Asme B16.10 - 2009 PDF

Face-to-Face
and End-to-End
Dimensions
ofValves
AN AMERICAN NATIONAL STANDARD
Copyright© 2009 by the American Society ofMechanical Enginecrs. ~

No reproductionmay be made of this materia! without written consent of ASME. ~
Date of lssuance: October 28, 2009
The next edition of this Standard is scheduled for publication in 2014. There will be no addenda
issued to this edition.
ASME issues written replies to lnquiries concerning interpretations of technical aspects of this
Standard.lnterpretations an d errata are published on the ASME Web site underthe Committee Pages
at http://cstools.asme.org as they are issued.
ASME is the reglstered trademark of The American Society Of Mechanical Englneers.
This code or standard was deiteloped under procedures accredlted as meeting the criteria far Amerlcan National
Standards. The Standards Commlttee that approved the code or standard was balanced to assure that indivlduals from
competent and concerned interests have had an opportunlty to partlcipate. The proposed code or standard was ma de
available for public review and commentthat provldes an opportunity far additional public lnput from lndustry, academia,
regulatory agencies, and the publlc-at-large.
ASME does not "approve," "rate," or "endorse" any Jtem, construction, proprletary device, or activity.
ASME does not take any position with respect to the validlty of any patent rights asserted in connection with any
Jtems mentloned In thls document, and does not undertake to insure anyone utllizing a standard against liability far
lnfringement of any applicable letters patent, nor assume any such liabillty. Users of a code or standard are expressly
advised that determinatlon of the valldity of any such patent rights, and the risk of infrlngement of such rights, is
entirely their own responsibillty.
Participation by federai agency representative(s) or person(s) affiliated with industry is not to be interpreted as
government or industry endorsement of this code or standard.
ASME accepts responslbi\ity far only those interpretatlons ofthis document issued in accordante wlth the established
ASME procedures and poli cles, whlch precludes the issuance of lnterpretat!ons by indivlduals.
No part of this document may be reproduced in any form,

in an electronlc retrieval system or otherwise,
without the prior written permisslon of the publlsher.
The Amerlcan Society of Mechanical Englneers

Three Park Avenue, New York; NY 10016·5990
Copyright © 2009 by
THE AMERICAN SOCIETY OF MECHANICAL ENGINEERS
Ali Rights Reserved
Prlnted in U.S.A.
Copyright © 2009 by the American Socicty ofMechanical Engineers. ~

No reproduction may be made ofthis materia! withoutwritten consent of ASME. ~
CONTENTS
Foreword . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv
Committee Roster . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v
Correspondence With the B16 Committee . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . .. . . . . . . . . . vi
1 Scope............................................................................ 1
2 Definltlons .............................................................. · · · · · · · · · 2
3 Faclngs of Flanged Valves ........................................................ . 3
4 Varlatlons ofLength Wlthln a Class of Valves .. .................................... . 3
5 Tolerances .............................................................. · · · · · · · · · 4
Flgures
1 Flange Facings and Their Relationships .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. . .. .. .. .. . 5
2 Welding Ends .. .. . .. .. .. .. . .. .. .. .. .. .. . .. .. .. .. .. .. .. .. . .. .. .. .. .. .. .. .. . .. .. .. 6
Tables
f Class 125 Cast Iron Flanged and Class 150 Steel Flanged and Buttwelding End
Valves, Face-to-Pace and End-to-End Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2 Class 250 Cast Iron Flanged and Class 300 Steel Flanged and Buttwelding End
Valves, Face-to-Pace and End-to-End Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . lO
3 Class 600 Steel Flanged and Buttweiding End Valves, Face-to-Face and End-to-End
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
4 Class 900 Steel Flanged and Buttwelding End Valves, Face-to-Face and End-to-End
Dimensions .............. , ............. , ... , . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
5 Class 1500 Steei Flanged and Buttwelding End Valves, Face-to-Face and End-lo-
End Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
6 Class 2500 Steei Flanged and Buttwelding End Valves, Face-to-Face and End-to-
End Dimensions .. .. .. .. .. .. .. .. . .. .. .. .. .. .. .. .. .. . .. .. .. . .. .. .. .. .. .. . .. . . .. 18
7 Classes 125 and 250 Cast Iron and Classes 150 to 2500 Steei Wafer Type Valves,
Face-to-Face Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
8 Classes 25 and 125 Cast lron and Classes 150 to 600 Steel Butterfly Valves,
Face-to-Face Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
9 Determination of Face-to-Face and End-to-End Dimensions of Flanged Valves
Having Various Flange Facings .. . . .. . . . .. . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . .. 21
10 Classes 150 to 2500 Steel Valves Having End Flanges With Ring Joint Facings,
End-to-End Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Mandatory Appendlx
I Face-to-Face and End-to-End Dimensions: U.S. Customary Units . . . . . . . . . . . . . . . . . . 25
Nonmandatory Appendlx
A References .. .. . .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. . .. .. . .. .. .. .. .. .. . .. .. .. 42
iii
Copyright © 2009 by the American Society of Mechanical Engineers. ~
No reproduction may be made ofthis material without written consent of ASME. ~
FOREWORD
In 1921, the American Engineering Standards Committee, later the American Standards
Association (ASA), organized Sectional Committee 616 to unify and further develop national
standards for pipe flanges and fittings (and, later, for valves, gaskets, artd valve actuators).
Cosponsors of the 616 Committee were The American Society of Mechanical Engineers (ASME),
the Heating and Piping Contractors National Association [now the Mechanical Contractors
Association of America (MCAA)], and the Manufacturers Standardization Society of the Valve
and Fittings Industry (MSS). Cosponsors were later designated as cosecretariat organizations.
Pioneer work on standardization of end-to-end dimensions of valves began in 1917 under the
direction of ). A. Stevens. It was put aside at the end of World War I and interest did not revive
unti! 1926. ASA and ASME agreed to include the topic in the scope of the 616 Committee, and
Subcommittee 5 (now Subcommittee E) was established for the purpose. Work began in 1928
and covered ferrous flanged-end gate, globe, angle, and check valves.
Development of a national standard was hindered by the diversity of existing practices and
by adverse economie conditions in the eàrly 1930s. A proposed 1933 American Standard far face-
to-face dimensions of ferrous flanged valves did not gain acceptance, even though it was largely
based an a 1931 Standard Practice of MSS. Further work and industry developments led lo a
meeting in May 1937, which undertook to reconcile differences among the draft ASA standard,
two American Petroleum lnstitute (API) standards (5-G-1 on pipeline valves and 600A on flanged
OS&Y steel wedge gate valves), and a newly updated MSS SP-32.
A revised 616 proposal was voted favorably in )une 1938, was approved by ASA, and was
published in 1939. The standard was reaffirmed in 1947. Work began on a revision in 1953 to
include buttwelding end valves, plug valves, and contro! valves in both cast iran and steel.
That edition was published as ASA 616.10-1957. Further revision was begun in 1964. Alter
reorganization of ASA, first as the United States of America Standards Institute (USASI), then
as American National Standards Institute (ANSI), with the Sectional Committee being redesig-
nated as an American National Standards Committee, a new edition adding hall valves was
approved and published as ANSI 816.10-1973.
In 1982, American National Standards Committee B16 was reorganized as an ASME Committee
operating under procedures accredited by ANSI. In the 1986 Edition, ductile iron and the alloys
covered by ANSI 616.34 were added to the materials covered. Wafer type gate and check valves,
Class 150 Y-pattern globe and check valves, and severa! patterns of butterfly valves were added to
the types covered. Inch dimensions were converted from common to two-place decimai fraçtions:
In 1991, Subcommittee E- Face-to-Face an d End-to-End Dimensions of Val ves, was combined
with Subcommittee N - Steel Valves. In the 1992 Edition, steel offset seat and grooved end
butterfly valves were added. Globe and flangeless style contro! valves, which previously had
been included, were rernoved from the Standard. Information regarding contro! valve dimensions
may be obtained from Instrument Society of America, 67 Alexandria Drive, Research Triangle
Park, NC 27709.
In the 2000 Edition, metric dimension tables were added. Ali tables and references to Class
400 steel and Class 800 cast iron were removed. Ali tables were renumbered. Following the
approvals of the Standards Committee and ASME, approvai for the new edition was granted by
the American National Standards Institute on )une 7, 2000.
In this 2009 Edition, Nonmandatory Appendix A was revised and updated. Also, ali affected
regions of this Standard were updated to reflect the changes in Nonmandatory Appendix A. PN
values and references to API 605 have been removed from the Standard.
Following approvai by the 616 Standards Committee and the ASME Supervisory 6oard, this
Standard was approved as an American National Standard by ANSI an )une 15, 2009.
iv
Copyright © 2009 by the American Society ofMechanical Engineers. ~
No reproduction may be made of this material without written consent of ASME. ~
ASME 816 COMMITTEE
Standardization of Valves, Flanges,
Fittings, and Gaskets
(The followlng is the roster of the Committee at the tlme of approvai of thls Standard.)
STANDARDS COMMITTEE OFFICERS

W. B. Bedesem, Chair
M. L. Nayyar, VIce Chair
D. R. Sharp, Secretary
STANDARDS COMMITTEE PERSONNEL

R. W. Barnes, ANRIC Enterprlses, lnc. G. A. Jolly, Vogt Valves/Fiowserve
W. B. Bedesem, ExxonMobil Research & Engineering Co. M. Katcher, Haynes lntematlonal
D. F. Bucclcone, Elkhart Products Corp. W. N. Mclean, B&L Engineering
A. M. Cheta, Shell Westhollow Techno\ogy Center T. A. McMahon, Fisher Controls lnternational, In c.
M. L. Nayyar, Bechtel Power Corp.
M. Clark, NIBCO, lnc.
J. D. Page, U.S. Nuclear Regu\atory Commission
G. A. Cuccio, Capitai Manufacturing Co. W. H. Patrlck, The Dow Chemical Co.
C. E. Davtla, Crane Valves R. A. Schmldt, Hackney ladish, lnc.
C. E. Floren, Mueller Co. D. R. Sharp, The American Society of Mechanlcal Englneers
D. R. Frlkken, Becht Engineering Co. H. R. Sonderegger, Anvillnternatlonal, lnc.
R. P. Grlfflths, U.S. Coast Guard W. M. Stephan, Aexitallic LP
M. L. Henderson, TIEC, lnc. D. A. Wllllams, Southern Company SeiVices
SUBCOMMITTEE N - STEEL VALVES

W. N. McLean, Chair, B&l Engineering G. A. Jolly, Vogt Valves/FlowseiVe
T. A. McMahon, Vice Chair. Flsher Controls lnternatlonal, In c. M. Katcher, Haynes international
A. P. Maslowskl, Secretary, The American Society of Mechanical M. L. Nayyar, Bechtel Power Corp.
Engineers J, D. Page, U.S. Nuclear Regulatory _Commission
R. W. Barnes, ANRIC Enterprises, lnc. G. J, Paptzun, Consultant
W. H. Patrlck, The Oow Chemlca\ Co.
W. B. Bedesem, ExxonMobll Research & Engineering Co.
D. W. Rahol, CCM 2000
R. A. Benfamln, Northrop Grumman Corp. R. w. Rapp, Consultant
T. R. Brooks, Consultant H. R. Sonderegger, Anvll lnternatlonal, lnc.
C. E. Davila, Crane Va\ves J, P. Tucker, Flowse!Ve
D. R. Frlkken, Becht Engineering Co. ). T. Whlte, PSNSY & IMF
C. L. Henle_y, 8\ack & Veatch M. M. Zaldl, Jacobs
v
Copyright © 2009 by the American Society of Mechanicai Engineers. ~
No reproduction may be made ofthis materia! without written consent of ASME. ~
CORRESPONDENCE WITH THE 816 COMMITTEE
Generai. ASME Standards are developed and maintained with the intent to represent the
consensus of concerned interests. As such, users of this Standard may interact with the Committee
by requesting interpretations, proposing revisions, and attending Committee meetings. Corre-
spondence should be addressed lo:
Secretary, B16 Standards Committee
The American Society of Mechanical Engineers
Three Park Avenue
New York, NY 10016-5990
As an alternative, inquiries may be submitted via e-mail to: SecretaryB16@asme.org.
Proposlng Revlslons. Revisions are made periodically to the Standard to incorporate changes
that appear necessary or desirable, as demonstrated by the experience gained from the application
of the Standard. Approved revisions will be published periodically.
The Committee welcomes proposals for revisions to this Standard. Such proposals should be
as specific as possible, citing the paragraph number(s), the proposed wording, and a detailed
description of the reasons for the proposal, including any pertinent documentation.
lnterpretatlons. Upon request, the 616 Committee will render an interpretation of any require-
ment of the Standard. Interpretations can only be rendered in response to a written request sent
to the Secretary of the 616 Standards Committee.
The request for interpretation should be clear and unambiguous. It is further recommended
that the inquirer submit his/her request in the following format:
Subject: Cite the applicable paragraph number(s) and the topic of the inquiry.
Edition: Cite the applicable edition of the Standard for which the interpretation is
being requested.
Question: Phrase the question as a request for an interpretation of a specific requirement
suitable ·far generai nnderstanding and use~ not as a request for an approvai
of a proprietary design or situation. The inquirer may also include any plans
or drawings that are necessary to explain the question; however, they should
not contain proprietary names or information.
Requests that are not in this fermat will be rewritten in this fermat by the Committee prior
to being answered, which may inadvertently change the intent of the originai request.
ASME procedures previde for reconsideration of any interpretation when or if additional
information that might affect an interpretation is available. Further, persons aggrieved by an
interpretation may appeal to the cognizant ASME Committee or Subcomrnittee. ASME does not
"approve,~~ Certify,~~ rate, or "endorse" any item, construction~ proprietary device, or activity.
11 11 11
Attendlng Commlttee Meetlngs. The B16 Standards Committee regularly holds meetings, which
are open to the public. Persons wishing to attend any meeting should contact the Secretary of
the 616 Standards Committee.
vi
Copyright © 2009 by the American Society of Mechanical Engineers. &Eb
ASME 816.10·2009
FACE-TO-FACE AND END-TO-END

DIMENSIONS OF VALVES
1 SCOPE 1.3 Cast lron Valves

1.1 Generai Only flanged end valves (and others intended for
assembly between flanges) are covered by this Standard.
1.1.1 Applicatlon. This Standard covers face-to-face Matlng dimensiona and faclngs of flanged ends conform
and end-to-end dimensions of straightway valves, and to those In ASME 816.1. Dimensionai tables for various
center-to-face and center-to-end dimensions of angle types and sizes of valves are specified In paras. 1.3.1
valves. Its purpose is to ensure installation interchange- through 1.3.4.
ability for valves of a given material, type, size, rating
class, and end connection. Face-to-face and center-to- 1.3.1 Gate, Plug, and Check Valves
face dimensiona appl y to flanged end valves with facings (a) Class 125 - Tables l and l-1
deflned in para. 2.3.1 and to other valves Intended for (b) C!ass 250 - Tables 2 and I-2
assembly between flat face or raised face flanges. End- 1.3.2 Globe and Angle Valves
lo-end dimensiona apply to grooved end, buttweldlng (a) C!ass 125 - Tables l and l-1
end, and flanged end valves with facings deflned In (b) C!ass 250 - Tables 2 and l-2
para. 2.3.3. Center-to-end dimensiona apply to buttweld-
ing end and lo flanged end valves with faclngs deflned 1.3.3 Wafer Swlng Check Valves
in para. 2.3.3. (a) C!ass 125 - Tables 7 and !4
(b) C!ass 250 - Tab!es 7 and l-7
1.1.2 Data Source Reference. Throughout this
Standard, data references are cited, e.g., "extracted 1.3.4 BuUerfly Valves
from" and "compatible with.u These data are relevant (a) Class 25 - Tables 8 and I-8
to the reference standard in piace at the date shown in (b) C!ass 125 - Tables 8 and l-8
the Foreword for American National Standards lnstitute
approvai of this Standard. 1.4 Ductlle lron Valves
Only flanged end valves (and others intended for
1.2 Standard Unlts assembly between flanges) are covered. Matlng dimen-
The values stated in either millimeter units (Tab!es 1 sions and facings of flanged ends conform to those in
through 10) or lnch units1 (Tables I-1 through l-10) are ASME 816.42. Valves are rated Class 150 and Class 300.
to be regarded separately as standard. Within the text, The fol!owing cast iron and steel dimensionai tables are
the inch units are shown in parentheses. The values also used for ductile valves:
stated in each system are not exact equivalents; there- (a) C!ass 150 - Tables 1 and l-1
fore, each system must be used independently of the (b) Class 300 - Tables 2 and l-2
other. Combining values from the two systems may
result in nonconformance with the standard. 1.5 Steel and Alloy Valves
This category includes carboni alloy, and stainless
1
Linear inch dimensions in this Standard are expressed using steels, and the nonferrous materials listed in
two-place decimai fractions. These values are actually common ASME 816.34. It includes flanged, buttwelding, and
fractions of an inch rounded to the nearest two-piace decimai value grooved ends, as well as the types of valves intended
as follows:
for assembly between flanges. Mating dimensions and
0.03 = ~2 0.44 = 'lt6 facings of flanged ends conform to those In ASME B16.5,
0.06 = Yt6 0.50 = '1., ASME Bl6.47, Series A, or MSS SP-44. [For flanged end
0.12 =~ 0.56 = ~6 butterfly valves, refer to Note (2) of Table 8 (Table I-8)
0.16 = ~2 0.62 =% for flange information.] For flangeless or wafer valves
0.19 = ~6 0.69 = 1 ~6
0.22 = ~2 0.75 =% intended for assembly between flanges, refer lo Tables 7
0.25 = ~ 0.88 = 'ls and 8 (Tables I-7 and l-8) for flange lnformation. Only
0.31 = ~6 0.94 = 1 ~6 buttweldlng end valves in ratlng Classes 150 through
0.38 =% 2500 are included In this Standard. Dimensionai tables
l
Copyright © 2009 by the American Society of Mechanical Engineers. dih
ASME 816.10·2009
for various types and sizes of valves are specified in NPS DN

paras. 1.5.1 lhrough 1.5.5. ~ 8
1.5.1 Gate, Globe, Angle, Check, Plug, and Bali
l'a 10
Y, 15
Valves '!,; 20
(a) Class 150 - Tab!es 1 and I-1 l 25
(b) Class 300 - Tab!es 2 and I-2 l~ 32
l~ 40
(c) Class 600- Tables 3 and l-3 2 50
(d) Class 900 - Tables 4 and I-4 2~ 65
(e) Class 1500 - Tables 5 and I-5 3 80
4 100
(/) Class 2500 - Tables 6 and I-6
GENERAL NOTE: For NPS;;?: 4, the related DN = 25 multiplied by the
1.5.2 Y-Pattern Globe and Y-Pattern Swlng Check NPS number.
Valves 2.1.3 Reduced Por! Valves
Class 150 - Tables l and I-1 Reduced pori, gate, and bali valves conforming to
(a)
API 60 are designated for size by two numbers, the first
1.5.3 Wafer Knlfe Gale Valves being the NPS on the valve ends, the second being the
Class 150 - Tables 7 and I-7 NPS of the port (seats, moving parts, etc.); e.g., NPS 6
1.5.4 Wafer Swlng Check Valves x 4 designates a valve of end size NPS 6 with a port to
Class 150 lo 2500 - Tables 7 and I-7 match NPS 4. These valves shall have face-to-face or
end-to-end dimensions corresponding to valves having
1.5.5 Butterfly Valves the same size end connections; i.e., a NPS 6 x 4 valve
(a) Class 150 - Tables 8 and i-8 shall have the face-to-face or end-to-end dimensions of
(b) Class 300 - Tables 8 and l-8
a NPS 6 valve.
(b) Reduced por!, pressure seal bonnet, gate, globe,
(c) C!ass 600 - Tables 8 and I-8
and check valves are designated for size by three num-
bers, the first and last being the NPS of the valve ends,
1.6 Conventlon the second being the NPS of the port; e. g., NPS 6 x 4 x 6
Por the purpose of determining conformance with designates a valve having ends matching NPS 6 with a
this Standard/ the convention for fixing significant digits port to match NPS 4. Likewise, NPS 6 x 4 x 4 would
where limits, maximum or minimum values1 are speci- designate a valve having one end matching NPS 6, the
fied, shall be "rounding off" as defined inASTM Practice other matching NPS 4, and the port matching NPS 4.
E29. This requires that an observed or calculated value These valves shall have face-to-face or end-to-end
shall be rounded off lo lhe nearesl unii in lhe !asl dimensions corresponding to valves having the same
right-hand digil used for expressing the limit. Decimai pori size; i.e., either a NPS 6 x 4 x 6 or a NPS 6 x 4 x 4
values and tolerance do not imply a particular method valve shall have the face-to-face or end-to-end dimen-
of measurement. sions of a NPS 4 valve.
2.2 Pressure Rating Designatlons
Class, followed by a dimensionless number, is the
2 DEFlNITIONS standardized designation for pressure temperature-
ratings used for valves. The numerica} designations in
2.1 Valve Slze Designation use are as follows:
(a) for cast iron: 25, 125, 250
2.1.1 Nominai Dlameter (DN). The size of a valve is
(b) for ductile iron: 150, 300
designateci by the nominai size of its end connections.
(c) for steel: 2 150, 300, 600, 900, 1500, 2500
This is denoled by (DN), a dimensionless number indi-
rectly related to the physical size of the connecting pipe 2.3 Flanged Valve Dlmensions
[See Tables l through 10 (Tables I-1 through I-10)]. The
valve size is no t necessarily the same as the inside diame- 2.3.1 Face·to·Face. The face-to-face dimension for
ter or port diameter. flanged valves is the distance between the extreme ends
which are the gasket contact surfaces (see Fig. 1). Face-
2.1.2 Valve Slze Deslgnatlon. NPS, followed by a to-face applies to flanged valves having the following
dimensionless number, is the designation for nominai nominai flange facing identifiers:
valve size. NPS is related to the reference nomina[ diame- (a) flat
ters, DN, used in international standards. The relation-
2
ship is, typically, as follows: Indudes ali ferrous and nonferrous materials in ASME 816.34.
2
ASME 816.10·2009
(b) 2 mm (0.06 in.) raised required with flat laces, either the full thickness ol flange
(c) 7 mm (0.25 in.) raised or the thickness with the 2 mm (0.06 in.) raised lace
(d) large or small male3 removed may be furnished~ unless otherwise specified
(e) large or small tongue3 by the customer. Users are reminded that removing the
2 mm (0.06 in.) raised lace will make the lace-to-lace
2.3.2 lnstalled Face-to-Face. The installed lace-to- dimension nonstandard.
lace dimension ol certain butterfly valves [see Table 8
(Table 1-8), Note (6)] may include allowances lor gasket 3.1.3 7 mm (0.25 In.) Ralsed Face. Flanges lor
or resilient-lacing compression. Reler to MSS SP-67 lor Class 600 and higher steel and alloy valves have 7 mm
definitive illustrations. (0.25 in.) raised laces, which are included in the lace-
to-face (or center-to-face) dimensions.
2.3.3 End-to-End. For those flanged valves where
the gasket contact surfaces are not located at the extreme 3.2 Other Standard Faclng$
ends of the valve, the distance between the extreme ends Table 9 (Table 1-9) summarizes data on al! flange lac-
is descr'ibed as the end-to-end dimension and applies ings and can be used with Tables l through 6 (Tables 1-1
to flanged valves having the lollowing nomina! flange through 1-6) in calculating lace-to-lace and end-to-end
facing identifiers:
dimensions ol flanged valves having standard lacings
(a) ring joint
other than those described in para. 3.1.
(b) large or small Iemale
(c) large or small groove 3.3 Rlng Jolnt Faclngs
2.4 Buttweldlng End Valve Dlmenslons The X dimension given in Table lO (Table 1-10), when
added to the face-to-face dimension of a valve having
For buttwelding end valves, the end-to-end dimension raised lace flanges in Tables l through 6 (Tables 1-1
is the distance between the extreme ends (root faces) of through 1-6), establishes the end-to-end dimension lor
the welding bevels (see Fig. 2). the valve having flanges with ring joint lacings.
Also see section 4.
2.5 Grooved End Valve Dimenslons 4 VARIATIONS OF LENGTH WlTHIN A CLASS OF
The end-to-end dimension for grooved end valves is VALVES
the distance between extreme ends. 4.1 Buttweldlng End Valves
2.6 Angle Valves Tables l through 6 (Tables I-1 through 1-6) include
end-to-end dimensions for valves having buttwelding
For flanged angle type valves (those in which the ends
ends. In many cases~ the dimensions are different from
are at an angle ol 90 deg to each other), the center-to-
those of face-to-face dimensions of flanged valves~ as
face dimension is the distance from the centerline of the evidenced by the differences between dimensions A and
port to the extreme end which is the gasket contact B ol the tables.
surface. Por flanged angle type valves in which the gas-
Also see para. 2.4.
ket seating surface is not located at the extreme end
and lor angle type valves having buttwelding ends, the 4.1.1 Short Pattern. For pressure seal or flangeless
phrase center-to-end denotes the distance from the cen- bonnet valves having buttwelding ends in Class 600 and
terline of the port to the extreme end. higher, the regular end-to-end dimensions shall be equa!
to the short pattern dimensions shown in Tables 3
through 6 (Tables 1-3 through 1-6). At the manulacturer's
3 FACINGS OF FLANGED VALVES
option~ the end-to-end dimensions of these valves may
Figure l shows lacings lor flanged ends. be the same as the face-to-face dimensions of raised face
flanged valves.
3.1 Faclngs Normally Furnlshed
4.1.2 Long Pattern. For flanged bonnet valves hav-
3.1.1 Flat Face. Flanges lor Classes 25 and 125 cast ing buttwelding ends in Class 600 and higher, the regular
iran valves are flat faced. end-to-end dimensions shall be equal to the face-to-face
3.1.2 2m m (0.061n.) Ralsed Face. Flanges lor Class dimensions of raised face flanged val ves shown in
250 cast iron and lor Classes 150 and 300 steel, alloy, Tables 3 through 6 (Tables 1-3 through 1-6). At the manu-
and ductile iron valves have 2 mm (0.06 in.) raised faces~ facturer~s option~ the end-to-end dimensions may be the
which are inciuded in the lace-to-lace (or center-to-lace) same as the short pattern end-to-end dirnensions.
dimensiol). When Classe$ 150 and 300 valves are
4.2 Narrow, Wlde, and Extra Wide Designations
3
Face-to-face dimensions in Tables l through 6 (Tables I-l Certain butterfly valves are designated narrow, wide,
through 1-6) must be adjusted as indicated in Table 9 (Table 1-9). or extra wide for the purpose of consolidating a diversity
3
No reproduction may be made ofthis material without written Consent of ASME. ~
ASME B16.10·2009
of manufacturer's lengths into two or three sets of NPS 10 and smaller, and a tolerance of ±3 mm (±0.12 in.)
dimensions for a given size. At the manufacturer's shall be allowed for NPS 12 and larger. For exceptions as
option, any of the two or three dimensions listed for a related to wafer type and butterfly valves, see Generai
size may be used. Note (b) in Table 7 (Table I-7) and Notes (3) and (4) in
Table 8 (Table I-8).
5 TOLERANCES
5.2 Angle Valves
5.1 Stralghtway Valves The tolerances on center-to-face and center-to-end
A tolerance of ±2 mm (±0.06 in.) shall be allowed dimensions of angle type valves shall be one-half those
on face-to-face and end-to-end dimensions of valves of listed in para. 5.1.
4
ASME 816.10·2009
Fig. 1 Flange Facings and Thelr Relatlonships

Basic flange edge to flange edge Basic flange edge to flange edge
/
. .Face~to-face dimension given in the tables
Flat Face
' ...
7mm
(0.25 in.)
Face-to-face dimension
Large or Small
Male Face
Regular facing on
Class 125 cast iran
Far steel va/ves anly
(Note (111
l
l Basic flange edge to flange edge Basic flange edge to flange edge
Face-to-fa ce dimension given in the tables Face-ta-fa ce dimension
2
1~~ in.)j~mm
5mm
~
(0.19 in.) Large or Small
(0.06 in.) Raised Face
Female Face
Regular facing on
Class 250 cast iran For steel va/ves only
l and Classes 150 and
300 steel (Note (111
[Note (1))
l l
Basic flange edge to flange edge Basic flange edge ta flange edge
Face-to-fa ce dimension given in the tab/es Face-ta-face dimensian

7mm
[1
7mm
(0.25 in.) mm (0.25 In.) Raised Face (0.25 in.) Larga or Small
Tcmgue
Regular facing o n
Class 600 and higher Far steel va/ves anly
steel valves [Note (1 )] [Note (111
l
l l
Basic flange edge to flange edge Basic flange edge to flange edge
End-to-end dimension [see Table 10 (Table 1-10)] End-to-end dimensian

Depth of 5mm
groove RingJoint (0.19 in.) Larga or Small
Groove
Facing far steel

valves only [Note (111 Facing far steel
va/ves anly [Note (1)]
(a) Regular Standard Facings (b) Other Standard Facings

[Note (211 [Note [311
NOTES:
(1) Steellncludes nonferrous materials In ASME 816.34.
(2) Regular flange facings for va/ves are shown above. Va/ves normally carri ed In stock are so faced.
(3) Valves are supplied with the faclngs shown above when speclfled. See Table 9 (Table 1-9) to determine face-to-face dimensions of
valves with these facings.
5
No reproduction may be made afth,is material without written consent of ASME. ~
ASME 616.10·2009
Fig. 2 Welding Ends
~-Rootface
End-to-end dimension
~ ......
End-to-end dimension
(al Plaln Bevel (b) Compound Bevel

GENERAL NOTE: Typical bevels are shown far lllustratlon only.
6
Copyright © 2009 by the Arnerican Society of Mechanical Engineers. dib
No reproduction may be made of this material without w ritten consent of ASME. ~
ASME 616.10·2009
Table 1 Class 125 Cast lron Flanged and Class 150 Steel. Flanged an d Buttwelding End Valves,
Face-to-Face and End-lo-End Dimensions
Pia in face Raised face Buttwelding end
'· A
·' ~A~ B~
Class 125 Cast lron Class 150 Steel Class 150 Steel
1 2 3 4 5 6 7 8 9 10
Class 125 Cast Jron Class 150 Steel
Flanged End (2 mm Ralsed Fate}
Flanged End (Fiat Face) and Weldlng End
Gate, Plug Gate Plug

Soli d Globe, Soli d Soli d
Wedge Regular Llft Check, Wedge Wedge,
an d an d Round and Swlng Angle and an d Double
Nominai Double Short Venturi Port, Check Llft Double Disc, and Short
Valve Slze Disc, Pattern, Pattern, Full Bore, [Note (1)), Check, Disc, Condult, Condult, Pattern,
NPS _l DN A A A A A o A A 8 A
'1. 8 102 102

% 10 102 102
'h 15 108 108
% 20 117 117
1 25 140 140 (2) 140 127 127 140
t% 32 165 (2) 152 140 140

tlf2 40 165 165 (2) 165 165 165 165
2 50 178 178 190 (2) 190 203 102 178 178 216 178
2~ 65 190 190 210 (2) 210 216 108 190 190 241 190
3 so 203 203 229 (2) 229 241 121 203 203 282 203
4 100 229 229 229 (2) 305 292 146 229 229 305 229
5 125 254 254 356(2) 381 330 165 254 381 254
6 ISO 267 267 394 457 356 178 267 267 403 267
8 200 292 292 457 559 495 248 292 292 419 292
10 250 330 330 533 660 622 311 330 330 457 330
12 300 356 356 610 762 698 349 356 356 502 356
14 350 381 (3) 686 787 394 381 381 572
16 400 406 (3) 762 914 (4) 457 406 406 610
18 450 432 (3) 864 432 432 660
20 500 457 (3) 914 457 457 711
22 550 508 762

24 600 508 (3) l 067 (5) 508 508 813
26 650 559 559 864 (6)
28 700 610 610 914 (6)
30 750 1 295 (5) 610 660 914 (6)
32 800 711 965 (6)

34 850 762 1 016 (6) 1016
36 900 1 600 (5) 711 813 1 016 (6)
7
Copyright© 2009 by the American Society ofMechanical Engineers. ~
ASME 816.10·2009
Table 1 Class 125 Cast lron Flanged and Class 150 Steel Flanged and Buttweldlng End Valves,
Face-to-Face and End-to-End Dlmenslons (Cont'd)
Buttwelding
end
Clàss 125 Cast lron Class 150 Steel Class 150 Steel
11 12 13 14 15 16 17 18 19 20 21
Class 150 Steel
Flanged End (2 mm Raised Face) and Weldlng End Flanged End Weldlng End
Plug Globe, Bali
Llft
Check,
Short an d Y-Giobe
an d Round Swlng Angle and an d
Nominai Regular Regular Venturi Port, Check Llft Long Long
Y·Swing Short Short
Valve Slze Pattern, Pattern, Full Bore, ]Note (1)], Check, Pattern, Pattern, Pattern, Pattern,
Pattern, Check,
NPS l ON A 8 A A A and 8 DandE A and 8 A A 8 8
% 8 102 51
% 10 102 51
'h 15 108 57 140 108 108 140
% 20 117 64 152 117 117 152
1 25 176 127 70 165 127 127 165
tY4 32 140 76 184 140 140 178

1~ 40 222 165 83 203 165 165 190 190
2 so 267 178 267 203 102 229 178 178 216 216
2Y2 65 305 298 216 108 279 190 190 241 241
3 80 330 203 343 241 121 318 203 203 282 282
4 100 305 356 229 432 292 146 368 229 229 305 305
5 125 381 381 356 (7) 178
6 150 394 457 394 406 (7) 203 470 394 267 457 403
8 200 457 521 457 495 248 597 457 292 521 419
10 250 533 559 533 622 311 673 533 330 559 457
12 300 610 635 610 698 349 775 610 356 635 502
14 350 686 686 787 394 686 381 762 572
16 400 762 762 914 (8) 457 762 406 838 610
18 450 864 864 978 (9) 864 914 660
20 500 914 914 978 (9) 914 991 711
22 550 1 067 (9) 1 092

24 600 1067 1067 1 295 (9) 1067 1143 813
26 650 1 295 (9) 1245
28 700 1 448 (9) 1 346
30 750 1 524 (9) 1 397
32 800 1 524
34 850 1 626
36 900 1 956 (9) 1 727
8
Copyright© 2009 by the American Society ofMechanical Engineers. &
ASME 816.10·2009
Table 1 Class 125 Cast lron Flanged and Class 1 SO Steel Flanged and Buttwelding End Valves,
Face-to-Face and End-to-End Dimensions (Cont'd)
GENERAL NOTES,
(a) Dimensions are in mlllimeters.
(b) See Table 9 for adjustments to tabulated dimenslons that may be required for certain flange faclngs.
NOTES:
(1) These dlmenslons are not lntended to cover the type of check valve having the seat angle at appoximately 45 deg to the run of the
valve, or the "Unde!Writer Pattern," or other patterns where large clearances are required.
(2) Regular pattern only. The face-to·face dimenslon of NPS 4 (DN 100) may be 305 at the manufacturer's option.
(3) Solld wedge on!y.
(4) Glebe and horizontallfft check only.
(5) Venturi pattern only.
(6) Double disc and condult only.
(7) Glebe and horlzontalllft check only. The faèe-to-face and end-to-end dimenslan far Class 150 steel flanged and buttwelding end swing
check valves In NPS 5 (DN 125) ls 330 and In NPS 6 (DN 150) Js 356.
(8) Globe and horizantallift check anly. The face·ta-face and end·to·end dimenslon far Class 150 steet flanged and buttweldlng end swlng
check valves In NPS 16 (DN 400) is 864.
(9) Swing check only.
9
Copyright © 2009 by the American Society ofMechanical Engineers. &
ASME 816.10·2009
Table 2 Class 250 Cast lron Flanged and Class 300 Steel Flanged and Buttwelding End Valves,
Face-to-Face and End-to-End Dimensions
Raised face Buttwelding end
Class 250 Cast lron Class 300 Steel

and Class 300 Steel
1 2 3 4 5 6 7 8 9
Class 250 Cast lron C(ass 300 Steel
Flanged End {2 mm Ralsed Fate) Flanged and Weldlng End
Gate, Plug Globe, Bali
Soli d Llft
Wedge Check,
an d an d Angle and
Nominai Valve Double Short Regular Venturi Swlng Llft Long Short Long
Slze Disc, Pattern, Pattern, Pattern, Check, Check, Pattern, Pattern, Pattern,
NPS l DN A A A A A o A A and 8 8
y, 15 140 140
'!. 20 152 152
1 25 159 165 165
t% 32 178 178
t% 40 190 190 190 190
2 50 216 184 216 267 133 216 216 216

2~ 65 241 203 241 292 146 241 241 241
3 BO 282 235 282 318 159 282 282 282
4 100 305 267 305 356 178 305 305 305
5 125 381 387 400 200
6 150 403 378 425 403 444 222 403 403 457
8 200 419 502 419 533 267 502 419 521
10 250 457 568 597 457 622 311 568 457 559
12 300 502 648 711 502 711 356 648 502 635
14 350 572 762 762 572 762
16 400 610 838 838 610 838

18 450 660 914 914 660 914
20 500 711 991 991 711 991
22 550 1118 1092 1092
24 600 787 1143 1 143 813 1143
26 650 1 245 1 245

28 700 1 346 1 346
30 750 1 397 1 397
32 800 1 524 1 524
34 850 1 626 1 626
36 900 1 727 1 727
10
Copyright © 2009 by the American Society of Mechanical Enginecrs. ~
No reproduction may be made of this material without written con sent of ASME. ~
ASME 816.10·2009
Face·to-Face and End-to·End Dlmensions (Cont'd)
Buttwelding
end

and Class 300 Steel
10 11 12 13 14 15 16 17
Class 300 Steel
Flanged End (2 mm Ralsed Face) and Weldlng End
Gate, Plug
Soli d
Wedge,
Double Short
Disc, an d Short and Round Angle
Nominai Valve an d Venturi Venturi Regular Port, Full Gtobe and and Llft Swlng
Size Check,
Condult, Pattern, Pattern, Pattern, Bore, Llft Check, Check,
NPS l DN A and 8 A 8 A A and B A and 8 DandE A and B
\1, 15 140 (1) 152 76

% 20 152 (l) 178 89
l 25 165 (1) 159 (2) 190 203 102 216
t% 32 178 (1) 216 108 229
1~ 40 190 190 (2) 241 229 114 241
2 50 216 216 267 (2) 282 267 133 267

2% 65 241 241 305 (2) 330 292 146 292
3 80 282 282 330 (2) 387 318 159 318
4 100 305 305 356 (2) 457 356 178 356
5 125 381 400 200 400
6 150 403 403 457 403 559 444 222 444

8 200 419 419 521 502 686 559 279 533
10 250 457 457 559 568 826 622 311 622
12 300 502 502 635 711 965 711 356 711
14 350 762 762 (3) 762 (3) 762 838
16 400 838 838 (3) 838 (3) 838 864

18 450 914 914 (3) 914 (3) 914 978
20 500 991 991 (3) 991 (3) 991 l 016
22 550 1092 l 092 (3) l 092 (3) 1092 1118
24 600 1143 1143 (3) 1143 (3) 1143 1 346
26 650 1 245 1 245 (3) 1 245 (3) l 245 1 346

28 700 1 346 1 346 (3) 1346 (3) 1346 1 499
30 750 1 397 1 397 (3) 1 397 (3) 1 397 1 594
32 800 1 524 1 524 (3) 1 524 (3) 1 524
34 850 1 626 l 626 (3) 1 626 (3) l 626
36 900 1 727 1 727 (3) 1 727 (3) 1 727 2 083
11
No reproduction may be made ofthis materia( without written consent of ASME. ~
ASME 816.10·2009
Face-to-Face and End-to-End Dlmensions (Cont'd)
GENERAL NOTES:
(a) Dimensions are ln millimeters.
(b) See Table 9 for adjustments to tabu\ated dimenslons that may be required for certain flange facings.
NOTES:
(1) Solid wedge only.
(2) Plug- short pattern only.
12
ASME 816.10·2009
Table 3 Class 600 Steel Flanged and Buttwelding End Valves, Face-to-Face and End-to-End Dlmenslons
Buttwelding
end
1 2 3 4 5 6 7 .a 9 10
Class 600 Steel
Flanged End (7 mm Ralsed Face and Weldlng End}
Bali Gate Plug
Solid Globe llft Globe llft
Wedge, Check, Check,
Double an d and Swlng Angle Angle and
Disc, and Regular Swlng Check, and llft llft Check,
Condult, Short an d Round Round Check, Short Check, Short
Nominai long Long Pattern, Venturi Bore, Bore, Long Pattern Long Pattern
Valve Slze Pattern, Pattern, [Note (1)], Pattern, Full Port, FuU Port, Pattern, [Note (1)], Pattern, [Note (1)],
NPS l DN A and 8 A and B 8 A and 8 A 8 A and B 8 DandE E
y, 15 165 165 (2) 165 83
% 20 190 190 (2) 190 95
l 25 216 216 133 216 (3) 254 216 133 108
t% 32 229 229 146 229 (3) 229 146 114
1~ 40 241 241 152 241 318 241 152 121
2 50 292 292 178 292 330 292 178 146 108

2%: 65 330 330 216 330 381 330 216 165 127
3 80 356 356 254 356 444 356 254 178 152
4 100 432 432 305 432 508 559 432 305 216 178
5 125 508 381 508 381 254 216
6 150 559 559 457 559 660 711 559 457 279 254
8 200 660 660 584 660 794 845 660 584 330
lO 250 787 787 711 787 940 l 016 787 711 394
12 300 838 838 813 838 l 067 l 067 838 813 419
14 350 889 889 889 889 889 (4)
16 400 991 991 991 991 991 (4)

18 450 l 092 l 092 1092 l 092 (5) l 092 (4)
20 500 1194 1194 1194 1194 (5) 1194 (4)
22 550 l 295 l 295 l 295 (5) l 295 (4)
24 600 l 397 l 397 1397 l 397 (5) l 397 (4)
26 650 1448 1448 l 448 (5) l 448 (4)

28 700 l 549 l 549 l 600 (4)
30 750 1 651 l 651 l 651 (5) l 651 (4)
32 800 l 778 l 778 (6) l 778 (5)
34 850 l 930 l 930 (6) l 930 (5)
36 900 2 083 2 083 (6) 2 083 (5) 2 083 (4)
13
Copyright © 2009 by thc American Society ofMechanical Engineers. ~
ASME 816.10·2009
Table 3 Class 600 Steel Flanged and Buttweldlng End Valves, Face-to-Face and
End-to-End Dlmenslons (Cont'd)
GENERAL NOTES:
(a) Dim~nsions are in millimeters.
(b) See Table 9 far adjustments to tabulated dimenslons that may be required for certain flange facings.
NOTES:
(1) These dimenslons apply to pressure seal or flangeless bonn et valves. They may be aPplied at the manufacturer's optlon to valves wlth
flanged bonnets.
(2) Soljd wedge only.
(3) Regular pattern only.
(6) Double disc and conduit only.
14
ASME 816.10·2009
Table 4 Class 900 Steel Flanged and Buttwelding End Valves, Face-to-Face and End-to-End Dimenslons
Buttwelding
end
l 2 3 4 5 6 7 8 9
Class 900 Steel
Gate Plug .Bali
Solid Globe llft
Wedge, Globe llft Check,
Double Check, an d
Disc, an d Swlng Angle Angle and
an d Regular Swing Check, and llft llft Check,
Condult, Short an d Round Check, Short Check, Short
Nominai Valve Long Pattern, Venturi Port, Long Pattern long Pattern Long
Slze Pattern, [Note (1)1, Pattern, Full Bore, Pattern, [Note (1)1, Pattern, [Note (1)1, Pattern,
NPS l DN A and 8 8 A and B A A and B 8 DandE E A and B
';. 20 (2) 229 114
1 25 (2) 254 (3) 140 254 (4) 254 127 254
t% 32(2) 279 (3) 165 279 (4) 279 140 279
t% 40 (2) 305 (3) 178 305 (4) 356 305 152 305
2 so (2) 368 216 368 (4) 381 368 184 368
2% 65 (2) 419 254 419 (4) 432 419 254 210 419
3 80 381 305 381 (4) 470 381 305 190 152 381
4 100 457 356 457 (5) 559 457 356 229 178 457
5 125 559 432 559 432 279 216
6 150 610 508 610 737 610 508 305 254 610
8 200 737 660 737 813 737 660 368 330 737
IO 250 838 787 838 965 838 787 419 394 838
12 300 965 914 965 1118 965 914 483 457 965
14 350 l 029 991 l 029 991 514 495 1 029
16 400 1130 1092 1130 (5) l 130 (6) l 092 660 1130
18 450 l 219 l 219 (6) 737 1 219

20 500 l 321 1 321 (5) 1 321 (6) 826 1 321
22 550
24 600 1 549 l 549 (6) 991 l 549
GENERAl NOTES:
(a) Dlmenslons are In millimeters.
(b) See Tab\e 9 for adjustments to tabulated dimenslons that may be required for certain flange facings.
NOTES:
(1) These dimenslons apply to pressure seal or flangeless bonn et valves. They may be applied at the manufacturer's option to valves wlth
flanged bonnets.
(2) The connectlng end flanges for ctass 900 valves, NPS 2% (DN 65) and smaller, are identica! to those of Class 1500 valves. The face-
to-tace dimensions forali Class 900 valves, NPS i% (DN 65) and smaller, except round port full bore plug valves (column 4), are iden-
tica! with those of Class 1500 valves.
15
Copyright © 2009 by the American Society ofMechanical Engineers. &
No reproduction may be m ade of this material without written consent of ASME. ~
ASME 816.10·2009
Table 5 Class 1500 Steel Flanged and Buttweldlng End Valves, Face-to-Face and End-to-End Dimensions
Buttwelding
Raised tace Buttwelding end end
1 2 3 4 5 6 7 8
Class 1500 Steel
Ftanged End (7 mm Ralsed Face) and Weldlng End
Gate Plug Bali
Soli d Globo Llft
Wedge, Globo Llft Check,
Double Check, an d
Disc, an d Swlng Angle
an d Regutar Swlng Check, and Llft
Nominai
Condult, Short an d Round Check, Short Check,
Valve Long Pattern, Venturi Port, Long Pattern Long Long
Slze Pattern, [Note (1)[, Pattern, Full Bore, Pattern, [Note (1)[, Pattern, Pattern,
NPS _/ DN A and 8 8 A and 8 A A and B 8 DandE A and 8
y, 15 216 (2) 108
% 20 229 114
1 25 254 (3) 140 254 (4) 254 127
t%
1
32 279 (3) 165 279 (4) 279 140
1 /2 40 305 (3) 178 305 (4) 305 152
2 50 368 216 368 (4) 391 368 216 184 368

2% 65 419 254 419 (4) 454 419 254 210 419
3 80 470 305 470 (4) 524 470 305 235 470
4 100 546 406 546 (4) 625 546 406 273 546
5 125 673 483 673 483 337
6 150 705 559 705 787 705 559 353 705

8 200 832 711 832 889 832 711 416 832
IO 250 991 864 991 l 067 991 864 495 991
12 300 1130 991 1130 1 219 1130 991 565 1130
14 350 1 257 l 067 1 257 l 067 629 1257
16 400 1 384 1194 l 384 (5) l 384 (6) 1194 1 384

18 450 1 537 1346 l 537 (6)
20 500 1 664 l 473 l 664 (6)
22 550
24 600 1 943 1 943 (6)
16
ASME 816.10·2009
Table S Class 1500 Steel Flanged and Buttwelding End Valves, Face-to-Fate and
End-to-End Dimensions (Cont'd)
GENERAL NOTES,
(a) Dimenslons are in millimeters.
(b) See Tab\e 9 far adjustments to tabulated dlmensions that may be required for certa in flange faclngs.
NOTES'
(1) These dlmenslons apply to pressure seal or flangeless bonnet valves. They may be applied at the manufacturer's optlon to valves wlth
flanged bonnets.
(2) Globe and IIft check only.
(3) Solld wedge only.
(6) Swlng check only.
17
Copyright© 2009 by the American Society ofMechanical Engineers. &
,.
t '.
l
ASME 816.10-2009
Thble 6 Class 2500 Steel Flanged and Buttwelding End Valves, Face-to-Face and End-to-End Dlmensions
Buttwelding
Raised face Buttwelding end end
1 2 3 4 5 6 7
-
Class 2500 Steel
Gate Bali
Soli d Globe Globo Llft
Wedge, Llft Check,
Double Check, an d
Disc, an d Swlng Angle
an d Swlng Check, and Llft
Nominai Conduit, Short Plug Check, Short Check,
Valve Long Pattem~ Regular Long Pattern Long long
Slze Pattern, Pattern, [Note (1)], Pattern, Pattern,
P!ittern, [Note (1)1,
NPS l DN A and B 8 A and 8 A and 8 8 o andE A and 8
y, 15 264 (2) 264 132
'Y. 20 273 (2) 273 137
1 25 308 (2) 186 308 308 154
t% 32 349 (2) 232 349 175
l~ 40 384 (2) 232 384 384 192
2 50 451 279 451 451 279 226 451
2% 65 508 330 508 508 330 254 508

3 80 578 368 578, 578 368 289 578
4 100 673 457 673 673 4.57 337 673
5 125 794 533 794 794 533 397
6 150 914 610 914 914 610 457 914
8 200 1 022 762 l 022 l 022 762 511 1 022
lO 250 l 270 914 l 270 l 270 914 635 1 270

12 300 l 422 1 041 1422 l 422 l 041 711 1 422
14 350 1118
16 400 1 245
18 450 1 397
GENERAL NOTES:
(a) Dimensions are In millimeters.
(b) See Table 9 far adjustments to tabulated dimensions that may be required for certa in flanged faclngs.
NOTES:
(1) These dimensions apply to pressure sea\ or flangeless bonnet valves. They may be applied at the manufacturer's option to valves with
flanged bonnets.
18
Table 7 Classes 125 and 250 Cast lron and Classes 150 to 2500 Steel Wafer Type Valves, Face-to·Face Dimensions
1 2 l 3 4 l 5 l 6 l 7 l 8 l 9 10 l 11 l 12 l 13 l 14
Steel [Note (1)] Cast lron [Note (2)]
Swing Check. Swing Check. Single and Dual Plate, lnstaltation Between Standard ANSI Ranges
Single and Dual Plate, [Note (3)]
~ lnstallation Between
.ga.,Q Nominai
Bonnetless
Knife Gate,
Standard ANSI Aanges Class Class
g~.
g- ::;-
Valve
Size
Class 150
Flange Mating
Class 150 l 300 l 600 l 900 l 1500 l 2500 150 l 300 l 600 l
900 l 1500
~@
3 N
NPS l DN Dimensions 125 l 250 Long Pattern [Note (4)] Short Pattem [Note (5)]
~o 2 50 48 54 54 60 60 60 70 70 70 19 19 19 19 19
g"~
3~
2% 65 " . 60 60 67 67 67 83 83 83 19 19 19 19 19
3 80 51 67 67 73 73 73 83 83 86 19 19 19 19 22
~~
o o 4 100 51 67 67 73 73 79 102 102 105 19 19 22 22 32
o> 5 125 57 83 83
:::'3 6 150 57 95 95 99 99 137 159 159 159 19 22 28 35 44
~ 9. >
3 g
= ~
1>"'
~. o
a g_l te
8
10
200
250
70
70
127
140
127
140
127
146
127
146
165
213
206
241
206
248
206
254
28
28
28
38
38
57
44
57
57
73
.'"
s:
m
~
:g_q 12 300 76 181 181 181 181 229 292 305 305 38 51 60 " . ". "'
;..
o
S'o
14 350 76 184 222 184 222 273 356 356 ." 44 51 67 " . ". ,:,
o ..., 16 400 89 190 232 190 232 305 384 384 ". 51 51 73 ." " . o
o
~;;:: 18 450 89 203 264 203 264 362 451 468 " . 60 76 83 "'
~- ~
"o ~-·o
~
20
24
500
600
114
114
213
222
292
318
219
222
292
318
368
438
451
495
533
559
". 64 83 92
8 a 368 305 368 505
i;; ~ 30 750 ". 305
-
g re.
o o~
...,o
36
42
900
1050
."
" .
368
432
483
568
368
432
483
568
635
702
>~ 48 1200 ." 524 629 524 629
~ GENERAl NOTES'
(a) Oimensions are in millimeters.
~
(b) The tolerances of para. 5.1 appty to face-to-face dimensions for sizes NPS 24 (DN 600) and smaller. For sizes NPS 30 (DN 750) an d larger, the tolerance shall be ±6 mm.
NOTES'
(1) These data are extracte'd from MSS SP-81 that covers non-Class designated (Le., cold working pressure) rated for 150°F (66°0 maximum knife gate vaives that have ASME 816.5,
Class 150 flange bolting templates.
(2) These data for cast iron swing check va\ves are extracted from API 594.
(3) Valves of sizes NPS 30 (DN 750) and larger in ctasses 150, 300, and 600 shall have body outside diameters an d gasket surface dimensions compatible with flange standards speci~
fied in the purchase order, e.g., ASME 816.47 Sr. 8 or ASME 816.47 Sr. A (MSS SP-44).
(4) These data for long pattem steel swing check valves in sizes NPS 24 (DN 600) and smaller are extracted from API 60 and API 594. Data for larger sizes are extracted from API 594.
(5) These data for short pattem steel swing check valves are extracted from API 60.
ASME 816.10·2009
Table 8 Classes 25 and 125 Cast lron and Classes 150 to 600 Steel Butterfly Valves, Face-to-Face
Dimenslons
1 l 2 3 l 4 l 5 6 7 8 9
Steel
Grooved End Steel Offset Seat
Class 150 Cast lron and Steel {Notes (1}, Lug and Wafer Style
{Notes (1), (2}, and (3}] (3)] {Notes (4), (5)]
Nominai Valve
Slze Flanged End Lug and Wafer Style {Note (6)]
Class Class Class Class
NPS l DN Narrow _l Wlde Narrow J Wlde J Extra Wide 150 150 300 600
1t;2 40 33 37 38 86
2 50 43 44 46 81
2% 65 46 49 51 97
3 80 127 127 46 49 51 97 48 48 54
4 100 127 178 52 56 57 116 54 54 64
5 125 127 190 56 64 65 148
6 150 127 203 56 70 71 148 57 59 78

8 200 152 216 60 71 75 133 64 73 102
10 250 203 381 68 76 79 159 71 83 117
12 300 203 381 78 83 86 165 81 92 140
14 350 203 406 78 92 95 178 92 117 155
16 400 203 406 79 102 105 178 102 133 178
18 450 203 406 102 114 117 203 114 149 200
20 500 203 457 111 127 130 216 127 159 216
24 600 203 457 154 157 254 154 181 232
30 750 305 559 165
36 900 305 559 200
42 l oso 305 610 251
48 1 200 381 660 276

54 l 350 381 711
60 l 500 381 762
66 1 650 457 864
72 l 800 457 914
GENERAL NOTE: Dlmenslons are In mlllimeters.

NOTES:
(1) These butterfly valves are of the design generally havlng concentric locatlon of disc and seat, covered by MSS SP-67, from whlch these
data are extracted.
(2) These valves are dimenslonal\y compatlble with flanges conformlng to ASME 816.1 Class 25 or Class 125, ASME 816.5 Class 150,
ASME 816.24 Class 150, ASME 816.42 Class 150, or AWWA C-207.
(3) For these butterfly vatves, a tolerance of ±2 mm shall be allowed o n face·to·face dimenslons of valves of NPS 6 (DN 150) and smaller,
and a tolerance of ±3 mm on NPS 8 (ON 200) and larger, except that for single flange an d flangeless valves of NPS 30 (ON 750) an d
larger, a tolerance of ±6 mm shall be allowed.
(4) For these valves, a tolerance of ±3 mm shall be allowed on the face-to-face dlmenslons for ali sizes and pressure classes.
(5) The data for offset seat valves, columns 7 through 9, are extracted from MSS SP·68 an d API 609 [except NPS 16 to NPS 24 (ON 400 to
DN 600) Class 600, which are only in MSS SP-68].
(6) The installed face·to-face dlmension ts the dimension of the valve face·to-face after installation in the pipeline. lt does not Include the
thickness of gaskets where separate gaskets are used. lt does Include the compressed (instatled) thickness of gaskets or seals that are
an integrai part of the valve.
20
ASME 816.10·2009
Table 9 Determlnation of Face-to-Face and End-to-End Dimenslons of Flanged Valves Having Varlous
Flange Facings
Face-to-Face [Notes {1) and (2}] Large or Small
2 mm 7 mm large or Small Rlng
Ralsed Ralsed Type
Materia! Class Flat Face Fa ce Fa ce Male Face l Tongue -Face )olnt Female Face Groove Face
Cast lron 125 (3)
250 (3)
Steel 125 (4) (3) +13 +13 (5) +10 +10

300 (4) (3) +13 +13 (5) +10 +10
600 to 2500 (3) (6) (6) (5) -3 -3
GENERAl NOTE: Dimensions are in millimeters.

NOTES:
(l) To determlne the face-to-face or end-to-end dimensions of valves having both flanges as tabulated in this table, adjust the face-to-face
(not the buttwe\d end-to-end) dlmenslons shown foi' the valve type (gate, globe, etc.), materia!, class, an d slze in Tables 1 through 6
by the amount shown.
(2) Far center-to-face or center-to-end dlmensions of angle type valves, use one-half the numerica! adjustment shown herein.
(3) These face·to-face dlmensions are listed In Tables 1 through 6. (See table of deslred ·Class Number.)
(4) For Class 150 and for Class 300 steel valves havlng flat faces, either the full thickness of the flange or the thickness wlth the 2m m
raised face removed may be supplied unless otherwise speclfled. For full thlckness of flange, the face·to-face dimensions llsted for
2 mm ralsed face apply. Users are reminded that removing the_2 mm ralsed faces will make the face·to-face dlmensions nonstandard.
(5) The X dlmenslons given in Table 10 ad d ed to the appropriate raised face flange face-to-face dimensions of Tables 1 through 6 estab·
lish the end-to·end dimenslons of steel valves havlng flanges wlth ring jolnt faclngs.
(6) These face-to·face dimensions are those llsted for 7 mm ra·1sed face In Tables 3 through 6.
21
Copyright© 2009 by the.American Societ)' ofMechanical Engineers. d&b
Table 10 Classes 150 to 2500 Steel Valves Having End Flanges With Ring joint Facings, End-to-End Dimensions
~
.@()
a.g
g~.
=· '§.
~
1.- ~~ End-to-end
Center-to-
o - end
3@
~~
ero
G 'O
l 1 l 2 l 3 l 4 l 5 l 6 l 7 l 8 l 9 l 10 l 11 l 12
·~ ~ Nominai Valve
g. g. >
o> s
~=3. NPS "'
s:
m
Cii"
3 Q
y, 15 --- ... 11 3 -2 (1) 3 o 4 o 4 o 4 "'p:
l'l~ N
N % 20 ... ... 13 4 o 4 o 4 o 4 o 4 ~
G (Il
1 25 13 4 13 4 o 4 o 4 o 4 o 4 o
~ ~-
~ G
1% 32 13 4 13 4 o 4 o 4 o 4 3 3
,:,
o
o
1% o o o
o~~..,
13 4 4 4 4 4 3 3
40 13
"'
!'.;;:: 2 50 13 4 16 6 3 5 3 3 3 3 3 3
~ g 2% 16 6 5 3 3 3 3 6 3
~- =- 65 13 4 3
g ~-
n ~
3
4
so
100
13
13
4
4
16
16
6
6
3
3
5
5
3
3
4
4
3
3
3
3
6
10
3
4
o- 3 13 4
~ m 5 125 13 4 16 6 3 5 3 4 3
o,.
m ~
::; s· 6 150 13 4 16 6 3 5 3 4 6 3 13 4
0 G
H> O 3 4 10 4 16 5
8 200 13 4 16 6 3 5
>il 10 250 13 4 16 6 3 5 3 4 10 4 22 6
"';;:: 12 300 4 16 6 3 5 3 4 16 5 22 8
m 14 350
13
13 3 16 6 3 5 10 4 19 6
~ 16 400 13 3 16 6 3 5
5
10
13
4
5
22
22
8
8
18 450 13 3 16 6 3
20 500 13 3 19 6 6 5 13 5 22 10
22 550 13 (2) (3) 22 (2) 6 10 (2) 6
24 600 13 3 22 6 10 6 19 6 28 11
~
@ (")
'C o
&~
= ~-
&. !§.
o ~
Table 10 Classes 150 to 2500 Steel Valves Having End Flanges With Ring )oint Facings, End-to-End Dimensions (Cont'd)
~@
3 "'
1 l 2 3 l 4 5 l 6 7 l 8 9 l 10 11 l 12
-!!o
cr'o Nominai Valve
o "' Size Class 150 C1ass 300 Class 600 Class 900 Class 1500 Class 2500
=~
g_g.
o o NPS l DN x l s x l s x l s x l s x l s x l s
o > ... ...
. -
='s 26 650 25 (l) 6 13 (1) 6

a:~
-· 28 700 ... ... 25 (l) 6 13 (1) 6 . .. . .. ... . .. . .. ... >
s~ ... . .. . .. . .. . .. ... ...
~~
@ 30
32
750
800 ...
...
...
25
28
(l)
(l)
6
(2)
13
16
(l)
(1)
6
(2) ... . .. ... . .. . .. . .. "'"'m
.,
~-
e. 9.1
o
~
34 850 ... ... 28 (1) (2) 16 (l) (2) ... . .. ... . .. . .. . .. ~
"';..o
~-q 36 900 ... ... 28 (l) (2) 16 (1) (2) . .. . .. . .. . .. . .. . ..
g-g, GENERAL NOTES,
;.
o
o
3;::
~ g (a) Dimensions are in millimeters. "'
'"g ·~·""~
~- (b) Flanges confonn to those of ASME 816.5 for the corresponding size and pressure dass, except in NPS 22 (DN 550), NPS 26 (DN 650), and larger sizes. See Note (1).
(c) To determine the end-to-end dimensions of valves having flanges with ring joint fadngs, the X dimensions must be added to the nominai raised face flange face-to-face dimensions
o ~
o - of Tables 1 through 6. For angle and angle lift check valves, one-half of the X dimensions as listed in this table must be added to the nominai dimensions for center-to-end dimen-
~ ~
~
g
"'
0.9.
sions. For approximate distance between ends of flanges having octagonal or ovai ring gaskets, when rings are compressed, use S dimensions as listed in this table.
~ ~
o o NOTES'
...,~ (1) This dimension has a minus value because the height of the applicab\e ring joint face is l mm \ess than the height of the raised face.
>~
(2) Flanges for NPS 22 (DN 550), NPS 26 (DN 650), and larger sizes conform to those of MSS SP-44 and ASME 816.47, Series A for the corresponding size and pressure dass.
~ (3) S dimension is not detennined.
"'
~
INTENTIONALLY LEFr BLANK
24
ASME 816.10·2009
MANDATORY APPENDIX l
FACE-TO-FACE AND END-TO-END DIMENSIONS:
U.S. CUSTOMARY UNITS
25
No reproduction rnay be made ofthis material without written consent of ASME. ~
ASME 816.10·2009
Table 1-1 Class 125 Cast lron Flanged and Class 150 Steel Flanged and Buttwelding End Valves,
Face-to-Face and End·to-End Dlmenslons
Pia in face Raised fa ce Buttwelding end
1 2 3 4 5 6 7 8 9 10
Class 150 Steel
·'
Class 125 Cast lron
Flanged End (0.06 In. Ralsed Face} and
Flanged End (Fiat Face) Weldlng End
Plug Globe, Gate Plug
Gate, Llft Solld
Soli d Check, Soli d Wedge,
Wedge Regular Round an d Angle Wedge Double
Nominai an d an d Port, Swing an d an d Disc,
Valve Double Short Venturi Full Check Llft Oouble an d Short
Slze Disc, Bore, Disc,
Pattern, Pattern, [Note (1)), Check, Condult, Condult, Pattern,
NPS l DN A A A A A D A A 8 A
';. 8 4.00 4.00
% 10 4.00 4.00
y, 15 4.25 4.25
'l\ 20 4.62 4.62
1 25 5.50 5.50 {2) 5.50 5.00 5.00 5.50
tlf4 32 6.50 (2) 6.00 5.50 5.50
tY2 40 6.50 6.50 {2) 6.50 6.50 6.50 6.50
2 50 7.00 7.00 7.50 (2) 7.50 8.00. 4.00 7.00 7.00 8.50 7.00
21/2 65 7.50 7.50 8.25 (2) 8.25 8.50 4.25 7.50 7.50 9.50 7.50
3 BO 8.00 8.00 9.00 (2) 9.00 9.50 4.75 8.00 8.00 11.12 8.00
4 100 9.00 9.00 9.00 {2) 12.00 11.50 5.75 9.00 9.00 12.00 9.00
5 125 10.00 10.00 14.00 {2) 15.00 13.00 6.50 10.00 15.00 10.00
6 150 10.50 10.50 15.50 18.00 14.00 7.00 10.50 10.50 15.88 10.50
8 200 11.50 11.50 18.00 22.00 19.50 9.75 11.50 11.50 16.50 11.50
10 250 13.00 13.00 21.00 26.00 24.50 12.25 13.00 13.00 18.00 13.00
12 300 14.00 14.00 24.00 30.00 27.50 13.75 14.00 14.00 19.75 14.00
14 350 15.00 (3) 27.00 31.00 15.50 15.00 15.00 22.50
16 400 16.00 (3) 30.00 36.00 (4) 18.00 16.00 16.00 24.00
18 450 17.00 (3) 34.00 17.00 17.00 26.00
20 500 18.00 (3) 36.00 18.00 18.00 28.00
22 550 20.00 30.00

24 600 20.00 (3) 42.00 (5) 20.00 20.00 32.00
26 650 22.00 22.00 34.00 {6)
28 700 24.00 24.00 36.00 {6)
30 750 51.00 (5) 24.00 26.00 36.00 (6)
32 800 28.00 38.00 (6)

34 850 30.00 40.00 (6) 40.00
36 900 63.00 (5) 28.00 32.00 40.00 (6)
26
ASME 616.10-2009
Table 1-1 Class 125 Cast lron Flanged and Class 150 Steel Flanged and Buttweldlng End Valves,
Buttwelding
end
11 12 13 14 15 16 17 18 19 20 21
Class 150 Steel
F!anged End (0.06 In. Ralsed Face) and Welding End Flanged End Weldlng End
Plug Globe, Bali

Llft
Check,
Short Round an d Y-Giobe
an d Port, Swing Angle an d
Nominai Regular Regular Check and Llft Y-Swlng Long Short Long Short
Venturi Full
Valve Slze Pattern, Pattern, Bore, [Note (1)], Check, Check, Pattem, Pattern, Pattern, Pattern,
Pattern,
NPS J DN A 8 A A A and 8 DandE A and 8 A A 8 8
y, 8 4.00 2.00
% 10 4.00 2.00
'/, 15 4.25 2.25 5.50 4.25 4.25 5.50
% 20 4.62 2.50 6.00 4.62 4.62 6.00
1 25 7.00 5.00 2.75 6.50 5.00 5.00 6.50
t% 32 5.50 3.00 7.25 5.50 5.50 7.00

t% .40 8.75 6.50 3.25 8,00 6.50 6.50 7.50 7.50
2 50 10.50 7.00 10.50 8.00 4.00 9.00 7.00 7.00 8.50 8.50
2)12 65 12.00 11.75 8.50 4.25 11.00 7.50 7.50 9.50 9.50
3 80 13.00 8.00 13.50 9.50 4.75 12.50 8.00 8.00 11.12 11.12
4 100 12.00 14.00 9.00 17.00 11.50 5.75 14.50 9.00 9.00 12.00 12.00
5 125 15.00 15.00 14.00 (7) 7.00
6 150 15.50 18.00 15.50 16.00 (7) 8.00 18.50 15.50 10.50 18.00 15.88
8 200 18.00 20.50 18.00 19.50 9.75 23.50 18.00 11.50 20.50 16.50
10 250 21.00 22.00 21.00 24.50 12.25 26.50 21.00 13.00 22.00 18.00
12 300 24.00 25.00 24.00 27.50 13.75 30.50 24.00 14.00 25.00 19.75
14 350 27.00 27.00 31.00 15.50 27.00 15.00 30.00 22.50
16 400 30.00 30.00 36.00 (8) ,18.00 30.00 16.00 33.00 24.00
18 450 34.00 34.00 38.50 (9) 34.00 36.00 26.00
20 500 36.00 36.00 38.50 (9) 36.00 39.00 28.00
22 550 42.00 (9) 43.00
24 600 42.00 42.00 51.00 (9) 42.00 45.00 32.00
26 650 51.00 (9) 49.00
28 700 57.00 (9) 53.00
30 750 60.00 (9) 55.00
32 800 60.00
34 850 64.00
36 900 77.00 (9) 68.00
27
Copyright © 2009 by thc American Society ofMechanical Engineers. ~
ASME 816.10·2009
GENERAL NOTES:
(a) Dlmenslons are In lnches.
(b) See Table 1-9 for adjustments to tabulated dlmensions that may be required for certa in flange faclngs.
NOTES:
(1) These dimensions are not lntended to cover the type of check valve having the seat angle at approximately 45 deg to the run of the
valve, or the "Underwriter Pattern," or other patterns where large clearances are requlred.
(2) Regular pattern only. The face-to-face dimension of NPS 4 may be 12.00 at the manufacturer's optlon.
(4) Globe and horlzontal llft check only.
(6) Doub\e disc and condult onty.
(n Globe and horizontalllft check only. The face-to-face and end-to·end dimenslon for Class 150 steel flanged and buttwelding end swlng
check valves In NPS 5 is 13.00 and in NPS 6 ls 14.00.
(8) Globe and horizontallift check only. The face-to-face and end-to-end dlmension far Ciass 150 steel flanged and buttweldlng end swlng
check valves-ln NPS 16 ls 34.00
28
Copyright © 2009 by the American Society of Mechanical Engineers. &
ASME 816.10·2009
Table 1·2 Class 250 Cast lron Flanged and Class 300 Steel Flanged an d Buttweldlng End Valves,
Face-to·face and End·to·End Dlmensions

and Class 300 Steel
1 2 3 4 5 6 7 B 9
Flanged End (0.06 In. Ralsed Face) Flanged and Weldlng End
Gate, Plug Globe, Bali
Soli d LI~
Wedge Check,
Nominai an d an d Angle
Valve Double Short Regular Venturi Swlng and Llft Long Short Long
Slze Disc, Pattern, Pattern, Check, Pattern, Pattern, Pattern,
Pattern, Check,
NPS l DN A A A A A o A A and 8 8
y, 15 5.50 5.50
% 20 6.00 6.00
1 25 6.25 6.50 6.50
t% 32 7.00 7.00
tlf2 40 7.50 7.50 7.50 7.50
2 so 8.50 7.25 8.50 10.50 5.25 8.50 8.50 8.50

2% 65 9.50 8.00 9.50 11.50 5.75 9.50 9.50 9.50
3 80 11.12 9.25 11.12 12.50 6.25 11.12 11.12 11.12
4 100 12.00 10.50 12.00 14.00 7.00 12.00 12.00 12.00
5 125 15.00 15.25 15.75 7.88
6 150 15.88 14.88 16.75 15.88 17.50 8.75 15.88 15.88 18.00
8 200 16.50 19.75 16.50 21.00 10.50 19.75 16.50 20.50
10 250 18.00 22.38 23.50 18.00 24.50 12.2s 22.38 18.00 22.00
12 300 19.75 25.50 28.00 19.75 28.00 14.00 25.50 19.75 25.00
14 350 22.50 30.00 30.00 22.50 30.00
16 400 24.00 33.00 33.00 24.00 33.00

18 450 26.00 36.00 36.00 26.00 36.00
20 500 28.00 39.00 39.00 28.00 39.00
22 550 44.00 43.00 43.00
24 600 31.00 45.00 45.00 32.00 45.00
26 650 49.00 49.00

28 700 53.00 53.00
30 750 55.00 55.00
32 800 60.00 60.00
34 850 64.00 64.00
36 900 68.00 68.00
29
No reproduction may be rnade ofthis matetial without written consent of ASME. ~
ASME 816.10·2009
Face-to-Face and End-to-End Dimenslons (Cont'd)
Buttwelding
end

and Class 300 Ste~l
10 11 12 13 14 15 16 17
Class 300 Steel
Ftanged End (0.06 In. Ralsed Face) and Weldlng End
Gate, Plug
Solid
Wedge,
Double Short
Disc, Short and an d Round Globe Angle
Nominai Valve an d Venturi Venturi Regular Port, Full and llft and Llft Swing
Slze Condult, Pattern, Pattern, Pattern, Bore, Check, Check, Check,
NPS j DN A and B A 8 A A and B A and B DandE A and B
y, 15 5.50 (1) 6.00 3.00
% 20 6.00 (1) 7.00 3.50
1 25 6.50 (1) 6.25 (2) 7.50 8.00 4.00 8.50
t% 32 7.00 (1) 8.50 4.25 9.00
t% 40 7.50 7.50 (2) 9.50 9.00 4.50 9.50
2 so 8.50 8.50 10.50 (2) 11.12 10.50 5.25 10.50

2% 65 9.50 9.50 12.00 (2) 13.00 11.50 5.75 11.50
3 80 11.12 11.12 13.00 (2) 15.25 12.50 6.25 12.50
4 100 12.00 12.00 14.00 (2) 18.00 14.00 7.00 14.00
5 125 15.00 15.75 7.88 15.75
6 150 15.88 15.88 18.00 15.88 22.00 17.50 8.75 17.50

8 200 16.50 16.50 20.50 19.75 27.00 22.00 ù.oo 21.00
10 250 18.00 18.00 22.00 22.38 32.50 24.50 12.25 24.50
12 300 19.75 19.75 25.00 28.00 38.00 28.00 14.00 28.00
14 350 30.00 30.00 (3) 30.00 (3) 30.00 33.00
16 400 33.00 33.00 (3) 33.00 (3) 33.00 34.00

18 450 36.00 36.00 (3) 36.00 (3) 36.00 38.50
20 500 39.00 39.00 (3) 39.00 (3) 39.00 40.00
22 550 43.00 43.00 (3) 43.00 (3) 43.00 44.00
24 600 45.00 45.00 (3) 45.00 (3) 45.00 53.00
26 650 49.00 49.00 (3) 49.00 (3) 49.00 53.00

28 700 53.00 53.00 (3) 53.00 (3) 53.00 59.00
30 750 55.00 55.00 (3) 55.00 (3) 55.00 62.75
32 800 60.00 60.00 (3) 60.00 (3) 60.00
34 850 64.00 64.00 (3) 64.00 (3) 64.00
36 900 68.00 68.00 (3) 68.00 (3) 68.00 82.00
30
No reproduction rnay be made ofthis material without written consent of ASME. ~
ASME 816.10·2009
Face-to-Face and End-to-End Dimensions (Cont'd)
GENERAL NOTES:
(a) Dimensions are In inches.
(b) See Table 1-9 for adjustments to tabulated dlmenslons that may be required for certa! n flange facings.
NOTES:
(2) Plug - short pattern only.
31
No reproduction may be made of this materia! without w ritten con sent of ASME. ~
ASME 816.10·2009
Table 1·3 Class 600 Steel Flanged and Buttwelding End Valves, Face-to-Face and End-to-End Dimensions
Buttwe/ding
Raised face Buttwelding end end
1 2 3 4 5 6 7 8 9 10
Class 600 Steel
Flanged End (0.25 In. Raised Face) and Weldlng End
Bali Gate Plug Globe,
Llft
Soli d Check,
Wedge, Globe, Llft an d Angle
Double Check, Swlng Angle and Llft
Disc, and Regutar Round Round and Swlng Check, and Llft Check,
Nominai
Condult, Short and Bore, Bore, Check, Short Check, Short
Valve
Long long Pattern Venturi Full Full Long Pattern Long Pattern
Slze Pattern, Pattern, [Note (1)], Pattern, Port, Port, Pattern, [Note (1)], Pattern, [Note (1)]
NPS J DN A and 8 A and 8 8 A and B A 8 A and B 8 {)andE E
'h 15 6.50 6.50 (2) 6.50 3.25
% 20 7.50 7.50 (2) 7.50 3.75
1 25 8.50 8.50 5.25 8.50 (3) 10.00 8.50 5.25 4.25
t% 32 9.00 9.00 5.75 9.00 (3) 9.00 5.75 4.50
t'h 40 9.50 9.50 6.00 9.50 12.50 9.50 6.00 4.75
2 50 11.50 11.50 7.00 11.50 13.00 11.50 7.00 5.75 4.25

2% 65 13.00 13.00 8.50 13.00 15.00 13.00 8.50 6.50 5.00
3 80 14.00 14.00 10.00 14.00 17.50 14.00 10.00 7.00 6.00
4 100 17.00 17.00 12.00 17.00 20.00 22.00 17.00 12.00 8.50 7.00
5 125 20.00 15.00 20.00 15.00 10.00 8.50
6 150 22.00 22.00 18.00 22.00 26.00 28.00 22.00 18.00 11.00 10.00
8 200 26.00 26.00 23.00 26.00 31.25 33.25 26.00 23.00 13.00
10 250 31.00 31.00 28.00 31.00 37.00 40.00 31.00 28.00 15.50
12 300 33.00 33.00 32.00 33.00 42.00 42.00 33.00 (4) 32.00 16.50
14 350 35.00 35.00 35.00 35.00 35.00 (4)
16 400 39.00 39.00 39.00 39.00 39.00 (4)

18 450 43.00 43.00 43.00 43.00 (5) 43.00 (4)
20 500 47.00 47.00 47.00 47.00 (5) 47.00 (4)
22 550 51.00 51.00 51.00 (5) 51.00 (4)
24 600 55.00 55.00 55.00 55.00 (5) 55.00 (4)
26 650 57.00 57.00 57.00 (5) 57.00 (4)

28 700 61.00 61.00 63.00 (4)
30 750 65.00 65.00 65.00 (5) 65.00 (4)
32 800 70.00 70.00 (6) 70.00 (5)
34 850 76.00 76.00 (6) 76.00 (5)
36 900 82.00 82.00 (6) 82.00 (5) 82.00 (4)
32
ASME 816.10·2009
Table 1·3 Class 600 Steel Flanged and Buttwelding End Valves, Face-to·Face and
End-lo-End Dimensions (Cont'd)
GENERAL NOTES:
(a) Dimensions are in inches.
(b) See Table 1·9 for adjustments to tabulated dimensions that may be required for certa! n flange faclngs.
NOTES:
(1) These dimensions apply to pressure seal or flangetess bonnet valves. They may be applied at the manufacturer"s optlon to valves with
flanged bonnets.
(4) Swing check on\y.
(6) Doub\e disc and conduit on\y.
33
Copyright © 2009 by the American Soeiety of Mechanical Engineers. ~
No rcproduction may be made ofthis materia{ without written conscnt of ASME. ~
ASME 816.10·2009
Table 1·4 Class 900 Steel Flanged and Buttwelding End Valves, Face·to-Face and End·to·End Dlmensions
Buttwelding
Raised tace Buttwelding end end
1 2 3 4 5 6 7 8 9
Class 900 Steel Valves
Flanged End {0.25 In. Ralsed Face) and Weldlng End
Gate Plug
Globe, Bali
Soli d Llft Globe, Llft
Wedge, Check, Check, Angle
Double an d and Swlng Angle and and Llft
Disc, and Regular Round Swing Check, Llft Check,
Condult, Short an d Port, Check, Short Check, Short
Nominai Valve long Pattern Venturi Full long Pattern Long Pattern Long
Slze Pattern, [Note (1)], Pattern, Bore, Pattern, [Note (1)1, Pattern, [Note (1)1 Pattern,
NPS l DN A and B 8 A and 8 A A and B 8 DandE E A and 8
% (2) 20 (2) 9.00 4.50
1 (2) 25 (2) 10.00 (3) 5.50 10.00 (4) 10.00 5.00 10.00
l'1. (2) 32 (2) 11.00 (3) 6.50 11.00 (4) 11.00 5.50 11.00
1y, (2) 40 (2) 12.00 (3) 7.00 12.00 (4) 14.00 12.00 6.00 . 12.00
2 (2) 50 (2) 14.50 8.50 14.50 (4) . 15.00 14.50 .. ~. 7.25 14.50
2Y, (2) 65 (2) 16.50 10.00 16.50 (4) 17.00 16.50 10.00 8.25 16.50
3 BO 15.00 12.00 15.00 (4) 18.50 15.90 12.00 7.50 6.00 15.00
4 100 18.00 14.00 18.00 (5) 22.00 18.00 14.00 9.00 7.00 18.00
5 125 22.00 17.00 22.00 17.00 11.00. 8.50
6 150 24.00 20.00 24.00 29.00 24.00 20.00 12.00 10.00 24.00
8 200 29.00 26.00 29.00 32.00 29.00 26.00 14.50 13.00 29.00
10 250 33.00 31.00 33.00 38.00 33.00 31.00 16.50 15.50 33.00
12 300 38.00 36.00 38.00 44.00 38.00 36.00 19.00 18.00 >~.00
14 350 40.50 39.00 40.50 39.00 20.25 19.50 40.50
16 400 44.50 43.00 44.50 (5) 44.50 (6) 43.00 26.00 44.50
18 450 48.00 48.00 (6) 29.00 48.00

20 500 52.00 52.00 (5) 52.00 (6) 32.50 5.2,00
22 550
24 600 61.00 61.00 (6) 39.00 61.00
GENERAL NOTES,
(a) Dimensions are in lnches.
(b) see Table 1·9 for adjustments to tabulated dimenslons that may be requlred for certa in flange facings.
NOTES,
(l) These dimensfons apply to pressure seal or flangeless bonnet valves. They may be applled at the manufacturer's option to valves with
flanged bonnets.
(2) The connecting end flanges for C\ass 900 valves, NPS 2'll and smaller, are identica\ to those of Class 1500 vatves. The face·to·face
dlmensions for alt Class 900 valves, NPS 2'h and smaller, except round port full bOre plug valves (column 4), are identica! with those
of Class 1500 valves.
(6) swlng check only.
34
Copyright © 2009 by the American Society of Mechanical Engineers. r.®;;,
No reproduction may be made ofthis materia\ without written consent of ASME. ~
ASME 816.10·2009
Table 1·5 Class 1500 Steel Flanged and Buttwelding End Valves, Face·to-Face and
End·to·End Dimensiì'lo.,.ns;;......_ _ __
Buttwelding
end
1 2 3 4 5 6 7 8
Class 1500 Steel
Ftanged End (0.25 In. Raised Face) 8nd Weldlng End
Gate Plug Bali
Soli d Globe, Llft
Wedge, Globe, Llft Check,
Doubte Check, and Swlng Angle and
Disc, and Regular Round and Swlng Check, Llft
Nominai .
Condult, Short an d Port, Check, Short Check,
Valve long Pattern Venturi Full Long Pattern LOng Long
Slze Pattern, [Note (1)]. Pattern, Bore, Pattern, [Note (1)], Pattern, Pattern,
NPS j ON A and 8 8 A and B A A and 8 8 DandE A and B
'h 15 8.50 (2) 4.25

% 20 9.00 4.50
1 25 10.00 (3) 5.50 10.00 (4) 10.00 5.00
t% 32 11.00 (3) 6.50 11.00 {4) 11.00 5.50
t'h 40 12.00 (3) 7.00 12.00 (4) 12.00 6.00
2 50 14.50 8.50 14.50 (4) 15.38 14.50 8.50 7.25 14.50
l'h 65 16.50 10.00 16.50 (4) 17.88 16.50 10.00 8.25 16.50
3 80 18.50 12.00 18.50 (4) 20.62 18.50 12.00 9.25 18.50
4 100 21.50 16.00 21.50 (4) 24.62 21.50 16.00 10.75 21.50
5 125 26.50 19.00 26.50 19.00 13.25
6 150 27.75 22.00 27.75 31.00 27.75 22.00 13.88 27.75
8 200 32.75 28.00 32.75 35.00 32.75 28.00 16.38 32.75
10 250 39.00 34.00 39.00 42.00 39.00 34.00 19.50 39.00
12 300 44.50 39.00 44.50 48.00 44.50 39.00 22.25 44.50
14 350 49.50 42.00 49.50 42.00 24.75 49.50
16 400 54.50 47.00 54.50 (5) 54.50 (6) 47.00 54.50
18 450 60.50 53.00 60.50 {6)
20 500 65.50 58.00 65.50 {6)
22 550
24 600 76.50 76.50 {6)
GENERAL NOTES,
(a) Dlmensions are in inches.
(b) See Table 1·9 for adjustments to tabulated dlmensions that may be requlred for certain flange facings.
NOTES'
(1) These dlmensions app(y to pressure seal or fiangeless bonn et valves. They may be applied at the manufacturer's option to valves with
fianged bonnets.
(2) G(obe an d lift check only.
(3) Sotid wedge onty.
(6) Swlng check only.
35
Copyright © 2009 by the American Society of Mechanical Engineers. r.Qib
No reproduction may be made ofthis material without written conscnt of ASME. ~
ASME 816.10·2009
Table 1-6 Class 2500 Steel Flanged and Buttweldlng End Valves, Face-to-Face and
End-to-End Dimenslons
Buttwelding
Buttwelding end end
Raised face
1 2 3 4 5 6 7
Class 2500 Steel
Flanged End (0.25 In. Ralsed Face) and Weldlng End
Gate Globe, Llft Bali
Solld Wedge, Globe, Llft Check, and Angle and
Nominai and Double Short Plug, Check, and Swlng Check, Llft Check,
Valve Swlng Check, Short Pattern
Disc, Long Pattern Regular Long Long
Slze
Pattern, [Note (1)], Pattern, Long Pattern, [Note (1)], Pattern, Pattern,
NPS l DN A and B 8 A and B A and 8 8 DandE A and 8
'h 15 10.38 (2) 10.38 5.19
'1. 20 10.75 (2) 10.75 5.38
1 25 12.12 (2) 7.31 12.12 12.12 6.06
t% 32 13.75 (2) 9.12 13.75 6.88
tY2 40 15.12 (2) 9.12 15.12 15.12 7.56
2 50 17.75 11.00 17.75 17.75 11.00 8.88 17.75
2% 65 20.00 13.00 20.00 20.00 13.00 10.00 20.00

3 80 22.75 14.50 22.75 22.75 14.50 11.38 22.75
4 100 26.50 18.00 26.50 26.50 18.00 13.25 26.50
5 125 31.25 21.00 31.25 31.25 21.00 15.62
6 150 36.00 24.00 36.00 36.00 24.00 18.00 36.00
8 200 40.25 30.00 40.25 40.25 30.00 20.12 40.25
10 250 50.00 36.00 50.00 50.00 36.00 25.00 50.00

12 300 56.00 41.00 56.00 56.00 41.00 28.00 56.00
14 350 44.00
16 400 49.00
18 450 55.00
GENERAL NOTES:
(a) Dimensfons are In inches.
(b) See Table 1·9 for adjustments to tabulated dlmensions that may be required far certa in flanged faclngs.
NOTES:
(l} These dimensions apply to pressure seal or flangeless bonn et valves. They may be app\led at the manufacturer"s option to valves wlth
flanged bonnets.
36
No reproduction may be m ade of this material without written consent of ASME. ~
ASME 816.10·2009
Table 1·7 Classes 125 and 250 Cast lron and Classes 150 to 2500 Steel Wafer Type Valves,
Face·to·Face Dimensions
1 2
l 3 4
l 5
l 6
l 7
l 8
l 9 10 l 11 l 12 l 13 l 14
Cast lron
Steel !Note (2)1
[Note (1)]
Swlng Check, Swlng Check, Slngle an d Duat Plate, lnstallatlon Betwéen Standard
Slngle and ANSI Flanges [Note (3)]
Dual Plate,
Bonnet· lnstallatlon
less Between
Knlfe Gate, Standard ANSI
Nominai Class 150 Flanges Class Class
Valve Flange
Slze Matlng Class 150 J 300 l 600 l 900 l 1500 l 2500 150 l 300 l 6001 900 /1500
NPS l DN Dlmenslons 125 l 250 Long Pattern [Note (4)1 Short Pattern [Note (5)1
2 50 1.88 2.12 2.12 2.38 2.38 2.38 2.75 2.75 2.75 0.75 0.75 0.75 0.75 0.75
2% 65 2.38 2.38 2.62 2.62 2.62 3.25 3.25 3.25 0.75 0.75 0.75 0.75 0.75
3 80 2.00 2.62 2.62 2.88 2.88 2.88 3.25 3.25 3.38 0.75 0.75 0.75 0.75 0.88
4 100 2.00 2.62 2.62 2.88 2.88 3.12 4.00 4.00 4.12 0.75 0.75 0.88 0.88 1.25
5 125 2.25 3.25 3.25
6 150 2.25 3.75 3.75 3.88 3.88 5.38 6.25 6.25 6.25 0.75 0.88 1.12 1.38 1.75
8 200 2.75 5.00 5.00 5.00 5.00 6.50 8.12 8.12 8.12 1.12 1.12 1.50 1.75 2.25
10 250 2.75 5.50 5.50 5.75 5.75 8.38 9.50 9.75 10.00 1.12 1.50 2.25 2.25 2.88
12 300 3.00 7.12 7.12 7.12 7.12 9.00 11.50 12.00 12.00 1.50 2.00 2.38
14 350 3.00 7.25 8.75 7.25 8.75 10.75 14.00 14.00 1.75 2.00 2.62
16 400 3.50 7.50 9.12 7.50 9.12 12.00 15.12 15.12 2.00 2.00 2.88
18 450 3.50 8.00 10.38 8.00 10.38 14.25 17.75 18.44 2.38 3.00 3.25
20 500 4.50 8.38 11.50 8.62 11.50 14.50 17.75 21.00 2.50 3.25 3.62
24 600 4.50 8.75 12.50 8.75 12.50 17.25 19.50 22.00
30 750 12.00 14.50 12.00 14.50 19.88
36 900 14.50 19.00 14.50 19.00 25.00
42 1050 17.00 22.38 17.00 22.38 27.62
48 1200 20.62 24.75 20.62 24.75
GENERAL NOTES:
(a) Dlmenslons are in lnches.
(b) The tolerances of para. 5.1 apply to face-to·face dimensions for sizes NPS 24 and smaller. For sizes NPS 30 and larger, the tolerance
shall be ±0.25 in.
NOTES:
(1) These data are extracted from MSS SP·Bl that covers non·Ciass designated (l.e., cold working pressure) rated for 150°F (66°C} maxi-
mum knlfe gate valves that have ASME 816.5, Class 150 flange bolting templates.
(2) These. data for cast lron swlng check valves are extracted from API 594.
(3) Valves of sizes NPS 30 and targer In Classes 150, 300, and 600 shall have body outslde dlameters and gasket surface dimenslons
compatible with flange standards speclfied in the purchase order, e.g., ASME B16.47 Sr. B or ASME 816.47 Sr. A (MSS SP-44).
(4) These data for long pattern steel swing check valves in slzes NPS 24 an d smaller are extracted from API 60 and API 594. Data for
larger sizes are extracted from API 594.
(5) These data for short pattern steel swing check valves are extracted from API 60.
37
No repfoduction may be made ofthis material without written consent of ASME. ~
ASME 816.10·2009
Table 1-8 Classes 25 and 125 Cast lron and Classes 150 to 600 Steel Butterfly Valves,
Face-to-Face Dlmensions
l
l 2 3
l 4
l 5 6 7 8 9
Steel Offset Seat Lug and
Cast lron and Class 150 Steel Steel Grooved End Wafer Style
[Notes (1), (2), and (3)] [Notes (l) and (3)] [Notes (4) and (5)]
Nominai Valve Flanged End lug and Wafer Style [Note (6)]
NPS
Slze
J DN Narrow l W/de Narrow l Wide l Extra W/de
Ctass
150
Class
150
Class
300
Class
600
t% 40 1.31 1.44 1.50 3.38
2 50 1.69 1.75 1.81 3.19
2% 65 1.81 1.94 2.00 3.81
3 80 s.oo 5.00 1.81 1.94 2.00 3.81 1.88 1.88 2.12
4 100 5.00 7.00 2.06 2.19 2.25 4.56 2.12 2.12 2.50
5 125 5.00 7.50 2.19 2.50 2.56 5.81
6 150 s.oo 8.00 2.19 2.75 2.81 5.81 2.25 2.31 3.06
8 200 6.00 8.50 2.38 2.81 2.94 5.25 2.50 2.88 4.00
10 250 8,00 15.00 2.69 3.00 3.12 6.25 2.81 3.25 4.62
12 300 8.00 15.00 3.06 3.25 3.38 6.50 3.19 3.62 5.50
14 350 8.00 16.00 3.06 3.62 3.75 7.00 3.62 4.62 6.12
16 400 8.00 16.00 3.12 4.00 4.12 7.00 4.00 5.25 7.00
18 450 8.00 16.00 4.00 4.50 4.62 8.00 4.50 5.88 7.88
20 500 8.00 18.00 4.38 5.00 5.12 8.50 5.00 6.25 8.50
24 600 8.00 18.00 6.06 6.19 10.00 6.06 7.12 9.13
30 750 12.00 22.00 6.50
36 900 12.00 22.00 7.88
42 1050 12.00 24.00 9.88
48 1200 15.00 26.00 10.88

54 1350 15.00 28.00
60 1500 15.00 30.00
66 1650 18.00 34.00
72 1800 18.00 36.00
GENERAl NOTE: Dlmenslons are in lnches.

NOTES:
(1) These butterfly valves are of the design generally havlng concentric location of disc an d seat, covered by MSS SP-67, from which these
data are extracted.
(2) These valves are dimensionally compatlble wlth flanges conforming to ASME 816.1 Class 25 or Class 125, ASME 816.5 Class 150,
ASME 816.24 Class 150, ASME 816.42 Class 150, or AWWA C-207.
(3) For these butterfly val ves, a tolerance of ±0.06 in. shall be allowed on face-to-face dimensions of valves of NPS 6 and smaller, an d a
tolerance of ±0.13 in. on NPS 8 and larger, except that For single flange and flangeless valves of NPS 30 an d larger, a toierance of
:t0.25 in. shall be allowed.
(4) For these valves, a tolerance of ±0.13 In. shall be allowed on the face-to-face dimensions forali sizes and pressure classes.
(5) The data for offset seat valves, columns 7 through 9, are extracted from MSS SP-68 and API 609 (except 16" to 24" Class 600, which
are only in MSS SP·68).
(6) The installed face·to-face dimension is the dimenslon of the valve face-to·face after installatlon in the plpeline. lt does not include the
thickness of gaskets where separate gaskets are used. lt does include the compressed (installed) thickness of gaskets or seals that are
an integrai part of the valve.
38
Copyright © 2009 by the American Society of Mechanical Engineers. dih
ASME 816.10·2009
Table 1-9 Determination of Face-to-Face and End-to-End Dimenslons of

Flanged Valves Having Various Flange Faclngs
face-to-Face {Notes (1) and (2)] End·to·End [Notes (1) and (2)]
0.061n. 0.25 In.

Large or Small Rlng Large or Small
Flat Ralsed Ralsed Male Tongue Type Female Groove
Materia( Class Fa ce Face Fa ce Fa ce l Fa ce Jolnt Fa ce l Face
Cast iran 125 (3)

250 (3)
Steel 150 (4) (3) +0.50 +0.50 (5) +0.38 +0.38

300 (4) (3) +0.50 +0.50 (5) +0.38 +0.38
600 to 2500 (3) (6) (6) (5) -0.12 -0.12
GENERAL NOTE: Dimenslons are in lnches.

NOTES:
(1) To determine the face-to-face or end-to-end dlmensions of valves having both flanges as tabulated In thls table, adjust the face-to-face
(not the buttwe\d end-to-end) dimensions shown for the valve type (gate, glebe, etc.), materia\, class, and slze in Tables l-1 through 1·6
by the amount shown.
(2) For center-to-face or center-to-end dimenslons of angle type valves, use one·half the numerica\ adjustment shown h ere in.
(3) These face·to·face dimensions are listed in Tables 1·1 through 1·7. (See table of desired class.)
(4) For Class 150 and for C\ass 300 steel valves havlng flat faces, either the full thickness of the flange or the thlckness with the 0.06 in.
ralsed face removed may be supplied unless otherwise specified. For full thckness of flange, the face·to·face dimensions llsted for 0.06
In. raised face apply. Users are reminded that removlng the 0.06 in. raised faces will make the face-to-face dlmensions nonstandard.
(5) The X dlmenslons given In Table 1·10 added to the appropriate raised face flange face-to-face dlmensions of Tables 1·1 through 1·6
establish the end-to-end ~imenslons of steel valves having flanges with ring joint faclngs.
(6) Thesè face-to-face dimensions are those listed for 0.25 In. raised face in Tables 1·3 through 1·6.
39
Table 1-1 O Classes 150 to 2500 Steel Valves Having End Flanges With Ring )oint Facings, End-to-End Dimensions
z l
o l.. l Ring joint
an
"' o
a"'
C.'<
§~-l j.__ End-to-end _..j Center-to-
"·o =-~ end
~@
~~
.,.o
o 'O
l l l 2 l 3 l 4 l 5 l 6 l 7 l 8 l 9 l lO l 11 l 12
3~'<"" Nominai Valve
g-g- ~
o>
~3
NPS x U>
-·
~ o
3 g
!!:
~.
~ ... y,
%
15
20
...
...
...
. ..
0.44
0.50
0.12
0.16
-0.06 (1)
o
0.12
0.16
o
o
0.16
0.16
o
o
0.16
0.16
o
o
0.16
0.16
.
;:
m
~
!"
o ~
o "' l 25 0.50 0.16 0.50 0.16 o 0.16 o 0.16 o 0.16 o 0.16 c

[ ~-
~ o
t% 32 0.50 0.16 0.50 0.16 o 0.16 o 0.16 o 0.16 0.12 0.12
,:,
c
c
t'h o o o
5=~ 40 0.50 0.16 0.50 0.16 0.16 0.16 0.16 0.12 0.12
"'
o "
"';;::
~ g
2 50 0.50 0.16 0.62 0.22 0.12 0.19 0.12 0.12 0.12 0.12 0.12 0.12
~. =- 2% 65 0.50 0.16 0.62 0.22 0.12 0.19 0.12 0.12 0.12 0.12 0.25 0.12
~§ 3 80 0.50 0.16 0.62 0.22 0.12 0.19 0.12 0.16 0.12 0.12 0.25 0.12
= o· 4 100 0.50 0.16 0.62 0.22 0.12 0.19 0.12 0.16 0.12 0.12 0.38 0.16
g e.
~ "' 5 125 0.50 0.16 0.62 0.22 0.12 0.19 0.12 0.16 0.12 0.12 0.50 0.16
-·
~ ~
Goq
~
~ ~
0.25
oH> oO 6 150 0.50 0.16 0.62 0.22 0.12 0.19 0.12 0.16 0.12 0.50 0.16
8 200 0.50 0.16 0.62 0.22 0.12 0.19 0.12 0.16 0.38 0.16 0.62 0.19
>il 0.12 0.19 0.12 0.16 0.38 0.16 0.88 0.25
0.50 0.16 0.62 0.22
"';;:: 10
12
250
300 0.50 0.16 0.62 0.22 0.12 0.19 0.12 0.16 0.62 0.19 0.88 0.31
!" 0.12 0.62 0.22 0.12 0.19 0.38 0.16 0.75 0.22
14 350 0.50
~ 16 400 0.50 0.12 0.62 0.22 0.12 0.19 0.38 0.16 0.88 0.31
18 450 0.50 0.12 0.62 0.22 0.12 0.19 0.50 0.19 0.88 0.31
20 500 0.50 0.12 0.75 0.22 0.25 0.19 0.50 0.19 0.88 0.38
22 550 0.50 (2) (3) 0.88 (2) 0.25 0.38 (2) 0.22
24 600 0.50 0.12 0.88 0.25 0.38 0.22 0.75 0.22 1.12 0.44
~
.8n
a.g
"'o~~-
· ,.~
Table 1-10 Classes 150 to 2500 Steel Valves Having End Flanges With Ring joint Facings, End-to-End Dimensions (Conrd)
~@
s "' 1 l 2 3 l 4 5 l 6 7 l 8 9 l 10 11 l 12
~8 Nominai Valve
g";o
Size Class 150 Class 300 Class 600 Class 900 Class 1500 Class 2500
=~
g.
G
g.
G
NPS l DN x l s x l s x l s x l s x l s x _l_ s_
o )>
='s 26 650 ... ... 1.00 (2) 0.25 0.50 (2) 0.22
[. g_ 28 700 ... ... 1.00 (2) 0.25 0.50 (2) 0.22 . .. ... ... ... ... ... >
s2
~
!l" m
~-0
n. l~
!:?..
~
30
32
34
750
800
850
...
...
...
...
...
...
1.00
1.12
1.12
(2)
(2)
(2)
0.25
(3)
(3)
0.50
0.62
0.62
(2)
(2)
(2)
0.22
(3)
(3)
...
. ..
...
. ..
...
. ..
...
. ..
. ..
. ..
. ..
...
. ..
...
...
. ..
. ..
. ..
.."'
"'
;:
m
~
~-~ 36 900 ... ... 1.12 (2) (3) 0.62 (2) (3) . .. . .. . .. ... ... . .. ;..
'?
g-~
N
c
GENERAL NOTES, c
s;;:: "'
~ g (a) Oimensions are in inches.
~- ~ (b) Flanges conform to those of ASME 816.5 for the corresponding size and pressure class, except in NPS 22, NPS 26, and larger sizes. See Note (1).
~ o (c) To detenni ne the end-to-end dimensions of valves having flanges with ring joint facings, the X dimensions must be added to the nominai raised face flange .face-to-face dimensions
o E!.
of Tables 1-1 through 1-6. For angle and angle lift check valves, one-half of the X dimensions as listed in this table must be added to the nominai dimensions for center-to-end dimen-
o~ ~
"' sions. For approximate distance between ends of flanges having octagonal or ovai ring gaskets, when rings are compressed, use S dimensions as listed in this table.
GO<>
~
~
0 G
...,G
-·
~
NOTES'
(1) This dimension has a mi nus value because the height of he applicable ring joint face is 0.22 in., whereas the height of the raised face is 0.25 in.
>~
(2) Flanges for NPS 22, NPS 26, and larger sizes confonn to those of MSS SP-44 and ASME 816.47, Series A for the corresponding size an d pressure class.
~ (3) S dimension is not determined.
~
ASME 816.10·2009
NONMANDATORY APPENDIX A
REFERENCES
The following is a list of puhlications referenced in NY 10016; Order Departrnent: 22 Law Drive, Box 2300,
this Standard. Fairfield, NJ 07007 (www.asme.org)
API 6D, Twenty-Third Edition, Specification for Pipeline AWWA C207-94, Steel Pipe Flanges for Waterworks
Valves Service, Sizes 4 In. Through 144 In. (100 mm Through
API 594, Sixth Edition, Wafer and Wafer-Lug Check 3600 mm)
Valves
API 609, Sixth Edition, Lug-and-Wafer-Type Butterfly Publisher: American Water Works Association (AWWA),
Valves 6666 W. Quincy Avenue, Denver, CO 80235 (www.aw-
Publisher: American Petroleum Institute (API), 1220 wa.org)
L Street, NW, Washington, DC 20005 (www.api.org) MSS SP-44-2006, Steel Pipe Line Flanges
ASME B16.1, Cast Iron Pipe Flanges and Flanged MSS SP-67-2002a, Butterfly Valves
Fittings, Class 25, 125, 250, and 800 MSS SP-68-1997 (R2004), High Pressure Butterfly Valves
ASME B16.5, Pipe Flanges and Flanged Fittings with Offset Design
ASME 816.24, Cast Copper Alloy Pipe Flanges and MSS SP-81-2006, Stainless Steel Bonnetless, Flanged
Flanged Fittings, Class 150, 300, 400, 600, 900, 1500, Knife Gale Valves
and 2500 Publisher: Manufacturers Standardization Society of the
ASME 816.34, Valves - Flanged, Threaded, and Valve and Fittings Industry (MSS), 127 Park Street,
Welding End NE, Vienna, VA 22180 (www.mss-hq.org)
ASME 816.42, Ductile Iron Pipe Flanges and Flanged
Fittings, Class 150 and 300 Publications appearing above that have been
ASME 816.47, Large Diameter Steel Flanges NPS 26 approved as American National Standards may also be
through NPS 60 obtained from the American National Standards
Publisher: The American Society of Mechanical Institute (ANSI), 25 West 43rd Street, New York, NY
Engineers (ASME), Three Park Avenue, New York, 10036.
42
Copyright © 2009 by the American- Society of Mechanical Engineers. ~
1
© 2009 by the American Society of Mechanical Engineers.
~'ro:~~~ be made of this material without written consent of ASME.
ISBN-13: 978-0-7918-3216-5
ISBN-10: 0-7918-3216-3
J03109
+Normes •
ASME
~~!!
• UK/International
llpt~IJII www.ili.co.uk
standards@saiglobal.com
lndex House, Ascot, Berks
SL5 ?EU UK
'2:' +44 (0)1344 636300
Fax: +44 (0)1344 291194
., USA
www.ili-info.com
m
uspubsales@saiglobal.com
61 O Winters Avenue
Paramus, NJ 07652
NFPA® '2:' 201-986-1131
Fax: 201-986-7886
• IRISH OFFICE
www.standards.ie
info@standards.ie
42/44 Northumberland Road
Dublin 4
'2:' o1 857 67 30
•IEEE
Fax: 01 857 67 29
• SIERVICE FRANCAIS
www.ilifrance.com
normes@saiglobal.com
~.
25 Rue de Ponthieu,
75008, Paris
\:!/ '2:' 01 53 7517 65
Fax: 01 53 75 16 95
• DEIIJTSCHE ABTEILUNG
SAE www.ilideutschland.com
normen@saiglobal.com
Dietlindenstrasse 15
D-80802, Munchen
'2:' (089) 848 158
Fax: (089) 84 00 64 40
• UFFICIO iTALIANO
www.iliitalia,com
norme@saiglobal.com
Via Guido D'arezzo 4
20145, Milano
'2:' 02 283 40114
Fax: 02 283 40310
and more
··SAIGLOBAL IN DEX HOUSE ASCOT BERKS SL5 7EU UK W +44 (0)1344 636 30()
Servfce françaJs: 01 53 75 17 65 Deutsche Abtellung: (089) 84 81 58

Asme B16.10 - 2009 PDF

Uploaded by

Copyright:

Available Formats

Asme B16.10 - 2009 PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Asme B16.10 - 2009 PDF

Uploaded by

Copyright:

Available Formats

What is the purpose of this document?

What is the purpose of this document?

What standards are referenced in this document?

What standards are referenced in this document?

Face-to-Face

AN AMERICAN NATIONAL STANDARD

Copyright© 2009 by the American Society ofMechanical Enginecrs. ~

ASME is the reglstered trademark of The American Society Of Mechanical Englneers.

No part of this document may be reproduced in any form,

The Amerlcan Society of Mechanical Englneers

Copyright © 2009 by the American Socicty ofMechanical Engineers. ~

STANDARDS COMMITTEE OFFICERS

STANDARDS COMMITTEE PERSONNEL

SUBCOMMITTEE N - STEEL VALVES

FACE-TO-FACE AND END-TO-END

1 SCOPE 1.3 Cast lron Valves

for various types and sizes of valves are specified in NPS DN

Fig. 1 Flange Facings and Thelr Relatlonships

Face-to-fa ce dimension given in the tables Face-ta-fa ce dimension

Face-to-fa ce dimension given in the tab/es Face-ta-face dimensian

End-to-end dimension [see Table 10 (Table 1-10)] End-to-end dimensian

Facing far steel

(a) Regular Standard Facings (b) Other Standard Facings

Fig. 2 Welding Ends

(al Plaln Bevel (b) Compound Bevel

Pia in face Raised face Buttwelding end

Gate, Plug Gate Plug

'1. 8 102 102

t% 32 165 (2) 152 140 140

22 550 508 762

32 800 711 965 (6)

tY4 32 140 76 184 140 140 178

22 550 1 067 (9) 1 092

Raised face Buttwelding end

Class 250 Cast lron Class 300 Steel

2 50 216 184 216 267 133 216 216 216

16 400 610 838 838 610 838

26 650 1 245 1 245

Class 250 Cast lron Class 300 Steel

\1, 15 140 (1) 152 76

2 50 216 216 267 (2) 282 267 133 267

6 150 403 403 457 403 559 444 222 444

16 400 838 838 (3) 838 (3) 838 864

26 650 1 245 1 245 (3) 1 245 (3) l 245 1 346

2 50 292 292 178 292 330 292 178 146 108

16 400 991 991 991 991 991 (4)

26 650 1448 1448 l 448 (5) l 448 (4)

18 450 l 219 l 219 (6) 737 1 219

2 50 368 216 368 (4) 391 368 216 184 368

6 150 705 559 705 787 705 559 353 705

16 400 1 384 1194 l 384 (5) l 384 (6) 1194 1 384

2% 65 508 330 508 508 330 254 508

lO 250 l 270 914 l 270 l 270 914 635 1 270

6 150 127 203 56 70 71 148 57 59 78

48 1 200 381 660 276

GENERAL NOTE: Dlmenslons are In mlllimeters.

Steel 125 (4) (3) +13 +13 (5) +10 +10

GENERAl NOTE: Dimensions are in millimeters.

='s 26 650 25 (l) 6 13 (1) 6