Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 461 views

    3116 Cat Valvuklas Calibre PDF

    Uploaded by

    sergio blandon l

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    3116 Cat Valvuklas Calibre PDF

    Uploaded by

    sergio blandon l
    461 views4 pages

    Original Title

    3116 cat valvuklas calibre.pdf

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    461 views4 pages

    3116 Cat Valvuklas Calibre PDF

    Uploaded by

    sergio blandon l

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 4
    At a glance
    Powered by AI
    The document discusses inspecting and adjusting valve lash on a 3116 truck engine, including checking measurement ranges and adjustment procedures.

    To inspect valve lash, the measurement is taken with the engine stopped and valves fully closed. An adjustment is only necessary if the measurement is outside the acceptable range provided in Table 1. The adjustment procedure is outlined in the Valve Lash Adjustment section.

    Table 1 provides the acceptable valve lash measurement ranges for inlet and exhaust valves with the engine stopped. The inlet range is 0.30 to 0.46 mm and the exhaust range is 0.56 to 0.72 mm.

    3116 Truck Engine 7HS00001-UP(SEBP2721 - 20) - Systems & Components Página 1 de 4

    Previous Screen

    Welcome: r462jgu

    Product: TRUCK ENGINE


    Model: 3116 TRUCK ENGINE 7HS
    Configuration: 3116 Truck Engine 7HS00001-UP

    Testing and Adjusting


    3116 Truck Engine
    Media Number -SENR5118-05 Publication Date -01/10/2001 Date Updated -15/11/2001

    i01615445

    Engine Valve Lash - Inspect/Adjust


    SMCS - 1102-025

    To prevent possible injury, do not use the starter to turn the flywheel.

    Hot engine components can cause burns. Allow additional time for the
    engine to cool before measuring valve clearance.

    Note: Valve lash is measured between the rocker arm and the valve. All measurements and
    adjustments must be made with the engine stopped and the valves FULLY CLOSED.

    Valve Lash Check


    An adjustment is NOT NECESSARY if the measurement of the valve lash is in the acceptable
    range in Table 1.

    Table 1
    Valve Lash Check (Stopped Engine)

    Inlet
    0.30 to 0.46 mm (0.012 to 0.018 inch)

    Exhaust
    0.56 to 0.72 mm (0.022 to 0.028 inch)

    If the measurement is not within this range, an adjustment is necessary. Refer to "Valve Lash
    Adjustment" for the proper procedure.

    https://sisweb.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 25/09/2015
    3116 Truck Engine 7HS00001-UP(SEBP2721 - 20) - Systems & Components Página 2 de 4

    Valve Lash Adjustment


    Table 2
    Valve Lash Setting (Stopped Engine)
    Inlet
    0.38 mm (0.015 inch)
    Exhaust
    0.64 mm (0.025 inch)

    Illustration 1 g00821000

    Cylinder and valve location

    (A) Exhaust valves

    (B) Inlet valves

    Use the following procedure to adjust the valve lash:

    https://sisweb.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 25/09/2015
    3116 Truck Engine 7HS00001-UP(SEBP2721 - 20) - Systems & Components Página 3 de 4

    Illustration 2 g00708315

    Valve adjustment (typical example)

    (1) Valve

    (2) Rocker arm

    (3) Adjustment locknut

    (4) Adjustment screw

    1. Put the No. 1 piston at the top center position on the compression stroke. Refer to Testing
    and Adjusting, "Finding Top Center Position for No. 1 Piston".

    2. With the No. 1 piston at the top center position of the compression stroke, an adjustment can
    be made to the valves. Refer to Testing and Adjusting, "Gear rG oup (Front) - Time" for the
    information that is required in order to adjust the valves.

    Note: Before any actual adjustment is made, lightly tap the rocker arm at the top of the
    adjustment screw with a soft mallet. This will ensure that the lifter roller seats against the
    camshaft's base circle.

    3. Loosen adjustment locknut (3) .

    4. If there is not enough clearance in order to insert the feeler gauge between rocker arm (2)
    and valve (1), turn adjustment screw (4) counterclockwise in order to increase the clearance.

    5. Place the appropriate feeler gauge between rocker arm (2) and the valve (1). Then, turn the
    adjustment screw in a clockwise direction. Slide the feeler gauge between the rocker arm
    and the valve. Continue turning the adjustment screw until a slight drag is felt on the feeler
    gauge. Remove the feeler gauge.

    6. Tighten adjustment locknut (3) to a torque of 30 ± 7 N·m (22 ± 5 lb ft). Do not allow the
    adjustment screw to turn while you are tightening the adjustment locknut. Recheck the valve
    lash after tightening the adjustment locknut.

    https://sisweb.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 25/09/2015
    3116 Truck Engine 7HS00001-UP(SEBP2721 - 20) - Systems & Components Página 4 de 4

    7. Remove the timing bolt and turn the flywheel by 360 degrees in the direction of engine
    rotation. This will put the No. 6 piston at the top center position on the compression stroke.
    Install the timing bolt in the flywheel.

    8. Adjust the valve lash on the remaining valves. Refer to Testing and Adjusting, "Gear rG oup
    (Front) - Time" for the information that is required in order to adjust the valves.

    9. Repeat Step 3 through Step 6 for these valve adjustments.

    10. Remove the timing bolt from the flywheel after all adjustments to the valve lash have been
    made. Reinstall the timing cover.

    Refer to Testing and Adjusting, "Unit Injector - Adjust".

    Copyright 1993 - 2015 Caterpillar Inc. Fri Sep 25 09:45:54 EST 2015
    All Rights Reserved. r462jgu
    Private Network For SIS Licensees.

    https://sisweb.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 25/09/2015

    You might also like