New Syllabuses

AeroGATES: PART-66 syllabuses
Module 1
MATHEMATICS
1
PART-66 Syllabuses Cross-reference Level
MODULE 1. MATHEMATICS – A CATEGORY

1.1. ARITHMETIC
Arithmetical terms and signs, AG-01-01-A 1

Methods of multiplication and division,
Fractions and decimals,
Factors and multiples,
Weights, measures and conversion factors,
Ratio and proportion,
Averages and percentages,
Areas and volumes, squares, cubes,
Square and cube roots.
1.2. ALGEBRA
(a) AG-01-02a-A 1
Evaluating simple algebraic expressions, addition, subtraction, multiplication and division, use of
brackets, simple algebraic fractions.
2
(b) - -
Linear equations and their solutions,

Indices and powers, negative and fractional indices,
Binary and other applicable numbering systems,
Simultaneous equations,
Second degree equations with one unknown,
Logarithms.
1.3. GEOMETRY
(a) - -
Simple geometrical constructions.
(b) AG-01-03b-A-B1-B2-B3 2
Graphical representation; nature and uses of graphs,

Graphs of equations/functions.
(c) - -
Simple trigonometry; trigonometrical relationships, use of tables and rectangular and polar coordinates.
- -
3
MODULE 1. MATHEMATICS – B1, B2 & B3 CATEGORIES

1.1. ARITHMETIC
Arithmetical terms and signs, AG-01-01-B1-B2-B3 2

Methods of multiplication and division,
Fractions and decimals,
Factors and multiples,
Weights, measures and conversion factors,
Ratio and proportion,
Averages and percentages,
Areas and volumes, squares, cubes,
Square and cube roots.
1.2. ALGEBRA
(a) AG-01-02a-B1-B2-B3 2
Evaluating simple algebraic expressions, addition, subtraction, multiplication and division, use of
brackets, simple algebraic fractions.
4
(b) AG-01-02b-A-B1-B2-B3 1
Linear equations and their solutions,

Indices and powers, negative and fractional indices,
Binary and other applicable numbering systems,
Simultaneous equations,
Second degree equations with one unknown,
Logarithms.
1.3. GEOMETRY
(a) AG-01-3a-B1-B2-B3 1
Simple geometrical constructions.
(b) AG-01-03b-A-B1-B2-B3 2
Graphical representation; nature and uses of graphs,

Graphs of equations/functions.
(c) AG-01-3c-B1-B2-B3 1
Simple trigonometry; trigonometrical relationships, use of tables and rectangular and polar coordinates.
- -
5
Module 2
PHYSICS
6
MODULE 2. PHYSICS – A CATEGORY

2.1. MATTER
Nature of matter: the chemical elements, structure of atoms, molecules; AG-02-01-A-B1-B2-B3 1

Chemical compounds.
States: solid, liquid and gaseous;
Changes between states.
2.2. MECHANICS
2.2.1. Statics AG-02-02-01-A-B2-B3 1
Forces, moments and couples, representation as vectors;

Centre of gravity.
Elements of theory of stress, strain and elasticity: tension, compression, shear and torsion;
Nature and properties of solid, fluid and gas;
Pressure and buoyancy in liquids (barometers).
2.2.2. Kinetics AG-02-02-02-A-B2-B3 1
7
Linear movement: uniform motion in a straight line, motion under constant acceleration (motion under
gravity) ;
Rotational movement: uniform circular motion (centrifugal/centripetal forces);
Periodic motion: pendular movement;
Simple theory of vibration, harmonics and resonance;
Velocity ratio mechanical advantage and efficiency.
2.2.3. Dynamics AG-02-02-02-A-B2-B3 1
(a) Mass AG-02-02-03a-A-B2-B3 1
Mass, force, inertia, work, power, energy (potential, kinetic and total energy), heat, efficiency.
(b) Momentum, conservation of momentum AG-02-02-03b-A-B3 1
Momentum, conservation of momentum;

Impulse;
Gyroscopic principles.
Friction: nature and effects, coefficient of friction (rolling resistance).
2.2.4. Fluid dynamics
(a) AG-02-02-04a-A-B1-B2-B3 2
Specific gravity and density
(b) AG-02-02-04b-A-B2-B3 1
8
Viscosity, fluid resistance, effects of streamlining;

Effects of compressibility on fluids ;
Static, dynamic and total pressure: Bernoulli’s Theorem, Venturi
2.3. THERMODYNAMICS
(a) AG-02-03a-A-B1-B2-B3 2
Temperature: thermometers and temperature scales: Celsius, Fahrenheit and Kelvin. Heat definition.
(b) - -
Heat capacity, specific heat;

Heat transfer: convection, radiation and conduction;
Volumetric expansion;
First and second law of thermodynamics;
Isothermal, adiabatic expansion and compression, engine cycles, constant volume and constant
pressure, refrigerators and heat pumps;
Gases: ideal gases laws; specific heat at constant volume and constant pressure, work done by
expanding gas;
Latent heat of fusion and evaporation, thermal energy, heat of combustion.
2.4. OPTICS (LIGHT)
Nature of light; speed of light; - -

Laws of reflection and refraction: reflection at plane surfaces,
Reflection by spherical mirrors, refraction, lenses, fibre optics.
2.5. WAVE MOTION AND SOUND
9
Wave motion: mechanical waves, sinusoidal wave motion, - -

Interference phenomena, standing waves;
Sound: speed of sound, production of sound, intensity,
Pitch and quality, Doppler effect.
- -
10
MODULE 2. PHYSICS – B1 CATEGORY

2.1. MATTER

Chemical compounds.
2.2. MECHANICS
2.2.1. Statics AG-02-02-01-B1 2

Centre of gravity.
2.2.2. Kinetics AG-02-02-02-B1 2
11
gravity) ;
2.2.3. Dynamics
(a) Mass AG-02-02-03a-B1 2
(b) Momentum, conservation of momentum AG-02-02-03b-B1-B2 2

Impulse;
(a) AG-02-02-04a-A-B1-B2-B3 2
(b) AG-02-02-04b-B1 2
12

2.3. THERMODYNAMICS
(a) AG-02-03a-A-B1-B2-B3 2
(b) AG-02-03b-B1-B2 2

expanding gas;
2.4. OPTICS (LIGHT)
Nature of light; speed of light; AG-02-04-B1-B2 2

13
Wave motion: mechanical waves, sinusoidal wave motion, AG-02-05-B1-B2 2

- -
14

2.1. MATTER

Chemical compounds.
2.2. MECHANICS
2.2.1. Statics AG-02-02-01-A-B2-B3 1

Centre of gravity.
2.2.2. Kinetics AG-02-02-02-A-B2-B3 1
15
gravity) ;
2.2.3. Dynamics
(a) Mass AG-02-02-03a-A-B2-B3 1
(b) Momentum, conservation of momentum AG-02-02-03b-B1-B2 2

Impulse;
(a) AG-02-02-04a-A-B1-B2-B3 2
(b) AG-02-02-04b-A-B2-B3 1
16

2.3. THERMODYNAMICS
(a) AG-02-03a-A-B1-B2-B3 2
(b) AG-02-03b-B1-B2 2

expanding gas;
2.4. OPTICS (LIGHT)
Nature of light; speed of light; AG-02-04-B1-B2 2

17
Wave motion: mechanical waves, sinusoidal wave motion, AG-02-05-B1-B2 2

- -
18

2.1. MATTER

Chemical compounds.
2.2. MECHANICS
2.2.1. Statics AG-02-02-01-A-B2-B3 1

Centre of gravity.
2.2.2. Kinetics AG-02-02-02-A-B2-B3 1
19
gravity) ;
2.2.3. Dynamics
(a) Mass AG-02-02-03a-A-B2-B3 1
(b) Momentum, conservation of momentum AG-02-02-03b-A-B3 1

Impulse;
(a) AG-02-02-04a-A-B1-B2-B3 2
(b) AG-02-02-04b-A-B2-B3 1
20

2.3. THERMODYNAMICS
(a) AG-02-03a-A-B1-B2-B3 2
(b) AG-02-03a-B3 1

expanding gas;
2.4. OPTICS (LIGHT)
Nature of light; speed of light; - -

21
Wave motion: mechanical waves, sinusoidal wave motion, - -

- -
22
Module 3
ELECTRICAL FUNDAMENTALS
23
MODULE 3. ELECTRICAL FUNDAMENTALS – A CATEGORY

3.1. ELECTRON THEORY
Structure and distribution of electrical charges within: atoms, molecules, ions, compounds; AG-03-01-A-B1-B2-B3 1
Molecular structure of conductors, semiconductors and insulators.
3.2. STATIC ELECTRICITY AND CONDUCTION
Static electricity and distribution of electrostatic charges; AG-03-02-A-B3 1

Electro static laws of attraction and repulsion;
Units of charge, Coulomb's Law;
Conduction of electricity in solids, liquids, gases and vacuum.
3.3. ELECTRICAL TERMINOLOGY
The following terms, their units and factors affecting them: potential difference, electromotive force, AG-03-03-A-B3 1
voltage, current, resistance, conductance, charge, conventional current flow, electron flow.
3.4. GENERATION OF ELECTRICITY
Production of electricity by the following methods: light, heat, friction, pressure, chemical action, AG-03-04-A-B1-B2-B3 1
magnetism and motion.
24
3.5. DC SOURCES OF ELECTRICITY
Construction and basic chemical action of: primary cells, secondary cells, lead acid cells, nickel AG-03-05-A 1
cadmium cells, other alkaline cells;
Cells connected in series and parallel;
Internal resistance and its effect on a battery;
Construction, materials and operation of thermocouples;
Operation of photo-cells.
3.6. DC CIRCUITS
Ohms Law, - -
Kirchhoff’s Voltage and Current Laws;
Calculations using the above laws to find resistance voltage and current;
Significance of the internal resistance of a supply.
3.7. RESISTANCE/RESISTOR
(a) - -
Resistance and affecting factors

Specific resistance;
Resistor colour code, values and tolerances, preferred values, wattage ratings;
Resistors in series and parallel;
Calculation of total resistance using series, parallel and
Series parallel combinations;
Operation and use of potentiometers and rheostats; operation of Wheatstone Bridge.
(b) - -
25
Positive and negative temperature coefficient conductance

Fixed resistors, stability, tolerance and limitations, methods of construction;
Variable resistors, thermistors, voltage dependent resistors; construction of potentiometers and
rheostats;
Construction of Wheatstone Bridge.
3.8. POWER
Power, work and energy (kinetic and potential); - -

Dissipation of power by a resistor;
Power formula;
Calculations involving power, work and energy.
3.9. CAPACITANCE/CAPACITOR
Operation and function of a capacitor; - -

Factors affecting capacitance area of plates, distance between plates, number of plates, dielectric and
dielectric constant, working voltage, voltage rating;
Capacitor types,
Construction and function; Capacitor colour coding;
Calculations of capacitance and voltage in series and parallel circuits;
Exponential charge and discharge of a capacitor, time constants;
Testing of capacitors.
3.10. MAGNETISM
(a) - -
26
Theory of magnetism
Properties of a magnet;
Action of a magnet suspended in the Earth’s magnetic field;
Magnetisation and demagnetisation;
Magnetic shielding;
Various types of magnetic material;
Electromagnets construction and principles of operation;
Hand clasp rules to determine: magnetic field around current carrying conductor.
(b) - -
Magnetomotive force, field strength, magnetic flux density, permeability, hysteresis loop, retentivity,
coercive force reluctance, saturation point, eddy currents;
Precautions for care and storage of magnets.
3.11. INDUCTANCE/INDUCTOR
27
Faraday’s Law; - -
Action of inducing a voltage in a conductor moving in a magnetic field;
Induction principles;
Effects of the following on the magnitude of an induced voltage: magnetic field strength,
Effects of the following on the magnitude of an induced voltage: magnetic field strength, rate of change
of flux,
Number of conductor turns;
Mutual induction;
The effect the rate of change of primary current and mutual inductance has on induced voltage;
Factors affecting mutual inductance: number of turns in
coil, physical size of coil, permeability of coil, position of coils with respect to each other;
Lenz's Law and polarity determining rules;
Back emf, self induction;
Principle uses of inductors.
3.12. DC MOTOR/GENERATOR THEORY
Basic motor and generator theory; - -

Construction and purpose of components in DC generator ;
Operation of, and factors affecting output and direction of current flow in DC generators;
Operation of, and factors affecting output power, torque, speed and direction of rotation of DC motors;
Series wound, shunt wound and compound motors;
Starter generator construction.
3.13. AC THEORY
28
Sinusoidal waveform: phase, period, frequency, cycle; AG-03-13-A-B3 1

Instantaneous, average, root mean square, peak, peak to peak current values and calculations of the
values, in relation voltage, current and power;
Triangular/Square waves;
Single/3 phase principles.
3.14. RESISTIVE (R), CAPACITIVE (C) AND INDUCTIVE (L) CIRCUITS
Phase relation ship of voltage and current in L, C and R circuits, parallel, series and series parallel; - -
Impedance, phase angle, power factor and current calculations;
True power, apparent power and reactive power calculations.
3.15. TRANSFORMERS
Transformer construction principles and operation; - -

Transformer losses and methods for overcoming them;
Transformer action under load and no-load conditions;
Power transfer, efficiency, polarity markings;
Calculation of line and phase voltages and currents;
Primary and Secondary current, voltage, turns ratio, power, efficiency;
Auto transformers.
3.16. FILTERS
Operation, application and uses of the following filters: - -

Low pass, high pass, band pass, band stop.
3.17. AC GENERATORS
29
Rotation of loop in a magnetic field and waveform produced; - -

Operation and construction of revolving armature and revolving field type AC generators;
Single phase, two phase and three phase alternators;
Three phase star and delta connections advantages and uses ;
Permanent magnet generators.
3.18. AC MOTORS
Construction, principles of operation and characteristics of: AC synchronous and induction motors both - -
single and polyphase;
Methods of speed control and direction of rotation;
Methods of producing a rotating field: capacitor, inductor, shaded or split pole.
30
MODULE 3. ELECTRICAL FUNDAMENTALS – B1 & B2 CATEGORIES

Static electricity and distribution of electrostatic charges; AG-03-02-B1-B2 2

The following terms, their units and factors affecting them: potential difference, electromotive force, AG-03-03- B1-B2 2
31
Construction and basic chemical action of: primary cells, secondary cells, lead acid cells, nickel AG-03-05-B1-B2-B3 2
3.6. DC CIRCUITS
Ohms Law, AG-03-06-B1-B2 2

(a) AG-03-07a-B1-B2 2

(b) AG-03-07b-B1-B2 1
32

rheostats;
3.8. POWER
Power, work and energy (kinetic and potential); AG-03-08-B1-B2 2

Power formula;
Operation and function of a capacitor; AG-03-09-B1-B2 2

Capacitor types,
3.10. MAGNETISM
(a) AG-03-10a-B1-B2 2
33
Theory of magnetism
Magnetic shielding;
(b) AG-03-10b-B1-B2 2
34
Faraday’s Law; AG-03-11-B1-B2 2

of flux,
Mutual induction;
Basic motor and generator theory; AG-03-12-B1-B2 2

3.13. AC THEORY
35
Sinusoidal waveform: phase, period, frequency, cycle; AG-03-13-B1-B2 2

Phase relation ship of voltage and current in L, C and R circuits, parallel, series and series parallel; AG-03-14-B1-B2 2
3.15. TRANSFORMERS
Transformer construction principles and operation; AG-03-15-B1-B2 2

Auto transformers.
3.16. FILTERS
Operation, application and uses of the following filters: AG-03-16-B1-B2 1

3.17. AC GENERATORS
36
Rotation of loop in a magnetic field and waveform produced; AG-03-17-B1-B2 2

3.18. AC MOTORS
Construction, principles of operation and characteristics of: AC synchronous and induction motors both AG-03-18-B1-B2 2
37
MODULE 3. ELECTRICAL FUNDAMENTALS – B3 CATEGORY

Static electricity and distribution of electrostatic charges; AG-03-02-A-B3 1

The following terms, their units and factors affecting them: potential difference, electromotive force, AG-03-03-A-B3 1
38
Construction and basic chemical action of: primary cells, secondary cells, lead acid cells, nickel AG-03-05-B1-B2-B3 1
3.6. DC CIRCUITS
Ohms Law, AG-03-06-B3 1

(a) AG-03-07a-B3 1

(b) - -
39

rheostats;
3.8. POWER
Power, work and energy (kinetic and potential); AG-03-08-B3 1

Power formula;
Operation and function of a capacitor; AG-03-09-B3 1

Capacitor types,
3.10. MAGNETISM
(a) AG-03-10a-B3 1
40
Theory of magnetism
Magnetic shielding;
(b) AG-03-10b-B3 1
41
Faraday’s Law; AG-03-11-B3 1

of flux,
Mutual induction;
Basic motor and generator theory; AG-03-12-B3 1

3.13. AC THEORY
42
Sinusoidal waveform: phase, period, frequency, cycle; AG-03-13-A-B3 1

Phase relation ship of voltage and current in L, C and R circuits, parallel, series and series parallel; AG-03-14-B3 1
3.15. TRANSFORMERS
Transformer construction principles and operation; AG-03-15-B3 1

Auto transformers.
3.16. FILTERS
Operation, application and uses of the following filters: - -

3.17. AC GENERATORS
43
Rotation of loop in a magnetic field and waveform produced; AG-03-17-B3 1

3.18. AC MOTORS
Construction, principles of operation and characteristics of: AC synchronous and induction motors both AG-03-18-B3 1
44
Module 4
ELECTRONIC FUNDAMENTALS
45
MODULE 4. ELECTRONIC FUNDAMENTALS – B1 CATEGORY

4.1. SEMICONDUCTORS
4.1.1. Diodes
(a) AG-04-01-01a-B1-B2 2
Diode symbols;
Diode characteristics and properties;
Diodes in series and parallel;
Main characteristics and use of silicon controlled rectifiers (thyristors), light emitting diode, photo
conductive diode, varistor, rectifier diodes;
Functional testing of diodes.
(b) - -
46
Materials, electron configuration, electrical properties;

P and N type materials: effects of impurities on conduction, majority and minority characters;
PN junction in a semiconductor, development of a potential across a PN junction in unbiased, forward
biased and reverse biased conditions;
Diode parameters: peak inverse voltage, maximum forward current, temperature, frequency, leakage
current, power dissipation;
Operation and function of diodes in the following circuits: clippers, clampers, full and half wave rectifiers,
bridge rectifiers, voltage doublers and triplers;
Detailed operation and characteristics of the following devices: silicon controlled rectifier (thyristor), light
emitting diode, Schottky diode, photo conductive diode, varactor diode, varistor, rectifier diodes, and
Zener diode.
4.1.2. Transistors
(a) AG-04-01-02a-B1-B3 1
Transistor symbols; Component description and orientation;

Transistor characteristics and properties.
(b) - -
Construction and operation of PNP and NPN transistors;

Base, collector and emitter configurations;
Testing of transistors.
Basic appreciation of other transistor types and their uses.
Application of transistors: classes of amplifier (A,B,C);
Simple circuits including: bias, decoupling, feedback and stabilisation;
Multistage circuit principles: cascades, push-pull, oscillators, multivibrators, flip-flop circuits.
47
4.1.3. Integrated circuits
(a) AG-04-01-03a-B1-B3 1
Description and operation of logic circuits and linear circuits/operational amplifiers.
(b) - -
Description and operation of logic circuits and linear circuits;

Introduction to operation and function of an operational amplifier used as: integrator, differentiator,
voltage follower, comparator;
Operation and amplifier stages connecting methods: resistive capacitive, inductive (transformer),
inductive resistive (IR), direct;
Advantages and disadvantages of positive and negative feedback.
4.2. PRINTED CIRCUIT BOARDS
Description and use of printed circuit boards. AG-04-02-B1 1
4.3. SERVOMECHANISMS
(a) AG-04-03-B1 1
Understanding of the following terms: Open and closed loop systems, feedback, follow up, analogue
transducers;
Principles of operation and use of following synchro system components/features: resolvers, differential,
control and torque, transformers, inductance and capacitance transmitters.
(b) - -
48
Understanding of the following terms: Open and closed loop, follow-up, servomechanism, analogue,
transducer, null, damping, feedback, dead band;
Construction operation and use of the following synchro system components: resolvers, differential,
control and torque, E and I transformers, inductance transmitters, capacitance transmitters, synchronous
transmitters;
Servomechanism defects, reversal of synchro leads, hunting.
49

4.1. SEMICONDUCTORS
4.1.1. Diodes
(a) AG-04-01-01a-B1-B2 2
Diode symbols;
(b) AG-04-01-01b-B2 2
50

Zener diode.
4.1.2. Transistors
(a) AG-04-01-02a-B2 2

(b) AG-04-01-02b-B2 2

51
(a) - -
(b) AG-04-01-03a-B2 2

Description and use of printed circuit boards. AG-04-02-B1 2
(a) - -
transducers;
(b) AG-04-03-B2 2
52
transmitters;
53

4.1. SEMICONDUCTORS
4.1.1. Diodes
(a) AG-04-01-01a-B3 1
Diode symbols;
(b) - -
54

Zener diode.
4.1.2. Transistors
(a) AG-04-01-02a-B1-B3 1

(b) - -

55
(a) AG-04-01-03a-B1-B3 1
(b) - -

Description and use of printed circuit boards. - -
(a) - -
transducers;
(b) - -
56
transmitters;
57
Module 5
DIGITAL TECHNIQUES / ELECTRONIC

INSTRUMENT SYSTEMS
58
MODULE 5. DIGITAL TECHNIQUES – A CATEGORY

5.1. ELECTRONIC INSTRUMENT SYSTEMS
Typical systems arrangements and cockpit layout of electronic instrument systems. AG-05-01-A-B3 1
5.2. NUMBERING SYSTEMS
Numbering systems: binary, octal and hexadecimal; - -

Demonstration of conversions between the decimal and binary, octal and hexadecimal systems and vice
versa.
5.3. DATA CONVERSION
Analogue Data, Digital Data; Operation and application of analogue to digital, and digital to analogue - -
converters, inputs and outputs, limitations of various types.
5.4. DATA BUSES
Operation of data buses in aircraft systems including knowledge of ARINC and other specifications; - -
Aircraft network/Ethernet.
5.5. LOGIC CIRCUITS
(a) - -
59
Identification of common logic gate symbols, tables and equivalent circuits;

Applications used for aircraft systems, schematic diagrams.
(b) - -
Interpretation of logic diagrams.
5.6. BASIC COMPUTER STRUCTURE
(a) AG-05-06a-A 1
Computer terminology (including bit, byte, software, hard ware, CPU, IC, and various memory devices
such as RAM, ROM, PROM);
Computer technology (as applied in aircraft systems).
(b) - -
Computer related terminology;

Operation, layout and interface of the major components in a micro computer including their associated
bus systems;
Information contained in single and multi address instruction words;
Memory associated terms;
Operation of typical memory devices;
Operation, advantages and disadvantages of the various data storage systems.
5.7. MICROPROCESSORS
Functions performed and overall operation of a microprocessor; - -

Basic operation of each of the following microprocessor elements: control and processing unit, clock,
register, arithmetic logic unit.
60
5.8. INTEGRATED CIRCUITS
Operation and use of encoders and decoders; - -

Function of encoder types;
Uses of medium, large and very large scale integration.
5.9. MULTIPLEXING
Operation, application and identification in logic diagrams of multiplexers and demultiplexers. - -
5.10. FIBRE OPTICS
Advantages and disadvantages of fibre optic data transmission over electrical wire propagation; - -
Fibre optic data bus; Fibre optic related terms;
Terminations; couplers, control terminals, remote terminals;
Application of fibre optics in aircraft systems.
5.11. ELECTRONIC DISPLAYS
Principles of operation of common types of displays used in modern aircraft, including : cathode ray - -
tubes, light emitting diodes, liquid crystal display.
5.12. ELECTRONIC SENSITIVE DEVICES
Special handling of components sensitive to electrostatic discharges; AG-05-12-A-B3 1

Awareness of risks and possible damage, component and personnel anti-static protection devices.
5.13. SOFTWARE MANAGEMENT CONTROL
Awareness of restrictions, airworthiness requirements and possible catastrophic effects of unapproved - -

changes to software programmes.
61
5.14. ELECTROMAGNETIC ENVIRONMENT
Influence of the following phenomena on maintenance practices for electronic system:

 EMC-ElectroMagnetic Compatibility;
 EMI-ElectroMagnetic Interference;
 HIRF-High Intensity Radiated Field;
 Lightning/lightning protection.
5.15. TYPICAL ELECTRONIC/DIGITAL AIRCRAFT SYSTEM
General arrangement of typical electronic / digital aircraft systems and associated BITE (Built In Test - -
Equipment) testing such as:
 ACARS – ARINC Communication and Addressing and Reporting System;
 ECAM – Electronic Centralised Aircraft Monitoring;
 EFIS – Electronic Flight Instrument System;
 EICAS – Engine Indication and Crew Alerting System;
 FBW – Fly-By-Wire:
 FMS – Flight Management System;
 GPS – Global Positioning System;
 IRS – Inertial Reference System;
 TCAS – Traffic Alert Collision Avoidance System;
 IMA – Integrated Modular Avionics;
 Cabin systems;
 Information systems.
62
MODULE 5. DIGITAL TECHNIQUES – B1.1 & B1.3 CATEGORIES

Typical systems arrangements and cockpit layout of electronic instrument systems. AG-05-01-B11-B13 2
Numbering systems: binary, octal and hexadecimal; AG-05-02-B11-B13 1

versa.
Analogue Data, Digital Data; Operation and application of analogue to digital, and digital to analogue AG-05-03-B11-B13 1
5.4. DATA BUSES
Operation of data buses in aircraft systems including knowledge of ARINC and other specifications; AG-05-04-B11-B13-B2 2
5.5. LOGIC CIRCUITS
(a) AG-05-05a-B11-B13-B2 2
63

(b) - -
(a) AG-05-06a-B11-B13 2
(b) - -

bus systems;

64

5.9. MULTIPLEXING
5.10. FIBRE OPTICS
Advantages and disadvantages of fibre optic data transmission over electrical wire propagation; AG-05-10-B11-B13 1
Principles of operation of common types of displays used in modern aircraft, including : cathode ray AG-05-11-B11-B13-B2 2
Special handling of components sensitive to electrostatic discharges; AG-05-12-B11-B13-B2 2

Awareness of restrictions, airworthiness requirements and possible catastrophic effects of unapproved AG-05-13-B11-B13-B2 2
65
Influence of the following phenomena on maintenance practices for electronic system: AG-05-14-B11-B13-B2 2
General arrangement of typical electronic / digital aircraft systems and associated BITE (Built In Test AG-05-15-B11-B13-B2 2
 Cabin systems;
66
MODULE 5. DIGITAL TECHNIQUES – B1.2 & B1.4 CATEGORIES

Typical systems arrangements and cockpit layout of electronic instrument systems. AG-05-01-B12-B14 2
Numbering systems: binary, octal and hexadecimal;

Demonstration of conversions between the decimal and binary, octal and hexadecimal systems and vice - -
versa.
Analogue Data, Digital Data; Operation and application of analogue to digital, and digital to analogue
- -
5.4. DATA BUSES
Operation of data buses in aircraft systems including knowledge of ARINC and other specifications;
- -
5.5. LOGIC CIRCUITS
(a) - -
67

(b)
(a) - -
(b) - -

bus systems;
Functions performed and overall operation of a microprocessor;

Basic operation of each of the following microprocessor elements: control and processing unit, clock, - -
68
Operation and use of encoders and decoders;

Function of encoder types; - -
5.9. MULTIPLEXING
5.10. FIBRE OPTICS AG-05-10-B12-B14 1
Advantages and disadvantages of fibre optic data transmission over electrical wire propagation;
Principles of operation of common types of displays used in modern aircraft, including: cathode ray AG-05-11-B12-B14 1
Special handling of components sensitive to electrostatic discharges; AG-05-12-B12-B14 2

Awareness of restrictions, airworthiness requirements and possible catastrophic effects of unapproved AG-05-13-B12-B14 1
69
Influence of the following phenomena on maintenance practices for electronic system: AG-05-14-B12-B14 2
General arrangement of typical electronic / digital aircraft systems and associated BITE (Built In Test AG-05-15-B12-B14 2
 Cabin systems;
70
MODULE 5. DIGITAL TECHNIQUES – B2 CATEGORY

Typical systems arrangements and cockpit layout of electronic instrument systems. AG-05-01-B2 3
Numbering systems: binary, octal and hexadecimal; AG-05-02-B2 2

versa.
Analogue Data, Digital Data; Operation and application of analogue to digital, and digital to analogue AG-05-03-B2 2
5.4. DATA BUSES
Operation of data buses in aircraft systems including knowledge of ARINC and other specifications; AG-05-04-B2 2
5.5. LOGIC CIRCUITS
(a) AG-05-05a-B2 2
71

(b) AG-05-05b-B2 2
(a) - -
(b) AG-05-06b-B2 2

bus systems;
Functions performed and overall operation of a microprocessor; AG-05-07-B2 2

72
Operation and use of encoders and decoders; AG-05-08-B2 2

5.9. MULTIPLEXING
Operation, application and identification in logic diagrams of multiplexers and demultiplexers. AG-05-09-B2 2
5.10. FIBRE OPTICS
Advantages and disadvantages of fibre optic data transmission over electrical wire propagation; AG-05-10-B2 2
Principles of operation of common types of displays used in modern aircraft, including : cathode ray AG-05-11-B2 2
Special handling of components sensitive to electrostatic discharges; AG-05-12-B2 2

Awareness of restrictions, airworthiness requirements and possible catastrophic effects of unapproved AG-05-13-B2 2
73
Influence of the following phenomena on maintenance practices for electronic system: AG-05-14-B2 2
General arrangement of typical electronic / digital aircraft systems and associated BITE (Built In Test AG-05-15-B2 2
 Cabin systems;
74
MODULE 5. DIGITAL TECHNIQUES – B3 CATEGORY

Typical systems arrangements and cockpit layout of electronic instrument systems. AG-05-01-B3 1
- -
Numbering systems: binary, octal and hexadecimal;
versa.
Analogue Data, Digital Data; Operation and application of analogue to digital, and digital to analogue - -
5.4. DATA BUSES
Operation of data buses in aircraft systems including knowledge of ARINC and other specifications; - -
5.5. LOGIC CIRCUITS
75
(a) AG-05-05a-B3 1

(b) - -
(a) - -
(b) - -

bus systems;
76


5.9. MULTIPLEXING
5.10. FIBRE OPTICS
Advantages and disadvantages of fibre optic data transmission over electrical wire propagation; - -
Principles of operation of common types of displays used in modern aircraft, including : cathode ray AG-05-11-B3 1
Special handling of components sensitive to electrostatic discharges; AG-05-12-B3 1

77
Awareness of restrictions, airworthiness requirements and possible catastrophic effects of unapproved AG-05-13-B3 1
Influence of the following phenomena on maintenance practices for electronic system: AG-05-14-B3 1
78
General arrangement of typical electronic / digital aircraft systems and associated BITE (Built In Test AG-05-15-B3 1
 Cabin systems;
79
Module 6
MATERIALS AND HARDWARE
80
MODULE 6. MATERIALS AND HARDWARE – A CATEGORY

6.1. AIRCRAFT MATERIALS - FERROUS
(a) AG-06-01a-A-B2 1
Characteristics, properties and identification of common alloy steels used in aircraft;

Heat treatment and application of alloy steels.
(b) - -
Testing of ferrous materials for hardness, tensile strength, fatigue strength and impact resistance.
6.2. AIRCRAFT MATERIALS – NON-FERROUS
(a) AG-06-02a-A-B2 1
Characteristics, properties and identification of common non-ferrous materials used in aircraft;

Heat treatment and application of non-ferrous materials.
(b) - -
Testing of non-ferrous material for hardness, tensile strength, fatigue strength and impact resistance.
6.3. AIRCRAFT MATERIALS – COMPOSITE AND NON-METALLIC

81
6.3.1. Composite and non-metallic other than wood and fabric
(a) AG-06-03-01a-A 1
Characteristics, properties and identification of common composite and non-metallic materials, other
than wood, used in aircraft;
Sealant and bonding agents.
(b) AG-06-03-01b-A 1
The detection of defects/deterioration in composite and non-metallic material.

Repair of composite and non-metallic material.
6.3.2. Wooden structures
Construction methods of wooden airframe structures; AG-06-03-02-A 1

Characteristics, properties and types of wood and glue used in aeroplanes;
Preservation and maintenance of wooden structure;
Types of defects in wood material and wooden structures;
The detection of defects in wooden structure;
Repair of wooden structure.
6.3.3. Fabric covering
Characteristics, properties and types of fabrics used in aeroplanes; AG-06-03-03-A 1

Inspections methods for fabric;
Types of defects in fabric; repair of fabric covering.
6.4. CORROSION
82
(a) AG-06-04a-A-B1-B2-B3 1
Chemical fundamentals;
Formation by, galvanic action process, microbiological, stress.
(b) AG-06-04b-A-B2-B3 2
Types of corrosion and their identification;

Causes of corrosion;
Material types, susceptibility to corrosion.
6.5. FASTENERS
6.5.1. Screw threads AG-06-05-01-A-B1-B2-B3 2
Screw nomenclature;
Thread forms, dimension and tolerances for standard thread used in aircraft;
Measuring screw threads
6.5.2. Bolts, studs and screws AG-06-05-02-A-B1-B2-B3 2
Bolt types: specification, identification and marking of aircraft bolts, international standards;
Nuts: self locking, anchor, standard types;
Machine screws: aircraft specifications;
Studs: types and uses, insertion and removal;
Self tapping screws, dowels.
6.5.3. Locking devices AG-06-05-03-A-B1-B2-B3 2
83
Tab and spring washers, locking plates, split pins, pal-nuts, wire locking, quick release fasteners, keys,
circlips, cotter pins.
6.5.4. Aircraft rivets AG-06-05-04-A-B2 1
Types of solid and blind rivets: specifications and identification;

Heat treatment.
6.6. PIPES AND UNIONS
(a) AG-06-06a-A-B1-B2-B3 2
Identification of, and types of rigid and flexible pipes and their connectors used in aircraft.
(b) AG-06-06b-A-B1-B3 2
Standard unions for aircraft hydraulic, fuel, oil, pneumatic and air system pipes.
6.7. SPRINGS
Types of springs, materials, characteristics and applications. - -
6.8. BEARINGS
Purpose of bearings, loads, material, construction; Types of bearings and their application. AG-06-08-A-B3 1
6.9. TRANSMISSIONS
Gear types and their application; AG-06-09-A-B3 1

Gear ratios, reduction and multiplication gear systems, driven and driving gears, idler gears, mesh
patterns;
Belts and pulleys, chains and sprockets.
84
6.10. CONTROL CABLES
Types of cables; AG-06-10-A-B2 1

End fittings, turnbuckles and compensation devices;
Pulleys and cable system components;
Bowden cables;
Aircraft flexible control systems.
6.11. ELECTRICAL CABLES AND CONNECTORS
Cable types, construction and characteristics; AG-06-11-A 1

High tension and co-axial cables;
Crimping;
Connector types, pins, plugs, sockets, insulators, current and voltage rating, coupling, identification
codes.
85
MODULE 6. MATERIALS AND HARDWARE – B1 CATEGORY

(a) AG-06-01a-B1-B3 2

(b) AG-06-01b-B1-B2-B3 1
(a) AG-06-02a-B1-B3 2

(b) AG-06-02a-B1-B2-B3 1
86
(a) AG-06-03-01a-B1-B2-B3 2
(b) AG-06-03-01b-B1-B3 2

Construction methods of wooden airframe structures; AG-06-03-02-B1-B3 2

Characteristics, properties and types of fabrics used in aeroplanes; AG-06-03-03-B1-B3 2

87
6.4. CORROSION
(a) AG-06-04a-A-B1-B2-B3 1
(b) AG-06-04b-B1 3

6.5. FASTENERS
Screw nomenclature;
88
6.5.4. Aircraft rivets AG-06-05-04-B1-B3 2

Heat treatment.
(a) AG-06-06a-A-B1-B2-B3 2
(b) AG-06-06b-A-B1-B3 2
6.7. SPRINGS
Types of springs, materials, characteristics and applications. AG-06-07-B1 2
6.8. BEARINGS
Purpose of bearings, loads, material, construction; Types of bearings and their application. AG-06-08-B1-B2 2
6.9. TRANSMISSIONS
Gear types and their application; AG-06-09-B1-B2 2

patterns;
89
Types of cables; AG-06-10-B1-B3 2

Bowden cables;
Cable types, construction and characteristics; AG-06-11-B1-B2-B3 2

Crimping;
codes.
90

(a) AG-06-01a-A-B2 1

(b) AG-06-01b-B1-B2-B3 1
(a) AG-06-02a-A-B2 1

(b) AG-06-02a-B1-B2-B3 1
91
(a) AG-06-03-01a-B1-B2-B3 2
(b) - -

Construction methods of wooden airframe structures; - -

Characteristics, properties and types of fabrics used in aeroplanes; - -

92
6.4. CORROSION
(a) AG-06-04a-A-B1-B2-B3 1
(b) AG-06-04b-A-B2-B3 2

6.5. FASTENERS
Screw nomenclature;
93
6.5.4. Aircraft rivets AG-06-05-04-A-B2 1

Heat treatment.
(a) AG-06-06a-A-B1-B2-B3 2
(b) AG-06-06b-B2 1
6.7. SPRINGS
Types of springs, materials, characteristics and applications. AG-06-07-B2-B3 1
6.8. BEARINGS
Purpose of bearings, loads, material, construction; Types of bearings and their application. AG-06-08-B1-B2 2
6.9. TRANSMISSIONS
Gear types and their application; AG-06-09-B1-B2 2

patterns;
94
Types of cables; AG-06-10-A-B2 1

Bowden cables;

Crimping;
codes.
95

(a) AG-06-01a-B1-B3 2

(b) AG-06-01b-B1-B2-B3 1
(a) AG-06-02a-B1-B3 2

(b) AG-06-02a-B1-B2-B3 1
96
(a) AG-06-03-01a-B1-B2-B3 2
(b) AG-06-03-01b-B1-B3 2

Construction methods of wooden airframe structures; AG-06-03-02-B1-B3 2

Characteristics, properties and types of fabrics used in aeroplanes; AG-06-03-03-B1-B3 2

97
6.4. CORROSION
(a) AG-06-04a-A-B1-B2-B3 1
(b) AG-06-04b-A-B2-B3 2

6.5. FASTENERS
Screw nomenclature;
98
6.5.4. Aircraft rivets AG-06-05-04-B1-B3 2

Heat treatment.
(a) AG-06-06a-A-B1-B2-B3 2
(b) AG-06-06b-A-B1-B3 2
6.7. SPRINGS
Types of springs, materials, characteristics and applications. AG-06-07-B2-B3 1
6.8. BEARINGS
Purpose of bearings, loads, material, construction; Types of bearings and their application. AG-06-08-A-B3 1
6.9. TRANSMISSIONS
Gear types and their application; AG-06-09-A-B3 1

patterns;
99
Types of cables; AG-06-10-B1-B3 2

Bowden cables;

Crimping;
codes.
100
Module 7
MAINTENANCE PRACTICES
101
MODULE 7A. MAINTENANCE PRACTICES – A CATEGORY

7.1. SAFETY PRECAUTIONS-AIRCRAFT AND WORKSHOP
Aspects of safe working practices including precautions to take when working with electricity, gases AG-07A-01-A-B1-B2 3
especially oxygen, oils and chemicals.
Also, instruction in the remedial action to be taken in the event of a fire or another accident with one or
more of these hazards including knowledge on extinguishing agents.
7.2. WORKSHOP PRACTICES
Care of tools, control of tools, use of workshop materials; AG-07A-02-A-B1-B2 3

Dimensions, allowances and tolerances, standards of workmanship.
Calibration of tools and equipment, calibration standards.
7.3. TOOLS
Common hand tool types; AG-07A-03-A-B1-B2 3

Common power tool types;
Operation and use of precision measuring tools;
Lubrication equipment and methods.
Operation, function and use of electrical general test equipment.
102
7.4. AVIONIC TEST EQUIPMENT
Operation, function and use of avionic general test equipment. - -
7.5. ENGINEERING DRAWINGS, DIAGRAMS AND STANDARDS
Drawing types and diagrams, their symbols, dimensions, tolerances and projections; AG-07A-05-A 1
Identifying title block information;
Microfilm, microfiche and computerised presentations;
Specification 100 of the Air Transport Association (ATA) of America;
Aeronautical and other applicable standards including ISO, AN, MS, NAS and MIL;
Wiring diagrams and schematic diagrams.
7.6. FITS AND CLEARANCES
Drill sizes for bolt holes, classes of fits; AG-07A-06-A-B2 1

Common system of fits and clearances;
Schedule of fits and clearances for aircraft and engines;
Limits for bow, twist and wear;
Standard methods for checking shafts, bearings and other parts.
7.7. ELECTRICAL WIRING INTERCONNECTION SYSTEM (EWIS)
103
Continuity, insulation and bonding techniques and testing; AG-07A-07-A 1

Use of crimp tools: hand and hydraulic operated;
Testing of crimp joints;
Connector pin removal and insertion;
Co-axial cables: testing and installation precautions;
Identification of wire types, their inspection criteria and damage tolerance;
Wiring protection techniques: Cable looming and loom support, cable clamps protective sleeving
techniques including heat shrink wrapping, shielding;
EWIS installations, inspection, repair, maintenance and cleanliness standards.
7.8. RIVETING
Riveted joints, rivet spacing and pitch; AG-07A-08-A 1

Tools used for riveting and dimpling;
Inspection of riveted joints.
7.9. PIPES AND HOSES
Bending and belling / flaring aircraft pipes; AG-07A-09-A 1

Inspection and testing of aircraft pipes and hoses;
Installation and clamping of pipes.
7.10. SPRINGS
Inspection and testing of springs. AG-07A-10-A 1
7.11. BEARINGS
104
Testing, cleaning and inspection of bearings; AG-07A-11-A 1

Lubrication requirements of bearings;
Defects in bearings and their causes.
7.12. TRANSMISSIONS
Inspection of gears, backlash; AG-07A-12-A 1

Inspection of belts and pulleys, chains and sprockets;
Inspection of screw jacks, lever devices, push-pull rod systems.
Swaging of end fittings; AG-07A-13-A 1

Inspection and testing of control cables;
Bowden cables; aircraft flexible control systems.
7.14. MATERIAL HANDLING
7.14.1. Sheet metal - -
Marking out and calculation of bend allowance;

Sheet metal working, including bending and forming;
Inspection of sheet metal work.
7.14.2. Composite and non-metallic - -
Bonding practices;
Environmental conditions
Inspection methods
105
7.15. WELDING, BRAZING, SOLDERING AND BONDING
(a) - -
Soldering methods; inspection of soldered joints.
(b) - -
Welding and brazing methods;

Inspection of welded and brazed joints;
Bonding methods and inspection of bonded joints.
7.16. AIRCRAFT WEIGHT AND BALANCE
(a) - -
Centre of gravity/Balance limits calculation: use of relevant documents.
(b) - -
Preparation of aircraft for weighing;

Aircraft weighing.
7.17. AIRCRAFT HANDLING AND STORAGE
106
Aircraft taxiing / towing and associated safety precautions; AG-07A-17-A-B1-B2 2

Aircraft jacking, chocking, securing and associated safety precautions;
Aircraft storage methods;
Refuelling / de-fuelling procedures;
De-icing / anti-icing procedures;
Electrical, hydraulic and pneumatic ground supplies;
Effects of environmental conditions on aircraft handling and operation.
7.18. DISASSEMBLY, INSPECTION, REPAIR, AND ASSEMBLY TECHNIQUES
(a)
Types of defects and visual inspection techniques. AG-07A-18a-A 2

Corrosion removal, assessment and re-protection.
(b) - -
General repair methods, Structural Repair Manual;

Ageing, fatigue and corrosion control programmes.
(c) - -
Non destructive inspection techniques including, penetrant, radiographic, eddy current, ultrasonic and
boroscope methods.
(d)
Disassembly and re-assembly techniques. AG-07A-18d-A-B1-B2 2
(e)
107
Trouble shooting techniques. - -
7.19. ABNORMAL EVENTS
(a) AG-07A-19a-A-B1-B2 2
Inspections following lightning strikes and HIRF penetration.
(b) AG-07A-19b-A-B1 2
Inspections following abnormal events such as heavy landings and flight through turbulence.
7.20. MAINTENANCE PROCEDURES
Maintenance planning; AG-07A-20-A 1

Modification procedures;
Stores procedures;
Certification / release procedures;
Interface with aircraft operation;
Maintenance Inspection / Quality Control / Quality Assurance ;
Additional maintenance procedures.
Control of life limited components.
108
MODULE 7A. MAINTENANCE PRACTICES – B1 CATEGORY


7.3. TOOLS

109
Operation, function and use of avionic general test equipment. AG-07A-04-B1 2
Drawing types and diagrams, their symbols, dimensions, tolerances and projections; AG-07A-05-B1-B2 2
Drill sizes for bolt holes, classes of fits; AG-07A-06-B1 2

110
Continuity, insulation and bonding techniques and testing; AG-07A-07-B1-B2 3

7.8. RIVETING
Riveted joints, rivet spacing and pitch; AG-07A-08-B1 2

Bending and belling / flaring aircraft pipes; AG-07A-09-B1 2

7.10. SPRINGS
Inspection and testing of springs. AG-07A-10-B1 2
7.11. BEARINGS
111
Testing, cleaning and inspection of bearings; AG-07A-11-B1 2

7.12. TRANSMISSIONS
Inspection of gears, backlash; AG-07A-12-B1 2

Swaging of end fittings; AG-07A-13-B1 2

7.14.1. Sheet metal AG-07A-14a-B1 2

7.14.2. Composite and non-metallic AG-07A-14b-B1 2
Bonding practices;
Inspection methods
112
(a) AG-07A-15a-B1-B2 2
(b) AG-07A-15b-B1 2

(a) AG-07A-16a-B1-B2 2
(b) AG-07A-16b-B1 2

Aircraft weighing.
113

(a)
Types of defects and visual inspection techniques. AG-07A-18a-B1-B2 3

(b) AG-07A-18b-B1 2

(c) AG-07A-18c-B1 2
boroscope methods.
(d) AG-07A-18d-A-B1-B2 2
Disassembly and re-assembly techniques.
(e) AG-07A-18e-B1-B2 2
114
Trouble shooting techniques.
(a) AG-07A-19a-A-B1-B2 2
(b) AG-07A-19b-A-B1 2
Maintenance planning; AG-07A-20-B1-B2 2

Stores procedures;
115
MODULE 7A. MAINTENANCE PRACTICES – B2 CATEGORY


7.3. TOOLS

116
Operation, function and use of avionic general test equipment. AG-07A-04-B2 3
Drawing types and diagrams, their symbols, dimensions, tolerances and projections; AG-07A-05-B1-B2 2
Drill sizes for bolt holes, classes of fits; AG-07A-06-A-B2 2

117
Continuity, insulation and bonding techniques and testing; AG-07A-07-B1-B2 3

7.8. RIVETING
Riveted joints, rivet spacing and pitch; - -

Bending and belling / flaring aircraft pipes; - -

7.10. SPRINGS
Inspection and testing of springs. - -
7.11. BEARINGS
118
Testing, cleaning and inspection of bearings; - -

7.12. TRANSMISSIONS
Inspection of gears, backlash; - -

Swaging of end fittings; - -

7.14.1. Sheet metal - -

7.14.2. Composite and non-metallic - -
Bonding practices;
Inspection methods
119
(a) AG-07A-15a-B1-B2 2
(b) - -

(a) AG-07A-16a-B1-B2 2
(b) - -

Aircraft weighing.
120

(a)
Types of defects and visual inspection techniques. AG-07A-18a-B1-B2 3

(b) - -

(c) AG-07A-18c-B2 1
boroscope methods.
(d) AG-07A-18d-A-B1-B2 2
Disassembly and re-assembly techniques.
(e) AG-07A-18e-B1-B2 2
121
Trouble shooting techniques.
(a) AG-07A-19a-A-B1-B2 2
(b) - -
Maintenance planning; AG-07A-20-B1-B2 2

Stores procedures;
122
MODULE 7B. MAINTENANCE PRACTICES – B3 CATEGORY

Aspects of safe working practices including precautions to take when working with electricity, gases AG-07B-01-B3 3
Care of tools, control of tools, use of workshop materials; AG-07B-02-B3 3

7.3. TOOLS
Common hand tool types; AG-07B-03-B3 3

123
Operation, function and use of avionic general test equipment. - -
Drawing types and diagrams, their symbols, dimensions, tolerances and projections; AG-07B-05-B3 2
Drill sizes for bolt holes, classes of fits; AG-07B-06-B3 2

124
Continuity, insulation and bonding techniques and testing; AG-07B-07-B3 2

7.8. RIVETING
Riveted joints, rivet spacing and pitch; AG-07B-08-B3 2

Bending and belling / flaring aircraft pipes; AG-07B-09-B3 2

7.10. SPRINGS
Inspection and testing of springs. AG-07B-10-B3 1
7.11. BEARINGS
125
Testing, cleaning and inspection of bearings; AG-07B-11-B3 2

7.12. TRANSMISSIONS
Inspection of gears, backlash; AG-07B-12-B3 2

Swaging of end fittings; AG-07B-13-B3 2

7.14.1. Sheet metal AG-07B-14a-B3 2

7.14.2. Composite and non-metallic AG-07B-14b-B3 2
Bonding practices;
Inspection methods
126
(a) AG-07B-15a-B3 2
(b) AG-07B-15b-B3 2

(a) AG-07B-16a-B3 2
(b) AG-07B-16b-B3 2

Aircraft weighing.
127
Aircraft taxiing / towing and associated safety precautions; AG-07B-17-B3 2

(a)
Types of defects and visual inspection techniques. AG-07B-18a-B3 3

(b) AG-07B-18b-B3 2

(c) AG-07B-18c-B3 2
boroscope methods.
(d)
Disassembly and re-assembly techniques. AG-07B-18d-B3 2
(e)
128
Trouble shooting techniques. AG-07B-18e-B3 2
(a) AG-07B-19a-B3 2
(b) AG-07B-19b-B3 2
Maintenance planning; AG-07B-20-B3 2

Stores procedures;
129
Module 8
BASIC AERODYNAMICS
130
MODULE 8. BASIC AERODYNAMICS – A & B3 CATEGORIES

8.1. PHYSICS OF THE ATMOSPHERE
International Standard Atmosphere (ISA), application to aerodynamics. AG-08-01-B1-B2 2
8.2. AERODYNAMICS
Airflow around a body; AG-08-02-B1-B2 2

Boundary layer, laminar and turbulent flow, free stream flow, relative airflow, upwash and downwash,
vortices, stagnation;
The terms: camber, chord, mean aerodynamic chord, profile (parasite) drag, induced drag, centre of
pressure, angle of attack, wash in and wash out, fineness ratio, wing shape and aspect ratio;
Thrust, Weight, Aerodynamic Resultant;
Generation of Lift and Drag: Angle of Attack, Lift coefficient, Drag coefficient, polar curve, stall;
Aerofoil contamination including ice, snow, frost.
8.3. THEORY OF FLIGHT
131
Relation ship between lift, weight, thrust and drag; Glide ratio; AG-08-03-B1-B2 2
Steady stable flights, performance;
Theory of the turn;
Influence of load factor: stall, flight envelope and structural limitations;
Lift augmentation.
8.4. FLIGHT STABILITY AND DYNAMICS
Longitudinal, lateral and directional stability (active and passive). AG-08-04-B1-B2 2
132
MODULE 8. BASIC AERODYNAMICS – B1 & B2 CATEGORIES

8.1. PHYSICS OF THE ATMOSPHERE
International Standard Atmosphere (ISA), application to aerodynamics. AG-08-01-A-B3 1
8.2. AERODYNAMICS
Airflow around a body; AG-08-02-A-B3 1

Boundary layer, laminar and turbulent flow, free stream flow, relative airflow, upwash and downwash,
vortices, stagnation;
The terms: camber, chord, mean aerodynamic chord, profile (parasite) drag, induced drag, centre of
pressure, angle of attack, wash in and wash out, fineness ratio, wing shape and aspect ratio;
Thrust, Weight, Aerodynamic Resultant;
Generation of Lift and Drag: Angle of Attack, Lift coefficient, Drag coefficient, polar curve, stall;
Aerofoil contamination including ice, snow, frost.
133
Relation ship between lift, weight, thrust and drag; Glide ratio; AG-08-03-A-B3 1
Steady stable flights, performance;
Theory of the turn;
Influence of load factor: stall, flight envelope and structural limitations;
Lift augmentation.
8.4. FLIGHT STABILITY AND DYNAMICS
Longitudinal, lateral and directional stability (active and passive). AG-08-04-A-B3 1
134
Module 9
HUMAN FACTORS
135
MODULE 9A. HUMAN FACTORS – A CATEGORY

9.1. GENERAL
The need to take human factors into account; AG-09A-01-A 1

Incidents attributable to human factors / human error;
‘Murphy's’ law.
9.2. HUMAN PERFORMANCE AND LIMITATIONS
Vision; AG-09A-02-A 1
Hearing;
Information processing;
Attention and perception;
Memory;
Claustrophobia and physical access.
9.3. SOCIAL PSYCHOLOGY
136
Responsibility: individual and group; AG-09A-03-A-B1-B2 1

Motivation and de-motivation;
Peer pressure;
‘Culture’ issues;
Team working;
Management, Supervision and leadership.
9.4. FACTORS AFFECTING PERFORMANCE
Fitness / health; AG-09A-04-A-B1-B2 2

Stress: domestic and work related;
Time pressure and deadlines;
Workload: over load and underload;
Sleep and fatigue, shiftwork;
Alcohol, medication, drug abuse.
9.5. PHYSICAL ENVIRONMENT
Noise and fumes; AG-09A-05-A-B1-B2 1

Illumination;
Climate and temperature;
Motion and vibration;
Working environment.
9.6. TASKS
137
Physical work; AG-09A-06-A-B1-B2 1

Repetitive tasks;
Visual inspection;
Complex systems.
9.7. COMMUNICATION
Within and between teams; AG-09A-07-A-B1-B2 2

Work logging and recording;
Keeping up to date, currency;
Dissemination of information.
9.8. HUMAN ERROR
Error models and theories; AG-09A-08-A 1

Types of error in maintenance tasks;
Implications of errors (i.e accidents);
Avoiding and managing errors.
9.9. HAZARDS IN THE WORKPLACE
Recognising and avoiding hazards; AG-09A-09-A 1

Dealing with emergencies.
138
MODULE 9A. HUMAN FACTORS – B1 & B2 CATEGORIES

9.1. GENERAL
The need to take human factors into account; AG-09A-01-B1-B2 2

‘Murphy's’ law.
Vision; AG-09A-02-B1-B2 2
Hearing;
Memory;
139
Responsibility: individual and group; AG-09A-03-A-B1-B2 1

Peer pressure;
Team working;
Fitness / health; AG-09A-04-A-B1-B2 2

Noise and fumes; AG-09A-05-A-B1-B2 1

Illumination;
9.6. TASKS
140
Physical work; AG-09A-06-A-B1-B2 1

Repetitive tasks;
Visual inspection;
Complex systems.
9.7. COMMUNICATION
Within and between teams; AG-09A-07-A-B1-B2 2

9.8. HUMAN ERROR
Error models and theories; AG-09A-08-B1-B2 2

Recognising and avoiding hazards; AG-09A-09-B1-B2 2

141
MODULE 9B. HUMAN FACTORS – B3 CATEGORY

9.1. GENERAL
The need to take human factors into account; AG-09B-01-B3 2

‘Murphy's’ law.
Vision; AG-09B-02-B3 2
Hearing;
Memory;
142
Responsibility: individual and group; AG-09B-03-B3 1

Peer pressure;
Team working;
Fitness / health; AG-09B-04-B3 2

Noise and fumes; AG-09B-05-B3 1

Illumination;
9.6. TASKS
143
Physical work; AG-09B-06-B3 1

Repetitive tasks;
Visual inspection;
Complex systems.
9.7. COMMUNICATION
Within and between teams; AG-09B-07-B3 2

9.8. HUMAN ERROR
Error models and theories; AG-09B-08-B3 2

Recognising and avoiding hazards; AG-09B-09-B3 2

144
MODULE 9B. HUMAN FACTORS – B3 CATEGORY

9.1. GENERAL
The need to take human factors into account; AG-09B-01-B3 2

‘Murphy's’ law.
Vision; AG-09B-02-B3 2
Hearing;
Memory;
145
Responsibility: individual and group; AG-09B-03-B3 1

Peer pressure;
Team working;
Fitness / health; AG-09B-04-B3 2

Noise and fumes; AG-09B-05-B3 1

Illumination;
9.6. TASKS
146
Physical work; AG-09B-06-B3 1

Repetitive tasks;
Visual inspection;
Complex systems.
9.7. COMMUNICATION
Within and between teams; AG-09B-07-B3 2

9.8. HUMAN ERROR
Error models and theories; AG-09B-08-B3 2

Recognising and avoiding hazards; AG-09B-09-B3 2

147
Module 10
AVIATION LEGISLATION
148
MODULE 10. AVIATION LEGISLATION – A CATEGORY

10.1. REGULATORY FRAMEWORK
Role of International Civil Aviation Organisation; AD-10-01-A-B1-B2-B3 1

Role of the European Commission;
Role of EASA;
Role of the Member States and the National Aviation Authorities
Regulation (EC) N° 216/2008 and its implementing rules Regulations (EC) N° 1702/2003 and (EC) N°
2042/2003.
Relationships between the various Annexes (Parts) such as Part-21, Part-M, Part-145, Part-66, Part-147
and EO-OPS.
10.2. CERTIFYING STAFF - MAINTENANCE
Detailed understanding of Part-66. AD-10-02-A-B1-B2-B3 2
10.3. APPROVED MAINTENANCE ORGANIZATIONS
Detailed understanding of Part-145 and Part-M Subpart F. AD-10-03-A-B1-B2-B3 2
10.4. AIR OPERATIONS
149
General understanding of EU-OPS; AD-10-04-A-B1-B2-B3 1

Air Operators Certificates;
Operators Responsibilities, in particular regarding continuing airworthiness and maintenance;
Aircraft Maintenance Programme;
MEL/CDL;
Documents to be carried on board;
Aircraft placarding (markings).
10.5. CERTIFICATION OF AIRCRAFT, PARTS AND APPLIANCES
(a) General - -
General understanding of Part-21 and EASA certification specifications CS-23, 25, 27, 29.
(b) Documents - -
Certificate of Airworthiness; restricted certificates of airworthiness and permit to fly;

Certificate of registration;
Noise certificate;
Weight schedule;
Radio station licence and approval.
10.6. CONTINUING AIRWORTHINESS
Detailed understanding of Part-21 provisions related to continuing airworthiness; AD-10-06-A-B1-B2-B3 2

Detailed understanding of Part-M.
10.7. APPLICABLE NATIONAL AND INTERNATIONAL REQUIREMENTS FOR (IF NOT

SUPERSEDED BY EU REQUIREMENTS).
150
(a)
Maintenance programmes, maintenance checks and inspections; AD-10-07a-A 1

Airworthiness directives;
Service bulletins, manufacturers service information;
Modifications and repairs;
Maintenance documentation: maintenance manuals, structural repair manual, illustrated parts
catalogue, etc.
Master Minimum Equipment Lists, Minimum equipment lists, Dispatch Deviation lists.
(b) - -
Continuing airworthiness;
Minimum equipment requirements – Test flights.
151
MODULE 10. AVIATION LEGISLATION – B1, B2 & B3 CATEGORIES

10.1. REGULATORY FRAMEWORK
Role of International Civil Aviation Organisation; AG-10-01-A-B1-B2-B3 1

Role of the European Commission;
Role of EASA;
Role of the Member States and the National Aviation Authorities
Regulation (EC) N° 216/2008 and its implementing rules Regulations (EC) N° 1702/2003 and (EC) N°
2042/2003.
Relationships between the various Annexes (Parts) such as Part-21, Part-M, Part-145, Part-66, Part-147
and EO-OPS.
10.2. CERTIFYING STAFF - MAINTENANCE
Detailed understanding of Part-66. AG-10-02-A-B1-B2-B3 2
10.3. APPROVED MAINTENANCE ORGANIZATIONS
Detailed understanding of Part-145 and Part-M Subpart F. AG-10-03-A-B1-B2-B3 2
10.4. AIR OPERATIONS
152
General understanding of EU-OPS; AG-10-04-A-B1-B2-B3 1

Air Operators Certificates;
Operators Responsibilities, in particular regarding continuing airworthiness and maintenance;
Aircraft Maintenance Programme;
MEL/CDL;
Documents to be carried on board;
Aircraft placarding (markings).
10.5. CERTIFICATION OF AIRCRAFT, PARTS AND APPLIANCES
(a) General AG-10-05a-B1-B2-B3 1
General understanding of Part-21 and EASA certification specifications CS-23, 25, 27, 29.
(b) Documents AG-10-05b-B1-B2-B3 2
Certificate of Airworthiness; restricted certificates of airworthiness and permit to fly;

Certificate of registration;
Noise certificate;
Weight schedule;
Radio station licence and approval.
10.6. CONTINUING AIRWORTHINESS
Detailed understanding of Part-21 provisions related to continuing airworthiness; AG-10-06-A-B1-B2-B3 2

Detailed understanding of Part-M.
10.7. APPLICABLE NATIONAL AND INTERNATIONAL REQUIREMENTS FOR (IF NOT

SUPERSEDED BY EU REQUIREMENTS).
153
(a) AG-10-07a-B1-B2-B3 2
Maintenance programmes, maintenance checks and inspections;

Airworthiness directives;
Service bulletins, manufacturers service information;
Modifications and repairs;
Maintenance documentation: maintenance manuals, structural repair manual, illustrated parts
catalogue, etc.
Master Minimum Equipment Lists, Minimum equipment lists, Dispatch Deviation lists.
(b) AG-10-07b-B1-B2-B3 1
Continuing airworthiness;
Minimum equipment requirements – Test flights.
154
Module 11
TURBINE AEROPLANE
AERODYNAMICS, STRUCTURES AND
SYSTEMS
155
156
MODULE 11A. TURBINE AEROPLANE AERODYNAMICS, STRUCTURES AND

SYSTEMS – A1 CATEGORY
11A.1. THEORY OF FLIGHT
11A.1.1. Aeroplane Aerodynamics and Flight controls AG-11A-01-01-A1 1
Operation and effect of:

 roll control: ailerons and spoilers;
 pitch control: elevators, stabilators, variable incidence stabilisers and canards;
 yaw control, rudder limiters;
Control using elevons, ruddervators;
High lift devices, slots, slats, flaps, flaperons;
Drag inducing devices, spoilers, lift dumpers, speed brakes;
Effects of wing fences, saw tooth leading edges;
Boundary layer control using, vortex generators, stall wedges or leading edge devices;
Operation and effect of trim tabs, balance and antibalance (leading) tabs, servo tabs, spring tabs, mass
balance, control surface bias, aerodynamic balance panels.
11A.1.2. High Speed flight AG-11A-01-02-A1 1
157
Speed of sound, subsonic flight, transonic flight, supersonic flight,

Mach number, critical Mach number, compressibility buffet, shock wave, aerodynamic heating, area rule;
Factors affecting airflow in engine intakes of high speed aircraft;
Effects of sweepback on critical Mach number.
11A.2. AIRFRAME STRUCTURES – GENERAL CONCEPTS
(a) AG-11A-02a-A1-B11 2
Airworthiness requirements for structural strength;

Structural classification, primary, secondary and tertiary;
Fail safe, safe life, damage tolerance concepts;
Zonal and station identification systems;
Stress, strain, bending, compression, shear, torsion, tension, hoop stress, fatigue;
Drains and ventilation provisions;
System installation provisions;
Lightning strike protection provision;
Aircraft bonding.
(b) AG-11A-02a-A1 1
Construction methods of: stressed skin fuselage, formers, stringers, longerons, bulkheads, frames,
doublers, struts, ties, beams, floor structures, reinforcement, methods of skinning, anti-corrosive
protection, wing, empennage and engine attachments;
Structure assembly techniques: riveting, bolting, bonding
Methods of surface protection, such as chromating, anodising, painting ;
Surface cleaning;
Airframe symmetry: methods of alignment and symmetry checks.
158
11A.3. AIRFRAME STRUCTURES – AEROPLANES
11A.3.1. Fuselage (ATA 52/53/56) AG-11A-03-01-A1 1
Construction and pressurisation sealing;

Wing, stabiliser, pylon and under carriage attachments;
Seat installation and cargo loading system;
Doors and emergency exits : construction, mechanisms, operation and safety devices ;
Windows and windscreen construction and mechanisms.
11A.3.2. Wings (ATA 57) AG-11A-03-02-A1 1
Construction;
Fuel storage;
Landing gear, pylon, control surface and high lift/drag attachments.
11A.3.3. Stabilizers (ATA 55) AG-11A-03-03-A1 1
Construction;
Control surface attachment.
11A.3.4. Flight Control Surfaces (ATA 55/57) AG-11A-03-04-A1 1
Construction and attachment;

Balancing – mass and aerodynamic.
11A.3.5. Nacelles/Pylons (ATA 54) AG-11A-03-05-A1 1
159
Construction;
Firewalls;
Engine mounts.
11A.4. AIR CONDITIONING AND CABIN PRESSURIZATION (ATA 21)
11A.4.1. Air supply AG-11A-04-01-A1 1
Sources of air supply including engine bleed, APU and ground cart.
11A.4.2. Air conditioning AG-11A-04-02-A1 1
Air conditioning systems;

Air cycle and vapour cycle machines;
Distribution systems;
Flow, temperature and humidity control system.
11A.4.3. Pressurization AG-11A-04-03-A1 1
Pressurisation systems;
Control and indication including control and safety valves;
Cabin pressure controllers.
11A.4.4. Safety and warning devices AG-11A-04-04-A1 1
Protection and warning devices.
11A.5. INSTRUMENT/AVIONIC SYSTEMS
11A.5.1. Instrument Systems (ATA 31) AG-11A-05-01-A1 1
160
Pitot static: altimeter, air speed indicator, vertical speed indicator;

Gyroscopic: artificial horizon, attitude director, direction indicator, horizontal situation indicator, turn and
slip indicator, turn coordinator;
Compasses: direct reading, remote reading;
Angle of attack indication, stall warning systems;
Glass cockpit;
Other aircraft system indication.
11A.5.2. Avionic Systems AG-11A-05-01-A1-B11 1
Fundamentals of system lay-outs and operation of:

 Auto Flight (ATA 22);
 Communications (ATA 23);
 Navigation Systems (ATA 34).
11A.6. ELECTRICAL POWER
Batteries installation and operation; AG-11A-06-A1 1

DC power generation;
AC power generation;
Emergency power generation;
Voltage regulation;
Power distribution;
Inverters, transformers, rectifiers;
Circuit protection;
External / Ground power
161
11A.7. EQUIPMENT AND FURNISHINGS (ATA 25)
(a) AG-11A-07a-A1-B11 2
Emergency equipment requirements;

Seats, harnesses and belts.
(b) AG-11A-07a-A1-B11 1
Cabin lay-out;
Equipment lay-out;
Cabin Furnishing Installation;
Cabin entertainment equipment;
Galley installation;
Cargo handling and retention equipment;
Airstairs.
11A.8. FIRE PROTECTION (ATA 26)
(a) AG-11A-08a-A1 1
Fire and smoke detection and warning systems;

Fire extinguishing systems;
System tests.
(b) AG-11A-08b-A1-B11 1
Portable fire extinguisher.
11A.9. FLIGHT CONTROLS (ATA 27)
162
Primary controls: aileron, elevator, rudder, spoiler; AG-11A-09-A1 1

Trim control;
Active load control;
High lift devices;
Lift dump, speed brakes;
System operation: manual, hydraulic, pneumatic, electrical, fly-by-wire;
Artificial feel, Yaw damper, Mach trim, rudder limiter, gust locks systems;
Balancing and rigging;
Stall protection / warning system.
11A.10. FUEL SYSTEMS (ATA 28)
System lay-out; AG-11A-10-A1 1

Fuel tanks;
Supply systems;
Dumping, venting and draining;
Cross-feed and transfer;
Indications and warnings;
Refuelling and defuelling;
Longitudinal balance fuel systems.
11A.11. HYDRAULIC POWER (ATA 29)
163

Hydraulic fluids;
Hydraulic reservoirs and accumulators;
Pressure generation: electric, mechanical, pneumatic;
Emergency pressure generation;
Filters;
Pressure Control;
Power distribution;
Indication and warning systems;
Interface with other systems.
11A.12. ICE AND RAIN PROTECTION (ATA 30)
Ice formation, classification and detection; AG-11A-12-A1 1

Anti-icing systems: electrical, hot air and chemical;
De-icing systems: electrical, hot air, pneumatic and chemical ;
Rain repellent;
Probe and drain heating;
Wiper systems.
11A.13. LANDING GEAR (ATA 32)
164
Construction, shock absorbing; AG-11A-13-A1 2

Extension and retraction systems: normal and emergency;
Indications and warning;
Wheels, brakes, antiskid and auto braking;
Tyres;
Steering;
Air-ground sensing.
11A.14. LIGHTS (ATA 33)
External: navigation, anti-collision, landing, taxiing, ice; AG-11A-14-A1 2

Internal: cabin, cockpit, cargo;
Emergency.
11A.15. OXYGEN (ATA 35)
System lay-out: AG-11A-15-A1 1

 cockpit,
 cabin;
Sources, storage, charging and distribution;
Supply regulation;
Indications and warnings.
11A.16. PNEUMATIC/VACUUM (ATA 36)
165

Sources:
 engine / APU,
 compressors,
 reservoirs,
 ground supply;
Pressure and vacuum pumps;
Pressure control;
Distribution;
Interfaces with other systems.
11A.17. WATER/WASTE (ATA 38)
Water system lay-out, supply, distribution, servicing and draining; AG-11A-17-A1 2

Toilet system lay-out, flushing and servicing;
Corrosion aspects.
11A.18. ON BOARD MAINTENANCE SYSTEMS (ATA 45)
Central maintenance computers; AG-11A-18-A1 1

Data loading system;
Electronic library system;
Printing;
Structure monitoring (damage tolerance monitoring).
11A.19. INTEGRATED MODULAR AVIONICS (ATA 42)
166
Functions that may be typically integrated in the Integrated Modular Avionic (IMA) modules are, among AG-11A-19-A1 1
others:
 Bleed management,
 Air pressure control,
 Air ventilation and control,
 Avionics and cockpit ventilation control,
 Temperature control,
 Air traffic communication,
 Avionics communication router,
 Electrical load management,
 Circuit breaker monitoring,
 Electrical system BITE,
 Fuel management,
 Braking control,
 Steering control,
 Landing gear extension and retraction,
 Tyre pressure indication,
 Oleo pressure indication,
 Brake temperature monitoring, etc.
Core system;
Network components.
11A.20. CABIN SYSTEMS (ATA 44)
167
The units and components which furnish a means of entertaining the passengers and providing AG-11A-20-A1 1
communication within the aircraft (Cabin Intercommunication Data System) and between the aircraft
cabin and ground stations (Cabin Network Service). Includes voice, data, music and video
transmissions.
The Cabin Intercommunication Data System provides an interface between cockpit/cabin crew and
cabin systems. These systems support data exchange of the different related LRU’s and they are
typically operated via Flight Attendant Panels.
The Cabin Network Service typically consists on a server, typically interfacing with, among others, the
following systems:
 Data/Radio Communication, In-Flight Entertainment System.
The Cabin Network Service may host functions such as:
 Access to pre-departure/departure reports,
 E-mail/intranet/Internet access,
 Passenger database;
Cabin Core System;
In-flight Entertainment System;
External Communication System;
Cabin Mass Memory System;
Cabin Monitoring System;
Miscellaneous Cabin System.
11A.21. INFORMATION SYSTEMS (ATA 46)
168
The units and components which furnish a means of storing, updating and retrieving digital information AG-11A-21-A1 1
traditionally provided on paper, microfilm or microfiche. Includes units that are dedicated to the
information storage and retrieval function such as the electronic library mass storage and controller.
Does not include units or components installed for other uses and shared with other systems, such as
flight deck printer or general use display.
Typical examples include Air Traffic and Information Management Systems and Network Server
Systems
Aircraft General Information System;
Flight Deck Information System;
Maintenance Information System;
Passenger Cabin Information System;
Miscellaneous Information System.
169
MODULE 11A. TURBINE AEROPLANE AERODYNAMICS, STRUCTURES AND

SYSTEMS – B1.1 CATEGORY
11A.1. THEORY OF FLIGHT
11A.1.1. Aeroplane Aerodynamics and Flight controls AG-11A-01-01-B11 2

11A.1.2. High Speed flight AG-11A-01-02-B11 2
170
Speed of sound, subsonic flight, transonic flight, supersonic flight,

Mach number, critical Mach number, compressibility buffet, shock wave, aerodynamic heating, area rule;
Factors affecting airflow in engine intakes of high speed aircraft;
Effects of sweepback on critical Mach number.
11A.2. AIRFRAME STRUCTURES – GENERAL CONCEPTS
(a) AG-11A-02a-A1-B11 2

Aircraft bonding.
(b) AG-11A-02A1-B11 2
Surface cleaning;
171
11A.3. AIRFRAME STRUCTURES – AEROPLANES
11A.3.1. Fuselage (ATA 52/53/56) AG-11A-03-01-B11 2

11A.3.2. Wings (ATA 57) AG-11A-03-02-B11 2
Construction;
Fuel storage;
11A.3.3. Stabilizers (ATA 55) AG-11A-03-03-B11 2
Construction;
11A.3.4. Flight Control Surfaces (ATA 55/57) AG-11A-03-04-B11 2

11A.3.5. Nacelles/Pylons (ATA 54) AG-11A-03-05-B11 2
172
Construction;
Firewalls;
Engine mounts.
11A.4. AIR CONDITIONING AND CABIN PRESSURIZATION (ATA 21)
11A.4.1. Air supply AG-11A-04-01-B11 2
11A.4.2. Air conditioning AG-11A-04-02-B11 3

11A.4.3. Pressurization AG-11A-04-03-B11 3
11A.4.4. Safety and warning devices AG-11A-04-04-B11 3
11A.5. INSTRUMENT/AVIONIC SYSTEMS
11A.5.1. Instrument Systems (ATA 31) AG-11A-05-01-B11 2
173

Glass cockpit;
11A.5.2. Avionic Systems AG-11A-05-01-A1-B11 1

11A.6. ELECTRICAL POWER
Batteries installation and operation; AG-11A-06-B11 3

Voltage regulation;
Power distribution;
Circuit protection;
174
11A.7. EQUIPMENT AND FURNISHINGS (ATA 25)
(a) AG-11A-07a-A1-B11 2

(b) AG-11A-07a-A1-B11 1
Cabin lay-out;
Equipment lay-out;
Airstairs.
11A.8. FIRE PROTECTION (ATA 26)
(a) AG-11A-08A1-B11 3

System tests.
(b) AG-11A-08b-A1-B11 1
11A.9. FLIGHT CONTROLS (ATA 27)
175
Primary controls: aileron, elevator, rudder, spoiler; AG-11A-09-B11 3

Trim control;
High lift devices;
11A.10. FUEL SYSTEMS (ATA 28)
System lay-out; AG-11A-10-B11 3

Fuel tanks;
Supply systems;
11A.11. HYDRAULIC POWER (ATA 29)
176

Hydraulic fluids;
Filters;
Pressure Control;
Power distribution;
11A.12. ICE AND RAIN PROTECTION (ATA 30)
Ice formation, classification and detection; AG-11A-12-B11 3

Rain repellent;
Wiper systems.
11A.13. LANDING GEAR (ATA 32)
177
Construction, shock absorbing; AG-11A-13-B11 3

Tyres;
Steering;
Air-ground sensing.
11A.14. LIGHTS (ATA 33)
External: navigation, anti-collision, landing, taxiing, ice; AG-11A-14-B11 3

Emergency.
11A.15. OXYGEN (ATA 35)
System lay-out: AG-11A-15-B11 3

 cockpit,
 cabin;
Supply regulation;
11A.16. PNEUMATIC/VACUUM (ATA 36)
178

Sources:
 engine / APU,
 compressors,
 reservoirs,
 ground supply;
Pressure control;
Distribution;
11A.17. WATER/WASTE (ATA 38)
Water system lay-out, supply, distribution, servicing and draining; AG-11A-17-B11 3

Corrosion aspects.
11A.18. ON BOARD MAINTENANCE SYSTEMS (ATA 45)
Central maintenance computers; AG-11A-18-B11 2

Printing;
11A.19. INTEGRATED MODULAR AVIONICS (ATA 42)
179
Functions that may be typically integrated in the Integrated Modular Avionic (IMA) modules are, among AG-11A-19-B11 2
others:
Core system;
Network components.
11A.20. CABIN SYSTEMS (ATA 44)
180
The units and components which furnish a means of entertaining the passengers and providing AG-11A-20-B11 2
transmissions.
following systems:
Cabin Core System;
11A.21. INFORMATION SYSTEMS (ATA 46)
181
The units and components which furnish a means of storing, updating and retrieving digital information AG-11A-21-B11 2
Systems
182
MODULE 11B. PISTON AEROPLANE AERODYNAMICS, STRUCTURES AND

SYSTEMS – A2 CATEGORY
11B.1. THEORY OF FLIGHT
11B.1.1. Aeroplane Aerodynamics and Flight controls AG-11B-01-01-A2 1

11B.1.2. High Speed Flight N/A
183
11B.2. AIRFRAME STRUCTURES – GENERAL CONCEPTS
(a) AG-11B-02a-A2-B12 2

Aircraft bonding.
(b) AG-11B-02A2 1
Surface cleaning;
11B.3. AIRFRAME STRUCTURES – AEROPLANES
11B.3.1. Fuselage (ATA 52/53/56) AG-11B-03-01-A2 1
184

11B.3.2. Wings (ATA 57) AG-11B-03-02-A2 1
Construction;
Fuel storage;
11B.3.3. Stabilizers (ATA 55) AG-11B-03-03-A2 1
Construction;
11B.3.4. Flight Control Surfaces (ATA 55/57) AG-11B-03-04-A2 1

11B.3.5. Nacelles/Pylons (ATA 54) AG-11B-03-05-A2 1
Construction;
Firewalls;
Engine mounts.
11B.4. AIR CONDITIONING AND CABIN PRESSURIZATION (ATA 21)
185
Pressurisation and air conditioning systems; AG-11B-04-01-A2 1

Cabin pressure controllers, protection and warning devices;
Heating systems.
11B.5. INSTRUMENT/AVIONIC SYSTEMS
11B.5.1. Instrument Systems (ATA 31) AG-11B-05-01-A2 1

Glass cockpit;
11B.5.2. Avionic Systems AG-11B-05-01-A2-B12 1

11B.6. ELECTRICAL POWER
186
Batteries installation and operation; AG-11B-06-A2 1

Voltage regulation;
Power distribution;
Circuit protection;
11B.7. EQUIPMENT AND FURNISHINGS (ATA 25)
(a) AG-11B-07a-A2-B12 2

(b) AG-11B-07a-A2-B12 1
Cabin lay-out;
Equipment lay-out;
Airstairs.
11B.8. FIRE PROTECTION (ATA 26)

187
(a) AG-11B-08-A2 1

System tests.
(b) AG-11B-08b-A2 1
11B.9. FLIGHT CONTROLS (ATA 27)
Primary controls: aileron, elevator, rudder, spoiler; AG-11B-09-A2 1

Trim control;
High lift devices;
11B.10. FUEL SYSTEMS (ATA 28)
188
System lay-out; AG-11B-10-A2 1

Fuel tanks;
Supply systems;
11B.11. HYDRAULIC POWER (ATA 29)

Hydraulic fluids;
Filters;
Pressure Control;
Power distribution;
11B.12. ICE AND RAIN PROTECTION (ATA 30)
189
Ice formation, classification and detection; AG-11B-12-A2 1

Rain repellent;
Wiper systems.
11B.13. LANDING GEAR (ATA 32)
Construction, shock absorbing; AG-11B-13-A2 2

Tyres;
Steering;
Air-ground sensing.
11B.14. LIGHTS (ATA 33)
External: navigation, anti-collision, landing, taxiing, ice; AG-11B-14-A2 2

Emergency.
11B.15. OXYGEN (ATA 35)
190
System lay-out: AG-11B-15-A2 1

 cockpit,
 cabin;
Supply regulation;
11B.16. PNEUMATIC/VACUUM (ATA 36)

Sources:
 engine / APU,
 compressors,
 reservoirs,
 ground supply;
Pressure control;
Distribution;
11B.17. WATER/WASTE (ATA 38)
Water system lay-out, supply, distribution, servicing and draining; AG-11B-17-A2 2

Corrosion aspects.
191
192
MODULE 11B. PISTON AEROPLANE AERODYNAMICS, STRUCTURES AND

SYSTEMS – B1.2 CATEGORY
11B.1. THEORY OF FLIGHT
11B.1.1. Aeroplane Aerodynamics and Flight controls AG-11B-01-01-B12 2

11B.1.2. High Speed Flight N/A
193
11B.2. AIRFRAME STRUCTURES – GENERAL CONCEPTS
(a) AG-11B-02a-A2-B12 2

Aircraft bonding.
(b) AG-11B-02A2-B12 2
Surface cleaning;
11B.3. AIRFRAME STRUCTURES – AEROPLANES
11B.3.1. Fuselage (ATA 52/53/56) AG-11B-03-01-B12 2
194

11B.3.2. Wings (ATA 57) AG-11B-03-02-B12 2
Construction;
Fuel storage;
11B.3.3. Stabilizers (ATA 55) AG-11B-03-03-B12 2
Construction;
11B.3.4. Flight Control Surfaces (ATA 55/57) AG-11B-03-04-B12 2

11B.3.5. Nacelles/Pylons (ATA 54) AG-11B-03-05-B12 2
Construction;
Firewalls;
Engine mounts.
11B.4. AIR CONDITIONING AND CABIN PRESSURIZATION (ATA 21)
195
Pressurisation and air conditioning systems; AG-11B-04-01-B12 3

Cabin pressure controllers, protection and warning devices;
Heating systems.
11B.5. INSTRUMENT/AVIONIC SYSTEMS
11B.5.1. Instrument Systems (ATA 31) AG-11B-05-01-B12 2

Glass cockpit;
11B.5.2. Avionic Systems AG-11B-05-01-A2-B12 1

11B.6. ELECTRICAL POWER
196
Batteries installation and operation; AG-11B-06-B12 3

Voltage regulation;
Power distribution;
Circuit protection;
11B.7. EQUIPMENT AND FURNISHINGS (ATA 25)
(a) AG-11B-07a-A2-B12 2

(b) AG-11B-07a-A2-B12 1
Cabin lay-out;
Equipment lay-out;
Airstairs.
11B.8. FIRE PROTECTION (ATA 26)

197
(a) AG-11B-08-B12 3

System tests.
(b) AG-11B-08b-B12 3
11B.9. FLIGHT CONTROLS (ATA 27)
Primary controls: aileron, elevator, rudder, spoiler; AG-11B-09-B12 3

Trim control;
High lift devices;
11B.10. FUEL SYSTEMS (ATA 28)
198
System lay-out; AG-11B-10-B12 3

Fuel tanks;
Supply systems;
11B.11. HYDRAULIC POWER (ATA 29)

Hydraulic fluids;
Filters;
Pressure Control;
Power distribution;
11B.12. ICE AND RAIN PROTECTION (ATA 30)
199
Ice formation, classification and detection; AG-11B-12-B12 3

Rain repellent;
Wiper systems.
11B.13. LANDING GEAR (ATA 32)
Construction, shock absorbing; AG-11B-13-B12 3

Tyres;
Steering;
Air-ground sensing.
11B.14. LIGHTS (ATA 33)
External: navigation, anti-collision, landing, taxiing, ice; AG-11B-14-B12 3

Emergency.
11B.15. OXYGEN (ATA 35)
200
System lay-out: AG-11B-15-B12 3

 cockpit,
 cabin;
Supply regulation;
11B.16. PNEUMATIC/VACUUM (ATA 36)

Sources:
 engine / APU,
 compressors,
 reservoirs,
 ground supply;
Pressure control;
Distribution;
11B.17. WATER/WASTE (ATA 38)
Water system lay-out, supply, distribution, servicing and draining; AG-11B-17-B12 3

Corrosion aspects.
201
202
MODULE 11C. PISTON AEROPLANE AERODYNAMICS, STRUCTURES AND

SYSTEMS – B3 CATEGORY
11C.1. THEORY OF FLIGHT
Operation and effect of: AG-11C-01-B3 1

11C.2. AIRFRAME STRUCTURES – GENERAL CONCEPTS
(a) AG-11C-02-B3 2
203

Aircraft bonding.
(b) AG-11C-02-B3 2
Surface cleaning;
11C.3. AIRFRAME STRUCTURES – AEROPLANES
11C.3.1. Fuselage (ATA 52/53/56) AG-11C-03-01-B3 1
204

11C.3.2. Wings (ATA 57) AG-11C-03-02-B3 1
Construction;
Fuel storage;
11C.3.3. Stabilizers (ATA 55) AG-11C-03-03-B3 1
Construction;
11C.3.4. Flight Control Surfaces (ATA 55/57) AG-11C-03-04-B3 1

11C.3.5. Nacelles/Pylons (ATA 54) AG-11C-03-05-B3 1
Construction;
Firewalls;
Engine mounts.
11C.4. AIR CONDITIONING (ATA 21)
205
Heating and ventilation systems AG-11C-04-B3 1
11C.5. INSTRUMENT/AVIONIC SYSTEMS
11C.5.1. Instrument Systems (ATA 31) AG-11C-05-01-B3 1

Glass cockpit;
11C.5.2. Avionic Systems AG-11C-05-01-B3 1

11C.6. ELECTRICAL POWER
206
Batteries installation and operation; AG-11C-06-B3 2

Voltage regulation;
Power distribution;
Circuit protection;
11C.7. EQUIPMENT AND FURNISHINGS (ATA 25)
Emergency equipment requirements; AG-11C-07-B3 2

11C.8. FIRE PROTECTION (ATA 26)
Portable fire extinguisher. AG-11C-08-B3 2
11C.9. FLIGHT CONTROLS (ATA 27)
207
Primary controls: aileron, elevator, rudder, spoiler; AG-11C-09-B3 3

Trim control;
High lift devices;
11C.10. FUEL SYSTEMS (ATA 28)
System lay-out; AG-11C-10-B3 2

Fuel tanks;
Supply systems;
11C.11. HYDRAULIC POWER (ATA 29)
208

Hydraulic fluids;
Filters;
Pressure Control;
Power distribution;
11C.12. ICE AND RAIN PROTECTION (ATA 30)
Ice formation, classification and detection; AG-11C-12-B3 1

Rain repellent;
Wiper systems.
11C.13. LANDING GEAR (ATA 32)
209
Construction, shock absorbing; AG-11C-13-B3 2

Tyres;
Steering;
Air-ground sensing.
11C.14. LIGHTS (ATA 33)
External: navigation, anti-collision, landing, taxiing, ice; AG-11C-14-B3 2

Emergency.
11C.15. OXYGEN (ATA 35)
System lay-out: AG-11C-15-B3 2

 cockpit,
 cabin;
Supply regulation;
11.16. PNEUMATIC/VACUUM (ATA 36)
210

Sources:
 engine / APU,
 compressors,
 reservoirs,
 ground supply;
Pressure control;
Distribution;
211
Module 12
HELICOPTER AERODYNAMICS,
STRUCTURES AND SYSTEMS
212
MODULE 12. HELICOPTER AERODYNAMICS, STRUCTURES AND SYSTEMS –

A3 & A4 CATEGORIES
12.1. THEORY OF FLIGHT – ROTARY WING AERODYNAMICS
Terminology; AG-12-01-A3-A4 1
Effects of gyroscopic precession;
Torque reaction and directional control;
Dissymmetry of lift, Blade tip stall;
Translating tendency and its correction;
Coriolis effect and compensation;
Vortex ring state, power settling, overpitching;
Auto-rotation;
Ground effect.
12.2. FLIGHT CONTROL SYSTEMS
213
Cyclic control; AG-12-02-A3-A4 2

Collective control;
Swashplate;
Yaw control: Anti-Torque Control, Tail rotor, bleed air;
Main Rotor Head: Design and Operation features;
Blade Dampers: Function and construction;
Rotor Blades: Main and tail rotor blade construction and attachment;
Trim control, fixed and adjustable stabilisers;
System operation: manual, hydraulic, electrical and fly-by-wire;
Artificial feel;
Balancing and rigging.
12.3. BLADE TRACKING AND VIBRATION ANALYSIS
Rotor alignment; AG-12-03-A3-A4 1

Main and tail rotor tracking;
Static and dynamic balancing;
Vibration types, vibration reduction methods;
Ground resonance.
12.4. TRANSMISSION
Gear boxes, main and tail rotors; AG-12-04-A3-A4 1

Clutches, free wheel units and rotor brake;
Tail rotor drive shafts, flexible couplings, bearings, vibration dampers and bearing hangers.
12.5. AIRFRAME STRUCTURES
214
(a) AG-12-05a-A3-A4-B1 2

Lightning strike protection provision.
(b) AG-12-05b-A3-A4 1
215
doublers, struts, ties, beams, floor structures, reinforcement, methods of skinning and anti-corrosive
protection;
Pylon, stabiliser and undercarriage attachments;
Seat installation;
Doors: construction, mechanisms, operation and safety devices;
Windows and windscreen construction;
Fuel storage;
Firewalls;
Engine mounts;
Structure assembly techniques: riveting, bolting, bonding;
Methods of surface protection, such as chromating, anodising, painting;
Surface cleaning;
12.6. AIR CONDITIONING (ATA 21)
12.6.1. Air Supply AG-12-06-01-A3-A4 1
Sources of air supply including engine bleed and ground cart.
12.6.2. Air Conditioning AG-12-06-02-A3-A4 1

Flow and temperature control systems;
216
12.7. INSTRUMENTS – AVIONIC SYSTEMS
12.7.1. Instrument Systems (ATA 31) AG-12-07-01-B1 2

Vibration indicating systems — HUMS;
Glass cockpit;
12.7.2. Avionic Systems (ATA 31) AG-12-07-02-A3-A4-B1 1
Fundamentals of system layouts and operation of:

12.8. ELECTRICAL POWER (ATA 24)
Batteries Installation and Operation; AG-12-08-A3-A4 1

DC power generation, AC power generation;
Voltage regulation, Circuit protection.
Power distribution;
External/Ground power.
217
12.9. EQUIPMENT AND FURNISHINGS (ATA 25)
(a) AG-12-09a-A3-A4-B1 2

Seats, harnesses and belts;
Lifting systems.
(b) AG-12-09a-A3-A4-B1 1
Emergency flotation systems;

Cabin lay-out, cargo retention;
Equipment lay-out;
Cabin furnishing installation.
12.10. FIRE PROTECTION (ATA 26)
Fire and smoke detection and warning systems; AG-12-10-A3-A4 1

System tests.
12.11. FUEL SYSTEMS (ATA 28)
218
System lay-out; AG-12-11-A3-A4 1

Fuel tanks;
Supply systems;
Refuelling and defuelling.
12.12. HYDRAULIC POWER (ATA 29)

Hydraulic fluids;
Filters;
Pressure control;
Power distribution;
12.13. ICE AND RAIN PROTECTION (ATA 30)
219
Ice formation, classification and detection; AG-12-13-A3-A4 1

Anti-icing and De-icing systems: electrical, hot air and chemical;
Rain repellent and removal;
Wiper system.
12.14. LANDING GEARS (ATA 32)
Construction, shock absorbing; AG-12-14-A3-A4 2

Wheels, Tyres, brakes;
Steering;
Air-ground sensing;
Skids, floats.
12.15. LIGHTS (ATA 33)
External: navigation, landing, taxiing, ice; AG-12-15-A3-A4 2

Emergency.
220

Sources: engine/APU, compressors, reservoirs, ground supply;
Pressure control;
Distribution;
12.17. INTEGRATED MODULAR AVIONICS (ATA 42)
221
Functions that may be typically integrated in the Integrated Modular Avionic (IMA) modules are, among AG-12-17-A3-A4 1
others:
Core system;
Network components.
12.18. ON BOARD MAINTENANCE (ATA 45)
222
Central maintenance computers; AG-12-18-A3-A4 1

Printing;
12.19. INFORMATION SYSTEMS (ATA 46)
The units and components which furnish a means of storing, updating and retrieving digital information AG-12-19-A3-A4 1
Systems
223
MODULE 12. HELICOPTER AERODYNAMICS, STRUCTURES AND SYSTEMS –

B1.3 & B1.4 CATEGORIES
12.1. THEORY OF FLIGHT – ROTARY WING AERODYNAMICS
Terminology; AG-12-01-B13-B14 3
Effects of gyroscopic precession;
Torque reaction and directional control;
Dissymmetry of lift, Blade tip stall;
Translating tendency and its correction;
Coriolis effect and compensation;
Vortex ring state, power settling, overpitching;
Auto-rotation;
Ground effect.
12.2. FLIGHT CONTROL SYSTEMS
224
Cyclic control; AG-12-02-B13-B14 3

Collective control;
Swashplate;
Yaw control: Anti-Torque Control, Tail rotor, bleed air;
Main Rotor Head: Design and Operation features;
Blade Dampers: Function and construction;
Rotor Blades: Main and tail rotor blade construction and attachment;
Trim control, fixed and adjustable stabilisers;
System operation: manual, hydraulic, electrical and fly-by-wire;
Artificial feel;
Balancing and rigging.
12.3. BLADE TRACKING AND VIBRATION ANALYSIS
Rotor alignment; AG-12-03-B13-B14 3

Main and tail rotor tracking;
Static and dynamic balancing;
Vibration types, vibration reduction methods;
Ground resonance.
12.4. TRANSMISSION
Gear boxes, main and tail rotors; AG-12-04-B13-B14 3

Clutches, free wheel units and rotor brake;
Tail rotor drive shafts, flexible couplings, bearings, vibration dampers and bearing hangers.
12.5. AIRFRAME STRUCTURES
225
(a) AG-12-05a-A-B13-B14 2

(b) AG-12-05b-B13-B14 2
226
doublers, struts, ties, beams, floor structures, reinforcement, methods of skinning and anti-corrosive
protection;
Pylon, stabiliser and undercarriage attachments;
Seat installation;
Doors: construction, mechanisms, operation and safety devices;
Windows and windscreen construction;
Fuel storage;
Firewalls;
Engine mounts;
Structure assembly techniques: riveting, bolting, bonding;
Methods of surface protection, such as chromating, anodising, painting;
Surface cleaning;
12.6. AIR CONDITIONING (ATA 21)
12.6.1. Air Supply AG-12-06-01-B13-B14 2
Sources of air supply including engine bleed and ground cart.
12.6.2. Air Conditioning AG-12-06-02-B13-B14 3

Flow and temperature control systems;
227
12.7. INSTRUMENTS – AVIONIC SYSTEMS
12.7.1. Instrument Systems (ATA 31) AG-12-07-01-B13-B14 2

Vibration indicating systems — HUMS;
Glass cockpit;
12.7.2. Avionic Systems (ATA 31) AG-12-07-02-A-B13-B14 1
Fundamentals of system layouts and operation of:

Batteries Installation and Operation; AG-12-08-B13-B14 3

DC power generation, AC power generation;
Voltage regulation, Circuit protection.
Power distribution;
228
12.9. EQUIPMENT AND FURNISHINGS (ATA 25)
(a) AG-12-09a-A-B13-B14 2

Seats, harnesses and belts;
Lifting systems.
(b) AG-12-09a-A-B13-B14 1
Emergency flotation systems;

Cabin lay-out, cargo retention;
Equipment lay-out;
Cabin furnishing installation.
12.10. FIRE PROTECTION (ATA 26)
Fire and smoke detection and warning systems; AG-12-10-B13-B14 3

System tests.
12.11. FUEL SYSTEMS (ATA 28)
229
System lay-out; AG-12-11-B13-B14 3

Fuel tanks;
Supply systems;
Refuelling and defuelling.
12.12. HYDRAULIC POWER (ATA 29)

Hydraulic fluids;
Filters;
Pressure control;
Power distribution;
12.13. ICE AND RAIN PROTECTION (ATA 30)
230
Ice formation, classification and detection; AG-12-13-B13-B14 3

Anti-icing and De-icing systems: electrical, hot air and chemical;
Rain repellent and removal;
Wiper system.
12.14. LANDING GEARS (ATA 32)
Construction, shock absorbing; AG-12-14-B13-B14 3

Wheels, Tyres, brakes;
Steering;
Air-ground sensing;
Skids, floats.
12.15. LIGHTS (ATA 33)
External: navigation, landing, taxiing, ice; AG-12-15-B13-B14 3

Emergency.
231

Sources: engine/APU, compressors, reservoirs, ground supply;
Pressure control;
Distribution;
232
Functions that may be typically integrated in the Integrated Modular Avionic (IMA) modules are, among AG-12-17-B13-B14 2
others:
Core system;
Network components.
12.18. ON BOARD MAINTENANCE (ATA 45)
233
Central maintenance computers; AG-12-18-B13-B14 2

Printing;
12.19. INFORMATION SYSTEMS (ATA 46)
The units and components which furnish a means of storing, updating and retrieving digital information AG-12-19-B13-B14 2
Systems
234
Module 13
AIRCRAFT AERODYNAMICS,
STRUCTURES AND SYSTEMS
235
MODULE 13. AIRCRAFT AERODYNAMICS, STRUCTURES AND SYSTEMS –

B2 CATEGORY
(a) Aeroplane aerodynamics and flight controls AG-13-01a-B2 1

 roll control: ailerons and spoilers,
 pitch control: elevators, stabilators, variable incidence stabilisers and canards,
High lift devices: slots, slats, flaps;
Drag inducing devices: spoilers, lift dumpers, speed brakes;
Operation and effect of trim tabs, servo tabs, control surface bias.
(b) High speed flight AG-13-01b-B2 1
Speed of sound, subsonic flight, transonic flight, super sonic flight,

Mach number, critical Mach number.
236
(c) Rotary wing aerodynamics AG-13-01c-B2 1
Terminology;
Operation and effect of cyclic, collective and anti-torque controls.
13.2. STRUCTURES – GENERAL CONCEPTS
(a) AG-13-02a-B2 1
Fundamentals of structural systems.
(b) AG-13-02a-B2 1

Electrical bonding;
13.3. AUTOFLIGHT (ATA 22)
Fundamentals of automatic flight control including working principles and current terminology; AG-13-03-B2 3
Command signal processing;
Modes of operation: roll, pitch and yaw channels;
Yaw dampers;
Stability Augmentation System in helicopters;
Automatic trim control;
Autopilot navigation aids interface;
Autothrottle systems.
Automatic landing systems: principles and categories, modes of operation, approach, glideslope, land,
go-around, system monitors and failure conditions.
237
13.4. COMMUNICATION / NAVIGATION (ATA 23 / 34)
238
Fundamentals of radio wave propagation, antennas, transmission lines, communication, receiver and AG-13-04-B2 3
transmitter;
Working principles of following systems;
Very High Frequency (VHF) communication;
High Frequency (HF) communication;
Audio;
Emergency Locator Transmitters;
Cockpit Voice Recorder;
Very High Frequency omni directional range (VOR);
Automatic Direction Finding (ADF);
Instrument Landing System (ILS);
Microwave Landing System (MLS);
Very Low Frequency and hyperbolic navigation (VLF/Omega);
Doppler navigation;
Flight Director systems; Distance Measuring Equipment (DME);
Area navigation, RNAV systems;
Hyperbolic navigation systems
Flight Management Systems (FMS) and ARINC communication and reporting(ACARS).
Global Positioning System (GPS), Global Navigation Satellite Systems(GNSS);
Inertial Navigation System;
Radar
Air Traffic Control transponder, secondary surveillance radar;
Weather avoidance radar;
Traffic Alert and Collision Avoidance System (TCAS);
Radio altimeter;
239
Batteries installation and operation; AG-13-05-B2 3

Voltage regulation; Power distribution;
Circuit protection;
13.6 EQUIPMENT AND FURNISHINGS (ATA 25)
Electronic emergency equipment requirements; AG-13-06-B2 3

Cabin entertainment equipment.
13.7 FLIGHT CONTROLS (ATA 27)
(a) AG-13-07a-B2 1
Primary controls: aileron, elevator, rudder, spoiler;

Trim control;
High lift devices;
System operation: manual, hydraulic, pneumatic; Artificial feel;
Yaw damper, Mach trim, rudder limiter, gust locks. Stall protection systems.
240
(b)
System operation: electrical, fly by wire. AG-13-07b-B2 2
13.8 INSTRUMENT SYSTEMS (ATA 31)
241
Classification; Atmosphere; Terminology; AG-13-08-B2 3

Pressure measuring devices and systems;
Pitot static systems;
Altimeters;
Vertical speed indicators;
Air speed indicators;
Machmeters;
Altitude reporting / alerting systems;
Air data computers;
Instrument pneumatic systems;
Direct reading pressure and temperature gauges;
Temperature indicating systems;
Fuel quantity indicating systems;
Gyroscopic principles;
Artificial horizons;
Slip indicators;
Directional gyros;
Ground Proximity Warning Systems;
Compass systems;
Electronic Flight Instrument Systems
Instrument warning systems including master warning systems and centralised warning panels;
Stall warning systems and angle of attack indicating systems;
Vibration measurement and indication.
Glass cockpit.
242
13.9 LIGHTS (ATA 33)
External: navigation, landing, taxiing, ice; AG-13-09-B2 3

Emergency.
13.10 ON BOARD MAINTENANCE SYSTEMS (ATA 45)
Central maintenance computers; AG-13-10-B2 3

Printing;
13.11 AIR CONDITIONING AND CABIN PRESSURIZATION (ATA 21)
13.11.1. Air supply AG-13-11-01-B2 2
13.11.2. Air conditioning AG-13-11-02-B2 3

13.11.3. Pressurization AG-13-11-03-B2 3
243
13.11.4. Safety and warning devices AG-13-11-03-B2 3
13.12 FIRE PROTECTION (ATA 26)
(a) AG-13-12a-B2 3

System tests.
(b) AG-13-12b-B2 1
13.13 FUEL SYSTEMS (ATA 28) AG-13-13-B2 3
244
System lay-out; 1
Fuel tanks; 1
Supply systems; 1
Dumping, venting and draining; 1
Cross-feed and transfer; 2
Indications and warnings; 3
Refuelling and defuelling; 2
Longitudinal balance fuel systems. 3
13.14 HYDRAULIC POWER (ATA 29) AG-13-14-B2 3
System lay-out; 1
Hydraulic fluids; 1
Hydraulic reservoirs and accumulators; 1
Pressure generation: electric, mechanical, pneumatic; 3
Emergency pressure generation; 3
Filters; 1
Pressure Control; 3
Power distribution; 1
Indication and warning systems; 3
Interface with other systems. 3
13.15 ICE AND RAIN PROTECTION (ATA 30) AG-13-15-B2 3
245
Ice formation, classification and detection; 2

Anti-icing systems: electrical, hot air and chemical; 2
De-icing systems: electrical, hot air, pneumatic and chemical ; 3
Rain repellent; 1
Probe and drain heating; 3
Wiper systems. 1
13.16. LANDING GEAR (ATA 32) AG-13-16-B2 3
Construction, shock absorbing; 1

Extension and retraction systems: normal and emergency; 3
Indications and warning; 3
Wheels, brakes, antiskid and auto braking; 3
Tyres; 1
Steering; 3
Air-ground sensing. 3
13.17. OXYGEN (ATA 35) AG-13-17-B2 3
System lay-out: 3
 cockpit,
 cabin;
Sources, storage, charging and distribution; 3
Supply regulation; 3
Indications and warnings. 3
13.18. PNEUMATIC/VACUUM (ATA 36) AG-13-18-B2 3
246
System lay-out; 2
Sources: engine / APU, compressors, reservoirs, ground supply; 2
Pressure control; 3
Distribution; 1
Indications and warnings; 3
Interfaces with other systems. 3
13.19. WATER/WASTE (ATA 38)
Water system lay-out, supply, distribution, servicing and draining; AG-13-19-B2 2

Corrosion aspects.
Functions that may be typically integrated in the Integrated Modular Avionic (IMA) modules are, among AG-13-20-B2 3
others:
Bleed Management, Air Pressure Control, Air Ventilation and Control, Avionics and Cockpit Ventilation
Control, Temperature Control, Air Traffic Communication, Avionics Communication Router, Electrical
Load Management, Circuit Breaker Monitoring, Electrical System BITE, Fuel Management, Braking
Control, Steering Control, Landing Gear Extension and Retraction, Tyre Pressure Indication, Oleo
Pressure Indication, Brake Temperature Monitoring, etc.
Core System; Network Components.
13.21. CABIN SYSTEMS (ATA 44)
247
The units and components which furnish a means of entertaining the passengers and providing AG-13-21-B2 3
transmissions.
following systems:
Cabin Core System;
13.22. INFORMTION SYSTEMS (ATA 46)
248
The units and components which furnish a means of storing, updating and retrieving digital information AG-13-18-B2 3
Systems
249
Module 14
PROPULSION
250
MODULE 14. PROPULSION – B2 CATEGORY

14.1. TURBINE ENGINES
(a) AG-14-01a-B2 1
Constructional arrangement and operation of turbojet, turbofan, turbo shaft and turbopropeller engines;
(b) AG-14-01b-B2 2
Electronic Engine control and fuel metering systems (FADEC).
14.2. ENGINE INDICATING SYSTEMS
251
Exhaust gas temperature / Interstage turbine temperature systems; AG-14-02-B2 2

Engine speed;
Engine thrust indication: engine pressure ratio, engine turbine discharge pressure or jet pipe pressure
systems;
Oil pressure and temperature;
Fuel pressure, temperature and flow;
Manifold pressure;
Engine torque;
Propeller speed.
14.3. STARTING AND IGNITION SYSTEMS
Operation of engine start systems and components; AG-14-03-B2 2

Ignition systems and components;
Maintenance safety requirements.
252
Module 15
GAS TURBINE ENGINE
253
MODULE 15. GAS TURBINE ENGINE – A1 & A3 CATEGORIES

15.1. FUNDAMENTALS
Potential energy, kinetic energy, Newton's laws of motion, Brayton cycle; AG-15-01-A1-A3 1
The relationship between force, work, power, energy, velocity, acceleration;
Constructional arrangement and operation of turbojet, turbofan, turboshaft, turboprop.
15.2. ENGINE PERFORMANCE
Gross thrust, net thrust, choked nozzle thrust, thrust distribution, resultant thrust, thrust horsepower, - -
equivalent shaft horsepower, specific fuel consumption;
Engine efficiencies;
By-pass ratio and engine pressure ratio;
Pressure, temperature and velocity of the gas flow
Engine ratings, static thrust, influence of speed, altitude and hot climate, flat rating, limitations.
15.3. INLET
Compressor inlet ducts; AG-15-03- A1-A3 -B1 2

Effects of various inlet configurations;
Ice protection.
254
15.4. COMPRESSORS
Axial and centrifugal types; AG-15-04- A1-A3 1

Constructional features and operating principles and applications;
Fan balancing;
Operation;
Causes and effects of compressors tall and surge;
Methods of air flow control: bleed valves, variable inlet guide vanes, variable stator vanes, rotating stator
blades;
Compressor ratio.
15.5. COMBUSTION SECTION
Constructional features and principles of operation. AG-15-05- A1-A3 1
15.6. TURBINE SECTION
Operation and characteristics of different turbine blade types; AG-15-06- A1-A3-B1 2

Blade to disk attachment;
Nozzle guide vanes;
Causes and effects of turbine blade stress and creep.
15.7. EXHAUST
Constructional features and principles of operation; AG-15-07- A1-A3 1

Convergent, divergent and variable area nozzles;
Engine noise reduction;
Thrust reversers.
255
15.8. BEARINGS AND SEALS
Constructional features and principles of operation. - -
15.9. LUBRICANTS AND FUELS
Properties and specifications; AG-15-09- A1-A3 1

Fuel additives;
Safety precautions.
15.10. LUBRICATION SYSTEMS
System operation / lay-out and components. AG-15-10- A1-A3 1
15.11. FUEL SYSTEMS
Operation of engine control and fuel metering systems including electronic engine control (FADEC); AG-15-11- A1-A3 1
Systems lay-out and components.
15.12. AIR SYSTEMS
Operation of engine air distribution and anti-ice control systems, including internal cooling, sealing and AG-15-12- A1-A3 1
external air services.
Operation of engine start systems and components; AG-15-13- A1-A3 1

15.14. ENGINE INDICATION SYSTEMS
256
Exhaust gas temperature/ Interstage turbine temperature; AG-15-14- A1-A3 1

Engine thrust Indication:
 engine pressure ratio,
 engine turbine discharge pressure or jet pipe pressure systems;
Fuel pressure and flow;
Engine speed;
Vibration measurement and indication;
Torque;
Power.
15.15. POWER AUGMENTATION SYSTEMS
Operation and applications; - -

Water injection, water methanol;
Afterburner systems.
15.16. TURBO-PROP ENGINES
Gas coupled / free turbine and gear coupled turbines; AG-15-16- A1-A3 1
Reduction gears;
Integrated engine and propeller controls;
Overspeed safety devices.
15.17. TURBO-SHAFT ENGINES
Arrangements drive systems, reduction gearing, couplings, control systems. AG-15-17- A1-A3 1
257
15.18. AUXILIARY POWER UNITS (APUs)
Purpose, operation, protective systems. AG-15-18- A1-A3 1
15.19. POWERPLANT INSTALLATION
Configuration of firewalls, cowlings, acoustic panels, engine mounts, anti-vibration mounts, hoses, pipes, AG-15-19- A1-A3 1
feeders, connectors, wiring looms, control cables and rods, lifting points and drains.
15.20. FIRE PROTECTION SYSTEMS
Operation of detection and extinguishing systems. AG-15-20- A1-A3 1
15.21. ENGINE MONITORING AND GROUND INSTALLATION
Procedures for starting and ground run-up; AG-15-21- A1-A3 1

Interpretation of engine power output and parameters;
Trend (including oil analysis, vibration and boroscope) monitoring;
Inspection of engine and components to criteria, tolerances and data specified by engine manufacturer;
Compressor washing / cleaning;
Foreign object damage.
15.22. ENGINE STORAGE AND PRESERVATION
Preservation and depreservation for accessories/systems - -
258
MODULE 15. GAS TURBINE ENGINE – B1.1 & B1.3 CATEGORIES

15.1. FUNDAMENTALS
Potential energy, kinetic energy, Newton's laws of motion, Brayton cycle; AG-15-01-B11-B13 2
The relationship between force, work, power, energy, velocity, acceleration;
Constructional arrangement and operation of turbojet, turbofan, turboshaft, turboprop.
Gross thrust, net thrust, choked nozzle thrust, thrust distribution, resultant thrust, thrust horsepower, AG-15-02- B11-B13 2
equivalent shaft horsepower, specific fuel consumption;
Engine efficiencies;
By-pass ratio and engine pressure ratio;
Pressure, temperature and velocity of the gas flow
Engine ratings, static thrust, influence of speed, altitude and hot climate, flat rating, limitations.
15.3. INLET
Compressor inlet ducts; AG-15-03-A- B11-B13 2

Effects of various inlet configurations;
Ice protection.
259
15.4. COMPRESSORS
Axial and centrifugal types; AG-15-04- B11-B13 2

Constructional features and operating principles and applications;
Fan balancing;
Operation;
Causes and effects of compressors tall and surge;
Methods of air flow control: bleed valves, variable inlet guide vanes, variable stator vanes, rotating stator
blades;
Compressor ratio.
15.5. COMBUSTION SECTION
Constructional features and principles of operation. AG-15-05- B11-B13 2
15.6. TURBINE SECTION
Operation and characteristics of different turbine blade types; AG-15-06-A- B11-B13 2

Blade to disk attachment;
Nozzle guide vanes;
Causes and effects of turbine blade stress and creep.
15.7. EXHAUST
Constructional features and principles of operation; AG-15-07- B11-B13 2

Convergent, divergent and variable area nozzles;
Engine noise reduction;
Thrust reversers.
260
15.8. BEARINGS AND SEALS
Constructional features and principles of operation. AG-15-08- B11-B13 2
15.9. LUBRICANTS AND FUELS
Properties and specifications; AG-15-09- B11-B13 2

Fuel additives;
Safety precautions.
System operation / lay-out and components. AG-15-10- B11-B13 2
15.11. FUEL SYSTEMS
Operation of engine control and fuel metering systems including electronic engine control (FADEC); AG-15-11- B11-B13 2
15.12. AIR SYSTEMS
Operation of engine air distribution and anti-ice control systems, including internal cooling, sealing and AG-15-12- B11-B13 2
external air services.
Operation of engine start systems and components; AG-15-13- B11-B13 2

261
Exhaust gas temperature/ Interstage turbine temperature; AG-15-14- B11-B13 2

Engine thrust Indication:
 engine pressure ratio,
 engine turbine discharge pressure or jet pipe pressure systems;
Engine speed;
Vibration measurement and indication;
Torque;
Power.
15.15. POWER AUGMENTATION SYSTEMS
Operation and applications; AG-15-15- B11-B13 2

Water injection, water methanol;
Afterburner systems.
15.16. TURBO-PROP ENGINES
Gas coupled / free turbine and gear coupled turbines; AG-15-16- B11-B13 2
Reduction gears;
Integrated engine and propeller controls;
Overspeed safety devices.
15.17. TURBO-SHAFT ENGINES
Arrangements drive systems, reduction gearing, couplings, control systems. AG-15-17- B11-B13 2
262
15.18. AUXILIARY POWER UNITS (APUs)
Purpose, operation, protective systems. AG-15-18- B11-B13 2
15.19. POWERPLANT INSTALLATION
Configuration of firewalls, cowlings, acoustic panels, engine mounts, anti-vibration mounts, hoses, pipes, AG-15-19- B11-B13 2
15.20. FIRE PROTECTION SYSTEMS
Operation of detection and extinguishing systems. AG-15-20- B11-B13 2
15.21. ENGINE MONITORING AND GROUND INSTALLATION
Procedures for starting and ground run-up; AG-15-21- B11-B13 3

Trend (including oil analysis, vibration and boroscope) monitoring;
Inspection of engine and components to criteria, tolerances and data specified by engine manufacturer;
Compressor washing / cleaning;
Foreign object damage.
Preservation and depreservation for accessories/systems AG-15-22- B11-B13 2
263
Module 16
PISTON ENGINE
264
MODULE 16. PISTON ENGINE – A2 & A4 CATEGORIES

16.1. FUNDAMENTALS
Mechanical, thermal and volumetric efficiencies; AG-16-01-A2-A4 1

Operating principles: 2 stroke, 4 stroke, Otto and Diesel;
Piston displacement and compression ratio;
Engine configuration and firing order.
Power calculation and measurement; AG-16-02- A2-A4 1

Factors affecting engine power;
Mixtures/leaning, pre-ignition.
16.3. ENGINE CONSTRUCTION
265
Crank case, crank shaft, cam shafts, sumps; AG-15-03- A2-A4-B1 1

Accessory gearbox;
Cylinder and piston assemblies;
Connecting rods, inlet and exhaust manifolds;
Valve mechanisms;
Propeller reduction gearboxes.
16.4. ENGINE FUEL SYSTEMS
16.4.1. Carburettors
Types, construction and principles of operation; AG-16-04-01- A2-A4 1

Icing and heating.
16.4.2. Fuel injection systems
Types, construction and principles of operation. AG-16-04-02- A2-A4 1
16.4.3. Electronic engine control
Operation of engine control and fuel metering systems including electronic engine control (FADEC); AG-16-04-03- A2-A4 1
16.5. STARTING AND IGNITION YSTEMS
Starting systems, pre-heat systems; AG-16-05- A2-A4 1

Magneto types, construction and principles of operation;
Ignition harnesses, spark plugs;
Low and high tension systems.
266
16.6. INDUCTION, EXHAUST AND COOLING SYSTEMS
Construction and operation of: induction systems including alternate air systems; AG-16-06- A2-A4 1
Exhaust systems, engine cooling systems — air and liquid.
16.7. SUPERCHARGING/TURBOCHARGING
Principles and purpose of supercharging and its effects on engine parameters; AG-16-07- A2-A4 1
Construction and operation of supercharging/turbocharging systems;
System terminology;
Control systems;
System protection..
16.8. LUBRICNTS AND FUELS
Properties and specifications; AG-16-08- A2-A4 1

Fuel additives;
Safety precautions.
System operation/lay-out and components. AG-16-09- A2-A4 1
267
Engine speed; AG-16-10- A2-A4 1

Cylinder head temperature;
Coolant temperature;
Exhaust Gas Temperature;
Manifold pressure.
16.11. POWERPLANT INSTLLATION
Configuration of firewalls, cowlings, acoustic panels, engine mounts, anti-vibration mounts, hoses, pipes, AG-16-11- A2-A4 1
16.12. ENGINE MONITORING AND GROUND OPERATIONS
Procedures for starting and ground run-up; AG-16-12- A2-A4 1

Inspection of engine and components: criteria, tolerances, and data specified by engine manufacturer.
Preservation and depreservation for the engine and accessories/systems. AG-16-13- A2-A4 -
268
MODULE 16. PISTON ENGINE – B1.2 & B1.4 CATEGORIES

16.1. FUNDAMENTALS
Mechanical, thermal and volumetric efficiencies; AG-16-01-B12-B14 2

Power calculation and measurement; AG-16-02- B12-B14 2

269
Crank case, crank shaft, cam shafts, sumps; AG-15-03-A- B12-B14 2
Accessory gearbox;
Valve mechanisms;
Types, construction and principles of operation; AG-16-04-01- B12-B14 2
Icing and heating.
Types, construction and principles of operation. AG-16-04-02- B12-B14 2
Operation of engine control and fuel metering systems including electronic engine control (FADEC); AG-16-04-03-A- B12-B14 2
Starting systems, pre-heat systems; AG-16-05- B12-B14 2

270
Construction and operation of: induction systems including alternate air systems; AG-16-06- B12-B14 2
Principles and purpose of supercharging and its effects on engine parameters; AG-16-07- B12-B14 2

System terminology;
Control systems;
System protection..
Properties and specifications; AG-16-08- B12-B14 2
Fuel additives;
Safety precautions.
System operation/lay-out and components. AG-16-09- B12-B14 2
271
Engine speed; AG-16-10- B12-B14 2

Manifold pressure.
Configuration of firewalls, cowlings, acoustic panels, engine mounts, anti-vibration mounts, hoses, pipes, AG-16-11- B12-B14 2
Procedures for starting and ground run-up; AG-16-12- B12-B14 3

Preservation and depreservation for the engine and accessories/systems. AG-16-13- B12-B14 2
272
MODULE 16. PISTON ENGINE – B3 CATEGORY

16.1. FUNDAMENTALS
Mechanical, thermal and volumetric efficiencies; AG-16-01-B3 2

Power calculation and measurement; AG-16-02-B3 2

273
Crank case, crank shaft, cam shafts, sumps; AG-15-03-A-B1 2
Accessory gearbox;
Valve mechanisms;
Types, construction and principles of operation; AG-16-04-01-B3 2
Icing and heating.
Types, construction and principles of operation. AG-16-04-02-B3 2
Operation of engine control and fuel metering systems including electronic engine control (FADEC); AG-16-04-03-A-B3 2
Starting systems, pre-heat systems; AG-16-05-B3 2

274
Construction and operation of: induction systems including alternate air systems; AG-16-06-B3 2
Principles and purpose of supercharging and its effects on engine parameters; AG-16-07-B3 2

System terminology;
Control systems;
System protection..
Properties and specifications; AG-16-08-B3 2
Fuel additives;
Safety precautions.
System operation/lay-out and components. AG-16-09-B3 2
275
Engine speed; AG-16-10-B3 2

Manifold pressure.
Configuration of firewalls, cowlings, acoustic panels, engine mounts, anti-vibration mounts, hoses, pipes, AG-16-11-B3 2
Procedures for starting and ground run-up; AG-16-12-B3 2

Preservation and depreservation for the engine and accessories/systems. AG-16-13-B3 1
276
Module 17
PROPELLER
277
MODULE 17A. PROPELLER – A1 CATEGORY

17A.1. FUNDAMENTALS
Blade element theory; AG-17A-01-A 1

High/low blade angle, reverse angle, angle of attack,
rotational speed;
Propeller slip;
Aerodynamic, centrifugal, and thrust forces;
Torque;
Relative airflow on blade angle of attack; vibration and resonance.
17A.2. PROPELLER CONSTRUCTION
Construction methods and materials used in composite and metal propellers; AG-17A-02-A 1
Blade station, blade face, blade shank, blade back and hub assembly;
Fixed pitch, controllable pitch, constant speeding propeller;
Propeller/spinner installation.
17A.3. PROPELLER PITCH CONTROL
278
Speed control and pitch change methods; AG-17A-03-A 1

Feathering and reverse pitch;
Overspeed protection.
17A.4. PROPELLER SYNCHRONIZING
Synchronising and synchrophasing equipment. - -
17A.5. PROPELLER ICE PROTECTION
Fluid and electrical de-icing equipment. AG-17A-05-A 1
17A.6. PROPELLER MAINTENANCE
Static and dynamic balancing; AG-17A-06-A 1

Blade tracking;
Assessment of blade damage, erosion, corrosion, impact damage, delamination;
Propeller treatment/repair schemes;
Propeller engine running.
17A.7. PROPELLER STORAGE ANDPRESERVATION
Propeller preservation and depreservation AG-17A-07-A 1
279
MODULE 17A. PROPELLER – B1 CATEGORY

17A.1. FUNDAMENTALS
Blade element theory; AG-17A-01-B1 2

rotational speed;
Propeller slip;
Torque;
17A.2. PROPELLER CONSTRUCTION
Construction methods and materials used in composite and metal propellers; AG-17A-02-B1 2
17A.3. PROPELLER PITCH CONTROL
280
Speed control and pitch change methods; AG-17A-03-B1 2

17A.4. PROPELLER SYNCHRONIZING
Synchronising and synchrophasing equipment. AG-17A-04-B1 2
17A.5. PROPELLER ICE PROTECTION
Fluid and electrical de-icing equipment. AG-17A-05-B1 2
17A.6. PROPELLER MAINTENANCE
Static and dynamic balancing; AG-17A-06-B1 3

Blade tracking;
17A.7. PROPELLER STORAGE AND PRESERVATION
Propeller preservation and depreservation AG-17A-07-B1 2
281
MODULE 17B. PROPELLER – B3 CATEGORY

17B.1. FUNDAMENTALS
Blade element theory; AG-17B-01-B3 2

rotational speed;
Propeller slip;
Torque;
17B.2. PROPELLER CONSTRUCTION
Construction methods and materials used in composite and metal propellers; AG-17B-02-B3 2
17B.3. PROPELLER PITCH CONTROL
282
Speed control and pitch change methods; AG-17B-03-B3 2

17B.4. PROPELLER SYNCHRONIZING
Synchronising and synchrophasing equipment. AG-17B-04-B3 2
17B.5. PROPELLER ICE PROTECTION
Fluid and electrical de-icing equipment. AG-17B-05-B3 2
17B.6. PROPELLER MAINTENANCE
Static and dynamic balancing; AG-17B-06-B3 2

Blade tracking;
17B.7. PROPELLER STORAGE AND PRESERVATION
Propeller preservation and depreservation AG-17B-07-B3 2
283

New Syllabuses

Uploaded by

Copyright:

Available Formats

New Syllabuses

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

New Syllabuses

Uploaded by

Copyright:

Available Formats

AeroGATES: PART-66 syllabuses

PART-66 Syllabuses Cross-reference Level

MODULE 1. MATHEMATICS – A CATEGORY

Arithmetical terms and signs, AG-01-01-A 1

Linear equations and their solutions,

Simple geometrical constructions.

Graphical representation; nature and uses of graphs,

PART-66 Syllabuses Cross-reference Level

MODULE 1. MATHEMATICS – B1, B2 & B3 CATEGORIES

Arithmetical terms and signs, AG-01-01-B1-B2-B3 2

Linear equations and their solutions,

Simple geometrical constructions.

Graphical representation; nature and uses of graphs,

PART-66 Syllabuses Cross-reference Level

MODULE 2. PHYSICS – A CATEGORY

Nature of matter: the chemical elements, structure of atoms, molecules; AG-02-01-A-B1-B2-B3 1

2.2.1. Statics AG-02-02-01-A-B2-B3 1

Forces, moments and couples, representation as vectors;

2.2.2. Kinetics AG-02-02-02-A-B2-B3 1

2.2.3. Dynamics AG-02-02-02-A-B2-B3 1

(a) Mass AG-02-02-03a-A-B2-B3 1

(b) Momentum, conservation of momentum AG-02-02-03b-A-B3 1

Momentum, conservation of momentum;

2.2.4. Fluid dynamics

Specific gravity and density

Viscosity, fluid resistance, effects of streamlining;

Heat capacity, specific heat;

2.4. OPTICS (LIGHT)

Nature of light; speed of light; - -

2.5. WAVE MOTION AND SOUND

Wave motion: mechanical waves, sinusoidal wave motion, - -

PART-66 Syllabuses Cross-reference Level

MODULE 2. PHYSICS – B1 CATEGORY

Nature of matter: the chemical elements, structure of atoms, molecules; AG-02-01-A-B1-B2-B3 1

2.2.1. Statics AG-02-02-01-B1 2

Forces, moments and couples, representation as vectors;

2.2.2. Kinetics AG-02-02-02-B1 2

(a) Mass AG-02-02-03a-B1 2

(b) Momentum, conservation of momentum AG-02-02-03b-B1-B2 2

Momentum, conservation of momentum;

2.2.4. Fluid dynamics

Specific gravity and density

Viscosity, fluid resistance, effects of streamlining;

Heat capacity, specific heat;

2.4. OPTICS (LIGHT)

Nature of light; speed of light; AG-02-04-B1-B2 2

2.5. WAVE MOTION AND SOUND

Wave motion: mechanical waves, sinusoidal wave motion, AG-02-05-B1-B2 2

PART-66 Syllabuses Cross-reference Level

MODULE 2. PHYSICS – B2 CATEGORY

Nature of matter: the chemical elements, structure of atoms, molecules; AG-02-01-A-B1-B2-B3 1

2.2.1. Statics AG-02-02-01-A-B2-B3 1

Forces, moments and couples, representation as vectors;

2.2.2. Kinetics AG-02-02-02-A-B2-B3 1

(a) Mass AG-02-02-03a-A-B2-B3 1

(b) Momentum, conservation of momentum AG-02-02-03b-B1-B2 2

Momentum, conservation of momentum;

2.2.4. Fluid dynamics

Specific gravity and density