Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 143 views

    6-44-0056 Rev 2 PDF

    Uploaded by

    Mohammed Tariq

    Copyright:

    © All Rights Reserved
    Download as PDF or read online from Scribd

    6-44-0056 Rev 2 PDF

    Uploaded by

    Mohammed Tariq
    143 views3 pages

    Original Title

    6-44-0056 Rev 2.pdf

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    Copyright:

    © All Rights Reserved
    Download as PDF or read online from Scribd
    Download as pdf
    143 views3 pages

    6-44-0056 Rev 2 PDF

    Uploaded by

    Mohammed Tariq

    Copyright:

    © All Rights Reserved
    Download as PDF or read online from Scribd
    Download as pdf
    of 3
    | Wades & fer cede femforat orgie TECHNICAL NOTES FOR GASKETS PIPING JINEERS INDIA LIMITED. They are maraly loaned on the borrower's expross agreement that they wil not be reproduced, ‘way permitted by a written consant given by the lander to the borrower for the intended use. EiL 1641-1251 Rov.2. Ad-210x297. rmnat are the prope 22 | 2 |15:05.00] REAFFIRMED & ISSUED AS STANDARD Fs oe, 3 SPECIFICATION 51 O06 §-¥ [77 Jooro.2|Reviseo « 1ssUED AS STANDARD SPECICATION | Ake ov ORR 7% 28 [no.| pate REVISION BY CHECKED | CONVENOR | CHAIRMAN (6 8.) TECHNICAL NOTES SPECIFICATION REV ENGINEERS INDIA LIMITED FOR GASKETS. 0056 Page 1 of 3 jot be reproduced | OFENGINEERS INDIA LIMITED. They are merely loaned on the borrower” lon ion consent gi TECHNICAL NOTES FOR GASKETS The process of manufacture, dimensions and tolerances not specified in requisition shall be in accordance with the requirements of the manufacturer's standards. All gaskets shall conform to the codes/standards and specifications given in the requisition. Deviation(s), if any, shall be clearly highlighted in the quotation. a. Test reports shall be supplied for all mandatory tests for CAF gaskets as per the standards specified in the requisition. b. Chemical composition of RTI gaskets shall also be furnished in the form of test reports on samples. Full face gaskets shall have bolt holes punched out. Manufacturer's test certificate for filler material and spiral material shall be given as per the relevant material specifications for spiral wound gaskets. Asbestos filler for spiral wound gaskets shall not have any colour or dye. a. All spiral wound gaskets shall be supplied with C.S. outer centring ring except for gasket material description suffixed as “(540+)” or “(CRYO)”. In these cases outer-centring ring shall be of SS 304/316. b. Inner compression ring of S.S. shall be provided for the following, unless mentioned otherwise. (i) For gasket sizes 26” and above (ii) For gasket rating 900# and above. (iii) For gasket material description suffixed as “(425+)” or “(CRYO)” or “(540+)”. Hardness of metallic RTJ gaskets shall not exceed the values specified below: Ring Gasket Material Maximum Hardness (BHN) Soft Iron 90 Low C.S. 120 TECHNICAL NOTES SPECIFICATION | REV ENGINEERS INDIA LIMITED NEW DELHI ene hetele 6-44-0056 2 Page 2 of 3 ‘eemnont that they will hot be reproduced] (0«297, 2 intanded use, EIL 1641-507, A4: loaned on the borrower’ express ited by a written consent given by the lender i Format are the property of ENGINEERS INDIA LIMITED. They way 10. LL. 12. Ring Gasket Material Maximum Hardness (BHN) 5 Cr. % Mo 130 Type 304, 316, 347 140 Type 304L, 316L. 120 Face finish of metallic RTJ gaskets shall be 32 to 63 AARH. Gaskets of different types and sizes shall be placed in separate shipping containers and each container clearly marked with the size, rating, material specification and item code. All items shall be inspected and approved by EIL Inspector or any other agency authorised by EIL. Any additional requirements specified in the requisition, shall be fully complied with. Notes : Non-metallic ring gaskets as per ANSI B16.21 shall match flanges to ANSI B16.5 upto 24” and flanges to API 605 above 24” unless specifically asked for otherwise. Spiral wound gasket as per API 601 shall match flanges to ANSI B16.5 upto 24” and flanges to API 605 above 24” unless specifically asked for otherwise. ENGINEERS INDIA LIMITED TECHNICAL NOTES SPECIFICATION REV NEW DELHI one 6-44-0056 Page 3 of 3|

    You might also like