0.038 W
DSM-12/24-R 6374 12 .020 0.026 W
24 .035 0.055 W
Sync Capability
(With SM, DSM, PS-12/24-8CP or PS-12/24-8MP)
Model Audible Strobe Model Audible Strobe
AH-12 Yes - HS-24 Yes -
AH-24 Yes - HS4-241575W Yes Yes
AH-12WP Yes - HS4-24MCW Yes Yes
AH-24WP Yes - HS4-24MCWH Yes Yes
AMT-241575W No Yes MIZ-24S Yes -
AMT-241575W-FR-NYC No Yes MT-121575W No Yes
AMT-2475W No Yes MT-241575W No Yes
AS-241575W Yes Yes MT-2475W No Yes
AS-24MCC Yes Yes MTWP-2475W No Yes
AS-24MCCH Yes Yes NH-12/24 Yes -
AS-24MCWH Yes Yes NS-121575W Yes Yes
CH70-241575W No Yes NS-24MCW Yes Yes
RSS-241575W - Yes
CH7024MCW No Yes
RSS-121575W - Yes
CH7024MCWH No Yes
RSS-24MCC - Yes
CH90-24MCC No Yes
RSS-24MCCH - Yes
CH90-24MCCH No Yes
RSS-24MCCHR - Yes
E70-241575W - Yes
RSS-24MCCR - Yes
E70-24MCW - Yes
RSS-24MCW - Yes
E70-24MCWH - Yes
RSS-24MCWH - Yes
E90-24MCC - Yes
RSSP-121575W - Yes
E90-24MCCH - Yes
RSSP-241575W - Yes
ET-1080-SLM - Yes
RSSP-24MCW - Yes
ET70-241575W - Yes
RSSP-24MCWH - Yes
ET70-24MCW - Yes
RSSWP-2475W - Yes
ET70-24MCWH - Yes
ET90-24MCC - Yes
ET90-24MCCH - Yes
Key: - = Not Applicable to model 08/04

POWERPATH™
SM
Helping People Take Action Series PS-12/24-8CP
and PS-12/24-8MP
Description: Power Supply/Chargers
Wheelock’s Series PS-12/24-8CP and PS-12/24-8MP Power
Supply/Chargers provides 8 amps of regulated 12 or 24 VDC
power for up to 4 Class B or 2 Class A NAC circuits with 3
amps max per circuit. Auxiliary power and synchronization
capability for notification appliances is also provided.
The PS-12/24-8CP provides up to 200 milliamps of continuous
auxiliary output that can be used for control functions during
alarm (or up to 60 milliamps for 60 hour battery requirements).
The PS-12/24-8MP provides up to 3.5 amps of auxiliary output
that is available only during nonalarm condition for such
applications as door holder systems.
Series PS-12/24-8CP
Features:
Series PS-12/24-8MP
• System provides either 12 or 24 VDC inputs and 12 or 24 V
outputs
• Not battery dependent - full 8A even if battery is degraded
• Class 2 rated power limited outputs
• Thermal and short circuit protection with auto reset
• Patented built-in synchronization mode to operate all of
Wheelock’s Synchronized Notification Appliances
Auxiliary Power
• Up to 200mA continuous with PS-12/24-8CP
• up to 3.5 Amps nonalarm with PS-12/24-8MP (e.g. door
holders)

Order Approvals
Model Number Input Voltage
C ode
UL MEA C S FM FM
PS-12/24-8CP 3047 120/220 VAC X * X *
50/60 Hz, 5.0 amps max.
PS-12/24-8MP 3046 X X X X
08/04
Series MPS Manual
Pull Stations
Description:
Wheelock’s Series MPS Manual Pull Stations are constructed
of high quality, die-cast metal for long lasting performance
and may be mounted on a single gang backbox.
Features:
• Single or Dual action
• Key Reset
• Terminal Strip Connections
• Corrosion resistant, gold plated SPST contacts
• Mounts on single gang backbox
• Surface and Weatherproof backboxes available Series MPS-100
• High-gloss red enamel finish with raised white lettering Series MPS-400X
• Approvals Include: Ul Standard, Factory Mutual (FM),
California State Fire Marshal (CSFM) and New York City (MEA)

Model Number Order Code Description Mounting Options
MPS-100 8400 SPST, Single Action, Terminals, Key Reset MPS-ISB, MPS-WP
MPS-200 8401 SPST, Double Action, Terminals, Key Reset MPS-ISB, MPS-WP
MPS-300 8402 DPST, Single Action, Terminals, Key Reset MPS-ISB, MPS-WP
MPS-400X 8403 Explosion Proof, Single Action, Key Reset (Backbox provided)
MPS-ISB 8404 Interior Surface Backbox, Red
MPS-WP 8405 Weatherproof Backbox with Gasket Assembly
MPS-RODS 8406 Scored Acrylic Breakrods (dozen)
02/04
SAFEPATH®4
Helping People Take ActionSM Multi-Function Facility
Communications System
Description:
The SP40/2 is a Multi-Function Supervised Paging, Messaging,
Background Music and Emergency Voice Evacuation System
with 24 VDC battery backup. This single channel system is
capable of delivering 40 watts of supervised high fidelity
audio power and 2 amps of supervised 24 VDC synchronized
strobe power.
Features:
Approv als & Compliance
Approvals
• UL Standard 864, UL Standard 1711, CSFM, FCC Part 15
• OSHA 1910.165 and ADA Compliant SP40/2 SP40/2
Voice Ev acuation
Evacuation Outside Panel Inside Panel
• Complies with NFPA-72 requirements
• Supervised NAC speaker and strobe circuits Strobes
• Live microphone override with on board handheld • 2 Amps of 24 VDC supervised strobe power with
microphone built-in Wheelock sync protocol
• 3 standard digitally prerecorded voice messages • Strobe output is selectable for control of Wheelock
• Messages are field programmable sync protocol or non-sync operation
General Paging • Any of the three messages can be dip switch
• Easily interfaces with most existing phone system selected to activate strobes
page ports and line level signals System Activ ation
Activation
• Automatically mutes background music (BGM) • 9-31 VDC
• Night ringer capability • NAC input from an FACP
• Volume and tone controls Expansion Capabilities
Background Music • 5,280 watt of supervised audio with SPB-80/4 or
• Patent pending supervision with Background Music SPB-160 audio boosters
(BGM) operation • Strobe power expandable to the requirements of
• Line Level input for music source the system with SPB-80/4 or PS-12/24-8MP or
• Volume and tone controls PS-12/24-8CP
• Remote Microphone SPRM
• Speaker Splitter S4PZ-A/B
Specification and Ordering Information: • 3 additional messages SP4-3MEM
Order
Model Number Description
C ode
Multi-Function Supervised Paging, Messaging, Background Music and Emergency Voice Evacuation System with 24
SP40/2 8985 V D C battery backup ci rcui ty. S i ngle channel system wi th 40 watts of supervi sed audi o power and 2 amps of
supervised 24 VDC synchronized strobe power and 3 standard messages. (batteries not included, 2 required)
SPPMK 8987 3 Message Factory Programmed Kit
AM-SPSMK 9902 After Market 3 Message Standard Message Kit
AM-SPPMK 9903 After Market 3 Message Factory Programmed Kit
SP-COA 9908 C.O. Port Adapter for the SP40/2 -Recommended 24 VDC Power Supply is Wheelock RPS-2406 (Order Code 3770)
BAT-1212 7390 12 volt, 12-ampere hour battery
SP4-3MEM-SMK 9913 SP40/2 3 message extender module with standard messages
SP4-3MEM-PMK 9915 SP40/2 3 message extender module with customer programmed messages
Technical Specifications Mechanical Specifications

Switch mode, Class D amplifier (40 Watts) Dimensions 21” H x 16” W x 6” D (wall mount)
Speaker Outputs: 25 V or 70.7 V power limited Weight 36 lbs. (without batteries)
Frequency Response: Voice: 275 Hz – 6.5 kHz ± 3 dB Finish Red metal enclosure with key lock
BGM: 100 Hz - 15 kHz ± 3 dB
Meets UL Voice Evacuation Required batteries fit in the enclosure
Requirements of 400 - 4000 Hz
10/04
Benefits and Adv antages of the Multi-Function SAFEP
Advantages ATH®4
SAFEPA
• One Multi-Function Facility Communications System

• Background Music (BGM), with patent pending supervision during BGM operation
• Supervised Emergency/Fire Voice Evacuation
• Interfaces with telephone system for general paging requirements
• Built in power for visual notification appliances e.g., Strobes
• Expandable for larger system requirements (with optional equipment)
Message Capabilities
A three (3) message Standard Message Kit (SPSMK) is included with the SP40/2.
Message 1: Three (3) rounds of code 3 horn (followed by): “May I have your attention please! A fire emergency has
(FIRE) been reported in the building. While this is being verified, please leave the building by the nearest exit.”
Message 2: Three (3) rounds of code 3 horn (followed by): “May I have your attention please! An emergency has
(ALERT) been reported in the building. While this is being verified, please stand by for further instructions.”
Message 3: Five (5) seconds of 1kHz tone (followed by): “May I have your attention please! The building emergency
(ALL CLEAR) has ended. An all clear has been given. Please resume normal activities.”
• The SP40/2 comes standard with three messages with approximately 20 seconds of time per message (including
tones)
• Any of the three standard messages are field programmable - for recording of custom non-emergency messages -
(requires a 2-step recording process to ensure and verify that the standard emergency message is to be permanently
erased)
• The message memory is comprised of one minute of erasable memory
• Factory Programmed Message Kits (SPPMK) are available for custom messages – contact customer service for
additional information
Note: When ordering Factory Programmed Message Kits SPPMK (8987) or the AM-SPPMK (9903), for custom messages, the messages
can be divided in 20 second blocks with any of the following options:
Option 1 3 messages with a maximum of 20 seconds each (Standard)

Option 2 2 messages, 1 message with a maximum of 40 seconds and 1 message with a maximum of 20 seconds
Option 3 1 message with a maximum of 60 seconds
Contact customer service for additional information.
10/04
4-2 273 Branchport Avenue • Long Branch, NJ 07740 • (800) 631-2148 • www.wheelockinc.com
SAFEPATH®4
SM
Helping People Take Action Audio & Audio/Strobe
Boosters
Description:
Supervised Facility Communication and Emergency Voice
Evacuation Audio and Audio/Strobe Power Boosters, with 24 VDC
battery backup capabilities.
Features:
• The SPB-320, SPB-160 and the SPB-80/4 easily connects to the
Wheelock SP40/2
• Multiple SPB-320, SPB-160 and SPB-80/4 Audio Boosters can
be inter-connected to accommodate large installations with
supervised audio power and also supervised and
synchronized strobe power requirements
Approv als & Compliance
Approvals SPB-160
• UL Standard 864, UL Standard 1711, California State Fire SPB-80/4
Marshal (CSFM)
• OSHA 1910.165 and ADA compliant SPB-320
SPB-80/4 Strobe 320 Watt Supervised Audio Power
• Two 24 VDC 2 Amps, NAC supervised, synchronizable, Booster (Four 80 watt circuits)
power limited, Class B strobe outputs
• Selectable outputs; Wheelock sync, pass through, or SPB-160
constant DC 160 Watt Supervised Audio Power
System Activ ation
Activation Booster (Two 80 watt circuits)
Audio (SPB-320, SPB-160 or SPB-80/4)
• 70 V or 25 V input from the SP40/2 SPB-80/4
Strobe (SPB-80/4) 80 Watt Supervised Audio Power
• 8-33 VDC NAC input contact closure connected to the Booster with 4 Amps of Supervised
strobe input and Synchronizable Strobe Power
(Two 2 Amp circuits)
Specification and Ordering Information:
Model Order
Description
Number C ode
SPB-320* 9918 320 Watt Supervised Audio Power Booster (Four 80 watt circuits)
SPB-160 8989 160 Watt Supervised Audio Power Booster (Two 80 watt circuits)
80 Watt Supervised Audio Power Booster with 4 Amps of Supervised and Synchronized Strobe Power
SPB-80/4 8988
(Two 2 Amp circuits)
SP4Z-A/B 9900 Supervised 2-Zone Class A or 4-Zone Class B Speaker Audio Splitter for the SP40/2 or Boosters
SPMB4Z 9907 Speaker Splitter Mounting Bracket for Boosters
*Available Q3/2004
Technical Specifications
120 VAC, 3.8A, 50-60 Hz input

Mechanical Specifications
Stand by Current Draw: 120mA, per amplifier board
Dimensions 21” H x 16” W x 6” D (wall mount)
Alarm Current Draw: 9 Amps, per amplifier board Weight 36 lbs. (without batteries)
Frequency Response: Voice: 400 Hz – 6.5 kHz ± 3 dB Finish Red metal enclosure with key lock
BGM: 275 Hz - 15 kHz ± 3 dB
Power Limited Circuitry Required batteries fit in the enclosure
Class D Amplifier
Internal battery charger and power supply
Removable quick connect/disconnect terminals, accept 12-22 AWG
Multiple LED's for easy indication of system diagram conditions

08/04
SAFEPATH®4
Helping People Take ActionSM 2-Zone Class A or
4-Zone Class B
Description: Speaker Audio Splitter
Supervised 2-Zone Class A or 4-Zone Class B Speaker Audio
Splitter for the SP40/2, SPB-80/4, SPB-160 or SPB-320.
Features:
Approv
Approvalsals and Compliance
• UL Standard 864 and California State Fire Marshal (CSFM)
• OSHA 1910.165 and ADA Compliant
• In Class A, expand 1 to 2 zones
• In Class B, expand 1 zone up to 4 zones
• Operates on either 25 V or 70.7 V RMS
• Mounts inside the enclosure of either the SP40/2,
SPB-80/4, SPB-160 or SPB-320
• Space provided to allow for naming of the zones SP4Z-A/B
Technical/Electrical Specifications:
• Power and Trouble LED’s
• Individual zone short and open LED indication
• Capable of detecting wiring faults
• Removable wiring terminals for quick connect/disconnect
accepting 12–22 AWG
• All output circuitry is Power Limited
• Operates on 24 VDC, supplied by either the SP40/2,
SPB-80/4, SPB-160 or SPB-320
• 40 watts per zone in Class A
• 20 watts per zone in Class B

Model Order
Description
Number C ode
Supervised 2-Zone Class A or 4-Zone Class B Speaker Audio Splitter for the
SP4Z-A/B 9900
SP40/2, SPB-80/4, SPB-160 or the SPB-320
Mounting Bracket for the SP4Z-A/B is required when used with the SPB-80/4,
SPMB4Z 9907
SPB-160 or the SPB-320
Note: The SP4Z-A/B mounts inside the SP40/2 (a mounting bracket is not
required). When mounting inside the SPB-80/4, SPB-160 or SPB-320, the
additional mounting bracket, SPMB4Z is required and is sold separately.
08/04
SAFEPATH®4
Helping People Take ActionSM Addressable Paging
Splitter and Telephone
Description: Zone Controller
Addressable Paging Splitter and Telephone Zone Controller for
use with the SAFEPATH®4.
Applications:
• Connects to the SP40/2 to control selectable paging
and background music (BGM)
• Ability to access individual or multiple speaker zones
throughout the SP40/2 system via the telephone
SP4-TZC
Features:
• Allows selections of speaker zones via the
telephone keypad (DTMF tones)
• One SP4-TZC (controller) can control up to 17
SP4-APS (splitters)
• Telephone page input connects to stand alone SP4-TZC Telephone Zone Controller:
telephone, unused CO port, page port • Connects to the SP40/2
• USB connection for logical zone grouping and • Auto programmable
BGM programming (supports Windows 2000 and • Custom user programmable (for logical
Windows XP) zones)
• Up to 8 logical zones, a logical zone is a user • All call or selected zone(s) telephone paging
selected group of up to 5 zones (individual or fixed) • Background music (BGM) zone(s) selectable
• RS-485 digital control to the SP4-APS speaker • Telephone input and background music
splitters (BGM) input
• Connects to the SP40/2 via the BGM input • Enclosure for the SP4-TZC (controller):
• The combination of 1 SP4-TZC (controller) and up to Dimensions: 13"H x 7.6"W x 2.15"D
17 SP4-APS (splitters) can provide: Color: Black
Wall mountable
Class B
• Requires 24 VDC, model RPS-2406
4 zones per splitter
Up to 68 individual zones (17 splitters)
17 fixed zones (groups of 4) SP4-APS Addressable Paging Splitter:
8 logical zones • Addressable speaker zone splitter
• Mounts inside the SP40/2, SPB-80/4, SPB-160 or
Class A SPB-320
2 zones per splitter • Operates on 24 VDC, supplied by the SP40/2,
Up to 34 individual zones (17 splitters) SPB-80/4, SPB-160, SPB-320
17 fixed zones (groups of 2) • Handles 40 watts of supervised audio per
8 logical zones zone
• UL Standard 864 listed
Model Order Code Description
SP4Z-APS* 9920 Addressable Paging Splitter
SP4-TZC* 9921 Telephone Zone Controller
TZC-USB* 9923 SP4-TZC Programming Cable
*Available Q4/2004
08/04
273 Branchport Avenue • Long Branch, NJ 07740 • (800) 631-2148 • www.wheelockinc.com 4-4A
SAFEPATH®4
Helping People Take ActionSM Supervised Volume
Control
Description:
Supervised Volume Control for use with the SAFEPATH®4.
Applications:
• Allows manual volume setting for telephone paging and
background music for a specific speaker or speaker zone
• The selected adjustment will not affect the volume setting
of emergency prerecorded messages or live microphone
usage
SP-SVC
Features:
• Supervised volume control for use with UL Listed Life
Safety Applications
• Can handle up to 35 watts of audio power input
• Operates on either 70.7 or 25 volt audio input from
an SP40/2 or Audio Booster
ary
• Adjustment settings: off, 1 – 10, in 3dB increments
• Operates in Class B or Class A wiring (for Class A,
imin
the SP4-APS is required)
•· Requires a double gang, 3½" deep back box
Pre
• Stainless steel mounting plate with a black knob
• UL Standard 1480 listed
l
• OSHA 1910.165 and ADA compliant
Order
Model D escription
C ode
Supervi sed Volume C ontrol for

SP-SVC * 9926
use wi th the SP40/2
*Available Q1/2005
08/04
273 Branchport Avenue • Long Branch, NJ 07740 • (800) 631-2148 • www.wheelockinc.com 4-4B
SAFEPATH®4
Helping People Take ActionSM Remote Microphone &
SPRM Remote Microphone
Description: Expansion Module
Remote Microphone for use with the SP40/2 Facility
Communications System.
Features:
Approv als
Approvals
Activation
Activation
• Supervised hand held push to talk microphone
• Key required to enable remote microphone use (same key
as SP40/2)
• When used with the SP40/2, the priority level is 2, the SP40/2 SPRM
on board microphone is priority 1
• Remote microphone usage disengages background music SP4-RMX
and general paging
SP4-RMX
Technical/Electrical Specifications:
Description:
• Voice frequency response: 275 Hz - 6.5 kHz +/- 2.4dB
Remote Microphone Expansion Module.
• Individual front panel LED indication for System Normal,
System Trouble, Alarm
Features:
• Multiple on board diagnostic LED’s
Approv als
Approvals
• Removable wiring terminals for quick connect/disconnect
• UL Standard 864 and California State Fire
accepting 12-22 AWG
Marshal (CSFM)
• 6 wire connection to the SP40/2
• Mounting plate is red and measures, 8 ¾" x 5 ¼”, fits into
a 4 gang back box Applications
• All output circuitry is Power Limited • Expands one remote microphone (SPRM) from
• Operates on 24 VDC, supplied by the SP40/2 the SP40/2 to three remote microphones
• Two SP4-RMX modules can be ganged
together to provide up to six remote
microphones from the SP40/2
Model Order • Provides for an auxiliary input for connection
Description
Number C ode of an external message repeater for additional
messages
SPRM 8996 Remote Microphone for use with the SP40/2
SP4-RMX* 9919 Remote Microphone Expansion Module
*Available Q3/2004
08/04
SM
SAFEPATH® Dual Circuit
Supervised Voice/Audio
Evacuation & Paging System
Description:
The DCSP is a supervised dual circuit voice evacuation and
general paging system.
Features:
Approv als
Approvals
System Dual Circuit
• Dual channel; prerecorded messages can be broadcast over SAFEPATH®
two separate zones simultaneously
• Supervised Speaker and Strobe circuits
• 2 amps of 24 VDC synchronized strobe power per circuit
• Live microphone override with on board handheld
microphone
• 8-tone tone generator
SAFEPATH® Includes
Dual Circuit SAFE
Technical/Electrical Specifications: • DCSP-R: Dual Circuit Modules - Red Enclosure
• Message contacts (maximum of 8) • MDX-2: 2 Channel Digital Voice Output Module
- Contact closure/open collector of a transistor • SMK: Standard Message Kit (8 messages)
• Notification Appliance Circuit Interface module (NACIM) • MIC-400: Handheld Microphone
Expansion Capabilities • DCPS: 6 Amp, 25 V Power Supply/Charger
• Additional SAA amplifier card (SAA-40S, SAA-80S, • Choice of 40 watt, 80 watt or Line Level Amplifier
SALL-15S) • Enclosure: 21”H x 16”W x 6”D
• Remote microphone (RMS-3)
• Auxiliary Input Module (AIM-3) Note 1: External battery enclosure is required
• Four Zone Audio Splitter (SPL) Note 2: One amplifier is included, additional amplifier
may be purchased separately
• Remote SafePath (RSAPE-R)
Note 3: If using strobe output and audio power
- Can be expandable to 2,560 watts exceeds 80 watts, consult with technical
support for proper layout
Model Order
Description
Number C ode
DCSP-4RP 8954 40 Watt Dual Circuit Packaged SAFEPATH®
DCSP-8RP 8955 80 Watt Dual Circuit Packaged SAFEPATH®
DCSP-15SP 8970 Line Level Output Dual Circuit Packaged SAFEPATH®
Technical Specifications Mechanical Specifications

• Switch mode Class D 40 or 80 watts or line level Dimensions: 21” H x 16” W x 6” D (wall mount)
• Speaker outputs 25 V or 70.7 V or line level
• Frequency response 250 – 10kHZ Weight: 60 lbs. (without batteries)
• Meets UL Voice Evacuation requirements of 400 – 4000Hz Finish: Red metal enclosure with key lock
08/04
SM
SAFEPATH® Multi-Circuit
Description:
The SAPE is a supervised multi circuit voice evacuation and
general paging system.
Features:
Approv als
Approvals
System
• Four channel; prerecorded messages can be broadcast over
four separate zones simultaneously
• Live microphone override with on board handheld
microphone Multi-Circuit
• 8-tone tone generator SAFEPATH®
• SAPE-1AR with playback module
• SAPE-2AR with message recording and playback module
Activ ation
Activation
• Message contacts (maximum of 256)
- Contact closure/open collector of a transistor
• RS-232 or RS-485 interface, message contacts expanded
to up to 999
• Notification Appliance Circuit Interface module (NACIM)
Expansion Capabilities
• Up to four SAA amplifier cards (SAA-40S, SAA-80S,
SALL-15S) Technical Specifications
• Remote microphone (RMS-1) • Switch mode Class D 40 or 80 watts or line level
• Auxiliary Input Module (AIM-3) • Speaker outputs 25 V or 70.7 V or line level
• Four Zone Audio Splitter (SPL) • Frequency response 250 – 10kHZ
• Remote SafePath (RSAPE-R) • Meets UL Voice Evacuation requirements of 400 – 4000Hz
- Can be expandable to 5,120 watts
Note: Amplifier cards and message
kits sold separately
Model Order
Description
Number C ode
SAPE-1AR 5443 Multi-circuit System with DX-100 Playback Module, Red
Multi-circuit System with DX-200 Record & Playback (field programmable)
SAPE-2AR 5445
Module, Red
Multi-circuit SAFEPATH® Output Channel Kits
OCK 5057 Output Channel Kit for SAPE-1AR (DX-100) or SAPE-2AR (DX-200)
AM-OCK 5063 After Market Output Channel Kit for SAPE-1AR (DX-100) or SAPE-2AR (DX-200)
Additional Memory
MEM-1 5054 1 minute of EPROM Memory (2 megs) for SAPE-1AR
MEM-2 5055 2 minutes of PSRAM Memory (4 megs) for SAPE-2AR
AM-MEM-1 5060 After Market 1 minute of EPROM Memory (2 megs)
AM-MEM-2 5061 After Market 2 minutes of PSRAM Memory (4 megs)
Dimensions: 36” H x 24” W x 6” D (wall mount)
Weight: 70 lbs. (without batteries)
Finish: Red metal enclosure with key lock
08/04
SM
SAFEPATH® Remote Circuit
Description:
The RSAPE is a remote supervised multi circuit voice evacuation
and general paging system, used for expansion of the DCSP or
SAPE.
Features:
Approv als
Approvals
System
• Four channels
• Live microphone override with on board handheld Remote Circuit
microphone SAFEPATH®
Activ ation
Activation
• Receives activation signals from the DCSP or the SAPE
• Plays messages from the DCSP or the SAPE
Expansion Capabilities
• Up to four SAA amplifier cards (SAA-40S, SAA-80S,
SAA-15S)
• Remote microphone (RMS-1)
• Auxiliary Input Module (AIM-3)
• Four Zone Audio Splitter (SPL)
Model Order
Description
Number C ode
RSAPE-1AR 7365 Remote Multi-circuit SAFEPATH System, Red
• Switch mode Class D 40 or 80 watts or line level
• Speaker outputs 25 V or 70.7 V or line level
• Frequency response 250 – 10kHZ
• Meets UL Voice Evacuation requirements of 400 – 4000Hz Note: Amplifier cards sold separately.
Dimensions: 36” H x 24” W x 6” D (wall mount)
Weight: 70 lbs. (without batteries)
Finish: Red metal enclosure with key lock
08/04
SAFEPATH®
Remote Microphones
Description:
Remote Microphones for use with Dual Circuit , Multi-circuit and
Remote SAFEPATH systems.
RMS-1R and RMS-3R

Features:
Approv als
Approvals
System
• Supervised handheld push to talk microphone
• Key required to enable remote microphone use
RMS-1R
RMS-3R
• Frequency response 250-6.5kHz
• Meets UL Voice Evacuation requirements of 400-4000Hz
• Individual front panel LED indication for System Normal,
System Trouble, Alarm
• Operates on 24 VDC, supplied by the SAFEPATH® panel
• Terminals accept 12-22 AWG
• Measures 8¾” x 5¼”, fits into a 4 gang back box SD-RMS-1RM
SD-RMS-1RMB
Features:
• Up to five prerecorded messages can be activated
• Prerecorded messages/tones can be activated by five
independent latching push buttons
• One reset button
• Four zone selectable switches and all call switch
• Removable push-to-talk, handheld microphone with
supervised circuitry
• Status and zone LED’s
• Removable terminal block connector for easy installation
• 19” Rack Mountable (2 RU) with matte black faceplate - can
be console mounted
• Built-in preamplifier
Order
C ode
Special Design Rack Mount Remote Microphone
SD-RMS-1RMB 8962
Station with 5 message activation buttons
RMS-3R 7375 Dual Circuit Remote Microphone Station, Red
RMS-1R 5473 Multi-Circuit Remote Microphone Station, Red
08/04
SAFEPATH® DSCP, SAPE,
RSAPE Modules, Message
Kits & Batteries
Specifications and Ordering Information:

Model Order
Description
Number C ode
SAFEPATH® Amplifiers
SAA-40S 5493 40 Watt Supervised Audio Amplifier and 2 Amps of Supervised NAC Strobe Circuit Power Module
SAA-80S 5495 80 Watt Supervised Audio Amplifier and 2 Amps of Supervised NAC Strobe Circuit Power Module
80 Watt Supervised Audio Amplifier and 2 Amps of Supervised NAC Strobe Circuit Power Module
SAA-80SE 5496
(E= Export version)
SALL-15S 5497 Supervised Audio Line output module and 2 amps of Supervised NAC Strobe Circuit Power Module
®
SAFEPATH Auxillary Input Module, Splitters & Notification Appliance Circuit
Auxillary Input Module for Telephone System Interface & Multiple Remote Microphones. It allows the number
AIM-3 7387 of Remote Microphone Stations to be expanded from one to three or allows the interface of telephone
systems for paging and 2 remote mics.
NACIM 5498 Notification Appliance Circuit Interface Module
SPL 7369 Dual or Multi-Circuit Speaker Circuit Splitter (4-way)
Standard Message Kits
SMK 5082 Standard Message Kit (8 most common messages)
SMK-OSHA 8191 Standard Message Kit for OSHA Applications (8 OSHA related messages
SMK-SP 8144 Spanish Standard Message Kit (8 most common messages)
SMK-ENGSP 8148 English & Spanish Standard Message Kit (8 most common messages)
AM-SMK 7599 After Market Standard Message Kit (8 most common messages)
AM-SMK-OSHA 8192 After Market Standard Message Kit for OSHA Applications (8 most common messages)
AM-SMK-SP 8117 After Market Spanish Standard Message Kit
AM-SMK-ENGSP 8149 After Market English/Spanish Standard Message Kit
Common Message Kits
CMK 8193 Common Message Kit, customer choice of any 3 messges from library of 25 commonly used messages as
listed on form PMKOF
AM-CMK 8194 After Market Common Message Kit, customer choice of any 3 messages from library of 25 commonly used
messages as listed on form PMKOF
Programmed Message Kits
MDV-PMK 5099 1 minute of factory programmed memory
PMK 5056 Factory Programmed Message Kit
AM-MDV-PMK 5089 After Market MDV Factory Programmed Message Kit
AM-PMK 5062 After Market Factory Programmed Message Kit
AM-TMK 8975 After Market Factory Programmed Message Cassette Tape Kit
Batteries & Battery Cabinets
BATC-B 5413 Battery Cabinet, Black (9.5"H x 24"W x 9" D)
BATC-R 5414 Battery Cabinet, Red (9.5"H x 24"W x 9" D)
BAT-1212 7390 12 Volt, 12 Ampere Hour Battery Cell
08/04
Helping People Take ActionSM SAFEPATH® & VoiceLink
Messages
Specifications and Ordering Information:

SMK and AM-SMK Standard Messages in Standard Message Kit
Message # Message Script
1 (3 rounds of code 3 horn) "May I have your attention please! A fire emergency has been reported in the building. While
this is being verified, please leave the building by the nearest exit. Do not use the elevators."
2 (5 seconds of 1kHz tone) "May I have your attention please! A fire emergency has been reported in the building. While
this is being verified, please standby for further instructions."
3 (3 rounds of code 3 horn) "May I have your attention please! An emergency has been reported in the building. Please
leave the building by the nearest exit or exit stairway. Do not use the elevators."
4 (3 rounds of code 3 horn) "May I have your attention please! An emergency has been reported in the building. While
this is being verified, please leave the building and report to the designated assembly area for your group."
5 (5 seconds of 1kHz tone) "May I have your attention! The National Weather Service has issued a severe weather warning
for our area."
6 (5 seconds of 1kHz tone) "This is an audio system test."
7 (5 seconds of 1kHz tone) "May I have your attention please! The building emergency has ended. An all clear has been
given. Please resume normal activities."
8 (3 rounds of code 3 horn) "May I have your attention please! A fire emergency has been reported in the building. While
this is being verified, please leave the building by the nearest exit."
SMK-OSHA and AM-SMK-OSHA Standard Messages in OSHA Applications Message Kit

Message # and Type Message Script
1 (1 round of code 3 horn) "Attention, Attention, a fire emergency has been reported. Please leave the building
Fire Emergency using the nearest exit."
2 (5 seconds slow whoop) "May I have your attention please! A medical emergency has been reported, all
Medical Emergency EMT personnel report to your assigned stations."
3 (5 seconds fast whoop) "Attention, Attention. A toxic chemical realease has been reported, all personnel are
Toxic Chemical Release to report to their designated emergency areas and await further instructions."
4 (5 seconds, 1,000hz steady tone) "The National Weather Service has issued a tornado alert for this area,
Tornado Watch further information will be broadcasted as it becomes available."
5 (5 second wail) "A flash flood watch has been issued by the local weather service, further information will be
Flood Watch broadcasted as it becomes available."
6 (5 second chime) "The building emergency has now ended, please resume your normal duties. Thank you
All Clear for your coorperation."
(5 second hi-lo) "Attention, Attention, a bomb threat alert has been issued for this building, all personnel are
7
to evacuate immediately using the nearest exit. Further instructions will be issued outside the building by
Bomb Threat
emergency response teams."
(5 seconds fast whoop) "May I have your attention please, a terrorist threat hass been received. Effective
8
immediately we are operating "secure and lockdown procedures. All personnel should remain calm and stay
Terrorist Threat
where you are. Emergency response teams are active within the building. Please await further instructions."
• Custom programmed messages and or tones are

available
• All messages are available in both male or female voice.
Male voice will be assumed unless otherwise specified
• Contact customer service for additional information and
Wheelock form PMKOF
08/04
VoiceLink Multi-Message,
Monitoring & Reporting
Systems
Description:
VoiceLink is a digital multi-messaging system designed to
automatically deliver instant real voice custom prerecorded
messages. VoiceLink can provide specific information such as
emergency or special announcements, instructions, directions,
or advertisements. VoiceLink systems have a line level output
for connection to PA systems.
Features:
Approv als
Approvals
• UL Standard 864, California State Fire Marshal (CSFM), ULC,
New York City (MEA), FCC
DV-200
General MDV-2
• Up to 5 levels of priority can be programmed
• Connectable to any paging system, telephone dial-out system,
pagers, or two-way radios DV -200 Field Programmable Four Channel
DV-200
• Operates on any regulated and filtered 11-29 VDC power multi-message record and playback system
supply (Wheelock RPS-2406) • One channel standard, expandable to 2
• Announcements can be activated via contact closure or open channels by utilizing OCK or AM-OCK modules
collector of a transistor • 8 message file contacts, expandable up to 256
MDV
MDV-2 -2 TTwo
wo channel multi-message playback system message contacts utilizing DV-EM expansion
• One channel standard, expandable to 2 channels by utilizing modules
an additional module AM-MDV-OCM • Up to 999 files can be accessed via RS-232 or
• 8 message file contacts RS-485 activation
• 1 minute of digital EPROM memory, expandable to 2 minutes • 2 minutes of digital PSRAM memory, expandable
utilizing an additional module MDV-PMK to up to 16 minutes utilizing additional MEM-2
• Voice messaging system for DCSP SAFEPATH® Voice modules
Evacuation System • Voice messaging system for SAPE-2AR
SAFEPATH® Voice Evacuation System
DV -100 Four Channel multi-message playback system
DV-100
• One channel standard, expandable to 4 channels by utilizing
OCK or AM-OCK modules Audio/Technical Specifications
• 8 message file contacts, expandable up to 256 message Output: 600 ohms
contacts utilizing DV-EM expansion modules
Frequency
• Up to 999 files can be accessed via RS-232 or RS-485 activation Response: 70-3kHz
• 1 minute of digital EPROM memory, expandable to up to 8
minutes utilizing additional modules PMK
• Voice messaging system for SAPE-1AR SAFEPATH® Voice Wall mountable black enclosure
Evacuation System MDV-2: 13" H x 8" W x 2" D
DV-100: 14" H x 12" W x 2" D
DV-200: 18" H x 18" W x 3" D
Model Order
Description
Number C ode
SAFEPATH® Systems utiliz e VoiceLink modules denoted by model numbers
MDV-2 5093 2 Channel, multi-message playback system (used in Dual Circuit SAFEPATH® systems - MDX-2)
DV-100 5051 4 Channel, multi-message playback system (used in Multi-Circuit SAFEPATH® systems - DX-100)
DV-200 5052 4 Channel, multi-message playback/record system (used in Multi-Circuit SAFEPATH® systems - DX-200)
08/04
Typical Applications using VoiceLink Systems:
VoiceLink
• Emergency Announcements or Fire Alarm Voice Evacuation Messages can be automatically
broadcast through the fire alarm voice system for immediate evacuation and safety
• Manufacturing and process control equipment can be monitored and instant message
can be sent to the supervisor via voice paging, two-way radio or pager in the event of
a malfunction.
• Alert emergency brigades to respond quickly in case of employee accidents.
• Automatically warn employees or visitors of hazardous or restricted access areas.
• Notification of customer assistance in retail store applications.
• Intelligible Nurse Call reporting, Code Blue.
VoiceLink systems can be used in these applications as well:

Automatic Paging
Restricted Access Notification
Arrival & Departure Announcement
Emergency Assistance
Informing of Special Events
Directory Assistance
Airport trams/luggage carousels
Workforce Shift and Break Notice
Classroom Changes
Security Reporting
Area Restriction Warning
Inmate Control, Man Down Systems
Elevator Floor Annunciation
Route and Delay Notification
In Store Sales Announcements

Model Order
Description
Number C ode
Expansion Modules, Memory and Progamming Accessories
DV-EM 5053 32 Input Expansion Module-maximim of 8 per system Enclosure: 12" H x 6" W x 2" D
CAB-EM 5066 Expansion cable for connecting a DV-100 or DV-200 to the first DV-EM
CAB-P 5067 Programming Cable or DV-100 from DV-200
MEM-1 5054 1 minute of EPROM memory (2 megs), For DV-100, used for the SAPE-1AR
MEM-2 5055 2 minutes of PSRAM memory (4 megs), For DV-200, used for the SAPE-2AR
AM-MEM-1 5060 After Market 1 minute of EPROM memory, For DV-100, SAPE-1AR
AM-MEM-2 5061 After Market 2 minutes of PSRAM memory For DV-200, SAPE-2AR
BAT 5069 Spare battery pack for memory retention For DV-200, SAPE-2AR
MIC 5068 Replacement Programming Microphone For DV-200
Output Channel Kits, End of Line Resistors and Pow er Supply
OCK 5057 Output Channel Kit - first channel supplied with system (maximum of 4 OCK's per system) For DV-100, DX-100, DV-200, DX-200
AM-OCK 5063 After Market Output Channel Kit For DV-100, DX-100, DV-200, DX-200
AM-MDV-OCM 5097 After Market MDV Output Channel Module - required for 2nd output channel on the MDV-2
EOLK 5076 Endl of line resistor kit (8 UL Listed end of line resistors)
EOLK-EM 5077 End of line resistor kit for DV-EM expansion moudle (32 UL Listed end of line resistors)
RPS-2406 3770 24 VDC power supply (for non-UL-Fire applications)
Programmed Message Kits
MDV-PMK 5099 1 minute of factory programmed memory
PMK 5056 Factory Programmed Message Kit
AM-MDV-PMK 5089 After Market MDV Factory Programmed Message Kit
AM-PMK 5062 After Market Factory Programmed Message Kit
08/04
4-15 273 Branchport Avenue • Long Branch, NJ 07740 • (800) 631-2148 • www.wheelockinc.com
Series NPS
Push Stations
Description:
Multipurpose push stations for manual activation of
SAFE
SAFEPATH® and SAFEP
SAFEPAATH ®4 Voice Evacuation Systems
prerecorded messages. Can be used to manually activate
a message in the event of an emergency or for alerting. These
multipurpose push stations are for applications that need
Normally Open or Normally Closed contacts.
Features:
• Approvals Include: UL Standard S2017 switch assembly
• Available in five colors: Red, Green, Yellow, White, or Blue
• Custom wording available
• Polycarbonate faceplate NPS Push
• Stainless steel backplate Stations
• ADA Compliant
• Mounts to single gang electrical box
• Double pole, double throw terminal block rated for 3 amps
@ 600 VDC or 1 Amp @ 250 VDC
• Can be reset by depressing the “Push” button, and turning
clockwise ¼ turn

Model Order Model Model
Color Description Wording Wording
Number C ode Code Suffix Code Suffix
NPS-R 9767 Red Push Station for manual message activation Land Attack -001 Emergencia -026
NPS-G 9768 Green Push Station for manual message activation Sea Attack -002 Alarm Yellow -027
NPS-Y 9769 Yellow Push Station for manual message activation Colors -003 Delta -028
NPS-W 9770 White Push Station for manual message activation Alarm Red -029
Low Threat -004
NPS-B 9771 Blue Push Station for manual message activation
Medium Threat -005 Withdrawal -030
NPS-NO 0523 Push Station Normally Open Contact
High Threat -006 Emergency -031
NPS-NC 0524 Push Station Normally Closed Contact
Small Craft -007 Audio Test -032
Unknown Object -008 All Clear -033
Code Bravo -009 Fire Test -034

Wording Matrix for top of the Push Station Low -010 Evac Drill -035
Any “wording suffix” can be printed on any color push
Medium -011
station.
Examples: High -012
9767-003 NPS-R-003 Red Push Station, Colors Water Attack -013
9771-010 NPS-B-010 Blue Push Station, Low
Chemical Spill -014
Gas Release -015
Note: Custom wording is available,
Evacuation -016
please contact customer service.
Help -017
Assistance -018
Severe Weather -019
Tornado -020
Medical Alert -021
Power Shut Down -022
Blank/No Wording -023
Strobe -024
Alert -025
08/04
Series MAX Industrial
Strobes AC-MAX, AC-MAXS
DC-MAX & DC-MAXS
Description:
High Intensity, weather-resistant visible warning signals, designed
for stationary or mobile use. Applications for Series MAX strobes
include hazard warning/alerting, industrial visual signaling, strobe
beacons for vehicles or equipment, process control area
notification, access gate/loading dock identification, and outdoor
emergency (fire, security) strobe. Applications for Strobe and
Steady Light Models include location of specific equipment, eye
wash station/emergency medical kit location, emergency phone
location, warning lights and security alert indication.
Features:
• UL Standard 1638 Listed for indoor or outdoor use
• AC-MAX and AC-MAXS models are for 120 VAC applications
• DC-MAX and DC-MAXS models are for DC applications DC Series AC-MAX-B
voltage range: 10.5 VDC to 31.0 VDC
• Powerful double flash light burst
• 60 double flashes per minute
• Available lens colors per SAE specifications: Amber, Blue, Clear,
Red
• Durable, high impact Lexan® lens construction
• Mounting options: 1/2 inch pipe, surface mount, flange mount, Features for Steady Light Models (MAXS):
standard 4-inch square electrical box or Wheelock WBB Weather • Two 7 watt incandescent lamps
Resistant Backbox (order code 2959) • Independent wiring for electrical hookup
• Overall height: 5 inches
• Diameter: 6.2 inches
• Weight: 2 lbs.

Model Order L en s Effective
Voltage Product Description
Number C ode Color Candela (cd)
AC-MAX-A 8120 Amber 120 VAC Double Flash MAX Strobe 80
AC-MAX-B 8121 Blue 120 VAC Double Flash MAX Strobe 12
AC-MAX-C 8122 Clear 120 VAC Double Flash MAX Strobe 100
AC-MAX-R 8124 Red 120 VAC Double Flash MAX Strobe 20
Double Flash MAX Strobe w/ Model C urrent D raw
AC-MAXS-A 8125 Amber 120 VAC 80
two 7 watt steady light lamps
AC -MAX and AC -MAXS 0.20 @ 120 VAC
Double Flash MAX Strobe w/
AC-MAXS-B 8126 Blue 120 VAC 12
two 7 watt steady light lamps 1227 mA @ 10.5
Double Flash MAX Strobe w/ VD C
AC-MAXS-C 8127 Clear 120 VAC 100 D C -MAX and D C -MAXS 1010 mA @ 12 VD C
470 mA @ 24 VD C
Double Flash MAX Strobe w/ 344 mA @ 31 VD C
AC-MAXS-R 8129 Red 120 VAC 20
Steady Light Lamps C urrent D raw
DC-MAX-A 8130 Amber 10.5-31.0 VDC Double Flash MAX Strobe 80
DC-MAX-B 8131 Blue 10.5-31.0 VDC Double Flash MAX Strobe 12 AC -MAXS Models 120 mA
DC-MAX-C 8132 Clear 10.5-31.0 VDC Double Flash MAX Strobe 100 D C -MAXS Models 665 mA
DC-MAX-R 8134 Red 10.5-31.0 VDC Double Flash MAX Strobe 20

Double Flash MAX Strobe w/ DC Inrush Current Draw:
DC-MAXS-A 8135 Amber 10.5-31.0 VDC 80
two 7 watt steady light lamps 12V 5A Max
DC-MAXS-B 8136 Blue 10.5-31.0 VDC
12 24V 10A Max
31V 12A Max
DC-MAXS-C 8137 Clear 10.5-31.0 VDC 100
two 7 watt steady light lamps Note:
Double Flash MAX Strobe w/ Series MAX Strobes are not intended for
DC-MAXS-R 8139 Red 10.5-31.0 VDC 20
use in wash down areas.
02/04
Series MT & MT Strobe
Multitone Electronic
Signals
Description:
Wheelock’s Series MT and MT Strobe Multitone electronic
signals offer a choice of eight (8) alerting sounds: Horn, Bell,
March Time Horn, Code-3 Tone, Code-3 Horn, Slow Whoop,
Siren or Hi/Lo Tone. One alarm appliance can provide
superior sound penetration for various ambient and room
conditions with two field selectable sound output levels.
Features:
• UL Standard 464, 1638 and 1971 Listed
• 12 VDC and 24 VDC and 115 VAC models available
• Low cost and easy installation via standard electrical boxes. Series MT-121575W-NW
Attractive flush or surface mounting options MTWP-2475W-FW
• No additional trimplate required for flush mounting. Easy
installation with screw terminals accepting #12 to #18 AWG
wire
• Strobe models available with 15 candela rating for
Series MT4-115-WH-VNS
independent or single input activation
• Audible and strobe can operate from a single signaling
circuit with any of the (8) audible alerting sounds
• White Plate

Order Input Mounting Agency Approvals
Model Number Rated Candela
C ode Voltage Options# UL MEA CSFM FM B FP
MT-12/24-W 5024 12/24 VDC - D,E,F,G,L,M,O,R X X X X X
MT4-115-S 6142 115 VAC - D,E,J,K,N,O,R X X X X X
MT-121575W-NW 9747 12 V D C 15 (75 on Axis) D,E,F,G,L,M,O,R X X X X *

#See mounting options pull out guide
MTWP-2475W-NW 9744 24 V D C 75 M X X X X * in the last section of this binder.
MT4-115-WH-VNS 6143 115 VAC 15 D,E,J,K,N,O,R X X X X X X = Approved
* = Pending
MT-24MCW-NW 3305 24 V D C 15/30/75/110 D,E,F,L,M,O,P,R X * X * *
dBA and Current Ratings for Multitone Audible Portion

Average Current Ratings (AMPS) dBA Reverberant Ratings Per UL 464 dBA Anechoic Ratings
Tone
@ 24 V D C @ 12 V D C @ 24 V D C @ 12 V D C @ 12 and 24 VDC
HI STD HI STD HI STD HI STD HI STD
Horn 0.038 0.024 0.095 0.019 92 87 90 77 99 93
Bell 0.019 0.012 0.030 0.010 86 80 85 69 92 87
March Time Horn 0.038 0.024 0.095 0.019 89 84 89 74 99 93
Code-3 Horn 0.038 0.024 0.095 0.019 88 83 88 73 99 93
Code-3 Tone 0.027 0.016 0.057 0.014 85 80 84 70 95 90
Slow Whoop 0.047 0.025 0.095 0.024 90 89 89 75 99 94
Siren 0.034 0.022 0.078 0.019 89 84 89 75 98 93
Hi/Lo 0.020 0.013 0.042 0.011 86 81 86 71 93 88
Tone Pattern Description Tone Pattern Description

Horn Broadband Horn (Continuous) Code-3 Tone 500 Hz (ANSI S3.41 Temporal Pattern)
Bell 1650 Hz Modulated (0.7 sec. On/Repeat) Slow Whoop 500-1200 Hz Sweep (4.0 On/0.5 sec. Off/Repeat)
March Time Horn Horn (0.25 sec. On/0.25 sec. Off/Repeat) Siren 600-1200 Sweep (1.0 sec. On/Repeat)
Code-3 Horn Hornh (ANSI S3.41 Temporal Pattern) Hi/Lo 1000/800 Hz (0.25 sec. On/Alternate)
All MT and MT4 strobe models for outdoor use are Listed for -31°F to 150°F (-35°C to 66°C) and maximum humidity of 95% RH.
10/04
Series WH Remote Strobes
Description:
The Series WH remote strobes feature a xenon flashtube housed
in a polycarbonate lens. They deliver a high intensity flash and
can be used to provide visual alerts for personnel or visitors in
the workplace
Features:
• UL 1638 Listed
• Models available in 115 VAC
• WH1T flush mounts to single gang backbox
• WH3T surface mounts to 4” square backbox or WBB back box Series WH3T Series WH1T
for outdoor use

Model Order Strobe Current
Voltage Mounting Options
Number C ode Candela Draw
WH1T-115-NS 3515 115 VAC 15 0.06 B

WH3T-115-NS 3563 115 VAC 15 0.06 K, N
Description:
The Series MTH-24 Multi-Tone Horn is a loud, weather resistant,
attention getting alert designed for use in noisy or large
locations where two different audible signals are required at MTH-24 Multitone Horn
one location for easy identification of the alert signal.
Features:
• Functions as a telephone extension alert using a pulsed
warble tone activated by the telephone systems interrupted
or continuous dry contact closure
• Functions as an auxiliary alert using a steady tone which
follows the contact closure of a door service push-button,
time clock, alarm systems, etc.
• When both alerting tones are activated, the steady tone
will take priority over the warble tone
• Built in 10-watt amplifier, electronic dual tone generator
(steady or warble), timer for the warble circuit, and volume
control
• 117 dBA @ 1 meter Series MTH-24
• Includes RPS-2406, 24 VDC, 600 mA power supply
• Universal mounting bracket
• If an analog ring voltage (direct telephone line or PABX
extension) is present, use the CRT-T-40 telephone relay to
develop a dry contact for controlling the Series MTH-24
Multitone Horn
• The recommended replacement of the Series 163
telephone signaling package is as follows:
• MTH-24 • CRT-T-40
Model Order Nominal Operating Max. Operating dB A @

Type
Number C ode Voltage Current @ 24 VDC 1 meter
Weatherproof for Indoor and or

MTH-24 3801 24 V D C 600mA 117
Outdoor Installation
08/04
Series AMT & AMT Strobe
Multiple Input Multitone
Electronic Signal
Description:
Wheelock’s Series AMT Multiple Input Electronic Signals
provide a combination audible/visual device that simplifies
installation and offers three (3) distinct prioritized audible
signals from three isolated inputs. Priority one (1) will override
all other commands upon activation. The AMT offers a choice
of nine (9) self-prioritized sound combinations for suppression
releasing systems, combination security and OSHA
emergency evacuation systems and high risk installations
as well as many other industrial applications.
Features:
• UL Standard 464 and 1971 Listed
• Three separate prioritized inputs that will activate three
isolated signals
• Two field selectable sound output levels
Series AMT-241575W-NW
• Low current draw with low temperature compensation to
reduce power consumption and wiring costs
• Combination audible/visual model with 15 candela strobe
• Low cost installation via standard electrical boxes
• White plate

Model Order Input Rated Mounting Agency Approvals
Number C ode Voltage Candela Options#
UL MEA C S FM FM B FP #See mounting options pull out
guide in the last section of this
AMT-12/24-W 5893 12/24 VDC N/A E,F,L,M,O,P X X X X X binder.
AMT-241575W-NW 3047 24 V D C 15 E,F,L,M,O,P X X X X * X = Approved
* = Pending
Current Ratings for AMT Multitone Audible Signals AMT dBA Ratings AMT w / Strobe
Typical Anechoic Typical Anechoic
Rated Average Rated Average
d B A @ 10 F eet at d B A @ 10 F eet at
Current (AMPS) Current (AMPS)
Nominal Nominal
Tone Tone Description
24 V D C 12 V D C Input Voltage Input Voltage
HI dBA STD dBA HI dBA STD dBA HI STD HI STD
Horn Broadcast Horn
0.048 0.026 0.100 0.020 98 92 97 91
(Continuous)
Bell 1560 Hz Modulated
0.019 0.015 0.031 0.010 91 86 89 84
(0.07 Sec. ON/Repeat)
March Time Horn Horn (0.25 Sec. ON/0.25
0.048 0.026 0.100 0.020 98 91 97 91
Sec. OFF/Repeat)
Code-3 Horn Horn (ANSI S3.41
0.048 0.026 0.100 0.020 98 92 97 91
Temporal Pattern)
Code-3 Tone 500Hz (ANSI S3.41
0.028 0.015 0.060 0.015 94 89 93 88
Temporal Pattern)
Slow Whoop 500-1200Hz Sweep (4.0
Sec. ON/0.05 Sec. 0.045 0.026 0.100 0.025 98 93 97 92
OFF/Repeat)
Siren 600-1200Hz Sweep (1.0
0.039 0.020 0.082 0.020 97 92 96 91
Sec. ON/Repeat)
Hi/Lo 1000-800Hz (0.25 Sec.
0.023 0.017 0.044 0.013 92 87 91 86
ON/Alternate)
Vibrating Chime 700Hz (1.0 Sec
.014 0.011 0.027 0.010 88 82 87 81
Delay/Repeat)
02/04
Series 43T & Series MB
6” & 10” Bells
Description:
Wheelock’s bells offer low power consumption with high
sound. Various models are available to accommodate
different applications and voltage requirements.
Features:
• Approvals: UL Standard 464 Listed, Factory Mutual (FM),
California State Fire Marshal (CSFM), New York (MEA) and
Chicago (BFP)
• Weatherproof design (WBB backbox required - Order Code
2411)
• Aluminum bell housing
• Integral RFI suppression
Series 43T
• Screw terminal connections
Series 43T AC Vibrating Bells
• Solenoid driven
• Applications: Alarms, Doorbells, Gates
Series MB DC Vibrating Motor Bells
• Motor Driven
• Applications: Alarms, Doorbells, Gates

Order Shell Input Input dB A @ Mounting
Model Number Applications Agency Approvals
C ode Siz e Voltage Current 10 F eet Options#
AC Vibrating Bells (Solenoid Driven) UL MEA CSFM FM B FP
43T-G6-24-S 1626 6" 24 VAC .410 86 X X X X X
43T-G6-115-S 1630 Alarms 6" 115 VAC .085 86 X X X X X
Doorbells D,E,J,K,R,S,Z
43T-G10-24-S 3800 Gates 10" 24 VAC .410 88 X X X X X
43T-G10-115-S 3693 10" 115 VAC .085 88 X X X X X
DC Vibrating Bells
MB-G6-12-S 4221 6" 12 V D C .060 92 X X X X X
MB-G6-24-S 4222 Alarms 6" 24 V D C .030 92 X X X X X
Doorbells
MB-G10-12-S 4223 Gates 10" 12 V D C .060 92 D,E,J,K,R,S,Z X X X X X
MB-G10-24-S 4224 10" 24 V D C .030 92 X X X X X
MB-G6-6-R 4884 Elevators 6" 6 VD C .090 90 X X X X X
#See mounting options pull out guide in

X = Approved
* = Pending
02/04
Helping People Take ActionSM Series CVX/CSX
Explosion-Proof Bells
Description:
Wheelock’s Series CVX/CSX Explosion Proof Bells are rugged
and reliable for performance in hazardous environments.
These bells are Listed for Division One Applications — which
means that they are designed to operate safely in
atmospheres that actually contain explosive elements in free
form (in contrast with Division Two environments, wherein the
explosive elements are stored and protected).
Features:
• Approvals include: UL Standard, New York (MEA) and California State
Fire Marshal (CSFM)
• Rugged cast mechanism enclosure with hinged cover
• Available in single stroke and vibrating models Series CVXG10/CSXG10
• High sound output
• Outdoor models include protective hood and guard
Contents of Haz ardous
Specification and Ordering Information Class Group
Atmosphere
Vibrating Hydrogen or Gases &
Vapors of equivalent
Indoor Model Order Outdoor Order Shell Input Input dB A Mounting I B
hazard such as
Number Code Model Number Code Siz e Volt. Current @10 Ft. Options manufactured gas
CVX10-115-S 0132 CVXG10-115-S 0134 10" 115VAC 0.220 90 See Note 1 I C Ethyl & Ether Vapors
Single Stroke Gasoline, Petroleum,
Naphtha, Alcohol, Acetone,
Indoor Model Order Outdoor Order Shell Input Input dB A Mounting I D
Benzene, Lacquer Solvent,
Number Code Model Number Code Siz e Volt. Current @10 Ft. Options Vapors, Natural Gas
CSX10-115-S 0166 CSXG10-115-S 0167 10" 115VAC 0.125 87 See Note 1 Carbon Black, Coal, Coke
II F
Dust
CSX10-24-S 0164 CSXG10-24-S 0196 10" 24V D C 0.500 87 See Note 1
II G Flour, Starch, Grain Dusts
Notes: 1. All models include integral cast backbox for surface mounting with ½” threaded conduit entrances on top and bottom of housing.
Description:
Wheelock’s 31T-115-S Horn is a high performance horn. It is an
Series 31T-115S Horn
ideal alarm appliance for industrial signaling applications
where high sound output, low current draw, and dependable
operation are of critical concern.
The 31T-115-S offers rugged, vandal resistant construction with
die cast metal housings for the horn mechanism.
Features
• Approvals include: UL Standard, New York (MEA) and California State Fire Marshal (CSFM)
• Resonant grille design for high sound output with low current draw
• Fully factory assembled to save installation time
• Screw terminal inputs for fast and secure in-out field wiring
• Indoor or outdoor mounting options for semi-flush or surface mounting
• Attractive Grey textured finish enhances appearance
Series 31T-115-S
Model Number Order Code Input Voltage Rated Current d B A @ 10 F eet Mounting Options
31T-115-S 0521 115 VAC 0.160 95 D,E,J,K,O,R,Z
NOTES: 1. Typical dBA at 10 feet is measured in an anechoic chamber.

2. Refer to most current installation instructions.
02/04
Series Colored Lens
Helping People Take ActionSM Strobes (Amber, Blue,
Green and Red)
Description:
Wheelock’s colored lens strobe products are available on Series
RSS strobes and Series E speaker/strobes in amber, blue, green
or red lens colors. These products are not Listed for fire alarm
use, but they are built with the same high quality circuits and
parts used in Wheelock’s life safety strobes and speakers. They
are designed for indoor use and can be either wall or ceiling
mounted to standard electrical boxes or to Wheelock’s surface
mount boxes.
Features:
• Choice of four strobe lens colors with wide range of
intensity options Series RSS
• Wide operating voltage range
• Strobes can be synchronized with Wheelock’s SM or DSM Appliacations:
sync modules or POWER
POWERPATH™ power supplies Wheelock’s colored lens strobe products are
• Combination speaker/strobes available for voice messages designed for effective alerting of employees or
with visual alerting personnel in industrial, military or government
• Mount to standard electrical boxes applications. They are ideal for Mass Notification
• High quality designs from the leader in fire notification systems and for emergency, warning or trouble
alarms notification in many industrial operations.

MODEL NUMBER ORDER CODE LENS COLOR STROBE CANDELA MOUNTING OPTIONS STROBE VOLTAGE STROBE CURRENT (RMS) AGENCY APPROVALS
note 1 note 2 note 3 16 vdc 24 vdc
RSSA-24110W-NW 0103 AMBER 110 wall or ceiling 24 vdc 0.300 0.195 none
RSSB-24110W-NW 0100 BLUE 110 wall or ceiling 24 vdc 0.300 0.195 none
RSSG-24110W-NW 0099 GREEN 110 wall or ceiling 24 vdc 0.300 0.195 none
RSSA-24MCC-NW 0202 AMBER MCC wall or ceiling 24 vdc note 4 none
RSSB-24MCC-NW 0203 BLUE MCC wall or ceiling 24 vdc note 4 none
RSSG-24MCC-NW 0204 GREEN MCC wall or ceiling 24 vdc note 4 none
RSSR-24110C-NW 3111 RED 110 wall or ceiling 24 vdc 0.420 0.37 UL1638
RSSR-2475C-NW 3032 RED 75 wall or ceiling 24 vdc 0.315 0.200 UL1638
E70A-24110W-NW 0207 AMBER 110 wall or ceiling 24 vdc 0.300 0.195 none
E70B-24110W-NW 0208 BLUE 110 wall or ceiling 24 vdc 0.300 0.195 none
E70A-24MCC-NW 0209 AMBER MCC wall or ceiling 24 vdc note 4 none
E70B-24MCC-NW 0210 BLUE MCC wall or ceiling 24 vdc note 4 none
E90A-24110W-NW 0211 AMBER 110 ceiling 24 vdc 0.300 0.195 none
E90B-24110W-NW 0212 BLUE 110 ceiling 24 vdc 0.300 0.195 none
E90A-24MCC-NW 0213 AMBER MCC ceiling 24 vdc note 4 none
E90B-24MCC-NW 0214 BLUE MCC ceiling 24 vdc note 4 none
1. Candela is measured on axis per UL1638. Models w ith MCC strobes have 4 f ield-selectable candela
settings. MCC settings are rated f or clear lens - derate approximately 25% for amber, 55% f or green and
70% f or blue lenses.
2. Backboxes (ordered separately):
Se r ie s flus h s ur face
RSS 4" x 1-1/2", 1-gang or 2-gang box SHBB-W
E70 4" x 2-1/8" w ith extension ring SBB-W
E90 4" x 2-1/8" w ith extension ring na
3. A ll strobes operate from 16 to 33 volts at 1 f lash/second using filtered or f ull-w ave-rectif ied DC voltage.
(See Installation Instructions)
4. Strobe current f or MCC strobes:
M CC s e tting 15 30 75 95
current @ 16 vdc 0.065 0.105 0.189 0.249
current @ 24 vdc 0.045 0.070 0.119 0.159
08/04
Series UTA - Universal
Telephone Alerts
Description:
Wheelock Universal Indoor/Outdoor Telephone Alerts: UTA-1
and UTA-WH-VPS are loud attention getting electronic ringers
designed for use in noisy locations or for wide area coverage.
The UTA-1 operates off the telephone ringer voltage. The UTA-
WH-VPS requires 115 VAC and telephone ring trigger voltage
for activation of the strobe and ringer.
Features:
UT A-1 and UT
UTA-1 A-WH-VPS
UTA-WH-VPS
• Approvals Include: UL Standard 1950 approved
• ADA Compliant
Series UTA-WH-VPS
• Choice of four selectable sound patterns: Horn, Bell, Vibrating
Chime, Single Chime
• Choice of four operating voltages: 24VDC, 24VAC, 48VDC, 90Vrms/20-30Hz Series UTA-1
• High output 109 dB piezo speaker
• Low current draw and REN
Applications:
• Tamper resistant volume control
Offices of all types
• Dip switch selectable
Manufacturing Plants
• Equipped with a weather resistant backbox for optional outdoor use with
Machine shops
conduit-enclosed wiring
Factories
• Complies with: FCC part 68, CSA C22.2, IC C5-03
Construction sites
UT A-WH-VPS Universal TTelephone
UTA-WH-VPS elephone Alert with Strobe Shipping Yards
• Includes a high intensity 15 candela flashing strobe for visual signaling Processing Plants
• Equipped with a weather resistant backbox for optional outdoor use with Warehouses
conduit-enclosed wiring
• Requires 115 VAC power for strobe and piezo operation, and telephone
ring trigger voltage for activation - Line cord purchased separately

Model Number Order Code Description Pow er Requirements
UTA-1 6338 Universal Telephone Alert 24 VDC, 24 VAC, 48 VDC, 90 VRMS/20-30Hz

Requires 115 VAC power for strobe and piezo operation, and
Universal Telephone Alert
UTA-WH-VPS 6348 telephone ring trigger voltage for activation via 24VDC, 24VAC,
w/ Strobe
48VDC, 90VRMS/20-30Hz (Line cord purchased separately)
Tone Volume Range and Description

Volume Note: Not intended for wash down areas.
Horn 82-109 dB Broadband Horn
Bell 76-104 dB 1560 Hz Modulated (0.07 Sec. ON/Repeat)
Vibrating Chime 68-94 dB 700 Hz (1.0 Sec. Decay/Repeat)
Single Chime 68-94 dB 700 Hz (1.0 Sec. Decay)
dB @ 3 Feet (1 meter) Ring Voltage Current Draw mA R EN

Model
Tones 48 V D C 24 V D C 24 VAC 90 VRMS 20 Hz 48 V D C 24 V D C 24 VAC 90 VRMS 20 Hz
Number
Horn 107 108 105 104 26 30 46 1.6
Bell 100 100 102 100 10 9 39 1.4
UTA-1
Vibrating Chime 94 96 99 97 7 6 29 1.25
Single Chime 94 96 100 96 6 6 34 1.25
Horn 109 109 109 109 3 2.5 4 .6
Bell 104 104 104 104 3 2.5 4 .6
UTA-WH-VPS
Vibrating Chime 94 94 94 94 3 2.5 4 .6
Single Chime 94 94 94 94 3 2.5 4 .6
Voltage Range 36-60 20-30 20-30 40-130
02/04
Series PS Telestrobes
Description:
Wheelock Series PS Telestrobes emit a high intensity flashing
light when the telephone rings. Applications Include: Alerting
of the hearing impaired, for use in high ambient noise
environments, quiet hospital zones, libraries and broadcast
studios.
Features:
PS TTelestrobes
elestrobes
• Approvals Include: UL Standard 1459 Listed
• ADA compliant
• Designed for single line phones
• Convenient RJ-11C modular plug-in connection
• Long life, low power consumption xenon flash tube Series PS-15A-WPW
• Easily mounts to interior surfaces & PS-33A-WPW
• For indoor use
Series PS-11A-WPW
PS-11A-WPW
• Powered by 115 VAC
• Includes a 115 VAC power cord
• Bright 70,000 candlepower flash (15 candela)
• Designed for analog phone lines
PS-15A-WPW
• Powered by the telephone analog line ring voltage
PS-33A-WPW
• AC or DC powered
• Designed for low voltage connection
Model Number Order Code Description Input Voltage R EN Peak Candlepow er

PS-11A-WPW 3858 Single Analog Phone Line 40-130 V, 16-68 Hz, 115 VAC 3 70,000
PS-15A-WPW 3413 Single Analog Phone Line 50-130 V, 20-30 Hz 1.5 8,000
PS-33A-WPW 3209 Low Voltage 18-30 VAC or VDC N/A 25,000
08/04
Series CH Chimes &
Series WR Warble
Telephone Alerts
Description:
Wheelock modular telephone alerts are high quality,
compact signaling devices. Easily connects to phone
systems. Enables any moderately noisy environment such
as computer rooms, general office areas and lunchrooms to
have a loud telephone alert. Various models are available
to accommodate different voltage requirements.
Features:
• Connects with standard RJ-11C phone jack
• Tone and loudness are adjustable
• Helps solve the expensive problem of missed telephone calls
• Indoor use, surface mountable
• Analog, AC & DC models available Series CH-AT Chime
Series CH-BT
• CH-AT1-W and CH-BT1 are UL 1459 listed, FCC part 68 approved & WR-AT1-W Warble
Electronic TelChime
and DOC certified*
• WR-AT1-W is FCC part 68 approved and DOC certified
• Electronic Telchimes; CH-BT1, CH-BT2 and CH-BT4 have volume
and tone controls
• Electronic Chimes; CH-AT1-W and CH-AT2-W have volume and
tone controls

Model Order Signal Recommended Nominal Input Input Current or dB A @
R EN
Number C ode Type Coverage Area Current or Voltage Voltage Range 1 meter
CH-AT1-W 3198 Chime Up to 1000 sq. ft. 90 VRMS, 20-30 Hz 50-130 VRMS, 20-30 Hz 80 0.4
CH-AT2-W 3199 Chime Up to 1000 sq. ft. .02 Amps 18-30 VAC or VDC 80 N/A
WR-ATI-W 3862 Warble 1000-5000 sq. ft. 90 VRMS, 20-30 Hz 50-130 VRMS, 20-30 Hz 90 0.8
CH-BT1 3823 Chime 1000-5000 sq. ft. 90 VRMS, 20-30 Hz 40-130 VRMS, 20-30 Hz 90 0.4
CH-BT2 4077 Chime 1000-5000 sq. ft. .02 Amps 18-30 VAC or VDC 90 N/A
CH-BT4 4078 Chime 1000-5000 sq. ft. .01 Amps 38-60 VDC 90 N/A
CH-ATI-W, WR-ATI-W, and CH-BTI can be used on the Public Telephone Network or behind PBX with
interrupted ring voltages from 40-130 V, 20-30 Hz.
*Department of Communication fro Canadian Telephone.
02/04
Series CH Common
Description: Audible Control Units
Wheelock Series CA Common Audible Control Units monitor
multiple analog telephone lines (tip and ring) to provide all
call signaling, zoned signaling or night bell connection. These
control units also enable connection for operation of external
audible or visual alerts to be operated directly off the
telephone ring voltage output.
Features:
• Approvals Include: UL Listed
• Enables electronic key systems, PBX or 1A2 key systems to
have a dry contact closure to trigger other devices
• Choice of two outputs for alert signal connection: standard
ringing voltage or contact closure
• Easy connection to Wheelock’s dry contact interface (DCI-24-24) Series CA-312-1 & CA-622-1
or power supply (EPS-2401) for driving 24 volt alert signals
CA-312-1 3 CO Line, 1 Control Unit CA-622-1 6 CO Line, 2 Control Unit
• Monitors 3 tip and ring lines, 1 zone • Monitors 6 tip and ring lines, up to 2 zones
• Additional units can be cascaded to monitor
additional input lines
Model Order
Application Input Voltage Output R EN
Number C ode
CA-312-1 3780 Monitor up to 3 Tip & Ring Lines, 1 Zone 55-130V, 20-30 Hz Ringing Voltage or Dry Contact Closure 1
CA-622-1 3779 Monitor Up to 6 Tip & Ring Lines, 2 Zones 55-130V, 20-30 Hz Ringing Voltage or Dry Contact Closure 1
Series TB - Telbells
Features
• Aluminum bell housing
• Integral RFI suppression
• Screw terminal connections and RJ-11 plug
Series TB Modular Bells

• Approvals Include: TB-593 is UL Listed
• Motor Driven
• Tamper resistant volume control
• Applications: Telephone Ringers
• Weatherproof backbox for indoor/outdoor mounting included

Model Order Shell Input dB A @
Input Voltage
Number C ode Siz e Current 10 F eet
Series TB Modular
TB-591 4102 6" 38-60 VDC 0.025 100
Bells
TB-592 4101 6" 18-30 VAC/DC 0.025/.030 100
TB-593 4103 6" 55-130 V, 20-30 Hz N/A 95
TB-592 for phone systems with a programmed contact closure, EPS-2401 power supply required.
TB-593: REN: 1.6. For installation in Canada, a 7 ft. modular line cord w/CA-11 connector is required.
02/04
Telephone Relays
Description:
Wheelock telephone relays activate various appliances when
a telephone ring voltage is detected. Three models are
available to accommodate different voltage requirements,
environments and applications.
Features:
• Approvals Include: UL Listed, FCC registered
CRT -T
CRT-T -40
-T-40 Weatherproof AC/DC Relay
• Includes mounting bracket
• Hard wire connections
• Accepts RJ-11 phone plug
Series CRT-T-40
XRT -T
XRT-T -40
-T-40 Explosion-Proof AC/DC Relay
• Hard wire connections Series XRT-T-40
RX-1419 Telephone Relay
• Designed for analog phone lines or low voltage activations
• Screw terminal connections
• Includes AC line cord
• Replacement relay for 163 package Series RX-1419
Model Order Input AC Contact DC Contact

Application R EN
Number C ode Voltage Ratings Ratings
CRT-T-40 0049 Indoor/Outdoor 39-150 V, 20-30 Hz Up to 230 VAC Up to 115 VDC 0.6
XRT-T-40 0221 Explosion Proof 39-150 V, 20-30 Hz Up to 230 VAC Up to 115 VDC 0.6
39-150 V, 20-30 Hz 5A 115 VAC, 60 Hz -
RX-1419 0040 Indoor 18-48 VDC 2A 115 VAC, 60 Hz 0.6
30-48 VAC 0.5A 115 VDC -
02/04
Power Supplies
Power Supply Charger
Dry Contact Interface
EPS-1205 Economy Power Supply
• Approvals Include: UL listed
• 12 VDC, 500 mA, filtered, plugs into an AC outlet.
• Includes DC output cord with polarized plug.
• Economically powers AFT-100 AM/FM Tuner.
EPS-2401 Economy Power Supply
• Approvals Include: UL listed Series EPS-2401
• 24 VDC, 100 mA, filtered, plugs into an AC outlet.
• Powers 24 VDC alert signals and tone generators. Series EPS-1205
• B battery.
RPS-2406 Fully Regulated and Filtered
• 24 VDC, 600 mA, wall mounting with 6 ft. AC power cord. Series RPS-2406
• Current limited, short circuit and overload protected with auto
shutdown and reset.
• Power supply in non-UL fire alarm applications for Series DV-100
& DV-200 VoiceLink Systems.
• A battery.
RPS-2440-A 24 VDC Dual Output
• Either two 2 amp, or one 4 amp.
• Fully regulated and filtered.
• Each output with independent power on LED.
• Current limiting overload and short circuit protection.
• Auto shutdown and reset, AC circuit breaker for input protection.
• A battery.
Series RPS-2440-A
PSC-2420-R Power Supply/Charger
• 24 VDC, 1-8 fused outputs.
• 20.8 amp switch mode designed with full regulation and filtering.
• Outputs are current limited, overload and short circuit protected.
• Equipped with a battery charger capable of handling a 60 ampere hour battery load.
• PSC-2420-R, red cabinet; (21” H x 16” W x 6” D, 26 lbs. 6 oz.).
DCI-24-24 Dry Contact Interface
• Approvals Include: UL Standard 2017 Listed
• Provides the power to operate a wide variety of Wheelock 24 VDC signaling products
while isolating the load from the contact closure.
• Delivers 24 VDC at 300 mA via a dry contact closure.
• Can be wall-mounted, comes with six-foot power cord.
• Quick-connect input/output terminals require no special tools for hookup.
• Can power multiple Wheelock products.
• One DCI-24-24 can activate another DCI-24-24 to power additional products.
• Compatible Products: PS-33A, CH-AT2-W, CH-BT2, TB-592, UTA Series and MT-12/24-W
Series DCI-24-24

Model Order Output Output Regulation Ripple &
Description
Number C ode Voltage Current Noise
EPS-1205 4892 Filtered Power Supply 12 V D C 500mA Non-Regulated 2.5 VP-P
EPS-2401 3545 Filtered Power Supply 24 V D C 100mA Non-Regulated 10mVRMS
RPS-2406 3770 Regulated & Filtered Power Supply 24 V D C 600mA +/- 5% 10mVRMS
RPS-2440-A 4839 Dual Output Regulated & Filtered Power Supply 24 V D C 4 Amps +/- 5% 10mVRMS
PSC-2420-R 7377 Power Supply/Charger - Red cabinet (120 VAC) 24 V D C 20.8 Amps +/- 5% 2% max, p-p
PSC-2420E-R 7385 Power Supply/Charger (220 VAC) (E=Export) 24 V D C 20.8Amps +/- 5% 2% max, p-p
Input Output
DCI-24-24 24 VDC Dry Contact Interface
Dry Contact Closure 24 VDC (300 mA)
02/04
Series MZC Zone
Controller & Modules
Description:
Wheelock’s Series MZC-144 is a Modular Zone Control System
with 3 zones expandable to 12 zones.
Features:
• System can provide for one-way communication or
talk back
• DTMF tone access with 3 digit dialing
• All call and / or programmed zone paging
• Separate music sources can be inserted into each zone
group
• Field programmable for fixed or logical zones
• Music muting by zone Series
• Tone and paging volume control MZC-144
• Page alert tone
• Provides talk battery for unused CO line/trunk port and
stand-alone telephone applications
• Night ringer with contact closure activation
• Wall mountable
• Operates on 24 VDC, regulated and filtered power supply:
RPS-2440A, can power up to 72 zones
RPS-2406, can power up to 12 zones

Order
Model Number Product Description
C ode
MZC-144 7550 Programmable Modular Zone Control System, 3 Zones Expandable to 12 Zones.
Up to (12) MZC-144's can be stacked to accomodate up to a 144 Zone System
MZEM-3 7552 3 Zone Expansion Modules (Audio)
TBM 7551 Talk-Back Modules
MZC-RM 7555 Relay Module - Provides 3 Relay Contacts
MZC-CAB 7553 Expansion Cable - Interconnects Multiple MZC-144's
MZC-BOOSTER 7556 For use when more than 72 Zones are required - Includes Cable
Interface/Connection Options: Expandability/Optional Features:

• Universal interface: Can be connected directly to a • Each MZC-144 is expandable to 12 zones (MZEM-3)
telephone for stand alone paging, unused CO line/ with 4 music inputs
trunk port or 600 ohm audio page port • Up to 12 fully loaded MZC-144’s can be stacked to
• Compatible with PBX’s and EKSU’s accommodate a 144-zone system of one-way
• Wheelock SAFEPATH® Voice Evacuation systems for paging, talk back, or relay control.
OSHA related applications Note: When more then 72 zones are required, contact
Wheelock Technical support.
– A system booster and connection cable
(MZC-Booster) is required and will be supplied.
02/04
Series ST Paging
Speakers & Horns
Description:
Series ST Speakers & Horns provide clear, audible output for
voice paging, background music and tone alerting.
Features:
• Assortment of 4”, 8”, flush mount, ceiling mount,
weatherproof horns, self-amplified speakers and speakers
with volume controls
• ST-C8 and ST-C8V utilize a plastic grill
• ST-C8M and ST-C8MV utilize a metal grill
• ST-C8V and ST-C8MV have a recessed volume control
ST-C8
ST-C8V
ST-C8M
ST-B4
ST-C8MV
Model Order Transformer Taps dBA @ Frequency
Product Description Mounting
Number C ode in Watts 1 Meter Response
200 Hz
ST-B4 4116 4" Surface mount, 4 watt transformer, plastic housing, ivory 1/8, 1/4, 1/2, 1, 2, 4 93 Surface Mount
10 KHz
8" Surface mount, 6 watt, 5 oz with 4 watt transformer, round plastic 80 Hz
ST-C8 4114 1/8, 1/4, 1/2, 1, 2, 4 95 Flush Mount
grille, white 14 KHz
8" Surface mount, 6 watt, 5 oz with 4 watt transformer, round metal 80 Hz
ST-C8M 8474 1/8, 1/4, 1/2, 1, 2, 4 95 Flush Mount
grille, white 14 KHz
8" Surface mount, 6 watt, 5 oz with 4 watt transformer, recessed 80 Hz
ST-C8V 4871 1/8, 1/4, 1/2, 1, 2, 4 95 Flush Mount
volume control, round plastic grille, white 14 KHz
8" Surface mount, 6 watt, 5 oz with 4 watt transformer, recessed 80 Hz
ST-C8MV 8475 1/8, 1/4, 1/2, 1, 2, 4 95 Flush Mount
volume control, round metal grille, white 14 KHz
8" D x 10 1/2", weatherproof re-entrant horn, 15 watt transformer, 275 Hz
ST-H15-B 5147 See Chart Below 122 Universal fully adjustable base with banding
metal, beige 10 KHz
slots for beams or pillars. Conduit
10" D x 10 1/2", weatherproof re-entrant horn, 30 watt transformer, 275 Hz interface adapter with clear plastic shield.
ST-H30 5148 See Chart Below 125
metal, beige 10 KHz
Sound output measured at 1W @ 2KHz for ST-B4, ST-C8, ST-C8V, ST-C8MV. Full rated power for ST-H15-B and ST-H30
ST-H30 Wattage Selector ST-H15-B Wattage Selector

Switch Positions Switch Positions
1 2 3 4 5 6 7 1 2 3 4 5 6 7
70V 2.0 3.8 7.5 15.0 30.0 - - 70V 1.0 2.0 3.8 7.5 15.0 - -
25V 0.3 0.5 0.9 1.9 3.7 6.9 13.9 25V - - 0.48 0.94 1.9 7.5 15.0
100V 4.0 7.7 15.0 30.0 - - - 100V 2.0 3.8 7.5 15.0 - - -
ST-H30
08/04
Series SA Self Amplified
Paging Horns
SA-H5B, SA-H15B

Model Order Pow er Output @ 1000 dBA @ Frequency
Description Mounting
Number C ode Hz /Nominal Current 1 Meter R esp o n se
Universal, Fully Adjustable Mounting Base w/

8" Dia. X D Weatherproof
SA-H5B 5145 5 Watts/325 mA 118 275 Hz - 10 KHz Banding Slots for Beams or Pillars. Conduit
Re-entrant Horn, Metal, Beige
Interface Adapter w/ Clear Plastic Shield
8" Dia. X D Weatherproof Universal, Fully Adjustable Mounting Base w/

SA-H15B 5146 Re-entrant Horn, Metal, Beige 15 Watts/900 mA 122 275 Hz - 10 KHz Banding Slots for Beams or Pillars. Conduit
Interface Adapter w/ Clear Plastic Shield
SA Series speakers have barriered, clamp type screw terminals, impedance: 600 Ohms/operating voltage: 18-28 VDC
Sound output (dBA @ 1 meter) measured at rated power output at 100 Hz.
Series VC Wall Mount

Volume Controls
Description:
Wheelock’s VC-10 and VC-35 attenuators are ideal for
controlling the volume of a single speaker or a group of
speakers on a 25V or 70V line.
Features:
• Auto-transformer design for best efficiency
• Stainless steel wall plate
• Rotary switch that attenuates in 3dB steps to a completely
off position
Specification and Ordering Information VC-35

Model Order P o w er Frequency Insertion
Wall Plate
Number C ode Handling R esp o n se L o ss
VC-10 5159 10 Watts Better than 17 KHz Less than .5dB Single Gang
VC-35 5160 35 Watts Better than 17 KHz Less than .5dB Double Gang
02/04
Speaker Mounting
Accessories
SBB-8

CBB-8 Backbox
Model Order attached to SSB-8
Description Used With
Number C ode Tile Bridge
ST-C8, ST-C8V, ST-C8M, ST-C8VM,
CBB-8* 3314 UL Listed 8" Ceiling Speaker Backbox
S8-70/25, S8-24MCC, S8-24MCCH
ST-C8, ST-C8V, ST-C8M, ST-C8VM,
SSB-8 3573 8" Speaker Support Tile Bridge
S8-70/25, S8-24MCC, S8-24MCCH
SSB-4 3380 4" Speaker Support Tile Bridge Series E & ET
*Required for use with S8-70/25, S8-24MCC, & S8-24MCCH
PRM-150 Line Level

Pre-Amplifier
Features:
• Boosts the audio signal from 600 ohm CO and audio
page ports to a level capable of driving a maximum of
150 self-amplified speakers (Contact Technical Support
for wiring)
• Will compensate for audio signal loss on long cable run
• Can function as a one-way paging CO port interface
• Contains a volume control
• When used with Wheelock power supply (RPS-2406) talk
battery is supplied to the CO port
• Operating Voltage/Current: 24 VDC/25mA
• In/Out Impedance: 600 ohms/4 ohms
• Input level: -15dBM to + 10dB
• Max audio output level: 0.8 VRMS
PRM-150
Model Order
Description
Number C ode
PRM-150 3793 Line Level Pre-Amplifier Interface 1-Way Page to a CO Port
02/04
AFT-100 AM/FM Tuner

Features:
• 2 independent outputs with separate volume controls:
• line level for background music over a paging system
• 1/2 watt for music-on-hold for a telephone system
• Tone control for bass and treble
• Built in monitor speaker and telescoping/pivoting FM
antenna
• Analog tuning dial with automatic frequency control (AFC)
circuit
• Wall mountable, barriered screw terminals
• Includes external 300 ohm FM dipole antenna
• On/Off switch, tuning LED
• Can be powered by 12 or 24 VDC
• Recommended power supply: EPS-1205
Specification and Ordering Information AFT-100

Model Order
Description (Tuning Ranges)
Number C ode
AFT-100 4713 FM: 88-108 MHz AM: 540-1600 KHz
Microphone
Description:
Wheelock MIC-400 features durability, value and
performance, making it ideal for commercial PA applications.
Features:
• Smooth natural voice reproduction
• Extended frequency response
• Dynamic, low impedance
• Unidirectional pickup pattern
MIC-400
Model Order Cable & Frequency Sensitivity

Description Impedance
Number C ode Connector R esp o n se (+/- 3dB)
5' Male
MIC-400 5166 Hand held CB type Push-to-Talk (PTT) Switch 250-6 KHz -74 dB 3.8"H x 2.5"W x 1.5"D
Phone Plug
02/04
CCSWH
Central Control Station
Description:
The Central Control Station (CCSWH) is designed to meet
the requirements of military and industrial facilities for
reliable Outdoor and Indoor Emergency Notification. The
Central Control Station consists of a Central Control Unit
that interfaces with a computer PC station running
Wheelock Wireless Software.
The Wheelock Wireless Software Package displays
control and status activities, stores information and
displays system operations. Interfaced with the Central
Control Unit, the software processes and displays the FSK
data received and transmitted.
Features:
• Operates all Wheelock Outdoor and Indoor
Emergency Notification Equipment
• Configurable alarm activations. The alarm
configuration includes the alarm tone type, tone
duration, pre-recorded messages (optional) and
Standard Equipment:
number of cycles the alarm is to be played
• Archives and prints reports for all system activities The CCSWH includes Wheelock’s Central Control Unit,
• Automatic or manual operation reports Wheelock Wireless Software Package, Windows
• Supervises communication between the Central Operating System, computer, keyboard, monitor, printer,
Control Unit, Software and all remotely located mouse, cables, and multi-outlet strip.
equipment
• VHF or UHF or trunked radio operation
• CCSWH-PORTLT can be powered by a standard 120
VAC or 13.5 VDC vehicle source

Order
C ode
Central Control Station
Includes: (1) desk top receiver cabinet, system controller hardware & basic system
software, alarm screen touchpad/display, hand held (PTT) microphone, (1) 25 watt
CCSWH 9950 UHF or VHF radio, antenna polyphasor, power cord, 12 VDC/7AH battery, Pentium II
350 MHz computer, 17" color monitor, 32X CD ROM, Mouse, Windows 98 or NT, (1)
Dot Matrix Printer,
RS-232 Serial Port, Cables & Multi-outlet power strip.
CCSWHTS 9951 Same as above, but substitute a Touch Screen Monitor and Software
Mobile Central Control Station

Includes: (1) Panasonic Toughbook 48 laptop computer, system controller hardware
CCSWH-PORTLT 9952 & basic software, alarm screen touchpad/display, handheld (PTT) microphone, (1)
25 watt UHF or VHF radio, magnetic mount vehicle antenna. The CCSWH-PORT
central control station comes with a handle for easy transportation.
02/04
CCSWH-PORTLT
Portable Central Control
Description:
Station
The Portable Central Control Station (CCSWH-PORTLT)
is designed to meet the requirements of the military
and industrial facilities for reliable mobile command
for emergency notification.
Features:
• Panasonic Toughbook 48 Lap Top Computer
• Computer Complies with Mil Spec: 8-10S
• Operates on 120 VAC or 13.5 VDC
• System controller hardware & basic software
• Alarm screen touch pad/display
• Handheld (PTT) microphone
• 25 watt UHF or VHF radio
• Magnetic Mount Vehicle Antenna
• Includes Handle for Easy Transportation From
Vehicle to Vehicle

Order
C ode
Mobile Central Control Station
Includes: (1) Panasonic Toughbook 48 laptop computer, system controller hardware
CCSWH-PORTLT 9952 & basic software, alarm screen touchpad/display, handheld (PTT) microphone, (1)
25 watt UHF or VHF radio, magnetic mount vehicle antenna. The CCSWH-PORT
central control station comes with a handle for easy transportation.
02/04
Wheelock Wireless
Remote Controller (RCIWH)
Features:
The Remote Controller Interface Unit (RCIWH) is a fully supervised
wireless alarm monitoring station and two-way communications
controller installed at independent field-located SAFEPATH®
Evacuation System Panels. The RCIWH communicates with the
Wireless Central Control Station (CCSWH) via radio frequency
data transfer, using highly secure Frequency Shift Keying (FSK)
signaling technology. Each RCIWH is identified as an
independent addressable control point. Remote alarm
activation signals, low battery signals, and system trouble
conditions to the CCSWH(s) initiated by the SAFEPATH®
Evacuation System are transmitted via the RCIWH. The RCIWH’s
internal self-diagnostic “watch dog” circuitry also monitors
tamper, system power conditions and data communication
integrity.
The RCIWH interfaces with each independent SAFEPATH® to
“stream” selectable voice commands, digital messaging and
system control data directly from the CCSWH(s) over either
conventional licensed radio frequencies (UHF, VHF, 800MHz
and 900MHz ranges) or trunked RF communications systems. RCIWH
Superior internal surge suppression meets IEEE 587 and ANSI
C37.90 standards for both the mother board and the antenna
system. Each RCIWH is housed in a standard NEMA1 rated
painted steel enclosure, or in an optional NEMA4 or stainless
steel enclosure for severe weather resistance applications.
Features:
• Single Board Remote Controller Design
• Integral Radio for Communications with CCSWH
• Omni-Directional Antenna System
• 24VDC or 120V AC options
• Eight (8) Standard System Alarm Inputs
• One (1) Standard System Trouble Input
• Eight (8) Standard System Outputs
• Expandable Alarm Initiation Points

Model Order Weight
Description
Number C ode (lbs.)
Remote Controller Interface standard configuration
includes: (1) cabinet, (1) 25Watt UHF or VHF radio,
Antenna w/20' of Coaxial Cable. Antenna surge
RCIWH 9954 20
suppressor, (1) 12VDC, 7 AH Battery, (1) cabinet tamper
switch, (8) relay outputs, (8) inputs, a serial data port, (1)
FSK Communications Modem & (1) system trouble circuit.
RCI4WH 9955 Same as above but with a Weather Resistant Enclosure 50
RCI4XWH 9956 Same as RCIWH but with a Stainless Steel Enclosure 60
08/04
Series HPSS High Power
Speaker Stations
Description:
The Series HPSS High Power Speaker Stations provide reliable
directional alarm tone notification and emergency voice
instructions for industrial and facilities.
HPSS8WH 800 watt speaker system, two 400 watt speakers

HPSS12WH 1200 watt speaker system, three 400 watt speakers
HPSS16WH 1600 watt speaker system. four 400 watt speakers
HPSS24WH 2400 watt speaker system, six 400 watt speakers
HPSS32WH 3200 watt speaker system, eight 400 watt speakers
HPSS32WH
Speaker Assembly
S p e a k e r A s s e m b l y : Includes mounting bracket, 50 feet of
speaker and speaker pole mount kit.
C o n t r o l E n c l o s u r e : Includes NEMA4 stainless steel enclosure with
ventilated battery compartment and mounting hardware. Siren
control contains a microprocessor controller, conventional VHF or
UHF radio, antenna with 20' of coaxial cable, antenna surge
suppressor, local control push button alarms, tone generator,
automatic gain control for live P.A., intrusion sensor, Class-D
amplifiers, amplifier tray and battery charger. B attery compartment
contains battery power switch, intrusion sensor, ventilation louvers,
battery fuse and battery cables.
Features:
• Omni sound pattern of 121-127 dBC measured at 100 ft.
(Depending on model)
• Directional sound pattern can be configured for 90, 180,
270 or 360 degrees
• Speaker head direction provides intelligible sound due to
minimization of sound reflection HPSS32WH
• Automatic gain control for live voice Control & Battery
Cabinet
Model Order Weight
Description
Number C ode (lbs)
High Power Speaker Station equipped with (1) 800 Watt Speaker Head
Assembly, NEMA-4 stainless steel Control Cabinet & Cabinet Mounting Bracket.
The Control Cabinet contains: (1) wireless Controller, (1) UHF or VHF Radio,
Antenna with 20' of Coaxial Cable, Antenna Surge Suppressor, (1) Push Button
HPSS8WH 9960 for local Activation, tone generator, automatic gain control for live Microphone 70
operation, tamper switch, amplification tray, digital messaging module for up to 10
messages, battery charger, Battery Compartment which contains a battery power
switch, intrusion sensor, ventilation louvers, fuse set & cables. The unit operates
on either 120 or 240 VAC.
HPSS12WH 9962 Same as the HPSS8WH except the power is 1,200 Watts 250
DMRTWH 9973 Digital Message Recording Time per Message N/A
ENGWHxx 99xx Engineering charge (varies per institution)
BAT-250M 9959 12 VDC 50 AH Marine Battery
02/04
CUSTWH Wireless Emergency
Warning System Software &
Engineering Design
Description:
The windows-based Wireless Emergency Warning System
Software acts as an interactive operator control system. The
Graphical User Interface (GUI) and a system programming
tool can be installed at one or more host computer systems at
the Wireless Central Control Station(s) (CCSWH). The software
provides the user with several programmable tiers of operator
security and password protection, while identifying and
managing remote alarm points and trouble conditions via
wireless Remote Controller Interface Units (RCIWH) which
integrate with the SAFEPATH® Evacuation Systems. Using a
standard mouse or an optional touch screen interface, the
operator can perform various automatic test, verification and
control functions, including selectable system activation
(individually by RCIWH, by predefined groups of RCIWH’s, or
via system-wide All Call), selectable public addressing override
functions and custom digital messaging functions at the
Wireless Central Control Station(s). The software also provides
standard configurable performance parameters, system status
reporting, system trouble indications, pull down operator menus
and easy to understand help files for simplicity of operation.
Features:
• Comprehensive Acoustic Analysis and Modeling
• Customized software engineering
• Turn key integration and locally authorized services
• Trunking radios for communication with 800 MHz
and 900MHz systems
• Customized digitalized messaging
• Start-up assistance, training and documentation
• Lease-to-own purchasing options

Model Order
Description
Number C ode
System Softw are Customiz ation
The Engineering, Software Customization, System Start-up & Training Fees are
an initial charge which must be included as a separate line item on every
system. This fee covers initial system software engineering costs to customize
the user software to every sites's specific needs. Initial start-up costs include
the services of a qualified project engineer onsite with the installation entity to
CUSTWH 9978
assist in putting the system on line & one full day of user training on the system.
System documentation will include user manuals, a system software manual &
executable software disks. Note: Software changes not included in the initial
specification will be negotiated on a case-by-case basis. System start-up
assistance and 1 day of user training. Additional tim e for start-up assistance
or training will be negotiated on a case-by-case basis.
ENGWHxx 99xx Engineering Charge for remote controllers (varies per application)
Daukt Charge for additional Start-up, Training assistance or Field Non-Warranty
ASUTAWH 9988
Service. Actual expenses are additional.
HECWH 9989 Hourly Engineering Charge
02/04
Series EWR, EWP & EN4
Audible Strobe & Strobe
Appliance Enclosures
Description:
Wheelock’s Series EWR, EWP and EN4 Enclosures are designed
for use with Wheelock’s UL approved Audible Strobe and Strobe
Appliances.
Features:
• Vandal Resistant
• Easy installation and access for service
• Provides protection from incidental contact with equipment,
falling dirt, falling liquids, light splashes, rain, etc.
• UV stabilized against discoloration
Series EN4
Series EWR
Series EWR 8151 Slotted, Weather-Resistant Enclosure with Drain Screen
Series EWP 8150 Weather-Proof Enclosure with Drain Screen
Series EN4 8152 NEMA-4 Rated Enclosure
02/04
SERIES E70, ET70, CH70
Product
5.13" 5.24"
Dimensions
SERIES AS, ASWP

4 13/16 SQ
5.13"
2 1/2
SERIES ET90, E90, CH90

7/16 2 1/2
2 13/32
SERIES AHWP
4 1/8 SQ
3 3/8 SQ 3/4 1 1/2 MAX
4 25/64
SERIES ET1010
4 3/8 SQ
3 3/8 SQ 1 15/16 2 3/16
SERIES ET1080
5 7/16 SQ 3 7/16 2 1/4
3 3/8 SQ
SERIES RSSP
5 7/8
3 3/8 SQ
SERIES ET70WP
3 5/8
5 1/8 SQ
3 3/8 SQ
10 3/4
FIRE ALARM DEVICE - DO NOT PAINT
2 11/16
02/04
SERIES SM/DSM
4 31/32 SQ
Product
2 3/4
Dimensions
SERIES MIZ 2 3/4 1 3/8
4 1/4
4 1/2 3 9/32
5/16
SERIES 31T
FIRE ALARM DEVICE
DO NOT PAINT
3 3/8 SQ 1 5/16 1 3/8
SERIES CVX
2 3/ 16
7" MAX
TAPPED FOR 1/2" CONDUIT

(4) 15/16 MOUNTING HOLES
4 1/16 SQ
C
L
6 3/16
7 5/16 MAX
TAPPED FOR 1/2" CONDUIT
SERIES MB & 43T BELLS 10" SHELL
6 1/2
11 1/2 DIA MAX
SERIES AMT, MT
5 1/8 SQ
3 3/8 SQ 4 3/8
7" MAX
1 13/16 2 31/32
10" SHELL
6" SHELL
3 9/32
3 3/8 SQ 2 11/16 MAX
FIRE ALARM DEVICE - DO NOT

PAINT
SERIES RSS SERIES NS, NH

4 3/4 SQ 2 3/8
TOP
VERTICAL
STROB E
TOP
HORIZONTAL
STROB E
3 7/16 SQ
3 7/16 SQ
4 3/4 SQ
02/04
2 7/8
SERIES UTA
Product
Dimensions
4” SERIES CH-AT 2 1/2 1 3/4

5"
SQ
2.000"
4 3/4
SERIES UTA w/ Strobe
4 5/16
4” SQ
P P
H H SERIES CH-BT
5.000"
O 5" O 2 3/4 2 3/4
N N 1 1/2
E E
7 1/4
SERIES MAX
4 7/8
SERIES MT4
3 3/8 SQ
4.12" 2.07"
1/2 CONDUIT
4.12"
SERIES PS 2 1/2 3 1/8

SERIES DCI-24
2 1/2 1 3/4
2.000"
4 3/4 2.000"
4 3/4
02/04
Product
Dimensions
SERIES E50 SPEAKER
SERIES E50 SPEAKER STROBE
08/04
273 Branchport Avenue • Long Branch, NJ 07740 • (800) 631-2148 • www.wheelockinc.com 8-4A
Helping People Take ActionSM Replacement Covers
& Grilles
Description:
Replacement covers and grilles can be used to easily
change the color of appliances before or after
installation. Unique nickel plated grilles are available
for speakers and chimes.

Description Order Code Used On Color Lettering
ECHG70-N 3221 E70, ET70, CH70 Nickel Plate -
ECHG70-R 9058 E70, ET70, CH70 Red -
ECHG70-W 9059 E70, ET70, CH70 White -
ECHSG70-FN 3224 E70, ET70, CH70 w/Strobe Nickel Plate FIRE
ECHSG70W-FR 9060 E70, ET70, CH70 w/Strobe Red FIRE
ECHSG70W-FW 9061 E70, ET70, CH70 w/Strobe White FIRE
ECHG90-N 3222 E90, ET90, CH90 Nickel Plate -
ECHG90-R 9062 E90, ET90, CH90 Red -
ECHG90-W 9063 E90, ET90, CH90 White -
ECHSG90-N 3223 E90, ET90, CH90 w/Strobe Nickel Plate -
ECHSG90-R 9064 E90, ET90, CH90 w/Strobe Red -
ECHSG90-W 9065 E90, ET90, CH90 w/Strobe White -
NSP-R 9054 NS Red -
NSPW-FR 9055 NS Red FIRE
NSP-W 9056 NS White -
NSPW-FW 9057 NS White FIRE
RSSCP-R 9050 RSS Red -
RSSCPW-FR 9051 RSS Red FIRE
RSSCP-W 9052 RSS White -
RSSCPW-FW 9053 RSS White FIRE
02/04
Agency Approvals
Agency Approvals
Model UL MEA CSFM FM BFP

31T-115R X X X X X
Agency Approvals Agency Approvals
31T-115-R-ULC/CSA X X X X X
43T-G6-24-R X X X X X Model UL MEA CSFM FM BFP Model UL MEA CSFM FM BFP
43T-G6-115-R X X X X X E90-24MCC-FW X X X * * MT4-115-R X X X X X
43T-G10-24-R X X X X X E90-24MCCH-FN X X X * * MT4-115-WH-VFR X X X X X
43T-G10-115-R X X X X X E90-24MCCH-FW X X X * * MTWP-2475W-FR X X X X *
AH-12-R X X X X X E90-N X X X X X NH-12/24-R X X X X X
AH-12WP-R X X X X E90-W X X X X X NS-121575W-FR X X X X X
AH-24-R X X X X X NS-241575W-FR X X X X X
ET-1010-R X X X X
AH-24WP-R X X X X NS-24MCW-FR X X X X X
ET-1010-W X X X X
AMT-12/24-R X X X X X NS-24MCW-FW X X X X X
ET-1080-R X X X X PS-12/24-8CP X * X * *
AMT-12/24-R-NYC X X X X X
ET70-241575W-FN X X X * X PS-12/24-8MP X X X X X
AMT-241575W-FR X X X X *
ET70-241575W-FR X X X * X RSS-121575W-FR X X X X X
AMT-241575W-FW X X X X *
ET70-24MCW-FN X X X * X RSS-241575W-FR X X X X X
AMT-241575W-FR-NYC X X X X *
ET70-24MCW-FR X X X * X RSS-24MCC-FW X X X X *
AMT-24MCW-FR X * X * *
ET70-24MCW-FW X X X * X RSS-24MCCH-FW X X X * *
AMT-24MCW-FW X * X * *
ET70WP-2475W-FR X X X * * RSS-24MCCHR-FW X X X * *
AS-241575W-FR X X X X X RSS-24MCCR-FW X X X * *
AS-121575W-FR X X X ET70-24MCWH-FN X X X * *
RSS-24MCW-FR X X X X X
AS-24MCC-FR X X X * * ET70-24MCWH-FR X X X * *
RSS-24MCWH-FR X X X * *
AS-24MCC-FW X X X * * ET70-24MCWH-FW X X X * *
RSSP-121575W-FR X X X X X
AS-24MCCH-FW X X X * * ET70-N X X X * X RSSP-241585W-FR X X X X X
AS-24MCW-FR X X X X X ET70-R X X X * X RSSP-24MCW-FR X X X X X
AS-24MCW-FW X X X X X ET80-241575W-FR X * X * * RSSP-24MCWH-FR X X X * *
AS-24MCWH-FR X X X * * ET80-241575W-FW X * X * * RSSWP-2475W-FR X X X X *
AS-24MCWH-FW X X X * * ET80-24MCW-FR X * X * * SM-12/24-R X X X X X
ASWP-2475W-FR X X X X X ET80-24MCW-FW X * X * *
CH70-241575-FR X X X X ET80-24MCWH-FR X * X * *
CH70-24MCW-FR X X X X ET80-24MCWH-FW X * X * *
CH70-24MCW-FW X X X X ET90-24MCC-FN X X X * *
CH70-24MCWH-FR X X X * ET90-24MCC-FW X X X * *
CH70-24MCWH-FW X X X * ET90-24MCCH-FN X X X * *
CH70-24-R X X X X ET90-24MCCH-FW X X X * *
CH90-24MCC-FW X X X * ET90-N X X X * X
CH90-24MCCH-FW X X X * ET90-W X X X * X
CH90-24-W X X X X HS-24-R X X X X *
CSX10-115-R X X X X HS-24-W X X X X *
CSX10-24-R X X X X HS4-241575W-FR X X X X *
CVX10-115-R X X X X HS4-241575W-FW X X X X *
E50-R X * * * * HS4-24MCW-FR X X X X *
E50-W X * * * * HS4-24MCW-FW X X X X *
E50-241575W-FR X * * * * HS4-24MCWH-FR X X X * *
E50-241575W-FW X * * * * HS4-24MCWH-FW X X X * *
E50-24MCW-FR X * * * * MB-G6-12-R X X X X X
E50-24MCW-FW X * * * * MB-G6-24-R X X X X X
E50-24MCWH-FR X * * * * MB-G10-12-R X X X X X
E50-24MCWH-FW X * * * * MB-G10-24-R X X X X X
E70-241575W-FR X X X * X MIZ-24S-R X X X X *
E70-241575W-FN X X X * X MIZ-24S-W X X X X *
E70-24MCW-FN X X X * X
X = Agency Approved
MT-12/24 X X X X X
E70-24MCW-FR X X X * X * = Pending
MT-121575W-FR X X X X *
E70-24MCW-FW X X X * X MT-241575W-FR X X X X *
E70-24MCWH-FN X X X * * MT-24MCW-FR X * X * *
E70-24MCWH-FR X X X * * MT-24MCW-FW X * X * *
E70-24MCWH-FW X X X * * MT4-115-R X X X X X
E70-N X X X * X MT4-115-WH-VFR X X X X X
E70-R X X X * X MTWP-2475W-FR X X X X *
E90-24MCC-FN X X X * *
10/04
GENERAL AND TECHNICAL NOTES
Warnings General & Technical
NOTE: ALL CAUTIONS AND WARNINGS are identified by the symbol
All warnings are printed in bold capital letters. Notes
Specification Notes
WARNING: THESE APPLIANCES WERE TESTED TO THE LISTED OPERATING VOLTAGE LIMITS USING FILTERED (DC) OR UNFILTERED (DC) OR
FULL-WAVE-RECTIFIED (FWR). DO NOT APPLY 80% AND 110% OF THESE VOLTAGE VALUES FOR SYSTEMS OPERATION. THE APPLICATION OF
IMPROPER VOLTAGE MAY RESULT IN DEGRADED OPERATION OR DAMAGE TO THESE PRODUCTS.
WARNING: MAKE SURE THAT ALL FUSES USED ON NAC CIRCUITS ARE RATED TO HANDLE THE MAXIMUM INRUSH OR PEAK CURRENT FOR
ALL APPLIANCES ON THOSE CIRCUITS. FAILURE TO DO THIS MAY RESULT IN LOSS OF POWER TO THE NAC CIRCUIT AND THE FAILURE OF
ALL APPLIANCES ON THAT CIRCUIT TO OPERATE, WHICH COULD RESULT IN PROPERTY DAMAGE AND SERIOUS INJURY OR DEATH TO YOU
AND/OR OTHERS.
The UL Listed “Regulated Voltage Range” is 16-33 VDC or 8-17.5 VDC using either filtered (DC) or unfiltered full-wave rectified (FWR) voltage unless
otherwise noted in this catalog. Check the minimum and maximum output of the power supply and standby battery and subtract the voltage drop from
the circuit wiring resistance to determine the applied voltage to the strobes.
All candela ratings represent minimum effective strobe intensity based on UL 1971.
WARNING: USE STROBES ONLY ON CIRCUITS WITH CONTINUOUSLY APPLIED OPERATING VOLTAGE. DO NOT USE STROBES ON CODED OR
INTERRUPTED CIRCUITS IN WHICH THE APPLIED VOLTAGE IS CYCLED ON AND OFF, AS THE STROBE MAY NOT FLASH.
Wheelock products must be used within their published specifications and must be PROPERLY specified, applied, installed, operated, maintained and
operationally tested in accordance with their installation instructions at the time of installation and at least twice a year or more often and in accordance
with local, state and federal codes, regulations and laws. Specification, application, installation, operation, maintenance, and testing must be performed
by qualified personnel for proper operation in accordance with all of the latest National Fire Protection Association (NFPA), Underwriters’ Laboratories
(UL), National Electrical Code (NEC), Occupation Safety and Health Administration (OSHA), local, state, county, province, district, federal and other
applicable building and fire standards, guidelines, regulations, laws, and codes including, but not limited to, all appendices and amendments and the
requirements of the local authority having jurisdiction (AHJ).
1. All VFWR voltages in strobe current requirement table are measured with DC volt meter. Multiply VFWR voltage by 1.11 to convert to VRMS.
2 Use the highest value of rated average current to determine the maximum number of strobes and to establish power supplies and wire gauge
requirements. Use the rated peak current or rated inrush current (whichever is higher) to verify fuse requirements.
3. Make sure that the average, peak and inrush currents do not exceed system power supplies or fusing limits. See “Installation Instructions”.
4 The 15/75 cd wall mounted strobes are listed at 15 cd under UL Standard 1971 and meet 75 cd intensity on axis for ADA Guidelines.
5. Read Installation Instructions for the Software Installation and operation of Electronic Access Control Products.
WARNING: CONTACT WHEELOCK FOR THE MOST CURRENT “SPECIFICATION SHEETS”, “INSTALLATION INSTRUCTIONS” AND “GENERAL
INFORMATION” SHEETS ON THESE PRODUCTS. THESE DOCUMENTS UNDERGO PERIODIC CHANGES. IT IS IMPORTANT THAT YOU HAVE
CURRENT INFORMATION ON THESE PRODUCTS. THESE MATERIALS CONTAIN IMPORTANT INFORMATION THAT SHOULD BE READ PRIOR TO
SPECIFYING OR INSTALLING THESE PRODUCTS INCLUDING:
• TOTAL CURRENT REQUIRED BY ALL APPLIANCES CONNECTED TO SYSTEM PRIMARY AND SECONDARY POWER SOURCES.
• FUSE RATINGS ON NAC CIRCUITS TO HANDLE MAXIMUM INRUSH OR PEAK CURRENT FROM ALL APPLIANCES ON
THOSE CIRCUITS.
• COMPOSITE FLASH RATE FROM MULTIPLE STROBES WITHIN A PERSON’S FIELD OF VIEW.
• INSTALLATION OF 110 CANDELA STROBE PRODUCTS IN SLEEPING AREAS.
• INSTALLATION IN OFFICE AREAS AND OTHER SPECIFICATION AND INSTALLATION ISSUES.
• LIMITED WARRANTY CONDITIONS.
WARNING: FAILURE TO COMPLY WITH ANY INSTRUCTIONS, CAUTIONS, AND WARNINGS COULD RESULT IN IMPROPER APPLICATION,
INSTALLATION AND/OR OPERATION OF THESE PRODUCTS IN AN EMERGENCY SITUATION, WHICH COULD RESULT IN PROPERTY DAMAGE,
SERIOUS INJURY OR DEATH TO YOU AND/OR OTHERS.
Mounting Notes
Caution: The mounting option figures show the maximum number of field wires (conductors) that can enter the backbox used with each
mounting option. If these limits are exceeded, there may be insufficient space in the backbox to accommodate the field wires and stresses from the
wires could damage the product.
Although the limits shown for each mounting option comply with the NFPA 70, National Electrical Code (NEC), Wheelock recom-
mends use of the largest backbox option and the use of approved stranded field wires, whenever possible, to provide additional
wiring room for easy installation and minimum stress on the product from wiring.
Caution: Check that the installed product will have sufficient clearance and wiring room prior to installing backboxes and conduit, especially if
sheathed multiconductor cable or ¾” conduit fittings are used.
1. Mounting hardware for each mounting option is supplied.
2. Conduit entrances to the backbox should be selected to provide sufficient wiring clearance for the installed product. When extension rings are
required, conduit should enter through the backbox, not the extension ring. Use Steel City #53151 (1-½” deep) or #53171 (2-1/8” deep) extension
rings (as noted in the mounting options) or equal with the same cut-out area.
3. When terminating field wires, do not use more lead length than required. Excess lead length could result in insufficient wiring space for the
notification appliance.
4. Use care and proper techniques to position the field wires in the backbox so that they use minimum space and produce minimum stress on the
product. This is especially important for stiff, heavy gauge wires and wires with thick insulation or sheathing.
5. Do not pass additional wires (used for other than the notification appliance) through the backbox. Such additional wires could result insufficient
wiring space for the notification appliance.
ANY MATERIAL EXTRAPOLATED FROM THIS DOCUMENT OR FROM WHEELOCK MANUALS OR OTHER DOCUMENTS DESCRIBING THE
PRODUCT FOR USE IN PROMOTIONAL OR ADVERTISING CLAIMS, OR FOR ANY OTHER USE, INCLUDING DESCRIPTION OF THE PRODUCT’S
APPLICATION, OPERATION, INSTALLATION AND TESTING IS USED AT THE SOLE RISK OF THE USER AND WHEELOCK WILL NOT HAVE ANY
LIABILITY FOR SUCH USE.
Due to continuous development of our products, specifications and offerings are subject to change without notice in accordance with Wheelock, Inc.
standard terms and conditions.
08/04
Installation Instructions
SM
Helping People Take Action & Specification Sheets
Reference Page
Installation Spec.
Products Description Instruction Sheet Sheet CSFMs
Fire Notification Products
Series AMT-12/24 Multitone - 3 inputs P82623 S4000 CSFM
Series AMT-241575, AMT-24MCW Multitone Strobe - 1575cd or 15,30,75,110 cd, wall P84158 S4000 CSFM
Series AMT-241575 Multitone Strobe (NYC) - 1575 cd, wall P84157 S4100
Series AS-121575, AS-241575 Audible Strobe - 1575 cd, wall P84240 S8100 CSFM
Series AS-24MCW Audible Strobe - 15,30,75,110 cd, wall P83947 S8100 CSFM
Series AS-24MCC Audible Strobe - 15,30,75,95 cd, ceiling P84395 S8100 CSFM
Series AS-24MCWH Audible Strobe - 135,185 cd, wall P84449 S8100 CSFM
Series AS-24MCCH Audible Strobe - 115,177 cd, ceiling P84448 S8100 CSFM
Series AH-12, AH-24 Audible P83519 S8100 CSFM
Series ASWP Audible Strobe - 180 cd, weatherproof P83957 S9004 CSFM
Series AHWP Audible - outdoor P83641 S9004 CSFM
Series CVX, CSX Bell - explosion-proof, 10-inch, indoor or outdoor P81612 S0200 CSFM
Series CH70, CH90 Chime P83720 S0710 CSFM
Series CH70-241575 Chime - 1575 cd, wall P83599 S0710 CSFM
Series CH70-24MCW Chime - 15,30,75,110 cd, wall P83932 S0710 CSFM
Series CH90-24MCC Chime - 15,30,75,95 cd, ceiling P84399 S0710 CSFM
Series CH70-MCWH Chime - 135,185 cd, wall P84467 S0710 CSFM
Series CH90-MCCH Chime - 115,177 cd, ceiling P84468 S0710 CSFM
Series DSM Sync module - dual circuit P83177 S3000 CSFM
Series E70A, E70B, E90A, E90B Speaker Strobe - amber or blue lens P84566 S9020
Series E70, E90 Speaker - wall or ceiling P83566 S1610 CSFM
Series E70-241575 Speaker Strobe - 1575 cd, wall P83566 S1610 CSFM
Series E70-24MCW Speaker Strobe - 15,30,75,110 cd, wall P83934 S1610 CSFM
Series E90-24MCC Speaker Strobe - 15,30,75,95 cd, ceiling P84398 S1610 CSFM
Series E70-24MCWH Speaker Strobe - 135,185 cd, wall P84451 S1610 CSFM
Series E90-24MCCH Speaker Strobe - 115,177 cd, ceiling P84452 S1610 CSFM
Series ET70, ET90 Speaker - wall or ceiling P83567 S0310 CSFM
Series ET70-241575 Speaker Strobe - 1575 cd, wall P83567 S0310 CSFM
Series ET70-24MCW Speaker Strobe - 15,30,75,110 cd, wall P83933 S0310 CSFM
Series ET90-24MCC Speaker Strobe - 15,30,75,95 cd, ceiling P84396 S0310 CSFM
Series ET70-24MCWH Speaker Strobe - 135,185 cd, wall P84453 S0310 CSFM
Series ET90-24MCCH Speaker Strobe - 115,177 cd, ceiling P84454 S0310 CSFM
Series ET-1080 Speaker - vandal resist, wall P83575 na S0800 CSFM
Series ET80-24MCW Speaker Strobe - vandal resist, 15,30,75,110 cd, wall P82506 S0800 CSFM
Series ET80-24MCWH Speaker Strobe - vandal resist, 135,185 cd, wall P84507 S0800 CSFM
Series ET70WP Speaker Strobe - weatherproof P84149 S9006 CSFM
Series EWR Enclosure - for audibel strobes, speaker strobes P83880 S9002
Series EWP Enclosure - for strobes P83879 S9002
Series EN4 Enclosure - NEMA 4 for strobes P83937 S9002
Series HS Audible P84432 S2400 CSFM
Series HS4-241575 Audible Strobe - 1575 cd, wall P84403 S2400 CSFM
Series HS4-24MCW Audible Strobe - 15,30,75,110 cd, wall P84391 S2400 CSFM
Series HS4-24MCWH Audible Strobe - 135,185 cd, wall P84469 S2400 CSFM
Series MB Bell - 6 or 10-inch, 12 or 24 vdc P81960 S1500 CSFM
Series MIZ-24S Mini Horn - continuous, code-3, sync P84408 S1700 CSFM
Series MPS-100 Pull Station - single action MPS-100 S5008 CSFM
Series MPS-200 Pull Station - double action MPS-200 S5008 CSFM
Series MPS-400X Pull Station - explosion-proof, single action MPS-400X S5008 CSFM
08/04
SM
Reference Page
Series MT Multitone P82467 S2000 CSFM

Series MT-121575, MT-241575, MT-
24MCW Multitone Strobe - 1575 cd or 15,30,75,110 cd, wall P84155 S2000 CSFM
Series MT4-115 Multitione - 115 vac P83159 S2000 CSFM
Series MT4-115-WH Multitione Strobe - 115 vac P83160 S2000 CSFM
Series MTWP Multitone Strobe - weatherproof P84150 S9004 CSFM
Series NH Audible P83600 S2100 CSFM
Series NS-24MCW Audible Strobe - 15,30,75,110 cd, wall P83983 S2100 CSFM
Series NS-121575, NS-241575 Audible Strobe - 1575 cd, wall P84234 S2100 CSFM
Series PS-12/24-8CP Power Supply - NAC, 8-amps, 200 ma aux P84515 S9000 CSFM
Series PS-12/24-8MP Power Supply - NAC, 8-amps, 3.5 amp aux P84333 S9000 CSFM
Series RSS-241575, RSSP-241575 Strobe - 1575 cd, wall P84233 S0410 CSFM
Series RSS-24MCW, RSSP-24MCW Strobe - 15,30,75,110 cd, wall P83911 S0410 CSFM
Series RSS-24MCC, RSS-24MCCR Strobe - 15,30,75,95 cd, ceiling, round or square P84394 S0410 CSFM
Series RSS-24MCWH, RSSP-24MCWH Strobe - 135,185 cd, wall P84450 S0410 CSFM
Series RSS-24MCCH, RSS-24MCCHR Strobe - 115,177 cd, ceiling, round or square P84442 S0410 CSFM
Series RSSA, RSSB, RSSG Strobe - amber or blue or green lens P84517 S9020
Series RSSWP Strobe - outdoor P84135 S9004 CSFM
Series RSSR Strobe - red lens P83884 S9008
Series S8, S8-24MCC, S8-24MCCH Speaker or Speaker Strobe - 8-inch, ceiling P84478 S1100 CSFM
Series SA-S70, SA-S90 Speaker - amplified, wall or ceiling P84502 S1800
Series SA-S90-24MCC Speaker Strobe - amplified, 15,30,75,95 cd, ceiling P84503 S1800
Series SA-S90-24MCW Speaker Strobe - amplified, 15,30,75,115 cd, wall P84501 S1800
Series SM Sync module - single circuit P83123 S3000 CSFM
Series STH-15S Speaker - compression horn, 15 w P82697 S0100 CSFM
Series 43T Bell - 6 or 10-inch, 24 or 115 vac P10352 S0600 CSFM
Series 31T Horn - 115 vac P10010 S0500 CSFM
Mounting Accessories and Heights Accessory Drawings, Matrix, Mounting Heights S7000
Product Dimensions Product Drawings
Spec.
Facility Communications Inst Inst Sheet Sheet CSFMs
Facility Communications Systems

Series DCSP-4RP, DCSP-8RP,
DCSP15SP Dual Circuit SAFEP ATH™ P83569 V2000 CSFM
Series SAPE-1AR, SAPE-2AR Multi-Circuit SAFE PATH™ P83331 V2000 CSFM
Series RSAPE-1AR Remote Multi-Circuit SAFE PATH™ P83665 V2000 CSFM
Series RMS-1R Remote Microphone (Multi-Circuit) P83450 V2000
Series RMS-3R Remote Microphone (Dual Circuit) P83542 V2000
Series SD-RMS-1RMB Remote Microphone (Four Circuit) P83819 V2000
Series AIM-3 Auxiliary Input Module P83667 Catalog
Series NACIM Notification Appliance Circuit Interface Module P83487 V2000
4-Zone Class B Speaker Splitter

Series SPL Speaker Splitter - Dual Circuit SAFEP ATH™ P83541 V2000
Series SPL Speaker Splitter - Multi Circuit SAFEP ATH™ P83541 V2000
Series SP40/2 Audio System - SAFEPATH 4 ™ P84116 V2003 CSFM
Series SPB-160 160-Watt Supervised Audio Power Booster P84296 V2010 CSFM
Series SPB-80/4 80-Watt Supervised Audio Power Booster P84296 V2010
08/04
SM
& Specification Sheets
Reference Page
Series SP4Z-A/B Audio splitter - 4-Zone Class B or 2-Zone Class A P84205 V2010 CSFM
Series SPRM Remote Microphone P84207 V2010 CSFM
Series SP4-3MEM-SMK, SP4-3MEM-PMK 3 Message Expander Module P84482 V2010
SAFEPATH™ Programmed Message Kit Order Form

SAFEPATH 4 SP40/SPB Battery Calcs Excel Spreadsheet
Personnel Alerting
Series PAS Personnel Alert System Catalog
Series RAAS Restricted Area Alert System Catalog
Series DRAAS Deployable Restricted Area Alert System S9010
Series NPS Push Stations P84249 V2004
Series SD-RMS-1RMB Rack Mount Remote Microphone Station P83819 V2006
Wireless
Series CCSWH Central Control Station WW8000
Series CCSWH-PORTLT Portable Central Control Station WW8000P
Series CCUWH Central Control Unit WW8001
Series RCIWH Wheelock Wireless Remote Controller WW8002
Series HPSS, MPSS Speaker Stations - High & Medium power WW8003
Series CUSTWH System Software - Wireless Emergency Warning WW8804
Spec.
Commercial Audio/Voice Systems Inst Inst Sheet Sheet CSFMs
VOICELINK Multi-Message Systems
Series DV-100 Voicelink - 4 Channel Playback System P82339 V1000 CSFM
Series DV-200 Voicelink - 4 Channel Record/Playback System P82632 V1000 CSFM
Series MDV-2 Voicelink - 2 Channel Playback system P83452 V1000 CSFM
Series DV-EM Voicelink - Expansion Module P82356 V1000
VOICELINK Programmed Message Kit Order Form
Zone Controller and Modules
Series MZC-144 Programmable Modular Zone Control System P83259 T3600
Series MZC-RM MZC Relay Module P83477 T3600
Series MZEM-3 Three Zone Expansion Module For Audio P83272 T3600
Series TBM Talk-Back Module P83271 T3600
Series MZC MZC Booster P84034 T3600
Input/Output Equipment
Series AFT-100 AM/FM Tuner P82214 Catalog
Series PRM-150 Line Level Pre-Amplifier P81537 Catalog
Series SA-H5 Self-Amplified Paging Horn - 5 watts P82580 Catalog
Series SA-H15 Self-Amplified Paging Horn - 15 watts P82580 Catalog
Series ST-C8, ST-B4 Paging Speakers - flush or surface, 25/70 vrms P81832 Catalog
Series ST-H15, ST-H30 Paging Horn Speaker P82595 Catalog
Series STH-15S Supervised Horn Loudspeaker P82697 S0100 CSFM
Series STH w/opt strobe Cluster Speakers - with optional DC-MAX strobe P83699 S9003
Series STH -4M30WC Cluster Speaker - with strobe, weatherproof P84196 S9005
Series STH-MCCH Cluster Speakers - with 115/177 cd strobe P84327 S9009
Accessories
Series PSC-2420 Power Supply - 24 vdc, 20.8A, 8 outputs P83572 Catalog CSFM
Series RPS-2406 Power Supply - 24 vdc, 600 ma P81634 Catalog
Series SSB-4 Speaker Support Bridge - 4" speakers P82288 Catalog
Series SSB-8 Speaker Support Bridge - 8" speakers P81490 Catalog
Spec.
Telephone Products Inst Inst Sheet Sheet
Series CA-312-1 Common Audible Control Units - 3 CO Line P81535 Catalog
Series CA-622-1 Common Audible Control Units - 6 CO Line P81534 Catalog
Series CH-AT1-W Electronic Chim e - Ring Voltage P81087 Catalog
Series CH-AT2/CH-BT2/CH-BT4 Electronic Chim es - Indoor, AC or DC P81132 Catalog
Series CH-BT1 Electronic Chim e - Ring Voltage P81610 Catalog
10/04
SM
Reference Page
Series CRT-T-40 / XRT-T-40 Telephone Relays - Weatherproof or Explosion-proof P81030 Catalog

Series RX-1419 Telephone Relay - Indoor P81363 Catalog
Series DCI-24-24 Power Supply - Dry Contact Interface P81234 Catalog
Series MTH-24 Multi-Tone Horn - Hi dBA, with Power Supply P81543 Catalog
Series PS-11A-WPW TelStrobe - Indoor, 115VAC P80945 Catalog
SeriesPS-15A-WPW Telstrobe - Indoor, Ring Voltage P81280 Catalog
Series PS-33A-WPW TelStrobe - Indoor, AC or DC P81186 Catalog
Series TB-591/592 Modular TelBell - AC or DC P81897 Catalog
Series TB-593 Modular TelBell - Ring Voltage P81898 Catalog
Series UTA-1 Universal Telephone Alert P82968 Catalog
Series UTA-WH-VPS Universal Telephone Alert with Strobe P82969 Catalog
Spec.
Industrial Products Inst Inst Sheet Sheet
Series 31T-115 Horn - 115 vac P10010 Catalog
Series 43T Bell - 6 or 10-inch, 24 or 115 vac P10352 Catalog
Series AMT Multitone - 12/24 vdc, 3 inputs P82623 Catalog
Series AMT w/strobe Multitone Strobe - 24 vdc, 1575 cd, wall P84158 Catalog
Series CVX/CSX Bell - explosion-proof, 10-inch, indoor or outdoor P81612 Catalog
Series AC-MAX, DC-MAX Strobe - ac or dc, indoor/outdoor, 5 lens colors P83857 Catalog
Series MB Bell - 6 or 10-inch, 12 or 24 vdc P81960 Catalog
Series MT Multitone - 12/24 vdc or 115 vac P824671 Catalog
Series MT w/strobe Multitone Strobe - 12 vdc or 24 vdc or 115 vac P824677 Catalog
Series SA-H5-B Amplified Paging Horn Speaker - 5 watts P82580 Catalog
*To contact Technical Support call (800) 631-2148. Press #3.

For additional information and to print Adobe PDF files of Instruction Sheets and Data Sheets, visit
our website at www.wheelockinc.com.
08/04

2004 Catalog

Uploaded by

Copyright:

Available Formats

2004 Catalog

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

2004 Catalog

Uploaded by

Copyright:

Available Formats

TABLE OF CONTENTS Helping People Take ActionSM

AUDIBLE & STROBE APPLIANCES

SPEAKER & SPEAKER STROBE APPLIANCES

SYNC MODULES, POWER SUPPLIES & PULL STATIONS

FACILITY COMMUNICATIONS/AUDIO EVACUATION

TELEPHONE SIGNALING & COMMERCIAL AUDIO

MOUNTING, ACCESSORIES, REFERENCE

Visit www.wheelockinc.com to obtain:

273 Branchport Avenue • Long Branch, NJ 07740 • (800) 631-2148 • www.wheelockinc.com

Wheelock Fire Alarm Notification Appliance Circuit Products, Stand

To meet the growing demands for integrated systems

Wheelock also provides a broad range

If you are involved in solving SAFETY,

273 Branchport Avenue • Long Branch, NJ 07704 • (800) 631-2148 • www.wheelockinc.com

E-Learning On-Line Training Website

Customer Service: (800) 631-2148, Option #2

273 Branchport Avenue • Long Branch, NJ 07704 • (800) 631-2148 • www.wheelockinc.com

Specification and Ordering Information

#See mounting options pull out guide in

Average RMS Current

12V D C 0.010 0.155

Specification and Ordering Information

AS-24MCWH-FR 3468 135/185 X - X - X - B,D,E,F,G,H,J,N,O,R,X X * X * *

AS-24MCC-FR 3161 15/30/75/95 X - - X X - B,D,E,F,G,H,J,N,O,R,X X X X * *

AH-24-R 7892 - X - X X X - B,D,E,F,G,H,J,N,O,R,X X X X X X

AH-24WP-R 7416 - X - X X X - K (Outdoor) X X X * X

AH-12WP-R 7415 - - X X X X - K (Outdoor) X X X * X

Specification and Ordering Information

MT-12/24-W 5024 12/24 - D,E,F,L,M,O,P,R X X X X X

dBA and Current Ratings for Multitone Audible Portion

Horn 0.074 0.108 0.033 0.044 0.145 0.176 0.023 0.034 92 87 90 77 99 93

Bell 0.040 0.053 0.018 0.024 0.077 0.095 0.014 0.020 86 80 85 69 92 87

Siren 0.080 0.104 0.027 0.036 0.122 0.152 0.021 0.030 89 84 89 75 98 93

HI/LO 0.044 0.057 0.020 0.026 0.089 0.114 0.018 0.026 86 81 86 71 93 88

* RMS current ratings are per UL average RMS method. UL

Specification and Ordering Information

Current Ratings for AMT Multitone Audible Signals

UL Listed Models and Ratings

RSS-24MCC-FW 3158 - X 15/30/75/95 X - - X B,D,E,F,G,H,J,N,O,P,R,X Square X X X X *

RSSP-24MCWH-FR 9482 X 135/185 X X B,D,E,F,G,H,J,N,O,P,R,X Square X X X * *

Specification and Ordering Information

CH70-24MCWH-FR 9083 X - 135/185 X X - L,O,P,Q,R,U,Y X X X *

CH90-24MCC-FW 3168 - X 15/30/75/95 X - X Q,U,V X X X *

Average RMS Current

Order Shell Input Input dB A @ Mounting Agency Approvals

Specification and Ordering Information Series 31T

I B Hydrogen, or gases and vapors of equibalent hazards suh as manufactured gas

I C Ethyl and ether vapors

II F Carbon black, coal, coke dust

II G Flour, starch, grain dusts

Series ASWP Series AHWP

Hi/Lo 0.020 0.044 0.026 0.057

Features: Series E50 Series E50

Specification and Ordering Information Note: Available October 2004

Surface Agency Approvals

E50-R 0222 X X - Red 4' x 4" x 2-1/8" E50SB-R E,O,P,Q,R,U,Y,AA X * * * *

#See mounting options

E50 UL Reverberant dBA @ 10 Feet**

w atts 1/8 1/4 1/2 1 2

Specification and Ordering Information