Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 82 views

    Series 825Y Specification Sheet

    Uploaded by

    FEBCO
    FEBCO Series 825Y Reduced Pressure Zone Assemblies are used to protect against high hazard (toxic) fluids in water services to industrial plants, hospitals, morgues, mortuaries, and chemical plants. They are also used in irrigation systems, boiler feed, water lines and other installations requiring maximum protection.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd

    Series 825Y Specification Sheet

    Uploaded by

    FEBCO
    82 views2 pages
    FEBCO Series 825Y Reduced Pressure Zone Assemblies are used to protect against high hazard (toxic) fluids in water services to industrial plants, hospitals, morgues, mortuaries, and chemical plants. They are also used in irrigation systems, boiler feed, water lines and other installations requiring maximum protection.

    Copyright

    © Attribution Non-Commercial (BY-NC)

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    FEBCO Series 825Y Reduced Pressure Zone Assemblies are used to protect against high hazard (toxic) fluids in water services to industrial plants, hospitals, morgues, mortuaries, and chemical plants. They are also used in irrigation systems, boiler feed, water lines and other installations requiring maximum protection.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    82 views2 pages

    Series 825Y Specification Sheet

    Uploaded by

    FEBCO
    FEBCO Series 825Y Reduced Pressure Zone Assemblies are used to protect against high hazard (toxic) fluids in water services to industrial plants, hospitals, morgues, mortuaries, and chemical plants. They are also used in irrigation systems, boiler feed, water lines and other installations requiring maximum protection.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 2

    ES-F-825Y

    S P E C I F I C AT I O N S H E E T

    Series 825Y

    Reduced Pressure Zone Assemblies


    Size: 34" - 2" (20mm - 50mm)
    The FEBCO Series 825Y Reduced Pressure Zone Assemblies are used to protect against high hazard (toxic) fluids in water services to industrial plants, hospitals, morgues, mortuaries, and chemical plants. They are also used in irrigation systems, boiler feed, water lines and other installations requiring maximum protection. 825Y

    Features
    Ultimate mechanical protection of potable water, against hazards of cross-connection contamination. Meets all specifications of AWWA, ASSE, CSA and approved by the Foundation for Cross-connection Control and Hydraulic Research at the University of Southern California. Flow curve generated by the Foundation of Cross-Connection Control and Hydraulic Research at the University of Southern California. Modular relief valve for ease of maintenance. Simple Service procedures. All internal parts serviceable in line. Low head loss. Spring loaded "Y" type check valves. Internal relief valve pressure sensing passages. Replaceable seat rings on all sizes. End connection NPT ANSI / ASME B1.20.1

    Operation
    In a flow condition the check valves are open with the pressure between the checks, called the zone, being maintained at least 5.0psi lower than the inlet pressure and the relief valve is maintained closed. Should abnormal conditions arise under no flow or reversal of flow, the differential relief valve will open and discharge to maintain the zone at least 2psi lower than the supply. When normal flow resumes, the zones differential pressure will resume and the relief valve will close.

    Typical Installation
    Reduced pressure zone assemblies should be installed with minimum clearance of 12" (300mm) between relief valve discharge port and floor or grade. They must be installed where discharge will not be objectionable and can be positively drained away. They should be installed where easily accessible for testing and maintenance and must be protected from freezing. Thermal water expansion and/or water hammer downstream of the backflow preventer can cause excessive pressure. Excessive pressure situations should be eliminated to avoid possible damage to the system and assembly. Refer to local codes for specific installation requirements. Some codes may prohibit vertical installation.

    Specifications
    The reduced pressure zone assembly shall consist of two independently operating, spring loaded, "Y" pattern check valves and one hydraulically dependent differential relief valve. The assembly shall automatically reduce the pressure in the "zone" between the check valves to at least 5psi lower than inlet pressure. Should the differential between the upstream and the zone of the unit drop to 2psi, the differential relief valve shall open and maintain the proper differential. Mainline valve body and caps including relief valve body and cover shall be bronze. Check valve moving member shall be center stem guided. All hydraulic sensing passages shall be internally located within the mainline and relief valve bodies and relief valve cover. Diaphragm to seat area ratio shall be 10:1 minimum. Relief valve shall have a removable seat ring. Check valve and relief valve components shall be constructed so they may be serviced without removing the valve body from the line. All seat discs shall be reversible. Shutoff valves and test cocks shall be full ported ball valves. The assembly shall be rated to 175psi (12.1 bar) working pressure and water temperature range from 32F to 140F (0C - 60C). The assembly shall meet the requirements of ASSE Standard 1013; AWWA Standard Code C511; CSA Standard B64.4; and approved by the Foundation for Cross-Connection Control and Hydraulic Hydraulic Research at the University of Southern California. Job Name Job Location Engineer Approval

    30" Max. (700mm) 12" Min. (300mm)

    Flow

    Contractor Approval Contractors P .O. No. Representative

    FEBCO product specifications in U.S. customary units and metric are approximate and are provided for reference only. For precise measurements, please contact FEBCO. FEBCO reserves the right to change or modify product design, construction, specifications, or materials without prior notice and without incurring any obligation to make such changes and modifications on FEBCO products previously or subsequently sold.

    Capacity
    kPa psi 138 Headloss 103 69 34 20 15 10 5 0 0 5 19 10 38 15 57 20 76 25 95 15 4.6 30 gpm 114 lpm fps mps
    34

    Temperature Pressure
    " (20mm)

    Maximum working pressure: Hydrostatic test pressure: Temperature range:

    175psi (12.1 bar) 350psi (24.1 bar) 32F to 140F (0C to 60C)

    Materials
    Main valve body: Relief valve body: Elastomers: Diaphragms: Springs: Bronze Bronze Nitrile Seat Discs Nitrile, fabric reinforced Stainless Steel
    5 1.5 7.5 2.3 10 3.1

    kPa psi 138 Headloss 103 69 34 20 15 10 5 0 0 10 38 5 1.5 20 76 7.5 2.3

    1" (25mm)

    Approvals Standards
    30 114 10 3.1 40 151 15 4.6 50 190 60 gpm 227 lpm fps mps

    Approved by the Foundation for Cross-Connection Control and Hydraulic Research at the University of Southern California. AWWA C511 Conformance

    20 6.1

    kPa psi 138 Headloss 103 69 34 20 15 10 5 0 0 20 76 40 151

    112" (40mm)

    1013

    B64.4

    5 1.5

    60 227 7.5 10 2.3 3.1

    80 304

    100 379 15 4.6

    120 gpm 454 lpm fps mps

    kPa psi 138 Headloss 103 69 34 20 15 10 5 0 0 40 151 5 1.5 80 304 7.5 2.3

    2" (50mm)

    120 454 10 3.1

    160 606 15 4.6

    200 760 20 6.1

    240 gpm 910 lpm fps mps

    Side View A B

    Dimensions Weights
    Size: 34" - 2" (20 - 50mm)
    size (DN)
    A in. mm in. mm In. B* mm in.

    Dimensions
    C mm in. D mm in. E mm

    Weight
    lbs. kgs.

    1 112 2
    34

    20 25 40 50

    12 1234 17 1734

    305 324 432 451

    734 734 1012 1012

    197 197 267 267

    314 314 412 412

    83 83 114 114

    314 314 412 412

    83 418 83 418 114 5 114 5

    105 105 127 127

    11.5 5.2 12.5 5.7 26.5 12.0 29.0 13.0

    * B Dimension is less shutoffs Note: Weights shown are approximate. Dimensions shown are nominal, allowance must be made for normal manufacturing tolerances. E

    Top View

    A Watts Water Technologies Company

    USA: 4381 N. Brawley Ste. 102 Fresno, CA 93722 Tel. (559) 441-5300 Fax: (559) 441-5301 www.FEBCOonline.com Canada: 5435 North Service Rd. Burlington, ONT. L7L 5H7 Tel. (905) 332-4090 Fax: (905) 332-7068 www.FEBCOonline.ca

    ES-F-825Y 0949

    2009 FEBCO

    You might also like