Atlas Specialty Metals, a division of Atlas Steels (Australia) Pty Ltd ABN 13 004 496 128

ATLAS SPECIALTY METALS

CARBON STEEL HOLLOW BAR

Specifications
Atlas Carbon Steel Hollow Bar is in accordance with EN DIN 1629/1630 and EN DIN 2448.

Chemical Composition
Atlas Carbon Steel Hollow Bar is supplied in two grades. Grade 20MnVS6 (WNr 1.5217) for sizes 32-
250mm and Grade St 52.0 (WNr 1.0421) for all sizes 250-457 mm.

C Si Mn P S V
20MnVS6 0.16-0.22 0.10-0.50 1.30-1.70 0.035 max 0.020-0.035 0.10-0.201)
St 52.0 0.22 max. 0.10-0.55 1.20-1.60 0.035 max 0.020-0.035
1) in addition steel may contain Nb, whereby V+Nb = max. 0.21% applies

20MnVS6 is a micro-alloy steel with improved mechanical properties and with controlled sulphur
content to improve machinability. St52.0 is a plain carbon steel defined by its mechanical properties;
again controlled sulphur addition improves machinability.

Mechanical Properties
Tensile Strength Yield Strength Elongation Impact Value
Rm in MPa ReH in MPa min. A in % min. ISO-V (long)
Delivery for wall thickness in mm for wall thickness in mm min.
Grade
Condtion
12- 25- 40- 50-
<25 25-50 50-80 <12 long transv Test T J min
25 40 50 65
650- 620-
Untreated 470 470 450 430 17 15 0°C 27
800 770
20MnVS6
700- 650- 520-
Q&T 590 570 540 510 480 16 14 -40°C 27
850 800 670
16- 40-
<16 16-40 40-65 <16
40 65
St52.0 Untreated 490-630 355 345 335 17 15 0°C 27

Heat Treatment
20MnVS6 is suitable for normalising, stress relief and hardening (Q&T). 20MnVS6 can be case
hardened (or carbonitrided) to give a case depth of up to 1mm and hardness of up to 60 HRC. For
further details consult a heat treatment specialist.

St 52.0 is suitable for normalising and stress relieving. For further details consult a heat treatment
specialist.

Weldability
20MnVS6 hollow bar can be readily welded using all conventional methods. Welds should be
completed without interruption. For fillet welds, a multi-pass technique should be selected. Stress
relieving is generally not necessary. In case of WT>12mm preheating to 150-200°C is recommended.
St52.0 hollow bar can be readily welded using manual and automatic methods. Preheating and/or
stress relieving are generally not required, though may be necessary in the case of WT >30mm. For
20MnVS6 and St52.0 basic welding consumables are recommended.

For information on welding at low temperatures and other special conditions please consult your local
welding specialist or Technical Support of Atlas Specialty Metals.

Atlas Technical Support: Email: tech@atlasmetals.com.au Toll Free: 1800 818 599 Fax: 03 9272 9966
 Clean turned Clean turned Clean turned Clean turned
Nominal Ave. sizes sizes Nominal Ave. sizes sizes
sizes Weight OD centered ID centered sizes Weight OD centered ID centered
OD ID OD ID OD ID OD ID OD ID OD ID
mm mm kg/m mm mm mm mm mm mm kg/m mm mm mm mm
32 20 4.2 31.5 21.9 30.5 21.4 132 106 41.3 130.9 108.8 128.9 107.8
32 16 5.0 31.5 18.2 30.2 17.4 132 98 51.8 130.9 100.6 128.8 99.6
36 25 4.5 35.6 26.9 34.5 26.4 132 90 60.2 130.9 93.0 128.7 91.9
36 20 5.9 35.6 22.3 34.1 21.5 132 80 70.6 130.9 83.6 128.1 82.3
36 16 6.7 35.6 18.6 33.9 17.4 132 71 78.8 130.9 74.9 127.7 73.4
40 28 5.5 39.6 30.0 38.5 29.5 140 112 47.5 138.9 114.8 136.9 113.8
40 25 6.4 39.6 27.2 38.3 26.6 140 106 55.8 138.9 109.0 136.8 108
40 20 7.8 39.6 23.7 38.1 21.6 140 100 62.8 138.9 103.5 136.7 102.4
45 32 6.7 44.6 34.0 43.5 33.5 140 90 74.4 138.9 93.7 136.3 92.4
45 28 8.1 44.6 30.2 43.5 33.5 140 80 84.7 138.9 84.0 135.9 82.4
45 20 10.4 44.6 23.9 43.1 21.7 150 125 47.2 149 127.6 147.2 126.7
50 36 8.2 49.9 38.2 48.6 37.6 150 118 57.3 149 121.2 146.8 102.1
50 32 9.9 49.9 34.3 48.6 33.7 150 106 73.6 149 109.4 146.6 108.2
50 25 12.3 49.9 27.8 48.1 27 150 95 87.1 149 98.6 146.4 97.1
56 40 10.4 55.9 42.3 54.6 41.7 150 80 103.0 149.3 83.9 146.4 81
56 36 12.2 55.9 38.5 54.4 38.7 160 132 56.5 159.1 134.6 157.1 133.8
56 28 15.3 55.9 30.9 54 30 160 122 71.0 159.1 124.6 157 123.6
63 50 9.9 62.4 52.0 61 51.4 160 112 85.3 159.1 115.6 156.4 114.4
63 45 12.8 62.4 47.2 60.9 46.5 160 100 101.0 159.1 104.4 155.8 102.8
63 40 15.3 62.4 41.4 60.7 40.6 160 90 112.0 159.1 94.2 155.9 91
63 36 17.2 62.4 38.6 60.5 37.7 162 111 85.6 160 115.0 157.5 114.4
63 32 18.8 62.4 34.7 60.4 33.8 162 79 122.8 160 85.0 155.9 94
71 50 16.6 70.3 52.6 68.6 51.8 170 140 64.2 169.1 142.9 167 142
71 45 19.5 70.3 47.9 68.4 47 170 130 79.6 169.1 133.0 166.9 132.1
71 40 22.1 70.3 43.0 68.5 42 170 118 97.8 169.1 121.8 166.3 120.6
71 36 24.0 70.3 39.1 68.4 38 170 100 122.0 169.2 104.4 166 101.2
75 56 16.7 74.7 58.5 73.1 57.5 180 150 68.7 179.2 152.9 177.1 152
75 50 20.5 74.7 53.0 72.9 52.1 180 140 85.3 179.2 142.9 177 142.1
75 45 23.6 74.7 48.2 72.8 47.2 180 125 109.9 179.2 128.9 176.2 127.6
75 40 26.2 74.7 43.2 72.7 42.2 180 100 144.0 179.3 104.5 175.8 101
80 63 16.2 79.4 65.4 77.9 64.7 190 160 73.7 189.4 164.0 187.4 162
80 56 21.3 79.4 58.7 77.6 57.8 190 150 90.7 189.4 154.7 187.2 152
80 50 25.2 79.4 52.9 77.4 51.9 190 132 122.0 189.4 136.6 186.5 133.7
80 45 28.3 79.4 47.9 77.4 46.9 190 118 143.0 189.4 122.6 186.2 119.4
80 40 30.7 79.4 42.9 77.3 41.9 190 106 160.0 189.4 110.3 186.1 107
85 67 18.2 84.5 69.5 83 68.8 200 160 96.9 198 164.4 195.6 162
85 55 27.2 84.5 58.0 82.5 57 200 140 133.0 198 144.9 195.1 142
85 45 33.3 84.5 48.0 82 47 200 112 176.0 198 116.9 194.6 113.7
90 71 20.5 89.3 73.4 87.7 72.6 212 170 108.0 210 174.9 207.6 172.5
90 67 23.8 89.3 69.5 87.7 68.7 212 150 146.6 210 154.9 207.1 152
90 63 27.0 89.3 65.8 87.7 64.8 212 125 189.0 210 130.2 206.6 126.7
90 56 32.0 89.3 59.3 87.7 58.3 224 180 119.0 222.3 184.9 219.9 182.5
90 50 35.8 89.3 53.0 87.7 52 224 160 160.7 222.3 165.6 219.3 162.5
95 75 22.9 94.4 77.5 92.7 76.7 224 132 210.2 221 138.8 216.2 134
95 67 29.6 94.4 70.0 92.4 69 236 190 132.0 232 196.5 228.5 193
95 56 37.9 94.4 59.0 92.1 58 236 170 176.0 232 176.9 228.1 173
95 50 41.7 94.4 53.5 91.9 53.3 236 140 231.9 232 150.2 224.8 143
100 80 25.0 100 82.5 98.2 81.6 250 200 152.5 246 208 241 203
100 75 29.7 100 77.7 98.1 76.8 250 180 197.5 246 189 240 183
100 71 33.3 100 73.8 98 72.8 250 150 257.1 246 161 238 153
100 63 39.9 99.9 66.0 97.6 65 273 223 153.0 269 232 265 227
100 56 44.7 99.9 59.2 97.4 58 273 213 180.0 269 223 264 218
106 85 27.1 105.5 87.4 103.8 86.6 273 201 210.0 269 212 263 206
106 80 32.0 105.5 82.7 103.5 81.8 273 193 230.0 269 205 263 198
106 71 40.6 105.3 73.8 103.2 72.8 273 173 275.0 269 187 261 179
106 63 46.8 105.3 66.0 103.1 64.9 298 258 137.0 294 266 291 262
106 56 51.7 105.3 59.3 103 58 298 238 199.0 294 248 289 243
112 90 29.9 111.3 92.4 109.6 91.6 298 218 255.0 294 230 288 223
112 80 40.3 111.3 82.7 109.3 81.7 298 198 306.0 294 212 286 204
112 71 48.4 111.3 74.1 109.1 73 324 274 184.0 319 283 316 279
112 63 54.9 111.3 66.2 108.9 65 324 244 280.0 319 256 313 249
118 90 38.5 117.2 93.0 115.1 92 324 224 338.0 319 238 312 230
118 80 48.9 117.2 83.1 114.5 82.1 356 306 204.0 351 315 347 311
118 71 57.2 117.2 74.2 114.4 73 356 276 311.0 351 288 345 282
118 63 63.7 117.2 66.3 114.3 64.9 356 256 377.0 351 270 343 262
125 100 37.8 124.3 102.9 122.4 102 356 236 438.0 351 252 342 243
125 95 43.8 124.3 97.9 122.3 96.9 406 306 439.0 400 320 393 312
125 90 49.8 124.3 92.9 122.2 91.9 406 286 512.0 400 302 391 293
125 80 59.6 124.3 83.3 121.9 82.1 419 319 455.0 413 333 406 325
125 71 67.9 124.3 74.7 121.6 73.3

Figures based on EN DIN 1629/1630 and EN DIN 2248 and mill information. Clean turned sizes 250mm and over indicative
figures only. Clean turned sizes are valid for parts with length up to 120mm. Due to out-of-straightness tolerance for longer
parts 2mm/1000mm has to be deducted from OD figures and added to ID figures.
Atlas Technical Support: Email: tech@atlasmetals.com.au Toll Free: 1800 818 599 Fax: 03 9272 9966