Codigos 275

TRACTORS
Service Bulletin
MACHINE: TJ275, TJ325, TJ375, TJ425, TJ450, and TJ500 Tractors
SUBJECT: Fault Codes for 2005 Production TJ Tractors
0505 - T1
DESCRIPTION OF CONCERN 3. The ATC controller is now a part of the Data Bus.
Changes have been made in the fault codes on these 4. Two new tractor models have been added:
tractors since bulletin 3/03-T3 was released. TJ425HD and TJ450HD.
ACTION/CORRECTION All new codes have been identified in the attached

lists by two asterisks (**) printed as the first
To assist the field in diagnostics, a complete list of characters in the first column.
fault codes is attached to this bulletin.
Continue to use bulletin 3/03-T3 for tractors built prior
Production: to serial number to RVS003801.
The attached changes went into production on all TJ
Series tractors built after serial number RVS003800. PARTS AFFECTED
NA
Service:
The following changes took effect at serial number WARRANTY STATUS
RVS003801: This service bulletin is for information purposes only
and does not constitute warranty authorization to
1. The ICU2 (or New Generation Instrument update units without a warrantable failure.
Cluster) replaced the ”ICU” or ”New Generation
55 440
ICU and Performance” Monitor, when equipped.
2. The ARU2 (or New Generation Armrest
Controller) replaced the ARU.
©2005 CNH America LLC All rights reserved.
34
TRACTORS
ARMREST CONTROLER (ARM) FAULTS

Controller Id Error Id Error Text (Reference Only)
ARM 19 Hand THROTTLE potentiometer is failed
ARM 29 Aux 1st remote valve LEVER potentiometer is failed
ARM 39 Aux 2nd remote valve LEVER potentiometer is failed
ARM 49 Aux 3rd remote valve LEVER potentiometer is failed
ARM 59 Aux 4th remote valve LEVER potentiometer is failed
ARM 69 HITCH POSITION command potentiometer is failed
ARM 79 Invalid Configuration -- HITCH LOAD command potentiometer is failed
ARM 89 Aux 1st remote valve FLOW potentiometer is failed
ARM 99 Aux 2nd remote valve FLOW potentiometer is failed
ARM 109 Aux 3rd remote valve FLOW potentiometer is failed
ARM 119 Aux 4th remote valve FLOW potentiometer is failed
ARM 129 Aux 5th remote valve FLOW potentiometer is failed
ARM 139 Aux remote valve TIMER potentiometer is failed
ARM 149 Hitch UPPER LIMIT potentiometer is failed
ARM 159 Hitch DROP RATE potentiometer is failed
ARM 169 Invalid Configuration -- Hitch TRAVEL potentiometer is failed
ARM 1019 Trans GEAR SELECTION switch is failed
ARM 1029 Aux 5th remote valve control switch is failed
ARM 1039 Invalid Configuration -- PTO switch is failed
ARM 1049 Hitch UP/DOWN switch is failed
ARM 1059 Hitch SLIP switch is failed
ARM 1069 Invalid Configuration -- MFD switch is failed
ARM 1079 Invalid Configuration -- Diff lock switch is failed
**ARM 1089 Invalid Configuration -- Programmable Up/Down switch is failed
ARM 1099 Aux remote valve LIMIT SET switch is failed
ARM 1109 Hand Throttle IDLE VALIDATION switch is failed
**ARM 1119 Invalid Configuration -- HTS Play/Record switch is failed
**ARM 1129 Invalid Configuration -- Implement Depth Control switch is failed
**ARM 1139 Engine brake switch is failed
ARM 8011 Battery Voltage is too Low
ARM 9011 Controller Memory Error -- Loss of Hitch Position Command Calibration
ARM 9012 Controller Memory Error -- Loss of Aux Remote Lever Calibrations
ARM 9013 Controller Memory Error -- Loss of Throttle Calibrations
ARM 9014 Invalid Configuration -- Loss of MFD switch Configuration
ARM 9015 Invalid Configuration -- Loss of Trans switches Configuration
ARM 9021 Hitch position command potentiometer calibration results not acceptable
ARM 9031 Hand throttle potentiometer calibration results not acceptable
ARM 10091 Armrest Controller failure -- 5 V regulator failure
ARM 12013 Communications Lost with Data Bus and ALL other controllers
**ARM 12081 Communications Lost with Instrumentation controller (Performance Monitor functions)
ARM 65535 NO ERROR. Errors have not been cleared from factory.
35
TRACTORS
REMOTE (AUX) CONTROLLER FAULTS

AUX 1010 Aux remote valve EXTEND LIMIT SET switch is failed in the Armrest Controller
AUX 1020 Aux remote valve RETRACT LIMIT SET switch is failed in the Armrest Controller
AUX 1030 Aux 1st remote valve Timer Switch is failed in the Armrest Controller
AUX 1040 Aux 2nd remote valve Timer Switch is failed in the Armrest Controller
AUX 1050 Aux 3rd remote valve Timer Switch is failed in the Armrest Controller
AUX 1060 Aux 4th remote valve Timer Switch is failed in the Armrest Controller
AUX 1090 Aux 5th remote valve control switch (Extend) is failed in the Armrest Controller
AUX 1100 Aux 5th remote valve control switch (Retract) is failed in the Armrest Controller
AUX 8011 Battery Voltage is too Low
AUX 8012 Battery Voltage is too High
AUX 9009 Controller Memory Error -- Loss of valve constants
AUX 9019 Controller Memory Error -- Loss of operator adjustment data
AUX 9029 Controller Memory Error -- Loss of valve calibration data
AUX 11010 Aux 1st remote valve LEVER potentiometer is failed in the Armrest Controller
AUX 11020 Aux 2nd remote valve LEVER potentiometer is failed in the Armrest Controller
AUX 11030 Aux 3rd remote valve LEVER potentiometer is failed in the Armrest Controller
AUX 11040 Aux 4th remote valve LEVER potentiometer is failed in the Armrest Controller
AUX 11060 Aux 1st remote valve FLOW potentiometer is failed in the Armrest Controller
AUX 11070 Aux 2nd remote valve FLOW potentiometer is failed in the Armrest Controller
AUX 11080 Aux 3rd remote valve FLOW potentiometer is failed in the Armrest Controller
AUX 11090 Aux 4th remote valve FLOW potentiometer is failed in the Armrest Controller
AUX 11100 Aux 5th remote valve FLOW potentiometer is failed in the Armrest Controller
AUX 11110 Aux remote valve TIMER potentiometer is failed in the Armrest Controller
AUX 12011 Communications Lost with Armrest Controller
AUX 12041 Communications Lost with Instrumentation Controller
AUX 12081 Communications Lost with Performance Controller.
AUX 51011 Aux Remote Controller failure -- Valve Supply Relay Open
AUX 51012 Aux Remote Controller failure -- Valve Supply Relay Voltage High
AUX 51029 Valve supply voltage high before valve power relay is closed.
AUX 51031 Aux Remote Controller failure -- Valve Current Enable Protection Low
AUX 51032 Aux Remote Controller failure -- Valve Current Enable Protection High
AUX 51039 Aux Remote Controller failure -- Valve Current Enable Protection Failed
AUX 51041 Aux Remote Controller failure -- Valve Current Limit Protection Low
AUX 51042 Aux Remote Controller failure -- Valve Current Limit Protection High
AUX 51049 Aux Remote Controller failure -- Valve Current Limit Protection Failed
AUX 51053 Aux 1st Lower Coil solenoid shorted to 12 volts.
AUX 51054 Aux 1st Raise Coil solenoid shorted to 12 volts.
AUX 51055 Aux 1st Lower solenoid failed open or short circuit.
36
TRACTORS
REMOTE (AUX) CONTROLLER FAULTS (CONTINUED)

AUX 51056 Aux 1st Raise solenoid failed open or short circuit.
AUX 51063 Aux 2nd Lower Coil solenoid shorted to 12 volts.
AUX 51064 Aux 2nd Raise Coil solenoid shorted to 12 volts.
AUX 51065 Aux 2nd Lower solenoid failed open or short circuit.
AUX 51066 Aux 2nd Raise solenoid failed open or short circuit.
AUX 51073 Aux 3rd Lower Coil solenoid shorted to 12 volts.
AUX 51074 Aux 3rd Raise Coil solenoid shorted to 12 volts.
AUX 51075 Aux 3rd Lower solenoid failed open or short circuit.
AUX 51076 Aux 3rd Raise solenoid failed open or short circuit.
AUX 51083 Aux 4th Lower Coil solenoid shorted to 12 volts.
AUX 51084 Aux 4th Raise Coil solenoid shorted to 12 volts.
AUX 51085 Aux 4th Lower solenoid failed open or short circuit.
AUX 51086 Aux 4th Raise solenoid failed open or short circuit.
AUX 51093 Aux 5th Lower Coil solenoid shorted to 12 volts.
AUX 51094 Aux 5th Raise Coil solenoid shorted to 12 volts.
AUX 51095 Aux 5th Lower solenoid failed open or short circuit.
AUX 51096 Aux 5th Raise solenoid failed open or short circuit.
AUX 51101 Invalid Software Instruction Executed
37
TRACTORS
REMOTE (AUX) CONTROLLER FAULTS (CONTINUED)

AUX 51200 Aux remote valve LIMIT SET switch is failed in the Armrest Controller
AUX 51250 Aux 5th remote valve control switch is failed in the Armrest Controller
AUX 51261 Implement Sensor supply out of range Low.
AUX 51262 Implement Sensor supply out of range High.
AUX 51401 Implement feedback #1 out of range Low
AUX 51402 Implement feedback #1 out of range High
AUX 51411 Implement feedback #2 out of range Low
AUX 51412 Implement feedback #2 out of range High
AUX 65535 NO ERROR. Errors have not been cleared from factory.
38
TRACTORS
REMOTE 6 AND 7 (AUX67) CONTROLLER FAULTS

AUX67 8011 Battery Voltage is too Low
AUX67 8012 Battery Voltage is too High
AUX67 9009 Controller Memory Error -- Loss of valve constants
AUX67 9019 Controller Memory Error -- Loss of Operator Adjustment Data
AUX67 9029 Controller Memory Error -- Loss of Valve Calibration Data
AUX67 9039 Controller Memory Error -- Loss of mode lever calibration data
AUX67 11011 1st remote MODE LEVER potentiometer is failed low.
AUX67 11012 1st remote MODE LEVER potentiometer is failed high.
AUX67 11021 2nd remote MODE LEVER potentiometer is failed low.
AUX67 11022 2nd remote MODE LEVER potentiometer is failed high.
AUX67 11061 1st remote FLOW potentiometer is failed low.
AUX67 11062 1st remote FLOW potentiometer is failed high.
AUX67 11071 2nd remote FLOW potentiometer is failed low.
AUX67 11072 2nd remote FLOW potentiometer is failed high.
AUX67 11081 1st remote FLOW potentiometer SENSE is failed low.
AUX67 11082 1st remote FLOW potentiometer SENSE is failed high.
AUX67 11091 2nd remote FLOW potentiometer SENSE is failed low.
AUX67 11092 2nd remote FLOW potentiometer SENSE is failed high.
AUX67 11111 1st remote TIMER potentiometer is failed low.
AUX67 11112 1st remote TIMER potentiometer is failed high.
AUX67 11121 2nd remote TIMER potentiometer is failed low.
AUX67 11122 2nd remote TIMER potentiometer is failed high.
AUX67 11131 1st remote TIMER potentiometer SENSE is failed low.
AUX67 11132 1st remote TIMER potentiometer SENSE is failed high.
AUX67 11141 2nd remote TIMER potentiometer SENSE is failed low.
AUX67 11142 2nd remote TIMER potentiometer SENSE is failed high.
AUX67 12022 Duplicate Source Address Detected.
AUX67 12023 Invalid Source Address Controller.
AUX67 12041 Communications Lost witn instrumentation Controller.
AUX67 51011 Remote Controller Failure -- Valve supply relay open.
AUX67 51012 Remote Controller Failure -- Valve supply relay voltage high.
AUX67 51029 Valves supply voltage high before valve power relay is closed.
AUX67 51039 Remote Controller Failure -- Valve Current Enable Protection Failed
AUX67 51049 Remore Controller Failure -- Valve Current Limit Protection Failed.
AUX67 51053 1st Lower Coil solenoid shorted to 12 volts.
AUX67 51054 1st Raise Coil solenoid shorted to 12 volts.
AUX67 51055 1st Lower solenoid failed open or a short circuit to ground.
AUX67 51056 1st Raise solenoid failed open or a short circuit to ground.
AUX67 51063 2nd Lower Coil solenoid shorted to 12 volts.
39
TRACTORS
REMOTE 6 AND 7 (AUX67) CONTROLLER FAULTS (CONTINUED)

AUX67 51064 2nd Raise Coil solenoid shorted to 12 volts.
AUX67 51065 2nd Lower solenoid failed open or a short circuit to ground.
AUX67 51066 2nd Raise solenoid failed open or a short circuit to ground.
AUX67 51261 Implement Sensor supply out of range Low.
AUX67 51262 Implement Sensor supply out of range High.
AUX67 51301 On--Board logic voltage out of range Low.
AUX67 51302 On--Board logic voltage out of range High.
AUX67 51401 Implement feedback #1 out of range Low.
AUX67 51402 Implement feedback #1 out of range High.
AUX67 51509 Auto mode status lamp open circuit or shorted to ground.
AUX67 65535 NO ERROR. Errors have not been cleared from factory.
40
TRACTORS
REMOTES 8 AND 9 (AUX89) CONTROLLER FAULTS

AUX89 8011 Battery Voltage is too Low
AUX89 8012 Battery Voltage is too High
AUX89 9009 Controller Memory Error -- Loss of valve constants
AUX89 9019 Controller Memory Error -- Loss of Operator Adjustment Data
AUX89 9029 Controller Memory Error -- Loss of Valve Calibration Data
AUX89 9039 Controller Memory Error -- Loss of mode lever calibration data
AUX89 11011 1st remote MODE LEVER potentiometer is failed low.
AUX89 11012 1st remote MODE LEVER potentiometer is failed high.
AUX89 11021 2nd remote MODE LEVER potentiometer is failed low.
AUX89 11022 2nd remote MODE LEVER potentiometer is failed high.
AUX89 11061 1st remote FLOW potentiometer is failed low.
AUX89 11062 1st remote FLOW potentiometer is failed high.
AUX89 11071 2nd remote FLOW potentiometer is failed low.
AUX89 11072 2nd remote FLOW potentiometer is failed high.
AUX89 11081 1st remote FLOW potentiometer SENSE is failed low.
AUX89 11082 1st remote FLOW potentiometer SENSE is failed high
AUX89 11091 2nd remote FLOW potentiometer SENSE is failed low.
AUX89 11092 2nd remote FLOW potentiometer SENSE is failed high.
AUX89 11111 1st remote TIMER potentiometer is failed low.
AUX89 11112 1st remote TIMER potentiometer is failed high.
AUX89 11121 2nd remote TIMER potentiometer is failed low.
AUX89 11122 2nd remote TIMER potentiometer is failed high.
AUX89 11131 1st remote TIMER potentiometer SENSE is failed low.
AUX89 11132 1st remote TIMER potentiometer SENSE is failed high.
AUX89 11141 2nd remote TIMER potentiometer SENSE is failed low.
AUX89 11142 2nd remote TIMER potentiometer SENSE is failed high.
AUX89 12022 Duplicate Source Address Detected.
AUX89 12023 Invalid Source Address Controller.
AUX89 12041 Communications Lost witn instrumentation Controller.
AUX89 51011 Remote Controller Failure -- Valve supply relay open.
AUX89 51012 Remote Controller Failure -- Valve supply relay voltage high.
AUX89 51029 Valves supply voltage high before valve power relay is closed.
AUX89 51039 Remote Controller Failure -- Valve Current Enable Protection Failed
AUX89 51049 Remore Controller Failure -- Valve Current Limit Protection Failed
AUX89 51053 1st Lower Coil solenoid shorted to 12 volts.
AUX89 51054 1st Raise Coil solenoid shorted to 12 volts.
AUX89 51055 1st Lower solenoid failed open or a short circuit to ground.
AUX89 51056 1st Raise solenoid failed open or a short circuit to ground.
AUX89 51063 2nd Lower Coil solenoid shorted to 12 volts.
41
TRACTORS
REMOTES 8 AND 9 (AUX89) CONTROLLER FAULTS (CONTINUED)

AUX89 51064 2nd Raise Coil solenoid shorted to 12 volts.
AUX89 51065 2nd Lower solenoid failed open or a short circuit to ground.
AUX89 51066 2nd Raise solenoid failed open or a short circuit to ground.
AUX89 51261 Implement Sensor supply out of range Low.
AUX89 51262 Implement Sensor supply out of range High.
AUX67 51301 On--Board logic voltage out of range Low.
AUX67 51302 On--Board logic voltage out of range High.
AUX89 51401 Implement feedback #1 out of range Low.
AUX89 51402 Implement feedback #1 out of range High.
AUX89 51509 Auto mode status lamp open circuit or shorted to ground.
AUX89 65535 NO ERROR. Errors have not been cleared from factory.
42
TRACTORS
AUTOMATIC TEMPERATURE CONTROLLER (ATC) FAULTS

** ATC 111 Cab sensor open or shorted to power
** ATC 112 Cab sensor shorted to ground
** ATC 115 Evaporator sensor open or shorted to power
** ATC 116 Evaporator sensor shorted to ground
** ATC 119 Auto and Manual switch both on
** ATC 120 Blower speed select pot open/shorted to power
** ATC 121 Temperature select pot open/shorted to power
** ATC 122 Mode Door potentiometer open circuit or shorted to power
** ATC 123 Cab pressure sensor input shorted to power
** ATC 124 Cab pressure sensor input shorted to ground
** ATC 125 High pressure switch (+) input shorted to power
** ATC 126 High pressure switch (+) input shorted to ground
** ATC 127 High pressure switch (--) input shorted to power
** ATC 128 High pressure switch (--) input shorted to ground
** ATC 129 High pressure cycling error (2 in 1 minute)
** ATC 130 Low pressure switch (+) input shorted to power
** ATC 131 Low pressure switch (+) input shorted to ground
** ATC 132 Low pressure switch (--) input shorted to power
** ATC 133 Low pressure switch (--) input shorted to ground
** ATC 134 Low pressure switch open for > 1 minute
** ATC 135 Clutch output fault (overcurrent, short to ground)
** ATC 136 Defog light output fault (overcurrent, short to ground)
** ATC 137 Controller Fault (EEPROM error)
** ATC 65535 NO ERROR. Errors have not been cleared from factory.
43
TRACTORS
ENGINE (ECM) CONTROLLER FAULTS

Controller Id # Posposed combined description 8.3/9.0 15
Liter Liter
ENG 111 Engine Controller Failure -- Hardware Failure X X
ENG 115 Engine Speed Sensor (8.3, 9 Liter) or Cam Sensor (15 Liter) is failed X X
ENG 121 Engine Position Sensor(8.3, 9 Liter) or Crankshaft Sensor (15 Liter) is X X
failed
ENG 122 Boost Pressure Sensor voltage is too high X X
ENG 123 Boost Pressure Sensor voltage is too low X X
ENG 124 Boost Pressure level has exceeded the warning limit X
ENG 131 Decelerator or Hand Throttle (STD cab) Position potentiometer X X
voltage is too high
ENG 132 Decelerator or Hand Throttle (STD cab) Position potentiometer X X
voltage is too low
ENG 133 Decelerator (STD cab) Position potentiometer voltage is too high X X
ENG 134 Decelerator (STD cab) Position potentiometer voltage is too low X X
ENG 135 Oil Pressure Sensor voltage is too high X X
ENG 141 Oil Pressure Sensor voltage is too low X X
ENG 143 Oil Pressure level has fallen below the warning limit. X X
ENG 144 Coolant Temperature Sensor voltage is too high X X
ENG 145 Coolant Temperature Sensor voltage is too low X X
ENG 146 Coolant Temperature level has exceeded the warning limit. X
ENG 147 Frequency Throttle Signal shorted high X X
ENG 148 Frequency Throttle Signal shorted low X X
ENG 151 Coolant Temperature level has exceeded the warning limit. X X
ENG 153 Intake Manifold Temperature Sensor voltage is too high X X
ENG 154 Intake Manifold Temperature Sensor voltage is too low X X
ENG 155 Intake Manifold Temperature level has exceeded the warning limit. X X
ENG 187 Sensor Supply 2 Voltage is too low. X
ENG 191 A/C clutch driver shorted to ground when ON. X
ENG 211 Communications problem with Armrest, Instrumentation, or Transmis- X X
sion Controllers
ENG 212 Oil Temperature Sensor Voltage is too high X
ENG 213 Oil Temperature Sensor Voltage is too low X
ENG 214 Oil Temperature Sensor Voltage is above normal range X
ENG 219 Oil Level -- remote reservoir is too low. Add oil. X
ENG 221 Ambient Air Pressure Sensor Voltage is too high X X
ENG 222 Ambient Air Pressure Sensor Voltage is too low X X
ENG 223 CORS -- Burn Valve Solenoid is shorted either low or high X
ENG 227 Sensor Supply 2 Voltage is too high. X
ENG 234 Engine Speed has exceed the overspeed warning limit. X X
ENG 235 Engine Coolant Level is low. Add coolant fluid. X X
44
TRACTORS
ENGINE (ECM) CONTROLLER FAULTS (CONTINUED)

Liter Liter
ENG 237 External Speed Multi Unit Sync Command Input Data Incorrect. X
ENG 241 Vehicle Speed Signal lost X
ENG 242 Vehicle Speed Signal intermittent / tampering X
ENG 243 Error detected in exhaust brake relay X
ENG 245 Fan Clutch Voltage too low X X
ENG 254 Fuel Shutoff Valve Voltage too low X
ENG 255 Fuel Shutoff Valve Voltage too high X
ENG 259 Fuel Shutoff Valve mechanically stuck open. X
ENG 263 Fuel Temperature Sensor voltage is too high X
ENG 265 Fuel Temperature Sensor voltage is too low X
ENG 268 Fuel Pressure in pump is not changing with operating conditions. X
ENG 271 Front Pumping Control Valve current is low during ”click test” X
ENG 272 Front Pumping Control Valve current is high X
ENG 273 Rear Pumping Control Valve current is low during ”click test” X
ENG 274 Rear Pumping Control Valve current is high X
ENG 275 Front Pumping element is failed X
ENG 276 Injection Control Valve current is out of range X
ENG 277 Injection Control Valve is failed X
ENG 278 Fuel Lift Pump is failed X
ENG 279 Injection Control Valve current is out of range X
ENG 281 Front Pumping element is failed X
ENG 282 Rear Pumping element is failed X
ENG 283 Engine Speed/Position Sensor supply voltage is too high X
ENG 284 Engine Speed/Position Sensor supply voltage is too low X X
ENG 285 J1939 Parameter was set to be multiplexed, but was not received X
(timeout error)
ENG 286 J1939 Parameter was set to be multiplexed, but was not available from X
all sources (config error)
ENG 287 Multiplexing throttle parameter and a data error was received -- data X X
invalid
ENG 288 Multiplexing remote throttle parameter and a data error was received X X
-- data invalid
ENG 293 Hydraulic Fan Hydraulic Oil Temperature Sensor Voltage is too high X
ENG 294 Hydraulic Fan Hydraulic Oil Temperature Sensor Voltage is too low X
ENG 295 Ambient Air Pressure data invalid X
ENG 297 OEM Pressure Sensor Voltage is too high. X X
ENG 298 OEM Pressure Sensor Voltage is too low. X X
ENG 299 Engine Shutdown by other than keyswitch (i.e. via data bus command) X
ENG 319 Real Time Clock in controller has lost power X X
45
TRACTORS

Liter Liter
ENG 328 Rear Pumping element is failed X
ENG 329 CAPS Pump has an overpumping failure X
ENG 338 Idle Shutdown Vehicle Accessory Relay Voltage is too high X
ENG 339 Idle Shutdown Vehicle Accessory Relay Voltage is too low X
ENG 341 All data written during powerdown cycle was lost (checksum error) X
ENG 343 Engine Controller Failure -- Hardware Failure X
ENG 349 Measured Speed is too high. X X
ENG 352 5 Volt Sensor Supply voltage is too low X X
ENG 378 Front Fueling current is too low X
ENG 379 Front fueling current is too high X
ENG 381 Error detected in cold start relay 1 X
ENG 382 Error detected in cold start relay 2 X
ENG 385 5 Volt Sensor Supply voltage is too high X
ENG 386 5 Volt Sensor Supply voltage is too high X X
ENG 387 Decelerator or Hand Throttle (STD cab) 5 Volt Supply voltage is too X X
high
ENG 388 Engine Brake driver 1 circuit failure X
ENG 394 Front Timing current is too low. X
ENG 395 Front Timing current is too high. X
ENG 396 Rear Fueling current is too low X
ENG 397 Rear Fueling current is too high X
ENG 398 Rear Timing current is too low X
ENG 399 Rear Timing current is too high X
ENG 412 J1708 data link cannot transmit X
ENG 414 J1708 data link not fast enough X
ENG 415 Oil Pressure level has fallen below the very low warning limit. X X
ENG 418 Water in Fuel sensor indicates the water in the fuel filter needs to be X X
drained.
ENG 419 Boost Pressure data invalid X
ENG 422 Engine Coolant Level Sensor (optional) is failed or the jumper plug is X X
missing
ENG 426 J1939 data link cannot transmit X
ENG 427 J1939 data link not fast enough X
ENG 428 Water in Fuel Sensor voltage is too high. X
ENG 429 Water in Fuel Sensor voltage is too low. X X
ENG 431 Hand Throttle (STD cab) Idle Validation Switches are both closed X X
46
TRACTORS

Liter Liter
ENG 432 Hand Throttle (STD cab) position potentiometer and switches X X
disagree.
ENG 433 Boost Pressure level disagrees with engine operation conditions X X
(speed & power)
ENG 434 Unswitched 12 volt supply voltage disconnected without normal key X X
off sequence.
ENG 435 Oil Pressure data invalid X
ENG 441 Battery Voltage is too Low (less than 6 volts) X X
ENG 442 Battery Voltage is too High X X
ENG 443 Decelerator or Hand Throttle (STD cab) 5 Volt Supply voltage is too X X
low
ENG 444 Low voltage detected at OEM 5 volt supply X
ENG 449 Fuel Pressure level has exceeded the warning limit. X X
ENG 451 Fuel Pressure Sensor voltage is too high X X
ENG 452 Fuel Pressure Sensor voltage is too low X X
ENG 456 Fuel pressure in pump is not changing with operating conditions. X
ENG 465 Wategate 1 voltage is too high X
ENG 466 Wategate 1 voltage is too low X
ENG 482 Fuel Pressure Sensor voltage low X
ENG 483 Rear Bank Post Actuactor Pressure voltage high X
ENG 484 Rear Bank Post Actuactor Pressure voltage low X
ENG 485 Rear Fueling actuator overfueling X
ENG 486 Rear Fueling actuator underfueling X
ENG 488 Intake Manifold Temperature level has exceeded the warning limit. X
ENG 489 Measured Speed Sensor data low X X
ENG 491 Wategate 2 voltage is too high X
ENG 492 Wategate 2 voltage is too low X
ENG 493 The Injection Control Identifier Circuit in the harness has failed. X
ENG 496 Engine Speed / Position Sensor #2 supply is too low X
ENG 524 Error detected on high speed governor droop selection switch X
ENG 527 Cab pressurization/Ether relay coil circuit shorted high or open X X
ENG 529 Output B driver shorted high or open X X
ENG 539 The Injection Control Valve Transorb in the harness has failed. (open X
circuit)
ENG 546 Fuel Pressure sensor voltage is too high. X
ENG 547 Fuel Pressure sensor voltage is too low. X
ENG 551 Hand Throttle (STD cab) Idle Validation Switches are both open X X
ENG 553 Front fueling actuator overfueling X
ENG 559 Front fueling actuator underfueling X
47
TRACTORS

Liter Liter
ENG 581 Fuel inlet Pressure Sensor voltage is too high. X
ENG 582 Fuel inlet Pressure Sensor voltage is too low. X
ENG 583 Fuel Inlet Pressure Sensor voltageout of range high or low. X
ENG 595 Turbo overspeed protection fault X
ENG 596 Battery voltage is too high X
ENG 597 Battery voltage is too low X
ENG 598 Battery voltage is very low X
ENG 599 Engine is being shutdown based on OEM input X
ENG 611 ECM detected engine initiated protection shutdown or keyed--off while X X
above specific load limit
ENG 697 Engine Controller internal temperature too high X
ENG 698 Engine Controller internal temperature too low X
ENG 731 Engine Speed / Position #2 -- Mechanical misalignment. X
ENG 753 Synchronization has been lost. X
ENG 755 Front Bank injector is bad. X
ENG 758 Rear Bank injector is bad X
ENG 951 A power imbalance between the cylinders was detected by the X
controller hardware
ENG 983 Unused A/D input channel out of range. X
48
TRACTORS
HITCH CONTROLLER FAULT CODES

Controller Error Error Text (Reference Only)
Id Id
HITCH 1010 Hitch Up/Down Switch failed in the Armrest controller
HITCH 1020 Hitch Slip Select Switch failed in the Armrest controller
HITCH 1030 Hitch Slip Set Switch failed in the Armrest controller
HITCH 3010 Transmission Output Speed Sensor is failed in the Instrumentation Controller
HITCH 3020 Slip Sensor (radar or wheel speed) is failed in the Instrumentation Controller
HITCH 3030 Engine Speed Sensor is failed in the Engine Controller
HITCH 4019 Invalid Configuration -- Right Draft Pin voltage is outside the normal operating range.
HITCH 4029 Invalid Configuration -- Left Draft Pin voltage is outside the normal operating range.
HITCH 4039 Invalid Config.-- Left and Right Draft Pin voltages are outside the normal operating
range.
HITCH 4049 Invalid Configuration -- Single draft pin is outside the normal operating range.
HITCH 6014 Hitch Lower Solenoid is failed open or shorted to the ground
HITCH 6015 Hitch Lower Solenoid is failed shorted to the 12 volts
HITCH 6024 Hitch Raise Solenoid is failed open or shorted to the ground
HITCH 6025 Hitch Raise Solenoid is failed shorted to the 12 volts
HITCH 8001 Battery Voltage is too Low
HITCH 8002 Battery Voltage is too High
HITCH 9301 Raise Valve calibration value is too high. (valve problem)
HITCH 9302 Raise Valve calibration value is too low. (valve problem)
HITCH 9303 Raise Valve current measurement problem during calibration
HITCH 9304 Hitch position at top of travel is not within specification during calibration
HITCH 9306 Lower Valve calibration value is too high. (valve problem)
HITCH 9307 Lower Valve calibration value is too low. (valve problem)
HITCH 9308 The time allowed for hitch calibration has expired
HITCH 9309 Hitch position at bottom of travel is not within specification during calibration
HITCH 9310 Hitch position range from top to bottom is not within spec during calibration
HITCH 9311 Hitch position to hitch rockershaft position ratio is not within spec during calibration
HITCH 9312 Invalid Configuration -- Draft pin connected to left vs right for single pin setup
HITCH 9313 Invalid Configuration -- Hitch setup for position only due to Armrest configuration
HITCH 9314 Invalid Config. -- Right Draft Pin voltage is not within spec for ’no load’ condition
HITCH 9315 Invalid Config. -- Left Draft Pin voltage is not within spec for ’no load’ condition
HITCH 9316 Invalid Config. -- Both Draft Pin voltages are not within spec for ’no load’ condition
HITCH 9317 The Hitch Controller Calibration procedure must be performed.
HITCH 9318 Engine speed must be set above 1600 rpm during calibration of lower valve.
HITCH 9319 Invalid Config.-- Hitch calibrated for position only but Armrest calibrated for draft mode
HITCH 9320 Hitch calibration aborted due to tractor movement.
HITCH 9321 Hitch calibration attempted when the engine is not running or engine speed signal is
failed.
HITCH 10030 Controller Memory Error -- Loss of hitch calibration data. Re--calibrate hitch.
49
TRACTORS
HITCH CONTROLLER FAULT CODES (CONTINUED)

Controller Error Error Text (Reference Only)
Id Id
HITCH 10060 Internal controller relay failed or hitch valves shorted to 12 volts.
HITCH 10061 Internal controller relay failed or hitch valves open circuit or shorted to ground.
HITCH 10071 Controller failure -- Lower valve driver is shorted to 12 volts.
HITCH 10072 Controller failure -- Raise valve driver is shorted to 12 volts.
HITCH 10090 Controller failure -- 5 volt regulator has failed.
HITCH 11010 Invalid Configuration--Hitch Load Command potentiometer is failed in the Armrest
Controller
HITCH 11020 Hitch Drop Rate potentiometer is failed in the Armrest Controller
HITCH 11030 Invalid Configuration -- Hitch Travel potentiometer is failed in the Armrest Controller
HITCH 11050 Hitch Upper Limit potentiometer is failed in the Armrest Controller
HITCH 11069 Hitch Rockshaft Position potentiometer is outside normal operating range.
HITCH 11070 Hitch Position Command potentiometer failed in the Armrest controller
HITCH 12011 Communications Lost with Armrest Controller
HITCH 12031 Communications Lost with Data Bus and ALL other controllers
HITCH 12041 Communications Lost with Instrumentation Controller
HITCH 52230 Upper Limit control is set below the position of the hitch.
HITCH 52260 Remote hitch UP and DOWN switch failure
HITCH 65535 NO ERROR. Errors have not been cleared from factory.
50
TRACTORS
INSTRUMENT CLUSTER (ICU2) FAULTS

INST2 1015 Seat Switch may be stuck closed.
INST2 3010 Invalid Configuration -- PTO Shaft Speed Sensor is failed in PTO Controller
INST2 3020 Engine Speed sensor is failed in the Engine Controller
**INST2 3022 Invalid Configuration -- Engine has been run Overspeed
INST2 5010 Engine Oil Pressure sensor is failed in the Engine Controller
INST2 5011 Invalid Configuration -- Engine Oil Pressure sensor voltage is too low
INST2 10031 Controller Memory Error -- Loss of Engine Hours information
INST2 10032 Controller Memory Error -- Loss of Vehicle Configuration information
INST2 10033 Controller Memory Error -- Loss of Customer Configuration information
INST2 10035 Controller Memory Error -- Loss of Valid Radar Configuration information.
**INST2 10036 Controller Memory Error -- Loss of Valid Timer information.
**INST2 10037 Controller Memory Error -- Loss of Valid Implement Width information.
**INST2 10038 Controller Memory Error -- Loss of Valid Remote Timer information.
INST2 11011 Fuel Level Sensor voltage is too low (open circuit, short to ground)
INST2 12011 Communications Lost with Armrest Controller
INST2 12021 Communications Lost with Auxiliary Controller
INST2 12022 Communications Lost with Aux67 Controller.
INST2 12023 Communications Lost with Aux89 Controller.
INST2 12031 Communications Lost with Hitch Controller
INST2 12043 Communications Lost with Data Bus and ALL other controllers
INST2 12051 Invalid Configuration -- Communications Lost with PTO Controller
INST2 12061 Communications Lost with Steering Controller
INST2 12071 Communications Lost with Transmission Controller
INST2 12091 Communications Lost with Engine Controller
**INST2 12101 Invalid Configuration -- Communications Lost with Tractor ECU Controller
**INST2 12111 Communications Lost with Automatic Temperature Controller
**INST2 12121 Invalid Configuration -- Communications Lost with SWCD Controller
INST2 13010 Engine Coolant Temperature sensor is failed in the Engine Controller
INST2 13011 Invalid Configuration -- Engine Coolant Temperature sensor voltage is too low
INST2 13012 Invalid Configuration -- Engine Coolant Temperature sensor voltage is too high
INST2 13021 Transmission Oil Temperature sensor voltage is too low (short to ground)
INST2 13022 Transmission Oil Temperature sensor voltage is too high (open circuit, short to +V)
INST2 13031 Hydraulic Oil Temperature sensor voltage is too low (short to ground)
INST2 13032 Hydraulic Oil Temperature Sensor voltage is too high (open circuit, short to +V)
INST2 13040 Air to Air Intake Temperature sensor is failed in the Engine Controller
INST2 13044 Incorrect Inst controller on tractor or differential lock relay coil current is too high
INST2 13051 Invalid Configuration -- Air to Air Intake Temperature sensor voltage is too low
INST2 13052 Invalid Configuration -- Air to Air Intake Temperature sensor voltage is too high
INST2 53001 Instrumentation Controller Configuration is Incorrect
INST2 53002 Invalid Configuration--Air to Air Intake sensor does not match Tractor Model Configuration
INST2 65535 NO ERROR. Errors have not been cleared from factory.
51
TRACTORS
TRANSMISSION CONTROLLER (TRANS) FAULTS

Controller Error Id Error Text (Reference Only)
Id
TRANS 3010 Engine Speed sensor is failed in the Engine Controller.
TRANS 3011 Engine has stalled causing the Transmission to disengage.
TRANS 3012 Engine Speed is too high. (Greater than 4000 rpm)
TRANS 3020 Transmission Output Speed sensor is failed in the Instrumentation Controller
TRANS 3030 Invalid Tractor Model configured in the Instrumentation Controller.
TRANS 5041 Park Brake not engaged when in Park.
TRANS 5042 Park Brake engaged when not in Park.
TRANS 6115 Lube Valve Coil circuit is shorted to 12 volts when the valve is ON.
TRANS 6116 Lube Valve Coil circuit is open or shorted to ground.
TRANS 8011 Battery Voltage is too Low
TRANS 8012 Battery Voltage is too High
TRANS 10082 Transmission Controller Failure -- Internal short in the Lube Valve Coil circuit.
TRANS 10083 Transmission Controller Failure--Internal short in the Trans Neutral Latch Relay Coil
circuit.
TRANS 10091 Transmission Controller Failure -- Internal 5 volt supply voltage is too high.
TRANS 10092 Transmission Controller Failure -- Internal 5 volt supply voltage is too low.
TRANS 11011 Clutch Pedal Position potentiometer voltage is too Low
TRANS 11012 Clutch Pedal Position potentiometer voltage is too High
TRANS 12011 Communications Lost with Armrest Controller
TRANS 12041 Communications Lost with Instrumentation Controller
TRANS 12091 Communications Lost with Engine Controller
TRANS 13010 Transmission Oil temperature sensor is failed in the Instrumentation Controller
TRANS 56001 Shuttle Shift attempted from gear higher than shuttle shifting allowed.
TRANS 56002 The Transmission Controller Calibration procedure must be performed.
TRANS 56003 Controller Memory Error -- Loss of Forward Gear Pre--selection information.
TRANS 56004 Measured transmission output speed does not match the commanded transmission
output speed.
TRANS 56005 The stored Forward Gear Limit is invalid. Use Service Tool Config screen to reset
value.
TRANS 56014 The Transmission Control Lever is NOT in Park, Neutral, Forward or Reverse.
TRANS 56016 Clutch Pedal Position Sensor does not agree with Bottom of Clutch Pedal Switch.
TRANS 56022 Battery Voltage below valve operational limit (9V)
TRANS 56023 1F Valve Coil circuit is shorted to 12 volts when the valve is ON.
TRANS 56024 1M Valve Coil circuit is shorted to 12 volts when the valve is ON.
TRANS 56025 1R Valve Coil circuit is shorted to 12 volts when the valve is ON.
52
TRACTORS
TRANSMISSION CONTROLLER (TRANS) FAULTS (CONTINUED)

Id
TRANS 56032 System Pressure Valve Coil circuit is shorted to 12 volts when valve is ON.
TRANS 56033 1F Valve Coil circuit is open or shorted to ground when valve is ON.
TRANS 56034 1M Valve Coil circuit is open or shorted to ground when valve is ON.
TRANS 56035 1R Valve Coil circuit is open or shorted to ground when valve is ON.
TRANS 56042 System Pressure Valve Coil circuit is open or shorted to ground when valve is ON.
TRANS 56043 1F Valve Coil circuit is open or shorted to ground when valve is OFF.
TRANS 56044 1M Valve Coil circuit is open or shorted to ground when valve is OFF.
TRANS 56045 1R Valve Coil circuit is open or shorted to ground when valve is OFF.
TRANS 56052 System Pressure Valve Coil circuit is open or shorted to ground when valve is OFF.
TRANS 56064 The Neutral Lever Switch and either the Forward or Reverse Lever Switch are both
turned ON.
TRANS 56065 The Forward Lever Switch and the Reverse Lever Switch are both turned ON.
TRANS 56067 System pressure test point fault during pressure calibration.
TRANS 56068 Excessive engine load during valve calibration.
TRANS 56069 Master clutch valve calibration point out of range low.
TRANS 56070 Transmission Valve Calibration failed to find the clutch engagement value.
TRANS 56071 No Voltage to 4F or 4R Valves due to Neutral Relay or Bottom of Clutch Relay Fault
TRANS 56072 No Voltage detected on output of Transmission Neutral Latch Relay when it is ON.
(Relay Fault)
TRANS 56073 Unwanted Power to 4F/4R Valves due to short to 12 volts.
TRANS 56074 Voltage detected on output of Transmission Neutral Latch Relay when it is OFF.
(Relay Fault)
TRANS 56075 Unexpected vehicle motion during transmission calibration.
TRANS 56082 Transmission Gear Selection Switch is failed.
TRANS 56086 The Park Lever Switch does not agree with the Neutral Lever Switch.
53
TRACTORS
TRANSMISSION CONTROLLER (TRANS) FAULTS (CONTINUED)

Id
TRANS 56087 Trans Neutral Latch Relay Coil circuit is shorted to 12 volts when commanded ON.
TRANS 56088 Trans Neutral Latch Relay Coil circuit is open or shorted to ground when commanded
ON.
TRANS 56090 Trans Neutral Latch Relay Coil circuit is open or shorted to ground when commanded
OFF.
TRANS 56091 Transmission Controller Failure -- Internal ouput enable latch failed ON.
TRANS 56092 Diff Lock Relay Coil circuit is shorted to 12 volts when commanded ON.
TRANS 56093 System pressure is out of range high.
TRANS 56094 System pressure is out of range low.
TRANS 56095 Calibration average system pressure at cal point is out of range.
TRANS 56096 Calibration system pressure slope is out of range.
TRANS 56097 Calibration system pressure point is not reached.
TRANS 56098 The Select Shift Switch is ON at power up.
TRANS 56099 System pressure is out of range low (less than 517 kPa/75 PSI).
TRANS 56109 Transmission engagement aborted due to the Operator NOT being SEATED.
TRANS 56111 Trans Controller Failure -- Internal short in the 1F Valve Coil circuit.
TRANS 56112 Trans Controller Failure -- Internal short in the 1M Valve Coil circuit.
TRANS 56113 Trans Controller Failure -- Internal short in the 1R Valve Coil circuit.
TRANS 56120 Trans Controller Failure -- Internal short in the System Pressure Valve Coil circuit.
TRANS 56123 Engine Torque signal is failed in the Engine Controller or Communications lost with
Engine.
TRANS 65535 NO ERROR. Errors have not been cleared from factory.
54

Codigos 275

Uploaded by

Copyright:

Available Formats

Codigos 275

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Codigos 275

Uploaded by

Copyright:

Available Formats

TRACTORS

ACTION/CORRECTION All new codes have been identified in the attached

©2005 CNH America LLC All rights reserved.

ARMREST CONTROLER (ARM) FAULTS

REMOTE (AUX) CONTROLLER FAULTS

REMOTE (AUX) CONTROLLER FAULTS (CONTINUED)

REMOTE (AUX) CONTROLLER FAULTS (CONTINUED)

REMOTE 6 AND 7 (AUX67) CONTROLLER FAULTS

REMOTE 6 AND 7 (AUX67) CONTROLLER FAULTS (CONTINUED)

REMOTES 8 AND 9 (AUX89) CONTROLLER FAULTS

REMOTES 8 AND 9 (AUX89) CONTROLLER FAULTS (CONTINUED)

AUTOMATIC TEMPERATURE CONTROLLER (ATC) FAULTS

ENGINE (ECM) CONTROLLER FAULTS

ENGINE (ECM) CONTROLLER FAULTS (CONTINUED)

ENGINE (ECM) CONTROLLER FAULTS (CONTINUED)

ENGINE (ECM) CONTROLLER FAULTS (CONTINUED)

ENGINE (ECM) CONTROLLER FAULTS (CONTINUED)

HITCH CONTROLLER FAULT CODES

HITCH CONTROLLER FAULT CODES (CONTINUED)

INSTRUMENT CLUSTER (ICU2) FAULTS

TRANSMISSION CONTROLLER (TRANS) FAULTS

TRANSMISSION CONTROLLER (TRANS) FAULTS (CONTINUED)

TRANSMISSION CONTROLLER (TRANS) FAULTS (CONTINUED)

You might also like