E2209wf - Monitor - 44 - 51

Service Manual
Service Manual
LCD Monitor E2209Wf
0
Downloaded from www.Manualslib.com manuals search engine
1
Service Manual Versions and Revision

No. Version Release Date Revision
1 1.0 2008-6-3 Initial Release
Copyright
Copyright 2007 InnoLux Display. Corp. Ltd
All Rights Reserved
This manual may not, in whole or in part, be copied, Photocopied, reproduced, translated, or converted to any
electronic or machine readable form without prior written permission of Foxconn Tech. Corp. Ltd.
Dell E2209W Service Manual

Service Manual
Table of Contents
CHAPTER 1- PRECAUTIONS & SAFETY NOTICES ...................................................................................................................... 3
1. SAFETY PRECAUTIONS...................................................................................................................................................... 3
2. PRODUCT SAFETY NOTICE ............................................................................................................................................... 3
3. SERVICE NOTES ................................................................................................................................................................... 3
CHAPTER 2- SERVICE TOOLS & EQUIPMENT REQUIRED....................................................................................................... 4
CHAPTER 3- CIRCUIT THEORY ........................................................................................................................................................ 5
1. BLOCK DIAGRAM ..................................................................................................................................................................... 5
2. ELECTRONIC CIRCUIT THEORY ................................................................................................................................................ 7
3. FACTORY PRESET TIMING TABLE ................................................................................................................................. 13
4. POWER ON/OFF SEQUENCY ................................................................................................................................................... 13
5. D-SUB CONNECTOR PIN ASSIGNMENT .................................................................................................................................. 14
6. AC OUTLET PIN ASSIGNMENT ............................................................................................................................................... 14
7. INNER CONNECTOR PIN ASSIGNMENT .................................................................................................................................... 14
8. KEY PARTS PIN ASSIGNMENTS ............................................................................................................................................... 16
CHAPTER 4- DISASSEMBLY & ASSEMBLY .................................................................................................................................. 21
1. EXPLODED DIAGRAM ............................................................................................................................................................. 21
2. E2209WFPF DISASSEMBLY BLOCK ....................................................................................................................................... 22
3. ASSEMBLY BLOCK.................................................................................................................................................................. 23
CHAPTER 5- TEST AND ADJUSTMENT ......................................................................................................................................... 24
1. FUNCTION KEY DEFINITIONS .................................................................................................................................................. 24
2. OSD CONTROL....................................................................................................................................................................... 24
3. FACTORY MODE INTRODUCTION ............................................................................................................................................ 26
4. BURN-IN PATTERN .................................................................................................................................................................. 27
5. AUTO COLOR BALANCE (AUTOMATICALLY CALIBRATE CHIP ADC PARAMETER BY USING CHIP INTERNAL DAC.) ................ 27
6. UPLOAD FIRMWARE TO MCU VIA VGA CABLE...................................................................................................................... 26
7. AFTER REPAIR, TO ENSURE THE QUALITY YOU SHOULD DO THE FOLLOWING TEST AND ADJUSTMENT. ................................... 27
CHAPTER 6- TROUBLE SHOOTING ............................................................................................................................................... 30
1. COMMON ACKNOWLEDGE...................................................................................................................................................... 30
2. NO POWER LED OFF.............................................................................................................................................................. 30
3. POWER NORMAL LED AMBER ................................................................................................................................................ 31
4. BACKLIGHT CAN’T BE TURNED ON ......................................................................................................................................... 32
5. NO PICTURE BACKLIGHT ON ................................................................................................................................................ 33
6. AT 32-GRAY SCALE PATTERN, COLOR LOST IN SOME SCALE .................................................................................................... 34
CHAPTER 7- RECOMMENDED PART LIST................................................................................................................................... 35
ATTACHMENT 1- BILL OF MATERIAL .......................................................................................................................................... 37
ATTACHMENT 2- SCHEMATIC ........................................................................................................................................................ 47
ATTACHMENT 3- PCB LAYOUT....................................................................................................................................................... 60
2
Service Manual
Chapter 1- PRECAUTIONS & SAFETY NOTICES
SAFETY PRECAUTIONS
This monitor is manufactured and tested on a ground principle that a user’s safety comes first.
However, improper used or installation may cause damage to the monitor as well as to the user.
WARNINGS:
 This monitor should be operated only at the correct power sources indicated on the rating label on
the rear cover of the monitor. If you’re unsure the power supply in your residence, consult your
local dealer or Power Company.
 Use only the specified power cord that comes with this monitor.
 Do not try to repair the monitor by yourself, as it contains no user-serviceable parts. This monitor
should only be repaired by a qualified technician.
 Do not remove the monitor cabinet. There is high-voltage parts inside that may cause electric shock
to human bodies.
 Stop using the monitor if the cabinet is damaged. Have it checked by a service technician.
 Put your monitor only in a lean, cool, dry environment. If it gets wet, unplug the power cable
immediately and consult your closed dealer.
 Always unplug the monitor before cleaning it. Clean the cabinet with a clean, dry cloth. Apply
non-ammonia based cleaner onto the cloth, not directly onto the class screen.
 Do not place heavy objects on the monitor or power cord.
PRODUCT SAFETY NOTICE
Many electrical and mechanical parts in this chassis have special safety visual inspections and the
protection afforded by them cannot necessarily be obtained by using replacement components rated
for higher voltage, wattage, etc. Before replacing any of these components read the parts list in this
manual carefully. The use of substitute replacement parts, which do not have the same safety
characteristics as specified in the parts list, may create shock, fire, or other hazards.
SERVICE NOTES
 When replacing parts on circuit boards, clamp the solder wires around terminals before soldering.
 Keep wires away from high voltage, high temperature components and sharp edges.
 Keep wires in their original position so as to reduce interference.
 Adjustment of this product please refers to the user’ manual.
 Use Pb free solder wire for circuit board preparation.
3
Service Manual
Chapter 2- SERVICE TOOLS & EQUIPMENT REQUIRED
1. SIGNAL GENERATOR
2. MULTIMETER
3. SCREW DRIVER
4. OSCILLOSCOPE
5. Soldering IRON
6. SOLDER (Lead free, RoHS compliance)
7. Color Analyzer
8. Fox_VISP_Programmer
9. Fox_VEDID_Programmer
4
Service Manual
Chapter 3- CIRCUIT THEORY
Block Diagram
There are 3pcs PCBA in this monitor, one is power& inverter&Audio board which is a single layer board,
one is interface board including USB HUB 1up/2down, one is keypad which is OSD control, and one is
USB transfer board located on the right side back cover. The system function block diagram as below
This PWA is included switching power supplier, inverter for CCFL and interface board.(fig.1)
INVERTER POWER
Fig.1
5
Service Manual
Fig.12
6
Service Manual
Electronic Circuit Theory

2.1 Inverter PWM circuit
2.1.1)Inverter Control circuit:(fig.2)
Fig.2
27VDC provides the power for U1; the control signals Brightness and ON/OFF come from I/F
board. ON/OFF signal connect to pin16 of U1 and makes U1 enable. Brightness signal connect to
pin12 of U1 and regulates the panel brightness, make up a network of delaying time circuit and R23
make up a divided voltage network, C3 is used to control start-up timing. The operation
frequency is determined by the external Resistor R16 and capacitor C8 connected to pin3 of U1.
C7 is used for soft start and compensation.
The output drives, include DRV1, DRV2 (pins8,9 respectively) output square pulses to drive
MOSFET Q6, Q7 and each of Q6, Q7 is consist of a N+P channel MOSFET. Q6 and Q7 work as All
Bridge structure, it is high efficient, PWM switching.
During start up, VSEN (pin1) senses the voltage at the transformer secondary. When VSEN
reaches 3.0V, the output voltage is regulated. If no current is sensed approximately 2seconds U1 shut
off.
The current flowing through CCFL is sensed and regulated through sense resistor R6, R19. The
feedback voltage connected to Pin1 (ISEN), then compared with a reference voltage (1.5V) via a
current amplifier, resulting in PWM drive outputs to All Bridge switches.
2.1.2）Protection Circuit
7
Service Manual
Over Voltage Protection and over-current protection are monitored by the voltage on VSEN(Pin
1) During normal operation , if a CCFL is damaged or removed ,the voltage at VSEN (Pin1)
increases .Once the voltage at VSEN exceeds 3.0V (OVPT Setting) the driver output duty cycle is
regulated and the shutdown delay timer is activated. OVPT set the overall protection threshold voltage
that is lower than 3V (VSEN threshold). Once the voltage at TIMER pin reached about 3v ,the IC will
shut down and latch . R3, R4,R14,R15,C1,C15,C16,C17 are connected in high voltage output
connector, the divided AC voltage is inverted DC voltage through D2, D3, R9 and C11 are used to
rectify wave & dump noise. Then the voltage signal reaches Pin1 VSEN of U1, when the voltage
changes, build-in PWM of U1 will adjust output voltage.
Open Lamp Protection: In normal operation, R10,R11 are sensed a high level DC voltage,If a
CCFL is removed or damaged during normal ,the voltage at SSTCMP(Pin2) rises rapidly .when the
voltage at SSTCMP reaches a threshold of approximately 2.0V,a current source charges the
capacitor(C3 and C18)connected to TIMER(Pin12).Once the voltage level at the TIMER pin reaches a
threshold of approximately 3.3v,The drive outputs shut down and latch .
2.2 Power PWM circuit

2.2.1) Block diagram:(fig.4)
EMI Filter Rectifier and Isolation power Rectifier and filter Inverter circuit
filter transformer
PWM controller Switching element Rectifier and filter
Interface
circuit
Feedback Isolation
2.2.2) AC Input and EMI Filter:(fig.5)
fig.5
CN850 is a connector for connecting AC Power. F850 is a fuse to protect all the circuit AC. Input
8
Service Manual
voltage is from 90V to 264V. R850/R851/R852 are joined between two inputting main circuit to prevent
man from shock. L850 is used to filter low frequency noise. C850 and C851 are used to discharge the
noise that L850 produced. High frequency waves are damped by C852;
2.2.3)High Voltage to Low Voltage Control Circuit:(fig.6)
fig.6
D850 is a rectifier in which there are 4 build-in diodes, inverting AC to DC.
C854 is used to smooth the wave from rectifier. U850 is a highly integrated PWM controller.
Typical start-up current for U850 is only 20 uA, When current flow through R841/R842/R843 gets to
Pin 3of U850, with VDD hold-up capacitor C855, U850 is enough for starting up.
When U850 begins to operate Pin8 of U850 will output square wave to drive Q850, then the main
current flow get to GND bypassing through T850, Q850. Because of the change of current flow, wires in
the other side of T850 will induct current. In the same time, the current inducted by wires which
connected T850 Pin 1 and Pin 3, with components of D852, R856and C855 ,will be supplied to U850 for
normal operating.
9
Service Manual
When the sense voltage across the sense resistor R859, reaches the threshold voltage around 0.85v,
the output GATE drive will be turned off. Every time when the output of power supply is shorted or over
loaded, the FB voltage will increase, the build-in PWM output will then be turned off. Both of two will
prevent the power supply from being overheated under over loading condition. The PWM duty cycle is
determined by this current sense signal and VFB, the feedback voltage, when the voltage on sense pin
reaches V-(PWMcopm) =(Vcomp-2VF)/3, A switch cycle will be terminated immediately, Vcomp is internally
clamped to a variable voltage around 0. 85 V for output power limit
When Q850 are turned off, the main current flow will be consumed through D851, C875,
R853/R854/R855 and D853, This will prevent Q850 from being damaged under large current impulse and
voltage spike.
2.2.4)DC_27V and 5V Output Circuit and Feedback circuit:(fig.7)
fig.7
D854/D855 is used to rectify the inducted current. C862 is used to store energy when current is
reversed. The parts including C863 are used to smooth the current waves that are from D854/D855, then
27V voltage is supplied;
D860 is used to rectify the inducted current. R861 and C873 are used to store energy when current is
reversed. The parts including C866, C867, C868, and L854 are used to smooth the current waves that are
from D860, then 5Vvoltage is supplied;
27V and 5V supply voltage feed back to PWM controller U850 via R871, R872, R868 and
I850,I851.R860,C859 and C871 used to control respond time.
10
Service Manual
2.3 I/F Board Circuit (see the Attachment 2- Schematic)
2.3.1 RGB CAPTURE
- Signal RED,GREEN,BLUE input through CN102 #1,#2,#3, Stop DC via C113, C114 and C115, and
then enter into U105 (TSUMU58EHJ-LF-2) analog input PIN #28,#25,#23, and then
TSUMU58EHJ-LF-2 deals with signal internally. D103, D104, D105 are ESD protector to prevent
U105 from ESD.
- Signal DDC_SCL (series clock) inputs via CN102#15, and then passes through ZD106 for ESD
protection, goes into EDID EEPROM IC U103 #6.
- Signal DDC_SDA (series data) inputs via CN102#12, and then passes through ZD103 for ESD
protection, goes into EDID EEPROM IC U103 #5.
- Signal TTL vertical sync. (Vsync) inputs via CN102 #14, and then clamped by ZD105 Zener, passes
through R134, and then goes into IC U105 (TSUMU58EHJ-LF-2) #33.
- Signal TTL horizontal sync. (Hsync) inputs via CN101 #13, and then clamped by ZD102 Zener,
passes through R133, and then goes into IC U105 (TSUMU58EHJ-LF-2) #32.
- CN101#5 is defined as cable detect pin, this detector realize via R121 and U104#36, and D102 is
ESD protector.
- U103 +5V is supplied by PC via CN102#9 with ZD102 for ESD protection, or supplied by Monitor
self via D106
- U103 is an EEPROM IC which is memory and EDID data saved in it.
2.3.2 DVI CAPTURE
- Differential Signal input RX0+,RX0-,RX1+,RX1-,RX2+,RX2-,RXC+,RXC- through CN201
#18,#17,#10,#9,#2,#1,#23,#24 via R206,R205,R204,R203,R202,R201,R207,R208 enter into U105
(TSUMU58EHJ-LF-2) Digital input terminal #16,#15,#13,#12,#10,#9,#18,#19, and then
TSUMU58EHJ-LF-2 deals with signal internally. D206, D207, D204, D205, D202, D203, D208,
D209 are ESD protector to prevent U105 from ESD
- Signal DDC_SCL (series clock) inputs via CN201#6, and then passes through ZD204 Zener for ESD
protection, via R209, goes into EDID EEPROM IC U201 #6.
- Signal DDC_SDA (series data) inputs via CN201#7, and then passes through ZD203 Zener for
ESD protection, via R210, goes into EDID EEPROM IC U201 #5.
- CN201#15 is defined as cable detect pin, this detector realize passes through R216 ,go into U105#49,
and D210 is ESD protector.
- U201 +5V is supplied by PC via CN201#14 through D201, or supplied by Monitor self via D201.
- U201 is an EEPROM IC which is memory and DVI input EDID data saved in it.
2.3.3 Buttons Control
- Button “Power” on front bezel connects to U105 (TSUMU58EHJ-LF-2) #4 through CN104 #8, U105
#4 is defined as power on/off.
- Button “+” on front bezel connects to U105 (TSUMU58EHJ-LF-2) #120 through CN104 #2,
U105#120 Voltage is defined as “Plus”.
- Button “-” on front bezel connects to U105 (TSUMU58EHJ-LF-2) #121 through CN104 #3, U105
#121 Voltage is defined as “Minus”.
- Button “Menu” on front bezel connects to U105 (TSUMU58EHJ-LF-2) #50 through CN104 #1,
U105 #50 Voltage is defined as “Menu”.
- Button “SELECT” on front bezel connects to U105 (TSUMU58EHJ-LF-2) #122 through CN104 #4,
U105 #122 Voltage is defined as “SELECT”.
- LED Indicator on Front Bezel
a. When press button “power”, U105 (TSUMU58EHJ-LF-2) #123 be send in low Voltage, make
Q107#3 sends out high Voltage , and then to CN01#5 on keypad, LED green on.
b. When in “Suspend” mode, U105 (TSUMU58EHJ-LF-2) #124 sends out a low Voltage, make
Q108#3 sends out high Voltage and then to CN01 #7 on keypad, LED Amber ON.
2.3.4 MATAR CHIP U105 (TSUMU58EHJ-LF-2)
- U105 (TSUMU58EHJ-LF-2) #91~#100 output 8 bit even and #77~#86 output 8 bit odd LVDS digital
data to panel control circuit through CN103.
11
Service Manual
- U105 (TSUMU58EHJ-LF-2) #73 output PPWR ”H” potential to make Q104 conducted, and then
make Q101 conducted, +5V flow to CN103#1~#3 as Panel Vdd .
- U105 (TSUMU58EHJ-LF-2) #109 output CCFL_ON/OFF ”L” potential to control Inverter on/off.
- U105 (TSUMU58EHJ-LF-2) #125 outputs Brightness “PWM” signals to control CCFL brightness.
- TCLK by Crystal 14.318MHz input to U105 (TSUMU58EHJ-LF-2) #128/#127.
- U105 (TSUMU58EHJ-LF-2)#108 is RESET signals input pin
Please refer to U105 (TSUMU58EHJ-LF-2) Pin Assignments table in page

2.3.5 Regulator Circuit
- +3.3V is generated from Regulator U101 which is supplied by+5V via R101 and through C104
filtering,
-+1.8V is generated from Regulator U102 which is supplied by+3.3V through C106 filtering,
3. FACTORY PRESET TIMING TABLE
Standard Resolution Horizontal Frequency Vertical Frequency (Hz)
(KHz)
720 x 400 31.469 70.087
640 x 480 31.469 59.940
640 x 480 37.500 75.000
800 x 600 37.879 60.317
800 x 600 46.875 75.000
VESA 1024 x 768 48.363 60.004
1024 x 768 60.023 75.029
1152 x 864 67.500 75.000
1280 x 1024 64.000 60.000
1280 x 1024 79.976 75.025
1680 x 1050 65.160 60.0
IBM DOS 720 x 400 31.469 70.087
4. Power On/Off Sequency

Hardware power On/Off
When power cord plug into AC socket, Power provides 26V and DC_5V.
DC_5V is main voltage for panel and Regulator U101.
DC_3.3V is coming from Regulator U101, DC_3.3v is main voltage for U105. When DC_3.3V input to
U105 and U105 reset circuit active, U105 all registers will be set to default, that means finish hardware
power on.
When pull out power cord from AC socket,the system shut down instantly for no supply
Software power On/Off

- When press power key, U105 #4 receives low pulse, then U105 (TSUMU58EHJ-LF-2) will be wake
up and send control signals(at 73,109pin) to on CCFL and switch 5.0v to panel module, at the same
time,U105 make the VGA/DVI cable input signal source display normal on panel if the VGA/DVI
cable input signal is active
- If power ON, U105 #123 (LED_blue) will send out low potential, and then LED blue on.
- If power saveing, U105 #124 (LED_Amber) will send out low potential, and then LED Amber on.
- If power ON or power saveing, when press power key, U105 #4 receives low pulse, then U105 will be
sleeping and turn off backlight, at the same time, the panel will lose +5V.
The Panel_Vcc, Backlight_En, CLK/DATA output to panel will follow the following sequency.
12
Service Manual
Power supply for panel+5V VDD

90% 90%
10%
0V 10%
T1 T2
T5 T6 T7
Signals Valid data

(Digital RGB, HS, VS, DE, CLOCK)
0V
T3 T4
Power supply for backlight
T1(ms) T2 (ms) T3 (ms) T4 (ms) T5 (ms) T6 (ms) T7(ms)

SPEC(Samsung) 0.3~10 0.0~50 >500 >100 0.0~50 NA >1000
SPEC (INL) 0.1~10 0.0~50 >200 >100 0.0~50 >0.1 >1000
5. D-SUB Connector Pin Assignment
Pin Symbol Pin Symbol Pin Symbol

1 Red 6 Red_GND 11 GND
2 Green 7 Green_GND 12 DDC_SDA
3 Blue 8 Blue_GND 13 Hsync
4 GND 9 PC+5V 14 Vsync
5 Cable Detect 10 GND 15 DDC_SCL
6. AC Outlet Pin Assignment
Pin Symbol
1 Line
2 GND
3 Neutral
7. Inner Connector Pin Assignment

7.1 CN103 (Connect M/B to Panel,)
Pin Symbol Description
1 Panel_Vcc Panel power supply (typ.5.0V)
2 Panel_Vcc Panel power supply (typ. 5.0V)
3 Panel_Vcc Panel power supply (typ. 5.0V)
4 NC
5 NC
6 NC
13
Service Manual
7 GND_LVDS LVDS Ground
8 RXE3+ LVDS signal of even channel 3(-)
9 RXE3- LVDS signal of even channel 3(+)
10 RXEC+ LVDS signal of even channel clock (+)
11 RXEC- LVDS signal of even channel clock (-)
12 RXE2+ LVDS signal of even channel 2(+)
13 RXE2- LVDS signal of even channel 2(-)
15 RXE1+ LVDS signal of even channel 1(+)
16 RXE1- LVDS signal of even channel 1(-)
18 RXE0+ LVDS signal of odd channel 0(+)
19 RXE0- LVDS signal of odd channel 0(-)
20 RXO3+ LVDS signal of odd channel 3(+)
21 RXO3- LVDS signal of odd channel 3(-)
22 RXOC+ LVDS signal of even channel clock (+)
23 RXOC- LVDS signal of even channel clock (-)
25 RXO2+ LVDS signal of even channel 2(+)
26 RXO2- LVDS signal of even channel 2(-)
27 RXO1+ LVDS signal of even channel 1(+)
28 RXO1- LVDS signal of even channel 1(-)
29 RXO0+ LVDS signal of odd channel 0(+)
30 RXO0- LVDS signal of odd channel 0(-)
7.2 CN1, CN2, CN3, CN4 (Connect to Panel Backlight,)

1 HV High voltage for lamp
2 LV Low voltage for lamp
7.3 CN104 (Connect to keypad, WAFER2*4P or compatible connector)

1 MENU OSD “MENU” control
2 PLUS OSD “+” control and “Brightness/Contrast” adjustable hot key
3 MINUS OSD “-” control and “Auto adjust” adjustable hot key
4 SELECT OSD “input source Select” control
5 LED Blue LED Blue on/off control
6 GND Ground
7 LED Amber LED amber on/off control
8 POWER Ground
14
Service Manual
8. Key Parts Pin Assignments
U105(TSUMU58EHJ-LF-2)
15
Service Manual
16
Service Manual
17
Service Manual
8.1 U108 (Serial Flash)

Pin Symbol I/O Description
1 CE# I The device is enabled by a high to low transition on CE#. CE#
must remain low for the duration of any command sequence.
2 SO I/O To transfer commands, addresses, or data serially into the device.
3 WP# I/O The write protect (WP#) pin is used to enable/disable BPL bit in
the status register.
4 VSS G Connect ground
5 SI I/O To transfer commands, addresses, or data serially into the device
input are latched on the rising edge of the serial clock.
6 SCK I/O To provide the timing of serial interface.
Commands, addresses, or input data are latched on the rising
edge of the clock input, while output data is shifted out on the
Falling edge of the clock input.
7 HOLD I/O To temporarily stop serial communication with SPI flash
memory without resetting the device.
8 VDD P To provide power supply.
18
Service Manual
8.3 U850 (LD7552B, PWM Power Controller)
1 GND Ground
2 COMP I Voltage feedback pin(same as the COMP pin in
UC384X).By connecting a photo-coupler to close
the control loop and achieve the regulation.
3 VCC I Supply voltage pin
4 RT I This pin is to program the switching frequency. By
connecting a resistor to ground to set the switching
frequency.
5 NC Unconnected pin
6 CS I Unconnected pin
7 VCC I Supply voltage pin
8 OUT O Gate drive output to drive the external MOSFET
8.4 U1 (INL833, CCFL Inverter controller IC)
1 VSEN I Voltage sense Feedback
2 SSTCMP I Capacitor for soft-star and loop
compensation
3 CT I Timing resistor and capacitor for operation
and striking frequency
4 RT1 I Timing resistor for striking frequency
5 GNDA Signal Ground
6 PDR2 O High side Driver output2
7 GNDP Power Ground
8 NDR2 O Low side Driver output2
9 NDR1 O Low side Driver output1
10 PDR1 O High side Driver output1
11 VDDA I Input power Pin
12 TIMER I Timing capacitor for Delay Timer
13 PWM I External PWM Dimming Input
14 ISEN I Current sense feedback
15 OVPT I Over-voltage protection threshold voltage
16 ENA I IC Enable/Disable
19
Service Manual
Chapter 4- Disassembly & Assembly
1. Exploded Diagram
20
Service Manual
2. E2209WFPf Disassembly Block
Note: 1. The arrows point out the direction of disassembly.

21
Service Manual
3. Assembly Block
Note: 1. The arrows point out the direction of assembly
22
Service Manual
Chapter 5- TEST AND ADJUSTMENT
1. Function key Definitions
Menu
Enter
Power
Power Switch with power LED indicator Power: On/Off, includes power indicator and Power ICON
green- Active On
Amber- DPMS
Front Panel Controls 1- Input select: Select input signal
2- Menu: Call out OSD Menu and choose
3- (): symbol molded into button, calls out brightness/Contrast, move down
the highlight bar.
4-()symbol molded into button, move up the highlight bar
Hot Key Function Automatic adjust: Directly press “”
Brightness/Contrast Icon: Directly press “”

Factory Modes Keys Function Auto Color Balance
Purpose: Automatically calibrate chip ADC parameter by using chip internal

DAC.
Process: If we want to do “Auto Color Balance” again, please confirm the

following steps.
1) Connect the VGA cable with the standard video pattern generator and
display the pattern with blackest and whitest colors.
2) Press “Power Key”, to power off the monitor.
3) Press “Menu Key” and “Up Key” simultaneously, and then press
“Power Key” to power on the monitor.
4) Press “Plus Key”, choose “Auto color” at bottom
5) Then execute Auto Color item.
6) After the “Auto Color Balance” process finished, go back to the
submenu of “Other Settings”, and press “Factory Reset” to exit
23
Service Manual
Factory mode.
OSD Control
1st Level 2nd Level 3rd Level 4th Level 5th Level
Brightness
Contrast
Press √to adjust the screen
Auto Adjust(For VGA)
automatically
Auto Select
Input Source VGA
DVI-D
Input Color Format RGB YPbPr
Mode Selection Graphics Video
Preset Modes Standard
MultiMedia
Game
Warm
Cool
R
Custom(R,G,B) G
Color Settings B
Reset Color Settings
Horizontal Position
Vertical Position
Sharpness
Pixel Clock
Phase
Reset Display Settings
English
Español
Français
Language Deutsch
Português (Brasil)
简体中文
日本語
Other Settings Menu Transparency
Menu Timer
Menu Lock Lock Unlock
DDC/CI Enable Disable
LCD Conditioning Enable Disable
Factory Reset(Reset All
settings)
24
Service Manual
Factory Mode Introduction

With signal input, press “Power” button to turn off the monitor. Press “Menu” and “Auto/Plus” buttons together,
and then press “Power” button to turn on the monitor. After power on.Press “Plus Key”, enter Factory mode
(Fig.10).
Fig9
Fig10
Back: Exit from Factory mode and back to NO OSD Status.

Panel: The current-setting panel is highlighted.
Auto Color: Automatically calibrate chip ADC parameters by using internal DAC.
25
Service Manual
Burn In: Enable or disable the Burn-in mode by choosing ON or OFF.
Reset Timer: Reset the “Turn-on time” of the panel to 0H0M.
Color Temp: The R, G, B of Blue Preset (9300K), Red Preset (5700K) and Normal Preset (6500K) are generated
from scaling chip’s back-end white-balance program.
Time: Turn-on time of the panel.
DEBUG: Debug tool of scale IC U104.
Dell panel P/N

LCD supplier Panel Supplier P/N Dell P/N
Samsung 22”W LTM220M1-L01 MY228
INL 22”W MT220WW01-V0 D569C
CMO 22”W M220Z1-L03 P546G
Burn-in pattern
Burn-in pattern will self-generate automatically without VGA and DVI cable plugged in when the monitor set at
Burn-in on mode and burn-in pattern will not be stopped until plugging in the VGA cable. Exit Burn-in mode
method as followe: plugging in the VGA/DVI cable, press “Menu” button to call out OSD Main Menu, Press “Plus
Key”to select“Other Settings Menu”then pop submenu and choose Factory reset.
Auto Color Balance (Automatically calibrate chip ADC parameter by using chip internal
DAC.)
5.1 If it is a new-built set, press “Auto/Plus” button to execute “Auto Color” at standard video pattern
5-MOSAIC pattern
5.2 Please confirm the following steps to perform “Auto Color Balance”:
- Connect the VGA cable with the standard video pattern generator and display 5-MOSAIC pattern on the
monitor.
- Press “Power” button to power off the monitor.
- Press “Menu” and “Auto/Plus” buttons simultaneously; then press “Power” button to power on the
monitor.
- Press “Plus Key”, select“Other Settings Menu” ,then Press “Plus Key”and choose factory at bottom
- Set BurnIn Mode item to ON, then execute Auto Color item.
- After the “Auto Color Balance” process finished, go back to “Other Settings Menu”, and press “Factory Reset” to exit Factory
mode
Upgrade Firmware to Serial via Flash Cable by ISP_Tool V4.100.exe

7.1 Connect the monitor and PC follow Fig 11
26
Service Manual
Fig 11
※ The detailed reprogramming procedures will be described in ISP User's Guide.
After repair, to ensure the quality you should do the following test and adjustment.
27
Service Manual
Item Content Equipment
Test OSD 1.Signal is set as 1680×1050@60Hz under General-1 Chroma
function 2. LCM button are from left to right, checking whether each Signal Generator
single function key and compound function key can be worked.
Contrast Check 1. Set input mode to 1680×1050@60Hz Chroma

2. Set to 32gray scale pattern Signal Generator
3. Set contrast to the maximum. At most 6 bars cannot be
distinguished.
Color 1. Do “Auto color Balance” at 1680×1050@60Hz, 32gray Chroma Signal
Temperature scale pattern Generator and color
2. Measure color temperature, check if it complies with the analyzer
following temperature :
Warm x=0.328 +/- 0.03, y=0.344+/-0.03
Desktop x= 0.313 +/- 0.03, y=0.329+/-0.03
Cool x= 0.283 +/- 0.03, y=0.298+/-0.03
1. Use Chroma Pattern Generator to make sequence. Chroma
Modes switching VESA (640x480 800x600 1024x768 1152x864 1280x1024 Signal Generator
check 1680×1050@60Hz ), the detail supported modes (see table 1)
and power saving signal.
2. Confirm the above timing modes must be full screen and
the picture must be normal.
3. LED is amber at power saving mode.
VGA cable When select VGA model and VGA cable is not plugged out, Visual check
detector self-test OSD will be floated.
Y measurement 1. Set brightness and contrast to default value 75 at 6500K Chroma Signal
at default setting 2. With full white pattern, Y shall be 220 20 cd/m2 Generator and Color
Analyzer
OSD Lock Test Soft Lock: When OSD is locked, this icon should appear for only Visual Inspection
2 seconds with all buttons pressed, except for the “Menu” and
“Power” ones.
Hard Lock: Press “Menu” button for 15 seconds enables the
“locked” icon to be displayed, which will lock All buttons
expect for the “Power”. Press “Menu” button for another 15
seconds enables the “unlock” icon to be shown.
Panel Flicker 1. Mode:1680×1050@60Hz Equipment::
check 2. Set Brightness& Contrast to default value (75%) Chroma Signal
3. Do “Auto Adjustment” Generator & PC
4. Shut down PC to check whether there’s flicker on the
center of the picture.
Power saving 1. Mode:1680×1050@60Hz Chroma signal
2. Pattern: full Black generator and
3. Brightness: Max. Power meter
4. Contrast: Default AC input:230V/50Hz
5. Check power consumption at each modes
State Power Consumption LED color
Normal(with full
＜46Ｗ blue
load)
Stand By ＜2Ｗ amber
Power Key Off
＜1Ｗ no
28
Service Manual
Chapter 6- TROUBLE SHOOTING
Common Acknowledge
 If you change the M/B, be sure that the U101,U102 and U105 these three components also changed to
the new M/B because there was program inside. If not, please re-write EDID or upload firmware into
serial flash(U105) via VGA Cable. How to do please refer to the Page 19.
 If you adjust clock and phase, please do it at condition of Windows shut down pattern.
 Please confirm the R/G/B color under 32gray scale pattern.
 This LCM is analog interface. So if the entire screen is an abnormal color that means the problem
happen in the analog circuit part, if only some scale appears abnormal color that stand the problem
happen in the digital circuit part.
 If you check the H/V position, please use the crosshatch pattern.
 This LCM support 10 timing modes, if the input timing mode is out of specification, “Cannot Display
this Video Mode” will be displayed on the screen.
 If brightness uneven, repairs Inverter circuit or change a new panel.
 If you find the vertical line or horizontal line lost on the screen, please change panel.
 If the self-test pattern is moving on the screen, please check whether VGA Cable is plugged in the
Monitor or PC if select analog model on OSD or check whether DVI Cable is plugged in the Monitor
or PC if select DVI model on OSD . If the VGA or DVI Cable is plugged in well, please change
another VGA or DVI cable.
No Power and LED Off
Is there DC24V output
Is there DC5V at L854;
NO
Is the voltage at C854 in the

range of 127V~339V?
YES NO
Check RT850, F850
Is the voltage at pin4 of U850 312V?
YES NO Check F850
Is the voltage at pin6 of U850 0.9V?
YES NO
Check D852, D851
Is the voltage at pin6 of T850 120V?
YES
Check Q850
29
Service Manual
Power(include IF +5Vand +3.3V) supply normal but LED off and
no display
Is the key function OK? Yes Press power key to DC on the monitor,
if display ok the process is end, if no
NO display see the no backlight process
Is the frequency 14.318MHz at NO

#127,#128 of IF Board U105? Change crystal X101
Yes
NO Change C164
Is the low active reset signal at #108 of
IF Board U105 normal?
NO
Yes Yes Change U104
Is the serial clock signal at #6 of IF NO

Board U108 normal when power AC on? Change U108
Yes
Upgrade Firmware to Serial Flash U108
by VGA port with ISP_ Tool V4.100.exe
END
Power(include IF +5Vand +3.3V) supply and display normal only

LED off
Is the keypad cable connective OK NO
Reassembly or changing
Yes
Is LED at keypad work OK NO Change LED
Yes
yes
Is R165 open? Change R165
NO
NO
Is Q107 work normal? Change Q107
Yes
Is theLED control signal at 123# of U105
NO Change U105
high-low convertible when DC on/off
END
30
Service Manual
Power (include IF +5Vand +3.3V) supply and display normal but

LED Amber
Is Power LED Amber?
YES
NO
Do the Hsync. & Vsync. Signals exist Insert VGA Cable correctly
in CN102 #13& #14 separately when
select VGA mode by OSD?
YES
Do the Hsync. & Vsync. Signals exist NO

in R133 & R134? Check R133 & R134
YES
Do the Hsync. & Vsync. Signals exist NO

in U105#32& #33? Change R135 & R136
YES
Is the Q108 work normal NO

Change Q108
YES
Is theLED control signal at 4# of
U105 high-low convertible when DC Change U105
NO
on/off
END
31
Service Manual
4.Power (include IF +5Vand +3.3V) supply normal ,key function

OK,but backlight can’t be turned on
No backlight
Yes
No No power supply to Yes Check the cable that from I/F
LED lamp is OK inverter BD to P/I BD is ok
Yes
Is there 27V Voltage on No No

Q6, Q7 Check power supply
Pin 7,8 & 13,14 of T1
fail
Yes
Yes Replace Q6, Q7
Is there PWM signal on No

Pin13 of U1 Check I/F BD
Yes
Is there High level voltage No

on Pin16 of U1 Check I/F BD
Yes
Yes
Vsense voltage is 2.9V Lamp connector opened
No
Are there PWM signal on No

pint on Pin12 of U1 U1 Failure
Yes
Yes Yes
Pin14 of U1 Voltage Check R21,R22,C10
is Low Level Feedback circuit failure
Yes Yes
Pin6&10 of U1 voltage is U1 protected Check ZD1, R1 , ZD2, R2, C12, C13
high level voltage
Yes
END
32
Service Manual
5. Backlight on, key function and LED accurate indication ok but
no picture
Backlight on ,key function and LED

accurate indication ok but no picture
YES
YES
IS the display is white and cannot Check DC 5.0V on NO Is the panel enable
display OSD when press key? CN103#1, #2, #3 signal at 73# of
U105,if no check
Q104 circuit or change
NO U105,if yes Check
Q101 circuit
VGA
Is display selftest picture at Is there RGB signal in NO
VGA mode or DVI mode? U104 #28, #25 #23? Change D103,
D104 & D105
DVI
Yes
Is there DVI signal in U105 #9, YES Are there data output on YES Is the FFC cable
#10,#12,#13,#15,#16,#18 #19? U105#77~#86 inserting ok,if no
#91~#100 reinsert else
change FFC cable
No
Change U105
Change D202, D203, D204,
D205, D206, D207, D208,
D209
END
33
Service Manual
6.At 32-gray scale pattern, color lost in some scale
Color lost in some scale at 32-gray scale pattern
OK,
Re-insert the FFC Cable END
NO
OK,
Change FFC Cable END
NO
Change U105
34
Service Manual
Chapter 7- RECOMMENDED PART LIST
Content PN Description Supplier Usage
412000628810R IC LD7552BPS SOP8（Leadtrend)ROHS LEADTREND, 1
412000654630R IC INL833GN SOP16(O2 MICRO)Rohs O2, 1
426000091010R XFMR SW DIP ERL28 PC40 550uH SPW-101 RoH FOXCONN,FRONTIER,LISHIN,MEIKAI, 0
426000091160R XFMR SW DIP EEL22 P4 4.16H SPW-116 ROHS DARFON,FOXCONN,HUALON,LISHIN, 1
PI BD 420431014083R CAP SEK 100uF/450V M,105℃ CF 18x40(2.5) ELITE,SAMXON,SU'SCON, 0
410500059290R XSTR AP2761I-A N-CH TO-220CFM ADVANCED P APEC 1
410050103050R XSTR FMA09N65GX N-CH TO-220F(FUJI) RoHS FUJI 0
410050057280R XSTR STP8NK80ZFP N-CH TO220FP (ST) ST 0
491571400100H PCB,P/I ,1/OSP /CEM1/16,LE22F4-612 HSIANGKUO,TAT CHUN, 1
412000653060R IC TSUMU58EHJ-LF-2 PQFP128(MSTAR)Rohs E MSTAR 1
412000494190R IC SST25LF020A-33-4C-SAE SOIC8(SST)ROHS SST, 1
412000494310R IC PM25LV020-100SCE SOIC8(PMC)RoHS PMC, 0
412000224482R IC AT24C16BN-SH-T 16K(ATMEL) SOIC 8 ROHS ATMEL, 1
412000224280R IC M24C16-WMN6TP SO8 16K (ST) ROHS ST, 0
412000481990R IC CAT24C16WI-TE13 SOIC-8(CATALYST)RoHS CATALYST, 0
412000332020R IC LD1117AL-3.3-A TO-252(UTC)RoHS UTC, 1
IF BD 412000332130R IC AP1117D33LA 3.3V (ANACHIP) TO-252-3L, ANACHIP, 0
412000332830R IC AS1117R-3.3.TR-LF,TO-252(A1 SEMI)RoHS A1SEMI, 0
412000330020R IC LD1117AL-1.8V-A SOT223(UTC) RoHS UTC, 1
412000330830R IC AS1117L-1.8/TR-LF,SOT223(A1 SEMI)RoHS A1SEMI, 0
412000330070R IC AZ1117H-1.8 SOT223(AAC)RoHS BCD, 0
412000435481R IC AT24C02BN-SH-T 2K SOIC8(ATMEL)RoHS ATMEL, 1
412000480280R IC M24C02-RMN6TP SO8(ST)RoHS ST, 0
412000480990R IC CAT24C02WI-TE13 SOIC-8(CATALYST)RoHS CATALYST, 0
35
Service Manual
ATTACHMENT 1- Bill of Material
1. Interface board BOM
2E+07
ITEM P/N Description Supplier Usage Location
791701300B00R PCBA,I/F BOARD W/O SPK,LE22F4-B12 ROHS
10 629030018710R PROGRAM,W/O SPK LE22F4-B12 ROHS 1
20 791701320600R PCBA,I/F BOARD,MI,W/O SPK,LE22F4-612 ROH 1
30 791701340600R PCBA,I/F BOARD,SMT,W/O SPK,LE22F4-612 RO 1
40 511130001200R SOLDER BAR,Sn96.5/Ag3.0/Cu0.5/Ni0.06/Ge0 TOMAS, 2.2
50 641120000010R HDCP RECEIVE DEVICE KEY DCP LLC, 1
LABEL,BARCODE,BLANK,33x7mm, ROHS,FOR
60 506140005700R HENGMINGDA,JIAYINMEI,KAIDA, 1
PCB
2E+07
791701320600R PCBA,I/F BOARD,MI,W/O SPK,LE22F4-612 ROH
10 430631080170R WFR 8P 2.0MM 180° W/LOCK ROHS CVILUX,FOXCONN,JOWLE, 1 CN101,
20 440819015030R CON D-SUB FEM.15P RA W/O SCREW DZ11AA1-H CVILUX,DLK,FOXCONN,JOWLE,TEKCON,ZJGHJ, 1 CN102,
30 430631080180R WFR 2X4P 2.0MM 180° W/LOCK ROHS CVILUX,FOXCONN, 1 CN104,
40 443842024060R CON DVI-D RA 24+1P FEM.W/O SCR EW QH1112 DLK,FOXCONN,ZJGHJ, 1 CN201,
50 432008010270R XTAL 14.31818MHz HC-49US DIP 16pF 30PPM HUAN MOUN,TXC,ZGC, 1 X101,
60 420271010460R CAP SE 100uF 16V M,105℃ ST,6.3*11 ROHS SAMXON,SU'SCON,TEAPO, 2 C109,C102,
70 420432200460R CAP EC 22uF 16V M,105℃ ST, 5x11,RoHS ELITE,LELON,SAMXON,SU'SCON,TEAPO, 3 C103,C142,C150,
2E+07
791701340600R PCBA,I/F BOARD,SMT,W/O SPK,LE22F4-612 RO
10 444099030040R CON, SMD 1.0MM 30PIN with lock RoHS CVILUX,P-TWO, 1 CN103,
C106,C108,C110,C126,C128,C133,C134,C135,C136,
C137,C138,C139,C140,C141,C143,C144,C145,C146,
C147,C149,C153,C154,C155,C156,C159,C160,C161,
20 419351044010R C SMD(0402) X5R 0.1uF/16V K,RoHS DARFON,WALSIN,YAGEO, 53
C165,C167,C168,C169,C170,C171,C172,C173,C201,
C202,C213,C111,C122,C123,C124,C125,C203,C204,
C205,C206,C207,C208,C209,C210,C211,C212,
30 419311054070R C SMD(0805) X7R 1uF/16V K RoHS REV:A DARFON,MURATA,TDK,WALSIN, 2 C112,C164,

40 419314734010R C SMD(0402) X7R 0.047uF/16V K,RoHS DARFON,WALSIN,YAGEO, 7 C113,C114,C115,C119,C120,C121,C152,
50 419302700510R C SMD(0402) NPO 27PF/50V J RoHS DARFON,MURATA,TDK,WALSIN,YAGEO, 2 C130,C129,
60 419351054060R C SMD(0603) X5R 1uF/16V K,RoHS DARFON,MURATA,SAMSUNG,TDK,WALSIN,YAGEO, 1 C148,
70 419302200510R C SMD(0402) NPO 22PF/50V J,RoHS DARFON,MURATA,TDK,WALSIN,YAGEO, 2 C157,C158,
D102,D103,D104,D105,D202,D203,D204,D205,D206,
80 411020026210R DIO BAV99 350mW 70V SOT-23(PHI RoHS PHILIPS, 13
D207,D208,D209,D210,
80 411020026090R DIO BAV99 350mW 75V SOT-23(PEC RoHS PANJIT, 0
80 411020026020R DIO BAV99-LF 350mW 70V SOT-23 (FEC)RoHS FRONTIER, 0
90 411020047210R DIO BAV70 85V SOT23 (PHILIPS) RoHS PHILIPS, 2 D106,D201,
90 411020047090R DIO BAV70, 70V SOT-23(PEC) ROHS PANJIT, 0
90 411020047020R DIO BAV70-LF, 70V SOT-23(FEC) ROHS FRONTIER, 0
100 432002312144R BEAD CORE SMD(0603)120Ω 300mA SBK160808 CHILISIN,TAI-TECH, 1 FB101,
110 432002360140R BEAD CORE SMD(0603)60Ω 600mA, GBK160808 CHILISIN,TAI-TECH, 2 FB102,FB105,
120 410500068290R XSTR AP2305GN P-CH SOT23(APEC) RoHS APEC, 1 Q101,
120 410500075270R XSTR AO3415 P-CH,SOT23(AOS) RoHS AOS, 0
120 410060018380R XSTR AM2321P-T1-PF P-CH SOT23(ANALOG POW AP, 0
130 410500045210R XSTR PMBT3904 NPN 200MA,40V SOT23(PHILIP PHILIPS, 3 Q104,Q201,Q103,
130 410500045140R XSTR MMBT3904LT1G NPN 200MA 40V SOT23(ON ON SEMI, 0
130 410500045090R XSTR MMBT3904 NPN SOT-23(PANJIT)RoHS PANJIT, 0
140 410500046210R XSTR PMBT3906 PNP 200MA,40V SOT23(PHILIP PHILIPS, 2 Q107,Q108,
140 410500046090R XSTR MMBT3906 PNP SOT-23(PANJIT)RoHS PANJIT, 0
140 410500046180R XSTR MMBT3906LT1G PNP 200mA 40V SOT23(ON ON SEMI, 0
150 414904000050R RES SMD (1206) 0Ω J,RT RoHS REV:A TA-I,WALSIN,YAGEO, 2 R101,R113,
160 414916000050R RES SMD (0603) 0Ω J,RT RoHS TA-I,WALSIN,YAGEO, 4 RB101,RB102,RB103,R164,
R102,R129,R140,R150,R151,R152,R166,R169,R171,
170 414918010350R RES SMD (0402) 10KΩ J,RT,RoHS TA-I,WALSIN,YAGEO, 24 R172,R174,R176,R177,R178,R179,R180,R190,R192,
R213,R217,R103,R220,R184,R161,
180 414918000050R RES SMD (0402) 0Ω J,RT,RoHS TA-I,WALSIN,YAGEO, 3 R121,R147,R148,

R105,R110,R127,R128,R137,R138,R188,R211,R212,
190 414918047250R RES SMD (0402) 4.7KΩ J,RT,RoHS TA-I,WALSIN,YAGEO, 10
R219,
200 414918010450R RES SMD (0402)100KΩ J,RT,RoHS TA-I,WALSIN,YAGEO, 4 R107,R109,R106,R175,
210 414918047350R RES SMD (0402) 47KΩ J,RT,RoHS TA-I,WALSIN,YAGEO, 1 R108,
220 414918750910R RES SMD (0402) 75Ω F,RT,RoHS TA-I,WALSIN,YAGEO, 9 R117,R118,R119,R114,R115,R116,R122,R123,R124,
230 414918047150R RES SMD (0402) 470Ω J,RT,RoHS TA-I,WALSIN,YAGEO, 1 R159,

R130,R133,R134,R145,R146,R153,R154,R155,R160
240 414918010250R RES SMD (0402) 1KΩ J,RT,RoHS TA-I,WALSIN,YAGEO, 15
R191,R214,R125,R216,R157,R158,
250 414918010150R RES SMD (0402) 100Ω J,RT,RoHS TA-I,WALSIN,YAGEO, 6 R131,R132,R142,R143,R209,R210,
260 414918022250R RES SMD (0402) 2.2KΩ J,RT,RoHS TA-I,WALSIN,YAGEO, 2 R135,R136,
270 414918390010R RES SMD (0402) 390Ω F,RT,RoHS TA-I,WALSIN,YAGEO, 1 R144,
280 414916033150R RES SMD (0603) 330Ω J,RT RoHS TA-I,WALSIN,YAGEO, 1 R165,
290 414918010050R RES SMD (0402) 10Ω J,RT,RoHS TA-I,WALSIN,YAGEO, 8 R201,R202,R203,R204,R205,R206,R207,R208,
300 412000332130R IC AP1117D33LA 3.3V (ANACHIP) TO-252-3L, ANACHIP, 1 U101,

300 412000241550R IC AME1117CCCTZ 3.3V,TO-252(AM E)RoHS AME, 0
300 412000332020R IC LD1117AL-3.3-A TO-252(UTC)RoHS UTC, 0
300 412000332830R IC AS1117R-3.3.TR-LF,TO-252(A1 SEMI)RoHS A1SEMI, 0
310 412000330020R IC LD1117AL-1.8V-A SOT223(UTC) RoHS UTC, 1 U102,
310 412000330830R IC AS1117L-1.8/TR-LF,SOT223(A1 SEMI)RoHS A1SEMI, 0
310 412000330070R IC AZ1117H-1.8 SOT223(AAC)RoHS BCD, 0
310 412000598490R IC MT11171.8A SOT223(Matrix) RoHS MATRIX, 0
36
Service Manual
320 412000435481R IC AT24C02BN-SH-T 2K SOIC8(ATMEL)RoHS ATMEL, 2 U103,U201,
320 412000480280R IC M24C02-RMN6TP SO8(ST)RoHS ST, 0
320 412000480990R IC CAT24C02WI-TE13 SOIC-8(CATALYST)RoHS CATALYST, 0
330 412000653060R IC TSUMU58EHJ-LF-2 PQFP128(MSTAR)Rohs MSTAR, 1 U105,
340 412000224482R IC AT24C16BN-SH-T 16K(ATMEL) SOIC 8 ROHS ATMEL, 1 U106,
340 412000224280R IC M24C16-WMN6TP SO8 16K (ST) ROHS ST, 0
340 412000481990R IC CAT24C16WI-TE13 SOIC-8(CATALYST)RoHS CATALYST, 0
350 412000494190R IC SST25LF020A-33-4C-SAE SOIC8(SST)ROHS SST, 1 U108,
350 412000494310R IC PM25LV020-100SCE SOIC8(PMC)RoHS PMC, 0
ZD102,ZD103,ZD104,ZD105,ZD106,ZD201,
360 411130962950R ZENER 6.2V MMSZ5234B SOD-123(PANJIT)RoH PANJIT, 9
ZD203,ZD204,ZD107,
360 411121462950R ZENER 6.2V BZT52-C6V2 SOD-123(WILLAS)ROH WILLAS, 0
360 411131562950R ZENER 6.2V BZT52C6V2-7-F SOD-123(DIODES) DIODES, 0
370 491351300100H PCB I/F BOARD LE19H0 TIP TOP,WELFARE, 1
380 414916056150R RES SMD (0603) 560Ω J,RT RoHS REV:A TA-I,WALSIN,YAGEO, 1 R168,
2. power board BOM

791701400600R PCBA,P/I BOARD W/O SPK,LE22F4-612 ROHS
10 430637020030R WFR. 2P P=3.5mm 90°W/LOCK,RoHS CVILUX,FCN,FOXCONN, 4 CN1,CN2,CN3,CN4,
20 440149000350R SKT AC 10A/250V U/C/V, H 1.0MM ROHS TECX, 1 CN850,
HRN ASS'Y 8P 130mm UL1007 24 AWG
30 430300801650R FOXCONN,HEIGHTEN,JVE, 1 CN853,
ROHS
40 420424710510R CAP SD 470uF/50V M 105℃ F 13x21 RoHS LELON,SAMXON,SU'SCON,TEAPO, 2 C20,C863,
50 418103051920R CAP CD NPO 3pF 3KV D,S7.5, RoHS JNC,SUCCESS(SEC), 4 C21,C22,C23,C24,
50 418103058920R CAP CD SL 3pF 3KV D,S7.5,RoHS JNC,SUCCESS(SEC), 0
60 418105051920R CAP CD NPO 5pF 3KV D,S7.5, RoHS JNC,SUCCESS(SEC), 2 C25,C27,
CAP MEY 2200pF 250V M Y2 Y5V P=7.5mm
70 416202223610R JNC,POE,SUCCESS(SEC),TDK, 2 C850,C851,
RoH
CAP MEY 2200pF 250V M Y2 Y5V,W /O
70 416202223620R JNC,POE,SUCCESS(SEC), 0
FORMIN
80 416194743011R CAP MEX 0.47uF 275V K X2,F15 RoHS ARCOTRONIC,EUROPTRONIC,HJC,SCC, 1 C852,
90 420431014083R CAP SEK 100uF/450V M,105℃ CF,18x40(2.5) ELITE,SAMXON,SU'SCON, 1 C854,

CAP MEY 3300pF 250V M Y1,F10mm W/O
100 416213323620R JNC,POE,SUCCESS(SEC), 1 C860,
FORMI
110 416304723510R CAP PP 0.0047uF 250V J,F7.5 RoHS EUROPTRONIC,HJC,SCC, 1 C875,
120 415502438551R RES NKNP 2W 0.43Ω J, MINI,HK15,ROHS FUTABA,QUEENMAO,TZAI YUAN, 1 R859,
130 415350511550R RES MOF 2W 510Ω J,MINI HK15,ROHS FUTABA,QUEENMAO,TZAI YUAN, 1 R888,
140 432009400701R NTC 5Ω 4A 10ψ P=5mm, F RoHS THINKING,UPPERMOST, 1 RT850,
150 426000050070R CHOKE L-FILTER 12mH LIN-007 ET-20,RoHS DARFON,FOXCONN,LISHIN,MEIKAI,TDK, 1 L850,
CHILISIN,DARFON,EASYMAGNET,
160 425000010530R COIL CHK 5uH 7.8X10 CHK-053 0 181085R0L 2 L854,L856,
FOXCONN,FRONTIER,TAICHANG,
170 411050012010R DIO BRDG GBU405 600V/4A(TSC)RoHS TSC, 1 D850,

170 411050012020R DIO BRDG GBU4-06-BF52 600V/4A(FEC)RoHS FRONTIER, 0
180 411030068020R DIO SF50-04F69-LF 400V/5A DO-201AD(FEC)R FRONTIER, 2 D854,D855,
DIO SF55PT-F 400V/5A
180 411030068450R CHENMKO, 0
DO-201AD(CHENMKO)RO
DIO SF50GG-E1 400V/5A
180 411030068520R LITEON, 0
DO-201AD(LITEON)R
XFMR SW DIP EEL22 P4 800uH SPW-116
200 426000091160R DARFON,FOXCONN,HUALON,LISHIN, 1 T1,
ROHS
XFMR SW DIP ERL28 PC40 550uH SPW-101

210 426000091010R FOXCONN,FRONTIER,LISHIN,MEIKAI, 1 T850,
RoH
IC LTV817M-PR VDE (LITE-ON) P=10mm
220 412140002380R LITEON, 1 I850,
RoHS
240 735110007800R ASSY,H/S,Q850, LE19E6-812,ROHS 1
250 791701440600R PCBA,PWR&INV./B,SMD,LE22F4-612 ROHS 1
260 415350100550R RES MOF 2W 10Ω J,MINI,HK15, RoHS FUTABA,QUEENMAO,TZAI YUAN, 1 R861,
270 735110008100R ASSY,H/S,SRF10-10CT-LF,LE22F4 ,ROHS 1
37
Service Manual
FERR BEAD
280 432002200190R CHILISIN,TAI-TECH, 2 L857,L858,
3.5x9x0.65,VT,RoHS,RH03509ST-B
290 511130001200R SOLDER BAR,Sn96.5/Ag3.0/Cu0.5/Ni0.06/Ge0 TOMAS, 8.2
300 511110000103R HOT-MELT ADHESIVES,UB-618 U-BOND, 1.45
300 511110000101R HOT-MELT ADHESIVES (#526) EXCELSTAR, 0
310 511110000501R SILICONE RTV RUBBER,UB-511(EURO) EURO, 0.45

735110007800R ASSY,H/S,Q850, LE19E6-812,ROHS
XSTR FMA09N65GX N-CH TO-220F(FUJI)
10 410050103050R FUJI, 1 Q850,
RoHS
XSTR AP2761I-A N-CH TO-220CFM
10 410500059290R APEC, 0
ADVANCED P
10 410050057280R XSTR STP8NK80ZFP N-CH TO220FP (ST) ST, 0
30 507300003300R HEATSINK,"L", LE1713/1913 DMC,ORIENTAL POWER, 1
40 509146306200R SCREW,P,CROSS,W/WAS,M3*6,Zn-Cc GAOYI,LIQUAN,YIJIE, 1

735110008100R ASSY,H/S,SRF10-10CT-LF,LE22F4 ,ROHS
SCHTKY SRF10-10CT-LF 100V/10A
10 411090009020R FRONTIER, 1 D860,
TO-220AB(F
SCHTKY,SBR10100CTFP 100V/10A
10 411090009312R DIODES, 0
ITO-220AB(D
SCHTKY MBRF10100CT 100V/10A(TS
10 411090009010R TSC, 0
C)ITO-220
20 507200004200R HEATSINK,35x16.7xt10mm, LE1911 DMC,ORIENTAL POWER, 1
30 509146308102R SCREW,PW,CROSS W/WAS,M3*8,Zn GAOYI,LIQUAN,YIJIE, 1

791701440600R PCBA,PWR&INV./B,SMD,LE22F4-612 ROHS
10 419312720070R C SMD (0805) X7R 2700pF 50V K ROHS DARFON,TDK,WALSIN,YAGEO, 4 C1,C15,C16,C17,
20 419311054070R C SMD(0805) X7R 1uF/16V K RoHS REV:A DARFON,MURATA,TDK,WALSIN,YAGEO, 1 C2,
30 419311020070R C SMD(0805) X7R 1000PF/50V K RoHS DARFON,TDK,WALSIN,YAGEO, 4 C4,C5,C847,C848,

40 419312233070R C SMD(0805) X7R 0.022uF/25V K RoHS DARFON,TDK,WALSIN,YAGEO, 2 C6,C14,
50 419314730070R C SMD(0805) X7R 0.047uF/50V K ROHS DARFON,TDK,WALSIN,YAGEO, 3 C12,C13,C7,
60 419312210070R C SMD(0805) X7R 220PF/50V K RoHS DARFON,TDK,WALSIN,YAGEO, 1 C8,
70 419311040070R C SMD(0805) X7R 0.1uF/50V K RoHS REV:A DARFON,TDK,WALSIN,YAGEO, 5 C9,C10,C871,C876,C26,
80 419311030070R C SMD(0805) X7R 0.01uF/50V K RoHS DARFON,TDK,WALSIN,YAGEO, 3 C11,C849,C859,
90 414908510110R RES SMD (0805) 5.1KΩ F,RT RoHS TA-I,UNIOHM,WALSIN,YAGEO, 3 R1,R2,R858,
100 414908027350R RES SMD (0805) 27KΩ J,RT RoHS TA-I,UNIOHM,WALSIN,YAGEO, 4 R3,R4,R14,R15,
110 414908383010R RES SMD (0805) 383Ω F,RT,RoHS TA-I,UNIOHM,WALSIN,YAGEO, 2 R6,R19,
120 414908100310R RES SMD (0805) 100KΩ F,RT,RoHS TA-I,UNIOHM,WALSIN,YAGEO, 3 R5,R22,R848,
130 414908953210R RES SMD (0805) 95.3KΩ F,RT RoHS TA-I,UNIOHM,WALSIN,YAGEO, 1 R16,
140 414908510210R RES SMD (0805) 51KΩ F,RT RoHS TA-I,UNIOHM,WALSIN,YAGEO, 2 R8,R18,
150 414908010550R RES SMD (0805) 1MΩ J,RT RoHS REV:A TA-I,UNIOHM,WALSIN,YAGEO, 2 R9,R10,
R12,R13,R21,R23,R860,
160 414908100210R RES SMD (0805) 10KΩ F,RT RoHS REV:A TA-I,UNIOHM,WALSIN,YAGEO, 8
R884,R886,R887,
170 414908330310R RES SMD (0805) 330KΩ F,RT RoHS TA-I,UNIOHM,WALSIN,YAGEO, 1 R17,
180 414908100110R RES SMD (0805) 1KΩ F,RT RoHS REV:A TA-I,UNIOHM,WALSIN,YAGEO, 4 R20,R24,R30,R31,
190 414908047050R RES SMD (0805) 47Ω J,RT RoHS TA-I,UNIOHM,WALSIN,YAGEO, 2 R840,R844,
200 414904499310R RES SMD (1206) 499KΩ F,RT RoHS REV:A TA-I,UNIOHM,WALSIN,YAGEO, 6 R841,R842,R843,R850,R851,R852,
210 414904270210R RES SMD (1206) 27kΩ F,RT ROHS TA-I,UNIOHM,WALSIN,YAGEO, 3 R853,R854,R855,
38
Service Manual
220 414908100910R RES SMD(0805)10Ω F,RT ROHS TA-I,UNIOHM,WALSIN,YAGEO, 2 R856,R7,
240 414908330110R RES SMD (0805) 3.3KΩ F,RT RoHS REV:A TA-I,UNIOHM,WALSIN,YAGEO, 1 R868,
250 414908039250R RES SMD (0805) 3.9KΩ J,RT RoHS TA-I,UNIOHM,WALSIN,YAGEO, 1 R872,
270 411023004021R DIO SN4148-LF 75V/0.15A SMD 1206 (FEC)Ro FRONTIER, 1 D841,
270 411020046090R DIO 1N4148W 75V/0.15A(PEC)RoHS SOD-123 PANJIT, 0
DIO 1N4148W-F 75V/0.15A(DIODES
270 411020046310R DIODES, 0
RoHS,SOD-
280 411020068020R DIO BAW56 70V SOT-23(FRONTIER)RoHS FRONTIER, 1 ZD1,
280 411020068090R DIO BAW56 75V SOT-23(PANJIT)RoHS PANJIT, 0
280 411020068210R DIO BAW56 85V SOT-23(PHILIPS)RoHS PHILIPS, 0
290 411020047020R DIO BAV70-LF, 70V SOT-23(FEC) ROHS FRONTIER, 2 ZD2,ZD3,
290 411020047210R DIO BAV70 85V SOT23 (PHILIPS) RoHS PHILIPS, 0
290 411020047090R DIO BAV70, 70V SOT-23(PEC) ROHS PANJIT, 0
ZENER 5.6V 0.5W BZT52C5V6-F,SO
300 411131556950R DIODES, 2 ZD4,ZD5,
D123(DIOD
ZENER 5.6V BZT52-C5V6
300 411121456950R WILLAS, 0
SOD-123(WILLAS)ROH
ZENER 5.6V 0.41W BZT52-C5V6,SO
300 411120956950R PANJIT, 0
D123(PANJ
310 411020026210R DIO BAV99 350mW 70V SOT-23(PHI RoHS PHILIPS, 2 ZD6,ZD7,
310 411020026390R DIO BAV99,SOT-23(INFINEON)RoHS INFINEON, 0
310 411020026090R DIO BAV99 350mW 75V SOT-23(PEC RoHS PANJIT, 0
DIO BAV99-LF 350mW 70V SOT-23
310 411020026020R FRONTIER, 0
(FEC)RoHS
320 410080003290R XSTR AP4575GM N&P SO-8(APEC)ROHS AP, 2 Q6,Q7,
XSTR P5506NVG N&P
320 410080003430R NIKO, 0
SOP-8(NIKO-SEM)ROHS
XSTR MMBT4401 NPN
330 410070010240R FAIRCHILD, 1 Q851,
SOT23(FAIRCHILD)RoHS
330 410070010420R XSTR MMBT4401 NPN SOT23(PANJIT)RoHS PANJIT, 0
330 410070010210R XSTR PMBT4401 NPN SOT23(PHILIPS)RoHS PHILIPS, 0
340 412000628810R IC LD7552BPS SOP8（Leadtrend)ROHS LEADTREND, 1 U850,
350 412000654630R IC INL833GN SOP16(O2 MICRO)Rohs O2, 1 U1,
360 791701410600R PCBA,PWR&INV./B,AI,LE22F4-612 ROHS 1
370 419312254070R C SMD(0805) X7R 2.2uF 16V K RoHS DARFON,MURATA,TDK,WALSIN,YAGEO, 1 C3,
380 511110001100R SEAL-GLUE,NE8800K,(FUJI) FUJI, 0.03

HERAEUS
380 511110000700R D-TEK,FUHONGSHIJI,TAMURA, 0
SMT-ADHESIVE,PD955PY(TAMURA)

791701410600R PCBA,PWR&INV./B,AI,LE22F4-612 ROHS
10 791701450600R PCBA,PWR&INV./B,AI/A,LE22F4-612 RoHS 1
20 791701460600R PCBA,PWR&INV./B,AI/R,LE22F4-612 RoHS 1

791701450600R PCBA,PWR&INV./B,AI/A,LE22F4-612 RoHS
DIO FR10-10-LF 1000V/1A AT(FRO
10 411032006020R FRONTIER, 1 D851,
NTIER)RoH
10 411032006040R DIO FR107 1000V/1A DO-41(MOSPE C)RoHS MOSPEC, 0
10 411020053090R DIO PS1010R 1000V/1A DO-41(PAN JIT)RoHS PANJIT, 0
20 411020064090R DIO ER104 400V/1A DO-41(PANJIT RoHS PANJIT, 1 D852,
20 411032001020R DIO SF10-04-LF 400V/1A DO-41(F RONTIER)R FRONTIER, 0
40 415212703140R RES MF 1/8W 270KΩ F,AT,RoHS QUEENMAO,TZAI YUAN, 1 R871,
50 411131430010R ZENER 30V GDZ30A DO35(WILLAS)RoHS WILLAS, 1 ZD880,
39
Service Manual
50 411130930010R ZENER 30V GDZ30A DO35(PANJIT)RoHS PANJIT, 0
60 430613050100R FUSE SLOW PICO II 5A/125V U/C,AT,ROHS LITTELFUSE, 1 F851,
60 430613050101R FUSE SLOW 5A/125V U/C,AT,ROHS WALTER, 0
70 491571400100H PCB,P/I ,1/OSP /CEM1/16,LE22F4-612 HSIANGKUO,TAT CHUN, 1
80 430405000000R JMPR ROLL/KG D=0.6mm,AT,RoHS 7.5MM HOTRON,YUANYE, 400 J1,J2,J5,J11,J12,J13,J14,J15,
80 430405000000R JMPR ROLL/KG D=0.6mm,AT,RoHS 7.5MM HOTRON,YUANYE, 0
90 430405000000R JMPR ROLL/KG D=0.6mm,AT,RoHS 10MM HOTRON,YUANYE, 200 J3,J6,J7,J4,
90 430405000000R JMPR ROLL/KG D=0.6mm,AT,RoHS 10MM HOTRON,YUANYE, 0
100 430405000000R JMPR ROLL/KG D=0.6mm,AT,RoHS 15MM HOTRON,YUANYE, 100 J9,J10,
100 430405000000R JMPR ROLL/KG D=0.6mm,AT,RoHS 15MM HOTRON,YUANYE, 0
110 430405000000R JMPR ROLL/KG D=0.6mm,AT,RoHS 12.5MM HOTRON,YUANYE, 150 J8,J16,J17,
110 430405000000R JMPR ROLL/KG D=0.6mm,AT,RoHS 12.5MM HOTRON,YUANYE, 0
130 411020080020R DIO P6KE170A-LF 600W/100A DO-15(FEC) FRONTIER, 1 D853,
130 411020080460R DIO P6KE170A 600W/100A DO-15（SECOS） SECOS, 0
130 411020080090R DIO P6KE170A 600W/100A DO-15（PANJIT）PANJIT, 0
140 415222700140R RES MF 1/4W 270Ω F,AT,MINI,RoHS QUEENMAO,TZAI YUAN, 1 R857,
150 415215101140R RES MF 1/8W 5.1KΩ F,AT,RoHS QUEENMAO,TZAI YUAN, 2 R11,R25,
LABEL,BARCODE,BLANK,33x7mm,
160 506140005700R HENGMINGDA,JIAYINMEI,KAIDA, 1
ROHS,FOR PCB

791701460600R PCBA,PWR&INV./B,AI/R,LE22F4-612 RoHS
10 430613830290R FUSE TIME LAG 3.15A/250V,RoHS BELFUSE,CONQUER,LITTELFUSE,WALTER, 1 F850,
20 420421000530R CAP SD 10uF/50V M,VT 105℃ 5x11 RoHS LELON,SAMXON,SU'SCON,TEAPO, 1 C855,

30 420424710231R CAP SD 470uF/25V M 105℃ VT 10x16 RoHS LELON,SAMXON,SU'SCON,TEAPO, 3 C856,C857,C858,
40 418268123030R CAP CD X7R 680pF 500V K VT RoHS JNC,POE,SUCCESS(SEC), 1 C862,
50 412022002240R IC KA431AZ 1%,VT (FAIRCHILD) RoHS FAIRCHILD, 1 I851,
50 412022002830R IC AS431 TO-92 VT(A1SEMI)RoHS A1SEMI, 0
50 412022002550R IC AME431BAJATB25Z TO-92-3(AME RoHS AME, 0
50 412022002440R IC AZ431BZ-ATRE1 TO-92(BCD) RoHS BCD, 0
CAP CD X7R 1000pF/1KV K,VT
60 418210233030R JNC,POE,SUCCESS(SEC), 1 C873,
2X7R102K102K5
3.PCBA KEYPAD BOM
ITEM P/N Revision Description Supplier Usage Location
791701500000R PCBA,KEYPAD BOARD LE22F4-612 ROHS
10 430602680170R SW,METAL DOME 180gf 5P ROHS FOXCONN,HUA-JIE, 1
20 430631080190R WFR 8P 1.25MM 180° W/LOCK ROHS JOWLE,FOXCONN 1 CN101,
30 791711540000R PCBA,KEYPAD BOARD,SMT LE19E6 ROHS 1
40 511130002200R A SOLDER PASTE,Sn96.5-Ag3.0-Cu0.5 ROHS TOMAS, 0.08
40 511130002201R A SOLDER PASTE,Sn96.5%Ag3.0%Cu0.5% TOMAS, 0
40 511130002202R A SOLDER PASTE,Sn95.5%Ag3.9%Cu0.6% TAMURA, 0
ITEM P/N Revision Description Supplier Usage Location

PCBA,KEYPAD BOARD，SMT LE22F4-612
791701540000R
ROHS
10 411070093500R A LED SMD YB KPTB-1612FX151-SZ(Kingbright) KINGBRIGHT, 1 LED101,
40
Service Manual
10 411070094500R A LED SMD YB HTL-19-22UYUBC/TR8(HongTong)R HONGTONG, 0
30 491571500000H PCB,K/P ,2/ENIG/FR4 /10.LE22F4-612 EXPRESS,WELFARE, 1
4.Assembly BOM
20080403
ITEM Phant.item P/N Description Supplier Usage Un Revision
8221F4B1D010R LE22F4-B12(B)W/O SPK,US(DAO/E2209Wf)
10 453070800150R PWR CORD 10A/125V BLK 6FT UL/CSA SVT 3Cx FOXCONN,I-SHENG, 1 PC C
FOXCONN,GREATLANE,HOTRON,JVE,
20 453010100320R CABLE D-SUB 15P MALE 6FT BLACK/BLUE AB 8 廣宇, 1 PC B
30 453030300440R CABLE DVI-D 18+1P MALE 1.8M BLACK ROHS FOXCONN,HOTRON,JVE,廣宇, 1 PC A
40 x 713100005300R ASSY, PACKAGE, PACK, DAO, LE22F4 1 PC A
50 x 714070EB0000R ASSY,FINAL(B)W/O SPK,LE22F4-B12(E2209Wf) 1 PC A
20080329
713100005300R ASSY, PACKAGE, PACK, DAO, LE22F4 A
10 506250022800R LABEL,ID(LH), LE22F4 HENGMINGDA,高綺, 1 PC A
20 506250022802R LABEL,AGENCY, LE22F4 HENGMINGDA,高綺, 1 PC A
30 506431005200R FILM,SCREEN,PROTECTION,PRINTED,LE22E0 柏興,鴻旺, 1 PC A
40 506380001400R TAPE 3M-897 12x45000mm 久威,矽威, 0.00333 ROL A
50 506280007601R POSTER,QUICK SETUP,WEST, LE22F4 裕同,鴻達, 1 PC A
60 703500005700R KIT,ACCESSORY, DOC, DAO, LE22F4 裕同,鴻達, 1 PC A
70 506120300060R BAG, PLASTIC,L670*W440mm(PRINTED), LE22E 柏興,鴻旺, 1 PC A
80 506120007000R BAG PLASTIC L480xW610xT0.05mm(PRINTED) 柏興,鴻旺, 1 PC A
90 506020025000R CARTON,DELL(WWW), LE22F4 佳藝,美盈森, 1 PC A
100 506060010300R cushion-top,LE22F4 東揚, 1 PC A
110 506060010310R cushion-bottom,LE22F4 東揚, 1 PC A
120 506340004700R LABEL BLANK 101X50mm DELL EMEA CARTON 高綺,鍵升, 1 PC A
130 506380002622R TAPE, WRAPPING TYPE PRINTED(DELL), BLACK 佳普森, 0.00156 ROL A
140 x 713010000901R ASSY PACK,40STD,LE22F4 1 PC A
140 x 713010000900R ASSY PACK,20STD,LE22F4 0 PC A
140 x 713010000903R ASSY PACK,AIR CARGO(20STD),LE22F4 0 PC A
140 x 713010000904R ASSY PACK,AIRCARGO(40STD),LE22F4 0 PC A
140 x 713010000905R ASSY PACK,AIR CARGO(40H),LE22F4 0 PC A
20080403
714070EB0000R ASSY,FINAL(B)W/O SPK,LE22F4-B12(E2209Wf) A
10 509212103500R SCREW,F,CROSS,T.T-2*3,BLK 高億, 4 PC A
20 509116610510R SCREW,P,CROSS,M4*10,BLACK-NL(NYLOK) 立侑,高億, 4 PC A
30 714020014700R stand-assy,LE22F4 CJC,富鴻齊, 1 PC A
40 714030018000R front-bezel-assy,LE22F4 MMP, 1 PC A
50 714050016900R back-cover-assy,LE22F4 MMP, 1 PC A
60 x 714080EB0000R ASSY,PANEL,W/O SPK,LE22F4-B12(E2209Wf) 1 PC A
20080329
713010000900R ASSY PACK,20STD,LE22F4 A
10 506432003700R SLIP SHEET,L1192xW898xH75mm, LE22F4 SUNSTREAM, 0 PC A
20 506037009500R CARDBOARD,COVER,L1192xW898xH100xT3mm,LE2 佳藝,美盈森, 0 PC A
30 506039008800R CORNER PAPER 1060x50x50xT3mm LE1963 佳藝, 0 PC A
40 506431000300R FILM,PE 500mmx900M ROHS 三輝,柏興, 0 ROL A
50 506120400100R BAG AIR DUNNAGE 2000x1000mmLE1X03 ROHS SISUN, 0 PC A
60 506380002612R TAPE,WRAPPING TYPE,50Mx82mm 佳普森, 0 ROL A
20080329
713010000901R ASSY PACK,40STD,LE22F4 A
10 506432003700R SLIP SHEET,L1192xW898xH75mm, LE22F4 SUNSTREAM, 0.05 PC A
20 506037009500R CARDBOARD,COVER,L1192xW898xH100xT3mm,LE2 佳藝,美盈森, 0.1 PC A
30 506039008800R CORNER PAPER 1060x50x50xT3mm LE1963 佳藝, 0.2 PC A
40 506431000300R FILM,PE 500mmx900M ROHS 三輝,柏興, 0.00209 ROL A
50 506120400100R BAG AIR DUNNAGE 2000x1000mmLE1X03 ROHS SISUN, 0.00435 PC A
60 506380002612R TAPE,WRAPPING TYPE,50Mx82mm 佳普森, 0.00071 ROL A
20080329
41
Service Manual
713010000903R ASSY PACK,AIR CARGO(20STD),LE22F4 A
10 506150006900R PALLET L1284xW914xH120mm LE1746 實習工廠, 0 PC B
40 506039001400R CORNER PAPER 200x50x50mm ROHS 佳藝,金惠, 0 PC A
20080329
713010000904R ASSY PACK,AIRCARGO(40STD),LE22F4 A
20080329
713010000905R ASSY PACK,AIR CARGO(40H),LE22F4 A
30 506039000101R CORNER PAPER 1000x50x50xT3mmLE1711 佳藝,金惠, 0 PC A
20080403
714080EB0000R ASSY,PANEL,W/O SPK,LE22F4-B12(E2209Wf) A
10 631102220480RD LCP 22" LTM220M1-L01-CTB(A)(SAMSUNG)ROHS 1 PC A
10 631102220490RD LCP 22" LTM220M1-L01-CUB(A)(SAMSUNG)ROHS 0 PC A
20 701000009400R ASSY,CHASSIS,V,LE19F6 MMP, 1 PC A
30 501110200400R LOGO PLATE DELL UX383 LE1963 DEMETER, 1 PC A
40 509000001000R BOLT,#4-40x12.5,Ni ROHS 高億, 4 PC A
50 509016305200R SCREW,I,CROSS,M3*5,Zn-Cc 高億, 4 PC A
60 509016306200R SCREW,I,CROSS,M3*6,Zn-Cc 高億, 2 PC A
70 509146306200R SCREW,P,CROSS,W/WAS,M3*6,Zn-Cc 立侑,高億, 4 PC A
80 509476606200R SCREW,B,CROSS W/W(T)M3*8,ZnROHS 高億,鴻益進, 1 PC A
90 791701300B00R PCBA,I/F BOARD W/O SPK,LE22F4-B12 ROHS 1 PC
100 791701400600R PCBA,P/I BOARD W/O SPK,LE22F4-612 ROHS 1 PC
110 791701500000R PCBA,KEYPAD BOARD LE22F4-612 ROHS 1 PC
120 430303001730R HRN LVDS FFC 30P 181mm FOXCONN,P-TWO, 1 PC A
130 430300801950R HRN ASSY 2x4P to 8P 405mm UL1571#28 FOXCONN,JVE, 1 PC
Attachment 2- Schematic
1. Interface board schematic
42
Service Manual
43
Service Manual
44
Service Manual
2.power board schematic
45
Service Manual
46
Service Manual
47
Service Manual
48
Service Manual
Attachment 3- PCB Layout power/inverter bd:
power/inverter board:
Top Layer
49
Service Manual
Bottom Layer
50

E2209wf - Monitor - 44 - 51

Uploaded by

Copyright:

Available Formats

E2209wf - Monitor - 44 - 51

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

E2209wf - Monitor - 44 - 51

Uploaded by

Copyright:

Available Formats

Service Manual

Service Manual Versions and Revision

1 1.0 2008-6-3 Initial Release

All Rights Reserved

Dell E2209W Service Manual

Downloaded from www.Manualslib.com manuals search engine

Electronic Circuit Theory

2.2 Power PWM circuit

PWM controller Switching element Rectifier and filter

2.2.2) AC Input and EMI Filter:(fig.5)

2.2.3)High Voltage to Low Voltage Control Circuit:(fig.6)

Please refer to U105 (TSUMU58EHJ-LF-2) Pin Assignments table in page

4. Power On/Off Sequency

Software power On/Off

Power supply for panel+5V VDD

Signals Valid data

T1(ms) T2 (ms) T3 (ms) T4 (ms) T5 (ms) T6 (ms) T7(ms)

5. D-SUB Connector Pin Assignment

Pin Symbol Pin Symbol Pin Symbol

6. AC Outlet Pin Assignment

7. Inner Connector Pin Assignment

7.2 CN1, CN2, CN3, CN4 (Connect to Panel Backlight,)

7.3 CN104 (Connect to keypad, WAFER2*4P or compatible connector)

8.1 U108 (Serial Flash)

Note: 1. The arrows point out the direction of disassembly.

Note: 1. The arrows point out the direction of assembly

2- Menu: Call out OSD Menu and choose

4-()symbol molded into button, move up the highlight bar

Hot Key Function Automatic adjust: Directly press “”

Brightness/Contrast Icon: Directly press “”

Purpose: Automatically calibrate chip ADC parameter by using chip internal

Process: If we want to do “Auto Color Balance” again, please confirm the

Factory Mode Introduction

Back: Exit from Factory mode and back to NO OSD Status.

Dell panel P/N

Upgrade Firmware to Serial via Flash Cable by ISP_Tool V4.100.exe

※ The detailed reprogramming procedures will be described in ISP User's Guide.

Contrast Check 1. Set input mode to 1680×1050@60Hz Chroma

Is the voltage at C854 in the

Is the voltage at pin4 of U850 312V?

YES NO Check F850

Is the voltage at pin6 of U850 0.9V?

Is the voltage at pin6 of T850 120V?

Is the frequency 14.318MHz at NO

Yes Yes Change U104

Is the serial clock signal at #6 of IF NO

Power(include IF +5Vand +3.3V) supply and display normal only

Power (include IF +5Vand +3.3V) supply and display normal but

Is Power LED Amber?

Do the Hsync. & Vsync. Signals exist NO

Do the Hsync. & Vsync. Signals exist NO

Is the Q108 work normal NO

4.Power (include IF +5Vand +3.3V) supply normal ,key function

Is there 27V Voltage on No No

Is there PWM signal on No

Is there High level voltage No

Are there PWM signal on No

Backlight on ,key function and LED

Color lost in some scale at 32-gray scale pattern