BENZ Me97 Engine Programming-En

BENZ me97 Engine Programming
BENZ me97 Engine programming
一、Vehicle model supported:

Support E、S、C、SL、M、B、A、CL series 280 ECU programming from
BENZ
main system before year 2013 and part of year 2014.
二、Preparation for programming:

ArtiPad I main unit、connector、ArtiPad I standard configuration USB cable.
三、Programming precaution:
1、 Please keep the vehicle voltage stable at 13-14V.
2、 The programming process doesn’t operate any vehicle electrical equipment.
3、 Don’t sit in the car when programming.
4、 Don’t start the engine, and only open the ignition switch was OK.
5、 In order to ensure the speed and stability of programming. It was
recommended to connect ArtiPad I standard USB cable to do programming.
6、 If the engine was programmed, and the electrical fan may be running at high
speed. To ensure that battery was sufficient, please pull out electrical fan to do
programming again after turning off all the additional power 、lighting、air
condition、glass heating、seat heating. Etc.
四、Programming process:
Select“Local Diagnostic”Select BENZ iconControl module programming
Corresponding systemOnline download programming files （ Connect
WIFI、Login on account）Perform programmingCoding
1. Select “Local Diagnostic”, See picture 1;
1
Picture 1
2. Select MERCEDES icon , See picture 2;
2
Picture2
3. Select “Control module programming”，See picture3；
Picture3
4. The device can automatically identify VIN code after control module
programming, please check it and click “Yes” if the vin code was right. See
picture4；
3
Picture4
5.Select “OK”，See picture5；
Picture5
6.Enter the corresponding system programming ， here choose me97 engine as an
example to select “ECM-Engine Control Module(ME9.7)(Chassis CAN bus)” See
picture6；
4
Picture6
7.Select “Control unit Programming”，See picture7；
Picture7
8.It had some risk to do programming, please pay attention to view the risk tips and
precautions, and then select “OK” to continue. See picture8 ；
5
Picture8
9. Prompt “This function will need to download files” after click confirm, See picture
9;
Picture9
10.Click “Download” to start downloading the required files. and will list the specific
file name and some precautions to be programming after downloading completed.
Select “Yes” to start programming，See picture10；
Picture10
6
11. It had some risk to do programming, may lead engine control module abnormal. If
control module was normal so didn’t recommend you continue ,but if you want to do
programming please select “Yes” to perform it,See picture 11；
Picture11
12. Prompt programming process until 100% completed. See picture12；
7
Picture12
13. Prompt turn off ignition switch, waited 10 seconds and then open ignition switch.
At last showed “Control unit programming was completed successfully”. See
picture 13 to 16;
Picture13
8
Picture14
Picture15
9
Picture16
17.If vehicle was normal so needed not to do SCN coding(online coding)function, and
ended programming ;Otherwise do SCN coding(online coding) function if failed to
start engine. See picture17；
Picture17
18.The following procedure was for SCN online coding function, If the vehicle was
normal after programming so you can ignore all the next operation step, Otherwise
select the SCN coding(online code) menu, See picture18;
10
Picture18
19. Click “Yes” after keeping the internet connected. See picture19;
Picture19
20. Select “Download” to start downloading the coding files, there may be more than
one file, so it prompted to download several time, See picture20;
11
Picture20
21. Prompt “Downloaded successfully”. See picture21;
Picture21
22. Perform coding function after clicking confirm and prompt wait time., See
picture22;
12
Picture22
23. Need to reset ECU after coding completed, turn off the ignition and wait 10
seconds. And then turn on the ignition. The coding was completed. See picture 23 to
26;
Picture23
13
Picture24
Picture25
14
Picture26
27. If you cannot start engine after coding completed, please access to special
function and perform “driving license” or “initialization” function. See picture27;
Picture27
15

BENZ Me97 Engine Programming-En

Uploaded by

Copyright:

Available Formats

BENZ Me97 Engine Programming-En

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

BENZ Me97 Engine Programming-En

Uploaded by

Copyright:

Available Formats

BENZ me97 Engine Programming

BENZ me97 Engine programming

一、Vehicle model supported:

二、Preparation for programming:

1. Select “Local Diagnostic”, See picture 1;

2. Select MERCEDES icon , See picture 2;

3. Select “Control module programming”，See picture3；

5.Select “OK”，See picture5；

7.Select “Control unit Programming”，See picture7；

21. Prompt “Downloaded successfully”. See picture21;

You might also like