Configure Basic Router Settings - 42518061

REKAYASA JARINGAN KOMPUTER
“Configure Basic Router Settings”
OLEH :
EDGARD ALEXANDER T.
42518061
2C TKJ
JURUSAN TEKNIK ELEKTRO

PRODI D-4 TEKNIK KOMPUTER DAN JARINGAN
POLITEKNIK NEGERI UJUNG PANDANG
2019-2020
 2013 - 2020 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 1 of 15 www.netacad.com
Lab - Configure Basic Router Settings

Topology
Addressing Table
Device Interface IP Address / Prefix Default Gateway
R1 G0/0/0 192.168.0.1 /24 N/A
R1 G0/0/0
2001:db8:acad::1 /64 N/A
R1 G0/0/0
fe80::1 N/A
R1
G0/0/1 192.168.1.1 /24 N/A
R1 G0/0/1
2001:db8:acad:1::1 /64 N/A
R1 G0/0/1
fe80::1 N/A
R1
Loopback0 10.0.0.1 /24 N/A
R1 Loopback0
2001:db8:acad:2::1 /64 N/A
R1 Loopback0
fe80::1 N/A
PC-A NIC 192.168.1.10 /24 192.168.1.1
PC-A NIC
2001:db8:acad:1::10 /64 fe80::1
PC-B NIC 192.168.0.10 /24 192.168.0.1
PC-B NIC
2001:db8:acad::10 /64 fe80::1
Objectives
Part 1: Set Up the Topology and Initialize Devices
 Cable equipment to match the network topology.
 Initialize and restart the router and switch.
Part 2: Configure Devices and Verify Connectivity
 Assign static IPv4 and IPv6 information to the PC interfaces.
 Configure basic router settings.
 Configure the router for SSH.
 Verify network connectivity.
Part 3: Display Router Information
 Retrieve hardware and software information from the router.
 Interpret the output from the startup configuration.

 Interpret the output from the routing table.
 Verify the status of the interfaces.
Background / Scenario
This is a comprehensive lab to review previously covered IOS router commands. In Parts 1 and 2, you will
cable the equipment and complete basic configurations and interface settings on the router.
In Part 3, you will use SSH to connect to the router remotely and utilize the IOS commands to retrieve
information from the device to answer questions about the router.
For review purposes, this lab provides the commands necessary for specific router configurations.
Note: The routers used with CCNA hands-on labs are Cisco 4221 with Cisco IOS XE Release 16.9.4
(universalk9 image). The switches used in the labs are Cisco Catalyst 2960s with Cisco IOS Release 15.2(2)
(lanbasek9 image). Other routers, switches, and Cisco IOS versions can be used. Depending on the model
and Cisco IOS version, the commands available and the output produced might vary from what is shown in
the labs. Refer to the Router Interface Summary Table at the end of the lab for the correct interface identifiers.
Note: Make sure that the router and switch have been erased and have no startup configurations. Consult
with your instructor for the procedure to initialize and reload a router and switch.
Required Resources
 1 Router (Cisco 4221 with Cisco IOS XE Release 16.9.4 universal image or comparable)
 1 Switch (Cisco 2960 with Cisco IOS Release 15.2(2) lanbasek9 image or comparable)
 2 PCs (Windows with a terminal emulation program, such as Tera Term)
 Console cables to configure the Cisco IOS devices via the console ports
 Ethernet cables as shown in the topology
Note: The Gigabit Ethernet interfaces on Cisco 4221 routers are autosensing and an Ethernet straight-
through cable may be used between the router and PC-B. If using another model Cisco router, it may be
necessary to use an Ethernet crossover cable.
Instructions
Part 1: Set Up the Topology and Initialize Devices

Step 1: Cable the network as shown in the topology.
a. Attach the devices as shown in the topology diagram, and cable as necessary.
b. Power on all the devices in the topology.
Step 2: Initialize and reload the router and switch.
Part 2: Configure Devices and Verify Connectivity

Step 1: Configure the PC interfaces.
a. Configure the IP address, subnet mask, and default gateway settings on PC-A.
b. Configure the IP address, subnet mask, and default gateway settings on PC-B.
Step 2: Configure the router.

Open configuration window
a. Console into the router and enable privileged EXEC mode.
b. Enter configuration mode.
c. Assign a device name to the router.
d. Set the router’s domain name as ccna-lab.com.
e. Disable DNS lookup to prevent the router from attempting to translate incorrectly entered commands as
though they were host names.
f. Encrypt the plaintext passwords.
g. Configure the system to require a minimum 12-character password.
h. Configure the username SSHadmin with an encrypted password of 55Hadm!n2020.
i. Generate a set of crypto keys with a 1024 bit modulus
j. Assign the privileged EXEC password to $cisco!PRIV*
k. Assign $cisco!!CON* as the console password, configure sessions to disconnect after four minutes of
inactivity, and enable login.
l. Assign $cisco!!VTY* as the vty password, configure the vty lines to accept SSH connections only,
configure sessions to disconnect after four minutes of inactivity, and enable login using the local
database.
m. Create a banner that warns anyone accessing the device that unauthorized access is prohibited.
n. Enable IPv6 Routing
o. Configure all three interfaces on the router with the IPv4 and IPv6 addressing information from the
addressing table above. Configure all three interfaces with descriptions. Activate all three interfaces.
p. The router should not allow vty logins for two minutes if three failed login attempts occur within 60
seconds.
q. Set the clock on the router.
r. Save the running configuration to the startup configuration file.
Question:
What would be the result of reloading the router prior to completing the copy running-config startup-
config command?
Jawab : Isi dari running configuration akan terhapus. Pada lab ini, router tidak akan memiliki startup
configuration, setelah reboot, pengguna akan ditanya jika apakah mereka mau atau ingin memasukakan
dialog konfigurasi awal.
your answers hereClose configuration window
Step 3: Verify network connectivity.

a. Using the command line at PC-A, ping the IPv4 and IPv6 addresses for PC-B.
Note: It may be necessary to disable the PCs firewall.
Question:
Were the pings successful? Jawab : Aman.

Type your answers here.
b. Remotely access R1 from PC-A using the Tera Term SSH client.
Using Tera Term on PC-A, open an SSH session to the R1 Loopback interface IPv4 address. Ensure that
the SSH radio button is selected and then click OK to connect to the router. Log in as SSHadmin with the
password 55Hadm!n2020.
Question:
Was remote access successful? Jawab : Aman.

Using Tera Term on PC-A, open an SSH session to the R1 Loopback interface IPv6 address. Ensure that
the SSH radio button is selected and then click OK to connect to the router. Log in as SSHadmin with the
password 55Hadm!n2020. Note: The IPv6 address should be surrounded with square brackets, i.e. [IPv6
address]
Questions:
Was remote access successful? Jawab : Aman.

Why is the Telnet protocol considered to be a security risk?
Jawab : Pada sesi telnet dapat dilihat dalam text yang jelas. Tidak terenkripsi, dan password dengan
mudah dapa dilihat menggunakan paket sniffer.
Part 3: Display Router Information

In Part 3, you will use show commands from an SSH session to retrieve information from the router.
Step 1: Establish an SSH session to R1.

Using Tera Term on PC-B, open an SSH session to the R1 Loopback interface IPv6 address and log in as
SSHadmin with the password 55Hadm!n2020.
Step 2: Retrieve important hardware and software information.

a. Use the show version command to answer questions about the router.
Questions:
What is the name of the IOS image that the router is running?
Jawab : ssr4300-universal_k9.03.16.05.S.155-3.SS-ext.SPA.bin
How much non-volatile random-access memory (NVRAM) does the router have?
Jawab : Keluaran pada perintah show version pada router yakni terdapat 32768 Kb
How much Flash memory does the router have?
Jawab : 322355Kb
b. The show commands often provide multiple screens of outputs. Filtering the output allows a user to
display certain sections of the output. To enable the filtering command, enter a pipe (|) character after a
show command, followed by a filtering parameter and a filtering expression. You can match the output to
the filtering statement by using the include keyword to display all lines from the output that contain the
filtering expression. Filter the show version command, using show version | include register to answer
the following question.
What is the boot process for the router on the next reload?
Jawab : Kebanyakan kasus (0x2102), router akan memproses boot dengan normal, memuat IOS dari
memori flash dan memuat tampilan awal konfigurasi dari NVRAM jika ada. Jika konfigurasi register
adalah 0x2102, router akan melewati konfigurasi startup dan mulai di cmd dalam mode pengguna. Jika
boot awal gagal router masuk ke ROMMON.
Step 3: Display the startup configuration.

Use the show startup-config command on the router to answer the following questions.
How are passwords presented in the output?

Jawab : Perintah Password-encryption membuat sandi menjadi dienskripsi. pada line con memiliki
password dari ciscoconpass dienkripsi sebagai 08654F471A1A0A565328232A60, pada line vty password
dari ciscovtypass dienkripsi menjadi 08654F471A1A0A56533D383D60.
Use the show startup-config | section vty command.
What is the result of using this command?

Jawab : Pengguna akan menerima outpur dari tampilan awal konfigurasi awal dengan baris yang
menyertakan contoh pertama dari ekspresi peyaringan atau filtering expression.
Step 4: Display the routing table on the router.

Use the show ip route command on the router to answer the following questions.
Questions:
What code is used in the routing table to indicate a directly connected network?
Jawab : C merupakan subnert yang terhubung langsung atau directly connected sedangkan L yaitu tampilan
local. Keduanya benar.
How many route entries are coded with a C code in the routing table? Jawab : 3
Step 5: Display a summary list of the interfaces on the router.

a. Use the show ip interface brief command on the router to answer the following question
.
Question:
What command changed the status of the Gigabit Ethernet ports from administratively down to up?
Jawab : No Shutdown.
b. Use the show ipv6 int brief command to verify IPv6 settings on R1.
Question:
What is the meaning of the [up/up] part of the output?

Jawab : Maksudnya pada layer satu dan kedua memiliki status sebagai interface dan tidak tergantung
pada layer 3.
c. On PC-B, change its configuration so that it no longer has a static IPv6 address. You may have to reboot
the machine. Then, issue the ipconfig command on PC-B to examine the IPv6 configuration.
Questions:
What is the IPv6 address assigned to PC-B?

Jawab : IPv6 Address adalah 2001:db8:acad::10/64 atau juga dapat FE80::260:5CFF:FE9B:7913
What is the default gateway assigned to PC-B? Jawab : fe80::1
Issue a ping from PC-B to the R1 default gateway link local address. Was it successful? Jawab : Aman.
Issue a ping from PC-B to the R1 IPv6 unicast address 2001:db8:acad::1. Was it successful?
Jawab : Aman
Reflection Questions
1. In researching a network connectivity issue, a technician suspects that an interface was not enabled. What
show command could the technician use to troubleshoot this issue?
Jawab : menggunakan perintah show ip interface brief atau show startup-config yang akan menampilkan
informasinya.
2. In researching a network connectivity issue, a technician suspects that an interface was assigned an incorrect
subnet mask. What show command could the technician use to troubleshoot this issue?
Jawab : Dengan perintah show startup-config atau show running-config.
Router Interface Summary Table

Router Model Ethernet Interface #1 Ethernet Interface #2 Serial Interface #1 Serial Interface #2
Fast Ethernet 0/0 Fast Ethernet 0/1

1800 (F0/0) (F0/1) Serial 0/0/0 (S0/0/0) Serial 0/0/1 (S0/0/1)
Gigabit Ethernet 0/0 Gigabit Ethernet 0/1
1900 (G0/0) (G0/1) Serial 0/0/0 (S0/0/0) Serial 0/0/1 (S0/0/1)
Gigabit Ethernet 0/0 Gigabit Ethernet 0/1
2900 (G0/0) (G0/1) Serial 0/0/0 (S0/0/0) Serial 0/0/1 (S0/0/1)
Gigabit Ethernet 0/0/0 Gigabit Ethernet 0/0/1
4221 (G0/0/0) (G0/0/1) Serial 0/1/0 (S0/1/0) Serial 0/1/1 (S0/1/1)
Gigabit Ethernet 0/0/0 Gigabit Ethernet 0/0/1
4300 (G0/0/0) (G0/0/1) Serial 0/1/0 (S0/1/0) Serial 0/1/1 (S0/1/1)
Note: To find out how the router is configured, look at the interfaces to identify the type of router and how many
interfaces the router has. There is no way to effectively list all the combinations of configurations for each router
class. This table includes identifiers for the possible combinations of Ethernet and Serial interfaces in the device.
The table does not include any other type of interface, even though a specific router may contain one. An
example of this might be an ISDN BRI interface. The string in parenthesis is the legal abbreviation that can be
used in Cisco IOS commands to represent the interface.
End of document

Configure Basic Router Settings - 42518061

Uploaded by

Copyright:

Available Formats

Configure Basic Router Settings - 42518061

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Configure Basic Router Settings - 42518061

Uploaded by

Copyright:

Available Formats

REKAYASA JARINGAN KOMPUTER

“Configure Basic Router Settings”

JURUSAN TEKNIK ELEKTRO

Lab - Configure Basic Router Settings

R1 G0/0/0 192.168.0.1 /24 N/A

PC-A NIC 192.168.1.10 /24 192.168.1.1

 Interpret the output from the startup configuration.

Part 1: Set Up the Topology and Initialize Devices

Step 2: Initialize and reload the router and switch.

Part 2: Configure Devices and Verify Connectivity

Step 2: Configure the router.

a. Console into the router and enable privileged EXEC mode.

b. Enter configuration mode.

c. Assign a device name to the router.

d. Set the router’s domain name as ccna-lab.com.

f. Encrypt the plaintext passwords.

g. Configure the system to require a minimum 12-character password.

h. Configure the username SSHadmin with an encrypted password of 55Hadm!n2020.

i. Generate a set of crypto keys with a 1024 bit modulus

j. Assign the privileged EXEC password to $cisco!PRIV*

n. Enable IPv6 Routing

q. Set the clock on the router.

r. Save the running configuration to the startup configuration file.

Step 3: Verify network connectivity.

Were the pings successful? Jawab : Aman.

Was remote access successful? Jawab : Aman.

Was remote access successful? Jawab : Aman.

Part 3: Display Router Information

Step 1: Establish an SSH session to R1.

Step 2: Retrieve important hardware and software information.

Step 3: Display the startup configuration.

How are passwords presented in the output?

What is the result of using this command?

Step 4: Display the routing table on the router.

Step 5: Display a summary list of the interfaces on the router.

What is the meaning of the [up/up] part of the output?

What is the IPv6 address assigned to PC-B?

Router Interface Summary Table

Fast Ethernet 0/0 Fast Ethernet 0/1

You might also like