For the latest prices, please check AutomationDirect.com.

Ethernet Analog PLC

C0-12DD2E-D $179.00
4 DC Input (Sink/Source)/ 4 Sourcing DC Output;
2 Analog Voltage/Current Input
2 Analog Voltage/Current Output Micro PLC

Wiring Diagram
C0-12DD2E-D
24VDC
C1
X1
See Discrete I/O Specifications

+
X2
PWR RUN
R UN Inputs (X1 – X4)

+
X3
RUN X4
ERR STOP
S TOP V1
Y1 L 24
PORT1
VDC
Y2 L See Discrete I/O Specifications
+

LNK/ACT
L
ETHER Y3 Outputs (Y1 – Y4)
NET Y4 L
100MBIT
CO
AD1V Transmitter 0-5V
PORT2 See Analog I/O Specifications -
AD1 I Transmitter 4-20mA
TX2
AD2V Transmitter 0-5V
Voltage & Current
RX2
AD2 I Transmitter 4-20mA
Input (AD1V – AD2I)
RS-232
RS 232
ACOM
RS-485
RS-
-485
485
5 DA1V
PO
ORT3
PORT3
See Analog I/O Specifications -
TX3
TX
X3
+
_
DA1 I
Voltage & Current
DA2V
RX
X3
RX3
LG
G DA2 I Output (DA1V – DA2I)
+

Transmitter
P/S

NOTE: There are no ZIPLink pre-wired PLC connection cables and modules for the Analog
PLCs (cannot mix discrete I/O and analog I/O signals in a ZIPLink cable).

NOTE: When using Ethernet Analog PLCs, you must use CLICK programming software
version V2.20 or later.

IMPORTANT: use only one terminal (voltage or current) per channel. You
must also select the analog type (voltage or current) in the CPU built-in I/O
setup in the CLICK programming software
(pull-down menu Setup > CPU Built-in I/O Setup).

General Specifications
Current Consumption at 24VDC 140mA
Terminal Block Replacement Part No. C0-16TB
Weight 5.08 oz (144g)

tCLP-62 CLICK PLCs 1-800-633-0405

 For the latest prices, please check AutomationDirect.com.

Ethernet Analog PLC

C0-12DD2E-D (cont’d)
X1 - X4
Discrete I/O Specifications - Inputs Equivalent Discrete Input Circuit 3.3 V

Inputs per Module 4 (Sink/Source) Internal Module Circuitry

Operating Voltage Range 24VDC 24 VDC INPUT

Optical Isolator
Input Voltage Range 21.6–26.4 VDC
+
X1-X4 VCC

Input Current Typ 6.5 mA @ 24VDC +

Maximum Input Current 7mA @ 26.4 VDC C1 GND

Input Impedance 3.9 kq @ 24VDC COM

ON Voltage Level > 19VDC

OFF Voltage Level < 2VDC C0-12DD2E-D Temperature Derating Chart
Minimum ON Current 4.5 mA
4
Maximum OFF Current 0.5 mA Inputs
OFF to ON Response Typ 3µs, Max 5µs 3

ON to OFF Response Typ 1µs, Max 3µs

Points
2
Status Indicators Logic Side (4 points, green LED)
1
Commons 1 (4 points/common)
0
0 10 20 30 40 50 55 °C
32 50 68 85 104 122 131 °F
Ambient Air Temperature (°C/°F)

Y1 - Y4
Discrete I/O Specifications - Outputs Equivalent Discrete Output Circuit

Outputs per Module 4 (Source) Internal Module Circuitry 3.3 V

24VDC
+ +V

Operating Voltage Range 24VDC Optical Isolator

VCC
Output Voltage Range 19.2–30 VDC
Maximum Output Current 0.1 A/point , 0.4 A/common L
Y1-Y4
GND
Minimum Output Current 0.2 mA 0V
Maximum Leakage Current 0.1mA @ 30VDC CO

On Voltage Drop 0.5 VDC@ 0.1 A

Maximum Inrush Current 150mA for 10ms C0-12DD2E-D Temperature Derating Chart
OFF to ON Response < 5µs 4
ON to OFF Response < 5µs Outputs
3
Status Indicators Logic Side (4 points, red LED)
Points

Commons 1 (4 pts or 1 pt/common) 2

0
0 10 20 30 40 50 55 °C
32 50 68 85 104 122 131 °F
Ambient Air Temperature (°C/°F)

www.automationdirect.com/click-plc CLICK PLCs tCLP-63

 For the latest prices, please check AutomationDirect.com.

Ethernet Analog PLC

C0-12DD2E-D (cont’d)
AD1V - AD2V AD1I - AD2I
Analog Specifications - Voltage Input Analog Specifications - Current Input
Inputs per Module 2 (voltage/current selectable) Inputs per Module 2 (voltage/current selectable)
Input Range 0–5 VDC Input Range 4–20 mA (sink)
Resolution 12 bit Resolution 12 bit
Conversion Time 50ms Conversion Time 50ms
Input Impedance 20kq Input Impedance 125q
Input Stability ±2 LSB maximum Input Stability ±2 LSB maximum
Full-Scale Calibration Error ±2% maximum Full-Scale Calibration ±2% maximum
Offset Calibration Error ±25mV maximum Error
Accuracy vs. Temperature Offset Calibration Error ±0.1 mA maximum
±100ppm / °C maximum Accuracy vs. Temperature ±100ppm / °C maximum
Error
Error
Analog Voltage Input Circuit
Analog Current Input Circuit
Internal Module Circuitry

ADxV 10kΩ Internal Module Circuitry

Voltage A/D
Transmitter Converter ADxI
0V 10kΩ
Current A/D
ACOM Transmitter Converter
0V 125Ω
+ ACOM
Transmitter
P/S +
Transmitter
P/S

DA1V - DA2V DA1I - DA2I

Analog Specifications - Voltage Output Analog Specifications - Current Output
Outputs per Module 2 (voltage/current selectable) Outputs per Module 2 (voltage/current selectable)
Output Range 0–5 VDC Output Range 4–20 mA (sink)
Resolution 12 bit Resolution 12 bit
Conversion Time 1ms Conversion Time 1ms
2kq minimum Loop Supply Voltage DC 18–30 V
Load Impedance (output current 2.5 mA maximum) 250q
Full-Scale Calibration Error ±2% maximum Load Power Supply:
Offset Calibration Error ±25mV maximum Load Impedance DC 18V: 600q maximum
Accuracy vs. Temperature ±100ppm / °C maximum DC 24V: 900q maximum
Error DC 30V: 1200q maximum
Full-Scale Calibration Error ±2% maximum
Analog Voltage Output Circuit Offset Calibration Error ±25mA maximum
Accuracy vs. Temperature Error ±100ppm / °C maximum
Internal Module Circuitry
DAxV Analog Current Output Circuit
Load D/A
2kΩ minimum 0V Converter Internal Module Circuitry
ACOM DAxI
Load +
– D/A
250Ω Converter
typical 0V 100Ω
ACOM

+
Transmitter P/S
18-30 VDC

tCLP-64 CLICK PLCs 1-800-633-0405

 For the latest prices, please check AutomationDirect.com.

Choosing Expansion I/O Modules

Analog I/O Modules
(continued)
Analog Combo I/O Modules

C0-4AD2DA-1 C0-4AD2DA-2
0-20mA In 0-10V
4-20mA Out

CH1 CH1
0V 0V

INPUT

INPUT
CH2 CH2
0V 0V

CH3 CH3
0V 0V

CH4 CH4
0V 0V

CH1 CH1
0V 0V

OUTPUT

OUTPUT
CH2 CH2
0V 0V

24V 24V
0V 0V

C0-4AD2DA-1 C0-4AD2DA-2

Analog Combo I/O Modules

External Power
Part Number Analog Input Type Analog Output Type Required
4 channel, current (0-20 mA), 2 channel, current sourcing
C0-4AD2DA-1 13 bit (4-20 mA), 12 bit 24 VDC
4 channel, voltage (0-10 V), 4 channel, voltage
C0-4AD2DA-2 13 bit (0-10 V), 12 bit 24 VDC

General Specifications General Specifications

Power Input Voltage Range 20–28 VDC
For All CLICK PLC Maximum Power Consumption 5W (No 5V use from communication port)
Products Maximum Inrush Current 30A (less than 1ms)

These general specifications apply to all Acceptable External Power Drop Max 10ms
Analog, analog combo I/O modules only:
CLICK PLCs, optional I/O modules, and 32°F to 140°F (0°C to 60°C);
optional power supply products. Please Operating Temperature All other modules:
32°F to 131°F (0°C to 55°C),
refer to the appropriate I/O temperature IEC 60068-2-14 (Test Nb, Thermal Shock)
derating charts under both the PLC and –4°F to 158°F (–20°C to 70°C)
I/O module specifications to determine IEC 60068-2-1 (Test Ab, Cold)
Storage Temperature IEC 60068-2-2 (Test Bb, Dry Heat)
best operating conditions based on the IEC 60068-2-14 (Test Na, Thermal Shock)
ambient temperature of your particular Ambient Humidity 30% to 95% relative humidity (non–condensing)
application. Environmental Air No corrosive gases. Environmental pollution level is 2 (UL840)
MIL STD 810C, Method 514.2, EC60068-2-6
Vibration JIS C60068-2-6 (Sine wave vibration test)
Shock MIL STD 810C, Method 516.2, IEC60068-2-27, JIS C60068-2-27
Comply with NEMA ICS3-304, Impulse noise 1μs, 1000V
EN61000-4-2 (ESD), EN61000-4-3 (RFI), EN61000-4-4 (FTB)
Noise Immunity EN61000-4-5 (Surge), EN61000-4-6 (Conducted)
EN61000-4-8 (Power frequency magnetic field immunity)
RFI: No interference measured at 150 and 450 MHz (5w/15cm)
Emissions EN55011:1998 Class A
Agency Approvals UL508 (File No. E157382, E316037); CE (EN61131-2)
Other RoHS

www.automationdirect.com/click-plc CLICK PLCs tCLP-27

 For the latest prices, please check AutomationDirect.com.

CLICK Specifications

PLC Unit Specifications

Basic, Standard and Analog PLC Unit Specifications
Basic PLC Standard PLC Analog PLC
Control Method Stored Program/Cyclic Stored Program/Cyclic Stored Program/Cyclic
execution method execution method execution method
I/O Numbering System Fixed in Decimal Fixed in Decimal Fixed in Decimal
Ladder Memory (steps) 8000 8000 8000
Total Data Memory (words) 8000 8000 8000
Contact Execution (boolean) < 0.6us < 0.6us < 0.6us
Typical Scan (1k boolean) 1-2 ms 1-2 ms 1-2 ms
RLL Ladder Style Programming Yes Yes Yes
Run Time Edits No No No
Scan Variable / fixed Variable / fixed Variable / fixed
CLICK Programming Software for Yes Yes Yes
Windows
Yes (two RS-232 ports and Yes (two RS-232 ports and
Built-in Communication Ports Yes (two RS-232 ports) one RS-485 port) one RS-485 port)
FLASH Memory Standard on PLC Standard on PLC Standard on PLC
Built-in Discrete I/O points 8 inputs, 6 outputs 8 inputs, 6 outputs 4 inputs, 4 outputs
Built-in Analog I/O Channels No No 2 inputs, 2 outputs
Number of Instructions Available 21 21 21
Control Relays 2000 2000 2000
System Control Relays 1000 1000 1000
Timers 500 500 500
Counters 250 250 250
Interrupt Yes (external: 8 / timed: 4) Yes (external: 8 / timed: 4) Yes (external: 4 / timed: 4)
Subroutines Yes Yes Yes
For/Next Loops Yes Yes Yes
Math (Integer and Hex) Yes Yes Yes
Drum Sequencer Instruction Yes Yes Yes
Internal Diagnostics Yes Yes Yes
Password Security Yes Yes Yes
System Error Log Yes Yes Yes
User Error Log No No No
Memory Backup Super Capacitor Super Capacitor + Battery Super Capacitor + Battery
Yes (battery sold separately; Yes (battery sold separately;
Battery Backup No
part # D2-BAT-1) part # D2-BAT-1)
Calendar/Clock No Yes Yes
I/O Terminal Block Replacement ADC p/n C0-16TB ADC p/n C0-16TB ADC p/n C0-16TB
Communication Port & Terminal
N/A ADC p/n C0-3TB ADC p/n C0-3TB
Block Replacement
24 VDC Power Terminal Block ADC p/n C0-4TB ADC p/n C0-4TB ADC p/n C0-4TB
Replacement

tCLP-28 CLICK PLCs 1-800-633-0405

 For the latest prices, please check AutomationDirect.com.

CLICK Specifications
PLC Units Specifications (continued)
Ethernet Basic, Standard and Analog PLC Unit Specifications
Ethernet Basic PLC Ethernet Standard PLC Ethernet Analog PLC
Control Method Stored Program/Cyclic execution method Stored Program/Cyclic execution method Stored Program/Cyclic execution method
I/O Numbering System Fixed in Decimal Fixed in Decimal Fixed in Decimal
Ladder Memory (steps) 8000 8000 8000
Total Data Memory (words) 8000 8000 8000
Contact Execution (boolean) < 0.2 µs < 0.2 µs < 0.2 µs
Typical Scan (1k boolean) < 1ms < 1ms < 1ms
RLL Ladder Style Programming Yes Yes Yes
Run Time Edits Yes Yes Yes
Scan Variable / fixed Variable / fixed Variable / fixed
CLICK Programming Software for Yes Yes Yes
Windows
Yes (one Ethernet port and Yes (one Ethernet port, one RS-232 port and Yes (one Ethernet port, one RS-232 port and
Built-in Communication Ports one RS-232 port) one RS-485 port) one RS-485 port)
FLASH Memory Standard on PLC Standard on PLC Standard on PLC
Built-in Discrete I/O points 8 inputs, 6 outputs 8 inputs, 6 outputs 4 inputs, 4 outputs
Built-in Analog I/O Channels No No 2 or 4 inputs; 2 outputs
Number of Instructions Available 21 21 21
Control Relays 2000 2000 2000
System Control Relays 1000 1000 1000
Timers 500 500 500
Counters 250 250 250
Interrupt Yes (external: 8 / timed: 4) Yes (external: 8 / timed: 4) Yes (external: 8 / timed: 4)
Subroutines Yes Yes Yes
For/Next Loops Yes Yes Yes
Math (Integer and Hex) Yes Yes Yes
Drum Sequencer Instruction Yes Yes Yes
Internal Diagnostics Yes Yes Yes
Password Security Yes Yes Yes
System Error Log Yes Yes Yes
User Error Log No No No
Memory Backup Super Capacitor + Battery Super Capacitor + Battery Super Capacitor + Battery
Battery Backup Yes (battery part # D2-BAT-1) Yes (battery part # D2-BAT-1) Yes (battery part # D2-BAT-1)
Calendar/Clock Yes Yes Yes
I/O Terminal Block Replacement ADC p/n C0-16TB ADC p/n C0-16TB ADC p/n C0-16TB
Communication Port & Terminal N/A ADC p/n C0-3TB ADC p/n C0-3TB
Block Replacement
24 VDC Power Terminal Block ADC p/n C0-4TB ADC p/n C0-4TB ADC p/n C0-4TB
Replacement

www.automationdirect.com/click-plc CLICK PLCs tCLP-29

 For the latest prices, please check AutomationDirect.com.

CLICK Specifications
PLC Features
Basic PLCs Standard PLCs

Mounting Mounting
Tab Tab

Sliding Sliding
Latch Latch
PLC Mode PLC Mode C0-01DD1-D

Switch Switch
8 Discrete 8 Discrete
Input Input
LED Status Points LED Status Points
Indicators
PWR
Indicators RUN
ERR

PORT1
TX1
RX1
Communication
Ports
Communication
TX2

6 Discrete RX2 6 Discrete

Ports PORT2 Output
Output
Points RS-485
Points
PORT3

TX3
RX3

Sliding Sliding
Latch Latch
Power Power
Terminal Mounting Terminal Mounting
24V Tab 24V Tab
0V 0V
N.C. N.C.
G G

Analog PLCs

Mounting Bottom of PLC

Tab (Same on all models)

Sliding
Latch
PLC Mode C0-02DD1-D

Switch C1
X1
4 Discrete
X2
Inputs
X3 Power
LED Status PWR X4 Terminal
al
Indicators RUN C2
ERR Y1 4 Discrete 24V
Y2 Outputs 0V
PORT1
TX1
Y3
Y4
N.C.
RX1 +V G
AD1V 2 Analog
Communication
TX2
RX2
AD1II
AD1 Inputs
AD2V
Ports PORT2
AD2II
AD2
ACOM
PORT3
RS-485
DA1V 2 Analog
TX3 DA1II
DA1 Outputs
RX3 DA2V
DA2II
DA2

Sliding
Latch
Power
Terminal Mounting
24V Tab
0V
N.C.
G

tCLP-30 CLICK PLCs 1-800-633-0405

 For the latest prices, please check AutomationDirect.com.

CLICK Specifications
PLC Features (continued)

Ethernet Basic PLCs Ethernet Standard PLCs

Mounting Mounting
Tab Tab

S
Sliding Sliding
Latch
L C0-11DD1E-D
C0-11DD1E-
Latch
C0-10DD1E-D
C0-10DD1E-
-D
D PLC Mode 01DD1-D
-D
PLC Mode C0-01DD1-D
C0-
C0 01DD1 D

Switch Switch C1
1
C1
X1 8 Discrete X1
1 8 Discrete
X2
2
Input
X2
2
Input
LED Status PWR RUN
RUN X3
3
Points LED Status PWR
RUN
RUN
RUN X3
3
Points
X4
4
Indicators
RUN R
PWR
X4
4
Indicators ERR STOP
STOP C2
2
RUN
ERR STOP
STOP C2
2
ERR
PORT1 X5
5
PORT1 X5
5
LNK/ACT X6
6
LNK/ACT X6
6
PO
PORT
ORT1
ORT1
PORT1
ETHER X7
7
ETHER X7
7
NET
TX
TX
X1
TX1 X8
8
NET X8
8 100MBIT
100MBIT RX
X
X1
RX1
Communication C3
3
Ports PORT2
C3
3 PORT2
X2
TX2 Y1
1
TX2
Y1 Communication TX2
Y2
2 6 Discrete
Y2
2 6 Discrete Ports
X
RX2
RX2
RX2
Y3
3 Output
PORT2
PORT2
RS 232
RS-232
Y3
3 Output
RS-232
RS 232
Y4
4
Points RS-485
R
RS-4
RS-485
S
S-4 85 5
485
Y4
4
Points
PO
PO RT3
PORT3
ORT
ORT3
T3 C4
4
C4
4
Y5
5 TX
X3
TX
TX33
+
_
Y5
5
Y6
6
Y6
6 RX
RX
X3
3
RX3
LG
G +V
V
+V
V

S
Sliding Sliding
Latch
L Latch
Power
wer Power
Terminal
rminal Mounting Terminal Mounting
24V Tab 24V Tab
0V 0V
N.C. N.C.
G G

Ethernet Analog PLCs

Bottom of Ethernet PLC
Mounting
Tab (Same on all models)

Sliding
PLC Mode C0-12DD1E-D Latch
Switch C1
X1 4 Discrete
X2
Inputs Power
LED Status PWR RUN
R UN X3

Indicators RUN X4 Terminal

al
ERR STOP
S TOP C2
PORT1 Y1 4 Discrete 24V
LNK/ACT Y2 Outputs 0V
ETHER Y3
NET Y4 N.C.
100MBIT
+V G
AD1V
PORT2 2 or 4 Analog
Communication TX2
AD1 I
AD2V Inputs
Ports RX2
AD2 I
RS-232
RS 232
ACOM
RS-485
RS-
-485
485
5 DA1V
PORT3
2 Analog
TX3
+
_
DA1 I
Outputs
DA2V
RX3
LG DA2 I

Sliding
Latch
Power
Terminal
Removeable Screw Type
24V Terminal Block
0V
N.C. Mounting
G Tab

www.automationdirect.com/click-plc CLICK PLCs tCLP-31

 For the latest prices, please check AutomationDirect.com.

CLICK Specifications
PLC LED Status Indicators
Basic CPUs
POWER LED (Green) Basic PLC
On Power Good
Off Power Failure

RUN LED (Green)

On PLC Run Mode
Initializing
Blink System INPUT LEDs (Green)
PLC Program On Input True
Off Mode
Off Input False
ERROR LED (RED)
Self Diagnostic
On Error
Blink Self Diagnostic
Warning
Off No Error OUTPUT LEDs (Red)
On Output True
TX & RX LED (Green)
Off Output False
On Comm Port Data Active
Off No Communication

Standard PLC
POWER LED (Green) Standard CPUs
On Power Good
Off Power Failure

RUN LED (Green) C0-01DD1-D

On PLC Run Mode

Initializing
Blink System
INPUT LEDs (Green)
PLC Program PWR
Off Mode RUN On Input True
ERR
Off Input False
ERROR LED (RED) PORT1

On Self Diagnostic TX1

Error RX1

Blink Self Diagnostic

Warning TX2
RX2
Off No Error PORT2 OUTPUT LEDs (Red)

PORT3
RS-485 On Output True
TX & RX LED (Green)
TX3 Off Output False
On Comm Port Data Active RX3

Off No Communication

Analog PLC
POWER LED (Green)
Analog CPUs
On Power Good
Off Power Failure

INPUT LEDs (Green)

RUN LED (Green) C0-02DD1-D
C1 On Input True
On PLC Run Mode X1

Initializing X2
Off Input False
Blink System X3

PLC Program PWR X4

Off Mode C2
RUN
OUTPUT LEDs (Red)
ERR Y1
Y2 On Output True
ERROR LED (RED) PORT1 Y3
Off Output False
On Self Diagnostic TX1 Y4
Error RX1 +V

Self Diagnostic
Blink Warning
AD1V
TX2 AD1 I
RX2 AD2V
Off No Error PORT2
AD2 I
ACOM
RS-485
PORT3 DA1V
TX & RX LED (Green)
TX3 DA1 I
On Comm Port Data Active RX3 DA2V
DA2 I
Off No Communication

tCLP-32 CLICK PLCs 1-800-633-0405

 For the latest prices, please check AutomationDirect.com.

CLICK Specifications
PLC LED Status Indicators
POWER LED (Green)
On Power Good Ethernet Basic PLC
Off Power Failure Ethernet Basic CPU
RUN LED (Green) C0-10DD1E-D
C0-10D D1E--D
D

On PLC Run Mode C1

Initializing X1
Blink System X2
PWR RUN
R X3
INPUT LEDs (Green)
PLC Program
Off Mode RUN X4
On Input True
ERR STOP
S C2
2
PORT1 X5 Off Input False
ERROR LED (RED) LNK/ACT X6
ETHER X7
On Self
Error
Diagnostic NET X8
100MBIT

Blink Self Diagnostic

Warning PORT2
C3
3
Y1
TX2
Off No Error RX2
Y2
OUTPUT LEDs (Red)
Y3
RS-232
RS 232
Y4 On Output True
LNK/ACT LED (Green) C4
4
Y5 Off Output False
On Connected to the network Y6
+V
V
Blink Communicating

Off Disconnected from the network

100MBIT LED (Orange) TX & RX LED (Green)

On Comm Port Data Active
On Communicating at 100Mbps
POWER LED (Green) Ethernet Standard PLC
Communicating at 10Mbps or Off No Communication
Off disconnected from the network On Power Good Standard Ethernet PLC
Off Power Failure
C0-11DD1E-D
C0-11D D1E--D
D
RUN LED (Green)
C1
1
On PLC Run Mode X1
X2
2
Initializing INPUT LEDs (Green)
Blink System PWR RUN
RUN X3
3
RUN X4
4
On Input True
PLC Program ERR STOP
STOP C2
2
Off Mode
PORT1 X5
5 Off Input False
LNK/ACT X6
6
ETHER X7
7
ERROR LED (RED) NET X8
8
100MBIT
Self Diagnostic
On Error C3
3
PORT2

Blink Self Diagnostic Y1

TX2
Warning Y2
2
RX2
Y3
3 OUTPUT LEDs (Red)
RS-232
RS 232
Off No Error Y4
4
RS-485
RS-
-485
485
5 On Output True
PO
ORT3
PORT3 C4
4
+
_
Y5
5 Off Output False
LNK/ACT LED (Green) TX3
TX
X3
Y6
6
RX
X3
RX3
LG
G +V
V
On Connected to the network

Blink Communicating

Off Disconnected from the network

TX & RX LED (Green)
100MBIT LED (Orange) On Com Port Data Active
On Communicating at 100Mbps Off No Communication

Off Communicating at 10Mbps or

disconnected from the network

POWER LED (Green) Ethernet Analog PLC

On Power Good Analog Ethernet PLC
Off Power Failure
C0-12DD1E-D
C0-12D
DD1E--D
D
RUN LED (Green)
C1
1 INPUT LEDs (Green)
On PLC Run Mode X1
X2
2 On Input True
Initializing
Blink System PWR RUN
R UN X3
3
Off
RUN X4
4 Input False
PLC Program ERR STOP
S TOP C2
2
Off Mode
PORT1 Y1 OUTPUT LEDs (Red)
LNK/ACT Y2
2
ETHER Y3
3 On Output True
ERROR LED (RED) NET Y4
4
100MBIT Off Output False
On Self Diagnostic +V
V
Error PORT2
AD
D1
D 1V
AD1V
Self Diagnostic
Blink Warning TX2
AD
D1
D 1I
AD1I
AD
D2
D 2
2V
AD2V V
RX2
AD
D2
D 2
2IV
AD2IVV
RS-232
RS 232
Off No Error AC
CO
C OM
ACOM
RS-485
RS-
-485
485
5 DA
A1
A 1V
DA1V
PO
ORT3
PORT3
+
_
DA
A11
DA11
LNK/ACT LED (Green) TX3
TX
X3
DA
A1V
DA1V
RX
X3
RX3
LG
G DA
A22I
DA2I
On Connected to the network

Blink Communicating

Off Disconnected from the network

TX & RX LED (Green)
100MBIT LED (Orange) On Com Port Data Active
On Communicating at 100Mbps Off No Communication

Off Communicating at 10Mbps or

disconnected from the network

www.automationdirect.com/click-plc CLICK PLCs tCLP-33

 For the latest prices, please check AutomationDirect.com.

CLICK Specifications

I/O Module LED Status Indicators

I/O Module LED Status Indicators
I/O Module LED Status Indicators

POWER LED (Green)

On Power Good
Off Power Failure

OUTPUT LEDs (Red)

On Output True

INPUT LEDs (Green) Off Output False

On Input True
Off Input False
Note: There are no LED indications
on the Analog I/O modules.

Input I/O Module Output I/O Module

I/O Terminal Block Specifications for PLCs and I/O Modules

11-pin Terminal Block Specifications

Connector Type Pluggable Terminal Block
Number of Pins 11
Pitch 3.50 mm
Wire Range 28–16 AWG
Wire Strip Length 7 mm
Screw Size M2.0
Analog, analog combo I/O
Screw Torque modules only: 1.7 lb·in;
All other modules: 2.0 to 2.2 lb·in
ADC Part Number C0-8TB

11-Pin Terminal Block,

C0-8TB

20-pin Terminal Block Specifications

Connector Type Pluggable Terminal Block
Number of Pins 20
Pitch 3.50 mm
Wire Range 28-16 AWG
Wire Strip Length 7 mm
Screw Size M2.0
Analog, analog combo I/O
Screw Torque modules only: 1.7 lb·in;
All other modules: 2.0 to 2.2 lb·in
ADC Part Number C0-16TB

20-Pin Terminal Block,

C0-16TB

tCLP-34 CLICK PLCs 1-800-633-0405

 For the latest prices, please check AutomationDirect.com.

Product Dimensions and Installation

Ground Braid
It is important to understand the Copper Lugs
installation requirements for your CLICK Panel or
system. Your knowledge of these Single Point
Ground
requirements will help ensure that your Panel
system operates within its environmental
and electrical limits.
Star Washers Star Washers
Plan for Safety
This catalog should never be used as a
replacement for the user manual. 2 in.
50.8 mm
You can purchase, download free, or view minimum
online the user manuals for these prod-
ucts. Manual C0-USER-M is the user 2 in.
manual for the CLICK PLC. The user 50.8mm
minimum
manual contains important safety infor-
mation that must be followed. The system 3 in.
76.2 mm
installation should comply with all appro- minimum
priate electrical codes and standards.

NOTE: There is a mimimum clearance requirement of 2 inches(51 mm)

between the CLICK PLC and the panel door or any devices mounted in
the panel door. The same clearance is required between the PLC and any
side of the enclosure. A minimum clearance of 3 inches (76 mm) is required
between the PLC and a wireway or any heat producing device.

Mounting Orientation
CLICK PLCs must be mounted prop-
erly to ensure ample airflow for cooling
purposes. It is important to follow the
unit orientation requirements and to verify
that the PLC’s dimensions are compatible
STOP
RUN

with your application. Notice particularly

PORT1

PORT2
RX1
TX1
RUN

RX2
TX2
PWR

ERR

the grounding requirements and the

recommended cabinet clearances. Air
Flow

www.automationdirect.com/click-plc CLICK PLCs tCLP-11

 For the latest prices, please check AutomationDirect.com.

Product Dimensions and Installation

Latch tabs

Connecting the Modules 3

Together Connecting Modules
CLICK PLCs, I/O modules and power
supplies connect together using the 2
extension ports that are located on the
side panels of the modules (no PLC back-
plane/base required).
1. R emove extension port covers and slide
the latch tabs forward.
2. A lign the module pins and connection
plug, and press the I/O module
onto the right side of the PLC.
1
3. S lide the latch tabs backward to lock
the modules together.

Supports up to eight I/O modules

DIN Rail Mounting Surface Mounting

Mounting Upper
Mounting Tab

The CLICK PLC system, which includes the

CLICK power supplies, PLC units, and I/O
modules, can be mounted in one of two
ways.
1. D IN rail mounted
2. S urface mounted using the built-in
upper and lower mounting tabs.

Pull tab Push tab Click Lower

down. up until... Mounting Tab

Power Supply Unit Dimensions

Module PLC Unit I/O Module mm [inches]
Unit Dimensions
13.5
2.6 34.9 53.5 27
The dimensional drawings here and on [0.102] [1.37] [2.11] [1.06]
[0.46] 75
the next page show the outside dimen- [2.95]
sions of the CLICK power suppy, PLC,
and I/O modules. The CLICK PLC system
is designed to be mounted on standard
35mm DIN rail, or it can be surface
85
5
mounted. [3.35]
.35]
5
Allow proper spacing from other
components within an enclosure.
4
Maximum system: [0.16]

Power Supply + PLC + 8 I/O modules. "

9.4
[0.37]
9.2
[0.36]

tCLP-12 CLICK PLCs 1-800-633-0405

 For the latest prices, please check AutomationDirect.com.

Product Dimensions and Installation

Power Supply
Unit Dimensions
mm [inches]

PLC Units

I/O Modules

www.automationdirect.com/click-plc CLICK PLCs tCLP-13

 For the latest prices, please check AutomationDirect.com.

Networking the CLICK PLC

Built-in Communications
Ports
Basic, Standard and Analog PLCs have
Com Port 1
two built-in RS-232 communications ports. Com Port 1
Standard and Analog PLCs also have one
built-in RS-485 communications port. Com Port 2
One RS-232 port supports the Modbus Com Port 2
RTU protocol only and can be used as the Com Port 3
programming port. The other ports support
Basic PLC Standard and Analog PLCs
either Modbus RTU or ASCII protocol. Both
RS-232 ports supply 5V DC, so you can Com Port 1 Specifications
connect a monochrome C-more Micro HMI Port 1
Use: Programming Port / Serial Communications Port 1 Pin Descriptions
panel without an additional power supply. (Slave only)
6 pin RJ12 Phone 1 0V Power (-) connection (GND)
Physical: 6 pin, RJ12, RS-232
Type Jack 2 5V Power (+) connection
LED Status Indicators Communication speed (baud): 38400 (fixed)
Parity: Odd
3 RXD Receive data (RS-232)
There are LED indicators located to the 4 TXD Transmit data (RS-232)

1
Station Address: 1
left of each communications port to 5 NC No connection
Data length: 8 bits
6 0V Power (-) connection (GND)

6
indicate when the port is transmitting or Stop bit: 1
receiving. Protocol: Modbus RTU (slave only)

Com Port 2 Default Port 2

Basic PLCs Specifications
Use: Serial Communications -
Port 2 Pin Descriptions
Physical: 6 pin, RJ12, RS-232 - 6 pin RJ12 Phone 1 0V Power (-) connection (GND)
Port 1 & 2 LED
Communication speed (baud): 1200, Type Jack 2 5V Power (+) connection
Status Indicators
2400, 4800, 9600, 19200, 38400, 38400 3 RXD Receive data (RS-232)
TX1 and TX2 (Green) STOP 57600, 115200
4 TXD Transmit data (RS-232)

1
On The Comm Port is sending data. PORT1 Parity: odd, even, none Odd 5 RTS Request to send
TX1
Off The Comm Port is not sending data.
Station Address: 1 to 247 1
RX1
6 0V Power (-) connection (GND)
Data length: 8 bits (Modbus RTU) or 6
RX1 and RX2 (Green)
TX2
RX2 7, 8 bits (ASCII) 8 bits
On The Comm Port is receiving data. PORT2
Stop bit: 1,2 1
Off The Comm Port is not receiving data.
Protocol: Modbus RTU Modbus RTU
(master/slave) or ASCII in/out

Standard and Analog PLCs Com Port 3 Default

Specifications
Port 1, 2, & 3 LED Port 3
Status Indicators Use: Serial Communications - Port 3 Pin Descriptions
RUN
Physical: 3 pin, RS-485 - RS-485 Signal A
1 + (plus)
ERR

PORT1
Communication speed (baud): 1200, (RS-485)
TX1, TX2 and TX3 (Green) TX1 2400, 4800, 9600, 19200, 38400, 38400 Signal B
57600, 115200 2 - (minus)
On The Comm Port is sending data. RX1
(RS-485)
Off The Comm Port is not sending data. TX2 Parity: odd, even, none Odd Logic
RX2 3 LG Ground(0 V)
PORT2 Station Address: 1 to 247 1
RX1, RX2 and RX3 (Green)
PORT3
RS-485 Data length: 8 bits (Modbus RTU) or 8 bits
On The Comm Port is receiving data.
TX3
7, 8 bits ( ASCII)
Off The Comm Port is not receiving data. RX3
Stop bit: 1,2 1
Protocol: Modbus RTU Modbus RTU
(master/slave) or ASCII in/out

Port Setup
Use CLICK programming software to
easily configure the communications
ports.

tCLP-14 CLICK PLCs 1-800-633-0405

Networking the CLICK PLC
For the latest prices, please check AutomationDirect.com.

Built-in Communications
Ports
Ethernet Basic, Standard and Analog PLCs
have one built-in Ethernet communications Com Port 1 Com Port 1
port and one RS-232 communications
port. Ethernet Standard and Analog PLCs Com Port 2
also have one built-in RS-485 communica- Com Port 2
tions port. The Ethernet port supports the Com Port 3
Modbus TCP protocol. The RS-232 and
Ethernet Basic PLC Ethernet Standard and
RS-485 ports support either Modbus RTU or Ethernet Analog PLCs
ASCII protocol. The RS-232 port supplies
5 VDC, so you can connect a monochrome Port 1
Com Port 1 Specifications Port 1 Pin Descriptions
C-more Micro HMI panel without an addi- Use: Programming and Ethernet Communication 1 TX+ Transmit Data (+)
tional power supply. 8 pin RJ45
8 pin Phone
RJ45
Physical: 8 pin, RJ45, Ethernet Type Jack 2 TX- Transmit Data (-)
Communication speed (Mbps): 10/100 3 RX+ Receive data (+)
LED Status Indicators Protocol: Modbus TCP 4 NC Not connected

1
There are LED indicators located to 5 NC Not connected
the left of each communication port to 6 RX- Receive Data (-)

8
indicate when the port is transmitting or 7 NC No connection
receiving. 8 NC No connection
Com Port 2 Default Port 2
Ethernet Basic PLCs
Specifications
Use: Serial Communication -
Port 2 Pin Descriptions
Port 11 &
Port & 22 LED
LED
66pin
pin RJ12
RJ12 Phone
Phone 1 0V Power (-) connection (GND)
Physical: 6 pin, RJ12, RS-232 - Type Jack
Type Jack
StatusIndicators
Status Indicators 2 5V Power (+) connection
Communication speed (baud): 2400,
LNK/ACT LED (Green) PWR RU
R
RUN 4800, 9600, 19200, 38400, 57600, 38400 3 RXD Receive data (RS-232)
115200

1
4 TXD Transmit data (RS-232)
RUN
On Connected to the network ERR S
STOP

Blink Communicating
PORT1 Parity: odd, even, none Odd 5 RTS Request to send
LNK/ACT

6
Off Disconnected from the network
ETHER
NET
Station Address: 1 to 247 1 6 0V Power (-) connection (GND)
Data length: 8 bits (Modbus RTU) or
100MBIT

100MBIT LED (Orange) PORT2

7, 8 bits (ASCII) 8 bits
TX2
On Communicating at 100Mbps RX2
RS-232
RS 232
Stop bit: 1,2 1
Off Communicating at 10Mbps or
disconnected from the network Protocol: Modbus RTU Modbus RTU
(master/slave) or ASCII in/out
TX2 (Green)
On The Comm Port is sending data.
Off The Comm Port is not sending data.

RX2 (Green)
Com Port 3 Port 3
Default Port 3 Pin Descriptions
On The Comm Port is receiving data.
Specifications RS-485
RS-485
Off The Comm Port is not receiving data. Signal A
Use: Serial Communication - 1 + (plus)
(RS-485)
Physical: 3 pin, RS-485 - Signal B
Ethernet Standard and 2 - (minus)
Communication speed (baud): 2400, (RS-485)
Ethernet Analog PLCs 4800, 9600, 19200, 38400, 57600, 38400 Logic
Port 1, 2 & 3 LED 115200 3 LG Ground(0 V)
Port 1, Indicators
Status 2, & 3 LED Parity: odd, even, none Odd
Status Indicators
Station Address: 1 to 247 1
LNK/ACT LED (Green)
On Connected to the network
Data length: 8 bits (Modbus RTU) or 8 bits
7, 8 bits ( ASCII)
Blink Communicating
Stop bit: 1,2 1
Off Disconnected from the network
Protocol: Modbus RTU
RUN
ERR
PORT1
STOP
(master/slave) or ASCII in/out Modbus RTU
100MBIT LED (Orange)
LNK/ACT
On Communicating at 100Mbps ETHER
NET
100MBIT
Off Communicating at 10Mbps or
disconnected from the network
PORT2
TX2

TX2 and TX3 (Green)

RX2
RS-232

RS-485
Port Setup
On The Comm Port is sending data. PORT3

Off The Comm Port is not sending data.

TX3
+
_ Use CLICK programming software to
RX3
LG
easily configure the communication
RX2 and RX3 (Green) ports.
On The Comm Port is receiving data.
Off The Comm Port is not receiving data.

www.automationdirect.com/click-plc CLICK PLCs tCLP-15

 For the latest prices, please check AutomationDirect.com.

Networking the CLICK PLC

Typical Communication Applications

The diagrams on these three pages illustrate the typical uses for the CLICK PLC’s communication ports.
Port 1 (RS-232) – Modbus RTU Slave Mode Only

Port 1

C-more and C-more

Micro-Graphic Panel
PC
Another CLICK PLC Other Devices
Supporting Modbus RTU
Master Mode
Basic, Standard
and Analog PLC

C-more Micro-Graphic panels (mono-

chrome models only) can get 5 VDC power
from Com port 1 or 2. C-more 3 Inch
Micro-Graphic
Panel
Example

CLICK PLC
Port 1

The Color Micro-Graphic panel or the second

Monochrome Micro-Graphic panel needs a sepa-
DV-1000CBL rate 24 VDC power source (see the note below).
serial cable
Port 1 or 2

NOTE: CLICK’s (RS-232) Port 1 and Port 2 can provide 5 VDC power to the panel, but not at the same time. If a C-more Micro-Graphic
panel is connected to both ports, then at least one of the panels must be powered by a C-more Micro DC power adapter, EA-MG-P1
or EA-MG-SP1, or another 24 VDC power source. Color C-more Micro-Graphic panels must also be powered from a separate 24 VDC
source.

Do not use the following Direct LOGIC devices with CLICK’s Port 1 or 2:

Warning: The following DirectLOGIC PLC devices cannot be used with a CLICK PLC’s Port 1 or Port 2:
Handheld Programmer for DL05, DL06, DL105, DL205 & D3-350 CPUs, p/n D2-HPP
Handheld Programmer for DL405 CPUs, p/n D4-HPP-1
Timer/Counter Access for DL05, DL06, DL105, DL205, DL405 & D3-350 CPUs, p/n DV-1000

D2-HPP DV-1000
D4-HPP-1

tCLP-16 CLICK PLCs 1-800-633-0405

 For the latest prices, please check AutomationDirect.com.

Networking the CLICK PLC

Port 1 (Ethernet) – Modbus TCP

Modbus TCP Client (Master) Devices

Port 1

Another CLICK
PC
Ethernet PLC

All CLICK
Ethernet PLCs Other Devices
Supporting
Modbus TCP
Client Mode

C-more Panel

Modbus TCP Server (Slave) Devices

Other Devices Supporting

Modbus TCP Server Mode
ViewMarq Display

Another CLICK
Ethernet PLC

SR55 Soft Starter

GS1 Drive GS3 Drive

www.automationdirect.com/click-plc CLICK PLCs tCLP-17

 For the latest prices, please check AutomationDirect.com.

Networking the CLICK PLC

Port 2 (RS-232) – Modbus RTU or ASCII
Port 3 (RS-485; Standard, Analog, Ethernet Standard and Ethernet Analog PLCs) – Modbus RTU or
ASCII
All PLCs have RS-232 port 2, but only Standard, Analog, Ethernet Standard and Ethernet Analog PLCs have RS-485 port 3.
Ports 2 and 3 allow networking to similar devices.

Port 2
Port 2
Port 3

Modbus RTU
Modbus RTU Master Devices

Basic PLC Standard and Analog PLC

Ethernet Basic PLC Ethernet Standard PLC
PC Another CLICK PLC
Ethernet Analog PLC

See Note on previous page about

connecting a C-more Micro-Graphic
panel to Port 1 or 2.

Other Devices
C-more and C-more Supporting Modbus RTU
Micro-Graphic Panel Master Mode

ASCII
Devices that SEND ASCII messages

Other devices
that can send Modbus RTU Slave Devices
ASCII data.
Barcode
Weigh Scale
Reader
Other Devices
Supporting Modbus
RTU Slave Mode

Devices that RECEIVE ASCII messages

Other devices Another CLICK PLC SOLO Temperature

that can receive Controller
ViewMarq ASCII data. (CLICK Port 3 Only)
Display
Serial Printer

tCLP-18 CLICK PLCs 1-800-633-0405

 For the latest prices, please check AutomationDirect.com.

Power Supplies
Power Supplies
The CLICK PLC family offers two 24 VDC CLICK 24 VDC Power Supply Ratings
Part Number Output Current Price C0-00AC
power supplies. They are identical except
for the output current. C0-00AC 0.5 A $29.00
C0-01AC 1.3 A $39.00
It is not mandatory to use one of these
CLICK power supplies for the CLICK PLC C0-00AC Power Supply Specifications
system. You can use any other 24 VDC
Input Voltage Range 85-264 VAC
power supply that Automationdirect.com
Input Frequency 47-63 Hz
offers, including the PSP24-DC12-1 12
Input Current (typical) 0.3 A @ 100 VAC, 0.2 A @ 200 VAC
VDC to 24 VDC converter shown below.
Inrush Current 30 A
C0-00AC Power Supply Output Voltage Range 23-25 VDC
Output Current 0.5 A
Limited auxiliary AC power supply allows Over Current Protection @ 0.65 A (automatic recovery)
you to power the 24 VDC CLICK C0 series Weight 5.3 oz (150g)
PLCs with 100-240 VAC supply power.
The 0.5A DC power supply is capable of
controlling the PLC plus a limited configu- C0-01AC Power Supply Specifications 24 VDC
Input Voltage Range 85-264 VAC Output Power
ration based on the power budget of each Terminals
I/O module. The C0-00AC is a low- Input Frequency 47-63 Hz
(for CLICK PLC, I/O or
cost solution for applications requiring Input Current (typical) 0.9 A @ 100 VAC, 0.6 A @ 200 VAC field device, etc.)
only minimal I/O and power consump- Inrush Current 30 A
85-264 VAC
tion. This power supply will not support a Output Voltage Range 23-25 VDC
Power Source
fully-populated CLICK PLC system with all Output Current 1.3 A
Input Terminals
possible I/O module combinations. Over Current Protection @ 1.6 A (automatic recovery)
Weight 6.0 oz (170g)
C0-01AC Power Supply
Expanded auxiliary AC power supply allows PSP24-DC12-1 DC-DC Converter Specifications
C0-01AC
you to power the 24 VDC CLICK C0 series Input Voltage Range 9.5-18 VDC
PLCs with 100-240 VAC supply power. Input Power (no load) 1.0 W max.
The 1.3A DC power supply is capable Startup Voltage 8.4 VDC
of supporting a fully-populated CLICK Undervoltage Shutdown 7.6 VDC
PLC system with all possible I/O module Output Voltage Range 24-28 VDC (adjustable)
combinations, with no concerns for Output Current 1.0 A
exceeding the power budget. Short Circuit Protection Current limited at 110% typical
Weight 7.5 oz (213g)
PSP24-DC12-1 DC-DC Converter
With this DC-DC converter you can
operate the CLICK PLC with 12 VDC input CLICK Power Supply CLICK PLC
power.

24 VDC
Output Power
Terminals
(for CLICK PLC, I/O or
field device, etc.)

85-264 VAC
Power Source
Input Terminals

24V 24 VDC power is supplied to the PLC

PSP24-DC12-1 0V unit through wiring connected from the
power supply output to the 4-pin 24 VDC
input connector located on the bottom
G of the PLC unit.

www.automationdirect.com/click-plc CLICK PLCs tCLP-19

 For the latest prices, please check AutomationDirect.com.

Power Budgeting
Power Budgeting
There are two areas to be considered when determining the It is strongly recommended that the power source for the logic
power required to operate a CLICK PLC system. The first area side be separate from the power source for the field side to help
is the power required by the CLICK PLC, along with the internal eliminate possible electrical noise.
logic side power that the CPU provides to its own I/O and any Power budgeting requires the calculation of the total current the
connected I/O modules that are powered through the PLC 24 VDC power source needs to provide to CLICK’s logic side,
expansion port; plus any device, such as a C-more Micro-Graphic and also a separate calculation of the total current required for all
panel, that is powered through one of the communications ports. devices operating from the field side of the PLC system.
The second area is the power required by all externally connected Refer to the Power Budgeting example shown on the following
I/O devices. This should be viewed as the field side power page. The table shows required current for a CLICK PLC, two
required. The field side power is dependent on the voltage used I/O modules, and a C-more Micro. Use the total amperage
for a particular input or output device as it relates to the wired values to select the properly sized power supply.
I/O point, and the calculated load rating of the connected device.

CLICK 24 VDC Power Supply Other 24 VDC Power Supply

C0-00AC or C0-01AC Example: PSP24-60S

Power Consumption for

CLICK PLC Units
PLC Current Consumption (mA) PLC Current Consumption (mA)
Power Budget External Power Budget External
Part Number 24 VDC 24 VDC Part Number 24 VDC 24 VDC
(logic side) (field side) (logic side) (field side)
Basic PLC Units Ethernet Analog PLC Units
C0-00DD1-D 120 60 C0-12DD1E-D 60
140
C0-00DD2-D C0-12DD2E-D
C0-00DR-D 120 0 C0-12DRE-D 0
160
C0-00AR-D C0-12ARE-D
Standard PLC Units C0-12DD1E-1-D 60
140
C0-01DD1-D 140 60 C0-12DD2E-1-D
C0-01DD2-D C0-12DRE-1-D 0
160
C0-01DR-D 140 0 C0-12ARE-1-D
C0-01AR-D C0-12DD1E-2-D 60
140
Analog PLC Units C0-12DD2E-2-D
C0-02DD1-D 140 60 C0-12DRE-2-D 160 0
C0-02DD2-D C0-12ARE-2-D 140
140 0
C0-02DR-D
Ethernet Basic PLC Units
C0-10DD1E-D 120 60
C0-10DD2E-D
C0-10DRE-D 120 0
C0-10ARE-D
Ethernet Standard PLC Units
C0-11DD1E-D 140 60
C0-11DD2E-D
C0-11DRE-D 140 0
C0-11ARE-D

tCLP-20 CLICK PLCs 1-800-633-0405

 For the latest prices, please check AutomationDirect.com.

Power Budgeting
Power Consumption for I/O Module Current Consumption
CLICK I/O Expansion Modules (continued) (mA)
Power Budget External
I/O Module Current Consumption (mA) Part Number 24 VDC 24 VDC
(logic side) (field side)
Power Budget External
Part Number 24 VDC 24 VDC Discrete Combo I/O Modules
(logic side) (field side) C0-16CDD1 80 50
Discrete Input Modules C0-16CDD2 80 0
C0-08ND3 30 0 C0-08CDR 80 0
C0-08ND3-1 30 0 Analog Input Modules
C0-16ND3 40 0 C0-04AD-1 20 65
C0-08NE3 30 0 C0-04AD-2 23 65
C0-16NE3 40 0 C0-04RTD 25 0
C0-08NA 30 0 C0-04THM 25 0
Discrete Output Modules Analog Output Modules
C0-08TD1 50 15 C0-04DA-1 20 145
C0-08TD2 50 0 C0-04DA-2 20 85
C0-16TD1 80 100 Analog Combo I/O Modules
C0-16TD2 80 0 C0-4AD2DA-1 25 75
C0-08TA 80 0 C0-4AD2DA-2 20 65
C0-04TRS 100 0 C-more Micro-Graphic Panel
C0-08TR 100 0 Monochrome
90 0
only

Power Budgeting Using the

CLICK Programming Software
The CLICK Programming software can also
be used for power budgeting. Based on the
amperage rating of the power supply selected
in the first column, your power budget is
calculated by subtracting each consecutive
module’s power consumption from the total
available power budget. If you exceed the
maximum allowable power consumption the
power budget row is highlighted in red.

Power Supply PLC Module I/O Module

(C0-01AC) (C0-00DD1-D) (C0-16ND3)
Power Budgeting Example
I/O Module
(C0-16TD1)
Port 1
or
Current Consumption (mA) Example
Port 2 Power Budget External
Part Number 24 VDC 24 VDC
(logic side) (field side)
C0-00DD1-D 120 60
C0-16ND3 40 0
C0-16TD1 80 100
C-more Micro 90 0
Total: 330 160*
* Add in calculated load of connected I/O devices.

C-more
Micro-Graphic
Panel
Only monochrome models
can be powered from port 1 or 2.

www.automationdirect.com/click-plc CLICK PLCs tCLP-21

 For the latest prices, please check AutomationDirect.com.

Wiring System for CLICK PLCs

Wiring Solutions using the ZIPLink Wiring System
ZIPLinks eliminate the normally tedious process of wiring between ZIPLinks are available in a variety of styles to suit your needs,
devices by utilizing prewired cables and DIN rail mount connector including feedthrough connector module. ZIPLinks are avail-
modules. It’s as simple as plugging in a cable connector at either able for all Basic, Standard and Ethernet CLICK PLC units and
end or terminating wires at only one most discrete and analog I/O modules.
end. Prewired cables keep installa- Pre-printed I/O-specific adhesive label
tion clean and efficient, using half the strips for quick marking of ZIPLink
space at a fraction of the cost of stan- modules are provided with ZIPLink cables.
dard terminal blocks.

Solution 1: CLICK PLC and I/O Modules to ZIPLink

Connector Modules
When looking for quick and easy I/O-to-field termination, a ZIPLink Use the “CLICK PLC PLC Unit ZIPLink Selector” table and
connector module used in conjunction with a prewired ZIPLink CLICK I/O ZIPLink selector tables located in this section:
cable, consisting of an I/O terminal block at one end and a multi- 1. Locate your PLC or I/O module.
pin connector at the other end, is the best solution. 2. Select a ZIPLink Module.
3. Select a corresponding ZIPLink Cable.

Solution 2: CLICK PLC and I/O Modules to 3rd

Party Devices
When wanting to connect I/O to another device within close prox- Use the I/O Modules to 3rd Party Devices selector tables
imity of the I/O modules, no extra terminal blocks are necessary located in the ZIPLink section:
when using the ZIPLink Pigtail Cables. ZIPLink Pigtail Cables are 1. Locate your PLC or I/O module.
prewired to an I/O terminal block with color-coded pigtail with 2. S elect a ZIPLink Pigtail Cable that
soldered-tip wires on the other end. is compatible with your 3rd party
device.

Solution 3: GS Series and DuraPulse Drives

Communication Cables
Need to communicate via Modbus RTU to a drive or a network of Use the Drives Communication selector tables located in the
drives? ZIPLink section:
ZIPLink cables are available in a wide range of 1. Locate your Drive and type of communications.
configurations for connecting to PLCs and SureServo, SureStep, 2. Select a ZIPLink cable and other associated hardware.
Stellar Soft Starter and AC drives. Add a ZIPLink communications
module to quickly and easily set up a multi-device network.

Solution 4: Serial Communications Cables

ZIPLink offers communications cables for use with CLICK PLCs that Use the Serial Communications Cables selector table located
can also be used with other communications devices. Connections in the ZIPLink section:
include a 6-pin RJ12 connector which can be used in conjunction 1. Locate your connector type
with the RJ12 Feedthrough module. 2. Select a cable.

www.automationdirect.com/click-plc CLICK PLCs tCLP-35

 For the latest prices, please check AutomationDirect.com.

Wiring System for CLICK PLCs

CLICK PLC ZIPLink Selector CLICK PLC Discrete Input Module ZIPLink Selector
PLC ZIPLink I/O Module ZIPLink
# of Module Cable Input # of Terms Component Module
PLC Unit Part Cable Part
Terms Component Part No. Part No. Module No. No.
C0-00DD1-D C0-08ND3
C0-00DD2-D C0-08ND3-1
11 Feedthrough ZL-RTB20 ZL-C0-CBL11 *
C0-00DR-D C0-08NE3
C0-00AR-D C0-08NA
20 Feedthrough ZL-RTB20 ZL-C0-CBL20 *
C0-01DD1-D Feedthrough ZL-RTB20
C0-16ND3 20
C0-01DD2-D Sensor ZL-LTB16-24
C0-01DR-D ZL-C0-CBL20 *
Feedthrough ZL-RTB20
C0-01AR-D C0-16NE3 20
Sensor ZL-LTB16-24
C0-02DD1-D
C0-02DD2-D No ZIPLinks are available for Analog PLC units.
C0-02DR-D
CLICK PLC Discrete Output Module ZIPLink Selector
C0-10DD1E-D I/O Module ZIPLink
C0-10DD2E-D Output Module Cable
# of Terms Component
C0-10DRE-D Module Part No. Part No.
C0-10ARE-D C0-08TD1
20 Feedthrough ZL-RTB20 ZL-C0-CBL20 *
C0-11DD1E-D C0-08TD2
C0-11DD2E-D 11 Feedthrough ZL-RTB20 ZL-C0-CBL11 *
C0-08TR
C0-11DRE-D C0-08TA
C0-11ARE-D Feedthrough ZL-RTB20
C0-12DD1E-D C0-16TD1 20 Fuse ZL-RFU20 2 ZL-C0-CBL20*
C0-12DD2E-D Relay (sinking) ZL-RRL16-24-1
C0-12DRE-D Feedthrough ZL-RTB20
C0-12ARE-D C0-16TD2 20 Fuse ZL-RFU20 2 ZL-C0-CBL20 *
C0-12DD1E-1-D Relay (sourcing) ZL-RRL16-24-2
C0-12DD2E-1-D C0-04TRS1 20 Feedthrough ZL-RTB20 ZL-C0-CBL20 *
No ZIPLinks are available for Ethernet Analog PLC units.
C0-12DRE-1-D
C0-12ARE-1-D
C0-12DD1E-2-D CLICK PLC Combo I/O Module ZIPLink Selector
C0-12DD2E-2-D I/O Module ZIPLink
C0-12DRE-2-D
Combo Module Cable
C0-12ARE-2-D # of Terms Component
Module Part No. Part No.
1 Note: The C0-04TRS relay output is derated not to exceed 2A per point maximum C0-16CDD1
20 Feedthrough ZL-RTB20 ZL-C0-CBL20 *
when used with the ZIPLink wiring system. C0-16CDD2
2 Note: Fuses (5 x 20 mm) are not included. See Edison Electronic Fuse section C0-08CDR 11 Feedthrough ZL-RTB20 ZL-C0-CBL11 *
for (5 x 20 mm) fuse. S500 and GMA electronic circuit protection for fast-acting
maximum protection. S506 and GMC electronic circuit protection for time-delay
performance. Ideal for inductive circuits. CLICK PLC Analog I/O Module ZIPLink Selector
To ensure proper operation, do not exceed the voltage and current rating of
ZIPLink module. ZL-RFU20 = 2A per circuit. I/O Module ZIPLink
Analog # of Module Cable
Component
Module Terms Part No. Part No.
C0-04AD-1 11 Feedthrough ZL-RTB20 ZL-C0-CBL11 *
C0-04AD-2 11 Feedthrough ZL-RTB20 ZL-C0-CBL11 *
C0-04RTD 20 No ZIPLinks are available for RTD and thermocouple
C0-04THM 11 modules.
C0-04DA-1 11 Feedthrough ZL-RTB20 ZL-C0-CBL11 *
C0-04DA-2 11 Feedthrough ZL-RTB20 ZL-C0-CBL11 *
C0-4AD2DA-1 20 Feedthrough ZL-RTB20 ZL-C0-CBL20 *
C0-4AD2DA-2 20 Feedthrough ZL-RTB20 ZL-C0-CBL20 *
* Select the cable length by replacing the * with: Blank = 0.5m, -1 = 1.0m,
or -2 = 2.0m.

tCLP-36 CLICK PLCs 1-800-633-0405