Data Sheet DS/266GST/AST-EN Rev.

Model 266GST Gauge

Model 266AST Absolute

2600T series pressure transmitters

Engineered solutions for all

applications

Base accuracy Flexible configuration options

— 0.04 % of calibrated span (optional 0.025 %) — Local configuration via keys on LCD indicator

Proven sensor technology together with state-of-the-art New TTG (through-the-glass) key technology
digital technology — Enables quick and easy local configuration without the
— Large turn down ratio of up to 100:1 need to open the cover - even in environments with
explosion protection
Comprehensive selection of sensors
— Optimized performance and stability IEC 61508 certification
— For SIL2 (1oo1) and SIL3 (1oo2) applications
10-year stability
— 0.15 % of URL Full compliance with Pressure Equipment Directive (PED)
category III
Change from one to two columns
Model 266GST Gauge
Model 266AST Absolute

Functional specification Span limits

Maximum span = URL
Measuring range limits and span limits Foir optimum measuring accuracy, it is recommended that you
select the sensor code which will provide the lowest TD value.
Sensor code Upper range Lower range Minimum measuring span
limit (URL) limit (LRL) 266GST 266AST Zero position suppression and elevation
266GST (Δ) The zero position and span can be set to any value within the
6 kPa -6 kPa 0.2 kPa 0.3 kPa measuring range limits listed in the table if:
C 60 mbar -60 mbar 2 mbar 3 mbar — Set span ≥ minimum span
24 inH2O -24 inH2O 0.8 inH2O 2.25 mmHg
40 kPa -40 kPa 0.4 kPa 2 kPa Damping
F 400 mbar -400 mbar 4 mbar 20 mbar Configurable time constant between 0 and 60 s.
160 inH2O -160 inH2O 1.6 inH2O 15 mmHg This is in addition to the sensor response time.
250 kPa 2.5 kPa 12.5 kPa
L 2,500 mbar 0 abs 25 mbar 125 mbar Warm-up time
1,000 inH2O 10 inH2O 93.8 mmHg Ready for operation as per specifications in less than 10 s with
1,000 kPa 10 kPa 50 kPa minimum damping.
D 10 bar 0 abs 100 mbar 500 mbar
145 psi 1.45 psi 7.25 psi Insulation resistance
3,000 kPa 30 kPa 150 kPa >100 MΩ at 500 V DC (between terminals and ground).
U 30 bar 0 abs 0.3 bar 1.5 bar
435 psi 4.35 psi 21.7 psi
10,000 kPa 100 kPa 500 kPa
R 100 bar 0 abs 1 bar 5 bar
1,450 psi 14.5 psi 72.6 psi
60,000 kPa 600 kPa
V 600 bar 0 abs 6 bar -
8,700 psi 87 psi

(Δ) Measuring range lower limit (LRL) for 266AST is 0 abs for all measuring ranges

Change from two to one column

2 DS/266GST/AST-EN Rev. B | 2600T Series Pressure Transmitters 266GST, 266AST

Operating limits Test pressure
The transmitter can be be subjected to a line pressure up to
Pressure limits the following values without leakage:
Gauge pressure limits
Without damage to the transmitter Sensors Gauge pressure limits
Sensor C, F 0 absolute and
Sensors Gauge pressure limits 1 MPa, 10 bar, 145 psi
Sensor C, F 0 absolute and Sensor L 0 absolute and
1 MPa, 10 bar, 145 psi 0.5 MPa, 5 bar, 72.5 psi
Sensor L 0 absolute and Sensor D 0 absolute and
0.5 MPa, 5 bar, 72.5 psi 2 MPa, 20 bar, 290 psi
Sensor D 0 absolute and Sensor U 0 absolute and
2 MPa, 20 bar, 290 psi 6 MPa, 60 bar, 870 psi
Sensor U 0 absolute and Sensor R 0 absolute and
6 MPa, 60 bar, 870 psi 20 MPa, 200 bar, 2,900 psi
Sensor R 0 absolute and Sensor V 0 absolute and
20 MPa, 200 bar, 2,900 psi 90 MPa, 900 bar, 13,050 psi
Sensor V 0 absolute and Perfluoroelastomer gasket 0 absolute and
90 MPa, 900 bar, 13,050 psi 0.6 MPa abs, 6 bar abs, 87 psia
Perfluoroelastomer gasket 0 absolute and T ≥ -15 °C (5 °F)
0.6 MPa abs, 6 bar abs, 87 psia 0.18 MPa abs, 1.8 bar abs, 26 psia
T ≥ -15 °C (5 °F) T ≥ -25 °C (-13 °F)

0.18 MPa abs, 1.8 bar abs, 26 psia

T ≥ -25 °C (-13 °F) Meets hydrostatic test requirements of
ANSI/ISA–S 82.03.

2600T Series Pressure Transmitters 266GST, 266AST | DS/266GST/AST-EN Rev. B 3

Model 266GST Gauge
Model 266AST Absolute

Temperature limits °C (°F) Process

Environment
This is the operating temperature Models 266GST, 266AST Process temperature limits
Silicone oil -50 ... 121 °C (-58 ... 250 °F)
Models 266GST, 266AST Ambient temperature limits Fluorocarbon (Galden) -40 ... 121 °C 1 (-40 ... 250 °F)
Silicone oil -40 ... 85 °C (-40 ... 185 °F) White oil -6 ... 121 °C (21 ... 250 °F)
Fluorocarbon (Galden) -40 ... 85 °C (-40 ... 185 °F) Viton gasket -20 ... 121 °C (-4 ... 250 °F)
White oil -6 ... 85 °C (21 ... 185°F) Perfluoroelastomer gasket -25 or -15 ... 80 °C
(-13 or 5 ... 176°F)
Important See the section titled "Pressure
For applications in explosive environments, the temperature limits".
range specified on the certificate / approval applies dependent
upon the degree of protection sought. 1 ≤ 85 °C (185 °F) for operating pressures below the atmospheric pressure

Models 266GST, 266AST Ambient temperature limits Storage

Integrated LCD display -40 ... 85 °C (-40 ... 185 °F)
Viton gasket -20 ... 85 °C (-4 ... 185 °F) Models 266GST, 266AST Storage temperature range
Perfluoroelastomer gasket -25 or -15 ... 80 °C Storage temperature -50 ... 85 °C (-58 ... 185 °F)
(-13 or 5 ... 176 °F) Integrated LCD display -40 ... 85 °C (-40 ... 185 °F)
See the section titled "Pressure White oil -6 ... 85 °C (21 ... 185 °F)
limits".

Below –20 °C (-4 °F) and above 70 °C (158 °F), it may no

longer be possible to read the LCD display clearly.
Change from two to one column

4 DS/266GST/AST-EN Rev. B | 2600T Series Pressure Transmitters 266GST, 266AST

Change from one to two columns

Limits for environmental effects Hazardous atmospheres

Electromagnetic compatibility (EMC) With or without integral LCD display
Meets requirements of EN 61326 and Namur NE-21
Overvoltage strength (with surge protection): 4 kV (in acc. with "Intrinsic Safety" type of protection:
IEC 1000-4-5 EN 61000-4-5) Approval acc. to ATEX Europa (code E1) and IEC Ex (code E8)
II 1 G Ex ia IIC T6/T5/T4 and
Pressure Equipment Directive (PED) II 1/2 G Ex ia IIC T6/T5/T4; IP67.
Meets requirements of Directive 97/23/EC Category III, II 1 D Ex iaD 20 T85 °C and
module H. II 1/2 D Ex iaD 21 T85 °C; IP67.
NEPSI China (Code EY)
Humidity Ex ia IIC T4T6, DIP A20TA, T4~T6.
Relative humidity: Up to 100 %. "Flameproof Enclosure" type of protection:
Condensation, icing: Permissible. Approval acc. to ATEX Europa (code E2) and IEC Ex (code E9)
II 1/2 G Ex d IIC T6 and
Vibration resistance II 1/2 D Ex tD A21 T85 °C (–50 °C ≤ Ta ≤+75 °C); IP67.
Acceleration up to 2 g at frequencies of up to 1,000 Hz NEPSI China (Code EZ)
(according to IEC 60068-2-6). Ex d IIC T6, DIP A21T A, T6.
"nL" type of protection:
Shock resistance ATEX Europa (code E3) and IEC Ex (code ER)
Acceleration: 50 g Declaration of conformity
Duration: 11 ms II 3 G Ex nL IIC T6/T5/T4 and
(according to IEC 60068-2-27). II 3 D Ex tD A22 T85 °C; IP67.
NEPSI China (code EY) declaration of conformity
Humid and dusty atmospheres (degree of protection) Ex nL IIC T4T6, DIP A22TA, T6.
The transmitter is dust and sand-proof and protected against FM approvals for USA (code E6) and
immersion effects as defined by EN 60529 (1989) to IP 67 FM approvals for Canada (code E4):
(IP 68 on request), by NEMA to 4X, or by JIS C0920. — Explosionproof (US): Class I, Div. 1, Groups A, B, C, D
IP 65 with Harting Han plug connector. — Explosionproof (Canada): Class I, Div. 1, Groups B, C, D
— Dust ignitionproof : Class II, Div. 1, Groups E, F, G
— Suitable for: Class II, Div. 2, Groups F, G; Class III, Div.1, 2
— Nonincendive: Class I, Div. 2, Groups A, B, C, D
— Intrinsically safe: Class I, II, III, Div. 1, Groups A, B, C, D, E, F, G
Class I, Zone 0 AEx ia IIC T6/T4, Zone 0 (FM US)
Class I, Zone 0 Ex ia IIC T6/T4, Zone 0 (FM Canada)
ATEX combined (code EW = E1 + E2 + E3), (code E7 = E1 + E2)
ATEX combined and FM approvals (code EN = EW + E4 + E6)
Combined FM approvals for USA and Canada
— Intrinsic safety (code EA)
— Flameproof enclosure (code EB)
— Non-incendive (code EC)
IEC combined (code EH = E8 + E9), (code EI = E8 + E9 + ER)
NEPSI combined (code EP = EY + EZ), (code EQ = EY + EZ + ES)
— GOST (Russia), GOST (Kazakhstan), Inmetro (Brazil) based on ATEX

The permissible ambient temperature ranges (within the limits

of -50 and 85 °C) are specified in the type examination
Change from two to one column
certificates dependent upon the temperature class.

2600T Series Pressure Transmitters 266GST, 266AST | DS/266GST/AST-EN Rev. B 5

Model 266GST Gauge
Model 266AST Absolute

Electrical data and options Integrated LCD display with TTG operation (code L5)
As with the integrated LCD display above, but featuring an
HART digital communication and 4 ... 20 mA output innovative TTG (through-the-glass) keypad which can be used
Power supply to activate the device's configuration and management menus
The transmitter operates from 10.5 ... 42 V DC with no load without having to remove the transmitter housing cover.
and is protected against reversed polarity (additional loads The TTG keys are protected against accidental activation.
enable operation above 42 V DC).
During use in Ex ia zones and in other intrinsically safe Surge protection (optional)
applications, the power supply must not exceed 30 V DC. Up to 4 kV
Minimum operating voltage with "surge protection" option: — Voltage: 1.2 μs rise time / 50 μs delay time at half value
12.3 V DC — Current: 8 μs rise time / 20 μs delay time at half value

Ripple Output signal

Max. 20 mV over a 250 Ω load as per HART specifications. Two-wire output 4 ... 20 mA, can be selected by user: linear
or linearization table with 22 points (e.g., for level
Load limitations measurements in horizontal, cylindrical containers or spherical
Total loop resistance at 4 ... 20 mA and HART: vessels).
HART communication provides digital process variables
Voltage supply –Minimum operating voltage (V DC) superimposed on the 4 ... 20 mA signal (protocol according to
R (kΩ)= Bell 202 FSK standard).
22 mA
Output current limits (according to NAMUR standard)
A minimum resistance of 250 Ω is required for HART Overload condition
communication. — Lower limit: 3.8 mA (configurable from 3.8 ... 4 mA)
— Upper limit: 20.5 mA (configurable from 20 ... 21 mA)
Displays (optional)
Integrated LCD display (code L1) Alarm current
Widescreen LCD display, 128 x 64 pixels, — Minimum alarm current: 3.6 mA (configurable from
52.5 x 27.2 mm (2.06 x 1.07 in.) dot matrix. Multilanguage. 3.6 ... 4 mA)
Four keys for device configuration and management. — Maximum alarm current: 21 mA (configurable from
Easy setup for quick commissioning. 20 ... 22 mA)
Customized visualizations which the user can select. Default setting: High Alarm Current
Totalized and actual value flow indication.
The display can also be used to show static pressure, sensor
temperature, and diagnostics messages, as well as make
configuration settings.

6 DS/266GST/AST-EN Rev. B | 2600T Series Pressure Transmitters 266GST, 266AST

FOUNDATION fieldbus output Output interface
Model FOUNDATION fieldbus digital communication protocol in
LINK MASTER accordance with standard H1; complies with specification
Link Active Scheduler (LAS) capability implemented. V. 1.7.
Manufacturer code: 000320 (hex) FF registration in progress.
Device type code: 0007 (hex)
Integrated LCD display
Power supply Widescreen LCD display, 128 x 64 pixels,
The transmitter operates from 9 … 32 V DC, regardless of 52.5 x 27.2 mm (2.06 x 1.07 in.) dot matrix. Multilanguage.
polarity, with or without surge protection. Four keys for device configuration and management.
During use in EEx ia zones, the power supply must not exceed Easy setup for quick commissioning.
24 V DC (entity certification) or 17.5 V DC (FISCO certification) Customized visualizations which the user can select.
according to FF-816. The display can also be used to show sensor temperature and
diagnostics messages, as well as make configuration settings.
Current consumption
Operating (quiescent): 15 mA Transmitter interference mode
Fault current limit value: 20 mA max. The output signal is "frozen" at the last valid value in the event
of significant transmitter interference, once this interference is
Output signal detected by the self-diagnostics function (which also displays
Physical layer in accordance with IEC 11582 / EN 611582; error states).
transmission using Manchester II modulation at 31.25 kbit/s. In the event of electronics failures or short circuits, the
transmitter consumption is electronically limited to a defined
Function blocks / cycle time value (approx. 20 mA) in order to ensure network safety.
3 enhanced analog input blocks / 25 ms max. (each)
1 extended PID block / 40 ms max.
1 standard arithmetic block / 25 ms
1 standard input selector block / 25 ms
1 standard control selector block / 25 ms
1 standard signal characterization block / 25 ms
1 standard integrator / totalizer block / 25 ms

Additional blocks
1 enhanced resource block
1 manufacturer-specific pressure with calibration
transducer block
1 manufacturer-specific advanced diagnostics transducer
block
1 manufacturer-specific local display transducer block

Number of link objects

35

Number of VCRs
35

2600T Series Pressure Transmitters 266GST, 266AST | DS/266GST/AST-EN Rev. B 7

Model 266GST Gauge
Model 266AST Absolute

PROFIBUS PA output Integrated LCD display

Model Widescreen LCD display, 128 x 64 pixels,
Pressure transmitter, compliant with Profile 3.0.1 52.5 x 27.2 mm (2.06 x 1.07 in.) dot matrix. Multilanguage.
ID number: 3450 (hex) Four keys for device configuration and management.
Easy setup for quick commissioning.
Power supply Customized visualizations which the user can select.
The transmitter operates from 9 … 32 V DC, regardless of The display can also be used to show sensor temperature and
polarity, with or without surge protection. diagnostics messages, as well as make configuration settings.
The power supply must not exceed 17.5 V DC when used in
EEx ia zones. Transmitter interference mode
Intrinsically safe installation in accordance with FISCO model. In the event of significant transmitter interference that is
detected by the self-diagnostics function, the output signal
Current consumption can be put into defined states that the user is able to select:
Operating (quiescent): 15 mA safe value, last valid value, or calculated value.
Fault current limit value: 20 mA max. In the event of electronics failures or short circuits, the
transmitter consumption is electronically limited to a defined
Output signal value (approx. 20 mA) in order to ensure network safety.
Physical layer in accordance with IEC 1158 2 / EN 61158-2;
transmission using Manchester II modulation at 31.25 kbit/s.

Output interface
PROFIBUS PA communication according to
PROFIBUS DP 50170 Part 2 / DIN 19245 Part 1-3.

Output cycle time

25 ms

Data blocks
1 "physical block"
3 "analog input" blocks
1 "pressure transducer block" with calibration
1 "transducer block" for local display

8 DS/266GST/AST-EN Rev. B | 2600T Series Pressure Transmitters 266GST, 266AST

Change from one to two columns

Measuring accuracy Ambient temperature

Per 20 K change within the limits of -40 to 85 °C
Reference conditions according to IEC 60770. (per 36 °F change within the limits of
Ambient temperature 20 °C (68 °F), rel. humidity 65 %, -40 to 185 °F):
atmospheric pressure 1,013 hPa (1,013 mbar), measuring
span based on zero position, separation diaphragms made Model Sensor For TD range
from ceramic, stainless steel AISI 316 L, or Hastelloy, silicone 266GST C and F 10:1 ±(0.06 % URL + 0.09 % span)
oil filling fluid, HART digital trim values equal to 4 and 20 mA 266GST L to V 10:1 ±(0.03 % URL + 0.045 % span)
span end points, linear characteristic. 266AST C and F 10:1 ±(0.06 % URL + 0.09 % span)
Unless otherwise stated, errors are specified as a % of the 266AST L to R 10:1 ±(0.03 % URL + 0.045 % span)
span value.
Some measuring accuracy levels relating to the upper In the case of an ambient temperature change between -
measuring range limit (URL) are affected by the current turn 10 and 60 °C (14 and 140 °F):
down (TD); i.e., the ratio of the upper measuring range limit to
the set span. Model Sensor For TD range
FOR OPTIMUM MEASURING ACCURACY, IT IS 266GST C and F 10:1 ±(0.08 % URL + 0.08 % span)
RECOMMENDED THAT YOU SELECT THE SENSOR CODE 266GST L to V 10:1 ±(0.06 % URL + 0.06 % span)
WHICH WILL PROVIDE THE LOWEST TD VALUE. 266AST C and F 10:1 ±(0.2 % URL + 0.1 % span)
266AST L to R 10:1 ±(0.06 % URL + 0.06 % span)
Dynamic response (according to IEC 61298-1)
Per 10 K change within the limits of -40 to -10 °C
Sensors Time constant (63.2 % of total or 60 to 85 °C
step response) (per 18 °F change within the limits of
Sensor C to V (all) 150 ms -40 to 14 °F or 140 to 185 °F):
Reaction time for all sensors 40 ms
Model Sensor For TD range
Response time (total) = reaction time + time constant 266GST C and F 10:1 ±(0.04 % URL + 0.05 % span)
266GST L to V 10:1 ±(0.03 % URL + 0.045 % span)
Measuring error 266AST C and F 10:1 ±(0.1 % URL + 0.05 % span)
% of calibrated span, consisting of terminal-based non- 266AST L to R 10:1 ±(0.03 % URL + 0.045 % span)
linearity, hysteresis, and non-repeatability.
In the case of fieldbus devices, SPAN refers to the analog
input function block output scale range.

Model Sensor For TD range

266GST C to V From 1:1 to 10:1 ±0.04 %
C From 10:1 to 30:1 ±(0.04 + 0.005 x TD – 0.05) %
F to V From 10:1 to 100:1 ±(0.04 + 0.005 x TD – 0.05) %
L to R From 1:1 to 10:1 ±0.025 % (optional)
266AST C to R From 1:1 to 10:1 ±0.04 %
C to R From 10:1 to 20:1 ±(0.04 + 0.005 x TD – 0.05) %

2600T Series Pressure Transmitters 266GST, 266AST | DS/266GST/AST-EN Rev. B 9

Model 266GST Gauge
Model 266AST Absolute

Power supply Total performance

Within the specified limits for the voltage / load, the total Similar to DIN 16086
influence is less than 0.005 % of the upper measuring range Temperature change in the range -10 to 60 °C (14 to 140 °F)
limit per volt.
Model Sensor For TD Total performance
Load (with 0.04 % measuring error)
Within the specified load / voltage limits, the total influence is 266GST L to V 1:1 ± 0.126 % of calibrated span
negligible. 266AST L to R 1:1 ± 0.126 % of calibrated span

Electromagnetic field The total performance accuracy includes the measuring error
Meets all requirements of EN 61326 and NAMUR NE-21. (non-linearity including hysteresis and non-reproducibility), as
well as the thermal change in the ambient temperature as
Common-mode interference regards the zero signal and span.
No influence from 100 V rms @ 50 Hz, or 50 V DC
2
E perf = (E ΔTZ + E ΔTS ) 2 + E lin
Mounting position
The recommended mounting position is vertical, with the Eperf = Total performance
process connection pointing downward. EΔTZ = Effect of the ambient temperature on the
Any deviations from this position will lead to a zero error, zero signal
which can be corrected by adjusting the zero position. With EΔTS = Effect of the ambient temperature on the
measuring range codes C and F, a deviation of 90° has an measuring span
additional effect on the ambient temperature of up to 0.02 Elin = Measuring error
mbar/10K.

Long-term stability
± 0.15 % of URL over a period of 10 years
(± 0.05 % URL/year)

10 DS/266GST/AST-EN Rev. B | 2600T Series Pressure Transmitters 266GST, 266AST

Technical specification Plates
Stainless steel (AISI 316) for transmitter name plate,
(Please refer to the order information to check the availability certification plate, optional measuring point tag plate / settings
of different versions of the relevant model) plate attached to electronics housing, and optional tag plate
with customer data. All plates laser-labeled.
Materials
Process separation diaphragms1 Calibrate
Ceramic (Al203), gold-plated; Hastelloy C276; Standard:
Hastelloy C276, gold-plated; stainless steel AISI 316L (1.4435) — 0 to measuring range upper limit, for ambient temperature
and atmospheric pressure
Process connection1 Optional:
Stainless steel AISI 316L (1.4404), Hastelloy C276 — To specified measuring span

1 Transmitter parts that come into contact with fluid

Gasket (only for sensor codes C, F)1
2 U-bolt material: stainless steel AISI 400;
Viton, perfluoroelastomer, Buna (NBR) screw material: high-strength alloy steel or stainless steel AISI 316

Sensor filling fluid Optional extras

Silicone oil; fluorocarbon (Galden); white oil (FDA) Mounting bracket
For 60 mm (2 in.) pipes or wall mounting
Mounting bracket2
Barrel version: LCD display
Galvanized C steel with chromium passivation; Can be rotated in 90° increments into 4 positions
Stainless steel AISI 316L (1.4404)
DIN version: Additional tag plates
AISI 304 (1.4301) Code I2: For measuring point tag (up to 30 characters) and
calibration specifications (up to 30 characters: lower and
Sensor housing upper value plus unit), attached to transmitter housing.
Stainless steel AISI 316L (1.4404) Code I1: For customer data (4 lines with 30 characters each),
wired to transmitter housing
Electronics housing and cover
Aluminum alloy (copper content ≤ 0.3 %) with baked epoxy Surge protector
finish (color: RAL 9002); stainless steel AISI 316L.
Cleaning stage for oxygen applications (O2)
O-ring cover
Buna N Test certificates (test, design, characteristics, material
traceability)
Local zero position, measuring span, and write protection
settings Name plate and operating instruction language
Fiber glass-reinforced polyphenylene oxide (removable)
Communication plug connectors

2600T Series Pressure Transmitters 266GST, 266AST | DS/266GST/AST-EN Rev. B 11

Model 266GST Gauge
Model 266AST Absolute

Process connections Mounting position

1/2 – 14 NPT internal or external thread; The transmitters can be installed in any position.
DIN EN 837-1 G 1/2 B or G 1/2 B (HP) for convex seals; flush The electronic housing can be rotated into any position. A
diaphragm; for ball valve stop is provided to prevent overturning.

Electrical connections Weight

Two 1/2-14 NPT or M20 x 1.5 threaded bores for cable Approx. 2 kg (4.4 lb); additional 1.5 kg (3.3 lb) for stainless
glands, directly on housing. steel housing.
Special communication connector (on request) Add 650 g (1.5 lb) for packaging.
— HART: Straight or angled Harting Han 8D connector and
one mating plug. Packaging
— FOUNDATION fieldbus, PROFIBUS PA: M12 x 1 or 7/8 in. Carton with dimensions of 25 x 20 x 14 cm,
plug approx. (10 x 8 x 6 in.)

Terminals
HART version: Three connections for signal / external display,
for wire cross sections of up to 2.5 mm2 (14 AWG), and
connection points for testing and communication purposes
Fieldbus versions: Two signal connections (bus connection) for
wire cross sections of up to 2.5 mm2 (14 AWG)

Grounding
Internal and external ground terminals are provided for
6 mm2 (10 AWG) wire cross sections.
Change from two to one column

12 DS/266GST/AST-EN Rev. B | 2600T Series Pressure Transmitters 266GST, 266AST

Configuration Transmitter with PROFIBUS PA communication
Standard configuration
Transmitter with HART communication and 4 … 20 mA Transmitters are calibrated at the factory to the customer's
Standard configuration specified measuring range. The calibrated range and
Transmitters are calibrated at the factory to the customer's measuring point number are provided on the name plate. If
specified measuring range. The calibrated range and this data has not been specified, the transmitter will be
measuring point number are provided on the name plate. If delivered with the plate left blank and the following
this data has not been specified, the transmitter will be configuration:
delivered with the plate left blank and the following Measuring profile Pressure
configuration: Physical unit kPa
Physical unit kPa Output scale 0 % Measuring range lower limit (LRL)
4 mA Zero Output scale 100 % Measuring range upper limit (URL)
20 mA Measuring range upper limit Output Linear
(URL) Upper alarm limit Measuring range upper limit (URL)
Output Linear Upper warning limit Measuring range upper limit (URL)
Damping 1s Lower warning limit Measuring range lower limit (LRL)
Transmitter interference mode High alarm Lower alarm limit Measuring range lower limit (LRL)
Software tag Hysteresis limit value 0.5 % of output scaling
(max. 8 characters) Blank PV filter time 0s
Optional LCD display PV in kPa; output in mA and Address (set using local
in percent as bargraph control buttons) 126
Any or all of the configurable parameters listed above - Measuring point tag 30 alphanumeric characters
including the lower and upper range values (with the same unit Optional LCD display PV in kPa; output in percent as
of measurement) - can easily be changed using a portable bargraph display
HART handheld communicator or a PC running the
configuration software with the DTM for 266 models. Any or all of the configurable parameters listed above -
Specifications concerning the flange type and materials, O- including the measuring range values (with the same unit of
ring and vent / drain valve materials, and additional device measurement) - can easily be changed using a PC running the
options are stored in the transmitter database. configuration software with the DTM for 266 models.
Specifications concerning the flange type and materials, O-
Customer-specific configuration (option N6) ring and vent / drain valve materials, and additional device
The following information can be specified in addition to the options are stored in the transmitter database.
standard configuration parameters:
Description 16 alphanumeric characters Customer-specific configuration (option N6)
Supplementary information 32 alphanumeric characters The following information can be specified in addition to the
Date Day, month, year standard configuration parameters:
Description 32 alphanumeric characters
For the HART protocol, the following physical units are Supplementary information 32 alphanumeric characters
available for pressure measurements: Date Day, month, year
Pa, kPa, MPa
inH2O @ 4 °C, mmH 2O @ 4 °C, psi
inH2O @ 20 °C, ftH2O @ 20 °C, mmH2O @ 20 °C
inHg, mmHg, Torr
g/cm2, kg/cm2 , atm
mbar, bar
These and others are available for PROFIBUS and
FOUNDATION fieldbus.

2600T Series Pressure Transmitters 266GST, 266AST | DS/266GST/AST-EN Rev. B 13

Model 266GST Gauge
Model 266AST Absolute

Transmitter with FOUNDATION fieldbus communication

Standard configuration
Transmitters are calibrated at the factory to the customer's
specified measuring range. The calibrated range and
measuring point number are provided on the name plate. If
this data has not been specified, the transmitter will be
delivered with the plate left blank and the analog input
function block FB1 will be configured as follows:
Measuring profile Pressure
Physical unit kPa
Output scale 0 % Measuring range lower limit (LRL)
Output scale 100 % Measuring range upper limit (URL)
Output Linear
Upper alarm limit Measuring range upper limit (URL)
Upper warning limit Measuring range upper limit (URL)
Lower warning limit Measuring range lower limit (LRL)
Lower alarm limit Measuring range lower limit (LRL)
Hysteresis limit value 0.5 % of output scaling
PV filter time 0s
Measuring point tag 30 alphanumeric characters
Optional LCD display PV in kPa; output in percent as
bargraph display
The analog input function blocks FB2 and FB3 are each
configured for the sensor temperature measured in °C and the
static pressure measured in MPa. Any or all of the
configurable parameters listed above - including the
measuring range values - can easily be changed using a
FOUNDATION fieldbus-compatible configuration tool.
Specifications concerning the flange type and materials, O-
ring and vent / drain valve materials, and additional device
options are stored in the transmitter database.

Customer-specific configuration (option N6)

The following information can be specified in addition to the
standard configuration parameters:
Description 32 alphanumeric characters
Supplementary information 32 alphanumeric characters
Date Day, month, year
Change from two to one column

14 DS/266GST/AST-EN Rev. B | 2600T Series Pressure Transmitters 266GST, 266AST

Mounting dimensions
(not design data) - dimensions in mm (inch)
Transmitter with barrel housing – 1/2 NPT female thread

Fig. 1: Dimensions - Barrel housing – 1/2 NPT female thread

1 Settings | 2 Name plate | 3 Certification plate | 4 Process connection | 5 Terminal side | 6 LCD display housing cover |
7 Electronics side | 8 Space for removing the cover

2600T Series Pressure Transmitters 266GST, 266AST | DS/266GST/AST-EN Rev. B 15

Model 266GST Gauge
Model 266AST Absolute

Transmitter with DIN aluminum housing – 1/2 NPT external thread

Fig. 2: Dimensions - DIN aluminum housing – 1/2 NPT external thread

Transmitter with barrel housing – DIN-EN837-1 G 1/2 B connection

Fig. 3: Dimensions - Barrel housing – DIN-EN837-1 G 1/2 B connection

16 DS/266GST/AST-EN Rev. B | 2600T Series Pressure Transmitters 266GST, 266AST

Electrical connections
HART version
-
6 7 8
5 9

2 M+
4
3 60 10
2 40 80
0
20 10
% 0
0
Kent-Taylo r

+
+
+

4
- 691HT

-
F1 F2 F3 F4

PV

REVIE W CONF SERIAL

LINK

TRI M

A B C D E F G H I
1 2 3

J K L M N O P Q R
4 5 6

S T U

@ %
7
V W X
8

& /
Y Z #
9

+
3
0 -

M10023

Fig. 4: Electrical connections - HART version

1 Power supply | 2 Remote display | 3 Handheld terminal | 4 External ground connection

The HART handheld terminal can be connected to any wiring termination point in the loop, provided there is a minimum
resistance of 250 Ω between the handheld terminal and transmitter power supply. If this is less than 250 Ω, additional resistance
needs to be incorporated in order to enable communication.

2600T Series Pressure Transmitters 266GST, 266AST | DS/266GST/AST-EN Rev. B 17

Model 266GST Gauge
Model 266AST Absolute

Change from one to two columns

Fieldbus versions

Fig. 5: Plug connector - fieldbus versions 2

Pin assignment (plug)

Pin number FOUNDATION fieldbus PROFIBUS PA 3
1 DATA - DATA +
2 DATA + GROUND
3 SHIELD DATA -
4 GROUND SHIELD

Delivery scope: Plug connectors supplied loose without

mating plug (female connector) M10024
Fig. 6: Standard terminal strip
1 Internal ground terminal | 2 Fieldbus line
(regardless of polarity) | 3 External ground terminal

Change from two to one column

HART version

1 2
97 (3.82)
53 (2.09)

3
22 (0.87)

1 2
42 (1.65)

- +

79 (3.11) 52 (2.05)
69 (2.72)
M10028

Fig. 7: Harting Han connection – HART version

1 Barrel housing | 2 DIN housing | 3 Harting Han 8D (8U) socket insert for mating plug supplied (view of sockets)

18 DS/266GST/AST-EN Rev. B | 2600T Series Pressure Transmitters 266GST, 266AST

Ordering information
Basic ordering information model 266GST Gauge Pressure Transmitter
Select one character or set of characters from each category and specify complete catalog number.
Refer to additional ordering information and specify one or more codes for each transmitter if additional options are required.

Base model – 1st to 6th characters 266GST X X X X X X

Gauge pressure transmitter – base accuracy 0.04 %
Sensor Span Limits / Overpressure – 7th character continued
0.2 and 6 kPa (2 and 60 mbar, 0.8 and 24 inH2O) 1 MPa (10 bar, 145 psi) C see next page
0.4 and 40 kPa (4 and 400 mbar, 1.6 and 160 in. H2O) 1 MPa (10 bar, 145 psi) F
2.5 and 250 kPa (25 and 2500 mbar, 10 and 1000 in. H2O) 0.5 MPa (5 bar, 72.5 psi) L
10 and 1000 kPa (0.1 and 10 bar, 1.45 and 145 psi) 2 MPa (20 bar, 290 psi) D
30 and 3000 kPa (0.3 and 30 bar, 4.35 and 435 psi) 6 MPa (60 bar, 870 psi) U
100 and 10000 kPa (1 and 100 bar, 14.5 and 1450 psi) 20 MPa (200 bar, 2900 psi) R
600 and 60000 kPa (6 and 600 bar, 87 and 8700 psi) 90 MPa (900 bar, 13050 psi) V
Diaphragm Material / Fill Fluid – 8th character
AISI 316L SST (1.4435) Silicone oil (Only available with front bonded diaphragm) NACE S
Hastelloy C-276 Silicone oil (NACE) K
AISI 316L SST Inert fluid - Galden
(Only available with front bonded diaphragm / suitable for oxygen applications) NACE A
Hastelloy C-276 Inert fluid - Galden (Suitable for oxygen applications) NACE F
Hastelloy C-276 gold-plated Silicone oil NACE (Note: 1) G
Hastelloy C-276 gold-plated Inert fluid - Galden (Suitable for oxygen applications) NACE (Note: 1) E
AISI 316L SST White oil (FDA) (Only available with front bonded diaphragm) NACE 6
Hastelloy C-276 White oil (FDA) NACE Z
Process Connection Material / Type – 9th character
AISI 316L SST (1.4404) 1/2-14 NPT female NACE B
AISI 316L SST (1.4404) DIN EN 837-1 G 1/2 B NACE P
AISI 316L SST (1.4404) G 1/2 in. front bonded diaphragm NACE (Note: 1) S
AISI 316L SST (1.4404) 1/2-14 NPT male NACE T
AISI 316L SST (1.4404) DIN EN 837-1 G 1/2 B (HP) NACE (Note: 1) U
AISI 316L SST (1.4404) For ball valve connection NACE (Note: 1) V
Hastelloy C-276 1/2-14 NPT female NACE E
Hastelloy C-276 DIN EN 837-1 G 1/2 B NACE D
Hastelloy C-276 1/2-14 NPT male NACE K

2600T Series Pressure Transmitters 266GST, 266AST | DS/266GST/AST-EN Rev. B 19

Model 266GST Gauge
Model 266AST Absolute

Basic ordering information model 266GST Gauge Pressure Transmitter X X X

Gasket Material – 10th character
None N
Housing material / Electrical connection– 11th character
Aluminium alloy (Barrel type) 1/2-14 NPT A
Aluminium alloy (Barrel type) M20 x 1.5 B
Aluminium alloy (Barrel type) Harting Han connector (General purpose only) (Note: 3) E
Aluminium alloy (Barrel type) Fieldbus connector (General purpose only) (Note: 3) G
AISI 316L SST (Barrel type) 1/2-14 NPT S
AISI 316L SST (Barrel type) M20 x 1.5 T
Aluminium alloy (DIN type) M20 x 1.5 J
Aluminium alloy (DIN type) Harting Han connector (General purpose only) (Note: 3) K
Aluminium alloy (DIN type) Fieldbus connector (General purpose only) (Note: 3) W
AISI 316L SST (Barrel type) Fieldbus connector (General purpose only) (Note: 3) Z
Output – 12th character
HART digital communication and 4 ... 20 mA (No additional options) H
HART digital communication and 4 ... 20 mA (Options requested by "Additional ordering code") 1
PROFIBUS PA (No additional options) P
PROFIBUS PA (Options requested by "Additional ordering code") 2
FOUNDATION Fieldbus (No additional options) F
FOUNDATION Fieldbus (Options requested by "Additional ordering code") 3
HART digital communication and 4 ... 20 mA, SIL2 and SIL3 certified to IEC 61508 (No additional options) T
HART digital communication and 4 ... 20 mA, SIL2 and SIL3 certified to IEC 61508 (Options requested by "Additional ordering code") 8

20 DS/266GST/AST-EN Rev. B | 2600T Series Pressure Transmitters 266GST, 266AST

Additional ordering information for model 266GST
Add one or more 2-digit code(s) after the basic ordering information to select all required options.

XX XX XX XX
Accuracy
Base accuracy 0.025 % (Note: 4) D1
Explosion Protection Certification
ATEX Group II Category 1 GD - Intrinsic Safety Ex ia E1
ATEX Group II Category 1/2 GD - Flameproof Ex d (Note: 1) E2
ATEX Group II Category 3 GD - Type of protection "N" Ex nL design compliance E3
FM approval (Canada, CSA) Class I, II, Div. 1, 2, Group A to F (XP, IS, NI)
(Only available with 1/2-14 NPT or M20 electrical connections) (Note: 1) E4
FM approval (USA) Class I, II, Div. 1, 2, Group A to F (XP, IS, Nl)
(Only available with 1/2-14 NPT or M20 electrical connections) (Note: 1) E6
FM approvals (USA and Canada) Intrinsic Safety EA
FM approvals (USA and Canada) Explosion-proof (Note: 1) EB
FM approvals (USA and Canada) Non-incendive EC
Combined ATEX, FM and CSA (Only available with 1/2-14 NPT or M20 electrical connections) (Note: 1) EN
Combined ATEX - Intrinsic Safety, Flameproof and Type „N“ (Note: 1) EW
IEC Approval Group II Category 1 GD - Intrinsic Safety Ex ia E8
IEC Approval Group II Category 1/2 GD - Flameproof Ex d (Note: 1) E9
IEC Approval Group II Category 3 GD - Type of protection "N" Ex nL design compliance ER
NEPSI IIC Ex ia EY
NEPSI IIC Ex d (Note: 1) EZ
NEPSI IIC Ex nL ES
Combined NEPSI Ex ia and Ex d (Note: 1) EP
Combined NEPSI Ex ia, Ex d and Ex nL (Note: 1) EQ
Other Explosion Protection Certifications
GOST Russia - Ex ia W1
GOST Russia - Ex d (Note: 1) W2
GOST Kazakhstan - Ex ia W3
GOST Kazakhstan - Ex d (Note: 1) W4
Inmetro Brazil - Ex ia W5
Inmetro Brazil - Ex d (Note: 1) W6
Inmetro Brazil - Ex nL W7
Integral LCD
With integral LCD display L1
TTG (Through The Glass) integral digital LCD display L5

2600T Series Pressure Transmitters 266GST, 266AST | DS/266GST/AST-EN Rev. B 21

Model 266GST Gauge
Model 266AST Absolute

Additional ordering information for model 266GST XX XX XX XX XX XX XX XX

Mounting Bracket Shape / Material
For horizontal or vertical mounting on pipe and wall / Carbon steel B6
For horizontal or vertical mounting on pipe and wall / AISI 316L SST B7
Surge / Transient Protector
With integral surge / transient protector S2
Operating Instruction Language
German M1
Italian M2
Spanish M3
French M4
English M5
Swedish M7
Polish M9
Portuguese Ma
Turkish MT
Label and Tag Language
German T1
Italian T2
Spanish T3
French T4
Additional Tag Plate
Supplemental wired-on stainless steel plate (4 lines, 32 characters each) I1
Laser printing of tag on stainless steel plate I2
Configuration
Standard pressure = in. H2O / psi at 68 °F N2
Standard pressure = in. H2O / psi at 39.2 °F N3
Standard pressure = in. H2O / psi at 20 °C N4
Standard pressure = in. H2O / psi at 4 °C N5
Custom N6
Preparation Procedure
Oxygen service cleaning, Pmax = 21 MPa (210 bar, 3045 psi) or sensor overpressure (lower value),
Tmax = 60 °C / 140 °F (Only available with inert fill / viton gasket) P1
Hydrogen service preparation (Fluid Film) P2
Certificates
Inspection certificate 3.1 acc. EN 10204 of calibration C1
Inspection certificate 3.1 acc. EN 10204 of cleanliness stage C3
Inspection certificate 3.1 acc. EN 10204 of helium leakage test of the sensor module C4
Inspection certificate 3.1 acc. EN 10204 of pressure test C5
Declaration of compliance with the order 2.1 acc. EN 10204 for instrument design C6
Separate calibration record CC
Printed record of configured data of transmitter CG
PMI test on wetted parts CT

22 DS/266GST/AST-EN Rev. B | 2600T Series Pressure Transmitters 266GST, 266AST

Additional ordering information for model 266GST XX XX XX XX
Approvals
GOST Russia - Without Explosion Protection Y1
GOST Kazakhstan - Without Explosion Protection Y2
GOST Ukraine - Without Explosion Protection Y3
GOST Belarus - Without Explosion Protection Y4
Material Traceability
Certificate of compliance with the order 2.1 acc. EN 10204 for process wetted parts H1
Inspection certificate 3.1 acc. EN 10204 of pressure-bearing and process wetted parts with analysis
certificates as material verification (Note: 5) H3
Material certificate 2.2 acc. EN 10204 for the pressure bearing and process wetted parts H4
Connector
Fieldbus 7/8 in. (Recommended for FOUNDATION Fieldbus, supplied loose without female plug) U1
Fieldbus M12 x 1 (Recommended for PROFIBUS PA, supplied loose without female plug) U2
Harting Han 8D (8U), straight entry U3
Harting Han 8D (8U), angle entry U4
Harting Han 7D U5
Harting HAN 8D (8U) - For Four-Wire add-on Unit U6
Harting HAN 7D - For Four-Wire add-on Unit U7
With cable gland M20 x 1.5 U8
Housing Accessories
Integral mount manifold (price adder just for assembling, not for manifold) A1
Four-wire add-on unit: Power supply 24 V UC / Output signal 0 ... 20 mA (Note: 6) A4
Four-wire add-on unit: Power supply 24 V UC / Output signal 4 ... 20 mA (Note: 6) A6
Four-wire add-on unit: Power supply 230 V AC / Output signal 0 ... 20 mA (Note: 6) A5
Four-wire add-on unit: Power supply 230 V AC / Output signal 4 ... 20 mA (Note: 6) A7
Note 1: Not available with Sensor Span Limits code C, F
Note 2: Not available with Sensor Span Limits code C, F, V
Note 3: Select connector with additional ordering code
Note 4: Only available with Sensor Span Limits code L, D, U, R
Note 5: Minor parts with factory certificate acc. EN 10204
Note 6: Only available with Housing Material / Electrical Connection code B (Barrel housing)

Standard delivery scope (changes possible with additional ordering code)

— For standard applications (without explosion protection)
— No display, no mounting bracket, no surge protection
— Multilanguage short-form operating instruction and English labeling
— Configuration with kPa and °C units
— No test, inspection, or material certificates
Unless otherwise specified prior to manufacture, the customer shall be responsible for selecting suitable parts that make
contact with the medium and appropriate filling liquids in order to ensure compatibility with the relevant measuring medium.
Compliance with the NACE regulation is based on recommendations MR0175 / ISO 15156. Additionally, stainless steel
AISI 316, AISI 316L and Hastelloy C-276 automatically meet the criteria of MR0103, provided that they also meet the criteria of
MR0175.

2600T Series Pressure Transmitters 266GST, 266AST | DS/266GST/AST-EN Rev. B 23

Model 266GST Gauge
Model 266AST Absolute

Basic ordering information model 266AST Absolute Pressure Transmitter

Select one character or set of characters from each category and specify complete catalog number.
Refer to additional ordering information and specify one or more codes for each transmitter if additional options are required.

Base model – Characters 1 through 6 266AST X X X X X X

Absolute pressure transmitter – base accuracy 0.04 %
Sensor Span Limits / Overpressure – 7th character continued
0.3 and 6 kPa (3 and 60 mbar, 1.2 and 24 in. H2O, 2.25 and 45 mm Hg) 1 MPa (10 bar, 145 psi) C see next page
2 and 40 kPa (20 and 400 mbar, 15 and 300 mm Hg) 1 MPa (10 bar, 145 psi) F
12.5 and 250 kPa (125 and 2500 mbar, 98.3 and 1875 mm Hg) 0.5 MPa (5 bar, 72.5 psi) L
50 and 1000 kPa (0.5 and 10 bar, 7.25 and 145 psi) 2 MPa (20 bar, 290 psi) D
150 and 3000 kPa (1.5 and 30 bar, 21.7 and 435 psi) 6 MPa (60 bar, 870 psi) U
500 and 10000 kPa (5 and 100 bar, 72.5 and 1450 psi) 20 MPa (200 bar, 2900 psi) R
Diaphragm Material / Fill Fluid – 8th character
AISI 316L SST (1.4435) Silicone oil (Only available with front bonded diaphragm) NACE S
Hastelloy C-276 Silicone oil NACE K
AISI 316L SST Inert fluid - Galden
(Only available with front bonded diaphragm / suitable for oxygen applications) NACE A
Hastelloy C-276 Inert fluid - Galden (Suitable for oxygen applications) NACE F
Hastelloy C-276 gold-plated Silicone oil NACE (Note: 1) G
Hastelloy C-276 gold-plated Inert fluid - Galden (Suitable for oxygen applications) NACE (Note: 1) E
AISI 316L SST White oil (FDA) (Only available with front bonded diaphragm) NACE 6
Hastelloy C-276 White oil (FDA) NACE Z
Process Connection Material / Type – 9th character
AISI 316L SST (1.4404) 1/2-14 NPT female NACE B
AISI 316L SST (1.4404) DIN EN 837-1 G 1/2 B NACE P
AISI 316L SST (1.4404) G 1/2 in. front bonded diaphragm NACE (Note: 1) S
AISI 316L SST (1.4404) 1/2-14 NPT male NACE T
Hastelloy C-276 1/2-14 NPT female NACE E
Hastelloy C-276 DIN EN 837-1 G 1/2 B NACE D
Hastelloy C-276 1/2-14 NPT male NACE K

24 DS/266GST/AST-EN Rev. B | 2600T Series Pressure Transmitters 266GST, 266AST

Basic ordering information model 266AST Absolute Pressure Transmitter X X X
Gasket Material – 10th character
None N
Housing Material / Electrical Connection – 11th character
Aluminium alloy (Barrel type) 1/2-14 NPT A
Aluminium alloy (Barrel type) M20 x 1.5 B
Aluminium alloy (Barrel type) Harting Han connector (General purpose only) (Note: 2) E
Aluminium alloy (Barrel type) Fieldbus connector (General purpose only) (Note: 2) G
AISI 316L SST (Barrel type) 1/2-14 NPT S
AISI 316L SST (Barrel type) M20 x 1.5 T
Aluminium alloy (DIN type) M20 x 1.5 J
Aluminium alloy (DIN type) Harting Han connector (General purpose only) (Note: 2) K
Aluminium alloy (DIN type) Fieldbus connector (General purpose only) (Note: 2) W
AISI 316L SST (Barrel type) Fieldbus connector (General purpose only) (Note: 2) Z
Output – 12th character
HART digital communication and 4 ... 20 mA (No additional options) H
HART digital communication and 4 ... 20 mA (Options requested by "Additional ordering code") 1
PROFIBUS PA (No additional options) P
PROFIBUS PA (Options requested by "Additional ordering code") 2
FOUNDATION Fieldbus (No additional options) F
FOUNDATION Fieldbus (Options requested by "Additional ordering code") 3
HART digital communication and 4 ... 20 mA, SIL2 and SIL3 certified to IEC 61508 (No additional options) T
HART digital communication and 4 ... 20 mA, SIL2 and SIL3 certified to IEC 61508 (Options requested by "Additional ordering code") 8

2600T Series Pressure Transmitters 266GST, 266AST | DS/266GST/AST-EN Rev. B 25

Model 266GST Gauge
Model 266AST Absolute

Additional ordering information for model 266AST

Add one or more 2-digit code(s) after the basic ordering information to select all required options.

XX XX XX
Explosion Protection Certification
ATEX Group II Category 1 GD - Intrinsic Safety Ex ia E1
ATEX Group II Category 1/2 GD - Flameproof Ex d (Note: 1) E2
ATEX Group II Category 3 GD - Type of protection "N" Ex nL design compliance E3
FM approval (Canada, CSA) Class I, II, Div. 1, 2, Group A to F (XP, IS, NI)
(Only available with 1/2-14 NPT or M20 electrical connections) (Note: 1) E4
FM approval (USA) Class I, II, Div. 1, 2, Group A to F (XP, IS, Nl)
(Only available with 1/2-14 NPT or M20 electrical connections) (Note: 1) E6
FM approvals (USA and Canada) Intrinsic Safety
(Only available with 1/2-14 NPT or M20 electrical connections) EA
FM approvals (USA and Canada) Explosion-proof
(Only available with 1/2-14 NPT or M20 electrical connections) (Note: 1) EB
FM approvals (USA and Canada) Non-incendive
(Only available with 1/2-14 NPT or M20 electrical connections) EC
Combined ATEX, FM and CSA (Only available with 1/2-14 NPT or M20 electrical connections) (Note: 1) EN
Combined ATEX - Intrinsic Safety, Flameproof and Type „N“ (Note: 1) EW
IEC Approval Group II Category 1 GD - Intrinsic Safety Ex ia E8
IEC Approval Group II Category 1/2 GD - Flameproof Ex d (Note: 1) E9
IEC Approval Group II Category 3 GD - Type of protection "N" Ex nL design compliance ER
NEPSI IIC Ex ia EY
NEPSI IIC Ex d (Note: 1) EZ
NEPSI IIC Ex nL ES
Combined NEPSI Ex ia and Ex d (Note: 1) EP
Combined NEPSI Ex ia, Ex d and Ex nL (Note: 1) EQ
Other Explosion Protection Certifications
GOST Russia - Ex ia W1
GOST Russia - Ex d (Note: 1) W2
GOST Kazakhstan - Ex ia W3
GOST Kazakhstan - Ex d (Note: 1) W4
Inmetro Brazil - Ex ia W5
Inmetro Brazil - Ex d (Note: 1) W6
Inmetro Brazil - Ex nL W7
Integral LCD
With integral LCD display L1
TTG (Through The Glass) integral digital LCD display L5

26 DS/266GST/AST-EN Rev. B | 2600T Series Pressure Transmitters 266GST, 266AST

Additional ordering information for model 266AST XX XX XX XX XX XX XX XX
Mounting Bracket Shape / Material
For horizontal or vertical mounting on pipe and wall / Carbon steel B6
For horizontal or vertical mounting on pipe and wall / AISI 316L SST B7
Surge / Transient Protector
With integral surge / transient protector S2
Operating Instruction Language
German M1
Italian M2
Spanish M3
French M4
English M5
Swedish M7
Polish M9
Portuguese MA
Turkish MT
Label and Tag Language
German T1
Italian T2
Spanish T3
French T4
Additional Tag Plate
Supplemental wired-on stainless steel plate (4 lines, 32 characters each) I1
Laser printing of tag on stainless steel plate I2
Configuration
Standard pressure = in. H2O / psi at 68 °F N2
Standard pressure = in. H2O / psi at 39.2 °F N3
Standard pressure = in. H2O / psi at 20 °C N4
Standard pressure = in. H2O / psi at 4 °C N5
Custom N6
Preparation Procedure
Oxygen service cleaning, Pmax = 21 MPa (210 bar, 3045 psi) or sensor overpressure (lower value),
Tmax = 60 °C / 140 °F (Only available with inert fill / viton gasket) P1
Hydrogen service preparation P2
Certificates
Inspection certificate 3.1 acc. EN 10204 of calibration C1
Inspection certificate 3.1 acc. EN 10204 of cleanliness stage C3
Inspection certificate 3.1 acc. EN 10204 of helium leakage test of the sensor module C4
Inspection certificate 3.1 acc. EN 10204 of pressure test C5
Declaration of compliance with the order 2.1 acc. EN 10204 for instrument design C6
Separate calibration record CC
Printed record of configured data of transmitter CG
PMI test on wetted parts CT

2600T Series Pressure Transmitters 266GST, 266AST | DS/266GST/AST-EN Rev. B 27

Model 266GST Gauge
Model 266AST Absolute

Additional ordering information for model 266AST XX XX XX XX

Approvals
GOST Russia - Without Explosion Protection Y1
GOST Kazakhstan - Without Explosion Protection Y2
GOST Ukraine - Without Explosion Protection Y3
GOST Belarus - Without Explosion Protection Y4
Material Traceability
Certificate of compliance with the order 2.1 acc. EN 10204 for process wetted parts H1
Inspection certificate 3.1 acc. EN 10204 of pressure-bearing and process wetted parts
with analysis certificates as material verification (Note: 3) H3
Material certificate 2.2 acc. EN 10204 for the pressure bearing and process wetted parts H4
Connector
Fieldbus 7/8 in. (Recommended for FOUNDATION Fieldbus, supplied loose without female plug) U1
Fieldbus M12 x 1 (Recommended for PROFIBUS PA, supplied loose without female plug) U2
Harting Han 8D (8U), straight entry U3
Harting Han 8D (8U), angle entry U4
Harting Han 7D U5
Harting HAN 8D (8U) - For Four-Wire add-on Unit U6
Harting HAN 7D - For Four-Wire add-on Unit U7
With cable gland M20 x 1.5 U8
Housing Accessories
Integral mount manifold (price adder just for assembling, not for manifold) A1
Four-wire add-on unit: Power supply 24 V UC / Output signal 0 ... 20 mA (Note: 4) A4
Four-wire add-on unit: Power supply 24 V UC / Output signal 4 ... 20 mA (Note: 4) A6
Four-wire add-on unit: Power supply 230 V AC / Output signal 0 ... 20 mA (Note: 4) A5
Four-wire add-on unit: Power supply 230 V AC / Output signal 4 ... 20 mA (Note: 4) A7
Note 1: Not available with Sensor Span Limits code C, F
Note 2: Select connector with additional ordering code
Note 3: Minor parts with factory certificate acc. EN 10204
Note 4: Only available with Housing Material / Electrical Connection code B (Barrel housing)

Standard delivery scope (changes possible with additional ordering code)

— For standard applications (without explosion protection)
— No display, no mounting bracket, no surge protection
— Multilanguage short-form operating instruction and English labeling
— Configuration with kPa and °C units
— No test, inspection, or material certificates
Unless otherwise specified prior to manufacture, the customer shall be responsible for selecting suitable parts that make
contact with the medium and appropriate filling liquids in order to ensure compatibility with the relevant measuring medium.
Compliance with the NACE regulation is based on recommendations MR0175 / ISO 15156. Additionally, stainless steel
AISI 316, AISI 316L and Hastelloy C-276 automatically meet the criteria of MR0103, provided that they also meet the criteria of
MR0175.

28 DS/266GST/AST-EN Rev. B | 2600T Series Pressure Transmitters 266GST, 266AST

Notice

2600T Series Pressure Transmitters 266GST, 266AST | DS/266GST/AST-EN Rev. B 29

Notice

30 DS/266GST/AST-EN Rev. B | 2600T Series Pressure Transmitters 266GST, 266AST

Notice

2600T Series Pressure Transmitters 266GST, 266AST | DS/266GST/AST-EN Rev. B 31

Contact us

DS/266GST/AST-EN Rev. C 06.2012

ABB Limited Note
We reserve the right to make technical changes or
Process Automation
modify the contents of this document without prior
Howard Road, St. Neots notice. With regard to purchase orders, the agreed
Cambridgeshire, PE19 8EU particulars shall prevail. ABB does not accept any
UK responsibility whatsoever for potential errors or
possible lack of information in this document.
Tel: +44 (0)1480 475321
Fax: +44 (0)1480 217948 We reserve all rights in this document and in the
subject matter and illustrations contained therein.
ABB Inc. Any reproduction, disclosure to third parties or
utilization of its contents - in whole or in parts – is
Process Automation
forbidden without prior written consent of ABB.
125 E. County Line Road
Warminster PA 18974 Copyright© 2012 ABB
USA All rights reserved
Tel: +1 215 674 6000
Fax: +1 215 674 7183
measurement@us.abb.com 3KXP200011R1001

ABB Automation Products GmbH

Process Automation ™ Hastelloy C276 is a Cabot Corporation
Schillerstr. 72 trademark
™ Viton is a Dupont de Nemour trademark
32425 Minden
™ Galden is a Montefluos trademark
Germany
Tel: +49 551 905-534
Fax: +49 551 905-555

www.abb.com