Termooo Standard

Introduction
Maverick Applied Science provides piping engineering and pipe supports to

heavy and light industries for nearly every application.
The Maverick Approach begins with our extraordinary group of

designers and engineers. With their 100-plus years of expertise in
pipe support design and engineering and FRP piping, they form the
backbone of Maverick.
But our engineers are not only expert designers of pipe supports
and systems; they epitomize our “engineering is a people business”
approach. Our company philosophy is focused on you, our
customer, and your project. After all, your success is our success
and we work very hard to guarantee both.
The Maverick Difference comes from our dual focus on pipe

support design coupled with high quality manufacturing. Maverick
pipe support designs are:
• Based on practical, efficient concepts that provide the greatest
ease of installation and reliable service.
• Modeled in 3D using Solid Edge™ to assure proper fit,
fabrication and installation accuracy as well as ease of
adjustment to suit your project.
• Competitively priced.
Maverick pipe support designs provide:

• Long term performance and durability.
• The most flexibility and choices for your project.
Maverick Applied Science, Inc. 5th Edition Page 1

Introduction
Maverick pipe and duct supports meet or exceed your defined project
requirements and are:
• Tailored to best suit your application.
• Designed and built in compliance with standard practice MSS
SP-58, Pipe Hangers and Supports – Materials, Design and
Manufacture.
• Available in carbon steel, stainless steel, aluminum, alloys and
fiberglass construction.
• Available in plain, painted or hot dipped galvanized finishes.
• “Made in America”.
In addition to pipe supports, Maverick Applied Science provides engineering and

inspections for domestic and foreign companies involved in chemical processing,
desalination, power utilities, mineral processing and water/wastewater processing.
Maverick engineers and inspectors are internationally recognized for expertise in composite
materials for corrosive applications. With over 150 years of combined FRP engineering
experience, the Maverick team provides
Engineering and Consulting

• Material Specifications
• Equipment Design
• Pipe Stress Analysis
• Finite Element Analysis
• Failure Investigation and Analysis
Inspections
• Vendor Qualifications
• Shop Surveillance
• Field QA Inspection
• Equipment Inspection
• Maintenance Assessment
• Materials Verification
For more information about what Maverick Applied Science can do, you can contact us at
+941-721-1800 or see us at www.maverickappliedscience.com. We look forward to putting our
expertise to work for you.

General Notes
1) The following catalog support configurations are designed for the listed allowable loads. If actual load
requirements differ from the defined allowable loads, configurations and materials can be altered to
accommodate the load requirements. The defined vertical loads are downward in direction unless
otherwise noted. Please specify all load requirements with placement of order.
2) The defined support loads and designs are based on typical FRP and plastic pipe/duct system
arrangements, design parameters and spans between supports. Support designs and configurations can
be altered to accommodate specific project needs.
3) Allowable loads for pipe supports are based on 150 PSI rated FRP pipe wall thicknesses. Allowable
loads and designs for duct supports are based on 25 PSI rated FRP wall thicknesses. If the actual
pressure ratings differ, the support designs can be altered to safely distribute the required loading.
4) All supports are designed to maximize load distribution and to avoid point loading of the pipe at the
support.
5) Large diameter supports are custom engineered to meet specific load and functionality requirements.
Expected loads and movements are required to engineer and optimize support configuration and design.
Where large diameter supports are used without slide bearings allowing steel on steel contact, supports
will need to be evaluated for axial loads due to increased frictional loading.
6) Structural and supplementary steel structures are assumed to be near rigid. The length of the support
should be centered on the supporting structures to limit the torsional loading of the steel. Flexibility in
structural steel may induce unanticipated loads into the pipe/duct.
7) The width of the supporting structural steel should be considered for support bearing. Structural or
supplementary steel should provide a bearing surface of at least 50% of the support base length. If this is
not possible, larger or thicker support base plates or stiffeners may be required. If additional installation
plates or larger support base plates are needed, please specify size (length, width and thickness) with
placement of order.
8) Pipe/duct supports are available in sizes up to 60” in diameter. Larger sizes are available and are
designed to suit the project requirements.
9) All pipe/duct sizes are considered nominal. The outer diameter (O.D.) may vary depending on the
manufacturer. The maximum O.D. must be specified with placement of order.
10) Support dimensions are based on typical wall thicknesses and may vary depending on the actual
O.D. and load requirements (See Note 3).
11) Flange support dimensions for sizes up to 24” diameter pipe are based on ANSI B16.5 CL150 flange
drilling and may vary depending on the actual drilling class and load requirements.
12) Flange support dimensions for sizes above 24” diameter pipe are based on ASME B16.47 Series A
CL150 flange drilling and may vary depending on the actual drilling class and load requirements.
13) FRP flanges require a full back facing for use with flange plate supports.
14) The standard material for Maverick supports is carbon steel. Other materials such as aluminum,
stainless steel and other alloys are available upon request.

General Notes
15) The standard finishes for Maverick pipe/duct supports are:

1” to 30” diameter: Hot dipped galvanized
36” diameter and up: Painted per MAS painting specification MAS09900-6.13, Type 2
See Appendix 1
Other types of paint finishes and Mill finish are available upon request. Please specify desired finish with
placement of order.
16) All saddle and clamp type supports include cushioning material to assure best fit and to minimize
exterior pipe wear.
17) Supports that require attachment to a structure are designed for welded installations. If bolted
installations are preferred, please specify details with placement of order. See Support Options (Page 86)
for details.
18) Sizing of field welds for supports, clips, brackets, lugs, etc. to supporting structures are to be
determined by others.
19) Guide clips provided with the non-slide bearing type guide supports are designed to be field welded to
the supporting structure. Guide clips for bolted installations to the supporting structure are available.
Please specify the preferred attachment method with placement of order. See Figure O4 (Page 90) for
details.
20) The standard horizontal gap for guide and linestop supports is 1/8” with factory installed clips.
Supports can be adjusted for specific displacements as required for project needs. Please specify with
placement of order.
21) The upwards vertical gap for our guide and linestop style supports is ±1/8” with factory installed clips..
The vertical gaps of supports with slide bearings may vary depending on the style of clip required. Where
uplift or overturning is a concern, please provide vertical limit requirements or overturning loads at
placement of order and supports can be adjusted to accommodate the specified limits and loads.
22) Slide bearings are recommended for supports with moderate to severe displacements and loads on
systems having long runs with design pressures over 75 PSI for FRP or plastic pipe. Slide bearings are
recommended for piping systems above 10” diameter where temperature gradients from ambient are
greater than 60°F may occur. See Figure O2 (Page 88) for details. The incorporation of slide bearings is
to minimize loads transferred to the supporting structure.
23) If pipe/duct requires insulation, slots can be incorporated into the support design to accommodate
insulation banding. Please specify insulation thickness and details at placement of order.
24) Supplementary steel supporting structures are not included with Maverick supports. Supplementary
supporting structures can be provided upon request.
25) All materials such as pipe, duct, flanges and shear collars are not included with Maverick supports.
This material should be sourced from the piping manufacturer.
26) Shield banding and buckles are not included with Maverick supports. Banding and buckles can be
provided upon request. Material will be provided in bulk form.
27) Hanger hardware to suspend a support from a structure above is not included with Maverick
supports. Hanging hardware can be provided upon request.

Pictorial Index
Pipe Supports
S1 S2 S4
U-Strap W/ Shield U-Bolt W/ Shield Clevis Hanger
(1” – 12” Diameter) (1” – 12” Diameter) (1” – 18” Diameter)
S5 S5 S7
Wide Clamp Hanger Wide Clamp Hanger FRP Wear Pad
S8 S9 S9B
Slide Shield Pipe Cradle Pipe Cradle

Pictorial Index
Pipe Supports
S10 S11 S12

Pipe Stand – Fixed Height Pipe Stand – Adjustable Flange Slide
(1” – 8” Diameter) Height (1” – 8” Diameter) (1” – 10” Diameter)
S12B S12B S13

Flange Slide Flange Slide Flange Guide
S13B S13B S14

Flange Guide Flange Guide Flange Anchor

Pictorial Index
Pipe Supports
S14 S15 S15B

Flange Anchor Flange Linestop Flange Linestop
S15B S16 S17

Flange Linestop Flange Hanger Flange Riser Guide
S17 S18 S19

Flange Riser Guide Flange Riser Support Flange Riser Support W/
(36” – 60” Diameter) (12” – 60” Diameter) Guides (12” – 60” Diameter)
Pictorial Index
Pipe Supports
P7 P7B P8
Elbow Support Slide Plate Elbow Support Slide Plate Base Slide
P8L P9 P9L
Base Slide – Low Profile Base Guide Base Guide – Low Profile
P10 P10L P13

Base Anchor Base Anchor – Low Profile Riser Guide

Pictorial Index
Pipe Supports
P13 P14 P14

Riser Guide Riser Support Riser Support
P14 P15 P15

Riser Support Double Rod Riser Hanger Double Rod Riser Hanger
P16 P16 P16

Riser Support W/ Guides Riser Support W/ Guides Riser Support W/ Guides

Pictorial Index
Pipe Supports
P17 P17 P18

Base Linestop Base Linestop Base Slide
P18 P19 P19

Base Slide Base Guide Base Guide
P20 P20
Base Anchor Base Anchor
(12” – 30” Diameter) (36” – 60” Diameter)

Pictorial Index
Pipe Supports
XL12 XL13
Extra Large Slide Extra Large Guide
XL14
Extra Large Anchor
(66” – 108” Diameter)

Pictorial Index
Duct Supports
D1 D3 D4
Duct Clamp Hanger Duct Cradle Base Slide Duct Base Linestop
D4 D5 D5
Duct Base Linestop Duct Base Slide Duct Base Slide
D6 D6 D7
Duct Base Guide Duct Base Guide Duct Base Anchor

Pictorial Index
Duct Supports
D7 D16
Duct Base Anchor Duct Riser Guide
D16 D17
Duct Riser Guide Duct Riser Support W/ Guides
D17
Duct Riser Support W/ Guides
(36” – 60” Diameter)

Maverick Applied Science, Inc.
Pipe Supports

Figure S1: U-Strap W/ Shield
(2) 180 DEG 'L2'

LOAD SHIELD
'L1'
1/8" GAP
'C'
ELASTOMERIC
CUSHION
T.O.S. B.O.P.
BANDING
(SEE NOTES)
FASTENER 'G' 'W'

(NOT INCLUDED)
Finish: Notes:
Electroplated, hot-dipped galvanized Base width (W) must be fully supported. Dimensions
See General Note 15, page 4. are based on typical 150 PSI rated pipe and may
vary depending on the actual O.D. and load
Service: requirements. Load shield rests on supporting
To provide wear protection for pipe while allowing structure. Banding can be provided in bulk upon
freedom of axial movement and limiting lateral request. See General Notes, pages 3 and 4.
movement
Material:
Carbon steel
See General Note 14, page 3.
Pipe Size C G L1 L2 W Allowable Loads [lb]

[in] [in] [in] [in] [in] [in] Lateral Vertical
1 1 1/2 3/8 3 12 3 7/8 80 80
1 1/2 1 1/2 3/8 3 12 4 3/8 90 90
2 2 3/8 4 12 5 3/8 100 110
3 2 3/8 4 12 6 3/8 200 200
4 2 3/8 4 12 7 1/2 300 280
6 2 1/2 4 12 9 7/8 600 540
8 2 1/2 4 12 11 7/8 700 800
10 2 1/2 5/8 6 12 14 1/2 1300 1200
12 2 1/2 5/8 6 12 16 3/4 1300 1600

Figure S2: U-Bolt W/ Shield
BANDING
(SEE NOTES)
(2) 180 DEG
LOAD SHIELD
1/8" GAP
U-BOLT
'D'
ELASTOMERIC
CUSHION
'B'
B.O.P.
T.O.S. 'A'
(4) HEX NUTS 'W' 'L1'

AND WASHERS
Finish: Notes:
Electroplated, hot-dipped galvanized Base width (W) must be fully supported. Dimensions
Service: requirements. Load shield rests on supporting
To provide wear protection for pipe while allowing structure. Banding can be provided in bulk upon
freedom of axial movement and limiting lateral request. See General Notes, pages 3 and 4.
movement
Material:
Carbon steel
Pipe Size A B D L1 W Allowable Loads [lb]

[in] [in] [in] [in] [in] [in] Lateral Vertical
1 1 3/4 2 3/8 12 2 3/8 20 80
1 1/2 1 7/8 2 1/4 3/8 12 2 7/8 20 90
2 2 1/4 2 3/4 3/8 12 3 3/8 20 110
3 3 3 1/2 1/2 12 4 1/2 45 200
4 3 4 1/2 12 5 5/8 70 280
6 3 1/2 5 1/2 5/8 12 8 150 540
8 3 1/2 6 1/2 5/8 12 10 170 800
10 4 8 3/4 12 12 1/4 200 1200
12 4 1/2 9 1/2 3/4 12 14 1/2 210 1600

Figure S4: Clevis Hanger
HANGING HARDWARE
(NOT INCLUDED)
'D'
'H'
LOAD SHIELD
REQUIRED FOR
14" NPS AND
ABOVE
ELASTOMERIC
CUSHION 'L1'
'L2'
Finish: Notes:
Hot-dipped galvanized Dimensions are based on typical 150 PSI rated pipe
See General Note 15, page 4. and may vary depending on the actual O.D. and load
requirements. Hanging hardware is available upon
Service: request. See General Notes, pages 3 and 4.
To support weight of pipe from above while
allowing freedom of movement
Material:
Carbon steel
Pipe Size D H L1 L2 Allowable Loads [lb]

[in] [in] [in] [in] [in] Vertical
1 3/8 3 1/4 3 ----- 100
1 1/2 3/8 3 1/4 3 ----- 150
2 3/8 3 1/4 3 ----- 240
3 1/2 4 1/2 3 ----- 315
4 5/8 5 1/2 3 ----- 420
6 3/4 7 4 ----- 840
8 3/4 8 1/2 4 ----- 1120
10 7/8 10 6 ----- 1800
12 7/8 11 1/2 6 ----- 2160
14 1 12 1/2 4 8 2800
16 1 14 4 8 3300
18 1 16 4 10 3500

Figure S5: Wide Clamp Hanger
HANGING HARDWARE
(NOT INCLUDED)
'D'
PIN 'P'
(NOT INCLUDED)
ELASTOMERIC
CUSHION
'H'
'C'
'L1'
Finish: Notes:
requirements. Hanging hardware is available upon
Service: request. See page 19 for sizes 20” - 60”. See
To support weight of pipe from above while General Notes, pages 3 and 4.
Material:
Carbon steel
Pipe Size C D H L1 P Allowable Loads [lb]

[in] [in] [in] [in] [in] [in] Vertical
1 1 1/2 3/8 4 3 1/2 100
1 1/2 1 1/2 3/8 4 1/4 3 1/2 150
2 1 1/2 3/8 4 9/16 3 1/2 240
3 1 1/2 1/2 5 1/16 3 5/8 315
4 1 1/2 5/8 5 9/16 3 3/4 420
6 2 3/4 6 3/4 4 7/8 840
8 2 3/4 7 3/4 4 7/8 1120
10 2 1/2 7/8 9 1/16 6 1 1800
12 2 1/2 7/8 10 1/8 6 1 2160
14 2 1/2 1 11 1/4 8 1 1/8 3360
16 2 1/2 1 12 7/16 8 1 1/8 3840
18 3 1 13 11/16 10 1 1/8 5400

Figure S5: Wide Clamp Hanger
HANGING HARDWARE
'D' (NOT INCLUDED)
PIN 'P'
(NOT INCLUDED)
ELASTOMERIC
CUSHION
'H'
'C'
'L1'
Finish: Notes:
20” – 30”: Hot-dipped galvanized Dimensions are based on typical 150 PSI rated pipe
36” – 60”: Painted and may vary depending on the actual O.D. and load
See General Note 15, page 4. requirements. Hanging hardware is available upon
request. See page 18 for sizes 1” - 18”. See General
Service: Notes, pages 3 and 4.
To support weight of pipe from above while
Material:
Carbon steel

20 3 1 1/4 15 3/4 10 1 3/8 8000
24 3 1 1/2 18 3/16 12 1 5/8 10000
30 3 2 22 15 2 1/4 15000
36 4 2 1/4 26 18 2 1/2 23000
42 4 2 1/2 30 3/8 21 2 3/4 28000
48 4 2 3/4 35 1/4 24 3 36000
54 4 3 37 3/16 27 3 1/4 40000
60 4 3 40 1/4 30 3 1/4 45000

Figure S7: FRP Wear Pad
180 DEG WEAR PAD
B.O.P.
T.O.S.
FIELD ADHESIVE
BOND
'L1'
Finish: Notes:
Plain, painted Bonded to FRP pipe. Adhesive to be ordered
separately. Wear pad rests on supporting structure.
Service: See General Notes, pages 3 and 4.
To provide wear protection for FRP pipe while
Material:
Fiberglass reinforced plastic
Pipe Size L1 Allowable Loads [lb]

[in] [in] Vertical
1 4 50
1 1/2 4 60
2 4 75
3 6 130
4 6 180
6 8 350
8 8 520
10 10 780
12 12 1200

Figure S8: Slide Shield
BANDING
(SEE NOTES)
180 DEG
LOAD SHIELD
B.O.P.
T.O.S.
ELASTOMERIC
CUSHION
'L1'
Finish: Notes:
Electroplated, hot-dipped galvanized Dimensions are based on typical 150 PSI rated pipe
requirements. Load shield rests on supporting
Service: structure. Banding can be provided in bulk upon
To provide wear protection for pipe while allowing request. See General Notes, pages 3 and 4.
freedom of movement
Material:
Carbon steel
Pipe Size L1 Allowable Loads [lb]

[in] [in] Vertical
1 12 80
1 1/2 12 90
2 12 110
3 12 200
4 12 280
6 12 540
8 12 800
10 12 1200
12 12 1600

Figure S9: Pipe Cradle
BANDING
(SEE NOTES) 'L1'
ELASTOMERIC
CUSHION
B.O.P.
1 1/2"
T.O.S.
'W' 'L2'
Finish: Notes:
requirements. Banding can be provided in bulk upon
Service: request. See page 23 for sizes 12” – 60”. See
To support weight of pipe while allowing freedom General Notes, pages 3 and 4.
of movement
Material:
Carbon steel.
Pipe Size L1 L2 W Allowable Loads [lb]

[in] [in] [in] [in] Vertical
1 6 4 4 1/2 120
1 1/2 6 4 5 150
2 8 4 4 170
3 8 4 4 1/2 250
4 8 4 5 1/2 320
6 10 6 7 1/2 650
8 10 6 9 1/2 1000
10 10 6 11 1/4 1500

Figure S9B: Pipe Cradle
BANDING 'L1'
(SEE NOTES)
ELASTOMERIC
CUSHION
B.O.P.
'H'
T.O.S.
PTFE SLIDE 'L3'

'W' BEARINGS
(2) PLACES 'L2'
Finish: Notes:
20” – 30”: Hot-dipped galvanized Support is provided with a base plate for welded
36” – 60”: Painted installations. Base plates for bolted installation are
See General Note 15, page 4. available upon request. Provide bolting arrangement
with placement of order. Dimensions are based on
Service: typical 150 PSI rated pipe and may vary depending
To support weight of pipe while allowing freedom on the actual O.D. and load requirements. PTFE
of movement slide bearings are recommended for pipe sizes
above 10” NPS. Banding can be provided in bulk
Material: upon request. See page 22 for sizes 1” – 10”. See
Carbon steel General Notes, pages 3 and 4.
Pipe Size H L1 L2 L3 W Allowable Loads [lb]

12 3 12 8 8 13 1/8 1800
14 3 12 8 8 15 2400
16 3 12 8 8 16 1/2 3000
18 3 12 8 8 19 3700
20 3 1/4 12 8 8 21 4300
24 3 1/4 14 10 8 25 6200
30 4 16 12 10 30 9000
36 8 20 16 12 36 13000
42 8 22 18 12 42 16000
48 8 24 20 12 48 23000
54 8 26 22 12 54 28000
60 8 28 24 12 60 32000

Figure S10: Pipe Stand – Fixed Height
'C' 'L1'
ELASTOMERIC
CUSHION
B.O.P.
'D'
2" MIN
12" MAX
T.O.S.
'L2' 'L2'
Finish: Notes:
Hot-dipped galvanized Not designed for axial or lateral loads. Dimensions
Service: requirements. Specify desired height upon placement
Fixed height pipe stand to support weight of pipe of order. See General Notes, pages 3 and 4.
while allowing freedom of movement
Material:
Carbon steel
Pipe Size C D L1 L2 Allowable Loads [lb]

[in] [in] [NPS] [in] [in] Vertical
1 1 1/2 1 1/2 3 6 150
1 1/2 1 1/2 1 1/2 3 6 180
2 1 1/2 2 3 6 220
3 1 1/2 2 3 6 320
4 1 1/2 2 3 6 420
6 2 3 4 8 800
8 2 3 4 8 1050
Maverick Applied Science, Inc. 5Th Edition Page 24

Figure S11: Pipe Stand – Adjustable Height
'C' 'L1'
ELASTOMERIC
CUSHION
B.O.P.
'D'
3" MIN
'E'
6" MIN
12" MAX
T.O.S.
'L2' 'L2'
Finish: Notes:
Hot-dipped galvanized Not designed for axial or lateral loads. Dimensions
Service: requirements. Specify desired height upon placement
Adjustable height pipe stand to support weight of of order. See General Notes, pages 3 and 4.
pipe while allowing freedom of movement
Material:
Carbon steel
Pipe Size C D E L1 L2 Allowable Loads [lb]

[in] [in] [NPS] [NPS] [in] [in] Vertical
1 1 1/2 1 1/2 2 3 6 150
1 1/2 1 1/2 1 1/2 2 3 6 180
2 1 1/2 2 1/2 3 4 6 220
3 1 1/2 2 1/2 3 4 6 320
4 1 1/2 2 1/2 3 4 6 420
6 2 4 5 5 8 800
8 2 4 5 5 8 1050

Figure S12: Flange Slide
'H'
T.O.S.
'W' 'L2'
'L1'
Finish: Notes:
Hot-dipped galvanized Dimensions are based on ANSI B16.5 CL150 flange
See General Note 15, page 4. drilling and may vary depending on actual drilling
requirements. FRP flanges require a full back-face.
Service: See page 27 for sizes 12” – 30”. See page 28 for
To support weight of pipe, valves or equipment sizes 36” – 60”. See General Notes, pages 3 and 4.
while allowing freedom of movement
Material:
Carbon steel
Pipe Size H L1 L2 W Allowable Loads [lb]

1 3 3/4 3 1 1/4 5 1/2 200
1 1/2 4 1/4 3 1 1/4 6 300
2 4 5/8 4 1 3/4 6 500
3 5 1/4 4 1 3/4 7 1/2 700
4 6 4 1 3/4 10 1/4 900
6 7 6 2 3/4 12 1/4 1500
8 8 1/4 6 2 3/4 14 1/4 1800
10 9 3/8 8 3 3/4 17 1/4 2200

Figure S12B: Flange Slide
'H'
T.O.S.
PTFE SLIDE
BEARINGS
(2) PLACES 'W' 'L2'
'L1'
Finish: Notes:
Hot-dipped galvanized Support is provided with a base plate for welded
See General Note 15, page 4. installations. Base plates for bolted installations are
available upon request. Provide bolting arrangement
Service: with placement of order. Dimensions are based on
To support weight of pipe, valves or equipment, ANSI B16.5 or ASME B16.47 Series A CL 150 flange
while allowing freedom of movement drilling and may vary depending on actual drilling
requirements. PTFE slide bearings are
Material: recommended for pipe sizes above 10” NPS. FRP
Carbon steel flanges require a full back-face. See page 26 for
See General Note 14, page 3. sizes 1”–10”. See page 28 for sizes 36” – 60”. See
General Notes, pages 3 and 4.

12 12 8 3 3/4 20 2800
14 12 7/8 8 3 3/4 21 1/2 3200
16 14 1/8 8 3 3/4 24 1/2 4200
18 15 3/8 8 3 3/4 26 5300
20 17 1/2 10 4 5/8 29 1/8 6500
24 19 3/4 10 4 5/8 32 3/4 8900
30 23 5/8 10 4 5/8 36 3/4 11000

Figure S12B: Flange Slide
'H'
T.O.S.
PTFE SLIDE
BEARINGS 'W' 'L2'
(2) PLACES
'L1'
Finish: Notes:
Painted Support is provided with a base plate for welded
To support weight of pipe, valve or equipment ASME B16.47 Series A CL 150 and may vary
while allowing freedom of movement depending on actual drilling requirements. PTFE
slide bearings are recommended for pipe sizes
Material: above 10” NPS. FRP flanges require a full back-face.
Carbon steel See page 26 for sizes 1” – 10”. See page 27 for 12” –
See General Note 14, page 3. 30”. See General Notes, pages 3 and 4.

36 26 3/4 12 10 49 3/4 13000
42 30 1/4 14 12 56 3/4 18000
48 33 1/2 16 14 63 3/4 24000
54 38 1/2 18 16 72 30000
60 42 20 18 78 1/2 36000

Figure S13: Flange Guide
'H'
T.O.S.
'W' 'L2'
'L1'
Finish: Notes:
Hot-dipped galvanized Type FB1 welded guide clips are provided with this
See General Note 15, page 4. style of support. Type FB2 bolted guide clips are
available upon request. Dimensions are based on
Service: ANSI B16.5 CL 150 flange drilling and may vary
To support weight of pipe, valves or equipment, depending on actual drilling requirements. Can also
while allowing freedom of axial movement and be used as a flange riser guide. FRP flanges require
limiting lateral movement a full back-face. See page 30 for sizes 12” – 30”. See
page 31 for sizes 36” – 60”. See General Notes,
Material: pages 3 and 4.
Carbon steel

[in] [in] [in] [in] [in] Lateral Vertical
1 3 3/4 3 1 1/4 7 3/4 100 200
1 1/2 4 1/4 3 1 1/4 8 1/4 150 300
2 4 5/8 4 1 3/4 8 1/4 200 500
3 5 1/4 4 1 3/4 9 3/4 280 700
4 6 4 1 3/4 12 1/2 360 900
6 7 6 2 3/4 14 1/2 600 1500
8 8 1/4 6 2 3/4 16 1/2 720 1800
10 9 3/8 8 3 3/4 19 1/2 880 2200

Figure S13B: Flange Guide
'H'
T.O.S.
PTFE SLIDE 'W' 'L2'

BEARINGS 'L1'
(2) PLACES
Finish: Notes:
To support weight of pipe, valves or equipment, ANSI B16.5 or ASME B16.47 Series A CL 150 flange
while allowing freedom of axial movement and drilling and may vary depending on actual drilling
limiting lateral movement requirements. PTFE slide bearings are
recommended for pipe sizes above 10” NPS. FRP
Material: flanges require a full back-face. See page 29 for
Carbon steel sizes 1”–10”. See page 31 for sizes 36” – 60”. See
See General Note 14, page 3. General Notes, pages 3 and 4.

12 12 8 3 3/4 24 1/2 1120 2800
14 12 7/8 8 3 3/4 26 1280 3200
16 14 1/8 8 3 3/4 28 1680 4200
18 15 3/8 8 3 3/4 30 1/2 2100 5300
20 17 1/2 10 4 5/8 33 5/8 2600 6500
24 19 3/4 10 4 5/8 37 1/4 3600 8900
30 23 5/8 10 4 5/8 41 1/4 4400 11000

Figure S13B: Flange Guide
'H'
T.O.S.
PTFE SLIDE 'W' 'L2'

BEARINGS
(2) PLACES 'L1'
Finish: Notes:
To support weight of pipe, valves or equipment, ASME B16.47 Series A CL 150 flange drilling and
while allowing freedom of axial movement and may vary depending on actual drilling requirements.
limiting lateral movement PTFE slide bearings are recommended for pipe sizes
above 10” NPS. FRP flanges require a full back-face.
Material: See page 29 for sizes 1”–10”. See page 30 for sizes
Carbon steel 12” – 30”. See General Notes, pages 3 and 4.

36 26 3/4 12 10 57 3/4 9100 13000
42 30 1/4 14 12 64 3/4 12600 18000
48 33 1/2 16 14 73 3/4 16800 24000
54 38 1/2 18 16 80 3/8 21000 30000
60 42 20 18 87 25000 36000

Figure S14: Flange Anchor
'H'
T.O.S.
'W' 'L2'
'L1'
Finish: Notes:
Service: with placement of order. FRP flanges require a full
To support weight of pipe, valves or equipment back-face. Dimensions are based on ANSI B16.5 or
while restricting all movement ASME B16.47 Series A CL 150 flange drilling and
may vary depending on actual drilling requirements.
Material: Can also be used as a flange riser anchor. See page
Carbon steel 33 for sizes 36” – 60”. See General Notes, pages 3
See General Note 14, page 3. and 4.

[in] [in] [in] [in] [in] Lateral Vertical Axial
1 3 3/4 4 1 3/4 5 1/2 100 200 300
1 1/2 4 1/4 4 1 3/4 5 7/8 150 300 320
2 4 5/8 6 2 3/4 7 1/2 200 500 350
3 5 1/4 6 2 3/4 9 280 700 490
4 6 6 2 3/4 10 1/2 360 900 630
6 7 8 3 3/4 12 1/2 600 1500 1260
8 8 1/4 8 3 3/4 15 720 1800 1800
10 9 3/8 10 4 3/4 18 880 2200 2100
12 12 10 4 3/4 20 1/2 1120 2800 2400
14 12 7/8 10 4 3/4 22 1/2 1280 3200 3000
16 14 1/8 12 5 3/4 25 1/4 1680 4200 4200
18 15 3/8 12 5 5/8 26 7/8 2100 5300 5300
20 17 1/2 12 5 5/8 30 1/4 2600 6500 6500
24 19 3/4 12 5 5/8 34 3600 8900 7000
30 23 5/8 12 5 5/8 42 4400 11000 7500

Figure S14: Flange Anchor
'H'
T.O.S.
'W' 'L1'
Finish: Notes:
Service: with placement of order. FRP flanges require a back-
To support weight of pipe, valves or equipment face. Dimensions are based on ASME B16.47 Series
while restricting all movement a CL 150 and may vary depending on actual drilling
requirements. See page 32 for sizes 1” – 30”. See
Material: General Notes, pages 3 and 4.
Carbon steel
Pipe Size H L1 W Allowable Loads [lb]

[in] [in] [in] [in] Lateral Vertical Axial
36 26 3/4 12 49 3/4 9100 13000 8000
42 30 1/4 14 56 3/4 12600 18000 9100
48 33 1/2 16 63 3/4 16800 24000 12000
54 38 1/2 18 72 21000 30000 15000
60 42 20 78 1/2 25000 36000 18000

Figure S15: Flange Linestop
'H'
T.O.S.
'W' 'L2'
'L1'
Finish: Notes:
Hot-dipped galvanized If axial and lateral displacements are to be limited,
See General Note 15, page 4. request optional base plate type BP4, page 89. Base
width (W) and length (L1) must be fully supported.
Service: Support is provided with a base plate for welded
To support weight of pipe, valves or equipment, installations. Base plates for bolted installations are
while allowing freedom of lateral movement and available upon request. Provide bolting arrangement
limiting axial movement with placement of order. FRP flanges require a full
back-face. Dimensions are based on ANSI B16.5 CL
Material: 150 flange drilling and may vary depending on actual
Carbon steel drilling requirements. See page 35 for sizes 12” –
See General Note 14, page 3. 30”. See page 36 for sizes 36” – 60”. See General
Notes, pages 3 and 4.

[in] [in] [in] [in] [in] Vertical Axial
1 3 3/4 8 1/4 1 3/4 5 1/2 200 300
1 1/2 4 1/4 8 1/4 1 3/4 5 7/8 300 320
2 4 5/8 10 1/2 2 3/4 7 1/2 500 350
3 5 1/4 10 1/2 2 3/4 9 700 490
4 6 10 1/2 2 3/4 10 1/2 900 630
6 7 14 3 3/4 12 1/2 1500 1260
8 8 1/4 14 3 3/4 15 1800 1800
10 9 3/8 16 4 3/4 18 2200 2100

Figure S15B: Flange Linestop
'H'
T.O.S.
PTFE SLIDE 'W' 'L2'

BEARINGS 'L1'
(2) PLACES
Finish: Notes:
Hot-dipped galvanized If axial and lateral displacements are to be limited,
To support weight of pipe, valves or equipment, installation. Base plates for bolted installations are
back-face. Dimensions are based on ANSI B16.5 or
Material: ASME B16.47 Series A CL 150 flange drilling and
Carbon steel may vary depending on actual drilling requirements.
See General Note 14, page 3. PTFE slide bearings are recommended for pipe sizes
above 10” NPS. See page 34 for sizes 1” – 10”. See
pages 3 and 4.

12 12 16 4 3/4 20 1/2 2800 2400
14 12 7/8 16 4 3/4 22 1/2 3200 3000
16 14 1/8 18 5 3/4 25 1/4 4200 4200
18 15 3/8 18 5 5/8 26 7/8 5300 5300
20 17 1/2 18 5 5/8 30 1/4 6500 6500
24 19 3/4 18 5 5/8 34 8900 7000
30 23 5/8 18 5 5/8 42 11000 7500

Figure S15B: Flange Linestop
'H'
T.O.S.
PTFE SLIDE 'W' 'L2'

BEARINGS
(2) PLACES 'L1'
Finish: Notes:
Painted If axial and lateral displacements are to be limited,
To support weight of pipe, valves or equipment, installation. Base plates for bolted installations are
back-face. Dimensions are based on ASME B16.47
Material: Series A CL 150 flange drilling and may vary
Carbon steel depending on actual drilling requirements. PTFE
See General Note 14, page 3. slide bearings are recommended for pipe sizes
above 10” NPS. See page 34 for sizes 1” – 10”. See
pages 3 and 4.

36 26 3/4 21 15 49 3/4 13000 8000
42 30 1/4 23 17 56 3/4 18000 9100
48 33 1/2 25 19 63 3/4 24000 12000
54 38 1/2 27 21 72 30000 15000
60 42 29 23 78 1/2 36000 18000

Figure S16: Flange Hanger
HANGING HARDWARE
'D' (NOT INCLUDED)
PIN 'P'
(NOT INCLUDED)
'H'
'W'
Finish: Notes:
Hot-dipped galvanized Dimensions are based on ANSI B16.5 CL 150 flange
See General Note 15, page 4. drilling and may vary depending on actual drilling
requirements. FRP flanges require full back-face.
Service: Hanging hardware is available upon request. See
To support weight of pipe, valves or equipment General Notes, pages 3 and 4.
from above while allowing freedom of movement
Material:
Carbon steel
Pipe Size H D P W Allowable Loads [lb]

1 4 1/8 3/8 1/2 4 1/4 250
1 1/2 4 1/2 3/8 1/2 5 450
2 5 3/8 1/2 6 600
3 6 1/2 5/8 7 1/2 1100
4 6 1/2 5/8 3/4 9 1600
6 7 1/2 3/4 7/8 11 2200
8 9 3/4 7/8 14 2800
10 10 7/8 1 16 3200
12 12 7/8 1 19 3600
14 13 1 1 1/8 21 4000
16 14 1 1 1/8 24 4500
18 15 1 1 1/8 25 5300

Figure S17: Flange Riser Guide
'N'
FIELD SET
GAP
'L2'
A A
T.O.S.
1" FIELD
SET GAP
SECTION A-A
'L1' 'W'
(TYP)
Finish: Notes:
Painted Not designed for vertical loading. Support width (W)
See General Note 15, page 4. is based on listed allowable loads. For a greater
width, the support configuration may need to be
Service: adjusted to suit listed allowable loads. Type RGC1
To allow axial movement while limiting lateral welded riser guide clips are provided with this style of
movement support. Type RGC2 bolted riser guide clips are
available upon request, page 91. Dimensions are
Material: based on ASME B16.47 Series A CL 150 flange
Carbon steel drilling and may vary depending on actual drilling
See General Note 14, page 3. requirements. FRP flanges require full back-face.
See page 38 for sizes 36” – 60”. See General Notes,
pages 3 and 4.
Pipe Size L1 L2 N # Of W Allowable Loads [lb]

[in] [in] [in] Holes [in] Lateral
36 6 17 1/2 16 53 9100
42 6 26 3/4 24 60 10500
48 6 24 1/2 24 66 1/2 12000
54 8 27 3/4 24 73 1/4 13500
60 8 34 32 80 15000

Figure S18: Flange Riser Support
A A
'H'
T.O.S.
'W'
(TYP)
SECTION A-A
Finish: Notes:
12” – 30”: Hot-dipped galvanized Support width (W) is based on listed allowable loads.
36” – 60”: Painted For a greater width, the support configuration may
See General Note 15, page 4. need to be adjusted to suit listed allowable loads. If a
fixed anchor type support is required, provide loads
Service: for evaluation. FRP flanges require a full back-face.
To support weight of pipe while allowing freedom Dimensions are based on ANSI B16.5 or ASME
of lateral movement. May also be configured to B16.47 Series A CL 150 flange drilling and may vary
restrict all movement depending on actual drilling requirements. See
General Notes, pages 3 and 4.
Material:
Carbon steel
Pipe Size H W Allowable Loads [lb]

[in] [in] [in] Vertical
12 4 25 5800
14 4 27 6300
16 4 29 1/2 6900
18 4 31 7600
20 6 33 1/2 12000
24 6 38 15000
30 6 46 3/4 18000
36 6 54 24000
42 6 61 30000
48 8 67 1/2 36000
54 8 74 1/4 48000
60 8 81 60000

Figure S19: Flange Riser Support W/ Guides
FIELD SET
GAP 'L2'
A A
'H'
T.O.S.
'W'
SECTION A-A (TYP)
'L1'
Finish: Notes:
12” – 30”: Hot-dipped galvanized Support width (W) is based on listed allowable loads.
36” – 60”: Painted For a greater width, the support configuration may
See General Note 15, page 4. need to be adjusted to suit listed allowable loads.
Type RC1 welded riser guide clips are provided with
Service: this style support. Type RGC2 bolted riser guide clips
To support weight of pipe while limiting lateral are available upon request, page 91. Dimensions are
movement based on ANSI B16.5 or ASME B16.47 Series A CL
150 flange drilling and may vary depending on actual
Material: drilling requirements. FRP flanges require a full back-
Carbon steel face. See General Notes, pages 3 and 4.

12 4 4 4 25 3300 5800
14 4 4 4 27 3600 6300
16 4 4 6 29 1/2 4000 6900
18 4 4 6 31 4400 7600
20 6 4 8 33 1/2 5800 12000
24 6 4 8 38 6600 15000
30 6 4 12 46 3/4 8000 18000
36 6 6 12 54 9100 24000
42 6 6 12 61 12600 30000
48 8 8 12 67 1/2 16800 36000
54 8 8 18 74 1/4 21000 48000
60 8 8 18 81 25000 60000

Figure P7: Elbow Support Slide Plate
'D'
'A'
'BC'
SUPPORT LEG AND

FLANGE TO BE
ENGINEERED AND
PROVIDED BY PIPE
MANUFACTURER
T.O.S.
Finish: Notes:
Hot-dipped galvanized Bending moments should be evaluated at the
See General Note 15, page 4. connection to elbow. Provide support leg flange
thickness when ordering. See General Notes, pages
Service: 3 and 4.
To carry pipe weight while allowing freedom of
movement
Material:
Carbon steel
Elbow A BC D
Size [in] [in] [in] [in]
2 2 4 3/4 6
3 3 6 7 1/2
4 3 6 7 1/2
6 4 7 1/2 9
8 6 9 1/2 11
10 6 9 1/2 11

Figure P7B: Elbow Support Slide Plate
'D'
'A'
'BC'
SUPPORT LEG AND

FLANGE TO BE
ENGINEERED AND
PROVIDED BY PIPE
MANUFACTURER
T.O.S.
15/16"
PTFE SLIDE
BEARINGS
Finish: Notes:
Hot-dipped galvanized Bending moments should be evaluated at the
See General Note 15, page 4. connection to elbow. Provide support leg flange
thickness when ordering. PTFE slide bearings are
Service: recommended for pipe sizes above 10” NPS.
To carry pipe weight while allowing freedom of Support is provided with a base plate for welded
movement installations. Base plates for bolted installations are
Material: with placement of order. See General Notes, pages 3
Carbon steel and 4.
See General Note 14 page 3.
Elbow A BC D
Size [in] [in] [in] [in]
12 8 11 3/4 13 1/2
14 10 14 1/4 16
16 10 14 1/4 16
18 12 17 19
20 14 18 3/4 21
24 16 21 1/4 23 1/2

Figure P8: Base Slide
'L1'
ELASTOMERIC
CUSHION
'C' 0-20 DEG
B.O.P.
1 1/2" T.O.S.
'W'
Finish: Notes:
Hot-dipped galvanized Dimensions are estimated based on typical 150 PSI
See General Note 15, page 4. rated pipe and may vary depending on the actual
O.D. and load requirements. See General Notes,
Service: pages 3 and 4.
To support weight of pipe while allowing freedom
of movement
Material:
Carbon steel
Pipe Size C L1 W Allowable Loads [lb]

1 1 1/2 3 4 3/8 150
1 1/2 1 1/2 3 4 1/2 200
2 1 1/2 3 4 3/4 300
3 1 1/2 3 6 1/4 430
4 1 1/2 3 6 1/2 550
6 2 4 8 7/8 1090
8 2 4 10 3/4 1440
10 2 1/2 5 13 1/2 2000

Figure P8L: Base Slide – Low Profile
ELASTOMERIC 'L1'
CUSHION
'C'
B.O.P.
T.O.S.
'W'
Finish: Notes:
Hot-dipped galvanized Base width (W) must be fully supported as shown.
See General Note 15, page 4. Lower saddle rests on supporting structure.
Dimensions are estimated based on typical 150 PSI
Service: rated pipe and may vary depending on the actual
To support weight of pipe while allowing freedom O.D. and load requirements. See General Notes,
of movement pages 3 and 4.
Material:
Carbon steel

1 1 1/2 3 4 3/8 150
1 1/2 1 1/2 3 4 1/2 200
2 1 1/2 3 5 3/4 300
3 1 1/2 3 6 1/4 430
4 1 1/2 3 7 5/8 530
6 2 4 10 5/8 1090
8 2 4 11 3/4 1440
10 2 1/2 5 16 1/8 2000

Figure P9: Base Guide
ELASTOMERIC 'L1'
CUSHION
'C' 0-20 DEG
B.O.P.
1 1/2" T.O.S.
FIELD SET 'W'

GAP
Finish: Notes:
Hot-dipped galvanized Type FB1 welded guide clips are provided with this
See General Note 15, page 4. style of support. Type FB2 bolted guide clips are
available upon request, page 90. Dimensions are
Service: based on typical 150 PSI rated pipe and may vary
To support weight of pipe while allowing freedom depending on the actual O.D. and load requirements.
of axial movement and limiting lateral movement See General Notes, pages 3 and 4.
Material:
Carbon steel

[in] [in] [in] [in] Lateral Vertical
1 1 1/2 3 4 3/8 80 150
1 1/2 1 1/2 3 4 1/2 100 200
2 1 1/2 3 4 3/4 130 270
3 1 1/2 3 6 1/4 190 380
4 1 1/2 3 6 1/2 240 500
6 2 4 8 7/8 480 980
8 2 4 10 3/4 650 1280
10 2 1/2 5 13 1/2 800 2000

Figure P9L: Base Guide – Low Profile
ELASTOMERIC 'L1'
CUSHION
'C'
B.O.P.
T.O.S.
FIELD SET 'W'

GAP
Finish: Notes:
See General Note 15, page 4. Lower saddle rests on supporting structure. Type
FB1 welded guide clips are provided with this style of
Service: support. Type FB2 bolted guide clips are available
To support weight of pipe while allowing freedom upon request, page 90. Dimensions are based on
of axial movement and limiting lateral movement typical 150 PSI rated pipe and may vary depending
on the actual O.D. and load requirements. See
Carbon steel

1 1 1/2 3 5 3/8 80 150
1 1/2 1 1/2 3 4 1/2 100 200
2 1 1/2 3 6 3/4 130 270
3 1 1/2 3 6 1/4 190 380
4 1 1/2 3 7 5/8 240 500
6 2 4 10 5/8 480 980
8 2 4 11 3/4 650 1280
10 2 1/2 5 16 1/8 800 2000

Figure P10: Base Anchor
FRP SHEAR COLLARS 'L1'

ELASTOMERIC (NOT INCLUDED)
CUSHION
'C' 0-20 DEG
B.O.P.
1 1/2" T.O.S.
'W'
Finish: Notes:
Hot-dipped galvanized Support is provided with a base sized for a welded
See General Note 15, page 4. installation. A bolted installation is available upon
request. Provide bolting arrangement with placement
Service: of order. If limiting axial displacement is required,
To support weight of pipe while restricting all request linestop clips type LS1 or LS2 with
movement placement of order. Dimensions are based on typical
150 PSI rated pipe and may vary depending on the
Material: actual O.D. and load requirements. See General
Carbon steel Notes, pages 3 and 4.

1 1 1/2 3 4 3/8 80 150 350
1 1/2 1 1/2 3 4 1/2 100 200 450
2 1 1/2 3 4 3/4 130 270 650
3 1 1/2 3 6 1/4 190 380 800
4 1 1/2 4 6 1/2 340 660 1200
6 2 6 8 7/8 800 1400 2700
8 2 8 10 3/4 1100 2600 4200
10 2 1/2 8 13 1/2 1200 3300 5000

Figure P10L: Base Anchor – Low Profile

CUSHION
'C'
B.O.P.
T.O.S.
'W'
Finish: Notes:
See General Note 15, page 4. Lower saddle rests on supporting structure. Support
is provided with a base sized for a welded
Service: installation. A bolted installation is available upon
To support weight of pipe while restricting all request. Provide bolting arrangement with placement
movement of order. If limiting axial displacement is required,
request linestop clips type LS1 or LS2 with
Material: placement of order. Dimensions are based on typical
Carbon steel 150 PSI rated pipe and may vary depending on the
See General Note 14, page 3. actual O.D. and load requirements. See General
Notes, pages 3 and 4.

1 1 1/2 3 4 3/8 80 150 350
1 1/2 1 1/2 3 4 1/2 100 200 450
2 1 1/2 3 5 3/4 130 270 650
3 1 1/2 3 6 1/4 190 380 800
4 1 1/2 4 7 5/8 340 660 1200
6 2 6 10 5/8 800 1400 2700
8 2 8 11 3/4 1100 2600 4200
10 2 1/2 8 16 1/8 1200 3300 5000

Figure P13: Riser Guide
ELASTOMERIC 'W' FIELD SET GAP

CUSHION
'L2' A A
'L1'
6"
T.O.S.
1" FIELD
SET GAP
SECTION A-A
Finish: Notes:
Hot-dipped galvanized Not designed for vertical loads. Type RGC1 welded
See General Note 15, page 4. riser guide clips are provided with this style of
support. Type RGC2 bolted riser guide clips are
Service: available upon request, page 91. Dimensions are
To allow axial movement while limiting lateral based on typical 150 PSI rated pipe and may vary
movement depending on the actual O.D. and load
requirements. See page 51 for sizes 24” – 60”. See
Material: General Notes, page 3 and 4.
Carbon steel

[in] [in] [in] [in] Lateral
1 3 2 10 1/4 80
1 1/2 3 2 10 3/4 100
2 3 2 11 1/4 130
3 3 2 12 1/4 190
4 3 2 13 1/4 240
6 4 2 15 3/4 360
8 4 2 17 3/4 480
10 6 3 22 650
12 6 3 24 3/4 900
14 8 4 27 1500
16 8 4 29 1/2 1700
18 10 4 31 1/2 2300
20 10 4 34 2700

Figure P13: Riser Guide
ELASTOMERIC
CUSHION
A A
'L3'
FIELD SET GAP
'L1'
T.O.S.
'L2' 'W'
(TYP)
1" FIELD
SET GAP
SECTION A-A
Finish: Notes:
Painted Not designed for vertical loads. Type RGC1 welded
See General Note 15, page 4. riser clips are provided with this style support. Type
RGC2 bolted riser clips are available upon request,
Service: page 91. Dimensions are based on typical 150 PSI
To allow axial movement while limiting lateral rated pipe and may vary depending on the actual
movement O.D. and load requirements. See page 50 for sizes
1” – 20”. See General Notes, pages 3 and 4.
Material:
Carbon steel
Pipe Size L1 L2 L3 W Allowable Loads [lb]

[in] [in] [in] [in] [in] Lateral
24 8 4 6 38 6000
30 10 6 6 44 1/2 9100
36 12 6 8 54 1/2 13000
42 14 6 10 61 3/8 17000
48 16 6 10 67 7/8 23000
54 18 8 12 73 3/4 29000
60 20 8 12 80 35000

Figure P14: Riser Support
'W'
FRP SHEAR COLLAR
CUSHION
'L1'
T.O.S.
Finish: Notes:
Hot-dipped galvanized Not designed for lateral loading. Support width (W)
See General Note 15, page 4. is based on listed available loads. For a greater
width, the support configuration may need to be
Service: adjusted to suit listed available loads. If a fixed
To support weight of pipe while allowing anchor type support is required, provide loads for
freedom of lateral movement evaluation. Dimensions are based on typical 150
PSI rated pipe and may vary depending on the
Material: actual O.D. and load requirements. See page 53
Carbon steel for sizes 12” – 30”. See page 54 for sizes 36” –
See General Note 14, page 3. 60”. See General Notes, pages 3 and 4.
Pipe Size L1 W Allowable Loads [lb]

[in] [in] [in] Vertical
1 3 10 1/4 400
1 1/2 3 10 3/4 550
2 3 11 1/4 700
3 3 12 1/4 850
4 3 13 1/4 1200
6 4 15 3/4 1600
8 4 17 3/4 2000
10 6 20 3/4 2800

'W'
ELASTOMERIC FRP SHEAR COLLAR

CUSHION (NOT INCLUDED)
'L1'
'L2'
T.O.S.
Finish: Notes:
Hot-dipped galvanized Not designed for lateral loading. Support width (W) is
See General Note 15, page 4. based on listed available loads. For a greater width,
the support configuration may need to be adjusted to
Service: suit listed available loads. If a fixed anchor type
To support weight of pipe while allowing freedom support is required, provide loads for evaluation.
of lateral movement Dimensions are based on typical 150 PSI rated pipe
and may vary depending on the actual O.D. and load
Material: requirements. See page 52 for sizes 1” – 10”. See
Carbon steel page 54 for sizes 36” – 60”. See General Notes,
See General Note 14, page 3. pages 3 and 4.

12 6 5 1/2 24 3/4 3200
14 8 7 1/2 27 4000
16 9 8 1/2 29 1/2 4800
18 10 9 1/2 31 1/2 5900
20 12 11 34 7700
24 12 11 38 9500
30 12 11 44 1/2 13500

ELASTOMERIC
CUSHION
FRP SHEAR COLLAR

(NOT INCLUDED)
A A
'L2' 'L1'
SECTION A-A
'W'
(TYP)
Finish: Notes:
Painted Not designed for lateral loading. Support width (W) is
See General Note 15, page 4. based on listed available loads. For a greater width,
the support configuration may need to be adjusted to
Service: suit listed available loads. If a fixed anchor type
To support weight of pipe while allowing freedom support is required, provide loads for evaluation.
of lateral movement Dimensions are based on typical 150 PSI rated pipe
and may vary depending on the actual O.D. and load
Material: requirements. See page 52 for sizes 1” – 10”. See
Carbon steel page 53 for sizes 12” – 30”. See General Notes,
See General Note 14, page 3. pages 3 and 4.

36 12 11 53 13000 32000
42 14 13 60 17000 45000
48 16 15 66 1/2 23000 58000
54 18 17 73 3/4 29000 72000
60 20 19 80 35000 85000

Figure P15: Double Rod Riser Hanger
HANGING HARDWARE
(NOT INCLUDED) 'D'
FRP SHEAR COLLAR

(NOT INCLUDED)
ELASTOMERIC
CUSHION
'L2'
'L1'
PIN 'P'
(NOT INCLUDED)
'W'
Finish: Notes:
Hot-dipped galvanized Support width (W) is based on listed allowable loads.
See General Note 15, page 4. For a greater width, the support configuration may
need to be adjusted to suit listed allowable loads.
Service: Dimensions are based on typical 150 PSI rated pipe
To support weight of pipe from above while and may vary depending on the actual O.D. and load
allowing freedom of movement requirements. Hanging hardware is available upon
request. See page 56 for sizes 12” – 30”. See
Carbon steel
Pipe Size D L1 L2 P W Allowable Loads [lb]

1 3/8 3 1 1/2 1/2 9 1/2 400
1 1/2 3/8 3 1 1/2 1/2 10 550
2 3/8 3 1 1/2 1/2 10 1/2 700
3 1/2 3 1 1/2 5/8 11 1/2 850
4 5/8 3 1 1/2 3/4 12 1/2 1200
6 3/4 4 2 7/8 15 1600
8 3/4 4 2 7/8 17 2000
10 7/8 6 2 1 20 2800

Figure P15: Double Rod Riser Hanger
HANGING HARDWARE
(NOT INCLUDED) 'D'
FRP SHEAR COLLAR

(NOT INCLUDED)
ELASTOMERIC
CUSHION
'L2'
'L1'
PIN 'P'
(NOT INCLUDED)
'W'
Finish: Notes:
Service: Dimensions are based on typical 150 PSI rated pipe
To support weight of pipe from above while and may vary depending on the actual O.D. and load
allowing freedom of movement requirements. Hanging hardware is available upon
request. See page 55 for sizes 1” – 10”. See General
Material: Notes, pages 3 and 4.
Carbon steel
Pipe Size D L1 L2 P W Allowable Loads [lb]

12 7/8 6 2 1 22 3200
14 1 8 2 1/4 1 1/8 24 1/2 4000
16 1 9 2 1/4 1 1/8 26 3/4 4800
18 1 10 2 1/4 1 1/8 28 3/4 5900
20 1 1/4 12 3 1 3/8 32 1/2 7700
24 1 1/4 12 3 1 3/8 36 1/2 9500
30 1 1/2 12 3 1 5/8 43 13500

Figure P16: Riser Support W/ Guides
'W'
(TYP)
A A
FIELD SET GAP

'L1'
T.O.S.
6"
3"
SECTION A-A
Finish: Notes:
Service: Type RGC1 welded guide clips are provided with this
To support weight of pipe while limiting lateral style support. Type RGC2 bolted guide clips are
movement available upon request, page 91. Dimensions are
based on typical 150 PSI rated pipe and may vary
Material: depending on the actual O.D. and load requirements.
Carbon steel See page 58 for sizes 12” – 30”. See page 59 for
See General Note 14, page 3. sizes 36” – 60”. See General Notes, pages 3 and 4.

[in] [in] [in] Lateral Vertical
1 3 10 1/4 80 400
1 1/2 3 10 3/4 100 550
2 3 11 1/4 130 700
3 3 12 1/4 190 850
4 3 13 1/4 240 1200
6 4 15 3/4 360 1600
8 4 17 3/4 480 2000
10 6 20 3/4 650 2800

'W'
(TYP) FRP SHEAR COLLAR
(NOT INCLUDED)
A A
FIELD SET GAP

'L2' 'L1'
T.O.S.
6"
4"
SECTION A-A
Finish: Notes:
Carbon steel See page 57 for sizes 1” – 10”. See page 59 for sizes
See General Note 14, page 3. 36” – 60”. See General Notes, pages 3 and 4.
.

12 6 5 1/2 24 3/4 900 3200
14 8 7 1/2 27 1500 4000
16 9 8 1/2 29 1/2 1700 4800
18 10 9 1/2 31 1/2 2300 5900
20 12 11 34 2700 7700
24 12 11 38 3300 9500
30 12 11 44 1/2 4000 13500

A A
FRP SHEAR COLLAR
(NOT INCLUDED)
'L1' 'L2'
T.O.S.
'L3' 'W'
(TYP)
SECTION A-A
Finish: Notes:
Painted Support width (W) is based on listed allowable loads.
Carbon steel See page 57 for sizes 1” – 10”. See page 58 for sizes

36 12 11 6 53 13000 32000
42 14 13 6 60 17000 45000
48 16 15 6 66 1/2 23000 58000
54 18 18 8 73 3/4 29000 72000
60 20 19 8 80 35000 85000

Figure P17: Base Linestop

(NOT INCLUDED)
ELASTOMERIC
'C' CUSHION
B.O.P.
'H'
T.O.S.
PTFE SLIDE
BEARINGS
(2) PLACES
'W' 'L2'
Finish: Notes:
Hot-dipped galvanized Base width (W) and length (L2) must be fully
See General Note 15, page 4. supported as shown. If axial and lateral
displacements are to be limited, request optional
Service: base plate type BP4, page 89. Support is provided
To support weight of pipe while allowing freedom with a base plate for welded installations. Base
of lateral movement and limiting axial movement plates for bolted installations are available upon
Material: of order. Dimensions are based on typical 150 PSI
Carbon steel rated pipe and may vary depending on the actual
See General Note 14, page 3. O.D. and load requirements. PTFE slide bearings are
recommended for pipe sizes above 10” NPS. See
pages 3 and 4.
Pipe Size C H L1 L2 W Allowable Loads [lb]

[in] [in] [in] [in] [in] [in] Vertical Axial
12 2 1/2 3 8 15 1/2 16 3900 3500
14 2 1/2 3 10 17 1/2 18 5700 4000
16 2 1/2 3 12 19 1/2 20 7500 6000
18 3 3 14 21 1/2 21 3/4 10000 7000
20 3 3 1/4 14 21 1/2 24 11000 11000
24 3 3 1/4 18 25 1/2 27 3/8 16000 15000
30 3 4 20 30 32 3/4 18000 16000

Figure P17: Base Linestop

CUSHION
'C'
B.O.P.
8"
T.O.S.
'W' PTFE SLIDE 'L2'

BEARINGS
(2) PLACES
Finish: Notes:
Painted Base width (W) and length (L2) must be fully
See General Note 15, page 4. supported as shown. If lateral displacements are to
be limited, request optional base plate type BP4,
Service: page 89 and provide load requirements. Support is
To support weight of pipe while allowing freedom provided with a base plate for welded installations.
of lateral movement and limiting axial movement Base plates for bolted installations are available upon
Material: of order. Dimensions are based on typical 150 PSI
Carbon steel rated pipe and may vary depending on the actual
See General Note 14, page 3. O.D. and load requirements. PTFE slide bearings are
recommended for pipe sizes above 10” NPS. See
pages 3 and 4.
Pipe Size C L1 L2 W Allowable Loads [lb]

36 4 24 30 1/2 40 21000 18000
42 4 26 32 1/2 47 30000 24000
48 4 28 34 1/2 53 1/4 39000 30000
54 4 30 37 1/4 57 3/4 48000 36000
60 4 32 39 1/4 63 1/4 56000 40000

'L1'
'L2'
ELASTOMERIC
'C' CUSHION
B.O.P.
'H'
T.O.S.
PTFE SLIDE
BEARINGS
(2) PLACES
'W' 'L3'
Finish: Notes:
To support weight of pipe while allowing freedom typical 150 PSI rated pipe and may vary depending
of movement on the actual O.D. and load requirements. PTFE
Material: above 10” NPS. See page 63 for sizes 36” – 60”. See
Pipe Size C H L1 L2 L3 W Allowable Loads [lb]

[in] [in] [in] [in] [in] [in] [in] Vertical
12 2 1/2 3 6 4 6 16 3200
14 2 1/2 3 8 6 8 18 4950
16 2 1/2 3 8 6 8 20 5700
18 3 3 10 6 8 21 3/4 8000
20 3 3 1/4 10 6 8 24 8900
24 3 3 1/4 12 8 10 27 3/8 12600
30 3 4 15 10 12 32 3/4 15000

'L1'
ELASTOMERIC 'L2'
CUSHION
'C'
B.O.P.
8"
T.O.S.
'W' PTFE SLIDE 12"

BEARINGS
(2) PLACES
Finish: Notes:
To support weight of pipe while allowing freedom typical 150 PSI rated pipe and may vary depending
of movement on the actual O.D. and load requirements. PTFE

36 4 18 12 40 21000
42 4 21 14 47 30000
48 4 24 16 53 1/4 39000
54 4 27 18 57 3/4 48000
60 4 30 20 63 1/4 56000

'L1'
'L2'
ELASTOMERIC
'C' CUSHION
B.O.P.
'H'
T.O.S.
PTFE SLIDE
BEARINGS
(2) PLACES
'W' 'L3'
Finish: Notes:
To support weight of pipe while limiting lateral typical 150 PSI rated pipe and may vary depending
movement on the actual O.D. and load requirements. PTFE
Pipe Size C H L1 L2 L3 W Allowable Loads [lb]

[in] [in] [in] [in] [in] [in] [in] Lateral Vertical
12 2 1/2 3 6 4 6 19 3/4 900 3000
14 2 1/2 3 8 6 8 21 3/4 1500 4600
16 2 1/2 3 8 6 8 23 3/4 1700 5400
18 3 3 10 6 8 25 1/2 2300 7500
20 3 3 1/4 10 6 8 27 3/4 2700 8200
24 3 3 1/4 12 8 10 31 1/8 5200 11000
30 3 4 15 10 12 38 7500 15000

'L1'
ELASTOMERIC 'L2'
CUSHION
'C'
B.O.P.
8"
T.O.S.
'W' PTFE SLIDE 12"

BEARINGS
(2) PLACES
Finish: Notes:
To support weight of pipe while limiting lateral typical 150 PSI rated pipe and may vary depending
movement on the actual O.D. and load requirements. PTFE

36 4 18 12 47 14000 21000
42 4 21 14 53 1/2 19000 30000
48 4 24 16 60 25000 39000
54 4 27 18 66 31000 48000
60 4 30 20 71 1/2 37000 56000


(NOT INCLUDED)
'C'
ELASTOMERIC
CUSHION
B.O.P.
'H'
T.O.S.
'W'
Finish: Notes:
See General Note 15, page 4. Support is provided with a base plate for welded
installations. Base plates for bolted installations are
Service: available upon request. Provide bolting arrangement
To support weight of pipe while restricting all with placement of order. Dimensions are based on
movement typical 150 PSI rated pipe and may vary depending
on the actual O.D. and load requirements. See page
Material: 67 for sizes 36” – 60”. See General Notes, pages 3
Carbon steel and 4.
Pipe Size C H L1 W Allowable Loads [lb]

[in] [in] [in] [in] [in] Lateral Vertical Axial
12 2 1/2 3 8 16 1600 3900 3500
14 2 1/2 3 10 18 2300 5700 4000
16 2 1/2 3 12 20 3500 7500 6000
18 3 3 14 21 3/4 4500 10000 7000
20 3 3 1/4 14 24 5500 11000 11000
24 3 3 1/4 18 27 3/8 8000 16000 15000
30 3 4 20 32 3/4 9000 18000 16000

ELASTOMERIC 'L1'
CUSHION
'C'
B.O.P.
8"
T.O.S.
FRP SHEAR COLLARS

'W' (NOT INCLUDED)
Finish: Notes:
Painted Base width (W) must be fully supported as shown.
See General Note 15, page 4. Support is provided with a base plate for welded
installations. Base plates for bolted installations are
Service: available upon request. Provide bolting arrangement
To support weight of pipe while restricting all with placement of order. Dimensions are based on
movement typical 150 PSI rated pipe and may vary depending
on the actual O.D. and load requirements. See page
Material: 66 for sizes 12” – 30”. See General Notes, pages 3
Carbon steel and 4.

36 4 24 40 10000 21000 21000
42 4 26 47 15000 30000 30000
48 4 28 53 1/4 19000 39000 39000
54 4 30 57 3/4 24000 48000 45000
60 4 32 63 1/4 32000 56000 50000

Figure XL12: Extra Large Slide
(66” – 108” Diameter)
'L1'
ELASTOMERIC
CUSHION
4"
B.O.P.
8" T.O.S.
PTFE SLIDE
BEARINGS
'W' 12"
Finish: Notes:
Painted Large diameter pipe supports are engineered to suit
See General Note 15, page 4. project requirements. Contact us for further
information and how to order. Base width (W) must
Service: be fully supported as shown. Support is provided with
To support weight of pipe or duct while allowing a base plate for welded installations. Base plates for
freedom of movement bolted installations are available upon request.
Provide bolting arrangement with placement of order.
Material: PTFE slide bearings are recommended. Where
Carbon steel increase friction is desirable, the base plate and
See General Note 14, page 3. bearing(s) may be eliminated. Dimensions may vary
depending on actual pipe O.D. and load
requirements. See General Notes, pages 3 and 4.
Pipe Size L1 W
[in] [in] [in]
66 33 74
72 36 80
78 39 90
84 42 92
90 45 98
96 48 104
102 48 110
108 48 116

Figure XL13: Extra Large Guide
(66” – 108” Diameter)
'L1'
ELASTOMERIC
CUSHION
4"
B.O.P.
8" T.O.S.
PTFE SLIDE
BEARINGS
'W' 12"
Finish: Notes:
To support weight of pipe or duct while allowing a base plate for welded installations. Base plates for
freedom of axial movement and limiting lateral bolted installations are available upon request.
movement Provide bolting arrangement with placement of order.
PTFE slide bearings are recommended. Where
Material: increase friction is desirable, the base plate and
Carbon steel bearing(s) may be eliminated. Dimensions may vary
See General Note 14, page 3. depending on actual pipe O.D. and load
requirements. See General Notes, pages 3 and 4.
Pipe Size L1 W
[in] [in] [in]
66 33 80
72 36 86
78 39 96
84 42 98
90 45 104
96 48 110
102 48 116
108 48 122

Figure XL14: Extra Large Anchor
(66” – 108” Diameter)
ELASTOMERIC 'L1'
CUSHION
4"
B.O.P.
8" T.O.S.
'W' FRP SHEAR COLLARS

(NOT INCLUDED)
Finish: Notes:
To support weight of pipe or duct while restricting a base plate for welded installations. Base plates for
all movement bolted installations are available upon request.
Provide bolting arrangement with placement of order.
Material: Dimensions may vary depending on actual pipe O.D.
Carbon steel and load requirements. See General Notes, pages 3
See General Note 14, page 3. and 4.
Pipe Size L1 W
[in] [in] [in]
66 33 74
72 36 80
78 39 90
84 42 92
90 45 98
96 48 104
102 48 110
108 48 116

Duct Supports

Figure D1: Duct Clamp Hanger
HANGING HARDWARE
'D' (NOT INCLUDED)
PIN 'P'
(NOT INCLUDED)
ELASTOMERIC
CUSHION
'H'
'C'
'L1'
Finish: Notes:
20” – 30”: Hot-dipped galvanized Dimensions may vary depending on the actual O.D.
36” – 60”: Painted and load requirements. Hanging hardware is
See General Note 15, page 4. available upon request. See General Notes, pages
3 and 4.
Service:
To support weight of duct from above while
Material:
Carbon steel

20 2 1/2 1/2 15 3/4 6 5/8 900
24 2 1/2 1/2 18 3/16 6 5/8 1200
30 2 1/2 5/8 22 8 3/4 1750
36 2 1/2 3/4 26 10 7/8 2400
42 3 7/8 30 3/8 10 1 3750
48 3 1 35 1/4 12 1 1/8 4750
54 3 1 1/4 37 3/16 16 1 3/8 6000
60 3 1 1/4 40 1/4 16 1 3/8 7500

Figure D3: Duct Cradle Base Slide
BANDING 'L1'
(SEE NOTES)
ELASTOMERIC
CUSHION
B.O.P.
'H'
T.O.S.
'W' 'L2'
Finish: Notes:
20” – 30”: Hot-dipped galvanized Not designed for lateral or axial loads. Base width
36” – 60”: Painted (W) must be fully supported as shown. Dimensions
See General Note 15, page 4. may vary depending on the actual O.D. and load
requirements. Banding can be provided in bulk upon
Service: request. See General Notes, pages 3 and 4.
To support weight of duct while allowing freedom
of movement
Material:
Carbon steel

20 7 10 6 21 450
24 7 10 6 25 600
30 8 10 6 30 875
36 8 10 6 36 1200
42 8 12 8 42 1875
48 8 12 8 48 2375
54 8 16 12 54 3000
60 8 16 12 60 3750

Figure D4: Duct Base Linestop
'L1'
'C'
ELASTOMERIC
CUSHION
B.O.P.
8"
T.O.S. FRP SHEAR COLLARS
(NOT INCLUDED)
'W' PTFE SLIDE 'L2'

BEARINGS
(2) PLACES
Finish: Notes:
20” – 30”: Hot-dipped galvanized Base width (W) and length (L2) must be fully
36”: Painted supported as shown. If lateral displacements are to
See General Note 15, page 4. be limited, request optional base plate type BP4,
page 89 and provide loads for evaluation. Support is
Service: provided with a base plate for welded installation.
To support weight of duct while allowing freedom Base plates for bolted installations are available upon
of lateral movement and limiting axial movement request. Provide bolting arrangement with placement
of order. Dimensions may vary depending on the
Material: actual O.D. and load requirements. PTFE slide
Carbon steel bearings are recommended. See page 75 for sizes

20 2 1/2 8 15 1/2 24 900 1800
24 2 1/2 8 15 1/2 27 3/8 1200 2100
30 2 1/2 10 20 31 3/4 1750 3000
36 2 1/2 12 22 36 2400 4200

Figure D4: Duct Base Linestop
'L1'
'C'
ELASTOMERIC
CUSHION
B.O.P.
8"
(NOT INCLUDED)
PTFE SLIDE
'W' BEARINGS
(2) PLACES 'L2'
Finish: Notes:
See General Note 15, page 4. supported as shown. If lateral displacements are to
be limited, request optional base plate type BP4,
Service: page 89 and provide loads for evaluation. Support is
To support weight of duct while allowing freedom provided with a base plate for welded installation.
of lateral movement and limiting axial movement Base plates for bolted installations are available upon
Material: of order. Dimensions may vary depending on the
Carbon steel actual O.D. and load requirements. PTFE slide
See General Note 14, page 3. bearings are recommended. See page 74 for sizes
20” – 36”. See General Notes, pages 3 and 4.

42 3 14 24 1/2 43 3750 6000
48 3 16 26 1/2 49 1/4 4750 7500
54 3 18 29 1/4 53 3/4 6000 9000
60 3 20 31 1/4 59 1/4 7500 12000

Figure D5: Duct Base Slide
'L1'
'C'
ELASTOMERIC
CUSHION
B.O.P.
8"
T.O.S.
PTFE SLIDE
BEARINGS
(2) PLACES 'L2'
'W'
Finish: Notes:
36”: Painted installation. Base plates for bolted installations are
with placement of order. Dimensions may vary
Service: depending on the actual O.D. and load requirements.
To support weight of duct while allowing freedom PTFE slide bearings are recommended. See page 77
of movement for sizes 42” – 60”. See General Notes, pages 3 and
4.
Material:
Carbon steel

20 2 1/2 6 6 24 900
24 2 1/2 6 6 27 3/4 1200
30 2 1/2 8 6 31 3/4 1750
36 2 1/2 10 8 36 2400

Figure D5: Duct Base Slide
'L1'
'C'
ELASTOMERIC
CUSHION
B.O.P.
8"
T.O.S.
PTFE SLIDE
BEARINGS
(2) PLACES 'L2'
'W'
Finish: Notes:
See General Note 15, page 4. installation. Base plates for bolted installations are
Service: with placement of order. Dimensions may vary
To support weight of duct while allowing freedom depending on the actual O.D. and load requirements.
of movement PTFE slide bearings are recommended. See page 76
for sizes 20” – 36”. See General Notes, pages 3 and
Material: 4.
Carbon steel

42 3 10 8 43 3750
48 3 12 10 49 1/4 4750
54 3 16 12 53 3/4 6000
60 3 16 12 59 1/4 7500

Figure D6: Duct Base Guide
'L1'
'C'
ELASTOMERIC
CUSHION
B.O.P.
8"
T.O.S.
PTFE SLIDE
BEARINGS 'L2'
'W' (2) PLACES
Finish: Notes:
36”: Painted installation. Base plates for bolted installations are
with placement of order. Dimensions may vary
Service: depending on the actual O.D. and load requirements.
To support weight of duct while allowing freedom PTFE slide bearings are recommended. See page 79
of axial movement and limiting lateral movement for sizes 42” – 60”. See General Notes, pages 3 and
4.
Material:
Carbon steel

20 2 1/2 6 6 28 1800 900
24 2 1/2 6 6 33 2100 1200
30 2 1/2 8 6 38 3000 1750
36 2 1/2 10 8 43 4200 2400

Figure D6: Duct Base Guide
'L1'
'C'
ELASTOMERIC
CUSHION
B.O.P.
8"
T.O.S.
PTFE SLIDE
BEARINGS 'L2'
'W' (2) PLACES
Finish: Notes:
See General Note 15, page 4. installation. Base plates for bolted installations are
Service: with placement of order. Dimensions may vary
To support weight of duct while allowing freedom depending on the actual O.D. and load requirements.
of axial movement and limiting lateral movement PTFE slide bearings are recommended. See page 78
for sizes 20” – 36”. See General Notes, pages 3 and
Material: 4.
Carbon steel

42 3 10 8 49 1/2 6000 3750
48 3 12 10 56 7500 4750
54 3 16 12 62 9000 6000
60 3 16 12 67 1/2 12000 7500

Figure D7: Duct Base Anchor
'L1'
'C'
ELASTOMERIC
CUSHION
B.O.P.
8"
(NOT INCLUDED)
'W'
Finish: Notes:
20” – 30”: Hot-dipped galvanized Base width (W) and length (L1) must be fully
36”: Painted supported as shown. Support is provided with a base
See General Note 15, page 4. plate for welded installation. Base plates for bolted
installations are available upon request. Provide
Service: bolting arrangement with placement of order.
To support weight of duct while restricting all Dimensions may vary depending on the actual O.D.
movement and load requirements. See page 81 for sizes 42” –
60”. See General Notes, pages 3 and 4.
Material:
Carbon steel

20 2 1/2 8 24 1800 900 1800
24 2 1/2 8 27 3/8 2100 1200 2100
30 2 1/2 10 31 3/4 3000 1750 3000
36 2 1/2 12 36 4200 2400 4200

Figure D7: Duct Base Anchor
'L1'
'C'
ELASTOMERIC
CUSHION
B.O.P.
8"
(NOT INCLUDED)
'W'
Finish: Notes:
See General Note 15, page 4. supported as shown. Support is provided with a base
plate for welded installation. Base plates for bolted
Service: installations are available upon request. Provide
To support weight of duct while restricting all bolting arrangement with placement of order.
movement Dimensions may vary depending on the actual O.D.
and load requirements. See page 80 for sizes 20” –
Material: 36”. See General Notes, pages 3 and 4.
Carbon steel

42 3 14 43 6000 3750 6000
48 3 16 49 1/4 7500 4750 7500
54 3 18 53 3/4 9000 6000 9000
60 3 20 59 1/4 12000 7500 12000

Figure D16: Duct Riser Guide
ELASTOMERIC 'W' FIELD SET GAP

CUSHION
'L2' A A
'L1'
4"
T.O.S.
1" FIELD
SET GAP
SECTION A-A
Finish: Notes:
Hot-dipped galvanized Not designed for vertical loads. Type RGC1 welded
See General Note 15, page 4. riser guide clips are provided with this style of
support. Type RGC2 bolted riser guide clips are
Service: available upon request, page 91. Dimensions may
To allow axial movement while limiting lateral vary depending on the actual O.D. and load
movement requirements. See page 3 for sizes 36” – 60”. See
General Notes, page 3 and 4.
Material:
Carbon steel

[in] [in] [in] [in] Lateral
20 6 4 34 1800
24 6 4 38 2100
30 8 4 44 1/2 3000

Figure D16: Duct Riser Guide
ELASTOMERIC
CUSHION
A A
'L3'
FIELD SET GAP
'L1'
T.O.S.
'L2' 'W'
(TYP)
1" FIELD
SET GAP
SECTION A-A
Finish: Notes:
Painted Not designed for vertical loads. Support width (W) is
See General Note 15, page 4. based on listed allowable loads. For a greater width,
the support configuration may need to be adjusted
Service: to suit listed allowable loads. Type RGC1 welded
To allow axial movement while limiting lateral guide clips are provided with this style support.
movement Type RGC2 bolted riser guide clips are available
upon request, page 91. Dimensions may vary
Material: depending on the actual duct O.D. and load
Carbon steel requirements. See page 82 for sizes 20” – 30”. See
See General Note 14, page 3. General Notes, pages 3 and 4.

[in] [in] [in] [in] [in] Lateral
36 10 4 8 48 4200
42 10 4 10 56 6000
48 12 6 10 64 7500
54 16 6 12 70 9000
60 16 6 12 72 12000

Figure D17: Duct Riser Support W/ Guides
'W'
(TYP)
A A
FIELD SET GAP

'L1'
T.O.S.
6"
3"
SECTION A-A
Finish: Notes:
Hot-dipped galvanized Support width (W) is based on listed allowable
See General Note 15, page 4. loads. For a greater width, the support configuration
may need to be adjusted to suit listed allowable
Service: loads. Type RGC1 welded guide clips are provided
To support weight of pipe or duct while limiting with this style support. Type RGC2 bolted guide
lateral movement clips are available upon request, page 91.
Dimensions may vary depending on the actual O.D.
Material: and load requirements. See page 85 for sizes 36” –
Carbon steel 60”. See General Notes, pages 3 and 4.

[in] [in] [in] Lateral Vertical
20 8 34 1800 900
24 8 38 2100 1200
30 10 44 1/2 3000 1750

Figure D17: Duct Riser Support W/ Guides
ELASTOMERIC
CUSHION
A A
'L3'
FIELD SET GAP
'L1'
T.O.S.
'L2' 'W'
(TYP)
1" FIELD
SET GAP
SECTION A-A
Finish: Notes:
Painted Support width (W) is based on listed allowable loads.
Service: Type RCG1 welded riser guide clips are provided
To support weight of duct while limiting lateral with this style support. Type RCG2 bolted riser guide
movement clips are available upon request, page 91.
Dimensions may vary depending on the actual duct
Material: O.D. and load requirements. See page 84 for sizes
Carbon steel 20” – 30”. See General Notes, pages 3 and 4.

36 12 4 8 48 4200 2400
42 14 4 10 56 6000 3750
48 16 6 10 64 7500 4750
54 18 6 12 70 9000 6000
60 20 6 12 72 12000 7500

Support Options

Figure O1: Variable Spring Hanger Supports
Variable spring hanger supports are used at locations that are subjected to vertical thermal
displacements. The size and type of variable spring hangers to be used depends on the load
requirements and the method of installation. The actual load for which the spring is to support (hot
condition), and the amount and direction of the pipe line movement from the cold to the hot position is
required to properly determine sizes.
BASE MOUNTED DOUBLE CAN
This illustration above depicts a large diameter base mount type support with slide bearings and variable
spring hangers. Other configurations are available such as single and / or double rod type suspended
from above.

Figure O2: Slide Bearings
Slide bearings minimize the frictional resistance of pipe supports as much as 40% thus reducing the
chance of the pipe supports binding and creating localized stresses in the pipe. Slide bearings also
reduce the loads transferred to a supporting structure. As pipe sizes and dead weights increase, slide
bearings become more critical with the increased frictional loads. Slide bearings are recommended for all
pipe sizes 12” diameter and above and systems having large temperature gradients and displacements.
UPPER SUPPORT BEARING BACKING PLATE

BASE PLATE
UPPER PTFE BEARING

LOWER PTFE BEARING
LOWER SUPPORT BEARING BACKING PLATE

BASE PLATE
PTFE slide bearings are bonded to steel backing plates, which are then welded to upper and lower
support base plates. For pipe supports without a lower base plate, the lower bearing can be welded
directly to the supporting structure.

Figure O3: Base Plates
If base plates are desired to accompany pipe supports, base plates may be supplied as part of a total
assembly. Base plates are available in standard dimensions or to customer specifications. The standard
base plate provided with our base mounted supports is for welded installations. All base mounted
supports with slide bearings are provided with both an upper and a lower base plate that includes the
slide bearing assemblies. Base plates can be provided for bolted installations upon request. Please
provide bolting configuration requirements with placement of order.
BP1 BP2
Slide Baseplate Guide Baseplate
(See Note)
BP3 BP4
Linestop Baseplate Linestop Baseplate W/
(See Note) Lateral Limits
(See Note)
Note:
The type of guide and linestop clips depends on the style of the support and may vary from what is
indicated here.

Figure O4: Guide Clips
Guide clips are used to direct and control pipe displacements.
Type FB1 is designed to limit horizontal (lateral or axial depending on placement) and vertical
displacements. It is provided with our standard supports without slide bearings or lower base plates. It is
designed for field welded installations.
Type FB2 is designed to limit horizontal (lateral or axial depending on placement) and vertical
displacements. It is for use with our standard supports without slide bearings and lower base plates. It is
designed for bolted and welded installations and can be provided upon request.
TYPE FB1 TYPE FB2
Types GC1 is designed to limit horizontal (lateral or axial depending on placement) and vertical
displacements. It is provided with our standard supports with slide bearings and is factory welded to the
lower base plate. Upon request, it can be provided loose for field installation. The standard lower base
plate can also be re-sized to allow for installation direct to the supporting structure.
Type GC2 is designed to limit only lateral and axial displacements and can be used with or without slide
bearing or lower base plates. It allows for either field welded or bolted installations.
TYPE GC1 TYPE GC2

Figure O4: Guide Clips
Type RGC1 is designed to limit horizontal displacements of riser piping. It is provided with our riser
supports and is shipped loose for field welded installations.
Type RGC2 is designed to limit horizontal displacements of riser piping. It is designed for bolted
installations and can be provided in lieu of the standard Type RGC1 upon request.
TYPE RGC1 TYPE RGC2

Figure O5: Expansion Joint W/ Control Rods
The purpose of an expansion joint is to absorb the expansion and contraction of a pipeline between two
anchoring points. A Control Unit Assembly is a system of tie rods placed across an expansion joint to
minimize expansion and contraction thereby eliminating possible damage to the expansion joint. Control
Unit Assemblies are also used when it is not feasible in the supporting structure to provide an anchoring
system to control the expansion and contraction of the piping system.
An expansion joint Control Unit Assembly for an FRP piping system usually consists of sectional backing
plates (360° coverage) to distribute the imposed loads around the pipe flanges, tie-rod lugs, tie-rods and
compression sleeves. The number of tie-rods used in an assembly is determined on the basis of the
actual design/test pressure of the system. Pipe flange strength must be considered to insure they are
sufficient to withstand the total force that will be imposed.
STEEL BACKING RING EXPANSION JOINT

360 DEG, BOTH SIDES
TIE-ROD LUG TIE-ROD W/

COMPRESSION
SLEEVE

Technical Data

FRP Pipe & Fluid Weight Per Foot
The table below contains estimated weights of typical FRP piping and contents per lineal foot. Estimated
total weights are provided for various values of specific gravity (S.G.) of contents. Since FRP properties
and dimensions can vary significantly, this information should only be used for preliminary estimates.
It is the piping design engineer’s responsibility to confirm all spans.
Pipe Size Weight Of Empty Weight Of Water In Total Weight Per Ft (lb/ft)
[in] Pipe Per Ft (lb/ft) Pipe Per Ft (lb/ft) S.G. = 1 S.G. = 1.15 S.G. = 1.35
2 1.7 1.4 3.1 3.3 3.5
3 2.4 3.1 5.5 6.0 6.6
4 3.6 5.5 9.0 9.8 10.9
6 5.8 12.3 18.0 19.8 22.3
8 8.3 21.8 30.1 33.3 37.7
10 12.1 34.0 46.1 51.2 58.0
12 15.4 49.0 64.4 71.8 81.6
14 25.4 66.7 92.1 102 115
16 31.7 87.1 119 132 149
18 37.1 110 147 164 186
20 42.8 136 179 199 227
24 57.4 196 253 283 322
30 81.8 306 388 434 495
36 110 441 551 617 706
42 139 600 739 829 949
48 175 784 959 1077 1234
54 210 992 1203 1352 1550
60 243 1225 1469 1652 1897

Support Spans For 50 PSI FRP Pipe
The table below contains estimated maximum spans for typical 50 PSI rated FRP pipe. See page 96
for estimated spans for 150 PSI rated FRP pipe. Estimated maximum spans are provided for various
values of specific gravity (S.G.) of contents. These spans are calculated based on typical deflection
and stress criteria for FRP piping. Since FRP properties and dimensions can vary significantly, this
information should only be used for preliminary estimates.
'L' 'L' 'L'
Simple Span 'L' (ft) Continuous Span 'L' (ft) Cantilever Span 'L' (ft)
PipeSize
S.G. = S.G. = S.G. = S.G. = S.G. = S.G. =
[in] S.G. = 1 S.G. = 1 S.G. = 1
1.15 1.35 1.15 1.35 1.15 1.35
2 7.2 7.1 6.9 8.4 8.3 8.1 4.1 4.0 3.9
3 8.1 7.9 7.7 9.5 9.3 9.1 4.6 4.5 4.4
4 8.7 8.5 8.3 10.2 10.0 9.7 5.0 4.8 4.7
6 9.8 9.5 9.2 11.4 11.2 10.8 5.5 5.4 5.3
8 10.5 10.3 10.0 12.4 12.0 11.7 6.0 5.8 5.7
10 11.1 10.8 10.5 13.1 12.7 12.3 6.3 6.2 6.0
12 11.7 11.4 11.0 13.7 13.3 12.9 6.6 6.5 6.1
14 12.9 12.6 12.2 15.1 14.7 14.3 7.3 7.1 6.9
16 13.3 13.0 12.6 15.6 15.2 14.8 7.6 7.3 6.9
18 13.8 13.4 13.0 16.2 15.7 15.2 7.8 7.4 6.9
20 14.2 13.8 13.4 16.6 16.2 15.6 7.9 7.4 7.0
24 14.9 14.5 14.0 17.4 16.7 15.7 7.9 7.5 7.0
30 16.7 16.2 15.7 19.6 18.8 17.6 8.9 8.4 7.9
36 17.5 16.9 15.8 20.0 18.9 17.7 9.0 8.5 7.9
42 18.0 17.0 15.9 20.2 19.0 17.8 9.0 8.5 8.0
48 19.8 18.7 17.5 22.1 20.9 19.5 9.9 9.3 8.7
54 21.2 20.3 18.9 24.0 22.6 21.1 10.7 10.1 9.5
60 21.6 20.3 19.0 24.1 22.7 21.2 10.8 10.2 9.5

Support Spans For 150 PSI FRP Pipe
The table below contains estimated maximum spans for typical 150 PSI rated FRP pipe. See page 95 for
estimated spans for 50 PSI rated FRP pipe. Estimated maximum spans are provided for various values of
specific gravity (S.G.) of contents. These spans are calculated based on typical deflection and stress
criteria for FRP piping. Since FRP properties and dimensions can vary significantly, this information
should only be used for preliminary estimates.
'L' 'L' 'L'
Simple Span 'L' (ft) Continuous Span 'L' (ft) Cantilever Span 'L' (ft)
PipeSize
S.G. = S.G. = S.G. = S.G. = S.G. = S.G. =
[in] S.G. = 1 S.G. = 1 S.G. = 1
1.15 1.35 1.15 1.35 1.15 1.35
2 7.2 7.1 6.9 8.4 8.3 8.1 4.1 4.0 3.9
3 8.1 7.9 7.7 9.5 9.3 9.1 4.6 4.5 4.4
4 8.7 8.5 8.3 10.2 10.0 9.7 5.0 4.8 4.7
6 9.8 9.5 9.2 11.4 11.2 10.8 5.5 5.4 5.3
8 10.5 10.3 10.0 12.4 12.0 11.7 6.0 5.8 5.7
10 12.0 11.7 11.3 14.1 13.7 13.3 6.8 6.6 6.4
12 13.4 13.0 12.6 15.6 15.2 14.8 7.6 7.4 7.2
14 13.7 13.3 12.9 16.0 15.6 15.1 7.8 7.6 7.3
16 14.8 14.4 14.0 17.4 16.9 16.4 8.4 8.2 8.0
18 15.9 15.5 15.0 18.7 18.2 17.6 9.1 8.8 8.5
20 16.4 16.0 15.5 19.2 18.7 18.1 9.3 9.1 8.8
24 18.3 17.8 17.3 21.5 20.9 20.2 10.4 10.1 9.8
30 19.5 18.9 18.2 22.8 22.1 21.5 11.0 10.7 10.4
36 20.2 19.6 18.9 23.6 23.0 22.2 11.4 11.2 10.8
42 20.6 20.0 19.3 24.1 23.4 22.6 11.6 11.3 11.0
48 21.2 20.6 19.8 24.8 24.1 23.3 12.1 11.7 11.3
54 21.4 20.7 20.0 25.0 24.3 23.5 12.2 11.8 11.4
60 21.7 21.1 20.3 25.4 24.7 23.9 12.3 11.9 11.6

FRP Pipe Thermal Expansion
The table below contains estimated thermal expansion and contraction for typical FRP Pipe. Estimated
changes in lengths (per 100ft of pipe) are provided for various temperatures based on a 70 deg F
installation temperature. Since FRP properties and dimensions can vary significantly, this information
Length Change per

Temperature
100ft (in/100ft)
0°F -1.26*
10°F -1.08*
20°F -0.90*
30°F -0.72*
40°F -0.54*
50°F -0.36*
60°F -0.18*
70°F 0.00
80°F 0.18
90°F 0.36
100°F 0.54
110°F 0.72
120°F 0.90
130°F 1.08
140°F 1.26
150°F 1.44
160°F 1.62
*Negative length change denotes contraction of pipe

Minimum Distance To Elbow For FRP Pipe
The table below contains estimated minimum distances from elbows to the nearest guide or anchor
support for typical FRP pipe. Since FRP properties and dimensions can vary significantly, this information
‚
' L'
'D'
Minimum Guide / Anchor Distance to Elbow, 'D' (ft)

PipeSize Change in Length, '∆ L' (in)
[in] 1/4 1/2 3/4 1 1 1/4 1 1/2 1 3/4 2 2 1/4 2 1/2 2 3/4 3
2 2.2 3.1 3.8 4.4 4.9 5.4 5.8 6.2 6.6 6.9 7.3 7.6
3 2.6 3.7 4.5 5.2 5.8 6.4 6.9 7.3 7.8 8.2 8.6 9.0
4 3.0 4.2 5.1 5.9 6.6 7.2 7.8 8.3 8.8 9.3 9.8 10.2
6 3.6 5.0 6.2 7.1 7.9 8.7 9.4 10.0 10.6 11.2 11.8 12.3
8 4.1 5.8 7.0 8.1 9.1 10.0 10.8 11.5 12.2 12.8 13.5 14.1
10 4.5 6.4 7.8 9.0 10.1 11.1 12.0 12.8 13.6 14.3 15.0 15.7
12 4.9 7.0 8.5 9.9 11.0 12.1 13.1 14.0 14.8 15.6 16.4 17.1
14 5.3 7.5 9.2 10.7 11.9 13.1 14.1 15.1 16.0 16.9 17.7 18.5
16 5.7 8.0 9.8 11.4 12.7 13.9 15.0 16.1 17.1 18.0 18.8 19.7
18 6.0 8.5 10.4 12.0 13.5 14.7 15.9 17.0 18.1 19.0 20.0 20.8
20 6.3 9.0 11.0 12.7 14.2 15.5 16.8 17.9 19.0 20.0 21.0 21.9
24 6.9 9.8 12.0 13.9 15.5 17.0 18.3 19.6 20.8 21.9 23.0 24.0
30 7.7 10.9 13.4 15.5 17.3 18.9 20.5 21.9 23.2 24.5 25.7 26.8
36 8.5 12.0 14.7 16.9 18.9 20.7 22.4 23.9 25.4 26.7 28.1 29.3
42 9.3 13.2 16.2 18.7 20.9 22.9 24.7 26.4 28.0 29.5 31.0 32.3
48 9.8 13.8 16.9 19.5 21.8 23.9 25.8 27.6 29.3 30.8 32.3 33.8
54 10.4 14.6 17.9 20.7 23.1 25.3 27.4 29.3 31.0 32.7 34.3 35.8

Fractions / Decimal / MM Conversions
FRACTION / DECIMAL / MM CONVERSIONS

Inches Metric Inches Metric Inches Metric
Fractional Decimal mm Fractional Decimal mm Fractional Decimal mm
. 0.0039 0.1000 . 0.1969 5.0000 . 0.5512 14.0000
. 0.0079 0.2000 13/64 0.2031 5.1594 9/16 0.5625 14.2875
. 0.0118 0.3000 . 0.2165 5.5000 . 0.5709 14.5000
1/64 0.0156 0.3969 7/32 0.2188 5.5563 37/64 0.5781 14.6844
. 0.0157 0.4000 15/64 0.2344 5.9531 . 0.5906 15.0000
. 0.0197 0.5000 . 0.2362 6.0000 19/32 0.5938 15.0813
. 0.0236 0.6000 1/4 0.2500 6.3500 39/64 0.6094 15.4781
. 0.0276 0.7000 . 0.2559 6.5000 . 0.6102 15.5000
1/32 0.0313 0.7938 17/64 0.2656 6.7469 5/8 0.6250 15.8750
. 0.0315 0.8000 . 0.2756 7.0000 . 0.6299 16.0000
. 0.0354 0.9000 9/32 0.2813 7.1438 41/64 0.6406 16.2719
. 0.0394 1.0000 . 0.2953 7.5000 . 0.6496 16.5000
. 0.0433 1.1000 19/64 0.2969 7.5406 21/32 0.6563 16.6688
3/64 0.0469 1.1906 5/16 0.3125 7.9375 . 0.6693 17.0000
. 0.0472 1.2000 . 0.3150 8.0000 43/64 0.6719 17.0656
. 0.0512 1.3000 21/64 0.3281 8.3344 11/16 0.6875 17.4625
. 0.0551 1.4000 . 0.3346 8.5000 . 0.6890 17.5000
. 0.0591 1.5000 11/32 0.3438 8.7313 45/64 0.7031 17.8594
1/16 0.0625 1.5875 . 0.3543 9.0000 . 0.7087 18.0000
. 0.0630 1.6000 23/64 0.3594 9.1281 23/32 0.7188 18.2563
. 0.0669 1.7000 . 0.3740 9.5000 . 0.7283 18.5000
. 0.0709 1.8000 3/8 0.3750 9.5250 47/64 0.7344 18.6531
. 0.0748 1.9000 25/64 0.3906 9.9219 . 0.7480 19.0000
5/64 0.0781 1.9844 . 0.3937 10.0000 3/4 0.7500 19.0500
. 0.0787 2.0000 13/32 0.4063 10.3188 49/64 0.7656 19.4469
. 0.0827 2.1000 . 0.4134 10.5000 . 0.7677 19.5000
. 0.0866 2.2000 27/64 0.4219 10.7156 25/32 0.7813 19.8438
. 0.0906 2.3000 . 0.4331 11.0000 . 0.7874 20.0000
3/32 0.0938 2.3813 7/16 0.4375 11.1125 51/64 0.7969 20.2406
. 0.0945 2.4000 . 0.4528 11.5000 . 0.8071 20.5000
. 0.0984 2.5000 29/64 0.4531 11.5094 13/16 0.8125 20.6375
7/64 0.1094 2.7781 15/32 0.4688 11.9063 . 0.8268 21.0000
. 0.1181 3.0000 . 0.4724 12.0000 53/64 0.8281 21.0344
1/8 0.1250 3.1750 31/64 0.4844 12.3031 27/32 0.8438 21.4313
. 0.1378 3.5000 . 0.4921 12.5000 . 0.8465 21.5000
9/64 0.1406 3.5719 1/2 0.5000 12.7000 55/64 0.8594 21.8281
5/32 0.1563 3.9688 . 0.5118 13.0000 . 0.8661 22.0000
. 0.1575 4.0000 33/64 0.5156 13.0969 7/8 0.8750 22.2250
11/64 0.1719 4.3656 17/32 0.5313 13.4938 . 0.8858 22.5000
. 0.1772 4.5000 . 0.5315 13.5000 57/64 0.8906 22.6219
3/16 0.1875 4.7625 35/64 0.5469 13.8906 . 0.9055 23.0000

Fractions / Decimal / MM Conversions
FRACTION / DECIMAL / MM CONVERSIONS

Inches Metric Inches Metric Inches Metric
Fractional Decimal mm Fractional Decimal mm Fractional Decimal mm
29/32 0.9063 23.0188 . 1.8898 48.0000 . 3.3071 84.0000
59/64 0.9219 23.4156 . 1.9291 49.0000 . 3.3465 85.0000
. 0.9252 23.5000 . 1.9685 50.0000 . 3.3858 86.0000
15/16 0.9375 23.8125 2 2.0000 50.8000 . 3.4252 87.0000
. 0.9449 24.0000 . 2.0079 51.0000 . 3.4646 88.0000
61/64 0.9531 24.2094 . 2.0472 52.0000 3 1/2 3.5000 88.9000
. 0.9646 24.5000 . 2.0866 53.0000 . 3.5039 89.0000
31/32 0.9688 24.6063 . 2.1260 54.0000 . 3.5433 90.0000
. 0.9843 25.0000 . 2.1654 55.0000 . 3.5827 91.0000
63/64 0.9844 25.0031 . 2.2047 56.0000 . 3.6220 92.0000
1 1.0000 25.4000 . 2.2441 57.0000 . 3.6614 93.0000
. 1.0039 25.5000 2 1/4 2.2500 57.1500 . 3.7008 94.0000
. 1.0236 26.0000 . 2.2835 58.0000 . 3.7402 95.0000
. 1.0433 26.5000 . 2.3228 59.0000 . 3.7795 96.0000
. 1.0630 27.0000 . 2.3622 60.0000 . 3.8189 97.0000
. 1.0827 27.5000 . 2.4016 61.0000 . 3.8583 98.0000
. 1.1024 28.0000 . 2.4409 62.0000 . 3.8976 99.0000
. 1.1220 28.5000 . 2.4803 63.0000 . 3.9370 100.0000
. 1.1417 29.0000 2 1/2 2.5000 63.5000 4 4.0000 101.6000
. 1.1614 29.5000 . 2.5197 64.0000 . 4.3307 110.0000
. 1.1811 30.0000 . 2.5591 65.0000 4 1/2 4.5000 114.3000
. 1.2205 31.0000 . 2.5984 66.0000 . 4.7244 120.0000
1 1/4 1.2500 31.7500 . 2.6378 67.0000 5 5.0000 127.0000
. 1.2598 32.0000 . 2.6772 68.0000 . 5.1181 130.0000
. 1.2992 33.0000 . 2.7165 69.0000 . 5.5118 140.0000
. 1.3386 34.0000 2 3/4 2.7500 69.8500 . 5.9055 150.0000
. 1.3780 35.0000 . 2.7559 70.0000 6 6.0000 152.4000
. 1.4173 36.0000 . 2.7953 71.0000 . 6.2992 160.0000
. 1.4567 37.0000 . 2.8346 72.0000 . 6.6929 170.0000
. 1.4961 38.0000 . 2.8740 73.0000 . 7.0866 180.0000
1 1/2 1.5000 38.1000 . 2.9134 74.0000 . 7.4803 190.0000
. 1.5354 39.0000 . 2.9528 75.0000 . 7.8740 200.0000
. 1.5748 40.0000 . 2.9921 76.0000 8 8.0000 203.2000
. 1.6142 41.0000 3 3.0000 76.2000 . 9.8425 250.0000
. 1.6535 42.0000 . 3.0315 77.0000 10 10.0000 254.0000
. 1.6929 43.0000 . 3.0709 78.0000 20 20.0000 508.0000
. 1.7323 44.0000 . 3.1102 79.0000 30 30.0000 762.0000
1 3/4 1.7500 44.4500 . 3.1496 80.0000 40 40.0000 1016.0000
. 1.7717 45.0000 . 3.1890 81.0000 60 60.0000 1524.0000
. 1.8110 46.0000 . 3.2283 82.0000 80 80.0000 2032.0000
. 1.8504 47.0000 . 3.2677 83.0000 100 100.0000 2540.0000

Unit Conversions
WEIGHT:
1 kg = 2.205 lbm
1 in3 of water (60°F) = 0.073551 in3 of mercury (32°F)
1 in3 of mercury (32°F) = 13.596 in3 of water (60°F)
1 in3 of mercury (32°F) = 0.1905 lbm
DENSITY:
1 lbm / in3 = 27.68 gram / cm3
1 gr / cm3 = 0.03613 lbm / in3
1 lbm / ft3 = 16.0184 kg / in3
1 kg / m3 = 0.06243 lbm / ft3
VELOCITY:
1 ft / sec = 0.3048 m / sec
1 m / sec = 3.2808 ft / sec
VOLUME:
1 gallon = 0.134 ft3
1 gallon = 231 in3
1 ft3 = 7.481 gal
1 ft3 = 1728 in3
1 lbm of water = 27.7 in3
1 lbm of water = 0.016 ft3
TEMPERATURE:
1.8 x °C + 32°= °F
0.556 (°F - 32°) = °C
LENGTH:
1 in = 25.4 mm
1 in = 2.54 cm
1 mm = 0.03937 in
1 mm = 0.00328 ft
1 micron = 0.000001 meter
1 ft = 304.8 mm
1 ft = 30.48 cm
AREA:
1 in2 = 6.452 cm2
1 cm2 = 0.155 in2
1 cm2 = 0.00108 ft2
1 ft2 = 929.03 cm2
FORCE:
1 lbf = 4.448 N
1 lbf = 0.454 kgf

Equivalents of Pressure and Head
Pressure or in. water ft. water in. mercury

lb/in² lb/ft²
Head (60°F) (60°F) (60°F)
lb/in² 1 144 27.707 2.3039 2.03601

lb/ft² 0.0069445 1 0.19241 0.01603 0.014139
in. water* 0.36092 5.1972 1 0.08333 0.073483
ft. water* 0.433103 62.3668 12 1 0.8818
in. mercury** 0.491157 70.7266 13.608 1.134 1
*Water at 60°F **Mercury at 32°F
To convert from one set of units to another, locate the given unit in the left hand
column and multiply the numerical value by the factor shown horizontally to the
right under the set of units desired.

Appendix 1
MAS Painting Specification

MAS09900-6.13

1915 25th Avenue East Palmetto, FL 34221 Ph: (941) 721-1800 Fax: (941) 721-1864
Painting Specification MAS09900-6.13 for:
Pipe Supports and Structures
Developed By: Maverick Applied Science, Inc.

1915 25th Avenue East
Palmetto, FL 34221
June 25, 2013
MAS09900-6.13
Page 2 June 25, 2013
Painting Specification for Supports Maverick Applied Science, Inc.
And Structures MAS09900-6.13
1.0 GENERAL
1.1. Scope
1.1.1. This specification covers the general requirements for cleaning,
surface preparation and painting of steel structures and equipment.
1.2. References
1.2.1. Coatings and their application shall comply with the latest revision
of the following referenced publications unless otherwise specified.
SSPC Steel Structures Painting Council
1.3. Painting Requirements
1.3.1. All coating materials shall be the product of a single manufacturer.
Not substitutions or additives from different manufacturers are
allowed without approval by the Owner.
1.3.2. If pipe support rubber lining if installed, remove and re-apply after
painting is completed.
1.3.3. Remove all fasteners and other threaded hardware prior to blasting
and painting.
1.3.4. Protect all non-metallic surfaces such as PTFE slide bearings
during blasting and painting operations.
1.3.5. Galvanized surfaces shall be prepared with Carboline Rust Bond
and painted with the appropriate paint system requirements.
2.0 PAINT MATERIALS
2.1. Paint System Selection
2.1.1. This section is applicable to the painting of non-insulated surfaces

for steel fabricated equipment.
2.1.2. The following paint systems service and usage are described as
follows:
Paint
Service Usage
System
Severe corrosive Material located in a highly acidic environments and
Type 1
service exposed to splashes, spills and outdoor conditions
Moderate corrosive Material located in a mild to moderate acidic
Type 2
service environments and exposed to outdoor conditions
Mild to non- corrosive Material located in a mild to non-corrosive
Type 3
service environments and not exposed to outdoor conditions
3.0 PAINTING SPECIFICATION
3.1. Paint
3.1.1. Paint systems consist of the following primer and finish paints:
Paint System Type 1 Type 2 Type 3

Carboline Carboline
Not Required
Primer Carbomastic 615HS Carboguard 888
Carboline Carboline Caroline

Finish Carboguard 890 Carboguard 890 Carboguard 890
3.1.2. Colors shall be determined by Owner.
4.0 EXECUTION
4.1. Cleaning of Surfaces

4.1.1. Prior to blasting, all surfaces shall be thoroughly cleaned of oil,
grease and other contaminates by solvent washer per SSPC-SP 1.
4.1.2. Weld splatter and mill scale shall be removed by mechanical
means in accordance with SSPC-SP2, Hand Tool Cleaning or SP3,
Power tool cleaning.
4.1.3. Metal surfaces shall be abrasive cleaned in accordance with the
SSPC-SP6, Commercial Blast Cleaning.
4.2. Surface Conditions Prior to Painting
4.2.1. Surfaces after blasting shall be cleaned by vacuum or blown off
with compressed air that is free of oil and water. All surfaces must
be cleaned and dried.
4.2.2. Surface temperature must not be 5ºF (2ºC) colder than ambient
temperature. Surface temperature must be at least 40ºF minimum
to 110ºF maximum when relative humidity is above 85% or when
the surface or air temperature is within 5ºF of the dew point.
4.2.3. For sandblasted surfaces, the anchoring pattern must be 1.5 to 3
mils deep.
4.3. Mixing and Thinning
4.3.1. All paints shall be thoroughly mixed prior to use (preferably with a
mechanical mixer) in accordance with the paint manufacturer’s
instructions.
4.3.2. Paint shall be diluted only with products recommended by the paint
manufacturer and in accordance with the paint manufacturer’s
instructions.
4.3.3. All additional ingredients shall be mixed in accordance with the

paint manufacturer’s mixing proportions and instructions.
4.4. Painting Application
4.4.1. Conform to SSPC-PA1 standards (shop, site and maintenance
painting) and to painting manufacturer recommendations. Prime
surfaces immediately after cleaning to avoid rust formation.
4.4.2. The primer shall be fully cured prior to the application of the finish
coat.
4.5. Paint Thickness
4.5.1. Dry film thickness (DFT) must be as follows:
Paint System Type 1 Type 2 Type 3
Primer 1.5 to 2.0 mils 1.5 to 2.0 mils N/A
Finish 2.0 to 2.5 mils 2.0 to 2.5 mils 2.0 to 2.5 mils
4.6. Inspection
4.6.1. Supplier shall provide an inspection report for each painting
operation. This report shall include:
4.6.1.1. Wet film thickness measurements per coat
4.6.1.2. Dry film measurements per coat in accordance with
SSPC PA2, Method for Determining Dry Film
Thickness of a dry film using magnetic gauge
4.6.2. Supplier shall submit inspection reports prior to shipping
equipment.
5.0 FIELD TOUCH UP FOR SHOP APPLIED COATING SYSTEM
5.1. Where only finish coat damage has occurred; power tool clean and feather
edges and recoat using the specified finish coating material.
5.2. Where coating is damaged with bare metal exposed; power tool clean and
feather edge each coating layer and recoat using the specified finish
starting with primer and then finish coat.

Termooo Standard

Uploaded by

Copyright:

Available Formats

Termooo Standard

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Termooo Standard

Uploaded by

Copyright:

Available Formats

Introduction

Maverick Applied Science provides piping engineering and pipe supports to

The Maverick Approach begins with our extraordinary group of

The Maverick Difference comes from our dual focus on pipe

Maverick pipe support designs provide:

Maverick Applied Science, Inc. 5th Edition Page 1

In addition to pipe supports, Maverick Applied Science provides engineering and

Engineering and Consulting

Maverick Applied Science, Inc. 5th Edition Page 2

Maverick Applied Science, Inc. 5th Edition Page 3

15) The standard finishes for Maverick pipe/duct supports are:

Maverick Applied Science, Inc. 5th Edition Page 4

Maverick Applied Science, Inc. 5th Edition Page 5

S10 S11 S12

S12B S12B S13

S13B S13B S14

Maverick Applied Science, Inc. 5th Edition Page 6

S14 S15 S15B

S15B S16 S17

S17 S18 S19

P10 P10L P13

Maverick Applied Science, Inc. 5th Edition Page 8

P13 P14 P14

P14 P15 P15

P16 P16 P16

Maverick Applied Science, Inc. 5th Edition Page 9

P17 P17 P18

P18 P19 P19

Maverick Applied Science, Inc. 5th Edition Page 10

Maverick Applied Science, Inc. 5th Edition Page 11

Maverick Applied Science, Inc. 5th Edition Page 12

Maverick Applied Science, Inc. 5th Edition Page 13

Maverick Applied Science, Inc. 5th Edition Page 14

(2) 180 DEG 'L2'

FASTENER 'G' 'W'

Pipe Size C G L1 L2 W Allowable Loads [lb]

Maverick Applied Science, Inc. 5th Edition Page 15

(4) HEX NUTS 'W' 'L1'

Pipe Size A B D L1 W Allowable Loads [lb]

Maverick Applied Science, Inc. 5th Edition Page 16

Pipe Size D H L1 L2 Allowable Loads [lb]

Maverick Applied Science, Inc. 5th Edition Page 17

Pipe Size C D H L1 P Allowable Loads [lb]

Maverick Applied Science, Inc. 5th Edition Page 18

Pipe Size C D H L1 P Allowable Loads [lb]

Maverick Applied Science, Inc. 5th Edition Page 19

180 DEG WEAR PAD

Pipe Size L1 Allowable Loads [lb]

Maverick Applied Science, Inc. 5th Edition Page 20

Pipe Size L1 Allowable Loads [lb]

Maverick Applied Science, Inc. 5th Edition Page 21

Pipe Size L1 L2 W Allowable Loads [lb]

Maverick Applied Science, Inc. 5th Edition Page 22

PTFE SLIDE 'L3'

Pipe Size H L1 L2 L3 W Allowable Loads [lb]

Maverick Applied Science, Inc. 5th Edition Page 23

Pipe Size C D L1 L2 Allowable Loads [lb]

Maverick Applied Science, Inc. 5Th Edition Page 24

Pipe Size C D E L1 L2 Allowable Loads [lb]