RT9130E-2

Product Guide
ANSI B30.5
Imperial 85%

Features
• 120 t (130 USt) capacity • Grove MEGAFORM™ boom
• 12,8 m - 48,8 m (42 ft - 160 ft) five-section, full • Cummins 239 kW (320 hp) Tier 4F, diesel
power boom engine
• 11 m -18 m (36 ft - 59 ft) offsettable bi-fold
swingaway extension
• 8 m (26 ft) extension inserts
GROVE RT9130E-2

The RT9130E-2 has an impressive 130 USt capacity and

a Full Vision cab to keep the operator comfortable and
maximize productivity with the ergonomically-
designed controls..

Features
Boom
The 48,8 m (160 ft) five-section Full Power boom
incorporates the “U” shaped MEGAFORM™ design,
which eliminates stiffeners, thus reducing weight and
increasing capacity.

Extensions
A 18 m (59 ft) offsettable bi-fold lattice swingaway extension
and two 8 m (26 ft) inserts give the RT9130E-2 a maximum
tip height of 85 m (279 ft). A hydraulically offsettable bi-fold
lattice swingaway is also available, and conveniently offsets
from 0˚ to 40˚ from the operator’s cab.

Cab
The Full Vision cab on the RT9130E-2 tilts up to 20˚
providing the operator additional comfort when working
at long boom and extension lengths.

Removable outrigger boxes

Removable front and rear outrigger boxes provide up
to 8788 kg (19,374 lb) of weight reduction for easier
transport. Includes the removable 18 100 kg (40,000 lb) of
counterweight, auxiliary hoist and rope, and can easily self-
remove close to 29 000 kg (64,000 lb).

CraneSTAR is an exclusive and innovative

crane asset management system
that helps improve your profitability and reduce costs
by remotely monitoring critical crane data.
Visit www.cranestar.com for more information.
RT9130E-2 benefits
Competitive capacities and impressive working range
ensures maximum utilization and profitability.

Full power boom allows for telescoping loads if needed.

Eliminates excessive time lost pinning and unpinning
competitive models pinned boom design.

Tilt cab, suspension seat, and ergonomically positioned

controls supply the operator with a full day comfortable
working environment and less fatigue at shift end.

Counterweight and both outrigger boxes are hydraulically

self-removable and installed by the crane.

Full proportional single axis hydraulic controls provide

finger tip control for precise positioning of any load at
any boom length or load radius.

Powerful engine, powershift transmission, 4 wheel drive

and 4 wheel steer, and the ability to move with boom
extension and inserts installed provides outstanding job-
site maneuverability with no time loss.

Manitowoc Crane Care when you need it. Manitowoc Finance helps you get right to
The assurance of the world’s most advanced crane work generating profits for your business.
service and support to get you back to work fast. Financial tools that help you capitalize on
opportunity with solutions that fit your needs.
Contents

Dimensions ..................................................................................................................................................................... 5

Weights .......................................................................................................................................................................... 6

Working range................................................................................................................................................................. 7

Load charts ..................................................................................................................................................................... 8

Working range with inserts............................................................................................................................................... 11

Load charts with inserts ................................................................................................................................................. 12

Working ranges - luffing extension.................................................................................................................................... 14

Load charts - luffing extension ......................................................................................................................................... 16

Load handling ................................................................................................................................................................. 23

Specifications................................................................................................................................................................... 24

Symbols glossary.............................................................................................................................................................. 26
 Dimensions

Tire Size: 33.25 x 29

A B C D E F G A B C D E F G

18 237 mm 18 847 mm 15 748 mm 14 884 mm 14 453 mm 11 709 mm 10 236 mm 13 970 mm 14 453 mm 10 973 mm 10 135 mm 9652 mm 6909 mm 5918 mm
(717.9”) (742.0”) (620.0”) (585.9”) (569.9”) (460.9”) (402.9”) (550.0”) (569.0”) (432.0”) (399.0”) (380.0”) (272.0”) (232.9”)

Two-Wheel Steer Four -Wheel Steer

All dimensions are in mm (in).

Full 8484 mm (334.0")

Mid 6020 mm (237.0")
Ret 3556 mm (140.0")
3626 mm
A (142.8")
3797 mm fender
(149.5") width
C D E
Outside Turn
curb radius G
F 24° R 4368 mm
radius Inside 16°
Inside turn (R 171.9")
curb radius
584 mm (22.9")

radius
Tail swing
12 805 mm (504.1 ")
259 mm (10.2")
C Rotation
L

4179 mm
(164.5")

2614 mm
(102.9")

20° 17°
555 mm
427 mm
(21.9")
(16.8")

2337 mm (92.0")
568 mm (22.3")

4423 mm (174.1") 4429 mm (174.3")

4940 mm (194.5")
5895 mm (232.1") 9754 mm (384.0")

Grove RT9130E-2 5
 Weights

Weights
Gross Front Rear
kg lb kg lb kg lb
Basic Machine: (T4F) including 72,5m (160 ft) main boom, main
hoist with (431m 950 ft) of rope,auxiliary hoist with 318 m (700 ft) of
wire rope, 18 144 kg (40,000 lb) counterweight,11 m - 18 m (36 ft - 59 79 913 176,175 36 333 80,100 43 580 96,075
ft) manual extension, 9 t 10 USt) headache ball, and 72,5 t (80 USt)
hook block:
Remove: 18 144 kg (40,000 lb) counterweight and auxiliary hoist and
-19 997 - 44,084 5714 12,597 -25 711 -56,681
wire rope
crane weight: 59 916 132,091 42 047 92,697 17 869 39,394

Remove: 11 m - 18m (36 ft - 59 ft) manual extension -1411 -3110 -2141 -4721 731 1611

crane weight: 58 506 128,981 39 906 87,976 18 600 41,005

Remove: 72,5 t (80 USt) hook block -730 -1610 -694 -1531 -36 -79

crane weight: 57 775 127,371 39 211 86,445 18 564 40,926

Remove: 9,0 t (10 USt) headache ball -330 -727 -526 -1159 196 432

crane weight: 57 446 126,644 38 686 85,286 18 760 41,358

Remove: Front outrigger box and beam -4276 -9427 -5848 -12,892 1572 3465

crane weight: 53 170 117,217 32 838 72,394 20 332 44,823

Remove: Rear outrigger box and beam -4276 -9427 1803 3974 -6079 -13,401

crane weight: 48 894 107,790 34 641 76,368 14 253 31,422

Remove: (4) tire / wheel assemblies -4318 -9520 -2159 -4760 -2159 -4760

crane weight: 44 575 98,270 32 481 71,608 12 094 26,662

Remove: Main boom assembly, auxiliary boom nose, and extension
-15 361 -33,865 -20 631 -45,483 5270 11,618
brackets
crane weight: 29 214 64,405 11 850 26,125 17 364 38,280

THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE.
6 The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane
 Working range

160 ft main boom + 36 ft - 59 ft fixed offset extension

240
0° OFFSET
230 59' EXT.
20° OFFSET

220
40° OFFSET

210 36" EXT.

200

190

180
160
170 70°

160 60° 145

150

Boom and extension length in feet

Height from the ground in feet

130
140 50°

130 115

120 40°
100
110

100 86
30°

90
72
80

70 20° 57

60
42
50

10° 78° MAX

40
BOOM ANGLE
30

20

0°
10

200 190 180 170 160 150 140 130 120 110 100 90 80 70 60 50 40 30 20 10 AXIS OF ROTATION

Operating radius in feet from axis of rotation

9' - 8"
Dimensions are for largest Grove furnished hookblock
11' - 0"
and headache ball, with anti-two block activated.

THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE.
Grove RT9130E-2 The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane 7
 Load chart

42 ft - 160 ft 40,000 lb 100% 360°

27 ft 10 in
spread
Pounds
Feet
Main boom length in feet
42 57 72 86 100 115 130 145 160
+260,000 147,000
10 (71.5) (76.5)
224,000 147,000 *127,000
12 (68.5) (74.5) (78)
176,000 147,000 127,000 *92,600
15 (63.5) (71.5) (76) (78)
20 127,500 125,500 115,500 86,550 *65,000
(55.5) (65.5) (71.5) (75.5) (78)
25 97,300 95,550 95,300 78,900 62,650 44,600
(46) (60) (67) (72) (75) (78)
30 76,900 75,250 75,050 68,500 56,800 44,600 43,150
(34) (53.5) (62.5) (68.5) (72) (75.5) (78)
35 60,950 60,750 60,100 50,050 44,600 42,200 32,550
(46.5) (58) (64.5) (69) (73) (76) (78)
40 50,300 50,150 50,550 44,050 41,400 38,000 32,550 25,100
(38.5) (52.5) (60.5) (66) (70) (73.5) (76) (78)
45 42,050 41,950 42,350 38,950 37,450 34,150 32,550 24,800
(28) (47) (56.5) (62.5) (67.5) (71) (74) (76.5)
50 35,400 35,850 34,650 33,450 31,350 29,550 24,500
(41) (52.5) (59) (64.5) (68.5) (71.5) (74.5)
55 30,050 30,550 30,050 30,000 29,200 26,850 24,000
(34) (47.5) (55.5) (61.5) (66) (69.5) (72.5)
25,600 26,100 25,850 26,950 26,350 24,700 23,200
60 (24.5) (42.5) (58.5) (63.5) (67.5) (70.5)
(52)
65 22,400 22,150 23,800 23,850 22,950 21,100
(37) (48) (55.5) (61) (65) (68.5)
19,200 18,950 20,800 21,600 20,850 19,200
70 (30.5) (52.5) (58.5) (62.5) (66.5)
(44)
75 16,400 16,200 18,100 19,250 19,000 17,500
(22) (39) (49) (55.5) (60.5) (64.5)
80 13,800 15,700 16,900 17,100 15,750
(34) (45.5) (52.5) (58) (62.5)
85 11,650 13,550 15,000 15,500 14,300
(28) (41.5) (49.5) (55.5) (60)
90 9770 11,700 13,100 13,900 13,100
(19.5) (37) (46.5) (53) (58)
95 10,000 11,450 12,250 12,150
(32) (43) (50) (55.5)
100 8490 9940 11,000 11,400
(26.5) (39.5) (47) (53)
105 5690 8630 9730 10,200
(18.5) (35.5) (44) (50.5)
110 7320 8460 9020
(30.5) (41) (48)
6220 7370 8100
115 (25) (37.5) (45.5)
120 5120 6280 7190
(17.5) (33.5) (42.5)
5350 6270
125 (29.5) (39.5)
130 4430 5350
(24) (36)
2560 4560
135 (16.5) (32.5)
140 3770
(28)
Minimum boom angle (°) for indicated length (no load) 23
Maximum boom length (ft) at 0° boom angle (no load) 145
*This capacity is based on maximum obtainable boom angle.
+16 parts line required to lift this capacity (using aux. boom nose). Refer to Operator’s and Safety Handbook for reeving diagram.
NOTE: () Boom angles are in degrees

Lifting capacities at zero degree boom angle

Boom Main boom length in feet
Angle 42 57 72 86 100 115 130 145 160
41,400 24,650 15,350 9700 5250 3650 2450 1450
0° (35.3) (50) (64.6) (79.3) (94) (108.6) (123.3) (138)
Note: ( ) Reference radii in feet . A6-829-103576

THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE.
8 The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane
 Load chart

NOTES:
130 ft 36 ft - 59 ft 40,000 lb 100% 360°
1. All capacities above the bold line are based
27 ft 10 in on structural strength of boom extension
spread and do not exceed 85% of tipping loads, in
Pounds accordance with SAE J-765.
Feet
2. 36 ft boom extension may be used for single
36 ft LENGTH 59 ft LENGTH or double line lifting service. 59 ft boom
0° 20° 40° 0° 20° 40° extension may be used for single line lifting
OFFSET OFFSET OFFSET OFFSET OFFSET OFFSET service only.
WARNING: Lifting with the 36 ft extension
23,350
35 (78) base, with the 23 ft extension fly either
23,350 12,300 erected or folded along side of extension base,
40 (77) (78) is strictly prohibited.
23,350 *21,300 12,300 3. Radii listed are for a fully extended boom with
45 (75) (78) (77.5)
the boom extension erected. For main boom
23,350 20,700 12,300
50 (73.5) (76.5) (76) lengths less than fully extended, the rated
23,350 20,100 16,600 12,300 loads are determined by boom angle. Use
55 (71.5) (75) (78) (74.5) only the column which corresponds to the
23,350 19,500 16,350 12,300 11,600 boom extension length and offset for which
60 (69.5) (73) (76) (73) (78)
22,300 19,000 16,100 12,300 11,300
the machine is configured. For boom angles
65 (67.5) (71) (74) (71.5) (77) not shown, use the rating of the next lower
20,350 18,500 15,850 12,300 10,950 boom angle.
70 (66) (69) (72) (69.5) (75) WARNING: Operation of this machine with
18,350 18,050 15,650 12,300 10,700 8940 heavier loads than the capacities listed is
75 (64) (67) (70) (68) (73.5) (78)
16,600 17,100 15,500 12,300 10,400 8790 strictly prohibited. Machine tipping with
80 (62) (65) (68) (66.5) (72) (76) boom extension occurs rapidly and without
85
15,050 15,550 15,300 12,300 10,150 8650 advance warning.
(60) (63) (66) (64.5) (70) (74.5) 4. Boom angle is the angle above or below
13,700 14,150 14,500 12,300 9910 8520
90 (57.5) (61) (63.5) (63) (68.5) (72.5)
horizontal of the longitudinal axis of the
12,450 12,900 13,250 11,900 9680 8410 boom base section after lifting rated load.
95 (55.5) (58.5) (61.5) (61) (66.5) (70.5) 5. Capacities listed are with outriggers properly
100
11,300 11,750 12,100 11,450 9460 8300 extended and vertical jacks set only.
(53.5) (56.5) (59) (59) (64.5) (68.5)
105 10,300 10,750 11,050 10,500 9260 8210
(51) (54) (56.5) (57.5) (63) (66.5)
9390 9810 10,050 9580 9060 8120
110 (48.5) (52) (54) (55.5) (61) (64.5)
115 8570 8970 9200 8790 8860 8050
(46) (49.5) (51.5) (53.5) (59) (62.5)
120 7750 8140 8350 8010 8660 7990
(43.5) (46.5) (48.5) (51.5) (57) (60.5)
125 6840 7360 7600 7340 7960 7820
(41) (44) (45.5) (49.5) (54.5) (58)
130 5940 6590 6850 6680 7270 7660
(38) (41) (42.5) (47.5) (52.5) (55.5)
135 5170 5730 6100 6660 7010
(34.5) (37.5) (45) (50.5) (53.5)
140 4400 4880 5530 6050 6360
(31) (34) (42.5) (48) (50.5)
145 3730 4120 4890 5510 5770
(27.5) (30) (40) (45.5) (48)
150 3070 3360 4260 4970 5190
(22.5) (25.5) (37.5) (42.5) (45)
155 3670 4360
(35) (40)
160 3090 3750
(31.5) (36.5)
165 2570 3120
(28.5) (33)
170 2060 2490
(24.5) (29)
Min. boom
angle for
indicated 20° 20° 40° 20° 20° 40°
length
(no load)

Max. boom 100 ft 100 ft

length (ft) at
0° boom angle
(no load) A6-829-102127

NOTE: () Boom angles are in degrees

*This capacity is based on maximum obtainable boom angle.

THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE.
Grove RT9130E-2 The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane 9
 Load chart

NOTES:
1. All capacities above the bold line are based
160 ft 36 ft - 59 ft 40,000 lb 100% 360°
27 ft 10 in
on structural strength of boom extension
spread and do not exceed 85% of tipping loads, in
accordance with SAE J-765.
Pounds 2. 36 ft boom extension may be used for single
Feet 36 ft LENGTH 59 ft LENGTH or double line lifting service. 59 ft boom
extension may be used for single line lifting
0° 20° 40° 0° 20° 40°
OFFSET OFFSET OFFSET OFFSET OFFSET OFFSET service only.
WARNING: Lifting with the 36 ft extension
45 16,000 base, with the 23 ft extension fly either
(78)
erected or folded along side of extension
16,000
50 (77.5) base, is strictly prohibited.
15,900 10,100 3. Radii listed are for a fully extended boom with
55 (76) (78) the boom extension erected. For main boom
60 15,850 15,700 10,100 lengths less than fully extended, the rated
(74) (77.5) (77)
loads are determined by boom angle. Use
65 15,800 15,700 *15,200 10,100
(72.5) (76) (78) (75.5) only the column which corresponds to the
15,750 15,000 14,750 10,100 10,050 boom extension length and offset for which
70 (71) (74.5) (77) (74) (78) the machine is configured. For boom angles
14,950 14,300 14,100 10,100 10,050 not shown, use the rating of the next lower
75 (69.5) (73) (75.5) (73) (77.5)
14,200 13,600 13,450 10,100 10,050
boom angle.
80 (68) (71) (74) (71.5) (76) WARNING: Operation of this machine with
85
13,450 12,950 12,850 10,100 10,050 8600 heavier loads than the capacities listed is
(66) (69.5) (72) (70) (74.5) (78) strictly prohibited. Machine tipping with
12,800 12,350 12,250 10,100 9870 8500 boom extension occurs rapidly and without
90 (64.5) (68) (70.5) (68.5) (73) (77.5)
11,700 11,750 11,700 10,100 9680 8400
advance warning.
95 (63) (66) (68.5) (67) (72) (75.5) 4. Boom angle is the angle above or below
100
10,650 11,200 11,200 9710 9450 8310 horizontal of the longitudinal axis of the
(61) (64.5) (67) (65.5) (70) (74) boom base section after lifting rated load.
9710 10,250 10,400 9280 9050 8220 5. Capacities listed are with outriggers properly
105 (59.5) (62.5) (65) (64) (68.5) (72.5)
8780 9310 9680 8850 8650 8140 extended and vertical jacks set only.
110 (57.5) (61) (63) (62.5) (67) (71)
115 7990 8500 8840 8110 8280 7920
(55.5) (59) (61) (61) (65.5) (69.5)
120 7210 7690 8010 7370 7920 7700
(53.5) (57) (59) (59.5) (64) (67.5)
125 6540 7000 7290 6720 7360 7440
(52) (55) (57) (57.5) (62.5) (66)
130 5880 6310 6580 6070 6810 7190
(49.5) (53) (55) (56) (60.5) (64)
135 5300 5710 5950 5510 6210 6630
(47.5) (51) (53) (54.5) (59) (62.5)
140 4730 5110 5330 4950 5620 6080
(45.5) (49) (50.5) (52.5) (57) (60.5)
145 4190 4580 4770 4460 5100 5520
(43) (46.5) (48) (50.5) (55.5) (58.5)
150 3650 4060 4220 3980 4580 4970
(41) (44) (45.5) (49) (53.5) (56.5)
155 3070 3500 3660 3550 4120 4470
(38.5) (41.5) (43) (47) (51.5) (54.5)
160 2490 2940 3130 3660 3970
(35.5) (38.5) (45) (49.5) (52)
165 1970 2370 2710 3240 3510
(32.5) (36) (43) (47.5) (50)
170 1460 1800 2300 2830 3060
(29.5) (32.5) (40.5) (45) (47.5)
1840 2420 2640
175 (38.5) (43) (45)
1390 2010 2220
180 (36) (40) (42)
1530
185 (37.5)
Min. boom 26 28 40 34 35 40
angle for
indicated
length (no load)
Max. boom
length (ft) at
0° boom angle 100 100
(no load)

NOTE: () Boom angles are in degrees A6-829-101980A

*This capacity is based on maximum obtainable boom angle.

THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE.
10 The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane
 Working range

160 ft main boom + 2 inserts + 36 ft - 59 ft fixed offset extension

290
0° 59' EXT.
280 20°

270 40°

260

250

240

230

220

210

200

190

180

Boom and extension length in feet

160
170 70°
Height from the ground in feet

160 60° 145

150
130
140 50°

130 115

120 40°
100
110

100 86
30°
90
72
80

70 20° 57

60
42
50

40 10° 78° MAX

BOOM ANGLE
30

20
0°
10

250 240 230 220 210 200 190 180 170 160 150 140 130 120 110 100 90 80 70 60 50 40 30 20 10 Axis of
Rotation
Operating radius in feet from axis of rotation

9' - 8"
11' - 0" Dimensions are for largest Grove furnished hook block
and headache ball, with anti-two block activated.

THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE.
Grove RT9130E-2 The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane 11
 Load chart

NOTES:
1. All capacities above the bold line are based
160 ft 59 ft 26 ft or 52 ft 40,000 lb 100% 360°
Insert 27 ft 10 in
on structural strength of boom extension
spread and do not exceed 85% of tipping loads, in
accordance with SAE J-765.
Pounds 2. 59 ft folding boom extension length may be
Feet
59 ft LENGTH WITH 26 ft INSERT 59 ft LENGTH WITH 52 ft INSERT
used for single line lifting service only.
Note: Lifting with the 36 ft extension base
0° 20° 40° 0° 20° 40° with either one or two 26 ft insert sections
OFFSET OFFSET OFFSET OFFSET OFFSET OFFSET
installed is not permitted.
60
7070 3. For main boom lengths less than 160 ft
(78) with the boom extension erected, the rated
7070 loads are determined by boom angle. Use
65 (77.5)
7070 4400 only the column which corresponds to the
70 (76.5) (78) boom extension length and offset for which
75
7070 4400 the machine is set up. For boom angles not
(75) (77.5) shown, use the rating of the next lower boom
7070 6610 4400
80
(74) (78) (76.5)
angle.
7070 6610 4400 4. WARNING: Operation of this machine with
85
(72.5) (77.5) (75.5) heavier loads than the capacities listed is
90 7070 6610 4400 4230 strictly prohibited. Machine tipping with
(71.5) (76) (74.5) (78) boom extension occurs rapidly and without
7070 6610 6400 4400 4230
95
(70) (75) (78) (73) (77.5) advance warning.
7070 6610 6400 4400 4230 5. Boom angle is the angle above or below
100
(69) (73.5) (77) (72) (76.5) horizontal of the longitudinal axis of the
105
7070 6610 6400 4400 4230 4000 boom base section after lifting rated load.
(67.5) (72.5) (76) (71) (75.5) (78)
6. Capacities listed are with outriggers properly
7070 6610 6400 4400 4230 4000
110 (66) (71) (74.5) (69.5) (74) (77) extended and vertical jacks set only.
6735 6545 6315 4400 4230 4000
115
(65) (69.5) (73) (68.5) (73) (75.5)
6400 6480 6230 4400 4230 4000
120
(63.5) (68) (71.5) (67.5) (72) (74.5)
5940 6170 5955 4400 4230 4000
125
(62) (67) (70) (66) (70.5) (73)
130 5480 5860 5680 4400 4230 4000
(60.5) (65.5) (68.5) (65) (69.5) (72)
135 4930 5510 5440 4110 4195 4000
(59.5) (64) (67) (63.5) (68) (70.5)
140 4380 5160 5200 3820 4160 4000
(58) (62.5) (65.5) (62.5) (67) (69)
3900 4645 4910 3350 3885 3785
145 (56.5) (61) (64) (61) (65.5) (68)
3420 4130 4620 2880 3610 3570
150 (55) (59.5) (62.5) (60) (64) (66.5)
3000 3680 4140 2470 3205 3365
155 (53.5) (58) (60.5) (58.5) (63) (65)
2580 3230 3660 2060 2800 3160
160
(51.5) (56.5) (59) (57) (61.5) (63.5)
2210 2825 3220 1690 2405 2810
165
(50) (54.5) (57.5) (56) (60) (62.5)
1840 2420 2780 2010 2460
170
(48.5) (53) (55.5) (59) (61)
175 1515 2060 2385 1655 2075
(46.5) (51) (53.5) (57.5) (59.5)
180 1700 1990 1690
(49.5) (51.5) (58)
1370 1625
185 (47.5) (49.5)
Min. boom 45 46 48 54 56 56
angle
for indicated
length
(no load)

Max. boom
length (ft) at 57 57
0° boom angle
(no load)
A6-829-101983A
NOTE: () Boom angles are in degrees

THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE.
12 The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane
 Load chart

NOTES:
1. Capacities are in pounds and do not exceed
42 ft - 86 ft 40,000 lb Pick & Carry Boom Centered 75% of tipping loads as determined by test in
up to 2.5 mph over Front accordance with SAE J-765.
2. Capacities are applicable to machines
Pounds equipped with 33.25x29 (38 ply) bias ply tires,
Feet at 85 psi cold inflation pressure.
3. Capacities appearing above the bold line are
Main boom length in feet based on structural strength and tipping
42 57 72 86 should not be relied upon as a capacity
61,750
limitation.
10 4. Capacities are applicable only with machine
(71.5)
12 61,750 on firm level surface.
(68.5) 5. On rubber lifting with boom extension not
15 49,000 34,600 permitted.
(63.5) (71.5)
34,750 34,600 6. Axle lockouts must be functioning when
20 lifting on rubber.
(55.5) (65.5)
25 34,750 34,600 7. For pick and carry operation, boom must be
(46) (60) centered over front of machine, mechanical
29,250 28,150 28,300
30 (34) (53.5) (62.5) swing lock engaged and load restrained
23,400 22,350 22,500 24,100 from swinging. When handling loads in the
35 (13) (46.5) (58) (64.5) structural range with capacities close to
40 17,750 17,800 19,250 maximum ratings, travel should be reduced
(38.5) (52.5) (60.5)
to creep speeds.
14,000 13,950 15,200
45 (28) (47) (56.5) 8. All lifting depends on proper tire inflation,
10,950 10,800 11,850 capacity and condition. Capacities must be
50 (7.5) (41) (52.5) reduced for lower tire inflation pressures. See
55 8150 9020 lifting capacity chart for tire used. Damaged
(34) (47.5)
tires are hazardous to safe operation of
60 5880 6600
(24.5) (42.5) crane.
4520 9. Creep – not over 200 ft of movement in any
65 (37) 30 minute period and not exceeding 1 mph.
70 2700
(30.5)
75 1110
(22)
Min. boom 0 20
angle for
indicated length
(no load)
Max. boom
length (ft) at 0° boom angle 72
(no load)

NOTE: () Boom angles are in degrees

Lifting capacities at zero degree boom angle

Boom
angle 42 57
0° 23,000 10,900
(35.3) (50)
A6-829-102108A

THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE.
Grove RT9130E-2 The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane 13
 Working range

160 ft main boom + 36 ft - 59 ft luffing extension

H [ft]

240
5° OFFSET 59' EXT.
20° OFFSET
230

220 40° OFFSET

210

200

190

180 160
70°
170
60°
160 145

Boom and extension length in feet

150
Height from the ground in feet

50° 130
140

130 115
40°
120
100
110

100 30° 76

90
72
80
20°
70 57

60
42
50
10°
40

30 78°
MAX.
BOOM
20 ANGLE
0°
10

0
220 210 200 190 180 170 160 150 140 130 120 110 100 90 80 70 60 50 40 30 20 10
Axis of
Rotation

Operating radius in feet from axis of rotation

Dimensions are for largest Grove furnished hook block

9' - 8" and headache ball, with anti-two block activated.
11' - 0"

THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE.
14 The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane
 Working range

160 ft main boom + 2 inserts + 36 ft - 59 ft luffing extension

H [ft]
290
5° OFFSET
59' EXT.
280 20° OFFSET

270 40° OFFSET

260

250

240

230

220

210

Boom and extension length in feet

200
Height from the ground in feet

190

180
160
70°
170

160 60° 145

150
130
50°
140

115
130
40°
120
100
110

86
100 30°

90
72
80
20° 57
70

60
42

50
10°
40
78°
30 MAX.
BOOM
20 ANGLE
0°
10

0
250 240 230 220 210 200 190 180 170 160 150 140 130 120 110 100 90 80 70 60 50 40 30 20 10
Axis of
Rotation
Operating radius in feet from axis of rotation

Dimensions are for largest Grove furnished hook block

9' - 8" and headache ball, with anti-two block activated.
11' - 0"

THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE.
Grove RT9130E-2 The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane 15
 Load chart

36 ft - 59 ft luffing folding boom extension (fixed angle) 100 ft main boom

NOTES:
1. All capacities above the bold line are based
100 ft 36 ft - 59 ft 40,000 lb 100% 360° on structural strength of boom extension.
27 ft 10 in
spread 2. 36 ft boom extension may be used for single
or double line lifting service. 59 ft boom
Pounds
extension may be used for single line lifting
Feet service only.
36 ft LENGTH 59 ft LENGTH
WARNING: Lifting with the 36 ft extension
5° 20° 40° 5° 20° 40°
OFFSET OFFSET OFFSET OFFSET OFFSET OFFSET base, with the 23 ft extension fly either
erected or folded along side of extension
32,600 base, is strictly prohibited.
30 (78)
30,700 *23,150 3. Radii listed are for a 100 ft boom with the
35 (76) (78) boom extension erected. For main boom
40
28,950 22,150 14,950 lengths less than 100 ft, the rated loads are
(74) (76.5) (77.5) determined by boom angle. Use only the
27,350 21,250 15,250 14,950 column which corresponds to the boom
45 (71.5) (74) (78) (75.5)
25,900 20,450 14,850 14,950 12,350 extension length and offset for which the
50 (69.5) (72) (75.5) (73.5) (78) machine is configured. For boom angles
55
24,600 19,700 14,500 14,550 11,900 not shown, use the rating of the next lower
(67) (69.5) (73) (72) (77) boom angle.
23,400 19,050 14,200 14,150 11,500
60 (64.5) (67) (70.5) (70) (75) WARNING: Operation of this machine with
22,300 18,450 13,900 13,750 11,100 8050 heavier loads than the capacities listed is
65 (62) (65) (68) (68) (73) (78) strictly prohibited. Machine tipping with
70
21,300 17,850 13,650 13,350 10,700 7850 boom extension occurs rapidly and without
(59.5) (62) (65.5) (66) (71) (76)
advance warning.
20,100 17,350 13,450 13,000 10,400 7660
75 (57) (59.5) (63) (64) (69) (73.5) 4. Boom angle is the angle above or below
18,100 16,900 13,300 12,550 10,050 7490 horizontal of the longitudinal axis of the
80 (54.5) (57) (60) (61.5) (66.5) (71.5) boom base section after lifting rated load.
85
16,000 16,500 13,150 12,000 9780 7340 5. Capacities listed are with outriggers properly
(51.5) (54) (57) (59.5) (64.5) (69)
extended and vertical jacks set only.
14,150 15,400 13,050 11,550 9510 7210
90 (49) (51.5) (54) (57.5) (62.5) (66.5)
12,500 13,700 13,000 11,100 9,260 7090
95 (46) (48) (50.5) (55) (60) (64)
11,050 12,100 12,750 10,650 9030 6980
100 (42.5) (45) (47) (52.5) (57.5) (61.5)
9770 10,650 10,250 8820 6900
105 (39) (41.5) (50) (55) (59)
8490 9270 9930 8620 6830
110 (35.5) (37.5) (47.5) (52.5) (56)
7400 8060 9040 8440 6790
115 (31) (33) (45) (49.5) (53)
6320 6850 8150 8260 6750
120 (26) (28) (42) (47) (50)
7240 7820
125 (39) (43.5)
6340 7380
130 (35.5) (40.5)
5570 6440
135 (32) (36.5)
4800 5510
140 (28) (32)
4100
145 (23)
3410
150 (16)
Min. boom
angle for 5° 20° 40° 5° 20° 40°
indicated
length (no load)
Max. boom
length (ft) at 100 ft 100 ft
5° boom angle
(no load)

NOTE: ( ) Boom angles are in degrees. A6-829-102550

*This capacity is based on maximum obtainable boom angle.

THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE.
16 The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane
 Load chart

36 ft - 59 ft luffing folding boom extension (fixed angle) 130 ft main boom

NOTES:
130 ft 36 ft - 59 ft 40,000 lb 100% 360° 1. All capacities above the bold line are based on
27 ft 10 in structural strength of boom extension.
spread 2. 36 ft boom extension may be used for single or
Pounds double line lifting service. 59 ft boom extension
Feet
may be used for single line lifting service only.
36 ft LENGTH 59 ft LENGTH WARNING: Lifting with the 36 ft extension
base, with the 23 ft extension fly either erected
5° 20° 40° 5° 20° 40°
OFFSET OFFSET OFFSET OFFSET OFFSET OFFSET or folded along side of extension base, is strictly
prohibited.
40 *23,350 3. Radii listed are for a 130 ft boom with the boom
(78)
extension erected. For main boom lengths less
45 23,350 *21,300 *12,300
(76) (78) (78) than 130 ft, the rated loads are determined
23,350 20,700 12,300 by boom angle. Use only the column which
50 (74) (76.5) (77.5) corresponds to the boom extension length and
55 23,350 20,100 14,850 12,300 offset for which the machine is configured. For
(72.5) (75) (78) (76)
23,350 19,500 14,550 12,300 11,600
boom angles not shown, use the rating of the
60 (70.5) (73) (76) (74.5) (78) next lower boom angle.
65 22,300 19,000 14,300 12,300 11,300 WARNING: Operation of this machine with
(68.5) (71) (74) (73) (77) heavier loads than the capacities listed is
70 20,350 18,500 14,050 12,300 10,950 strictly prohibited. Machine tipping with boom
(66.5) (69) (72) (71) (75)
18,350 18,050 13,850 12,300 10,700 7850 extension occurs rapidly and without advance
75 (64.5) (67) (70) (69.5) (73.5) (78) warning.
80 16,600 17,000 13,650 12,300 10,400 7690 4. Boom angle is the angle above or below
(62.5) (65) (68) (68) (72) (76) horizontal of the longitudinal axis of the boom
85 15,050 15,450 13,450 12,300 10,150 7550 base section after lifting rated load.
(60.5) (63) (66) (66) (70) (74.5)
13,650 14,050 13,300 12,250 9910 7420 5. Capacities listed are with outriggers properly
90
(58.5) (61) (63.5) (64.5) (68.5) (72.5) extended and vertical jacks set only.
95 12,400 12,800 13,150 11,900 9680 7300
(56.5) (58.5) (61.5) (62.5) (66.5) (70.5)
11,300 11,650 11,950 11,450 9460 7190
100 (54) (56.5) (59) (61) (64.5) (68.5)
105 10,300 10,650 10,950 10,500 9,260 7090
(52) (54) (56.5) (59) (63) (66.5)
110 9340 9660 9950 9580 9060 7000
(49.5) (52) (54) (57) (61) (64.5)
8480 8810 9070 8790 8800 6930
115 (47) (49.5) (51.5) (55) (59) (62.5)
120 7630 7970 8200 8010 8550 6860
(44.5) (46.5) (48.5) (53) (57) (60.5)
6700 7240 7430 7340 7840 6810
125 (41.5) (44) (45.5) (51) (54.5) (58)
130 5780 6510 6670 6680 7140 6770
(39) (41) (42.5) (49) (52.5) (55.5)
135 4980 5690 6100 6520 6500
(35.5) (37.5) (46.5) (50.5) (53.5)
4190 4880 5520 5910 6240
140 (32) (34) (44) (48) (50.5)
145 3500 4120 4860 5360 5640
(28) (30) (42) (45.5) (48)
2820 3360 4200 4820 5050
150 (23.5) (25.5) (39) (42.5) (45)
155 3580 4280
(36.5) (40)
160 2970 3750
(33.5) (36.5)
2430 3120
165 (30) (33)
170 1890 2490
(26) (29)
Min. boom
angle for 20° 20° 40° 20° 20° 40°
indicated
length (no load)
Max. boom
length (ft) at 100 ft 100 ft
5° boom angle
(no load)
NOTE: ( ) Boom angles are in degrees. A6-829-102554
*This capacity is based on maximum obtainable boom angle.

THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE.
Grove RT9130E-2 The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane 17
 Load chart

36 ft - 59 ft luffing folding boom extension (fixed angle) 160 ft main boom

NOTES:
1. All capacities above the bold line are based on
160 ft 36 ft - 59 ft 40,000 lb 100% 360° structural strength of boom extension and do not
27 ft 10 in
spread exceed 85% of tipping loads, in accordance with
SAE J765.
Pounds
2. 36 ft boom extension may be used for single or
Feet double line lifting service. 59 ft boom extension
36 ft LENGTH 59 ft LENGTH
may be used for single line lifting service only.
5° 20° 40° 5° 20° 40° WARNING: Lifting with the 36 ft extension base,
OFFSET OFFSET OFFSET OFFSET OFFSET OFFSET with the 23 ft extension fly either erected or folded
50 15,550 along side of extension base, is strictly prohibited.
(77.5) 3. Radii listed are for a 160 ft boom with the boom
55 15,550 extension erected. For main boom lengths less
(76)
15,550 14,950 9650 than 160 ft, the rated loads are determined
60 (74.5) (77.5) (78) by boom angle. Use only the column which
65 15,550 14,950 *14,400 9650 corresponds to the boom extension length and
(73) (76) (78) (77) offset for which the machine is configured. For
70 15,550 14,950 14,150 9650 9650 boom angles not shown, use the rating of the next
(71.5) (74.5) (77) (75.5) (78)
14,900 14,250 13,950 9650 9650 lower boom angle.
75 (70) (73) (75.5) (74) (77.5) WARNING: Operation of this machine with
80 14,100 13,550 13,400 9650 9650 heavier loads than the capacities listed is strictly
(68) (71) (74) (72.5) (76) prohibited. Machine tipping with boom extension
85 13,400 12,900 12,800 9650 9650 7630 occurs rapidly and without advance warning.
(66.5) (69.5) (72) (71) (74.5) (78)
12,700 12,250 12,200 9650 9650 7510 4. Boom angle is the angle above or below horizontal
90 (65) (68) (70.5) (69.5) (73) (77.5) of the longitudinal axis of the boom base section
95 11,500 11,700 11,650 9650 9650 7390 after lifting rated load.
(63) (66) (68.5) (68.5) (72) (75.5) 5. Capacities listed are with outriggers properly
10,400 10,850 11,100 9570 9420 7290
100 (61.5) (64.5) (67) (67) (70) (74) extended and vertical jacks set only.
9480 9910 10,200 9150 9010 7200
105 (59.5) (62.5) (65) (65) (68.5) (72.5)
110 8570 8970 9360 8730 8610 7110
(58) (61) (63) (63.5) (67) (71)
115 7780 8160 8530 8000 8220 7030
(56) (59) (61) (62) (65.5) (69.5)
120 6990 7360 7700 7280 7840 6950
(54) (57) (59) (60.5) (64) (67.5)
125 6320 6670 6980 6620 7180 6890
(52) (55) (57) (59) (62.5) (66)
130 5650 5980 6260 5970 6530 6830
(50) (53) (55) (57.5) (60.5) (64)
135 5070 5380 5630 5400 5930 6320
(48) (51) (53) (55.5) (59) (62.5)
140 4500 4780 5010 4830 5340 5820
(46) (49) (50.5) (54) (57) (60.5)
145 3990 4250 4450 4340 4820 5260
(43.5) (46.5) (48) (52) (55.5) (58.5)
150 3490 3730 3900 3850 4300 4710
(41.5) (44) (45.5) (50) (53.5) (56.5)
155 2990 3260 3410 3840 4210
(38.5) (41.5) (48) (51.5) (54.5)
160 2490 2800 2980 3380 3710
(36) (38.5) (46) (49.5) (52)
165 1970 2300 2590 2960 3250
(33) (36) (44) (47.5) (50)
170 1450 1800 2210 2550 2790
(30) (32.5) (42) (45) (47.5)
1800 2170
175 (39.5) (43)
1390 1800
180 (37.5) (40)
185 1420
(37.5)
Min. boom
angle for
26° 29° 40° 34° 36° 40°
indicated
length (no load)
Max. boom
length (ft) at 100 ft 100 ft
5° boom angle
(no load)
NOTE: ( ) Boom angles are in degrees. A6-829-102558
*This capacity is based on maximum obtainable boom angle.

THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE.
18 The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane
 Load chart

59 ft luffing folding boom extension with 1 or 2 inserts (fixed angle) 160 ft main boom

NOTES:
1. All capacities above the bold line are based on
160 ft 59 ft 26 ft 52 ft 40,000 lb 100% 360°
insert 27 ft 10 in
structural strength of boom extension and do
spread not exceed 85% of tipping loads, in accordance
with SAE J-765.
Pounds
Feet
2. 59 ft folding boom extension length may be
59 ft LENGTH WITH 26 ft INSERT 59 ft LENGTH WITH 52 ft INSERT used for single line lifting service only.
NOTE: Lifting with the 36 ft extension base with
5° 20° 40° 5° 20° 40° either one or two 26 ft insert sections installed is
OFFSET OFFSET OFFSET OFFSET OFFSET OFFSET
not permitted.
70
6830 3. For main boom lengths less than 160 ft with
(78)
the boom extension erected, the rated loads
6830 4400
75 (77) (78) are determined by boom angle. Use only
6830 6610 4400 the column which corresponds to the boom
80
(75.5) (78) (77.5) extension length and offset for which the
85 6830 6610 4400 machine is set up. For boom angles not shown,
(74.5) (77.5) (76.5)
use the rating of the next lower boom angle.
6830 6610 4400 4230
90
(73) (76) (75.5) (78) 4. WARNING: Operation of this machine with
6830 6610 6400 4400 4230 heavier loads than the capacities listed is
95
(72) (75) (78) (74.5) (77.5) strictly prohibited. Machine tipping with boom
6830 6610 6400 4400 4230 extension occurs rapidly and without advance
100
(70.5) (73.5) (77) (73) (76.5)
warning.
6830 6610 6400 4400 4230 4000
105 5. Boom angle is the angle above or below
(69.5) (72.5) (76) (72) (75.5) (78)
6830 6610 6400 4400 4230 4000 horizontal of the longitudinal axis of the boom
110
(68) (71) (74.5) (71) (74) (77) base section after lifting rated load.
6590 6520 6310 4400 4230 4000 6. Capacities listed are with outriggers properly
115
(66.5) (69.5) (73) (69.5) (73) (75.5)
6350 6430 6230 4400 4230 4000
extended and vertical jacks set only.
120
(65) (68) (71.5) (68.5) (72) (74.5)
5910 6120 5950 4400 4230 4000
125
(64) (67) (70) (67.5) (70.5) (73)
5480 5810 5680 4400 4230 4000
130
(62.5) (65.5) (68.5) (66) (69.5) (72)
4930 5480 5430 4110 4170 4000
135
(61) (64) (67) (65) (68) (70.5)
4380 5160 5190 3820 4120 4000
140
(59.5) (62.5) (65.5) (63.5) (67) (69)
3900 4640 4900 3350 3860 3780
145
(58) (61) (64) (62.5) (65.5) (68)
3420 4130 4620 2880 3610 3570
150
(56.5) (59.5) (62.5) (61) (64) (66.5)
3000 3680 4140 2470 3200 3360
155
(55) (58) (60.5) (59.5) (63) (65)
2580 3230 3660 2060 2800 3160
160
(53.5) (56.5) (59) (58.5) (61.5) (63.5)
2210 2820 3220 1690 2400 2810
165
(52) (54.5) (57.5) (57) (60) (62.5)
1840 2420 2780 2010 2460
170 (50) (53) (55.5) (59) (61)
1510 2060 2380 1650 2070
175 (48.5) (51) (53.5) (57.5) (59.5)
1700 1990 1690
180 (49.5) (51.5) (58)
Min. boom 46° 46° 48° 55° 56° 56°
angle for
indicated
length (no load)
Max. boom 57 ft 57 ft
length (ft) at
5° boom angle
(no load)

NOTE: ( ) Boom angles are in degrees. A6-829-102562

THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE.
Grove RT9130E-2 The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane 19
 Load chart

36 ft - 59 ft luffing folding boom extension 160 ft main boom (load luffing)

NOTES:
160 ft 36 ft - 59 ft 40,000 lb 100% 360° 1. All capacities above the bold line are based on
27 ft 10 in structural strength of boom extension and do not
spread exceed 85% of tipping loads, in accordance with
Pounds SAE J-765.
Feet 2. 36 ft boom extension length may be used for
36 ft LENGTH 59 ft LENGTH single or double line lifting service. 59 ft boom
extension may be used for single line lifting service
5° - 20° 20° - 40° 5° - 20° 20° - 40°
OFFSET OFFSET OFFSET OFFSET only.
WARNING: Lifting with the 36 ft extension base,
60 14,950 with the 23 ft extension fly either erected or folded
along side of extension base, is strictly prohibited.
65 14,950 10,250 3. Capacities are applicable for a 160 ft main boom
70 14,950 10,050 9650
length only.
WARNING: Operation of this machine with
75 14,250 9840 9320 heavier loads than the capacities listed is strictly
prohibited. Machine tipping with boom extension
80 13,550 9640 8950 occurs rapidly and without advance warning.
85 12,900 9460 8600 5100
4. The loads for luffing depend on the angle of the
main boom, angle of the boom extension and
90 12,250 9280 8290 4980 dynamic working pressure of the luffing cylinder
for the boom extension.
95 11,500 9130 7990 4880 5. Capacities listed are with outriggers properly
100 10,400 8980 7720 4780 extended and vertical jacks set only.

105 9480 8850 7470 4690

110 8570 8720 7220 4600

115 7780 8160 7010 4520

120 6990 7360 6790 4440

125 6320 6670 6600 4370

130 5650 5980 5970 4310

135 5070 5380 5400 4250

140 4500 4780 4830 4200

145 3990 4250 4340 4160

150 3490 3730 3850 4120

155 2990 3410 3840

160 2490 2980 3380

165 1970 2590 2960

170 1450 2210 2550

175 1800

180 1390

Min. boom
angle for 29° 40° 36° 40°
indicated
length (no load)

Max. boom
length (ft) at 100 ft 100 ft
5° boom angle
(no load)

A6-829-102575

THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE.
20 The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane
 Load chart

59 ft luffing folding boom extension with 1 or 2 inserts 160 ft main boom (load luffing)

NOTES:
1. All capacities above the bold line are based on
160 ft 59 ft 26 ft - 52 ft 40,000 lb 100% 360° structural strength of boom extension and do not
Insert 27 ft 10 in exceed 85% of tipping loads, in accordance with
spread
Pounds
SAE J-765.
2. 59 ft boom extension may be used for single line
Feet lifting service only.
59 ft LENGTH with 26 ft INSERT 59 ft LENGTH with 52 ft INSERT
WARNING: Lifting with the 36 ft extension
5° - 20° 20° - 40° 5° - 20° 20° - 40° base, with either one or two 26 ft insert sections
OFFSET OFFSET OFFSET OFFSET installed is not permitted.
3. Capacities are applicable for a 160 ft main boom
80 6610 length only.
85 6610 WARNING: Operation of this machine with
heavier loads than the capacities listed is strictly
90 6610 4230 prohibited. Machine tipping with boom extension
occurs rapidly and without advance warning.
95 6610 4420 4230
4. The loads for luffing depend on the angle of the
100 6610 4330 4230 main boom, angle of the boom extension and
dynamic working pressure of the luffing cylinder
105 6610 4250 4230 4000 for the boom extension.
5. Capacities listed are with outriggers properly
110 6430 4180 4230 4000
extended and vertical jacks set only.
115 6250 4100 4230 4000

120 6070 4020 4230 4000

125 5900 3970 4230 4000

130 5480 3920 4230 4000

135 4930 3870 4110 4000

140 4380 3810 3820 3960

145 3900 3770 3350 3780

150 3420 3730 2880 3570

155 3000 3680 2470 3200

160 2580 3230 2060 2800

165 2210 2820 1690 2400

170 1840 2420 2010

175 1510 2060 1650

180 1700

Min. boom
angle for
46° 48° 56° 56°
indicated
length (no load)

Max. boom
length (ft) at
5° boom angle 57 ft 57 ft
(no load)

A6-829-102579

THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE.
Grove RT9130E-2 The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane 21
 Load chart

Installation and removal of counterweight and auxiliary hoist rated lifting capacities in pounds

On outriggers fully extended- 360°

Radius in feet Main boom length 42 ft*
10 48,000
12 48,000
15 48,000
20 48,000
25 48,000
30 48,000

Installation and removal of front and rear outrigger boxes rated lifting capacities in pounds without counterweight

On rubber (stationary) - 360°

Radius in feet Main boom length 42 ft*
10 11,600
12 11,600
15 11,600
20 11,600

* The boom must be fully retracted.

Notes for on rubber

• Capacities are applicable to machines equipped with Titan 33.25 x 29 (38 ply) tires at 85 psi
cold inflation pressure Capacities do not exceed 75% of tipping loads as determined by test in
accordance with SAE J765.
• With no load, the boom angle must not be less than 35˚ when over sides of machine since loss
of stability will occur causing a tipping condition. To lower boom below 35˚ boom angle, boom
must be swung over front or rear and LMI bypass activated.
• Once one outrigger box is installed, do not swing load over that end of the machine while
installing the other outrigger box.
• Each outrigger box assembly weighs 9427 lb including the outrigger beams and pads.
• May be used for single or double line lifting service.

THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE.
22 The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane
 Load handling

Weight reductions for load handling devices Line pulls and reeving information
36 ft - 59 ft manual boom extension Pounds Nominal
Permissable
Hoists Cable specs cable
line pulls
*36 ft extension (erected) 5260 length

*59 ft extension (erected) 9860 19 mm (3/4 in)

Main 6 x 37 class, EIPS,
Manual extension with 26 ft insert Pounds 16,800 lb* 950 ft
Model 35 IWRC Special Flexible
Min. breaking strength 58,800 lb
*59 ft extension (erected) 14,100
Manual extension with 52 ft insert Pounds 19 mm (3/4 in) 35 x 7 Class
Main
Rotation resistant (non-rotating) 16,800 lb* 950 ft
*59 ft extension (erected) 19,400 Model 35
Min. breaking strength 85,500 lb
*Reduction of main boom capacities (no deduct required for stowed
boom extension. 22 mm K™-100 Synthetic
(no deduct required for stowed boom extension) Main
hoist rope (ISO) 16,800 lb* 971 ft
When lifting over boom nose with 36 ft or 59 ft extension erected, the Model 35
outriggers must be fully extended or 50% extended (19 ft 9 in) spread. Min. breaking strength 84,000 lb
When lifting over main boom nose with 26 ft or 52 ft insert erected, the
outriggers must be fully extended.
19 mm (3/4 in) 35 x 7 Class
Auxiliary
Rotation resistant (non-rotating) 16,800 lb* 700 ft
Model 35
Auxiliary boom nose Pounds Min. breaking strength 85,500 lb

120
22 mm K™-100 synthetic
Auxiliary
Hook blocks and headache balls Pounds hoist rope (ISO) 16,800 lb* 722 ft
Model 35
Min. breaking strength 84,000 lb
80 USt, 5-sheave 1600+

130 USt, 8-sheave 2545+ The approximate weight of 3/4 in wire rope is 1.5 lb/ft.
The approximate weight of 22 mm synthetic rope is 0.21 lb/ft.
10 USt overhaul ball 730+ *With certain boom and hoist tackle combinations, the allowable line pull may be
limited by hoist performance. Refer to Hoist Performance table for lift planning to
+Refer to rating plate for actual weight. ensure adequate hoist performance on drum rope layer required.
When lifting over swingaway and/or jib combinations, deduct total
weight of all load handling devices reeved over main boom nose
directly from swingaway or jib capacity.
NOTE: All load handling devices and boom attachments are considered Hoist performance
part of the load and suitable allowances MUST BE MADE for their Wire
combined weights. Weights are for Grove furnished equipment. Hoist line pulls
rope Drum rope capacity (ft)
two-speed hoist
layer
Low High Layer Total
Capacity reductions for synthetic rope use available lb* available lb*

Main boom Extension 1 19,267 11,094 136 136

charts charts
2 17,709 10,197 148 285
Outriggers fully extended 200 lb 0 lb
3 16,384 9434 160 445
Outriggers 50% extended 1130 lb 410 lb
4 15,243 8777 172 618
Outriggers 0% extended 1740 lb N/A
5 14,251 8206 184 802
Rubber 460 lb N/A 6 13,380 7705 196 998
If synthetic rope is installed on either the main or auxiliary hoist, and
wire rope is installed on the other hoist, no capacity reductions are * Max lifting capacity: 6 x 37 class and 35 x 7 class = 16,800 lb
required. Note: Synthetic rpe layer height may vary and may reduce available line pull per layer.

Working area diagram

REAR AXLE
CENTERLINE 360° CENTERLINE 360° OSCILLATION
OVER OF OUTRIGGER LOCKOUTS MUST
OF BOOM SIDE SUPPORT BE SET TO
BOOM MAINTAIN 360°
CENTERED CAPACITIES
LONGITUDINAL OVER FRONT
CENTERLINE
OF CRANE
6°
CG OF OVER OVER
LOAD 12°
FRONT REAR
SEE NOTE FRONT
AT BOTTOM

DIAGRAM
FOR LIFTING CENTERLINE DIAGRAM C6-829-003529
ON OUTRIGGERS OVER OF ROTATION FOR LIFTING C6-829-001159
SIDE ON TIRES

Bold lines determine the limiting position of any load for operation within working areas indicated.

THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE.
Grove RT9130E-2 The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane 23
 Specifications

Superstructure
Cab
20° tilt, full-vision, all-steel fabricated with acoustical lining and tinted
Boom safety glass throughout. Deluxe seat incorporates armrest-mounted hydraulic
12,8 m - 48,8 m (42 ft - 160 ft) five-section, sequenced synchronized full single-axis controllers. Tilt/telescoping steering wheel with various controls
power boom. Maximum tip height: 51,5 m (169 ft) incorporated into the steering column. Other standard features include: hot
water heater, cab circulating air fan, sliding side and rear windows, sliding
skylight with electric wiper and sunscreen, electric windshield wash/wipe, fire
Lattice extension extinquisher, seat belt, air conditioning, and dual cab mounted work lights.
11 m - 18 m (36 ft - 59 ft) offsettable bifold lattice swingaway extension.
Offsets 0°, 20° and 40°. Stows alongside base boom section.
Maximum tip height: 69,2 m (227 ft) Swing
Two speed, (2) planetary swing drives with foot applied multi-disc wet brakes.
Spring applied, hydraulically released swing brakes. 360° positive swing lock
*Optional lattice extension and two-position mechanical house lock, both operated from cab. Maximum
11 m - 18 m (36 ft - 59 ft) hydraulically offsettable bifold lattice swingaway speed: 2.5 rpm
extension. Offsets from 0° to 40°. Stows alongside base boom section.
Maximum tip height: 69,2 m (227 ft)
Hydraulic system
Six main pumps with a combined capacity of 776 LPM (205 GPM).
*Optional lattice extension inserts
Two 8 m (26 ft) lattice extension inserts. Installs between the boom nose and Maximum operating pressure: 331 bar (4800 psi).
bifold extension, nonstowable. Maximum tip height: 85 m (279 ft) Two individual post pressure compensated valve banks. Return line type filter
with full flow by-pass protection and service indicator. Replaceable cartridge
with micron filtration rating of 19/17/14.
Boom nose 1230 L (325 gal) reservoir. Remote mounted oil cooler with thermostatically
Seven nylatron sheaves mounted on heavy duty tapered roller bearings with controlled hydraulic driven motor, fan/air to oil. System pressure test ports.
removable pin-type rope guards. Quick reeving type boom nose. Removable
auxiliary boom nose with removable pin type rope guard.
Hoist (main and auxiliary hoist)
Planetary reduction with automatic spring applied multi-disc brake. Grooved
Boom elevation drum electronic hoist drum rotation indicator, and hoist drum cable followers.
One double acting hydraulic cylinder with integral holding valve provides
elevation from -3° to 78°.
Maximum hoist single line pull:
1st layer - 8740 kg (19,267 lb)
Load moment and anti-two block system 3rd layer - 7432 kg (16,384 lb)
Standard “Graphic Display” load moment and anti-two block system with 5th layer - 6464 kg (14,251 lb)
audio-visual warning and control lever lockout. These systems provide
electronic display of boom angle, length, radius, tip height, relative load Maximum permissible single line pull:
moment, maximum permissible load, load indication and warning of 7620 kg (16,800 lb) with 35 x 7 class rope
impending two-block condition. The standard Work Area Definition System
allows the operator to pre-select and define safe working areas. If the crane Maximum single line speed: 171 m/min (562 fpm)
approaches the pre-set limits, audio-visual warnings aid the operator in avoiding
job-site obstructions. Rope class:
35 x 7 EIPS WSC, Rotation Resistant

Counterweight Rope diameter: 19 mm (3/4 in)

18 144 kg (40,000 lb) of total counterweight. Hydraulically installed and
removed. Rope length:
Main hoist - 290 m (950 ft)
Auxiliary hoist - 214 m (702 ft.)

Maximum rope stowage: 368 m (1206 ft)

* Denotes optional equipment

24
 Specifications

Carrier
Steering
Fully independent power steering:
Chassis Front: Full hydraulic steering wheel controlled.
Box section frame fabricated from high-strength, low alloy steel. Removable Rear: Full hydraulic switch controlled.
outrigger housings, front/rear towing and tie down lugs. Provides infinite variations of four main steering modes: front only, rear only,
crab and coordinated. Rear steer centered indicator light.

Outrigger system Tires

Four hydraulic telescoping single-stage double box beam outriggers with Standard 33.25 x 29 - 38 bias ply.
inverted jacks and integral holding valves. Three position settings, 0%, 50%
and fully extended. Outrigger boxes removable for ease of transportation. All
steel fabricated, quick release type outrigger floats, 775 m (30.5 in) diameter. Electrical system
Maximum outrigger pad load - 75 298 kg (166,000 lb). Outrigger Monitoring Three 12 V - maintenance free batteries. 12 V starting and lighting, circuit
System comes standard (required for North America, Canada and the European breakers.
Union).

Lighting
Outrigger controls Full lighting including turn indicators, head, tail, brake and hazard warning
Controls and crane level indicator located in cab.
lights.

Maximum Drive Speed

24 km/h (15 mph)
Engine (Tier 4F)
Cummins QSL8.9L diesel, six cylinder, turbo-charged with Cummins Compact
Catalyst (CCC) and Selective Catalytic Reduction (SCR) combo muffler, Gradeability (theoretical)
using Diesel Exhaust Fluid (DEF) injection. Meets emission per U.S. Tier 4F 73% (Based on 79 913 kg [176,175 lb] GVW) 33.25 x 29 tires, pumps
and E.U. Stage IV.239 kW (320 bhp) gross at 2200 rpm. Maximum torque: engaged, 48,8 m (160 ft) boom, plus 18 m (59 ft) swingaway, 18 144 kg
1383 Nm (1020 ft lb) at 1500 rpm. Fuel requirements: Maximum of 15 PPM (40,000 lb) counterweight, hook block and headache ball.
sulphur content (Ultra low diesel fuel) and diesel exhaust fluid (DEF).
NOTE: Tier 4F engine required in North American and European Union Miscellaneous standard equipment
countries. Full width aluminum fenders, full length aluminum decking, dual rear view
mirrors, hook block tie down, electronic back-up alarm, light package, front
stowage well, tachometer/hourmeter, immersion type block heater, rear wheel
Engine (Tier 3) position indicator, hot water cab heater, air conditioning, hoist mirrors, engine
Cummins QSC8.3L diesel, six cylinders, 224 kW (300 bhp) (Gross) at 2200 distress A/V warning system, front/rear tie down and tow lugs, coolant sight
rpm. Maximum torque: 1356 Nm (1000 ft lb) at 1600 rpm. level indicator, hydraulic pump disconnect, LMI light bar. Hydraulically
NOTE: Required for sale outside of N.A. and European Union. activated boom removal pins, lift cylinder travel support, 80 USt hook block,
10 USt top swivel ball, CraneSTAR asset management system.

Fuel tank capacity *Optional equipment

379 L (100 gal) • AUXILIARY LIGHTING AND CONVENIENCE PACKAGE: Includes
superstructure mounted amber flashing light, dual base boom mounted
floodlights, and rubber mat for stowage trough.
Transmission • 130 USt hook block
Full powershift with 6 forward and 3 reverse speeds. Front axle disconnect for • Rear pintle hook
4 x 2 travel. • PAT event recorder down load kit
• Wind speed indicator (wireless)
• Third wrap indicator with hoist cut-out (main and auxiliary)
Axles • -29°C/-20°F Cold Weather Package
Cab controlled cross axle differential locks, (front and rear) • -40°C/-40°F Arctic Package
• Synthetic rope for main and/or auxiliary hoist
Front: Drive/steer with differential and planetary reduction hubs rigid mounted • Vertical L.M.I. light tower
to frame. • Auxiliary hydraulic oil cooler

Rear: Drive/steer with differential and planetary reduction hubs pivot mounted
to frame.

Brakes
Full hydraulic split circuit, dry disc service brakes operating on all wheels.
Spring-applied, hydraulically released parking brake mounted on front axle.

* Denotes optional equipment

Grove RT9130E-2 25
 Symbols glossary

Axles Crane control system Heavy duty jib Outriggers

Boom Drive Height (no max) Radius

Boom elevation Electrical system Hoist Rotation

Boom extension Engine Hook block

H Speed

Extension
Boom length Hydraulic system Steering

Boom nose Frame Insert Suspension

Brakes Fuel tank capacity Lights Swing

Cab Gear Oil Tires

Counterweight Grade Outrigger controls Transmission

26
 Notes

Grove RT9130E-2 27
 Manitowoc Cranes

Regional headquarters
Americas Europe, Middle East, Africa China Greater Asia-Pacific
Manitowoc, Wisconsin, USA Dardilly, France - TOWERS Shanghai, China Singapore
Tel: +1 920 684 6621 Tel: +33 (0)4 72 18 20 20 Tel: +86 21 6457 0066 Tel: +65 6264 1188
Fax: +1 920 683 6277 Fax: +33 (0)4 72 18 20 00 Fax: +86 21 6457 4955 Fax: +65 6862 4040
Shady Grove, Pennsylvania, USA Wilhelmshaven, Germany - MOBILE
Tel: +1 717 597 8121 Tel: +49 (0) 4421 294 454
Fax: +1 717 597 4062 Fax: +49 (0) 4421 2944301

Manitowoc Crane Care when you need it. Manitowoc Finance helps you get right to
The assurance of the world’s most advanced crane service and work generating profits for your business.
support to get you back to work fast. Financial tools that help you capitalize on opportunity with
solutions that fit your needs.

This document is non-contractual. Constant improvement and engineering progress

make it necessary that we reserve the right to make specification, equipment, and price
changes without notice. Illustrations shown may include optional equipment and acces-
sories and may not include all standard equipment.

©2016 All Rights Reserved – Manitowoc Cranes, LLC and its affiliates.
Form No. RT9130E-2 PG
Part No. 11-006-2M-0616
www.manitowoccranes.com