Sika Monotop Panel Patch Pds

April 2016
®
Sika MonoTop Panel Patch
High build cement based ultra-light weight patching mortar
Description Sika MonoTop Panel Patch is a fine cementitious polymer modified mortar for
use as a non-structural repair smooth finishing for surface damaged concrete
and pre-cast panels.
Uses As a trowel applied coat over joining plate recesses of precast concrete
panels, in vertical, horizontal and overhead for non-structural applications.
Construction
Restores the appearance of honeycombed or surface impaired concrete
caused by faulty formwork. Provides a smooth surface that will allow
protective and other architectural coatings to be applied free of pin holes.
Patch repairs to Precast panels and joiner plates.
As a repair and reprofiling mortar for concrete joint edges, corner fillets etc.
Advantages  One component system requires only the addition of water.

 Easily applied and worked.
 Adjustable consistency to suit application.
 Available in two colours, grey and off-white.
 Excellent bonding to substrate.
 Reduced shrinkage
 High Build repairs 5mm-75mm
Storage and Shelf Life Stored in the original sealed packaging in dry conditions, this product will
keep for at least nine (9) months.
Instructions for Use
Surface Preparation Correct and thorough surface preparation is essential to achieve the high
adhesive qualities of Sika MonoTop mortars.
All surfaces must be dry, clean, sound and free from dust, ice, oils, grease or
other surface contaminants such as curing membranes and form release
agents, etc.
Concrete, Mortar, Stone: Mechanically abrade the surface with a needle gun,
mechanical wire brush, grind, grit or water blast. All surface laitance must be
removed.
Mixing Sika MonoTop Panel Patch should be mechanically mixed in a forced action
mixer or in a clean drum using a drill and spiral mixer at a speed of
approximately 200 rpm. Mixing time should be at least 3 minutes until a
smooth consistency of uniform colour and texture is achieved.
Application Sika MonoTop Panel Patch must be applied by trowel. Best results are
obtained when the substrate and ambient temperatures are falling. It is
recommended to apply Sika MonoTop Panel Patch at temperatures above
8 °C and less than 30 °C.
Application Thickness Typically, the product is placed between 5mm to 75 mm in thickness.
Application thickness varies depending on the consistency and orientation of
the void.
Cleaning Remove soft Sika MonoTop Panel Patch from tools and equipment with
water. Hardened material can only be removed mechanically.
®
Page 1 of 2
April 2016
Technical Data (Typical)

Form Smooth, paste like mortar
Density (mixed) Approx. 900 kg/m³
Yield Approx. 17-18litres per bag
Mixing ratio Water : Powder

To one bag of Sika MonoTop Panel Patch add 3.5 to 4.4 litres of water.
Potlife at 20°C 120 minutes approx.
+8°C - +30°C (substrate and ambient temperatures)
Construction
Application temperature
+5°C - +25°C (mortar temperature)
Compressive strength Approx. 10 MPa at 28 days
Colours Available in Light Grey and Off-white
Consumption/Coverage Approx. 0.75 kg/m² per mm thickness
(dependent on surface profile, texture, temperature, loss and wastage)
Packaging 12 kg bag
 Application
Important Notes
- apply only to clean, sound substrates
- The surface moisture needs to be less than 15%.
- large blowholes and very rough surfaces should be prefilled
 Mixing
- Sika MonoTop Panel Patch has various uses while may
necessitate adjusting the consistency slightly to better suit the
particular application.
 Limitations
- Sika MonoTop Panel Patch should not be used in temperatures
lower than 8°C
- For Non-structural repairs only, Non-trafficable applications.
- Application should not take place when rainfall is occurring or is
likely to occur (unless sheltered or protected).
- Do not expose the Sika MonoTop Panel Patch to running water
during and after application, until it has hardened.
- Sika MonoTop Panel Patch does not bridge moving cracks.
- The material is not suitable for use as an adhesive for ceramic
tiles.
Handling Precautions  Avoid contact with the skin.

 Protective gloves and clothing are recommended when mixing or using
this product.
 A full material safety data sheet is available from Sika on request.
Important Notification The information, and, in particular, the recommendations relating to the application and
end-use of Sika’s products, are given in good faith based on Sika’s current knowledge
and experience of the products when properly stored, handled and applied under
normal conditions. In practice, the differences in materials, substrates and actual site
conditions are such that no warranty in respect of merchantability or of fitness for a
particular purpose, nor any liability arising out of any legal relationship whatsoever, can
be inferred either from this information, or from any written recommendations, or from
any other advice offered. The proprietary rights of third parties must be observed. All
orders are accepted subject of our terms and conditions of sale. Users should always
refer to the most recent issue of the Australian version of the Technical Data Sheet for
the product concerned, copies of which will be supplied on request.
PLEASE CONSULT OUR TECHNICAL DEPARTMENT FOR FURTHER
INFORMATION.
®
Page 2 of 2

Sika Monotop Panel Patch Pds

Uploaded by

Copyright:

Available Formats

Sika Monotop Panel Patch Pds

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Sika Monotop Panel Patch Pds

Uploaded by

Copyright:

Available Formats

April 2016

Advantages  One component system requires only the addition of water.

Instructions for Use

Technical Data (Typical)

Density (mixed) Approx. 900 kg/m³

Yield Approx. 17-18litres per bag

Mixing ratio Water : Powder

Handling Precautions  Avoid contact with the skin.

You might also like