This document provides product data for the Endos ACP Intra-oral X-ray unit, including specifications for the tubehead, scissors and extension arm, timer features, electrical characteristics, environmental conditions, certifications, and keyboard functions. The tubehead has a high voltage circuit of 70 kVp ± 6% and 8 mA current. The timer allows for exposure times from 0.02 to 3.2 seconds in 33 steps. The unit is designed to meet European, US, and Canadian medical device standards.
This document provides product data for the Endos ACP Intra-oral X-ray unit, including specifications for the tubehead, scissors and extension arm, timer features, electrical characteristics, environmental conditions, certifications, and keyboard functions. The tubehead has a high voltage circuit of 70 kVp ± 6% and 8 mA current. The timer allows for exposure times from 0.02 to 3.2 seconds in 33 steps. The unit is designed to meet European, US, and Canadian medical device standards.
This document provides product data for the Endos ACP Intra-oral X-ray unit, including specifications for the tubehead, scissors and extension arm, timer features, electrical characteristics, environmental conditions, certifications, and keyboard functions. The tubehead has a high voltage circuit of 70 kVp ± 6% and 8 mA current. The timer allows for exposure times from 0.02 to 3.2 seconds in 33 steps. The unit is designed to meet European, US, and Canadian medical device standards.
This document provides product data for the Endos ACP Intra-oral X-ray unit, including specifications for the tubehead, scissors and extension arm, timer features, electrical characteristics, environmental conditions, certifications, and keyboard functions. The tubehead has a high voltage circuit of 70 kVp ± 6% and 8 mA current. The timer allows for exposure times from 0.02 to 3.2 seconds in 33 steps. The unit is designed to meet European, US, and Canadian medical device standards.
Tubehead Features High voltage circuit type Single phase, self-rectifying, grid controlled Rated output voltage 70 kVp ± 6% @ 230V 70 kVp ± 6% @ 120V Tubehead current 8 mA Tubehead power 430 VA Total filtration 2 mm Al eq. @ 70 kV Maximum deviation of output cur- ± 13% rent Pre-heating time 100 ms Interval between exposures 1:32 (duty cycle) Minimum focus to skin distance 20 cm 30 cm with optional collimator cone X-ray field (at collimator tip) Circular, diameter 6 cm Rectangular 35x45 mm with optional diaphragm Leakage radiation @ 1m ≤ 0.1 mGy/h Technical factors for leakage radia- 70 kV, 8 mA, 1 s, 1:32 duty cycle tion Tube insert type OCX/70-G Focal spot 0.8 (IEC 336) Anode material Tungsten Anode angle 19° Inherent filtration 0.5 mm Al eq. @ 70 kV Anode thermal capacity 6 kJ
Scissors and Extension Arm Features
Material Aluminum Type of painting Glossy Mounting type - Wall mount with local timer - Wall mount with remote timer - Wall mount with remote X-ray pushbutton - Ceiling mount - Mobile unit on trolley Choice of extension arm length - 30 cm (only for wall mounted units) - 60 cm - 80 cm
Product data Endos ACP – Rev.5 Page 1 of 5
Timer Features Exposure times From 0.02 to 3.2s in 33 steps Exposure times control Microprocessor controlled exposure times, with automatic compensation of line voltage fluctuations Timer accuracy ±10% or ±20 ms (whatever is greater) @ 230V ±10% or ±32.2 ms (whatever is greater) @ 120V Exposure times visualization Digital display Exposure button With extensible cable (3m) Stand-by function The system enters a low-consumption state after 5 minutes of inactivity Number of anatomic programs 30 pre-set times Choice of patient size 3 choices (small, medium, large) Choice of anatomic region - Incisors/canines (upper an lower) - Premolars (upper an lower) - Upper molars - Lower molars - Bite wing Automatic dose reduction for Yes, with pushbutton on keyboard videoradiography systems Film speed setting Yes CCD/ phosphor-plates setting Yes Visualization of number of expo- Yes sures External connections Provisions for connection of: - Remote x-ray pushbutton - Unit powered signal lamp - X-ray active signal lamp
Electrical Characteristics Line voltage 230V ± 10% 120V ± 10% Line frequency 50 Hz 60 Hz Absorbed current 4A rms @ 230V 8A rms @ 120V Absorbed power 920 VA @ 230V 1.1 kVA @ 120V Line resistance ≤ 0.8 Ohm N/A Max line voltage regulation N/A 3% @ 132V
Environmental Conditions Operating conditions Temperature: +10° to +40° Celsius Humidity: 30% to 75% Conditions for transport and Temperature: -20° to +70° Celsius storage Humidity: up to 95 % non condensing Pressure: up to 630 hPa
Product data Endos ACP – Rev.5 Page 2 of 5
Standard and Regulations This product is designed and produced to meet the following standards: EN 60601-1, EN 60601-1-1, EN 60601-1-2, EN 60601-1-3, EN 60601-1-4, EN 60601-2-7, EN 60601-2-28, EN 60601-2-32, EN 1441 CE symbol grants the product compliance to the European Directive for Medical Devices 93/42/EEC and its revised 0051 versions as a class IIB device c-ETL-us approval means that the product meets the requirements of the applicable US and Canadian standards (Only for 120V version)
FDA approval grants the product compliance to US Code of
Federal Regulations title 21 subchapter j (Only for 120V version) Health Canada Licence grants the product compliance to the Canadian Medical Device Regulations SOR/98-282 (Only for 120V version)
Keyboard Functions
1. Ready for exposure signal lamp 10. Premolars (upper and lower) signal lamp 2. Manual decrease of exposure times 11. Incisors/canines (upper and lower) 3. Manual increase of exposure times signal lamp 4. X-ray emission warning lamp 12. Anatomic selection 5. Video radiography signal lamp 13. Large patient size signal lamp 6. Video radiography selection 14. Medium patient size signal lamp 7. Bite wing signal lamp 15. Small patient size signal lamp 8. Upper molars signal lamp 16. Patient size selection 9. Lower molars signal lamp 17. Exposure enable button
Product data Endos ACP – Rev.5 Page 3 of 5
Site Planning (quotes in mm and inches) WALL MOUNT 120 (4-3/4") FRONTAL VIEW
Note: Products are continuously under review in the light of technical advancement. The actual specification may therefore be subject to improvement or modification without notice.
Company with Quality System certified by
VILLA SISTEMI MEDICALI s.p.a. 20090 BUCCINASCO (MI) – ITALY, Via delle Azalee, 3 Tel. +39-02-48859.1, Fax +39-02-4881844
