Service Manual Philips LCD Monitor 150P4 PDF

http://www.jdwxzlw.com/?
fromuser=华盛维修
15" TFT LCD Colour Monitor HUDSON 3
Service
Service
Service
150P4CG/00C(Hannstar)
Horizontal frequencies
TABLE OF CONTENTS 30 - 61 kHz
Description Page Description Page
Important Safety Notice..................................2 Colour Adjustment..........................................35~41
Technical Data & Power Management .............3~4 Repair tips......................................................42
Description of Controls Connection to PC........5 Block Diagram ................................................43
Installation & Accessories...............................6 Input DVI & D-SUB Diagram............................44
Clock & Phase Adjustments............................7 ROM Diagram.................................................45
Advanced Control of OSD...............................8 Scaler Diagram...............................................46
OSD Menu Control Level Structure..................9 Light Frame Diagram.......................................47
OSD Attention Signal.....................................10 Power Diagram...............................................48
Troubleshooting............................................11 Power board Diagram .....................................49
Failure Mode of LCD Panel............................ 12 Power board_B Diagram..................................50
Flat Panel Adjust (FP Adjust)..........................13 Power board C.B.A..........................................51
Definition of Pixel Defects..............................14 Scaler board C.B.A.........................................52~53
Wiring Diagram..............................................15 Component MAP and ROM waveform...............54
Mechanical Instructions.............................. ...16~18 Control board Diagram and (C.B.A)..................55~56
Electrical Instructions.....................................19 Exploded View................................................57
Factory Adjustment........................................ 20 Recommended Parts List.................................58
Safety Test Requirements...............................21 Spare Parts List..............................................59~60
DDC Instructions............................................22~28 General product Specification..........................61~79
DDC Data.......................................................29~32 General Trouble Shooting Guide......................80~97
Repair Flow Chart...........................................33~34 Appendix-spare parts different list....................98
SAFETY NOTICE
ANY PERSON ATTEMPTING TO SERVICE THIS CHASSIS MUST FAMILIARIZE HIMSELF WITH THE CHASSIS
AND BE AWARE OF THE NECESSARY SAFETY PRECAUTIONS TO BE USED WHEN SERVICING ELECTRONIC
EQUIPMENT CONTAINING HIGH VOLTAGES.
CAUTION: USE A SEPARATE ISOLATION TRANSFORMER FOR THIS UNIT WHEN SERVICING.
REFER TO BACK COVER FOR IMPORTANT SAFETY GUIDELINES
Published by BCU Monitor Printed in Taiwan Copyright reserved Subject to modification M Mar 15 2003 GB 3138 106 10263
家电维修资料网，免费下载各种维修资料
http://www.jdwxzlw.com/?fromuser=华盛维修
2 150P4 LCD Important Safety Notice
Go to cover page
Proper service and repair is important to the safe, reliable

FOR PRODUCTS CONTAINING LASER :
operation of all Philips Consumer Electronics Company**
Equipment. The service procedures recommended by DANGER- Invisible laser radiation when open.
Philips and described in this service manual are effective AVOID DIRECT EXPOSURE TO BEAM.
methods of performing service operations. Some of these
CAUTION- Use of controls or adjustments or
service operations require the use of tools specially designed performance of procedures other than
for the purpose. The special tools should be used when and those specified herein may result in
as recommended. hazardous radiation exposure.
It is important to note that this manual contains various CAUTION- The use of optical instruments with this
CAUTIONS and NOTICES which should be carefully read in product will increase eye hazard.
order to minimize the risk of personal injury to service
personnel. The possibility exists that improper service
methods may damage the equipment. It is also important to
understand that these CAUTIONS and NOTICES ARE NOT
EXHAUSTIVE. Philips could not possibly know, evaluate and
advise the service trade of all conceivable ways in which TO ENSURE THE CONTINUED RELIABILITY OF THIS
PRODUCT, USE ONLY ORIGINAL MANUFACTURER'S
service might be done or of the possible hazardous REPLACEMENT PARTS, WHICH ARE LISTED WITH THEIR
consequences of each way. Consequently, Philips has not PART NUMBERS IN THE PARTS LIST SECTION OF THIS
undertaken any such broad evaluation. Accordingly, a SERVICE MANUAL.
servicer who uses a service procedure or tool which is not
recommended by Philips must first satisfy himself thoroughly
that neither his safety nor the safe operation of the equipment
will be jeopardized by the service method selected. Take care during handling the LCD module with backlight
unit
* * Hereafter throughout this manual, Philips Consumer
Electronics Company will be referred to as Philips.
- Must mount the module using mounting holes arranged in four
corners.
- Do not press on the panel, edge of the frame strongly or electric
shock as this will result in damage to the screen.
WARNING - Do not scratch or press on the panel with any sharp objects, such
as pencil or pen as this may result in damage to the panel.
Critical components having special safety characteristics are - Protect the module from the ESD as it may damage the electronic
circuit (C-MOS).
identified with a by the Ref. No. in the parts list and
- Make certain that treatment person s body are grounded through
enclosed within a broken line* wrist band.
(where several critical components are grouped in one area) - Do not leave the module in high temperature and in areas of high
along with the safety symbol on the schematics or humidity for a long time.
exploded views. - Avoid contact with water as it may a short circuit within the module.
- If the surface of panel become dirty, please wipe it off with a soft
Use of substitute replacement parts which do not have the material. (Cleaning with a dirty or rough cloth may damage the
panel.)
same specified safety characteristics may create shock, fire,
or other hazards.
Under no circumstances should the original design be

modified or altered without written permission from Philips.
Philips assumes no liability, express or implied, arising out of
any unauthorized modification of design.
Servicer assumes all liability.
* Broken Line
Technical Data 150P4 LCD 3
Go to cover page
Technical Specifications
Pin Assignment
LCD Panel
Type : TFT LCD
Screen size : 15" Visual The digital only connector contains 24 signal contacts organized in three rows of eight
Pixel pitch : 0.297 x 0.297 mm(15.0")
LCD Panel type : 1024x 768 pixels contacts. Signal pin assignments are listed in the Table:
R.G.B. Vertical stripe
Anti0glare polarizer, hard coated Pin Signal Pin Signal Pin Signal
Effective viewing area : 304.1 X 228.1 mm(15.0") No. Assignment No. Assignment No. Assignment
Display Colors : 16.7M colors
T.M.D. S. T.M.D.S. T.M.D.S.
SCANNING 1 9 17
Horizontal scan range : 30 kHz to 61 kHz (automatic)
Data2 - Data1 - Data0 -
Vertical scan range : 56 Hz to 76 Hz (automatic)
T.M.D.S. T.M.D.S. T.M.D.S.
2 10 18
Video Data2+ Data1+ Data0+
Video dot rate : 80MHz
input impedance T.M.D.S. T.M.D.S. T.M.D.S.
3 11 19
-Video : 75 ohms Data2/4 Shield Data1/3 Shield Data0/5 Shield
-Sync : 2 KOhm
Input signal levels : 700m Vpp 4 No connect 12 No connect 20 No connect
Sync input signals : Separate sync
composite sync 5 No conn ect 13 No connect 21 No connect
Sync on Green
T.M.D.S. Clock
Sync polarities : Positive and negative 6 DDC Clock 14 +5V Power 22
Input Frequency : XGA Hsync Shield
48-61 KHz,Vsync 60-76Hz(N.I.)
SVGA Hsync Ground (for T.M.D.S.
7 DDC Data 15 23
35-50 KHz,Vsync 56-75Hz(N.I.) +5V) Clock+
VGA Hsync
31-38 KHz,Vsync 60-76Hz(N.I.) Hot Plug T.M.D.S.
8 No connect 16 24
Video interface : Dual input:Both Analog(D-Sub) and Detect Clock -
DVI-D (Digital only) are available.
It can be switched via OSD selection
Resolution and Preset Modes

Maximum : 1024 x 768 at 75Hz
Recommended : 1024 x 768 at 60Hz
2. The 15-pin D-sub connector (male) of the signal cable
Optical Characteristics
Contrast ratio : 400(typ.)
2
Brightness : 250 cd/m (typ.)
,
Peak contrast angle : 6 o clock
o
White chromacity : x:0.283 y:0.297 (at 9300 k)
o
x:0.313 y:0.329 (at 6500 k)
x:0.313 y:0.329 (at sRGB)
o
Viewing angle (CR>5) : Upper>=50° (typ.)Lower>=60 (type)
Left and Right >=75° (typ.)
Response time : <=25ms(typ.)
Pin Pin
Assignment Assignment
Physical Characteristics No. No.
Dimensions(WXHXD) :343x297x218mm(incl.pedestal)
1 Red video input 9 DDC+5V
Weight (monitor only) : 3.6 kg
Tilt Forward / Backward
o
: -5 / 25
o
2 Green video input 10 Logic ground
AC input voltage / frequency : 100 to 240 VAC / 50 or 60 Hz Identical output-
Power consumption : 20 W (typ.) 3 Blue video input 11
connected to pin 10
Temperature (Operating) : 5°C to 40°C
Relative Humidity : 20% to 80% Identical output- Serial data line
4 12
connected to pin 10 (SDA)
Pin Assignment 5 Cable detect 13 H. Sync / H+V
DVI-D connector 6 Red video ground 14 V. Sync
(Digital Visual Interface - Digital) 7 Green video ground 15 Data clock line (SCL)
8 Blue video ground
16
17
4 150P4 LCD Technical Data
Go to cover page
Automatic Power Saving

If you have VESA's DPMS compliance display card or software
installed in your PC, the monitor can automatically reduce power
consumption when power saving function active. And if an input
from keyboard, mouse or other input devices is detected, the
monitor will automatically "wake up". The following table shows
the power consumption and signaling of this automatic power
saving feature :
Power Management Definition
VESA's mode POWER LED

VIDEO H-SYNC V-SYNC USED COLOR
ON Active Yes Yes < 30 W Green
OFF Blanked No Yes <1W Amber
This monitor is Environmental Protection Agency (EPA) Energy Star

compliant and TCO'99 power management compatible.
*Zero power consumption in OFF mode can only be achieved by
disconnecting the mains cable from the monitor.
ENERGY STAR is a U.S. registered mark. AS AN ENERGY STAR

PARTNER, PHILIPS HAS DETERMINED THAT THIS PRODUCT
MEETS THE ENERGY STAR GUIDELINES FOR ENERGY
EFFICIENCY.
Data Storage
Factory preset mode:

This monitor has 14 factory-preset modes as indicated in the
following table :
Mode Resol H. freq. / V. freq Standard

ution
1. 640 x 350 31.469Khz/70.087Hz VGA
2. 720 x 400 31.469Khz/70.087Hz VGA
3. 640 x 480 31.469Khz/59.940Hz VGA
4. 640 x 480 35.000Khz/66.667Hz Macintosh
5. 640 x 480 37.861Khz/72.809Hz VESA
6. 640 x 480 37.500Khz/75.000Hz VESA
7. 800 x 600 35.156Khz/56.250Hz VESA
8. 800 x 600 37.879Khz/60.317Hz VESA
9. 800 x 600 48.077Khz/72.188Hz VESA
10. 800 x 600 46.875Khz/75.000Hz VESA
12. 1024 x 768 48.363Khz/60.004Hz VESA
13. 1024 x 768 56.476Khz/70.069Hz VESA
14. 1024 x 768 60.023Khz/75.029Hz VESA
Meanwhile, it also reverse 14 sets data space available for user

storage new timings data.
Connection to PC 150P4 LCD 5
Go to cover page
Front View Note:

If you use an Apple Macintosh, you need to connect the special
Mac adapter To one end of the monitor signal cable
Cable management
a) Remove the top cover of the arm box
b) Put the cables inside the arm box
c) Put the top cover back
UP and DOWN buttons are used when adjusting the OSD of

your monitor
LEFT and RIGHT buttons, like the UP and DOWN buttons, are
also used in adjusting the OSD of your monitor.
BRIGHTNESS hotkey. When the UP and DOWN arrow buttons

are pressed, the adjustment controls for the BRIGHTNESS will
show up.
OK button which when pressed will take you to the OSD

controls.
POWER button switches your monitor on.
Automatically adjust the horizontal position,

vertical position, phase and clock setting.
LightFrame TM hotkey for mode-switching between

full-screen mode and multi-window mode.
2) Connect to PC
(a) Turn off your computer and unplug its power cable.
(b) Connect the monitor signal cable to the video connector on the back
Please follow the steps to connect your LCD Monitor to PC. of your computer.
(c) Plug the power cord of your computer and your monitor into a nearby
1) Plug the power cord into monitor firmly outlet.
(d) Turn on your computer and monitor. If the monitor displays an image,
6 150P4 LCD Installation & Accessories
Go to cover page
Installation Locations Accessory Pack

Unpack all the parts.
Avoid Heat and Extreme Cold
1) Audio in Cable (Option only available for Multimedia version)
1. Do not store or use the LCD monitor in locations exposed to heat,
direct sunlight, or extreme cold. (Color lime)
2. Avoid moving the LCD monitor between locations with large
temperature differences. Choose a site falling within the following
temperature and humidity ranges.
Temperature: 5-400 C 41-1040F
Humidity: 20-80% RH
3. Do not subject the LCD monitor to severe vibration or high impact 2) Microphone out Cable (Option only available for Multimedia
conditions. Do not place the LCD monitor inside a car trunk. version)(color pink)
4. Take care not to mishandle this product by either knocking or
dropping during operation or transportation.
5. Do not store or use the LCD monitor in locations exposed to high
humidity or a dusty environment. Also do not allow water or other
liquids to spill on or into the LCD monitor
3) Power Cable (socket may differ for different countries)
Correct handling of the monitor

4) Macintosh Adapter (optional)
5) VGA Signal Cable
6) E-DFU package with Quick Setup Guide, Using Your Monitor

Manual, and CD-ROM.
7) Pivot CD-ROM (optional)
1. When handling the monitor, grip the bottom firmly with both hands
and ensure that the front panel faces outward before lifting. Please
refer to the diagram on the up.
2. Handling the monitor with care prevents scratching and damage. If
the monitor becomes damaged, immediately disconnect the power
from the unit and have it checked by a qualified service person before
using it again.
3. To prevent fire or electrical shock, do not drop the monitor.
4. When moving the monitor, be sure to unplug all power cords in order
to avoid injury or damage to the equipment.
CLOCK & PHASE Adjustments 150P4 LCD 7
Go to cover page
Due to the different quality of video signal generated from graphics Step 3 : Remaining Shut Down Window on the screen , follow
cards. It is necessary to adjust CLOCK and PHASE functions for the The CLOCK and PHASE adjustment instructions for the
optimal video display of LCD monitor. Following steps will guide you to optimal video display.
make correct adjustment of CLOCK and PHASE.
Step 4 : Press the button to bring up OSD menu.
However, CLOCK and PHASE functions are only available while analog
video signal is supplied. Operating unit under digital signal state, the
video clock information can be obtained from graphics cards directly.
Therefor, it is unnecessary to adjust these functions
Auto adjustment hotkey
The 150P4 has build-in a auto adjustment hotkey on the front panel, you Step 5 : Select VIDEO NOISE by press button.
may obtained a optimal video display by simply press the button and Step 6 : Press for bring up it s submenu.
save the settings. CLOCK, PHASE, Vertical position, and Horizontal
position are adjusted automatically.
Manual adjustment
If the quality of display still poor or flicker, you may also improve it by
manual adjust CLOCK and PHASE functions to eliminate the flicker.
Step 1 : Click on the Start button (Win95, Win98 or Win NT)

and choose " Shut Down...". as shown in Fig.1
Step 7 : Press or to adjust CLOCK. The picture will be jitter as

following figure, adjust CLOCK to fine-ture the video until
optimal display is obtained.
CLOCK Phenomenon
Step 8 : Press or to adjust PHASE. The picture will be jitter as

following figure, adjust PHASE and check the picture, stop at the point
that without any vertical jitter bar remaining on the screen.
Fig.1
Step 2 : The menu of " Shut Down Windows " is as shown in Fig. 2
PHASE phenomenon
Step 9 : Quit OSD menu by press button to save the settings.

Fig. 2
8 150P4 LCD Advanced control of OSD
Go to cover page
Front control panel Recover attention signals by pressing button for more than 10
seconds without video signal input.
Remark : Power light is amber color.
ATTENTION
ATTENTION SIGNAL ON
To Lock/Unlock OSD function
The OSD function can be locked by pressing button for more than
10 seconds, the screen shows following windows for 3 seconds. Access Factory Mode
In this condition, The & (brightness) , & hotkey are not
functional for brightness expectively while OSD locked To hold and buttons then power on the monitor. Press to
bring up OSD menu for confirmation as below:
ATTENTION
OSD MAIN MENU LOCKED
Locked OSD function can be released by pressing button for HUDSON 150P4 P158 2003-01-27
more than 10 seconds. While press button for OSD unlocked
In the factory mode, once video signal removed, a full white pattern
purpose, the screen will keep showing"OSD MAIN MENU LOCKED"
will be display on the screen as Fig.1 in stead of power saving mode.
until OSD function unlocked and screen automatically shows
In other words, the power saving function will be disable in the factory
following window for 3 seconds.
mode.
ATTENTION
OSD MAIN MENU UNLOCK NO VIDEO INPUT
AGING...
Switch ON/OFF attention signals Fig.1
All attention signals can be switched off by keep pressing button Leave factory mode by simply power off the monitor.
for more than 10 seconds if there is no video signal supplied.
Remark: Power light is amber color.
ATTENTION
ATTENTION SIGNAL OFF
OSD Control Structure 150P4 LCD 9
Go to cover page
The OSD Tree

Below is an overall view of the structure of the On-Screen Display. You can use this as a reference when you
want to work your way around the different adjustments later on.
Analog signal input:
Digital signal input:
10 150P4 LCD OSD Attention signals
Go to cover page
The monitor will detect various display situation automatically. When USE 1024 X 768 FOR BEST RESULT
the monitor detects the problems, the screen will show the different This message appears at the top of the OSD window when the video
warning signals to remind you what is happen to your monitor. mode input is not the recommended 1024x768. Other modes may
result in some picture distortion. Please adjust the video mode to
NO VIDEO INPUT 1024x768 at 60Hz for best display quality.
This screen appears if there is no video signal input. Please check
that the signal cable is properly connected to the video card of PC
and make sure PC is on.
USE 1024x768 FOR BEST RESULT
ATTENTION
NO VIDEO INPUT WAIT FOR AUTOMATIC ADJUSTMENT

This screen appears when you touch the button. It will
disappear when the monitor is properly adjusted.
ATTENTION
CANNOT DISPLAY THIS VIDEO MODE..

This screen warns when the input frequency from the computer is not WAITING FOR AUTOMATIC ADJUSTMENT
a standard video mode or out of the monitor's scanning range.
Please change the display mode of the operating software in the
computer(i.e. Windows) to 1024 x 768@ 60Hz for best display results.
ATTENTION
CANNOT DISPLAY THIS VIDEO CHECK CABLE CONNECTION

MODE, CHANGE COMPUTER DISPLAY This message appears when a signal cable is disconnected while
computer is working.
INPUT TO 1024X768@60HZ
ATTENTION
ATTENTION
CHECK CABLE CONNECTION
THIS IS 85HZ OVERSCAN,
CHANGE COMPUTER DISPLAY
INPUT TO 1024X768@60HZ
ENTERING SLEEP MODE

This screen appears when the monitor is about to enter the sleep
mode. Please press any key on the keyboard or click the mouse to
wake up the monitor and computer.
ATTENTION
ENTERING SLEEP MODE
Trouble Shooting 150P4 LCD 11
Go to cover page
TROUBLESHOOTING Horizontal flicker Push the Auto button.

appears Eliminate the horizontal bars using the Phase
This page presents problems that can be corrected by the user. If the Adjustment in the First Window.
problem still exists after these possible solutions, a further action has
to be take by authorized technicians.
No Picture Make sure the Power cable is plugged to the

(Power LED not lit) wall and back of the monitor.
Make sure the DC power cord has been
attached to the DC jack. The screen is too Adjust the contrast and brightness using the
First, power button in front of the monitor bright or too dark First Window.
should be in the OFF position, then press it to (The backlight of the LCD monitor has a fixed
ON position again. life span. When the screen becomes dark or
begins to flicker,please contact your dealer.)
No Picture Make sure the computer is turned on.

(Power LED is Make sure the signal cable is properly An after-image If an image remains in the screen for an
Amber or Green in connected to your computer. appears extended period of time,it may be imprinted in
color) Check to see if the monitor cable has bent pins. the screen and leave an after-image. This
The Energy Saving Feature may be activated. usually disappears after a few hours.
An after-image This is characteristic of liquid crystal and is

Screen says Make sure the monitor cable is properly remains after the not caused by a malfunction or deterioration
connected to your computer. power has been of the liquid crystal. The after-image will
Check to see if the monitor cable has bent pins. turned off disappear after a set amount of time.
Make sure the computer is turned on.
Green, red, The remaining dots are normal

blue, dark and charactericstic of the liquid crystal used in
white dots today's technology.
remain on the
screen
AUTO button not The Auto Function is designed for
working use on standard Macintosh or
properly IBM-compatible PC running Microsoft Windows.
It may not work properly if using
non-standard PCs or video card.
Display position Push the AUTO button.

is incorrect Adjust the image position using the Horizontal
Position & / or Vertical Position in the Second
Window.
Image vibrates Check that the signal cable is properly

on the screen connected to the graphics board or PC.
Vertical flicker Push the AUTO button.

appears Eliminate the vertical bars using the Clock
Adjustment in the FIRST Window.
12 150P4 LCD Failure Mode of LCD panel
Go to cover page
Quick reference for failure mode of LCD panel
This page presents problems that could be made by LCD panel. It is

not necessary to repair circuit board. Simply follow the Mechanical
instruction on this manual to eliminate failure by replace LCD panel
or backlight tubes. Polarizer has bubbles .
Failure description Phenomenon
Vertical block defect

Polarizer has bubbles
Vertical dim lines

..
Foreign material inside
polarizer. It shows linear or
dot shape.
Vertical lines defect

(Always bright or dark)
Concentric circle formed
Horizontal block defect
Bottom back light of LCD is

brighter than normal
Horizontal dim lines
Backlight un-uniformity
Horizontal lines defect

(Always bright or dark)
Backlight has foreign material.

..
Black or white color, linear or
circular type
Bright pixel
Has bright or dark pixel .
. .
Dark pixel
..
Flat Panel Adjust (FP Adjust) 150P4 LCD 13
Go to cover page
Fpadjust program
The Flat Panel Adjust (FPadjust) software helps you to find the best
setting for your Philips LCD monitor. It allows you to adjust the image
performance of LCD monitor, such as RESOLUTION,
AUTO ADJUSTMENT, POSITION, CONTRAST, VIDEO CLOCK and
VIDEO PHASE.
Note: Video clock and phase functions are only available for analog
video signals.
Install and Run FPadjust
In "MS Windows 95/98" environment : For example

1. Insert CD-DFU(3138 117 04771) to your CD-ROM driver.
2. Run "E:\PC\FPADJUST\SETUP.EXE" as Fig. 1. (Replace E by the
letter of your CD-ROM driver)
E:\PC\FPADJUST\SETUP.EXE
Fig. 1
3. Then follow the instructions to install the FPadjust program.
When finish, double click FPadjust icon " ", then the
FPadjust.lnk
description (can be moved by mouse) and background pattern

come on the screen for image adjustment.
FPadjust program is working as a pattern generator to provide the

pattern display on the screen for the adjustment of CONTRAST,
CLOCK, PHASE ...etc. Please follow the steps below to adjust your
PHILIPS Flat Panel Monitor for best display quality.
14 150P4 LCD Definition of Pixel Defects
Go to cover page
0. General 3. Pixel Defect Tolerances
This section explains the different types of pixel defects and In order to qualify for repair or replacement due to pixel defects
defines acceptable defect levels of each type. In order to qualify during the warranty period, a TFT LCD panel in a PHILIPS flat
for repair or replacement under warranty, the number of pixel panel monitor must have pixel or subpixel defects exceeding the
defects on a TFT LCD panel must exceed these acceptable levels. tolerances listed in the following tables.
1. Definition of Pixels and Subpixels

BRIGHT DOT
ACCEPTABLE LEVEL
DEFECTS
A pixel, or picture element , is composed of three subpixels in the
primary colors of red, green and blue. Many pixels together from MODEL 150P4 150B4 150S4
an image. When all subpixels of a pixel are lit, the three colored 1 lit subpixel None None 8 or fewer
subpixels together appear as a single white pixel. When all are 2 adjacent lit subpixels None None 3 or fewer
dark, the three colored subpixels together appear as a single black
pixel. Other combinations of lit and dark subpixels appear as 3 adjacent lit subpixels
None None 1 or fewer
(one white pixel)
single pixels of other colors.
Distance between two
None None 15 mm or more
bright dot defects*
Subpixel Subpixel Subpixel Bright dot defects within
20 mm circle
Total bright dot defects
of all types
Pixel BLACK DOT DEFECTS ACCEPTABLE LEVEL

MODEL 150P4 150B4 150S4
2. Types of Pixel Defects 1 dark subpixel 4 or fewer 4 or fewer 8 or fewer
2 adjacent dark
Pixel and subpixel defects appear on the screen in different ways. 1 or fewer 1 or fewer 3 or fewer
subpixels
Bright dot defects 3 adjacent dark

subpixels
Bright dot defects appear as pixels or subpixels that are always lit
or "on" . These are the types of bright dot defects:. Distance between two 15 mm or
15 mm or more 15 mm or more
black dot defects* more
Black dot defects within
3 or fewer 3 or fewer 3 or fewer
20 mm circle*
One lit red, green or blue subpixel Total black dot defects of
all types
TOTAL DOT DEFECTS ACCEPTABLE LEVEL

MODEL 150P4 150B4 150S4
Two adjacent lit subpixels:
- Red + Blue = Purple Total bright or black dot
- Red + Green = Yellow defects of all types
- Green + Blue = Cyan (Light Blue)
Note: 1 or 2 adjacent subpixel defects = 1 dot defect
Three adjacent lit subpixels

(One white pixel)
Black dot defects

Black dot defects appear as pixels or subpixels that are always
dark or "off" TThese are the types of black dot defects:
One dark subpixel
Two or three adjacent dark subpixels
Wiring Diagram 150P4 LCD 15
Go to cover page
16 150P4 LCD Mechanical instructions
Go to cover page
General Remove the base

Condition:
To be able to perform measurements and repairs on the circuit For VESA standard mounting applications
boards, Spread a soft mat underneath to avoid damaging the LCD
surface. 1) Remove the top cover.
Unfold base
1)Put monitor face down on the safety surface
2) Remove the three screws and then remove the base from the
LCD monitor.
2) Pull up the base
3) Remove the back cover.
Fold the base

1)Push down the head of monitor
Note: This monitor accepts a 100mmx100mm VESA-Compliant

Mounting interface
Mechnical instructions 150P4 LCD 17
Go to cover page
1. Back View as Fig.1

Remove screw on the cap of pedestal
Fig. 5
screw
Fig. 1
2. Remove Pedestal cap as Fig.2

There are 2 screws to fix between pedestal and back cover
Click
Fig. 6
screw
Fig.2
Fig. 7
3. After removing Pedestal base as Fig.3 5. Remove back cover as Fig.8 ~ 10

a. Control panel removal on the 1712 connector
b. Open click on the right side of back cover
c. Open click on the left side of back cover
Fig. 3 Fig. 8
1901 connector
4. Remove Bezel as Fig.4 ~ 7

a. Open click on the l eft down side and right down side of bezel
b. Open click on the right side and left side of bezel
c. Open click on the left up side and right up side of bezel
Click
Fig. 9
Fig. 7
Click
Click Fig. 10
Fig. 4
18 150P4 LCD Mechanical instructions
Go to cover page
6. Remove back cover see Fig.11

6-1 scaler board 9 . The service position as Fig.14
6-2 power + inverter board
6-3 remove 3 screws for replace scaler board
6-4 remove 3 screws for replace power + inverter board
Scaler board
Power + inverter board

Fig. 11 Fig. 14
7 . Remove metal frame for replace LCD panel Fig.12

7-1 remove 2 screws on left side
7-2 remove 2 screws on right side
Fig. 12
8 . The back cover that take out LCD panel Fig.13
Fig. 13
Electrical instructions 150P4 LCD 19
Go to cover page
0. General PRESET VIDEO RESOLUTION
When carry-out the electrical settings in many cases a video Factory preset video resolution
signal must be applied to the monitor. A computer with :
Dot rate (MHz) H.freq (KHz) Mode Resolution V.freq (Hz)
- ATI VGA 1024 V6-1.04/PH BETA4 interface card 25.175 31.469 IBM VGA 10h 640 * 350 70.087
- PGA 1024 (4822 212 30916), Mach 8.
28.322 31.469 IBM VGA 3h 720 * 400 70.087
- PGA 1280 (4822 212 30917), Mach 32.
- ATI GPT-1600 (4822 397 10065), Mach 64 (up to 107kHz) 25.175 31.469 IBM VGA 12h 640 * 480 59.940
30.240 35.000 MACINTOSH 640 * 480 66.667
are used as the video signal source. The signal patterns are
selected from the "service test software" package, see user 31.500 37.861 VESA 640 * 480 72.809
guide 4822 727
31.500 37.500 VESA 640 * 480 75.000
19896 (ATI1024), or 4822 727 20273 (PGA 1280), or
4822 727 21046 (GPT-1600). 36.000 35.156 VESA 800 * 600 56.250
40.000 37.879 VESA 800 * 600 60.317
0.1 With normal VGA card: 50.000 48.077 VESA 800 * 600 72.188
If not using the ATI card during repair or alignment, The service
engineer also can use this service test software adapting with 49.500 46.875 VESA 800 * 600 75.000
normal standard VGA adaptor and using standard VGA mode 57.300 49.700 MACINTOSH 832 * 624 75.000
640 x 480, 31.5 kHz/60 Hz (only) as signal source.
65.000 48.363 VESA 1024 * 768 60.004
0.2 AC/DC Measurement: 75.000 56.476 VESA 1024 * 768 70.069
The measurements for AC waveform and DC figure is based on
1024 x 768 48kHz/60 Hz resolution mode with test pattern "32 78.750 60.023 VESA 1024 * 768 75.029
gray scale".
1.General points 3. AC Adaptor
3.1Setup the AC I/P at 90VAC, and Output DC loading at 3.8 Amp,

1.1 During the test and measuring, supply a distortion free AC mains
The DC output voltage is 12 0.5 V DC
voltage to the apparatus via an isolated transformer with low
internal resistance.
3.2Adjustment is nothing to do
1.2 All measurements mentioned hereafter are carried out at a 4. Display Adjustment
normal mains voltage (90 - 132 VAC for USA version, 195 -264
VAC for EUROPEAN version, or 90 - 264 VAC for the model with 4.1Input signals check
full range power supply, unless otherwise stated.) In factory mode, use 64 gray level and set the R,G,B sub gain to
100%.
1.3 All voltages are to be measurement or applied with respect to
ground, unless otherwise stated. Note: don't use heat-sink as 4.2 Display quality test
ground. Use timing mode as described in 2.2,2.3,2.4, and use the POPO
(pixel on pixel off) pattern to adjust the clock until no stripe and
1.4 The test has to be done on a complete set including LCD panel in adjust the phase until clear picture. Check all pre-setting 14
a room with temperature of 25 +/- 5 degree C. modes.
1.5 All values mentioned in these test instruction are only applicable 4.3 Check of WHITE-D (B)
of a well aligned apparatus, with correct signal. Apply a 48kHz/60Hz signal with white pattern, set brightness
control at 100%, and contrast control at 50%. Adjust the R, G, B
1.6 The letters symbols (B) and (S) placed behind the test instruction sub_gain, for the screen center, the 1931 CIE chromaticity (X, Y)
denotes co-ordinates shall be;
(B): carried out 100% inspection at assembly line
(S): carried out test by sampling
1.7 The white balance (color temperature), has to be tested in

subdued lighted room. 9300°K 6500°K
1.8 Repetitive power on/off cycle are allowed except it should be x (center) 0.281 ± 0.005 0.312 ± 0.005
avoided within 6 sec. y (center) 0.311 ± 0.005 0.338 ± 0.005
2. Input signal
Use Minolta CA-110 for color coordinates and luminance check.
2.1 Signal type Luminance; 250 Nits (Hannstar panel) in the center of the screen.
Video : 0.7 Vp-p linear, positive polarity
Sync. : TTL level, separate, positive or negative polarity 4.4 Check the digital interface
Signal source: pattern generator format as attachment. Set the delay time to be 6 nsec.
(table 1 to 14) Reference generator : CHROMA 2200 or 2250
Check the 64 gray level color poor & noise condition.
2.2 Input signal mode
Pre-set 14 modes
20 150P4 LCD Factory Adjustment
Go to cover page
Factory Mode Adjustment
Entering Factory Adjustment Menu HUDSON 150P4

Push & buttons then power on the monitor, release them
after picture display normally. Press button to bring up OSD
SUB - BL : 0
menu of factory mode as shown below.
SUB - BRI : 170 255
SUB - CON : 100 130 160
0
9300 K : R 209 G 203 B 255
0
6300 K : R 242 G 237 B 255
SRGB : R 208 G 208 B 208 255 128
OFFSET2 : R 92 G 82 B 77
GAIN : R 133 G 134 B 132 255 m 200
AUTO-SUB : OK OSDTIMER 60
VCOM : 120 IDX : 176
OFFSET1 : R 30 G 35 B 27
LIGHT FRAME 1
SCALER : ADD : 0 VAL : 0 READWRITE
NVRAM : ADD : 0 VAL : 0 READWRITE
PANEL : HANNSTAR
800x600 @58Hz
HUDSON 150P4 P158 2003-01-27
Contrast adjustment (Sub-Contrast). Use this menu item to

Use button to select factory adjustment indication (for example: adjust the contrast gain of pre-amp ranges from 0 to 255.
Hudson 150P4 P158 2003-01-27), which is the entrance of the
factory adjustment menu, press button to access it. The window
shows as below. 9300K R G B PRESET VIDEO RESOLUTION
6500K R G B
Color temperature gain adjustment. Use these menu items to
HUDSON 150P4 adjust the RGB gains of pre-amp for different color
temperatures, ranges from 0 to 255.
SUB - BL : 0
SUB - BRI : 170 255 OFFSET R G B
SUB - CON : 100 130 160 Sub-Brightness adjustment. Use this menu item to adjust
0
9300 K : R 209 G 203 B 255 the brightness level (DC-level) of pre-amp range from 0 to
0
6300 K : R 242 G 237 B 255 255.
SRGB : R 208 G 208 B 208 255 128
OFFSET2 : R 92 G 82 B 77
(PS: The Offset R G B f unction can be used on reduce or eliminate
GAIN : R 133 G 134 B 132 255 m 200 snowy noise on the background when the resolution of video signal is
AUTO-SUB : OK OSDTIMER 60 1024 X 768 vertical 60Hz. Slightly increase or decrease the value
VCOM : 120 IDX : 176 until snowy noise completely disappear.)
OFFSET1 : R 30 G 35 B 27
LIGHT FRAME 1
PANEL : HANNSTAR
800x600 @58Hz
Use or buttons to select SUB-CON, 9300K R G B,..etc.

Use or buttons to decrease/increase the value of each item
AUTO: adjust Sub-brightness & Sub-contrast automatically.
Safety Test Requirements 150P4 LCD 21
Go to cover page
All units that are returned for service or repair must pass the 3. Equipments and Connection
original manufactures safety tests. Safety testing requires both
Hipot and Ground Continuity testing. 3.1. Equipments
For example :
HI-POT TEST INSTRUCTION - ChenHwa 9032 PROGRAMMABLE AUTO SAFETY
TESTER
- ChenHwa 510B Digital Grounding Continuity Tester
1. Application requirements - ChenHwa 901 (AC Hi-pot test), 902 (AC, DC Hi-pot test)
Withstanding Tester
1.1 All mains operated products must pass the Hi-Pot test as
described in this instruction. 3.2. Connection
* Turn on the power switch of monitor before Hipot and
1.2 This test must be performed again after the covers have Ground Continuity testing.
been refitted following the repair, inspection or modification
of the product.
Clip
2. Test method
2.1 Connecting conditions
2.1.1 The test specified must be applied between the parallel-

blade plug of the mainscord and all accessible metal Clip
parts of the product.
2.1.2 Before carrying out the test, reliable conductive

connections must be ensured and thereafter be
maintained throughout the test period.
2.1.3 The mains switch(es) must be in the "ON" position.
2.2 Test Requirements
All products should be HiPot and Ground Continuity tested as

follows:
(ChenHwa 9032 tester)
Condition HiPot Test for HiPot Test for Ground Continuity
Video cable
products where products where Test requirement
the mains input the mains input is
range is Full 110V AC(USA
range(or 220V type)
AC)
Connect the "video cable"
or "grounding screw"
Test 2820VDC 1700VDC Test current: to the CLIP on your tester.
voltage (2000VAC) (1200VAC) 25A,AC
Test time:
Test time 3 seconds 1 second 3 seconds(min.)
(min.) Resistance
required:
Trip set at 100 uA 5 mA <=0.09+R ohm, Grounding screw
current for Max. R is the
(Tester) limitation; set resistance of
at 0.1 uA for the mains cord.
Min. limitation
Ramp set at 2 Connect the power cord

time seconds to the monitor.
2.2.1 The test with AC voltage is only for production purpose,

Service center shall use DC voltage.
2.2.2 The minimum test duration for Quality Control Inspector Power outlet
must be 1 minute. No breakdown during the test.
(Rear view of monitor)
2.2.3 The test voltage must be maintained within the specified 4. Recording
voltage + 5%.
Hipot and Ground Continuity testing records have to be kept for
2.2.4 The grounding blade or pin of mains plug must be a period of 10 years.
conducted with accessible metal parts.
22 150P4 LCD
DDC Instructions
Go to cover page
General Note: The alignment box has already build-in a batteries socket for
using batteries (9V) as power source. Pull out the socket by
DDC Data Re-programming remove four screws at the rear of box. Please do not forget that
In case the DDC data memory IC or main EEPROM which storage all remove batteries after programming. The energy of batteries can
factory settings were replaced due to a defect, the serial numbers have only drive circuits for a short period of time.
to be re-programmed.
It is advised to re-soldered DDC IC and main EEPROM from the old
board onto the new board if circuit board have been replaced, in this To Printer
case the DDC data does not need to be re-programmed.
DC 8V~12V
Additional information
Additional information about DDC (Display Data Channel) may be
obtained from Video Electronics Standards Association (VESA).
Extended Display Identification Data(EDID) information may be also
obtained from VESA.
DDC EDID structure Power

For Analog interface: Standard Version 3.0 indicator
Structure Version 1.2
For Digital inferface: Standard Version 3.0 To Monitor
Structure Version 1.3 (Digital port)
System and equipment requirements
1. An i486 (or above) personal computer or compatible.
2. Microsoft operation system Windows 95/98.
3. EDID301.EXE program (3138 106 10103) as shown in Fig. 1
4. A/D Alignment kits (3138 106 10079):
A/D Alignment Kits - Digital connection
inclusion : a. Alignment box x1 (as Fig. 2)
Pin assignment
A. 15-pin D-Sub Connector
Fig. 2 1 5
6 10
11 15
Pin No. Assignment Pin No. Assignment

1 Red video input 9 +5V
2 Green video input 10 Ground
3 Blue video input 11 Ground
b. Printer cable x1 4 Ground 12 Serial data line(SDA)
c. (D-Sub) to (D-Sub) cable x1 13 H.Sync
5 No Connected
Note: The EDID301.EXE (Release Version 1.58 20000818)is a 6 Red video ground 14 V.Sync(VCLK for DDC)
windows-based program, which cannot be run in MS-DOS. 7 Green video ground 15 Data clock line(SCL)
8 Blue video ground
B. DVI-D Connector
EDID301.EXE
Fig. 1
Ver:1.58
1 8
Diskette with EDID301.EXE 9 16
17 24
To Printer Pin No. Assignment Pin No. Assignment

1 TMDS Data 2- 13 TMDS Data 3+
DC 8V~12V 2 TMDS Data 2+ 14 +5V Power
3 TMDS Data 2/4 Shield 15 Ground (+5V)
4 TMDS Data 4- 16 Hot Plug Detect
5 TMDS Data 4+ 17 TMDS Data 0-
6 DDC Clock 18 TMDS Data 0+
Power 7 DDC Data 19 TMDS Data 0/5 Shield
indicator 8 No connect 20 TMDS Data 5-
To Monitor 9 TMDS Data 1- 21 TMDS Data 5+
10 TMDS Data 1+ 22 TMDS Clock Shield
Video Card
11 TMDS Data 1/3 Shield 23 TMDS Clock+
12 TMDS Data 3- 24 TMDS Clock-
A/D Alignment Kits - Analog connection
DDC Instructions 150P4 LCD 23
Go to cover page
4. Configuration and procedure

Rear view of 150P4
There are two ICs contained serial number on the circuit board, PC
Analog Flash ROM IC (7301), and main EEPROM (7302) which
storage all factory settings. Following descriptions are the
connection and procedure for Analog Flash ROM IC , the main
EEPROM can be re-programmed along with Analog IC by
To printer port (LTP1)

enable factory memory data write function on the DDC
program (EDID301.EXE).
DC Power
To video card
Initialize alignment box 8~12 V
~
In order to avoid that monitor entering power saving mode due to
sync will cut off by alignment box, it is necessary to initialize
To
alignment box before running programming software (EDID301.EXE). Monitor
Printer
Following steps show you the procedures and connection. Port
To PC DVI-I to D-Sub
Step 1: Supply 8~12V DC power source to the Alignment box by Adapter
plugging a DC power cord or using batteries.
Step 2: Connecting printer cable and video cable of monitor as Fig. A
Fig. 3
Step 3: Run the EDID301.EXE program until the main menu appears.
This is for initialize alignment box.
PC
Rear view of 150S4
5. DDC re-programming instructions

Start on DDC program
Start Microsoft Windows.

DC Power 1. Insert the disk containing EDID301.EXE program into floppy disk
8~12 V drive.
DVI-I to D-Sub ~ 2. Click , choose Run at start menu of Windows 95/98.
Adapter
To
Monitor
Printer
Port
To PC
Video cable
Fig. A
Note: DVI-I to D-Sub adapter can be removed if graphic card of PC with

a DVI-I interface connector.
Re-programming DDC IC
Step 1: After initialize alignment box, connecting all cables and box as
Fig. 3
Step 2: Press and hold and buttons then power on the
monitor.
Step 3: Follow the steps on DDC re-programming instructions to staring
re-programming.
24 150P4 LCD DDC Instructions
Go to cover page
Loading DDC data from monitor

3. At the submenu, type the letter of your computer's floppy disk drive
followed by :EDID301 (for example, A:\EDID301.exe,)
1. Click icon on the tools bar to bring up the Configuration Setup
as shown in Fig. 5.
windows as Fig.7
2. Select the DDC2B as the communication channel.
3. Enable Factory memory data write function and fill in page address
F0 to the block.
4. Disable Software DDC function.
5. Click button to confirm your selection.
Note: The Factory memory data write function will allow EDID30 to
rewrite serial numbers both Analog DDC IC and main EEPROM to
make sure both S/N are exactly the same. You may confirm the
function by checking the S/N at Product information of the OSD
menu after restarting the monitor.
Fig. 5
4. Click button. The main menu appears (as shown on Fig. 6).
Command bar
Tools bar
Fig. 7
Status bar
6. Click icon to read DDC EDID data from monitor. The EDID
Fig. 6 codes will display on screen as following. (The EDID codes are
depend on the model.) Meanwhile, The status bar will indicate 00%
to 100% when reading.
Note:
If the connection is improper, you will see the following error
message before entering the main menu. Meanwhile, the
(read EDID) function will be disable. At this time, please make
sure all cables are connected correctly and fixedly, and the
DDC Instructions 150P4 LCD 25
Go to cover page
Note: Write DDC data to monitor

During the loading, EDID30 will verify the EDID data which just
loaded from monitor before proceed any further function, once the 1. Click icon from the tools bar to starting rewrite DDC data.
data structure of EDID can not be recognized, the following error 2. Click for confirmation.
message will appear on the screen (Fig. 8). Please confirm
following steps to avoid this message.
1. The data structure of EDID was incorrect. Save DDC data as a file
2. DDC IC that you are trying to load data is empty. Sometimes, you maybe need to save DDC data as a text file for using
3. Wrong communication channel has set at configuration setup on other DDC chip. To save DDC data, follow the steps below:
Windows.
4. Cables loosed or poor contact of connection. 1. Click icon on the tools bar and type a file name you like. The
file format is ddc type which can be open by Microsoft WordPad.
2. Click button.
Fig. 8
Load DDC data from file
1. Click from the tools bar.

2. Select the file you want to open.
Modify DDC data (Serial No.)
3. Click . Button.
1. Click icon on the toosl bar.
2. Click till the Step 7 of 9 window appears.
3. Type the new Serial No. (for example, TY00 0245000001).
4. Click till the last step window appears, then click to
exit the Step window.
TY00 0245000001
4. Now you can re-programming DDC data which you just loaded
from a file, please be confirmed that model and serial number are
correct and match with the monitor you are trying to re-write.
26 150P4 LCD
Go to cover page
Exit DDC program
1. Click file command on the command bar then select Exit.
Definition of Serial Number
T Y 0 0 0 3 11 0 0 0 0 1
Serial Number (U.S.A: 8 digit)

(Other regions: 6 digit)
Week
Year
TY Code
TY----Chungli
CX----Dong Guan
HD----Hungary
BZ----Suzhou
YA----Mexico
IO---- Raleigh
Serial number modification - EEPROM (OSD) 150P4 LCD 27
Go to cover page
When the serial number inside DDC IC has been

changed, the serial number inside EEPROM (in User
mode, the serial number of monitor can be found
by OSD as shown in Fig. 1 also.) should be changed
at the same time.
Serial number modification in EEPROM (near CPU)

for On Screen Display (Factory mode & User mode)
PRODUCT INFORMATION
SERIAL NO : 123456
RESOLUTION : 1024x768 @75Hz Fig. 2
VIDEO INPUT : ANALOG Step 2: After run a:>I2C.exe 0 TY_000082 you get below as Fig.3
The S/N change ok .
OK BACK TO MAIN CONTROLS
Fig. 1
Due to different communication structures were implement

for DDC IC and EEPROM (serial number) application as below.
(15pin D-SUB) --------- CPU --------- EEPROM (OSD -> Serial number)
I2C I2C
Update/Modify the serial number of monitor as shown in Fig. 1,

please follow the steps as below.
Hardware connection and procedure as below show. Fig. 3
Step 1 : Supply 8~12VDC power source to alignment box by
plugging a DC power cord or using batteries. Step 3: check serial number from production information in OSD menu
Step 2 : Connecting printer cable and Video cable of monitor as Fig.A => TY 000082
PC PRODUCT INFORMATION
Rear view of 150P4 SERIAL NO : 000082
RESOLUTION : 1024x768 @75Hz
VIDEO INPUT : ANALOG
OK BACK TO MAIN CONTROLS

Fig. 4
DC Power
8~12 V
DVI-I to D-Sub ~
Adapter
To
Monitor
Printer
Port
To PC
Video cable
Fig. A
From PC MS Mode to run the I2c.exe and IICINF.exe

Step 1: Run I2C.exe as Fig. 2 then follow this step to change the S/N.
Serial Number edit for Hudson3
Tools Name : I2C.EXE under MS Mode
A:>I2C.exe 0 TY_123456
Parameter1: I2C interface
0: Use printer port
1: Use DI/o port
Parameter2: Serial Number
EX: TY_123456
" _ " : Mean Space
PS: The program needs to include IICinf.exe
Version 2.11a6.01 2002-11-14 or later
28 150P4 LCD ISP CABLE for CPU
Go to cover page
Configuration and procedure

ISP (In System Program) software is provided by Genesis to upgrade
the firmware of flash ROM and Factory default data of EEPROM.
It is a DOS-based program, which cannot be run in MS-Windows.
ISP cable is for the interface between "Parallel Port of PC" and
"15 pin-D-SUB connector of Monitor".
System and equipment requirements

1. An i486 (or above) personal computer or compatible.
2. Microsoft operation system Windows 95/98 Fig. 4
=> DOS environment.
3. ISP Software (Please use latest version from philips) Step 5 : Connect ISP cable between PC and Monitor (B)as shown in
4. ISP Cable (3138 106 10213) as shown in Fig. 1 Fig. 5.
5. Set up PC Monitor as shown in Fig. 2
Step 6 : Execute ISP Software in Monitor (A) as shown in Fig. 5.
1.=> At DOS command line ,Execute ISP software GP2.exe,
C:\ISP>GP2.exe then the prompt command line appear
BD:2>
2.=>type in BD:2>batch BDISP.txt ,a group of messages
are shown Fig 6.The execution time is displayed on last line
3.=>After the prompt command line BD:2> appear again,
it means that the update procedure is complete.
4.=>Type exit to exit ISP software.
5.=>Please do AC power OFF , then power ON ,To restart CPU.
Fig. 1 => ISP CABLE : 12nc is "3138 106 10213. Remark: for debug
If show [ fail ] in any line, means error binary file name or error
PC device file. Pls check BDISP.txt and confirm file is in directory.
Then execute again.
Rear view of the monitor Attention : Do not power off your system before you finish you
Monitor (A) ISP function .
To video card
PC
Monitor (B)
Connect to Rear view of Hudson3
Mains cord
Monitor (A)
To video card
Video cable
Fig. 2
Connect to D-Sub
Mains cord
Step 1 : Make a folder in your PC as shown in Fig. 3.
For example : C:\ISP_HSP4P170
Video cable
Fig. 5
Fig. 3
Step 2 : Copy ISP Software (ISP_HSP4P170.zip) into your folder as

Shown in Fig.3.
Step 3 : Unzip isp.zip into your folder as shown in Fig. 4.
Step 4 : Copy the updated Firmware/ Factory Default data for HS
panel (for example : HSP4P170 for EEPROM) as shown in
Fig.4.
Fig. 6
DDC data of Analog 150P4 LCD 29
Go to cover page
THE DISPLAY DATA CHANNEL ( DDC ) 1/2B CONTENT INCLUDING Standard Timing Identification #4
(FOR Hannstar ANALOG) Horizontal active pixels : 1024
Aspect Ratio : 4:3
Vendor/Product Identification Refresh Rate : 60
ID Manufacturer Name : PHL
ID Product Code : 0814 (HEX.) Standard Timing Identification #5
ID Serial Number : 123456 (DEC.) Horizontal active pixels : 1024
Week of Manufacture : 44 Aspect Ratio : 4:3
Year of Manufacture : 2002 Refresh Rate : 75
EDID Version, Revision Detailed Timing #1

Version : 1 Pixel Clock (Mhz) : 65
Revision : 3 H Active (pixels) : 1024
H Blanking (pixels) : 320
Basic Display Parameters/Features V Active (lines) : 768
Video Input Definition : Analog Video Input V Blanking (lines) : 38
0.700V/0.300V (1.00Vpp) H Sync Offset (F Porch) (pixels): 24
without Blank-to-Black Setup H Sync Pulse Width (pixels) : 136
Separate Sync V Sync Offset (F Porch) (lines) : 3
Composite Sync V Sync Pulse Width (lines) : 6
Sync on Green H Image Size (mm) : 307
no Serration required V Image Size (mm) : 230
H Border (pixels) : 0
Maximum H Image Size : 30 V Border (lines) : 0
Maximum V Image Size : 23 Flags : Non-interlaced
Display Transfer Characteristic : 2.2 : Normal Display, No stereo
(gamma) : Digital Separate sync.
Feature Support (DPMS):Standby : Negative Vertical Sync.
Suspend : Negative Horizontal Sync.
Active Off
Monitor Descriptor #2
Display Type : RGB color display Serial Number : TY 123456
Preferred Timing Mode : Detailed timing block 1
Color Characteristics Monitor Descriptor #3
Red X coordinate : 0.627 Monitor Name : PHILIPS 150P
Red Y coordinate : 0.338
Green X coordinate : 0.296 Monitor Descriptor #4
Green Y coordinate : 0.596 Monitor Range Limits
Blue X coordinate : 0.149 Min. Vt rate Hz : 56
Blue Y coordinate : 0.116 Max. Vt rate Hz : 76
White X coordinate : 0.315 Min. Horiz. rate kHz : 30
White Y coordinate : 0.333 Max. Horiz. rate kHz : 63
Max. Supported Pixel : 80
Established Timings
Established Timings I :720 x 400 @70Hz (IBM,VGA) Extension Flag : 0
640 x 480 @60Hz (IBM,VGA)
640 x 480 @67Hz (Apple,Mac II) Check sum : 81 (HEX.)
640 x 480 @72Hz (VESA)
640 x 480 @75Hz (VESA)
800 x 600 @56Hz (VESA)
800 x 600 @60Hz (VESA)
Established Timings II :800 x 600 @72Hz (VESA) **********************************************************************
800 x 600 @75Hz (VESA) EDID data (128 bytes)
832 x 624 @75Hz (Apple,Mac II) **********************************************************************
1024 x 768 @60Hz (VESA)
1024 x 768 @70Hz (VESA) 0: 00 1: ff 2: ff 3: ff 4: ff 5: ff 6: ff 7: 00
1024 x 768 @75Hz (VESA) 8: 41 9: 0c 10: 14 11: 08 12: 40 13: e2 14: 01 15: 00
Manufacturer's timings : 16: 2c 17: 0c 18: 01 19: 03 20: 0e 21: 1e 22: 17 23: 78
Standard Timing Identification #1 24: ee 25: ae 26: 7d 27: a0 28: 56 29: 4b 30: 98 31: 26
Horizontal active pixels : 640 32: 1d 33: 50 34: 55 35: bf 36: ee 37: 00 38: 01 39: 01
Aspect Ratio : 4:3 40: 01 41: 01 42: 01 43: 01 44: 01 45: 01 46: 01 47: 01
Refresh Rate : 60 48: 01 49: 01 50: 01 51: 01 52: 01 53: 01 54: 64 55: 19
56: 00 57: 40 58: 41 59: 00 60: 26 61: 30 62: 18 63: 88
Standard Timing Identification #2 64: 36 65: 00 66: 33 67: e6 68: 10 69: 00 70: 00 71: 18
Horizontal active pixels : 640 72: 00 73: 00 74: 00 75: ff 76: 00 77: 20 78: 54 79: 59
Aspect Ratio : 4:3 80: 20 81: 20 82: 31 83: 32 84: 33 85: 34 86: 35 87: 36
Refresh Rate : 75 88: 0a 89: 20 90: 00 91: 00 92: 00 93: fc 94: 00 95: 50
96: 68 97: 69 98: 6c 99: 69 100: 70 101: 73 102: 20 103: 31
Standard Timing Identification #3 104: 35 105: 30 106: 50 107: 0a 108: 00 109: 00 110: 00 111: fd
Horizontal active pixels : 800 112: 00 113: 38 114: 4c 115: 1e 116: 3f 117: 08 118: 00 119: 0a
Aspect Ratio : 4:3 120: 20 121: 20 122: 20 123: 20 124: 20 125: 20 126: 00 127: 81
Refresh Rate : 75
30 150P4 LCD DDC data of Analog
Go to cover page
(FOR LG ANALOG) Horizontal active pixels : 1024
Aspect Ratio : 4:3

Version : 1 Pixel Clock (MHz) : 65
Video Input Definition : Analog Video Input V Blanking (lines) : 38
0.700V/0.300V (1.00Vpp) H Sync Offset (F Porch) (pixels): 24
without Blank-to-Black Setup H Sync Pulse Width (pixels) : 136
Separate Sync V Sync Offset (F Porch) (lines) : 3
Composite Sync V Sync Pulse Width (lines) : 6
Sync on Green H Image Size (mm) : 307
no Serration required V Image Size (mm) : 230
H Border (pixels) : 0
Maximum H Image Size : 30 V Border (lines) : 0
Maximum V Image Size : 23 Flags : Non-interlaced
Display Transfer Characteristic : 2.2 : Normal Display, No stereo
(gamma) : Digital Separate sync.
Feature Support (DPMS) :Standby : Negative Vertical Sync.
Suspend : Negative Horizontal Sync.
Active Off
Monitor Descriptor #2
Display Type : RGB color display Serial Number : TY 123456
Preferred Timing Mode : Detailed timing block 1
Color Characteristics Monitor Descriptor #3
Red X coordinate : 0.626 Monitor Name : PHILIPS 150P
Red Y coordinate : 0.347
Green X coordinate : 0.308 Monitor Descriptor #4
Green Y coordinate : 0.588 Monitor Range Limits
Blue X coordinate : 0.146 Min. Vt rate Hz : 56
Blue Y coordinate : 0.119 Max. Vt rate Hz : 76
White X coordinate : 0.313 Min. Horiz. rate kHz : 30
White Y coordinate : 0.329 Max. Horiz. rate kHz : 63
Max. Supported Pixel : 80
Established Timings
Established Timings I :720 x 400 @70Hz (IBM,VGA) Extension Flag : 0
640 x 480 @60Hz (IBM,VGA)
640 x 480 @67Hz (Apple,Mac II) Check sum : 87 (HEX.)
640 x 480 @72Hz (VESA)
640 x 480 @75Hz (VESA)
800 x 600 @56Hz (VESA)
800 x 600 @60Hz (VESA)
Established Timings II :800 x 600 @72Hz (VESA) *********************************************************************
800 x 600 @75Hz (VESA) EDID data (128 bytes)
832 x 624 @75Hz (Apple,Mac II) *********************************************************************
1024 x 768 @60Hz (VESA)
1024 x 768 @70Hz (VESA) 0: 00 1: ff 2: ff 3: ff 4: ff 5: ff 6: ff 7: 00
1024 x 768 @75Hz (VESA) 8: 41 9: 0c 10: 14 11: 08 12: 40 13: e2 14: 01 15: 00
Manufacturer's timings : 16: 2c 17: 0c 18: 01 19: 03 20: 0e 21: 1e 22: 17 23: 78
Standard Timing Identification #1 24: ee 25: 7e 26: a5 27: a0 28: 58 29: 4e 30: 96 31: 25
Horizontal active pixels : 640 32: 1e 33: 50 34: 54 35: bf 36: ee 37: 00 38: 01 39: 01
Aspect Ratio : 4:3 40: 01 41: 01 42: 01 43: 01 44: 01 45: 01 46: 01 47: 01
Refresh Rate : 60 48: 01 49: 01 50: 01 51: 01 52: 01 53: 01 54: 64 55: 19
56: 00 57: 40 58: 41 59: 00 60: 26 61: 30 62: 18 63: 88
Aspect Ratio : 4:3 80: 20 81: 20 82: 31 83: 32 84: 33 85: 34 86: 35 87: 36
Refresh Rate : 75 88: 0a 89: 20 90: 00 91: 00 92: 00 93: fc 94: 00 95: 50
96: 68 97: 69 98: 6c 99: 69 100: 70 101: 73 102: 20 103: 31
Standard Timing Identification #3 104: 35 105: 30 106: 50 107: 0a 108: 00 109: 00 110: 00 111: fd
Horizontal active pixels : 800 112: 00 113: 38 114: 4c 115: 1e 116: 3f 117: 08 118: 00 119: 0a
Aspect Ratio : 4:3 120: 20 121: 20 122: 20 123: 20 124: 20 125: 20 126: 00 127: 87
Refresh Rate : 75
DDC data of Digital 150P4 LCD 31
Go to cover page
(FOR Hannstar DIGITAL) Horizontal active pixels : 1024
Aspect Ratio : 4:3

Version : 1 Pixel Clock (Mhz) : 65
Video Input Definition : Dogiyal Video Input V Blanking (lines) : 38
H Sync Offset (F Porch) (pixels): 24
H Sync Pulse Width (pixels) : 136
Maximum H Image Size : 30 V Sync Offset (F Porch) (lines) : 3
Maximum V Image Size : 23 V Sync Pulse Width (lines) : 6
Display Transfer Characteristic : 2.2 H Image Size (mm) : 307
(gamma) V Image Size (mm) : 230
Feature Support (DPMS):Standby H Border (pixels) : 0
Suspend V Border (lines) : 0
Active Off Flags : Non-interlaced
: Normal Display, No stereo
Display Type : RGB color display : Digital Separate sync.
Standard Default Color Space:Primary color space : Negative Vertical Sync.
Preferred Timing Mode : Detailed timing block 1 : Negative Horizontal Sync.
Color Characteristics
Red X coordinate : 0.627 Monitor Descriptor #2
Red Y coordinate : 0.338 Serial Number : TY 123456
Green X coordinate : 0.296
Green Y coordinate : 0.596 Monitor Descriptor #3
Blue X coordinate : 0.149 Monitor Name : PHILIPS 150P
Blue Y coordinate : 0.116
White X coordinate : 0.315 Monitor Descriptor #4
White Y coordinate : 0.333 Monitor Range Limits
Min. Vt rate Hz : 56
Established Timings Max. Vt rate Hz : 76
Established Timings I :720 x 400 @70Hz (IBM,VGA) Min. Horiz. rate kHz : 30
640 x 480 @60Hz (IBM,VGA) Max. Horiz. rate kHz : 63
640 x 480 @67Hz (Apple,Mac II) Max. Supported Pixel : 80
640 x 480 @72Hz (VESA)
640 x 480 @75Hz (VESA) Extension Flag : 0
800 x 600 @56Hz (VESA)
800 x 600 @60Hz (VESA) Check sum : 0F (HEX.)
Established Timings II :800 x 600 @72Hz (VESA)
800 x 600 @75Hz (VESA)
832 x 624 @75Hz (Apple,Mac II)
1024 x 768 @60Hz (VESA)
1024 x 768 @70Hz (VESA)
1024 x 768 @75Hz (VESA) *********************************************************************
Manufacturer's timings : *
Standard Timing Identification #1 EDID data (128 bytes)
Horizontal active pixels : 640 *********************************************************************
Aspect Ratio : 4:3 *
Refresh Rate : 60
0: 00 1: ff 2: ff 3: ff 4: ff 5: ff 6: ff 7: 00
Standard Timing Identification #2 8: 41 9: 0c 10: 14 11: 08 12: 40 13: e2 14: 01 15: 00
Horizontal active pixels : 640 16: 2c 17: 0c 18: 01 19: 03 20: 80 21: 1e 22: 17 23: 78
Aspect Ratio : 4:3 24: ee 25: ae 26: 7d 27: a0 28: 56 29: 4b 30: 98 31: 26
Refresh Rate : 75 32: 1d 33: 50 34: 55 35: bf 36: ee 37: 00 38: 01 39: 01
40: 01 41: 01 42: 01 43: 01 44: 01 45: 01 46: 01 47: 01
Standard Timing Identification #3 48: 01 49: 01 50: 01 51: 01 52: 01 53: 01 54: 64 55: 19
Horizontal active pixels : 800 56: 00 57: 40 58: 41 59: 00 60: 26 61: 30 62: 18 63: 88
Aspect Ratio : 4:3 64: 36 65: 00 66: 33 67: e6 68: 10 69: 00 70: 00 71: 18
Refresh Rate : 75 72: 00 73: 00 74: 00 75: ff 76: 00 77: 20 78: 54 79: 59
80: 20 81: 20 82: 31 83: 32 84: 33 85: 34 86: 35 87: 36
88: 0a 89: 20 90: 00 91: 00 92: 00 93: fc 94: 00 95: 50
96: 68 97: 69 98: 6c 99: 69 100: 70 101: 73 102: 20 103: 31
104: 35 105: 30 106: 50 107: 0a 108: 00 109: 00 110: 00 111: fd
32 150S4 LCD
DDC data of Digital
Go to cover page
(FOR LG ANALOG) Horizontal active pixels : 1024
Aspect Ratio : 4:3

Version : 1 Pixel Clock (MHz) : 65
Video Input Definition : Digital Video Input V Blanking (lines) : 38
H Sync Offset (F Porch) (pixels): 24
H Sync Pulse Width (pixels) : 136
Maximum H Image Size : 30 V Sync Offset (F Porch) (lines) : 3
Maximum V Image Size : 23 V Sync Pulse Width (lines) : 6
Display Transfer Characteristic : 2.2 H Image Size (mm) : 307
(gamma) V Image Size (mm) : 230
Feature Support (DPMS) :Standby H Border (pixels) : 0
Suspend V Border (lines) : 0
Active Off Flags : Non-interlaced
: Normal Display, No stereo
Display Type : RGB color display : Digital Separate sync.
Standard Default Color Space:Primary color space : Negative Vertical Sync.
Preferred Timing Mode : Detailed timing block 1 : Negative Horizontal Sync.
Color Characteristics
Red X coordinate : 0.626 Monitor Descriptor #2
Red Y coordinate : 0.347 Serial Number : TY 123456
Green X coordinate : 0.308
Green Y coordinate : 0.588 Monitor Descriptor #3
Blue X coordinate : 0.146 Monitor Name : PHILIPS 150P
Blue Y coordinate : 0.119
White X coordinate : 0.313 Monitor Descriptor #4
White Y coordinate : 0.329 Monitor Range Limits
Min. Vt rate Hz : 56
Established Timings Max. Vt rate Hz : 76
Established Timings I :720 x 400 @70Hz (IBM,VGA) Min. Horiz. rate kHz : 30
640 x 480 @60Hz (IBM,VGA) Max. Horiz. rate kHz : 63
640 x 480 @67Hz (Apple,Mac II) Max. Supported Pixel : 80
640 x 480 @72Hz (VESA)
640 x 480 @75Hz (VESA) Extension Flag : 0
800 x 600 @56Hz (VESA)
800 x 600 @60Hz (VESA) Check sum : 15 (HEX.)
Established Timings II :800 x 600 @72Hz (VESA)
800 x 600 @75Hz (VESA)
832 x 624 @75Hz (Apple,Mac II)
1024 x 768 @60Hz (VESA)
1024 x 768 @70Hz (VESA)
1024 x 768 @75Hz (VESA) **********************************************************************
Manufacturer's timings : EDID data (128 bytes)
Standard Timing Identification #1 **********************************************************************
Horizontal active pixels : 640
Aspect Ratio : 4:3 0: 00 1: ff 2: ff 3: ff 4: ff 5: ff 6: ff 7: 00
Refresh Rate : 60 8: 41 9: 0c 10: 14 11: 08 12: 40 13: e2 14: 01 15: 00
16: 2c 17: 0c 18: 01 19: 03 20: 80 21: 1e 22: 17 23: 78
Standard Timing Identification #2 24: ee 25: 7e 26: a5 27: a0 28: 58 29: 4e 30: 96 31: 25
Horizontal active pixels : 640 32: 1e 33: 50 34: 54 35: bf 36: ee 37: 00 38: 01 39: 01
Aspect Ratio : 4:3 40: 01 41: 01 42: 01 43: 01 44: 01 45: 01 46: 01 47: 01
Refresh Rate : 75 48: 01 49: 01 50: 01 51: 01 52: 01 53: 01 54: 64 55: 19
56: 00 57: 40 58: 41 59: 00 60: 26 61: 30 62: 18 63: 88
Aspect Ratio : 4:3 80: 20 81: 20 82: 31 83: 32 84: 33 85: 34 86: 35 87: 36
Refresh Rate : 75 88: 0a 89: 20 90: 00 91: 00 92: 00 93: fc 94: 00 95: 50
96: 68 97: 69 98: 6c 99: 69 100: 70 101: 73 102: 20 103: 31
104: 35 105: 30 106: 50 107: 0a 108: 00 109: 00 110: 00 111: fd
112: 00 113: 38 114: 4c 115: 1e 116: 3f 117: 08 118: 00 119: 0a
120: 20 121: 20 122: 20 123: 20 124: 20 125: 20 126: 00 127: 15
Repair Flow Chart 150P4 LCD 33
Go to cover page
Block Diagram
AC IN No power
(power indicator off)
Power supply +inverter

board
No Power supply +
Check
12V/3.3V DC inverter board
12V DC 3.3V/12VDC
Yes
Main panel
620Vrms
Fluorescent
Lamp LCD panel
Replace Main panel
No Raster
Check No
Power+ inverter Board Front control key
Powe + inverter
Bad AC adapter does not work
board12V/3.3V/ DC
Yes
Check No Check
video signals input Video source Front control panel
interface (Key & SW)
Yes
Yes
Check Check
OK Replace fluorescent Signal connectors
Power+Inverter panel
620VAC with load lamp 1712, 1503
No Yes
Replace main panel

Replace main panel
34 150P4 LCD Repair Flow Chart
Go to cover page
Bad brightness
Check power + No
Bad power +
Inverter panel output
Inverter panel
620VAC
Yes
Replace fluorescent
lamp
No
Replace LCD panel
Bad image
Check
Video,fh/fv,DVI-D
signals
Yes
Replace main panel
No
Check
all connectors &
FFC
No
Replace LCD panel
Colour adjustment 150P4 LCD 35
Go to cover page
LCD COLOUR ANALYZER - CA110
1. SUMMARY
The LCD Colour Analyzer CA-110 was designed to upgrade the white-balanceprocess on production lines for colour LCD televisions and
computer colour LCD panels in the colour LCD industry. The CA-110 consists of a main unit and a measuring probe.
The measuring probe utilizes an optical system suitable for measurement of colour LCDs and is equipped with a viewfinder to verify
the area to be measured.
2. APPLICATIONS
* White-balance adjustment and inspection on LCD production lines.

* Quality control and shipping inspection by LCD manufacturers.
* Inspection of LCDs upon receipt by computer manufacturers.
36 150P4 LCD Colour Adjustment
Go to cover page
Go to cover page
ZERO CALIBRATION
Zero calibration is performed to determine the output of the measuring probe when no light reaches the sensor and to set this as the zero
point to which all other measurements are referenced. Zero calibration must be performed after the POWER switch has been set ON
brfore taking any measurements.
To perform zero calibration :

* Before performing zero calibration, check that the measuring probe has been connected to probe
connector P1.
Display after POWER
DARKEN PROBE switch is set to ON
-->
1. Check that the POWER switch is set to ON. Approximately 5 seconds
DARKEN PROBE
2. Set the measuring/viewing selector to the PUSH 0-CAL KEY
(viewing) position. (An image can be seen in the
-->
viewfinder, but no light will reach the sensor.) Press 0-CAL,
ZERO CALIBRATION Performing zero
3. Press 0-CAL.
-->
calibration
* If zero calibration is being performed immediately CH00 P1 Zero calibration

after the POWER switch has been set to ON, press E1 [ ] completed
0-CAL after "PUSH 0-CAL KEY" appears in the
liquid crystal display.
4. Set the measuring/viewing selector to the position.

Measurements will be started immediately.
1. POWER switch
Measuring/viewing selector
Index
3. 0-CAL
Go to cover page
SETTING MEASUREMENT AREA
Measurement areas of o 25mm and o 50mm can be selected by extending or retracting the lens barrel. The o 25mm measurement area can
I I I
be used for measuring LCDs with 2 - inch or greater diagonals: the o50mm measurement area can be used for measuring LCDs with 4 -
I
inch or greater diagonals.
Set the measurement area :
Using a slotted screwdriver, loosen the lens - barrel locking screw.
Slide the lens barrel to the position corresponding to the desired measurement area. The lens barrel should be slid in the
desired direction until it stops.
Extending the lens barrel fully sets the o 25mm measurement area: retracting the lens barrel fully sets the o 50mm
I I
measurement area.
Use the screwdriver to tighten the lens - barrel locking screw and lock the lens barrel in position.
Changing the measurement area also changes the measurement angle. this may result in differences between values
measured with the o25mm measurement area and those measured with the o50mm measurement area to the
I I
viewing - angle characteristics of the LCD. For this reason. it is recommended that the measement area be constant
for all measements.
2. Move in either direction until it stops.
1. Loosen
3. Tighten
o 25mm measurement area position

I
Lens-barrel locking screw
o 50 mm measurement area position
I
Lens barrel
Go to cover page
SETTING MEASUREMENT DISTANCE

The measurement distance (the distance from the front of the measuring probe's lens barrel to the display surface of the LCD ) should be
set using a ruler according to the procedure below.
1. Mount the measuring probe on a tripod or other stand and mount the LCD on a suitable stand.
2. While using a ruler to measure the distance from the front of the measuring probe's lens barrel to the LCD's display surface, move
the measuring probe or the LCD until the distance is the correct distance for the measurement area in use.
o 25mm o 50mm
I I
measurement area
measurement distance* 135mm+/-5mm 210mm+/-10mm
* Distance from the tip of the measuring probe's lens barrel to the
LCD's display surface.
Display surface
LCD panel
Protective glass
Measurement distance
Lens barrel
(Measurement distance-D)
3. While looking through the viewfinder, move the measuring probe or

LCD until the LCD section to be measured is inside the measurement-area
indication in the viewfinder.
Viewfinder
Measurement-area indication
Go to cover page
White Balance Adjustment 5. Adjust OSD menu to lower position of screen (i.g. adjust V-position to
value 0 at submenu of OSD Setting.
Alignment procedure 6. Setting Brightness and Contrast
- Adjust Brightness to value 70 .
1. Turn on 150P4 LCD monitor. - Adjust Contrast to value 50 .
2. Turn on the Timing/Pattern generator. See Fig. 1
Setting generator to provide CROSS-Hatch pattern at
Resolution : 1024 x 768
Timing : H= 48 KHz
V= 60 Hz
3. Preset LCD colour Analyzer CA-110

- Remove the lens protective cover of probe CA-A30.
- Set Measuring/viewing selector to Measuring position for reset
analyzer. (Zero calibration) as Fig. 2
- Turn on the colour analyzer (CA-110).
- Press 0-CAL button to starting reset analyzer . See Fig. 3 7. Switch light probe to V iewing position.
8. Move the Lens barrel forward or backward to get clear image as
shown in Fig. 4
cover (black) 9. Switch light probe to Measuring position. It should be able to
indicate colour value on the CA-110.
Clear image
Measurement/viewing selector
Measurement/viewing selector
Fig. 1 Fig. 2
Fig. 4
0-CAL 10. Setting pattern to full white picture.

11. Press then select hudson 150P4 P158 2003-01-27 by button.
12. Press to bring up submenu as following windows.
Fig. 3
4. Entering factory adjustment mode of LCD Monitor.

- To hold and buttons then power on the monitor. Press HUDSON 150P4
to bring up OSD menu for confirmation.
SUB - BL : 0
SUB - BRI : 170 255
SUB - CON : 100 130 160
0
9300 K : R 209 G 203 B 255
0
6300 K : R 242 G 237 B 255
SRGB : R 208 G 208 B 208 255 128
OFFSET2 : R 92 G 82 B 77
GAIN : R 133 G 134 B 132 255 m 200
AUTO-SUB : OK OSDTIMER 60
VCOM : 120 IDX : 176
OFFSET1 : R 30 G 35 B 27
LIGHT FRAME 1
PANEL : HANNSTAR
HUDSON 150P4 P158 2003-01-27 800x600 @58Hz
Factory mode
Note : after alignment, please reset OSD to user s mode for normal
operation. Otherwise, the monitor won t entering power saving 93000 K
mode and showing full white picture all the time as no video 13. Press or buttons to select R G B. Increase/decrease value by
signal supplied. To leave factory mode by restart the monitor. press or buttons until the X, Y co-ordinates as below:
x= 0.281 0.005
y= 0.311 0.005
Go to cover page
0
6500 K
14. Setting X, Y value listed as below:
X= 0.312 0.005
Y= 0.338 0.005
Y>= 250 nits
Alignment hits: 1. R for x value , G for y value, B for Y value on the

colour analyzer.
2. If the colour analyzer has been calibrated and preset
colour temperature in it. Please switch to correct
setting in accordance with colour settings.
15. Gray scale checking

- Switch Timing/pattern generator to
Pattern: 32 gray scale
Timing: 1024 X 768 60Hz 48KHz
- Setting both Brightness and Contrast to 50 (Value).
- Check black and white scale are visible clearly across the screen.
See Fig. 1
Fig. 1
Note: The bright scale will be saturated, if Y is too large. The dark scale
will be invisible, if Y is too small. Re-alignment or review procedure
again to correct this.
42 150P4 LCD Repair Tips
Go to cover page
0. Warning preferably be equipped with a thermal control (soldering

o
temperature: 225 to 250 C).
All ICs and many other semi-conductors are susceptible to - The chip, once removed, must never be reused.
electrostatic discharges (ESD). Careless handling during
repair can reduce life drastically. When repairing, make sure 1.4 Attachment of SMDs
that you are connected with the same potential as the mass - Locate the SMD on the solder lands by means of tweezers
of the unit via a wrist wrap with resistance. Keep components and solder the component on one side. Ensure that the
and tools also at the same potential ! component is positioned correctly on the solder lands (see
Fig.2A).
- Next complete the soldering of the terminals of the
1. Servicing of SMDs (Surface Mounted Devices) component (see Fiq. 2B).
1.1 General cautions on handling and storage Fig. 2 MOUNTING

- Oxidation on the terminals of SMDs results in poor soldering. e.g. A PAIR OF TWEEZERS
Do not handle SMDs with bare hands.
- Avoid using storage places that are sensitive to oxidation
such as places with sulphur or chlorine gas, direct sunlight, A
high temperatures or a high degree of humidity. The
SOLDER
capacitance or resistance value of the SMDs may be 0.5 - 0.8 mm
PRESURE
affected by this. SOLDERING
IRON
- Rough handling of circuit boards containing SMDs may
cause damage to the components as well as the circuit
boards. Circuit boards containing SMDs should never be
bent or flexed. Different circuit board materials expand and SOLDERING TIME
< 3 sec/side
SOLDER
0.5 - 0.8 mm B
contract at different rates when heated or cooled and the PRESURE
SOLDERING
components and/or solder connections may be damaged IRON
due to the stress. Never rub or scrape chip components as

this may cause the value of the component to change.
Similarly, do not slide the circuit board across any surface.
2. Caution when attaching SMDs
1.2 Removal of SMDs - When soldering the SMD terminals, do not touch them
- Heat the solder (for 2-3 seconds) at each terminal of the directly with the soldering iron. The soldering should be
chip. By means of litz wire and a slight horizontal force, done as quickly as possible, care must be taken to avoid
small components can be removed with the soldering iron. damage to the terminals of the SMDs themselves.
They can also be removed with a solder sucker (see Fig. - Keep the SMD's body in contact with the printed board when
1A) soldering.
Fig. 1 DISMOUNTING
- The soldering iron to be used (approx. 30 W ) should
SOLDERING
VACUUM PISTON
4822 395 10159
preferably be equipped with a thermal control (soldering
o
IRON temperature: 225 to 250 C).
e.g. WELLER - Soldering should not be done outside the solder land.
SOLDER TIP PT -H7
A - Soldering flux (of rosin) may be used, but should not be
acidic.
SOLDERING
IRON - After soldering, let the SMD cool down gradually at room
SOLDER WICK temperature.
4822 321 40042
- The quantity of solder must be proportional to the size of the
e.g. A PAIR OF TWEEZERS
solder land. If the quantity is too great, the SMD might
HEATING HEATING crack or the solder lands might be torn loose from the
B printed board (see Fig. 3).
SOLDERING Fig. 3 Examples

IRON
C
SOLDER WICK
- While holding the SMD with a pair of tweezers, take it off RIGHT
gently using the soldering iron's heat applied to each
terminal (see Fig. 1 B).
- Remove the excess solder on the solder lands by means of
litz wire or a solder sucker (see Fig. 1C).
1.3 Caution on removal

- When handling the soldering.iron. use suitable pressure and SOLDERING
IRON
be careful.
- When removing the chip, do not use undue force with the
pair of tweezers.
- The soldering iron to be used (approx. 30 W) should
150P4 LCD 43
Block diagram
http://www.jdwxzlw.com/?fromuser=华盛维修 9 Go to cover page
Hudson3 150P4 Function Block
EDID EEPROM Reset IC EEPROM

RSDS
IIC bus Panel interface
Timing control signal

Scaler chip
H/V sync CLKV/GOE/STV/LP
ADC
VGA Front & Clk F- SP
Scaler engine T-con
R/G/B
- end TTL Pacific 5
0
H/V sync Gm5115 BD chip P
i
TMDS bus TMDS R n
Front- MCU LF S
end Data Picture D CLK /
DVI Bus Data
Enhancement S
TTL bus
Address & Panel power supply

Data bus IIC bus
& control
EDID EEPROM Key pad Power
Flash ROM To each block
Control Supply +3.3V
& LED s manage +12V
44 150P4 LCD Schematic Diagram(DSUB/DVI)
9 Go to cover page http://www.jdwxzlw.com/?fromuser=华盛维修
1 2 3 4 5 6 7 8 9 10 11 12 13
1 2 3 4 5 6 7 8 9 U20 C5 6208 C9
U74 E8 6209 C9
1201 A2 6210 B5
A 1203 D3 6211 B6 A
I203 +3.3V SCALER PCB 2201 C5 6212 B7
1201 2202 C6 6213 B8
2209
100n
+3.3V 26 74320-4004 7203
3208
3202
3203
SB: 56831 x4 2203 C7 6214 B9
3214
10K
10R
M24C02
10K
10K
3219
PB: 56841 2205 A6 6215 B5
1K
8 2206 A7 6216 B6
A 1 A
VCC E0 2207 A8 6217 B7
3209
8 I202
47K
16 2 2208 A9 6218 B8
RXC- E1 2209 A4 6219 B9
B 24 3206 I206 5 3 B
3204 7 DDCSDA_D 2210 B2 6220 C3
15 SDA E2
2205
2206
2207
2208
100n
100n
100n
100n
100R RX2+ RX1+ RX0+ RXC+ DDCSCL_D 2211 B3 6221 D4
is prohibited without the written consent of the copyright
23 RXC+ 6
DVI_CABLE 100R 6 SCL 2212 B3 7202 C3
DDCSCL_D
14 7 6211 6212 6213 6214 2213 D8 7203 A4
All rights reserved. Reproduction in whole or in parts
WC_ 6210
5201 VSS BAV99 BAV99 BAV99 BAV99 BAV99 2216 D2 7211 D8
5 22 100MHZ 4 2217 D2 I202 A5
13 3207 I205
21 2218 F2 I203 A3
4 100R 2219 F2 I204 B4
2221 F4 I205 B3
330p
330p
12
2210
2211
2212
100n
C B 20 I204 B C
2225 D5 I206 A3
3 2226 E5 I210 C2
3213
11 RX2- RX1- RX0- RXC- DDCSDA_D 2227 E5 I211 D3
10K
19
2228 E5 I215 E8
RX2+ 2229 E5 I216 D5
2 10 RX1+ 6215 6216 6217 6218 6219
RX0+ +3.3V BAV99 BAV99 BAV99 BAV99 BAV99 2230 F5 I217 E5
18 RX2- 2231 E9 I218 F5
1 9 RX1- +12VCC 2232 E9 I220 F3
RX0- 2233 C2 I221 F3
BAT42W
17
6220
D 3201 C4 I222 D3 D
10K U20
25 7202 3202 A3 I223 D3
C I210 M24C02 3201 C 3203 A3
BZX84-C5V1
3204 A1
10K 3221
10K3222
8 3205 E3
1
2233
6201
2201
2202
2203
100n
100n
100n
100n
G R B VIN HIN DDCSCL DDCSDA
3215
VCC E0
10K
3206 A3
2 3207 B3
owner.
5 E1 3208 A2
ASDA 3 6203 6204 6205 6206 6207 6208 6209
SDA E2 BAV99 BAV99 BAV99 BAV99 BAV99 BAV99 BAV99 3209 A1
E 3212 E9 E
I223 6
330p2216
SCL 3213 B4
7 3214 A5
VSS WC_ 3215 C3
4 7211 3216 D2
ASCLI222 BAS32L
6221
D 74LVC14APW-T D 3217 E2
Alle rechten voorbehouden. Verveelvuldiging, geheel of
3230 I211 +3.3V 3218 D7

330p2217
14 3219 A5
2213
100n
10K VCC
3232
gedeeltelijk, is niet toegestaan dan met schriftelijke
0R05
3216
100R
2225 HS 3220 E7
F R 100R I216 RIN F
3221 C2
HSIN 3218
3231
1203 1 2
10R
100n 3222 C2
toestemming van de auteursrechthebbende.
1216-004-15S-AAC
3223 E1
3233
2226
16
12p
75R
3238 3224 E2
3217
100R
3 4 HS
6 3225 E1
11 1 U74 100R
2231
33p
7 3234 3226 E2
2227 5 6 3227 F2
ISPSDA 3223 DDCSDA 12 2 G 100R I217 GIN VS 0R05
E 8 E 3228 F3
100R 3226 100R HIN 13 3 100n
G 5202 VSIN 3220 9 8 3229 F4
G
9
3235
2228
3230 D2
12p
75R
3224 100R VIN 14 4 100MHZ

10 3212 3231 D4
3205 11 10 VS 3232 D4
ISPSCL 3225 DDCSCL 15 5
I215 100R
3236 3233 E4
330p
2232
100R 100R 100R I218 2229 13 12 3234 E4
B BIN
100n
3227
3228
2221
17 3235 E4
2K2
2K2
100n 3236 E4
3237
2230
GND
12p
75R
3237 F4
+3.3V 7
I220 VSIN 3238 E9
H 5201 B2 H
HSIN
3229
F F 5202 E3
47K
I221
6201 C5
220p
DSUB_CABLE
2218
2219
33p
6203 C5
6204 C6
6205 C7
6206 C7
EXCEPT 1201,1203 WERE CHIP COMPONENTS. 6207 C8
I I
1 2 3 4 5 6 7 8 9
933215370215
223878615649
223878615649
223878615649
223878615649
223878615649
223878615649
223878615649
319801631290
319801631290
319801631290
223886715339
223886715331
319802131030
319802131030
232270461002
319802190030
933137390215
319802131030
319802190030
933215370215
933215370215
933215370215
933215370215
933215370215
933215370215
933215370215
933215370215
933215370215
933215370215
933215370215
933215370215
933215370215
933215370215
933215370215
933215370215
CHN TYT12- SETNAME XH3L (Hudson3-150P4)

BZX84-C5V1
CLASS_NO 1 --------
Ref Des Reserved
DSUB/DVI
BAV99
BAV99
BAV99
BAV99
BAV99
BAV99
BAV99
BAV99
BAV99
BAV99
BAV99
BAV99
BAV99
BAV99
BAV99
BAV99
BAV99
330p
100n
100n
100n
100n
100n
100n
100n
0R05
0R05
J J
12p
12p
12p
33p
10K
10K
10K
3138 158 5467

1K
150P4CG/00C
2003-01-30 3
6203
6215
2201
2202
2203
2205
2206
2207
2208
2226
2228
2230
2231
2232
3201
3214
3215
3218
3219
3220
6201
6204
6205
6206
6207
6208
6209
6210
6211
6212
6213
6214
6216
6217
6218
6219
NAMEYikuan Yu/Sandy Yuan SUPERS. 5 10 130 1 *** A3

MGr CHECK********DATE 2003-01-28 KONINKLIJKE PHILIPS ELECTRONICS N.V. 2000
C
1 2 3 4 5 6 7 8 9 10 11 12 13
150P4 LCD 45
Schematic Diagram(ROM)
1 2 3 4 5 6 7 8 9 10 11 12 13
A A
1 2 3 4 5 6 7 8 9 U36 C1
1305 D9
2320 A2
2321 C5
3360 D1
SCALER PCB 3361 D1
B 3362 B3 B
3363 B3
SB: 56831 x4
3364 B4
PB: 56841 3365 E3
A A 3366 E3
3367 E4
5310 I411 +3.3V 3368 C6
+3.3V 3369 D5
100MHZ 3370 C6
I412
2320
3371 C6
100n
C C
3372 D6
3373 D6
3362
3363
3364
10K
10K
10K
3374 E2
30 32 +5V 5310 A2
+3.3V
5311 D8
DATA0 I401 13 NC1VCC 12 I413 ADDR0 5312 C8
B DQ0 A0 I442 B
DATA1 I402 14 11 I414 ADDR1 7311 7310 C2
100MHZ
DQ1 A1 7311 D7
5312
2321
100n
I403 15 10 I415 M24C16-WBN6 I401 B1
3368
3370
3371
D DATA2 ADDR2 +3.3V D
4K7
4K7
10K
DQ2 A2 8 1 1305 I402 B1
DATA3 I404 17 9 I416 ADDR3 VCC E0 JFE63173 I403 B1
DQ3 A3
I404 B1
RS232 PORT
DATA4 I405 18 8 I417 ADDR4 24C16_WP 7 2 5311 1
DQ4 A4 WC E1 I405 C1
DATA5 I406 19 7 I418 ADDR5 100MHZ TXD I446 2 I406 C1
DQ5 A5 IICSCL 3372 I444 6 3 I407 C1
DATA6 I407 20 6 I419 ADDR6 SCL E2 RXD I447 3
owner.
DQ6 A6 100R I408 E2

DATA7 U36 21 5 I420 3373 I445 5 4 I411 A2
ADDR7 IICSDA 4 I412 A4
E C DQ7 A7 SDA VSS C E
7310 27 I421 ADDR8 100R I413 B4
M29W010B-90K1 A8 I414 B4
3369
10K
26 I422 ADDR9 I415 B4
A9
23 I423 ADDR10 I416 B4
+3.3V A10 I417 C4
25 I424 ADDR11 I418 C4
A11 I419 C4
4 I425 ADDR12 I420 C4
A12
3360
3361
I421 C4
10K
10K
F 28 I426 ADDR13 F
A13 I422 C4
I427 ADDR14 I423 C4
ROM_OE 24 29 Ref Des Reserved

D OE A14 3362 319802131030 D I424 D4
M29W_WE 31 3 I428 ADDR15 10K I425 D4
WE A15 3363 319802131030
22 2 I429 10K I426 D4
BANK I427 D4
CE A16 3364 319802131030
NC0VSS 10K I428 D4
1 16 3369 319802131030 I429 D4
10K
3365
3366
3367
I442 C6
10K
10K
10K
G +3.3V 10K I408 5312 313816874261 G

100MHZ I444 D6
3374 1305 313816876941 I445 D6
JFE63173
I446 D9
+3.3V I447 D9
E E
H H
EXCEPT 1305,7311 WERE CHIP COMPONENTS.
1 2 3 4 5 6 7 8 9
I I

CLASS_NO 1 --------
ROM
J 3138 158 5467 J
150P4CG/00C
2003-01-30 3
NAMEYikuan Yu/Sandy Yuan SUPERS. 5 10 130 2 *** A3
MGr CHECK********DATE 2003-01-28 KONINKLIJKE PHILIPS ELECTRONICS N.V. 2000
C
1 2 3 4 5 6 7 8 9 10 11 12 13
46 150P4 LCD Schematic Diagram(Scaler)
1 2 3 4 5 6 7 8 9 10 11 12 U23 D7 3322 A10
U24 D7 3324 C10
U25 D7 3325 B10
U26 D7 3327 C9
U27 D7 3328 A9
U28 D7 3329 B9
1 2 3 4 5 6 7 8 9 10 11 12 13 U31 E7 3330 E8
1301 A2 3331 E8
+2.5_A +2.5_D 2301 A2 3332 E8
+3.3_A
2302 A2 3333 F8
2316 100n
7304 +3.3_A +3.3_A +3.3_D 5301 332847R 332247R Ref Des Reserved
AVDD_IMB173
AVDD_RX2181
AVDD_RX1187
AVDD_RX0193
AVDD_RXC196
AVDD_BLUE 164
AVDD_GREEN168
AVDD_RED172
AVDD_ADC160
AVDD_RPLL 150
AVDD_SDDS146
AVDD_DDDS141
VDD_RXPLL_2.5199
VDD_RX2_2.5176
VDD_RX1_2.5182
VDD_RX0_2.5188
153
155
CVDD3203
CVDD2134
VDD_DPLL_3.3148
VDD_SDDS_3.3144
RVDD8129
RVDD7111
139
2303 E10 3335 F8
RVDD6 97
RVDD5 81
RVDD4 67
RVDD3 53
RVDD2 37
CVDD1 88
CVDD0 26
RVDD1 20
B3 R4 OR4
OUT 1 5 CD 1 8 OB3 2313 202001293721
RVDD0 2
R
AVDD2_ADC_2.5
AVDD1_ADC_2.5
BLM21
2317 22n
2304 E10 3336 F8
4p72301
VDD_DDDS_3.3
PIN118330247R I350 4 R 5 10u
A A I301 118 CLKH B2 2 R 7 OB2 R5 OR5 2315 319801631090 A A 2305 E10 3337 F8
2
VDD DCLK_TCON_OCLK 10p
2302
LF_PWR 113 117PIN117 331510R 2306 F10 3338 F8
4p7
PPWR DVS_TCON_FSYNC LP 3 R 6 2330 223886715339
GND 3 4 NC PANEL_PWR 114 PBIAS 116PIN116 B1 3 R 6 OB1 R6 OR6 2307 C2 5301 A8
DHS_TCON_LP 115PIN115 33p
1301 I302 DEN_TCON_ECLK 2 R 7 2331 223886715339 2308 C2 5303 E10
SA56616-28 I303 152 330310R B0 4 R 5 OB0 R7 OR7 33p
I304 151 TCLK 110 2309 C2 5304 D10
XTAL PD47_OB7 1 R 8 2332 223886715339
33p 2355
33p 2356
33p 2357
33p 2358
23111n
3316
2310 F9 5305 E10
2315
2314
150R
HC49S 109 33p
10p
10p
PD46_OB6
33p 2330
33p 2331
33p 2343
33p 2344
14M31818HZ 108 2333 223886715339 2311 A2 5306 F10
DVI_CABLE I305206 GPIO20_HDATA3 PD45_OB5 107 33p
PD44_OB4 2312 B2 6301 B2
23121n DSUB_CABLE I306207 106 2334 223886715339 7301 D5
2313 B2
B BANK I307 208 GPIO19_HDATA2 PD43_OB3 105 33p
B
331310K LED_G I308 1 GPIO18_HDATA1 PD42_OB2 104 2335 223886715339 2314 A8 7302 F9
PANEL_ID1I309 205 GPIO17_HDATA0 PD41_OB1 103 332947R 332547R 33p 2315 A7 7303 E9
GPIO16_HFS PD40_OB0 B4 2339 223886715339

331410K ISPSCL PANEL_ID0I310 204 GPIO22_HCLK 102
OB4 G4 OG4 33p 2316 A1 7304 A2
B PD39_OG7 4 R 5 4 R 5 2340 223886715339 B 2317 A2 I301 A3
101 B5 OB5 G5 OG5
ISPSDA PD38_OG6 33p 2330 B10 I302 A3

+3.3_A 3307 6 DDC_SCL 100 3 R 6 3 R 6 2341 223886715339
7 DDC_SDA PD37_OG5 99 B6 OB6 G6 OG6 33p 2331 B11 I303 A3
10K PD36_OG4 2332 C10 I304 A3
96 2 R 7 2 R 7 2342 223886715339
2313
PD35_OG3 B7 G7 OG7
10u
95 OB7 33p 2333 C11 I305 B3

6301 I311 5 RESETn PD34_OG2 94 2343 223886715339 2334 C9 I306 B3
BAS32L PD33_OG1 1 R 8 1 R 8
33p 2334
33p 2335
33p 2359
33p 2360
C 24C16_WP I312 4 GPIO21_IRQn 93 33p C 2335 C9 I307 B3
10R PD32_OD0 2344 223886715339
2339 D10 I308 B3
33p 2332
33p 2333
33p 2351
33p 2352
92 33p
3305 PD31_OR7 2347 223886715339 2340 D11 I309 B3
3308100R 2307 RIN I313171 91 33p
100n I314170 RED+ PD30_OR6 90 2341 D11 I310 B3
GIN RED-
I315167 GREEN+ PD29_OR5 87 2348 223886715339
3309100R 2308
100n PD28_OR4 33p 2342 D11 I311 B3
I316166 GREEN- PD27_OR3 86 2349 223886715339 2343 B11 I312 C3
C 3310100R 2309 BIN I317163 85 33p C
100n I318162 BLUE+ PD26_OR2 84 2350 223886715339 2344 B11 I313 C3
BLUE-
I319137 HSYNC PD25_OR1 332747R 332447R 33p 2345 E2 I314 C3
HS PD24_OR0 83 OG3 OR3
VS I320136 VSYNC G3 1 R 8 R31 R 8 2351 223886715339 2347 D9 I315 C3
D 159 ADC_TEST 80 I376 B7 OG2 OR2 33p D 2348 D9 I316 C3
2M PD23_EB7 79 I377 B6 G2 2 R 7 R22 R 7 2352 223886715339
PD22_EB6 B5 33p 2349 D9 I317 C3
1K 3306 PD21_EB5 78 I378 OG1 OR1 2350 D9 I318 C3
174 REXT 77 I379 B4 G1 3 R 6 R13 R 6 2355 223886715339
PD20_EB4 B3 33p 2351 C11 I319 C3
3304 RXC+ 194 RXC+ PD19_EB3 76 U23 OG0 OR0 2356 223886715339
+3.3_A RXC- 195 RXC- PD18_EB2 75 U26 B2 G0 4 R 5 R04 R 5 33p 2352 C11 I320 C3
RX0+ 191 RX0+ 74 U24 B1 2357 223886715339 2353 F9 I330 D3
PD17_EB1
33p 2347
33p 2348
33p 2349
33p 2350
33p 2339
33p 2340
33p 2341
33p 2342
RX0- 192 RX0- 73 U27 B0 33p 2354 F8 I331 D3
PD16_EB0
owner.
RX1+ 185 RX1+ 2358 223886715339 2355 A9 I332 D3

RX1- 186 RX1- 7301 72 I384 G7 33p
RX2+ 179 RX2+ PD15_EG7 71 I385 G6 2359 223886715339 2356 A9 I333 D3
D E gm5115-BD PD14_EG6 33p E D
RX2- 180 RX2- 70 I386 G5 2357 A9 I335 E3
PD13_EG5 69 I387 G4 2360 223886715339 2358 A9 I336 E3
WINTN I330 39 PD12_EG4 66 I388 G3 33p
2361 1n M29W_WE I331 50 GPIO8_IRQINn PD11_EG3 G2 3301 212211805972 2359 C9 I337 E3
GPIO11 PD10_EG2 65 I389 +3.3V 5304 0R 2360 C9 I338 G3
K_LEFT I332 47 64 U25 G1 I340
2362 1n GPIO7 PD9_EG1 +3.3_A 3302 319802134790 2361 D2 I340 D10
K_RIGHT I333 46 63 U28 G0 47R
GPIO6_EXTCLK PD8_EG0 100MHZ
2304
K_OK 43 2362 D2 I341 E10
47u
23631n GPIO3_TIMER1 3303 319802131090
K_DOWN I335 42 62 I392 R7 10R 2363 E2 I342 E10

K_UP I336 41 GPIO2_PWM2 PD7_ER7 61 I393 R6 3306 232270260205
2364 1n GPIO1_PWM1 PD6_ER6 2M 2364 E2 I343 E10
LED_R I337 40 GPIO0_PWM0 PD5_ER5 60 I394 R5 5303 2365 F11 I344 F10
59 I395 R4 I341 3307 319802131030

F 2345 1n PD4_ER4 58 I396 R3 +3.3_D 10K F 2366 F11 I345 F10
PD3_ER3 7303 100MHZ
2303
ADDR15 8 57 I397 R2 IRU1206-25CY 3315 319802131090 2367 F11 I350 A8
47u
ROM_ADDR15 PD2_ER2 10R
E ADDR14 9 56 I380 R1 E 2368 F11 I376 C7

ADDR13 10 ROM_ADDR14 PD1_ER1 55 U31 R0 4 3330 319802131090
ADDR12 ROM_ADDR13 PD0_ER0 10R 2369 G7 I377 C7
11
ADDR11 12 ROM_ADDR12 11910R 3330 1 Vi MT1 Vo 3I343 5305 I342 +2.5_A
3331 319802131010
100R
2370 G8 I378 C7
ADDR10 13 ROM_ADDR11 TCON_OSP 100R
120 3331 2371 G8 I379 D7
ROM_ADDR10 TCON_OPOL 100MHZ 3332 319802131090
2305
ADDR9 14 121 HMS1_O GND ADJ 10R 2372 G8 I380 E7
47u
ADDR8 15 ROM_ADDR9 TCON_OINV 12210R 3332 STH 2 3336 319802131010
ROM_ADDR8 TCON_ESP 2373 G8 I381 F7
100R
123 3333 POL 100R 2374 G8 I384 D7
ADDR7 16 TCON_EPOL 124 HMS2_E 6301 933913910115
G ROM_ADDR7 TCON_EINV 2354 BAS32L G 2375 G8 I385 D7
3301
ADDR6 17 ROM_ADDR6 TCON_RSP2 100R
125 3335 STV1
0R
ADDR5 18 100R
126 3336 STV2 1n IRU1206-25CY 2376 G8 I386 D7
ADDR4 19 ROM_ADDR5 TCON_RSP3 10R
127 3337 CLKV 7302 +2.5_A +2.5_D 2377 G9 I387 D7
ADDR3 22 ROM_ADDR4 TCON_RCLK 49 K_AUTO
ROM_ADDR3 GPIO10_TCON_ROE3 2378 G9 I388 D7
ADDR2 23 48 I381 K_PWR 4 2379 G9 I389 D7
F ADDR1 24 ROM_ADDR2 GPIO9_TCON_ROE2 12810R 3338 GOE F
ROM_ADDR1 TCON_ROE 1 MT1 5306 I345 2380 G9 I392 E7
ADDR0 25 Vo 3
100n 2365
100n 2366
100n 2367
100n 2368
ROM_ADDR0 RXD 23531n Vi 2381 G11 I393 E7
GPIO4_UART_D1 44 I344100MHZ +2.5_D
2310
2306
GND ADJ
100n
TXD 2382 G11 I394 E7
DATA7 28 GPIO5_UART_D0 45
47u
DATA6 29 ROM_DATA7 2 2383 G11 I395 E7
DATA5 ROM_DATA6 IICSCL
H
DATA4
30 ROM_DATA5 GPIO13 52 IICSDA
H 2384 G11 I396 E7
DATA3
31
32 ROM_DATA4 GPIO12 51 2385 G12 I397 E7
DATA2 33 ROM_DATA3 201 2386 G12
DATA1 34 ROM_DATA2 CLKOUT 2387 G9
AGND_GREEN
ROM_DATA1 200 +3.3_A +3.3_D +2.5_D

AGND_RXPLL
DATA0 35 2388 G9
AGND_ADC
GND1_ADC
GND2_ADC
AGND_BLUE
SGND_ADC
AGND_RXC
ROM_DATA0 NC1 142

AVSS_DDDS
AGND_RED
AGND_RX2
AGND_RX1
AGND_RX0
AGND_IMB
AVSS_SDDS
AVSS_RPLL
VSS_DDDS
GND_RX2
GND_RX1
GND_RX0
2389 G10
VSS_SDDS
NC0 132
VSS_DPLL
ROM_OE 36 ROM_OEn RESERVED1 131 2390 G10

202CVSS4
135CVSS3
133CVSS2
89CVSS1
27CVSS0
130RVSS8
112RVSS7
98RVSS6
82RVSS5
68RVSS4
54RVSS3
38RVSS2
21RVSS1
3 RVSS0
100n 2369
100n2370
100n 2371
100n2372
100n 2373
100n 2374
100n2375
100n2376
100n 2377
100n 2378
100n2379
100n2380
100n 2387
100n2388
100n2389
100n 2390
100n2391
100n2392
100n 2393
100n2394
100n 2395
100n 2396
100n2397
100n2398
100n 2381
100n 2382
100n2383
100n2384
100n2385
100n 2386
I338 RESERVED0 2391 G10
G G
2392 G10
175
178
184
190
197
157
158
161
165
169
149
145
140
198
177
183
189
156
154
147
143
138
I I 2393 G10
2394 G10
2395 G10
2396 G11
CHN TYT12- SETNAME XH3L (Hudson3-150P4) 2397 G11
2398 G11
CLASS_NO 1 -------- 3301 F10
SCALER 3302 A7
3303 A7
J 3138 158 5467 J 3304 D2
H SCALER PCB H 3305 C2
150P4CG/00C
2003-01-30 3 3306 C2
SB: 56831 x4 3307 B2
PB: 56841 NAMEYikuan Yu/Sandy Yuan SUPERS. 5 10 130 3 *** A3 3308 C2
MGr CHECK********DATE 2003-01-28 3309 C2
KONINKLIJKE PHILIPS ELECTRONICS N.V. 2000
C
3310 C2
7 3313 B2
1 2 3 4 5 6 8 9 10 11 12 13 3314 B2
3315 A8
家电维修资料网，免费下载各种维修资料 3316 A8
1 2 3 4 5 6 7 8 9 10 11 12
150P4 LCD 47
Schematic Diagram(Lightframe)
1 2 3 4 5 6 7 8 9 10 11 12 U21 C1 3449 F5
U22 F9 3450 F11
U32 F11 3451 G10
U33 G9 3452 G10
U34 F11 3453 G1
U35 E2 3454 G2
1 2 3 4 5 6 7 8 9 10 11 12 13 U38 G12 3455 H3
U39 F11 3456 H3
7442 VDDC VDDC U40 G12 3457 H3
AME8815AEGT150 VCCA VDD VCC VCCC VDDC VDDS
U41 F10 3458 H4
SCALER PCB U42 H3 3459 H4
3463390R
34661K62 1% 3464390R
4 VCCD
+3.3VLF U43 H5 3460 H4
1%
1%
A 5445 VDDC SB: 56831 x4 A U44 H5 3461 H4
A 1 3 U72 A
U45 D4 3462 H4
G14
G15
VCC_K15 N13
A10
H15
1.5Vout100MHZ
K15
VCCC_H15 R10
Vi Vo PB: 56841
BIAS_2 L14
M1
100n 2457
100n2458
100n2459
100n 2460
100n 2461
100n2462
VDDC_A6A6
VDDC_A9A9
VDD_A3A3
VDDS_A10A4
VDDS_F2 K1
J1
VCCC_R10 R8
VDDC_L2 R2
VDDS_K1 R1
VDDC_F1F1
VDDS_A4 F2
VCCA P2
VCC_N13 P7
P9
P1
VDDC_J1 L2
GND ADJ U46 F9 3463 A10
VCCC_G15
VCC_G14
VCCC_R8
2482
2483
10u2456
VDDC_R2
2
VCCD
VDDS_R1
VDD_P1
10u
10u
BIAS_1
U47 C11 3464 A10
VCC_P7
D14
OB7U104 A14 B7 B-RSBN3E15 PANEL_ID1PANEL_ID0 U48 C11 3465 B10
B-RSBP3 E14 B_RSB_N2
100n2474
100n 2475
34650R05
OB6 A13 B6 B-RSBN2E13 B_RSB_P2 U49 D11 3466 B10
OB5 B13 B5 AU 0 0 U50 D11 3467 F9
5446 A12 B4 B-RSBP2 F14 B_RSB_N1
VCCC OB4 B-RSBN1 F13 B_RSB_P1 CPT 1 0 U51 D11 3468 F9
100MHZ OB3 B12 U52 D11 3469 F9
C12 B3
100n 2464
100n2465
100n2466
100n 2467
OB2 B-RSBP1 F12 B_RSB_N0
B B2 B-RSBN0 G13 B_RSB_P0 H.S 0 1 B U53 D11 3470 F10
10u2463
OB1 D12 B1
OB0 A11 B0 B-RSBP0 U54 D11 3471 F10
H14 Ref Des Reserved LPL 1 1 U55 D11 3472 F9

B-RSGN3 H12 2455 223878615649
B B-RSGP3 J13 B_RSG_N2 B U56 D11 3473 G9
OG7 U105 B11 100n
5447 C11 G7 B-RSGN2 J12 B_RSG_P2 2468 202001293721 U57 D11 3474 G8
VCCD OG6 B-RSGP2 J15 B_RSG_N1 1410 313816876941 U58 E11
D11 G6 10u JFE63173 3475 G8
100n 2469
100MHZ OG5
C10 G5 B-RSGN1 K14 B_RSG_P1
3495
2469 223878615649 2481 222278015658 U59 E11 3476 G9
0R05
OG4
10u2468
OG3 D10 G4 B-RSGP1 K13 B_RSG_N0 100n 470n U60 E11 3477 E5
OG2 B9 G3 B-RSGN0 K12 B_RSG_P0 2470 223878615649 3490 319802131090
B-RSGP0 100n 10R U61 E11 3478 H6
C OG1 C9 G2 2471 223858615623 3491 232270461002 C U62 E11 3479 F5
+3.3VLF 5441 OG0 D9 G1 L15 1n 1K
G0 B-RSRN3 M14 U63 E11 3480 H6
VDDS B-RSRP3 M13 B_RSR_N2 2472 319801631090 6444 933913910115 U64 E11 3481 H2
100MHZ 10p BAS32L
100n 2442
100n2443
100n 2444
100n2445
100n 2446
U21 OR7 U106 A8 B-RSRN2 M12 B_RSR_P2 U65 E11 3482 F11
10u 2441
B-RSRP2 M15 B_RSR_N1 2474 223878615649 7445 933967310685

OR6 B8 R7 100n BC848C U66 E11 3483 F11
OR5 C8 R6 B-RSRN1 N14 B_RSR_P1 2480 223878615649
D8 R5 B-RSRP1 R15 B_RSR_N0 100n U67 F11 3484 G11
C OR4 B-RSRN0 N15 B_RSR_P0 C U68 F11 3485 D4
4 OR3 A7 R4 3450 232270296001 TO PANEL
OR2 B7 R3 B-RSRP0 3497 10R LP 0R 1412 U69 F11 3486 D4
1 7441 3 5442 C7 R2 R4 B_SP 3456 319802131030 51 52 3487 G11
VCC OR1 3498 10K U70 F11
D IRU1206-25CY OR0 D7 R1 B-SP P3B_INV 10R D U71 F11 3488 G11
Vi GND ADJ Vo
100n2448
100n 2449
100n2450
100n 2451
100MHZ R0 B-INV B_RSCLK_N

L13 3457 319802131030 F_RSB_P2 50
CRC&R near 7301 B-RSCLKN B_RSCLK_P 10K U72 A3 3490 G5
10u2447
2 L12 3460 319802131030 F_RSB_N2 U47 49

PIN116 3441 47R U100 A15 HSI B-RSCLKP 10K U48 48 U73 G9 3491 G5
U101 B15 DEI 47 U75 F5 3492 E4
U89
HMS2_E 3442
PIN117 3443
47R
47R U102 B14 VSI F-RSBN3 R13P14
3461 319802131030
10K
F_RSB_P1
F_RSB_N1 U49 46 U76 F4 3493 E4
CLKH 3444 47R U103 M2 F-RSBP3 R12 F_RSB_N2 3462 319802131030 U50 45
5443 PCLKI F-RSBN2 P13 F_RSB_P2 10K 44 U77 E4 3494 E9
VDD 2472 10p F-RSBP2 P12 F_RSB_N1 F_RSB_P0 U78 F4 3495 B4
3463 232270281391 F_RSB_N0 U51 43
owner.
7443
100n 2453
100n 2454
100MHZ PACIFIC-1 F-RSBN1 R11 F_RSB_P1 390R 42 U89 D2 3496 D3

+3.3VLF +3.3VLF LDATA7 H2 D7 F-RSBP1 P11 F_RSB_N0 U52
3470 319802131030 41 U93 F9 3497 C9
2452
D 3485 3486 LDATA6 J4 10K F_RSG_P2 D

10u
E LDATA5 J2 D6 F-RSBN0 M11 F_RSB_P0 F_RSG_N2 U53 40 E U94 D4 3498 C9

LDATA4 K3 D5 F-RSBP0 3473 319802131030 U54 39
3K3 3K3 D4 10K 38 U95 E5 5441 C2
5444 LDATA3 K2 F-RSGN3 N11 N12 3475 319802131030 F_RSG_P1 U97 F12 5442 C3
D3 37
VCCA U452 2
U94
LDATA2
LDATA1
L4
L1 D2 F-RSGP3 P10 F_RSG_N2 10K F_RSG_N1 U55
U56 36 1410 H5 5443 D3
100MHZ 1 1 D1 F-RSGN2 N10 F_RSG_P2 3481 319802131030
3496
35 1412 G12 5444 D3

0R05
3 3 LDATA0 M3 10K F_RSG_P0

D0 F-RSGP2 R9 F_RSG_N1 3492 319802131010 F_RSG_N0 U57 34 2441 C2 5445 A3
2N7002 LT1 2N7002 LT1
2455
100n
F-RSGN1N9 F_RSG_P1 100R 33

7447 7448 U58 2442 C3 5446 B3

LBANK A1 A16 F-RSGP1 P8 F_RSG_N0 3493 319802131010 F_RSCLK_P 32
5448 U35 3447 3446 F-RSGN0M8 F_RSG_P0 100R 31 2443 C3 5447 B3
U77 U95 LADDR15 B1 F_RSCLK_N U59
C2 A15 2444 C3 5448 E2
+3.3VLF LADDR14 F-RSGP0 U60 30

F 100MHZ 100R IICSDA 100R IICSCL C1 A14 29 F 2445 C3 5449 F10
2470
100n
LADDR13 R7 3498 319802131090 F_RSR_P2

3492 3493 LADDR12 D3 A13 F-RSRN3 P6
10R F_RSR_N2 U61 28 2446 C3 5450 F11
D2 A12 F-RSRP3 N6 F_RSR_N2 27
E LADDR11 5444 313816874261 U62 E 2447 C3 6441 G5

100R 100R LADDR10 D1 A11 F-RSRN2 M6 F_RSR_P2 100MHZ F_RSR_P1 26
2448 C3 6442 G6
LADDR9 E4 A10 F-RSRP2 R6 F_RSR_N1 5447 313816874261 F_RSR_N1 U63 25
K_LF 347710R LADDR8 E3 A9 F-RSRN1 P5 F_RSR_P1 100MHZ U64 24 2449 C3 6443 H6
30 32 LADDR7 E1 A8 F-RSRP1 N5 F_RSR_N0 321611 F_RSR_P0 23 2450 C3 6444 G5
F3 A7 F-RSRN0 P4 5448 313816874261 22
2471
NC1VCC LADDR6 F_RSR_P0 100MHZ F_RSR_N0 U65 2451 C3 7441 C2

LDATA0
1n
13 LADDR0
12 LADDR5 G4 A6 F-RSRP0 U66 21 2452 D3 7442 A2
DQ0 A0 +3.3VLF LADDR4 G3 A5 R3 3494 10R F_SP 7444 plc_M29W010B
M29W010B F_SP 20
2453 D3 7443 D7
G
LDATA1 14 LADDR1
11 LADDR3 G2 A4 F-SP N4 F_INV LP U67 19
G
LDATA2
DQ1 A1 LADDR2 G1 A3 F-INV N7 F_RSCLK_N P+3.3V POL U108 U68 18 2454 D3 7444 F2
15 LADDR2
10 LADDR1 H4 A2 F-RSCLKN M7 F_RSCLK_P B_SP 3450 17 2455 D3 7445 G5
DQ2 7444 A2 H3 A1 F-RSCLKP 100n 2480 16 2456 A3 7446 G10
3479
LADDR0 0R U71
10K
LDATA3 17 M29W010B 9
LADDR3 A0 C15 3467 0R05 BRIGHTNESS CLKV 15 2457 A3 7447 E4
100MHZ
DQ3 A3 PWM0
5449
3468 PANEL_IDX 14
LDATA4 PWM1D15 3469 10K STV1 U69
13 2458 A4 7448 E5
F 18
DQ4 A4
8
LADDR4 WRN U109 C3 PWM2C14 10K VCOM GOE U70 F 2459 A4 I201 G10
PSEN B2 WRN U34U97 12
LDATA5 U41 11 2460 A4 U100 D5
19 7
LADDR5 WINTN 3445 100R B3 PSEN C5 LF_LED1
U22
2476 100n
DQ5 A5 GPIO_03C4 LF_LED2 U32 10
10K
347112K
U76 B5 MINTN 2461 A4 U101 D5
LDATA6 20 6
LADDR6 U78 B4 SCL GPIO_02M5U93 9 2462 A4 U102 D5
3470
P+12V 5450 U39 3482
M10 GND2_M10
DQ6 A6 3448 GPIO_01M4 U46 +3.3VLF 8

J14 GND2_J14
H LDATA7 +3.3VLF 10R C6 SDA 4R7 H 2463 B3 U103 D5

GPIO_00
B10 VSS2_B10
21 LADDR7
5 3449 10K RSTN D13 4R7 7
GND2_E12
3483
H13 VSS_H13
L3 VSS2_K4
347210K 100MHZ
VSS2_L3
N8GND2_N8
DQ7 A7 2464 B3 U104 A5
M9 VSS_M9
NC_D13 6
347310K
VSS_H1
U75 R14 3484 4R7 U40
F15NC_G12
J3 VSS_J3
D4VSS_C13
D5VSS2_D5
NC_F15
NC_P15
GNDD
K4VSS2_E2
GNDA
NC_R14E5 5 2465 B4 U105 B5

10u 2473
F4VSS_D4
N3VSS_N3
27 LADDR8
A2VSS_A2
B6VSS_A5
3488 4R7
R5VSS_R5
H1VSS_F4
VSS_B6
A8 6441 NC_E5 VCOM3487 0R
2477
4
3490
2466 B4 U106 C5
10u
U38
10R
+3.3VLF 26 LADDR9 BAS32L U33 PANEL_ID0 3
T1
A9 2 2467 B4 U107 H4
PANEL_PWR PANEL_ID1
G12
C13
347510K P15
E12
3451+3.3VLF 2468 B3 U108 F11

N1
N2
D6
A5
1
E2
23 LADDR10
A10 2469 B3 U109 F5
2481 3491 100K 2470 E2
2479
25 LADDR11 7445
2478
10u
G G
10u
A11 347410K
345310K
345410K
1K BC848C +3.3VLF U73 7446 2471 E4

I 4 LADDR12 470n BC858C I
BAS32L
2472 D5
6444
A12
28 LADDR13 10K3476 3452
BL_CONTROL 2473 G6
A13 6442 2474 A10
BAV99 I201 1K
PSEN 24 29 LADDR14 2475 A10
OE A14 CHN TYT12- SETNAME XH3L (Hudson3-150P4) 2476 F10
WRN 31 3 LADDR15 +3.3V 2477 G10
WE A15 1410 CLASS_NO 1 --------
22 2 LBANK JFE63173 3478 2478 G11
CE
NC0VSS
A16 U107 1 U43 220R IICSDA
LIGHT FRAME
2479 G11
345510K
345610K
345710K
345810K
345910K
346010K
346110K
346210K
2480 F10
IIC PORT
J 1 16 2 3138 158 5467 J 2481 G4

H +3.3V +3.3V H 2482 A1
+3.3VLF U42 3 150P4CG/00C
2003-01-30 3 2483 A3
10K 3481 4 3480 IICSCL 3441 D5
220R 6443 NAMEYikuan Yu/Sandy Yuan SUPERS. 5 10 130 4 *** A3 3442 D5
U44 3443 D5
EXCEPT 1410 WERE CHIP COMPONENTS. BAV99 MGr CHECK********DATE 2003-01-28 KONINKLIJKE PHILIPS ELECTRONICS N.V. 2000
C
3444 D5
7 3445 F5
1 2 3 4 5 6 8 9 10 11 12 13 3446 E4
3447 E4
家电维修资料网，免费下载各种维修资料 3448 F5
1 2 3 4 5 6 7 8 9 10 11 12
48 150P4 LCD Schematic Diagram(Power)
1 2 3 4 5 6 7 8 9 10 11 12 13
1 2 3 4 5 6 7 8 9 U1 D2 3504 D4
U2 C1 3505 E4
U3 E6 3506 E4
A U4 F3 3507 E4 A
SCALER PCB U5 D2 3508 E4
3542 F_INV +3.3V
+3.3VLF U6 D2 3509 F4
SB: 56831 x4 2 10K U7 D2 3510 E2
3525 +12VCC +3.3V U8 B1 3511 A8
PB: 56841 7507 I589 LF_LED2
3511
BC858C 7504 U9 A1 3513 F4
10K
I587 1 10K 10K U84 3535
3 7503 SI5441DC U10 B1 3514 D8
A 10K I588 3534 47K MUN2211J U91 A U11 E2 3515 F3
1502 2 G S U12 E2 3516 C4
2511
100n
63390 3532 7512 4 5
B 1 BC858C LF_PWR U13 E2 3517 C4 B
3533
2514
2507
100n
1 U14 E2 3518 C4
10n
10K
7511 3 D3 D4
5502 3 U15 E2 3519 C4
BLM21 BRIGHTNESS 6
3523
220R
2 MUN2211J U16 B1 3520 C4
3 U9 5504BLM21 BL_CONTROL D2 D5 U17 E2 3521 C5
3536 U81 2 7
TO POWER BOARD 8052
U18 B1 3522 C5
4 U19 5505
BLM21 PANEL_IDX U19 B1 3523 A4
3543 820R D1 D6
2535
+3.3VLF B_INV 1 U29 C9 3524 C4
PWR_SAVING 8
1n
5 U18
10K U30 F6 3525 A5
2534
2
U96 3526
1n
C B 6 U10 7508 LF_LED1 B U79 C6 3526 B5 C
+12VCC BC858C +3.3VLF U80 B4 3527 E7
7 U16 5501 U80 3 1 10K 10K U82 3540 I590 +12VCC +3.3V U81 B6 3528 F7
+3.3V
8 100MHZ 10K U83 3539 47K U82 B6 3529 D8
2501
2502
2503
100n
100n
470u
U8 2 U83 B5 3530 B8
2512
100n
3537 7514 U84 A6 3531 C8
3530
9 BC858C 7506
10K
7513 1
3538
2516
100n
U85 D2 3532 A5
10K
5503 +3.3V MUN2211J 3 SI5441DC
3524
10
220R
U86 D2 3533 A5
3K3 U110
100MHZ G S U87 D2 3534 A6
2505
2506
2504
100n
100n
470u
U2 U79 4 5 U88 F6 3535 A6

D 3531 D
3541 U99 U90 E6 3536 B6
2509
10n
D3 D4 U91 C7 3537 B5
820R 3 6
25371n
C C U91 E7 3538 C5
+3.3V
2536
U91 A8 3539 B6
3516 10K
3517 10K
3518 10K
3519 10K
3520 10K
3521 10K
3522 10K
1n 7505
2
D2 D5
MUN2211J 7 U91 C8 3540 B6
U91 D8 3541 C6
D1 D6 U92 E9 3542 A5
owner.
1503 3501 I574 K_AUTO 1 8

63393 U96 B5 3543 B5
U29 1502 C1
E 1 2515 100R PANEL_PWR 3544 3544 D7 E
U86 P+3.3V 1503 C1 3545 E7
2 U87 1n 3502 I575 K_OK 100K 2501 B1 5501 B1
BAS32L 2502 B2 5502 A1
3 U1 2517 100R +12VCC 2503 B2 5503 C1
2508
6503
4u7
4 1n 3503 K_DOWN 2504 C2 5504 B1
D U85 D 2505 C1 5505 B1
+12VCC
2519 100R 2506 C2 5506 F3
3514
100K
5 U5 7510
TO CONTROL BOARD 1901
SI5441DC 2507 A8 6501 F4

3504 K_UP
6 U6 1n 2508 D7 6502 F4
F 100K U37 F
7 2521 100R G S 2509 C8 6503 D7
U7 4 2510 E7 6504 E7
3529 5
8 1n 3505 K_LEFT PANEL_PWR 3545 U98 2511 A4 7501 E6
2513
100n
U11
D3 D4 2512 B4 7502 F6
9 U12 2523 100R 10K 3 6
6504 7509 2513 E8 7503 A8
10 U13 3510 1n 3506 K_RIGHT MUN2211J D2 D5 2514 A5 7504 A9
BAS32L 2 7 2515 D3 7505 C7
2510
4u7
11 0R 2525 100R 2516 C5 7506 B9
E +3.3V D1 D6 E
G U15 1 2517 D3 7507 A4 G
12 1n 3507 K_PWR 8 2519 D3 7508 B4
U14 2527 2 U92 2521 D3 7509 D7
13 100R U90 3527 LED_R
P+12V 2523 E3 7510 D9
U17 1n 3508 1 10K 2525 E3 7511 A6
3
2529 2530 7501 2527 E3 7512 A7
220R U3 BC858C 2528 F5 7513 B6
3509 +3.3V 2529 F3 7514 B7
1n 1n
2530 F5 I574 C5
2531 220R 25281n
6502 BAS32L
H 2 2531 F3 I575 D5 H
6501 BAS32L
1n U30 3528 LED_G 2532 F3 I587 A4

3515 U88 1 10K 2533 F3 I588 A5
F PWR_SAVING 3 F 2534 B3 I589 A5
100R 1n 7502 2535 B7 I590 B7
BC858C 2536 C3
5506 U4 2532 K_LF 2537 C7
100MHZ 2533 1n 3513 3501 C4
LBANK 3502 D4
I 0R05 3503 D4 I
3 4
1 2 5 6 7 8 9
223878615649
223878615649
223878615649
223858615623
223858615623
223858615623
223858615623
319802131030
223858615623
319802190030
319802131010
319802132210
319802132210
319802131030
933913910115
933913910115

CLASS_NO 1 --------
Ref Des Reserved
BAS32L
BAS32L
POWER
100n
100n
100n
0R05
100R
220R
220R
J 3138 158 5467 J

10K
10K
1n
1n
1n
1n
1n
150P4CG/00C
2003-01-30 3
2511
2512
2513
2528
2530
2532
2535
2537
3513
3515
3523
3524
3542
3543
6501
6502
NAMEYikuan Yu/Sandy Yuan SUPERS. 5 130 5 A3

CHECK DATE 2003-01-28 KONINKLIJKE PHILIPS ELECTRONICS N.V. 2000
C
1 2 3 4 5 6 7 8 9 10 11 12 13
150P4 LCD 49
Schematic Diagram(Power board_A)
1 2 3 4 5 6 7 8 9 10 11 12 13
1101 A1 2053 D4 2103 A3 2108 A6 2114 A9 2119 C9 3101 A5 3106 B5 3111 C4 3116 A6 3121 A8 3126 C8 3131 E8 4102 A8 5102 B7 6103 A4 6108 D2 6114 E10 7104 D7 8052 C1 F103 A5 I115 A8 I120 D8
1102 A2 2054 E1 2104 A3 2109 B3 2115 A9 2120 A10 3102 A4 3107 B5 3112 C4 3117 C6 3122 C10 3127 D9 3133 E3 4103 C8 5103 A7 6104 A5 6110 D4 6115 A9 7106 D7 8102 B1 F104 A5 I116 A9 I121 B8
A 1105 A10 2055 E2 2105 A5 2111 C6 2116 A9 2121 D8 3103 A4 3108 C5 3113 C5 3118 C6 3123 B8 3128 D8 3134 D3 5051 D2 5105 A1 6105 C4 6111 B6 7101 B4 7107 E3 F100 A2 F105 B1 I117 A10 I122 B9 A
2051 D2 2101 A2 2106 C3 2112 D5 2117 B9 2122 D8 3104 A4 3109 C5 3114 D5 3119 C6 3124 B10 3129 D7 3135 E10 5052 E1 6101 A4 6106 E4 6112 A8 7102 B6 7108 E4 F101 A2 I113 B6 I118 A10 I123 B9
2052 E1 2102 A3 2107 C5 2113 B7 2118 C9 2124 E10 3105 C3 3110 D4 3115 D5 3120 A6 3125 C7 3130 B9 4101 C6 5101 A3 6102 A5 6107 D5 6113 B8 7103 D4 7110 E9 F102 A3 I114 C6 I119 D7
1 2 3 4 5 6 7 8 9 10
1101
20145
POWER BOARD
B 3 5101 B
N AC ADAPTER SB: 56852x4
9mH
1206 1206 1206

820K 820K 270K
F100
3103 3102 3104

4
PB: 56862
250V
3
2103
4n7
6101 6102 5103 3121 2114

A 2 3101 A
275V
275V
HJC-S1578 +12VCC
2101
2102
100n
220n
GPP20J SCK164L
GPP20J F103 1 10R/1/2W1n /1KV
km/450V
1105
GND 6103 6104 9 I115 2AI116 I117 I118 1 DJ-505
1102
250V
5105 F101
2104
2105
C C
4n7
82u
220K/1/2W
BYD33J 220K/1/2W
GPP20J GPP20J 3 4102 3
1n/1KV
1
1000u/25V
1
2
100MHZ
470u/25V
470u/25V
T2AH
3120
3116
6 HeatSink
2108
L C8B-R6H 250V 6112 2
2EZ10
2115
2116
2120
6115
bead F102 F104 FCH20A15
2
AC INLET Y/G WIRE
6111
3124
5
0R75
3130
8102 F105 7
5R6
1 3123 2117
D 7101TEA1533AP/N1 4 8 D
B 1 8 3106 300V 4R7/1/2W/1%
1n /1KV B
Vcc Drain I122 +3.3V
400V
1u 16 1R /1/2W 5102 2113
2109
2 7 7102
Gnd Hvs STP6NC60FP bead 2n2 I121 I123 2A
I113
820u 10
820u/10V
250V 6113
6 3107
3122
3
2118
2119
0R75
STPS10L45CFP
500V
Ctrl Driver
2111
0R82 /1/2W1% 220p
owner.
10R /1/2W
1K 1%
4 5 3108 3109 I114 4103

2106
3105
22n
E Dem Sense HeatSink E
0R82 /1/2W1%
1%
470R 22K
0R82 /1/2W
2107 4101
3117
3118
3119
HeatSink
C 330n C
6105
6K8 1%
BAV103
/1/2W
3111 3112 3113
3125
3126
820R
8052
46099
36K 1% 220K 33K

F F
4K7 /1206
3127NI
100K1%
1
BAV21
6107
3110
3115
10K
330R1%
3128
TO SCALER BD 1502
7104
2 BRIGHTNESS TCET1103G
3 BL_CTL 7103 I119 2121 I120
BC337-40
D 4 PANEL_ID 39p D
3129 2122
100u/25V
2053
5 PWR_SAVING
22u /50V
3134
2112
47K
K 47K 3n9
G 6 6110 3114 G
6108 50515u R
22K1%
7 +12VCC BZX284-C6V8 4K7
3131
7106
BZX284-C12
SB140 2051 A TL431

6106
BZX284-C15
8 7108
50525u+3.3V 470u 3133
1u 16
2055
6114
9 25 BC848C
2052 68K
10
A
470u
1u 16
2054
E 25 7107 E
H BC848C 7110 H
G
BT169B
3135
100n
2124
510R
STAND FOR CHIP COMPONENTS.
I I
1 2 3 4 5 6 7 8 9 10
CHN TYT12-3215 SETNAME XH3 (HUDSON-150S)

Ref Des NI CLASS_NO 1 --------
3127 212010909104
100K POWER BOARD 1 2002-11-29
J 3138 158 5466 1 2003-01-21J
150S4F/00C
2002-10-11 3
NAMEJACK Hu/YS Tseng SUPERS. 2 130 1 A3
C
1 2 3 4 5 6 7 8 9 10 11 12 13
50 150P4 LCD Schematic Diagram(Power board_B)
1 2 3 4 5 6 7 8 9 10 11 12 13
A A
1 2 3 4 5 6 7 8 9 1801 A9 7804 A5
1802 B9 7805 C5
2801 B1 7806 D8
2802 B2 7807 E7
2803 B2 7808 E8
POWER BOARD 2804 C2 7809 E1
+12V 2805 C2 9801 A1
B SB: 56852x4 2806 C2 B
BZX79-B5V6
BZX79-B5V6
INVERTER 2807 D2
470u/25V
PB: 56862
2808 D2
9801
3819
3821
2816
6802
6803
5K1
5K1
+12V 5801 2811 B4
A 3801 I00076 A
2812 B4
TO PANEL LAMP TO PANEL LAMP

RUE185 1A
+12VCC 7804 2827 1801 2813 C4
Si4532DY 61193 2814 C4
A
7801 1 8 2u2/1206 1 1500Vmax 1 2815 C4
OZ960G S1 D1_1 2828
33p/3KV33p/3KV
2 10 2816 A5
2821 2820
C 2u2/1206 2 2820 A8 C
10p /3KV
2801 2802 2 7
1
CTIMR NDR_B 20 G1 D1_2 3 2821 B8
2822
1u 1u 2822 B8
2811
47n
2 19 3 6 2823 C8
OVP PDR_A S2 D2_1 2824 C8
4 1500Vmax 1
3806NI 2812470p 5 2825 E7
3 18 4 2826 E8
B BL_CTL ENA CT G2 D2_2 5 7 2 B
10p /3KV
10K Active "HIGH" RT 2827 A7
3M /5%
2803 3818
30K 6
3M /5%
2828 A7
3805
3830
3822
2829
4 17
10K
D SST RT 1802 2829 B8 D

470n 61193
3807 3801 A1
+5V 5 16 3802 E1
VDDA PGND
28041u
22R 3803 E6
REF2V5 6 15 8n2
2813 3804 C4
3808NI
1K8 1%
GNDA LCT
100K
2823
3823
3805 B1
18nNI
8n2
+12V 6806
2824
A 100n
2814 BAV99 3806 B1
2805 7 14 6804
owner.
REF DIM 7805 BAV99 3807 B1

7803 100n Si4532DY 3808 C1
3804
E C 2N7002NI 3811 8 13 10K 1 8 C 3809 D1 E
BZX79-C9V1
RT RT1 LPWM 1% S1 D1_1 3810 D3

6801NI
150K 5% 3811 C2
9 12 2815 2 7 FB
6805
360R1%
FB PDR_C G1 D1_2 3813 D2
3824
47n BAV99 3814 E2
2806 3 6 3815 E1
10 11 S2 D2_1
7802NI CMP NDR_D 3816 E1
MMBT3904 LT1 4n7 3817 E2

4 5
2807
3810
NI3809
3818 B4
10K
G2 D2_2 +12V
1n5
3819 A4
100K
F F
3821 A5
3822 B8
3826 NI
D D 3823 C8
3824 C9
5K1
3825 E6
PDTA144EU 3826 D7
REF2V5
2808
3813
3827 E7
100n
7806
1M
3828 E8
G 3829 E8 G
3827
3829
330R
5K1
3830 B8
3816
3828
10K
5801 A7
1K
3802 6808 3814 A 6801 C1
7808 6802 A4
FB 3825 7807 MMBT3904 LT1
E 22K 1N4148 56K 1% BL_CTL E 6803 A4
MMBT3904 LT1
BZX79-B5V6
100K 6804 C7
+5V 6805 C8
6807
2825
2826
3803
470n
6806 C9
120K
3815 3817
1u
H 7809 6807 E8 H
2N7002 PANEL_ID
BRIGHTNESS 10K 390K 6808 E1
1% 7801 A3
7802 D1
STAND FOR CHIP COMPONENTS. 7803 C1
1 2 3 4 5 6 7 8 9
I Ref Des NI I
2824 319801701830
18n
3806 212010909103
10K
3808 319802151040 CHN TYT12-3215 SETNAME XH3 (HUDSON-150S)
100K
3809 319802151040 CLASS_NO 1 --------
100K 1 2003-01-21
3826 232273061512 POWER BOARD
J 5K1 J
6801 319801029180 3138 158 5466
BZX79-C9V1 150S4F/00C
7802 823827706871 2002-10-11 3
MMBT3904LT1
7803 934003470235 NAMEJack Hu/YS Tseng SUPERS. 2 130 2 A3
2N7002
C
1 2 3 4 5 6 7 8 9 10 11 12 13
150P4 LCD 51
Power Board C.B.A.
GRID BOARD GRID BOARD

8052 A3 B
REF LABEL SIDE REF LABEL SIDE
8102 A5 B
____ ___ __ ____ ___ __
9103 A4 B
1101 C5 B 2054 A3 A
9105 A2 B
1102 B5 B 2055 A4 A
9106 A2 B
1105 D5 B 2106 A3 A
9107 A2 B
1801 D5 B 2107 B3 A
9801 C1 B
1802 D1 B 2109 A3 A
9802 C3 B
2051 A2 B 2121 A5 A
9803 D2 B
2052 A1 B 2122 A4 A
9804 D2 B
2053 A3 B 2124 A4 A
9805 D1 B
2101 B5 B 2801 C4 A
9806 D1 B
2102 A5 B 2802 C4 A
9807 C2 B
2103 A4 B 2803 C4 A
9808 D2 B
2104 A4 B 2804 C4 A
9809 C1 B
2105 C4 B 2805 C3 A
9810 C2 B
2108 C3 B 2806 C3 A
9811 C2 B
2111 B3 B 2807 C3 A
9814 C2 B
2112 A3 B 2808 C4 A
9815 C2 B
2113 A2 B 2811 D4 A
9816 C2 B
2114 C2 B 2812 D4 A
2115 B1 B 2813 D3 A
2116 B1 B 2814 D3 A
2117 A1 B 2815 D4 A
2118 B1 B 2823 D2 A
2119 A1 B 2824 D2 A
2120 C5 B 2825 C5 A
2816 D2 B 2826 C5 A
2820 D4 B 2827 D4 A
2821 D4 B 3844 A5 A
2828 D4 A
2822 C4 B 6105 A3 A
3102 A1 A
2829 C4 B 6106 A2 A
3103 A1 A
3101 B4 B 6110 A2 A
3104 A1 A
3106 B3 B 6114 A4 A
3105 A3 A
3107 A3 B 6804 D5 A
3109 B3 A
3108 A3 B 6805 D2 A
3110 A3 A
3116 B3 B 6806 D3 A
3111 A3 A
3117 B3 B 7107 B2 A
3112 A3 A
3118 B3 B 7108 A2 A
3113 A3 A
3119 B4 B 7801 C4 A
3114 A2 A
3120 B3 B 7802 C5 A
3115 A3 A
3121 B2 B 7803 C5 A
3126 A5 A
3122 C3 B 7804 D4 A
3127 A4 A
3123 B2 B 7805 D4 A
3128 A5 A
3124 C4 B 7806 D4 A
3129 A4 A
3125 A2 B 7807 C5 A
3131 A5 A
3130 B1 B 7808 C4 A
3134 A2 A
3133 A3 B 7809 D3 A
3135 A4 A
3801 C1 B 3803 C5 A
3802 C3 B 3804 D3 A
3814 C3 B 3805 C4 A
3815 C3 B 3806 C4 A
3816 C3 B 3807 C4 A
3817 C3 B 3808 C5 A
4101 B3 B 3809 D5 A
4102 B2 B 3810 D3 A
4103 A2 B 3811 D3 A
5051 A2 B 3813 C4 A
5052 A1 B 3818 D4 A
5101 A5 B 3819 D4 A
5102 B3 B 3821 D3 A
5103 B2 B 3822 D5 A
5105 C4 B 3823 D5 A
5801 D4 B 3824 D3 A
6101 B4 B 3825 C5 A
6102 A4 B 3826 C4 A
6103 A4 B 3827 C5 A
6104 A5 B 3828 D4 A
6107 A3 B 3829 D4 A
6108 A2 B 3830 D5 A
6111 B3 B 3841 C3 A
家电维修资料网，免费下载各种维修资料 6112 B2 B 3842 C4 A
3843 A5 A
52 150P4 LCD Scaler Board C.B.A.-1
150P4 LCD 53
Scaler board C.B.A.-2
54 150P4 LCD Component MAP ROM WAVE FORM
GRID BOARD GRID BOARD 2360 B3 B 2478 B4 B 3305 C2 B 3478 D3 B 5443 B4 B 1 7310-3 8 7310-10 15 7310-18 22 7310-27
REF LABEL SIDE REF LABEL SIDE 2361 C3 B 2479 C4 B 3306 B1 B 3479 B3 B 5444 B4 B
____ ___ ____ ____ ___ ___ 2362 C3 B 2480 A3 B 3307 C2 B 3480 D3 B 5445 A3 B
1201 B1 B 1301 B2 B 2363 C3 B 2481 A3 B 3308 B1 B 3481 C4 B 5446 A3 B
1203 C1 B 1412 B4 B 2364 C3 B 2482 A4 B 3309 B1 B 3482 C4 B 5447 B4 B
1305 C3 B 2201 D1 B 2365 C1 B 2483 A3 B 3310 B1 B 3483 C4 B 5448 C4 B
1410 C3 B 2202 D1 B 2366 B2 B 2501 A4 B 3313 C2 B 3484 C4 B 5449 C4 B
1502 A4 B 2203 D1 B 2367 C1 B 2502 A4 B 3314 C2 B 3485 C3 B 5450 C4 B
2505 A3 B 1 V/div AC 1 V/div AC 1 V/div AC 1 V/div AC
1503 A1 B 2205 B1 B 2368 C2 B 3315 B3 B 3486 C3 B 5501 A4 B
2506 A3 B 50 uS/div 50 uS/div 50 uS/div 50 uS/div
2503 A4 B 2206 B1 B 2369 B2 B 3316 B3 B 3487 B4 B 5502 A4 B
2504 A3 B 2507 A3 B
2207 B1 B 2370 B2 B
2508 A3 B
3322 C3 B 3488 C4 B 5503 A3 B 2 7310-4 9 7310-11 16 7310-19 23 7310-28
7311 D3 B 2208 B1 B 2371 B2 B 3324 C3 B 3490 B3 B 5504 A4 B
2209 C1 B 2372 B2 B 2509 A3 B 3325 C3 B 3491 A3 B 5505 A4 B
2210 C1 B 2373 B2 B 2510 A4 B 3327 C3 B 3492 C3 B 5506 A2 B
2211 C1 B 2374 B2 B 2511 A2 B 3328 B3 B 3493 C3 B 6201 C1 B
2212 C1 B 2375 B2 B 2512 A2 B 3329 B3 B 3494 B4 B 6203 D1 B
2213 C1 B 2376 C2 B 2513 A4 B 3330 B2 B 3495 B4 B 6204 D1 B
2216 D2 B 2377 B2 B 2514 A2 B 3331 B2 B 3496 B4 B 6205 D1 B
2217 D2 B 2378 B2 B 2515 A2 B 3332 B2 B 3497 B4 B 6206 C1 B 1 V/div AC 1 V/div AC 1 V/div AC 1 V/div AC
2218 C1 B 2379 C2 B 2516 A2 B 3333 B2 B 3498 B4 B 6207 C1 B
50 uS/div 50 uS/div 50 uS/div 50 uS/div
2219 C1 B 2380 C2 B 2517 A2 B 3335 B2 B 3501 A2 B 6208 D1 B
2221 D1 B 2381 B2 B 2519 A2 B 3336 B2 B 3502 A2 B 6209 D1 B
3 7310-5 10 7310-12 17 7310-20 24 7310-29
2225 B1 B 2382 B2 B 2521 A2 B 3337 B3 B 3503 A2 B 6210 B1 B
2226 D1 B 2383 B2 B 2523 A1 B 3338 B2 B 3504 A2 B 6211 B1 B
2227 B1 B 2384 B3 B 2525 A1 B 3360 D2 B 3505 A1 B 6212 B1 B
2228 D1 B 2385 C2 B 2527 A1 B 3361 D2 B 3506 A1 B 6213 B1 B
2229 B1 B 2386 B1 B 2528 A1 B 3362 D3 B 3507 A1 B 6214 C1 B
2230 D1 B 2387 B2 B 2529 A1 B 3363 D3 B 3508 A1 B 6215 B1 B
2231 C1 B 2388 B2 B 2530 A1 B 3364 D3 B 3509 A1 B 6216 B1 B 1 V/div AC 1 V/div AC 1 V/div AC 1 V/div AC
2232 C1 B 2389 B2 B 2531 A1 B 3365 D2 B 3510 A1 B 6217 B1 B 50 uS/div 50 uS/div 50 uS/div 50 uS/div
2233 D1 B 2390 B2 B 2532 A1 B 3366 D2 B 3511 A3 B 6218 B1 B
2301 B2 B 2391 B3 B 2533 A2 B 3367 D2 B 3513 A2 B 6219 C1 B 4 7310-6 11 7310-13 18 7310-23
2302 B2 B 2392 B3 B 2534 A2 B 3368 D3 B 3514 A4 B 6220 D2 B
2303 D2 B 2393 B3 B 2535 A2 B 3369 D3 B 3515 A1 B 6221 D1 B
2304 B1 B 2394 C3 B 2536 A2 B 3370 D3 B 3516 A1 B 6301 C2 B
2305 C1 B 2395 C3 B 2537 A2 B 3371 D3 B 3517 A1 B 6441 B3 B
2306 A1 B 2396 C2 B 3201 C1 B 3372 D3 B 3518 A1 B 6442 D3 B
2307 B2 B 2397 C2 B 3202 C1 B 3373 D3 B 3519 A2 B 6443 D3 B
2308 B2 B 2398 C2 B 3203 C1 B 3374 D2 B 3520 A2 B 6444 B3 B 1 V/div AC 1 V/div AC
3204 C1 B 1 V/div AC
2309 B2 B 2441 B3 B 3441 B3 B 3521 A2 B 6501 A2 B 50 uS/div 50 uS/div 50 uS/div
2310 A1 B 2442 B3 B 3205 C1 B 3442 B3 B 3522 A2 B 6502 A2 B
2311 C2 B 2443 B3 B 3206 C1 B 3443 B3 B 3523 A2 B 6503 A3 B 5 7310-7 12 7310-14
2312 C2 B 2444 B4 B 3207 C1 B 3444 B4 B 3524 A2 B 6504 A4 B
19 7310-24
2313 C2 B 2445 B4 B 3208 C1 B 3445 B3 B 3525 A2 B 7202 D1 B
2314 B3 B 2446 B4 B 3209 C1 B 3446 C3 B 3526 A2 B 7203 C1 B
2315 B3 B 2447 A4 B 3212 C1 B 3447 C3 B 3527 A1 B 7211 C1 B
2316 C2 B 2448 A4 B 3213 C1 B 3448 B3 B 3528 A1 B 7301 B2 B
2317 C2 B 2449 B4 B 3214 C1 B 3449 B3 B 3529 A4 B 7302 A1 B
2320 D2 B 2450 B4 B 3215 D1 B 3450 B4 B 3530 A3 B 7303 A1 B
3216 D2 B 1 V/div AC 1 V/div AC 1 V/div AC
2321 D3 B 2451 B4 B 3451 B4 B 3531 A3 B 7304 C2 B
3217 D2 B 50 uS/div 50 uS/div 50 uS/div
2330 C3 B 2452 B4 B 3452 A4 B 3532 A2 B 7310 D2 B
2331 C3 B 2453 B3 B 3218 C1 B 3453 D4 B 3533 A2 B 7441 A4 B
2332 B3 B 2454 B4 B 3219 C1 B 3454 C4 B 3534 A2 B 7442 A3 B 6 7310-8 13 7310-15 20 7310-25
2333 B3 B 2455 B4 B 3220 C1 B 3455 D4 B 3535 A2 B 7443 B3 B
2334 B3 B 2456 A3 B 3221 D2 B 3456 D4 B 3536 A2 B 7444 C4 B
2335 B3 B 2457 B4 B 3222 D2 B 3457 D4 B 3537 A2 B 7445 B3 B
2339 C3 B 2458 B3 B 3223 D1 B 3458 D4 B 3538 A2 B 7446 B4 B
2340 C3 B 2459 B3 B 3224 C1 B 3459 C4 B 3539 A2 B 7447 C3 B
2341 C3 B 2460 B4 B 3225 D1 B 3460 D4 B 3540 A2 B 7448 C3 B
2342 C3 B 2461 B4 B 3226 C1 B 3461 D4 B 3541 A2 B 7501 A1 B 1 V/div AC 1 V/div AC
3227 C1 B 3462 C4 B 3542 A2 B
1 V/div AC
2343 C3 B 2462 B4 B 7502 A1 B 50 uS/div 50 uS/div
3228 C1 B 50 uS/div
2344 C3 B 2463 A3 B 3463 A4 B 3543 A2 B 7503 A3 B
2345 C3 B 2464 B4 B 3229 C1 B 3464 B4 B 3544 B3 B 7504 A3 B 7 7310-9 14 7310-17 21 7310-26
2347 C3 B 2465 B4 B 3230 D1 B 3465 A4 B 3545 A4 B 7505 A3 B
2348 C3 B 2466 B4 B 3231 D1 B 3466 B4 B 5201 C1 B 7506 A3 B
2349 C3 B 2467 B4 B 3232 D1 B 3467 A4 B 5202 D1 B 7507 A2 B
2350 C3 B 2468 B4 B 3233 D1 B 3468 A4 B 5301 B3 B 7508 A2 B
2351 C3 B 2469 B4 B 3234 D1 B 3469 A3 B 5303 D2 B 7509 A4 B
2352 C3 B 2470 C4 B 3235 D1 B 3470 A4 B 5304 A1 B 7510 A4 B
2353 C3 B 2471 B3 B 3236 C1 B 3471 A3 B 5305 C1 B 7511 A2 B
3237 D1 B 1 V/div AC 1 V/div AC 1 V/div AC
2354 C3 B 2472 B4 B 3472 B4 B 5306 A1 B 7512 A2 B 50 uS/div 50 uS/div 50 uS/div
2355 B3 B 2473 B3 B 3238 C1 B 3473 B4 B 5310 D2 B 7513 A2 B
2356 B3 B 2474 B4 B 3301 A1 B 3474 B3 B 5311 C3 B 7514 A2 B
2357 B3 B
2358 B3 B
2475
2476
B4
A4
B
B
3302
3303
B3
B3
B
B 家电维修资料网，免费下载各种维修资料
3475
3476
B4
B4
B
B
5312
5441
C3
B3
B
B
2359 B3 B 2477 C4 B 3304 B1 B 3477 B3 B 5442 A4 B
Exploded View 150P4 LCD 55
Go to cover page
1 2 3 4 5 6
1 2 3 1901 B1
1902 A3
A 1903 B3 A
1904 B3
1905 C3
CONTROL PCB 1906 C3
1907 D3
SB: 57321 x12 1908 D3
1909 E3
PB: 57331 6901 B2
6902 E1
B 6903 E1 B
A A F032 B1
F033 C1
F034 C1
F035 C1
1902
Alle rechten voorbehouden. Verveelvuldiging, geheel ofAll rights reserved. Reproduction in whole or in parts
SKHHAJ2410 F036 C1
K_PWR F037 C1
F038 C1
4 2
3 1
F039 C1
6901 F041 D1 C
C L-3WYGW
1903 F042 D1
SKHHAJ2410 F043 D1
3 1 K_RIGHT F044 D1
B G Y B F045 D1
3 1
4 2
K 2
1901 1904
63373
1 LED_G F032 K_LEFTSKHHAJ2410
D D
F033
3 1
4 2
2 LED_R
3 F034
F035 1905
4 SKHHAJ2410
K_UP
C 5 F036 C
owner.
TO SCALER BD 1503
3 1
F037 4 2
6
E F038 E
7 1906
F039 SKHHAJ2410
K_DOWN
8
F041
4 2
3 1
9
10 F042
F043 1907
11 SKHHAJ2410
K_OK
F D 12 F044 D F
4 2
3 1
13 F045
LF_LED2 LF_LED1 1908

SKHHAJ2410
K_AUTO
6902
6903
BLUE
BLUE
4 2
3 1
G G
1909
SKHHAJ2410
K_LF
E E
4 2
3 1
H H
1 2 3
I I
CHN TYT12- SETNAME XH3L (HUDSON3-150P4)

CLASS_NO 1 --------
CONTROL BOARD
J 3138 158 5546 J
150P4CG/00C
2003-01-30 3
NAMEYiku Yu SUPERS. 1 130 1 A4
C
1 2 3 4 5 6
56 150P4 LCD Control board (C.B.A.)
Go to cover page
GRID BOARD GRID BOARD

REF LABEL SIDE REF LABEL SIDE
____ ____ ___ ____ ___ __
1901 A14 B 1901 A4 B
1902 A16 B 1902 A2 B
1903 A8 B 1903 A10 B
1904 A7 B 1904 A11 B
1905 A11 B 1905 A7 B
1906 A10 B 1906 A8 B
1907 A12 B 1907 A6 B
1908 A6 B 1908 A12 B
1909 A1 B 1909 A17 B
6901 A17 B 6901 A1 B
6902 A1 B 6902 A17 B
6903 A2 B 6903 A16 B
Exploded View 150P4 LCD 57
Go to cover page
104
3138 154 05373
VESA COVER(T)
40
3138 157 54331

back cover assy
1045 50
3138 157 54321
3138 158 55461 Compact base
Control Assy
1046
3138 158 54661

POW+inverter Assy
1047
3138 158 54671

Scaler Assy
1076
3138 158 55611

mainframe+wire assy
1071
8238 277 12431
TFT-LCD Mod HSD 150SXA1
30
3138 157 53841
bezel assy
58 150P4 LCD Recommended Parts List
Go to cover page
Model: 150P4CG/00C
Item Code Number Description

30 313815754311 BEZEL ASSY-150P4(T)
40 313815754331 BACK COVER ASSY-150P4(T)
50 313815754321 COMPACT BASE
104 313815405373 VESA COVER(T)
450 313815634501 CARTON-150P4CG
451 313815634851 CUSHION-R-150P4
452 313815634861 CUSHION-L-150P4
453 313815621481 P.E.BAG
601 313811704771 E-D.F.U. ASSY-150P4C
1072 313818876831 FFC50/60/50 61406
1073 3138 16874231 MAINS CORD
1088 313818872732 CORD SUB-D 15/1M8/15 SUB-D(I/F Cable)
1102 242208600266 FUSE 5X20 HT 2A/250V IEC
6112 932214337687 DIO REC FCH20A15(NIEC)L
6113 932219202687 DIO REC STPS10L45CFP(ST00)L
7101 935270037112 TEA1533AP/N1
7102 932215101687 TRANS STP6NC60FP
7103 933179600126 TRA SIG BC337-40
7104 932214014667 PHOTOCOUPLER TCET1103G 4P
7106 933771100686 IC TL431CLPRP 3P
7301 932219321671 IC SM GM5115-BD
7310 932217946682 IC SM M29W010B-90K1
7441 932218206685 IC SM IRU1206-25CY
7442 932219359668 IC SM AME8815AEGT150
7443 823827712981 IC PACIF1X-A
7801 932219312668 IC SM OZ960G
Spare Parts List 150P4 LCD 59
Go to cover page
MODEL : 150P4CG/00C
0030 313815754311 BEZEL ASSY-150P4(T)

0040 313815754331 BACK COVER ASSY-150P4(T)
0050 313815754321 COMPACT BASE(T)
7101 935270037112 IC TEA1533AP/N1 (PHSE) L
0099 122210002083 TAPE S-ADH PET TP 20MMX50MM 3101 212261200061 NTC DC SCK-164 S 16R PM15 B 7103 933179600126 TRA SIG BC337-40 (PHSE) A
0100 313815133061 SHIELDING INVERTER 3102 232271161824 RST SM 1206 RC01 820K PM5 R 7104 932214014667 OPT CP TCET1103(G) (VISH) L
0102 313815160931 CONTACT SPRING-HANNSTAR(S) 3103 232271161824 RST SM 1206 RC01 820K PM5 R 7106 933771100686 IC TL431CLP S (MOTA) R
0104 313815405373 VESA COVER(T) 3104 232271161274 RST SM 1206 RC01 270K PM5 R 7107 933967310685 TRA SIG SM BC848C (ONSE) R
3105 232273461002 RST SM 0805 RC12H 1K PM1 R 7108 933967310685 TRA SIG SM BC848C (ONSE) R
3106 212211000298 RST MFLM MF1/2WS A 1R PM1 A 7110 933826850126 THYRIS BT169B (PHSE) A
Various 3107 212211000315 RST MFLM MF1/2WS A 10R PM1 A 7801 932219312668 IC SM OZ960G (O2MI) R
3108 213810113471 RST CRB CFR-12 A 470R PM5 A 7804 932219473668 FET POW SM SI4532ADY (VISH) R
0300 282206240595 INK CARTRIDGE -EP-T 3109 319802152230 RST SM 0805 22K PM5 COL R 7805 932219473668 FET POW SM SI4532ADY (VISH) R
0450 313815634501 CARTON-150P4CG 3110 319802151030 RST SM 0805 10K PM5 COL R 7806 934044130115 TRA SIG SM PDTA144EU (PHSE) R
0451 313815634851 CUSHION-R-150P4 3111 232273463603 RST SM 0805 RC12H 36K PM1 R 7807 933864360215 TRA SIG SM MMBT3904 (PHSE) R
0452 313815634861 CUSHION-L-150P4 3112 319802152240 RST SM 0805 220K PM5 COL R 7808 933864360215 TRA SIG SM MMBT3904 (PHSE) R
0453 313815621481 P.E.BAG 3113 319802153330 RST SM 0805 33K PM5 COL R
3114 319802154720 RST SM 0805 4K7 PM5 COL R
3115 232271161472 RST SM 1206 RC01 4K7 PM5 R 1047 313815854671
SCALER ASSY-1(HSD)
Accessories 3116 212211000418 RST MFLM MF1/2WS A 220K PM1 A
3117 212211000452 RST MFLM MF1/2WS A 0R82 PM1 A
0291 313815559451 LABEL(HS) 3118 212211000452 RST MFLM MF1/2WS A 0R82 PM1 A
0291 313815559461 LABEL(LG) 3119 212211000452 RST MFLM MF1/2WS A 0R82 PM1 A 2209 223878615649 CER2 0603 X7R 16V 100N PM10 R
0601 313811704771 E-D.F.U. ASSY(150P4C) 3120 212211000418 RST MFLM MF1/2WS A 220K PM1 A 2210 223878615649 CER2 0603 X7R 16V 100N PM10 R
0615 313811705191 HEX CODE OF F/W (HS USE ONLY) 3121 212211000315 RST MFLM MF1/2WS A 10R PM1 A 2211 223886715331 CER1 0603 NP0 50V 330P PM5 R
0616 313811705201 HEX CODE OF F/W(LG USE ONLY) 3122 212010590718 RST MOX 1W RSS A 0R75 PM5 A 2212 223886715331 CER1 0603 NP0 50V 330P PM5 R
1045 313815855461 CONTROL ASSY 3123 212211000311 RST MFLM MF1/2WS A 4R7 PM1 A 2213 223878615649 CER2 0603 X7R 16V 100N PM10 R
1046 313815854661 POW+INVERTER ASSY 3124 212010590718 RST MOX 1W RSS A 0R75 PM5 A 2216 223886715331 CER1 0603 NP0 50V 330P PM5 R
1047 313815854671 SCALER ASSY-1(HSD) 3125 212211000354 RST MFLM MF1/2WS A 820R PM1 A 2217 223886715331 CER1 0603 NP0 50V 330P PM5 R
1071 823827712431 TFT-LCD MOD HSD150SXA1(HSD0) 3126 232273466802 RST SM 0805 RC12H 6K8 PM1 R 2218 223886715339 CER1 0603 NP0 50V 33P PM5 R
1072 313818876831 FFC 50/60/5061406 3128 232273463301 RST SM 0805 RC12H 330R PM1 R 2219 223886715221 CER1 0603 NP0 50V 220P PM5 R
1073 313816874231 MAINS CORD 3129 319802154730 RST SM 0805 47K PM5 COL R 2221 223878615649 CER2 0603 X7R 16V 100N PM10 R
1076 313815855611 FRAME-DUAL+WIRE ASSY 3130 212211000312 RST MFLM MF1/2WS A 5R6 PM1 A 2225 223878615649 CER2 0603 X7R 16V 100N PM10 R
1088 313818872732 CORD SUB-D 15/1M8/15 SUB-D M/M 3131 232273462203 RST SM 0805 RC12H 22K PM1 R 2227 223878615649 CER2 0603 X7R 16V 100N PM10 R
1102 242208600266 FUSE 5X20 HT 2A 250V IEC B 3133 213810113683 RST CRB CFR-12 A 68K PM5 A 2229 223878615649 CER2 0603 X7R 16V 100N PM10 R
3134 319802154730 RST SM 0805 47K PM5 COL R 2233 223878615649 CER2 0603 X7R 16V 100N PM10 R
3135 232273061511 RST SM 0805 RC11 510R PM5 R 2301 223886715478 CER1 0603 NP0 50V 4P7 PM0P25 R
3802 213810113223 RST CRB CFR-12 A 22K PM5 A 2302 223886715478 CER1 0603 NP0 50V 4P7 PM0P25 R
3803 232273061124 RST SM 0805 RC11 120K PM5 R 2303 202001293723 ELCAP SM RV2 16V 47U PM20 R
1046 313815854661 POW+INVERTER ASSY 3804 232273461003 RST SM 0805 RC12H 10K PM1 R 2304 202001293723 ELCAP SM RV2 16V 47U PM20 R
3805 319802151030 RST SM 0805 10K PM5 COL R 2305 202001293723 ELCAP SM RV2 16V 47U PM20 R
3807 319802152290 RST SM 0805 22R PM5 COL R 2306 202001293723 ELCAP SM RV2 16V 47U PM20 R
3813 319802151050 RST SM 0805 1M PM5 COL R 2309 223878615649 CER2 0603 X7R 16V 100N PM10 R
2051 202203100053 ELCAP GL 25V S 470U PM20 A
3814 213811273563 RST CRB CFR-25 A 56K PM5 A 2310 223878615649 CER2 0603 X7R 16V 100N PM10 R
2052 202203100053 ELCAP GL 25V S 470U PM20 A
3817 212211000425 RST MFLM MF1/2WS A 390K PM1 A 2311 223858615623 CER2 0603 X7R 50V 1N PM10 R
2053 203803513304 ELCAP RGA 25V S 100U PM20 A
3818 232273061303 RST SM 0805 RC11 30K PM5 R 2312 223858615623 CER2 0603 X7R 50V 1N PM10 R
2054 222278019763 CER2 0805 Y5V 16V 1U PM20 R
3819 232273061512 RST SM 0805 RC11 5K1 PM5 R 2314 223886715109 CER1 0603 NP0 50V 10P PM5 R
2055 222278019763 CER2 0805 Y5V 16V 1U PM20 R
3821 232273061512 RST SM 0805 RC11 5K1 PM5 R 2316 223878615649 CER2 0603 X7R 16V 100N PM10 R
2101 202233000029 CAP MPP 275V S 100N PM10 B
3822 823827712591 SHIP RESISTOR RZC50 3M 2317 223891615641 CER2 0603 X7R 25V 22N PM10 R
2102 203830100314 CAP MPP 275V S 220N PM10 B
3823 232273461802 RST SM 0805 RC12H 1K8 PM1 R 2320 223878615649 CER2 0603 X7R 16V 100N PM10 R
2103 202055490139 CERSAF NSB 250V S 4N7 PM20 B
3824 232273463601 RST SM 0805 RC 12H 360R PM1 R 2321 223878615649 CER2 0603 X7R 16V 100N PM10 R
2104 202055490139 CERSAF NSB 250V S 4N7 PM20 B
2105 202203100077 ELCAP KM 450V S 82U PM20 B
3827 232273061512 RST SM 0805 RC11 5K1 PM5 R 2353 223858615623 CER2 0603 X7R 50V 1N PM10 R
2106 223858015641 CER2 0805 X7R 50V 22N PM10 R
2107 222291019856 CER2 0805 Y5V 25V 330N P8020 R
3829 319802153310 RST SM 0805 330R PM5 COL R
2108 225260108026 CER2 DC X7R 1KV S 1N PM10 A 2361 223858615623 CER2 0603 X7R 50V 1N PM10 R
3830 823827712591 SHIP RESISTOR RZC50 3M
2109 222278019763 CER2 0805 Y5V 16V 1U PM20 R 2362 223858615623 CER2 0603 X7R 50V 1N PM10 R
2112 203803513506 ELCAP RGA 50V S 22U PM20 A 2363 223858615623 CER2 0603 X7R 50V 1N PM10 R
2113 202055490158 CERSAF CD 250V S 2N2 PM20 B 2364 223858615623 CER2 0603 X7R 50V 1N PM10 R
2114 225260108026 CER2 DC X7R 1KV S 1N PM10 A 2365 223878615649 CER2 0603 X7R 16V 100N PM10 R
2115 202203100132 ELCAP LZ 25V S 1000U PM20 B 2366 223878615649 CER2 0603 X7R 16V 100N PM10 R
2116 202203100132 ELCAP LZ 25V S 1000U PM20 B 2367 223878615649 CER2 0603 X7R 16V 100N PM10 R
2117 225260108026 CER2 DC X7R 1KV S 1N PM10 A 5051 313810874951 CHOKE COIL 5.0UH PM10 2368 223878615649 CER2 0603 X7R 16V 100N PM10 R
2118 202203100134 ELCAP EB 10V S 820U PM20 B 5052 313810874951 CHOKE COIL 5.0UH PM10 2369 223878615649 CER2 0603 X7R 16V 100N PM10 R
2119 202203100134 ELCAP EB 10V S 820U PM20 B 5101 313818870151 LINE FILTER 9MH 2370 223878615649 CER2 0603 X7R 16V 100N PM10 R
2120 202203100068 ELCAP GL 25V S 470U PM20 B 5102 242254942026 IND FXD BEAD EMI 100MHZ 50R A 2371 223878615649 CER2 0603 X7R 16V 100N PM10 R
2121 223886115399 CER1 0805 NP0 50V 39P PM5 R 5103 313818875911 POWER TRANSFORMER (EFD25) 2372 223878615649 CER2 0603 X7R 16V 100N PM10 R
2122 223858015631 CER2 0805 X7R 50V 3N9 PM10 R 5105 313816874511 FERRITE BEAD 2373 223878615649 CER2 0603 X7R 16V 100N PM10 R
2124 223891015649 CER2 0805 X7R 25V 100N PM10 R 5801 313818875921 TRANSFORMER I00076 2374 223878615649 CER2 0603 X7R 16V 100N PM10 R
2803 223878019858 CER2 0805 Y5V 16V 470N P8020 R 2377 223878615649 CER2 0603 X7R 16V 100N PM10 R
2805 223891015649 CER2 0805 X7R 25V 100N PM10 R 2379 223878615649 CER2 0603 X7R 16V 100N PM10 R
6101 932217441682 DIO REC GPP20J (GI00) B 2380 223878615649 CER2 0603 X7R 16V 100N PM10 R
2806 223858015632 CER2 0805 X7R 50V 4N7 PM10 R
2807 223858015625 CER2 0805 X7R 50V 1N5 PM10 R
2808 222258015649 CER2 0805 X7R 50V 100N PM10 R
2811 223858015645 CER2 0805 X7R 50V 47N PM10 R
6105 933952580685 DIO SIG SM BAV103 (VISH) R 2384 223878615649 CER2 0603 X7R 16V 100N PM10 R
2812 223886115471 CER1 0805 NP0 50V 470P PM5 R
6106 934038700115 DIO REG SM BZX284-C12 (PHSE) R 2385 223878615649 CER2 0603 X7R 16V 100N PM10 R
2813 223858015635 CER2 0805 X7R 50V 8N2 PM10 R
6107 319801010070 DIO SIG BAV21 (COL) A 2386 223878615649 CER2 0603 X7R 16V 100N PM10 R
2814 222258015649 CER2 0805 X7R 50V 100N PM10 R
6108 933957760673 DIO REC SB140 A (GI00) A 2387 223878615649 CER2 0603 X7R 16V 100N PM10 R
2815 223858015645 CER2 0805 X7R 50V 47N PM10 R
6110 934038640115 DIO REG SM BZX284-C6V8 (PHSE)R 2388 223878615649 CER2 0603 X7R 16V 100N PM10 R
2816 202203100068 ELCAP GL 25V S 470U PM20 B
6111 933723420133 DIO REC BYD33J A (PHSE) A 2389 223878615649 CER2 0603 X7R 16V 100N PM10 R
2820 823827712601 HV CERAMIC CAP 33P/3KV
6114 934038720115 DIO REG SM BZX284-C15 (PHSE) R 2390 223878615649 CER2 0603 X7R 16V 100N PM10 R
6115 932219207683 DIO REC 2EZ10 A (PAJI) R 2391 223878615649 CER2 0603 X7R 16V 100N PM10 R
6802 319801055680 DIO REG BZX79-B5V6 A COL A 2392 223878615649 CER2 0603 X7R 16V 100N PM10 R
2823 223858015635 CER2 0805 X7R 50V 8N2 PM10 R
6803 319801055680 DIO REG BZX79-B5V6 A COL A 2393 223878615649 CER2 0603 X7R 16V 100N PM10 R
2825 222278019763 CER2 0805 Y5V 16V 1U PM20 R
6804 319801010620 DIO SIG SM BAV99 (COL) R
2826 223878019858 CER2 0805 Y5V 16V 470N P8020 R 2394 223878615649 CER2 0603 X7R 16V 100N PM10 R
2827 222278119867 CER2 1206 Y5V 16V 2U2 P8020 R 2395 223878615649 CER2 0603 X7R 16V 100N PM10 R
2828 222278119867 CER2 1206 Y5V 16V 2U2 P8020 R 2396 223878615649 CER2 0603 X7R 16V 100N PM10 R
6807 319801055680 DIO REG BZX79-B5V6 A COL A
2829 823827712611 HV CERAMIC CAP 10P/3KV 2397 223878615649 CER2 0603 X7R 16V 100N PM10 R
6808 319801010010 DIO SIG 1N4148 (COL) A
2398 223878615649 CER2 0603 X7R 16V 100N PM10 R
60 150P4 LCD Spare Parts List
Go to cover page
2441 202001293721 ELCAP SM RV2 16V 10U PM20 R 5201 313816874261 TI321611G800-SMD
2442 223878615649 CER2 0603 X7R 16V 100N PM10 R 3316 319802131510 RST SM 0603 150R PM5 COL 5202 313816874261 TI321611G800-SMD
2443 223878615649 CER2 0603 X7R 16V 100N PM10 R 3322 235003510479 RST NETW SM ARV24 4X 47R PM5 R 5301 242254944195 IND FXD 0805 EMI 100MHZ 220R R
2444 223878615649 CER2 0603 X7R 16V 100N PM10 R 3324 235003510479 RST NETW SM ARV24 4X 47R PM5 R 5303 313816874261 TI321611G800-SMD
2447 202001293721 ELCAP SM RV2 16V 10U PM20 R 3328 235003510479 RST NETW SM ARV24 4X 47R PM5 R 5306 313816874261 TI321611G800-SMD
2452 202001293721 ELCAP SM RV2 16V 10U PM20 R 3338 319802131090 RST SM 0603 10R PM5 COL 5443 313816874261 TI321611G800-SMD
2453 223878615649 CER2 0603 X7R 16V 100N PM10 R 3360 319802131030 RST SM 0603 10K PM5 COL 5445 313816874261 TI321611G800-SMD
2456 202001293721 ELCAP SM RV2 16V 10U PM20 R 3365 319802131030 RST SM 0603 10K PM5 COL 5449 313816874261 TI321611G800-SMD
2459 223878615649 CER2 0603 X7R 16V 100N PM10 R 3368 319802134720 RST SM 0603 4K7 PM5 COL 5502 242254944195 IND FXD 0805 EMI 100MHZ 220R R
2460 223878615649 CER2 0603 X7R 16V 100N PM10 R 3370 319802134720 RST SM 0603 4K7 PM5 COL 5503 313816874261 TI321611G800-SMD
2461 223878615649 CER2 0603 X7R 16V 100N PM10 R 3371 319802131030 RST SM 0603 10K PM5 COL 5504 242254944195 IND FXD 0805 EMI 100MHZ 220R R
2462 223878615649 CER2 0603 X7R 16V 100N PM10 R 3372 319802131010 RST SM 0603 100R PM5 COL 5505 242254944195 IND FXD 0805 EMI 100MHZ 220R R
2463 202001293721 ELCAP SM RV2 16V 10U PM20 R 3373 319802131010 RST SM 0603 100R PM5 COL 5506 242254944195 IND FXD 0805 EMI 100MHZ 220R R
2464 223878615649 CER2 0603 X7R 16V 100N PM10 R 3374 319802131030 RST SM 0603 10K PM5 COL
2465 223878615649 CER2 0603 X7R 16V 100N PM10 R 3441 319802134790 RST SM 0603 47R PM5 COL
2473 202001293721 ELCAP SM RV2 16V 10U PM20 R 3444 319802134790 RST SM 0603 47R PM5 COL 6220 932217973668 DIO REC SM BAT42W (PAJI) R
2475 223878615649 CER2 0603 X7R 16V 100N PM10 R 3445 319802131010 RST SM 0603 100R PM5 COL 6221 933913910115 DIO SIG SM BAS32L (PHSE) R
2476 223878615649 CER2 0603 X7R 16V 100N PM10 R 3446 319802131010 RST SM 0603 100R PM5 COL 6441 933913910115 DIO SIG SM BAS32L (PHSE) R
2477 202001293721 ELCAP SM RV2 16V 10U PM20 R 3447 319802131010 RST SM 0603 100R PM5 COL 6442 319801010620 DIO SIG SM BAV99 (COL) R
2478 202001293721 ELCAP SM RV2 16V 10U PM20 R 3448 319802131090 RST SM 0603 10R PM5 COL 6443 319801010620 DIO SIG SM BAV99 (COL) R
2479 202001293782 ELCAP SM RV2 25V 10U PM20 R 3449 319802131030 RST SM 0603 10K PM5 COL 6503 933913910115 DIO SIG SM BAS32L (PHSE) R
2482 202001293721 ELCAP SM RV2 16V 10U PM20 R 3451 319802131040 RST SM 0603 100K PM5 COL 6504 933913910115 DIO SIG SM BAS32L (PHSE) R
2483 202001293721 ELCAP SM RV2 16V 10U PM20 R 3452 319802131020 RST SM 0603 1K PM5 COL
2503 202203100068 ELCAP GL 25V S 470U PM20 B 3455 319802131030 RST SM 0603 10K PM5 COL
2504 202203100068 ELCAP GL 25V S 470U PM20 B 3458 319802131030 RST SM 0603 10K PM5 COL
2506 223878615649 CER2 0603 X7R 16V 100N PM10 R 3464 232270463901 RST SM 0603 RC22H 390R PM1 R 7202 932214526668 IC SM M24C02-WMN6 (ST00) R
2507 223858615636 CER2 0603 X7R 50V 10N PM10 R 3465 319802190030 RST SM 0603 JUMP. 0R05 COL 7203 932214526668 IC SM M24C02-WMN6 (ST00) R
2508 202001293725 ELCAP SM RV2 35V 4U7 PM20 R 3466 232270461622 RST SM 0603 RC22H 1K62 PM1 R 7211 935260739118 IC SM 74LVC14APW (PHSE) R
2509 223858615636 CER2 0603 X7R 50V 10N PM10 R 3467 319802190030 RST SM 0603 JUMP. 0R05 COL 7301 932219321671 IC SM GM5115-BD (GEMI) Y
2510 202001293725 ELCAP SM RV2 35V 4U7 PM20 R 3468 319802131030 RST SM 0603 10K PM5 COL 7302 932218206685 IC SM IRU1206-25CY (INR0) R
2514 223878615649 CER2 0603 X7R 16V 100N PM10 R 3469 319802131030 RST SM 0603 10K PM5 COL 7303 932218206685 IC SM IRU1206-25CY (INR0) R
2515 223858615623 CER2 0603 X7R 50V 1N PM10 R 3471 319802131230 RST SM 0603 12K PM5 COL 7304 935270954115 IC SM SA56616-28D (PHSE) R
2516 223878615649 CER2 0603 X7R 16V 100N PM10 R 3472 319802131030 RST SM 0603 10K PM5 COL 7310 932217946682 IC SM M29W010B-90K1 (ST00) L
2517 223858615623 CER2 0603 X7R 50V 1N PM10 R 3474 319802131030 RST SM 0603 10K PM5 COL 7311 932214725682 IC M24C16-WBN6 (ST00) L
2519 223858615623 CER2 0603 X7R 50V 1N PM10 R 3476 319802131030 RST SM 0603 10K PM5 COL 7441 932218206685 IC SM IRU1206-25CY (INR0) R
2521 223858615623 CER2 0603 X7R 50V 1N PM10 R 3477 319802131090 RST SM 0603 10R PM5 COL 7442 932219359668 IC SM AME8815AEGT150 (AME0) R
3478 319802132210 RST SM 0603 220R PM5 COL 7443 823827712981 IC PACIFIC1X-A
3479 319802131030 RST SM 0603 10K PM5 COL 7446 933967380685 TRA SIG SM BC858C (ONSE) R
3480 319802132210 RST SM 0603 220R PM5 COL 7447 932215686685 FET SIG SM 2N7002L (ONSE) R
3482 232271161478 RST SM 1206 RC01 4R7 PM5 R 7448 932215686685 FET SIG SM 2N7002L (ONSE) R
3483 232271161478 RST SM 1206 RC01 4R7 PM5 R 7501 933967380685 TRA SIG SM BC858C (ONSE) R
3202 319802131030 RST SM 0603 10K PM5 COL 3484 232271161478 RST SM 1206 RC01 4R7 PM5 R 7502 933967380685 TRA SIG SM BC858C (ONSE) R
3203 319802131030 RST SM 0603 10K PM5 COL 3485 319802133320 RST SM 0603 3K3 PM5 COL 7503 932209265685 TRA SIG SM MUN2211J (ONSE) R
3204 319802131010 RST SM 0603 100R PM5 COL 3486 319802133320 RST SM 0603 3K3 PM5 COL 7504 932216638668 FET POW SM SI5441DC (VISH) R
3205 319802131010 RST SM 0603 100R PM5 COL 3487 232271191032 RST SM 1206 JUMP. MAX 0R05 R 7505 932209265685 TRA SIG SM MUN2211J (ONSE) R
3206 319802131010 RST SM 0603 100R PM5 COL 3488 232271161478 RST SM 1206 RC01 4R7 PM5 R 7506 932216638668 FET POW SM SI5441DC (VISH) R
3207 319802131010 RST SM 0603 100R PM5 COL 3494 319802131090 RST SM 0603 10R PM5 COL 7507 933967380685 TRA SIG SM BC858C (ONSE) R
3208 319802131090 RST SM 0603 10R PM5 COL 3495 319802190030 RST SM 0603 JUMP. 0R05 COL 7508 933967380685 TRA SIG SM BC858C (ONSE) R
3209 319802134730 RST SM 0603 47K PM5 COL 3496 319802190030 RST SM 0603 JUMP. 0R05 COL 7509 932209265685 TRA SIG SM MUN2211J (ONSE) R
3212 319802131010 RST SM 0603 100R PM5 COL 3497 319802131090 RST SM 0603 10R PM5 COL 7510 932216638668 FET POW SM SI5441DC (VISH) R
3213 319802131030 RST SM 0603 10K PM5 COL 3501 319802131010 RST SM 0603 100R PM5 COL 7511 932209265685 TRA SIG SM MUN2211J (ONSE) R
3216 319802131010 RST SM 0603 100R PM5 COL 3502 319802131010 RST SM 0603 100R PM5 COL 7512 933967380685 TRA SIG SM BC858C (ONSE) R
3217 319802131010 RST SM 0603 100R PM5 COL 3503 319802131010 RST SM 0603 100R PM5 COL 7513 932209265685 TRA SIG SM MUN2211J (ONSE) R
3221 319802131030 RST SM 0603 10K PM5 COL 3504 319802131010 RST SM 0603 100R PM5 COL 7514 933967380685 TRA SIG SM BC858C (ONSE) R
3222 319802131030 RST SM 0603 10K PM5 COL 3505 319802131010 RST SM 0603 100R PM5 COL
3223 319802131010 RST SM 0603 100R PM5 COL 3506 319802131010 RST SM 0603 100R PM5 COL
3227 319802132220 RST SM 0603 2K2 PM5 COL 3510 232271191032 RST SM 1206 JUMP. MAX 0R05 R
3228 319802132220 RST SM 0603 2K2 PM5 COL 3511 319802131030 RST SM 0603 10K PM5 COL
1045 313815855461 Control ASSY
3229 319802134730 RST SM 0603 47K PM5 COL 3514 319802131040 RST SM 0603 100K PM5 COL
3231 319802131090 RST SM 0603 10R PM5 COL 3517 319802131030 RST SM 0603 10K PM5 COL
3233 232273467509 RST SM 0805 RC12H 75R PM1 R 3519 319802131030 RST SM 0603 10K PM5 COL
3521 319802131030 RST SM 0603 10K PM5 COL 6901 932214603682 LED VS L-3WYGW (KIEL) B
3235 232273467509 RST SM 0805 RC12H 75R PM1 R
3522 319802131030 RST SM 0603 10K PM5 COL 6902 932219383682 LED VS L-934MBD (KIEL) B
3236 319802131010 RST SM 0603 100R PM5 COL
3525 319802131030 RST SM 0603 10K PM5 COL 6903 932219383682 LED VS L-934MBD (KIEL) B
3237 232273467509 RST SM 0805 RC12H 75R PM1 R
3305 319802131090 RST SM 0603 10R PM5 COL
3308 319802131010 RST SM 0603 100R PM5 COL
3309 319802131010 RST SM 0603 100R PM5 COL
3310 319802131010 RST SM 0603 100R PM5 COL
3313 319802131030 RST SM 0603 10K PM5 COL
3314 319802131030 RST SM 0603 10K PM5 COL
GENERAL PRODUCT SPECIFICATION 150P4 LCD 61
Go to cover page
PHILIPS 150P4
GENERAL PRODUCT
SPECIFICATION
. ANALOG AND DIGITAL SIGNAL INPUT
. AUTO PICTURE ADJUSTMENT
. 1410 FACTORY PRESET MODES AND 14 USER MODES WHICH CAN BE

RECOVERED TO PRESET MODES
. USER FRIENDLY OSD DISPLAY FOR MODE IDENTIFICATION

/ADJUSTMENT
. LIGHT FRAME FEATURES
. PIXEL DEFECT OF PANEL
. DDC2B COMMUNICATION CAPABILITY
. MAX. RESOLUTION 1024 x 768 NON-INTERLACED AT 75 HZ
. 15 COLOR TFT LCD FLAT PANEL
. EASY TILT & COMPACT BASE
. FULL RANGE POWER SUPPLY 90 264 VAC
. CE ENVIRONMENTAL POLICY
. ANTI-GLARE TO REDUCE LIGHT REFLECTION
. POWER MANAGEMENT CAPABILITY
. SOG SYNC SUPPORT
. TCO 99
. PROTECTIVE COVER (Option)
15"TFT XGA LCD CMTR

TYPE : 150P4CG/00C 8639 000 14135
BRAND : PHILIPS
2003-01-30
YiKuan YU 19 590 1
2003-01-30
62 150P4 LCD
GENERAL PRODUCT SPECIFICATION
Go to cover page
CONTENTS
1.0 Foreword
2.0 Product profile

2.1 LCD
2.2 Scanning frequencies
2.3 Video dot rate
2.4 Power input
2.5 Power consumption
2.6 Dimensions
2.7 Weight
2.8 Functions
2.9 Ambient temperature
2.10 Safety and EMI requirements
3.0 Electrical characteristics

3.1 3.1 Interface signals
3.1.1 Video
3.1.2 Interface cable
3.1.3 Software control functions via OSD/control
3.2 OSD function control
3.3 Timing requirement
3.3.1 Mode storing capacity
3.3.2 Factory preset timings
3.3.3 Horizontal scanning
3.3.4 Vertical scanning
3.4 Power input connection
3.5 Power management
3.6 Display identification
4.0 Visual characteristics

4.1 Test conditions
4.2 Resolution
4.3 Brightness
4.4 Image size
4.4.1 Actual display size
4.5 Brightness uniformity
4.6 White color adjustment
4.7 Light Frame features
4.8 Monitors pixel defect
15"TFT XGA LCD CMTR

TYPE : 150P4CG/00C 8639 000 14135
BRAND : PHILIPS
2003-01-30
YiKuan YU 19 590 2
2003-01-30
Go to cover page
5.0 Mechanical characteristics

5.1 Controls
5.2 Unit dimension / weight
5.3 Tilt and swivel base
5.4 Transportation packages
5.4.1 Shipping dimension / weight
5.4.2 Block unit / palletization
6.0 Environmental characteristics

6.1 Susceptibility of display to external environment
6.2 Transportation tests
6.3 Display disturbances from external environment
6.4 Display disturbances to external environment
6.4.1 EMI
7.0 Reliability
7.1 Mean time between failures
8.0 Quality assurance requirements

8.1 Acceptance test
9.0 Serviceability
15"TFT XGA LCD CMTR

TYPE : 150P4CG/00C 8639 000 14135
BRAND : PHILIPS
2003-01-30
YiKuan YU 19 590 3
2003-01-30
64 150P4 LCD
Go to cover page
1.0 FOREWORD
This specification describes a 15 XGA multi-scan color TFT
LCD monitor with maximum resolution up to 1024x768/75Hz non-interlaced.
2.0 PRODUCT PROFILE

HUDSON 15 TFT LCD flat panel monitor
Analog & Digital interface
Integrated tilt and compact base
2.1 LCD
Type NR. : LG panel LS150X05-A3
Dimensions : 326.0(H)*254.0(V)*11.5(D) mm
Pitch ( mm ) : 0.297 x 0.297 mm
Color pixel arrangement : RGB stripe arrangement
Display surface : Antiglare with hard coating(3H)
Number of color : 6 bits, 16,777,216 colors
Backlight : CCFL edge-light system
Active area(W x H) : 304.1 x 228.1mm (15.0 Diagonal)
Viewing angle(CR 10) : Vertical 9095 degree, Horizontal 120115 degree typical.
Contrast ratio : 350 typical.
Luminance of white : 250200 Nits typical
Type NR. : HannStar panel HSD150SXA1-A

Dimensions : 321.0(H)*249.0(V)*10.2(D) mm
Pitch ( mm ) : 0.297 x 0.297 mm
Color pixel arrangement : RGB stripe arrangement
Display surface : Anti-glare with hard coating(3H)
Number of color : 6 bits, 16,777,216 colors
Backlight : CCFL edge-light system
Active area(W x H) : 304.1 x 228.1mm (15.0 Diagonal)
Viewing angle(CR 10) : Vertical 10595 degree, Horizontal 130115 degree typical.
Contrast ratio : 400 typical. .
Luminance of white : 250 Nits typical
2.2 Scanning frequencies Hor.: 30 61KHz

Ver.: 56 76 Hz
2.3 Video dot rate : <79 MHz
2.4 Power input : 90 264 Vac, 50/60 3 Hz
2.5 Power consumption : < 2327 W typ.(with audio), (19W without audio)
: AC input power < 1W at 230V
< 1W at 120V when DC switch is off.
2.6 Dimensions : 386W 343W x 310H x 170180D (Incl. Pedestal)
2.7 Weight : 3.7Kg
15"TFT XGA LCD CMTR

TYPE : 150P4CG/00C 8639 000 14135
BRAND : PHILIPS
2003-01-30
YiKuan YU 19 590 4
2003-01-30
GENERAL PRODUCT SPECIFICATION 150S4 LCD 65
Go to cover page
3.2 OSD (On Screen Display) function

Adjustable functions:
MAIN CONTROLS
LANGUAGE
ADJUST POSITION
BRIGHTNESS & CONTRAST
VIDEO NOISE
ADJUST COLOR
OSD SETTINGS
PRODUCT INFORMATION
RESET TO FACTORY SETTINGS
INPUT SELECTION
EXIT MAIN CONTROLS

MOVE SELECTION THEN ok
LANGUAGE: ENGLISH, ESPANOL, FRANCAIS, DEUTSCH, ITALIANO, S.CHINESE
ADJUST POSITION: HORIZONTAL

VERTICAL
BRIGHTNESS & CONTRAST: Brightness and Contrast adjustment.
VIDEO NOISE: Phase adjustment, Clock adjustment

ADJUST COLOR: Original panel color, 9300K for general use,
6500k for image management,
User red green blue adjustable
OSD POSITION: OSD H-position, OSD V-position
PRODUCT INFORMATION: show the product information
RESET TO FACTORY SETTING: recall to Factory preset settings.
15"TFT XGA LCD CMTR

TYPE : 150S4FG/00C 8639 000 13701
BRAND : PHILIPS
2002-10-28
H.P.WU 20 590 7
2002-10-28
66 150P4 LCD
Go to cover page
3.1 Interface signals
3.1.1 Video
Input signal: Video, H-sync, V-sync

Video: 0.7 Vp-p, input impedance, 75 ohm
Sync. : Separate sync TTL level. Input impedance 2k2 ohm
Hor. Sync Positive/Negative
Ver. Sync Positive/Negative
DVI : One channel TMDS signal
3.1.2 Interface Cable
D-Sub Cable pin assignment:
PIN No. SIGNAL

1 Red
2 Green/SOG
3 Blue
4 Sense (GND)
5 Test (GND)
6 Red GND
7 Green GND
8 Blue GND
9 +5V
10 Sync GND
11 Sense (GND)
12 Serial data (SDA)
13 H/H+V sync
14 V-sync
15 Data clock (SCL)
DVI Cable Pin assignment:

Pin No. Description
1 TMDS data2-
2 TMDS data2+
3 TMDS data2 shield
4 NC
5 NC
6 DDC clock
7 DDC data
8 NC
9 TMDS data1-
10 TMDS data1+
11 TMDS data1 shield
12 NC
15"TFT XGA LCD CMTR

TYPE : 150P4CG/00C 8639 000 14135
BRAND : PHILIPS
2003-01-30
YiKuan YU 19 590 6
2003-01-30
Go to cover page
13 NC
14 +5V
15 Ground (return for +5V and H/V sync)
16 Hot plug detect
17 TMDS data0-
18 TMDS data0+
19 TMDS data0 shield
20 NC
21 NC
22 TMDS clock shield
23 TMDS clock+
24 TMDS clock-
3.2 OSD (On Screen Display) function

Adjustable functions:
MAIN CONTROLS
LANGUAGE
ADJUST POSITION
BRIGHTNESS & CONTRAST
VIDEO NOISE
ADJUST COLOR
OSD SETTINGS
PRODUCT INFORMATION
RESET TO FACTORY SETTINGS
INPUT SELECTION
EXIT MAIN CONTROLS

MOVE SELECTION THEN ok
LANGUAGE: ENGLISH, ESPANOL, FRANCAIS,

DEUTSCH, ITALIANO, S.CHINESE
ADJUST POSITION: HORIZONTAL

VERTICAL
15"TFT XGA LCD CMTR

TYPE : 150P4CG/00C 8639 000 14135
BRAND : PHILIPS
2003-01-30
YiKuan YU 19 590 7
2003-01-30
68 150P4 LCD
Go to cover page
VIDEO NOISE: Phase adjustment, Clock adjustment
ADJUST COLOR: Original panel color,

9300K for general use,
6500k for image management,
sRGB
User red green blue adjustable
OSD POSITION: OSD H-position, OSD V-position

PRODUCT INFORMATION: show the product information
RESET TO FACTORY SETTING: recallreturn to Factory preset timings and settings.
INPUT SELECTION: Analog

Digital
3.3 Timing requirement
3.3.1 Mode storing capacity
(1) Factory preset modes : 140

(2) User modes : 14
3.3.2 Factory preset timings
MODE NO. 1 2 3 4
RESOLUTION 640 x 350 720 x 400 640 x 480 640x480
Dot clock (MHz) 25.175 28.321 25.175 30.240
fh 31.469kHz 31.469kHz 31.469kHz 35.0kHz

A ( us ) 31.78(800 dots) 31.78(900dots) 31.778 (800 dots) 28.571(864 dots)
B ( us ) 3.813(96 dots) 3.813(108dots) 3.813( 96 dots) 2.116( 64 dots)
C ( us ) 1.907(48 dots) 1.907(54dots) 1.907 ( 48 dots) 3.175( 96 dots)
D ( us ) 25.42(640 dots) 25.42(720dots) 25.422(640 dots) 21.164(640 dots)
E ( us ) 0.636(16 dots) 0.636(18dots) 0.636 (16 Dots) 2.116(64 Dots)
fv 70Hz(70.09) 70Hz(70.087) 60Hz ( 59.940 ) 66.7 Hz( 66.667 )
O (ms ) 14.27(449 lines) 14.27(449 lines) 16.683 (525 Lines )15.000(525 lines )
P ( ms ) 0.064(2 lines) 0.064(2 lines) 0.064 ( 2 lines ) 0.086( 3 lines )
Q (ms ) 1.907 ( 60 lines) 1.112 (35 lines) 1.049 ( 33 lines ) 1.14( 39 lines )
R ( ms ) 11.12(350 lines) 12.71(400 lines) 15.25 3 (480Lines) 13.714(480 lines )
S ( ms ) 1.179 (3 7 lines) 0.384 (12 lines) 0.317 (10 lines) 0.086( 3 lines )
SYNC. H/V +/- -/+ -/- +/+
POLARITY Or -/-
SEP . SYNC Y Y Y Y
15"TFT XGA LCD CMTR

TYPE : 150P4CG/00C 8639 000 14135
BRAND : PHILIPS
2003-01-30
YiKuan YU 19 590 8
2003-01-30
Go to cover page
A : H-Total O : V-Total
B : H- Sync width P : V- Sync width
C : H- Back porch Q :.V- Back porch
D : H- Video width R : V- Video width
E : H- Front porch S :.V- Front porch
MODE NO. 5 6 7 8
RESOLUTION 640 x 480 640 x 480 800 x 600 800 x 600
Dot clock(MHz) 31.500 31.500 36.000 40.000
fh 37.861kHz 37.500kHz 35.156kHz 37.879kHz

A ( us ) 26.413(832 dots) 26.667 (840 dots) 28.44 (1024 dots) 26.40 (1056 dots)
B ( us ) 1.270(40 dots) 2.032 ( 64 dots) 2.000 ( 72 dots) 3.200 ( 128 dots)
C ( us ) 4.064(128 dots) 3.810 ( 120 dots) 3.556 ( 128 dots) 2.200 ( 88 dots)
D ( us ) 20.317(640 dots) 20.317 ( 640 dots) 22.22 ( 800 dots) 20.00 ( 800 dots)
E ( us ) 0.762(24 dots) 0.508 ( 16 dots) 0.667 ( 24 dots) 1.000 ( 40 dots)
fv 72.809Hz 75Hz (75 ) 56Hz (56.25 ) 60Hz ( 60.316)

O (ms ) 13.735(520 lines) 13.333 (500 lines) 17.78 (625 lines) 16.58 (628 lines)
P ( ms ) 0.079(3 lines) 0.080 ( 3 lines) 0.057 ( 2 lines) 0.106 ( 4 lines)
Q (ms ) 0.739(28 lines) 0.427 ( 16 lines) 0.626 ( 22 lines) 0.607 ( 23 lines)
R ( ms ) 12.678(480 lines) 12.80 (480 lines) 17.07 (600 lines) 15.84 (600 lines)
S ( ms ) 0.237(9 lines) 0.027 ( 1 line ) 0.028 ( 1 line ) 0.026 ( 1 line )
SYNC. H/V -/- -/- +/+ +/+
POLARITY
SEP . SYNC Y Y Y Y
MODE NO. 9 10 11 12
RESOLUTION 800 x 600 800 x 600 832 x 624 1024 x 768
Dot clock(MHz) 50.000 49.500 57.280 65.000
fh 48.077kHz 46.875kHz 49.722kHz 48.363kHz

A ( us ) 20.80 (1040dots) 21.333 (1056dots) 20.11 (1152dots) 20.677(1344 dots)
B ( us ) 2.400 ( 120 dots) 1.616 ( 80 dots) 1.117 ( 64 dots) 2.092(136 dots)
C ( us ) 1.280 ( 64 dots) 3.232 ( 160 dots) 3.911 ( 224 dots) 2.462(160 dots)
D ( us ) 16.00 ( 800 dots) 16.162 ( 800 dots) 14.52 ( 832 dots) 15.754(1024 dots)
E ( us ) 1.120 ( 56 dots) 0.323 ( 16 dots) 0.559 ( 32 dots) 0.369(24 dots)
fv 72Hz ( 72.188) 75Hz ( 75.000) 75Hz ( 74.546) 60.004Hz

O (ms ) 13.85 (666 lines) 13.333 (625lines) 13.41 (667 lines) 16.666(806 lines)
P ( ms ) 0.125 ( 6 lines) 0.064 ( 3 lines) 0.060 ( 3 lines) 0.124(6 lines)
Q (ms ) 0.478 ( 23 lines) 0.448 ( 21 lines) 0.784 ( 39 lines) 0.600(29 lines)
R ( ms ) 12.48 (600 lines) 12.80 (600lines) 12.55 (624 lines) 15.880(768 lines)
S ( ms ) 0.770 ( 37 line ) 0.021 ( 1 line ) 0.020 ( 1 lines) 0.062(3 lines)
SYNC. H/V +/+ +/+ -/- -/-
POLARITY
SEP . SYNC Y Y Y Y
15"TFT XGA LCD CMTR

TYPE : 150P4CG/00C 8639 000 14135
BRAND : PHILIPS
2003-01-30
YiKuan YU 19 590 9
2003-01-30
70 150P4 LCD
Go to cover page
MODE NO. 13 14
RESOLUTION 1024 x 768 1024 x 768
Dot clock(MHz) 75.000 78.750
fh 56.476kHz 60.023kHz
A ( us ) 17.707(1328 dots) 16.66 (1312dots)
B ( us ) 1.813(136 dots) 1.219 ( 96 dots)
C ( us ) 1.920(144 dots) 2.235 ( 176 dots)
D ( us ) 13.653(1024 dots) 13.003 (1024dots)
E ( us ) 0.320(24 dots) 0.203 ( 16 dots)
fv 70.069Hz 75Hz ( 75.029)

O (ms ) 14.272(806 lines) 13.328 (800 lines)
P ( ms ) 0.106(6 lines) 0.050 ( 3 lines)
Q (ms ) 0.513(29 lines) 0.466 ( 28 lines)
R ( ms ) 13.599(768 lines) 12.795 (768 lines)
S ( ms ) 0.053(3 lines) 0.017 ( 1 line )
SYNC. H/V -/- +/+
POLARITY
SEP . SYNC Y Y
3.3.3 Horizontal scanning

Sync polarity : Positive or Negative
Scanning frequency : 30 - 61 KHz
3.3.4 Vertical scanning

Sync polarity : Positive or Negative
Scanning frequency : 56 - 76 Hz
3.4 Power input connection

Power cord length : 1.8 M
Power cord type : 3 leads power cord with protective earth
plug.
3.5 Power management

The power consumption and the status indication of the set
with power management function are as follows,
STATUS Horizontal Vertical Power Spec LED

On Pulse Pulse as normal on Green
Off No Pulse No Pulse < 1W Amber
3.6 Display identification
In accordance with DVI requirement, use DDC2B and EDID 3.0 structure
1.3.
15"TFT XGA LCD CMTR

TYPE : 150P4CG/00C 8639 000 14135
BRAND : PHILIPS
2003-01-30
YiKuan YU 19 590 10
2003-01-30
Go to cover page
4.0 Visual characteristics
4.1 Test conditions
Unless otherwise specified, this specification is defined

under the following conditions.
(1) Input signal : As defined in 3.3, 1024 x 768/75Hz mode (60.023

KHz)
Signal sources must have 75 ohms output
impedance.
(2) Luminance setting: Set contrast to 50 % and brightness to100 % with

full white pattern.
(3) Warm-up: more than 30 minutes after power on with signal supplied.
(4) Ambient light: 400 -- 600 lux.
(5) Ambient temperature: 25 5 °C
4.2 Resolution
Factory preset modes (14 modes)
Mode Resolution H. freq. / V. freq Standard

1. 640 x 350 31.469Khz/70.087Hz VGA
2. 720 x 400 31.469Khz/70.087Hz VGA
3. 640 x 480 31.469Khz/59.940Hz VGA
5. 640 x 480 37.861Khz/72.809Hz VESA
6. 640 x 480 37.500Khz/75.000Hz VESA
7. 800 x 600 35.156Khz/56.250Hz VESA
8. 800 x 600 37.879Khz/60.317Hz VESA
9. 800 x 600 48.077Khz/72.188Hz VESA
10. 800 x 600 46.875Khz/75.000Hz VESA
12. 1024 x 768 48.363Khz/60.004Hz VESA
13. 1024 x 768 56.476Khz/70.069Hz VESA
14. 1024 x 768 60.023Khz/75.029Hz VESA
15"TFT XGA LCD CMTR

TYPE : 150P4CG/00C 8639 000 14135
BRAND : PHILIPS
2003-01-30
YiKuan YU 19 590 11
2003-01-30
72 150P4 LCD
Go to cover page
4.3 Brightness: 250 nits (typ.) at maximum contrast and maximum

brightness
(At center of the screen, Fig. 1)
4.4 Image size

4.4.1 Actual display size
304.1 x 228.1mm
4.5 Brightness uniformity
Set contrast at 50% and turn the brightness to get above 200 nits.
at original panel color of center of the screen
Apply the Fig 1, it should comply with the following formula:
Minimum (B1, B2,.., B5)

> 75 %
Maximum (B1, B2,.., B5)
4.6 White color adjustment
There are Three factory preset white color 9300K and 6500K and sRGB.
Apply full white pattern, with brightness in 100 % position

and the contrast control at 50 %.
The 1931 CIE Chromaticity (color triangle) diagram (x, y)
coordinate for the screen center should be:
9300K CIE coordinates X = 0.283 0.020

Y = 0.297 0.020
6500K CIE coordinates X = 0.313 0.020

Y = 0.329 0.020
sRGB CIE coordinates X = 0.313 0.020

Y = 0.329 0.020
The brightness and contrast setting will be fixed due to sRGB enable.
The sRGB functional will be hidden while running Light Frame features.
4.7 Light Frame features
4.7.1 There is full screen mode and access by HOT-KEY at front of plane.
4.7.2 There are multi-window mode and access by Light Frame application
program
Brightness control
15"TFT XGA LCD CMTR

TYPE : 150P4CG/00C 8639 000 14135
BRAND : PHILIPS
2003-01-30
YiKuan YU 19 590 12
2003-01-30
Go to cover page
4.8 Monitors pixel defect
Philips Flat Panel Monitors Pixel Defect Policy
BRIGHT DOT DEFECTS ACCEPTABLE LEVEL

MODEL 150P 150B 150S
1 lit sub-pixel 0 0 8 or fewer
2 adjacent lit sub-pixels 0 0 3 or fewer
3 adjacent lit sub-pixels (one white pixel) 0 0 1 or fewer
Distance between two bright dot defects* 0 0 15mm or
more
Bright dot defects within 20 mm circle 0 0 3 or fewer
Total bright dot defects of all type 0 0 8 or fewer
BLACK DOT DEFECTS ACCEPTABLE LEVEL

1 dark sub-pixel 4 or fewer 4 or fewer 8 or fewer
2 adjacent dark sub-pixels 1 or fewer 1 or fewer 3 or fewer
3 adjacent dark sub-pixels (one white 0 0 1 or fewer
pixel)
Distance between two black dot defects* 15mm or 15mm or 15mm or
more more more
Black dot defects within 20 mm circle* 3 or fewer 3 or fewer 3 or fewer
Total black dot defects of all type 4 or fewer 4 or fewer 8 or fewer
TOTAL DOT DEFECTS ACCEPTABLE LEVEL

Total bright or black dot defects of all 4 or fewer 4 or fewer 10 or
type fewer
* 1 or 2 adjacent sub-pixel defects = 1 dot defect
15"TFT XGA LCD CMTR

TYPE : 150P4CG/00C 8639 000 14135
BRAND : PHILIPS
2003-01-30
YiKuan YU 19 590 13
2003-01-30
74 150P4 LCD
Go to cover page
5.0 Mechanical characteristics
5.1 Controls
Front: - DC power switch

-OSD function key
- Auto key
- Light Frame hot key
Rear: -Video signal cable D-sub

-Video signal cable DVI/D
-Power cord socket
- 12V audio power outlet
5.2 Unit dimension / Weight
Set dimension (incl. pedestal): 343W x 367H x 218D
Net weight: 3.6 Kg
5.3 Tilt and foldable base
Tilt angle: -5 ° to +25 °
Foldable angle: 90°
5.4 Transportation packages
5.4.1 Shipping dimension/Weight
Carton dimension: 401W x 393H x 158D
Gross weight: 5.1Kg
5.4.2 Block unit / Palletization
layers/block sets/layer sets/block unit

13 6 78
15"TFT XGA LCD CMTR

TYPE : 150P4CG/00C 8639 000 14135
BRAND : PHILIPS
2003-01-30
YiKuan YU 19 590 14
2003-01-30
Go to cover page
6.0 Environmental characteristics

The following sections define the interference and
susceptibility condition limits that might occur
between external environment and the display device.
6.1 Susceptibility of display to external environment

Operating
- Temperature : 5 to 40 degree C
- Humidity : 20% ~ 80%
- Altitude : 0-12,000 feet
- Air pressure : 600-1100 mBAR
Storage
- Temperature : -20 to 60 degree C
- Humidity : 5% ~ 95% ( < 40 )
- Altitude : 0-30,000 feet
- Air pressure : 300-1100 mBAR
Note: recommend at 5 to 35°C, Humidity less than 60 %
6.2 Transportation tests
Standard Philips UAN-D1400 NSTA

Height 76.0 cm 76.0 cm
1 corner 1 corner
Drop Sequence 3 faces 3 edge
Test (-10deg C x 16 hrs) (Room temp) 6 face
Electrical function ok
Test Mechanical function ok
Result No serious damage on set appearance
(Room temp -10 C, humidity 70 %)
(1) PACKAGING
Sequence 5-200 Hz, 0.73 G, 30 min. for Each axis
(2) OPERATING
Vibration 10-50-10 Hz, 0.35 mm, 30 min. for Each axis
Test Test Electrical function ok
Result Mechanical function ok
No serious damage on set appearance
For design evaluationonly
Operating
10 G, 11 msec, 1000 cycles
Bump Temperature : 23 C
Test Humidity : 60 %
Air pressure : 100 kpa
(According to DSD draft standard UAN-D636)
15"TFT XGA LCD CMTR

TYPE : 150P4CG/00C 8639 000 14135
BRAND : PHILIPS
2003-01-30
YiKuan YU 19 590 15
2003-01-30
76 150P4 LCD
Go to cover page
6.3 Display disturbances from external environment

According to IEC 61000-4-2 for ESD disturbances
6.4 Display disturbances to external environment
6.4.1 EMI
EMI: FCC, IC, VCCI, CE, C-Tick, MPRII, BSMI, CCC (China)
7.0 Reliability
7.1 Mean time between failures (MTBF)

System MTBF (Excluding the LCD panel and CCFL): 50,000 hrs
CCFL MTBF: 30,000 hrs
8.0 Quality assurance requirements
8.1 Acceptance test

According to MIL-STD-105D Control II level
AQL : 0.65 (major)

1.5 (minor)
(Please also refer to annual quality agreement)
9.0 Serviceability
The serviceability of this monitor should fulfill the
requirements which are prescribed in UAW-0346 and must
be checked with the check list UAT-0361.
15"TFT XGA LCD CMTR

TYPE : 150P4CG/00C 8639 000 14135
BRAND : PHILIPS
2003-01-30
YiKuan YU 19 590 16
2003-01-30
Go to cover page
Fig 1: Brightness and Uniformity
1/4
1/4
1 2
4 5
Average: 5 points average
15"TFT XGA LCD CMTR

TYPE : 150P4CG/00C 8639 000 14135
BRAND : PHILIPS
2003-01-30
YiKuan YU 19 590 17
2003-01-30
78 150P4 LCD
Go to cover page
SEPARATE SYNC.
VIDEO
C D E
HORIZONTAL
B
A
VIDEO
Q R S
VERTICAL
P
O
COMPOSITE SYNC.
VIDEO
C D E
HORIZONTAL
B
A
FIG-2 TIMING CHART -1
15"TFT XGA LCD CMTR

TYPE : 150P4CG/00C 8639 000 14135
BRAND : PHILIPS
2003-01-30
YiKuan YU 19 590 18
2003-01-30
Go to cover page
VIDEO
Q R S
VERTICAL
P
O
FIG-3 TIMING CHART -2
15"TFT XGA LCD CMTR

TYPE : 150P4CG/00C 8639 000 14135
BRAND : PHILIPS
2003-01-30
YiKuan YU 19 590 19
2003-01-30
98 150P4 LCD Appendix-for different Parts List
Go to cover page
863900014135(150P4CG/00C) 863900014136(150P4AG/00C)
0111 313818875821 MULTMEDIA AUDIO MODULE(AG3P41)
0126 313815558331 ING LABEL 313815559261 RATING LABEL
0601 313811704771 .F.U. ASSY(150P4C) 313811705041 E-D.F.U. ASSY(150P4A)
0450 313815634501 TON-150P4CG 313815634901 CARTON-150P4AG
0451 313815634851 HION-R-150P4 313815635161 CUSHION-R-150P4A
0452 313815634861 HION-L-150P4 313815635171 CUSHION-L-150P4A
0141 313815521641 CK SETUP GUIDE(150P4C) 313815521791 QUICK SETUP GUIDE(150P4A)

Service Manual Philips LCD Monitor 150P4 PDF

Uploaded by

Copyright:

Available Formats

Service Manual Philips LCD Monitor 150P4 PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Service Manual Philips LCD Monitor 150P4 PDF

Uploaded by

Copyright:

Available Formats

http://www.jdwxzlw.com/?

REFER TO BACK COVER FOR IMPORTANT SAFETY GUIDELINES

Proper service and repair is important to the safe, reliable

Under no circumstances should the original design be

Resolution and Preset Modes

Automatic Power Saving

Power Management Definition

VESA's mode POWER LED

OFF Blanked No Yes <1W Amber

This monitor is Environmental Protection Agency (EPA) Energy Star

ENERGY STAR is a U.S. registered mark. AS AN ENERGY STAR

Factory preset mode:

Mode Resol H. freq. / V. freq Standard

Meanwhile, it also reverse 14 sets data space available for user

Front View Note:

UP and DOWN buttons are used when adjusting the OSD of

BRIGHTNESS hotkey. When the UP and DOWN arrow buttons

OK button which when pressed will take you to the OSD

POWER button switches your monitor on.

Automatically adjust the horizontal position,

LightFrame TM hotkey for mode-switching between

Installation Locations Accessory Pack

Correct handling of the monitor

5) VGA Signal Cable

6) E-DFU package with Quick Setup Guide, Using Your Monitor

7) Pivot CD-ROM (optional)

Auto adjustment hotkey

Step 1 : Click on the Start button (Win95, Win98 or Win NT)

Step 7 : Press or to adjust CLOCK. The picture will be jitter as

Step 8 : Press or to adjust PHASE. The picture will be jitter as

Step 9 : Quit OSD menu by press button to save the settings.

To Lock/Unlock OSD function

OSD MAIN MENU LOCKED

OSD MAIN MENU UNLOCK NO VIDEO INPUT

Switch ON/OFF attention signals Fig.1

ATTENTION SIGNAL OFF

The OSD Tree

Digital signal input:

NO VIDEO INPUT WAIT FOR AUTOMATIC ADJUSTMENT

CANNOT DISPLAY THIS VIDEO MODE..

CANNOT DISPLAY THIS VIDEO CHECK CABLE CONNECTION

ENTERING SLEEP MODE

ENTERING SLEEP MODE

TROUBLESHOOTING Horizontal flicker Push the Auto button.

No Picture Make sure the Power cable is plugged to the

No Picture Make sure the computer is turned on.

An after-image This is characteristic of liquid crystal and is

Green, red, The remaining dots are normal

Display position Push the AUTO button.

Image vibrates Check that the signal cable is properly

Vertical flicker Push the AUTO button.

Quick reference for failure mode of LCD panel

This page presents problems that could be made by LCD panel. It is

Failure description Phenomenon

Vertical block defect

Vertical dim lines

Vertical lines defect

Concentric circle formed

Horizontal block defect