JOB CARD MPD-TASK:

CEB - A318/A319/A320/A321 AMM TASK : 78-11-11-000-041-A

78-11-11 PB 401

TITLE:
A/C Reg.:
78-11-11-000-041-A - Removal
RP-C3244
of the Core Nozzle Assembly
CARD: ZONE: INTERVAL:
SKILL: ACCESS: 437AL, 438AR, 451AL, 452AR, 447AL, 448AR, 461AL, 462AR

MECH. INSP.

** ON A/C 103-159, 161-250

TASK 78-11-11-000-041-A
Removal of the Core Nozzle Assembly

FIN : 1000EM1 , 1000EM2

1. Reason for the Job
Self explanatory
2 Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE QTYDESIGNATION
No specific AR ACCESS PLATFORM 1M(3 FT)
No specific AR WARNING NOTICE(S)

B. Work Zones and Access Panels

ZONE/ACCESS ZONE DESCRIPTION

FOR 1000EM1 (ENGINE-1)
437AL, 438AR, 451AL,
452AR
FOR 1000EM2 (ENGINE-2)
447AL, 448AR, 461AL,
462AR

C. Referenced Information

REFERENCE DESIGNATION
(Ref. 71-13-00-010-040-B). Opening of the Fan Cowl Doors
(Ref. 71-73-49-000-005-B). Removal of the Turbine Rear Frame TRF Drain Tube
(Ref. 78-30-00-481-041-B). Make the Thrust Reverser Unserviceable for
Maintenance
(Ref. 78-36-00-010-040-B). Opening of the Thrust Reverser Doors

** ON A/C 103-159, 161-200

Core Nozzle Assembly SHEET 1
Parts That Attach The Core Nozzle Assembly SHEET 1

JCP Title: RP-C3244 C08 + HMA + HMB + W&B + CERTIFICATE OF TASK / INSPECTION COMPLETION: Page 1 of 5
LEASE RETURN DATABASE REV DATE: Aug 01/2019
JCP Ref: Service Order No.S4875119 CERTIFIES THAT THE TASK / INSPECTION HAS BEEN COMPLETED TO THE REQUIRED PRINT DATE: Sep 17/2019 12:18
STANDARD AND SUPPORTS THE FINAL MAINTENANCE RELEASE / CERTIFICATE OF RELEASE
TO SERVICE
 JOB CARD MPD-TASK:
CEB - A318/A319/A320/A321 AMM TASK : 78-11-11-000-041-A
78-11-11 PB 401

TITLE:
A/C Reg.:
78-11-11-000-041-A - Removal
RP-C3244
of the Core Nozzle Assembly
MECH. INSP.

A A

FLANGE
STA 258 (A6)

FLANGE
CUTOUT

25 x88
10 x88
30 x88

15

DRAIN
FITTING
FLANGE
STA 252
C1M-311-03

20

N_MM_781111_4_RAN0_01_01

Figure 78(CFMB)-11-11-991-30100-06-B / SHEET 1/1 - Core Nozzle Assembly

** ON A/C 103-159, 161-200

JCP Title: RP-C3244 C08 + HMA + HMB + W&B + CERTIFICATE OF TASK / INSPECTION COMPLETION: Page 2 of 5
LEASE RETURN DATABASE REV DATE: Aug 01/2019
JCP Ref: Service Order No.S4875119 CERTIFIES THAT THE TASK / INSPECTION HAS BEEN COMPLETED TO THE REQUIRED PRINT DATE: Sep 17/2019 12:18
STANDARD AND SUPPORTS THE FINAL MAINTENANCE RELEASE / CERTIFICATE OF RELEASE
TO SERVICE
 JOB CARD MPD-TASK:
CEB - A318/A319/A320/A321 AMM TASK : 78-11-11-000-041-A
78-11-11 PB 401

TITLE:
A/C Reg.:
78-11-11-000-041-A - Removal
RP-C3244
of the Core Nozzle Assembly
MECH. INSP.

FLANGE
STA 258 (A6)
VIEW LOOKING
FWD

30

10
25
C1M-310-01

ENGINE FLANGE NOZZLE ASSEMBLY

TYPICAL 88 LOCATIONS

N_MM_781111_4_RBN0_01_01

Figure 78(CFMB)-11-11-991-30200-06-B / SHEET 1/

1 - Parts That Attach The Core Nozzle Assembly
** ON A/C 103-159, 161-250

JCP Title: RP-C3244 C08 + HMA + HMB + W&B + CERTIFICATE OF TASK / INSPECTION COMPLETION: Page 3 of 5
LEASE RETURN DATABASE REV DATE: Aug 01/2019
JCP Ref: Service Order No.S4875119 CERTIFIES THAT THE TASK / INSPECTION HAS BEEN COMPLETED TO THE REQUIRED PRINT DATE: Sep 17/2019 12:18
STANDARD AND SUPPORTS THE FINAL MAINTENANCE RELEASE / CERTIFICATE OF RELEASE
TO SERVICE
 JOB CARD MPD-TASK:
CEB - A318/A319/A320/A321 AMM TASK : 78-11-11-000-041-A
78-11-11 PB 401

TITLE:
A/C Reg.:
78-11-11-000-041-A - Removal
RP-C3244
of the Core Nozzle Assembly
MECH. INSP.

3. Job Set-up
Subtask 78-11-11-941-051-A
A. Safety Precautions
(1) On the center pedestal, on the ENG panel 115VU:
(a) Put a WARNING NOTICE(S) to tell persons not to start the engine.
(2) Make sure that the engine 1(2) shutdown occurred not less than 5 minutes before
you do this procedure.
(3) On the overhead maintenance panel 50VU:
(a) Make sure that the ON legend of the ENG/FADEC GND PWR/1(2)
pushbutton switch is off.
(b) Put a WARNING NOTICE(S) to tell persons not to energize the FADEC 1(2).
Subtask 78-11-11-010-051-A
B. Get Access
(1) Open the fan cowl doors: (Ref. AMM TASK 71-13-00-010-040)
(a) FOR 1000EM1 (ENGINE-1)
437AL, 438AR
(b) FOR 1000EM2 (ENGINE-2)
447AL, 448AR
(2) Put the ACCESS PLATFORM 1M(3 FT) in position
Subtask 78-11-11-040-050-A
C. Make the thrust reverser unserviceable (Ref. AMM TASK 78-30-00-481-041) .
Subtask 78-11-11-010-052-A
D. Open the thrust reverser doors: (Ref. AMM TASK 78-36-00-010-040)
(1) FOR 1000EM1 (ENGINE-1)
451AL, 452AR
(2) FOR 1000EM2 (ENGINE-2)
461AL, 462AR
4. Procedure

** ON A/C 103-159, 161-200

(Ref. Fig. Core Nozzle Assembly SHEET 1)

** ON A/C 103-159, 161-250

(Ref. Fig. Parts That Attach The Core Nozzle Assembly SHEET 1)
Subtask 78-11-11-020-050-B

WARNING:THE CORE NOZZLE ASSEMBLY WEIGHS APPROXIMATELY 162 POUNDS

(73,5 KG). MAKE SURE YOU SAFELY SUPPORT THE CORE NOZZLE
ASSEMBLY AND KEEP IT AWAY FROM OTHER ENGINE PARTS.

A. Removal of the core nozzle assembly

JCP Title: RP-C3244 C08 + HMA + HMB + W&B + CERTIFICATE OF TASK / INSPECTION COMPLETION: Page 4 of 5
LEASE RETURN DATABASE REV DATE: Aug 01/2019
JCP Ref: Service Order No.S4875119 CERTIFIES THAT THE TASK / INSPECTION HAS BEEN COMPLETED TO THE REQUIRED PRINT DATE: Sep 17/2019 12:18
STANDARD AND SUPPORTS THE FINAL MAINTENANCE RELEASE / CERTIFICATE OF RELEASE
TO SERVICE
 JOB CARD MPD-TASK:
CEB - A318/A319/A320/A321 AMM TASK : 78-11-11-000-041-A
78-11-11 PB 401

TITLE:
A/C Reg.:
78-11-11-000-041-A - Removal
RP-C3244
of the Core Nozzle Assembly
MECH. INSP.

NOTE: Foam can be put between the centerbody and the Core Nozzle Assembly

(1) Remove the Turbine Rear Frame (TRF) drain tube (20). (Ref. AMM TASK 71-73-
49-000-005)
(2) Remove the bolts (25), washers (30), and nuts (10) that attach the core nozzle
assembly (5) to the engine flange (88 locations).
(3) Remove the core nozzle assembly (5) from the engine.
*** END OF CARD ***

JCP Title: RP-C3244 C08 + HMA + HMB + W&B + CERTIFICATE OF TASK / INSPECTION COMPLETION: Page 5 of 5
LEASE RETURN DATABASE REV DATE: Aug 01/2019
JCP Ref: Service Order No.S4875119 CERTIFIES THAT THE TASK / INSPECTION HAS BEEN COMPLETED TO THE REQUIRED PRINT DATE: Sep 17/2019 12:18
STANDARD AND SUPPORTS THE FINAL MAINTENANCE RELEASE / CERTIFICATE OF RELEASE
TO SERVICE
 JOB CARD MPD-TASK:
CEB - A318/A319/A320/A321 AMM TASK : 78-11-11-400-041-A
78-11-11 PB 401

TITLE:
A/C Reg.:
78-11-11-400-041-A - Installation
RP-C3244
of the Core Nozzle Assembly
CARD: ZONE: INTERVAL:
SKILL: ACCESS: 437AL, 438AR, 451AL, 452AR, 447AL, 448AR, 461AL, 462AR

MECH. INSP.

** ON A/C 103-159, 161-250

TASK 78-11-11-400-041-A
Installation of the Core Nozzle Assembly

WARNING: BE CAREFUL WHEN YOU USE CONSUMABLE MATERIALS. OBEY THE

MATERIAL MANUFACTURER'S INSTRUCTIONS AND YOUR LOCAL
REGULATIONS.

FIN : 1000EM1 , 1000EM2

1. Reason for the Job
Self explanatory
2 Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE QTYDESIGNATION
No specific AR ACCESS PLATFORM 1M(3 FT)
No specific AR WARNING NOTICE(S)
No specific Torque wrench: range to between 50 and 70 lbf.in
(0.57 and 0.79 m.daN)

B. Consumable Materials

REFERENCE DESIGNATION
(Material No. CP2619) Never Seez-Pure Nickel, Special

C. Work Zones and Access Panels

ZONE/ACCESS ZONE DESCRIPTION

FOR 1000EM1 (ENGINE-1)
437AL, 438AR, 451AL,
452AR
FOR 1000EM2 (ENGINE-2)
447AL, 448AR, 461AL,
462AR

D. Referenced Information

REFERENCE DESIGNATION
(Ref. 71-13-00-010-040-B). Opening of the Fan Cowl Doors

JCP Title: RP-C3244 C08 + HMA + HMB + W&B + CERTIFICATE OF TASK / INSPECTION COMPLETION: Page 1 of 5
LEASE RETURN DATABASE REV DATE: Aug 01/2019
JCP Ref: Service Order No.S4875119 CERTIFIES THAT THE TASK / INSPECTION HAS BEEN COMPLETED TO THE REQUIRED PRINT DATE: Sep 17/2019 12:18
STANDARD AND SUPPORTS THE FINAL MAINTENANCE RELEASE / CERTIFICATE OF RELEASE
TO SERVICE
 JOB CARD MPD-TASK:
CEB - A318/A319/A320/A321 AMM TASK : 78-11-11-400-041-A
78-11-11 PB 401

TITLE:
A/C Reg.:
78-11-11-400-041-A - Installation
RP-C3244
of the Core Nozzle Assembly
MECH. INSP.

REFERENCE DESIGNATION
(Ref. 71-13-00-410-040-B). Closing of the Fan Cowl Doors
(Ref. 71-73-49-400-005-B). Installation of the Turbine Rear Frame Drain Tube
(Ref. 78-30-00-081-041-B). Make the Thrust Reverser Serviceable after Maintenance
(Ref. 78-30-00-481-041-B). Make the Thrust Reverser Unserviceable for
Maintenance
(Ref. 78-36-00-010-040-B). Opening of the Thrust Reverser Doors
(Ref. 78-36-00-410-040-B). Closing of the Thrust Reverser Doors

** ON A/C 103-159, 161-200

Core Nozzle Assembly SHEET 1
Parts That Attach The Core Nozzle Assembly SHEET 1

A A

FLANGE
STA 258 (A6)

FLANGE
CUTOUT

25 x88
10 x88
30 x88

15

DRAIN
FITTING
FLANGE
STA 252
C1M-311-03

20

N_MM_781111_4_RAN0_01_01

Figure 78(CFMB)-11-11-991-30100-06-B / SHEET 1/1 - Core Nozzle Assembly

** ON A/C 103-159, 161-200

JCP Title: RP-C3244 C08 + HMA + HMB + W&B + CERTIFICATE OF TASK / INSPECTION COMPLETION: Page 2 of 5
LEASE RETURN DATABASE REV DATE: Aug 01/2019
JCP Ref: Service Order No.S4875119 CERTIFIES THAT THE TASK / INSPECTION HAS BEEN COMPLETED TO THE REQUIRED PRINT DATE: Sep 17/2019 12:18
STANDARD AND SUPPORTS THE FINAL MAINTENANCE RELEASE / CERTIFICATE OF RELEASE
TO SERVICE
 JOB CARD MPD-TASK:
CEB - A318/A319/A320/A321 AMM TASK : 78-11-11-400-041-A
78-11-11 PB 401

TITLE:
A/C Reg.:
78-11-11-400-041-A - Installation
RP-C3244
of the Core Nozzle Assembly
MECH. INSP.

FLANGE
STA 258 (A6)
VIEW LOOKING
FWD

30

10
25
C1M-310-01

ENGINE FLANGE NOZZLE ASSEMBLY

TYPICAL 88 LOCATIONS

N_MM_781111_4_RBN0_01_01

Figure 78(CFMB)-11-11-991-30200-06-B / SHEET 1/

1 - Parts That Attach The Core Nozzle Assembly
** ON A/C 103-159, 161-250

JCP Title: RP-C3244 C08 + HMA + HMB + W&B + CERTIFICATE OF TASK / INSPECTION COMPLETION: Page 3 of 5
LEASE RETURN DATABASE REV DATE: Aug 01/2019
JCP Ref: Service Order No.S4875119 CERTIFIES THAT THE TASK / INSPECTION HAS BEEN COMPLETED TO THE REQUIRED PRINT DATE: Sep 17/2019 12:18
STANDARD AND SUPPORTS THE FINAL MAINTENANCE RELEASE / CERTIFICATE OF RELEASE
TO SERVICE
 JOB CARD MPD-TASK:
CEB - A318/A319/A320/A321 AMM TASK : 78-11-11-400-041-A
78-11-11 PB 401

TITLE:
A/C Reg.:
78-11-11-400-041-A - Installation
RP-C3244
of the Core Nozzle Assembly
MECH. INSP.

3. Job Set-up
Subtask 78-11-11-860-050-A
A. Aircraft Maintenance Configuration
(1) On the center pedestal, on the ENG panel 115VU, make sure that a WARNING
NOTICE(S) is in position to tell persons not to start the engine.
(2) On the overhead maintenance panel 50VU, make sure that the ON legend of
the ENG/FADEC GND PWR/1(2) pushbutton switch is off. Make sure that a
WARNING NOTICE(S) is in position to tell persons not to energize the FADEC
1(2).
(3) Make sure that the ACCESS PLATFORM 1M(3 FT) is in position.
Subtask 78-11-11-010-054-A
B. Get Access
(1) Make sure that the fan cowl doors are open: (Ref. AMM TASK 71-13-00-010-
040)
(a) FOR 1000EM1 (ENGINE-1)
437AL, 438AR
(b) FOR 1000EM2 (ENGINE-2)
447AL, 448AR
(2) Make sure that the thrust reverser doors are open: (Ref. AMM TASK 78-36-00-
010-040)
(a) FOR 1000EM1 (ENGINE-1)
451AL, 452AR
(b) FOR 1000EM2 (ENGINE-2)
461AL, 462AR
Subtask 78-11-11-040-052-A
C. Make sure that the thrust reverser is unserviceable (Ref. AMM TASK 78-30-00-481-
041) .
4. Procedure

** ON A/C 103-159, 161-200

(Ref. Fig. Core Nozzle Assembly SHEET 1)

** ON A/C 103-159, 161-250

(Ref. Fig. Parts That Attach The Core Nozzle Assembly SHEET 1)
Subtask 78-11-11-420-050-B
A. Installation of the core nozzle assembly.

WARNING:THE CORE NOZZLE ASSEMBLY WEIGHS APPROXIMATELY 162

POUNDS (73,5 KG). MAKE SURE YOU SAFELY SUPPORT THE CORE
NOZZLE ASSEMBLY AND KEEP IT AWAY FROM OTHER ENGINE
PARTS.

JCP Title: RP-C3244 C08 + HMA + HMB + W&B + CERTIFICATE OF TASK / INSPECTION COMPLETION: Page 4 of 5
LEASE RETURN DATABASE REV DATE: Aug 01/2019
JCP Ref: Service Order No.S4875119 CERTIFIES THAT THE TASK / INSPECTION HAS BEEN COMPLETED TO THE REQUIRED PRINT DATE: Sep 17/2019 12:18
STANDARD AND SUPPORTS THE FINAL MAINTENANCE RELEASE / CERTIFICATE OF RELEASE
TO SERVICE
 JOB CARD MPD-TASK:
CEB - A318/A319/A320/A321 AMM TASK : 78-11-11-400-041-A
78-11-11 PB 401

TITLE:
A/C Reg.:
78-11-11-400-041-A - Installation
RP-C3244
of the Core Nozzle Assembly
MECH. INSP.

(1) Carefully move the core nozzle assembly forward over the centerbody.
(2) Align the core nozzle assembly (5) with the aft engine flange. Make sure that the
cutouts in the nozzle flange are aligned with the cutouts in the engine flange.
(3) Apply Never Seez-Pure Nickel, Special (Material No. CP2619) to the bolt (25)
threads.

NOTE: Put the countersunk side of the washer against the head of the bolt.

(4) Attach the core nozzle (5) to the engine flange with the bolts (25), washers (30),
and nuts (10) (88 locations). Do not torque the nuts at this time.
(5) Install the turbine rear frame drain tube (20). (Ref. AMM TASK 71-73-49-400-
005)
(6) Adjust the core nozzle assembly (5) position so it is aligned for the best exhaust
gas flowpath.
(7) TORQUE the nuts (10) to between 50 and 70 lbf.in (0.57 and 0.79 m.daN).

NOTE: Start with the nuts at the 3 o'clock and 9 o'clock positions. Then torque the
nuts in sequence on opposite sides of the engine.

5. Close-up
Subtask 78-11-11-410-051-A
A. Close Access
(1) Make sure that the work area is clean and clear of tools and other items.
(2) Close the thrust reverser cowl doors: (Ref. AMM TASK 78-36-00-410-040)
(a) FOR 1000EM1 (ENGINE-1)
451AL, 452AR
(b) FOR 1000EM2 (ENGINE-2)
461AL, 462AR
(3) Remove the access platform(s).
Subtask 78-11-11-440-050-A
B. Make the thrust reverser serviceable (Ref. AMM TASK 78-30-00-081-041) .
Subtask 78-11-11-410-052-A
C. Close Access
(1) Close the fan cowl doors: (Ref. AMM TASK 71-13-00-410-040)
(a) FOR 1000EM1 (ENGINE-1)
437AL, 438AR
(b) FOR 1000EM2 (ENGINE-2)
447AL, 448AR
(2) Remove the WARNING NOTICE(S).
*** END OF CARD ***

JCP Title: RP-C3244 C08 + HMA + HMB + W&B + CERTIFICATE OF TASK / INSPECTION COMPLETION: Page 5 of 5
LEASE RETURN DATABASE REV DATE: Aug 01/2019
JCP Ref: Service Order No.S4875119 CERTIFIES THAT THE TASK / INSPECTION HAS BEEN COMPLETED TO THE REQUIRED PRINT DATE: Sep 17/2019 12:18
STANDARD AND SUPPORTS THE FINAL MAINTENANCE RELEASE / CERTIFICATE OF RELEASE
TO SERVICE
 JOB CARD MPD-TASK:
CEB - A318/A319/A320/A321 AMM TASK : 78-11-12-000-041-A
78-11-12 PB 401

TITLE:
A/C Reg.:
78-11-12-000-041-A - Removal of the Centerbody
RP-C3244

CARD: ZONE: INTERVAL:

SKILL: ACCESS:

MECH. INSP.

** ON A/C 103-159, 161-250

TASK 78-11-12-000-041-A
Removal of the Centerbody

FIN : 1000EM1 , 1000EM2

1. Reason for the Job
Self explanatory
2 Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE QTYDESIGNATION
No specific AR WARNING NOTICE(S)

B. Referenced Information

REFERENCE DESIGNATION
(Ref. 72-56-00-210-002-A). Inspection/Check of the Turbine Frame Assembly
(Ref. 78-11-11-000-041-A). Removal of the Core Nozzle Assembly
Centerbody SHEET 1

JCP Title: RP-C3244 C08 + HMA + HMB + W&B + CERTIFICATE OF TASK / INSPECTION COMPLETION: Page 1 of 3
LEASE RETURN DATABASE REV DATE: Aug 01/2019
JCP Ref: Service Order No.S4875119 CERTIFIES THAT THE TASK / INSPECTION HAS BEEN COMPLETED TO THE REQUIRED PRINT DATE: Sep 17/2019 12:18
STANDARD AND SUPPORTS THE FINAL MAINTENANCE RELEASE / CERTIFICATE OF RELEASE
TO SERVICE
 JOB CARD MPD-TASK:
CEB - A318/A319/A320/A321 AMM TASK : 78-11-12-000-041-A
78-11-12 PB 401

TITLE:
A/C Reg.:
78-11-12-000-041-A - Removal of the Centerbody
RP-C3244
MECH. INSP.

A
5

10
(16 PLACES)

15
(16 PLACES)

FLANGE
STA 257

C1M-288-00
N_MM_781112_4_RAM0_01_00

Figure 78(CFMB)-11-12-991-30000-06-A / SHEET 1/1 - Centerbody

** ON A/C 103-159, 161-250

JCP Title: RP-C3244 C08 + HMA + HMB + W&B + CERTIFICATE OF TASK / INSPECTION COMPLETION: Page 2 of 3
LEASE RETURN DATABASE REV DATE: Aug 01/2019
JCP Ref: Service Order No.S4875119 CERTIFIES THAT THE TASK / INSPECTION HAS BEEN COMPLETED TO THE REQUIRED PRINT DATE: Sep 17/2019 12:18
STANDARD AND SUPPORTS THE FINAL MAINTENANCE RELEASE / CERTIFICATE OF RELEASE
TO SERVICE
 JOB CARD MPD-TASK:
CEB - A318/A319/A320/A321 AMM TASK : 78-11-12-000-041-A
78-11-12 PB 401

TITLE:
A/C Reg.:
78-11-12-000-041-A - Removal of the Centerbody
RP-C3244
MECH. INSP.

3. Job Set-up
Subtask 78-11-12-941-050-A
A. Safety Precautions
(1) On the center pedestal, on the ENG panel 115VU:
(a) Put a WARNING NOTICE(S) to tell persons not to start the engine.
(2) Make sure that the engine 1(2) shutdown occurred not less than 5 minutes before
you do this procedure.
(3) On the overhead maintenance panel 50VU:
(a) Make sure that the ON legend of the ENG/FADEC GND PWR/1(2)
pushbutton switch is off.
(b) Put a WARNING NOTICE(S) to tell persons not to energize the FADEC 1(2).
Subtask 78-11-12-010-050-A
B. Remove the core nozzle (Ref. AMM TASK 78-11-11-000-041) .
4. Procedure
(Ref. Fig. Centerbody SHEET 1)
Subtask 78-11-12-020-050-A
A. Removal of the Centerbody:
(1) Remove the nut (10) and washers (15) attaching centerbody to the engine.
Discard nuts.

NOTE: If any anomaly occurs when removing nuts (loosing or broken stud),
(Ref. AMM TASK 72-56-00-210-002) for serviceability or repair.

(2) Remove centerbody (5) from engine.

*** END OF CARD ***

JCP Title: RP-C3244 C08 + HMA + HMB + W&B + CERTIFICATE OF TASK / INSPECTION COMPLETION: Page 3 of 3
LEASE RETURN DATABASE REV DATE: Aug 01/2019
JCP Ref: Service Order No.S4875119 CERTIFIES THAT THE TASK / INSPECTION HAS BEEN COMPLETED TO THE REQUIRED PRINT DATE: Sep 17/2019 12:18
STANDARD AND SUPPORTS THE FINAL MAINTENANCE RELEASE / CERTIFICATE OF RELEASE
TO SERVICE
 JOB CARD MPD-TASK:
CEB - A318/A319/A320/A321 AMM TASK : 78-11-12-400-041-A
78-11-12 PB 401

TITLE:
A/C Reg.:
78-11-12-400-041-A - Installation of the Centerbody
RP-C3244

CARD: ZONE: INTERVAL:

SKILL: ACCESS:

MECH. INSP.

** ON A/C 103-159, 161-250

TASK 78-11-12-400-041-A
Installation of the Centerbody

FIN : 1000EM1 , 1000EM2

1. Reason for the Job
Self explanatory
2 Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE QTYDESIGNATION
No specific AR WARNING NOTICE(S)
No specific Torque wrench: range to between 220 and 240 lbf.in
(2.49 and 2.71 m.daN)

B. Consumable Materials

REFERENCE DESIGNATION
(Material No. CP2619) Never Seez-Pure Nickel, Special

C. Expendable Parts

FIG.ITEM DESIGNATION IPC-CSN

10 nuts 78-11-12-01-010

D. Referenced Information

REFERENCE DESIGNATION
(Ref. 72-56-00-210-002-A). Inspection/Check of the Turbine Frame Assembly
(Ref. 78-11-11-000-041-A). Removal of the Core Nozzle Assembly
(Ref. 78-11-11-400-041-A). Installation of the Core Nozzle Assembly
Centerbody SHEET 1

JCP Title: RP-C3244 C08 + HMA + HMB + W&B + CERTIFICATE OF TASK / INSPECTION COMPLETION: Page 1 of 3
LEASE RETURN DATABASE REV DATE: Aug 01/2019
JCP Ref: Service Order No.S4875119 CERTIFIES THAT THE TASK / INSPECTION HAS BEEN COMPLETED TO THE REQUIRED PRINT DATE: Sep 17/2019 12:18
STANDARD AND SUPPORTS THE FINAL MAINTENANCE RELEASE / CERTIFICATE OF RELEASE
TO SERVICE
 JOB CARD MPD-TASK:
CEB - A318/A319/A320/A321 AMM TASK : 78-11-12-400-041-A
78-11-12 PB 401

TITLE:
A/C Reg.:
78-11-12-400-041-A - Installation of the Centerbody
RP-C3244
MECH. INSP.

A
5

10
(16 PLACES)

15
(16 PLACES)

FLANGE
STA 257

C1M-288-00
N_MM_781112_4_RAM0_01_00

Figure 78(CFMB)-11-12-991-30000-06-A / SHEET 1/1 - Centerbody

** ON A/C 103-159, 161-250

JCP Title: RP-C3244 C08 + HMA + HMB + W&B + CERTIFICATE OF TASK / INSPECTION COMPLETION: Page 2 of 3
LEASE RETURN DATABASE REV DATE: Aug 01/2019
JCP Ref: Service Order No.S4875119 CERTIFIES THAT THE TASK / INSPECTION HAS BEEN COMPLETED TO THE REQUIRED PRINT DATE: Sep 17/2019 12:18
STANDARD AND SUPPORTS THE FINAL MAINTENANCE RELEASE / CERTIFICATE OF RELEASE
TO SERVICE
 JOB CARD MPD-TASK:
CEB - A318/A319/A320/A321 AMM TASK : 78-11-12-400-041-A
78-11-12 PB 401

TITLE:
A/C Reg.:
78-11-12-400-041-A - Installation of the Centerbody
RP-C3244
MECH. INSP.

3. Job Set-up
Subtask 78-11-12-860-050-A
A. Aircraft Maintenance Configuration
(1) On the center pedestal, on the ENG panel 115VU, make sure that a WARNING
NOTICE(S) is in position to tell persons not to start the engine.
(2) On the overhead maintenance panel 50VU, make sure that the ON legend of
the ENG/FADEC GND PWR/1(2) pushbutton switch is off. Make sure that a
WARNING NOTICE(S) is in position to tell persons not to energize the FADEC
1(2).
(3) Make sure that the core nozzle is removed (Ref. AMM TASK 78-11-11-000-041) .
4. Procedure
(Ref. Fig. Centerbody SHEET 1)
Subtask 78-11-12-420-050-A
A. Installation of the Centerbody:

NOTE: Make sure there are two rows of drain holes on the centerbody. If not, refer to
SB RA32178-4 "Addition of Centerbody Drain Holes".

(1) Put the centerbody (5) on the studs in the engine flange.
(2) Apply Never Seez-Pure Nickel, Special (Material No. CP2619) to the threads of
the engine studs.
(3) Attach centerbody to the engine studs with new IPC -CSN (78-11-12-01-
010) nuts (10) and washers (15).

NOTE: Make sure that you attach the centerbody to the engine with new nuts. Do
not use nuts that were used before.

(4) Adjust the centerbody (5) position to minimize flowpath mismatch.

(5) TORQUE nuts (10) to between 220 and 240 lbf.in (2.49 and 2.71 m.daN).

NOTE: If any anomaly occurs when removing nuts (loosing or broken stud),
(Ref. AMM TASK 72-56-00-210-002) for serviceability or repair.

5. Close-up
Subtask 78-11-12-410-050-A
A. Close Access
(1) Make sure that the work area is clean and clear of tools and other items.
(2) Install the core nozzle (Ref. AMM TASK 78-11-11-400-041) .
(3) Remove the WARNING NOTICE(S).
*** END OF CARD ***

JCP Title: RP-C3244 C08 + HMA + HMB + W&B + CERTIFICATE OF TASK / INSPECTION COMPLETION: Page 3 of 3
LEASE RETURN DATABASE REV DATE: Aug 01/2019
JCP Ref: Service Order No.S4875119 CERTIFIES THAT THE TASK / INSPECTION HAS BEEN COMPLETED TO THE REQUIRED PRINT DATE: Sep 17/2019 12:18
STANDARD AND SUPPORTS THE FINAL MAINTENANCE RELEASE / CERTIFICATE OF RELEASE
TO SERVICE
 JOB CARD MPD-TASK:
CEB - A318/A319/A320/A321 AMM TASK : 72-56-00-000-001-A
72-56-00 PB 401

TITLE:
A/C Reg.:
72-56-00-000-001-A - Removal of the
RP-C3244
Flame Arrestor and Flange Assembly
CARD: ZONE: INTERVAL:
SKILL: ACCESS:

MECH. INSP.

** ON A/C 103-159, 161-250

TASK 72-56-00-000-001-A
Removal of the Flame Arrestor and Flange Assembly

FIN : 1000EM1 , 1000EM2

1. Reason for the Job
To allow the inspection/check and the cleaning of the rear sump oil supply tube in the LPT
frame.
2 Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE QTYDESIGNATION
No specific AR WARNING NOTICE(S)

B. Referenced Information

REFERENCE DESIGNATION
(Ref. 78-11-11-000-041-A). Removal of the Core Nozzle Assembly
(Ref. 78-11-12-000-041-A). Removal of the Centerbody
Flame Arrestor and Flange Assembly SHEET 1

JCP Title: RP-C3244 C08 + HMA + HMB + W&B + CERTIFICATE OF TASK / INSPECTION COMPLETION: Page 1 of 3
LEASE RETURN DATABASE REV DATE: Aug 01/2019
JCP Ref: Service Order No.S4875119 CERTIFIES THAT THE TASK / INSPECTION HAS BEEN COMPLETED TO THE REQUIRED PRINT DATE: Sep 17/2019 12:18
STANDARD AND SUPPORTS THE FINAL MAINTENANCE RELEASE / CERTIFICATE OF RELEASE
TO SERVICE
 JOB CARD MPD-TASK:
CEB - A318/A319/A320/A321 AMM TASK : 72-56-00-000-001-A
72-56-00 PB 401

TITLE:
A/C Reg.:
72-56-00-000-001-A - Removal of the
RP-C3244
Flame Arrestor and Flange Assembly
MECH. INSP.

A 170
PLATE
LOCK

160
FLANGE
ASSY

150
BOLT

20
BOLT

80
GASKET
SEAL

LPT OIL
FRAME INLET 30
COVER FLAME
70 ARRESTOR
BOLT
S-M56-MM-04304-00-B

N_MM_725600_4_RAP0_01_00

Figure 72(CFMB)-56-00-991-30000-06-C / SHEET

1/1 - Flame Arrestor and Flange Assembly
** ON A/C 103-159, 161-250

JCP Title: RP-C3244 C08 + HMA + HMB + W&B + CERTIFICATE OF TASK / INSPECTION COMPLETION: Page 2 of 3
LEASE RETURN DATABASE REV DATE: Aug 01/2019
JCP Ref: Service Order No.S4875119 CERTIFIES THAT THE TASK / INSPECTION HAS BEEN COMPLETED TO THE REQUIRED PRINT DATE: Sep 17/2019 12:18
STANDARD AND SUPPORTS THE FINAL MAINTENANCE RELEASE / CERTIFICATE OF RELEASE
TO SERVICE
 JOB CARD MPD-TASK:
CEB - A318/A319/A320/A321 AMM TASK : 72-56-00-000-001-A
72-56-00 PB 401

TITLE:
A/C Reg.:
72-56-00-000-001-A - Removal of the
RP-C3244
Flame Arrestor and Flange Assembly
MECH. INSP.

3. Job Set-up
Subtask 72-56-00-941-052-A
A. Safety Precautions
(1) On the center pedestal, on the ENG panel 115VU:
(a) Put a WARNING NOTICE(S) to tell persons not to start the engine.
(2) Make sure that the engine 1(2) shutdown occurred not less than 5 minutes before
you do this procedure.
(3) On the overhead maintenance panel 50VU:
(a) Make sure that the ON legend of the ENG/FADEC GND PWR/1(2)
pushbutton switch is off.
(b) Put a WARNING NOTICE(S) to tell persons not to energize the FADEC 1(2).
Subtask 72-56-00-010-055-A
B. Get Access
(1) Remove the core nozzle (Ref. AMM TASK 78-11-11-000-041) .
(2) Remove the centerbody (Ref. AMM TASK 78-11-12-000-041) .
4. Procedure
(Ref. Fig. Flame Arrestor and Flange Assembly SHEET 1)
Subtask 72-56-00-020-050-B
A. Removal of the Flame Arrestor
(1) Remove the six bolts (20) which attach the flame arrestor (30) to the oil inlet cover
through the flange assembly (160).
Subtask 72-56-00-020-051-B
B. Removal of the Flange Assembly

NOTE: This procedure is for Turbine Frame with Tangential Symetrical Section Struts
only.

(1) Remove the sixteen bolts (150) which attach the flow path fairing to the outer circle
of the flange assembly (160) through the plate lock (170).
PRE SB CFMI 72-681
(2) Remove the twenty four bolts (70) which attach the mid circle of the flange
assembly (160) to the LPT frame hub rear flange.
POST SB CFMI 72-681
(3) Remove the eight bolts (70) which attach the flange assembly (160) to the LPT
frame.
END OF SB CFMI 72-681
(4) Remove the flange assembly (160) from the LPT frame.
(5) Remove and discard the gasket seal (80).
*** END OF CARD ***

JCP Title: RP-C3244 C08 + HMA + HMB + W&B + CERTIFICATE OF TASK / INSPECTION COMPLETION: Page 3 of 3
LEASE RETURN DATABASE REV DATE: Aug 01/2019
JCP Ref: Service Order No.S4875119 CERTIFIES THAT THE TASK / INSPECTION HAS BEEN COMPLETED TO THE REQUIRED PRINT DATE: Sep 17/2019 12:18
STANDARD AND SUPPORTS THE FINAL MAINTENANCE RELEASE / CERTIFICATE OF RELEASE
TO SERVICE
 JOB CARD MPD-TASK:
CEB - A318/A319/A320/A321 AMM TASK : 72-56-00-400-001-A
72-56-00 PB 401

TITLE:
A/C Reg.:
72-56-00-400-001-A - Installation of the
RP-C3244
Flame Arrestor and Flange Assembly
CARD: ZONE: INTERVAL:
SKILL: ACCESS:

MECH. INSP.

** ON A/C 103-159, 161-250

TASK 72-56-00-400-001-A
Installation of the Flame Arrestor and Flange Assembly

FIN : 1000EM1 , 1000EM2

1. Reason for the Job
Self explanatory
2 Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE QTYDESIGNATION
No specific AR WARNING NOTICE(S)
No specific Torque wrench: range to between 110 and 120 lbf.in
(1.24 and 1.36 m.daN)

B. Consumable Materials

REFERENCE DESIGNATION
(Material No. CP2101) graphite grease

C. Expendable Parts

FIG.ITEM DESIGNATION IPC-CSN

80 gasket seal 72-56-00-02-010

D. Referenced Information

REFERENCE DESIGNATION
(Ref. 78-11-11-000-041-A). Removal of the Core Nozzle Assembly
(Ref. 78-11-11-400-041-A). Installation of the Core Nozzle Assembly
(Ref. 78-11-12-000-041-A). Removal of the Centerbody
(Ref. 78-11-12-400-041-A). Installation of the Centerbody
Flame Arrestor and Flange Assembly SHEET 1

JCP Title: RP-C3244 C08 + HMA + HMB + W&B + CERTIFICATE OF TASK / INSPECTION COMPLETION: Page 1 of 4
LEASE RETURN DATABASE REV DATE: Aug 01/2019
JCP Ref: Service Order No.S4875119 CERTIFIES THAT THE TASK / INSPECTION HAS BEEN COMPLETED TO THE REQUIRED PRINT DATE: Sep 17/2019 12:18
STANDARD AND SUPPORTS THE FINAL MAINTENANCE RELEASE / CERTIFICATE OF RELEASE
TO SERVICE
 JOB CARD MPD-TASK:
CEB - A318/A319/A320/A321 AMM TASK : 72-56-00-400-001-A
72-56-00 PB 401

TITLE:
A/C Reg.:
72-56-00-400-001-A - Installation of the
RP-C3244
Flame Arrestor and Flange Assembly
MECH. INSP.

A 170
PLATE
LOCK

160
FLANGE
ASSY

150
BOLT

20
BOLT

80
GASKET
SEAL

LPT OIL
FRAME INLET 30
COVER FLAME
70 ARRESTOR
BOLT
S-M56-MM-04304-00-B

N_MM_725600_4_RAP0_01_00

Figure 72(CFMB)-56-00-991-30000-06-C / SHEET

1/1 - Flame Arrestor and Flange Assembly
** ON A/C 103-159, 161-250

JCP Title: RP-C3244 C08 + HMA + HMB + W&B + CERTIFICATE OF TASK / INSPECTION COMPLETION: Page 2 of 4
LEASE RETURN DATABASE REV DATE: Aug 01/2019
JCP Ref: Service Order No.S4875119 CERTIFIES THAT THE TASK / INSPECTION HAS BEEN COMPLETED TO THE REQUIRED PRINT DATE: Sep 17/2019 12:18
STANDARD AND SUPPORTS THE FINAL MAINTENANCE RELEASE / CERTIFICATE OF RELEASE
TO SERVICE
 JOB CARD MPD-TASK:
CEB - A318/A319/A320/A321 AMM TASK : 72-56-00-400-001-A
72-56-00 PB 401

TITLE:
A/C Reg.:
72-56-00-400-001-A - Installation of the
RP-C3244
Flame Arrestor and Flange Assembly
MECH. INSP.

3. Job Set-up
Subtask 72-56-00-860-050-A
A. Aircraft Maintenance Configuration
(1) On the center pedestal, on the ENG panel 115VU, make sure that a WARNING
NOTICE(S) is in position to tell persons not to start the engine.
(2) On the overhead maintenance panel 50VU, make sure that the ON legend of the
ENG/FADEC GND PWR/1(2) is off. Make sure that a WARNING NOTICE(S) is in
position to tell persons not to energize the FADEC 1(2).
(3) Make sure that the core nozzle is removed (Ref. AMM TASK 78-11-11-000-041) .
(4) Make sure that the centerbody is removed (Ref. AMM TASK 78-11-12-000-041) .
4. Procedure
(Ref. Fig. Flame Arrestor and Flange Assembly SHEET 1)
Subtask 72-56-00-420-050-B
A. Installation of the Flange Assembly

NOTE: This procedure is for Turbine Frame with Tangential Symmetrical Section
Structs only.

(1) Install a new IPC -CSN (72-56-00-02-010) gasket seal (80) on the rear flange of
the oil inlet cover.
(2) Install the flange assembly (160) in position on the LPT frame with flow path fairing
and plate lock (170) installed.
(3) Lubricating of the threads of bolts

CAUTION:MAKE SURE THAT THE GASKET SEAL IS IN THE CORRECT

POSITION ON THE REAR FLANGE OF THE OIL INLET COVER.

(a) Lubricate the threads of bolts (70) with graphite

grease (Material No. CP2101).

NOTE: Make sure that the flange assembly is correctly positioned with the aft
sump overboard seal drain tube in its position.

PRE SB CFMI 72-681

(4) Attach the flange assembly (160) with twenty four bolts (70) to the hub inner rear
flange of LPT frame.
POST SB CFMI 72-681
(5) Attach the flange assembly (160) with eight bolts (70) to the hub inner rear flange.
END OF SB 72-681
(6) TORQUE the bolts (70) to between 110 and 120 lbf.in (1.24 and 1.36 m.daN).
(7) Lubricate the threads of bolts (150) with graphite grease (Material No. CP2101).
(8) Attach the flange assembly (160) with sixteen bolts (150) to the flow path fairing
installed on LPT frame through the plate lock (170).
JCP Title: RP-C3244 C08 + HMA + HMB + W&B + CERTIFICATE OF TASK / INSPECTION COMPLETION: Page 3 of 4
LEASE RETURN DATABASE REV DATE: Aug 01/2019
JCP Ref: Service Order No.S4875119 CERTIFIES THAT THE TASK / INSPECTION HAS BEEN COMPLETED TO THE REQUIRED PRINT DATE: Sep 17/2019 12:18
STANDARD AND SUPPORTS THE FINAL MAINTENANCE RELEASE / CERTIFICATE OF RELEASE
TO SERVICE
 JOB CARD MPD-TASK:
CEB - A318/A319/A320/A321 AMM TASK : 72-56-00-400-001-A
72-56-00 PB 401

TITLE:
A/C Reg.:
72-56-00-400-001-A - Installation of the
RP-C3244
Flame Arrestor and Flange Assembly
MECH. INSP.

(9) TORQUE the bolts (150) to between 110 and 120 lbf.in (1.24 and 1.36 m.daN).
Subtask 72-56-00-420-051-B
B. Installation of the Flame Arrestor
(1) Lubricate the threads of bolts (20) with graphite grease (Material No. CP2101).
(2) Install the flame arrestor (30) in position on the flange assembly (160).
(3) Attach the flame arrestor with six bolts (20).
(4) TORQUE the bolts (20) to between 110 and 120 lbf.in (1.24 and 1.36 m.daN).
5. Close-up
Subtask 72-56-00-410-056-A
A. Close Access
(1) Make sure that the work area is clean and clear of tools and other items.
(2) Install the centerbody (Ref. AMM TASK 78-11-12-400-041) .
(3) Install the core nozzle (Ref. AMM TASK 78-11-11-400-041) .
(4) Remove the WARNING NOTICE(S).
*** END OF CARD ***

JCP Title: RP-C3244 C08 + HMA + HMB + W&B + CERTIFICATE OF TASK / INSPECTION COMPLETION: Page 4 of 4
LEASE RETURN DATABASE REV DATE: Aug 01/2019
JCP Ref: Service Order No.S4875119 CERTIFIES THAT THE TASK / INSPECTION HAS BEEN COMPLETED TO THE REQUIRED PRINT DATE: Sep 17/2019 12:18
STANDARD AND SUPPORTS THE FINAL MAINTENANCE RELEASE / CERTIFICATE OF RELEASE
TO SERVICE