SLC Signaling Line Circuit

Intelligent Control Panel
SLC
Wiring Manual
G
Document 51253
11/29/2005 Rev:
P/N 51253:G ECN 05-473
Fire Alarm System Limitations
While a fire alarm system may lower insurance rates, it is not a substitute for fire insurance!
An automatic fire alarm system—typically made up of Heat detectors do not sense particles of combustion and
smoke detectors, heat detectors, manual pull stations, audible alarm only when heat on their sensors increases at a predeter-
warning devices, and a fire alarm control panel with remote mined rate or reaches a predetermined level. Rate-of-rise
notification capability—can provide early warning of a develop- heat detectors may be subject to reduced sensitivity over time.
ing fire. Such a system, however, does not assure protection For this reason, the rate-of-rise feature of each detector
against property damage or loss of life resulting from a fire. should be tested at least once per year by a qualified fire pro-
The Manufacturer recommends that smoke and/or heat detec- tection specialist. Heat detectors are designed to protect
tors be located throughout a protected premise following the property, not life.
recommendations of the current edition of the National Fire IMPORTANT! Smoke detectors must be installed in the
Protection Association Standard 72 (NFPA 72), manufacturer's same room as the control panel and in rooms used by the sys-
recommendations, State and local codes, and the recommen- tem for the connection of alarm transmission wiring, communi-
dations contained in the Guide for Proper Use of System cations, signaling, and/or power. If detectors are not so
Smoke Detectors, which is made available at no charge to all located, a developing fire may damage the alarm system, crip-
installing dealers. A study by the Federal Emergency Man- pling its ability to report a fire.
agement Agency (an agency of the United States government) Audible warning devices such as bells may not alert people
indicated that smoke detectors may not go off in as many as if these devices are located on the other side of closed or
35% of all fires. While fire alarm systems are designed to pro- partly open doors or are located on another floor of a building.
vide early warning against fire, they do not guarantee warning Any warning device may fail to alert people with a disability or
or protection against fire. A fire alarm system may not provide those who have recently consumed drugs, alcohol or medica-
timely or adequate warning, or simply may not function, for a tion. Please note that:
variety of reasons:
• Strobes can, under certain circumstances, cause seizures
Smoke detectors may not sense fire where smoke cannot in people with conditions such as epilepsy.
reach the detectors such as in chimneys, in or behind walls, on
roofs, or on the other side of closed doors. Smoke detectors • Studies have shown that certain people, even when they
also may not sense a fire on another level or floor of a building. hear a fire alarm signal, do not respond or comprehend the
A second-floor detector, for example, may not sense a first- meaning of the signal. It is the property owner's responsi-
floor or basement fire. bility to conduct fire drills and other training exercise to
make people aware of fire alarm signals and instruct them
Particles of combustion or “smoke” from a developing fire on the proper reaction to alarm signals.
may not reach the sensing chambers of smoke detectors
because: • In rare instances, the sounding of a warning device can
cause temporary or permanent hearing loss.
• Barriers such as closed or partially closed doors, walls, or
chimneys may inhibit particle or smoke flow. A fire alarm system will not operate without any electrical
power. If AC power fails, the system will operate from standby
• Smoke particles may become “cold,” stratify, and not reach batteries only for a specified time and only if the batteries have
the ceiling or upper walls where detectors are located. been properly maintained and replaced regularly.
• Smoke particles may be blown away from detectors by air Equipment used in the system may not be technically com-
outlets. patible with the control panel. It is essential to use only equip-
• Smoke particles may be drawn into air returns before ment listed for service with your control panel.
reaching the detector. Telephone lines needed to transmit alarm signals from a
The amount of “smoke” present may be insufficient to alarm premise to a central monitoring station may be out of service
smoke detectors. Smoke detectors are designed to alarm at or temporarily disabled. For added protection against tele-
various levels of smoke density. If such density levels are not phone line failure, backup radio transmission systems are rec-
created by a developing fire at the location of detectors, the ommended.
detectors will not go into alarm. The most common cause of fire alarm malfunction is inade-
Smoke detectors, even when working properly, have sensing quate maintenance. To keep the entire fire alarm system in
limitations. Detectors that have photoelectronic sensing excellent working order, ongoing maintenance is required per
chambers tend to detect smoldering fires better than flaming the manufacturer's recommendations, and UL and NFPA stan-
fires, which have little visible smoke. Detectors that have ion- dards. At a minimum, the requirements of NFPA 72 shall be
izing-type sensing chambers tend to detect fast-flaming fires followed. Environments with large amounts of dust, dirt or
better than smoldering fires. Because fires develop in different high air velocity require more frequent maintenance. A main-
ways and are often unpredictable in their growth, neither type tenance agreement should be arranged through the local man-
of detector is necessarily best and a given type of detector ufacturer's representative. Maintenance should be scheduled
may not provide adequate warning of a fire. monthly or as required by National and/or local fire codes and
Smoke detectors cannot be expected to provide adequate should be performed by authorized professional fire alarm
warning of fires caused by arson, children playing with installers only. Adequate written records of all inspections
matches (especially in bedrooms), smoking in bed, and violent should be kept.
explosions (caused by escaping gas, improper storage of
flammable materials, etc.). Limit-C-9-2005
2 The SLC Wiring Manual — P/N 51253:G 11/29/2005

Installation Precautions
Adherence to the following will aid in problem-free installation with long-term reliability:
WARNING - Several different sources of power can be Like all solid state electronic devices, this system may
connected to the fire alarm control panel. Disconnect all operate erratically or can be damaged when subjected to light-
sources of power before servicing. Control unit and associ- ning induced transients. Although no system is completely
ated equipment may be damaged by removing and/or insert- immune from lightning transients and interference, proper
ing cards, modules, or interconnecting cables while the unit is grounding will reduce susceptibility. Overhead or outside aerial
energized. Do not attempt to install, service, or operate this wiring is not recommended, due to an increased susceptibility
unit until manuals are read and understood. to nearby lightning strikes. Consult with the Technical Ser-
CAUTION - System Re-acceptance Test after Software vices Department if any problems are anticipated or encoun-
Changes: To ensure proper system operation, this product tered.
must be tested in accordance with NFPA 72 after any pro- Disconnect AC power and batteries prior to removing or
gramming operation or change in site-specific software. Re- inserting circuit boards. Failure to do so can damage circuits.
acceptance testing is required after any change, addition or Remove all electronic assemblies prior to any drilling, filing,
deletion of system components, or after any modification, reaming, or punching of the enclosure. When possible, make
repair or adjustment to system hardware or wiring. All compo- all cable entries from the sides or rear. Before making modifi-
nents, circuits, system operations, or software functions known cations, verify that they will not interfere with battery, trans-
to be affected by a change must be 100% tested. In addition, former, or printed circuit board location.
to ensure that other operations are not inadvertently affected,
at least 10% of initiating devices that are not directly affected Do not tighten screw terminals more than 9 in-lbs. Over-
by the change, up to a maximum of 50 devices, must also be tightening may damage threads, resulting in reduced terminal
tested and proper system operation verified. contact pressure and difficulty with screw terminal removal.
This system meets NFPA requirements for operation at 0-49º This system contains static-sensitive components.
C/32-120º F and at a relative humidity 93% ± 2% RH (non- Always ground yourself with a proper wrist strap before han-
condensing) at 32°C ± 2°C (90°F ± 3°F). However, the useful dling any circuits so that static charges are removed from the
life of the system's standby batteries and the electronic com- body. Use static suppressive packaging to protect electronic
ponents may be adversely affected by extreme temperature assemblies removed from the unit.
ranges and humidity. Therefore, it is recommended that this Follow the instructions in the installation, operating, and pro-
system and its peripherals be installed in an environment with gramming manuals. These instructions must be followed to
a normal room temperature of 15-27º C/60-80º F. avoid damage to the control panel and associated equipment.
Verify that wire sizes are adequate for all initiating and indi- FACP operation and reliability depend upon proper installation.
cating device loops. Most devices cannot tolerate more than a Precau-D1-9-2005
10% I.R. drop from the specified device voltage.
FCC Warning
WARNING: This equipment generates, uses, and can Canadian Requirements
radiate radio frequency energy and if not installed and This digital apparatus does not exceed the Class A limits
used in accordance with the instruction manual may for radiation noise emissions from digital apparatus set
cause interference to radio communications. It has been out in the Radio Interference Regulations of the Cana-
tested and found to comply with the limits for class A dian Department of Communications.
computing devices pursuant to Subpart B of Part 15 of
FCC Rules, which is designed to provide reasonable Le present appareil numerique n'emet pas de bruits radi-
protection against such interference when devices are oelectriques depassant les limites applicables aux appa-
operated in a commercial environment. Operation of this reils numeriques de la classe A prescrites dans le
equipment in a residential area is likely to cause interfer- Reglement sur le brouillage radioelectrique edicte par le
ence, in which case the user will be required to correct ministere des Communications du Canada.
the interference at his or her own expense.
Acclimate Plus™, HARSH™, NIS™, Notifier Integrated Systems™, NOTI•FIRE•NET™, and ONYXWorks™ are all trademarks; and FlashScan®, NION®,
NOTIFIER®, ONYX®, UniNet®, VeriFire®, and VIEW® are all registered trademarks of Honeywell International Inc. Echelon® is a registered trademark and
LonWorks™ is a trademark of Echelon Corporation. ARCNET® is a registered trademark of Datapoint Corporation. Microsoft® and Windows® are
registered trademarks of the Microsoft Corporation. LEXAN® is a registered trademark of GE Plastics, a subsidiary of General Electric Company.
©2005 by Honeywell International Inc. All rights reserved. Unauthorized use of this document is strictly prohibited.
The SLC Wiring Manual — P/N 51253:G 11/29/2005 3

Documentation Feedback
Your feedback helps us keep our documentation up-to-date and accurate. If you have any com-
ments or suggestions about our online Help or printed manuals, you can email us.
Please include the following information:

• Product name and version number (if applicable)
• Printed manual or online Help
• Topic Title (for online Help)
• Page number (for printed manual)
• Brief description of content you think should be improved or corrected
• Your suggestion for how to correct/improve documentation
Send email messages to:

FireSystems.TechPubs@honeywell.com
Please note this email address is for documentation feedback only. If you have any technical
issues, please contact Technical Services.

Table of Contents
Section 1: Introduction ............................................................................................................ 9
1.1: About This Manual ........................................................................................................................................9
1.2: UL 864 Compliance.......................................................................................................................................9
1.2.1: Products Subject to AHJ Approval......................................................................................................9
1.3: Reference Documentation .........................................................................................................................10
1.4: SLC Overview .............................................................................................................................................11
1.5: Polling Protocols .........................................................................................................................................11
1.6: Devices ........................................................................................................................................................12
1.6.1: Monitor/Zone Interface Modules.......................................................................................................12
1.6.2: Control Modules ................................................................................................................................12
1.6.3: Isolator Modules ................................................................................................................................13
1.6.4: Relay Modules...................................................................................................................................13
1.6.5: Transponders .....................................................................................................................................13
1.6.6: Plug-in Detector Bases ......................................................................................................................13
1.6.7: Intelligent Detectors ..........................................................................................................................13
1.6.8: Addressable Manual Pull Stations.....................................................................................................14
1.6.9: RFX Wireless Interface .....................................................................................................................14
1.6.10: ACPS-2406 Addressable Charger/Power Supply............................................................................14
1.6.11: AMPS-24/E Addressable Power Supply .........................................................................................15
1.7: SLC Capacity...............................................................................................................................................15
1.8: SLC Performance.........................................................................................................................................15
1.9: LED Operation.............................................................................................................................................16
Section 2: Wiring Requirements............................................................................................ 17
2.1: Recommended SLC Wiring.........................................................................................................................17
2.2: Two-Wire SLC - Style 4 (Class B) ..............................................................................................................19
2.2.1: Measuring Loop Resistance...............................................................................................................19
2.2.2: Measuring Total Wire Length ...........................................................................................................19
2.3: Four-Wire SLC Style 6 & 7 (Class A).........................................................................................................20
2.3.1: Measuring Loop Resistance...............................................................................................................20
2.3.2: Measuring Total Wire Length ...........................................................................................................20
2.4: Control Panel Terminal Blocks....................................................................................................................21
2.4.1: NFS2-3030 and NFS-3030 with LCM-320, LEM-320 ....................................................................21
2.4.2: NFS-640 with LEM-320....................................................................................................................21
2.4.3: AFP-100 ............................................................................................................................................21
2.4.4: AFP-200 ............................................................................................................................................21
2.4.5: AFP-300/AFP-400.............................................................................................................................22
2.4.6: AM2020/AFP1010 with LIB-200A or LIB-400 ...............................................................................22
2.4.7: System 5000 with AIM-200 ..............................................................................................................23
Section 3: Shielded Wire Termination .................................................................................. 25
3.1: Overview......................................................................................................................................................25
3.2: No Conduit...................................................................................................................................................25
3.3: Full Conduit .................................................................................................................................................26
3.4: Partial Conduit .............................................................................................................................................26
3.5: Floating Shield ............................................................................................................................................27
Section 4: SLC Circuits without Isolators ............................................................................ 29
4.1: Overview......................................................................................................................................................29
4.2: NFPA Style 4 SLC .......................................................................................................................................29
4.3: NFPA Style 6 SLC .......................................................................................................................................30
Section 5: SLC Circuits with Isolators .................................................................................. 31
5.1: Overview......................................................................................................................................................31
5.2: Fault Isolator Module ..................................................................................................................................31

Table of Contents
5.2.1: Wiring an Isolator Module.................................................................................................................32

5.3: Isolator Detector Bases ................................................................................................................................32
5.3.1: How an Isolator Base Works .............................................................................................................33
5.4: NFPA Style 4 SLC Using Isolator Modules ................................................................................................34
5.5: NFPA Style 6 SLC Using Isolator Modules ................................................................................................35
5.6: NFPA Style 7 SLC Using an Isolating Device.............................................................................................36
Section 6: Monitor Modules................................................................................................... 37
6.1: Description ...................................................................................................................................................37
6.1.1: Addressable Monitor Module ............................................................................................................37
6.1.2: Zone Interface Module ......................................................................................................................37
6.1.3: Dual Monitor Module ........................................................................................................................38
6.1.4: Miniature Monitor Module ................................................................................................................38
6.2: Setting an SLC Address for a Module .........................................................................................................39
6.3: NFPA Style B IDC Using Monitor Modules ...............................................................................................39
6.4: NFPA Style D IDC Using Monitor Modules ...............................................................................................41
6.5: NFPA Style B IDC Using Dual Monitor Modules.......................................................................................42
6.6: NFPA Style B IDC Using Zone Interface Modules .....................................................................................43
6.7: NFPA Style D IDC Using Zone Interface Modules.....................................................................................44
Section 7: Control Modules ................................................................................................... 45
7.1: Description ...................................................................................................................................................45
7.2: Wiring a NAC with Addressable Control Modules .....................................................................................45
7.3: Wiring a Style Y NAC (Two-Wire) with Addressable Control Modules ....................................................47
7.4: Wiring a Style Z NAC (Four-Wire) with Addressable Control Modules ....................................................48
7.5: Connecting a Releasing Device to the Addressable Control Module..........................................................49
Section 8: Relay Module ........................................................................................................ 51
8.1: Description ...................................................................................................................................................51
8.2: Wiring the Addressable Relay Module (Form-C Relay) .............................................................................51
Section 9: Intelligent Detector Bases ................................................................................... 53
9.1: Description ...................................................................................................................................................53
9.2: Wiring a Detector Base ................................................................................................................................53
9.3: Wiring an Isolator Base................................................................................................................................55
9.4: Wiring a Relay Base.....................................................................................................................................55
9.5: Wiring a Sounder Base.................................................................................................................................56
Section 10: Addressable Manual Pull Station...................................................................... 57
10.1: Description .................................................................................................................................................57
10.2: Wiring a Manual Pull Station.....................................................................................................................57
Appendix A: Power Considerations...................................................................................... 59
A.1: Supplying Power to 24 VDC Detectors and NACs ....................................................................................59
A.2: Supervising 24 VDC Power ........................................................................................................................60
A.2.1: Using Type Codes with Built-In Power Supervision on NFS2-3030 and NFS-3030 ......................60
A.2.2: Power Supervision Relay..................................................................................................................60
A.2.3: Using the Addressable Control Module Without Relay ...................................................................62
Style Y NAC Power Wiring .................................................................................................................62
Style Z NAC Power Wiring (Alternate) ...............................................................................................63
Appendix B: SLC Surge Suppression .................................................................................. 65
B.1: Introduction .................................................................................................................................................65
B.2: Installation ...................................................................................................................................................66
B.2.1: AFP-100 & AFP-200 ........................................................................................................................66
DTK-2LVLP-F Connections ...............................................................................................................66
PLP-42N Connections ........................................................................................................................66
SLCP-30 Connections .........................................................................................................................67
B.2.2: AFP-300, AFP-400 ..........................................................................................................................67

Table of Contents
DTK-2LVLP-F Connections ...............................................................................................................67

SLCP-30 Connections .........................................................................................................................68
B.2.3: AM2020 & AFP1010 (LIB-200A or LIB-400) ................................................................................68
DTK-2LVLP-F Connections ..............................................................................................................68
SLCP-30 Connections ........................................................................................................................69
B.2.4: NFS-640/E, NFS-3030/NFS2-3030 .................................................................................................69
DTK-2LVLP-F Connections ..............................................................................................................69
SLCP-30 Connections ........................................................................................................................69
Index......................................................................................................................................... 71

Table of Contents

Section 1: Introduction
1.1 About This Manual

This document covers the installation and wiring of various Signaling Line Circuit (SLC) devices,
when used with the following Fire Alarm Control Panels1 (FACPs):
• AFP-100 • NFS-3030/NFS2-3030
• AFP-200 • NFS-640/E
• AFP-300/AFP-400 • System 5000 with AIM-200
• AM2020/AFP1010
This document also provides basic information that applies to Notifier SLC loops in general, such
as the branch resistance measurements.
See Section 2.4, “Control Panel Terminal Blocks”, on page 21 for basic panel-end SLC
connections. Additional information about each control panel and the modules and detectors
referenced in this document, and the part numbers for their manuals, can be found in the respective
installation manual as listed in Table 1.3 below.
NOTE: FireWarden-100 SLC devices are not compatible with the Notifier panels in this manual;
refer to the FireWarden-100 SLC Manual P/N 52304.
1.2 UL 864 Compliance

1.2.1 Products Subject to AHJ Approval
This SLC Wiring Manual accompanies installation, operation, and programming manuals for various fire alarm
control panels (FACPs). NFS2-3030 has been certified to comply with the requirements in the Standard for Control
Units and Accessories for Fire Alarm Systems, UL 864 9th Edition.
The following products have not received UL 864 9th Edition certification and may only be used in retrofit
applications. Operation of the SLC with products not tested for UL 864 9th Edition has not been evaluated and may
not comply with NFPA 72 and/or the latest edition of UL 864. These applications will require the approval of the
local Authority Having Jurisdiction (AHJ).
• AFP-100 • NFS-3030 with CPU-3030
• AFP-200 • NFS-640/E
• AFP-300/AFP-400 • System 5000
• AIM-200 • XP Series (XPP-1, XPC-8, XPM-8 &
• AM2020/AFP1010 XPR-8)
• BGX-101L • XP5-C
• CMX-1 • XP5-M
• CMX-2 • ACPS-2406
• FFT-7/FFT-7S • B224RB
• LIB-400 • B501BH
• MMX-1 • B501BHT
• MMX-101 • FCPS-24/E
• MMX-2
• MPS-24A/E
• MPS-24B/E
• MPS-400
• NCA
1. AFC-600 has been discontinued; to service existing installations of this panel, refer to the
original manuals shipped with the panel.

Introduction Reference Documentation
1.3 Reference Documentation

The table below provides a list of documents referenced in this manual, as well as documents for
selected other compatible devices. The document series chart (DOC-NOT) provides the current
document revision. A copy of this document is included in every shipment.
Compatible Conventional Devices (Non-addressable) Document Number
Device Compatibility Document 15378
Fire Alarm Control Panel (FACP) and Main Power Supply Installation Document Number
AFP-100 Instruction Manual 51010
AFP-200 Instruction Manual 15511
AFP-300/AFP-400 Installation, Operations, and Programming Manuals 50253, 50259, 50260
FireWarden-100 Installation Manual 52299
FireWarden-100 SLC Manual 52304
NFS-640 Installation, Operations, and Programming Manuals 51332, 51334, 51333
NFS2-3030 FACP Installation, Operations, and Programming Manuals 52544, 52546, 52545
NFS-3030 FACP Installation, Operations, and Programming Manuals 51330, 51345, 51344
Voice Alarm System Manual 51252
FireVoice-25/50 & FireVoice-25/50ZS Manual 52290
DVC Digital Voice Command Manual 52411
DAA Digital Audio Amplifier Manual 52410
AA-series Audio Amplifier Manual 52526
AM2020/AFP1010 Installation Manual 15088
System 5000 Installation, Operations, and Programming Manuals 15583, 15581, 15584
System 5000 with AIM-200: Refer to the AIM-200 Manual 15949
Power Supplies, Auxiliary Power Supplies & Battery Chargers Document Number
ACPS-2406 Installation Manual 51304
AMPS-24/E Power Supply Manual 51907
FCPS-24 Field Charger/Power Supply Manual 50059
FCPS-24S6/FCPS-24S8 Field Charger/Power Supply 51977
System Components Document Number
RA400Z Remote LED Annunciator Installation Document I56-508
RFX Wireless Interface Manual 51012
XP Transponder Manual 15888
XP10-M Installation Document I56-1803
XP5 Series Manual 50786
XP6-C Installation Document I56-1805
XP6-MA Installation Document I56-1806
XP6-R Installation Document I56-1804
XPIQ Audio Transponder Manual 51013
SLC Loop Devices Document Number
B224BI Isolator Base Installation Document I56-725
B224RB Relay Base Installation Document I56-659
B501 Standard Base Installation Document I56-357
B501BH Sounder Base Installation Document I56-0491
B501BHT Temporal Sounder Base Installation Document I56-1367
B710HD HARSH™ Base Installation Document I56-1252
B710LP Flanged Base Installation Document I56-637
FAPT-751 Acclimate Plus™ Multi-Sensor Detector Installation Document I56-0002
FAPT-851: See document for FSP-851, FSP-851T and FAPT-851
FCM-1 Control Module Installation Document I56-1169
FDM-1 Dual Monitor Module Installation Document I56-1463
Table 1.1 Reference Documentation (1 of 2)

SLC Overview Introduction
FMM-1 Monitor Module Installation Document I56-1171

FMM-101 Mini Monitor Module Installation Document I56-1173
FRM-1 Relay Module Installation Document I56-1170
FSB-200, FSB-200S Single-ended Reflected Type Projected Beam Smoke Detector I56-2424
FSD-751PL Low-flow Duct Detector I56-1978
FSD-751RPL Low-flow Duct Detector with Relay I56-1979
FSD-751P Duct Detector Installation Document I56-1523
FSD-751RP Duct Detector Installation Document I56-1571
FSH-751 HARSH™ Installation Document I56-054
FSI-751 Ion Detector Installation Document I56-1249
FSI-851 Ion Detector Installation Document I56-1924
FSL-751 Laser Detector Installation Document I56-057
FSP-751 & FSP-751T Photo Installation Document I56-1230
FSP-851, FSP-851T and FAPT-851 Photoelectric Detectors Installation Document I56-1925
FST-751 Thermal Detector Installation Document I56-1234
FST-751R Rate of Rise Sensor Installation Document I56-1242
FST-851, FST-851R, and FST-851H Thermal Detectors Installation Document I56-1926
FZM-1 Zone Interface Module Installation Document I56-1172
HPX-751 HARSH™ Installation Document I56-1250
ISO-X Isolator Module Installation Document I56-1380
LPX-751 Laser Detector Installation Document I56-748
LPX-751L Laser Detector Installation Document I56-1793
NBG-12LX Pull Station Installation Document 51093
Note: Refer to the Device Compatibility Document for compatible conventional devices.
Table 1.1 Reference Documentation (2 of 2)
1.4 SLC Overview

Communication between the control panel and intelligent addressable monitor and control devices
takes place through a Signaling Line Circuit (SLC), which can be wired to meet the requirements of
NFPA Style 4, Style 6, or Style 7.
At least one secondary surge protector must be used with each SLC wiring pair whenever SLC
wiring runs outside the building. For detailed information refer to Appendix B, “SLC Surge
Suppression”, on page 65.
1.5 Polling Protocols

FlashScan® is a patented system (US Patent Number 5,539,389) that greatly enhances the speed of
communication between analog intelligent devices. Communication is in a grouped fashion. If one
of the devices within the group has new information, the panel CPU stops the group poll and
concentrates on single points. Not all panels are Flashscan® capable; see below.
CLIP (Classic Loop Interface Protocol) polls devices in sequential order. The number of devices
connected is limited to 99 detectors and 99 modules per loop. SLC devices are limited to addresses
1-99 only. Many but not all FlashScan-capable devices can be set to run in CLIP mode; see
installation sheet shipped with the device.
Protocol Use: NFS2-3030, NFS-3030, and NFS-640/E can run in FlashScan mode or CLIP mode.
AFP-100, AFP1010, AFP-200, AFP-300/AFP-400, AM2020, and System 5000 with AIM-200 run
in CLIP mode only.
Many FlashScan devices can be programmed to run in either CLIP or FlashScan mode. Use one of
the following three options with SLC loops:
1. Program all modules and detectors on an SLC as FlashScan.

Introduction Devices
2. Program all modules and detectors on an SLC as CLIP.
CAUTION:
! Do not program more than 99 addresses on a CLIP-mode SLC loop, because this will slow the
system down and compromise the response time of the panel to display off-normal events.
3. Program all detectors as CLIP and all modules as FlashScan on an SLC.
CAUTION:
! Do not program modules as CLIP and detectors as FlashScan on the same SLC. This combination
does not work.
1.6 Devices
1.6.1 Monitor/Zone Interface Modules
These addressable modules allow the control panel to monitor entire circuits of conventional alarm
initiating devices, such as manual pull stations, smoke detectors, heat detectors, waterflow and
supervisory devices.
• FMM-1 Monitor Module; FlashScan or CLIP mode. (An earlier module named MMX-1 was
CLIP mode only.)
• FDM-1 Dual Monitor Module; FlashScan or CLIP mode.
• FMM-101 Addressable Mini-Monitor Module; FlashScan or CLIP mode. (An earlier module
named MMX-101 was CLIP mode only.)
• FZM-1 Zone Interface Module; FlashScan or CLIP mode. (An earlier module named MMX-2
was CLIP mode only).
• XP5-M - Supervises five Class-B addressable Initiating Device Circuits (IDC) which monitor
normally open contact initiating devices. Supports FlashScan or CLIP mode. This module is
capable of participating in degraded mode where supported by the FACP. (See the XP5 Series
Manual)
• XP6-MA Allows an intelligent alarm system to monitor six zones of conventional two-wire
detectors; FlashScan or CLIP mode.
• XP10-M Supervises ten Class-B addressable Initiating Device Circuits (IDC) which monitor
normally open contact initiating devices; FlashScan or CLIP mode. This module is capable of
participating in degraded mode where supported by the FACP.
1.6.2 Control Modules

Through these addressable modules, the control panel can selectively activate Notification
Appliance Circuits (NAC).
• FCM-1 Control Module; FlashScan or CLIP mode. (Earlier monitor modules named CMX-1
and CMX-2 were CLIP mode only.)
• XP5-C Acts as a NAC or a speaker/telephone circuit (Class B only) or a Form-C relay.
FlashScan capable. (See the XP5 Series Manual)
• XP6-C Controls six NAC or speaker/telephone circuits; FlashScan or CLIP mode.
• FTM-1 Firefighter’s Telephone Module; FlashScan-only device for use with Fire Fighters
Telephone on NFS-640, NFS-3030, and NFS2-3030. (See the Voice Alarm System Manual, the
DVC Manual, or the DAA Manual.)

Devices Introduction
1.6.3 Isolator Modules

Isolator Modules permit a short-circuited section of the SLC to be fault isolated from the remainder
of the SLC loop, allowing critical components to function in the event of a circuit fault. Isolator
modules are required to meet the requirements of an NFPA Style 7 circuit.
• ISO-X Loop Fault Isolator Module; FlashScan or CLIP mode.
1.6.4 Relay Modules

This addressable module provides the control panel with a dry-contact output for activating a
variety of auxiliary devices.
• FRM-1 Relay Module; FlashScan or CLIP mode.
• XP6-R Controls six Form-C relays; FlashScan or CLIP mode.
1.6.5 Transponders
• XPIQ An integrated, multiple channel audio amplification and distribution subsystem
remotely controlled by the FACP. It can direct up to four low level audio signals from risers to
up to four audio amplifiers, which are then directed to up to four integrated, continuously
supervised speaker circuits. The XPIQ is FlashScan capable (only).
• XP Series (XPP-1, XPC-8, XPM-8 & XPR-8) Provides the FACP with an efficient multiplex
subsystem capability. It communicates with the FACP and functions as a data-gathering panel
for alarm Initiating Device Circuits and as a remote switching center for Notification
Appliance Circuits (NAC), telephone circuits or relays. Not FlashScan capable.
For information on connecting these transponders to the SLC, refer to the XP Transponder Manual
or the XPIQ Manual.
1.6.6 Plug-in Detector Bases

Plug-in detector bases provide a connection between the SLC and a variety of intelligent detectors
which are snapped into place. Standard and isolator bases are used depending upon which NFPA
SLC style is required. Sounder and relay bases are similar to standard bases, but have sound or
relay capabilities.
• Standard Base - Models B501 (standard small diameter base, commonly used in European
installations) and B710LP (standard large diameter base, commonly used in US installations)
• HARSH™ Base - Model B710HD
• Isolator Base - Model B224BI isolator base.
• Sounder Base - Models B501BH (standard sounder base) and B501BHT (base with temporal
sounder)
• Relay Base - Model B224RB relay base
1.6.7 Intelligent Detectors

FSB-200S Addressable, intelligent, single-ended beam smoke detector with built-in sensitivity
testing. The FSB-200 is the same except that it does not provide sensitivity testing. Both models
support FlashScan and CLIP mode.
FAPT-851 (Acclimate Plus™) Addressable, intelligent detector that combines a photoelectric
sensing chamber and fixed temperature heat detection (135°F / 57.2°C). FlashScan capable. (An
earlier version named FAPT-751 was also FlashScan capable. The model named IPX-751 was
discontinued as of December 1, 2001.)

Introduction Devices
FSI-851 Addressable, intelligent smoke detector that incorporates an ionization sensing chamber.
Designed to provide open area protection. FlashScan capable. (An earlier model named FSI-751
was also FlashScan capable. Earlier models named CPX-751 and CPX-551 were CLIP mode
only.)
FSP-851 Analog, addressable intelligent smoke detector that uses a photoelectric sensing chamber.
Listed for use in ducts. Designed to provide open area protection. The FSP-851T adds thermal
sensors that will alarm at a fixed temperature of 135° F (57.2°C). Both models support FlashScan
or CLIP mode. (Earlier versions named FSP-751 and FSP-751T also supported FlashScan or CLIP
mode, but were not listed for use in ducts. Earlier models named SDX-551, SDX-751 and
SDX-551TH were CLIP mode only.)
FST-851 Intelligent thermistor sensing circuit for fast response. Designed to provide open area
protection with 50 foot spacing capability. A fixed temperature sensor with 135°F (57.2°C) fixed
temperature alarm. The FST-851R incorporates a thermal rate of rise of 15°F (8.3°C). The
FST-851H is a high temperature sensor with 190°F (87.8°C) fixed temperature alarm. Both
models models support FlashScan or CLIP mode. (Earlier versions named FST-751 and FST-751R
also supported FlashScan or CLIP mode. Earlier models named FDX-551 and FDX-551R were
CLIP mode only.)
FSD-751P Photoelectric Duct Detector. The FSD-751RP includes an alarm relay. Both models
support FlashScan or CLIP mode.
FSD-751PL Low-flow Photoelectric Duct Detector, with extended speed range of 100–4000 FPM
(0.5 m/s to 20.3 m/s). FSD-751RPL adds a relay. Both models support FlashScan or CLIP mode.
FSH-751 (HARSH™) A special smoke detector that provides early warning smoke detection in
hostile environments where traditional smoke detectors are not practical. Supports FlashScan or
CLIP mode. (An earlier model named HPX-751 was CLIP mode only.)
FSL-751 VIEW® An advanced intelligent photoelectric detector that uses a laser diode, special
optics, and signal processing to obtain extremely high sensitivity. Supports FlashScan and CLIP
mode; compatible with AFP-300/AFP-400, NFS-640, and NFS-3030/NFS2-3030 only. LPX-751L
is compatible with AFP-200 and AM2020/AFP1010; CLIP mode only. (An earlier version named
LPX-751 was CLIP mode only and compatible with AFP-300/AFP-400.)
1.6.8 Addressable Manual Pull Stations

The NBG-12LX is a dual-action pull station that, when activated, provides an addressable
identification and its location to the control panel. An addressable monitor module is mounted
inside the pull station to facilitate servicing and replacement. Supports Flashscan or CLIP mode.
An earlier model named BGX-101L was CLIP mode only.
1.6.9 RFX Wireless Interface

The RFX Wireless Interface allows communication between an intelligent addressable fire alarm
control panel and up to 80 wireless smoke detectors. The RFX Interface, which includes a wireless
receiver, monitors the status of each wireless detector and forwards this information to the control
panel through the SLC. This system uses the SDRF-751 Wireless Photo-Thermal Smoke Detector,
which is battery-powered and designed to operate with the RFX Wireless Interface. FlashScan
capable. Not suitable for Canadian applications.
1.6.10 ACPS-2406 Addressable Charger/Power Supply

The ACPS-2406 is an auxiliary power supply and battery charger. Each of its four Notification
Appliance Circuits (NAC) is individually addressable, eliminating the need for control modules. In
addition, each circuit can provide notification appliance synchronization. FlashScan and CLIP
capable.

SLC Capacity Introduction
1.6.11 AMPS-24/E Addressable Power Supply

The AMPS-24/E is a primary power supply and battery charger. Depending on its configuration, it
can occupy either one or four addresses on an SLC. FlashScan capable.
1.7 SLC Capacity

The protocol selected for an SLC loop determines the maximum number of devices that can be
handled by the loop (see Section 1.5, “Polling Protocols”, on page 11). Within those limits, the
individual control panel may have additional restrictions. See the specific installation manual for
this information.
1.8 SLC Performance

SLC performance (Style 4, Style 6, or Style 7) depends on the configuration of the circuit and the
components on the circuit (see Table 1.2). SLC operation meeting Style 7 requirements isolates
each addressable device on the SLC from faults that may occur on the SLC.
Wiring style requirements are determined by national and local codes. Consult with the Authority
Having Jurisdiction before wiring the SLC. The table below (derived from NFPA 72-2002) lists the
trouble conditions that result when a fault exists on an SLC. Additional information is broken out
in Section 2, “Wiring Requirements”, on page 17, and Section 3, “Shielded Wire Termination”, on
page 25.
Type of Fault Style 4 Style 6 Style 7
Single Open Trouble Alarm, Trouble Alarm, Trouble

Single Ground Alarm, Trouble (ground) Alarm, Trouble (ground) Alarm, Trouble (ground)
Short Trouble Trouble Alarm, Trouble
Short and open Trouble Trouble Trouble
Short and ground Trouble Trouble Alarm, Trouble
Open and ground Trouble Alarm, Trouble Alarm, Trouble
Communications loss Trouble Trouble Trouble
• Trouble - The control panel will indicate a trouble condition for this type of fault.
• Alarm - The control panel must be able to process an alarm input signal in the presence of this type of fault.
Table 1.2 SLC Circuit Configuration and Performance: Style 4, Style 6, Style 7

Introduction LED Operation
1.9 LED Operation

The table below lists the LED operation on the various devices of an SLC in CLIP (Classic Loop
Interface Protocol) Mode and FlashScan® Mode. When switching from FlashScan® to CLIP
mode, the loop circuit must be powered down for at least 30 seconds to reset devices to CLIP mode
LED operation.
CLIP Mode FlashScan® Mode
Control Panel Device Standby Activated Standby Activated
AM2020 Monitor Module Blinks RED RED continuous N/A N/A

AFP1010 Control Module Blinks GREEN 2 sec. GREEN, then N/A N/A
Detector Blinks RED OFF N/A N/A
RED continuous
AFP-300/AFP-400 Monitor Module Blinks RED RED continuous N/A N/A

Control Module Blinks GREEN GREEN continous N/A N/A
Detector Blinks RED RED continuous N/A N/A
AFP-100 Monitor Module Blinks RED RED continuous N/A N/A

AIM-200 Control Module Blinks GREEN Blinks GREEN N/A N/A
AFP-200 Monitor Module Blinks RED RED continuous N/A N/A

Control Module Blinks GREEN OFF N/A N/A
NFS-640/E Monitor Module Blinks RED RED continuous Blinks GREEN RED continuous
NFS2-3030, Control Module Blinks GREEN GREEN continuous Blinks GREEN GREEN continuous
NFS-3030 Detector Blinks RED RED continuous Blinks GREEN RED continuous
NOTE: In CLIP mode, the LPX-751 and HPX-751 blink GREEN in standby and stay RED when
activated.

Section 2: Wiring Requirements
2.1 Recommended SLC Wiring

Depending on the panel, there are two recommended options for SLC wiring:
• Twisted, unshielded pair: NFS-640, NFS2-3030, NFS-3030, LCM-320, LEM-320, LIB-200A,
LIB-400.
Maximum resistance 50 ohms per branch. See Table 2.1.
Maximum capacitance: 0.5 µFarads per branch.
• Twisted-shielded pair: AFP-100, AFP-200, AFP-300/400, LIB-200, AIM-200.
Maximum resistance 40 ohms per branch. See Table 2.2.
To maximize distance on the SLC loop, use the recommended type of wire. Using other wiring
types makes the SLC circuit more susceptible to electrical interference and thus reduces its
maximum loop length.
FACP: Recommended
Wire Gauge†
Wire Type and Limitations* Max. Distance
LIB-200A or LIB-400 on AM2020/AFP1010 (See Table 2.2 for LIB-200.)
Twisted unshielded pair, 12 to 18 AWG 12,500 ft. (3,810 m) 12 AWG/3.31 mm²

(3.31 mm² to 0.82 mm²†). 50 ohms 9,500 ft. (2,895.6 m) 14 AWG/2.08 mm²
max per length of Style 6 and 7 loops. 6,000 ft. (1,828.8 m) 16 AWG/1.31 mm²
50 ohms per branch max for Style 4 3,700 ft. (1,127.76 m) 18 AWG/0.82 mm²
loops
NOTE: Twisted-shielded pair or untwisted unshielded wire is not recommended for use with LIB-200A or LIB-400.
NFS-640 and LEM-320 on NFS-640
Twisted-unshielded pair, 12 to 18 AWG 12,500 ft. (3,810 m) 12 AWG (3.31 mm²)

(3.31 mm² to 0.82 mm²). 50 ohms 9,500 ft. (2,895.6 m) 14 AWG (2.08 mm²)
maximum per length of Style 6 & 7 6,000 ft. (1,828.8 m) 16 AWG (1.31 mm²)
loops. 50 ohms per branch maximum 3,700 ft. (1,127.76 m) 18 AWG (0.82 mm²)
for Style 4 loop.
Untwisted, unshielded wire, in conduit 1,000 ft. (304.8 m) 12 to 18 AWG (3.31 mm² to 0.82 mm²)
or outside of conduit.
Note: Twisted-shielded pair is not recommended for use with this panel.
Note: Maximum total capacitance of all SLC wiring (both between conductors and from any conductor to ground) should not
exceed 0.5 microfarads.
LCM-320, LEM-320 on NFS-3030 or NFS2-3030
Twisted-unshielded pair, 12 to 18 AWG 12,500 ft. (3,810 m) 12 AWG (3.31 mm²)

(3.31 mm² to 0.82 mm²). 9,500 ft. (2,895.6 m) 14 AWG (2.08 mm²)
50 ohms, maximum per length of Style 6,000 ft. (1,828.8 m) 16 AWG (1.31 mm²)
6 & 7 loops. 50 ohms per branch 3,700 ft. (1,127.76 m) 18 AWG (0.82 mm²)
maximum for Style 4 loop.
Untwisted, unshielded wire, in conduit 1,000 ft (304.8 m) 12 to 18 AWG (3.31 mm² to 0.82 mm²)
Twisted, shielded pair 10,000 ft. (3,048 m) 12 to 18 AWG (3.31 mm² to 0.82 mm²)
Table 2.1 Wiring Recommendations: NFS-640, NFS-3030/NFS2-3030, LCM-320, LEM-320, LIB-200A,

and LIB-400
* XPIQ-SLI is an SLC device that provides an additional local SLC loop. This local SLC loop should use the same type of
wire recommended for the FACP controlling the main SLC loop. Maximum resistance of the local SLC (from any device
to FACP): 50 ohms. Maximum resistance of the local SLC (from any device to XPIQ-SLI): 20 ohms. (Maximum number
of detectors and modules = 64) Maximum SLC local branch current degraded mode: 20 mA. Maximum distance of local
loop: 2,000 ft. (600 m). Recommended wire: 12 AWG (3.31 mm²)

Wiring Requirements Recommended SLC Wiring
† Notifier brand cable is recommended; see the product catalog available from Paige Electric.
FACP: Recommended
Wire Type and Limitations Max. Distance Wire Gauge*
AFP-100
Twisted, shielded pair, 40 ohms 10,000 ft. (3,000 m) 12 AWG (3.31 mm²)
maximum per length of Style 6 and 7 8,000 ft. (2,400 m) 14 AWG (2.08 mm²)
loops. 40 ohms per branch maximum 4,875 ft. (1,450 m) 16 AWG (1.31 mm²)
for Style 4 loops. 3,225 ft. (980 m) 18 AWG (0.82 mm²)
Untwisted, Unshielded 1,000 ft. (300 m) 12-18 12 to 18 AWG (3.31 mm² to 0.82 mm²)
Note: Twisted-unshielded pair wire is not recommended for use with this panel.
AFP-200
Twisted-shielded pair. 40 ohms 10,000 ft. (3,048 m) 12 AWG (3.31 mm²)

maximum per length of Style 6 and 7 8,000 ft. (2,438.4 m) 14 AWG (2.08 mm²)
loops. 40 ohms per branch maximum 4,875 ft. (1,485.9 m) 16 AWG (1.31 mm²)
for Style 4 loops 3,225 ft. (982.98 m) 18 AWG (0.82 mm²)
or outside of conduit
Note: Maximum total capacitance of all SLC wiring (both between conductors and from any conductor to earth) should not exceed
0.5 microfarads.
AFP-300/AFP-400
Twisted-shielded pair, 12 to 18 AWG. 10,000 ft. (3,048 m) 12 AWG (3.31 mm²)

40 ohms, maximum per length of Style 8,000 ft. (2,438.4 m) 14 AWG (2.08 mm²)
6 and 7 loops. 40 ohms per branch 4,875 ft. (1,485.9 m) 16 AWG (1.31 mm²)
maximum for Style 4 loops. 3,225 ft. (982.98 m) 18 AWG (0.82 mm²)
LIB-200 on AM2020/AFP1010 (See Table 2.1 for LIB-200A or LIB-400.)
Twisted-shielded pair. Maximum loop 10,000 ft. (3,048 m) 12 AWG (3.31 mm²)
resistance is 40 ohms. Maximum 8,000 ft. (2,438.4 m) 14 AWG (2.08 mm²)
length is 10,000 ft. per channel (NFPA 4,875 ft. (1,485.9 m) 16 AWG (1.31 mm²)
Style 4) or 10,000 ft. total twisted pair 3,225 ft. (982.98 m) 18 AWG (0.82 mm²)
length (NFPA Style 6 and 7). Maximum
loop current is 200 mA (short circuit) or *If the wiring connected to the LIB-200 leaves the building it must be in conduit. It can
100 mA (normal). not exceed 1000 m (1093 yards), must not cross any power lines, and must not be in the
vicinity of any high voltage. These outdoor wiring restrictions do not apply to the
LIB-200A or the LIB-400.
System 5000 with AIM-200
Twisted-shielded pair. Maximum loop 10,000 ft. (3,048 m) 12 AWG (3.31 mm²)
resistance: 40 ohms. 8,000 ft. (2,438.4 m) 14 AWG (2.08 mm²)
Maximum loop voltage: 27.6 VDC. 4,875 ft. (1,485.9 m) 16 AWG (1.31 mm²)
Maximum loop current: 200 mA (short 3,225 ft. (982.98 m) 18 AWG (0.82 mm²)
circuit) or 100 mA (normal operation).
Table 2.2 Wiring Recommendations: AFP-100, AFP-200, AFP-300/400, LIB-200, AIM-200

* Notifier brand cable is recommended; see the product catalog available from Paige Electric.

Two-Wire SLC - Style 4 (Class B) Wiring Requirements
2.2 Two-Wire SLC - Style 4 (Class B)

2.2.1 Measuring Loop Resistance
T-tapping of the SLC wiring is permitted for two-wire Style 4 configurations. The total DC
resistance from the control panel to each branch end cannot exceed
• 50 ohms for LIB-200A, LIB-400, NFS-640, LCM-320, and LEM-320
• 40 ohms for AFP-100, AFP-200, AFP-300/400, LIB-200, AIM-200
Measure DC resistance as detailed and shown below:
1. With power removed, short the termination point of one branch at a time and measure the DC
resistance from the beginning of the SLC to the end of that particular branch.
2. Repeat this procedure for all remaining branches in the SLC
In Figure 2.1, Branches A, B, and C all begin at the SLC terminal, even though Branch B is
T-tapped.
Branch A Branch B Branch C
SLC Out
SLC-meas5.cdr
Branch
Short Point SLC Terminal

Block
B+ B–
Figure 2.1 Measuring DC Resistance of a Two-Wire SLC
2.2.2 Measuring Total Wire Length

The total wire length of all combined branches of one SLC cannot exceed the limits set forth in
each system’s instruction manual. Determine the total length in each SLC by summing all wire
segments. In Figure 2.1 above, the picture on the right shows an SLC with 3 branches. Figure 2.2
below shows the same SLC divided into segments. The total length of the SLC is determined by
adding the lengths of Segment 1 + Segment 2 + Segment 3 + Segment 4 + Segment 5. No segment
should be summed twice.
Branch A Branch B Branch C
Segment
Segment
Five
Four
Segment
Segment Segment
SLC-meas2.cdr
Three
One Two
SLC Terminal Block
Figure 2.2 Measuring the Total Wire Length of a Two-wire SLC

Wiring Requirements Four-Wire SLC Style 6 & 7 (Class A)
2.3 Four-Wire SLC Style 6 & 7 (Class A)

2.3.1 Measuring Loop Resistance
The total DC resistance of the SLC pair cannot exceed
• 50 ohms for LIB-200A, LIB-400, NFS-640, LCM-320, and LEM-320
• 40 ohms for AFP-100, AFP-200, AFP-300/400, LIB-200, AIM-200
Measure DC resistance as detailed and shown below:
1. Disconnect the SLC channel B (Out) and SLC channel A (Return) at the control panel.
2. Short the SLC at the last device and measure the resistance at SLC Out. Record resistance and
remove the short.
3. Short the SLC at the first device and measure the resistance at SLC return. Record resistance
and remove the short.
The maximum DC resistance of the SLC is the higher of 2 and 3.
SLC Out First Device
STEP 2
Last Device
SLC Return
Short Point
SLC Out
SLC-meas5.cdr
First Device
STEP 3
SLC Return
Last Device
Figure 2.3 Measuring DC Resistance of a Four-Wire SLC
2.3.2 Measuring Total Wire Length

The total wire length in a four-wire SLC cannot exceed the limits set forth in each system’s
instruction manual. The figure below identifies the output and return loops from SLC terminal on
the control panel:
SLC channel B SLC channel A

(output loop) (return loop)
SLC Terminal Block

B+ A+ B– A–
Figure 2.4 Measuring the Wire Length of a Four-Wire SLC

Control Panel Terminal Blocks Wiring Requirements
2.4 Control Panel Terminal Blocks

2.4.1 NFS2-3030 and NFS-3030 with LCM-320, LEM-320
The NFS-3030/NFS2-3030 supports up to five pairs of loop control and expander modules,
providing from one to ten SLC loops. Loops can be either CLIP mode or FlashScan mode. SLC
loops connect to TB1 on the LCM-320 or LEM-320.
B+ A+ B- A- TB1 B+ A+ B- A- TB1
LEM320-SLC-TB.cdr
SLC Loop Connections SLC Loop Connections
on Loop Control Modules on Loop Expander Module
Figure 2.5 NFS2-3030, NFS-3030 SLC Loop Connections and Wiring
2.4.2 NFS-640 with LEM-320

The NFS-640 provides one SLC loop and supports a second using optional expander module
LEM-320. Loops can be either CLIP mode or FlashScan mode. SLC loop #1 connects to TB16 on
the control panel; SLC loop #2 connects to TB1 on the LEM-320.
nfs640-slc-tb.cdr, LEM320-slc-tb.cdr
SLC1
B+ A+ B- A-
B+ A+ B- A- TB1
TB16
SLC Loop #1 Connections SLC Loop #2 Connections
on FACP’s main circuit board on Loop Expander Module
Figure 2.6 SLC Loop Connections and Wiring
2.4.3 AFP-100
AFP-100 supports one SLC loop; the loop is CLIP mode only. The SLC loop connects to TB6.
slc-100.wmf
SLC Loop Connections on AFP-100
Figure 2.7 SLC Connections for AFP-100
2.4.4 AFP-200
AFP-200 supports one SLC loop; the loop is CLIP mode only. The SLC loop connects to TB5.
slc-200.wmf
SLC Loop Connections on AFP-200
Figure 2.8 SLC Connections for AFP-200

Wiring Requirements Control Panel Terminal Blocks
2.4.5 AFP-300/AFP-400
AFP-300 supports one SLC loop; AFP-400 supports two SLC loops. The loops are CLIP mode
only. SLC loops connect to TB6 on AFP-300; SLC loops connect to TB5 and TB6 on AFP-400.
slc-300.wmf, slc-400.wmf
SLC Loop Connections SLC Loop Connections
on AFP-300 on AFP-400
Figure 2.9 SLC Connections for AFP-300/AFP-400
2.4.6 AM2020/AFP1010 with LIB-200A or LIB-400

AM2020/AFP1010 supports up to ten SLC loops using LIB-200A (one SLC loop per board) and/or
LIB-400 (one or two SLC loops per board). The loops are CLIP mode only. SLC loops connect to
TB1 and TB2 on LIB-400, and TB1 on LIB-200A.
Pin 1 SLC Loop Port A+
Pin 3 SLC Loop Port A-
Pin 5 SLC Loop Port B+
Pin 7 SLC Loop Port B-

Pin 8 Earth Ground
Pin 1 SLC Loop Port A+ Pin 1 SLC Loop Port A+
slc-lib-200a.wmf,slc-lib-400.wmf
Pin 3 SLC Loop Port A- Pin 3 SLC Loop Port A-
Pin 5 SLC Loop Port B+ Pin 5 SLC Loop Port B+
Pin 7 SLC Loop Port B- Pin 7 SLC Loop Port B-

Pin 8 Earth Ground Pin 8 Earth Ground
LIB-200A LIB-400
NOTE: LIB-200 has been replaced by LIB-200A.
Figure 2.10 SLC Connections for LIB-200A & LIB-400

Control Panel Terminal Blocks Wiring Requirements
2.4.7 System 5000 with AIM-200

System 5000 with AIM-200 supports one SLC loop; the loop is CLIP mode only. The SLC loop
connects to P8 on AIM-200.
slc-aim-200.wmf
Figure 2.11 SLC Connections for AIM-200
NOTE: AFC-600 has been discontinued; to service existing installations of this panel, refer to
the original manuals shipped with the panel.

Notes

Section 3: Shielded Wire Termination
3.1 Overview
This section shows the proper termination of the shield, if used.
Shielding of the SLC is recommended for use with AFP-100, AFP-200, AFP-300/400, LIB-200,
and AIM-200. Proper termination of the shield depends on the type of conduit used:
• Section 3.2, “No Conduit”.
• Section 3.3, “Full Conduit” (Canadian requirement).
• Section 3.4, “Partial Conduit”.
Shielding of the SLC is not recommended for use with NFS-640/E, NFS-3030/NFS2-3030,
LCM-320, LEM-320, LIB-200A or LIB-400. If twisted-shielded wire is used in one of these
installations, use a floating shield to terminate the wire as shown in Section 3.5, “Floating Shield”,
on page 27.
Use of good wiring practice consistent with local electrical codes is expected.
3.2 No Conduit
For use with AFP-100, AFP-200, AFP-300/400, LIB-200, and AIM-200 only
Scrape the paint on the cabinet to bare metal to provide a good electrical connection. Fold the foil
and drain wire back over the cable jacket. Slide the cable into the connector clamp and secure. The
drain wire should be connected to the connector screw. Do not allow the shield drain wire or foil to
enter the system cabinet.
Connector Screw
Shield Drain Wire
Cabinet
Foil
SLC-swterm1.cdr
Figure 3.1 Shield Termination – No Conduit

Shielded Wire Termination Full Conduit
3.3 Full Conduit

For use with AFP-100, AFP-200, AFP-300/400, LIB-200, and AIM-200 only
Connect the metal conduit to the cabinet by using the proper connector. Feed the shielded wire
through the conduit, into the control box. The shield drain wire must be connected to the
“reference” or “shield” terminal on the SLC terminal block, or connected to the negative side of the
loop if there is no “reference” or “shield” terminal on the SLC terminal block. Do not let the shield
drain wire or the shield foil touch the system cabinet or be connected to earth ground at any point.
Shield Drain Wire

Example at right illustrates Cabinet
shield drain wire connection Foil
to an SLC terminal block with
a “reference” connection.
Conduit
Shield2.wmf, SLC-swterm2a.wmf
Cabinet Foil Tape over foil.
Example at right illustrates –

shield drain wire connection
to an SLC terminal block Conduit
without a “reference” or
“shield” connection. +
Shield Drain Wire
NOTE: For Style 6 or Style 7 SLC wiring, connect one end of the shield to the
reference/negative side of the respective channel
Figure 3.2 Shield Termination – Full Conduit
3.4 Partial Conduit

For use with AFP-100, AFP-200, AFP-300/400, LIB-200, and AIM-200
If the length of conduit from the control panel cabinet is less than 20 ft. (6.1 m), terminate the
shield as shown. If using a metal box, you must use a metal conduit.
Connect the shielded wire to the junction box by using a proper connector. Scrape the paint on the
cabinet to bare metal to provide a good electrical connection. Connect the metal conduit between
the junction box and the cabinet by using the proper connectors.
Feed the twisted-pair wire into the junction box, through the conduit, into the cabinet box. Within
the junction box, connect the appropriate wires together using wire nuts. Connect the shield drain
wire to the junction box, at the end of the conduit run, as shown below.
Do not allow the shield drain wire to enter the system cabinet or the conduit.
Foil Shield Drain Wire
Cabinet
SLC-swterm3.cdr
Conduit
Figure 3.3 Shield Termination – Partial Conduit

Floating Shield Shielded Wire Termination
3.5 Floating Shield

If using shielded wire with NFS-640/E, NFS2-3030, NFS-3030, LCM-320, LEM-320,
LIB-200A and LIB-400
Twisted-unshielded wire is recommended for NFS-640/E, NFS2-3030, NFS-3030, LCM-320,
LEM-320, LIB-200A and LIB-400. If twisted-shielded pair wire is used in these installations, use
a floating shield to terminate the wire. The following precautions must be met:
• If the SLC is more than 3000 ft. (914.4 m), divide the shield into floating segments of less than
1000 ft. (304.8 m).
• To divide the shield wire into floating segments, cut shield even with jacket and tape as shown:
Tape
SLC-swterm4.cdr
NOTE: Using shielded wire in applications where it is not recommended will reduce the maximum
SLC length. If shielded wire must be used where not recommended, failing to float the ends will
reduce the maximum SLC length even further.
Figure 3.4 Floating the Shield

Notes

Section 4: SLC Circuits without Isolators
4.1 Overview
This chapter concerns itself with the two styles of circuits that do not require isolation devices:
• NFPA 72 Style 4
• NFPA 72 Style 6
4.2 NFPA Style 4 SLC

NFPA Style 4 requirements can be met by using the diagram below.
• T-tapping of the SLC wiring is allowed for Style 4 configuration.
Two-wire Addressable Detector
Addressable Module
T-tapped Circuits
B+ B–
SLC-style4.cdr
Control Panel
SLC
Figure 4.1 Basic NFPA Style 4 SLC

SLC Circuits without Isolators NFPA Style 6 SLC
4.3 NFPA Style 6 SLC

NFPA Style 6 requirements can be met by using the diagram below.
SLC Out
Addressable Module
SLC Return
B+ B– A– A+
SLC-style6.cdr
Control Panel
SLC
NOTE: T-tapping of the SLC wiring is NOT allowed for Style 6 configuration.
Figure 4.2 Basic NFPA Style 6 SLC

Section 5: SLC Circuits with Isolators
5.1 Overview
There are two isolator devices used to protect critical elements of the FlashScan-mode or
CLIP-mode SLC loop from faults on other SLC branches or segments.
• Fault Isolator Module ISO-X
• Isolator Detector Base B224BI
A Fault Isolator Module on both sides of a device, or the combination of an Isolator Base and
Isolator Module are required to comply with NFPA Style 7 requirements.
CAUTION:
! If relay or sounder bases are not used, a maximum of 25 addressable devices can be connected
between Isolator Modules and/or Bases. When relay or sounder bases are used, the maximum
number of addressable devices that can be connected between Isolators is reduced to seven.
Isolator modules will not function properly when these limits are exceeded.
When more than 100 Isolator Modules and/or Isolator Bases are connected from the AFP-300 or
AFP-400 to an SLC loop, the address capacity of the loop is reduced by two (2) addresses for every
isolator device in excess of 100.
The address capacity of the loop is reduced by two (2) addresses for every isolator device in excess
of 200 when the Isolator Modules and/or Isolator Bases are connected to the SLC loop from the
NFS2-3030, NFS-3030, NFS-640/E, AFP-100 or AFP-200.
5.2 Fault Isolator Module

The ISO-X module continuously monitors the circuit connected to terminals 3(–) and 4(+). Upon
powerup, an integral relay is latched on. The module periodically pulses the coil of this relay. A
short circuit on the SLC resets the relay. The module detects the short and disconnects the faulted
SLC branch or segment by opening the positive side of the SLC (terminal 4). This isolates the
faulted branch from the remainder of the loop preventing a communication problem with all other
addressable devices on the remaining branches (labeled “Continuation of the SLC” in the figure
below). During a fault condition, the control panel registers a trouble condition for each
addressable device which is isolated on the SLC segment or branch. Once the fault is removed, the
module automatically reapplies power to the SLC branch or segment.

SLC Circuits with Isolators Isolator Detector Bases
5.2.1 Wiring an Isolator Module

Figure 5.1 shows a Style 4 example for wiring of an Isolator Module.
Continuation
of the SLC
IN
IN
OUT
OUT
SLC-isowire.cdr
SLC Isolated branch
of theSLC
Figure 5.1 Wiring the ISO-X Module
5.3 Isolator Detector Bases

Isolator detector bases prevent an entire communications loop from being disabled when a short
circuit occurs. This is accomplished by isolating that part of the loop containing the short from the
remainder of the circuit. These bases also automatically restore the entire loop when the cause of
the short circuit is corrected.
B224BI is an intelligent isolator base used with Flashscan® detectors and most CLIP mode
detectors.

Isolator Detector Bases SLC Circuits with Isolators
5.3.1 How an Isolator Base Works

If a short circuit fault occurs at point “X”, devices A, B, C & detector 2 will cease to function and
display a trouble warning at the control panel. Devices D, E, F & detectors 1, 3, 4, and 5 will
remain normal as they are served by ‘SLC Return’.
If a short circuit fault occurs at point “Y”, all devices will continue to function.
If a short circuit fault occurs at point “Z”, only detector 4 will cease to function.
Detector 1 X Detector 2
Y
Detector 5 Z
Detector 4 Detector 3
SLC Out SLC Return
SLC-isowork.wmf
Control Panel
Isolator Base Non-Isolating Device Short-circuit path
NOTE: For information on wiring an isolator base, refer to Figure 9.3, “Wiring an Isolator Base”
on page 55.
Figure 5.2 Isolator Base Circuit: Sample Style 6 Wiring

SLC Circuits with Isolators NFPA Style 4 SLC Using Isolator Modules
5.4 NFPA Style 4 SLC Using Isolator Modules

A variation of a Style 4 operation using isolator modules to protect each branch of the SLC. Refer
to Figure 5.1 on page 32 for ISO-X wiring and to Section 5.1, “Overview” for limitations.
Isolator Module
Isolated Branch
Isolator Module
Isolated Branch
Addressable Pull Station
Isolator Module
Isolated Branch
B– B+
SLC-style4iso.cdr
Control Panel
SLC
Figure 5.3 NFPA Style 4 SLC Using ISO-X Modules

NFPA Style 6 SLC Using Isolator Modules SLC Circuits with Isolators
5.5 NFPA Style 6 SLC Using Isolator Modules

A variation of Style 6 operation using isolator modules to protect a section of the SLC. By flanking
each group of devices with ISO-X fault isolator modules each group is protected from faults that
may occur in the other groups. For example, a fault in Section B will not affect Sections A & C.
The isolator modules on either side of Section B will open the loop. Section A will still operate
from power on the SLC Out side and Section C will operate from the SLC Return side.
• A combination of isolator modules and isolator bases may be used.
• T-tapping is NOT allowed within the Style 6 configuration.
• Isolator modules shall be within 20 ft. (6.1 m) of device and the wire must be enclosed in metal
conduit.
Isolator Isolator
Module Module
Section B
Two-wire
Addressable Section C
Detector
Addressable
Pull Station
Section A
Additional isolator module required when first device in the

section is more than 20 feet from the control panel.
Isolator Isolator
Module Module
The first isolator module on SLC Out and SLC Return is not
Isolator required for AFP-300, AFP-400, NFS-640/E, or Isolator
Module NFS-3030/NFS2-3030 because the panels provide the Module
functionality.
SLC Out SLC Return
AFP-100, AFP-200, AM2020/AFP1010,

SLC-style6iso.cdr
System 5000 with AIM-200: The first

isolator module on SLC Out and SLC
Return must be contained within the same Control Panel
enclosure as the FACP, or these isolator
modules must be connected within 20 ft.
(6.1 m) of the FACP enclosure in conduit.
Figure 5.4 NFPA Style 6 SLC Using ISO-X Modules

SLC Circuits with Isolators NFPA Style 7 SLC Using an Isolating Device
5.6 NFPA Style 7 SLC Using an Isolating Device

Style 7 operation requires using a combination of isolator detector bases and isolator modules or
isolator modules before and after a non-isolator device. Flanking each device with an isolator
provides fault protection to all other devices on the loop.
• T-tapping is NOT allowed within the Style 7 wiring configuration.
• When a non-isolator base or pull station is used, install isolator modules on both sides of
devices.
• When an isolator base is used in conjunction with an isolator module, install the isolator
module as shown in Figure 9.3.
• There must be a close-nipple connection between a device and the isolator bases or modules
that protect it.
Isolator
Module
Two-wire Isolator
Detector Base
Isolator Isolator
Module Module
Addressable
Pull Station
Addressable
Detector
Isolator Isolator
Module Module
The first isolator module on SLC Out and SLC Return is

not required for AFP-300, AFP-400, NFS-640/E, or
Isolator NFS-3030/NFS2-3030 because the panels provide the Isolator
Module functionality. Module
SLC Out SLC Return
AFP-100, AFP-200, AM2020/AFP1010,

System 5000 with AIM-200: The first
isolator module on SLC Out and SLC
Return must be contained within the
same enclosure as the FACP, or these
SLC-style7iso.cdr
isolator modules must be connected

within 20 ft. (6.1 m) of the FACP
enclosure in conduit. Control Panel
NOTE: See Figure 9.3, “Wiring an Isolator Base” on page 55.
Figure 5.5 NFPA Style 7 SLC

Section 6: Monitor Modules
6.1 Description
These addressable modules monitor conventional contact-type alarm initiating devices. You can
configure module circuits as NFPA Style B (Class B) or Style D (Class A) Initiating Device
Circuits (IDC). There is no limit to the number of contact-type devices installed on a monitor
module IDC.
For more information on the individual module specifications refer to the Installation Instructions
that are provided with this device. For information on transponders, refer to the specific
transponder manual.
6.1.1 Addressable Monitor Module

FMM-1 is an addressable module that monitors either a Style B (Class B) or Style D (Class A) IDC
of dry-contact input devices. This module is capable of participating in degraded mode where
supported by the FACP.
6.1.2 Zone Interface Module

FZM-1 is similar to the FMM-1, except it is used to monitor compatible two-wire, 24 volt,
conventional (non-addressable) smoke detectors on a Style B (Class B) or Style D (Class A) IDC.
Rotary
Switches
IDC Return 9
IDC Return 8 SLC–
SLCModule-simplified.wmf
IDC Out 7 SLC+
24 VDC –
IDC Out 6
24 VDC +
} Zone interface modules only.
On addressable monitor modules in
FlashScan mode with NFS-640/E,
NFS2-3030, and NFS-3030, pins 3 & 4 can
Areas used to record the device be jumpered to enable the fire panel’s
address and SLC number. Communication Loss (Degraded mode)
feature.
Figure 6.1 FMM-1/FZM-1 Modules

Monitor Modules Description
6.1.3 Dual Monitor Module

FDM-1 is similar to the FMM-1, except intended for use in intelligent two-wire systems providing
two independent Style B (Class B) IDCs at two separate, consecutive addresses.
Rotary
Switches
Address +1 { 9 H–
8 H+ SLC–
SLCDualMod-simplified.wmf
SLC+
Base Address { 7L+
6L–
Areas used to record the device

address and SLC number.
Figure 6.2 Dual Monitor Module
6.1.4 Miniature Monitor Module

FMM-101 is intended to monitor a Style B (Class B) IDC; it is offered in a smaller package for
mounting directly in the electrical box of the device being monitored.
Rotary 14 15 0 1 ADDRESS 0 1 Label – Use to record the
Switches
13
12
2
3
2
3
device address and SLC
11 4
LOOP
4 number.
10 5 5
9 8 7 6 9 8 7 6
TENS ONES
IDC (+) Violet SLC (+) Red
SLC (-) Black
FMM-101.cdr
IDC (-) Yellow
Figure 6.3 Miniature Monitor Module

Setting an SLC Address for a Module Monitor Modules
6.2 Setting an SLC Address for a Module

FlashScan capable control or relay modules, as well as detectors, can be set to one of 159 addresses
(01-159) and are factory preset with an address of “00”. CLIP mode detectors and panels are
limited to addresses 01-99.
To set an SLC address, use a common screwdriver to adjust the rotary switches on the module to
the desired address. The unit shown in Figure 6.4 is set at address “35”. When finished, mark the
address on the module face in the place provided.
Rotary 6 7 8 9 10
Switches 5
4 11 Breakaway Tab - Modules come
3 12 with a raised breakaway tab on the
2 13
SLC-setadd.cdr, SLCbrktabs.cdr
1 0 1514 TENS rotary switch. This tab must
TENS
be removed when the module is on
an FACP that uses more than 99
addresses.
6789
5
4
3
2
10
ONES
Dual monitor modules: On dual monitor modules, only even

numbers appear on the ONES rotary switch. The module takes
both the selected address and the next-higher address.
Figure 6.4 Setting SLC Address on Module
6.3 NFPA Style B IDC Using Monitor Modules

Connect the SLC wiring to the module terminals 1 (–) and 2 (+). Each FMM-1 module takes one
address on the SLC. Use the rotary switches on the module to set it to the required SLC address.
The figure below shows typical wiring for a supervised and power-limited NFPA Style B (Class B)
Initiating Device Circuit using the FMM-1 monitor module.
Module installation notes:
1. The Initiating Device Circuit (IDC) is supervised and current-limited to 210 microamps
@ 24 VDC (nominal).
2. The IDC provides the following services (do not mix):
• Fire alarm service
• Automatic and manual waterflow alarm service with normally open contact devices
• Sprinkler supervisory service with normally open contact devices
• Security service
3. Refer to the Device Compatibility Document for compatible smoke detectors.
4. See “Power Considerations” on page 59 for information on supervising 24 VDC power.

Monitor Modules NFPA Style B IDC Using Monitor Modules
From Supply
24 VDC
Four-wire 24 VDC Power
Detector Base Filtered, Regulated,
Resettable
Manual pull
station
To Next IDC
or
47K ELR Supervision Device
(supplied
with module)
Heat SLC
detector
FMM-1
SLC-idcB1.wmf
IDC
NFS-640/E, NFS2-3030, and

NFS-3030 (FlashScan® only):
Jumper terminals 3 and 4 to enable
the fire panel’s Communication Loss
(Degraded mode) feature.
Figure 6.5 Typical Style B IDC Wiring with FMM-1

NFPA Style D IDC Using Monitor Modules Monitor Modules
6.4 NFPA Style D IDC Using Monitor Modules

Connect the SLC wiring to the module terminals 1 (–) and 2 (+).
Each FMM-1 module takes one address on the SLC. Use the rotary switches on the module to set it
to the required SLC address.
The figure below shows typical wiring for a supervised and power-limited NFPA Style D (Class A)
IDC using the FMM-1 module.
@ 24 VDC (nominal).
From
Supply
24 VDC
Four-wire
Detector Base 24 VDC Power
Filtered, Regulated,
Resettable
Manual pull
station
To Next IDC
or
Supervision Device
SLC
Heat
detector FMM-1
SLC-idcD1.cdr
IDC
NFS-640/E, NFS2-3030, and
NFS-3030 (FlashScan® only):
Jumper terminals 3 and 4 to enable
the fire panel’s Communication Loss
(Degraded mode) feature.
Figure 6.6 Typical Style D IDC Wiring with FMM-1

Monitor Modules NFPA Style B IDC Using Dual Monitor Modules
6.5 NFPA Style B IDC Using Dual Monitor Modules

Connect the SLC wiring to the FDM-1 module terminals 1 (–) and 2 (+).
Use the rotary switches on the module to set it to the required SLC address. Each dual module takes
two addresses on the SLC. Circuit ‘L’ corresponds to the address set on rotary switches. Circuit ‘H’
will automatically respond at the next higher address. The Circuit L “base address” is always an
even number; the lowest possible address is 02. The Circuit H “base + 1” address is always odd.
Use caution to avoid duplicate addressing of modules on the system.
Each IDC (H & L) is power limited to 230 microamps @ 24 VDC.
Initiating Device Circuit using the FDM-1 dual monitor module.
@ 24 VDC (nominal).
Manual
Pull
Station
47K
ELR 47K
ELR
SLC
Heat
Detector
FDM-1
Base +1 Address
SLC-idcB3fdm1.wmf
Base Address (IDC Circuit H)

(IDC Circuit L)
Figure 6.7 Typical Style B IDC Wiring with FDM-1

NFPA Style B IDC Using Zone Interface Modules Monitor Modules
6.6 NFPA Style B IDC Using Zone Interface Modules

Connect the SLC wiring to the FZM-1 module terminals 1 (–) and 2 (+). Each module takes one
address on the SLC. Use the rotary switches on the module to set it to the required SLC address.
IDC using the FZM-1 module.
@ 24 VDC (nominal).
Two-wire
smoke
detectors 3.9K ELR
(supplied with module)
SLC
FZM-1
IDC
90 mA
External
SLC-idcB2.wmf
24 volt supply
required
24 VDC Resettable power.

(Resettable power is not necessary for the
NFS-640/E, NFS2-3030, or NFS-3030 when operating in
FlashScan mode.)
Figure 6.8 Typical Style B IDC Wiring with FZM-1

Monitor Modules NFPA Style D IDC Using Zone Interface Modules
6.7 NFPA Style D IDC Using Zone Interface Modules

Connect the SLC wiring to the FZM-1 module terminals 1 (–) and 2 (+).
Each module takes one address on the SLC. Use the rotary switches on the module to set it to the
required SLC address.
The figure below shows typical wiring for a supervised and power-limited NFPA Style D (Class A)
IDC using the FZM-1 zone interface module.
@ 24 VDC (nominal).
3.9K ELR
Two-wire (supplied with module)
smoke
detectors
SLC
FZM-1
IDC
90 mA
External
24 volt supply
required
SLC-idcD2.wmf
24 VDC Resettable power.

(Resettable power is not necessary for the
NFS-640/E, NFS2-3030, or NFS-3030 when
operating in FlashScan mode.)
Figure 6.9 Typical Style D IDC Wiring with the Zone Interface Module

Section 7: Control Modules
7.1 Description
The FCM-1 module is an addressable module that can be used for monitoring and switching 24
VDC Notification Appliance Circuit (NAC) power for NFPA Style Y (Class B) and NFPA Style Z
(Class A) circuits. It can also be used for audio/voice applications and fire-fighters telephone; these
two types of applications are documented separately. For UL 9th edition audio applications, refer
to the Digital Voice Command Manual and the Digital Audio Amplifiers Manual. For UL 8th
edition audio applications, refer to the Voice Alarm System Manual or FireVoice 25/50 Manual.
The module has a resistor on the back (refer to Figure 7.2) that must be removed when it is used on
an FFT-7 or FFT-7S telephone circuit.
For more information on the module specifications refer to the Installation Instructions provided
with this device.
Setting an SLC Address

Each module is factory preset with an address of “00.” To set an SLC address refer to “Setting an
SLC Address for a Module” on page 39.
7.2 Wiring a NAC with Addressable Control Modules

Figure 7.1 shows the connections to wire the FCM-1 module for powering a 24 VDC NAC.
Style Z NAC (+)

Style Z NAC (–) SLC (–)
Style Y/Z NAC (–) SLC (+)
Style Y/Z NAC (+) 24 VDC Nonresettable Power (–)*
SLCModule-simplified.wmf
24 VDC Nonresettable Power (+)*
Note: Module is shown in alarm condition.

*Can also be used in audio/voice and fire-fighters telephone applications (70.7 VRMS audio or telephone); refer
to the Voice Alarm System Manual, FireVoice 25/50 Manual, DVC Manual, or DAA Manual as appropriate for
your equipment.
Figure 7.1 FCM-1 Wiring Connections

Control Modules Wiring a NAC with Addressable Control Modules
This resistor must be

removed when using the
FCM-1 on an FFT-7 or
Label
FFT-7S telephone circuit
(see the Voice Alarm System
Manual, FireVoice 25/50
The label must be Manual, DVC Manual, or
cut and removed DAA Manual as appropriate
from over the for your equipment) and
recessed area to when supervising 24VDC
access the resistor. NAC power using the
no-relay alternative wiring
Remove the resistor, (see Appendix A.2.3, “Using
FMM-1back.cdr
then place a piece of the Addressable Control
tape over the Module Without Relay”).
recessed area.
NOTE: When using NFS2-3030/NFS-3030 and the Control type ID, do not cut this resistor.
Figure 7.2 FCM-1 Rear View - Resistor Location

Wiring a Style Y NAC (Two-Wire) with Addressable Control Modules Control Modules
7.3 Wiring a Style Y NAC (Two-Wire) with Addressable

Control Modules
A supervised and power-limited NFPA Style Y (Class B) Notification Appliance Circuit (NAC)
using the FCM-1 module. Polarized alarm notification appliances are shown connected to the
module in a two-wire configuration.
1. See “Power Considerations” on page 59 for information on monitoring 24 VDC power.
2. Each module can control 2 amps of resistive load (on electronic devices) or 1 amp of inductive
load (on mechanical bells and horns).
3. A power supervision relay is required only on the last module of the power run.
(NFS2-3030 and NFS-3030 only: If using one of the NFS2-3030/NFS-3030’s FlashScan type
IDs that provide built-in power supervision, no relay is required.)
4. Do not T-Tap or branch a Style Y circuit.
5. Terminate the circuit across the last device using a UL-listed End-of-Line Resistor 47K,
1/2-watt, SSD P/N A2143-00 (ELR-47K in Canada).
6. Do not loop wiring under the screw terminals of any notification appliance. To maintain
supervision, break the wire run at each device.
7. Refer to Device Compatibility Document for compatible notification appliances and relays.
SLC
FCM-1
ELR 24 VDC Notification

47K, 1/2-watt Appliances
A power supervision
relay is required only on
the last module of the
power run. (NFS2-3030
and NFS-3030 only: If
using one of the
NFS2-3030/NFS-3030’s
FlashScan type IDs that
NAC provide built-in power
supervision, no relay is
required.)
SLC-nacY.wmf
Module polarities are shown in alarm condition
24 VDC Nonresettable power
Figure 7.3 NFPA Style Y Notification Appliance Circuit

Control Modules Wiring a Style Z NAC (Four-Wire) with Addressable Control Modules
7.4 Wiring a Style Z NAC (Four-Wire) with Addressable

Control Modules
A supervised and power-limited NFPA Style Z (Class A) Notification Appliance Circuit (NAC)
using the FCM-1 module. Polarized alarm notification appliances are shown connected to the
module in a four-wire configuration.
2. Each module can control 2 amps of resistive load (on electronic devices) or 1 amp of inductive
load (on mechanical bells and horns).
3. A power supervision relay is required only on the last module of the power run.
(NFS-3030 only: If using one of the NFS-3030’s FlashScan type IDs that provide built-in
power supervision, no relay is required.)
4. Do not T-Tap or branch a Style Z circuit.
5. Do not loop wiring under the screw terminals of any notification appliance. To maintain
supervision, break the wire run at each device.
6. Refer to the Device Compatibility Document for compatible notification appliances and relays.
SLC
24 VDC
notification FCM-1
appliances
NAC Return
A power supervision relay
is required only on the last
NAC Out module of the power run.
(NFS2-3030 and
NFS-3030 only: If using
one of the
NFS2-3030/NFS-3030’s
FlashScan type IDs that
provide built-in power
supervision, no relay is
SLC-nacZ.wmf
required.)
Module polarities are shown in Alarm.

24 VDC Nonresettable power
Figure 7.4 NFPA Style Z Notification Appliance Circuit

Connecting a Releasing Device to the Addressable Control Module Control Modules
7.5 Connecting a Releasing Device to the Addressable

Control Module
The FCM-1module can control 1 A of current. Make sure to keep total system current within the
limits of the power supply. You can power the module from the power supply of the Control Panel
or any UL 864-listed 24 VDC regulated power-limited power supply for Fire Protective Signaling.
For more information, refer to the Device Compatibility Document.
SLC from FACP

or LEM-320
+
–
– +
Compatible UL-listed
24 VDC releasing device 9 0
6 7 8 9 10
5
8
4
3
11
12 1 Non-resettable
– 7
2
TENS
1 0 1514
13
2 24 VDC Power
6789
–
Relconn-fcm.cdr
5
Brown Red 6 4
3 3
+ 5
2
10
4
+
REL-47K ONES
ADDRESS
LOOP
(Use with Type Code
Rel Ckt ULC, N.C. Supervision
or see Circuit
Relay Contact Power Supervision
Requirement 3.)
Part of EOLR-1 Relay (EOLR-1)
FCM-1
Note: See text for circuit requirements.
Figure 7.5 Typical Connection of a 24 VDC Releasing Device to the FCM-1 Module
Circuit Requirements. When connecting a releasing device to the FCM-1 module, note the
following:
1. For NFPA 13 and 15 applications, disable the Soak Timer (Soak=0000).
For NFPA 16 applications, set the Soak Timer (0600-0900 seconds).
Refer to your FACP’s Programming Manual for instructions.
2. For applications using power-limited circuits:
a) Use an End-of-Line device (P/N REL-47K) with the FCM-1 module. Connect the
End-of-Line device as shown in Figure 7.5.
b) Program the releasing circuit for Type Code REL CKT ULC.
c) Circuits are supervised against opens and shorts.
3. For applications not requiring power-limited circuits –
a) End-of-Line devices (P/N REL-47K) are not required; however, the releasing device circuit
is not supervised against shorts.
b) In non-power-limited applications, program the releasing circuit for Type Code
RELEASE CKT
c) Limited energy cable cannot be used to wire a non-power-limited releasing device circuit.
d) Maintain a 0.25 inch (6.35 mm) spacing between the non-power-limited releasing circuit
device wiring and any power-limited circuit wiring.
The FCM-1 module must be programmed with the correct releasing type code listed in your
FACP’s Programming Manual.

Notes

Section 8: Relay Module
8.1 Description
The FRM-1 module is an addressable module that provides two isolated sets of Form-C relay
contacts.
Ratings for the dry relay contacts on a Form-C module are:
• Resistive – 2 amps @ 30 VDC (e.g. Electronic devices and strobes)
• Inductive – 1 amp @ 30 VDC (0.6pF) (e.g. Mechanical bells and horns)
• Pilot Duty – 0.5 amp @ 125 VAC (0.35pF) (e.g. Using a smaller relay to trip another relay)
For more information on the module specifications refer to the Installation Instructions provided
with this device. For information on transponders, refer to the specific transponder manual.
Setting an SLC Address

Each FRM-1 module is factory preset with an address of “00.” To set an SLC address refer to
Section 6.2, “Setting an SLC Address for a Module”, on page 39.
8.2 Wiring the Addressable Relay Module (Form-C Relay)

The figure below shows the FRM-1 module wired to the Control Panel.
SLC
FRM-1
C
NC
NO
C
NC NO
SLC-frmC.wmf
Figure 8.1 Relay Module Wiring Connections

Notes

Section 9: Intelligent Detector Bases
9.1 Description
The B501 and B710LP Detector Bases, the B224RB plug-in relay detector base, and the B501BH
sounder base provide the connection between the SLC and a variety of intelligent detectors. Use the
B710HD Detector Base with all HARSH™ detectors.
For more information refer to the Installation Instructions documents provided with these devices.
Setting the Detector Address

Each intelligent detector head is factory preset with an address of “00.” To set an SLC address refer
to “Setting an SLC Address for a Module” on page 39.
9.2 Wiring a Detector Base

Figure 9.1 shows typical wiring of a B501 detector base connected to an SLC. An optional
RA400Z Remote LED Annunciator is shown connected to the base.
SLC
Use a female disconnect

to wire the RA400Z (–) to
Terminal 1 (–).
To next device
on SLC
For connection of
cable shield
RA400Z
SLC-B501wire.wmf
Remote LED
Annunciator
(Optional)
NOTE: The B710LP base wiring is identical to the B501, except there is no shield terminal.
Figure 9.1 Wiring of a B501 Detector Base

Intelligent Detector Bases Wiring a Detector Base
Figure 9.2 shows typical wiring of a B710HD detector base (for use with a HARSH™ detector)
connected to an SLC. An optional RA400Z Remote LED Annunciator is shown connected to the
base.
SLC
To next device
on SLC
For connection of
cable shield
Power to next
To compatible device
UL Listed
Power Supply
RA400Z
Remote LED
Annunciator
(Optional)
B710HD.wmf
NOTE: Use a spade lug to wire the Remote LED Annunciator (–) to Terminal 2 (–).
Figure 9.2 Wiring of a B710HD Detector Base

Wiring an Isolator Base Intelligent Detector Bases
9.3 Wiring an Isolator Base

The Isolator Base will isolate its detector from short circuits that occur on the SLC connected at
terminals 3 and 2. It will not isolate its installed detector from short circuits that occur on the SLC
connected at terminals 1 and 2. In Style 7 applications, the loss of a single detector during a short
circuit is not acceptable, and an isolator module must be installed as shown in the figure below.
SLC Out
SLC In
Conduit
SLC-224BIwire.wmf
ISO-X
Isolator Module
Figure 9.3 Wiring an Isolator Base
9.4 Wiring a Relay Base

Figure 9.4 shows typical wiring of a B224RB plug-in relay detector base connected to an SLC.
To next device
on SLC
For connection of
cable shield
3 Relay Common
2 Normally Open
1 Normally Closed
SLC
b224rb.wmf
Figure 9.4 Wiring of a B224RB Plug-in Relay Detector Base

Intelligent Detector Bases Wiring a Sounder Base
9.5 Wiring a Sounder Base

Figure 9.5 shows typical wiring of the B501BH and B501BHT sounder bases.
OUT
+4 –5
4 5
3 21
IN External supply
-3 – 2 +1
Class A Optional Wiring

Intelligent
Monitor
Optional Sounder Interconnect* Module
SLC B+
UL-listed
Compatible
FACP UL-listed
EOL
SLC B- Resistor
47K
(-) Power
External (+) Power
24V
B501BHWiring.wmf
Supply
UL-listed
Class A Optional Wiring EOL Relay
24V
*Grouping of up to 6 model B501BHT temporal tone sounder bases.
Figure 9.5 Wiring of the B501BH/B501BHT Sounder Base

Section 10: Addressable Manual Pull Station
10.1 Description
The NBG-12LX is an addressable manual pull station with a key-lock reset feature.
For more information refer to the Installation Instructions document provided with this device.
Setting an SLC address

Each unit is factory preset with an address of “00.” To set an SLC address refer to “Setting an SLC
Address for a Module” on page 39.
10.2 Wiring a Manual Pull Station

Typical wiring for the NBG-12LX Manual Pull Station to an SLC.
–
To next device
+ on SLC
SLC +
–
US PAT 444 0991
SLC-nbg12.cdr
Figure 10.1 Wiring the NBG-12LX Pull Station to an SLC

Notes

Appendix A: Power Considerations
A.1 Supplying Power to 24 VDC Detectors and NACs

Resistance and Size
To determine the maximum allowable resistance that can be tolerated in supplying power to 24
VDC four-wire devices and NACs, use the calculations below. These simplified equations assume
that the devices are at the end of a long wire run. With the computed resistance and using the
manufacturers specifications for the desired wire, select the proper gauge wire for the power run.
For Four-Wire Detectors:
(Vms - Vom)
Rmax =
(N)(Is) + (Na)(Ia) + (Ir)
For NACs:
(Vms - Vom)
Rmax =
(Nb)(Ib)
Where:
Rmax = maximum resistance of the 24 VDC wires
Vms = minimum supply voltage (see Table A.1 below)
Vom = minimum operating voltage of the detector or end-of-line relay, whichever is greater, in volts
N = total number of detectors on the 24 VDC supply circuit
Is = detector current in standby
Na = number of detectors on the 24 VDC power circuit which must function at the same time in
alarm
Ia = detector current in alarm
Ir = end-of-line relay current
Nb = number of Notification Appliance Devices
Ib = Notification Appliance current when activated
NOTE: This simplified equation assumes that the devices are at the end of a long wire run.
The minimum supply voltages produced by Notifier power supplies are listed below:
FACP Vms Power Supply Vms
AFP-100 18.1 FCPS-24/E 19.1
AFP-200 19.4 FCPS-24S6/FCPS-24S8 19.1
NFS-640/E 19.15 MPS-24A/E 19.6
MPS-24B/E 20.1
MPS-400 19.23
ACPS-2406 19.8
AMPS-24/E 20.27
Table A.1 Minimum Supply Voltage

Power Considerations Supervising 24 VDC Power
A.2 Supervising 24 VDC Power

There are options for supervising 24 VDC power, as discussed below.
• Using FlashScan Type Codes with Built-In Power Supervision (NFS2-3030 and NFS-3030
only)
• Power Supervision Relay
• Using the FCM-1 module without relay
A.2.1 Using Type Codes with Built-In Power Supervision on

NFS2-3030 and NFS-3030
With LCM-320 revision 2.0 and higher, certain FlashScan type codes have external power
supervision built into the software. For details, refer to “Devices Requiring External Power
Supervision” in the NFS2-3030 Installation Manual or the NFS-3030 Installation Manual.
A.2.2 Power Supervision Relay

Power used to supply 24 VDC detectors, notification appliances (using the FCM-1) and two wire
detectors (using the FZM-1) can be supervised with a power supervision relay. This relay,
energized by the 24 VDC power itself, is installed at the end of each respective power run and
wired inline with the supervised circuit of any intelligent module.
When power is removed from the relay, the normally closed contacts open the supervised circuit,
generating a trouble condition. Therefore, the relay needs to be installed at the end of the
supervised circuit, so as to not disrupt the operating capability of all the devices on that circuit. The
relay can be installed inline with any leg (+ or –) of the supervised NAC or IDC circuit, either a two
or a four-wire style.
See Figure A.1 and Figure A.2. Refer to the Device Compatibility Document for compatible
notification appliances and relays.
Last device on the SLC loop

(FCM-1 or FZM-1)
ELR
(Use 47K with FCM-1
or 3.9K with FZM-1) Supervised NAC or IDC
Power Supervision
Relay
(EOLR-1)
SLC-psr.cdr
24 VDC Power from

Control Panel or
Power Supply
Figure A.1 Supervised 24 VDC Circuit

Supervising 24 VDC Power Power Considerations
FCM-1
24 VDC Power from

ELR 47K Supervised NAC or IDC Control Panel or Power Supply
Power Supervision
Relay
(EOLR-1)
FMM-1
SLC-psr-2address.cdr
Figure A.2 Alternate: 2-Address Method of Supervising a 24 VDC Circuit

Power Considerations Supervising 24 VDC Power
A.2.3 Using the Addressable Control Module Without Relay

An alternate method of supervising 24 VDC power fed to the Notification Appliance Circuit of the
FCM-1 module eliminates the need for a power supervision relay. This method uses a Notification
Appliance Circuit from the control panel or power supply to supply power to the FCM-1 modules.
The control panel supervises this circuit, which can be either a Style Y or Style Z.
Style Y NAC Power Wiring
Program the NAC from the control panel for general alarm. (Refer to the programming manual or
programming section of the FACP documentation for instructions.) Note that if the NAC is a coded
output, the FCM-1 output will be coded as well.
Refer to the Device Compatibility Document for compatible notification appliances.
• The circuit is supervised and power-limited.
• In this circuit, an external ELR is required at end of the NAC circuit.
• Refer to the respective control panel installation manual for NAC terminal block connection
information and ELR value.
• Remove internal resistor on each FCM-1 (see instructions in Figure 7.2 on page 46).
Connect the NAC power as follows:
FCM-1
End-of-line
Resistor
FCM-1
Circuit supervised
by control panel
SLC-nacY1.cdr
Note: Drawing shows power wiring

only; SLC Wiring not shown. NAC Terminal Block (24 VDC)
Figure A.3 NFPA Style Y NAC Power (Alternate)

Supervising 24 VDC Power Power Considerations
Style Z NAC Power Wiring (Alternate)

Program the NAC from the control panel for general alarm. (Refer to the programming manual or
programming section of the FACP documentation for instructions.) Note that if the NAC is a coded
output, the FCM-1 output will be coded as well.
Refer to the Device Compatibility Document for compatible notification appliances.
• The circuit is supervised and power-limited.
• In this circuit, an external ELR is not required at end of the NAC circuit.
• Refer to the respective control panel installation manual for NAC terminal block connection
information.
• Remove internal resistor on each FCM-1 (see instructions in Figure 7.2 on page 46).
Connect the NAC power as follows:
FCM-1
FCM-1
Circuit supervised
by control panel
SLC-nacZ1.cdr
Note: Drawing shows power wiring NAC Terminal Block

only; SLC Wiring not shown. (24 VDC)
Figure A.4 NFPA Style Z NAC Power (Alternate)

Notes

Appendix B: SLC Surge Suppression
B.1 Introduction
There are one primary and three secondary UL–listed surge protectors approved for use with the
FACPs listed in this appendix.
Primary Surge Protector:
• 326-2M TII Station Protector
Secondary Surge Protectors:
• DTK-2LVLP-F: Diversified Technology Group, Inc. (DITEK) 1720 Starkey Rd. Largo, FL
33771 (800) 753-2345.
• SLCP-30: EDCO 1805 N.E. 19th Ave. Ocala, FL 34470 (352) 732-3029
• PLP-42N: Northern Technologies, Inc. 23123 E. Madison Ave. Liberty Lake, WA 99019
(800) 727-9119
NOTE: For detailed information refer to the installation documentation supplied with the unit.
One primary surge protector must be used with each SLC wiring pair whenever SLC wiring runs
outside the building.
• Install primary protection only as shown in this document.
• Refer to NEC Article 800 and local building code requirements.
Additional primary surge suppressors may be added as required by the NEC. Add these additional
suppressors in series with the SLC wiring at the building entry/exit.
Wiring connected to the surge suppressor output must remain within the building while wiring
connected to the surge suppressor input may be routed outside the building as shown below.
Building #2 Building #1
P P
FACP
P = Primary
S = Secondary S
P P S
SLC-ssbuild1.cdr
Surge Suppressor

SLC Surge Suppression Installation
B.2 Installation
Mounting of the secondary surge suppressor must be inside the FACP enclosure or in a separate
enclosure listed for fire protective signaling use.
• Locate on an available stud and secure with nut.
• Unit is connected in series with the SLC Loop to protect the Control Panel.
• Provide a common ground to eliminate the possibility of a differential in ground potentials.
B.2.1 AFP-100 & AFP-200

DTK-2LVLP-F Connections
2LVLP-F
Optional Four-wire Return Loop

Style 6 (Class A)
IN OUT
SLC Terminal Block
2LVLP-F
–
+
SLC-lvlp1.cdr
SLC Loop
IN OUT
PLP-42N Connections
PLP-42N
GRND
L4
L4

OUTPUT
Style 6 (Class A)
L3
INPUT
L3
L2
L2
L1
L1
SLC Terminal Block

PLP-42N
–
GRND
L4
L4
+
OUTPUT
L3
INPUT
L3
L2
L2
SLC-plpn1.cdr
SLC Loop
L1
L1
NOTE: Use 12 AWG (3.31 mm2) to 18 AWG (0.82 mm2) wire with crimp-on connectors to
connect the unit’s ground terminal to equipment ground. Wire length must be minimized to
provide best protection.

Installation SLC Surge Suppression
SLCP-30 Connections
SLCP-30

Style 6 (Class A)
IN OUT
SLC Terminal Block
SLCP-30
SLC Loop
–
+
SLC-slcp1.cdr
IN OUT
B.2.2 AFP-300, AFP-400

2LVLP-F

Style 6 (Class A)
IN OUT
SLC Terminal Block

2LVLP-F
+
–
SLC-lvlp2.cdr
SLC Loop
IN OUT
PLP-42N Connections
PLP-42N
GRND
L4

L4
OUTPUT
Style 6 (Class A)
L3
INPUT
L3
L2
L2
L1
L1
PLP-42N SLC Terminal Block
+
GRND
L4
L4
–
OUTPUT
L3
INPUT
L3
L2
SLC-plpn2.cdr
L2
SLC Loop
L1
L1
provide best protection

SLC Surge Suppression Installation
SLCP-30 Connections
SLCP-30

Style 6 (Class A)
IN OUT
SLCP-30 SLC Terminal Block

SLC Loop
+
–
SLC-slcp2.cdr
IN OUT
B.2.3 AM2020 & AFP1010 (LIB-200A or LIB-400)

2LVLP-F
– SLC Terminal Block

+
SLC Loop
–
+
Optional Four-wire
SLC-lvlp3.cdr
Return Loop IN OUT
Style 6 (Class A)
NOTE: Do not connect shield (if present) to surge protector or fire panel.
PLP-42N Connections
PLP-42N
SLC Terminal Block

GRND
L4
L4
OUTPUT
L3
INPUT
L3
SLC Loop
L2
L2
L1
L1
SLC-plpn3.cdr
Optional Four-wire
Return Loop
Style 6 (Class A)
provide best protection. Do not connect shield (if present) to surge protector or fire panel.

Installation SLC Surge Suppression
SLCP-30 Connections
SLCP-30

+
SLC Loop –
+
SLC-slcp3.cdr
Optional Four-wire
Return Loop IN OUT
Style 6 (Class A)
B.2.4 NFS-640/E, NFS-3030/NFS2-3030

2LVLP-F

+
SLC Loop
–
+
Optional Four-wire
SLC-lvlp3.cdr
Return Loop IN OUT
Style 6 (Class A)
PLP-42N Connections
PLP-42N
SLC Terminal Block

GRND
L4
L4
OUTPUT
L3
INPUT
L3
SLC Loop
L2
L2
L1
L1
SLC-plpn3.cdr
Optional Four-wire
Return Loop
Style 6 (Class A)
provide best protection. Do not connect shield (if present) to surge protector or fire panel.
SLCP-30 Connections
SLCP-30

+
SLC Loop –
+
SLC-slcp3.cdr
Optional Four-wire
Return Loop IN OUT
Style 6 (Class A)

Notes

Index
Numerics detector bases
list of 13
24 VDC power 59–62
see also isolator bases
alternate method of supervising 62
detectors
monitoring and switching NAC power 45
24 VDC 60
listing 14
A devices
A77-716B addressable 31
Replaced by EOLR-1 auxiliary 13
See power supervision relay isolator 31
ACPS-2406 14, 59 maximum number between isolators 31
address capacity 31 SLC capacity 15
addressable devices 31 supervised 60
addressable modules 12, 37 dry contact ratings 51
AFC-600 Discontinued dry-contact 13
AFP-100 18, 21 DTK-2LVLP-F 65
AFP-200 18, 21 dual monitor module 38, 42
AFP-300/AFP-400 18, 22 duplicate addressing 42
AIM-200 18, 23
AM2020/AFP1010 17, 18, 22 E
AMPS-24/E 15, 59
analog intelligent devices 11 electrical interference 17
auxiliary devices 13 End-of-Line-Resistor 47, 62, 63
EOLR-1 See power supervision relay
B
F
B224BI, see isolator bases
FACP, see Fire Alarm Control Panels
B501 53
factory preset 39
B710HD 13, 53
FAPT-751 13
B710LP 53
FAPT-851 13
backup alarm, see degraded mode
fault 15, 33, 35
bases 13
fault condition 31
building entry/exit 65
Fault Isolator Module, see isolator module
FCM-1 45, 47, 48, 49, 60, 62, 63
C FCPS-24 59
cabinet 25 FDM-1, see dual monitor module
circuit fault 13 Fire Alarm Control Panels 9, 65
circuit, speaker/telephone 12 Fire alarm service 39, 41, 42, 43, 44
CLIP (Classic Loop Interface Protocol) 11, 16 FlashScan 11, 16, 32
coded output 62, 63 floating segments 27
common ground 66 FMM-1, see monitor module
communications loop 32 FMM-101, see miniature monitor module
conduit, types of 25–27 Form-C contacts 51
connector screw 25 four-wire configuration 48
connectors, crimp-on 66, 67, 68, 69 FSB-200, FSB-200S 13
control modules 12 FSI-751 14
CPX-551 14 FSI-851 14
CPX-751 14 FSL-751 14
FSP-751/T 14
D FSP-851/T 14
FST-751/R 14
DC resistance 19
FST-851/R 14
degraded mode 12, 37, 40, 41
FTM-1 12

G–P Index
FZM-1, see zone interface module control 12

isolator 13
G monitor 12, 37
relay 13
general alarm 62, 63 monitor module 37, 39, 41
ground terminal 66, 67, 68, 69
dual 42
group poll 11
dual see dual monitor module
grouped fashion 11 miniature, see miniature monitor module
zone interface see zone interface module
H monitor modules 12, 37
HARSH™ 54 MPS-24A 59
MPS-24B 59
MPS-400 59
I multiplex subsystem 13
IDC, see Initiating Device Circuits
Initiating Device Circuits 12, 37–44
integral relay 31 N
IPX-751 Discontinued December 1, 2001 NAC 12
isolator bases 13, 31, 32, 36 NAC power 45, 63
how they work 33 wiring 62
wiring 55 NAC terminal block 62
isolator devices 31 NBG-12LX 57
isolator modules 13, 35, 36 NEC Article 800 65
how they work 31 NFPA Style 4
wiring of 32 wiring 29
ISO-X, see isolator module NFPA Style 6
wiring 30
with isolator modules 35
J NFPA Style 7 31
junction box 26 with isolator device 36
NFPA Style B
K IDC wiring 39, 42, 43
key-lock reset 57 NFPA Style D
IDC wiring 41, 44
NFPA Style Y 45
L wiring 47
LCM-320/LEM-320 17, 21 NFPA Style Z 45
external power supervision 60 wiring 48
LED Annunciator, remote 53, 54 NFS2-3030/NFS-3030 21
LED operation 16 NFS-3030 17
LEM-320 NFS-640 17, 21
on NFS-3030, see LCM-320/LEM-320 normally closed contacts 60
on NFS-640 17, 21 Notification Appliance Circuit 12, 62
LIB-200 18 see also NAC
LIB-200A, LIB-400 17, 22 notification appliances 60
local building code 65
Loop Resistance 17, 18, 19
Style 6 & 7 20
P
loops 20 PLP-42N 65
LPX-751/L 14 Polling Protocols 11
power run 59, 60
power supervision relay 47, 48, 60
M power supplies 14, 59
metal conduit 26, 35 power-limited 62
Miniature monitor module 38 proper gauge wire 59
module circuits, configuring 37 pull stations 14, 36
modules addressable manual, wiring 57
addressable 12

Index R–Z
R V
RA400Z 53, 54 VIEW® 14
ratings, dry contact 51
relay bases 13, 31 W
relay module 13, 51
wiring 51 Waterflow alarm service, automatic and manual
39, 41, 42, 43, 44
Releasing Device
FCM-1 Connections 49 wire length
four-wire SLC 20
remote switching center 13
two-wire SLC 19
RFX Wireless Interface 14
wire nuts 26
rotary switches 39, 42, 43, 44
wire size 17, 18
wiring
S isolater bases 55
SDRF-751 14 isolator modules 32
Security service 39, 41, 42, 43, 44 NACs 62
shield 69 pull stations 57
shield drain wire 25 relay modules 51
shielded wire 26 SLCs 39, 41, 42, 43, 44
shield-termination 25 wiring pair 65
short circuit 31, 32 wiring style requirements 15
Signaling Line Circuit 11
see also SLC X
SLC
capacity of devices 15 XP Series Transponders 13
performance 15 XP5-C Transponder 12
setting an SLC address 39 XP5-M Transponder 12
terminal block 26
trouble conditions 15 Z
wiring 39, 41, 42, 43, 44 zone interface module 37, 43, 44
SLC-30 65
sounder bases 13, 31
speaker circuit 12
Sprinkler supervision 39, 41, 42, 43, 44
standard bases 13
Style 4, Style 6, Style 7, Style B,Style D, Style Y,
Style Z see NFPA Style 29
supervised circuits 60, 62
supervised devices 60
suppressors, surge 65
surge protector 11, 65
System 5000 with AIM-200 18, 23
T
telephone circuit 12
terminal block, NAC 63
termination of shield 25
transponders 13
trouble conditions 15, 31
trouble warning 33
T-tapping 19, 29, 30, 35, 36
twisted shielded pair wiring 17, 18
twisted unshielded pair wiring 17, 18
twisted-pair wire 26
two-wire configuration 47
two-wire detectors 60

Z–Z Index

Limited Warranty
NOTIFIER® warrants products manufactured by it to be free from

defects in materials and workmanship for eighteen (18) months from
the date of manufacture, under normal use and service. Products are
date stamped at time of manufacture. The sole and exclusive
obligation of NOTIFIER® is to repair or replace, at its option, free of
charge for parts and labor, any part that is defective in materials or
workmanship under normal use and service. All returns for credit are
subject to inspection and testing at the factory before actual
determination is made to allow credit. NOTIFIER® does not warrant
products not manufactured by it, but assigns to the purchaser any
warranty extended by the manufacturer of such products. This
warranty is void if the product is altered or repaired by anyone other
than NOTIFIER® or as expressly authorized by NOTIFIER® in
writing, or is serviced by anyone other than NOTIFIER® or its
authorized distributors. This warranty is also void if there is a failure to
maintain the products and systems in which they operate in a proper
and workable manner. In case of defect, secure a Return Material
Authorization form from our Return Authorization Department.
This writing constitutes the only warranty made by NOTIFIER®, with
respect to its products. NOTIFIER®, does not represent that its
products will prevent any loss by fire or otherwise, or that its products
will in all cases provide the protection for which they are installed or
intended. Buyer acknowledges that NOTIFIER®, is not an insurer
and assumes no risk for loss or damages or the cost of any
inconvenience, transportation damage, misuse, abuse, accident or
similar incident.
NOTIFIER® GIVES NO WARRANTY, EXPRESS OR IMPLIED, OF
MERCHANTABILITY, FITNESS FOR ANY PARTICULAR PURPOSE,
OR OTHERWISE WHICH EXTENDS BEYOND THE DESCRIPTION
ON THE FACE HEREOF. UNDER NO CIRCUMSTANCES SHALL
NOTIFIER® BE LIABLE FOR ANY LOSS OF OR DAMAGE TO
PROPERTY, DIRECT, INCIDENTAL OR CONSEQUENTIAL,
ARISING OUT OF THE USE OF, OR INABILITY TO USE
NOTIFIER®’S PRODUCTS. FURTHERMORE, NOTIFIER® SHALL
NOT BE LIABLE FOR ANY PERSONAL INJURY OR DEATH WHICH
MAY ARISE IN THE COURSE OF, OR AS A RESULT OF,
PERSONAL, COMMERCIAL OR INDUSTRIAL USE OF ITS
PRODUCTS.
This warranty replaces all previous warranties and is the only
warranty made by NOTIFIER®. No increase or alteration, written or
verbal, of the obligation of this warranty is authorized.
"NOTIFIER" is a registered trademark.
Warn-NL-04-2005.fm

World Headquarters NOTIFIER is a Honeywell company.
12 Clintonville Road
Northford, CT 06472-1653 USA
203-484-7161
fax 203-484-7118
www.notifier.com

SLC Signaling Line Circuit

Uploaded by

Copyright:

Available Formats

SLC Signaling Line Circuit

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

SLC Signaling Line Circuit

Uploaded by

Copyright:

Available Formats

Intelligent Control Panel

2 The SLC Wiring Manual — P/N 51253:G 11/29/2005

The SLC Wiring Manual — P/N 51253:G 11/29/2005 3

Please include the following information:

Send email messages to:

4 The SLC Wiring Manual — P/N 51253:G 11/29/2005

The SLC Wiring Manual — P/N 51253:G 11/29/2005 5

5.2.1: Wiring an Isolator Module.................................................................................................................32

6 The SLC Wiring Manual — P/N 51253:G 11/29/2005

DTK-2LVLP-F Connections ...............................................................................................................67

The SLC Wiring Manual — P/N 51253:G 11/29/2005 7

8 The SLC Wiring Manual — P/N 51253:G 11/29/2005

1.1 About This Manual

1.2 UL 864 Compliance

The SLC Wiring Manual — P/N 51253:G 11/29/2005 9

1.3 Reference Documentation

10 The SLC Wiring Manual — P/N 51253:G 11/29/2005

FMM-1 Monitor Module Installation Document I56-1171

1.4 SLC Overview

1.5 Polling Protocols

The SLC Wiring Manual — P/N 51253:G 11/29/2005 11

2. Program all modules and detectors on an SLC as CLIP.

3. Program all detectors as CLIP and all modules as FlashScan on an SLC.

1.6.2 Control Modules

12 The SLC Wiring Manual — P/N 51253:G 11/29/2005

1.6.3 Isolator Modules

1.6.4 Relay Modules

1.6.6 Plug-in Detector Bases

1.6.7 Intelligent Detectors

The SLC Wiring Manual — P/N 51253:G 11/29/2005 13

1.6.8 Addressable Manual Pull Stations

1.6.9 RFX Wireless Interface

1.6.10 ACPS-2406 Addressable Charger/Power Supply

14 The SLC Wiring Manual — P/N 51253:G 11/29/2005

1.6.11 AMPS-24/E Addressable Power Supply

1.7 SLC Capacity

1.8 SLC Performance

Type of Fault Style 4 Style 6 Style 7

Single Open Trouble Alarm, Trouble Alarm, Trouble

The SLC Wiring Manual — P/N 51253:G 11/29/2005 15

1.9 LED Operation

CLIP Mode FlashScan® Mode

Control Panel Device Standby Activated Standby Activated

AM2020 Monitor Module Blinks RED RED continuous N/A N/A

AFP-300/AFP-400 Monitor Module Blinks RED RED continuous N/A N/A

AFP-100 Monitor Module Blinks RED RED continuous N/A N/A

AFP-200 Monitor Module Blinks RED RED continuous N/A N/A

16 The SLC Wiring Manual — P/N 51253:G 11/29/2005

2.1 Recommended SLC Wiring

LIB-200A or LIB-400 on AM2020/AFP1010 (See Table 2.2 for LIB-200.)

Twisted unshielded pair, 12 to 18 AWG 12,500 ft. (3,810 m) 12 AWG/3.31 mm²

NFS-640 and LEM-320 on NFS-640

Twisted-unshielded pair, 12 to 18 AWG 12,500 ft. (3,810 m) 12 AWG (3.31 mm²)

LCM-320, LEM-320 on NFS-3030 or NFS2-3030

Twisted-unshielded pair, 12 to 18 AWG 12,500 ft. (3,810 m) 12 AWG (3.31 mm²)

Table 2.1 Wiring Recommendations: NFS-640, NFS-3030/NFS2-3030, LCM-320, LEM-320, LIB-200A,

The SLC Wiring Manual — P/N 51253:G 11/29/2005 17

Twisted-shielded pair. 40 ohms 10,000 ft. (3,048 m) 12 AWG (3.31 mm²)

Twisted-shielded pair, 12 to 18 AWG. 10,000 ft. (3,048 m) 12 AWG (3.31 mm²)

LIB-200 on AM2020/AFP1010 (See Table 2.1 for LIB-200A or LIB-400.)