Appendix B – Limits and Fits | B - 1

Appendix B
Limits and Fits
ANSI/ASME B4.1-1967 (R2004) Standard

1. Limits and Fits (Inches)

1.1 Running and Sliding Clearance Fits (RC)

Basic hole system. Limit dimensions are in thousandths of an inch.

Nominal Size Class RC1 Class RC2 Class RC3 Class RC4
Range Inches Standard Limits Standard Limits Standard Limits Standard Limits
Over To Hole Shaft Hole Shaft Hole Shaft Hole Shaft
0.2 -0.1 0.25 -0.1 0.4 -0.3 0.6 -0.3
0 ~ 0.12
0 -0.25 0 -0.3 0 -0.55 0 -0.7
0.2 -0.15 0.3 -0.15 0.5 -0.4 0.7 -0.4
0.12 ~ 0.24
0 -0.3 0 -0.35 0 -0.7 0 -0.9
0.25 -0.2 0.4 -0.2 0.6 -0.5 0.9 -0.5
0.24 ~ 0.40
0 -0.35 0 -0.45 0 -0.9 0 -1.1
0.3 -0.25 0.4 -0.25 0.7 -0.6 1.0 -0.6
0.40 ~ 0.71
0 -0.45 0 -0.55 0 -1.0 0 -1.3
0.4 -0.3 0.5 -0.3 0.8 -0.8 1.2 -0.8
0.71 ~ 1.19
0 -0.55 0 -0.7 0 -1.3 0 -1.6
0.4 -0.4 0.6 -0.4 1.0 -1.0 1.6 -1.0
1.19 ~ 1.97
0 -0.7 0 -0.8 0 -1.6 0 -2.0
0.5 -0.4 0.7 -0.4 1.2 -1.2 1.8 -1.2
1.97 ~ 3.15
0 -0.7 0 -0.9 0 -1.9 0 -2.4
0.6 -0.5 0.9 -0.5 1.4 -1.4 2.2 -1.4
3.15 ~ 4.73
0 -0.9 0 -1.1 0 -2.3 0 -2.8
0.7 -0.6 1.0 -0.6 1.6 -1.6 2.5 -1.6
4.73 ~ 7.09
0 -1.1 0 -1.3 0 -2.6 0 -3.2
0.8 -0.6 1.2 -0.6 1.8 -2.0 2.8 -2.0
7.09 ~ 9.85
0 -1.2 0 -1.4 0 -3.2 0 -3.8
0.9 -0.8 1.2 -0.7 2.0 -2.5 3.0 -2.2
9.85 ~ 12.41
0 -1.4 0 -1.6 0 -3.7 0 -4.2
1.0 -1.0 1.4 -0.7 2.2 -3.0 3.5 -2.5
12.41 ~ 15.75
0 -1.7 0 -1.7 0 -4.4 0 -4.7
1.0 -1.2 1.6 -0.8 2.5 -4.0 4.0 -2.8
15.75 ~ 19.69
0 -2.0 0 -1.8 0 -5.6 0 -5.3
B - 2 | Appendix B – Limits and Fits

(Cont. - 1.1 Running and Sliding Clearance Fits (RC))

Basic hole system. Limit dimensions are in thousandths of an inch.

Nominal Size Class RC5 Class RC6 Class RC7 Class RC8 Class RC9
Range Inches Standard Limits Standard Limits Standard Limits Standard Limits Standard Limits
Over To Hole Shaft Hole Shaft Hole Shaft Hole Shaft Hole Shaft

0 ~ 0.12
0.6 -0.6 1.0 -0.6 1.0 -1.0 1.6 -2.5 2.5 -4.0
0 -1.0 0 -1.2 0 -1.6 0 -3.5 0 -5.6
0.12 ~ 0.24
0.7 -0.8 1.2 -0.8 1.2 -1.2 1.8 -2.8 3.0 -4.5
0 -1.3 0 -1.5 0 -1.9 0 -4.0 0 -6.0
0.9 -1.0 1.4 -1.0 1.4 -1.6 2.2 -3.0 3.5 -5.0
0.24 ~ 0.40
0 -1.6 0 -1.9 0 -2.5 0 -4.4 0 -7.2
0.40 ~ 0.71
1.0 -1.2 1.6 -1.2 1.6 -2.0 2.8 -3.5 4.0 -6.0
0 -1.9 0 -2.2 0 -3.0 0 -5.1 0 -8.8
0.71 ~ 1.19
1.2 -1.6 2.0 -1.6 2.0 -2.5 3.5 -4.5 5.0 -7.0
0 -2.4 0 -2.8 0 -3.7 0 -6.5 0 -10.5
1.19 ~ 1.97
1.6 -2.0 2.5 -2.0 2.5 -3.0 4.0 -5.0 6.0 -8.0
0 -3.0 0 -3.6 0 -4.6 0 -7.5 0 -12.0
1.97 ~ 3.15
1.8 -2.5 3.0 -2.5 3.0 -4.0 4.5 -6.0 7.0 -9.0
0 -3.7 0 -4.3 0 -5.8 0 -9.0 0 -13.5
3.15 ~ 4.73
2.2 -3.0 3.5 -3.0 3.5 -5.0 5.0 -7.0 9.0 -10.0
0 -4.4 0 -5.2 0 -7.2 0 -10.5 0 -15.0
4.73 ~ 7.09
2.5 -3.5 4.0 -3.5 4.0 -6.0 6.0 -8.0 10.0 -12.0
0 -5.1 0 -6.0 0 -8.5 0 -12.0 0 -18.0
7.09 ~ 9.85
2.8 -4.0 4.5 -4.0 4.5 -7.0 7.0 -10.0 12.0 -15.0
0 -5.8 0 -6.8 0 -9.8 0 -14.5 0 -22.0
9.85 ~ 12.41
3.0 -5.0 5.0 -5.0 5.0 -8.0 8.0 -12.0 12.0 -18.0
0 -7.0 0 -8.0 0 -11.0 0 -17.0 0 -26.0
12.41 ~ 15.75
3.5 -6.0 6.0 -6.0 6.0 -10.0 9.0 -14.0 14.0 -22.0
0 -8.2 0 -9.5 0 -13.5 0 -20.0 0 -31.0
15.75 ~ 19.69
4.0 -8.0 6.0 -8.0 6.0 -12.0 10.0 -16.0 16.0 -25.0
0 -10.5 0 -12.0 0 -16.0 0 -22.0 0 -35.0
 Appendix B – Limits and Fits | B - 3

1.2 Locational Clearance Fits (LC)

Basic hole system. Limit dimensions are in thousandths of an inch.

Nominal Size Class LC1 Class LC2 Class LC3 Class LC4
Range Inches Standard Limits Standard Limits Standard Limits Standard Limits
Over To Hole Shaft Hole Shaft Hole Shaft Hole Shaft
0.25 0 0.4 0 0.6 0 1.6 0
0 ~ 0.12
0 -0.2 0 -0.25 0 -0.4 0 -1.0
0.3 0 0.5 0 0.7 0 1.8 0
0.12 ~ 0.24
0 -0.2 0 -0.3 0 -0.5 0 -1.2
0.4 0 0.6 0 0.9 0 2.2 0
0.24 ~ 0.40
0 -0.25 0 -0.4 0 -0.6 0 -1.4
0.4 0 0.7 0 1.0 0 2.8 0
0.40 ~ 0.71
0 -0.3 0 -0.4 0 -0.7 0 -1.6
0.5 0 0.8 0 1.2 0 3.5 0
0.71 ~ 1.19
0 -0.4 0 -0.5 0 -0.8 0 -2.0
0.6 0 1.0 0 1.6 0 4.0 0
1.19 ~ 1.97
0 -0.4 0 -0.6 0 -1.0 0 -2.5
0.7 0 1.2 0 1.8 0 4.5 0
1.97 ~ 3.15
0 -0.5 0 -0.7 0 -1.2 0 -3.0
0.9 0 1.4 0 2.2 0 5.0 0
3.15 ~ 4.73
0 -0.6 0 -0.9 0 -1.4 0 -3.5
1.0 0 1.6 0 2.5 0 6.0 0
4.73 ~ 7.09
0 -0.7 0 -1.0 0 -1.6 0 -4.0
1.2 0 1.8 0 2.8 0 7.0 0
7.09 ~ 9.85
0 -0.8 0 -1.2 0 -1.8 0 -4.5
1.2 0 2.0 0 3.0 0 8.0 0
9.85 ~ 12.41
0 -0.9 0 -1.2 0 -2.0 0 -5.0
1.4 0 2.2 0 3.5 0 9.0 0
12.41 ~ 15.75
0 -1.0 0 -1.4 0 -2.2 0 -6.0
1.6 0 2.5 0 4.0 0 10.0 0
15.75 ~ 19.69
0 -1.0 0 -1.6 0 -2.5 0 -6.0
B - 4 | Appendix B – Limits and Fits

(Cont. - 1.2 Locational Clearance Fits (LC))

Basic hole system. Limit dimensions are in thousandths of an inch.

Nominal Size Class LC5 Class LC6 Class LC7 Class LC8
Range Inches Standard Limits Standard Limits Standard Limits Standard Limits
Over To Hole Shaft Hole Shaft Hole Shaft Hole Shaft
0.40 -0.1 1.0 -0.3 1.6 -0.6 1.6 -1.0
0 ~ 0.12
0 -0.35 0 -0.9 0 -1.6 0 -2.0
0.5 -0.15 1.2 -0.4 1.8 -0.8 1.8 -1.2
0.12 ~ 0.24
0 -0.45 0 -1.1 0 -2.0 0 -2.4
0.6 -0.2 1.4 -0.5 2.2 -1.0 2.2 -1.6
0.24 ~ 0.40
0 -0.6 0 -1.4 0 -2.4 0 -3.0
0.7 -0.25 1.6 -0.6 2.8 -1.2 2.8 -2.0
0.40 ~ 0.71
0 -0.65 0 -1.6 0 -2.8 0 -3.6
0.8 -0.3 2.0 -0.8 3.5 -1.6 3.5 -2.5
0.71 ~ 1.19
0 -0.8 0 -2.0 0 -3.6 0 -4.5
1.0 -0.4 2.5 -1.0 4.0 -2.0 4.0 -3.0
1.19 ~ 1.97
0 -1.0 0 -2.6 0 -4.5 0 -5.5
1.2 -0.4 3.0 -1.2 4.5 -2.5 4.5 -4.0
1.97 ~ 3.15
0 -1.1 0 -3.0 0 -5.5 0 -7.0
1.4 -0.5 3.5 -1.4 5.0 -3.0 5.0 -5.0
3.15 ~ 4.73
0 -1.4 0 -3.6 0 -6.5 0 -8.5
1.6 -0.6 4.0 -1.6 6.0 -3.5 6.0 -6.0
4.73 ~ 7.09
0 -1.6 0 -4.1 0 -7.5 0 -10.0
1.8 -0.6 4.5 -2.0 7.0 -4.0 7.0 -7.0
7.09 ~ 9.85
0 -1.8 0 -4.8 0 -8.5 0 -11.5
2.0 -0.7 5.0 -2.2 8.0 -4.5 8.0 -7.0
9.85 ~ 12.41
0 -1.9 0 -5.2 0 -9.5 0 -12.0
2.2 -0.7 6.0 -2.5 9.0 -5.0 9.0 -8.0
12.41 ~ 15.75
0 -2.1 0 -6.0 0 -11.0 0 -14.0
2.5 -0.8 6.0 -2.8 10.0 -5.0 10.0 -9.0
15.75 ~ 19.69
0 -2.4 0 -6.8 0 -11.0 0 -15.0
 Appendix B – Limits and Fits | B - 5

(Cont. - 1.2 Locational Clearance Fits (LC))

Basic hole system. Limit dimensions are in thousandths of an inch.

Nominal Size Class LC9 Class LC10 Class LC11

Range Inches Standard Limits Standard Limits Standard Limits
Over To Hole Shaft Hole Shaft Hole Shaft
2.5 -2.5 4.0 -4.0 6.0 -5.0
0 ~ 0.12
0 -4.1 0 -8.0 0 -11.0
3.0 -2.8 5.0 -4.5 7.0 -6.0
0.12 ~ 0.24
0 -4.6 0 -9.5 0 -13.0
3.5 -3.0 6.0 -5.0 9.0 -7.0
0.24 ~ 0.40
0 -5.2 0 -11.0 0 -16.0
4.0 -3.5 7.0 -6.0 10.0 -8.0
0.40 ~ 0.71
0 -6.3 0 -13.0 0 -18.0
5.0 -4.5 8.0 -7.0 12.0 -10.0
0.71 ~ 1.19
0 -8.0 0 -15.0 0 -22.0
6.0 -5.0 10.0 -8.0 16.0 -12.0
1.19 ~ 1.97
0 -9.0 0 -18.0 0 -28.0
7.0 -6.0 12.0 -10.0 18.0 -14.0
1.97 ~ 3.15
0 -10.5 0 -22.0 0 -32.0
9.0 -7.0 14.0 -11.0 22.0 -16.0
3.15 ~ 4.73
0 -12.0 0 -25.0 0 -38.0
10.0 -8.0 16.0 -12.0 25.0 -18.0
4.73 ~ 7.09
0 -14.0 0 -28.0 0 -43.0
12.0 -10.0 18.0 -16.0 28.0 -22.0
7.09 ~ 9.85
0 -17.0 0 -34.0 0 -50.0
12.0 -12.0 20.0 -20.0 30.0 -28.0
9.85 ~ 12.41
0 -20.0 0 -40.0 0 -58.0
14.0 -14.0 22.0 -22.0 35.0 -30.0
12.41 ~ 15.75
0 -23.0 0 -44.0 0 -65.0
16.0 -16.0 25.0 -25.0 40.0 -35.0
15.75 ~ 19.69
0 -26.0 0 -50.0 0 -75.0
B - 6 | Appendix B – Limits and Fits

1.3 Locational Transition Fits (LT)

Basic hole system. Limit dimensions are in thousandths of an inch.

Nominal Size Class LT1 Class LT2 Class LT3

Range Inches Standard Limits Standard Limits Standard Limits
Over To Hole Shaft Hole Shaft Hole Shaft
0.4 0.1 0.6 0.2
0 ~ 0.12
0 -0.10 0 -0.2
0.5 0.15 0.7 0.25
0.12 ~ 0.24
0 -0.15 0 -0.25
0.6 0.2 0.9 0.3 0.6 0.5
0.24 ~ 0.40
0 -0.2 0 -0.3 0 0.1
0.7 0.2 1.0 0.35 0.7 0.5
0.40 ~ 0.71
0 -0.2 0 -0.35 0 0.1
0.8 0.25 1.2 0.4 0.8 0.6
0.71 ~ 1.19
0 -0.25 0 -0.4 0 0.1
1.0 0.3 1.6 0.5 1.0 0.7
1.19 ~ 1.97
0 -0.3 0 -0.5 0 0.1
1.2 0.3 1.8 0.6 1.2 0.8
1.97 ~ 3.15
0 -0.3 0 -0.6 0 0.1
1.4 0.4 2.2 0.7 1.4 1.0
3.15 ~ 4.73
0 -0.4 0 -0.7 0 0.1
1.6 0.5 2.5 0.8 1.6 1.1
4.73 ~ 7.09
0 -0.5 0 -0.8 0 0.1
1.8 0.6 2.8 0.9 1.8 1.4
7.09 ~ 9.85
0 -0.6 0 -0.9 0 0.2
2.0 0.6 3.0 1.0 2.0 1.4
9.85 ~ 12.41
0 -0.6 0 -1.0 0 0.2
2.2 0.7 3.5 1.0 2.2 1.6
12.41 ~ 15.75
0 -0.7 0 -1.0 0 0.2
 Appendix B – Limits and Fits | B - 7

(Cont. - 1.3 Locational Transition Fits (LT))

Basic hole system. Limit dimensions are in thousandths of an inch.

Nominal Size Class LT4 Class LT5 Class LT6

Range Inches Standard Limits Standard Limits Standard Limits
Over To Hole Shaft Hole Shaft Hole Shaft
0.4 0.5 0.4 0.65
0 ~ 0.12
0 0.25 0 0.25
0.5 0.6 0.5 0.8
0.12 ~ 0.24
0 0.3 0 0.3
0.9 0.7 0.6 0.8 0.6 1.0
0.24 ~ 0.40
0 0.1 0 0.4 0 0.4
1.0 0.8 0.7 0.9 0.7 1.2
0.40 ~ 0.71
0 0.1 0 0.5 0 0.5
1.2 0.9 0.8 1.1 0.8 1.4
0.71 ~ 1.19
0 0.1 0 0.6 0 0.6
1.6 1.1 1.0 1.3 1.0 1.7
1.19 ~ 1.97
0 0.1 0 0.7 0 0.7
1.8 1.3 1.2 1.5 1.2 2.0
1.97 ~ 3.15
0 0.1 0 0.8 0 0.8
2.2 1.5 1.4 1.9 1.4 2.4
3.15 ~ 4.73
0 0.1 0 1.0 0 1.0
2.5 1.7 1.6 2.2 1.6 2.8
4.73 ~ 7.09
0 0.1 0 1.2 0 1.2
2.8 2.0 1.8 2.6 1.8 3.2
7.09 ~ 9.85
0 0.2 0 1.4 0 1.4
3.0 2.2 2.0 2.6 2.0 3.4
9.85 ~ 12.41
0 0.2 0 1.4 0 1.4
3.5 2.4 2.2 3.0 2.2 3.8
12.41 ~ 15.75
0 0.2 0 1.6 0 1.6
B - 8 | Appendix B – Limits and Fits

1.4 Locational Interference Fits (LN)

Basic hole system. Limit dimensions are in thousandths of an inch.

Nominal Size Class LN1 Class LN2 Class LN3

Range Inches Standard Limits Standard Limits Standard Limits
Over To Hole Shaft Hole Shaft Hole Shaft
0.25 0.45 0.4 0.65 0.4 0.75
0 ~ 0.12
0 0.25 0 0.4 0 0.5
0.3 0.5 0.5 0.8 0.5 0.9
0.12 ~ 0.24
0 0.3 0 0.5 0 0.6
0.4 0.65 0.6 1.0 0.6 1.2
0.24 ~ 0.40
0 0.4 0 0.6 0 0.8
0.4 0.8 0.7 1.1 0.7 1.4
0.40 ~ 0.71
0 0.4 0 0.7 0 1.0
0.5 1.0 0.8 1.3 0.8 1.7
0.71 ~ 1.19
0 0.5 0 0.8 0 1.2
0.6 1.1 1.0 1.6 1.0 2.0
1.19 ~ 1.97
0 0.6 0 1.0 0 1.4
0.7 1.3 1.2 2.1 1.2 2.3
1.97 ~ 3.15
0 0.8 0 1.4 0 1.6
0.9 1.6 1.4 2.5 1.4 2.9
3.15 ~ 4.73
0 1.0 0 1.6 0 2.0
1.0 1.9 1.6 2.8 1.6 3.5
4.73 ~ 7.09
0 1.2 0 1.8 0 2.5
1.2 2.2 1.8 3.2 1.8 4.2
7.09 ~ 9.85
0 1.4 0 2.0 0 3.0
1.2 2.3 2.0 3.4 2.0 4.7
9.85 ~ 12.41
0 1.4 0 2.2 0 3.5
1.4 2.6 2.2 3.9 2.2 5.9
12.41 ~ 15.75
0 1.6 0 2.5 0 4.5
1.6 2.8 2.5 4.4 2.5 6.6
15.75 ~ 19.69
0 1.8 0 2.8 0 5.0
 Appendix B – Limits and Fits | B - 9

1.5 Forced Fits (FN)

Basic hole system. Limit dimensions are in thousandths of an inch.

Nominal Size Class FN1 Class FN2 Class FN3 Class FN4 Class FN5
Range Inches Standard Limits Standard Limits Standard Limits Standard Limits Standard Limits
Over To Hole Shaft Hole Shaft Hole Shaft Hole Shaft Hole Shaft

0 ~ 0.12
0.25 0.5 0.4 0.85 0.4 0.95 0.6 1.3
0 0.3 0 0.6 0 0.7 0 0.9
0.3 0.6 0.5 1.0 0.5 1.2 0.7 1.7
0.12 ~ 0.24
0 0.4 0 0.7 0 0.9 0 1.2
0.24 ~ 0.40
0.4 0.75 0.6 1.4 0.6 1.6 0.9 2.0
0 0.5 0 1.0 0 1.2 0 1.4
0.40 ~ 0.56
0.4 0.8 0.7 1.6 0.7 1.8 1.0 2.3
0 0.5 0 1.2 0 1.4 0 1.6
0.4 0.9 0.7 1.6 0.7 1.8 1.0 2.5
0.56 ~ 0.71
0 0.6 0 1.2 0 1.4 0 1.8
0.5 1.1 0.8 1.9 0.8 2.1 1.2 3.0
0.71 ~ 0.95
0 0.7 0 1.4 0 1.6 0 2.2
0.5 1.2 0.8 1.9 0.8 2.1 0.8 2.3 1.2 3.3
0.95 ~ 1.19
0 0.8 0 1.4 0 1.6 0 1.8 0 2.5
1.19 ~ 1.58
0.6 1.3 1.0 2.4 1.0 2.6 1.0 3.1 1.6 4.0
0 0.9 0 1.8 0 2.0 0 2.5 0 3.0
1.58 ~ 1.97
0.6 1.4 1.0 2.4 1.0 2.8 1.0 3.4 1.6 5.0
0 1.0 0 1.8 0 2.2 0 2.8 0 4.0
1.97 ~ 2.56
0.7 1.8 1.2 2.7 1.2 3.2 1.2 4.2 1.8 6.2
0 1.3 0 2.0 0 2.5 0 3.5 0 5.0
0.7 1.9 1.2 2.9 1.2 3.7 1.2 4.7 1.8 7.2
2.56 ~ 3.15
0 1.4 0 2.2 0 3.0 0 4.0 0 6.0
0.9 2.4 1.4 3.7 1.4 4.4 1.4 5.9 2.2 8.4
3.15 ~ 3.94
0 1.8 0 2.8 0 3.5 0 5.0 0 7.0
0.9 2.6 1.4 3.9 1.4 4.9 1.4 6.9 2.2 9.4
3.94 ~ 4.73
0 2.0 0 3.0 0 4.0 0 6.0 0 8.0
1.0 2.9 1.6 4.5 1.6 6.0 1.6 8.0 2.5 11.6
4.73 ~ 5.52
0 2.2 0 3.5 0 5.0 0 7.0 0 10.0
5.52 ~ 6.30
1.0 3.2 1.6 5.0 1.6 6.0 1.6 8.0 2.5 13.6
0 2.5 0 4.0 0 5.0 0 7.0 0 12.0
6.30 ~ 7.09
1.0 3.5 1.6 5.5 1.6 7.0 1.6 9.0 2.5 13.6
0 2.8 0 4.5 0 6.0 0 8.0 0 12.0
7.09 ~ 7.88
1.2 3.8 1.8 6.2 1.8 8.2 1.8 10.2 2.8 15.8
0 3.0 0 5.0 0 7.0 0 9.0 0 14.0
7.88 ~ 8.86
1.2 4.3 1.8 6.2 1.8 8.2 1.8 11.2 2.8 17.8
0 3.5 0 5.0 0 7.0 0 10.0 0 16.0
1.2 4.3 1.8 7.2 1.8 9.2 1.8 13.2 2.8 17.8
8.86 ~ 9.86
0 3.5 0 6.0 0 8.0 0 12.0 0 16.0
9.86 ~ 11.03
1.2 4.9 2.0 7.2 2.0 10.2 2.0 13.2 3.0 20.0
0 4.0 0 6.0 0 9.0 0 12.0 0 18.0
B - 10 | Appendix B – Limits and Fits

2. Metric Limits and Fits

2.1 Hole Basis Clearance Fits

All dimensions are in mm.

Locational
Loose Running Free Running Close Running Sliding
Basic Clearance
Size Hole Shaft Hole Shaft Hole Shaft Hole Shaft Hole Shaft
H11 c11 H9 d9 H8 f7 H7 g6 H7 h6
1 max 1.060 0.940 1.025 0.980 1.014 0.994 1.010 0.998 1.010 1.000
min 1.000 0.880 1.000 0.955 1.000 0.984 1.000 0.992 1.000 0.994
1.2 max 1.260 1.140 1.225 1.180 1.214 1.194 1.210 1.198 1.210 1.200
min 1.200 1.080 1.200 1.155 1.200 1.184 1.200 1.192 1.200 1.194
1.6 max 1.600 1.540 1.625 1.580 1.614 1.594 1.610 1.598 1.610 1.600
min 1.600 1.480 1.600 1.555 1.600 1.584 1.600 1.592 1.600 1.594
2 max 2.060 1.940 2.025 1.980 2.014 1.994 2.010 1.998 2.010 2.000
min 2.000 1.880 2.000 1.955 2.000 1.984 2.000 1.992 2.000 1.994
2.5 max 2.560 2.440 2.525 2.480 2.514 2.494 2.510 2.498 2.510 2.500
min 2.500 2.380 2.500 2.455 2.500 2.484 2.500 2.492 2.500 2.494
3 max 3.060 2.940 3.025 2.980 3.014 2.994 3.010 2.998 3.010 3.000
min 3.000 2.880 3.000 2.955 3.000 2.984 3.000 2.992 3.000 2.994
4 max 4.075 3.930 4.030 3.970 4.018 3.990 4.012 3.996 4.012 4.000
min 4.000 3.855 4.000 9.940 4.000 3.978 4.000 3.988 4.000 3.992
5 max 5.075 4.930 5.030 4.970 5.018 4.990 5.012 4.996 5.012 5.000
min 5.000 4.855 5.000 4.940 5.000 4.978 5.000 4.988 5.000 4.992
6 max 6.075 5.930 6.030 5.970 6.018 5.990 6.012 5.996 6.012 6.000
min 6.000 5.855 6.000 5.940 6.000 5.978 6.000 5.988 6.000 5.992
8 max 8.090 7.920 8.036 7.960 8.022 7.987 8.015 7.995 8.015 8.000
min 8.000 7.830 8.000 7.924 8.000 7.972 8.000 7.986 8.000 7.991
10 max 10.090 9.920 10.036 9.960 10.022 9.987 10.015 9.995 10.015 10.000
min 10.000 9.830 10.000 9.924 10.000 9.972 10.000 9.986 10.000 9.991
12 max 12.110 11.905 12.043 11.950 12.027 11.984 12.018 11.994 12.018 12.000
min 12.000 11.795 12.000 11.907 12.000 11.966 12.000 11.983 12.000 11.989
16 max 16.110 15.905 16.043 15.950 16.027 15.984 16.018 15.994 16.018 16.000
min 16.000 15.795 16.000 15.907 16.000 15.966 16.000 15.983 16.000 15.989
20 max 20.130 19.890 20.052 19.935 20.033 19.980 20.021 19.993 20.021 20.000
min 20.000 19.760 20.000 19.883 20.000 19.959 20.000 19.980 20.000 19.987
25 max 25.130 24.890 25.052 24.935 25.033 24.980 25.021 24.993 25.021 25.000
min 25.000 24.760 25.000 24.883 25.000 24.959 25.000 24.980 25.000 24.987
30 max 30.130 29.890 30.052 29.935 30.033 29.980 30.021 29.993 30.021 30.000
min 30.000 29.760 30.000 29.883 30.000 29.959 30.000 29.980 30.000 29.987
 Appendix B – Limits and Fits | B - 11

2.2 Hole Basis Transition and Interference Fits

All dimensions are in mm.

Locational Locational Locational
Medium Drive Force
Basic Transition Transition Interference
Size Hole Shaft Hole Shaft Hole Shaft Hole Shaft Hole Shaft
H7 k6 H7 n6 H7 p6 H7 s6 H7 u6
1 max 1.010 1.006 1.010 1.010 1.010 1.012 1.010 1.020 1.010 1.024
min 1.000 1.000 1.000 1.004 1.000 1.006 1.000 1.014 1.000 1.018
1.2 max 1.210 1.206 1.210 1.210 1.210 1.212 1.210 1.220 1.210 1.224
min 1.200 1.200 1.200 1.204 1.200 1.206 1.200 1.214 1.200 1.218
1.6 max 1.610 1.606 1.610 1.610 1.610 1.612 1.610 1.620 1.610 1.624
min 1.600 1.600 1.600 1.604 1.600 1.606 1.600 1.614 1.600 1.618
2 max 2.010 2.006 2.010 2.020 2.010 2.012 2.010 2.020 2.010 2.024
min 2.000 2.000 2.000 2.004 2.000 2.006 2.000 2.014 2.000 2.018
2.5 max 2.510 2.506 2.510 2.510 2.510 2.512 2.510 2.520 2.510 2.524
min 2.500 2.500 2.500 2.504 2.500 2.506 2.500 2.514 2.500 2.518
3 max 3.010 3.006 3.010 3.010 3.010 3.012 3.010 3.020 3.010 3.024
min 3.000 3.000 3.000 3.004 3.000 3.006 3.000 3.014 3.000 3.018
4 max 4.012 4.009 4.012 4.016 4.012 4.020 4.012 4.027 4.012 4.031
min 4.000 4.001 4.000 4.008 4.000 4.012 4.000 4.019 4.000 4.023
5 max 5.012 5.009 5.012 5.016 5.012 5.020 5.012 5.027 5.012 5.031
min 5.000 5.001 5.000 5.008 5.000 5.012 5.000 5.019 5.000 5.023
6 max 6.012 6.009 6.012 6.016 6.012 6.020 6.012 6.027 6.012 6.031
min 6.000 6.001 6.000 5.008 6.000 6.012 6.000 6.019 6.000 6.023
8 max 8.015 8.010 8.015 8.019 8.015 8.024 8.015 8.032 8.015 8.037
min 8.000 8.001 8.000 8.010 8.000 8.015 8.000 8.023 8.000 8.028
10 max 10.015 10.010 10.015 10.019 10.015 10.024 10.015 10.032 10.015 10.037
min 10.000 10.001 10.000 10.010 10.010 10.015 10.000 10.023 10.000 10.028
12 max 12.018 12.012 12.018 12.023 12.018 12.029 12.018 12.039 12.018 12.044
min 12.000 12.001 12.000 12.012 12.000 12.018 12.000 12.028 12.000 12.033
16 max 16.018 16.012 16.018 16.023 16.018 16.029 16.018 16.039 16.018 16.044
min 16.000 16.001 16.000 16.012 16.000 16.018 16.000 16.028 16.000 16.033
20 max 20.021 20.015 20.021 20.028 20.021 20.035 20.021 20.048 20.021 20.054
min 20.000 20.002 20.000 20.015 20.000 20.022 20.000 20.035 20.000 20.041
25 max 25.021 25.015 25.021 25.028 25.021 25.035 25.021 25.048 25.021 25.061
min 25.000 25.002 25.000 25.015 25.000 25.022 25.000 25.035 25.000 25.048
30 max 30.021 30.015 30.021 30.021 30.028 30.035 30.021 30.048 30.021 30.061
min 30.000 30.002 30.000 30.000 30.015 30.022 30.000 30.035 30.000 30.048
B - 12 | Appendix B – Limits and Fits

2.3 Shaft Basis Clearance Fits

All dimensions are in mm.

Locational
Loose Running Free Running Close Running Sliding
Basic Clearance
Size Hole Shaft Hole Shaft Hole Shaft Hole Shaft Hole Shaft
C11 h11 D9 h9 F8 h7 G7 h6 H7 h6
1 max 1.120 1.000 1.045 1.000 1.020 1.000 1.012 1.000 1.010 1.000
min 1.060 0.940 1.020 0.975 1.006 0.990 1.002 0.994 1.000 0.994
1.2 max 1.320 1.200 1.245 1.200 1.220 1.200 1.212 1.200 1.210 1.200
min 1.260 1.140 1.220 1.175 1.206 1.190 1.202 1.194 1.200 1.194
1.6 max 1.720 1.600 1.645 1.600 1.620 1.600 1.612 1.600 1.610 1.600
min 1.660 1.540 1.620 1.575 1.606 1.590 1.602 1.594 1.600 1.594
2 max 2.120 2.000 2.045 2.000 2.020 2.000 2.012 2.000 2.010 2.000
min 2.060 1.940 2.020 1.975 2.006 1.990 2.002 1.994 2.000 1.994
2.5 max 2.620 2.500 2.545 2.500 2.520 2.500 2.512 2.500 2.510 2.500
min 2.560 2.440 2.520 2.475 2.506 2.490 2.502 2.494 2.500 2.494
3 max 3.120 3.000 3.045 3.000 3.020 3.000 3.012 3.000 3.010 3.000
min 3.060 2.940 3.020 2.975 3.006 2.990 3.002 2.994 3.000 2.994
4 max 4.145 4.000 4.060 4.000 4.028 4.000 4.016 4.000 4.012 4.000
min 4.070 3.925 4.030 3.970 4.010 3.988 4.004 3.992 4.000 3.992
5 max 5.145 5.000 5.060 5.000 5.028 5.000 5.016 5.000 5.012 5.000
min 5.070 4.925 5.030 4.970 5.010 4.988 5.004 4.992 5.000 4.992
6 max 6.145 6.000 6.060 6.000 6.028 6.000 6.016 6.000 6.012 6.000
min 6.070 5.925 6.030 5.970 6.010 5.988 6.004 5.992 6.000 5.992
8 max 8.170 8.000 8.076 8.000 8.035 8.000 8.020 8.000 8.015 8.000
min 8.080 7.910 8.040 7.964 8.013 7.985 8.005 7.991 8.000 7.991
10 max 10.170 10.000 10.076 10.000 10.035 10.000 10.020 10.000 10.015 10.000
min 10.080 9.910 10.040 9.964 10.013 9.985 10.005 9.991 10.000 9.991
12 max 12.205 12.000 12.093 12.000 12.043 12.000 12.024 12.000 12.018 12.000
min 12.095 11.890 12.050 11.957 12.016 11.982 12.006 11.989 12.000 11.989
16 max 16.205 16.000 16.093 16.000 16.043 16.000 16.024 16.000 16.018 16.000
min 16.095 15.890 16.050 15.957 16.016 15.982 16.006 15.989 16.000 15.989
20 max 20.240 20.000 20.117 20.000 20.053 20.000 20.028 20.000 20.021 20.000
min 20.110 19.870 20.065 19.948 20.020 19.979 20.007 19.987 20.000 19.987
25 max 25.240 25.000 25.117 25.000 25.053 25.000 25.028 25.000 25.021 25.000
min 25.110 24.870 25.065 24.948 25.020 24.979 25.007 24.987 25.000 24.987
30 max 30.240 30.000 30.117 30.000 30.053 30.000 30.028 30.000 30.021 30.000
min 30.110 29.870 30.065 29.948 30.020 29.979 30.007 29.987 30.000 29.987
 Appendix B – Limits and Fits | B - 13

2.4 Shaft Basis Transition and Interference Fits

All dimensions are in mm.

Locational Locational Locational
Medium Drive Force
Basic Transition Transition Interference
Size Hole Shaft Hole Shaft Hole Shaft Hole Shaft Hole Shaft
K7 h6 N7 h6 P7 h6 S7 h6 U7 h6
1 max 1.000 1.000 0.996 1.000 0.994 1.000 0.986 1.000 0.982 1.000
min 0.990 0.994 0.986 0.994 0.984 0.994 0.976 0.994 0.972 0.994
1.2 max 1.200 1.200 1.196 1.200 1.194 1.200 1.186 1.200 1.182 1.200
min 1.190 1.194 1.186 1.194 1.184 1.194 1.176 1.194 1.172 1.194
1.6 max 1.600 1.600 1.596 1.600 1.594 1.600 1.586 1.600 1.582 1.600
min 1.590 1.594 1.586 1.594 1.584 1.594 1.576 1.594 1.572 1.594
2 max 2.000 2.000 1.996 2.000 1.994 2.000 1.986 2.000 1.982 2.000
min 1.990 1.994 1.986 1.994 1.984 1.994 1.976 1.994 1.972 1.994
2.5 max 2.500 2.500 2.496 2.500 2.494 2.500 2.486 2.500 2.482 2.500
min 2.490 2.494 2.486 2.494 2.484 2.494 2.476 2.494 2.472 2.494
3 max 3.000 3.000 2.996 3.000 2.994 3.000 2.986 3.000 2.982 3.000
min 2.990 2.994 2.986 2.994 2.984 2.994 2.976 2.994 2.972 2.994
4 max 4.003 4.000 3.996 4.000 3.992 4.000 3.985 4.000 3.981 4.000
min 3.991 5.992 3.984 3.992 3.980 3.992 3.973 3.992 3.969 3.992
5 max 5.003 5.000 4.996 5.000 4.992 5.000 4.985 5.000 4.981 5.000
min 4.991 4.992 4.984 4.992 4.980 4.992 4.973 4.992 4.969 4.992
6 max 6.003 6.000 5.996 6.000 5.992 6.000 5.985 6.000 5.981 6.000
min 5.991 5.992 5.984 5.992 5.980 5.992 5.973 5.992 5.969 5.992
8 max 8.005 8.000 7.996 8.000 7.991 8.000 7.983 8.000 7.978 8.000
min 7.990 7.991 7.981 7.991 7.976 7.991 7.968 7.991 7.963 7.991
10 max 10.005 10.000 9.996 10.000 9.991 10.000 9.983 10.000 9.978 10.000
min 9.990 9.991 9.981 9.991 9.976 9.991 9.968 9.991 9.963 9.991
12 max 12.006 12.000 11.995 12.000 11.989 12.000 11.979 12.000 11.974 12.000
min 11.988 11.989 11.977 11.989 11.971 11.989 11.961 11.989 11.956 11.989
16 max 16.006 16.000 15.995 16.000 15.989 16.000 15.979 16.000 15.974 16.000
min 15.988 15.989 15.977 15.989 15.971 15.989 15.961 15.989 15.956 15.989
20 max 20.006 20.000 19.993 20.000 19.986 20.000 19.973 20.000 19.967 20.000
min 19.985 19.987 19.972 19.987 19.965 19.987 19.952 19.987 19.946 19.987
25 max 25.006 25.000 24.993 25.000 24.986 25.000 24.973 25.000 24.960 25.000
min 24.985 24.987 24.972 24.987 24.965 24.987 24.952 24.987 24.939 24.987
30 max 30.006 30.000 29.993 30.000 29.986 30.000 29.973 30.000 29.960 30.000
min 29.985 29.987 29.972 29.987 29.965 29.987 29.952 29.987 29.939 29.987
B - 14 | Appendix B – Limits and Fits

Notes: