Issued Jan. 2016 • Index No. DC/12.

58

Millermatic 211 ® MIG Power Source,

Wire Feeder and Gun Package

Light Industrial Processes Weld Thickness Input Power

Applications MIG (GMAW) 120 V: 24 ga.–3/16 in. steel 120 V: 24.3 A, 60 Hz, single-phase
Quick Light fabrication Flux-cored (FCAW) 18 ga.–1/8 in. aluminum 240 V: 16.6 A, 60 Hz, single-phase
Specs Maintenance and repair
Auto body
240 V: 24 ga.–3/8 in. steel
18 ga.–3/8 in. aluminum
Rated Output
120 V: 115 A at 19.8 VDC, 20% duty cycle
Farm/home 240 V: 150 A at 21.5 VDC, 40% duty cycle

120 or WEIGHS
ONLY
240 V
INPUT POWER 38lb.
Uses 120- or 240-volt power Portable

3∕8" L THICK
(9.5 mm) RIA
24 ga.

MATE

NE
SS
(0.8 mm)

Weld capacity Quick and easy setup

NEW! Advanced Auto-Set ™ now includes five NEW! Angled cast-aluminum drive system with Uses 4- or 8-inch (102 or 203 mm) spools
different wire/gas combinations and .024-inch calibrated tension knob creates consistent feeding and can be set up to weld with .024–.035 inch
(0.6 mm) wire capability. The easiest welder to and easy setup for up to 15-foot MIG guns. (0.6–0.9 mm) solid wire and .030–.045 inch
use just became more versatile. NEW! Quick Select™ drive roll makes setup quicker (0.8–1.2 mm) flux-cored wire.
• Wire/gas combinations include Flux Cored, by offering three grooves— two for different size
Mild Steel with 100% CO2, Mild Steel with C25, solid wire and a third for flux-cored wire. Comes complete with:
Stainless Steel, and Aluminum with spool gun Power source
• Select the wire type and gas being used NEW! Auto Spool Gun Detect™ automatically 6.5 ft. (2 m) power cord with MVP plugs
• Set the wire diameter, and select from .024, detects when a MIG gun or spool gun is for 120 V and 240 V
.030 and .035 diameters. A blue LED indicates connected eliminating the need for a switch. 10 ft. (3 m) M-100 MIG gun and cable
that Auto-Set is activated NEW! Fan-On-Demand™ power source cooling assembly
• Dial in the thickness of what you’re welding system operates only when needed, reducing 10 ft. (3 m) work cable with clamp
• Start welding with the exact parameters noise, energy use and the amount of Flow gauge regulator and gas hose for
you need! contaminants pulled though the machine. argon and AR/CO2 mix
Hobart® spool of .030 in. (0.8 mm)
NEW! Inverter technology combines best-in-class NEW! Smooth-Start ™ provides a smooth,
solid wire
arc characteristics with the portability of a spatter-free start. It’s the best-starting machine
Two contact tips for .030 in. (0.8 mm) wire
38-pound machine. The arc is extremely forgiving in the small MIG machine category.
Quick Select ™ drive rolls for .024 in.
to variations in arc length and travel speeds. Thermal overload protection shuts down unit (0.6 mm) or .030/.035 in. (0.8/0.9 mm)
Multi-voltage plug (MVP) and activates the over temperature light if solid wire, and .030/.035 in.
allows connection to airflow is blocked or duty cycle is exceeded. (0.8/0.9 mm) flux-cored wire
common 120- and 240- Automatically resets when unit cools. Material thickness gauge
volt power receptacles 229895
without the use of any Hook-and-loop cord wraps
tools — simply choose the plug that fits the Note: Shielding gas and
receptacle and connect to the power cord. safety equipment not included.
Welder is warranted for three years, parts and labor.
Gun warranted for 90 days, parts and labor.

Miller Electric Mfg. Co. Equipment Sales US and Canada MillerWelds.com

An ITW Welding Company Phone: 866-931-9730
1635 West Spencer Street FAX: 800-637-2315
P.O. Box 1079 International Phone: 920-735-4554
Appleton, WI 54912-1079 USA International FAX: 920-735-4125
 Operation Modes
Auto-Set ™ mode
Auto-Set eliminates guesswork and saves you time on setup. Turn wire selector knob to select
the wire and gas combination being used. Turn wire speed control fully clockwise to select
Auto-Set mode and set the wire diameter to either .024, .030 or .035 inch. The Auto-Set light
indicates mode is activated. Then select material thickness using the Auto-Set control.
Use Auto-Set when you want the speed, convenience and confidence of pre-set controls.
Auto-Set automatically sets your welder to the proper parameters. It’s available for welding
with .024-, .030- and .035-inch steel and stainless steel wires, .030- and .035-inch flux-cored
wires, and .030- and .035-inch 4043 aluminum wires with the Spoolmate 100 spool gun.
Shielding gas is dependent on the wire being used.
Manual mode
When welding outside of Auto-Set
capabilities, or if you prefer custom
parameters, use manual mode. The
parameter chart on the inside of the access
door is an easy-to-use guide for determining
your voltage and wire feed speed settings.
To optimize arc starts, turn wire selector
knob to select the wire and gas combination
being used. Reference the white areas on the
controls when welding in manual mode.

Specifications (Subject to change without notice.)

Input Amperage Amps Input at Rated Output, 60 Hz Wire Type Max. Open-Circuit Net
Power Range Rated Output 120 V 240 V KVA KW Wire Feed Speed and Diameter Voltage Dimensions Weight
120 V 30–130 A 115 A at 19.8 VDC, 24.3 – 2.9 2.9 60 – 600 ipm Solid/stainless: 54 H: 12.5 in. 38 lb.
20% duty cycle (1.5 –15.2 m/min.) .024–.035 in. (318 mm) (17.2 kg)
(0.6–0.9 mm) W: 11.25 in. 42 lb.
150 A at 21.5 VDC, – 16.6 4.0 4.0 Flux-cored: (286 mm) (19.1 kg)
240 V 30–230 A
40% duty cycle .030–.045 in. D: 20.5 in. with gun
(0.8–1.2 mm) (521 mm)

Certified by Canadian Standards Association to both the Canadian and U.S. Standards.

Control Panel Performance Data

Duty Cycle Chart
250
1 240 V
1. Power On Light 200
2
Weld Amperes

2. Over Temperature Light

150
3. Auto-Set Light 120 V, 20 A
3
4. Wire Speed/Wire Diameter Control 100

4 5. Wire Selector Knob

50
5 6. Voltage/Material Thickness Control
6 7. Plastic Hub with Retaining Ring for 0
7 10 20 30 40 50 60 70 80 90100
8-inch Spools (shaft also accepts % Duty Cycle
4-inch spools)
8. Calibrated Tension Knob Volt/Amp Curves
100
8 9. T-Knob (secures torch)
10. Drive Roll 80
11. Trigger Control Connector
Volts

60
9 12. Polarity Changeover Terminals
10
40
Note: Power switch and gas solenoid are 240 V Maximum
on machine back panel.
11 20
120 V Maximum
12 0
120/240 V Minimum
0 25 50 75 100 125 150 175 200 225
Amps

2
 Genuine Miller Accessories ®

Replacement/Optional MIG Gun Spoolmate™ 150 Running Gear/

M-100 (Standard) Spool Gun 301272 Cylinder Rack
248282 10 ft. (3 m) Direct-connect 301239
spool gun for all Heavy-duty
M-150 (Optional)
Millermatic 211 and construction with
249040 12 ft. (3.7 m)
Multimatic 200 8-inch rubber rear
249041 15 ft. (4.5 m)
models. Handles wheels. Convenient
All ship with liner 194011. .030–.035 inch front handles, cable
(0.8–0.9 mm) 4000/5000 series aluminum and holders and plastic
Spoolmate™ 100 consumable box.
.023–.035 inch (0.6–0.9 mm) steel/stainless
Spool Gun 300371 steel wires. Rated at 150 amps, 60-percent duty For gas cylinders no greater than 7 inches
Direct-connect cycle. Includes 20-foot (6.1 m) cable assembly. (178 mm) in diameter or 65 pounds (29.5 kg)
spool gun for all in weight.
Millermatic 140, 141,
180, 190, 211 and
Multimatic 200 Purchase the Millermatic 211 package
models. Handles (951603) and receive the Millermatic 211
.030–.035 inch (0.8–0.9 mm) aluminum and running gear/cylinder rack (301239)
(4043 only) and .023–.035 inch (0.6–0.9 mm) packaged together!
steel/stainless steel wires. Rated at 135 amps,
30-percent duty cycle. Includes 12-foot (3.7 m)
cable assembly and custom carrying case.
Millermatic Protective Cover 301262

Consumables (Order from Miller Service Parts.)

For M-100/M-150 Gun For Spoolmate™ 100 Spool Gun

Contact Tips Contact Tips (5 per package)

087299 .024 in. (0.6 mm) 199730 .024 in. (0.6 mm)
000067 .030 in. (0.8 mm) 186419 .030 in. (0.8 mm)
000068 .035 in. (0.9 mm) 186406 035 in. (0.9 mm)
000069 .045 in. (1.2 mm) Drive Rolls
Quick Select ™ 261157
For .024-inch (0.6 mm) or .030/.035-inch Nozzle 186405
(0.8/0.9 mm) solid wire, and .030/.035-inch
(0.8/0.9 mm) flux-cored wire.
Contact Tip Adapter 169716
Dual Groove, V-Knurled 202926
For Spoolmate™ 150 Spool Gun
For .030/.035-inch (0.8/0.9 mm) or
.045-inch (1.2 mm) flux-cored wire.
Replacement Liners
194010 .024 in. Contact Tips (5 per package)
194011 .030–.035 in. (standard) 199387 .030 in. (0.8 mm)
194012 .035–.045 in. 199388 .035 in. (0.9 mm)
15-foot length — trim to size needed.

Nozzle 199386

Nozzle 169715 M-Series Gun Consumable Kits

1/2-inch (13 mm) diameter orifice. 234607 .024 in. (0.6 mm) For Both Spool Guns
Nozzle flush with contact tip (standard). 234608 .030 in. (0.8 mm)
234609 .035 in. (0.9 mm)
Gasless Flux-Cored Nozzle Each kit contains ten contact tips, one nozzle, Drive Roll (1) 186413
#226 190 and one contact tip adapter. For .030/.035-inch
For M-100 gun only. (0.8/0.9 mm) wire.
For use with self-shielding
flux-cored wires. Improves
visibility, eases access in tight corners, protects Push Roll (1) 186414
tip adapter/gas diffuser from spatter and from For .030/.035-inch
shorting to the workpiece. (0.8/0.9 mm) wire.

3
 Typical Installations

MIG (GMAW) or Flux-Cored (FCAW) Shielding

gas cylinder MIG gun
Basic Equipment

Work

Aluminum MIG (GMAW) Shielding Optional spool gun

Basic Equipment gas cylinder

Work

Ordering Information
Power Source and Options Stock No. Description Qty. Price

Millermatic® 211 907614 120/240 V, 60 Hz

Millermatic® 211 with Running Gear/Cyl Rack 951603 Power source packaged with 301239 running gear/cylinder rack

Guns
M-100 Gun (Standard) 248282 10 ft. (3 m), .030 –.035 in. (0.8 – 0.9 mm)
M-150 Gun (Optional) 249040 12 ft. (3.7 m), .030 –.035 in. (0.8 – 0.9 mm)
249041 15 ft. (4.5 m), .030 –.035 in. (0.8 – 0.9 mm)
Spoolmate™ 100 Spool Gun 300371 12 ft. (3.7 m). Includes custom carrying case
Spoolmate™ 150 Spool Gun 301272 20 ft. (6.1 m)

Accessories
Protective Cover 301262
Running Gear/Cylinder Rack 301239
Material Thickness Gauge 229895
Flux-Cored Wire
Solid Wire
Shielding Gas Cylinder
Helmet/Gloves/Scratch Brush

Available Through Miller Service Parts

Flow Gauge Regulator for Argon or AR/CO2 Mix 268546 Replacement standard regulator
Flow Gauge Regulator for CO2 212492 Required if using 100-percent CO2 gas
Contact Tips See page 3
Contact Tip Adapter 169716 For M-100 and M-150 guns
Replacement Liners See page 3
Nozzles See page 3
Gasless Flux-Cored Nozzle 226190 For M-100 gun
Drive Rolls See page 3
M-Series Gun Consumable Kits 234607 .024 in. (0.6 mm)
234608 .030 in. (0.8 mm)
234609 .035 in. (0.9 mm)

Date: Total Quoted Price:

Distributed by:

© 2016 Miller Electric Mfg. Co.