Dynapav 150 PDF

Instruction manual
Operating & Maintenance

4812159601_E.pdf
Vibratory roller
CC224HF/324HF/384HF
CC2200/3200/3800
Engine
Cummins QSB 3.3 (IIIA/T3)
Deutz TCD 3.6 L04 (IIIB/T4i), (IIIB/T4f)
Serial number
10000311xxA009344 -
10000315xxA009393 -
10000319xxA009520 -
10000336xxA012872 -
10000340xxA010700 -
10000344xxA012937 -
10000423xxA020964 -
10000427xxA021816 -
Translation of original instruction
Reservation for changes

Printed in Sweden
Table of Contents
Introduction .............................................................................................................................. 1
The machine ............................................................................................... 1
Intended use ............................................................................................... 1
Warning symbols......................................................................................... 1
Safety information ....................................................................................... 1
General ....................................................................................................... 2
CE marking and Declaration of conformity.................................................. 3
Safety - General instructions.................................................................................................... 5
Safety - when operating ........................................................................................................... 7
Driving near edges ...................................................................................... 7
Work driving ................................................................................................ 7
Safety (Optional) ...................................................................................................................... 9
Air conditioning............................................................................................ 9
Edge cutter/compactor ................................................................................ 9
Working lights - Xenon .............................................................................. 10
Special instructions ................................................................................................................ 11
Standard lubricants and other recommended oils and fluids .................... 11
Higher ambient temperatures, above +40°C (104°F)................................ 11
Lower ambient temperature - Freeze risk ................................................. 11
Temperatures............................................................................................ 11
High pressure cleaning ............................................................................. 12
Fire fighting ............................................................................................... 12
Roll Over Protective Structure (ROPS), ROPS approved cab .................. 12
Battery handling ........................................................................................ 12
Jump starting (24V)................................................................................... 13
Technical specifications ......................................................................................................... 15
Vibrations - Operator station ..................................................................... 15
Noise level................................................................................................. 15
Electrical system ....................................................................................... 15
Slopes ....................................................................................................... 16
2018-04-25 4812159601_E.pdf
e-
Dimensions, side view............................................................................... 16
Dimensions, top view ................................................................................ 17
Weights and volumes................................................................................ 18
Working capacity....................................................................................... 18
General ..................................................................................................... 19
Hydraulic system....................................................................................... 20
Air Conditioning / Automatic Climate Control (ACC) (Optional) ................ 20
Tightening torque ...................................................................................... 21
Machine description ............................................................................................................... 23
Diesel engine ............................................................................................ 23
Electrical system ....................................................................................... 23
Propulsion system..................................................................................... 23
Brake system ............................................................................................ 24
Steering system ........................................................................................ 24
Vibration system........................................................................................ 24
Cab............................................................................................................ 24
ROPS ........................................................................................................ 24
Identification ............................................................................................................ 25
Product and component plates ................................................................. 25
Product identification number on the frame .............................................. 26
Machine plate............................................................................................ 26
Explanation of 17PIN serial number.......................................................... 26
Engine plates ............................................................................................ 27
Decals...................................................................................................................... 28
Location - decals ....................................................................................... 28
Safety decals............................................................................................. 29
Info decals................................................................................................. 31
Instruments/Controls ............................................................................................... 32
Control panel and controls ........................................................................ 32
Function descriptions ................................................................................ 33
4812159601_E.pdf 2018-04-25
e-
Forward & Reverse lever .......................................................................... 37
Forward & Reverse lever .......................................................................... 38
Display explanations ................................................................................. 38
Machine alarm........................................................................................... 42
"MAIN MENU" ........................................................................................... 43
"USER SETTINGS" .................................................................... 44
"MACHINE SETTINGS".............................................................. 45
"SERVICE MENU" ...................................................................... 45
"ABOUT"..................................................................................... 47
Operator help when starting...................................................................... 47
Operator help Workmode.......................................................................... 47
Instruments and controls, cab ................................................................... 48
Function description of instruments and controls in the cab ..................... 49
Using the cab controls............................................................................... 50
Defroster ..................................................................................... 50
Heat ............................................................................................ 50
AC/ACC ...................................................................................... 50
Electrical system (version 1).................................................................................... 51
Fuse boxes in main switchbox .................................................................. 51
Electrical system (version 2).................................................................................... 52
Fuse card in main switchbox..................................................................... 52
Power in engine compartment/battery compartment ................................ 53
Main fuse panel (Cummins) ...................................................................... 53
Fuse box at master switch (Deutz)............................................................ 54
Fuses in cab.............................................................................................. 55
Operation ............................................................................................................................... 57
Before starting ......................................................................................................... 57
Master switch - Switching on..................................................................... 57
2018-04-25 4812159601_E.pdf
e-
Control panel, adjustments ....................................................................... 57
Operator's seat - Adjustment..................................................................... 58
Belt reminder............................................................................................. 58
Operator's seat, comfort - Adjustments..................................................... 59
Parking brake ............................................................................................ 59
Display - Control........................................................................................ 60
Interlock..................................................................................................... 61
Operator position....................................................................................... 62
View .......................................................................................................... 62
Starting .................................................................................................................... 63
Starting the engine .................................................................................... 63
Display when activating choice via the button set..................................... 64
Alarm descriptions..................................................................................... 65
Driving ..................................................................................................................... 65
Operating the roller ................................................................................... 65
Interlock/Emergency stop/Parking brake - Check ..................................... 67
Pivotal steering (Optional)......................................................................... 68
Edge cutting (Optional) ............................................................................. 68
Vibration .................................................................................................................. 69
Manual/Automatic vibration....................................................................... 69
Manual vibration - Switching on ................................................................ 70
Amplitude/frequency - Changeover........................................................... 70
Braking .................................................................................................................... 70
Normal braking.......................................................................................... 70
Emergency braking ................................................................................... 71
Switching off.............................................................................................. 71
Parking .................................................................................................................... 72
Chocking the drums .................................................................................. 72
Master switch ............................................................................................ 72
Long-term parking.................................................................................................................. 73
4812159601_E.pdf 2018-04-25
e-
Engine ....................................................................................................... 73
Battery....................................................................................................... 73
Air cleaner, exhaust pipe........................................................................... 73
Watering system ....................................................................................... 73
Fuel tank ................................................................................................... 73
Hydraulic reservoir .................................................................................... 73
Hoods, tarpaulin ........................................................................................ 74
Steering cylinder, hinges, etc. ................................................................... 74
Miscellaneous ........................................................................................................................ 75
Lifting ....................................................................................................................... 75
Locking the articulation ............................................................................. 75
Lifting the roller.......................................................................................... 76
Lifting the roller with jack:.......................................................................... 76
Unlocking the articulation .......................................................................... 77
Towing/Recovering.................................................................................................. 77
Short distance towing with the engine running.......................................... 78
Short distance towing when the engine is inoperative. ............................. 79
Towing the roller........................................................................................ 79
Trailer eye ................................................................................................. 80
Transport ................................................................................................................. 80
Loading CC224-624, CC2200-6200.......................................................... 81
Operating instructions - Summary ......................................................................................... 83
Preventive maintenance ........................................................................................................ 85
Acceptance and delivery inspection.......................................................... 85
Warranty.................................................................................................... 85
Maintenance - Lubricants and symbols ................................................................................. 87
Maintenance symbols ............................................................................... 88
Maintenance - Maintenance schedule ................................................................................... 89
Service and maintenance points ............................................................... 89
General ..................................................................................................... 89
2018-04-25 4812159601_E.pdf
e-
Every 10 hours of operation (Daily)........................................................... 90
After the FIRST 50 hours of operation ...................................................... 90
Every 50 hours of operation (Weekly)....................................................... 91
Every 250 hours of operation (Monthly) .................................................... 91
Every 500/1500 hours of operation ........................................................... 92
Every 1000 hours of operation (Every six months) ................................... 92
Every 2000 hours of operation .................................................................. 93
Maintenance, 10h .................................................................................................................. 95
Diesel engine - Check oil level .................................................................. 95
Coolant level - Check ................................................................................ 96
Fuel tank - Refueling ................................................................................. 96
Water tank, Std - Filling............................................................................. 97
Hydraulic reservoir - Check fluid level....................................................... 97
Sprinkler system/Drum
Check ........................................................................................................ 98
Cleaning the coarse filter .......................................................................... 98
Cleaning of sprinkler nozzle ...................................................................... 99
Emergency watering (Accessory) - Extra pump in pump system............ 100
Scrapers, spring-action
Check ...................................................................................................... 100
Scrapers
Setting - Adjustment................................................................................ 101
Maintenance - 50h ............................................................................................................... 103
Fuel filter - Draining................................................................................. 103
Drum gear - Checking the oil level .......................................................... 104
Maintenance - 250h ............................................................................................................. 105
Diesel engine
Oil change ............................................................................................... 105
Engine
Replacing oil filter.................................................................................... 106
4812159601_E.pdf 2018-04-25
e-
Hydraulic fluid cooler
Checking - Cleaning................................................................................ 106
Battery
- Check condition .................................................................................... 107
Air conditioning (Optional)
- Inspection.............................................................................................. 107
Drying filter - Inspection .......................................................................... 108
Edge cutter (Optional)
- Lubrication ............................................................................................ 108
Maintenance - 500h ............................................................................................................. 109
Diesel engine
Oil change ............................................................................................... 109
Engine
The engine fuel filter - replacement/cleaning .......................................... 110
Battery
- Check condition .................................................................................... 111
Air cleaner
Checking - Change the main air filter...................................................... 112
Backup filter - Change............................................................................. 112
Air cleaner
- Cleaning................................................................................................ 113
Drum - oil level
Inspection - filling .................................................................................... 113
Rubber elements and attachment screws
Check ...................................................................................................... 114
Seat bearing - Lubrication ....................................................................... 114
Pivot bearing (Optional) - Lubrication...................................................... 115
Hydraulic reservoir cap - Check .............................................................. 115
- Inspection.............................................................................................. 116
2018-04-25 4812159601_E.pdf
e-
- Lubrication ............................................................................................ 117
Maintenance - 1000h ........................................................................................................... 119
Diesel engine
Oil change ............................................................................................... 119
Engine
Battery
- Check condition .................................................................................... 121
Air cleaner
Air cleaner
- Cleaning................................................................................................ 123
Hydraulic filter
Change.................................................................................................... 124
Drum - Oil change ................................................................................... 125
Drum gear - Oil change........................................................................... 125
Check ...................................................................................................... 126
Steering hitch - Tightening ...................................................................... 128
Cab
Fresh air filter - Replacing ....................................................................... 129
- Overhaul ............................................................................................... 129
4812159601_E.pdf 2018-04-25
e-
- Lubrication ............................................................................................ 130
Maintenance - 2000h ........................................................................................................... 131
Diesel engine
Oil change ............................................................................................... 131
Engine
Battery
- Check condition .................................................................................... 133
Air cleaner
Air cleaner
- Cleaning................................................................................................ 135
Hydraulic filter
Change.................................................................................................... 136
Drum - Oil change ................................................................................... 137
Drum gear - Oil change........................................................................... 137
Check ...................................................................................................... 138
Hydraulic reservoir
Fluid change............................................................................................ 140
Fuel tank
- Cleaning............................................................................................... 141
Watering system
- Draining................................................................................................ 141
2018-04-25 4812159601_E.pdf
e-
Water tank - Cleaning ............................................................................. 142
Steering joint - Check.............................................................................. 142
Steering hitch - Tightening ...................................................................... 143
Cab
Fresh air filter - Replacing ....................................................................... 143
- Overhaul ............................................................................................... 144
- Lubrication ............................................................................................ 145
4812159601_E.pdf 2018-04-25
e-
Introduction
Introduction
The machine
Dynapac CC224HF/324HF/384HF,
CC2200/3200/3800 is a self-propelled vibratory
tandem roller in 8/8/9.5 metric tonnes class featuring
1500/1730/1730 mm (59/68/68 in) wide drums. The
machine is equipped with drive, brakes, vibration and
timer for water sprinkler on both drums.
CC224HF/324HF, CC2200/3200 is also available as
Combi with four rubber wheels at rear replacing the
steel drum.
A variety of different engine power settings, operator
platforms, control possibilities and options makes the
machine available in a lot of different configurations.
Intended use
The machine is mainly designed to be used for thin
and thick asphalt layers with regards to dual vibration
amplitudes that are optimized for this purpose. It is
also possible to compact granular soil material, such
as sand and gravel.
Warning symbols
WARNING ! Marks a danger or a hazardous

procedure that can result in life threatening or
serious injury if the warning is ignored.
CAUTION ! Marks a danger or hazardous

procedure that can result in damage to the
machine or property if the warning is ignored.
Safety information
It is recommended to at least train operators in

handling and daily maintenance of the machine
in accordance with the instruction manual.
Passengers are not allowed on the machine, and
you must sit in the seat when operating the
machine.
The safety manual supplied with the machine

must be read by all roller operators. Always
follow the safety instructions. Do not remove
the manual from the machine.
2018-04-25 4812159601_E.pdf
1
Introduction
We recommend that the operator reads the

safety instructions in this manual carefully.
Always follow the safety instructions. Ensure
that this manual is always easily accessible.
Read the entire manual before starting the

machine and before carrying out any
maintenance.
Replace immediately the instruction manuals if

lost, damaged or unreadable.
Ensure good ventilation (extraction of air by fan)

where the engine is run indoors.
General
This manual contains instructions for machine
operation and maintenance.
The machine must be correctly maintained for
maximal performance.
The machine should be kept clean so that any
leakages, loose bolts and loose connections are
discovered at as early a point in time as possible.
Inspect the machine every day, before starting.
Inspect the entire machine so that any leakages or
other faults are detected.
Check the ground under the machine. Leakages are
more easily detected on the ground than on the
machine itself.
THINK ENVIRONMENT ! Do not release oil,

fuel and other environmentally hazardous
substances into the environment. Always send
used filters, drain oil and fuel remnants to
environmentally correct disposal.
This manual contains instructions for periodic

maintenance, where maintenance after every 10 and
50 hours of operation can be performed by the
machine operator. Other maintenance intervals must
be carried out by accredited (Dynapac) service
personnel.
4812159601_E.pdf 2018-04-25
2
Introduction
Additional instructions for the engine can be

found in the manufactuer's engine manual.
Specific maintenance and checks on diesel
engines must be carried out by the engine
supplier’s certified personnel.
CE marking and Declaration of conformity

(Applies to machines marketed in EU/EEC)
This machine is CE marked. This shows that on
delivery it complies with the basic health and safety
directives applicable for the machine in accordance
with machinery directive 2006/42/EC and that it also
complies with other regulations and directives
applicable for this machine.
A "Declaration of conformity" is supplied with this
machine, which specifies the applicable regulations
and directives with supplements, as well as the
harmonized standards and other regulations that are
applied and according to the regulations must be
declared in writing.
2018-04-25 4812159601_E.pdf
3
Introduction
4812159601_E.pdf 2018-04-25
4
Safety - General instructions

(Also read the safety manual)
1. The operator must be familiar with the contents of the OPERATION section
before starting the roller.
2. Ensure that all instructions in the MAINTENANCE section are followed.
3. Only trained and/or experienced operators are to operate the roller.

Passengers are not permitted on the roller. Remain seated at all times when
operating the roller.
4. Never use the roller if it is in need of adjustment or repair.
5. Only mount and dismount the roller when it is stationary. Use the intended
footsteps, grips and rails. Always use the three-point grip (both feet and one
hand, or one foot and both hands) when mounting or dismounting the
machine. Never jump down from the machine.
6. The ROPS (Roll Over Protective Structure) should always be used when the
machine is operated on unsafe ground.
7. Drive slowly in sharp bends.
8. Avoid driving across slopes. Drive straight up or straight down the slope.
9. Never operate with roller outside the edge, if the substrate does not have full
bearing strength or is close to a slope. Avoid operating close to edges and
ditches and the like as well as on poor ground conditions that influence the
bearing strength and capacity to support the roller.
10. Make sure that there are no obstacles in the direction of travel, on the
ground, in front of or behind the roller, or overhead.
11. Drive particularly carefully on uneven ground.
12. Use the safety equipment provided. The seat belt must be worn on machines
fitted with ROPS/ROPS-cab.
13. Keep the roller clean. Clean any dirt or grease that accumulates on the
operator platform immediately. Keep all signs and decals clean and legible.
14. Safety measures before refueling:

- Stop the engine
- Do not smoke.
- No naked flames in the vicinity of the roller.
- Earth the filling equipment nozzle to the tank opening to avoid sparks.
15. Before repairs or service:

- Chock the drums/wheels.
- Lock the articulation if necessary.
- Place blocks under overhanging equipment, such as strike-off blade and
chip spreader.
2018-04-25 4812159601_E.pdf
5
16. Hearing protection is recommended if the noise level exceeds 80 dB(A). The
noise level can vary depending on the equipment on the machine and the
surface the machine is being used on.
17. Do not make any changes or modifications to the roller that could affect
safety. Changes are only to be made after written approval has been given
by Dynapac.
18. Avoid using the roller before the hydraulic fluid has reached its normal
working temperature. Braking distances can be longer than normal when the
fluid is cold. See instructions in the STOP section.
19. For your own protection always wear:

- helmet
- working boots with steel toecaps
- ear protectors
- reflecting clothing/high visibility jacket
- working gloves
4812159601_E.pdf 2018-04-25
6
Safety - when operating
Prevent persons from entering or remaining in

the danger area, i.e. a distance of at least 7 m
(23 ft) in all directions from operating machines.
The operator may allow a person to remain in
the risk zone, however he/she must be attentive
and operate the machine only when the person
is fully visible or has given a clear indication of
where he or she is.
Avoid driving across a slope. Drive straight up

and down sloping ground.
Driving near edges

Never operate with roller outside the edge, if the
substrate does not have full bearing strength or is
close to a slope.
Keep in mind that the machine's center of gravity

moves outwards when steering. For example, the
center of gravity moves to the right when you steer
to the left.
Work driving
Avoid operating close to edges and ditches and the
like as well as on poor ground conditions that influence
the bearing strength and capacity to support the roller.
Pay attention to potential obstacles above the
machine, such as overhead cables and the branches
of trees etc.
Pay particular attention to the stability of the substrate
when compacting close to edges and holes. Do not
compact with a large overlap from the previous track in
order to maintain roller stability. Consider other
compaction methods such as remote-control or a
walk-behind roller close to steep slopes or where the
bearing strength of the substrate is unknown.
2018-04-25 4812159601_E.pdf
7
To exit the cab in an emergency, release the

hammer on the rear right post and break the rear
window.
It is recommended that ROPS (Roll Over Protective

Structure) or a ROPS-approved cab is always used
when driving on slopes or unsafe ground. Always
wear a seat belt.
4812159601_E.pdf 2018-04-25
8
Safety (Optional)
Safety (Optional)
Air conditioning
The system contains pressurized refrigerant. It is

forbidden to release refrigerants into the
atmosphere.
Work on the refrigerant circuit is only to be carried

out by authorized companies.
The cooling system is pressurized. Incorrect

handling can result in serious personal injury. Do
not disconnect or undo the hose couplings.
Fig. Air conditioning (ACC)
The system must be re-filled with an approved

refrigerant by authorized personnel when
necessary. See decal on or in the vicinity of the
installation.
Edge cutter/compactor
The operator must make sure that nobody is in the
area of operation while the machine is in use.
3 The edge cutter consists of rotating components

and there is a risk of being crushed.
1 The tool must be returned to the transport

2 position (raised position) (1) every time it has
been used.
Fig. Edge cutter/compactor
1. Transport position
2. Operating position
3. Holder for cutter/compactor wheel. If the edge cutter and its parts are dismantled,
make sure that it is set in a relieved position and
resting on the ground.
2018-04-25 4812159601_E.pdf
9
Safety (Optional)
Working lights - Xenon
Warning, high voltage!
The working lights of the Xenon type have a

secondary high-voltage source.
Work on the lighting should only be conducted by an
authorized electrician and with the primary voltage
disconnected.
Contact a Dynapac dealer!
Figure. Xenon lighting on cab
Warning, environmentally hazardous waste!
Working lights of the Xenon type include a discharge

lamp that contains mercury (Hg).
A defective lamp is to be considered as hazardous
waste and shall be disposed off as per local directives.
4812159601_E.pdf 2018-04-25
10
Special instructions
Standard lubricants and other recommended

oils and fluids
Before leaving the factory, the systems and
components are filled with the oils and fluids specified
in the lubricant specification. These are suitable for
ambient temperatures in the range -15°C to +40°C
(5°F - 105°F).
The maximum ambient temperature for

biological hydraulic fluid is +35°C (95°F).
Higher ambient temperatures, above +40°C

(104°F)
For operation of the machine at higher ambient
temperatures, however maximum +50°C (122°F), the
following recommendations apply:
The diesel engine can be run at this temperature using
normal oil. However, the following fluids must be used
for other components:
Hydraulic system - mineral oil Shell Tellus S2V100 or
similar.
Lower ambient temperature - Freeze risk

Make sure that the watering system is empty/drained
of water (sprinkler, hoses, tank/s) or that anti-freeze
has been added, to prevent the system freezing.
The outlet hose from the central tank can be
disconnected and the end placed in a container with
antifreeze to run this through the pump/filter.
Temperatures
The temperature limits apply to standard versions of
rollers.
Rollers equipped with additional equipment, such as
noise suppression, may need to be more carefully
monitored in the higher temperature ranges.
2018-04-25 4812159601_E.pdf
11
High pressure cleaning

Do not spray directly onto electrical components.
Do not use high pressure cleaning for
dashboard/display.
The Electrical Drive Control and the computer

box may not be washed with high pressure
cleaning and not at all with water. Clean them
with a dry wiper.
Detergent that can destroy electrical parts, or

which is conductive, must not be used.
Place a plastic bag over the fuel filler cap and secure
with a rubber band. This is to avoid high pressure
water entering the vent hole in the filler cap. This could
cause malfunctions, such as the blocking of filters.
Never aim the water jet directly at the fuel tank

cap, or into exhaust pipe. This is particularly
important when using a high-pressure cleaner.
Fire fighting
If the machine catches fire, use an ABC-class powder
fire extinguisher.
A BE-class carbon dioxide fire extinguisher can also
be used.
Roll Over Protective Structure (ROPS), ROPS

approved cab
If the machine is fitted with a Roll Over

Protective Structure (ROPS, or ROPS approved
cab) never carry out any welding or drilling in
the structure or cab.
Never attempt to repair a damaged ROPS

structure or cab. These must be replaced with
new ROPS structure or cabs.
Battery handling
When removing batteries, always disconnect the

negative cable first.
4812159601_E.pdf 2018-04-25
12
When fitting batteries, always connect the

positive cable first.
Dispose of old batteries in an environmentally

friendly way. Batteries contain toxic lead.
Do not use a quick-charger for charging the

battery. This may shorten battery life.
Jump starting (24V)
Do not connect the negative cable to the

negative terminal on the dead battery. A spark
can ignite the oxy-hydrogen gas formed
around the battery.
Check that the battery used for jump starting

has the same voltage as the dead battery.
2 1
Turn the ignition and all power consuming equipment
off. Switch off the engine on the machine which is
12V providing jump start power.
Jump leads must have 24V.
3 24V First connect the jump start battery's positive terminal
(1) to the flat battery's positive terminal (2).Then
12V connect the jump start battery's negative terminal (3)
to, for example, a bolt (4) or the lifjting eye on the
machine with the flat battery.
4 Start the engine on the power providing machine. Let it
run for a while. Now try to start the other machine.
Fig. Jump starting Disconnect the cables in the reverse order.
2018-04-25 4812159601_E.pdf
13
4812159601_E.pdf 2018-04-25
14
Technical specifications
Vibrations - Operator station

(ISO 2631)
The vibration levels are measured in accordance with the operational cycle described in
EU directive 2000/14/EC on machines equipped for the EU market, with vibration switched
on, on soft polymer material and with the operator’s seat in the transport position.
Measured whole-body vibrations are below the action value of 0.5 m/s² as specified in Directive
2002/44/EC. (Limit is 1.15 m/s²)
Measured hand/arm vibrations also were below the action level of 2.5 m/s² specified in the same
directive. (Limit is 5 m/s²)
Noise level
The noise level is measured in accordance with the operational cycle described in
EU directive 2000/14/EC on machines equipped for the EU market, on soft polymer
material with vibration switched on and the operator's seat in the transport position.
Guaranteed sound power level, LwA 60kW 106 dB (A)

74/75kW 107 dB (A)
Sound pressure level at the operator's ear (platform), LpA 91 ±3 dB (A)
Sound pressure level at the operator's ear (cab), LpA 85 ±3 dB (A)
During operation the above values may differ because of the actual operational
conditions.
Electrical system
Machines are EMC tested in accordance with EN
13309:2000 'Construction machinery'
2018-04-25 4812159601_E.pdf
15
Slopes
This angle has been measured on a hard, flat surface
with the machine stationary.
The steering angle was zero, the vibration was
Max 20° or 36% switched OFF and all tanks were full.
Always take into consideration that loose ground,
steering the machine, vibration on, machine speed
across the ground and raising the center of gravity can
all cause the machine to topple at smaller slope
angles than those specified here.
Dimensions, side view
Dimensions mm in
A Wheel base 3340 131
D Diameter, drum 1150 45
H1 Height, with ROPS/cab 2990 118
H2 Height, without ROPS/cab 2275 90
K Ground clearance 310 12
L Length, standard variant 4490 177
S Thickness, drum amplitude, Nominal 18 0.7
4812159601_E.pdf 2018-04-25
16
Dimensions, top view
Dimensions mm in
B1 Machine width, standard
CC224HF, CC2200 1620 64
CC324HF/384HF, CC3200/3800 1870 74
B2 Machine width, asymmetrical 2145 84.5
R1 Turning radius, outer
CC224HF, CC2200 6570 / 5190* 259 / 204*
CC324HF, CC3200 6685 / 5305* 263 / 209*
CC384HF, CC3800 6685 263
R2 Turning radius, inner
CC224HF, CC2200 5570 / 3225* 219 / 127*
CC324HF, CC3200 - -
CC384HF, CC3800 - -
W Drum width
CC224HF, CC2200 1500 59
CC324HF/384HF, CC3200/3800 1730 68
*) with offset
2018-04-25 4812159601_E.pdf
17
Weights and volumes
Weights
Service weight without ROPS ROPS Cab
(EN500)
CC224HF, STD (kg) 7 300 7 600 7 800
CC2200
(lbs) 16 100 16 760 17 200
OFFSET (kg) 7 800 8 100 8 300
(lbs) 17 200 17 860 18 300
CC324HF, STD (kg) 7 800 8 100 8 300
CC3200
(lbs) 17 200 17 860 18 300
OFFSET (kg) 8 300 8 600 8 900
(lbs) 18 300 18 960 19 630
CC384HF, STD (kg) 9 100 9 400 9 600
CC3800
(lbs) 20 070 20 730 21 170
Fluid volumes
Fuel tank 130 liters 34 gal
Water tank 750 liters 198 gal
Working capacity
Compaction data
Static linear load (Front) (Rear)
CC224HF, CC2200 25,7 25,7 (kg/cm)
144 144 (pli)
CC324HF, CC3200 23,6 23,6 (kg/cm)
132 132 (pli)
CC384HF, CC3800 27,2 27,2 (kg/cm)
152 152 (pli)
Amplitude High Low Low(CE-2006)

0,7 0,3 0,2 (mm)
0.028 0.012 0.008 (in)
4812159601_E.pdf 2018-04-25
18
Vibration frequency High High Low Low

amplitude amplitude amplitude amplitude
(CE-2006) (CE-2006)
48 48 67 61 (Hz)
2 850 2 850 4 020 3 660 (vpm)
Centrifugal force High High Low Low

amplitude amplitude amplitude amplitude
(CE-2006) (CE-2006)
CC224HF, CC2200 78 72 67 38 (kN)
17 550 16 200 15 075 8 550 (lb)
CC324HF/384HF, 90 77 75 43 (kN)
CC3200/3800
20 250 17 325 16 875 9 675 (lb)
Propulsion
Speed range 0-12 km/h 0-7.5 mph
Climbing capacity (theoretical)
CC224HF, CC2200 42 %
CC324HF/384HF, 37 %
CC3200/3800
General
Engine
Manufacturer/Model Cummins QSB 3.3 (IIIA/T3)
Deutz TCD 3.6 L04 (IIIB/T4i), (IIIB/T4f)
Power output (SAE J1995), 2200 rpm 60kW (IIIA/T3) 80hp
74kW (IIIA/T3) 99hp
75kW (IIIB/T4i) 100hp
55kW (IIIB/T4f) 75hp
Engine speed
- idling 900 rpm
- loading/unloading 1600 rpm
- work/transport 2 200 rpm
Tier4i / T4f / Stage IIIB engines require the use of Ultra Low Sulphur Diesel (ULSD)
fuel, which has a sulphur content of 15 ppm (parts per million) or less. A higher
sulphur content will cause operating problems and put the useful life of components
at risk, which can lead to engine trouble.
2018-04-25 4812159601_E.pdf
19
Electrical system
Battery 24V (2x12V 74Ah)
Alternator 24V 60A
Fuses See the Electrical system section - fuses
Bulbs (if mounted) Watt Socket

Drive lights, front 75/70 P43t (H4)
Direction lights, front 2 BA9s
Side lights 5 SV8,5
Brake-Position lights 21/5 BAY15d
Direction lights, rear 21 BA15s
License plate light 5 SV8,5
Working lights 70 PK22s (H3)
35 Xenon
Cab lights 10 SV8,5
Hydraulic system
Opening pressure MPa Psi

Drive system 35 5 080
Supply system 2.5 365
Vibration system 19 2 760
Control systems 20 2 900
Brake release 1.8 260
Air Conditioning / Automatic Climate Control

(ACC) (Optional)
The system described in this manual is an AC/ACC
type (Automatic Climate Control). ACC is a system
that maintains the set temperature in the cab, provided
windows and doors are kept closed.
The system contains fluorinated greenhouse gases.
Coolant designation: HFC-134a
Coolant weight when full: 1.350 kg
CO2-equivalent: 1.930 ton
GWP: 1430
4812159601_E.pdf 2018-04-25
20
Tightening torque
Tightening torque in Nm for oiled or dry bolts tightened
with a torque wrench.
Metric coarse screw thread, bright galvanized (fzb):
STRENGTH CLASS:
M- 8.8, Oiled 8.8, Dry 10.9, Oiled 10.9, Dry 12.9, Oiled 12.9, Dry
thread
M6 8,4 9,4 12 13,4 14,6 16,3
M8 21 23 28 32 34 38
M10 40 45 56 62 68 76
M12 70 78 98 110 117 131
M14 110 123 156 174 187 208
M16 169 190 240 270 290 320
M20 330 370 470 520 560 620
M22 446 497 626 699 752 839
M24 570 640 800 900 960 1080
M30 1130 1260 1580 1770 1900 2100
Metric coarse thread, zinc-treated

(Dacromet/GEOMET):
STRENGTH CLASS:
M - thread 10.9, Oiled 10.9, Dry 12.9, Oiled 12.9, Dry
M6 12,0 15,0 14,6 18,3
M8 28 36 34 43
M10 56 70 68 86
M12 98 124 117 147
M14 156 196 187 234
M16 240 304 290 360
M20 470 585 560 698
M22 626 786 752 944
M24 800 1010 960 1215
M30 1580 1990 1900 2360
2018-04-25 4812159601_E.pdf
21
4812159601_E.pdf 2018-04-25
22
Machine description
Machine description
Diesel engine
The machine is equipped with a completely
electronically controlled water-cooled four-cylinder,
turbocharged (WGT) diesel engine with direct injection
(HPCR) and intercooler.
WGT - Waste Gate Turbo
HPCR - High Pressure Common Rail fuel injection
(IIIB/T4i/T4f)
The engine is also equipped with cooled exhaust gas
recirculation (ceGR) and a diesel oxidation catalysator
(DOC) system for exhaust after-treatment.
The engine has also an electronically controlled
variable flow turbo (VFT) and closed crankcase
ventilation.
ceEGR - External Cooled EGR-electronically controlled
DOC - Diesel Oxidation Catalyst
VFT - Variable Flow turbocharger-el. controlled
Electrical system
The machine has the following control units (ECU,
Electronic Control Unit) and electronic units.
• Main ECU (for the machine)
• Diesel engine control unit (ECM)
• I/O board (Control board)
• Display
Propulsion system
The propulsion system is a hydrostatic system
A drive unit (propulsion motor + gear) drives each
drum or wheel pair.
Machines with split drum/s has a drive unit per drum
half and an anti-spin system.
All propulsion motors are connected in parallel, a
hydraulic pump supplies all motors with hydraulic oil.
The speed of the machine is proportional to the angle
of the control lever (the deflection of the
forward/reverse lever regulates the speed). A speed
selector is available as option.
2018-04-25 4812159601_E.pdf
23
Machine description
Brake system
The brake system comprises a service brake,
secondary brake and parking brake. The service brake
system produces retardation of the propulsion system,
i.e. hydrostatic braking.
Secondary/Parking brake
The secondary and parking brake system comprises
sprung disc brakes to each drum, drum half
respectively wheel pair.The disc brakes are
disengaged by hydraulic pressure.
Steering system
The steering system is a hydrostatic system. The
steering wheel is connected to a steering valve that
distributes the flow to the steering cylinders at the
articulated joint. A hydraulic pump supplies the
steering valve with oil.
The steering angle is proportional to the amount the
steering wheel is turned.
In some markets, the machine is also equipped with
an emergency steering system, either manually or
electro-hydraulically.
Vibration system
The vibration system is a hydrostatic system in which
a hydraulic motor drives the eccentric shaft, which
generates the drum's vibrations.
An eccentric shaft in the front-resp. rear drum
generates the the drum's vibrations.
Each eccentric shaft is driven by a hydraulic motor. A
hydraulic pump supplies each hydraulic motor with oil.
High amplitude/low frequency or low amplitude/high
frequency is controlled by the direction of rotation of
the hydraulic motor.
Cab
The cab has a heating and ventilation system, with
defrosters for all windows. The cab can be equipped
with air conditioning (ACC).
Emergency exit
The cab has two emergency exits: the door and the
rear cab window, which can be broken with the
emergency hammer located in the cab.
ROPS
ROPS is the abbreviation for "Roll Over Protective
Structure".
4812159601_E.pdf 2018-04-25
24
Machine description
The cab is approved as a protective cab in accordance

with the ROPS standard.
If any part of the cab's or the ROPS structure's
protective construction displays plastic deformation or
cracks, the cab or the ROPS structure must be
replaced immediately.
Never perform any modifications on the cab or ROPS
structure without first having discussed the
modification with Dynapac's production unit. Dynapac
determines whether the modification could result in the
approval according to the ROPS standard becoming
invalid.
Identification
Product and component plates

1, 2
2 3
4 4
1. Product plate - Product Identification Number (PIN), model/type designation
2. Engine plate - Type description, product and serial numbers
3. Cab/ROPS plate - Certification, product and serial numbers
4. Component plate, drum - Product and serial numbers
2018-04-25 4812159601_E.pdf
25
Machine description
Product identification number on the frame

The machine PIN (Product Identification Number) (1)
is punched on the right edge of the front frame.
Fig. PIN Front frame
Machine plate
The machine type plate (1) is attached to the front left
side of the frame, beside the steering joint.
The plate specifies among other things the
manufacturers name and address, the type of
machine, the PIN, Product Identification Number
1 (serial number), operating weight, engine power and
year of manufacture. (In some cases there are no CE
marking.)
Fig. Operator platform

1. Machine plate
Please state the machine's PIN when ordering

spares.
Explanation of 17PIN serial number

100 00123 V x A 123456 A= Manufacturer
A B C F B= Family/Model
C= Check letter
F= Serial number
4812159601_E.pdf 2018-04-25
26
Machine description
Engine plates
The engine type plates (1) are affixed to the top and
on the right side of the engine.
The plates specify the type of engine, serial number
and the engine specification.
Please specify the engine serial number when
ordering spares. Refer also to the engine manual.
On certain machines there may be an engine plate

along with the machine plate, if the original plate on
the engine is covered with extra
equipment/accessories.
2018-04-25 4812159601_E.pdf
27
Machine description
Decals
Location - decals
10 8 19 7 14
17 16 9 19
20 9 23
7
18
18
1
5 3
14 2 21 4 12 1
22
18 20 20 13
15
1 19
23
7
18
18
3 2 1 11 6
Fig. Location, decals and signs
1. Warning, Crush zone 4700903422 12. Master switch 4700904835
2. Warning, Rotating engine 4700903423 13. Coolant 4700388449
components
3. Warning, Hot surfaces 4700903424 14. Water 4700991657
4. Warning, Brake release 4700904895 15. Hydraulic fluid level 4700272373
5. Warning, Instruction manual 4700903459 16. Hydraulic fluid 4700272372
Biological hydraulic fluid 4700904601/792772
6. Warning, Edge cutter 4700904083 17. Diesel fuel 4700991658*
48121100345**
7. Warning, Locking 4700908229 18. Fixing point 4700382751
4812125363
8. Warning, Toxic gas 4700904165 19. Hoisting plate 4700904870
9. Warning, Starting gas 4700791642 20. Lifting point 4700357587
10. Handbook compartment 4700903425 21. Sound effect level 4700791276/77
11. Battery voltage 4700393959 22. Emergency exit 4700903590
23. Tire pressure (Combi) 4700355983
*) IIIA/T3 24 Fuel with a low sulphur content 4811000344**
**) IIIB/T4i/T4f
4812159601_E.pdf 2018-04-25
28
Machine description
Safety decals
Always make sure that all safety decals are completely
legible, and remove dirt or order new decals if they
have become illegible. Use the part number specified
on each decal.
4700903422
Warning - Crush zone, articulation/drum.
Maintain a safe distance from the crush zone.
(Two crush zones on machines fitted with pivotal steering)
4700903423
Warning - Rotating engine components.
Keep your hands at a safe distance.
4700903424
Warning - Hot surfaces in the engine compartment.
Keep your hands at a safe distance.
4700904895
Warning - Brake disengagement
Study the towing chapter before disengaging the
brakes.
Danger of being crushed.
4700903459
Warning - Instruction manual
The operator must read the safety, operation and
maintenance instructions before operating the
machine.
4700904083
Warning - Edge cutter (option)
Warning of rotating parts.
Maintain a safe distance from the crush zone.
2018-04-25 4812159601_E.pdf
29
Machine description
4700908229
Warning - Risk of crushing
The articulation must be locked when lifting.
Read the instruction manual.
4812125363
Warning - Locking
The articulation must be locked during transport
and lifting,
but be open during operation.
4700904165
Warning - Toxic gas (option, ACC)
4700791642
Warning - Starting gas
Starting gas is not to be used.
4812159601_E.pdf 2018-04-25
30
Machine description
Info decals
Manual compartment Battery voltage Master switch
Coolant Water Hydraulic fluid level
Hydraulic fluid Biological hydraulic fluid Diesel fuel
Bio-hydraulic fluid PANOLIN Fuel with low sulphur content (IIIB/T4i)
Fixing point Hoisting plate Lift point
Sound effect level
Tire pressure(combi) Emergency exit
2018-04-25 4812159601_E.pdf
31
Machine description
Instruments/Controls
Control panel and controls

33
7 8 9 34
14 6
2
10 22
15 23 28/30/35
11
24 29/31
12 20 31
13 25 32
21
26
16
17 27 1
19 30
18 36
Fig. Control panel
37
1 Ignition switch 13 Vibration rear drum 25 Parking brake
2 Forward & Reverse lever 14 Work mode (Off-set and 26 * Hazard lights
vibration permitted plus soft
starting and stopping enabled)
15 CG – front drum steering only 27 * Rotating beacon
16 Manual sprinkler 28 * Gravel spreader (not for combi)
17 Increase sprinkler (timer) 29 Gear position switch
6 Button set 18 Auto sprinkler (AWC) 30 * Edge cutter, Up/Down
7 Central warning indicator 19 Decrease sprinkler (timer) 31 * Edge cutter, sprinkling
8 * Direction indicators 20 * Working light 32 * Drum edge lights
9 * Full beam indicator 21 Horn 33 Display
10 High amplitud 22 Emergency stop 34 Function buttons (5 pcs.)
11 Vibration front drum 23 Speed limiter 35 Sprinkling, emulsion tank
(combi)
12 Auto vibration control (AVC) 24 Rpm switch, diesel engine 36 Service socket
37 Height adjustment, control
panel
* Optional
4812159601_E.pdf 2018-04-25
32
Machine description
Functions
1. Direction indicators
2. Driving lights
3. Full/Dipped beam
4. Parking lights
5. Horn
Figure. Steering column switch

(optional)
Function descriptions
No Designation Symbol Function

1 Ignition key The electric circuit is broken.
All instruments and electric controls are supplied with power.
Starter motor activation.
To start: Turn ignition key to the right until the display

LIGHTS UP, and wait until the displayed roller GOES OFF
and changes to the status image.
2 Forward/Reverse lever NOTE: The lever must be in neutral to start the machine. The
engine will not start if the lever is in any other position.
The direction and speed are controlled with the
forward/reverse lever. Moving the lever forward moves the
roller forward, and moving it back moves the roller back.
The speed of the roller is proportional to the distance of the
lever from neutral. The further the lever is from neutral, the
higher the speed.
6 Button set
7 Central warning indication General fault indication. See display (33) for fault description.
8 Direction indicators Shows direction indicators activated (Activated via the

steering column switch).
9 Main beam indicator Shows main beam activated (Activated via the steering
column switch).
10 Amplitude selector, high Activation produces high amplitude. (Low amplitude is the
amplitude basic mode if the button is not activated.)
11 Vibration, front drum Activation of vibration on front drum.

If Working mode (14) is not activated, there will be no vibration
NEVER activate the switch on the drum.
when the switch (4) is
activated.
12 Automatic vibration control By activating the vibrations will be switched ON and OFF
(AVC) automatically when the F/R lever is moved from neutral and
the roller reaches a preset speed.
2018-04-25 4812159601_E.pdf
33
Machine description

13 Vibration rear drum Activation of vibration on rear drum.
If Working mode (14) is not activated, there will be no vibration
NEVERactivate the switch on the drum.
when the switch (4) is
activated.
14 Work mode (Off-set and Activates working mode, which makes it possible to use
vibration permitted plus soft vibration and offset (option), with soft start and stop activated.
starting and stopping The roller always starts in transport mode.
enabled)
(15) Front drum steering only (CG) Valid for pivot machines only (CG). By activating steering on
front drum only.
16 Manual sprinkler Continuous sprinkling on both drums.
17 Increasing sprinkling (timer) Each push on the button gives higher sprinkling water volume
on drums.
18 Automatic sprinkling By activating the sprinkling water will engage and disengage
automatically when the F/R lever is moved from neutral.
19 Decreasing sprinkling (timer) Each push on the button gives lower sprinkling water volume
on drums.
20 Working lights By activating the working lights will turn ON.
21 Horn Press to sound the horn.
22 Emergency stop Brakes the roller and switches off the engine. The power
supply goes off.
NOTE: The emergency stop must be deactivated when
starting the machine.
23 Speed limiter Limitation of the machine's max. speed (max.speed is
obtained with full deflection of the F/R lever). Set the knob to
the required position and read the speed on the display (30).
24 Rpm switch, diesel engine Three-position switch for idling (LO), intermediate speed (MID)
and working speed (HI).
NOTE: The lever must be in neutral (LO) when starting the
machine. The engine also runs at low speed when stationary,
more than approx. 10 seconds if the F&R lever is in neutral.
If the F&R lever is moved out of neutral the speed will
increase to the set speed again. If the machine has a fuel
optimization system, MID is replaced by ECO (and the switch
is green).
4812159601_E.pdf 2018-04-25
34
Machine description

25 Parking brake When pressed, the parking brake is activated.
To release the brakes, slide the red part back (towards you)
and change the position of the lever.
NOTE: When starting the machine, the parking brake must
be activated.
To activate the brakes, press the top of the switch to change

the position of the lever.
To release the brakes, press down the red part at the same
time as the switch and change the position of the lever.
NOTE: When starting the machine, the parking brake must
be activated.
26 Hazard warning lights Activate the hazard warning light by depressing the button.
27 Rotating beacon Activate the rotating beacon by depressing the button.
28 Gravel spreader Activating the gravel spreader. Manual/Automatic spreading.

(CC224-324, CC2200-3200)
29 Gear position switch Activates the three different gear positions: (1), (2), (3). The
current gear position is shown in the display by means of the
following figures.
Position 1: Used for maximum hill-climbing capacity during

vibratory compaction
Position 2: Normal position
Position 3: Used for maximum transport speed or for high

speed during smooth rolling without vibration
2018-04-25 4812159601_E.pdf
35
Machine description

30 Edge press/cutter, UP/DOWN The edge cutter can be moved up and down when the
machine is in the operating position. The edge cutter can only
be moved up when the machine is in transport position.
Pressing on the lower edge moves the edge cutter down.
Pressing on the upper edge moves the edge cutter up.
31 Edge press/cutter, sprinkling Activate edge press/cutter sprinkling by depressing the switch.
32 Drum edge lights Activate the drum edge lights by depressing the switch.
35 Sprinkler combi wheel Activate the emulsion sprinkler for combi wheels by
depressing the switch.
36 Service socket Diagnostic socket.

Gateway is connected here to read the CAN-Open system.
4812159601_E.pdf 2018-04-25
36
Machine description
Forward & Reverse lever

1 Vibration on/off 5 * Edge cutter, Up
5 2 Panic sprinkler (ON as long as 6 * Edge cutter, Down
button depressed)
3 4 3 * Offset left
4 * Offset right
* Optional
1 2
Fig. Forward & Reverse lever

1 Vibration on/off First push will start vibrations, second push will stop
vibrations.
2 Panic sprinkling Panic sprinkling of both drums. Push the button to get full flow
on sprinkler pump.
3, 4 Offset left/right The left button moves the rear drum to the left, the right button
to the right.
Always stop in neutral and to switch to the other side press
once again. Steady light in working mode. (flashes in offset)
5, 6 Edge press/cutter, UP/DOWN The edge cutter can be moved up and down when the
2018-04-25 4812159601_E.pdf
37
Machine description
Forward & Reverse lever

1 Vibration on/off 5 * Edge cutter, Up
3 2 Panic sprinkler (ON as long as 6
5 * Edge cutter, Down
button depressed)
4 3 * Offset left
4 * Offset right
6
* Optional
1 2
Fig. Forward & Reverse lever

1 Vibration on/off First push will start vibrations, second push will stop
vibrations.
2 Panic sprinkling Panic sprinkling of both drums. Push the button to get full flow
on sprinkler pump.
3, 4 Offset left/right The left button moves the rear drum to the left, the right button
to the right.
Always stop in neutral and to switch to the other side press
once again. Steady light in working mode. (flashes in offset)
5, 6 Edge press/cutter, UP/DOWN The edge cutter can be moved up and down when the
Display explanations
When the ignition key is activated to position I, a start

screen is visible in display. This is shown for a few
seconds and then switches over to the status screen.
Fig. Start screen
4812159601_E.pdf 2018-04-25
38
Machine description
A status screen provides information on the fuel level,

water level in the sprinkler tank, machine hours and
voltage level. Fuel and water levels are specified in
per cent (%).
This screen is active until the Diesel engine is started
or an active screen choice is made via the function
buttons below the display.
Fig. Status screen
If the engine is started before any active screen choice

is made the display will switch over to main screen.
This screen gives an overview and is kept during work:
- The speed is shown in the middle of the screen.
- The engine speed, vibration frequencies for forward
and reverse (Option), strokes/meter - Impactometer
Fig. Main screen/Working screen (Option), and asphalt temperature (Option), are shown
in the corner.
A menu field is shown by pressing one of the menu

select buttons. The field is visible for a short while, if
no selection is made the field fades out. Menu field will
appear again upon pressing either one of the selection
buttons (1).
Fig. Main screen/Working screen with

menu selection buttons (1)
Example of menu field.
2018-04-25 4812159601_E.pdf
39
Machine description
Scroll/Selection buttons to choose

between available functions.
Alarm log button to display engine and
machine alarms.
Settings/Button select menu, which opens
the main menu. Settings can be changed
in the main menu.
Exit/Return button returns 1 step at once.
Pressing the button (approx. 2 sec.)
displays the main menu again.
The temperature screen shows the temperature of the

engine (top of display) and hydraulic fluid (bottom of
display). The values are shown in Celsius or
Fahrenheit, depending on the choice of unit system.
A menu for the asphalt temperature and Impactometer

value can also be shown when an accessory asphalt
temperature gauge and/or Impactometer is installed
on the machine. Further information on these
Fig. Temperature screen accessories are given in the Accessory Manuals.
Fig. Asphalt temperature/Impactometer

screen
4812159601_E.pdf 2018-04-25
40
Machine description
When an engine alarm is activated, the alarm is shown

on the display.
The engine alarm is sent out from the engine ECM,
which handles the monitoring of the engine functions.
The message, which consists of an SPN and FMI
code, can be interpreted via the engine supplier error
code list.
The alarm message shown is acknowledged by
pressing the "OK" button on the display.
When a machine alarm is activated the alarm is shown

on the display, plus a warning text that describes the
alarm.
The alarm message shown is acknowledged by
pressing the "OK" button on the display.
2018-04-25 4812159601_E.pdf
41
Machine description
Machine alarm
Symbol Designation Function

Warning symbol, hydraulic fluid filter If the symbol is shown when the diesel engine is running at
full speed, the hydraulic fluid filter must be changed.
Warning symbol, clogged air filter If this symbol is shown when the engine is running at full
speed, the air filter must be checked/replaced.
Warning symbol, battery charging If the symbol is shown when the engine is running, then
the alternator is not charging.
Switch off the engine and locate the fault.
Warning symbol, engine temperature If this symbol is shown, the engine is too hot. Stop the
engine immediately and locate the fault.
Refer also to the engine manual.
Warning symbol, hydraulic fluid If this symbol is shown, the hydraulic fluid is too hot.
temperature Do not drive the roller; allow the fluid to cool by running the
engine on idle, and then locate the fault.
Warning symbol, low fuel level Less than 10% of the fuel is left if this symbol is shown.
Warning symbol, low sprinkler water If this symbol is shown, there is less than 10% of the
level sprinkler water left in the main tank.
Warning symbol, low oil pressure, If this symbol is shown, the engine's oil pressure is too low.
diesel engine Switch off the engine immediately.
Warning symbol, low coolant level If this symbol is shown, fill with coolant/glycol and search
for leaks.
Warning symbol, water in the fuel If this symbol is shown, the engine must be stopped and
the fuel pre-filter drained of water.
4812159601_E.pdf 2018-04-25
42
Machine description
Alarms received are saved/logged and can be seen by

selecting Display alarms.
Selection of Display alarms.
"ENGINE ALARM"
Saved/Logged engine alarms.
"MACHINE ALARM"
Saved/Logged machine alarms. These alarms come
from the other systems on the machine.
"MAIN MENU"
In the main menu it is also possible to change some
user and machine settings, access the service menu
for calibration purposes (special service personnel
only, requires pin code), and to see the version of
installed software.
2018-04-25 4812159601_E.pdf
43
Machine description
"USER SETTINGS"
Users can change the light settings, choose between
the Metric or Imperial system, and set warning sounds
On/Off.
Adjustment of the light and contrast settings on the

display, including brightness of the panel light.
4812159601_E.pdf 2018-04-25
44
Machine description
"MACHINE SETTINGS"
The selection "Sprinkler Pump: 1 & 2" is in machine

settings.
If the machine is fitted with double sprinkler pumps
(Option) this is the menu in which the selection is
made for which of the sprinkler pumps are to be
activated to water the drum(s).
If the machine is fitted with accessories, e.g. a Chip

spreader, the settings for these can also be changed.
"WORKMODE SETTINGS"
This section is protected by Pin Code
There are 3 different modes that can be seleted in the
machine's workmode. (Soft, Medium, Hard).
The machine alerts at startup when the setting is in
Soft Mode.
"SERVICE MENU"
The service menu is also accessible via the main
menu for adjustments.
2018-04-25 4812159601_E.pdf
45
Machine description
"ADJUSTMENTS"
"TESTMODES" - Installation personnel only, requires

pin code.
"CALIBRATION" - service personnel only, requires

password.
"EDC Calibration" used to calibrate the joystick and
speed potentiometer.
"TX Program" only used to change software in the
display and requires special equipment and know-how.
"EDC CALIBRATION"
To calibrate, move the joystick fully forward (F) and
press in both black buttons on the top of the joystick.
(See also manual W3025)
Continue in the same way with the other positions for
the joystick (N), (R) and the speed potentiometer.
Press the disk button to save the values.
4812159601_E.pdf 2018-04-25
46
Machine description
"ABOUT"
It is also possible to see the version of the installed
software.
Operator help when starting

When trying to start the machine without having set
one, two or three of the conditions required to start
machine, the missing conditions are shown in the
display.
The missing conditions must be set before it is
possible to start the machine.
Conditions that must be set:

- Activated P-brake
- Selector lever in neutral
- Speed selector for diesel engine in low (Low = idling)
(not all models)
Operator help Workmode

When attempting to activate
- Vibration
- Offset control (Option)
- Edge cutter/compactor (Option)
with the machine in Transport mode the display will
show "Workmode" for a few seconds.
To activate the above functions it is necessary to

make sure that the machine's Workmode is activated.
2018-04-25 4812159601_E.pdf
47
Machine description
Instruments and controls, cab

Radio/CD
14
4
1 2 3
7
Fig. Cab roof, front
5 6
15
Fig. Right rear cab post
4812159601_E.pdf 2018-04-25
48
Machine description
Function description of instruments and

controls in the cab

1 Heater control Turn to the right to increase heating.
Turn to the left to reduce heating.
2 Ventilation fan, switch In the left position, the fan is off.
Turning the knob to the right increases the
volume of air entering the cab.
3 Air conditioning, switch Starts and stops the air conditioning.
4 Cab air recirculation, switch Pressing the top opens the air damper so that
fresh air comes into the cab.
Pressing the bottom closes the damper so that
the air recirculates inside the cab.
5 Front wiper, switch Press to operate the front screen wiper.
6 Front and rear window screen Press the upper edge to activate the front screen
washers, switch washers.
Press the lower edge to activate the rear screen
washers.
7 Rear wiper, switch Press to operate the rear screen wiper.
8 Fuse box Contains fuses for the electrical system in the

cab.
14 Defroster nozzle Turn the nozzle to direct the flow of air.
15 Hammer for emergency exit To escape from the cab in an emergency,
release the hammer and break the opening
windows on the right-hand side.
2018-04-25 4812159601_E.pdf
49
Machine description
Using the cab controls.

Defroster
To quickly remove ice or mist, make sure that only the
front and rear air nozzles are open.
Turn the heater and fan dial (1 and 2) to max.
Adjust the nozzle so that it blows on the window to be
de-iced, or to remove mist.
Heat
If the cab is cold, open the lower nozzle on the front
columns and the middle nozzles just over the controls
for the heater and fan.
Turn to max heat and max fan speed.
When the required temperature has been reached,
open the other nozzles and if necessary turn down the
heat and fan speed.
1 2 3 4
AC/ACC
NOTE: When using AC/ACC all the windows must be
closed for the system to work efficiently.
To quickly reduce the temperature in the cab, adjust

the following settings on the control panel.
Turn on AC/ACC (3) and set the fresh air (4) in the
lower position to switch off the fresh air valve.
Set the heater control (1) to minimum and turn up the
fan speed (2). Keep only the front middle nozzles in
the ceiling open.
When the temperature has dropped to a comfortable
level, adjust the required temperature on the heater
control (1) and reduce the fan speed (2).
Now open the remaining nozzles in the roof to achieve
a comfortable temperature in the cab.
Reset the fresh air button (4) to the upper position for
fresh air.
4812159601_E.pdf 2018-04-25
50
Machine description
Electrical system (version 1)

The machine's main switchbox (1) is located on the
rear of the operator platform. There is a plastic cover
over the distribution box and fuses.
On the plastic cover there is a 24V socket.
3
1
Fig. Main electrical central
1. Control unit (ECU)
2. Fuses
3. Main relay
Fuse boxes in main switchbox
The figure shows the position of the fuses.

The table below gives fuse amperage and function. All
fuses are flat pin fuses, type C (medium).
Fig. Fuse box

Fuse box (F1)
1. Main relay (F1.1) 5A 5. Power group 3, Main ECU (F1.5) 20A
2. Supply, Main ECU, I/O unit, Display 5A 6. Power group 4, Main ECU (F1.6) 20A
(F1.2)
3. Power group 1, Main ECU (F1.3) 10A 7. 24V outlet, Lighting for tachograph (F1.7) 10A
4. Power group 2, Main ECU (F1.4) 10A 8. Accessory ECU (F1.8) 20A
Fuse box (F2)

1. 5.
2. DCA Asphalt (F2.2) 10A 6. Process lightning (F2.6) 15A
3. 7. Driving lights (turn signals) (F2.7) 7.5A
4. 8. Driving lights (main.) (F2.8) 10A
2018-04-25 4812159601_E.pdf
51
Machine description
Electrical system (version 2)

3 4 5 6 1
The machine's main switchbox (1) is located on the
rear of the operator platform. There is a plastic cover
over the distribution box and fuses.
On the plastic cover there is a 24V socket and a 12V
socket (optional).
2
Fig. Main switchbox
1.Control unit (ECU) (A7)
2. Fuse card (A6)
3. Main relay (K2)
4. Relay, drum edge lights (K8)
5. Relay, direction indicators (K9)
6. Relay, driving lights (K10)
Fuse card in main switchbox

The figure shows the position of the fuses.
fuses are flat pin fuses, type C (medium).
Fig. Fuse card.
Fuse card (A6)

F1 Main relay (K2), 24V outlet engine 10A F9 Sprinkler pump 1 10A
compartment(X97)
F2 Supply, Main ECU (A7), I/O unit (A12), Display 5A F10 Sprinkler pump 2 10A
(A13), Diagnostic socket engine (X22)*
F3 Power group 1, Main ECU, Power for frequency 10A F11 24/12V converter (12V socket cab) 10A
sensor
F4 Power group 2, Main ECU, Terminal 15, Control 10A F12 GPS receiver (DCA) (A26) 5A
panel
F5 Power group 3, Main ECU 20A F13 Process lighting (Drum edge lighting) 15A
F6 Power group 4, Main ECU 20A F14 DCA computer (PC) (A25) 10A
F7 24V outlet driver seat (X96), Lighting tachograph 10A F15 Direction indicators 7.5A
F8 Power for speed sensor, Fuel pump (M13)* 10A F16 Driving lights (Pos., Full/Dipped beam) 10A
*) Only valid for CC224-384, CC2200-3800 with
Deutz engine.
4812159601_E.pdf 2018-04-25
52
Machine description
Power in engine compartment/battery

compartment
The fuses in the engine compartment are located
alongside the master switch.
2
The roller is equipped with 24 V electrical system and

an AC alternator.
1
Connect the correct polarities (ground) to the

battery. The cable between the battery and the
Fig. Battery bay alternator must not be disconnected when the
1. Master switch engine is running.
2. Main fuse panel
Main fuse panel (Cummins)

6
4 The main fuse panel is located behind the left engine
compartment door.
3 The fuses are placed in the order shown below,
2 starting by the plate.
F13 Engine ECU (30A)
5 1 F10 Main fuse (50A)

F11 Cab (50A)
Fig. Main fuse panel

1. Master switch
2. Preheating relay (100A)
3. Fuse (F20) (125A)
4. Starter relay (50A)
5. Fuses (F13, F10, F11)
6. Power socket 24V
2018-04-25 4812159601_E.pdf
53
Machine description
Main fuse panel (Deutz)

5
4 The main fuse panel is located behind the left engine

compartment door.
3
1
Fig. Main fuse panel

1. Master switch
2. Preheating relay (100A)
3. Starter relay
4. Power socket 24V
5. Fuse box (F4)
Fuse box at master switch (Deutz)
1 2 The figure shows the position of the fuses.

fuses are flat pin fuses, type E (high).
3 4
F4 Fuse box
F4.1. Main fuse 50A
F4.2. Cab 50A
Fig. Fuse box, master switch F4.3. Preheating relay 100A
F4.4. Diesel engine ECU 30A
4812159601_E.pdf 2018-04-25
54
Machine description
Fuses in cab
The electrical system in the cab has a separate fuse
box located on the front right side of the cab roof.
Fig. Cab roof fuse box (F7) The figure shows fuse amperage and function.
All fuses are flat pin fuses.
1. Interior lighting 10A
2. CD/Radio 10A
3. AC condensor 15A
4. Cab fan 15A
5. Windscreen wiper/washers, 10A
front
6. Windscreen wiper/washers, 10A
rear
7. Reserve
8. Reserve
2018-04-25 4812159601_E.pdf
55
Machine description
4812159601_E.pdf 2018-04-25
56
Operation
Operation
Before starting
Master switch - Switching on

Remember to carry out daily maintenance. Refer to
the maintenance instructions.
The master switch is located in the engine
compartment. Turn the key (1) to the on position. The
entire roller is now supplied with power.
1 If the main battery/master switch is covered, the
engine hood must be unlocked during operation,
to be able to reach the switch in an emergency.
Figure. Engine door, left

1. Master switch
Control panel, adjustments

The control unit has three adjustment options,
transverse travel, rotation and steering column angle.
3
2
For transverse travel, raise the inner lever (1), which
releases the catch.
For rotation, lift the outer lever (2).
Ensure that the control unit locks in position before
operating the machine.
1
Release locking lever (3) to adjust the steering
column. Lock in the new position.
Fig. Operator position
1. Locking lever - transverse travel To adjust the operator's seat, see the section for
2. Locking lever - rotation basic/comfort seat.
3. Locking lever - steering column Adjust all settings when the machine is stationary.
angle
Always ensure that the seat is in locked position

before operating the roller.
2018-04-25 4812159601_E.pdf
57
Operation
Operator's seat - Adjustment

Adjust the operator’s seat so that the position is
comfortable and so that the controls are within easy
reach.
2
1
The seat can be adjusted as follows.
4
- Length adjustment (1)
3
- Weight adjustment (2)
Fig. Operator's seat - Back support angle (3)
1. Lock pack- Length adjustment
2. Weight adjustment
3. Back support angle
4. Seat belt Always make sure that the seat is secure before
beginning operation.
Do not forget to use the seatbelt (4).
Belt reminder
The machine can be equipped with seat belt with belt
reminder.
Unless the seat belt is used, a warning image appear
in the display and a warning buzzer sounds to alert the
driver to use the seat belt.
4812159601_E.pdf 2018-04-25
58
Operation
Operator's seat, comfort - Adjustments

6
Adjust the operator's seat so that the position is
comfortable and so that the controls are within easy
reach.
3 The seat can be adjusted as follows:
- Length adjustment (1)
- Height adjustment (2)
2 5 - Seat-cushion inclination (3)
- Backrest inclination (4)
- Armrest inclination (5)
4 - Lumbar support adjustment (6)
1
Fig. Operator’s seat Always ensure that the seat is locked in position
1. Lever - length adjustment before operating the roller.
2. Wheel - height adjustment
3. Wheel - seat cushion inclination
4. Wheel - backrest inclination
5. Wheel - armrest inclination
6. Wheel - lumbar support adjustment
Parking brake
Ensure that the parking brake (1) is definitely
switched on.
Brake is always activated in Neutral. (automatic 2 sec.)

The parking brake must be activated to start the
Fig. Control panel
1. Parking brake machine!
2018-04-25 4812159601_E.pdf
59
Operation
Display - Control
2 Sit down for all operations.
Turn the ignition key (1) to position I, the start screen
will be shown in display.
Fig. Control panel

1. Ignition key
2. Status screen
3 4 Check that the voltmeter (6) shows at least 24 volts

and the levels for fuel (3) and water (4) indicates a
percentage value.
The hourmeter (5) registers and shows the total
number of hours the engine has run.
5 6
Fig. Status screen

3. Fuel level
4. Water level
5. Hour meter
6. Voltmeter
4812159601_E.pdf 2018-04-25
60
Operation
Interlock
The roller is equipped with Interlock.
The diesel engine with switch off after 7 seconds if the
operator gets off the seat when going
forwards/backwards.
If the control is in neutral when the operator stands up
a buzzer will go on until the parking brake is activated.
If the parking brake is activated, the diesel engine will
not stop if the forward/reverse lever is moved out of
neutral.
The diesel engine will switch off immediately if for any
reason the forward/reverse lever is moved out of
neutral when the operator is not sitting down and the
parking brake has not been activated.
Sit down for all operations!
2018-04-25 4812159601_E.pdf
61
Operation
Operator position
If a ROPS (Roll Over Protective Structure) or a cab is
fitted to the roller, always wear the seat belt (1)
provided and wear a protective helmet.
2 2
3
Replace the seat belt (1) if it shows signs of
wear or has been subjected to high levels of
3 force.
1
The safety rails (2) around the cab are adjustable
5 4
in the inner and the outer positions. Pull in the
rails when driving close to walls or other
Fig. Operator position obstacles, and when transporting the machine.
1. Seat belt
2. Safety railing
3. Locking knob
4. Rubber element
5. Anti-slip Release the locking knob (3), set the the railings in the
required position and relock in position.
Check that the rubber elements (4) on the
platform are intact. Worn elements will reduce
comfort.
Ensure that the anti-slip (5) on the platform is in

good condition. Replace where anti-slip friction is
poor.
If the machine is fitted with a cab, make sure that

the door is closed when in motion.
View
Before starting, make sure that the view forwards and
backwards is unobstructed.
All cab windows should be clean and the rear view
mirrors should be correctly adjusted.
Fig. View
4812159601_E.pdf 2018-04-25
62
Operation
Starting
Starting the engine

Make sure that the emergency stop is OFF and the
parking brake ON.
1 Set the forward/reverse lever (1) in neutral position,
and set the speed selector (2) in the idling position
(LO) or (ECO) if that option is installed on the machine.
The diesel engine cannot be started in any other
2 position of the controls.
3
Turn the ignition key (3) right to position I and wait for
the grid heater symbol to disappear from the display.
Fig. Control panel Then engage the starter by turning it full right. Release
1. F/R lever back to I as soon as the engine starts.
2. Rpm switch
3. Ignition key
While preheating of diesel engine is running the
symbol grid heater is shown in the center of the
display.
Do not run the starter motor for too long (max. 30
seconds). If the engine will not start, wait a
minute before trying again.
At the start of the diesel engine when the ambient

temperature is below +10 ° C (50 ° F), it must be
warmed up at idle (low speed) until the hydraulic oil
temperature exceeds +10 ° C (50 ° F).
Ensue that there is good ventilation (air extraction)
if the engine is run indoors. Risk of carbon
monoxide poisoning.
Check during warming up of the engine that fuel and

water levels are shown correctly and that the voltage
is at least 24V.
Figure. Display - Status image
2018-04-25 4812159601_E.pdf
63
Operation
When starting and driving a machine that is cold,

remember that the hydraulic fluid is also cold and
that braking distances can be longer than normal
until the machine reaches the working temperature.
The machine always starts in the Transport

position, without it being possible to use off-set,
vibration or sprinkling.
If the machine and drums are in off-set mode,

switch to work mode and reset before loading the
machine on a truck. This is indicated by a warning
in the display.
Display when activating choice via the button

set.
The parking symbol is shown when the parking brake is

activated.
= Operating position, off-set, vibration and sprinkling

possible. The symbol flashes in off-set mode, in neutral
(reset off-set) the symbol shines constantly.
= Automatic Water Control (AWC), sprinkling is

activated when the F/R lever is outside neutral.
= High amplitude
= Vibration on front and rear drum.
= Automatic Vibration Control (AVC),

vibration is activated when the F/R lever is
outside neutral.
= Display of alarm, see table for information.
4812159601_E.pdf 2018-04-25
64
Operation
Alarm descriptions
Symbol Designation Function

Warning lamp, hydraulic filter If the lamp comes on while the engine is running at full
speed, the hydraulic filter must be changed.
Warning lamp, air filter If the lamp comes on while the engine is running at full
speed, the air filter must be cleaned or replaced.
Warning lamp, battery charging If the lamp comes on while the engine is running, the
alternator is not charging.
Stop the engine and locate the fault.
Warning light, engine temperature If the lamp comes on, the engine is too hot. Stop the
engine immediately and locate the fault.
Refer also to the engine manual.
Warning lamp, hydraulic fluid If the lamp comes on, the hydraulic fluid is too hot.
temperature Do not drive the roller. Cool the fluid by allowing the engine
to idle and locate the fault.
Driving
Operating the roller

Under no circumstances is the machine to be
3 operated from the ground. The operator must be
seated inside the machine during all operation.
1
2 Activate working speed (1) = HI or ECO if available.

In ECO, the machine automatically regulates the
engine speed according to requirements.
If the machine is only to be transported, MID or ECO
Fig. Control panel should be selected instead.
1. Rpm switch
2. Parking brake
3. Forward/Reverse lever
Check that the steering is working correctly by turning
the steering wheel once to the right and once to the
left while the roller is stationary.
2018-04-25 4812159601_E.pdf
65
Operation
When compacting asphalt, remember to turn on the

4 sprinkler system (4) or (5).
Make sure that the area in front of and behind the
roller is clear.
Release the parking brake (2).

5
4. Manual sprinkling
5. Auto sprinkling (AWC)
Machine with gear change in separate

spring-return switch (gear position switch)
Switch (1) is a spring-return gear position switch,
2 where gear changing take place by stepping through
the three different gear positions: Position 1, Position 2
and Position 3.
• Position 1: Used for maximum hill-climbing capacity
during vibratory compaction
1 • Position 2: Normal position
• Position 3: Used for maximum transport speed or for high
speed during smooth rolling without vibration
Fig. Control panel
1. Gear position switch
Fig. The display shows the selection in

the middle (position 1, 2 or 3)
4812159601_E.pdf 2018-04-25
66
Operation
The machine's gear position is shown in the center of

the speedometer; select the gear/speed for the task.
The machine does not need to be stopped to change
gear position.
Max. speed
= Position 1 6 km/h 3.8 mph
= Position 2 8 km/h 5 mph
= Position 3 12 km/h 7.5 mph
Carefully move the forward/reverse lever (2) forwards

or backwards, depending on which direction of travel
is required.
The speed increases as the lever is moved away from
the neutral position.
Interlock/Emergency stop/Parking brake -

Check
The interlock, emergency stop and parking brake must

be checked daily before operating. A function check of
the interlock and emergency stop requires a restart.
The interlock function is checked by the operator

standing up from the seat when the roller is moving
very slowly forwards/backwards. (Check in both
directions). Hold the steering wheel firmly and brace
yourself for a sudden stop. A buzzer goes on and after
7 seconds the engine switches off and the brakes are
activated.
Check the function of the emergency stop by pressing

the emergency stop button when the roller is moving
slowly forwards/backwards. (Check in both
directions). Hold the steering wheel firmly and brace
yourself for a sudden stop. The engine switches off
and the brakes are activated.
Check the function of the parking brake by activating

the parking brake when the roller is moving very
slowly forwards/backwards. (Check in both
directions). Hold the steering wheel and brace yourself
for a sudden stop when the brakes are activated. The
engine does not switch off.
2018-04-25 4812159601_E.pdf
67
Operation
Pivotal steering (Optional)

The machine must be in the operating position to
activate the pivotal steering. Use the two front buttons
(1) on the forward/reverse lever to operate the pivotal
1 steering.
To reset the rear drum to neutral, adjust the buttons
(1) until the display (2) shows that the machine has
aligned the drums.
The symbol for Work mode shines continuously in
neutral (drums in line)
Fig. F/R lever
1. Offset steering If fault indication on the display is shown or if the
buzzer sounds, stop immediately the roller in a safe
place and shut off the Diesel engine. Check the cause
for failure and remedy, see also maintenance manual,
2 trouble shooting guide or engine manual.
Figure. Display
Edge cutting (Optional)

The machine must be running to activate the edge
cutter/compactor.
1 When the machine is in the operating position and the

2 switch (1) is pressed at the bottom, the edge
cutter/compactor is lowered to the asphalt surface by
means of a hydraulic cylinder. To reset the edge
cutter/compactor in its original position, press the top
of the switch to lift the edge cutter/compactor.
The edge cutter/compactor can also be lifted if the
machine is in transport position.
Figure. Switch
1. Edge cutter/compactor Up/Down A bypass valve prevents the hydraulic system being
2. Sprinkler, edge cutter/compactor overloaded.
There is a separate sprinkler system which the
operator should use to avoid asphalt sticking to the
edge cutter/compactor. The system is operated with a
switch (2). The water is drawn from the main water
tank, which is also used for the normal sprinkler
system.
4812159601_E.pdf 2018-04-25
68
Operation
The operator can choose between two tools, the edge

cutter or edge compactor. The edge cutter (1) in the
figure is shown in the operating position. The edge
compactor (1) can easily be replaced with the edge
cutter by releasing the bolted joint (3).
4
3
1 3 2
Fig. Changing the tool
1. Edge compactor
2. Edge cutter
3. Bolted joint
4. Holder for cutter/compactor wheel
Vibration
Manual/Automatic vibration
4 Activate the button for the Working mode (4).
Manual or automatic vibration activation/deactivation is
1 selected using button (1).
2 In the manual position the operator has to activate the
vibration via the bottom left switch on the
forward/reverse lever (2).
3
In automatic mode (AVC), vibration is activated when
the speed is ≥ x km/h (... mph) and turns off at a speed
of x km/h (...mph)
Fig. Control panel Activation of vibration for the first time, as well as
1. Automatic vibration control (AVC) disconnection of automatic vibration, are performed
2. Switch, vibration On/Off
3. Rpm switch with the switch (2) on the forward/reverse lever.
4. Working mode
Note that vibration can only be activated when the

working mode (4) is activated, and when the Rpm
switch (3) for the engine is in high (HI) or Eco
mode (ECO). After 10 seconds in neutral, the
vibration is switched off and the machine drops to
low speed.
2018-04-25 4812159601_E.pdf
69
Operation
Manual vibration - Switching on

Never activate vibration when the roller is
stationary. This can damage both the surface and
the machine.
1
Engage and disengage vibration using the switch (1)
on the front of the forward/reverse lever.
Always switch off vibration before the roller comes to a
standstill.
Fig. F/R lever When compacting thin layers of asphalt up to approx.

1. Vibration ON/OFF 50 mm (2 inches) thick, the best results are achived
with low amplitude/high frequency.
Amplitude/frequency - Changeover
The amplitude setting must not be change when
vibration is in operation
1 Switch the vibration off and wait until vibration
stops before changing amplitude.
2
By pressing button (1) high amplitude is achieved.
3
The buttons (2) and (3) are used to get vibrations
either on front or rear drum or on both.
- (2) vibration on front drum.
Fig. Control panel
1. High amplitude - (3) vibration on rear drum.
2. Vibration fron drum
3. Vibration rear drum
Braking
Normal braking
Press the switch (1) to switch off the vibration.
2
Move the forward/reverse lever (2) to the neutral
position to stop the roller.
1
Always activate the parking brake (3), before leaving
the operator platform.
3 When starting and driving a machine that is cold,
remember that the hydraulic fluid is also cold and
that braking distances can be longer than normal
until the machine reaches the working temperature.
Fig. Control panel
1. Vibration On/Off switch
3. Parking brake
4812159601_E.pdf 2018-04-25
70
Operation
If the forward/reverse lever is moved quickly (forwards

or backwards) toward/past neutral, the system
switches to a rapid braking Mode and the machine
stops.
Activate normal driving Mode again by moving the
forward/reverse lever back to neutral.
Emergency braking
Braking is normally activated using the
forward/reverse lever. The hydrostatic transmission
1 retards and slows the roller when the lever is moved
towards the neutral position.
2 A disc brake in each drum motor/drum gear and the
rear axle also acts a secondary brake when in motion,
and as a parking brake when stationary. Activated with
the parking brake (2).
For emergency braking, press the emergency stop
Fig. Control panel (1), hold the steering wheel firmly and be prepared
1. Emergency stop for a sudden stop. The engine stops.
2. Parking brake
The Diesel engine will stop and must be restarted.

After emergency braking, return the forward/reverse
lever to neutral and deactivate the emergency stop.
Switching off
Set the speed control in idling position and allow the
1 engine to idle for a few minutes to cool down.
Check the display to see if any faults are indicated.
Switch off all lights and other electrical functions.
Activate the parking brake (3) and then turn the
3 ignition lock (2) to the left to the off position.
2 Fit the instrument cover on the display and top of the
control box (on rollers without cab), and lock it.
Fig. Control panel

1. Display
2. Ignition lock
3. Parking brake
2018-04-25 4812159601_E.pdf
71
Operation
Parking
Chocking the drums

Never disembark from the machine when the
diesel engine is running, unless the parking brake
is activated.
Make sure that the roller is parked in a safe place

with respect to other road users. Chock the drums
if the roller is parked on sloping ground.
1 1
Fig. Positioning
1. Chocks Keep in mind that there is a risk of freezing during
the winter. Drain the water tanks, pumps and
water lines.
Fill antifreeze in the engine cooling system and
the washer fluid reservoir in the cab. Also see
maintenance instructions.
Master switch
Before leaving the roller for the day, switch the master
switch (1) to the disconnected position and remove the
handle.
Before switching off the master switch, wait for at
1 least 30 seconds after the ignition lock has been
switched off, in order to avoid the engine's
electronic control unit (ECU) sustaining damage.
Figure. Engine door, left

1. Master switch
This will prevent battery discharging and will also

make it difficult for unauthorized persons to start and
operate the machine. Lock the service doors/covers.
4812159601_E.pdf 2018-04-25
72
Long-term parking
Long-term parking
The following instructions should be followed

when long term parking (more than one month).
These measures apply when parking for a period of up

to 6 months.
Before re-commissioning the roller, the points marked
with an asterisk * must be returned to the pre-storage
state.
Wash the machine and touch up the paint finish to

Fig. Roller weather protection avoid rusting.
Treat exposed parts with anti-rust agent, lubricate the
machine thoroughly and apply grease to unpainted
surfaces.
Engine
* Refer to the manufacturer’s instructions in the engine
manual that is supplied with the roller.
Battery
* Dismantle the battery/batteries from the machine,
clean the outside and maintenance charge.
Air cleaner, exhaust pipe

* Cover the air cleaner (see under the heading 'Every
50 hours of operation' or 'Every 1000 hours of
operation') or its opening with plastic or tape. Also
cover the exhaust pipe opening. This is to avoid
moisture entering the engine.
Watering system
* Empty the water tank and all hoses of water. Empty
the filter housing and the water pump. Undo all
sprinkler nozzles.
Fuel tank
Fill the fuel tank completely full to prevent
condensation.
Hydraulic reservoir
Fill the hydraulic reservoir to the uppermost level mark
(see under the heading ‘Every 10 hours of operation.’)
2018-04-25 4812159601_E.pdf
73
Long-term parking
Hoods, tarpaulin
* Lower the instrument cover over the instrument
panel.
* Cover the entire roller with a tarpaulin. A gap must
be left between the tarpaulin and the ground.
* If possible, store the roller indoors and ideally in a
building where the temperature is constant.
Steering cylinder, hinges, etc.

Grease the steering cylinder piston with conservation
grease.
Grease the hinges on the doors to the engine
compartment and the cab.
4812159601_E.pdf 2018-04-25
74
Miscellaneous
Miscellaneous
Lifting
Locking the articulation

Articulation must be locked to prevent inadvertent
turning before lifting the roller.
Turn the steering wheel to the straight ahead position.

Push in the emergency/parking brake knob.
Pull out the lowermost locking pin (1), which has a a

wire attached. Pull up the locking dowel (2) which also
has a wire attached.
3 2 4
1
Fig. Articulation in the locked position Fold out the locking arm (3) and secure it to the upper
1. Locking pin
2. Locking dowel locking lug (4) on the articulated link.
3. Locking arm
4. Locking lug
Fit the locking dowel into the holes through the locking
arm and locking lug. Lock the dowel in position with
the locking pin (1).
Locking the articulation
Articulation must be locked to prevent inadvertent

turning before lifting the roller.
Turn the steering wheel to the straight ahead position.

Activate the parking brake.
Front frame shall be in line with the rear frame.
2 1
Fig. Steering joint lock, locked
1. Lock handle Lift lock in the handle (1) while it is turned clockwise.
2. Locking dowel
Make sure dowel (2) gets in position as illustrated.
Arm must be in contact with the surface of the molded
holder.
If this is not done, it's likely that the machine halves
are out of line, steer then the machine so this is
happening.
2018-04-25 4812159601_E.pdf
75
Miscellaneous
Weight: refer to the hoisting plate on the

roller
Lifting the roller
The machine’s gross weight is specified on the
hoisting plate (1). Refer also to the Technical
specifications.
Lifting equipment such as chains, steel wires,

straps and lifting hooks must be dimensioned in
accordance with the relevant safety regulations
for the lifting equipment.
Stand well clear of the hoisted machine! Make sure

that the lifting hooks are properly secured.
1
Fig. Roller prepared for lifting
1. Hoisting plate
Weight: refer to the hoisting plate on the

roller
Lifting the roller with jack:
1 The machine’s gross weight is specified on the
hoisting plate (1). Refer also to the Technical
specifications.
The lifting device such as a jack (2), or

equivalent, must be dimensioned according to the
safety regulations for lifting devices.
3 3
Do not go under a lifted load! Make sure that the
lifting device is secure in its position, and on a
level and stable suface.
2
Figure. Roller lifted with jack
1. Lifting plate
2. Jack The machine must only be lifted with a jack, or the
3. Marking like, positioned as per the markings (3). The frame is
reinforced at these points to withstand the tension.
Lifting at any other place can result in damage to the
machine or personal injury.
4812159601_E.pdf 2018-04-25
76
Miscellaneous
Unlocking the articulation

Remember to unlock the articulation before
operating.
Pull out the lowermost locking pin (1), which has a a

wire attached. Pull up the locking dowel (2) which also
has a wire attached.
4 3 Fold the locking arm (3) back and secure it in the

2 locking lug (4) with the locking dowel (2).
Fig. Articulation in the unlocked The locking lug is located on the front frame of the
position
2. Locking dowel machine.
3. Locking arm
4. Locking lug
Unlocking the articulation
Remember to restore the steering joint lock on the

steering joint to open before operating.
Lift lock in the handle while turning it counterclockwise.

Make sure lock gets in position on the dowel by trying
2 1 to turn the handle clockwise or counterclockwise
Fig. Steering joint lock, open without lifting the lock.
1. Lock handle
2. Locking dowel
Towing/Recovering
The roller can be moved up to 300 meters (330 yards)

using the instructions below.
2018-04-25 4812159601_E.pdf
77
Miscellaneous
Short distance towing with the engine running

Activate the parking brake, and temporarily stop
the diesel engine. Chock the drums to prevent the
roller from moving
Open the left door to the engine compartment to

access the propulsion pump.
At the bottom on the forward drive pump are two
towing valves (1) which need to be set in bypass mode.
1
2 1 Loosen the towing valve (1) with the hexagonal nut (A)
2 by turning it a number of turns to the left, counter-hold
Fig. Propulsion pump
1. Towing valve on the overflow valve (2).
2. Bypass valve
After releasing the hexagonal nut (A), screw in the
adjusting screw (B) with a hex key until it touches the
pin (C) and then turn an additional ½ turn. The valve is
now open.
A B Start the engine and allow it to idle.

Deactivate the parking brake and place the
forward/reverse lever in the forward or reverse
position. If the lever is in neutral, the brakes in the
hydraulic motors are activated.
C
The roller can now be towed and can also be steered
if the steering system is otherwise functioning.
Do not forget to reset the towing valves after
performing towing.
Figure. Towing valve To leave the by-pass position, unscrew the adjusting
screw (B) until it stops and then lock the valve again
with the hex nut (A).
4812159601_E.pdf 2018-04-25
78
Miscellaneous
Short distance towing when the engine is

inoperative.
Chock the drums to prevent the roller from moving
when the brakes are hydraulically disengaged.
3 2
Open both towing valves as described earlier.

The brake disengagement pump is located behind the
1 left door of the engine compartment.
Make sure that the valve (1) is closed, this is done by
Fig. Brake disengagement valve tightening clockwise with the knob (3). Pump with the
1. Valve
2. Pump arm pump arm (2) until the brakes are disengaged.
3. Knob
Ensure that the valve is reset into open position after
finished towing. This is done by turning the knob
counter clockwise to full extracted position.
Towing the roller

When towing/recovering, the roller must be braked
by the towing vehicle. A towing bar must be used
as the roller has no brakes.
The roller must be towed slowly, max. 3 km/h (2

mph) and only towed short distances, max. 300 m
(330 yards).
When towing/retrieving a machine, the towing device

must be connected to both lifting holes in the diagram.
The load is uniformly divided between the two lugs.
The pulling forces should act parallel to the machine's
longitudinal axis, as shown in the figure. See table
below for maximum permitted pulling force.
Fig. Towing
Model kN lbf
CC224-384, CC2200-3800 140 31 500
CC424-624, CC4200-6200 190 42 750
Reverse the towing preparations made to the

hydraulic pump and/or the motor.
2018-04-25 4812159601_E.pdf
79
Miscellaneous
Trailer eye
The roller can be fitted with a trailer eye.
The trailer eye is not designed to be used for
towing/recovering. It is designed for trailers and other
towed objects weighing no more than 2 600 kg (5 750
lbs).
Fig. Trailer eye
Transport
Tie-down and secure the machine according to the
Cargo Securing Certificate for the specific machine if
this is avaliable and applicable.
If not, tie down and secure the machine according to
the cargo securing rules that are valid for the country
where the transport takes place.
Never lash over the machine’s articulated joint, nor
over the machine’s operator platform.
Before securing the machine ensure that :

• the parking brake is applied and in good working condition
• the articulated joint is in closed position
• the machine is centered laterally on the platform
• the lashings are in good condition and fulfills the
corresponding rules for transport securing.
4812159601_E.pdf 2018-04-25
80
Miscellaneous
Loading CC224-624, CC2200-6200

Securing vibratory roller CC224-624, CC2200-6200
from Dynapac for transport.
(The instructions also apply to Combi machines)
Roller loaded in
forward
direction
Direct of travel
*) Lashing 2 to be moved to a rear lashing point if side beam on the trailer is missing.
1 - 3 = double lashings, i.e. one lashing with two parts secured to two different lashing mounts,
symmetrically located on the right and left sides.
4 = rubber
The lashings' permitted distance interval in meters

(1 - 3: Double lashings, LC at least 1.7 tonnes (1700 daN), STF 300 kg (300daN))
Double L1 Double L2 Double L3
0,9 - 2,5 0,8 - 2,5 0,1 - 2,5
For lashing 1 is L1 the distance between the lashing point on the edge of the platform and the point directly sideways
from the lashing point on the roller perpendicular to the platform edge. The relationship for lashings L2 and L3 is the
same.
2018-04-25 4812159601_E.pdf
81
Operating instructions - Summary
Load carrier
- When loaded, the vibratory roller is centered laterally on the platform (± 5 cm).
- The parking brake is applied and in good working condition, and the articulated joint lock is
closed.
- The drums are placed on rubber liners, so that the static friction between the surfaces is at
least 0.6.
- The contact surfaces must be clean, wet or dry, and free from frost, ice and snow.
- The lashing mounts on the load carrier have LC/MSL at least 2 tonnes.
Lashings
- The lashings comprise a lashing strap or chain with a permitted load (LC/MSL) of at least 1.7
tonnes (1,700 daN) and a pre-tension STF of at least 300 kg (300 daN). The lashings are
re-tightened as required.
- Each of lashings 1-3 is either a double or two single lashings. A double lashing runs in a sling
through a lashing point or around a machine part and down into two different fasteners on the
platform. Note that lashing 2 may be moved to a rear lashing point if side beam on the trailer is
missing.
- Lashings in the same direction are placed in different lashing mounts on the trailer. Lashings
that are pulled in opposite directions may be placed in the same lashing mount, however.
- The lashings are as short as possible.
- The lashing hooks must not lose grip if the lashings become slack.
- The lashings are protected against sharp edges and corners.
- The lashings are located symmetrically in pairs on the right and left sides.
4812159601_E.pdf 2018-04-25
82
1. Follow the SAFETY INSTRUCTIONS specified in the Safety Manual.
2. Make sure that all instructions in the MAINTENANCE section are followed and the
steering hitch lock is unlocked.
3. Turn the master switch to the ON position.
4. Move the forward/reverse lever to the NEUTRAL position. Sit down in the seat.
5. Engage the parking brake.
6. Disengage the emergency stop. The roller is always starting in transportation

mode.
7. Set the rpm switch in position idle (LO).
8. Start the engine and allow it to warm up.
9. Set the rpm switch in position working speed (HI) or (ECO).
10. Disengage the parking brake.
11. Drive the roller. Operate the F/R lever with care.
12. Test the brakes. Remember that the braking distance will be longer if the
hydraulic fluid is cold.
13. Set the transportation/working mode button in position working mode.
14. Use vibration only when the roller is in motion.
15. Check that the drums are thoroughly watered when watering is required.
16. IN AN EMERGENCY:
- Press the EMERGENCY STOP.
- Hold the steering wheel firmly.
- Brace yourself for a sudden stop.
17. When parking:

- Activate the parking brake.
- Switch off the engine and block the drums if the roller is on an inclined surface.
18. When lifting: - Refer to the relevant section in the Instruction Manual.
19. When towing: - Refer to the relevant section in the Instruction Manual.
20. When transporting: - Refer to the relevant section in the Instruction Manual.
2018-04-25 4812159601_E.pdf
83
21. When recovering - Refer to the relevant section in the Instruction Manual.
4812159601_E.pdf 2018-04-25
84
Preventive maintenance
Complete maintenance is necessary for the machine
to function satisfactorily and at the lowest possible
cost.
The Maintenance section includes the periodic
maintenance that must be carried out on the machine.
The recommended maintenance intervals assume that
the machine is used in a normal environment and
working conditions.
Acceptance and delivery inspection

The machine is tested and adjusted before it leaves
the factory.
On arrival, before delivery to the customer, delivery
inspection must be conducted as per the check list in
the warranty document.
Any transport damage must be reported immediately
to the transport company, as this is not covered by the
product warranty.
Warranty
The warranty is only valid if the stiplulated delivery
inspection and the separate service inspection have
been completed as per the warranty document, and
when the machine has been registered for starting
under the warranty.
The warranty is not valid if damage has been caused
by inadequate service, incorrect use of the machine,
the use of lubricants and hydraulic fluids other than
those specified in the manual, or if any other
adjustments have been made without the requisite
authorisation.
2018-04-25 4812159601_E.pdf
85
4812159601_E.pdf 2018-04-25
86
Maintenance - Lubricants and symbols
Fluid volumes
Drum
- Drum CC224, CC2200 13 liters 13.7 qts
- Drum CC324/384, 14 liters 14.8 qts
CC3200/3800
- Drum gear 0,8 liters 0.85 qts
Hydraulic reservoir 40 liters 42 qts
Diesel engine, Cummins
- oil 7 liters 7.4 qts
- coolant, no cab 18,6 liters 19.7 qts
- coolant, with cab 19,8 liters 20.9 qts
Diesel engine, Deutz
- oil 8 liters 8.5 qts
- coolant, no cab 18,9 liters 20.0 qts
- coolant, with cab 20,1 liters 21.2 qts
Always use high-quality lubricants and the

amounts recommended. Too much grease or
oil can cause overheating, resulting in rapid
wear.
Other fuel and lubricants are required when

operating in areas with extremely high or
extremely low ambient temperatures. See the
‘Special instructions’ chapter, or consult
Dynapac.
ENGINE OIL Air temperature -15°C - +50°C Dynapac engine oil 200 P/N 4812161855 (5 liters),
(5°F-122°F) P/N 4812161856 (20 liters)
HYDRAULIC FLUID Air temperature -15°C - +50°C Dynapac hydraulic 300 P/N 4812161868 (20 liters),
(5°F-122°F) P/N 4812161869 (209
liters)
Air temperature over +40°C Shell Tellus S2 V100
(104°F)
BIOLOGICAL Air temperature -10°C - +35°C PANOLIN HLP Synth 46
HYDRAULIC FLUID, (14°F-95°F) (www.panolin.com)
PANOLIN When it leaves the factory, the
machine may be filled with
biologically degradable fluid.
The same type of fluid must be
used when changing or topping
up.
2018-04-25 4812159601_E.pdf
87
DRUM OIL Air temperature -15°C - +40°C Dynapac Drum Oil 1000 P/N 4812161887 (5 liters),
(5°F-104°F) P/N 4812161888 (20 liters)
GREASE Dynapac Roller Grease P/N 4812030096

(0.4kg)
FUEL See engine manual. - -
TRANSMISSION OIL Air temperature -15°C - +40°C Dynapac Gear oil 200 P/N 4812161879 (5 liters),
(5°F-104°F) P/N 4812161880 (20 liters)
Air temperature 0°C (32°F) - Shell Spirax S3 AX
above +40°C (104°F) 85W/140, API GL-5
COOLANT Anti-freeze protection down to Dynapac coolant 100 P/N 4812161854 (20 liters)
about -37°C (-34.6°F) (mixed 50/50 with water)
Maintenance symbols
Engine, oil level Air filter
Engine, oil filter Battery
Hydraulic reservoir, level Sprinkler
Hydraulic fluid, filter Sprinkler water
Drum, oil level Recycling
Lubricating oil Fuel filter
Coolant level Pump gear, oil level
Air pressure Sprinkler, tires
4812159601_E.pdf 2018-04-25
88
Maintenance - Maintenance schedule
Service and maintenance points
9 5 22
14
14
14
12
1 2 20 14
15 3
12 24
13
11
23
17
6, 7 8
21
18 13 3 19
16 10
4 25
Fig. Service and maintenance points
1. Engine oil 9. Coolant 17. Steering joint

2. Oil filter 10. Air cleaner 18. Seat bearing
3. Fuel filter 11. Refueling point 19. Rubber element
4. Hydraulic filter 12. Scrapers 20. Battery
5. Hydraulic fluid level 13. Water tank(s), filling 21. Pivot bearing
6. Hydraulic fluid, filling 14. Watering system 22. Cab, air filter
7. Hydraulic tank cap 15. Drum gear/Wheel gear 23. Cab, AC
8. Hydraulic fluid cooler 16. Drum oil 24. Edge cutter
25. Wheel
General
Periodic maintenance should be carried out after the
number of hours specified. Use the daily, weekly etc.
periods where number of hours cannot be used.
2018-04-25 4812159601_E.pdf
89
Remove all dirt before filling, when checking

oils and fuel and when lubricating using oil or
grease.
The manufacturer’s instructions found in the

engine manual also apply.
Specific maintenance and checks on diesel
engines must be carried out by the engine
supplier’s certified personnel.
Every 10 hours of operation (Daily)

Refer to the contents to find the page number of the
sections referred to !
Pos. Action Comment

in fig
Before starting up for the first time on that day
1 Check the engine oil level Refer to the engine manual
9 Check the engine coolant level
5 Check the hydraulic reservoir level
11 Refuel
13 Fill the water tanks
14 Check the sprinkler system
14 Check the Emergency watering (Extra pump in pump
system)
12 Check the scraper setting
After the FIRST 50 hours of operation

Pos. Action Comment

in fig
4 Change the hydraulic fluid filter Refer to 1000h.
15 Change the oil in the drum gears Refer to 1000h.
17 Steering hitch - Tightening Refer to 1000h.
4812159601_E.pdf 2018-04-25
90
Every 50 hours of operation (Weekly)

Pos. Action Comment

in fig
15 Check the oil level in the drum gears
3 Draining the fuel prefilter
Check that hoses and connections are tight
Every 250 hours of operation (Monthly)

Pos. Action Comment

in fig
1,2 Change the engine oil and oil filter * Refer to the engine manual
*) only for Cummins
8 Clean the hydraulic fluid cooler/water cooler Or when required
20 Check the batteries condition.
22,23 Check the AC Optional
24 Check/lubricate the edge cutter Optional
2018-04-25 4812159601_E.pdf
91
Every 500/1500 hours of operation

Pos. Action Comment

in fig
1,2 Change the diesel engine oil and oil filter **, *** See the engine's instruction
manual
**) only for Deutz
***) 500 h or once every 6
months
3 Replace fuel filter * Refer to the engine manual
*) only for Cummins
3 Replace fuel prefilter * *) only for Cummins
8 Clean the hydraulic fluid cooler/water cooler Or when necessary
10 Check the filter element in the air cleaner Replace when necessary
20 Check the condition of the batteries
16 Check the oil level in the drums
19 Check rubber elements and bolted joints
18 Grease the chair bearing
22,23 Check the AC Optional
21 Lubricate the pivot bearings Optional
Every 1000 hours of operation (Every six

months)
Pos. Action Comment

in fig
Check engine valve clearances Refer to the engine manual
Check the engine belt drive system Refer to the engine manual
3 Change the fuel filter ** **) only for Deutz
3 Change fuel pre-filter (insert) ** **) only for Deutz
3 Change engine v-belt ** **) only for Deutz
10 Replace the air cleaner's main filter and backup filter.
4 Change the hydraulic fluid filter
16 Change the oil in the drums
15 Change the oil in the drum gears
17 Steering hitch - Tightening
22 Replace the air cleaner filter in the cab
4812159601_E.pdf 2018-04-25
92
Every 2000 hours of operation

Pos. Action Comment

in fig
3 Change the diesel engine oil and oil filter **,*** Refer to the engine manual
**) Deutz, 500h or once every
6 months
***) Cummins, 1000h or once
a year
3 Replace fuel filter
3 Replace fuel filter (filter insert*) *) Deutz
3 Replace engine V-belt * *) only for Deutz
Check engine valve clearances Refer to the engine manual
Check the engine belt drive system Refer to the engine manual
8 Clean the hydraulic fluid cooler/water cooler Or when necessary
10 Check the filter element in the air cleaner Replace when necessary
20 Check the condition of the batteries
4 Change the hydraulic fluid filter
7 Check the hydraulic reservoir cover/breather
6 Change the hydraulic fluid
16 Change the oil in the drums
15 Change the oil in the drum gear boxes
19 Check the rubber elements and bolted joints
18 Grease the chair bearing
17 Steering hitch - Tightening
22 Replace the air cleaner filter in the cab
23 Overhaul the air conditioning
21 Lubricate the pivot bearing Offset drum
2018-04-25 4812159601_E.pdf
93
4812159601_E.pdf 2018-04-25
94
Maintenance, 10h
Maintenance, 10h
Every 10 hours of operation (Daily)
Park the roller on a level surface.
The engine must be switched off and the
parking brake activated when checking or
adjusting the roller, unless otherwise specified.
Ensure that there is good ventilation (air

extraction) if the engine is run indoors. Risk of
carbon monoxide poisoning.
Diesel engine - Check oil level
2
The dipstick is accessed through the right door of the
engine compartment.
Take care not to touch any hot parts of the engine
or the radiator when removing the dipstick. Risk of
burns.
The dipstick is located down on the front of the engine.

1
Pull out the dipstick (1) and check that the oil level is
between the upper and lower marks.
For further details, refer to the engine's instruction
Fig. Engine compartment manual.
1. Dipstick
2. Oil filler cap
2018-04-25 4812159601_E.pdf
95
Maintenance, 10h
Coolant level - Check
1
Check that the coolant level is between the max. and
min. marks (2).
Observe great caution if the cap has to be opened
while the engine is hot. Wear protective gloves and
goggles.
2 Fill with a mixture of 50% water and 50% anti freeze.

See the lubrication specification in these instructions
and the engine manual.
Fig. Expansion tank Flush the system every other year and change
1. Filler cap the coolant. Also check that the air has
2. Level marks unobstructed passage through the reservoir.
Fuel tank - Refueling
2 1 Never refuel while the engine is running. Do not

smoke and avoid spilling fuel.
The filler pipe and tank cap are on the left side of the
front frame.
Refuel the tank every day before starting work, or fill
Fig. Fuel tank the tank at end of work. Unscrew the lockable tank cap
1. Tank cap (1) and fill fuel up to the lower edge of the filler pipe.
2. Filler pipe
The tank holds 130 liters (34 gal) of fuel. Refer to the
engine manual for information on diesel grade.
4812159601_E.pdf 2018-04-25
96
Maintenance, 10h
Water tank, Std - Filling
The filler cap is on the rear left side of the front frame.
Unscrew the tank cap (1) and fill with clean
1 water. Do not remove the strainer (2).
Fill the central (standard) tank, it holds 750 liters (198

gal).
Only additive: A small amount of
environment-friendly antifreeze.
Figure. Standard water tank
1. Tank cap
Hydraulic reservoir - Check fluid level
2
Place the roller on a level surface and check that the
oil level in the sight glass (1) is between the max and
min markings. Top up with the type of hydraulic fluid
specified in the lubricant specification, if the level is too
low.
1
Figure. Hydraulic reservoir

1. Oil sight glass
2. Filler cap
2018-04-25 4812159601_E.pdf
97
Maintenance, 10h
Check
Start the sprinkler system and make sure that none of

1 the nozzles (1) are clogged. If necessary, clean
blocked nozzles and the coarse filter placed by the
water pump (2). See next section.
Figure. Front drum

1. Nozzle
Cleaning the coarse filter

To clean the coarse filter (1) open the drain cock (3)
1 on the filter and allow any dirt to run out.
If necessary close the cock (2) and clean the filter and
filter housing. Check that the rubber gasket in the filter
housing is intact.
2
After inspecting and cleaning, reset and start the
system to check that it works.
6 4 3 There is a drain cock (5) in the space for the pump
system. This can be used to drain the tank and the
pump system.
5
An extra pump (6) can be installed in case the
standard water pump stops working. See section for
Figure. Pump system, front frame emergency watering.
right side
1. Coarse filter To drain the complete sprinkler system, see section for
2. Stop cock Watering system - Draining, 2,000 h.
3. Drain cock kran, filter
4. Water pump
5. Drain cock
6. Extra pump (optional)
4812159601_E.pdf 2018-04-25
98
Maintenance, 10h
Cleaning of sprinkler nozzle
1 Dismantle the blocked nozzle by hand.
Blow the nozzle and fine filter (1) clean using
2 compressed air. Alternatively, fit replacement parts
and clean the blocked parts later on.
Nozzle Colour Ø (mm) l/min gal/min
(2.0 bar) (40 psi)
Figure. Nozzle Standard yellow 0.8 0.63 0.20
1. Sleeve, nozzle, filter
2. Packing Option blue 1.0 1.00 0.31
Option red 1.2 1.25 0.39
Option brown 1.3 1.63 0.50
After inspecting and carrying out any necessary

cleaning, start the system and check that it works.
Wear protective goggles when working with
compressed air.
Cleaning of sprinkler nozzle
Dismantle the blocked nozzle by hand.
Blow the nozzle (1) and fine filter (3) clean using
compressed air. Alternatively, fit replacement parts
and clean the blocked parts later on.
1
Nozzle Colour l/min (at 2.0 gal/min (at
2 bar) 40 psi)
Standard yellow 0.63 0.20
3
Option blue 0.98 0.30
Option red 1.31 0.40
Figure. Nozzle Option brown 1.63 0.50
1. Nozzle
2. Gasket
3. Filter After inspecting and carrying out any necessary
cleaning, start the system and check that it works.
compressed air.
2018-04-25 4812159601_E.pdf
99
Maintenance, 10h
Emergency watering (Accessory) - Extra pump

in pump system
If the water pump stops, an extra pump will keep the

sprinkler system in operation.
Connect the electric cable and water hoses to the
extra pump instead of the standard pump.
The water hoses are connected to the pump with quick
couplings to simplify draining and where appropriate
replacement to a reserve pump (option).
1
Figure. Panel on right side of front
frame
1. Extra pump
Scrapers, spring-action
Check
Make sure that the scrapers are undamaged.
Release with the arm (1).
2 Loosen the screws (3) to adjust the scraper blade up

3 or down.
1
Figure. Outer scrapers
1. Release arm
2. Scraper blade
3. Adjusting screw
Asphalt remnants can accumulate on the scraper and

affect the contact force. Clean when necessary.
The scrapers must be retracted from the drum
during transport driving.
1
2
Figure. Inner scrapers

1. Release arm
2. Lifting handle
4812159601_E.pdf 2018-04-25
100
Maintenance, 10h
Scrapers
Setting - Adjustment
2 Release the retaining unit (1) for the scraper bracket
and unscrew the adjusting screw (2) to release.
Push in the scraper bracket and tighten.
Adjust the screw (2) so that the scraper blade lies
approx. 2 mm (0.08 in) from the drum on the same
side as the screw.
1 Adjust the scraper bracket in or out on the other side
so that there is an equal gap between the scraper
blade and drum, and tighten the retaining unit (1).
1-2 mm
(0.04-0.08 in)
2 3 The adjusting screw (2) is adjusted until the scraper

blade has a gap of approx. 1 mm (0.04 in) to the roller,
or lies loosely on the roller, along its entire length.
Tighten the lock nut (3).
Figure. Scraper setting

1. Retaining unit
2. Adjusting screw
3. Lock nut
2018-04-25 4812159601_E.pdf
101
Maintenance, 10h
4812159601_E.pdf 2018-04-25
102
Maintenance - 50h
Maintenance - 50h
Every 50 hours of operation (Weekly)

Fuel filter - Draining
Unscrew the drain plug (1) at the bottom of the fuel

filter.
2
With the aid of the secondary hand-operated pump,
1 make certain that all sediment comes out. See
Cummins service manual.
Tighten the drain plug as soon as uncontaminated fuel

runs out.
Figure. Fuel filter

1. Drain plug
2. Hand pump
2018-04-25 4812159601_E.pdf
103
Maintenance - 50h
Drum gear - Checking the oil level

2 Move the machine until the inspection/filling holes are
in position for filling.
2
1 Fig. Drum gear
Refill with new oil. Use transmission oil according to

Fig. Oil level check - drum gear the lubricant specification.
1. Level plug
2. Filling plug Ensure that the oil level reaches up to the lower edge
of the plug hole.
Clean and refit the plugs.
4812159601_E.pdf 2018-04-25
104
Maintenance - 250h
Maintenance - 250h


Diesel engine
Oil change
The engine's oil drain plug is located under the rear
frame on the machine on the right side.The drain plug
is accessed by first removing the rubber plug on the
underside of the frame.
Drain the oil when the engine is warm. Place a
receptacle that holds at least 14 liters (15 qts) under
the drain plugs.
Take great care when draining engine oil. Wear
protective gloves and goggles.
1 Unscrew the drain plug (1). Allow all the oil to drain out
and refit the plug.
Figure. Underside of rear frame
Deliver the drain oil for environmentally correct
1. Oil draining of diesel engine handling.
Fill with fresh engine oil, see Lubricant specification or

the engine manual for the correct grade of oil.
Fill with the requisite volume of engine oil. See
technical specifications before starting the machine.
Allow the engine to idle for a few minutes, and then
switch off the engine.
Check the dipstick to ensure that the engine oil level is
correct. Refer to the engine manual for details. Top up
with oil if necessary to the max mark on the dipstick.
2018-04-25 4812159601_E.pdf
105
Maintenance - 250h
Engine
Replacing oil filter
Check the dipstick (2) to ensure that the engine oil

level is correct. Refer to the engine manual for details.
2 The oil filter (1) can be accessed via the right engine
compartment door.
1 See the engine manual for information about replacing

the filter.
Fig. Engine compartment, right side
1. Oil filter
2. Dipstick

Checking - Cleaning
The water and hydraulic fluid coolers are accessible

when the cooler grill (4) is removed.
Make sure that the air flow through the cooler is
unobstructed. Dirty coolers are blown clean with
compressed air or washed clean using a
high-pressure water cleaner.
Take care when using a high-pressure water jet.

Do not hold the nozzle too near the cooler.
3 1 2
4
Figure. Cooler
1. Charge air cooler
2. Water cooler
3. Hydraulic fluid cooler Wear protective goggles when working with
4. Cooler grill
compressed air or high-pressure water jets.
4812159601_E.pdf 2018-04-25
106
Maintenance - 250h
Battery
- Check condition
The batteries are sealed and maintenance-free.
Make sure there is no open flame in the vicinity

when checking the electrolyte level. Explosive gas
is formed when the alternator charges the battery.
Figure. Batteries
When disconnecting the battery, always

disconnect the negative cable first. When
connecting the battery, always connect the
The cable shoes should be clean and tightened.

Corroded cable shoes should be cleaned and greased
with acid-proof Vaseline.
Wipe the top of the battery.

- Inspection
1 2 Inspect refrigerant hoses and connections and make
sure that there are no signs of an oil film that can
indicate a refrigerant leakage.
If there is a signifcant loss of cooling capacity, clean
the condensor element (2) on the rear edge of the cab
roof.
3
Fig. Air conditioning

1. Refrigerant hoses
2. Condensor element
3. Drying filter
2018-04-25 4812159601_E.pdf
107
Maintenance - 250h

Drying filter - Inspection
With the unit in operation, check using the sight glass
(1) that bubbles are not visible on the drying filter.
Park the roller on a level surface, chock the wheels

2 1 and activate the parking brake.
Figure. Drying filter

1. Sight glass The filter is placed at the top of the rear part of the cab
2. Filter holder roof.
If bubbles are visible through the sight glass, this
indicates that the refrigerant level is too low. Stop the
unit to avoid risking damage. Fill up with refrigerant.
The refrigerant circuit is only to be worked on by
authorized companies.

- Lubrication
2 Refer to the operation section for information on

how to operate the edge cutter.
1 Grease the two points as shown in the figure.

Grease should always be used for lubrication, see the
lubricant specifications.
Grease all bearing points with five strokes of a
Figure. Two grease points for hand-operated grease gun.
lubricating the edge cutter
4812159601_E.pdf 2018-04-25
108
Maintenance - 500h
Maintenance - 500h


Diesel engine
Oil change
the drain plugs.
and refit the plug.

2018-04-25 4812159601_E.pdf
109
Maintenance - 500h
Engine

compartment door.

the filter.
1. Oil filter
2. Dipstick
The engine fuel filter - replacement/cleaning
The fuel filter is placed on the left side of the engine

compartment.
1 Unscrew the bottom and drain off any water, and then
replace the filter unit.
Figure. Engine compartment, left side

1. Prefilter
Replace the fuel filter, located on the right side of the

engine compartment.
Start the engine and check that the filter is well sealed.
Figure. Engine compartment, right

side.
1. Fuel filter
4812159601_E.pdf 2018-04-25
110
Maintenance - 500h

Checking - Cleaning


3 1 2
4
Figure. Cooler
2. Water cooler
4. Cooler grill
Battery
- Check condition

Figure. Batteries


2018-04-25 4812159601_E.pdf
111
Maintenance - 500h
Air cleaner
Checking - Change the main air filter
Change the air cleaner's main filter when the
warning lamp on the display lights when the
diesel engine is operating at full speed.
2 3
Release the clips (1), pull off the cover (2), and pull out
the main filter (3).
Do not remove the backup filter (4).
Clean the air cleaner if necessary, see section Air
cleaner - Cleaning.
1 4 5 When replacing the main filter (3), insert a new filter

6 and refit the air cleaner in the reverse order.
Fig. Air cleaner Check the condition of the dust valve (6); replace if
1. Clips
2. Cover necessary.
3. Main filter
4. Backup filter When refitting the cover, make sure that the dust valve
5. Filter housing is positioned downwards.
6. Dust valve
Backup filter - Change
1 Change the backup filter with a new filter after every

second replacement of the main filter.
To change the backup filter (1), pull the old filter out of
its holder, insert a new filter and reassemble the air
cleaner in the reverse order.
cleaner - Cleaning.
Fig. Air filter

1. Backup filter
4812159601_E.pdf 2018-04-25
112
Maintenance - 500h
Air cleaner
- Cleaning
Wipe clean on both sides of the outlet
pipe. Wipe clean the inside of the cover (2) and the filter
housing (5). See the previous illustration.
Wipe also both surfaces for the outlet pipe; see

adjacent figure.
Inner edge of Outer edge of outlet

outlet pipe. pipe.
Check that the hose clamps between the filter

housing and the suction hose are tight and that
the hoses are intact. Inspect the entire hose
system, all the way to the engine.
Drum - oil level

Inspection - filling
Position the roller with the filler plug (1), the large plug,
at the highest point in its rotation.
Wipe clean around the level plug (2), the small plug,
1 and remove the plug.
Make sure that the oil level is up to the lower edge of
the hole. Top off with fresh oil if the level is low. Use oil
as specified in the lubricants specification.
2
When removing the filler plug, wipe any metal
accumulated on the plug magnet off. Make sure that
plug seals are intact and replace with new seals if not.
Fig. Drum, vibration side
1. Filler plug Refit the plugs and check that they are tight by driving
2. Level plug the roller and then rechecking.
2018-04-25 4812159601_E.pdf
113
Maintenance - 500h

Check
Check all rubber elements (1). Replace all elements if
25% or more than 25% of the number on one side of
the drum have cracks deeper than 10-15 mm (0.4-0.6
in).
1
Check using a knife blade or pointed object.
Check also that the attachment screws (2) are
tightened.
2

1. Rubber element
2. Attachment screws
Seat bearing - Lubrication
5 Keep in mind that the chain is a vital part of the

steering mechanism.
6
Remove the cover (5) to access the lubrication nipple

(1). Lubricate the operator seat slew bearing with three
2 strokes of a hand-operated grease gun.
Clean and grease the chain (3) between the seat and
3 the steering column.
4
1 Also grease the seat slide rails (6).
7 If the chain is slack on the sprocket (2), loosen the
Figure. Seat bearing screws (4) and move the steering column forward.
1. Grease nipple Tighten the screws and check chain tension.
2. Gearwheel
3. Steering chain No not tension the chain too tightly. It should be
4. Adjusting screw possible to move the chain about 10 mm (0.4 in) to the
5. Cover
6. Slide rails side with a forefinger/thumb at the marking (7) in seat
7. Marking frame. Fit the chain lock at the bottom.
If the seat starts to be stiff when adjusting, it
should be lubricated more often than specified
here.
4812159601_E.pdf 2018-04-25
114
Maintenance - 500h
Pivot bearing (Optional) - Lubrication
Grease each nipple (1) with five strokes of a

hand-operated grease gun.
Use grease as specified in the lubricant specification.
1
Fig. Rear drum

1. Grease nipples x 4
Hydraulic reservoir cap - Check
Turn up the machine so that the tank cap is accessible

from the left side of the machine.
Unscrew and make sure that the reservoir cap is not
clogged. Air must have unobstructed passage through
the cap in both directions.
1
If passage in either direction is blocked, clean the filter

with a little diesel oil and blow through with
Figure. Rear frame front left side compressed air until the block is removed, or replace
1. Hydraulic reservoir cap the cap with a new one.
compressed air.
2018-04-25 4812159601_E.pdf
115
Maintenance - 500h

- Inspection
1 2 Inspect refrigerant hoses and connections and make
sure that there are no signs of an oil film that can
indicate a refrigerant leakage.
If there is a signifcant loss of cooling capacity, clean
the condensor element (2) on the rear edge of the cab
roof.
3
Fig. Air conditioning

1. Refrigerant hoses
2. Condensor element
3. Drying filter



4812159601_E.pdf 2018-04-25
116
Maintenance - 500h

- Lubrication


2018-04-25 4812159601_E.pdf
117
Maintenance - 500h
4812159601_E.pdf 2018-04-25
118
Maintenance - 1000h
Maintenance - 1000h
Performed after 1000 operating hours (each year)

Diesel engine
Oil change
the drain plugs.
and refit the plug.

2018-04-25 4812159601_E.pdf
119
Maintenance - 1000h
Engine

compartment door.

the filter.
1. Oil filter
2. Dipstick

compartment.

1. Prefilter

engine compartment.

side.
1. Fuel filter
4812159601_E.pdf 2018-04-25
120
Maintenance - 1000h

Checking - Cleaning


3 1 2
4
Figure. Cooler
2. Water cooler
4. Cooler grill
Battery
- Check condition

Figure. Batteries


2018-04-25 4812159601_E.pdf
121
Maintenance - 1000h
Air cleaner
2 3
cleaner - Cleaning.

1. Clips
2. Cover necessary.
3. Main filter
6. Dust valve

cleaner - Cleaning.
Fig. Air filter

1. Backup filter
4812159601_E.pdf 2018-04-25
122
Maintenance - 1000h
Air cleaner
- Cleaning

adjacent figure.

outlet pipe. pipe.

2018-04-25 4812159601_E.pdf
123
Maintenance - 1000h
Hydraulic filter
Change
Remove the filter (1) and deliver to special waste
handling. This is a single-use filter and cannot be
cleaned.
Thoroughly clean the filter holder sealing surface.

Apply a thin coat of fresh hydraulic fluid to the rubber
gasket on the new filter.
Screw the filter on by hand, firstly until the filter gasket
makes contact with the filter base. Then rotate a
further ½ turn.
Figure. Engine compartment, left

1. Hydraulic fluid filter
Check the hydraulic fluid level in the sight glass (3)

2 and top off as required. See under the heading 'Every
10 hours of operation' for more information.
Start the engine and check that the filter does not leak.
Figure. Hydraulic tank

2. Hydraulic reservoir cap
3. Sight glass
4812159601_E.pdf 2018-04-25
124
Maintenance - 1000h
Drum - Oil change
Take great care when draining the fluid. Wear

Set the roller so that the drain plug (1), the large plug,
is at the lowest position in its rotation.
Place a receptacle that holds at least 20 liters (5.3 gal)
1 under the drain plug.
Fig. Drum, vibration side Remove the drain plug (1). Allow all the oil to drain out
1. Drain plug and refit the plug.
Deliver the drain oil to environmentally correct
handling.
See under the heading 'Every 500 hours of operation'

for filling oil.
Drum gear - Oil change
Place the roller on a level surface.

Wipe clean, unscrew the plugs (1, 2) and drain the oil
into a suitable receptacle, capacity about 2 liters (0.5
gal.).
2
2
Fig. Drum gear
1
1
Fig. Drum gear
1. Drain plug
2. Ventilating plug
2018-04-25 4812159601_E.pdf
125
Maintenance - 1000h

2
1 Fig. Drum gear

1. Level plug
of the plug hole.

Check
in).
1
tightened.
2

1. Rubber element
4812159601_E.pdf 2018-04-25
126
Maintenance - 1000h

steering mechanism.
6

4
2. Gearwheel
5. Cover
here.

1
Fig. Rear drum

2018-04-25 4812159601_E.pdf
127
Maintenance - 1000h

1

compressed air.
Steering hitch - Tightening

Nobody must be allowed near the steering joint
when the engine is running. Risk of being
crushed when the steering is operated. Switch
off the engine and activate the parking brake
1 before lubricating.
The easiest way to identify if you have this type of

steering hitch is that it has a new type of nut (1) at the
top, as shown.
Fig. Steering hitch

1. Nut Actual torque (Nm) should be when the machine's
position is straight ahead.
M14 174 Nm
M16 270 Nm
4812159601_E.pdf 2018-04-25
128
Maintenance - 1000h
Cab
Fresh air filter - Replacing
There is one fresh air filter (1), placed on the front of

the cab.
Remove the protective cover.
Undo the screws (2) and remove the complete holder.
Remove the filter insert and replace with a new filter.
2 The filter may need to be changed more often if the
machine is operated in a dusty environment.
2 1
Fig. Cab, front
1. Fresh air filter (x1)
2. Screw (x2)

- Overhaul
Regular inspection and maintenance is necessary to

ensure satisfactory long-term operation.
Clean all dust from the condenser element (1) using
compressed air. Blow from above downwards.
The air jet can damage the element flanges if it is

too powerful.
2 1
Figure. Cab Wear protective goggles when working with
1. Condensor element compressed air.
2. Drying filter
Inspect the condenser element attachment.

Check the system hoses for chafing. Make sure that
drainage from the cooling unit is unobstructed so that
condensation does not accumulate inside the unit.
2018-04-25 4812159601_E.pdf
129
Maintenance - 1000h




- Lubrication


4812159601_E.pdf 2018-04-25
130
Maintenance - 2000h
Maintenance - 2000h
Performed after 2000 operating hours (every two
years)

Diesel engine
Oil change
the drain plugs.
and refit the plug.

2018-04-25 4812159601_E.pdf
131
Maintenance - 2000h
Engine

compartment door.

the filter.
1. Oil filter
2. Dipstick

compartment.

1. Prefilter

engine compartment.

side.
1. Fuel filter
4812159601_E.pdf 2018-04-25
132
Maintenance - 2000h

Checking - Cleaning


3 1 2
4
Figure. Cooler
2. Water cooler
4. Cooler grill
Battery
- Check condition

Figure. Batteries


2018-04-25 4812159601_E.pdf
133
Maintenance - 2000h
Air cleaner
2 3
cleaner - Cleaning.

1. Clips
2. Cover necessary.
3. Main filter
6. Dust valve

cleaner - Cleaning.
Fig. Air filter

1. Backup filter
4812159601_E.pdf 2018-04-25
134
Maintenance - 2000h
Air cleaner
- Cleaning

adjacent figure.

outlet pipe. pipe.

2018-04-25 4812159601_E.pdf
135
Maintenance - 2000h
Hydraulic filter
Change
Remove the filter (1) and deliver to special waste
handling. This is a single-use filter and cannot be
cleaned.
Thoroughly clean the filter holder sealing surface.

Apply a thin coat of fresh hydraulic fluid to the rubber
gasket on the new filter.
Screw the filter on by hand, firstly until the filter gasket
makes contact with the filter base. Then rotate a
further ½ turn.
Figure. Engine compartment, left

1. Hydraulic fluid filter
Check the hydraulic fluid level in the sight glass (3)

2 and top off as required. See under the heading 'Every
10 hours of operation' for more information.
Start the engine and check that the filter does not leak.
Figure. Hydraulic tank

2. Hydraulic reservoir cap
3. Sight glass
4812159601_E.pdf 2018-04-25
136
Maintenance - 2000h
Drum - Oil change
Take great care when draining the fluid. Wear

Set the roller so that the drain plug (1), the large plug,
is at the lowest position in its rotation.
Place a receptacle that holds at least 20 liters (5.3 gal)
1 under the drain plug.
Fig. Drum, vibration side Remove the drain plug (1). Allow all the oil to drain out
1. Drain plug and refit the plug.
Deliver the drain oil to environmentally correct
handling.
See under the heading 'Every 500 hours of operation'

for filling oil.
Drum gear - Oil change
Place the roller on a level surface.

Wipe clean, unscrew the plugs (1, 2) and drain the oil
into a suitable receptacle, capacity about 2 liters (0.5
gal.).
2
2
Fig. Drum gear
1
1
Fig. Drum gear
1. Drain plug
2. Ventilating plug
2018-04-25 4812159601_E.pdf
137
Maintenance - 2000h

2
1 Fig. Drum gear

1. Level plug
of the plug hole.

Check
in).
1
tightened.
2

1. Rubber element
4812159601_E.pdf 2018-04-25
138
Maintenance - 2000h

steering mechanism.
6

4
2. Gearwheel
5. Cover
here.

1
Fig. Rear drum

2018-04-25 4812159601_E.pdf
139
Maintenance - 2000h

1

compressed air.
Hydraulic reservoir
Fluid change
2 3 1 Take care when draining the hydraulic fluid. Wear

Open left engine compartment. The drain plug/valve is

in the area under the hydraulic tank.
Place a receptacle that holds at least 50 liters (13.2
gal) under the engine compartment.
Make sure that the valve (3) is closed.
Figure. Engine compartment under
hydraulic tank (via left side) Unscrew the oil drain plug (1), and connect a drain
1. Oil drain hose out from the engine compartment.
2. Hydraulic tank
3. Valve Open the valve (3) and allow all the oil to run out.
Reset by closing the valve and refitting the plug (1).
Deliver the drained fluid to environmentally
correct handling.
Fill with fresh hydraulic fluid. Refer to the lubricants

specification for grade information.
Replace the hydraulic filter. See section "Maintenance
- 1000 hours".
Start the engine and operate the hydraulic functions.
Check the level in the reservoir and top off as required.
4812159601_E.pdf 2018-04-25
140
Maintenance - 2000h
Fuel tank
- Cleaning
1 It is easiest to clean the tank when it is almost empty.

A drain plug is placed under the left side of the front
frame.
Alternatively drain the tank with a suitable pump, e.g.
an oil drain pump, to bring up any bottom sediment.
Collect the fuel and sediment in a container and
deliver to environmentally correct handling.
Fig. Fuel tank

1. Oil drain pump Keep in mind fire risk when handling fuel.
Watering system
- Draining
Remember that there is a risk of freezing during
the winter. Empty the tank, pump, filter and lines,
or mix antifreeze in the water.
3
1 There is a drain cock (2) in the space for the pump

system on the central water tank. This can be used to
4 drain both the tank and parts of the pump system.
2 The water hoses are connected to the pump with quick
couplings (4) to simplify draining and where
Figure. Pump system
appropriate replacement to a reserve pump (option).
1. Filter housing
2. Drain cock
3. Stop cock
4. Quick couplings
The outlet hose from the central tank can be

disconnected and the end placed in a container with
antifreeze to run this through the pump/filter.
2018-04-25 4812159601_E.pdf
141
Maintenance - 2000h
Water tank - Cleaning
Clean the tank/tanks with water and a suitable

detergent for plastic surfaces.
Close the drain cock (2), fill with water and check for
leaks.
The water tanks are made of plastic
2 (polyethylene) and are recyclable.
Figure. Water tank

2. Drain plug
Steering joint - Check

Inspect the steering joint to detect any damage or
cracks.
Check and tighten any loose bolts.
Check also for any stiffness or play in the steering joint.
Fig. Steering joint
4812159601_E.pdf 2018-04-25
142
Maintenance - 2000h
Steering hitch - Tightening

Nobody must be allowed near the steering joint
when the engine is running. Risk of being
crushed when the steering is operated. Switch
off the engine and activate the parking brake
1 before lubricating.
The easiest way to identify if you have this type of

steering hitch is that it has a new type of nut (1) at the
top, as shown.
Fig. Steering hitch

1. Nut Actual torque (Nm) should be when the machine's
position is straight ahead.
M14 174 Nm
M16 270 Nm
Cab
Fresh air filter - Replacing
There is one fresh air filter (1), placed on the front of

the cab.
Remove the protective cover.
Undo the screws (2) and remove the complete holder.
Remove the filter insert and replace with a new filter.
2 The filter may need to be changed more often if the
machine is operated in a dusty environment.
2 1
Fig. Cab, front
1. Fresh air filter (x1)
2. Screw (x2)
2018-04-25 4812159601_E.pdf
143
Maintenance - 2000h

- Overhaul
Regular inspection and maintenance is necessary to

ensure satisfactory long-term operation.
Clean all dust from the condenser element (1) using
compressed air. Blow from above downwards.
The air jet can damage the element flanges if it is

too powerful.
2 1
Figure. Cab Wear protective goggles when working with
1. Condensor element compressed air.
2. Drying filter
Inspect the condenser element attachment.

Check the system hoses for chafing. Make sure that
drainage from the cooling unit is unobstructed so that
condensation does not accumulate inside the unit.



4812159601_E.pdf 2018-04-25
144
Maintenance - 2000h

- Lubrication


2018-04-25 4812159601_E.pdf
145
Dynapac Compaction Equipment AB
Box 504, SE 371 23 Karlskrona, Sweden
www.dynapac.com

Dynapav 150 PDF

Uploaded by

Copyright:

Available Formats

Dynapav 150 PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Dynapav 150 PDF

Uploaded by

Copyright:

Available Formats

Instruction manual

Operating & Maintenance

Translation of original instruction

Reservation for changes

WARNING ! Marks a danger or a hazardous

CAUTION ! Marks a danger or hazardous

It is recommended to at least train operators in

The safety manual supplied with the machine

We recommend that the operator reads the

Read the entire manual before starting the

Replace immediately the instruction manuals if

Ensure good ventilation (extraction of air by fan)

THINK ENVIRONMENT ! Do not release oil,

This manual contains instructions for periodic

Additional instructions for the engine can be

CE marking and Declaration of conformity

Safety - General instructions

2. Ensure that all instructions in the MAINTENANCE section are followed.

3. Only trained and/or experienced operators are to operate the roller.

4. Never use the roller if it is in need of adjustment or repair.

7. Drive slowly in sharp bends.

11. Drive particularly carefully on uneven ground.

14. Safety measures before refueling:

15. Before repairs or service:

19. For your own protection always wear:

Safety - when operating

Prevent persons from entering or remaining in

Avoid driving across a slope. Drive straight up

Driving near edges

Keep in mind that the machine's center of gravity

To exit the cab in an emergency, release the

It is recommended that ROPS (Roll Over Protective

The system contains pressurized refrigerant. It is

Work on the refrigerant circuit is only to be carried

The cooling system is pressurized. Incorrect

Fig. Air conditioning (ACC)

The system must be re-filled with an approved

3 The edge cutter consists of rotating components

1 The tool must be returned to the transport

Working lights - Xenon

Warning, high voltage!

The working lights of the Xenon type have a

Figure. Xenon lighting on cab

Warning, environmentally hazardous waste!

Working lights of the Xenon type include a discharge

Standard lubricants and other recommended

The maximum ambient temperature for

Higher ambient temperatures, above +40°C

Lower ambient temperature - Freeze risk

High pressure cleaning

The Electrical Drive Control and the computer

Detergent that can destroy electrical parts, or

Never aim the water jet directly at the fuel tank

Roll Over Protective Structure (ROPS), ROPS

If the machine is fitted with a Roll Over

Never attempt to repair a damaged ROPS

When removing batteries, always disconnect the

When fitting batteries, always connect the

Dispose of old batteries in an environmentally