How To Read/write Your Bosch EDC15 ECU Using The MPPS Tool: MPPS Programmer Guide HDI Tuning LTD WWW - Hdi-Tuning - Co.uk

MPPS programmer guide
HDI Tuning Ltd

www.hdi-tuning.co.uk
How to read/write your Bosch EDC15 ECU using the MPPS tool
This guide will explain how to setup the MPPS programmer tool. The MPPS programmer can be used to
read and write your Peugeot/Citroen EDC15C2 ECU.
Purchasing your MPPS tool

The best place to buy the MPPS tool is from eBay. This typically costs around £25 from a UK seller. It is
advisable to use a seller who sells tested tools.
Setup and installation

First , open Mpps Setup v12.0.0.6.exe
(if using an operating system later than windows XP you must right click the icon and then run in XP
compatibility mode).
The setup for your tool may

differ slightly depending on
the software version supplied
with your tool.
Select ‘Install’ to proceed.
Select your language and then

‘Next’ to proceed.
It is recommended that you

restart your computer after
the installation is complete.
When finished select ‘Finish’

to close the software.
Disclaimer: This information has been provided by HDI Tuning Ltd to help in programming your Bosch EDC15C2 ECU. By following this guide you
agree that all actions are taken at your own risk. We are not responsible for ECU damage caused by incorrect use of the tool described in this
document. However, HDI Tuning Ltd are capable of repairing an ECU in the event that programming does not complete successfully.
HDI Tuning Ltd
Insert the MPPS reader into
your computer's USB port.
Once you have inserted the
MPPS tool you should see
‘Found new hardware wizard’.
Select ’No, not this time’ from

the menu then select ‘Next’
(now you can locate the
driver manually).
From the menu select ’Install

from a list or specific location
(Advanced)’ then select ‘Next’
HDI Tuning Ltd
From the menu check ‘Search
for the best drivers in these
locations’ then check ‘Include
this location in the search.
Select ‘Browse’ you should

now get a small window open
to browse for the driver.
The driver location should be

located here:
‘C:\MPPS\Device Driver’
Once the folder has been

selected you can select ‘Next’
and windows will find the
driver in that folder.
HDI Tuning Ltd
Select ‘Finish’ to complete
installation.
HDI Tuning Ltd
Reading your original ECU data
The MPPS tool requires a stable laptop computer with a good battery. For best results use windows XP
and use a laptop with a fully charged battery. Contradictory to what some may say, we recommend you
don’t attach your laptop's power supply during flashing as this can induce a ground loop which may
crash the MPPS software. Instead, be certain you have at least 45 minutes of battery (the read/write
process only takes just over a minute, however after finding the OBD port, opening the software etc,
you may take longer than anticipated).
It is very important not to disturb your computer while you are reading/writing the ECU.
 Remain still to avoid moving any wires or connections.
 Close all other programs on your computer beforehand.
 Turn off fan, heated rear screen, remove fuses from any amplifiers, turn off the head unit or
remove the front (before starting this process).
1. Ensure your car is switched off. Locate the diagnostic port and connect the tool.
2. Connect the USB cable to your laptop.
3. Open the MPPS software through the shortcut on your desktop.
4. Once open, switch on your ignition to 2 clicks (until the engine check light is shown on your dash).
5. Select your car and engine from the menus provided.
6. Select ECU Id on the left.
HDI Tuning Ltd
7. Once the ECU number is displayed, you are ready to read your ECU. Select ‘Read’.
8. The reading process takes just over a minute to complete. Once completed, save the file in an
appropriate place with the file name of: YourName.bin
9. Once the read has finished,

follow the on screen steps to
switch off keys>wait 5
seconds>switch on keys
10. When finished, switch off

the ignition and close the
program by selecting ‘Exit’ in
the bottom left corner. It is
now safe to remove the OBD
lead from your car.
11. You can now email your

original ECU data to
remap@hdi-tuning.co.uk
HDI Tuning Ltd
Writing your ECU
1. Ensure your car is switched off. Locate the diagnostic port and connect the tool.
2. Connect the USB cable to your laptop.
3. Open the MPPS software through the shortcut on your desktop.
4. Once open, switch on your ignition to 2 clicks (until the engine check light is shown on your dash).
5. Select your car and engine from the menus provided.
6. Select ECU Id on the left.
7. Once the ECU number is displayed you can the select ‘write’.
8. Locate your remapped file and then select ‘ok’.
9. Once the write has finished, follow the on screen steps to switch off keys>wait 5 seconds>switch on
keys.
10. Once this is completed, switch off the ignition and close the program by selecting ‘Exit’ in the bottom
left corner. It is now safe to remove the OBD lead from your car.
Your car is now remapped and ready to go, take the car for a test drive and enjoy!
Be sure to leave a review on our Facebook page at www.facebook.com/HDITuningLimited
HDI Tuning Ltd
Trouble shooting during installation
Follow the guide below if windows fails to install the correct driver for your MPPS tool.
If installation was
unsuccessful, open the start
menu and right click on ‘My
computer’ then select
‘Manage’ from the drop down
menu
Once open, select ‘Device

manager’ from the menu on
the left.
Search through the list to find

any items with a yellow
question mark displayed to
the left.
HDI Tuning Ltd
Once the marked item has
been located, right click the
item and select ‘Properties’
from the drop down menu.
Select the tab named ‘Driver’

located at the top and then
select ‘Update Driver...’ to
proceed.
HDI Tuning Ltd
From the menu select ‘Search
for the best drivers in these
locations’ then select ‘Browse’
you should now get a small
window open to browse for
the driver.
Select the folder:

‘C:\MPPS\Device Driver’ then
select ‘Ok’ to proceed.
Once the driver folder has

been located ‘Select’ next to
proceed.
HDI Tuning Ltd
Select ‘Continue Anyway’ to
proceed.

How To Read/write Your Bosch EDC15 ECU Using The MPPS Tool: MPPS Programmer Guide HDI Tuning LTD WWW - Hdi-Tuning - Co.uk

Uploaded by

Copyright:

Available Formats

How To Read/write Your Bosch EDC15 ECU Using The MPPS Tool: MPPS Programmer Guide HDI Tuning LTD WWW - Hdi-Tuning - Co.uk

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

How To Read/write Your Bosch EDC15 ECU Using The MPPS Tool: MPPS Programmer Guide HDI Tuning LTD WWW - Hdi-Tuning - Co.uk

Uploaded by

Copyright:

Available Formats

MPPS programmer guide

HDI Tuning Ltd

Purchasing your MPPS tool

Setup and installation

The setup for your tool may

Select ‘Install’ to proceed.

Select your language and then

It is recommended that you

When finished select ‘Finish’

Select ’No, not this time’ from

From the menu select ’Install

Select ‘Browse’ you should

The driver location should be

Once the folder has been

2. Connect the USB cable to your laptop.

3. Open the MPPS software through the shortcut on your desktop.

5. Select your car and engine from the menus provided.

6. Select ECU Id on the left.

9. Once the read has finished,

10. When finished, switch off

11. You can now email your

2. Connect the USB cable to your laptop.

3. Open the MPPS software through the shortcut on your desktop.

5. Select your car and engine from the menus provided.

6. Select ECU Id on the left.

8. Locate your remapped file and then select ‘ok’.

Once open, select ‘Device

Search through the list to find

Select the tab named ‘Driver’

Select the folder:

Once the driver folder has

You might also like