Bit Box

Price for BitBox
Name Description Price, Eur.

Toyota
Module for OBD virtual reading and writing
with CAN-bus Toyota Denso Gen1 ECUs used
Toyota Denso Gen1 CAN 250.00
in Toyota/Lexus/Scion/Hino petrol and diesel
vehicles.
Module for OBD reading/virtual reading and
Toyota Denso Gen2 writing Toyota Denso newGen ECUs used in
250.00
(newGen) CAN Toyota&Lexus petrol and diesel vehicles.
Checksum correction included.
Module for OBD reading and writing with
Toyota Denso Gen3 CAN CAN-bus Toyota Denso Gen3 ECUs used in 250.00
Toyota/Lexus petrol vehicles.
Module for OBD virtual reading and writing
Toyota Delphi Gen1 CAN with CAN-bus Toyota Delphi Gen1 ECUs used 100.00
in Toyota and Scion petrol vehicles.
Module for software identification and virtual
reading of Denso ECUs on Toyota, Scion,
Toyota Gen1 Virtual Reader 120.00
Lexus and Hino vehicles. No writing
supported.
Package of 5 modules with discount for
Toyota Full package 850.00
Toyota/Lexus/Scion/Hino vehicles.
+98 51 38 64 41 19 info@Carsoft-Tech.com
+98 912 067 6004 www.Carsoft-Tech.com
BMW
Module for reading and writing via diagnostic
BMW GearBox connector TCMs Siemens GS20 and Bosch 100.00
GS8.60.2 used on BMW vehicles.
Module for reflashing through OBD2
BMW Exx Bosch CAN connector by CAN-bus Bosch ECUs used in
350.00
BMW Exx vehicles. No need to dismount,
open or drill an ECU - FULL OBD2 solution.
BMW Fxx Bosch ENET connector by Ethernet for Bosch ECUs used in
350.00
BMW Fxx vehicles. No need to dismount,
open or drill an ECU - FULL OBD2 solution.
BMW Fxx/Gxx Bosch connector by Ethernet for Bosch MG1 and
350.00
MG1/MD1 ENET MD1 ECUs used in BMW Fxx and Gxx
vehicles.
Package of all 3 modules we have for BMW
BMW Full CAN+ENET with discount. BMW Bosch Exx CAN + Fxx 900.00
Bosch ENET + Fxx/Gxx Bosch MG1/MD1 ENET
Mercedes-Benz
Module for reading and writing through the
MB Bosch EDC17 CAN diagnostic connector by CAN-bus for diesel
250.00
Mercedes-Benz vehicles with Bosch EDC17
ECUs.
Module for virtual reading and writing
through the diagnostic connector by CAN-bus
MB Bosch MED17 CAN 250.00
for petrol Mercedes-Benz vehicles with Bosch
MED17 ECUs.
Module for reading and writing by CAN-bus
MB Siemens/Continental for petrol Mercedes-Benz vehicles with
200.00
SIM271 Siemens/Continental SIM271 ECUs. Full OBD2
solution.
FCA group
diagnostic connector Chrysler/Dodge/Jeep
FCA Petrol Gen1 CAN 300.00
petrol vehicles with Motorola NGC3, NGC4,
NGC4A and Continental GPEC, GPEC2 ECUs.
diagnostic connector
FCA Petrol Gen2 CAN Chrysler/Dodge/Jeep/Fiat petrol vehicles with 300.00
Continental GPEC2 LOCKED, GPEC2A and
GPEC3 ECUs.
FCA Bosch Diesel CAN diagnostic connector by CAN-bus for diesel
250.00
Chrysler/Dodge/Jeep and Fiat vehicles with
Bosch ECUs.
Korea
Module for OBD reading and writing Delphi
SsangYong Delphi Diesel 200.00
DCM ECUs used in SsangYong diesel vehicles.
Module for OBD reading and writing Siemens
SsangYong Siemens Petrol 200.00
ECUs used in SsangYong petrol vehicles.
Module for OBD reflash for ECUs used in
Kia/Hyundai Diesel 250.00
diesel Kia/Hyundai vehicles.
Kia/Hyundai Petrol CAN 200.00
ECUs used in petrol Kia and Hyundai vehicles.
Module for reading and writing in BSL mode
Kia/Hyundai Continental
for Continental SIM2K-250/251/253/258/260 200.00
SIM2K-25x/26x
ECUs used in petrol Kia and Hyundai vehicles.
China
Software module for reading and writing
China Delphi Petrol Delphi ECUs internal flash memory for China 140.00
vehicles with petrol engines.
Siemens/Continental ECUs internal flash
China Siemens Petrol 100.00
memory for China vehicles with petrol
engines.
China Bosch Petrol Bosch ECUs internal flash memory for China 140.00
Volvo
Module for reading and writing on the Bench
Volvo Denso SH72xxx CAN through CAN-bus for diesel and petrol Volvo 200.00
vehicles with Denso SH72xxx ECus.
GM
Module for reading and writing through OBD2
GM Diesel CAN connector by CAN-bus ECUs used in diesel GM 200.00
vehicles (Opel, Chevrolet, Saab, Holden).
GM ACDelco Petrol Gen1 CAN connector by CAN-bus ACDelco Gen1 ECUs 350.00
used in petrol GM vehicles.
VAG group
ECUs Magneti Marelli IAW 4HV, 7GV, 7GVE,
VAG Marelli Petrol 9GV. This ecu is used on VAG vehicles with 100.00
CFNA, CFNB, CLRA, CLPA, CLPB, CGGB, CFZA
engines.
PSA Group
PSA Diesel CAN connector by CAN-bus ECUs used in Peugeot 200.00
and Citroen deisel vehicles.
Trucks/Industrial
connector by CAN-bus Bosch EDC17CV41
Trucks/Industrial Bosch
ECUs used in trucks/industrial vehicles Tata- 400.00
EDC17CV41
Daewoo, New Holland, CASE, CLAAS, Iveco,
Doosan.
Trucks Delphi DMCI CAN Delphi DMCI ECUs used in DAF and Hyundai 300.00
trucks.
Moto/Extreme
through the diagnostic connector Delphi
Delphi MT05 250.00
MT05 and MT05.2 ECUs on different moto
vehicles.
Module for software identification and virtual
China Bosch Moto/Extreme reading and writing Bosch MSE 3.0, MSE6.0 250.00
and US6.0 ECUs
Module for reading and writing extrime
vehicles with Rotax engines and ECUs Bosch
Rotax Extreme 250.00
ME17.8.5 and Siemens MSE 3.7x. Checksum
correction included.
Module for OBD reading and writing Harley-
Harley-Davidson Delphi 200.00
Davidson motorbikes with Delphi ECUs.
Module for identification and virtual reading
Moto/Extreme Denso Virtual
of Denso SH7052 ECUs on Arctic Cat and 100.00
Reader
Suzuki vehicles. No writing supported.
Module for software identification (ID), virtual
MV Agusta Eldor reading and writing Eldor EM 2.0 ECUs used 100.00
in motobikes MV Agusta.
Module for OBD reading and writing BMW
BMW Motorrad
Motorrad motorbikes with Bosch and Magneti TEST
Marelli ECUs.
Master/Slave
BitBox Slave initial purchace. Includes 1
BitBox Slave initial dongle and subscription for 12 months. 250.00
Available only for Master dongle owners.
Accessories
Device that connects through USB port and
USB Dongle makes identification of the user and 38
activated licenses
Adapter CF Moto 3pin-to-OBD2 adapter is
designed to connect OpenPort 2.0 or any
Adapter CF Moto 3pin-to-OBD2 50
device with built-in OBD2 Male to the
diagnostic connector of CF Moto vehicles.
Adapter 6pin-to-OBD2 adapter is designed
to connect J2534 adapter or any device with
Adapter 6pin-to-OBD2 built-in OBD2 Male to 6-pin diagnostic 50
connector of different extreme vehicles like
ATVs, UTVs and motorcycles made in China.
Adapter BRP 6pin-to-OBD2 is designed to
connect OpenPort 2.0 or any device with
Adapter BRP 6pin-to-OBD2 50
built-in OBD2 Male to the diagnostic
connector of BRP vehicles.
Adapter BRP 6pin-to-OBD2 is designed to
connect OpenPort 2.0 or any device with
Adapter HD 6pin-to-OBD2 50
connector of Harley-Davidson vehicles.
Power adapter BITS001 bench ECU
connection. Mandatory to use for
Power adapter BITS001 60
Continental SIM2K-25x/26x and for BSL
reading of Bosch M7.8/ME7.8.8 ECUs.
Adapter BMW 10pin-to-OBD2 is designed to
connect J2534 adapter or any device with
Adapter BMW 10pin-to-OBD2 50
connector of BMW Motorrad vehicles.
Module Toyota Denso Gen1 CAN
FID: 24, 26
Module for OBD virtual reading and writing with CAN-bus Toyota Denso and Fujitsu
Ten Gen1 ECUs used in Toyota/Lexus/Scion/Hino petrol and diesel vehicles.
Toyota Denso NEC 76F00XX (FID: 24)

Toyota Denso NEC TCM 76F00XX (FID: 26) - test
It supports working with ECM and TCM of Denso ECUs with CAN-bus and based on
MCUs NEC 76F0038, 76F0039, 76F0040, 76F0070 и 76F0085.
Module allows:
- Software identification
- Virtual reading lastest software update
- Writing (update version or downgrade)
- Checksums and CVN correction
- Recovery from any state*
* This feature allows to recovery ECU broken (with any tool) during CANBus writing or
while Techstream update. You don't need any NBD/JTAG device, it CAN BE DONE with
J2534 device via CANBus with bootstrap mode. This feature allows easy recovery of
ECUs, including LC200 4.5TD without hard opening of the case and neccessary access
to back side of PCB, and also new ECUs without NBD/JTAG pins on PCB (for example
Camry V50, Highlander 3.5 U50, etc.).
Price: 250 Eur.
Module Toyota Denso Gen2 (newGen) CAN
FID: 23, 27, 28
Module for OBD reading/virtual reading and

writing Toyota Denso newGen ECUs used in
Toyota&Lexus petrol and diesel vehicles.
Checksum correction included.
Module supports 2 protocols types:
TYPE 1 (FID: 23, 27)

Allowed FullFlash READING and WRITING Toyota&Lexus petrol vehicles with 2.0
6ARFSE, 2.0T 8ARFTS, 1.2T 8NRFTS, 3.5 2GRFKS, 3.5 7GRFSE etc. engines via P5-CAN-
bus.
 Engine MCU D76F0199GD 1280Kb
 Engine MCU D76F0196F1 1536Kb
 Transmission MCU D76F0199GD 1280Kb
 Transmission MCU D76F0196F1 1536Kb
Also this FID allows to set READ PROTECTIN PATCH which will disable ECU reading and will
protect your MOD files from stole.
Supported vehicles: Supported engines:

Lexus NX 200t AGZ1# 2.0 6AR-FSE
Lexus IS 200t ASE30 2.0 8AR-FTS
Lexus GS 200t ARL10 1.2 8NR-FTS
Lexus RX 200t AGL2# 3.5 2GR-FKS
Lexus RC 200t ASC10 3.5 7GR-FSE
Lexus ES 200 ASV61 3.5hyb 8GR-FXS
Toyota Auris 1.2t NRE185 1.8hyb 2ZR-FXE
Toyota Camry 2.0 ASV51 etc...
Toyota Crown 2.0t
Toyota Tacoma 3.5 GRN3##
Lexus GS 350 GRL1#
Lexus RX 350 GGL2#
Toyota Highlander 2.0t ASU5#
Toyota C-HR 1.2t NGX##
TYPE 2 (FID: 28)

Allowed FullFlash VIRTUAL READING and WRITING with CS and CVN correction for
Toyota&Lexus diesel and NA petrol vehicles with 2.8TD 1GDFTV, 2.4TD 2GDFTV, 4.0
1GRFE, 2.7 2TRFE, 2NRFE, 3ZRFAE engines. Writing possible ONLY if we have file for
your vehicle on our server.
We will not respond to the claims about the inability to read a file from our server if we
do not have it. Supported files list can be found here.
 Engine MCU D76F0199GD 1280Kb


Toyota C-HR ZGX10L 2.8TD 1GDFTV
Toyota HiLUX GUN## 2.4TD 2GDFTV
Toyota LC150 Prado GDJ##, GRJ15# 4.0 1GRFE
Toyota Tacoma TRN2## 2.7 2TRFE
Toyota Yaris 1.5 NSP151 5.0 2URGSE
Lexus RC-F USC10 1.5 2NRFE
Lexus GS-F URL10 2.0 3ZRFAE
Lexus RX450h GYL2# etc...
Price: 250 Eur.
Module Toyota Denso Gen3 CAN
FID: 149
Module for OBD reading and writing with CAN-bus Toyota Denso and Fujitsu Ten Gen3
ECUs used in Toyota/Lexus petrol vehicles with new Dynamic Force engines.
Toyota Denso Gen3 R7F701202 (FID: 149)

Supports Denso ECUs based on MCU Renesas R7F701202 with 4Mb flash memory.
Module allows:
- Reading
- Writing with checksumm correction
- Recovery after any fail

Lexus ES250 ES300h (ZA10, ZH10) 2.0 M20AFKS
Lexus LS500 (F5) 2.0hyb M20AFXS
Lexus UX200, UX200h (X10) 2.5 A25AFKS
Toyota Auris/Corolla 2.0, 2.0hyb (E21) 2.5hyb A25AFXS
Toyota Avalon 2.5hyb (XH5) 2.5hyb A25BFXS
Toyota Camry 2.5, 2.5hyb (VA70, VH70) 3.5turbo V35AFTS
Toyota C-HR 2.0 (X10) etc...
Toyota Crown 2.0hyb (SH20)
Toyota RAV4 2.0, 2.0hyb (A50)
etc...
Price: 250 Eur.
Module Toyota Delphi Gen1 CAN
FID: 140
Module for OBD virtual reading and writing with CAN-bus Toyota Delphi Gen1 ECUs
used in Toyota and Scion petrol vehicles.
Toyota Delphi MPC565/SH72xx (FID: 140)

Module supports 3 types of Delphi ECUs based on different MCUs: Motorola MPC565,
Renesas SH72544 & SH72512
Supported filesize: 1Mb, 1.5Mb, 2Mb
Module allows:
- Virtual reading lastest software update
- Writing (update version or downgrade)
- Recovery from any state
Module supports only CANbus vehicles.
Price: 100 Eur.
Module Toyota Gen1 Virtual Reader
FID: 8, 9, 22
Service module for identification and virtual

reading Toyota, Scion, Lexus and Hino Denso
and Delphi Gen1 ECUs with NEC MCUs
76F0004/15/23/38/39/40/70/85 and Motorola
MPC565 .
It allows to get ID of the firmware through OBD connector with any J2534 adapter and
if this firmware available on our server You can download it for FREE.
Toyota Gen1 ECM Virtual reader (FID: 8)

Toyota Denso Gen1 TCM Virtual reader (FID: 9)
Toyota Denso Gen1 HCM Virtual reader (FID: 22)
Attention! We are not provide WRITING. U can use this module for stock files getting for
acquaintance.
Our base is now contains 4000+ files.
Attention! We are not provide ORI files by mail, skype etc. You have to use this module
to get file in the car.
do not have it.
Denso newGen (Gen2) files 1.25, 1.5 and 2.0 Mb available only for owners of Toyota
Denso newGen CAN module.
Price: 120 Eur.
Module Toyota Full package
Package of 5 modules with discount for Toyota/Lexus/Scion/Hino vehicles.
Package includes:
- Toyota Denso Gen1 CAN
- Toyota Denso Gen2/newGen CAN
- Toyota Denso Gen3 CAN
- Toyota Delphi Gen1 CAN
- Toyota Gen1 Virtual Reader
Price: 850 Eur.
Module BMW GearBox
FID: 3, 4
Module for reading and writing via diagnostic

connector TCM Siemens GS20 and Bosch
GS8.60.2 used on BMW vehicles.
Bosch GS8.60.2 (FID: 3)

This type of TCM is set to BMW vehicles
equipped with Automatic transmission models of ZF 5HP24. Supports to read
calibration area, writing and correction checksum through the diagnostic connector.
BMW E38 735
BMW E38 740
BMW E38 730d
BMW E39 535
BMW E39 540
Siemens GS20 (FID: 4)
ECU Siemens GS20 installed on the BMW with boxes of General Motors 5L40. Supports
read/write field calibration with automatic correction checksums through the
diagnostic connector.
BMW E38 730d
BMW E39 530d
BMW E39 525d
BMW E53 X5 3.0d
Price: 100 Eur.
Module BMW Exx Bosch CAN
FID: 46, 47, 48, 49, 50, 135, 136, 137
Module for reflashing through OBD2 connector by CAN-bus Bosch ECUs used in BMW
Exx vehicles. No need to dismount, open or drill an ECU - FULL OBD2 solution.
Allows VIRTUAL reading and writing of calibration area.
Module is now supports:
 Bosch EDC17CP45 (DDE7.3.1)

 Bosch EDC17CP02 (DDE7.1)
 Bosch EDC17C06 (DDE7.0)
 Bosch EDC17CP09 (DDE7.3)
 Bosch EDC17C41 (DDE7.2.1)
 Bosch EDC17C50 (DDE7.0.1)
 Bosch MEVD17.2
 Bosch MEVD17.2.9
Other ECU types will be added as soon as possible.
do not have it.
Price: 350 Eur.
Module BMW Fxx Bosch ENET
FID: 130, 132, 133
Module for reflashing through OBD2 connector by Ethernet for Bosch ECUs used in
diesel BMW Fxx vehicles. No need to dismount, open or drill an ECU - FULL OBD2
solution.
Warning! Module doesn’t work with J2534 adapter, BMW ENET-to-OBD2 cable is
required for work. Also this family can’t work on the bench!
Module allows:
• Identification
• Virtual Reading
• Writing program and maps
• CS and CVN fix on writing
• Recovery with original file (as official BMW diagnostic system)
• Reading and writing coding data
• DTC reading / clearing
Supported diesel ECUs:
• Bosch EDC17C41 (DDE7.2.1)

• Bosch EDC17CP45 (DDE7.3.1)
• Bosch EDC17CP49 (DDE7.5.1)
• Bosch EDC17CP09 (DDE7.3a)
Supported petrol ECUs:
• Bosch MEVD17.2
• Bosch MEVD17.2.4
• Bosch MEVD17.2.G (incl. S55)
• Bosch MEVD17.2.H
do not have it.
Price: 350 Eur.
Module BMW Fxx/Gxx Bosch MG1/MD1 ENET
FID: 160, 161
Module for reflashing through OBD2 connector

by Ethernet for Bosch MG1 and MD1 ECUs used
in BMW Fxx and Gxx vehicles.
Supports Bosch ECUs based on MCU NXP MPC5777 with 7.5Mb of main flash memory.
BMW Fxx/Gxx Bosch MG1 MPC5777 ENET (FID: 160)

BMW Fxx/Gxx Bosch MD1 MPC5777 ENET (FID: 161)
Module allows:
 Software identification
 Virtual reading from server
 Reading if file not found in server
 Writing with checksumm and CVN correction
 DTC read and clear
Price: 350 Eur.
Module BMW Full CAN+ENET
Package of all 3 modules we have for BMW with discount. BMW Bosch Exx CAN + Fxx
Bosch ENET + Fxx/Gxx Bosch MG1/MD1 ENET.
Price: 900 Eur.
Module MB Bosch EDC17 CAN
FID: 200, 201, 202
Module for reading and writing through the diagnostic connector by CAN-bus for diesel
Mercedes-Benz vehicles with Bosch EDC17 ECUs.
Supported ECU types:

 Bosch EDC17CP01 / EDC17CP10 (FID: 200)
 Bosch EDC17CP57 / EDC17CP60 / EDC17C66 (FID: 201)
 Bosch EDC17CP46 (FID: 202)
 Bosch EDC17C43 (FID: 206)
 Bosch EDC17CP01 with no ext. flash (FID:207) /TEST/
Module allows:
 SW identification
 Reading of calibration area
 Writing of calibration area
 CS correction
Price: 250 Eur.
Module MB Bosch MED17 CAN
FID: 203, 204, 205, 208
Module for virtual reading and writing through the diagnostic connector by CAN-bus for
petrol Mercedes-Benz vehicles with Bosch MED17 ECUs.
Supported ECU types:

 MB Bosch MED17.7.1 / MED17.7.3 (FID: 205)
 MB Bosch MED17.7.3.1 (FID: 204)
 MB Bosch MED17.7.2 (FID: 203)
 Infiniti Bosch MED17.7.2 (FID: 208)
Module allows:
 SW identification
 Virtual Reading of calibration area (850+ files in a base)
 Writing of calibration area
 CS correction
Price: 250 Eur.
Module MB Siemens/Continental SIM271
Module for reading and writing by CAN-bus for petrol Mercedes-Benz vehicles with
Siemens/Continental SIM271 ECUs.
Continental SIM271DE2.0 (FID: 209)

ECU is based on MCU Infineon Tricore TC1796 with internal flash memory 2Mb.
Allows reading of calibration area and writing with checksumm correction by CANbus.
Full OBD2 solution.
Siemens SIM271KE2.0 (FID: 213)

ECU is based on MCU Infineon Tricore TC1796 with internal flash memory 2Mb.
Allows reading of calibration area and writing with checksumm correction by CANbus.
No need to open ECU. Full OBD2 solution.
Price: 200 Eur.
Module FCA Petrol Gen1 CAN
FID: 12, 13, 14, 15, 16, 17

diagnostic connector by CAN-bus
Chrysler/Dodge/Jeep and Fiat petrol vehicles with
Motorola NGC3, NGC4, NGC4A and Continental
GPEC, GPEC2 ECUs.
Also its possible to work on the bench with no

openning ECU.
Module allows to Identify, Read FullFlash, Write calibration area and automatically
correct CheckSums on writing.
 Motorola NGC3 MPC565 1Mb (FID: 12)

 Motorola NGC4 MPC5554 2Mb (FID: 13)
 Motorola NGC4A MPC5554 2Mb (FID: 15)
 Continental GPEC (SIM90) MPC561+EXT.FLASH 2Mb (FID: 16)
 Continental GPEC2 MPC5566 3Mb (FID: 14)*
* - for vehicles till 2014. Newer cars have ECUs with RSA LOCK and need to be
UNLOCKED before writing. This new ECUs need to use with module FCA Petrol Gen2
CAN If you are not sure about what ECU you have to work please contact sales
department before ordering.
Price: 300 Eur.
Module FCA Petrol Gen2 CAN
FID: 18, 19, 20, 21
Software module for OBD2 working with FCA

group vehicles (Chrysler/Dodge/Jeep/Fiat) with
ECUs Continental GPEC2 LOCKED, GPEC2A,
GPEC3.
This ECUs are used on normal aspirated petrol

cars from 2013 and have internal protection from tuning (LOCK).
For success MOD file writing it needs to remove protection (ECU Unlock) in BSL mode.
You will need to open ECU and connect it on the bench as shown in connection
manual.
This is the world first solution with no need to send ECU to any workshop for PCM
modification. All you can do by yourself.
Module allows this operations:
 Identification and getting LOCK status (LOCKED/ UNLOCKED)

 OBD2 FULLFLASH reading
 OBD2 EEPROM reading
 ECU Unlock in BSL mode
 OBD2 Calibration area writing
 OBD2 EEPROM writing
 Read and clear DTC
At this moment we support this ECU types:
 Continental GPEC2 2013+ MPC5566 3Mb (FID: 20)

 Continental GPEC2 2015+ MPC5566 3Mb (FID: 21)
 Continental GPEC2A MPC5674 4Mb (FID: 19)
 Continental GPEC2A 2018+ MPC5674 4Mb (FID: 131)
 Continental GPEC3 MPC5674 4Mb (FID: 18)
Attention! UNLOCK function is not working now with all J2534 adapters. Currently we
tested and guarantee correct unlock with CarDAQ Plus, Bosch VCM2, Mongoose (excl.
ISO).
Unlock does not work with Tactrix OpenPort 2.0, Chipsoft J2534, SMS Soft Dialink.
Price: 300 Eur.
Module FCA Bosch Diesel CAN
FID: 106, 107, 108, 124
Module for reading and writing through the diagnostic connector by CAN-bus for diesel
Chrysler/Dodge/Jeep and Fiat vehicles with Bosch ECUs.
FCA Bosch EDC17C49 (FID: 106)

Engine control unit is based on MCU Infineon Tricore TC1797 with internal flash
memory 4.0 Mb.
Module allows virtual reading and writing of calibration area by OBD2 with checksumm
correction on writing.
FCA Bosch EDC17C79 (FID: 107)

memory 4.0 Mb.
FCA Bosch EDC17CP27 (FID: 108)

memory 2.0 Mb.
FCA Bosch EDC17C49/C79 Reader (FID: 124)

Allows real reading of calibration area on the BENCH by CANbus with checksumm
checking. Needs if virtual reader cannot fnd file for your vehicle.
Price: 250 Eur.
Module SsangYong Delphi Diesel
FID: 32, 33, 34, 89
Module for OBD reading and writing Delphi

ECUs used in SsangYong diesel vehicles.
SsangYong Delphi DCM6.2AP (FID: 32)

ECU based on MCU NXP SPC5673 with internal
memory 3Mb.
Allows to read and write calibration area via CAN-bus with CHK calculation. Recovery is
possible from any state.
Supported vehicles:
SsangYong Tivoli/XLV D16DTF
SsangYong Rodius/Stavic II D22DTR
SsangYong Korando C/New Actyon D22DTF
SsangYong Rexton G4 D22DTR
SsangYong Delphi DCM6.2AP-6D (FID: 89)

ECU based on MCU NXP SPC5674 with internal memory 4Mb.
Supported vehicles:
SsangYong Rexton G4 D22DTR-SCR
ECU based on MCU Renesas SH72513 with internal memory 2Mb.
Allows to read FullFlash and write calibration area via CAN-bus with CHK calculation.
Supported vehicles:
SsangYong Actyon Sports D20DTR
SsangYong Korando C/New Actyon D20DTF
SsangYong Rexton D20DTR
SsangYong Rodius D20DTR
SsangYong Stavic II D20DTR

ECU based on MCU Motorola MPC563 +external flash AM29BDD160GB with total
memory adress area 2.5Mb.
Allows to read FullFlash, write with CHK calculation by K-line.
Supported vehicles:
SsangYong Actyon D20DT Euro4
SsangYong Actyon Sports D20DT Euro4
SsangYong Kyron D20DT Euro4
SsangYong Rexton D20DT Euro4
SsangYong Rexton D27DT Euro4
SsangYong Rodius D27DT Euro4
SsangYong Delphi DCM3.1 (FID: 34)

ECU based on MCU Motorola MPC555 with internal memory 448Kb.
Allows to read FullFlash and write calibration area via K-line with CHK calculation.
Supported vehicles:
SsangYong Actyon D20DT Euro3
SsangYong Actyon Sports D20DT Euro3
SsangYong Rodius D27DT Euro3
Tata Safari 3.0 DiCOR
Tata Xenon 3.0 DiCOR
Price: 200 Eur.
Module SsangYong Siemens Petrol
FID: 40, 45
Module for OBD reading and writing Siemens ECUs used in SsangYong petrol vehicles.
Siemens SIM2K-410 (FID: 40)

Engine control unit Siemens SIM2K-410 based on MCU NXP SPC5634 with internal
flash memory 1.5 Mb.
This ECU is used on SsangYong petrol vehcles with 1.6 G16DF engine. Allows virtual
reading and writing of FullFlash by OBD2 with checksumm correction on writing.
Supported vehicles:
SsangYong Tivoli 1.6 G16DF
SsangYong Tivoli XLV 1.6 G16DF
Siemens SIM2K-C201 (FID: 45)

Engine control unit Siemens SIM2K-C201 based on MCU Infineon Tricore TC1767 with
internal flash memory 2.0 Mb.
This ECU is used on SsangYong petrol vehcles with 2.0 G20DF engine. Allows reading
and writing of FullFlash by OBD2 with checksumm correction on writing.
Supported vehicles:
SsangYong Korando/New Actyon 2.0 G20DF
Price: 200 Eur.
Module Kia/Hyundai Diesel
FID: 37, 42, 41, 39
Module for OBD reflash for ECUs used in diesel

Kia/Hyundai vehicles with Delphi and Denso ECUs.
Kia/Hyundai Denso Diesel SH72546 (FID: 42)

ECU based on MCU Renesas SH72546 with internal
memory 3.75Mb.
Allows to virtual read and write FullFlash via CAN-bus with CHK calculation. Recovery
is possible from any state.
Supported vehicles:
Hyundai Grand Starex H-1 (TQ) 2.5 CRDI Euro6
Hyundai H350 (EU) 2.5 CRDI Euro6
Hyundai H100 Porter (HR) 2.5 CRDI Euro6
Kia Bongo/K2500 2.5 CRDI Euro6
Kia/Hyundai Delphi DCM6.2AP (FID: 41) - test

ECU based on MCU NXP SPC5674 with internal memory 4Mb.
Supported vehicles:
Hyundai i20 (GB) 1.1 CRDI Euro6
Kia Rio (UB) 1.1 CRDI Euro6
Kia/Hyundai Delphi DCM3.7AP (FID: 39)
ECU based on MCU Renesas SH72513 with internal memory 2Mb.
Allows to read FullFlash and write calibration area via CAN-bus with CHK calculation.
Supported vehicles:
Hyundai H-1 (TQ) 2.5 CRDi Euro4/5
Hyundai i20 (PB) 1.1 CRDi Euro5
Hyundai i20 (PB) 1.4 CRDi Euro4/5
Hyundai i30 (GD) 1.4 CRDi Euro5
Hyundai iX20 (JC) 1.4 CRDi Euro5
Hyundai H100/Porter (HR) 2.5 CRDi Euro5
Kia Rio (UB) 1.1 CRDi Euro5
Kia Rio (UB) 1.4 CRDi Euro5
Kia Cee'd (JD) 1.4 Euro5
Kia Venga (YN) 1.4 CRDi Euro5
Kia Bongo/K2500 (PU) 2.5 CRDI Euro5
Kia Delphi DCM3.2AP (FID: 37)

ECU based on MCU Motorola MPC563 +external flash AM29BDD160GB with total
memory adress area 2.5Mb.
Allows to read FullFlash, write with CHK calculation by CAN-bus.
Supported vehicles:
Kia Bongo 2.9 CRDI Euro4
Kia Carnival 2.9 CRDI Euro4
Kia Sedona 2.9 CRDI Euro4
Price: 250 Eur.
Module Kia/Hyundai Petrol CAN
FID: 70, 72, 73, 74, 77, 88, 93, 104
Module for reading and writing through CAN-bus by diagnostic OBD2 plug ECUs used in
petrol Kia and Hyundai vehicles.
Kefico CPEGD2/CPGDSH2 (FID: 70)

Supported Kefico CPEGD2.20.1 and CPGDSH2.26.1 ECUs are based on MCU Infineon
Tricore TC1782 with internal flash memory 2.5Mb.
Allows reading and writing calibration area through CAN-bus with checksum correction.
Recovery is possible from any state.
Bosch ME(G)17.9.1x (FID: 72)

ECU series Bosch ME(G)17.9.11/12/13 is based on MCU Infineon Tricore TC1762 with
internal flash memory 1.46Mb.
Allows reading and writing FullFlash through CAN-bus with checksum correction.
Supported vehicles:
Kia/Hyundai 1.0-1.6 MPI/DOHC
Bosch ME(G)17.9.21 (FID: 74)

ECU series Bosch ME(G)17.9.21 is based on MCU Infineon Tricore TC1724 with internal
flash memory 1.5Mb.
Bosch ME(D)(G)17.9.8 (FID: 73)

ECU series Bosch ME(D)(G)17.9.8 is based on MCU Infineon Tricore TC1767 with
internal flash memory 2.0Mb.
Siemens SIM2K-47 (FID: 88)
ECU Siemens SIM2K-47 is based on MCU С167 with external flash memory 512Kb.
Siemens SIM2K-24x (FID: 93)

ECU series Siemens SIM2K-240/241/242/245 is based on MCU Infineon Tricore TC1764
with internal flash memory 2Mb.
Siemens SIM2K-141/341 (FID: 104)

ECU series Siemens SIM2K-141/341 is based on MCU Motorola MPC561 with external
flash memory 2Mb.
Delphi MT86 (FID: 77)

ECU Delphi MT86 is based on Tricore TC1766 with internal flash memory 1.46Mb.
Allows reading and writing calibration area through CAN-bus with checksum
correction.
Price: 200 Eur.
Module Kia/Hyundai Continental SIM2K-25x/26x
Module for reading and writing in BSL mode for Continental SIM2K-
250/251/253/258/260 ECUs used in petrol Kia and Hyundai vehicles.
Continental SIM2K-25x TC1782 (FID: 150)

ECU series Siemens SIM2K-250/251/253/258 with MCU Infineon Tricore TC1782
onboard have internal flash memory 2.5Mb.
FID allows reading and writing of calibration area in BSL mode. ECU needs to be
opened. Checksum and CVN correction performs on writing.
Continental SIM2K-260 TC1791 (FID: 151)

ECU is based on MCU Infineon Tricore TC1791 onboard have internal flash memory
4Mb.
FID allows reading and writing of calibration area in BSL mode. ECU needs to be
opened. Checksum and CVN correction performs on writing.
Continental SIM2K-250/251 TC1767 (FID: 152) - in development
Attention! Special power adapter BITS001 required. Tested only with J2534 Tactrix
Openport 2.0, DrewTech CarDAQ, Bosch VCM2.
Price: 200 Eur.
Module China Delphi Petrol
FID: 51, 52, 53, 54, 55, 56, 58, 59, 61, 86
Software module for reading and writing Delphi ECUs internal flash memory for China
 Delphi MT20U (FID: 51) with Motorola MC912DT128 128Kb - R/W/CS

 Delphi MT20U2 (FID: 59) with Motorola MC9S12KG256 256Kb - R/W/CS
 Delphi MT22.1 (FID: 52) with Motorola MC9S12XEP768 768Kb - R/W/CS
 Delphi MT22U (FID: 53) with Motorola MC9S12XET256 256Kb - R/W/CS
 Delphi MT20UED (FID: 58) with Motorola MC9S12KG256 256Kb - R/W/CS
 Delphi MT22.1.1 HW1 (FID: 54) with Motorola MC9S12XET256 256Kb - R/W/CS - test
 Delphi MT34 (FID: 55) with Infineon Tricore + EXT.Flash 1Mb - R/W/noCS - test
 Delphi MT62.1 (FID: 56) with NXP SPC5634 1.5Mb - R/W/noCS
 Delphi MT80 (FID: 61) with Infineon Tricore TC1762 1.5Mb - R/W/CS - test
 Delphi MT92 (FID: 86) with Infineon Tricore TC1767 2Mb - R/W/noCS - test
Price: 140 Eur.
Module China Siemens Petrol
FID: 83
Software module for reading and writing Siemens/Continental ECUs internal flash
memory for China vehicles with petrol engines.
Continental Simos 9.5 (FID: 83)

ECU Simos 9.5 is based on MCU C167 with external flash memory 512 Kb. It allows to
virtual read fullflash, write calibration area via CANbus and checksumm correction on
writing.
Price: 100 Eur.
Module China Bosch Petrol
FID: 57, 60, 63, 68, 75, 76, 81, 82, 84
Software module for reading and writing Bosch ECUs internal flash memory for China
 Bosch ME7.9.7 (FID: 68) with C167 1Mb VR/W/CS

 Bosch M7.8 (FID: 57) with ST10F275 832Kb VR/W/CS
 Bosch ME7.8.8 (FID: 63) with ST10F275 832Kb K-line VR/W/CS
 Bosch ME7.8.8 (FID: 76) with ST10F275 832Kb CAN VR/W/CS
 Bosch ME17.8.8 (FID: 60) with Infineon TC1728 1.5Mb R/W/CS
 Bosch ME17.8.8.1 (FID: 82) with Infineon TC1728 1.5Mb R/W/CS
 Bosch ME17.8.8.1 Geely (FID: 84) with Infineon TC1728 1.5Mb R/W/CS
 BYD TB10 (FID: 81) with Renesas SH72531 1.25Mb R/W/CS
 Bosch M7.8/ME7.8.8 BSL (FID: 75) with ST10F275 832Kb K-line R/CS*
* - adapter BITS001 required. Tested only with J2534 Tactrix Openport 2.0
Price: 140 Eur.
Module Volvo Denso SH72xxx CAN
FID: 142, 143
Module for reading and writing on the Bench through CAN-bus for diesel and petrol
Volvo vehicles with Denso SH72xxx ECus.
Removing ECU required but opening not need, only direct CAN connection to ECU.
Volvo Denso SH72543 2Mb BENCH-CAN (FID: 143)

Volvo Denso SH72546 3.75Mb BENCH-CAN (FID: 142)
Module supports FullFlash reading and writing and CS fix on writing.
Price: 200 Eur.
Module GM Diesel CAN
FID: 65, 67, 85, 90
Module for reading and writing through OBD2 connector by CAN-bus ECUs used in
diesel GM vehicles (Opel, Chevrolet, Saab, Holden).
GM Bosch EDC16C39 HW1 (FID: 65)

ECU is based on MCU Motorola MPC562 with external flash memory 2.0Mb.
Allows to read and write calibration area through CAN-bus with checksumm correction
on writing.
Supported vehicles:
Chevrolet Captiva 2.0 VCDI
Chevrolet Cruze 2.0 VDCI
Chevrolet Epica 2.0 VCDI
Chevrolet Lacetti 2.0 VCDI
Daewoo Winstorm 2.0 VCDI
Opel Antara 2.0 CDTI
Opel Astra (H) 1.9 CDTI
Opel Combo (D) 1.6 CDTI
Opel Signum 1.9 CDTI
Opel Vectra (C) 1.9 CDTI
Opel Zafira (B) 1.9 CDTI
GM Bosch EDC16C39 HW2 (FID: 67) - Bench OBD only

Allows to read and write calibration area through CAN-bus on the bench with
checksumm correction on writing.
Supported vehicles:
Chevrolet Trailblazer II 2.8TD Duramax
Holden Colorado 2.8TD Duramax
GM ACDelco E87 (FID: 90)
ECU is based on MCU Motorola MPC5565 with internal flash memory 2.0Mb.

ECU is based on MCU Motorola SPC5674 with internal flash memory 4.0Mb.
Price: 200 Eur.
Module GM ACDelco Petrol Gen1 CAN
FID: 91, 94, 96, 97, 98, 99, 100
Module for reading and writing through OBD2 connector by CAN-bus ACDelco Gen1
ECUs used in petrol GM vehicles.

Allows to read fullflash and write calibration area through CAN-bus with checksumm
Reading/writing time about 3-5 minutes!

GM ACDelco E39A (FID: 97)



ECU is based on MCU NXP SPC5674 with internal flash memory 4.0Mb.
New ECU type will be added as soon as possible!
Price: 350 Eur.
Module VAG Marelli Petrol
FID: 5, 7
Module for reading and writing Magneti Marelli

ECUs, used on the VAG normal aspirated vehicles
with 1.6 CFNA, CFNB, CLRA, CLSA, 1.4 CGGB,
CLPA, CLPB and 1.6 CFZA engines.
Magneti Marelli IAW 7GV (FID: 5)

This ECU is based on MCU Infineon SAK-XC2785X-104F80L with internal flash memory
832Kb.
Allows to read FullFlash and write calibration area by OBD2. Supports 1.6 CFNA, CFNB,
CLRA, CLSA and 1.4 CGGB, CLPA, CLPB engines.
It writes calibration area and takes only 3 minutes.
Also we are recommend calibration Editor for Marelli IAW 7GV.
Magneti Marelli IAW 7GVE (FID: 71)

This ECU is based on MCU Infineon SAK-XC2xxx with internal flash memory 832Kb.
Allows to read FullFlash and write calibration area by OBD2.
Supports 1.4 CGGB engines.
Magneti Marelli IAW 9GV (FID: 7)

This ECU is based on MCU NXP SPC5634 with internal flash memory 1.5 Mb.
Used in FlexFuel VAG vehicles with 1.6 CFZA engine.
Allows to read and write FullFlash in BSL mode, checksumm correction and EEPROM
reading and writing.
ECU must be opened and connected on the bench as shown in instruction manual.
Attention! Marelli 9GV is not working now with all J2534 adapters. Currently we tested
and guarantee correct work with CarDAQ Plus, Bosch VCM2, Mongoose.
Also we are recommend calibration Editor for Marelli IAW 9GV.
Magneti Marelli IAW 4HV (FID: 17)

This ECU type is using on VAG vehicles with 1.4 BUD, BXW, CGGA, CGGB petrol engines.
Allows to read FullFlash and write of calibration area by K-Line.
ECU is based on MCU ST10F296 with internal adress space 832 Kb.
Price: 100 Eur.
Module PSA Diesel CAN
FID: 179, 210, 211
Module for reflashing through OBD2 connector by CAN-bus Delphi ECUs used in
Peugeot and Citroen deisel vehicles.
PSA Delphi DCM6.2A (FID: 179)

This ECU is based on MCU NXP MPC5674 with internal flash memory 4.0 Mb. Allows
reading and writing of calibration area by OBD2 with checksumm correction on
writing.
PSA Bosch EDC17C10 TC1797 (FID: 210)

ECU is based on MCU Infineon Tricore TC1797 with internal flash memory 4.0 Mb.
Allows reading and writing of calibration area by OBD2 with checksumm correction on
writing.
PSA Bosch EDC17C10 TC1796 (FID: 211)

ECU is based on MCU Infineon Tricore TC1796 with external flash memory 4.0 Mb.
Allows reading and writing of calibration area by OBD2 with checksumm correction on
writing.
Price: 200 Eur.
Module Trucks/Industrial Bosch EDC17CV41
FID: 109, 110, 112, 113, 114, 115, 116, 119
Module for reading and writing through OBD2 connector by CAN-bus Bosch EDC17CV41
ECUs used in trucks/industrial vehicles Tata-Daewoo, New Holland, CASE, CLAAS, Iveco,
Doosan.
ECU is based on MCU Infineon Tricore TC1797 with internal flash memory 4.0Mb.
on writing.
 Iveco Bosch EDC17CV41 (FID: 110)

 Tata-Daewoo Bosch EDC17CV41 (FID: 112)
 CASE/New Holland Bosch EDC17CV41 (FID: 113)
 CLAAS Bosch EDC17CV41 (FID: 114)
 Doosan Bosch EDC17CV41 (FID: 115)
 Tigercat Bosch EDC17CV41 (FID: 116)
 Pi Makina Bosch EDC17CV41 (FID: 119)
 Ford Bosch EDC17CV41 (FID: 109)
Attention! Some of supported vehicles are using 24V voltage onboard. Please use J2534
adapters with 24V support or connect ECU on the bench.
New ECU types will be added as soon as possible!
Price: 400 Eur.
Module Trucks Delphi DMCI CAN
FID: 117, 118
Module for reading and writing by CAN-bus Delphi DMCI ECUs used in DAF and
Hyundai trucks.
on writing.
 DAF Delphi DMCI (FID: 117)

 Hyundai Delphi DMCI (FID: 118)
Price: 300 Eur.
Module Delphi MT05
FID: 1, 2
SW module to flash ECUs Delphi MT05 and

Delphi MT05.2/3 through the diagnostic
connector. It allows identification, read
FullFlash and write the calibration area, as
well as automatic correction checksums
while writing.
J2534 adapter needed (i.e. Tactrix Openport 2.0 ).
Delphi MT05 (FID:2) is based on the MCU Infineon SAK-XC164CM-16F40F with internal
flash memory 128Kb.
Delphi MT05.2/3 (FID:1) is based on the MCU Infineon SAK-XC164CS-32F40BB with
internal flash memory 256Kb.
Price: 250 Eur.
Module China Bosch Moto/Extreme
FID: 6, 78, 79
Software module to work through the diagnostic

connector with Bosch MSE3.0 and US6.0 engine
control units. Allows you to identify the software
version, to virtual read files from our server and
to write calibration area with automatic
correction checksums on writing.
Work can be performed via the diagnostic connector of the vehicle or by connecting
directly to the ECU connector on the bench .
Bosch MSE3.0 (FID: 6, 78)

ECU is based on MCU ST10F275 with internal memory area 832Kb. Allows Virtual
Reading and Writing with CS fixing. If we have no file on server it is possible to read in
BSL mode with FID:78.
Bosch MSE6.0/US6.0 (FID: 79)

ECU is based on MCU SPC563M64 with internal memory area 1.5Mb. Allows Virtual
Reading and Writing with CS fixing. If we have no file on server u have to send ECU to
our office for reading and adding to server.
Price: 250 Eur.
Module Rotax Extreme
FID: 10, 11, 31
Module for reading and writing extrime vehicles with

Rotax engines and ECUs Bosch ME17.8.5 and Siemens
MSE 3.7x. Its working through diagnostic plug or on the
bench with no need to open ECU.
Siemens MSE 3.7x (FID: 10, 80)

Siemens MSE 3.7x family allows to get software ID, read FullFlash and write calibration
area by K-line (FID 10) and CANbus (FID 80), also it performes checksum correction on
writing.
For today we support 2 ECU types:
 Siemens MSE 3.7 with MCU ST10F269 and internal Flash memory 256Kb.
 Siemens MSE 3.71 with MCU ST10F269 and internal Flash memory 256Kb.
Bosch ME17.8.5 (FID: 11, 31)

Allows to get software ID, virtual reading of the FullFlash from our server and to write
calibration area by CANbus. Also it performs checksum correction on writing.
We will not respond to the claims about the inability to read a file from our server
(Virtual reading) if we do not have it.
ECU is based on MCU Infineon Tricore TC1762 with internal Flash memory 1504Kb.
Price: 250 Eur.
Module Harley-Davidson Delphi
FID: 30, 43
Module for OBD reading and writing Harley-Davidson

motorbikes with Delphi ECUs.
HD Delphi MT05 CAN (FID:30) is based on the MCU

NXP MC9S12XEP768 with internal flash memory
768Kb.
HD Delphi VooDoo CAN (FID:43) is based on the MCU
NXP MC9S12DG128 with internal flash memory 128Kb.
Price: 200 Eur.
Module Moto/Extreme Denso Virtual Reader
FID: 64, 103
Service module for identification and virtual reading of

Arctic Cat and Suzuki Denso ECUs 32920-4xxxx based
on MCU Renesas SH7052.
Real ECU software reading is only possible with drilling big hole to access AUD port
pins. Its not very safe for future outdoor ECU using.
This module allows to get correct file with no drilling.
You can get software ID through K-line and get file if we have it on our server.
 Arctic Cat Denso Virtual Reader (FID: 64)

 Suzuki Moto Denso Virtual Reader (FID: 103)
Attention! We are not provide ORI files by mail, skype etc. You have to use this module
to get file with the vehicle.
Attention! Module does not provide writing.
do not have it.
Attention! Module activated for FREE for all users of BitEdit Arctic Cat Denso module
Price: 100 Eur.
Module MV Agusta Eldor
Module for software identification (ID), virtual reading and writing Eldor EM 2.0 ECUs
used in motobikes MV Agusta.
ECU is based on MCU NXP MPC5634 with internal flash memory 1.5Mb.
Supported models:
 Brutale
 F3
 F4
 Rivale
 Turismo Veloce
Price: 100 Eur.
Module BMW Motorrad
FID: 170, 171, 172
Module for OBD reading and writing BMW Motorrad motorbikes with Bosch and
Magneti Marelli ECUs.
Bosch M9.2 (BMSK) (FID: 171)

Bosch ME9.2.0 (BMSKP) (FID: 172)
Marelli MBC1 (BMS-E) (FID: 170)
Bosch ME17.2 (BMS-X) - in development
Marelli MBC2 (BMS-E2B) - in development
Price: TEST.
Module BitBox Slave initial
We are glad to inform you, that today the Master/Slave system is ready to open testing
for our customers and from now Slave version is available to purchase. We have
successfully finished internal testing in which several our customers participated!
What is it?
If you have several branches or regular customers to whom you are doing mod files,
and they are interested in our product – they can receive all modules which you have,
but they will have no access to your files, and you keep a secret of your developments.
They also as well as you will have an opportunity to read and write files, but only you
will be able to see them and that, much important, the file will be only written with
your permission. Also, you will know when the file has been written, and when there is
no.
How it works?
You can attach infinite number of Slave keys to your Master (now regular) key:
 You are purchasing Slave key and attach it to you Master key.
 Slave runs applications, connecting to the vehicle and reads the file as usual. At the
end of reading it will be offered to send a request for calibration to the Master - to you,
he fills the form shown in the screenshot.
 You will see his request in Master files window. You can save original file, and upload
modified or original file to your Slave for writing.
 After that Slave press Write and select the file from your files, prepared for him and
after successful writing file will be marked as USED.
 Slave can’t use one file more than once!
Actually, file transfer does not happen between you and Slave. All files are stored in the
protected storage, and access to it provides only your Master key! You do not transfer
files each other and also precisely know that Slave already used the file!
How much it costs?

One Slave dongle costs 50 EUR and 200 EUR for the first license activation with 1 year
free usage (subscription). After 1 year usage each next year costs 200 EUR.
Slave have access to all Master purchased modules and there is no reason to buy any
new module to each slave. All purchased families available for ALL Slave dongles!
What does ‘open testing’ means?

To bring the system to complete state, we need real testing on real customers and
vehicles. Then will be able to make the system more useful and easy for you. In return
for this, for the period of testing you get a free period of use. In other words, when the
open testing period ends, all subscription terms will be discarded and you will receive a
whole year of use from the end of the testing period.
Price: 250 Eur.
USB security dongle
Security dongle - this is device that connects through USB port and makes the
identification of the user and activated licenses. It is necessary part of our software and
buying once and for all/any software module.
We are currently using the most modern and small version of the key SenseLock EL-
Genii with built-in internal memory of 64 KB.
Dongle is selling only with one or more modules of the BitEdit or BitBox software.
Dongle price 30 Eur.
Adapter CF Moto 3pin-to-OBD2
Adapter CF Moto 3pin-to-OBD2 adapter is designed to connect OpenPort 2.0 or any

device with built-in OBD2 Male to the diagnostic connector of CF Moto vehicles.
It allows to perform reflash vehicles with Bosch MSE3.0 and Delphi MT05.2 ECUs with
no need to get ECU on the bench.
Price: 50 Eur.
Adapter 6pin-to-OBD2
Adapter 6pin-to-OBD2 adapter is designed to connect J2534

adapter or any device with built-in OBD2 Male to 6-pin diagnostic connector of different
extreme vehicles like ATVs, UTVs and motorcycles made in China.
Price: 50 Eur.
Adapter BRP 6pin-to-OBD2
Adapter BRP 6pin-to-OBD2 is designed to connect OpenPort 2.0 or any device with
built-in OBD2 Male to the diagnostic connector of BRP vehicles.
Can be used for most 4-TEC/E-TEC models of BRP vehicles 2004-2016.
Price: 50 Eur.
Adapter HD 6pin-to-OBD2
Adapter BRP 6pin-to-OBD2 is designed to connect OpenPort 2.0 or any device with
built-in OBD2 Male to the diagnostic connector of Harley-Davidson vehicles.
This adapter is for using with BitBox Harley-Davidson Delphi module.
Price: 50 Eur.
Power adapter BITS001
Special power adapter BITS001 bench ECU connection.
Performs automatic power and boot-pin managment.*
This adapter is mandatory to use for reading Bosch M7.8/ME7.8.8 and working with
Continental SIM2K-25x/26x ECUs in BSL mode.
* - tested and work with garantee with Tactrix OpenPort 2.0
Price: 60 Eur.
Adapter BMW 10pin-to-OBD2
Adapter BMW 10pin-to-OBD2 is designed to connect J2534 adapter or any device with
built-in OBD2 Male to the diagnostic connector of BMW Motorrad vehicles.
Price: 50 Eur.

Car List
For download car list please scan QRCode.
+98 51 38 64 41 19 info@Carsoft‐Tech.com
+98 912 067 6004 www.Carsoft‐Tech.com

Bit Box

Uploaded by

Copyright:

Available Formats

Bit Box

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Bit Box

Uploaded by

Copyright:

Available Formats

What vehicles and ECUs are supported according to the documentation?

What vehicles and ECUs are supported according to the documentation?

What products and services are offered?

What products and services are offered?

Price for BitBox

Name Description Price, Eur.

Toyota Denso NEC 76F00XX (FID: 24)

Price: 250 Eur.

FID: 23, 27, 28

Module for OBD reading/virtual reading and

Module supports 2 protocols types:

TYPE 1 (FID: 23, 27)

Supported vehicles: Supported engines:

TYPE 2 (FID: 28)

 Engine MCU D76F0199GD 1280Kb

Supported vehicles: Supported engines:

Price: 250 Eur.

Toyota Denso Gen3 R7F701202 (FID: 149)

Supported vehicles: Supported engines:

Price: 250 Eur.

Toyota Delphi MPC565/SH72xx (FID: 140)

Supported filesize: 1Mb, 1.5Mb, 2Mb

Price: 100 Eur.

Service module for identification and virtual

Toyota Gen1 ECM Virtual reader (FID: 8)

Our base is now contains 4000+ files.

Price: 120 Eur.

Package of 5 modules with discount for Toyota/Lexus/Scion/Hino vehicles.

Price: 850 Eur.

Module for reading and writing via diagnostic

Bosch GS8.60.2 (FID: 3)

Price: 100 Eur.

FID: 46, 47, 48, 49, 50, 135, 136, 137

Allows VIRTUAL reading and writing of calibration area.

Module is now supports:

 Bosch EDC17CP45 (DDE7.3.1)

Other ECU types will be added as soon as possible.

FID: 130, 132, 133

• Bosch EDC17C41 (DDE7.2.1)

Supported petrol ECUs:

Price: 350 Eur.

FID: 160, 161

Module for reflashing through OBD2 connector

BMW Fxx/Gxx Bosch MG1 MPC5777 ENET (FID: 160)

Price: 350 Eur.

Price: 900 Eur.

FID: 200, 201, 202

Supported ECU types:

Price: 250 Eur.

FID: 203, 204, 205, 208

Supported ECU types:

Price: 250 Eur.

Continental SIM271DE2.0 (FID: 209)

Siemens SIM271KE2.0 (FID: 213)

Price: 200 Eur.

FID: 12, 13, 14, 15, 16, 17

Module for reading and writing through the

Also its possible to work on the bench with no