H61M-S1 PLUS

User Manual

Version 1.0
Published January 2014
Copyright©2014 ASRock INC. All rights reserved.

1
Copyright Notice:
No part of this manual may be reproduced, transcribed, transmitted, or translated in any lan-
guage, in any form or by any means, except duplication of documentation by the purchaser for
backup purpose, without written consent of ASRock Inc.
Products and corporate names appearing in this manual may or may not be registered trade-
marks or copyrights of their respective companies, and are used only for identification or expla-
nation and to the owners’ benefit, without intent to infringe.

Disclaimer:
Specifications and information contained in this manual are furnished for informational use
only and subject to change without notice, and should not be constructed as a commitment by
ASRock. ASRock assumes no responsibility for any errors or omissions that may appear in this
manual.
With respect to the contents of this manual, ASRock does not provide warranty of any kind,
either expressed or implied, including but not limited to the implied warranties or conditions of
merchantability or fitness for a particular purpose.
In no event shall ASRock, its directors, officers, employees, or agents be liable for any indirect,
special, incidental, or consequential damages (including damages for loss of profits, loss of
business, loss of data, interruption of business and the like), even if ASRock has been advised
of the possibility of such damages arising from any defect or error in the manual or product.

The terms HDMITM and HDMI High-Definition Multimedia Interface, and the HDMI logo are trade-
marks or registered trademarks of HDMI Licensing LLC in the United States and other countries.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause
undesired operation.

CALIFORNIA, USA ONLY

The Lithium battery adopted on this motherboard contains Perchlorate, a toxic substance con-
trolled in Perchlorate Best Management Practices (BMP) regulations passed by the California
Legislature. When you discard the Lithium battery in California, USA, please follow the related
regulations in advance.
“Perchlorate Material-special handling may apply, see
www.dtsc.ca.gov/hazardouswaste/perchlorate”

ASRock Website: http://www.asrock.com

2
 Contents
1 Introduction......................................................... 5
1.1 Package Contents.......................................................... 5
1.2 Specifications.................................................................. 6
1.3 Unique Features............................................................. 9
1.4 Motherboard Layout ...................................................... 13
1.5 I/O Panel . ...................................................................... 14
2 Installation........................................................... 16
2.1 Screw Holes.................................................................... 16
2.2 Pre-installation Precautions .......................................... 16
2.3 CPU Installation.............................................................. 17
2.4 Installation of Heatsink and CPU fan.............................. 19
2.5 Installation of Memory Modules (DIMM)......................... 20
2.6 Expansion Slots (PCI Express Slots)................................. 21
2.7 Jumpers Setup .......................................................... 22
2.8 Onboard Headers and Connectors . ........................... 23
2.9 Driver Installation Guide ............................................. 28
3 UEFI SETUP UTILITY........................................... 29
3.1 Introduction..................................................................... 29
3.1.1 UEFI Menu Bar..................................................... 29
3.1.2 Navigation Keys.................................................... 30
3.2 Main Screen.................................................................... 30
3.3 OC Tweaker Screen....................................................... 31
3.4 Advanced Screen............................................................ 35
3.4.1 CPU Configuration................................................ 36
3.4.2 North Bridge Configuration................................... 38
3.4.3 South Bridge Configuration................................... 39
3.4.4 Storage Configuration........................................... 40
3.4.5 Intel(R) Rapid Start Technology............................ 41
3.4.6 Intel(R) Smart Connect Technology...................... 42
3.4.7 Super IO Configuration......................................... 43
3.4.8 ACPI Configuration............................................... 44
3.4.9 USB Configuration................................................ 45
3.5 Tool................................................................................. 46
3.6 Hardware Health Event Monitoring Screen.................... 48
3.7 Boot Screen.................................................................... 49
3.8 Security Screen.............................................................. 51
3.9 Exit Screen..................................................................... 52

3
4 Software Support................................................ 53
4.1 Install Operating System................................................. 53
4.2 Support CD Information.................................................. 53
4.2.1 Running Support CD............................................. 53
4.2.2 Drivers Menu......................................................... 53
4.2.3 Utilities Menu........................................................ 53
4.2.4 Contact Information............................................... 53

4
 Chapter 1: Introduction
Thank you for purchasing ASRock H61M-S1 PLUS motherboard, a reliable moth-
erboard produced under ASRock’s consistently stringent quality control. It delivers
excellent performance with robust design conforming to ASRock’s commitment to
quality and endurance.
In this manual, chapter 1 and 2 contain introduction of the motherboard and step-
by-step guide to the hardware installation. Chapter 3 and 4 contain the configuration
guide to BIOS setup and information of the Support CD.

Because the motherboard specifications and the BIOS software might be

updated, the content of this manual will be subject to change without no-
tice. In case any modifications of this manual occur, the updated version
will be available on ASRock website without further notice. You may find
the latest VGA cards and CPU support lists on ASRock website as well.
ASRock website http://www.asrock.com
If you require technical support related to this motherboard, please visit
our website for specific information about the model you are using.
www.asrock.com/support/index.asp

1.1 Package Contents

ASRock H61M-S1 PLUS Motherboard (Micro ATX Form Factor)
ASRock H61M-S1 PLUS Quick Installation Guide
ASRock H61M-S1 PLUS Support CD
2 x Serial ATA (SATA) Data Cables (Optional)
1 x Mouse Pad
1 x I/O Panel Shield

ASRock Reminds You...

To get better performance in Windows® 8.1 / 8.1 64-bit / 8 / 8 64-bit / 7 / 7
64-bit / VistaTM / VistaTM 64-bit, it is recommended to set the BIOS option
in Storage Configuration to AHCI mode.

5
1.2 Specifications

Platform - Micro ATX Form Factor

- All Solid Capacitor design
CPU - Supports 3rd and 2nd Generation Intel® CoreTM i7 / i5 / i3 /
Xeon® / Pentium® / Celeron® in LGA1155 Package
- Supports Intel® Turbo Boost 2.0 Technology
- Supports K-Series unlocked CPU
Chipset - Intel® H61
- Supports Intel® Rapid Start Technology and Smart Connect
Technology
Memory - Dual Channel DDR3 Memory Technology
- 2 x DDR3 DIMM slots
- Supports DDR3 1600/1333/1066 non-ECC, un-buffered
memory (DDR3 1600 with Intel® Ivy Bridge CPU, DDR3
1333 with Intel® Sandy Bridge CPU)
- Max. capacity of system memory: 16GB (see CAUTION 1)
- Supports Intel® Extreme Memory Profile (XMP) 1.3 / 1.2 with
Intel® Ivy Bridge CPU
Expansion Slot - 1 x PCI Express 3.0 x16 slot (blue @ x16 mode)
* PCIE 3.0 is only supported with Intel® Ivy Bridge CPU. With
Intel® Sandy Bridge CPU, it only supports PCIE 2.0.
- 1 x PCI Express 2.0 x1 slot
Graphics * Intel® HD Graphics Built-in Visuals and the VGA outputs can
be supported only with processors which are GPU
integrated.
- Supports Intel® HD Graphics Built-in Visuals: Intel® Quick
Sync Video 2.0, Intel® InTruTM 3D, Intel® Clear Video HD
Technology, Intel® InsiderTM, Intel® HD Graphics 2500/4000
with Intel® Ivy Bridge CPU
- Supports Intel® HD Graphics Built-in Visuals: Intel® Quick
Sync Video, Intel® InTruTM 3D, Intel® Clear Video HD
Technology, Intel® HD Graphics 2000/3000, Intel® Advanced
Vector Extensions (AVX) with Intel® Sandy Bridge CPU
- Pixel Shader 5.0, DirectX 11 with Intel® Ivy Bridge CPU.
Pixel Shader 4.1, DirectX 10.1 with Intel® Sandy Bridge
CPU.
- Max. shared memory 1760MB with Intel® Ivy Bridge CPU.
Max. shared memory 1759MB with Intel® Sandy Bridge
CPU.

6
 - Dual Graphics Output: support HDMI and D-Sub ports by
independent display controllers
- Supports HDMI Technology with max. resolution up to
1920x1200 @ 60Hz
- Supports D-Sub with max. resolution up to 2048x1536 @
75Hz
- Supports Auto Lip Sync, Deep Color (12bpc), xvYCC and
HBR (High Bit Rate Audio) with HDMI (Compliant HDMI
monitor is required)
- Supports HDCP function with HDMI port
- Supports Full HD 1080p Blu-ray (BD) playback with HDMI
port
Audio - 5.1 CH HD Audio (Realtek ALC662 Audio Codec)
LAN - PCIE x1 Gigabit LAN 10/100/1000 Mb/s
- Realtek RTL8111E
- Supports Wake-On-LAN
- Supports LAN Cable Detection
- Supports Energy Efficient Ethernet 802.3az
- Supports PXE
Rear Panel I/O I/O Panel
- 1 x PS/2 Mouse Port
- 1 x PS/2 Keyboard Port
- 1 x Serial Port: COM1
- 1 x Parallel Port (ECP/EPP support)
- 1 x D-Sub Port
- 1 x HDMI Port
- 4 x USB 2.0 Ports
- 1 x RJ-45 LAN Port with LED (ACT/LINK LED and SPEED
LED)
- HD Audio Jack: Line in/Front Speaker/Microphone
Storage - 4 x SATA2 3.0 Gb/s connectors, support NCQ, AHCI and
Hot Plug functions
Connector - 1 x IR header
- 1 x Power LED header
- 1 x Chassis Intrusion header
- 1 x LPC/TPM header
- 1 x CPU Fan connectors (4-pin)
- 1 x Chassis Fan connector (4-pin)
- 1 x 24 pin ATX power connector
- 1 x 4 pin 12V power connector
- 1 x Front panel audio connector

7
 - 1 x SPDIF Out connector
- 2 x USB 2.0 headers (support 4 USB 2.0 ports)
BIOS Feature - 32Mb AMI UEFI Legal BIOS with GUI support
- Supports “Plug and Play”
- ACPI 1.1 Compliance Wake Up Events
- Supports jumperfree
- SMBIOS 2.3.1 Support
Support CD - Drivers, Utilities, AntiVirus Software (Trial Version), Google
Chrome Browser and Toolbar, Start8 (30 days trial)
Hardware - CPU/Chassis Temperature Sensing
Monitor - CPU/Chassis Fan Tachometer
- CPU Quiet Fan (Allow Chassis Fan Speed Auto-Adjust by
CPU Temperature)
- CPU/Chassis Fan Multi-Speed Control
- CASE OPEN detection
- Voltage Monitoring: +12V, +5V, +3.3V, CPU Vcore
OS - Microsoft® Windows® 8.1 32-bit / 8.1 64-bit / 8 32-bit / 8
64-bit / 7 32-bit / 7 64-bit / VistaTM 32-bit / VistaTM 64-bit / XP
32-bit / XP 64-bit (Windows® 8.1 is supported with Intel® Ivy
Bridge CPU for onboard VGA.)
Certifications - FCC, CE, WHQL
* For detailed product information, please visit our website: http://www.asrock.com

WARNING
Please realize that there is a certain risk involved with overclocking,
including adjusting the setting in the BIOS, applying Untied Overclocking
Technology, or using third-party overclocking tools. Overclocking may
affect your system’s stability, or even cause damage to the components
and devices of your system. It should be done at your own risk and
expense. We are not responsible for possible damage caused by
overclocking.

CAUTION!
1. Due to the operating system limitation, the actual memory size
may be less than 4GB for the reservation for system usage un-
der Windows® 8.1 / 8 / 7 / VistaTM / XP. For Windows® OS with
64-bit CPU, there is no such limitation. You can use ASRock
XFast RAM to utilize the memory that Windows® cannot use.

8
1.3 Unique Features

ASRock Extreme Tuning Utility (AXTU)

ASRock Extreme Tuning Utility (AXTU) is an all-in-one tool to
ne-tune different system functions in a user-friendly interface,
which includes Hardware Monitor, Fan Control and XFast RAM.
In Hardware Monitor, it shows the major readings of your sys-
tem. In Fan Control, it shows the fan speed and temperature for
you to adjust. In XFast RAM, it fully utilizes the memory space
that cannot be used under Windows® OS 32-bit CPU.

ASRock Instant Boot

ASRock Instant Boot allows you to turn on your PC in just a few
seconds, provides a much more efficient way to save energy,
time, money, and improves system running speed for your sys-
tem. It leverages the S3 and S4 ACPI features which normally
enable the Sleep/Standby and Hibernation modes in Windows®
to shorten boot up time. By calling S3 and S4 at specific timing
during the shutdown and startup process, Instant Boot allows
you to enter your Windows® desktop in a few seconds.

ASRock Instant Flash

ASRock Instant Flash is a BIOS flash utility embedded in Flash
ROM. This convenient BIOS update tool allows you to update
system BIOS without entering operating systems first like MS-
DOS or Windows®. With this utility, you can press the <F6> key
during the POST or the <F2> key to enter into the BIOS setup
menu to access ASRock Instant Flash. Just launch this tool and
save the new BIOS file to your USB flash drive, floppy disk or
hard drive, then you can update your BIOS only in a few clicks
without preparing an additional floppy diskette or other compli-
cated flash utility. Please be noted that the USB flash drive or
hard drive must use FAT32/16/12 file system.

9
ASRock APP Charger
If you desire a faster, less restricted way of charging your
Apple devices, such as iPhone/iPad/iPod Touch, ASRock has
prepared a wonderful solution for you - ASRock APP Charger.
Simply install the APP Charger driver, it makes your iPhone
charge much quickly from your computer and up to 40% faster
than before. ASRock APP Charger allows you to quickly charge
many Apple devices simultaneously and even supports continu-
ous charging when your PC enters into Standby mode (S1),
Suspend to RAM (S3), hibernation mode (S4) or power off (S5).
With APP Charger driver installed, you can easily enjoy the mar-
velous charging experience.

ASRock XFast LAN

ASRock XFast LAN provides a faster internet access, which
includes the benefits listed below. LAN Application Prioritiza-
tion: You can configure your application’s priority ideally and/or
add new programs. Lower Latency in Game: After setting online
game’s priority higher, it can lower the latency in games. Traffic
Shaping: You can watch Youtube HD videos and download si-
multaneously. Real-Time Analysis of Your Data: With the status
window, you can easily recognize which data streams you are
transferring currently.

ASRock XFast RAM

ASRock XFast RAM is a new function that is included into AS-
Rock Extreme Tuning Utility (AXTU). It fully utilizes the memory
space that cannot be used under Windows® OS 32-bit CPU.
ASRock XFast RAM shortens the loading time of previously
visited websites, making web surfing faster than ever. And it
also boosts the speed of Adobe Photoshop 5 times faster. An-
other advantage of ASRock XFast RAM is that it reduces the
frequency of accessing your SSDs or HDDs in order to extend
their lifespan.

10
ASRock Crashless BIOS
ASRock Crashless BIOS allows users to update their BIOS
without fear of failing. If power loss occurs during the BIOS up-
date process, ASRock Crashless BIOS will automatically finish
the BIOS update procedure after regaining power. Please note
that BIOS files need to be placed in the root directory of your
USB disk. Only USB2.0 ports support this feature.

ASRock OMG (Online Management Guard)

Administrators are able to establish an internet curfew or restrict
internet access at specified times via OMG. You may schedule
the starting and ending hours of internet access granted to other
users. In order to prevent users from bypassing OMG, guest
accounts without permission to modify the system time are re-
quired.

ASRock Internet Flash

ASRock Internet Flash searches for available UEFI firmware
updates from our servers. In other words, the system can auto-
detect the latest UEFI from our servers and flash them without
entering Windows® OS.

ASRock Dehumidifier Function

Users may prevent motherboard damages due to dampness by
enabling “Dehumidifier Function”. When enabling Dehumidifier
Function, the computer will power on automatically to dehumidi-
fy the system after entering S4/S5 state.

ASRock Fast Boot

With ASRock’s exclusive Fast Boot technology, it takes less
than 1.5 seconds to logon to Windows® 8.1 / 8 from a cold boot.
No more waiting! The speedy boot will completely change your
user experience and behavior.

11
ASRock Restart to UEFI
Windows® 8.1 / 8 brings the ultimate boot up experience. The
lightning boot up speed makes it hard to access the UEFI setup.
ASRock Restart to UEFI technology is designed for those re-
quiring frequent UEFI access. It allows users to easily enter
the UEFI automatically when turning on the PC next time. Just
simply enable this function; the PC will be assured to access the
UEFI directly in the very beginning.

ASRock Combo Cooler Option (C.C.O.)

Combo Cooler Option (C.C.O.) provides the flexible option to
adopt three different CPU cooler types, Socket LGA 775, LGA
1155 and LGA 1156. Please be noticed that not all the 775 and
1156 CPU Fan can be used.

ASRock Good Night LED

ASRock Good Night LED technology can offer you a better en-
vironment by extinguishing the unessential LED. By enabling
Good Night LED in BIOS, the Power / HDD / LAN LED will be
switched off when system is on. Not only this, Good night LED
will automatically switch off Power and Keyboard LED when the
system enters into Standby / Hibernation mode as well.

12
1.4 Motherboard Layout

Keyboard 1 2 3

Mouse
PS2

PS2

CPU_FAN1

ATX12V1

RoHS
COM1

PARALLEL PORT

DDR3_B1 (64 bit, 240-pin module)

DDR3_A1 (64 bit, 240-pin module)
VGA1

USB 2.0

ATXPWR1
T: USB0
B: USB1

4
HDMI1

USB 2.0
T: USB2 Top:
B: USB3 RJ-45
X Fast LAN
LAN
5
MIC IN
Bottom:

LINE IN
Top:

X Fast RAM
FRONT
Center:

H61M-S1 PLUS CHA_FAN1

PCIE1

Super CMOS
BATTERY
Intel
I/O
AUDIO
CODEC H61
32Mb
BIOS
PCIE2
SATA_3 SATA_1
PLED1

19 1 SPDIF_OUT1 1 CI1 1 6
HD_AUDIO1 IR1 USB4_5 USB6_7 PLED PWRBTN
LPC/TPM1
CLRCMOS1
1 1 1 1 1 1 1
HDLED RESET
7
PANEL1 SATA_2 SATA_0

18 17 16 15 14 13 12 11 10 9 8

1 ATX 12V Power Connector (ATX12V1) 10 Power LED Header (PLED1)

2 CPU Fan Connector (CPU_FAN1) 11 System Panel Header (PANEL1)
3 2 x 240-pin DDR3 DIMM Slots 12 USB 2.0 Header (USB6_7)
(Dual Channel: DDR3_A1, DDR3_B1) 13 USB 2.0 Header (USB4_5)
4 ATX Power Connector (ATXPWR1) 14 Clear CMOS Jumper (CLRCMOS1)
5 Chassis Fan Connector (CHA_FAN1) 15 Chassis Intrusion Header (CI1)
6 SATA2 Connector (SATA_1) 16 LPC / TPM Header (LPC/TPM1)
7 SATA2 Connector (SATA_0) 17 Infrared Module Header (IR1)
8 SATA2 Connector (SATA_3) 18 Front Panel Audio Header (HD_AUDIO1)
9 SATA2 Connector (SATA_2) 19 SPDIF Out Connector (SPDIF_OUT1)

13
1.5 I/O Panel

1 2 3

12 11 10 9 8 7

1 PS/2 Mouse Port (Green) 7 USB 2.0 Ports (USB23)

2 Parallel Port (LPT1) 8 HDMI Port (HDMI1)
3 LAN RJ-45 Port* 9 USB 2.0 Ports (USB01)
4 Line In (Light Blue) 10 D-Sub Port (VGA1)
5 Front Speaker (Lime) 11 Serial Port (COM1)
6 Microphone (Pink) 12 PS/2 Keyboard Port (Purple)

* There are two LED next to the LAN port. Please refer to the table below for the LAN port LED
indications.
LAN Port LED Indications
ACT/LINK SPEED
Activity/Link LED SPEED LED
LED LED
Status Description Status Description
Off No Link Off 10Mbps connection
Blinking Data Activity Orange 100Mbps connection
On Link Green 1Gbps connection
LAN Port

14
To enable Multi-Streaming function, you need to connect a front panel audio cable to the front
panel audio header. Please refer to below steps for the software setting of Multi-Streaming.
For Windows® XP:
After restarting your computer, you will find “Mixer” tool on your system. Please select “Mixer
ToolBox” , click “Enable playback multi-streaming”, and click “ok”. Choose “2CH” or

“4CH” and then you are allowed to select “Realtek HDA Primary output” to use Rear Speaker
and Front Speaker, or select “Realtek HDA Audio 2nd output” to use front panel audio. Then
reboot your system.
For Windows® 8.1 / 8 / 7 / VistaTM:
After restarting your computer, please double-click “Realtek HD Audio Manager” on the
system tray. Set “Speaker Configuration” to “Quadraphonic” or “Stereo”. Click “Device
advanced settings”, choose “Make front and rear output devices playbacks two different audio
streams simultaneously”, and click “ok”. Then reboot your system.

15
 Chapter 2: Installation
This is a Micro ATX form factor motherboard. Before you install the motherboard,
study the configuration of your chassis to ensure that the motherboard fits into it.

Make sure to unplug the power cord before installing or removing the
motherboard. Failure to do so may cause physical injuries to you and
damages to motherboard components.

2.1 Screw Holes

Place screws into the holes indicated by circles to secure the motherboard to the
chassis.

Do not over-tighten the screws! Doing so may damage the motherboard.

2.2 Pre-installation Precautions

Take note of the following precautions before you install motherboard components
or change any motherboard settings.

1. Unplug the power cord from the wall socket before touching any component.
2. To avoid damaging the motherboard components due to static electricity,
NEVER place your motherboard directly on the carpet or the like. Also
remember to use a grounded wrist strap or touch a safety grounded object
before you handle components.
3. Hold components by the edges and do not touch the ICs.
4. Whenever you uninstall any component, place it on a grounded antistatic pad or
in the bag that comes with the component.

Before you install or remove any component, ensure that the power is
switched off or the power cord is detached from the power supply.
Failure to do so may cause severe damage to the motherboard, peripherals,
and/or components.

16
2.3 CPU Installation
For the installation of Intel 1155-Pin CPU,
please follow the steps below. Load Plate

Load Lever

Socket Body
Contact Array

1155-Pin Socket Overview

Before you insert the 1155-Pin CPU into the socket, please check if the
CPU surface is unclean or if there is any bent pin on the socket. Do not
force to insert the CPU into the socket if above situation is found. Other-
wise, the CPU will be seriously damaged.

Step 1. Open the socket:

Step 1-1. Disengaging the lever by depressing
down and out on the hook to clear
retention tab.

Step 1-2. Rotate the load lever to fully open po-

sition at approximately 135 degrees.
Step 1-3. Rotate the load plate to fully open po-
sition at approximately 100 degrees.

Step 2. Remove PnP Cap:

Step 2-1. Attach your index finger to the upper
edge of the PnP Cap.
B
Step 2-2. Use your thumb to remove PnP Cap A

(Pick and Place Cap) from the CPU

socket by lifting the cap tab.

1. It is recommended to use the cap tab to handle and avoid kicking

off the PnP cap.
2. This cap must be placed if returning the motherboard for after
service.

17
Step 3. Insert the 1155-Pin CPU:
Step 3-1. Hold the CPU by the edge where is
marked with black line.

black line
Step 3-2. Orient the CPU with IHS (Integrated
Heat Sink) up. Locate Pin1 and the
two orientation key notches.
orientation key notch alignment key

Pin1

Pin1

alignment key

orientation key notch 1155-Pin Socket

1155-Pin CPU

For proper inserting, please ensure to match the two orientation key
notches of the CPU with the two alignment keys of the socket.

Step 3-3. Carefully place the CPU into the

socket by using a purely vertical mo-
tion.
Step 3-4. Verify that the CPU is within the sock-
et and properly mated to the orient
keys.

Step 4. Close the socket:

Step 4-1. Rotate the load plate onto the IHS.
Step 4-2. While pressing down lightly on load
plate, engage the load lever.
Step 4-3. Secure load lever with load plate tab
under retention tab of load lever.

Please be noticed that this motherboard supports Combo Cooler

Option (C.C.O.), which provides the flexible option to adopt three dif-
ferent CPU cooler types, Socket LGA 775, LGA 1155 and LGA 1156.
The white throughholes are for Socket LGA
1155/1156 CPU fan.

18
2.4 Installation of CPU Fan and Heatsink
This motherboard is equipped with 1155-Pin socket that supports Intel 1155-Pin
CPU. Please adopt the type of heatsink and cooling fan compliant with Intel 1155-
Pin CPU to dissipate heat. Before you installed the heatsink, you need to spray
thermal interface material between the CPU and the heatsink to improve heat dis-
sipation. Ensure that the CPU and the heatsink are securely fastened and in good
contact with each other. Then connect the CPU fan to the CPU_FAN connector
(CPU_FAN1, see page 13, No. 2).
For proper installation, please kindly refer to the instruction manuals of your
CPU fan and heatsink.

Below is an example to illustrate the installation of the heatsink for 1155-Pin CPU.
Step 1. Apply thermal interface material onto center of
IHS on the socket surface.
Apply Thermal
Interface Material

Step 2. Place the heatsink onto the socket. Ensure

Fan cables on side

fan cables are oriented on side closest to the closest to MB header

CPU fan connector on the motherboard (CPU_

FAN1, see page 13, No. 2).
Fastener slots
pointing straight out

Step 3. Align fasteners with the motherboard through-

holes.
Step 4. Rotate the fastener clockwise, then press
down on fastener caps with thumb to install Press Down
(4 Places)
and lock. Repeat with remaining fasteners.

If you press down the fasteners without rotating them clockwise, the
heatsink cannot be secured on the motherboard.

Step 5. Connect fan header with the CPU fan connector on the motherboard.
Step 6. Secure excess cable with tie-wrap to ensure cable does not interfere with
fan operation or contact other components.

19
2.5 Installation of Memory Modules (DIMM)
This motherboard provides two 240-pin DDR3 (Double Data Rate 3) DIMM slots,
and supports Dual Channel Memory Technology. For dual channel configuration,
you always need to install two identical (the same brand, speed, size and chip-
type) memory modules in the DDR3 DIMM slots to activate Dual Channel Memory
Technology. Otherwise, it will operate at single channel mode.

1. It is not allowed to install a DDR or DDR2 memory module into

DDR3 slot;otherwise, this motherboard and DIMM may be
damaged.
2. If you install only one memory module or two non-identical
memory modules, it is unable to activate the Dual Channel
Memory Technology.
3. Some DDR3 1GB double-sided DIMMs with 16 chips may not
work on this motherboard. It is not recommended to install them
on this motherboard.

Installing a DIMM

Please make sure to disconnect power supply before adding or

removing DIMMs or the system components.

Step 1. Unlock a DIMM slot by pressing the retaining clips outward.

Step 2. Align a DIMM on the slot such that the notch on the DIMM matches the
break on the slot.

notch
break

notch
break

The DIMM only fits in one correct orientation. It will cause permanent
damage to the motherboard and the DIMM if you force the DIMM into
the slot at incorrect orientation.

Step 3. Firmly insert the DIMM into the slot until the retaining clips at both ends
fully snap back in place and the DIMM is properly seated.

20
2.6 Expansion Slots (PCI Express Slots)
There are 2 PCI Express slots on this motherboard.
PCIE slots:
PCIE1 (PCIE 3.0 x16 slot) is used for PCI Express x16 lane width
graphics cards.
PCIE2 (PCIE 2.0 x1 slot) is used for PCI Express x1 lane width cards.

Only PCIE1 slot supports Gen 3 speed. To run the PCI Express in Gen
3 speed, please install an Ivy Bridge CPU. If you install a Sandy Bridge
CPU, the PCI Express will run only at PCI Express Gen 2 speed.

Installing an expansion card

Step 1. Before installing the expansion card, please make sure that the power
supply is switched off or the power cord is unplugged. Please read the
documentation of the expansion card and make necessary hardware
settings for the card before you start the installation.
Step 2. Remove the system unit cover (if your motherboard is already installed
in a chassis).
Step 3. Remove the bracket facing the slot that you intend to use. Keep the
screws for later use.
Step 4. Align the card connector with the slot and press firmly until the card is
completely seated on the slot.
Step 5. Fasten the card to the chassis with screws.
Step 6. Replace the system cover.

21
2.7 Jumpers Setup
The illustration shows how jumpers are
setup. When the jumper cap is placed on
pins, the jumper is “Short”. If no jumper cap
is placed on pins, the jumper is “Open”. The
illustration shows a 3-pin jumper whose
pin1 and pin2 are “Short” when jumper cap
is placed on these 2 pins.

Jumper Setting Description

Clear CMOS Jumper
(CLRCMOS1)
(see p.13, No. 14)
Default Clear CMOS

Note: CLRCMOS1 allows you to clear the data in CMOS. To clear and reset the
system parameters to default setup, please turn off the computer and unplug
the power cord from the power supply. After waiting for 15 seconds, use a
jumper cap to short pin2 and pin3 on CLRCMOS1 for 5 seconds. However,
please do not clear the CMOS right after you update the BIOS. If you need
to clear the CMOS when you just finish updating the BIOS, you must boot up
the system first, and then shut it down before you do the clear-CMOS action.
Please be noted that the password, date, time and user default profile will be
cleared only if the CMOS battery is removed.

If you clear the CMOS, the case open may be detected. Please adjust
the BIOS option “Clear Status” to clear the record of previous chassis
intrusion status.

22
2.8 Onboard Headers and Connectors

Onboard headers and connectors are NOT jumpers. Do NOT place

jumper caps over these headers and connectors. Placing jumper caps
over the headers and connectors will cause permanent damage of the
motherboard!

Serial ATA2 Connectors These four Serial ATA2

(SATA_0: see p.13, No. 7) SATA_3 SATA_1 (SATA2) connectors support
(SATA_1: see p.13, No. 6) SATA data cables for internal
(SATA_2: see p.13, No. 9) storage devices. The current
(SATA_3: see p.13, No. 8) SATA_2 SATA_1 SATA2 interface allows up to
3.0 Gb/s data transfer rate.

Serial ATA (SATA) Either end of the SATA data

Data Cable cable can be connected to the
(Optional) SATA / SATA2 hard disk or the
SATA2 connector on this
motherboard.

USB 2.0 Headers Besides four default USB 2.0

(9-pin USB4_5) ports on the I/O panel, there
(see p.13 No. 13) are two USB 2.0 headers on
this motherboard. Each
USB 2.0 header can support
two USB 2.0 ports.
(9-pin USB6_7)
(see p.13 No. 12)

Infrared Module Header This header supports an

(5-pin IR1) optional wireless transmitting
(see p.13 No. 17) and receiving infrared module.

23
Front Panel Audio Header GND This is an interface for front
PRESENCE#
(9-pin HD_AUDIO1) MIC_RET
panel audio cable that allows
OUT_RET
(see p.13 No. 18) convenient connection and
1 control of audio devices.
OUT2_L
J_SENSE
OUT2_R
MIC2_R
MIC2_L

1. High Definition Audio supports Jack Sensing, but the panel wire on
the chassis must support HDA to function correctly. Please follow the
instruction in our manual and chassis manual to install your system.
2. If you use AC’97 audio panel, please install it to the front panel audio
header as below:
A. Connect Mic_IN (MIC) to MIC2_L.
B. Connect Audio_R (RIN) to OUT2_R and Audio_L (LIN) to OUT2_L.
C. Connect Ground (GND) to Ground (GND).
D. MIC_RET and OUT_RET are for HD audio panel only. You don’t
need to connect them for AC’97 audio panel.
E. To activate the front mic.
For Windows® XP / XP 64-bit OS:
Select “Mixer”. Select “Recorder”. Then click “FrontMic”.
For Windows® 8.1 / 8.1 64-bit / 8 / 8 64-bit / 7 / 7 64-bit / VistaTM /
VistaTM 64-bit OS:
Go to the "FrontMic" Tab in the Realtek Control panel. Adjust
“Recording Volume”.

System Panel Header This header accommodates

(9-pin PANEL1) several system front panel
(see p.13 No. 11) functions.

Connect the power switch, reset switch and system status indicator on the
chassis to this header according to the pin assignments below. Note the
positive and negative pins before connecting the cables.

PWRBTN (Power Switch):

Connect to the power switch on the chassis front panel. You may configure
the way to turn off your system using the power switch.
RESET (Reset Switch):
Connect to the reset switch on the chassis front panel. Press the reset
switch to restart the computer if the computer freezes and fails to perform a
normal restart.
PLED (System Power LED):
Connect to the power status indicator on the chassis front panel. The LED

24
 is on when the system is operating. The LED keeps blinking when the sys-
tem is in S1 sleep state. The LED is off when the system is in S3/S4 sleep
state or powered off (S5).
HDLED (Hard Drive Activity LED):
Connect to the hard drive activity LED on the chassis front panel. The LED
is on when the hard drive is reading or writing data.

The front panel design may differ by chassis. A front panel module mainly
consists of power switch, reset switch, power LED, hard drive activity LED,
speaker and etc. When connecting your chassis front panel module to this
header, make sure the wire assignments and the pin assign-ments are
matched correctly.

Power LED Header Please connect the chassis

1
(3-pin PLED1) PLED- power LED to this header to
PLED+
(see p.13 No. 10) PLED+
indicate system power status.
The LED is on when the system
is operating. The LED keeps
blinking in S1 state. The LED is
off in S3/S4 state or S5 state
(power off).

Chassis Fan Connector Please connect the fan cables

(4-pin CHA_FAN1) to the fan connectors and
(see p.13 No. 5) match the black wire to the
ground pin.

CPU Fan Connectors 4 3 2 1

Please connect the CPU fan
(4-pin CPU_FAN1) cable to the connector and
(see p.13 No. 2) GND match the black wire to the
+12V
CPU_FAN_SPEED
FAN_SPEED_CONTROL ground pin.

Though this motherboard provides 4-Pin CPU fan (Quiet Fan) support, the 3-Pin
CPU fan still can work successfully even without the fan speed control function.
If you plan to connect the 3-Pin CPU fan to the CPU fan connector on this
motherboard, please connect it to Pin 1-3.
Pin 1-3 Connected

3-Pin Fan Installation

25
ATX Power Connector 12 24 Please connect an ATX power
(24-pin ATXPWR1) supply to this connector.
(see p.13 No. 4)

1 13

Though this motherboard provides 24-pin ATX power connector, 12 24

it can still work if you adopt a traditional 20-pin ATX power supply.
To use the 20-pin ATX power supply, please plug your
power supply along with Pin 1 and Pin 13.

20-Pin ATX Power Supply Installation 1 13

ATX 12V Power Connector Please connect an ATX 12V

(4-pin ATX12V1) power supply to this connector.
(see p.13 No. 1)

Chassis Intrusion Header This motherboard supports

(2-pin CI1) 1
CASE OPEN detection feature
GND
(see p.13, No. 15) Signal that detects if the chassis cover
has been removed. This feature
requires a chassis with chassis
intrusion detection design.

SPDIF Out Connector Please connect the

(2-pin SPDIF_OUT1) SPDIF_OUT connector of a
(see p.13, No. 19) HDMI VGA card to this header
with a cable.

26
LPC/TPM Header This connector supports
(13-pin LPC/TPM1) Trusted Platform Module (TPM)
(see p.13, No. 16) system, which can securely
store keys, digital certificates,
passwords, and data. A TPM
system also helps enhance
network security, protects
digital identities, and ensures
platform integrity.

PIN Signal Name PIN Signal Name

14 +3V 13 No pin
12 +3V 11 +3V
10 GND 9 GND
8 LAD3 7 LAD2
6 LAD1 5 LAD0
4 LFRAME# 3 RESET#
2 GND 1 CLK

27
2.9 Driver Installation Guide
To install the drivers to your system, please insert the support CD to your optical
drive first. Then, the drivers compatible to your system can be auto-detected and
listed on the support CD driver page. Please follow the order from up to bottom side
to install those required drivers. Therefore, the drivers you install can work properly.

28
 Chapter 3: UEFI SETUP UTILITY
3.1 Introduction
This section explains how to use the UEFI SETUP UTILITY to configure your
system. The UEFI chip on the motherboard stores the UEFI SETUP UTILITY. You
may run the UEFI SETUP UTILITY when you start up the computer. Please press
<F2> or <Del> during the Power-On-Self-Test (POST) to enter the UEFI SETUP
UTILITY, otherwise, POST will continue with its test routines.
If you wish to enter the UEFI SETUP UTILITY after POST, restart the system by
pressing <Ctl> + <Alt> + <Delete>, or by pressing the reset button on the system
chassis. You may also restart by turning the system off and then back on.

Because the UEFI software is constantly being updated, the
following UEFI setup screens and descriptions are for reference
purpose only, and they may not exactly match what you see on
your screen.

3.1.1 UEFI Menu Bar

The top of the screen has a menu bar with the following selections:
Main To set up the system time/date information
OC Tweaker To set up overclocking features
Advanced To set up the advanced UEFI features
Tool Useful tools
H/W Monitor To display current hardware status
Boot To set up the default system device to locate and load the
Operating System
Security To set up the security features
Exit To exit the current screen or the UEFI SETUP UTILITY
Use < > key or < > key to choose among the selections on the menu
bar, and then press <Enter> to get into the sub screen. You can also use the
mouse to click your required item.

29
 3.1.2 Navigation Keys
Please check the following table for the function description of each navigation
key.
Navigation Key(s) Function Description
/ Moves cursor left or right to select Screens
/ Moves cursor up or down to select items
+ / - To change option for the selected items
<Tab> Switch to next function
<Enter> To bring up the selected screen
<PGUP> Go to the previous page
<PGDN> Go to the next page
<HOME> Go to the top of the screen
<END> Go to the bottom of the screen
<F1> To display the General Help Screen
<F7> Discard changes and exit the UEFI SETUP UTILITY
<F9> Load optimal default values for all the settings
<F10> Save changes and exit the UEFI SETUP UTILITY
<F12> Print screen
<ESC> Jump to the Exit Screen or exit the current screen

3.2 Main Screen

When you enter the UEFI SETUP UTILITY, the Main screen will appear and display
the system overview.

30
3.3 OC Tweaker Screen
In the OC Tweaker screen, you can set up overclocking features.

CPU Configuration
CPU Ratio
Use this item to change the ratio value of this motherboard.
Intel SpeedStep Technology
Intel SpeedStep technology is Intel’s new power saving technology. Pro-
cessors can switch between multiple frequencies and voltage points to en-
able power saving. The default value is [Enabled]. Configuration options:
[Enabled] and [Disabled]. If you install Windows® VistaTM / 7 / 8 / 8.1 and
want to enable this function, please set this item to [Enabled]. This item
will be hidden if the current CPU does not support Intel SpeedStep tech-
nology.

Please note that enabling this function may reduce CPU voltage and lead to system
stability or compatibility issues with some power supplies. Please set this item to
[Disabled] if above issues occur.

Intel Turbo Boost Technology

Use this item to enable or disable Intel Turbo Boost Mode Technology.
Turbo Boost Mode allows processor cores to run faster than marked fre-
quency in specific conditions. The default value is [Enabled].
Long Duration Power Limit
Use this item to configure long duration power limit in watts. The default
value is [Auto].
Long Duration Maintained
Use this item to configure time window which the long duration power is
maintained. The default value is [Auto].

31
Short Duration Power Limit
Use this item to configure short duration power limit in watts. The default
value is [Auto].
Primary Plane Current Limit
Use this item to configure the maximum instantaneous current allowed for
the primary plane. The default value is [Auto].
Secondary Plane Current Limit
Use this item to configure the maximum instantaneous current allowed for
the secondary plane. The default value is [Auto].
GT OverClocking Support
Use this item to enable or disable GT OverClocking Support. The default
value is [Disabled].

DRAM Timing Configuration

Load XMP Setting
Use this to load XMP setting. Configuration options: [Auto], [Default], [Profile
1] and [Profile 2]. The default value is [Auto].
DRAM Frequency
If [Auto] is selected, the motherboard will detect the memory module(s)
inserted and assign the appropriate frequency automatically.

DRAM Configuration

DRAM tCL
Use this item to change CAS# Latency (tCL) Auto/Manual setting. The
default is [Auto].
DRAM tRCD
Use this item to change RAS# to CAS# Delay (tRCD) Auto/Manual setting.
The default is [Auto].

32
DRAM tRP
Use this item to change Row Precharge Time (tRP) Auto/Manual setting.
The default is [Auto].
DRAM tRAS
Use this item to change RAS# Active Time (tRAS) Auto/Manual setting.
The default is [Auto].
Command Rate (CR)
Use this item to change Command Rate (CR) Auto/Manual setting. The
default is [Auto].

DRAM tWR
Use this item to change Write Recovery Time (tWR) Auto/Manual setting.
The default is [Auto].
DRAM tRFC
Use this item to change Refresh Cyle Time (tRFC) Auto/Manual setting.
The default is [Auto].
DRAM tRRD
Use this item to change RAS to RAS Delay (tRRD) Auto/Manual setting.
The default is [Auto].
DRAM tWTR
Use this item to change Write to Read Delay (tWTR) Auto/Manual setting.
The default is [Auto].
DRAM tRTP
Use this item to change Read to Precharge (tRTP) Auto/Manual setting.
The default is [Auto].
DRAM tFAW
Use this item to change Four Activate Window (tFAW) Auto/Manual set-
ting. The default is [Auto].
DRAM tCWL
Use this item to change CAS# Write Latency (tCWL) Auto/Manual setting.
The default is [Auto].

ODT WR (CHA)
Use this item to change ODT WR (CHA) setting. The default is [Auto].
ODT WR (CHB)
Use this item to change ODT WR (CHB) setting. The default is [Auto].
ODT NOM (CHA)
Use this item to change ODT NOM (CHA) setting. The default is [Auto].
ODT NOM (CHB)
Use this item to change ODT NOM (CHB) setting. The default is [Auto].

33
MRC Fast Boot
Use this item to enable or disable MRC Fast Boot. The default is [Enabled].

Voltage Configuration
DRAM Voltage
Use this to select DRAM Voltage. The default value is [Auto].

34
3.4 Advanced Screen
In this section, you may set the configurations for the following items: CPU Configu-
ration, North Bridge Configuration, South Bridge Configuration, Storage Configura-
tion, Intel(R) Rapid Start Technology, Intel(R) Smart Connect Technology, Super IO
Configuration, ACPI Configuration and USB Configuration.

Setting wrong values in this section may cause

the system to malfunction.

35
3.4.1 CPU Configuration

Intel Hyper Threading Technology

To enable this feature, a computer system with an Intel processor that sup-
ports Hyper-Threading technology and an operating system that includes
optimization for this technology, such as Microsoft® Windows® XP / VistaTM
/ 7 / 8 / 8.1 is required. Set to [Enabled] if using Microsoft® Windows® XP,
VistaTM, 7, 8, 8.1 or Linux kernel version 2.4.18 or higher. This option will
be hidden if the installed CPU does not support Hyper-Threading technol-
ogy.
Active Processor Cores
Use this item to select the number of cores to enable in each processor
package. The default value is [All].
Enhance Halt State (C1E)
All processors support the Halt State (C1). The C1 state is supported
through the native processor instructions HLT and MWAIT and requires no
hardware support from the chipset. In the C1 power state, the processor
maintains the context of the system caches.
CPU C3 State Support
Use this to enable or disable CPU C3 (ACPI C2) report to OS.
CPU C6 State Support
Use this to enable or disable CPU C6 (ACPI C3) report to OS.
Package C State Support
Selected option will program into C State package limit register. The
default value is [Auto].

CPU Thermal Throttling

You may select [Enabled] to enable CPU internal thermal control
mechanism to keep the CPU from overheating.

36
No-Execute Memory Protection
No-Execution (NX) Memory Protection Technology is an enhancement
to the IA-32 Intel Architecture. An IA-32 processor with “No Execute (NX)
Memory Protection” can prevent data pages from being used by malicious
software to execute codes. This option will be hidden if the current CPU
does not support No-Excute Memory Protection.
Intel Virtualization Technology
When this option is set to [Enabled], a VMM (Virtual Machine Architecture)
can utilize the additional hardware capabilities provided by Vanderpool
Technology. This option will be hidden if the installed CPU does not
support Intel Virtualization Technology.
Hardware Prefetcher
Use this item to turn on/off the MLC streamer prefetcher.
Adjacent Cache Line Prefetch
Use this item to turn on/off prefetching of adjacent cache lines.

37
 3.4.2 North Bridge Configuration

Primary Graphics Adapter

This allows you to select [Onboard] or [PCI Express] as the boot graphic
adapter priority. The default value is [PCI Express].
VT-d
Use this to enable or disable Intel® VT-d technology (Intel® Virtualization
Technology for Directed I/O). The default value of this feature is [Disabled].

PCIE1 Link Speed

This allows you to select PCIE1 Link Speed. The default value is [Auto].
Share Memory
This allows you to set onboard VGA share memory feature. The default
value is [Auto].
IGPU Multi-Moniter
This allows you to enable or disable IGPU Multi-Moniter. The default value
is [Enabled]. If you install the PCI Express card under Windows® XP /
VistaTM OS, please disable this option.
Render Standby
Use this to enable or disable Render Standby by Internal Graphics Device.
The default value is [Enabled].

38
 3.4.3 South Bridge Configuration

Onboard HD Audio
Select [Auto], [Enabled] or [Disabled] for the onboard HD Audio feature. If
you select [Auto], the onboard HD Audio will be disabled when PCI Sound
Card is plugged.
Front Panel
Select [Auto] or [Disabled] for the onboard HD Audio Front Panel.
Onboard LAN
This allows you to enable or disable the Onboard LAN feature.

Deep Sleep
Mobile platforms support Deep S4/S5 in DC only and desktop platforms
support Deep S4/S5 in AC only. The default value is [Enabled in S5].
Restore on AC/Power Loss
This allows you to set the power state after an unexpected AC/power loss.
If [Power Off] is selected, the AC/power remains off when the power
recovers. If [Power On] is selected, the AC/power resumes and the
system starts to boot up when the power recovers.

Good Night LED

Use this item to enable or disable Power LED and LAN LED.

39
3.4.4 Storage Configuration

SATA Controller(s)
Use this item to enable or disable the SATA Controller feature.
SATA Mode Selection
Use this to select SATA mode. Configuration options: [IDE Mode], [AHCI
Mode] and [Disabled]. The default value is [AHCI Mode].

AHCI (Advanced Host Controller Interface) supports NCQ and other

new features that will improve SATA disk performance but IDE mode
does not have these advantages.

SATA Aggressive Link Power Management

Use this item to configure SATA Aggressive Link Power Management.
Hard Disk S.M.A.R.T.
Use this item to enable or disable the S.M.A.R.T. (Self-Monitoring, Analy-
sis, and Reporting Technology) feature. Configuration options: [Disabled]
and [Enabled].

40
3.4.5 Intel(R) Rapid Start Technology

Intel(R) Rapid Start Technology

Use this item to enable or disable Intel(R) Rapid Start Technology. Intel(R)
Rapid Start Technology is a new zero power hibernation mode which al-
lows users to resume in just 5-6 seconds. The default is [Enabled].

Entry After
Select a time to enable RTC wake timer at S3 entry. The default is [10
minutes].
Active Page Threshold Support
This allows you to enable or disable Active Page Threshold Support. The
default is [Disabled].

41
3.4.6 Intel(R) Smart Connect Technology

Intel(R) Smart Connect Technology

Use this item to enable or disable Intel(R) Smart Connect Technology.
Intel(R) Smart Connect Technology keeps your e-mail and social networks,
such as Twitter, Facebook, etc. updated automatically while the computer
is in sleep mode. The default is [Enabled].

42
3.4.7 Super IO Configuration

Serial Port
Use this item to enable or disable the onboard serial port.
Port Address
Use this item to set the address for the onboard serial port.
Configuration options: [3F8 / IRQ4] and [3E8 / IRQ4].
Infrared Port
Use this item to enable or disable the onboard infrared port.

43
3.4.8 ACPI Configuration

Suspend to RAM
Use this item to select whether to auto-detect or disable the Suspend-to-
RAM feature. Selecting [Auto] will enable this feature if the OS supports it.
Check Ready Bit
Use this item to enable or disable the feature Check Ready Bit.
ACPI HPET Table
Use this item to enable or disable ACPI HPET Table. The default value is
[Enabled]. Please set this option to [Enabled] if you plan to use this
motherboard to submit Windows® certification.

PS/2 Keyboard Power On

Use this item to enable or disable PS/2 keyboard to turn on the system
from the power-soft-off mode.
PCIE Device Power On
Use this item to enable or disable PCIE devices to turn on the system from
the power-soft-off mode.
Ring-In Power On
Use this item to enable or disable Ring-In signals to turn on the system
from the power-soft-off mode.
RTC Alarm Power On
Use this item to enable or disable RTC (Real Time Clock) to power on the
system.
USB Keyboard/Remote Power On
Use this item to enable or disable USB Keyboard/Remote to turn on the
system from the power-soft-off mode.
USB Mouse Power On
Use this item to enable or disable USB Mouse to turn on the system from
the power-soft-off mode.

44
CSM
Please disable CSM when you enable Fast Boot option. The default value
is [Enabled].

3.4.9 USB Configuration

USB 2.0 Controller

Use this item to enable or disable the use of USB 2.0 controller.
Legacy USB Support
Use this option to select legacy support for USB devices. There are four
configuration options: [Enabled], [Auto], [Disabled] and [UEFI Setup Only].
The default value is [Enabled]. Please refer to below descriptions for the
details of these four options:
[Enabled] - Enables support for legacy USB.
[Auto] - Enables legacy support if USB devices are connected.
[Disabled] - USB devices are not allowed to use under legacy OS and
UEFI setup when [Disabled] is selected. If you have USB compatibility is-
sue, it is recommended to select [Disabled] to enter OS.
[UEFI Setup Only] - USB devices are allowed to use only under UEFI
setup and Windows / Linux OS.

45
3.5 Tool

OMG(Online Management Guard)

Administrators are able to establish an internet curfew or restrict internet
access at specified times via OMG. You may schedule the starting and
ending hours of internet access granted to other users. In order to prevent
users from bypassing OMG, guest accounts without permission to modify
the system time are required.

UEFI Update Utility

Instant Flash
Instant Flash is a UEFI flash utility embedded in Flash ROM. This conve-
nient UEFI update tool allows you to update system UEFI without enter-
ing operating systems first like MS-DOS or Windows®. Just save the new
UEFI file to your USB flash drive, floppy disk or hard drive and launch this
tool, then you can update your UEFI only in a few clicks without prepar-
ing an additional floppy diskette or other complicated flash utility. Please
be noted that the USB flash drive or hard drive must use FAT32/16/12 file
system. If you execute Instant Flash utility, the utility will show the UEFI
files and their respective information. Select the proper UEFI file to up-
date your UEFI, and reboot your system after the UEFI update process is
completed.
Internet Flash
Internet Flash searches for available UEFI firmware updates from our
servers. In other words, the system can auto-detect the latest UEFI from
our servers and flash them without entering Windows OS.

46
Network Configuration

Internet Setting
Use this item to set up the internet connection mode. Configuration
options: [DHCP (Auto IP)] and [PPPOE].
UEFI Download Server
Use this item to select UEFI firmware download server for Internet Flash.
Configuration options: [Asia], [Europe], [USA] and [China].

Dehumidifier Function
Users may prevent motherboard damages due to dampness by enabling
“Dehumidifier Function”. When enabling Dehumidifier Function, the com-
puter will power on automatically to dehumidify the system after entering
S4/S5 state.
Dehumidifier Period
This allows users to configure the period of time until the computer powers
on and enables “Dehumidifier” after entering S4/S5 state.
Dehumidifier Duration
This allows users to configure the duration of the dehumidifying process
before it returns to S4/S5 state.
Dehumidifier CPU Fan Setting
Use this setting to configure CPU fan speed while “Dehumidifier” is en-
abled.

Would you like to save current setting user defaults?

In this option, you are allowed to load and save three user defaults
according to your own requirements.

47
3.6 Hardware Health Event Monitoring Screen
In this section, it allows you to monitor the status of the hardware on your system,
including the parameters of the CPU temperature, motherboard temperature, CPU
fan speed, chassis fan speed, and the critical voltage.

CPU Fan 1 Setting

This allows you to set the CPU fan 1 speed. Configuration options: [Full
On] and [Automatic Mode]. The default is value [Full On].
Chassis Fan 1 Setting
This allows you to set the Chassis fan 1 speed. Configuration options: [Full
On] and [Automatic Mode]. The default is value [Full On].
Case Open Feature
This allows you to enable or disable case open detection feature. The
default is value [Enabled].
Clear Status
This option appears only when the case open has been detected. Use this
option to keep or clear the record of previous chassis intrusion status.

48
3.7 Boot Screen
In this section, it will display the available devices on your system for you to config-
ure the boot settings and the boot priority.

Fast Boot
Fast Boot minimizes your computer’s boot time. There are three con-
figuration options: [Disabled], [Fast] and [Ultra Fast]. The default value is
[Disabled]. Please refer to below descriptions for the details of these three
options:
[Disabled] - Disable Fast Boot.
[Fast] - The only restriction is you may not boot by using an USB flash
drive.
[Ultra Fast] - There are a few restrictions.
1. Only supports Windows® 8.1 / 8 UEFI operating system.
2. You will not be able to enter BIOS Setup (Clear CMOS or run utility
in Widows® to enter BIOS Setup).
3. If you are using an external graphics card, the VBIOS must support
UEFI GOP in order to boot.

Boot From Onboard LAN

Use this item to enable or disable the Boot From Onboard LAN feature.

Setup Prompt Timeout

This shows the number of seconds to wait for setup activation key.
65535(0xFFFF) means indefi nite waiting.
Bootup Num-Lock
If this item is set to [On], it will automatically activate the Numeric Lock
function after boot-up.

49
Full Screen Logo
Use this item to enable or disable OEM Logo. The default value is [En-
abled].
AddOn ROM Display
Use this option to adjust AddOn ROM Display. If you enable the option “Full
Screen Logo” but you want to see the AddOn ROM information when the
system boots, please select [Enabled]. Configuration options: [Enabled]
and [Disabled]. The default value is [Enabled].

Boot Failure Guard

Enable or disable the feature of Boot Failure Guard.
Boot Failure Guard Count
Enable or disable the feature of Boot Failure Guard Count.

50
3.8 Security Screen
In this section, you may set or change the supervisor/user password for the system.
For the user password, you may also clear it.

Secure Boot
Use this to enable or disable Secure Boot. The default value is [Disabled].

51
3.9 Exit Screen

Save Changes and Exit

When you select this option, the following message “Save configuration
changes and exit setup?” will pop-out. Select [Yes] to save the changes
and exit the UEFI SETUP UTILITY.
Discard Changes and Exit
When you select this option, the following message “Discard changes and
exit setup?” will pop-out. Select [Yes] to exit the UEFI SETUP UTILITY
without saving any changes.
Discard Changes
When you select this option, the following message “Discard changes?”
will pop-out. Select [Yes] to discard all changes.
Load UEFI Defaults
Load UEFI default values for all the setup questions. F9 key can be used
for this operation.

Launch EFI Shell from filesystem device

Attempts to Launch EFI Shell application (Shell64.efi) from one of the
available filesystem devices.

52
 Chapter 4: Software Support
4.1 Install Operating System
This motherboard supports various Microsoft® Windows® operating systems: 8.1 /
8.1 64-bit / 8 / 8 64-bit / 7 / 7 64-bit / VistaTM / VistaTM 64-bit / XP / XP 64-bit. Because
motherboard settings and hardware options vary, use the setup procedures in this
chapter for general reference only. Refer to your OS documentation for more infor-
mation.

4.2 Support CD Information

The Support CD that came with the motherboard contains necessary drivers and
useful utilities that enhance the motherboard features.

4.2.1 Running The Support CD

To begin using the support CD, insert the CD into your CD-ROM drive. The
CD automatically displays the Main Menu if “AUTORUN” is enabled in your
computer. If the Main Menu did not appear automatically, locate and double
click on the file “ASRSETUP.EXE” from the BIN folder in the Support CD to
display the menus.

4.2.2 Drivers Menu

The Drivers Menu shows the available devices drivers if the system detects
installed devices. Please install the necessary drivers to activate the devices.

4.2.3 Utilities Menu
The Utilities Menu shows the applications software that the motherboard sup-
ports. Click on a specific item then follow the installation wizard to install it.

4.2.4 Contact Information

If you need to contact ASRock or want to know more about ASRock, welcome
to visit ASRock’s website at http://www.asrock.com; or you may contact your
dealer for further information.

53
Installing OS on a HDD Larger Than 2TB
This motherboard is adopting UEFI BIOS that allows Windows® OS to be installed
on a large size HDD (>2TB). Please follow below procedure to install the operating
system.

1. Please make sure to use Windows® VistaTM 64-bit (with SP1 or above),
Windows® 7 64-bit or Windows® 8.1 / 8 64-bit.
2. Press <F2> or <Delete> at system POST. Set AHCI Mode in UEFI Setup Utility >
Advanced > Storage Configuration > SATA Mode.
3. Choose the item “UEFI:xxx“ to boot in UEFI Setup Utility > Boot > Boot Option #1.
(“xxx” is the device which contains your Windows® installation files. Normally it is
an optical drive.) You can also press <F11> to launch boot menu at system POST
and choose the item “UEFI:xxx“ to boot.
4. Start Windows® installation.
5. If you install Windows® 7 64-bit OS, OS will be formatted by GPT (GUID Partition
Table). Please install the hotfix file from Microsoft®:
http://support.microsoft.com/kb/979903

54