Credit Evaluation System

Shaheed Bhagat Singh State Technical Campus
Moga Road (NH-95), Ferozepur-152004 (PB)

UGC Autonomous Institute Accredited By NAAC & NBA
Credit Evaluation System

For B.Tech. Programmes (2015 batch onwards)
1. Credit System:
A credit-based system with 160-200 credits required for graduation with
B.Tech. degree. In this system, the course credits will be computed based on the
student contact hours per week for the course using the following table:
Contact Hours Credit (C)
Lecture (L) 01 01
Tutorial (T) 01/02 01

02 or 03 01
Practical (P)
Above 03 02
Credit for a course C = L + T + P; where C is the number of credits, L is the

number of lecture hours, T is the number of tutorial hours and P is the number
of laboratory hours.
An average student, registered for normal load, is expected to register for 20-26
credits in each semester. In some courses, there may not be tutorials, then T = 0,
if Practicals are not there then P = 0. In case of Lab based courses, there may not
be lectures and tutorials so L and T both will be 0.
To categorize the performance of students as Outstanding, Excellent, good or

just Pass represented by an Alphabet as follows:
Grade Significance
A Outstanding Performance
B Excellent Performance
C Good Performance
D Satisfactory Performance (Pass)
Shaheed Bhagat Singh State Technical Campus, Ferozepur 1

F Unsatisfactory Performance (Fail)
Under this approach, student performances are first quantified as marks. Then,
the instructor assigns the following letter grades. The degree of difficulty in the
various examination papers, the leniency exercised in giving partial credits for
incomplete responses, and the instructors overall assessment of the student's
understanding of the subject, form the input to awarding letter grades.
Introduction of an E grade in the UG system has been deliberately avoided to

keep a future scope of introduction an addition performance level if required.
This grade may worth two points. An E grade, however, is not a passing grade,
but a student can use this grade to satisfy prerequisites. The description of the
various letter grades is:
Grade Weight Description

A 10 Outstanding
B 8 Excellent
C 6 Good
D 4 Pass
F 0 Fail
The Departmental Quality Assessment Committee (DQAC) will ensure that

grading must be done uniformly in a class. The following general criteria should
be followed
1. The average marks obtained by a class should be calculated and grade C

should correspond to the average marks.
2. The grade A should be given to the students getting marks more than 85% or
to the students at the most top 5% of the class.
3. Students getting marks below a pre-decided threshold (may 33% or so) will
be given F grade. This will be applicable after awarding grace marks etc. as
decided by competent forum/authority.
2. Semester and Cumulative Performance Index (SPI & CPI)
A student is awarded a letter grade in each course he/she is registered for,

including his/her overall performance in that course. There are five letter
grades: A, B, C, D and F on a scale of 0 to 10. If a student does not complete all
the requirements for a course for a genuine reason, the instructor may award
grade I (Incomplete). An I grade must be converted by the instructor to a regular
letter grade by the last date for such conversion specified in the programme
ordinances failing which it is automatically converted to an F grade. A student
getting F grade in a course must either repeat it or substitute it by another
course as per the provisions of programme ordinances.
A student getting a D grade in a course may be allowed to repeat it or substitute
it by another course, provided: his/her CPI is less than the prescribed minimum
and the student is allowed to continue in the programme as per provision in the
Academic Performance Requirement, and he/she has completed all the courses
as prescribed by the department. In case a course is repeated or substituted, the
old grade will also appear on the transcript, although it will not be taken into
account while computing the CPI/SPI.
Seminars, dissertations and projects will be given some credits as per the
Scheme Plan of the programme and these will also be graded using the aforesaid
scheme of grades A, B, C, D and F.
3. Computation of the Semester Performance Index (SPI) and Cumulative

Performance Index (CPI)
The SPI is an indicator of the overall academic performance of a student in all
the courses he/she has registered during a given semester. It is computed as
follows: If the grades awarded to student are G1, G2, etc in courses with
corresponding units U1, U2, etc, the SPI is given by:
U G i i
SPI  i
U i
i
In the above computation, non-credit course(s), if any, are to be ignored.

Similarly, the CPI indicates the cumulative academic performance in all the
courses taken including those taken in the current semester.
4. Degree options/Graduation Requirements

The graduation requirement is that the student collects all the credits that are
prescribed for that programme. Students who do well in the programme will be
awarded a distinction.
The minimum residence time for the BTech programme is 7 semesters. BTech
with Distinction will be awarded to students with a minimum CPI of 8.0 and
either an average CPI of 9.0 in department core or an average CPI of 8.0 in all UG
project courses. The normal academic load, for the purpose of evaluating
performance, is 20-26 credits per semester. The minimum SPI required for a
student in a semester is 03 and minimum value of CPI for award of degree is 4.5.
The semesters that the student may be on leave are excluded from the
computation.

Credit Evaluation System

Uploaded by

Copyright:

Available Formats

Credit Evaluation System

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Credit Evaluation System

Uploaded by

Copyright:

Available Formats

Shaheed Bhagat Singh State Technical Campus

Moga Road (NH-95), Ferozepur-152004 (PB)

Credit Evaluation System

Contact Hours Credit (C)

Tutorial (T) 01/02 01

Credit for a course C = L + T + P; where C is the number of credits, L is the

To categorize the performance of students as Outstanding, Excellent, good or

D Satisfactory Performance (Pass)

Shaheed Bhagat Singh State Technical Campus, Ferozepur 1

Introduction of an E grade in the UG system has been deliberately avoided to

Grade Weight Description

The Departmental Quality Assessment Committee (DQAC) will ensure that

1. The average marks obtained by a class should be calculated and grade C

2. Semester and Cumulative Performance Index (SPI & CPI)

A student is awarded a letter grade in each course he/she is registered for,

3. Computation of the Semester Performance Index (SPI) and Cumulative

In the above computation, non-credit course(s), if any, are to be ignored.

4. Degree options/Graduation Requirements

Shaheed Bhagat Singh State Technical Campus, Ferozepur 3

You might also like