Conveyor Calculation

Design Considerations
 Characteristics and Conveyability of Bulk Materials

 Capacities, Belt Widths, and Speeds
 Belt Conveyor Idlers
 Belt Tension, Power, and Drive Engineering
 Belt Selection
 Pulleys and Shafts
 Vertical Curves
 Steep Angle Conveying
 Belt Takeups, Cleaners, and Accessories
 Conveyor Loading and Discharge
 Conveyor Motor Drives and Controls
 Operation, Maintenance, and Safety
k Materials
COUNTER WEIGHT CALCULATOR
PROJECT : BY PASS CONVEYOR
Belt width 1800 mm Friction Factor (f)

Tensile strength of belt NN200 x 5 X 5/1.5 f 0.03
Horizontal length of conveyor 528.8 m Lo 49
C to C conveyor length L 548.5 m
Height of level head pulley H 9.8 m
Belt speed V 198 m/min
Material to handled COAL Weight of moving parts without material carr
Conveyor Capacity Q 2400 Ton/hours W 154
P1 = Power required to move empty belt (kW) Pt

= 0.06 x f x W x V (L + Lo)
367
= 89.36 kW
P2 = Power required to move load on level (kW)

= f x Q (L + Lo)
367
= 117.23 kW
P3 = Power to Lift load (kW) P

= HxQ ( + ) value for ascent conveyor
367 ( - ) value for descent conveyor
= 64.09 kW
Effective tension (Te) = 6120 x P

V FRICTION FACTOR
= 8366.48 kg 0.2
Slack Side Tension (T2) = Te x 1/e (Driving Coeffecient Factor) DRIVING COEFFECIENT FACTOR
1.14
= 9537.79 kg
Slope Tension (T3) = W1 ( H +/- f x L ) BELT WEIGHT STANDART (W1)

= 1207.73 kg 46 kg/m
Sag Tension (T4) = 50/8 x Lr x W1 RETURN IDLER SPACING (Lr)

3m
= 862.5 kg
Counter Weight Calculation (Wt)~ 2 x T2 = 19075.58 kg Choise the Larger Tension

~ 2 x T4 = 1725 kg
rts without material carried
= Power to move Tripper (kW)
= Total Power
= P1 + P2 + P3 + Pt
= 270.68 kW
1 Belt Cleaning Systems 7 Other Accessories
2 Belt Guiding Systems 8 Conveyor Belts
3 Sealing Systems 9 Idlers
4 Loading Systems 10 Pulleys
5 Pulley Lagging Systems 11 Hoods
6 HiSafe Systems 12 Holdbacks
4.1 COAL DATA:
Capacity : 2000 tons per hour
Material : Coal
Density : 50 lbs per cubic foot
Grindability : 45 to 65 Hardgrove
Infeed to the receiving hopper;

Lump Size : 6 in to 0
Infeed to the secondary crusher;
Lump Size : 2 in to 0
SPEED 800 FEED PER MNEIT
4.064008 m/s
belt width 42 inch
Material : Coal , anthracite, sized
Average Weight : 60 lbs/ cub.ft
angle of repose : 35 degrees
recommended max
inclination : 18 degrees
Code : B35TY
SPESIFIKASI MATERIAL
Material : Coal , anthracite, sized
Capacity : 2000 tph
Length : 200 m
Lift : 115 feet
Belt Speed : 600 fpm

Belt width 42 inches
anthracite, sized
BELT CONVEYOR CAPACITY TABLE
Surcharge angle of The

Material : 15 degrees
Density of Material : 60 lb/ft3
Capacity : 2000 tph
ft3/hr : 66666.67 ft3/hr
equivalent Capacity : 11111.11
BELT CPONVEYOR PARAMETER
Belt Speed : 600 fpm

Belt width : 42 inches
Surchage Angle 15 degrees
Trough Angle : 35 degrees
Cross section of load 1254 ft2
Capacity at 100 fpm 7254 ft3/hr
IDLER
Trough Angle : 35 degrees
CAPACITY : 1.531722
Belt Width : 42 inches
Weight of Material : 50 lb/ft3
Trough idle spacing : 4.5 ft
Return idler : 10 ft
5-15 less than
angle of repose
55-60
CALCULATED IDLER LOAD
Belt Weight(WB : 42 inch

Material Wight(WM) : lbs/f
Quantity of Material
Conveyed(Q) : 2000 tph
Design Belt Speed(Vee) : fpm

Spacing of Idlers(SI) : 4.5 f
Lump Adjustment
Factor(KI) : 1 lbs/f
Idler Measurement
Load :
isalignment inch
Belt Tension lbs
Idler spacing(f) f
No Komponen
1. Frame Structure
1.1 Hollow sq. bar SS-41, 50 x 50 x 2,3t - 6mL
1.5 Angle bar SS-41, L-50 x 50 x 6t x 6mL
1.6 Angle bar SS-41, L-65 x 65 x 6t x 6mL
1.7 L-profile, SS-41 (150 x 50 x 5t) - 6 mL
1.8 Z-profile, SS-41 (150x46x40x1,5t) -6Ml
1.9 UNP SS-41, 150 x 75 x 6,5t x 6mL
1.10 UNP SS-41, 100 x 50 x 5t x 6mL
1.11 Grating GI, Type-30/100 (Bar:3x30) - 800Wx1000L
1.12 Grating treads GI, Type-30/100 (Bar:3x30) - 70x240x800
2. Drive Unit
2.1 Head pulley - 500D x 1400L
2.2 Tail pulley - 400D x 1400L
2.3 Snub pulley - 350D x 1400L
2.4 Conv.Belt - 1200w - EP400 / 3 - 3.2 / 1.6
2.5 Return roller 108 x 1400L
2.6 Impact roller 108 x 1400L
2.7 Carrying idler - 108 mmD x 480mmL
2.8 V-belt
QUANTITY PRICE

Conveyor Calculation

Uploaded by

Copyright:

Available Formats

Conveyor Calculation

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Conveyor Calculation

Uploaded by

Copyright:

Available Formats

Design Considerations

 Characteristics and Conveyability of Bulk Materials

PROJECT : BY PASS CONVEYOR

Belt width 1800 mm Friction Factor (f)

P1 = Power required to move empty belt (kW) Pt

P2 = Power required to move load on level (kW)

P3 = Power to Lift load (kW) P

Effective tension (Te) = 6120 x P

Slope Tension (T3) = W1 ( H +/- f x L ) BELT WEIGHT STANDART (W1)

Sag Tension (T4) = 50/8 x Lr x W1 RETURN IDLER SPACING (Lr)

Counter Weight Calculation (Wt)~ 2 x T2 = 19075.58 kg Choise the Larger Tension

= Power to move Tripper (kW)

Infeed to the receiving hopper;

Belt Speed : 600 fpm

Surcharge angle of The

BELT CPONVEYOR PARAMETER

Belt Speed : 600 fpm

Belt Weight(WB : 42 inch

Design Belt Speed(Vee) : fpm

You might also like