Professional Documents
Culture Documents
Xenon Power Supply
Xenon Power Supply
180-Watt Systems
300-watt systems
400-watt systems
WARNINGS The supplied MHC Ballast is a UNIVERSAL BALLAST and must be pre-set for the
unit into which it will be installed.
WARNING !
Incorrect settings of the amperage jumpers PRIOR to the unit being powered on
for the first time after installation may result in lamp damage and/or lamp
explosion; therefore, all power-on operations must be performed with the COVER
ON and operators are to wear eye protection when installing and testing the
ballast.
Replacement units will be shipped pre-set and tested; the above warnings serve as
an additional check prior to field installation.
The installer assumes all responsibility for confirming correct installation per these
instructions and ensuring the device is conformant to all original specifications and
safety regulations.
Work on the unit from the REAR for ease of reference in this instruction.
A directional guide will be given with each picture.
REAR
LIT 208 SUNOPTIC TECHNOLOGIES® Rev.C
(English) Date of Revision:09/02/15
Page 3 of 15
MUST BE PRINTED IN COLOR
Detach the (3) flag connectors from the left rear corner of the ballast shown in the
yellow box below:
REAR
Detach the (2) Molex connectors to the right of the flag connectors shown in the
yellow box below:
REAR
LIT 208 SUNOPTIC TECHNOLOGIES® Rev.C
(English) Date of Revision:09/02/15
Page 4 of 15
MUST BE PRINTED IN COLOR
Unscrew the (4) screws holding the ballast in the unit from the bottom as shown
in the red circles below : Save these screws to attach the new ballast.
REAR
Unscrew the (2) screws from the back side of the ballast that hold on the high
voltage white wires shown in the red boxes below:
REAR
LIT 208 SUNOPTIC TECHNOLOGIES® Rev.C
(English) Date of Revision:09/02/15
Page 5 of 15
MUST BE PRINTED IN COLOR
Unscrew the (4) screws from the corners of the top of the ballast.
Remove the high voltage white wires from the lamp shown in the red boxes
below:
Save the nuts and washers used to attach the white wires.
REAR
REAR
Strip approximately a quarter inch of sheathing off each wire.
On the new ballast, locate and remove the new 2-pin connector shown in the
yellow box below:
REAR
Using the provided quick-connects shown above, connect these wires to the
black and red wires in the case.
The black and red wires can go in either of the (2) quick-connect holes as long as
the black wires are together and the red wires are together.
REAR
Cut the red and black wires directly below the smaller Molex connector coming
from the right of the unitas shown in the red box below:
REAR
LIT 208 SUNOPTIC TECHNOLOGIES® Rev.C
(English) Date of Revision:09/02/15
Page 8 of 15
MUST BE PRINTED IN COLOR
On the new ballast, locate and remove the new 6-pin connector shown in the
yellow box below:
Using the provided quick-connects shown above, connect these wires to the
black and red wires in the case.
The black and red wires can go in either of the (2) quick-connect holes as long as
the black wires are together and the red wires are together.
REAR
LIT 208 SUNOPTIC TECHNOLOGIES® Rev.C
(English) Date of Revision:09/02/15
Page 9 of 15
MUST BE PRINTED IN COLOR
Use the provided cable ties to hold the quick-connects in the rear of the unit as
shown in the yellow boxes below: This is important for proper EMI control.
Cut the excess cable tie.
Use a cable tie and a cable tie anchor to secure the 6-pin Molex connector wires
and route the wires as shown here and in the yellow box below:
Use the front (left) edge of the lamp housing as a guide for placing the anchor.
REAR
Screw in the (4) screws in the bottom of the unit that hold the ballast plate.
REAR
Attach the provided “short” high voltage white wire to the front (left) lamp
connection. Connection hardware order should be: brass nut, white wire, brass
washer, lock washer, brass nut. Be sure not to over tighten which may crack the
insulation block.
Attach the new “long” high voltage white wire to the rear (right) lamp connection.
Connection hardware order should be: brass nut, white wire, brass washer, lock
washer, brass nut.
CAUTION: Be sure not to over tighten which may crack the insulation
block.
REAR
Place the new ballast onto the ballast plate.
Attach the long 6-pin connector at the front right corner of the ballast as shown in
the yellow box below:
Ensure that the black and red wires are to the left of the lamp housing as shown.
REAR
Attach the (3) flag connectors to the leads on the bottom of the ballast in the left
rear corneras shown in the yellow box below:
From left to right, the wires should be: blue to neutral (N), green to ground (tree),
brown to line (L).
REAR
Attach the small 2-pin connector to the leads at the top of the ballast in the left
rear corner as shown in the yellow box below:
REAR
Use one of the extra cable ties provided to secure this 2-pin connector to the 2-
pin lead.
Attach the “short” white wire from the front lamp connection to the right ballast
connection.
Attach the “long” white wire from the rear lamp connection to the left ballast
connection.
REAR
Reinstall the lamp.
Ensure both the front and rear power switches are in the OFF position.
The unit should be emitting light and the rear fan should be running.
If not, turn both power switches back to the OFF position, remove the power cord,
remove the top cover, and ensure all of the wiring is as shown in these
instructions.
END OF INSTRUCTIONS