Manual de Utilizare

HDCVI
Bullet Camera Lite

User’s Manual
V1.0.0
Foreword
General
This user’s manual (hereinafter referred to be "the Manual") introduces the functions,
installation, and operations of the camera.
Safety Instructions
The following categorized signal words with defined meaning might appear in the Manual.
Signal Words Meaning
Indicates a medium or low potential hazard which, if not avoided,

WARNING could result in slight or moderate injury.
Indicates a potential risk which, if not avoided, could result in

property damage, data loss, lower performance, or unpredictable
CAUTION
result.
TIPS Provides methods to help you solve a problem or save you time.
Provides additional information as the emphasis and supplement

NOTE
to the text.
Revision History
No. Version Revision Content Release Time

1 V1.0.0 First Release. June 8, 2018
Privacy Protection Notice
As the device user or data controller, you might collect personal data of others' such as face,
fingerprints, car plate number, Email address, phone number, GPS and so on. You need to be
in compliance with the local privacy protection laws and regulations to protect the legitimate
rights and interests of other people by implementing measures include but not limited to:
providing clear and visible identification to inform data subject the existence of surveillance
area and providing related contact.
About the Manual
 The Manual is for reference only. If there is inconsistency between the Manual and the
actual product, the actual product shall prevail.
 We are not liable for any loss caused by the operations that do not comply with the Manual.
 The Manual would be updated according to the latest laws and regulations of related
regions. For detailed information, see the paper manual, CD-ROM, QR code or our official
Foreword I
website. If there is inconsistency between paper manual and the electronic version, the
electronic version shall prevail.
 All the designs and software are subject to change without prior written notice. The product
updates might cause some differences between the actual product and the Manual. Please
contact the customer service for the latest program and supplementary documentation.
 There still might be deviation in technical data, functions and operations description, or
errors in print. If there is any doubt or dispute, please refer to our final explanation.
 Upgrade the reader software or try other mainstream reader software if the Guide (in PDF
format) cannot be opened.
 All trademarks, registered trademarks and the company names in the Manual are the
properties of their respective owners.
 Please visit our website, contact the supplier or customer service if there is any problem
occurred when using the device.
 If there is any uncertainty or controversy, please refer to our final explanation.
Foreword II
Important Safeguards and Warnings
Electrical Safety
 All installation and operation should conform to your local electrical safety codes.
 The power source shall conform to the requirement of the Safety Extra Low Voltage (SELV)
standard, and supply power with rated voltage which conforms to Limited power Source
requirement according to IEC60950-1. Please note that the power supply requirement is
subject to the device label.
 A readily accessible disconnect device shall be incorporated in the building installation
wiring.
 Make sure if the camera power adapter meets the camera operating voltage requirement
before powering up the device (The material and length of the power cable might influence
the device voltage).
 Prevent the power cable from being trampled or pressed, especially the plug, power socket
and the junction extruded from the device.
 We assume no liability or responsibility for all the fires or electrical shock caused by
improper handling or installation.
Environment
 Do not aim the device at strong light to focus, such as lamp light and sun light.
 Transport, use and store the device within the range of allowed humidity and temperature.
 Keep the camera away from water or other liquid to avoid damages to the internal
components.
 Keep sound ventilation to avoid heat accumulation.
 Heavy stress, violent vibration or water splash are not allowed during transportation,
storage and installation.
 Pack the device with standard factory packaging or the equivalent material when
transporting the device.
 It is recommended to use the device together with lightning arrester to improve lightning
protection effect.
 It is recommended to ground the device to enhance reliability.
 It is recommended to use qualified video transmission cable to improve video quality. It is
recommended to use RG59 coaxial cable or higher standard.
 Use standard components or accessories provided by manufacturer and make sure the
device is installed and maintained by professional engineers.
Important Safeguards and Warnings III

 The surface of the image sensor should not be exposed to laser beam radiation in an
environment where a laser beam device is used.
 Do not provide two or more power supply sources for the device; otherwise it might
damage the device.
 When the camera is in the condition of PoC power supply, do not connect any other device
between the camera and PoC transceiver including UTC, Balun, optical transceiver,
distributor and convertor and so on; otherwise, the device might get burned.
 PoC supply voltage is up to 52V. Do not dismantle the device during normal operation;
otherwise it might cause danger to both device and users due to high voltage.
Important Safeguards and Warnings IV

Regulatory Information
FCC Information
Changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
FCC conditions:
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
 This device may not cause harmful interference.
 This device must accept any interference received, including interference that may cause
undesired operation.
FCC compliance:
This equipment has been tested and found to comply with the limits for a digital device,
pursuant to part 15 of the FCC Rules. This equipment generate, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the guide, may cause
harmful interference to radio communication.
 For class A device, these limits are designed to provide reasonable protection against
harmful interference in a commercial environment. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
 For class B device, these limits are designed to provide reasonable protection against
harmful interference in a residential installation. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
 Reorient or relocate the receiving antenna.
 Increase the separation between the equipment and receiver.
 Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
 Consult the dealer or an experienced radio/TV technician for help.
Regulatory Information V
Table of Contents
Foreword .................................................................................................................................................... I
1 Introduction............................................................................................................................................ 1
1.1 General.......................................................................................................................................... 1
1.2 Features ........................................................................................................................................ 1
2 Design..................................................................................................................................................... 2
2.1 Dimension ..................................................................................................................................... 2
2.2 Cable ............................................................................................................................................. 4
3 Installation.............................................................................................................................................. 6
3.1 Installing Model A (1) and Model A (2) .......................................................................................... 6
3.2 Installing Model B .......................................................................................................................... 7
3.3 Installing Model C.......................................................................................................................... 8
3.4 Installing Model D.......................................................................................................................... 9
3.5 Installing Model E ........................................................................................................................ 10
3.6 Installing Model F .........................................................................................................................11
3.7 Installing Model G ....................................................................................................................... 12
3.8 Installing Model H........................................................................................................................ 13
3.9 Installing Model I (1) and Model I (2) .......................................................................................... 14
3.10 Installing Model J ...................................................................................................................... 15
3.11 Installing Model K (1) and Model K (2)...................................................................................... 16
3.12 Installing Model L ...................................................................................................................... 17
4 General Configuration ........................................................................................................................ 19
4.1 Opening Main Menu.................................................................................................................... 19
4.2 Setting Audio Input ...................................................................................................................... 20
4.3 Operating OSD Menu ................................................................................................................. 21
5 Maintenance ......................................................................................................................................... 23
Table of Contents VI
1 Introduction
1.1 General
This series of products comply with the HDCVI standard and support the transmission of video
and control signal over coaxial cable. They produce video signal with megapixel resolution and
require XVR device that comply with the HDCVI standard to achieve high speed, long distance,
and zero lag transmission of the signal. They are applicable to cover the high definition
monitoring needs for locations with low ambient light, including road, warehouse, underground
parking lot, bar, pipeline, and gas station.
1.2 Features
 720p series support over 800 meter real-time transmission of video and control signal from
RG59 cable; for 1080p and above, the distance is 500 meter.
 Support adjusting zoom and focus on XVR with motorized varifocal lens (available on
select model).
 Excellent low-light performance with IR or night vision technology.
 Configuring devices easily with OSD menu.
 Support switching between HD and SD outputs.
Introduction 1
2 Design
2.1 Dimension
Figure 2-1 Model A (1) (mm [in.])
Figure 2-2 Model A (2) (mm [in.])
Figure 2-3 Model B (mm [in.])
Figure 2-4 Model C (mm [in.])
Figure 2-5 Model D (mm [in.])
Design 2
Figure 2-6 Model E (mm [in.])
Figure 2-7 Model F (mm [in.])
Figure 2-8 Model G (mm [in.])
Figure 2-9 Model H (mm [in.])
Figure 2-10 Model I (1) (mm [in.])
Figure 2-11 Model I (2) (mm [in.])
Design 3
Figure 2-12 Model J (mm [in.])
Figure 2-13 Model K (1) (mm [in.])
Figure 2-14 Model K (2) (mm [in.])
Figure 2-15 Model L (mm [in.])
2.2 Cable
Cable type might vary with different cameras, and the actual product shall prevail.
Design 4
Figure 2-16 Cable list
For more information about cable ports, see Table 2-1; for the operation method of ④ (DIP
switch), see Table 2-2.
Table 2-1 Cable function

No. Port Name Function
① 12V DC Inputs 12V DC power. Please be sure to supply power as instructed in the
Power Input Manual.
Device abnormity or damage could occur if power is not supplied correctly.

② Video Connects to XVR to output video signal.
Output
③ Audio Input Connects to sound-pick-up devices to receive audio signal.
④ DIP Switch Dial switches to change output mode. Switch up indicates "ON", switch down
indicates "OFF."
Table 2-2 DIP switch operation

Switch1 Switch2 Output Mode
OFF OFF CVI
ON ON CVBS
ON OFF AHD
OFF ON TVI
Design 5
3 Installation
Make sure the mounting surface is strong enough to hold at least three times of the camera
weight.
The following figures are for reference only, and the actual product shall prevail.
3.1 Installing Model A (1) and Model A (2)

Figure 3-1 Model A (1) and Model A (2) installation
Table 3-1 Installation item list

No. Item No. Item
① Device ② Self-tapping screw
③ Expansion bolt ④ Mounting surface
Step 1 Confirm the position of screw holes (and the cable outlet hole if it needs to go through
the mounting surface④) and drill them on the mounting surface④, and then insert the
expansion bolts③ in the screw holes.
Step 2 Align the screw holes on the bracket to those on the mounting surface④, and then pull
the cable out through mounting surface or the side cable tray. Attach the bracket to the
mounting surface④ with the self-tapping screws②.
Step 3 Connect the device① to power source and the XVR device, and then the live view
screen is displayed.
Step 4 The adjustment way of model A (1) is different from which of model A (2).
 For Model A (1)
1) Loosen the locking screws and aim the lens to the ideal angle, and then fasten
them, see Figure 3-2.
Installation 6
Figure 3-2 Model A (1) and Model A (2) adjustment
2) In the PTZ setting interface (Figure 4-5), click + or – at Zoom and Focus to adjust
the zoom and focus until you get clear image.
 For Model A (2)
1) Loosen the locking screws and aim the lens to the ideal angle, see Figure 3-2.
2) Open the bottom cover, and then twist to loosen the zoom and focus levers, turn
them left or right to adjust the focus and zoom until you get clear image, see Figure
3-3.
Figure 3-3 Model A (2) image adjustment
3) Lock the levers and bottom cover, and then fasten the locking screws.
3.2 Installing Model B

Figure 3-4 Model B installation

No. Item No. Item
Installation 7
No. Item No. Item
Step 3 Connect the device① to power source and the XVR device, and the live view screen is
displayed.
Step 4 Loosen the locking screws and aim the lens to the ideal angle, and then fasten them,
see Figure 3-5.
Figure 3-5 Model B adjustment
3.3 Installing Model C

Figure 3-6 Model C installation

No. Item No. Item
Installation 8
displayed.
see Figure 3-7.
Figure 3-7 Model C adjustment
3.4 Installing Model D

Figure 3-8 Model D installation

No. Item No. Item
displayed.
Step 4 Loosen the locking screw and aim the lens to the ideal angle, and then fasten it, see
Figure 3-9.
Installation 9
Figure 3-9 Model D adjustment
3.5 Installing Model E

Figure 3-10 Model E installation

No. Item No. Item
displayed.
see Figure 3-11.
Figure 3-11 Model E adjustment
Installation 10
3.6 Installing Model F
Figure 3-12 Model F installation

No. Item No. Item
displayed.
Step 4 Loosen the locking screw and aim the lens to the ideal angle, and then fasten it, see
Figure 3-13.
Figure 3-13 Model F adjustment
Installation 11
3.7 Installing Model G
Figure 3-14 Model G installation

No. Item No. Item
displayed.
see Figure 3-15.
Figure 3-15 Model G adjustment
Installation 12
3.8 Installing Model H
Figure 3-16 Model H installation

No. Item No. Item
displayed.
see Figure 3-17.
Figure 3-17 Model H adjustment
Installation 13
3.9 Installing Model I (1) and Model I (2)
Figure 3-18 Model I (1) and Model I (2) installation

No. Item No. Item
displayed.
Step 4 The adjustment way of model I (1) is different from which of model I (2).
 For Model I (1)
Figure 3-19 Model I (1) and Model I (2) adjustment
 For Model I (2)
Installation 14
3-20.
Figure 3-20 Model I (2) image adjustment
3.10 Installing Model J

Figure 3-21 Model J installation

No. Item No. Item
displayed.
see Figure 3-22.
Installation 15
Figure 3-22 Model J adjustment
3.11 Installing Model K (1) and Model K (2)

Figure 3-23 Model K (1) and Model K (2) installation

No. Item No. Item
displayed.
Step 4 The adjustment way of model K (1) is different from which of model K (2).
 For Model K (1)
Installation 16
Figure 3-24 Model K (1) and Model K (2) adjustment
 For Model K (2)
3-25.
Figure 3-25 Model K (2) image adjustment
3.12 Installing Model L

Figure 3-26 Model L installation

No. Item No. Item
Installation 17
displayed.
see Figure 3-27.
Figure 3-27 Model L adjustment
Installation 18
4 General Configuration
Power up the camera and connect it to the XVR device with coaxial cable, and then the live
view screen is displayed. The following instructions will guide you to configure your camera.
 The number of the coaxial port on XVR will display at the lower left corner of each window
to indicate the corresponding camera.
 Interfaces of different XVR might vary, and the actual product shall prevail.
4.1 Opening Main Menu

Step 1 In the live view screen interface, right-click anywhere on the screen.
The shortcut menu is displayed. See Figure 4-1.
Figure 4-1 Shortcut menu
Step 2 Click Main Menu.

The Main Menu interface is displayed. See Figure 4-2.
General Configuration 19
Figure 4-2 Main menu interface
Right-click anywhere on the screen to return to the previous interface until it goes back to the
live view screen.
4.2 Setting Audio Input
Audio signal acquisition is available on select models.

Step 1 In the Main Menu interface (Figure 4-2), select CAMERA > ENCODE > Encode.
The Encode setting interface is displayed. See Figure 4-3.
Figure 4-3 Encode setting interface
Step 2 In the Channel list, select the camera that you want to configure according to the
coaxial port number.
Step 3 In the Main Stream column, click More Setting.
The More Setting interface is displayed, see Figure 4-4.
Figure 4-4 More setting interface
Step 4 In the More Setting interface, you can configure the audio settings.
 Enable Audio Encode function.
 In the Audio Format list, leave to the default.
 In the Audio Source list, select HDCVI.
Step 5 Click Save to save the settings.
The Encode setting interface is displayed (Figure 4-3).
Step 6 In the Encode setting interface (Figure 4-3), click Apply.
4.3 Operating OSD Menu
The OSD menus of different cameras might vary, and the actual product shall prevail.
Step 1 In the live view screen interface, right-click within the live view window of the camera
that you want to configure.
The shortcut menu (Figure 4-1) is displayed.
Step 2 Click PTZ.
The PTZ setting interface is displayed. See Figure 4-5.
Figure 4-5 PTZ setting interface
Step 3 Click to see more options. See Figure 4-6.
Figure 4-6 PTZ setting options
Step 4 Click .
The MENU OPERATION panel is displayed. See Figure 4-7.
The OSD menu of the corresponding camera is displayed on the live view screen.
Figure 4-7 Menu Operation panel
For the function of the buttons in the MENU OPERATION panel, see Table 4-1.
Table 4-1 Menu Operation panel function

Button Function Button Function
Enter or confirm an item , Select item
Exit OSD menu Change item value

,
If there is " " as the value of an OSD item, click Enter to go to the next level of this item. Click
Return to go back to the previous level. Clicking Cancel is to exit OSD menu without saving the
modifications.
5 Maintenance
In order to maintain the image quality and proper functioning of the device, please read the
following maintenance instructions carefully and hold rigid adherence.
Disassembly and Desiccant Replacement
 Carefully follow the instructions in the manual when performing any disassembly operation
about the device; otherwise, it might cause water leakage or poor image quality due to
unprofessional disassemble.
 Please contact after-sale service for desiccant replacement if there is condensed fog found
on the lens after unpacking or when the desiccant turns green. (Not all models are included
with the desiccant).
Maintaining Lens and Mirror Surface
 The lens and mirror surface are covered with antireflection coating, which could be
contaminated or damaged and result in lens scratches or haze image when being touched
with dust, grease, fingerprints and other similar substances.
 Do not touch the image sensor directly (CCD or CMOS). Dust and dirt could be removed
with air blower, or you can wipe the lens gently with soft cloth that moistened with alcohol.
Maintaining Device Body
 Device body can be cleaned with soft dry cloth, which can also be used to remove
stubborn stains when moistened with mild detergent.
 To avoid possible damage on device body coating which could cause performance
decrease, do not use volatile solvent such as alcohol, benzene, diluent and so on to clean
the device body, nor can strong, abrasive detergent be used.
Maintenance 23

Manual de Utilizare

Uploaded by

Copyright:

Available Formats

Manual de Utilizare

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Manual de Utilizare

Uploaded by

Copyright:

Available Formats

HDCVI

Bullet Camera Lite

Indicates a medium or low potential hazard which, if not avoided,

Indicates a potential risk which, if not avoided, could result in

Provides additional information as the emphasis and supplement

No. Version Revision Content Release Time

Privacy Protection Notice

About the Manual

Important Safeguards and Warnings III

Important Safeguards and Warnings IV

Figure 2-2 Model A (2) (mm [in.])

Figure 2-3 Model B (mm [in.])

Figure 2-4 Model C (mm [in.])

Figure 2-5 Model D (mm [in.])

Figure 2-7 Model F (mm [in.])

Figure 2-8 Model G (mm [in.])

Figure 2-9 Model H (mm [in.])

Figure 2-10 Model I (1) (mm [in.])

Figure 2-11 Model I (2) (mm [in.])

Figure 2-13 Model K (1) (mm [in.])

Figure 2-14 Model K (2) (mm [in.])

Figure 2-15 Model L (mm [in.])

Table 2-1 Cable function

Device abnormity or damage could occur if power is not supplied correctly.

Table 2-2 DIP switch operation

3.1 Installing Model A (1) and Model A (2)

Table 3-1 Installation item list

3.2 Installing Model B

Table 3-2 Installation item list

3.3 Installing Model C

Table 3-3 Installation item list

3.4 Installing Model D

Table 3-4 Installation item list

3.5 Installing Model E

Table 3-5 Installation item list

Table 3-6 Installation item list

Table 3-7 Installation item list

Table 3-8 Installation item list

Table 3-9 Installation item list

3.10 Installing Model J

Table 3-10 Installation item list

3.11 Installing Model K (1) and Model K (2)

Table 3-11 Installation item list

3.12 Installing Model L

Table 3-12 Installation item list

4.1 Opening Main Menu

Step 2 Click Main Menu.

4.2 Setting Audio Input

Audio signal acquisition is available on select models.

4.3 Operating OSD Menu

Step 3 Click to see more options. See Figure 4-6.

Table 4-1 Menu Operation panel function

Enter or confirm an item , Select item

Exit OSD menu Change item value

Disassembly and Desiccant Replacement

Maintaining Lens and Mirror Surface

Maintaining Device Body

You might also like