Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                

Compact Pneumatic Cylinder

Download as pdf or txt
Download as pdf or txt
You are on page 1of 20

CAT.

EUS20-184 A -UK

ISO Standard [ISO 21287]


Compact Cylinder

Series C55
ISO Standard [ISO 21287]
Compact Cylinder

Series C55
ø20, ø25, ø32, ø40, ø50, ø63

How to Order

Without
auto switch C55 B 20 10
With auto switch CD55 B 20 10 M9B S
Built in magnet Number of auto switches
- 2 pcs.
S 1 pc.
Mounting style
n “n” pcs.
Through-hole/Both ends
B tapped common (Standard)
L Foot style Bore size
F Rod side flange style Auto switch
20 20 mm
G Head side flange style - Without auto switch (Built-in magnet cylinder)
25 25 mm
C Single clevis style 32 32 mm ∗ For the applicable auto switch model, refer to the table below.
∗ Auto switches are shipped together, (but not assembled).
40 40 mm
50 50 mm
63 63 mm
Rod end thread
- Rod end female thread
Cylinder stroke (mm) M Rod end male thread
Refer to the next page for standard
and intermediate strokes.

Applicable Auto Switches/Refer to pages 12 to 17 for further information on auto switches.


Auto switch model Lead wire length (m) ∗
Indicator

Special Electrical Wiring Load voltage Pre-wired Applicable


light

Type Electrical entry direction 0.5 3 5


function entry (Output) DC AC connector load
Perpendicular In-line (Nil) (L) (Z)
3-wire IC
(NPN equivalent) — 5V — A96V A96   — — circuit —
switch

Yes
Reed

— Grommet 12 V 100 V A93V A93   — — — Relay,


2-wire 24 V IC
— 5 V, 12 V 100 V or less A90V A90   — — circuit
PLC
3-wire (NPN) 5V M9NV M9N     IC
— 3-wire (PNP) 12 V M9PV M9P     circuit
Solid state switch

2-wire 12 V M9BV M9B     —


Diagnostic 3-wire (NPN) 5V M9NWV M9NW     IC Relay,
indication 12 V circuit PLC
Grommet Yes 3-wire (PNP) 24 V — M9PWV M9PW    
2-colour
indication M9BWV M9BW    
Water
resistant 2-wire 12 V —
— M9BA —   —
2-colour
indication
∗ Lead wire length symbols: 0.5 m ·········· Nil (Example) M9N
3 m ·········· L (Example) M9NL
5 m ·········· Z (Example) M9NZ
∗  solid state auto switch is available after receiving an order.

1
ISO Standard [ISO 21287] Compact Cylinder Series C55

Specifications

Type Pneumatic (Non-lube)


Action Double acting, Single rod
Fluid Air
Proof pressure 1.5 MPa
Maximum operating pressure 1.0 MPa
Minimum operating pressure 0.05 MPa
Without auto switch: –10 to 70°C (No freezing)
Ambient and fluid temperature
With auto switch: –10 to 60°C (No freezing)
Cushion Rubber bumper on both end
Stroke length tolerance +1.0 mm
0
Mounting Through-hole/Both ends tapped common
Caution Piston speed 50 to 500 mm/s
 Be sure to read before handling. Refer to Best
Pneumatics catalogue for Safety
Instructions, Actuators and Auto Switches Standard Stroke
Precautions.
 This product should not be used as a stopper.
 Use the PF thread fittings for this cylinder Bore size (mm) Standard stroke (mm)
20 to 63 5, 10, 15, 20, 25, 30, 35, 40, 45, 50, 60, 80, 100, 125, 150

Theoretical
Output OUT IN Manufacture of Intermediate Stroke
Unit: N
Operating pressure (MPa) Dealing with the stroke by the 1 mm interval by using an exclusive body
Bore size Operating Description
with the specified stroke
(mm) direction 0.3 0.5 0.7
Part no. Refer to “How to Order” for the standard model no. (page at left)
IN 71 118 165
20 Stroke range 6 to 149
OUT 94 157 220
Part no.: C55B32-47
IN 113 189 264 Example
25 Makes 47 stroke tube
OUT 147 245 344
IN 181 302 422
32
OUT 241 402 563
Weight
IN 317 528 739
40 Without Auto Swtich Unit: g
OUT 377 628 880
Bore size Cylinder stroke (mm)
IN 495 825 1150 (mm)
50 5 10 15 20 25 30 35 40 45 50 60 80 100 125 150
OUT 589 982 1370
20 111 124 137 150 163 176 189 202 215 228 254 306 357 422 487
IN 841 1400 1960
63 25 152 168 183 199 214 230 246 261 277 292 323 386 448 526 603
OUT 935 1560 2180
32 250 273 295 317 339 362 384 406 428 451 495 584 673 785 896
40 315 339 364 388 412 436 461 485 509 533 582 679 776 897 1018
Mounting Bracket Part No. 50 497 534 570 607 644 681 718 755 791 828 902 1049 1197 1381 1565
63 677 717 757 797 837 877 917 957 997 1037 1117 1277 1437 1638 1838
Bore size Single
(mm)
Foot Flange
clevis With Auto Switch (Built-in magnet) Unit: g
Bore size Cylinder stroke (mm)
20 C55-L020 C55-F020 C55-C020
(mm) 5 10 15 20 25 30 35 40 45 50 60 80 100 125 150
25 C55-L025 C55-F025 C55-C025
20 113 126 139 152 165 178 191 204 216 229 255 307 359 424 489
32 C55-L032 C55-F032 C55-C032
25 154 170 185 201 217 232 248 263 279 294 325 388 450 528 606
40 C55-L040 C55-F040 C55-C040
32 254 277 299 321 343 366 388 410 432 455 499 588 677 788 900
50 C55-L050 C55-F050 C55-C050
40 319 344 368 392 416 441 465 489 513 537 586 683 780 901 1022
63 C55-L063 C55-F063 C55-C063
50 502 539 575 612 649 686 723 760 796 833 907 1054 1202 1386 1570
• Order two foot brackets per cylinder.
• Parts belonging to each bracket are as follows. 63 685 725 765 805 845 885 925 965 1005 1045 1125 1285 1445 1645 1845
Foot, Flange, Single clevis/Body mounting bolt Add each weight of auto switches and mounting brackets when mounting an auto switches.
Refer to pages 14 to 17 for auto switch weight.

2
Series C55

Allowable Lateral Load Allowable Kinetic Energy


Make sure to operate strictly within the allowable lateral load Make sure to operate strictly within the allowable range of
range to the rod end. the load weight and maximum speed.
Operation outside of this range may result in shorter service life or dama- Operation outside of this range may cause excessive impact, which may
ge to the device. result in the damage to the device.
Lateral load Operating pressure: 1 MPa
1000

500
300
Stroke 200
Eccentric distance 100
100

Load weight (kg)


10
ø63
Allowable lateral load (N)

ø50
ø63 ø40
1
ø32
10 ø50 ø25
ø40 ø20
ø32
0.1
ø25 10 100 200 300 500 1000

ø20 Maximum piston speed (mm/s)

1
0 50 100 150 200

Stroke + Eccentric distance (mm)

∗ Refer to Model Selection in Best Pneumatics catalogue for details about model selection procedure.

3
ISO Standard [ISO 21287] Compact Cylinder Series C55

Construction
ø20, ø25 With auto switch (Built-in magnet)

i t r !4 !2 y q e !3 o w u !0

ø32 to ø63 With auto switch (Built-in magnet)

!2 r t i !4 y q e !3 o w u !0

!1

M: Rod end male thread

Component Parts Replacement Parts: Seal Kit


No. Description Material Note Bore size
Kit no. Contents
1 Cylinder tube Aluminum alloy Hard anodized (mm)
2 Piston Aluminum alloy Chromated 20 CQ2B20-PS
Stainless steel ø20, ø25 25 CQ2B25-PS
3 Piston rod Set of nos.
Carbon steel ø32 to ø63 Hard chrome plated 32 CQ2B32-PS
above
Aluminum alloy ø20 to ø40 Anodized 40 CQ2B40-PS
!2, !3, !4
4 Collar
Aluminum alloy casted ø50, ø63 Painted after chromated 50 CQ2B50-PS
5 Snap ring Carbon tool steel Phosphate coated 63 CQ2B63-PS
6 Bumper A Urethane ∗ Seal kit includes !2, !3, !4. Order the seal kit,
7 Bumper B Urethane based on each bore size.
Oil-impregnated sintered alloy ø20, ø25
8 Bushing
Phosphor bronze alloy ø32 to ø63
9 Wear ring Resin
10 Magnet —
11 Rod end nut Carbon steel Nickel plated
12 Rod seal NBR
13 Piston seal NBR
14 Tube gasket NBR
4
Series C55

Mounting Bolt

Should use recommended bolt shown as below table Mounting


when mounting the cylinder using through-hole. bolt OA thread

Note) To install a through-hole type mounting bolt, bore size 20 to 63 mm,


make sure to use the flat washer that is provided.

Mounting Bolt for C55

Model C D Mounting bolt Model C D Mounting bolt Model C D Mounting bolt


C(D)55B20-5 45 M4 x 45 l C(D)55B32-5 55 M5 x 55 l C(D)55B50-5 55 M6 x 55 l
-10 50 x 50 l -10 60 x 60 l -10 60 x 60 l
-15 55 x 55 l -15 65 x 65 l -15 65 x 65 l
-20 60 x 60 l -20 70 x 70 l -20 70 x 70 l
-25 65 x 65 l -25 75 x 75 l -25 75 x 75 l
7.2
-30 70 x 70 l -30 80 x 80 l -30 80 x 80 l
-35 75 x 75 l -35 10 85 x 85 l -35 8.4 85 x 85 l
-40 80 x 80 l -40 90 x 90 l -40 90 x 90 l
-45 85 x 85 l -45 95 x 95 l -45 95 x 95 l
-50 90 x 90 l -50 100 x 100 l -50 100 x 100 l
-60 -60 110 x 110 l -60 110 x 110 l
Fix the cylinder by using
-80 the OA thread that are -80 130 x 130 l -80 130 x 130 l
-100 provided with the cylinder -100 150 x 150 l -100 150 x 150 l
-125 tube. -125 Fix the cylinder by using the OA -125 Fix the cylinder by using the OA
thread that are provided with the thread that are provided with the
-150 -150 cylinder tube. -150 cylinder tube.
C(D)55B25-5 50 M4 x 50 l C(D)55B40-5 55 M5 x 55 l C(D)55B63-5 60 M6 x 60 l
-10 55 x 55 l -10 60 x 60 l -10 65 x 65 l
-15 60 x 60 l -15 65 x 65 l -15 70 x 70 l
-20 65 x 65 l -20 70 x 70 l -20 75 x 75 l
-25 70 x 70 l -25 75 x 75 l -25 80 x 80 l
10.2
-30 75 x 75 l -30 80 x 80 l -30 85 x 85 l
-35 80 x 80 l -35 9 85 x 85 l -35 9.4 90 x 90 l
-40 85 x 85 l -40 90 x 90 l -40 95 x 95 l
-45 90 x 90 l -45 95 x 95 l -45 100 x 100 l
-50 95 x 95 l -50 100 x 100 l -50 105 x 105 l
-60 -60 110 x 110 l -60 115 x 115 l
-80 Fix the cylinder by using -80 130 x 130 l -80 135 x 135 l
the OA thread that are
-100 provided with the cylinder
-100 150 x 150 l -100 155 x 155 l
-125 -125 Fix the cylinder by using the OA -125 Fix the cylinder by using the OA
tube. thread that are provided with the thread that are provided with the
-150 -150 cylinder tube. -150 cylinder tube.

5
ISO Standard [ISO 21287] Compact Cylinder Series C55

Dimensions
ø20, ø25
2-M5
Auto switch
Port size

Q F 5.5 2 x 4-øOB H thread


2 counterbore RB effective depth C

øI

4-øN through
T
øD

M
E
Flat washer
2 x 4-OA ø20
4 pcs.
2 x 4-RA (RB) K
L B + Stroke M
A + Stroke E

ø25

Basic Style (mm)


Bore size
A B C D E F H I K L M N OA OB Q RA RB T
(mm)
20 43 37 10 10 36 5.5 M6 43 8 6 22 4.5 M5 7.5 13 10 5 0.8
25 45 39 10 12 40 5.5 M6 48 10 6 26 4.5 M5 7.5 13 10 5 0.8

Width across flats K M: Rod end male thread


H
øD

Hexagon width across flats B1 H1


Rod end nut ∗
C
X
L

Rod End Male Thread (mm)


Bore size
B1 C D H H1 K L X
(mm)
20 13 14 10 M8 5 8 22 16
25 13 14 12 M8 5 10 22 16

6
Series C55

Dimensions
ø32 to ø63
2-G1/8 Auto switch
Port size

Q F 2 x 4-øOB Z H thread
counterbore RB effective depth C

J
øI

4-øN through
T
øD

M
E
Flat washer
2 x 4-OA
4 pcs.
2 x 4-RA (RB) K
L B + Stroke M
A + Stroke E

Basic Style (mm)


Bore size
A B C D E F H I J K L M N OA OB Q RA RB T Z
(mm)
32 51 44 12 16 46 8.5 M8 59 2 14 7 32.5 5.5 M6 9 14.5 11 5 1 15
40 52 45 12 16 52 9.5 M8 67 3 14 7 38 5.5 M6 9 14.5 11 5 1 17
50 53 45 16 20 64 10.5 M10 82 2 17 8 46.5 6.6 M8 10.5 13.5 11 5 1.6 17
63 57 49 16 20 74 14.5 M10 96 3 17 8 56.5 6.6 M8 10.5 15.5 11 5 1.6 17

Width across flats K


M: Rod end male thread
H
øD

Hexagon width across flats B1 H1


Rod end nut ∗
C
X
L

Rod End Male Thread (mm)


Bore size
B1 C D H H1 K L X
(mm)
32 17 16.5 16 M10 x 1.25 6 14 26 19
40 17 16.5 16 M10 x 1.25 6 14 26 19
50 19 19.5 20 M12 x 1.25 7 17 30 22
63 19 19.5 20 M12 x 1.25 7 17 30 22

7
ISO Standard [ISO 21287] Compact Cylinder Series C55

Mounting Bracket
Foot bracket Flange bracket
Hexagon socket
head cap screw
(accessory) FL
2 x øFD 4 x øFD

M
Hexagon socket
head cap screw
R øD

FX
FZ

M
M/2
LH

2 x øLD
L
LT

LX
FT FY
Y X LZ
M
ø20, ø25 ø32 to ø63 FV

(mm) (mm)
Hexagon Hexagon
Bore size socket Bore size socket
(mm) L LD LH LT LX LZ M R X Y head cap
(mm) DH11 M FD FL FT FV FX FY FZ head cap
screw screw

20 22 7 27 4 22 36 22 8 16 7 M5 20 16 22 6.6 2.8 8 38 55 — 68 M5
25 22 7 29 4 26 40 26 10 16 7 M5 25 16 26 6.6 2.8 8 38 60 — 73 M5
32 24.5 7 33.5 4 32 46 32.5 15 16 7 M6 32 30 32.5 7 5 10 50 64 32 79 M6
40 26 10 38 4 36 52 38 17.5 18 9 M6 40 35 38 9 5 10 55 72 36 90 M6
50 31 10 45 5 45 64 46.5 20 21 9 M8 50 40 46.5 9 6 12 70 90 45 110 M8
63 31 10 50 5 50 74 56.5 22.5 21 9 M8 63 45 56.5 9 6 12 80 100 50 120 M8

Single clevis bracket

CL Hexagon socket head cap screw


(accessory)

øCD hole H9
CZ
M

CX
M CU
CZ CW RR

(mm)
Hexagon
Bore size socket
(mm)
CDH9 CL CU CW CX-0.2
-0.6 CZ M RR head cap
screw
20 8 3 12 20 16 35 22 9 M5
25 8 3 12 20 16 40 26 9 M5
32 10 5.5 12 22 26 45 32.5 9.5 M6
40 12 5.5 15 25 28 51 38 12 M6
50 12 6.5 15 27 32 64 46.5 12 M8
63 16 6.5 20 32 40 74 56.5 16 M8

8
Series C55

Proper Auto Switch Mounting Position (Detection at Stroke End) and Its Mounting Height

Reed switch Solid state switch


D-A9 D-M9 A B W ≈ Hs
D-M9BAL
D-M9 W
ø20, 25

A B W ≈ Hs

ø32, 40, 50, 63

∗ Figures in the table below are used as a reference when mounting the auto
switches for stroke end detection. In the case of actually setting the auto
switches, adjust them after confirming their operation. (mm)

Auto switch model D-M9


D-A9 D-M9BAL
D-M9 W

Symbol A B W A B W A B W Hs
20 11.5 5.5 3.5(1) 15.5 9.5 -0.5 14.5 8.5 -9.5 22
25 11.5 7.5 5.5(3) 15.5 11.5 1.5 14.5 10.5 -7.5 24
Bore size 32 15 9 7 (4.5) 19 13 3 18 12 -6 27
(mm) 40 16 9 7 (4.5) 20 13 3 19 12 -6 30
50 9.5 15.5 13.5(11.5) 13.5 19.5 9.5 12.5 18.5 0.5 36
63 11.5 17.5 15.5(13.5) 15.5 21.5 11.5 14.5 20.5 2.5 41
The dimension inside ( ) is for D-A93.

Reed switch Solid state switch A B ≈ Hs


D-A9 V D-M9 V
D-M9 WV
ø20, 25

A B ≈ Hs

ø32, 40, 50, 63

∗ Figures in the table below are used as a reference when


mounting the auto switches for stroke end detection. In the
case of actually setting the auto switches, adjust them after
confirming their operation.
(mm)

Auto switch model D-M9 V


D-A9 V
D-M9 WV

Symbol A B Hs A B Hs
20 11.5 5.5 22 15.5 9.5 24
25 11.5 7.5 24 15.5 11.5 26
Bore size 32 15 9 27 19 13 29
(mm) 40 16 9 30 20 13 32
50 9.5 15.5 36 13.5 19.5 38
63 11.5 17.5 41 15.5 21.5 43

9
ISO Standard [ISO 21287] Compact Cylinder Series C55

The Number of Surfaces and Grooves Where an Auto Switch Can Be Mounted (As Direct Mounting)

The number of the surfaces and grooves where the auto switch can be mounted, by switch type, are shown in the table below.

Switch model D-A9씲, M9씲


Bore size A B C D
Piping port (mm) (Mounting (Mounting (Mounting (Mounting
groove no.) groove no.) groove no.) groove no.)
A
   
20 (1) (2) (2) (2)
   
25 (2) (2) (2) (2)
D B    
32 (2) (2) (2) (2)
View from    
piston rod end
40 (2) (2) (2) (2)
C    
50 (2) (2) (2) (2)
   
63 (2) (2) (2) (2)

Operating Range
(mm)
Bore size
Auto switch model
20 25 32 40 50 63
D-M9씲W(V)
5 5.5 6 6 6 6.5
D-M9BAL
D-A9씲(V) 9 9 9 9 9 10.5
D-M9씲(V) 3 3.5 3.5 3.5 3.5 4
∗ The operating ranges are provided as guidelines including hystereses and
are not guaranteed values (assuming approximately ±30% variations).
They may vary significantly with ambient environments.

Minimum Auto Switch Mounting Stroke


(mm)
Bore size Auto switch model
(mm) D-A9쏔 A9쏔V D-M9쏔 D-M9쏔V D-M9쏔W D-M9쏔WV D-M9BAL
Number of auto switches
2 pcs. 10 10 15 5 15 10 20
20
1 pc. 10 5 15 5 15 5 20
2 pcs. 10 10 10 5 10 10 20
25,32,40,50
1 pc. 10 5 10 5 10 5 20
2 pcs. 10 10 10 5 10 10 15
63
1 pc. 5 5 5 5 10 5 15

Besides the models listed in “How to Order,” the following auto switches are applicable.
Refer to Best Pneumatics for detailed specifications.

Type Part no. Electrical entry Features


D-F9G Normally closed (N.C. = b contact), 3-wire
Solid state switch Grommet (In-line)
D-F9H Normally closed (N.C. = b contact), 2-wire

10
Series C55

Mounting of Auto Switch


To mount auto switches, follow the instruction illustrated below.

ø20 to ø63 /Direct mounting

Watchmakers’ screw driver

Auto switch mounting screw

Auto switch

• Use a watchmakers’ screwdriver with a handle 5 to 6 mm in diameter when tightening the auto
switch mounting screw.
Tightening torque should be set 0.10 to 0.20 N.m.

11
Series C55
Auto Switch Specifications
Auto Switch Common Specifications

Type Reed switch Solid state switch


Leakage current None 3-wire: 100 µA or less 2-wire: 0.8 mA or less
Operating time 1.2 ms 1 ms or less
Impact resistance 300 m/s2 1000 m/s2
Insulation resistance 50 MΩ or more at 500 VDC Mega (between lead wire and case)
Withstand voltage 1000 VAC for 1 minute (between lead wire and case)
Ambient temperature –10 to 60°C
Enclosure IEC529 standard IP67, Immersible construction (JIS C 0920)

Lead Wire Length Contact Protection Boxes: CD-P11, CD-P12


Lead wire length indication <Applicable switch model>
D-A9/A9쏔V
(Example) D-M9P L The above auto switches do not have internal contact protection circuit.
1. Operating load is an inductive load.
Lead wire length 2. The length of wiring to the load is 5 m or more.
Nil 0.5 m 3. The load voltage is 100 VAC.
L 3 m The contact life may be shortened. (Due to permanent energising conditions.)
Z 5 m
Note 1) Applicable auto switch with 5 m lead wire “Z”
Solid state switch: Manufactured upon receipt of order as standard.
Note 2) The standard lead wire length of solid state switch with water resistant Specifications
2-colour indication type is 3 meters. (Not available 0.5 m) Part No. CD-P11 CD-P12
Note 3) To designate solid state switches with flexible specifications, add “-61”
after the lead wire length. Load voltage 100 VAC 200 VAC 24 VDC
Maximum load current 25 mA 12.5 mA 50 mA
∗ Lead wire length Switch conneciton side 0.5 m
(Example) D-M9NWL- 61 Load connection side 0.5 m

Flexible specification
Note) D-M9쏔(V) series use flexible lead wire as standard.

Auto Switch Hysteresis Internal Circuits


The hysteresis is the difference between the position of the auto switch as CD-P11 OUT Brown
Choke
it turns “on” and as it turns “off”. A part of operating range (one side) Surge absorber coil
includes this hysteresis.
OUT Blue

Choke coil
CD-P12 OUT (+)
Brown
Zener diode
Switch operation
position OUT (–)
Blue
(ON)
Hysteresis Note)
Reed switch: 2 mm or less
Solid state switch: 1 mm or less Dimension

Switch operation
position
(OFF)

Note) Hysteresis may fluctuate due to the operating environment.


Contact SMC if hysteresis causes an operational problem.

Connection
To connect a switch unit to a contact protection box, connect the lead wire
from the side of the contact protection box marked SWITCH to the lead
wire coming out of the switch unit. Keep the switch as close as possible to
the contact protection box, with a lead wire length of no more than 1 meter.

12
Series C55

Auto Switches Connections and Examples


Basic Wiring
Solid state 3-wire, NPN Solid state 3-wire, PNP 2-wire 2-wire
(Solid state) Brown
(Reed switch)
Brown
Brown Brown
Load Load
Load Indicator
Main Main Main Protection
circuit of Black circuit of Black circuit of circuit
switch switch switch
Load etc.

Blue Blue Blue Blue

(Power supplies for switch and load are separate.)


Brown Brown Brown
Load Indicator
Main Main Protection
circuit of Black circuit of
circuit
switch switch
etc.
Load Load
Blue Blue Blue

Examples of Connection to PLC (Programmable Logic Controller)


• Sink input specifications • Source input specifications Connect according to the applicable
3-wire, NPN 3-wire, PNP PLC input specifications, as the
Black Input Black Input
connection method will vary depending
on the PLC input specifications.
Brown Brown
Switch Switch
Blue Blue

COM COM
PLC internal circuit PLC internal circuit

2-wire 2-wire
Brown Input Blue Input

Switch Switch

Blue COM Brown COM


PLC internal circuit PLC internal circuit

Connection Examples for AND (Serial) and OR (Parallel)


 3-wire OR connection for NPN output
AND connection for NPN output AND connection for NPN output
(using relays) (performed with switches only)
Brown Brown Brown
Load
Black Black Black
Switch 1 Relay Switch 1 Load Switch 1 Load
Blue Relay Blue Blue
contact
Brown Brown Brown
Black Black Black
Switch 2 Relay Switch 2 Switch 2
Blue Blue Blue
The indicator lights will light up
when both switches are turned ON.

2-wire with 2-switch AND connection 2-wire with 2-switch OR connection

Brown When two switches are (Solid state) (Reed switch)


Brown When two switches Because there is no cu-
Load connected in series, a load Load
may malfunction because are connected in para- rrent leakage, the load
Switch 1 Switch 1
Blue the load voltage will decline Blue llel, a malfunction may voltage will not increase
when in the ON state. occur because the when turned OFF. Ho-
The indicator lights will light load voltage will in- wever, depending on
Brown Brown
Switch 2 up if both of the switches Switch 2 crease when in the the number of switches
are in the ON state. OFF state. in the ON state, the indi-
Blue Blue cator lights may someti-
Load voltage at OFF = Leakage current x 2 pcs. mes dim or not light be-
Power supply Internal cause of the dispersion
Load voltage at ON = – x 2 pcs. x Load impedance
voltage voltage drop and reduction of the cu-
= 24 V - 4 V x 2 pcs. = 1 mA x 2 pcs. x 3 kΩ
rrent flowing to the swit-
= 16 V =6V ches.
Example: Power supply is 24 VDC. Example: Load impedance is 3 kΩ.
Internal voltage drop in switch is 4 V. Leakage current from switch is 1 mA.

13
Reed Switch: Direct Mounting Style
D-A90(V)/D-A93(V)/D-A96(V)
Auto Switch Specifications
Grommet PLC: Programmable Logic Controller
Electrical entry direction: In-line D-A90/D-A90V (without indicator light)
Auto switch model D-A90/D-A90V
Applicable load IC circuit, Relay, PLC
Load voltage 24 V AC/DC or less 48 V AC/DC or less 100 V AC/DC or less
Maximum load current 50 mA 40 mA 20 mA
Contact protection circuit None
Internal resistance 1 Ω or less (including lead wire length of 3 m)
D-A93/D-A93V/D-A96/D-A96V (with indicator light)
Auto switch model D-A93/D-A93V D-A96/D-A96V
Applicable load Relay, PLC IC circuit
Caution Load voltage 24 VDC 100 VAC 4 to 8 VDC
Operating Precautions Load current range
Fix the switch with appropriate screw and max. load 5 to 40 mA 5 to 20 mA 20 mA
current
installed on the switch body. If using other
screws, switch may be damaged. Contact protection circuit None
Internal voltage D-A93 — 2.4 V or less (to 20 mA)/3 V or less (to 40 mA)
drop 0.8 V or less
D-A93V — 2.7 V or less
Indicator light Red LED lights when ON
Lead wires
Auto Switch Internal Circuit D-A90(V)/D-A93(V) — Oilproof vinyl heavy-duty cord: ø2.7, 0.18 mm2 x 2 cores (Brown, Blue), 0.5 m
D-A96(V) — Oilproof vinyl heavy-duty cord: ø2.7, 0.15 mm2 x 3 cores (Brown, Black, Blue), 0.5 m
D-A90(V) Note 1) Refer to page 12 for reed switch common specifications.
Note 2) Refer to page 12 for lead wire lengths.
Contact OUT (±)
Reed switch

protection Brown
box Weight Unit: g
CD-P11
CD-P12 OUT (±)
Blue
Auto switch model D-A90 D-A90V D-A93 D-A93V D-A96 D-A96V
Lead wire length: 0.5 m 6 6 6 6 8 8
D-A93(V) Lead wire length: 3 m 30 30 30 30 41 41
LED diode Brown
Contact OUT (+)
Resistor protection Brown
Dimensions Unit: mm
Reed switch

box
Zener
diode CD-P11
CD-P12 D-A90/D-A93/D-A96
OUT (–) Indicator light
Blue Blue
D-A90 without indicator light
M2.5 x 4 l
Slotted set screw

D-A96(V)
DC (+)
LED diode Brown
(+)
Resistor Most sensitive
Load
Reed switch

Reverse OUT DC power position


current Black supply
prevention
diode diode
(–)
DC (–)
Blue

( ): dimensions for D-A93.


Note) 1. Operating load is an induction load. D-A90V/D-A93V/D-A96V
2. The length of wiring to the load is 5 m or
more.
3. The load voltage is 100 VAC.
Use the contact protection box in any of the
above listed situations.
The contact point life may be shortened. (Refer to
page 12 for contact protection box.)
Most sensitive
position
M2.5 x 4l Slotted set screw

Indicator light
D-A90 without indicator light 14
Solid State Switch: Direct Mounting Style
D-M9N(V)/D-M9P(V)/D-M9B(V)
Auto Switch Specifications
Grommet PLC: Programmable Logic Controller

 2-wire load current is D-M9쏔/D-M9쏔V (with indicator light)


reduced (2.5 to 40 mA) Auto switch model D-M9N D-M9NV D-M9P D-M9PV D-M9B D-M9BV
 Lead-free Electrical entry direction In-line Perpendicular In-line Perpendicular In-line Perpendicular

 Using UL certified (style 2844) Wiring type 3-wire 2-wire


lead wire. Output type NPN PNP —
Applicable load IC circuit, Relay, PLC 24 VDC relay, PLC
Power supply voltage 5, 12, 24 VDC (4.5 to 28 V) —
Current consumption 10 mA or less —
Load voltage 28 VDC or less — 24 VDC (10 to 28 VDC)
Load current 40 mA or less 2.5 to 40 mA
Internal voltage drop 0.8 V or less 4 V or less
Leakage current 100 µA or less at 24 VDC 0.8 mA or less
Indicator light Red LED lights when ON.
Lead wires
Oilproof vinyl heavy-duty cord: ø2.7 x 3.2 ellipse, 0.15 mm2,
D-M9B(V) 0.15 mm2 x 2 cores
D-M9N(V), D-M9P(V) 0.15 mm2 x 3 cores
Note 1) Refer to page 12 for solid state switch common specifications.
Note 2) Refer to page 12 for lead wire lengths.

Caution Weight Unit: g


Operating Precautions
Fix the switch with appropriate screw Auto switch model D-M9N(V) D-M9P(V) D-M9B(V)
installed on the switch body. If using other 0.5 8 8 7
screws, switch may be damaged. Lead wire length
(m) 3 41 41 38
5 68 68 63

Auto Switch Internal Circuit


Dimensions Unit: mm
D-M9N(V)
3.2

DC (+)
Brown D-M9쏔
Main circuit
of switch

OUT 6 Most sensitive position


Black 22 500 (3000)
Mounting screw M2.5 x 4 l
Slotted set screw
DC (–)
Blue Indicator light 2.6

D-M9P(V)
2.7
2.8
4

DC (+)
Brown 22 500 (3000)
Main circuit
of switch

500 (3000) (5000)

OUT
Black D-M9쏔V
DC (–)
Blue
2.7
D-M9B(V)
2.6

OUT (+)
9.5

Brown
Main circuit
of switch

Mounting screw M2.5 x 4 l Indicator light


Slotted set screw 8
2 3.2
4.6

OUT (–)
Blue
4
2.8

6 Most sensitive position


20

15
2-colour Indication Type, Solid State Switch: Direct Mounting Style
D-F9NW(V)/D-F9PW(V)/D-F9BW(V)
Auto Switch Specifications
Grommet PLC: Programmable Logic Controller
D-F9쏔W/D-F9쏔WV (with indicator light)
Auto switch model D-F9NW D-F9NWV D-F9PW D-F9PWV D-F9BW D-F9BWV
Electrical entry direction In-line Perpendicular In-line Perpendicular In-line Perpendicular
Wiring type 3-wire 2-wire
Output type NPN PNP –
Applicable load IC circuit, Relay, PLC 24 VDC relay, PLC
Power supply voltage 5, 12, 24 VDC (4.5 to 28 VDC) –
Current consumption 10 mA or less –
Load voltage 28 VDC or less – 24 VDC (10 to 28 VDC)
Caution Load current 40 mA or less 80 mA or less 5 to 40 mA
Operating Precautions 1.5 V or less
Internal voltage
(0.8 V or less at 10 mA 0.8 V or less 4 V or less
drop
Fix the switch with appropriate screw load current)
installed on the switch body. If using other Leakage current 100 µA or less at 24 VDC 0.8 mA or less
screws, switch may be damaged.
Operating position .......... Red LED lights when ON.
Indicator light
Optimum operating position .......... Green LED lights when ON.
Auto Switch Internal Circuit Lead wires
Oilproof vinyl heavy-duty cord: ø2.7, 0.15 mm2 x 3 cores (Brown, Black, Blue),
D-F9NW(V) 0.18 mm2 x 2 cores (Brown, Blue), 0.5 m
Note 1) Refer to page 12 for solid state switch common specifications.
DC (+) Note 2) Refer to page 12 for lead wire lengths.
Brown
Main circuit

OUT
of switch

Black
Weight Unit: g

DC (–)
Blue Auto switch model D-F9NW(V) D-F9PW(V) D-F9BW(V)
0.5 7 7 7
Lead wire length
3 34 34 32
(m)
D-F9PW(V) 5 56 56 52
DC (+)
Brown
Main circuit

Dimensions
of switch

Unit: mm
OUT
Black
D-F9첸W
2.6

4
DC (–)
Blue
6 Most sensitive position

Mounting screw M2.5 x 4 l


Slotted set screw
D-F9BW(V)
Indicator light
ø2.7

2
OUT (+)
Brown
Main circuit
of switch

22
2.8

ø2.7

OUT (–) D-F9첸WV


3.8

Blue

Indicator light/Display method


6.2

4
3.1

ON 6 Most sensitive position


Operating Mounting screw M2.5 x 4 l
range OFF
Slotted set screw
4.3
Indication Indicator light
2
Red Green Red

Optimum operating
position
20
2.8
4.6

16
Water Resistant 2-colour Indication Type
Solid State Switch: Direct Mounting Style
D-M9BAL
Auto Switch Specifications
Grommet PLC: Programable Logic Controller
D-M9BAL (with indicator light)
Water (coolant) resistant type Auto switch model D-M9BAL
Wiring type 2-wire
Output type —
Applicable load 24 VDC relay, PLC
Power supply voltage —
Current consumption —
Load voltage 24 VDC (10 to 28 VDC)
Load current 5 to 30 mA
Internal voltage drop 5 V or less
Leakage current 1 mA or less at 24 VDC

Caution Indicator light Operating position ..... Red LED lights when ON.
Optimum operating position ..... Green LED lights when ON.
Operating Precautions
 Lead wires
1. Please consult with SMC if using coolant Oilproof vinyl heavy-duty cord: ø2.7, 2 cores (Brown, Blue), 0.18 mm2, 0.5 m
liquid other than water based solution. Note 1) Refer to page 12 for solid state switch common specifications.
2. Fix the switch with appropriate screw ins- Note 2) Refer to page 12 for lead wire lengths.
talled on the switch body. If using other
screws, switch may be damaged.

Weight Unit: g

Auto Switch Model D-M9BA


0.5 —
Lead wire length
(m) 3 37
Auto Switch Internal Circuit 5 57

OUT (+)
Brown
Main circuit

Dimensions Unit: mm
of switch

OUT (-)
Blue

Indicator light/Display method

ON Most sensitive position


Operating
range OFF
Indica-
tion M2.5 x 4
Red Green Red Slotted set screw
ø2.7

Optimum operating position Indicator light

17
18
EUROPEAN SUBSIDIARIES:

Austria France Netherlands Spain


SMC Pneumatik GmbH (Austria). SMC Pneumatique, S.A. SMC Pneumatics BV SMC España, S.A.
Girakstrasse 8, A-2100 Korneuburg 1, Boulevard de Strasbourg, Parc Gustave Eiffel De Ruyterkade 120, NL-1011 AB Amsterdam Zuazobidea 14, 01015 Vitoria
Phone: +43 2262-62280, Fax: +43 2262-62285 Bussy Saint Georges F-77607 Marne La Vallee Cedex 3 Phone: +31 (0)20-5318888, Fax: +31 (0)20-5318880 Phone: +34 945-184 100, Fax: +34 945-184 124
E-mail: office@smc.at Phone: +33 (0)1-6476 1000, Fax: +33 (0)1-6476 1010 E-mail: info@smcpneumatics.nl E-mail: post@smc.smces.es
http://www.smc.at E-mail: contact@smc-france.fr http://www.smcpneumatics.nl http://www.smces.es
http://www.smc-france.fr

Belgium Germany Norway Sweden


SMC Pneumatics N.V./S.A. SMC Pneumatik GmbH SMC Pneumatics Norway A/S SMC Pneumatics Sweden AB
Nijverheidsstraat 20, B-2160 Wommelgem Boschring 13-15, D-63329 Egelsbach Vollsveien 13 C, Granfos Næringspark N-1366 Lysaker Ekhagsvägen 29-31, S-141 71 Huddinge
Phone: +32 (0)3-355-1464, Fax: +32 (0)3-355-1466 Phone: +49 (0)6103-4020, Fax: +49 (0)6103-402139 Tel: +47 67 12 90 20, Fax: +47 67 12 90 21 Phone: +46 (0)8-603 12 00, Fax: +46 (0)8-603 12 90
E-mail: post@smcpneumatics.be E-mail: info@smc-pneumatik.de E-mail: post@smc-norge.no E-mail: post@smcpneumatics.se
http://www.smcpneumatics.be http://www.smc-pneumatik.de http://www.smc-norge.no http://www.smc.nu

Bulgaria Greece Poland Switzerland


SMC Industrial Automation Bulgaria EOOD S. Parianopoulus S.A. SMC Industrial Automation Polska Sp.z.o.o. SMC Pneumatik AG
16 kliment Ohridski Blvd., fl.13 BG-1517 Sofia 7, Konstantinoupoleos Street, GR-11855 Athens ul. Konstruktorska 11A, PL-02-673 Warszawa, Dorfstrasse 7, CH-8484 Weisslingen
Phone:+359 2 9744492, Fax:+359 2 9744519 Phone: +30 (0)1-3426076, Fax: +30 (0)1-3455578 Phone: +48 22 548 5085, Fax: +48 22 548 5087 Phone: +41 (0)52-396-3131, Fax: +41 (0)52-396-3191
E-mail: office@smc.bg E-mail: parianos@hol.gr E-mail: office@smc.pl E-mail: info@smc.ch
http://www.smc.bg http://www.smceu.com http://www.smc.pl http://www.smc.ch

Croatia Hungary Portugal Turkey


SMC Industrijska automatika d.o.o. SMC Hungary Ipari Automatizálási Kft. SMC Sucursal Portugal, S.A. Entek Pnömatik San. ve Tic Ltd. Sti.
Crnomerec 12, 10000 ZAGREB Budafoki ut 107-113, H-1117 Budapest Rua de Engº Ferreira Dias 452, 4100-246 Porto Perpa Tic. Merkezi Kat: 11 No: 1625, TR-80270 Okmeydani Istanbul
Phone: +385 1 377 66 74, Fax: +385 1 377 66 74 Phone: +36 1 371 1343, Fax: +36 1 371 1344 Phone: +351 22-610-89-22, Fax: +351 22-610-89-36 Phone: +90 (0)212-221-1512, Fax: +90 (0)212-221-1519
E-mail: office@smc.hr E-mail: office@smc-automation.hu E-mail: postpt@smc.smces.es E-mail: smc-entek@entek.com.tr
http://www.smceu.com http://www.smc-automation.hu http://www.smces.es http://www.entek.com.tr

© DiskArt™ 1988

Czech Republic Ireland Romania © DiskArt™

UK
SMC Industrial Automation CZ s.r.o. SMC Pneumatics (Ireland) Ltd. SMC Romania srl SMC Pneumatics (UK) Ltd
Hudcova 78a, CZ-61200 Brno 2002 Citywest Business Campus, Naas Road, Saggart, Co. Dublin Str Frunzei 29, Sector 2, Bucharest Vincent Avenue, Crownhill, Milton Keynes, MK8 0AN
Phone: +420 5 414 24611, Fax: +420 5 412 18034 Phone: +353 (0)1-403 9000, Fax: +353 (0)1-464-0500 Phone: +40 213205111, Fax: +40 213261489 Phone: +44 (0)800 1382930 Fax: +44 (0)1908-555064
E-mail: office@smc.cz E-mail: sales@smcpneumatics.ie E-mail: smccadm@canad.ro E-mail: sales@smcpneumatics.co.uk
http://www.smc.cz http://www.smcpneumatics.ie http://www.smcromania.ro http://www.smcpneumatics.co.uk

Denmark Italy Russia


SMC Pneumatik A/S SMC Italia S.p.A SMC Pneumatik LLC.
Knudsminde 4B, DK-8300 Odder Via Garibaldi 62, I-20061Carugate, (Milano) 36/40 Sredny pr. St. Petersburg 199004
Phone: +45 70252900, Fax: +45 70252901 Phone: +39 (0)2-92711, Fax: +39 (0)2-9271365 Phone.:+812 118 5445, Fax:+812 118 5449
E-mail: smc@smc-pneumatik.dk E-mail: mailbox@smcitalia.it E-mail: smcfa@peterlink.ru
http://www.smcdk.com http://www.smcitalia.it http://www.smc-pneumatik.ru

Estonia Latvia Slovakia


SMC Pneumatics Estonia OÜ SMC Pneumatics Latvia SIA SMC Priemyselná Automatizáciá, s.r.o.
Laki 12-101, 106 21 Tallinn Smerla 1-705, Riga LV-1006, Latvia Námestie Martina Benku 10, SK-81107 Bratislava
Phone: +372 (0)6 593540, Fax: +372 (0)6 593541 Phone: +371 (0)777-94-74, Fax: +371 (0)777-94-75 Phone: +421 2 444 56725, Fax: +421 2 444 56028
E-mail: smc@smcpneumatics.ee E-mail: info@smclv.lv E-mail: office@smc.sk
http://www.smcpneumatics.ee http://www.smclv.lv http://www.smc.sk

Finland Lithuania Slovenia


SMC Pneumatics Finland OY UAB Ottensten Lietuva SMC industrijska Avtomatika d.o.o.
PL72, Tiistinniityntie 4, SF-02031 ESPOO Savanoriu pr. 180, LT-2600 Vilnius, Lithuania Grajski trg 15, SLO-8360 Zuzemberk
Phone: +358 (0)9-859 580, Fax: +358 (0)9-8595 8595 Phone: +386 738 85240 Fax: +386 738 85249
E-mail: smcfi@smc.fi Phone/Fax: +370-2651602
E-mail: office@smc-ind-avtom.si
http://www.smc.fi http://www.smc-ind-avtom.si

OTHER SUBSIDIARIES WORLDWIDE:


ARGENTINA, AUSTRALIA, BOLIVIA, BRASIL, CANADA, CHILE,
CHINA, HONG KONG, INDIA, INDONESIA, MALAYSIA, MEXICO,
NEW ZEALAND, PHILIPPINES, SINGAPORE, SOUTH KOREA,
TAIWAN, THAILAND, USA, VENEZUELA

http://www.smceu.com
http://www.smcworld.com
SMC CORPORATION 1-16-4 Shimbashi, Minato-ku, Tokio 105 JAPAN; Phone:03-3502-2740 Fax:03-3508-2480
Produced and printed by SMC European Marketing Centre 12/04 Specifications are subject to change without prior notice
and any obligation on the part of the manufacturer.

You might also like