PDS Foster 30 45 Foamseal Sealant

®
30-45
Product Data Sheet
PROPERTIES FOSTER® FOAMSEAL™ SEALANT

®
COLOUR: Grey FOSTER FOAMSEAL™ Sealant is a grey vapor barrier
sealant designed for use with rigid thermal insulation including
APPLICATION CONSISTENCY: polystyrene foam. It remains flexible and tough in joints and will
Trowel, or power extrusion not shrink or crack during repeated cycles of high and low
temperatures.
SPECIFIC GRAVITY:
®
1.44kg/l FOSTER FOAMSEAL™ Sealant seals the joints of cellular
glass and other insulations against the entrance of moisture.
AVERAGE SOLIDS: When used as a bedding compound on iron or steel surfaces
99% by weight and as a joint sealant, 30-45 provides additional protection to
the blocks of insulation. Damage to the insulation due to
COVERAGE RANGE: migration of moisture is minimized.
2
Trowel: 1.6 – 3.5l/m
®
At 1.6 – 3.2mm wet film thickness FOSTER FOAMSEAL™ Sealant is water and weather
resistant and is often used as a sealant and flashing compound
DRYING TIME 23ºC / 50% RH: where structural parts must penetrate an insulation surface.
To Touch: 24 hours
®
Full Set: 7 days FOSTER FOAMSEAL™ Sealant contains no asbestos, lead,
mercury, or mercury compounds.
SERVICE TEMPERATURE LIMITS:
-73ºC to 149ºC LIMITATIONS
Store between 4ºC and 38ºC.
WATER VAPOR PERMEANCE (ASTM E 96):
0.013 metric perm-cm (0.008 perm-inch). Apply between 10ºC and 43ºC.
The water vapor transmission through 25mm of
impermeable insulation in 30 X 45cm blocks with Allow to cure one week before placing in heated service.
6.4mm joints of 30-45 is too small to measure.
Application of Foster® Foamseal™ Sealant to all pipe work must
WET FLAMMABILITY: fully comply with all application guidelines and
No flash to boiling, 93ºC recommendations, in particular, Specification No. 2.1 and2.1:
Cold Work Insulation, which can be found at
COMBUSTIBILITY: www.hbfuller.com.au or by contacting HB Fuller at 16-22 Red
Combustible. Flame spread and fuel contribution Gum Drive, Dandenong South, Vic 3175, or telephone 1800-
negligible when used as sealant in 3.2mm wide joints 423-855. Not suggested for use with copper, aluminium or
of incombustible insulation. plastic pipe work.
Foster and Foamseal are the trademarks of Specialty Not suggested for use under solvent base elastomeric mastics
Construction Brands, Inc. and coatings, if minor surface discoloration and/or dirt pick-up
would be objectionable. Discoloration can be minimized by
®
Visit us on the Foster US website at allowing 24 to 48 hours cure time before top coating.
www.fosterproducts.com
Make certain this product is completely dry and the area free
from product odour if food is involved.
01/’09
H.B. Fuller Australia Pty Ltd

16-22 Red Gum Drive ○ Dandenong South ○ Vic 3175 Australia ○ Ph: 1800-423-855 ○ Fax: 1800-420-055
APPLICATION GUIDE
FOSTER® FOAMSEAL™ SEALANT
30-45
MATERIAL PREPARATION
DO NOT THIN. Apply only to clean, dry surfaces. Keep container closed when not in use.
APPLICATION
®
Apply by trowel, putty knife, power extrusion or bulk caulking gun. When sealing insulation joints apply FOSTER FOAMSEAL™
Sealant at 1.6 to 3.2mm wet film thickness and press mating surfaces together firmly to squeeze out air bubbles and to obtain
complete contact. When flashing, do not trowel out to feather edge, but maintain a minimum of 3.2mm wet film thickness throughout
the entire area of use. Use membrane as specified. For best results, allow to cure 24-48 hours before top coating with solvent-based
elastomeric mastics or coatings.
POWER EXTRUSION
®
FOSTER FOAMSEAL™ Sealant may be applied using a wide variety of power (pressure) extrusion equipment suitable for use with
oil base sealants. Typical viscosity range: 0.5 - 1.0 million cps.
CLEAN-UP
Clean tools and equipment with mineral spirits (flammable) or chlorinated solvent (non-flammable).
CUSTOMER SERVICE — 1800 423 855

IMPORTANT: H.B. Fuller Australia Pty Ltd warrants that each of its products will be manufactured in accordance with the specifications in effect on the date of manufacture.
WE MAKE NO OTHER WARRANTIES AND EXPRESSLY DISCLAIM ANY WARRANTIES OF MERCHANTIBILITY OR FITNESS FOR A PARTICULAR PURPOSE. If a
product fails to meet this limited warranty, purchaser’s sole and exclusive remedy is replacement of the product or, at our option, refund of the purchase price. OUR
ACCEPTANCE OF ANY ORDERS FOR THE PRODUCT IS EXPRESSLY CONDITIONAL UPON PURCHASER’S ASSENT TO THE TERMS ON THE APPLICABLE
INVOICE.
ADEQUATE TESTS: The information contained herein we believe is correct to the best of our knowledge and tests. The recommendations and suggestions herein are
made without guarantee or representation as to results. We recommend that adequate tests be performed by you to determine if this product meets all of your
requirements. The warranted shelf life of our products is six months from date of shipment to the original purchaser.
For industrial use only. Keep out of reach of children.

Consult Material Safety Data Sheet and container label for further information.
DSF30-45
®
16-22 Red Gum Drive Dandenong South, Vic 3175 Australia Ph: 1800-423-855 Fax: 1800-420-055 www.fosterproducts.com
Specification No. 2.1: Cold Work insulation

Vessel Temperature: -20°C to 15°C
Insulation used: Polystyrene, Glass wool, Polyester
Application: Internal/external light duty
Examples: Chilled water piping; coolant/refrigerant lines
Finish coat of 30-90
Tack coat of 30-90
Insulation
252WB Adhesive
Embedded No.10
Glass Cloth Steel Piping
30-45 Foamseal
Process fluid
1. Ensure pipe surface is clean, dry and free of rust, grease, and oil.
2. Apply Foster® Foamseal™ 30-45 to steel pipework at a coverage rate of 2.5 lt/m2. Do not thin.
3. Attach pipe sections using Foster® 252WB™ applied to all surfaces at a rate of 0.5 lt/m2, including
longitudinal and butt joints between sections. Press insulation into pipe and other sections to
remove air bubbles and ensure the absence of gaps.
4. Flash insulation sections using Foster® Foamseal™ 30-45 at a wet film thickness of 3.2mm.
5. Apply a tack coat of Foster® Vapour-Safe™ 30-90 to entire external surface of insulation at a
coverage rate of 0.8 lt/m2 (wet film thickness of 0.8mm).
6. Embed No.10 glass cloth into wet coating, overlapping all seams by 50mm. Smooth out all
wrinkles.
7. Within ½ hour after tack coat application, apply a finish coat of Foster® Vapour-Safe™ 30-90 at a coverage
2
rate of 0.8 lt/m (wet film thickness of 0.8mm).
® ™
Note: Foster Foamseal 30-45 sealant is not suggested for direct contact with copper, aluminium or plastic piping.
®
16-22 Red Gum Drive Dandenong South, Vic 3175 Australia Ph: 1800-423-855 Fax: 1800-420-055 www.fosterproducts.com
Specification No. 2.2: Cold Work insulation

Vessel Temperature: -73°C to 15°C
Insulation used: Polyurethane
Application: Internal/external light duty
Examples: Refrigerant lines, freezers
Finish coat of 30-90
Tack coat of 30-90
Insulation
30-45 sealant
Embedded No.10
Glass Cloth Steel Piping
Process fluid
1. Ensure pipe surface is clean, dry and free of rust, grease, and oil.
2. Seal all joints between insulation sections using Foster® Foamseal™ 30-45. Flash
insulation sections using Foster® Foamseal™ 30-45 at a wet film thickness of 3.2mm.
3. Apply a tack coat of Foster® Vapour-Safe™ 30-90 to entire external surface of insulation
at a coverage rate of 0.8 lt/m2 (wet film thickness of 0.8mm).
4. Embed No.10 glass cloth into wet coating, overlapping all seams by 50mm. Smooth out
all wrinkles.
5. Within ½ hour after tack coat application, apply a finish coat of Foster® Vapour-Safe™ at a
coverage rate of 1.6 lt/m2 (wet film thickness of 1.6mm).
® ™
Note: Foster Foamseal 30-45 sealant is not suggested for direct contact with copper, aluminium or plastic piping.

PDS Foster 30 45 Foamseal Sealant

Uploaded by

Copyright:

Available Formats

PDS Foster 30 45 Foamseal Sealant

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

PDS Foster 30 45 Foamseal Sealant

Uploaded by

Copyright:

Available Formats

®

PROPERTIES FOSTER® FOAMSEAL™ SEALANT

H.B. Fuller Australia Pty Ltd

CUSTOMER SERVICE — 1800 423 855

For industrial use only. Keep out of reach of children.

Specification No. 2.1: Cold Work insulation

Finish coat of 30-90

Tack coat of 30-90

Specification No. 2.2: Cold Work insulation

Finish coat of 30-90

Tack coat of 30-90

You might also like