Led TV: Service Manual

Internal Use Only
North/Latin America http://aic.lgservice.com

Europe/Africa http://eic.lgservice.com
Asia/Oceania http://biz.lgservice.com
LED TV
SERVICE MANUAL
CHASSIS : LD43B/LD44B
MODEL : 42LB55** 42LB55**-Z*

42LB552V 42LB552V-TB
CAUTION
BEFORE SERVICING THE CHASSIS,
READ THE SAFETY PRECAUTIONS IN THIS MANUAL.
P/NO : MFL68003704 (1312-REV00) Printed in Korea
Downloaded from www.Manualslib.com manuals search engine

CONTENTS
CONTENTS . ............................................................................................. 2
SAFETY PRECAUTIONS ......................................................................... 3
SERVICING PRECAUTIONS ................................................................... 4
SPECIFICATION ....................................................................................... 6
ADJUSTMENT INSTRUCTION .............................................................. 10
EXPLODED VIEW .................................................................................. 17
SCHEMATIC CIRCUIT DIAGRAM ..............................................................
Copyright © LG Electronics. Inc. All rights reserved. -2- LGE Internal Use Only
Only for training and service purposes

SAFETY PRECAUTIONS
IMPORTANT SAFETY NOTICE

Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in the
Schematic Diagram and Exploded View.
It is essential that these special safety parts should be replaced with the same components as recommended in this manual to prevent
Shock, Fire, or other Hazards.
Do not modify the original design without permission of manufacturer.
General Guidance Leakage Current Hot Check (See below Figure)

Plug the AC cord directly into the AC outlet.
An isolation Transformer should always be used during the
servicing of a receiver whose chassis is not isolated from the AC Do not use a line Isolation Transformer during this check.
power line. Use a transformer of adequate power rating as this Connect 1.5 K / 10 watt resistor in parallel with a 0.15 uF capacitor
protects the technician from accidents resulting in personal injury between a known good earth ground (Water Pipe, Conduit, etc.)
from electrical shocks. and the exposed metallic parts.
Measure the AC voltage across the resistor using AC voltmeter
It will also protect the receiver and it's components from being with 1000 ohms/volt or more sensitivity.
damaged by accidental shorts of the circuitry that may be Reverse plug the AC cord into the AC outlet and repeat AC voltage
inadvertently introduced during the service operation. measurements for each exposed metallic part. Any voltage
measured must not exceed 0.75 volt RMS which is corresponds to
If any fuse (or Fusible Resistor) in this TV receiver is blown, 0.5 mA.
replace it with the specified. In case any measurement is out of the limits specified, there is
possibility of shock hazard and the set must be checked and
When replacing a high wattage resistor (Oxide Metal Film Resistor, repaired before it is returned to the customer.
over 1 W), keep the resistor 10 mm away from PCB.
Leakage Current Hot Check circuit
Keep wires away from high voltage or high temperature parts.
Before returning the receiver to the customer,
Always perform an AC leakage current check on the exposed

metallic parts of the cabinet, such as antennas, terminals, etc., to
be sure the set is safe to operate without damage of electrical
shock.
Leakage Current Cold Check(Antenna Cold Check)

With the instrument AC plug removed from AC source, connect an
electrical jumper across the two AC plug prongs. Place the AC
switch in the on position, connect one lead of ohm-meter to the AC
plug prongs tied together and touch other ohm-meter lead in turn to
each exposed metallic parts such as antenna terminals, phone
jacks, etc.
If the exposed metallic part has a return path to the chassis, the
measured resistance should be between 1 MΩ and 5.2 MΩ.
When the exposed metal has no return path to the chassis the
reading must be infinite.
An other abnormality exists that must be corrected before the
receiver is returned to the customer.

SERVICING PRECAUTIONS
CAUTION: Before servicing receivers covered by this service 2. After removing an electrical assembly equipped with ES
manual and its supplements and addenda, read and follow the devices, place the assembly on a conductive surface such as
SAFETY PRECAUTIONS on page 3 of this publication. aluminum foil, to prevent electrostatic charge buildup or expo-
NOTE: If unforeseen circumstances create conflict between the sure of the assembly.
following servicing precautions and any of the safety precautions 3. Use only a grounded-tip soldering iron to solder or unsolder
on page 3 of this publication, always follow the safety precau- ES devices.
tions. Remember: Safety First. 4. Use only an anti-static type solder removal device. Some sol-
der removal devices not classified as “anti-static” can generate
General Servicing Precautions electrical charges sufficient to damage ES devices.
1. Always unplug the receiver AC power cord from the AC power 5. Do not use freon-propelled chemicals. These can generate
source before; electrical charges sufficient to damage ES devices.
a. Removing or reinstalling any component, circuit board 6. Do not remove a replacement ES device from its protective
module or any other receiver assembly. package until immediately before you are ready to install it.
b. Disconnecting or reconnecting any receiver electrical plug (Most replacement ES devices are packaged with leads elec-
or other electrical connection. trically shorted together by conductive foam, aluminum foil or
c. Connecting a test substitute in parallel with an electrolytic comparable conductive material).
capacitor in the receiver. 7. Immediately before removing the protective material from the
CAUTION: A wrong part substitution or incorrect polarity leads of a replacement ES device, touch the protective mate-
installation of electrolytic capacitors may result in an explo- rial to the chassis or circuit assembly into which the device will
sion hazard. be installed.
2. Test high voltage only by measuring it with an appropriate CAUTION: Be sure no power is applied to the chassis or cir-
high voltage meter or other voltage measuring device (DVM, cuit, and observe all other safety precautions.
FETVOM, etc) equipped with a suitable high voltage probe. 8. Minimize bodily motions when handling unpackaged replace-
Do not test high voltage by "drawing an arc". ment ES devices. (Otherwise harmless motion such as the
3. Do not spray chemicals on or near this receiver or any of its brushing together of your clothes fabric or the lifting of your
assemblies. foot from a carpeted floor can generate static electricity suf-
4. Unless specified otherwise in this service manual, clean ficient to damage an ES device.)
electrical contacts only by applying the following mixture to the
contacts with a pipe cleaner, cotton-tipped stick or comparable General Soldering Guidelines
non-abrasive applicator; 10 % (by volume) Acetone and 90 % 1. Use a grounded-tip, low-wattage soldering iron and appropri-
(by volume) isopropyl alcohol (90 % - 99 % strength) ate tip size and shape that will maintain tip temperature within
CAUTION: This is a flammable mixture. the range or 500 °F to 600 °F.
Unless specified otherwise in this service manual, lubrication 2. Use an appropriate gauge of RMA resin-core solder composed
of contacts in not required. of 60 parts tin/40 parts lead.
5. Do not defeat any plug/socket B+ voltage interlocks with which 3. Keep the soldering iron tip clean and well tinned.
receivers covered by this service manual might be equipped. 4. Thoroughly clean the surfaces to be soldered. Use a mall wire-
6. Do not apply AC power to this instrument and/or any of its bristle (0.5 inch, or 1.25 cm) brush with a metal handle.
electrical assemblies unless all solid-state device heat sinks Do not use freon-propelled spray-on cleaners.
are correctly installed. 5. Use the following unsoldering technique
7. Always connect the test receiver ground lead to the receiver a. Allow the soldering iron tip to reach normal temperature.
chassis ground before connecting the test receiver positive (500 °F to 600 °F)
lead. b. Heat the component lead until the solder melts.
Always remove the test receiver ground lead last. c. Quickly draw the melted solder with an anti-static, suction-
8. Use with this receiver only the test fixtures specified in this type solder removal device or with solder braid.
service manual. CAUTION: Work quickly to avoid overheating the circuit
CAUTION: Do not connect the test fixture ground strap to any board printed foil.
heat sink in this receiver. 6. Use the following soldering technique.
a. Allow the soldering iron tip to reach a normal temperature
Electrostatically Sensitive (ES) Devices (500 °F to 600 °F)
Some semiconductor (solid-state) devices can be damaged eas- b. First, hold the soldering iron tip and solder the strand
ily by static electricity. Such components commonly are called against the component lead until the solder melts.
Electrostatically Sensitive (ES) Devices. Examples of typical ES c. Quickly move the soldering iron tip to the junction of the
devices are integrated circuits and some field-effect transistors component lead and the printed circuit foil, and hold it there
and semiconductor “chip” components. The following techniques only until the solder flows onto and around both the compo-
should be used to help reduce the incidence of component dam- nent lead and the foil.
age caused by static by static electricity. CAUTION: Work quickly to avoid overheating the circuit
1. Immediately before handling any semiconductor component or board printed foil.
semiconductor-equipped assembly, drain off any electrostatic d. Closely inspect the solder area and remove any excess or
charge on your body by touching a known earth ground. Alter- splashed solder with a small wire-bristle brush.
natively, obtain and wear a commercially available discharg-
ing wrist strap device, which should be removed to prevent
potential shock reasons prior to applying power to the unit
under test.

IC Remove/Replacement 3. Solder the connections.
Some chassis circuit boards have slotted holes (oblong) through CAUTION: Maintain original spacing between the replaced
which the IC leads are inserted and then bent flat against the cir- component and adjacent components and the circuit board to
cuit foil. When holes are the slotted type, the following technique prevent excessive component temperatures.
should be used to remove and replace the IC. When working with
boards using the familiar round hole, use the standard technique Circuit Board Foil Repair
as outlined in paragraphs 5 and 6 above. Excessive heat applied to the copper foil of any printed circuit
board will weaken the adhesive that bonds the foil to the circuit
Removal board causing the foil to separate from or "lift-off" the board. The
1. Desolder and straighten each IC lead in one operation by following guidelines and procedures should be followed when-
gently prying up on the lead with the soldering iron tip as the ever this condition is encountered.
solder melts.
2. Draw away the melted solder with an anti-static suction-type At IC Connections
solder removal device (or with solder braid) before removing To repair a defective copper pattern at IC connections use the
the IC. following procedure to install a jumper wire on the copper pattern
Replacement side of the circuit board. (Use this technique only on IC connec-
1. Carefully insert the replacement IC in the circuit board. tions).
2. Carefully bend each IC lead against the circuit foil pad and
solder it. 1. Carefully remove the damaged copper pattern with a sharp
3. Clean the soldered areas with a small wire-bristle brush. knife. (Remove only as much copper as absolutely necessary).
(It is not necessary to reapply acrylic coating to the areas). 2. Carefully scratch away the solder resist and acrylic coating (if
used) from the end of the remaining copper pattern.
"Small-Signal" Discrete Transistor 3. Bend a small "U" in one end of a small gauge jumper wire and
Removal/Replacement carefully crimp it around the IC pin. Solder the IC connection.
1. Remove the defective transistor by clipping its leads as close 4. Route the jumper wire along the path of the out-away copper
as possible to the component body. pattern and let it overlap the previously scraped end of the
2. Bend into a "U" shape the end of each of three leads remain- good copper pattern. Solder the overlapped area and clip off
ing on the circuit board. any excess jumper wire.
3. Bend into a "U" shape the replacement transistor leads.
4. Connect the replacement transistor leads to the corresponding At Other Connections
leads extending from the circuit board and crimp the "U" with Use the following technique to repair the defective copper pattern
long nose pliers to insure metal to metal contact then solder at connections other than IC Pins. This technique involves the
each connection. installation of a jumper wire on the component side of the circuit
board.
Power Output, Transistor Device
Removal/Replacement 1. Remove the defective copper pattern with a sharp knife.
1. Heat and remove all solder from around the transistor leads. Remove at least 1/4 inch of copper, to ensure that a hazardous
2. Remove the heat sink mounting screw (if so equipped). condition will not exist if the jumper wire opens.
3. Carefully remove the transistor from the heat sink of the circuit 2. Trace along the copper pattern from both sides of the pattern
board. break and locate the nearest component that is directly con-
4. Insert new transistor in the circuit board. nected to the affected copper pattern.
5. Solder each transistor lead, and clip off excess lead. 3. Connect insulated 20-gauge jumper wire from the lead of the
6. Replace heat sink. nearest component on one side of the pattern break to the
lead of the nearest component on the other side.
Diode Removal/Replacement Carefully crimp and solder the connections.
1. Remove defective diode by clipping its leads as close as pos- CAUTION: Be sure the insulated jumper wire is dressed so the
sible to diode body. it does not touch components or sharp edges.
2. Bend the two remaining leads perpendicular y to the circuit
board.
3. Observing diode polarity, wrap each lead of the new diode
around the corresponding lead on the circuit board.
4. Securely crimp each connection and solder it.
5. Inspect (on the circuit board copper side) the solder joints of
the two "original" leads. If they are not shiny, reheat them and
if necessary, apply additional solder.
Fuse and Conventional Resistor

Removal/Replacement
1. Clip each fuse or resistor lead at top of the circuit board hollow
stake.
2. Securely crimp the leads of replacement component around
notch at stake top.

SPECIFICATION
NOTE : Specifications and others are subject to change without notice for improvement.
1. Application range 3. Test method

This specification is applied to the LED TV used LD43B/ 1) Performance: LGE TV test method followed
LD43M/LD44B chassis. 2) Demanded other specification
- Safety : CE, IEC specification
- EMC : CE, IEC
2. Requirement for Test
Each part is tested as below without special appointment.
1) Temperature: 25 °C ± 5 °C(77 °F ± 9 °F), CST: 40 °C ± 5 °C

2) Relative Humidity: 65 % ± 10 %
3) Power Voltage
: Standard input voltage (AC 100-240 V~, 50/60 Hz)
* Standard Voltage of each products is marked by models.
4) Specification and performance of each parts are followed
each drawing and specification by part number in
accordance with BOM.
5) The receiver must be operated for about 5 minutes prior to
the adjustment.
4. Model General Specification

No. Item Specification Remarks
1 Market EU(PAL Market-37Countries) DTV & Analog (Total 37 countries)
DTV (MPEG2/4, DVB-T) :37 countries
UK/Italy/Germany/France/Spain/Sweden/Finland/Netherlands/
Belgium/Luxemburg/ Greece/Denmark/Czech/Austria /Hun-
gary/Swiss/Croatia/TurkeyNorway/Slovenia/Poland/Ukraine/
Portugal/Ireland/Morocco/Latvia/Estonia/Lithania/Rumania/
Bulgaria/Russia/SlovakiaBosnia/Serbia/Albania/Kazakhstan/
Belarus
DTV (MPEG2/4, DVB-T2): 8 countries

UK/Denmark/Sweden/Finland/Norway/Ireland/Ukraine/Kaza-
khstan
DTV (MPEG2/4, DVB-C): 37 countries

UK/Italy/Germany/France/Spain/Sweden/Finland/Netherlands/
Belgium/Luxemburg/ Greece/Denmark/Czech/Austria /Hun-
gary/Swiss/Croatia/TurkeyNorway/Slovenia/Poland /Ukraine/
Portugal/Ireland/Morocco/Latvia/Estonia/Lithania/Rumania/
Bulgaria/Russia/SlovakiaBosnia/Serbia/Albania/Kazakhstan/
Belarus
DTV (MPEG2/4,DVB-S): 29 countries

Italy/Germany/France/Spain/Netherlands/ Belgium/Luxemburg/
Greece/Czech/Austria /Hungary/Swiss/Croatia/Turkey/Slove-
nia/Poland/Portugal/ Morocco/Latvia/Estonia/Lithania/Rumania/
Bulgaria/Russia/Slovakia/Bosnia/Serbia/Albania/Belarus
Supported satellite : 22 satellites

HISPASAT 1C/1D, ATLANTIC BIRD 2, NILESAT 101/102,
ATLANTIC BIRD 3, AMOS 2/3, THOR 5/6, IRIUS 4, EUTEL-
SAT-W3A, EUROBIRD 9A, EUTELSAT-W2A, HOTBIRD 6/8/9,
EUTELSAT-SESAT, ASTRA 1L/H/M/KR, ASTRA 3A/3B, BADR
4/6, ASTRA 2D, EUROBIRD 3, EUTELSAT-W7, HELLASSAT
2, EXPRESS AM1, TURKSAT 2A/3A, INTERSAT10

No. Item Specification Remarks
Analogue TV
1) PAL-BG Analogue TV : (RF) VHF: E2 to E12, UHF : E21 to E69
2) PAL-DK (CATV) S1 to S20, HYPER: S21 to S47
3) PAL-I/I’
4) SECAM-BG Digital TV : VHF, UHF
5) SECAM-DK
2 Broadcasting system 6) SECAM L/L’ Satellite TV : VHF, UHF,
C-Band, Ku-Band
Digital TV
1) DVB-T/C/T2 * DVB-T2 ( T2 model only support )
Satellite Digital TV * DVB-S/S2 (Satellite model only support )

1) DVB-T/C/S2
► DVB-T
- Guard Interval(Bitrate_Mbit/s) : 1/4, 1/8, 1/16, 1/32
- Modulation : Code Rate
QPSK : 1/2, 2/3, 3/4, 5/6, 7/8
16-QAM : 1/2, 2/3, 3/4, 5/6, 7/8
64-QAM : 1/2, 2/3, 3/4, 5/6, 7/8
► DVB-T2
- Guard Interval(Bitrate_Mbit/s)
: 1/4, 1/8, 1/16, 1/32, 1/128, 19/128, 19/256,
- Modulation : Code Rate
QPSK : 1/2, 2/5, 2/3, 3/4, 5/6
Analog : Upper Heterodyne 16-QAM : 1/2, 2/5, 2/3, 3/4, 5/6
3 Receiving system Digital : COFDM, QAM 64-QAM : 1/2, 2/5, 2/3, 3/4, 5/6
256-QAM : 1/2, 2/5, 2/3, 3/4, 5/6
► DVB-C
- Symbolrate : 4.0Msymbols/s to 7.2Msymbols/s
- Modulation : 16QAM, 64-QAM, 128-QAM and 256-QAM
► DVB-S/S2
- symbolrate
DVB-S2 (8PSK / QPSK) : 2 ~ 45Msymbol/s
DVB-S (QPSK) : 2 ~ 45Msymbol/s
- viterbi
DVB-S mode : 1/2, 2/3, 3/4, 5/6, 7/8
DVB-S2 mode : 1/2, 2/3, 3/4, 3/5, 4/5, 5/6, 8/9, 9/10
4 Scart Jack (1EA) PAL, SECAM Scart 1 Jack is Full scart and support RF-OUT(analog).
Video Input RCA
4 System : PAL, SECAM, NTSC, PAL60
Component & AV (PAL, SECAM, NTSC)
5
Common port (1EA) Component Input
(Y/Cb/Cr, Y/Pb/Pr)
7 HDMI Input (2EA) HDMI1/2-DTV Support HDCP
8 Audio Input (1EA) Component & AV Component & AV’s audio input is used by common port.
9 SDPIF out (1EA) SPDIF out
Antenna, AV1, AV2, Component,
10 Earphone out (1EA) LB62 &LB56 Series
HDMI1, HDMI2
11 USB (1EA) EMF, DivX HD, For SVC (download) JPEG, MP3, DivX HD
CI : U
K, Finland, Denmark, Norway, Sweden, Russia, Spain,
DVB-T Ireland, Luxemburg, Belgium, Netherland
CI+ : France(Canal+), Italy(DGTVi)
12 DVB CI : Switzerland, Austria, Slovenia, Hungary, Bulgaria
DVB-C CI+ : S
witzerland(UPC,Cablecom), Netherland(Ziggo),
Germany(KDG,CWB), Finland(labwise)
DVB-S CI + : Germany(Astra HD+ )
LB62 : for DLNA
13 Ethernet (1EA) DLNA(Wired, DMP only)
T2 Model ( LB62, LB56, LB55 ) : for MHEG

5. Video resolutions (2D)
5.1. Component Input (Y, CB/PB, CR/PR)
No. Resolution H-freq(kHz) V-freq(Hz) Pixel clock(MHz) Proposed
1 720*576 15.625 50.00 13.5 SDTV ,DVD 576I
2 720*480 15.73 60.00 13.5135 SDTV ,DVD 480I
3 720*480 15.73 59.94 13.50 SDTV ,DVD 480I
4 720*576 31.25 50.00 27.00 SDTV 576P
5 720*480 31.50 60.00 27.027 SDTV 480P
6 720*480 31.47 59.94 27.00 SDTV 480P
7 1280*720 37.50 50.00 74.25 HDTV 720P
8 1280*720 45.00 60.00 74.25 HDTV 720P
9 1280*720 44.96 59.94 74.176 HDTV 720P
10 1920*1080 28.125 50.00 74.25 HDTV 1080I
11 1920*1080 33.75 60.00 74.25 HDTV 1080I
12 1920*1080 33.72 59.94 74.176 HDTV 1080I
13 1920*1080 56.25 50.00 148.50 HDTV 1080P
14 1920*1080 67.50 60.00 148.50 HDTV 1080P
15 1920*1080 67.432 59.94 148.352 HDTV 1080P
16 1920*1080 27.00 24.00 74.25 HDTV 1080P
17 1920*1080 26.97 23.94 74.176 HDTV 1080P
18 1920*1080 33.75 30.00 74.25 HDTV 1080P
19 1920*1080 33.71 29.97 74.176 HDTV 1080P
5.2. HDMI Input(PC/DTV)

No. Resolution H-freq(kHz) V-freq.(Hz) Pixel clock(MHz) Proposed Remark
PC(DVI) DDC
1 640*350 31.468 70.09 25.17 EGA X
2 720*400 31.469 70.08 28.32 DOS O
3 640*480 31.469 59.94 25.17 VESA(VGA) O
4 800*600 37.879 60.31 40.00 VESA(SVGA) O
5 1024*768 48.363 60.00 65.00 VESA(XGA) O
6 1152*864 54.348 60.053 80.00 VESA O
7 1360*768 47.712 60.015 85.50 VESA (WXGA) O
8 1280*1024 63.981 60.020 108.0 VESA (SXGA) O FHD only
9 1920*1080 67.50 60.00 148.5 HDTV 1080P O FHD only
DTV
1 720*480 31.47 59.94 27.00 SDTV 480P
2 720*480 31.50 60.00 27.027 SDTV 480P
3 720*576 31.250 50.00 27.00 SDTV 576P
4 1280*720 37.50 50.00 74.25 HDTV 720P
5 1280*720 45.00 60.00 74.25 HDTV 720P
6 1280*720 44.96 59.94 74.176 HDTV 720P
7 1920*1080 28.125 50.00 74.25 HDTV 1080I
8 1920*1080 33.75 60.00 74.25 HDTV 1080I
9 1920*1080 33.72 59.94 74.176 HDTV 1080I
10 1920*1080 56.250 50.00 148.50 HDTV 1080P
11 1920*1080 67.50 60.00 148.50 HDTV 1080P
12 1920*1080 67.432 59.94 148.352 HDTV 1080P
13 1920*1080 27.00 24.00 74.25 HDTV 1080P
14 1920*1080 26.97 23.976 74.176 HDTV 1080P
15 1920*1080 33.75 30.00 74.25 HDTV 1080P

6. Video resolutions (3D)
6.1. HDMI Input
No. Resolution H-freq(kHz) V-freq(Hz) Pixel clock(MHz) Proposed 3D input proposed mode
1. 1920*1080 53.95 / 54 23.98 / 24 148.35/148.5 HDTV 1080P Frame packing
2. 1280*720 89.9 / 90 59.94/60 148.35/148.5 HDTV 720P Frame packing
3. 1280*720 75 50 148.5 HDTV 720P Frame packing
4 1920*1080 67.5 60 148.5 HDTV 1080P Side by Side(half), Top and bottom
5 1920*1080 56.3 50 148.5 HDTV 1080P Side by Side(half), Top and bottom
6 1280*720 45 60 74.25 HDTV 720P Side by Side(half), Top and Bottom
7 1280*720 37.5 50 74.25 HDTV 720P Side by Side(half), Top and Bottom
8 1920*1080 33.7 60 74.25 HDTV 1080i Side by Side(half), Top and Bottom
9 1920*1080 28.125 50 74.25 HDTV 1080i Side by Side(half), Top and Bottom
10 1920*1080 27 24 74.25 HDTV 1080P Side by Side(half), Top and Bottom
11 1920*1080 33.7 30 89.1 HDTV 1080P Side by Side(half), Top and Bottom
6.2. RF 3D Input(DTV)
No. Resolution H-freq(kHz) V-freq.(Hz) Pixel clock(MHz) Proposed 3D input proposed mode
1. 1280*720 37.500 50 74.25 HDTV 720P Side by Side, Top & Bottom
2. 1920*1080 28.125 50 74.25 HDTV 1080I Side by Side, Top & Bottom
6.3. USB Input

Side by Side, Top & Bottom **support
1. 1920*1080 33.75 30.000 74.25 HDTV 1080P
MPO(Photo)
6.4. DLNA Input

1. 1920*1080 33.75 30 74.25 HDTV 1080p Side by Side, Top & Bottom
6.5. 3D Input mode

No. Side by Side Top & Bottom Single Frame Sequential Frame Packing

ADJUSTMENT INSTRUCTION
1. Application Range (4) Click "Connect" tab. If "Can't" is displayed, check connection
between computer, jig, and set.
This specification sheet is applied to all of the LED TV with
LD43B/LD43M/LD44B chassis.
(2) (3)
2. Designation
(1) The adjustment is according to the order which is designated
and which must be followed, according to the plan which
can be changed only on agreeing.
(2) Power adjustment : Free Voltage.
(3) Magnetic Field Condition: Nil.
(4) Input signal Unit: Product Specification Standard.
(5) Reserve after operation : Above 5 Minutes (Heat Run) Please Check the Speed :
Temperature : at 25 °C ± 5 °C To use speed between
Relative humidity : 65 ± 10 % from 200KHz to 400KHz
Input voltage : 220 V, 60 Hz
(6) Adjustment equipments: Color Analyzer(CA-210 or CA-110), (5) Click "Auto" tab and set as below.
DDC Adjustment Jig, Service remote control. (6) Click "Run".
(7) Push the "IN STOP" key - For memory initialization. (7) After downloading, check "OK" message.
Case1 : Software version up

(4)
1. After downloading S/W by USB , TV set will reboot
automatically. filexxx.bin
2. Push “In-stop” key. (5)
3. Push “Power on” key.
4. Function inspection
5. After function inspection, Push “In-stop” key. (7)...........OK
Case2 : Function check at the assembly line
1. When TV set is entering on the assembly line, Push
“In-stop” key at first. (6)
2. Push “Power on” key for turning it on.
→ If you push “Power on” key, TV set will recover
channel information by itself.
3. After function inspection, Push “In-stop” key.
* USB DOWNLOAD
(1) Put the USB Stick to the USB socket.
(2) Automatically detecting update file in USB Stick.
3. Main PCB check process - If your downloaded program version in USB Stick is Low,
▪ APC - After Manual-Insert, executing APC it didn't work. But your downloaded version is High, USB
data is automatically detecting.
(3) Show the message "Copying files from memory".
* Boot file Download (4) Updating is starting.
(1) Execute ISP program "Mstar ISP Utility" and then click
"Config" tab.
(2) Set as below, and then click "Auto Detect" and check "OK"
message.
If "Error" is displayed, check connection between computer,
jig, and set.
(3) Click "Read" tab, and then load download file(XXXX.bin)
by clicking "Read". (5) Updating Completed, The TV will restart automatically in 5
seconds.
(1) (6) If your TV is turned on, check your updated version and
Tool option. (explain the Tool option, next stage)
filexxx.bin * If downloading version is more high than your TV have, TV
can lost all channel data. In this case, you have to channel
recover. if all channel data is cleared, you didn’t have a DTV/
ATV test on production line.
Copyright © LG Electronics. Inc. All rights reserved. - 10 - LGE Internal Use Only

* After downloading, have to adjust Tool Option again. 3.3. EDID data
(1) Push "IN-START" key in service remote control. (1) HD HDMI EDID data (2D model)
(2) Select "Tool Option 1" and push "OK" key. 0 1 2 3 4 5 6 7 8 9 A B C D E F
(3) Punch in the number. (Each model has their number) 00 00 FF FF FF FF FF FF 00 1E 6D a b
(4) Completed selecting Tool option. 10 c 01 03 80 A0 5A 78 0A EE 91 A3 54 4C 99 26
20 0F 50 54 A1 08 00 31 40 45 40 61 40 71 40 01 01
30 01 01 01 01 01 01 66 21 50 B0 51 00 1B 30 40 70
3.1. ADC Process 40 36 00 40 84 63 00 00 1E 64 19 00 40 41 00 26 30
* If ADC processes as OTP, There is no need to proceed 50 18 88 03 06 40 84 63 00 00 18 00 00 00 FD 00 3A
internal ADC. 60 3E 1E 53 10 00 0A 20 20 20 20 20 20 d
- Enter Service Mode by pushing "ADJ" key, 70 d 01 e
- Enter Internal ADC mode by pushing "►" key at "8. ADC 80 02 03 22 F1 4E 10 1F 04 93 05 14 03 02 12 20 21
Calibration". 90 22 15 01 26 15 07 50 09 57 07 f
A0 80 1E 01 1D 80 18 71 1C 16 20 58 2C 25 00 A0 5A
EZ ADJUST ADC Calibration
B0 00 00 00 9E 01 1D 00 72 51 D0 1E 20 6E 28 55 00
0. Tool Option1 ADC Comp 480i
1. Tool Option2
OK
C0 20 C2 31 00 00 1E 8C 0A D0 8A 20 E0 2D 10 10 3E
ADC Comp 1080p OK
2. Tool Option3 ADC Type ◄ OTP ► D0 96 00 A0 5A 00 00 00 18 02 3A 80 18 71 38 2D 40
3. Tool Option4
Start Reset
E0 58 2C 45 00 A0 5A 00 00 00 1E 00 00 00 00 00 00
4. Tool Option5
5. Tool Option Commercial F0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e
6. Country Group
7. Area Option
8.ADC Calibration ►
(2) FHD HDMI EDID data (2D model)
9. White Balance 0 1 2 3 4 5 6 7 8 9 A B C D E F
10. 10 Point WB
11. Test Pattern
00 00 FF FF FF FF FF FF 00 1E 6D a b
12 EDID D/L 10 c 01 03 80 A0 5A 78 0A EE 91 A3 54 4C 99 26
13. Sub B/C
20 0F 50 54 A1 08 00 31 40 45 40 61 40 71 40 81 80
14. Ext. Input Adjust
30 01 01 01 01 01 01 02 3A 80 18 71 38 2D 40 58 2C
40 45 00 A0 5A 00 00 00 1E 66 21 50 B0 51 00 1B 30
<Caution> U sing "P-ONLY" key of the Adjustment remote 50 40 70 36 00 A0 5A 00 00 00 1E 00 00 00 FD 00 3A
control, power on TV. 60 3E 1E 53 10 00 0A 20 20 20 20 20 20 d
70 d 01 e
* ADC Calibration Protocol (RS232) 80 02 03 22 F1 4E 10 9F 04 13 05 14 03 02 12 20 21
NO Item CMD 1 CMD 2 Data 0 90 22 15 01 26 15 07 50 09 57 07 f
Enter Adjust Adjust When transfer the ‘Mode In’, A0 f 01 1D 80 18 71 1C 16 20 58 2C 25 00 20 C2
A A 0 0
MODE ‘Mode In’ Carry the command. B0 31 00 00 9E 01 1D 00 72 51 D0 1E 20 6E 28 55 00
ADC Automatically adjustment C0 20 C2 31 00 00 1E 02 3A 80 18 71 38 2D 40 58 2C
ADC adjust A D 1 0
Adjust (The use of a internal pattern)
D0 45 00 A0 5A 00 00 00 1E 01 1D 00 BC 52 D0 1E 20
E0 B8 28 55 40 C4 8E 21 00 00 1E 00 00 00 00 00 00
F0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e
Adjust Sequence
▪ aa 00 00 [Enter Adjust Mode] (3) FHD HDMI EDID data (3D model)
▪ xb 00 40 [Component Input] 0 1 2 3 4 5 6 7 8 9 A B C D E F
▪ ad 00 10 [Adjust 480i & 1080p Comp] 00 00 FF FF FF FF FF FF 00 1E 6D a b
▪ aa 00 90 End Adjust mode 10 c 01 03 80 A0 5A 78 0A EE 91 A3 54 4C 99 26
* Required equipment : Adjustment remote control. 20 0F 50 54 A1 08 00 31 40 45 40 61 40 71 40 81 80
30 01 01 01 01 01 01 02 3A 80 18 71 38 2D 40 58 2C
3.2. EDID Download 40 45 00 A0 5A 00 00 00 1E 66 21 50 B0 51 00 1B 30
▪ After enter Service Mode by pushing "ADJ" key. 50 40 70 36 00 A0 5A 00 00 00 1E 00 00 00 FD 00 3A
60 3E 1E 53 10 00 0A 20 20 20 20 20 20 d
▪ Enter EDID D/L menu.
70 d 01 e
▪ Enter "START" by pushing "OK" key.
80 02 03 33 F1 4E 10 9F 04 13 05 14 03 02 12 20 21
EZ ADJUST EDID D/L
0. Tool Option1 HDMI1 NG 90 22 15 01 26 15 07 50 09 57 07 f
1. Tool Option2 HDMI2 NG A0 80 1E 20 C0 0E 01 40 0A 0F 08 10 18 10 98 10 58
2. Tool Option3 Start Reset
3. Tool Option4
B0 10 38 10 01 1D 80 18 71 1C 16 20 58 2C 25 00 20
4. Tool Option5 C0 C2 31 00 00 9E 01 1D 00 72 51 D0 1E 20 6E 28 55
5. Tool Option Commercial D0 00 20 C2 31 00 00 1E 02 3A 80 18 71 38 2D 40 58
6. Country Group
7. Area Option
E0 2C 45 00 A0 5A 00 00 00 1E 01 1D 00 BC 52 D0 1E
8. ADC Calibration F0 20 B8 28 55 40 C4 8E 21 00 00 1E 00 00 00 00 e
9. White Balance
10. 10 Point WB
11. Test Pattern
12. EDID D/L ►
13. Sub B/C
14. Ext. Input Adjust
<Caution> Never connect HDMI cable when EDID downloaded.

(3) Detail EDID Options are below
a. Product ID
4. Total Assembly line process
4.1. White Balance adjustment
MODEL NAME HEX EDID Table DDC Function ▪ W/B Equipment condition
HD/FHD Model 0001 01 00 Analog/Digital CA210 : LED -> CH14, Test signal: Inner pattern(80IRE)
▪ Above 5 minutes H/run in the inner pattern. (“power on” key
b. Serial No: Controlled on production line. of adjust remote control)
c. Month, Year: ▪ If it is executed W/B adjustment in 2~3 minutes H/run, it is
ex) Week : '01' -> '01' adjusted by Target data.
Year : '2014' -> '18' fix Mode Temp Coordinate spec Target
d. Model Name(Hex): X=0.271 (±0.002) X=0.278
cf) TV set’s model name in EDID data is below. Cool 13,000 K
Y=0.270 (±0.002) Y=0.280
Model name MODEL NAME(HEX) X=0.285 (±0.002) X=0.293
Medium 9,300 K
LG TV 00 00 00 FC 00 4C 47 20 54 56 0A 20 20 20 20 20 20 20 (LG TV) Y=0.293 (±0.002) Y=0.299
X=0.313 (±0.002) X=0.320
e. Checksum: Changeable by total EDID data. Warm 6,500 K
Y=0.329 (±0.002) Y=0.339
HD FHD(2D) FHD(3D)
EDID C/S data ▪ Normal line(LGD/CMI, March ~ December for Gumi, Global)
HDMI HDMI HDMI
Cool Medium Warm
Block 0 75 41 41 Aging time
Check sum NetCase4 X y x y x y
5B (HDMI1) 25 (HDMI1) 23 (HDMI1) (Min)
(Hex) Block 1 271 270 285 293 313 329
4B (HDMI2) 15 (HDMI2) 13 (HDMI2)
1 0-2 281 287 295 310 320 342
2 3-5 280 285 294 308 319 340
f. Vendor Specific(HDMI)
3 6-9 278 284 292 307 317 339
INPUT Model name(HEX)_2D Model name(HEX)_3D
4 10-19 276 281 290 304 315 336
HDMI1 67030C001000801E 78030C001000801E 5 20-35 275 277 289 300 314 332
HDMI2 67030C002000801E 78030C002000801E 6 36-49 274 274 288 297 313 329
7 50-79 273 272 287 295 312 327
8 80-119 272 271 286 294 311 326
9 Over 120 271 270 285 293 310 325
3.4. Function Check ▪ Normal line(LGD/CMI, January ~ February for Gumi, Apply
- Check display and sound not Cinema Screen)
■ Check Input and Signal items. Cool Medium Warm
1) TV Aging time
NetCase4 X y x y x y
2) AV (SCART / CVBS) (Min)
3) COMPONENT (480i) 271 270 285 293 313 329
4) HDMI 1 0-2 283 292 297 315 322 347
* Display and Sound check is executed by Remote control. 2 3-5 282 290 296 313 321 345
3 6-9 280 288 294 311 319 343
<Caution> 4 10-19 277 284 291 307 316 339
Not to push the INSTOP key after completion if the function 5 20-35 275 279 289 302 314 334
inspection. 6 36-49 274 275 288 298 313 330
7 50-79 273 272 287 295 312 327
8 80-119 272 271 286 294 311 326
9 Over 120 271 270 285 293 310 325
▪ Aging chamber(LGD/CMI)
Cool Medium Warm
Aging time
NetCase4 X y x y x y
(Min)
271 270 285 293 313 329
1 0-5 280 285 294 308 319 340
2 6-10 276 280 290 303 315 335
3 11-20 272 275 286 298 311 330
4 21-30 269 272 283 295 308 327
5 31-40 267 268 281 291 306 323
6 41-50 266 265 280 288 305 320
7 51-80 265 263 279 286 304 318
8 81-119 264 261 278 284 303 316
9 Over 120 264 260 278 283 303 315

▪ Use only AUO/Sharp/CSOT(Cool temp Spec is 13000 K) * Manual W/B process using adjust Remote control.
Cool Medium Warm ▪ After enter Service Mode by pushing "ADJ" key,
X y x y x y ▪ E nter White Balance by pushing " ► " key at "9. White
spec 271 270 285 293 313 329 Balance".
EZ ADJUST
target 275 276 289 299 317 335
0. Tool Option1
Whit Balance
1. Tool Option2
2. Tool Option3 Color Temp. ◄ Cool ►
▪ W/B information 3. Tool Option4 R-Gain 172
G-Gain 172
Model information W/B information 4. Tool Option5
5. Tool Option Commercial B-Gain 192
Model Module Panel Backlight Type Using W/B table 6. Country Group R-Cut 64
7. Area Option G-Cut 64
All All All Direct LED O 8. ADC Calibration B-Cut 64
9. White Balance Test-Pattern ON
10. 10 Point WB Backlight 100
Reset To Set
* Connecting picture of the measuring instrument 11. Test Pattern
12 EDID D/L
(On Automatic control) 13. Sub B/C
Inside PATTERN is used when W/B is controlled. Connect to 14. Ext. Input Adjust
auto controller or push Adjustment R/C P-ONLY → Enter the

mode of White-Balance, the pattern will come out. * CASE Cool Mode
First adjust the coordinate far away from the target
value(x, y).B.
1) x, y > target
Full White Pattern CA-210
2) x, y < target
COLOR 3) x >target, y < target
ANALYZER
TYPE : CA-210 4) x < target, y > target
-E very 4 case have to fit y value by adjusting B Gain
and then fit x value by adjusting R-Gain.
RS-232C Communication - In this case, increasing/decreasing of B Gain and R
Gain can be adjusted.
* Auto-control interface and directions How to adjust

(1) Adjust in the place where the influx of light like floodlight 1) In case G gain more than 172
around is blocked. (illumination is less than 10 lux). Adjust R Gain and B Gain less than 192
(2) Adhere closely the Color analyzer(CA210) to the module 2) If the G gain value be adjusted down to 172
less than 10 cm distance, keep it with the surface of the One of the R/B Gain is 254
Module and Color analyzer's prove vertically.(80° ~ 100°). 3) If G Gain is 172 , More than one of R/B Gain is to be
(3) Aging time between 192~254
- After aging start, keep the power on (no suspension of
power supply) and heat-run over 5 minutes. * CASE Medium / Warm
- Using 'no signal' or 'POWER ONLY' or the others, check First adjust the coordinate far away from the target
the back light on. value(x, y).
1) x, y > target
▪ Auto adjustment Map(using RS-232C to USB cable) i) Decrease the R, G.
RS-232C COMMAND 2) x, y < target
[CMD ID DATA] i) First decrease the B gain,
Wb 00 00 White Balance Start ii) Decrease the one of the others.
Wb 00 ff White Balance End 3) x > target, y < target
RS-232C COMMAND CENTER i) First decrease B, so make y a little more than the target.
[CMD ID DATA] (DEFAULT) ii) Adjust x value by decreasing the R
MIN MAX
4) x < target, y > target
Cool Mid Warm Cool Mid Warm
i) First decrease B, so make x a little more than the target.
R Gain jg Ja jd 00 172 192 192 254 ii) Adjust x value by decreasing the G
G Gain jh Jb je 00 172 192 192 192
B Gain ji Jc jf 00 192 192 172 254 * After you finished all adjustments, Press "In-start" key and
compare Tool option and Area option value with its BOM, if
R Cut 64 64 64 128
it is correctly same then unplug the AC cable. If it is not
G Cut 64 64 64 128 same, then correct it same with BOM and unplug AC cable.
B Cut 64 64 64 128 For correct it to the model's module from factory Jig model.
* P ush the "IN STOP" key after completing the function
<Caution> inspection. And Mechanical Power Switch must be set
Color Temperature : COOL, Medium, Warm. “ON”.
One of R Gain/G Gain/ B Gain should be kept on 0xC0, and
adjust other two lower than C0.(When R/G/B Gain are all
C0, it is the FULL Dynamic Range of Module)

4.2. 3D function test 4.4. MHL Test
(Pattern Generator MSHG-600, MSPG-6100[Support HDMI1.4]) (1) Turn on TV
* HDMI mode NO. 872 , pattern No.83 (2) Select HDMI2 mode using input Menu.
(1) Please input 3D test pattern like below. (3) Set MHL Zig(M1S0D3617) using MHL input, output and
power cord.
(4) Connect HDMI cable between MHL Zig and HDMI4 port.
(2) When 3D OSD appear automatically , then select OK key.
Result) I f, The LED light is green and the Module shows

normal stream → OK, Else → NG
4.5. Outgoing condition Configuration

■ When pressing IN-STOP key by SVC remocon, Red LED
(3) Don't wear a 3D Glasses, Check the picture like below. are blinked alternatively. And then automatically turn off.
(Must not AC power OFF during blinking)
4.3. IR emitter inspection

(1) Start 3D pattern inspection.
(2) If IR emitter signal is correctly received to IR receiver, the
lamp of IR tester turns on.

5. HI-POT Test 6.2. Command Set
5.1. HI-POT auto-check preparation Adjust mode CMD(hex) LENGTH(hex) Description
- Check the POWER cable and SIGNAL cable insertion condition EEPROM WRITE A0h 84h+n n-bytes Write (n = 1~16)
* Description
5.2. HI-POT auto-check FOS Default write : <7mode data> write
(1) Pallet moves in the station. (POWER CORD / AV CORD is Vtotal, V_Frequency, Sync_Polarity, Htotal, Hstart, Vstart, 0,
tightly inserted) Phase
Data write : Model Name and Serial Number write in EEPROM,.
(2) Connect the AV JACK Tester.
(3) Controller (GWS103-4) on.
(4) HI-POT test (Auto) 6.3. Method & notice
- If Test is failed, Buzzer operates. (1) Serial number D/L is using of scan equipment.
- If Test is passed, GOOD Lamp on and move to next proc- (2) S etting of scan equipment operated by Manufacturing
ess automatically. Technology Group.
(3) Serial number D/L must be conformed when it is produced in
production line, because serial number D/L is mandatory by
5.3. Checkpoint D-book 4.0.
(1) Test voltage
- Touchable Metal : 3 KV / min at 100 mA * Manual Download(Model Name and Serial Number)
- SIGNAL : 3KV / min at 100 mA If the TV set is downloaded by OTA or Service man, sometimes
(2) TEST time: 1 second. (case : mass production ) model name or serial number is initialized.(Not always)
(3) TEST POINT There is impossible to download by bar code scan, so It need
- Touchable Metal => LIVE & NEUTRAL : Touchable Metal. Manual download.
- SIGNAL => LIVE & NEUTRAL : SIGNAL. 1) Press the "Instart" key of Adjustment remote control.
2) Go to the menu "6.Model Number D/L" like below photo.
3) Input the Factory model name or Serial number like photo.
6. Model name & Serial number D/L

▪ Press "Power on" key of service remote control.
(Baud rate : 115200 bps)
▪ Connect RS232 Signal Cable to USB Jack.
▪ Write Serial number
▪ Must check the serial number at the Diagnostics of SET UP menu.
(Refer to below).
4) Check the model name Instart menu. → Factory name displayed.

ex 47LB560V-ZA)
5) Check the Diagnostics.(DTV country only) → Buyer model
displayed.(ex 47LB560V-ZA)
6.1. Signal Table

CMD LENGTH ADH ADL DATA_1 ... Data_n CS DELAY
CMD : A0h
LENGTH : 85~94h (1~16 bytes)
ADH : EEPROM Sub Address high (00~1F)
ADL : EEPROM Sub Address low (00~FF)
Data : Write data
CS : CMD + LENGTH + ADH + ADL + Data_1 +...+ Data_n
Delay : 20ms

7. MAC Address & CI+ key download 7.2. LAN Inspection
7.1 MAC Address 7.2.1. Equipment & Condition
▪ Each other connection to LAN Port of IP Hub and Jig
7.1.1 Equipment & Condition
▪ Play file : Serial.exe
▪ MAC Address edit
▪ Input Start / End MAC address
7.1.2 Download method

(1) Communication Prot connection
7.2.2. LAN inspection solution

▪ LAN Port connection with PCB
▪ Network setting at MENU Mode of TV
▪ Setting automatic IP
Connection: PCBA(USB Port) → USB to Serial Adapter(UC-
▪ Setting state confirmation
232A) → RS-232C cable → PC(RS-232C port)
-> If automatic setting is finished, you confirm IP and MAC
* Caution: L
J21* chassis support only UC-232A driver. (only
Address.
use this one.)
(2) MAC Address & CI+ Key Download

▪ Set CI+ Key path Directory at Start Mac & CI+ Download
Programme
▪ Com 1,2,3,4 and 115200(Baudrate)
7.3. LAN PORT INSPECTION(PING TEST)

GP4_LOW Connect SET -> LAN port == PC -> LAN Port
SET PC
7.3.1. Equipment setting

(1) Play the LAN Port Test PROGRAM.
(2) Input IP set up for an inspection to Test Program.
*IP Number : 12.12.2.2
▪ Port connection button click(1)
▪ Push the (2) MAC Address write. 7.3.2. LAN PORT inspection (PING TEST)
▪ At success Download, check the OK (3) (1) Play the LAN Port Test Program.
▪ Start CI+ Key Download, Push the (4) (2) Connect each other LAN Port Jack.
▪ Check the OK or NG (3) Play Test (F9) button and confirm OK Message.
(4) Remove LAN cable.

EXPLODED VIEW
IMPORTANT SAFETY NOTICE
Many electrical and mechanical parts in this chassis have special safety-related characteristics. These
parts are identified by in the Schematic Diagram and EXPLODED VIEW.
It is essential that these special safety parts should be replaced with the same components as
recommended in this manual to prevent X-RADIATION, Shock, Fire, or other Hazards.
Do not modify the original design without permission of manufacturer.
500
502
501
400
900
420
410
521
540
121
530
120
LV1
820
Set + Stand
A10
AW1
A2
200

LD43B

L14 POWER BLOCK (POWER DETECT 2)
+24V +12V +3.5V_POWER_DET

OLD_18PIN +3.5V_ST
FROM LIPS or POWER B/D P401-*1

SMAW200-H18S1
R435
100K PD_+3.5V
Power_DET PANEL_VCC
+3.5V_ST OPT OPT R454-*1 OPT +12V PANEL_VCC
R457 R430 R432 300
Q401 R438
8.2K 2.7K 0
1% 5% 5% 4.7K
MMBT3906(NXP) PWR ON 1 2 DRV ON 1%
IC401
3.5V 3 4 PDIM#1 APX803D29
R454 L408
3.5V 5 6 3.5V 100 5% Q405
1 3 OPT VCC RESET UBW2012-121F
GND PDIM#2 3 2 POWER_DET DMP2130L
R412 7 8 120OHM
R406
D
10K 2 33K 24V 9 10 24V C415 1
R431 C422
+3.5V_ST GND 11 12 GND 0.1uF 1.2K GND OPT
R404 16V POWER_DET_RESET 0.1uF C425 R445 C427 R451 R452
12V 13 14 12V 1% 10uF 5.6K 5.6K
4.7K 0.1uF 33K G
12V 15 16 N.C 25V 16V
OPT OPT
R400 GND 17 18 GND +3.5V_POWER_DET R436
10K C Q400 +24V
100K
R402 R446
10K B MMBT3904(NXP)
12K
RL_ON 19
OPT
OPT OPT
R401 R455 R427 R458 IC402
E +3.3V_Normal 27K 0 APX803D29 OPT R442 C
10K 0 R437
1% 5% 100 5% 10K B Q403
OPT VCC 3 2 RESET PANEL_CTL
R456 MMBT3904(NXP)
0 +3.5V_ST OPT 1
R420 OPT R441 E
1K C413 R428 GND 10K
ZD404 0.1uF 5.1K
5V R419 16V 1%
100 R426
+3.5V_POWER_DET NEW_18PIN 10K
P401
SMAW200-H18S5
C
R425 Ready - Dual Power Det Power Detect activity
B 10K
L400 INV_CTL
CB2012PK501T
+3.5V_ST Detect Valtage Now is Use Circuit Designator FET_2.5V_DIODE
E Q402
PWR ON 1 2 DRV ON MMBT3904(NXP) Q406-*1
L401
C407
10uF
10V
C400
1uF
10V
ZD400
5V
CB2012PK501T 3.5V
3.5V
3 4 PDIM#1
3.5V
PWM_DIM Power Detect +3.5V R432, R454-*1, R438 +3.3V_Normal DMP2130L
D
2012 1005 5 6
OPT GND PDMI#2
L402 7 8 PWM1 * Notice Power Detect +12V O R430, R431, R454
MLB-201209-0120P-N2 24V 24V
+24V 9 10 PWM_DIM_PULL_DOWN PWM2_2CH_POWER
OPT
- Applying all inch models for LCD L14 +3.5V_ST +3.3V_Normal
G
+24V_CAP GND GND R424 R423
C401 11 12
100
R467 - Dual Power Det is used Power Detect +24V R457, R454
C432 12V 12V 3.9K 1K
4.7uF 0.1uF 13 14 for detecting two kinds of voltage
50V 12V NC FET_2.5V_AOS
50V 15 16
Q406 L410
3216 GND 17 18 GND
L403 AO3435 BLM18PG121SN1D
MLB-201209-0120P-N2
+12V
D
+12V_CAP
C433
4.7uF
C402
0.1uF
19
+1.10V_VDDC
.
C428 C429 C430
G
16V 16V R443 R447 ZD402
+3.5V_ST 10K 22K 2.2uF 0.1uF 22uF
3216 5V
IC403 +3.3V_Normal 10V 16V 10V
L406 TPS5432DDAR [EP]GND
CB2012PK501T
C418
OPT 0.01uF
C437 C436 C414 C435 BOOT SS R429 R448
1 8 2.2K
0.1uF 10uF 10uF 0.1uF 10K
THERMAL
16V 10V 10V 16V

+1.10V_VDDC VIN EN
9
2 7 C
+1.5V_DDR Vout=1.25*(1+R2/R1)+Iadj*R2 L407 C417

0.1uF
POWER_ON/OFF_1
R444
10K B Q404
3.6uH PH COMP MMBT3904(NXP)
16V 3 6 C416
+3.3V_Normal +1.5V_DDR 3A 0.33uF E
OPT R433 16V
ZD401 C424 C421 C420 GND VSENSE 2.7K
22uF 22uF 4 5
L409 IC404 L411 2.5V 0.1uF 1%
AZ1117EH-ADJTRG1 16V 10V 10V C419 C434
BLM18PG121SN1D CB2012PK501T C423 R439 0.039uF 390pF
50V 20K
R1 50V 50V
270pF 1%
IN OUT
ADJ/GND
C426 R449 R453 ZD403
10uF 1K R1 0 2.5V R440 R2
10V 1/16W 47K
1% C431 1%
10uF
1.3A R450
200
1/16W R2
10V
1%
Vout=0.808*(1+R1/R2)
+5V_Normal & +5V_USB with OCP

+12V
C405 C406
10uF 10uF
16V
[EP]GND
PGND_2
PGND_1
PGOOD
VIN_2
VIN_1
OPT R410
V7V
100K
C403
100pF +5V_Normal
50V C409 L405
24
23
22
21
20
19
0.047uF 4.7uH
EN BST 25V
C404
R408 4700pF 1 18
4.7K 50V THERMAL
+3.3V_Normal COMP 25
LX_2 R421 C411 C412
2 17 18K 82pF 22uF
+3.3V_Normal OPT SS LX_1 1% 50V 16V
R459 3 16
OPT OPT 0 IC400 R1
ROSC FB
R403 R405 4 15
4.7K 4.7K TPS65282REGR
EN_SW2 SW_IN_2 R2
MHL_5V_EN 5 14
MHL_SW_TR
R463
MHL_SW_TR
R464
USB1_CTL
EN_SW1
6
4A 13
SW_IN_1
R422
3.3K
2.7K 10K 1%
10
11
12
7
MHL_SW_TR +3.3V_Normal C410

+5V_USB 10uF
Q408 10V
FAULT2
FAULT1
SW_OUT2
RLIM
AGND
SW_OUT1
E C
MHL_5V_EN R407 R409
MHL_SW_TR 10K 10K
C
R461 R415 5V_HDMI_4 AVDD5V_MHL
10K B R466
B 15K
/VBUS_EN 20K
5%
D401 R418
(Active Low) MHL_SW_TR MBR230LSFT1G
E MHL_SW_TR
Q407 R465 30V 10
10K
MHL_SW_TR C OPT C408
R462 R416 10uF
10K
/MHL_OCP_DET
USB1_OCD
B 100K 10V
MHL_OCP_EN
MHL_SW_TR
(Active High) Q409 E
Vout=0.8*(1+R1/R2)
THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES

SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS L14_M1A 2013.09.14
ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. Power_PD2 4
Downloaded
Copyright © 2014 LG from www.Manualslib.com
Electronics. Inc. All rights reserved.
manuals search engine LGE Internal Use Only
USB (SIDE)
+5V_USB
JK700
ZD700 C700 C703
SD05 22uF 22uF
3AU04S-305-ZC-(LG)
5V 10V 10V
USB DOWN STREAM
OPT OPT
2
SIDE_USB1_DM
3
SIDE_USB1_DP
OPT OPT OPT
C701 C702 D700
5pF 5pF RCLAMP0502BA
4
50V 50V
5

FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS L14_M1A 13/04/30
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. USB_S1 7
Downloaded
HDMI (REAR 1 / SIDE 1 MHL)
HDMI_1 HDMI_2 MHL
VA805
5V_HDMI_2 5V_DET_HDMI_2 5V_HDMI_4 5V_DET_HDMI_4
ESD_HDMI2
R808
HDMI-2
10K R814
HPD4
33
SHIELD ESD_HDMI2
R803 GND VA808
C HDMI-2
20 R809 R815 100
1K 10K 20
Q800 B DDC_SDA_4
MMBT3904(NXP) HPD2
19 HP_DET R816 100
19 DDC_SCL_4
R802 E R810 100 HDMI-2
VA802 DDC_SDA_2 5V R812
18 1.8K 18
ESD_HDMI1 VA809 VA810
R805
3.3K
R811 100 1.8K

VA800 DDC_SCL_2 GND HDMI-2
R813
ESD_HDMI2 ESD_HDMI2
17 17 3.3K
HDMI-2
VA803 VA804 16 DDC_DATA
16 ESD_HDMI1_VARISTOR
ESD_HDMI1 ESD_HDMI1
15 DDC_CLK HDMI_CEC
15 VA811
HDMI_ARC NC ESD_HDMI2
14 14
HDMI_CEC
13 CE_REMOTE
13
EAG59023302
EAG62611204
D803 12 CK-
12
1 10 D805
CK-_HDMI2
11 CK_GND 1 10
11 CK-_HDMI4
CK+ 2 9
10 CK+_HDMI2
10
CK+ 2 9
CK+_HDMI4
D0- 3 8
9
9
D0- 3 8
D0_GND 4 7
8 D0-_HDMI2
8
D0_GND 4 7
D0-_HDMI4
D0+ 5 6
7 D0+_HDMI2
7
D0+ 5 6
D1- D0+_HDMI4
6 ESD_HDMI1_IP4294 BODY_SHIELD
D1-
6 ESD_HDMI2_IP4294
D1_GND IP4294CZ10-TBR
5 20
D1_GND IP4294CZ10-TBR
19
HOT_PLUG_DETECT 5
D1+ D804 18
VDD[+5V]
4 17
D1+ D806
1 10 D1-_HDMI2
16
DDC/CEC_GND
SDA
4
3
D2-
15
14
SCL
RESERVED
D2-
1 10
2 9 D1+_HDMI2
13
12
CEC
3 D1-_HDMI4
2
D2_GND 11
TMDS_CLK-
TMDS_CLK_SHIELD
D2_GND
2 9
3 8 10
9
TMDS_CLK+
TMDS_DATA0- 2 D1+_HDMI4
1
D2+ 8
7
TMDS_DATA0_SHIELD
D2+
3 8
4 7 D2-_HDMI2
6
TMDS_DATA0+
TMDS_DATA1-
1
5
4
TMDS_DATA1_SHIELD
TMDS_DATA1+
4 7
VA801 5 6 D2+_HDMI2
3
2
TMDS_DATA2- D2-_HDMI4
ESD_HDMI1_VARISTOR 1
TMDS_DATA2_SHIELD
TMDS_DATA2+ 5 6
JK800 D2+_HDMI4
ESD_HDMI1_IP4294 JK801-*1 JK801 ESD_HDMI2
VA800-*1 DAADR019A HDMI-2 VA806
IP4294CZ10-TBR ESD_HDMI2_IP4294
1uF HDMI-2_EMI_FOOSUNG
10V IP4294CZ10-TBR
ESD_HDMI1_CAP MHL_CD_SENSE
VA801-*1
1uF C800
10V VA807 0.047uF R817
5.6V 25V 300K
ESD_HDMI1_CAP
OPT
MHL Spec
HDMI-2 HDMI-2
D803-*1 D804-*1 D805-*1 D806-*1
TMDS_CH1- NC_4 TMDS_CH1- NC_4 TMDS_CH1- NC_4 TMDS_CH1- NC_4
CEC TMDS_CH1+
GND_1
1
2
10
9
NC_3
GND_2
TMDS_CH1+
GND_1
1
2
10
9
NC_3
GND_2
TMDS_CH1+
GND_1
1
2
10
9
NC_3
GND_2
TMDS_CH1+
GND_1
1
2
10
9
NC_3
GND_2
3 8 3 8 3 8 3 8

4 7 4 7 4 7 4 7
TMDS_CH2+ NC_1 TMDS_CH2+ NC_1 TMDS_CH2+ NC_1 TMDS_CH2+ NC_1

R804 5 6 5 6 5 6 5 6
100
HDMI_CEC CEC_REMOTE_S7 ESD_HDMI1_IP4283 ESD_HDMI1_IP4283 ESD_HDMI2_IP4283 ESD_HDMI2_IP4283
IP4283CZ10-TBA IP4283CZ10-TBA IP4283CZ10-TBA IP4283CZ10-TBA
D803-*2 D804-*2 D805-*2 D806-*2

1 10 1 10 1 10 1 10
5V_HDMI_4 +5V_Normal 2 9 2 9 2 9 2 9
5V_HDMI_2 +5V_Normal +3.5V_ST
3 8 3 8 3 8 3 8
4 7 4 7 4 7 4 7
A1
A2
A1
A2
A1
A2
5 6 5 6 5 6 5 6
MMBD6100 MMBD6100
MMBD6100 D801 D802
D800 ESD_HDMI1_SEMTECH ESD_HDMI1_SEMTECH ESD_HDMI2_SEMTECH ESD_HDMI2_SEMTECH
C
RCLAMP0524PA RCLAMP0524PA RCLAMP0524PA RCLAMP0524PA

C
R800 R801 R806 R807

2.7K 2.7K
2.7K 2.7K
DDC_SDA_4
DDC_SDA_2
DDC_SCL_4
DDC_SCL_2

HDMI_R1_S1 8
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
Downloaded
SPDIF
SPDIF OPTIC JACK

+3.3V_Normal
5.15 Mstar Circuit Application
JK1001
JST1223-001
GND
1
Fiber Optic
VCC
2
VINPUT
3
SPDIF_OUT
4
SPDIF_CAP_68pF SPDIF_CAP_47pF
C1001 C1002 C1002-*1
FIX_POLE
OPT 1uF 68pF 47pF

10V 50V 50V
ESD Ready

FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS NC5_L14 2013/05/15
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. SPDIF 10
Downloaded
+1.5V_DDR +1.5V_DDR Option : Ripple Check !!!
R12011K1%
R1205 1K 1% R1204 1K 1%
+1.5V_DDR +1.5V_DDR
DDR_EXT
DDR_EXT
C1202 1000pF
A-MVREFDQ A-MVREFCA
1K1%
C1201 0.1uF
C1213 0.1uF
C12141000pF
10uF 10V
C1219
C1220
C1221
C1222
C1223
DDR_EXT
DDR_EXT
DDR_EXT
DDR_EXT
0.1uF
0.1uF
0.1uF
C1217
C1218
C1224
DDR_EXT
DDR_EXT
C1216
1uF
1uF
1uF
1uF
1uF
R1202
OPT OPT OPT OPT OPT OPT OPT OPT

OPT
CLose to DDR3 CLose to Saturn7M IC
DDR_1600_1G_HYNIX
IC1201 M1A_256M M1A_128M
H5TQ1G63EFR-PBC IC101 IC101-*1
DDR_1600_1G_SS DDR_1600_2G_HYNIX_OLD DDR_1600_2G_HYNIX_NEW LGE2132(M1A_256M) LGE2131(M1A_128M)
EAN61829003
IC1201-*1 IC1201-*2 IC1201-*3
M8 N3
K4B1G1646G-BCK0 H5TQ2G63DFR-PBC H5TQ2G63FFR-PBC A-MVREFCA VREFCA A0 A-MA0
EAN61836301 EAN61829203 EAN61829204 P7
A1 A-MA1 E11 E11
N3
A0 VREFCA
M8 N3
A0 VREFCA
M8 N3
A0 VREFCA
M8 P3 A-MA0 B_DDR3_A[0] B_DDR3_A[0]
P7
A1
P7
A1
P7
A1 A2 A-MA2 F12 F12
P3
A2
P3
A2
P3
A2 H1 N2 A-MA1 B_DDR3_A[1] B_DDR3_A[1]
N2
A3 VREFDQ
H1 N2
A3 VREFDQ
H1 N2
A3 VREFDQ
H1 A-MVREFDQ VREFDQ A3 A-MA3 D10 D10
P8
A4
P8
A4
P8
A4 P8 A-MA2 B_DDR3_A[2] B_DDR3_A[2]
P2
A5
P2
A5
P2
A5 A4 A-MA4 B10 B10
R8
A6 ZQ
L8 R8
A6 ZQ
L8 R8
A6 ZQ
L8
DDR_EXT P2 A-MA3 B_DDR3_A[3] B_DDR3_A[3]
R2
A7
R2
A7
R2
A7 R1203 A5 A-MA5 E15 E15
T8
A8
T8
A8
T8
A8 L8 R8 A-MA4 B_DDR3_A[4] B_DDR3_A[4]
R3
A9 VDD_1
B2 R3
A9 VDD_1
B2 R3
A9 VDD_1
B2
ZQ A6 A-MA6 B11 B11
L7
A10/AP VDD_2
D9 L7
A10/AP VDD_2
D9 L7
A10/AP VDD_2
D9
240 R2 A-MA5 B_DDR3_A[5] B_DDR3_A[5]
R7
A11 VDD_3
G7 R7
A11 VDD_3
G7 R7
A11 VDD_3
G7 +1.5V_DDR A7 A-MA7 F14 F14
N7
A12/BC VDD_4
K2 N7
A12/BC VDD_4
K2 N7
A12/BC VDD_4
K2 1% T8 A-MA6 B_DDR3_A[6] B_DDR3_A[6]
T3
A13 VDD_5
K8 T3
A13 VDD_5
K8 T3
A13 VDD_5
K8
A8 A-MA8 C11 C11
VDD_6
N1
VDD_6
N1
VDD_6
N1 B2 R3 A-MA7 B_DDR3_A[7] B_DDR3_A[7]
M7
NC_5 VDD_7
N9 M7
NC_5 VDD_7
N9 M7
NC_5 VDD_7
N9
VDD_1 A9 A-MA9 D14 D14
DDR_EXT 10V C1203 D9 L7 A-MA8
R1 R1 R1
VDD_8 VDD_8 VDD_8 10uF B_DDR3_A[8] B_DDR3_A[8]
M2
BA0 VDD_9
R9 M2
BA0 VDD_9
R9 M2
BA0 VDD_9
R9
VDD_2 A10/AP A-MA10 A12 A12
N8
BA1
N8
BA1
N8
BA1 DDR_EXT C1204 0.1uF G7 R7 A-MA9 B_DDR3_A[9] B_DDR3_A[9]
M3
BA2
M3
BA2
M3
BA2 VDD_3 A11 A-MA11 F16 F16
VDDQ_1
A1
VDDQ_1
A1
VDDQ_1
A1
DDR_EXT C1205 0.1uF K2 N7 A-MA10 B_DDR3_A[10] B_DDR3_A[10]
J7
CK VDDQ_2
A8 J7
CK VDDQ_2
A8 J7
CK VDDQ_2
A8
VDD_4 A12/BC A-MA12 D13 D13
K7
CK VDDQ_3
C1 K7
CK VDDQ_3
C1 K7
CK VDDQ_3
C1
DDR_EXT C1206 0.1uF K8 T3 A-MA11 B_DDR3_A[11] B_DDR3_A[11]
K9
CKE VDDQ_4
C9 K9
CKE VDDQ_4
C9 K9
CKE VDDQ_4
C9
VDD_5 NC_7 A-MA13 D15 D15
VDDQ_5
D2
VDDQ_5
D2
VDDQ_5
D2
DDR_EXT C1207 0.1uF N1 A-MA12 B_DDR3_A[12] B_DDR3_A[12]
L2
CS VDDQ_6
E9 L2
CS VDDQ_6
E9 L2
CS VDDQ_6
E9
VDD_6 C12 C12
K1
ODT VDDQ_7
F1 K1
ODT VDDQ_7
F1 K1
ODT VDDQ_7
F1
DDR_EXT C1208 0.1uF N9 M7 A-MA13 B_DDR3_A[13] B_DDR3_A[13]
J3
RAS VDDQ_8
H2 J3
RAS VDDQ_8
H2 J3
RAS VDDQ_8
H2
VDD_7 NC_5 E13 E13
K3
CAS VDDQ_9
H9 K3
CAS VDDQ_9
H9 K3
CAS VDDQ_9
H9
DDR_EXT C1209 0.1uF R1 A-MA14 B_DDR3_A[14] B_DDR3_A[14]
L3 L3 L3
WE WE WE VDD_8
NC_1
J1
NC_1
J1
NC_1
J1
DDR_EXT C1210 0.1uF R9 M2
T2 J9 T2 J9 T2 J9
VDD_9 BA0 A-MBA0 A-MCK A9 A9
1%
DDR_EXT DDR_EXT
RESET NC_2 RESET NC_2 RESET NC_2

R1207
NC_3
L1
NC_3
L1
NC_3
L1
DDR_EXT C1211 0.1uF N8 A-MBA0 B_DDR3_BA[0] B_DDR3_BA[0]
NC_4
L9
NC_4
L9
NC_4
L9
BA1 A-MBA1 D16 D16
F3 T7 F3 T7 F3 T7
C1212 0.1uF M3 A-MBA1 B_DDR3_BA[1] B_DDR3_BA[1]
56
G3
DQSL NC_6
G3
DQSL NC_6
G3
DQSL NC_6
DDR_EXT BA2 A-MBA2 DDR_EXT A10 A10
DQSL DQSL DQSL
A1 C1215 A-MBA2 B_DDR3_BA[2] B_DDR3_BA[2]
C7 A9 C7 A9 C7 A9
DQSU VSS_1 DQSU VSS_1 DQSU VSS_1 VDDQ_1
A8 J7
1%
B7 B3 B7 B3 B7 B3
R1208
DQSU VSS_2 DQSU VSS_2 DQSU VSS_2

VSS_3
E1
VSS_3
E1
VSS_3
E1
VDDQ_2 CK 0.01uF C13 C13
E7
DML VSS_4
G8 E7
DML VSS_4
G8 E7
DML VSS_4
G8 C1 K7 50V A-MCK B_DDR3_MCLK B_DDR3_MCLK
B13 B13
56
D3 J2 D3 J2 D3 J2
DMU VSS_5 DMU VSS_5 DMU VSS_5 VDDQ_3 CK
VSS_6
J8
VSS_6
J8
VSS_6
J8 C9 K9 A-MCKB B_DDR3_MCLKZ B_DDR3_MCLKZ
E3
DQL0 VSS_7
M1 E3
DQL0 VSS_7
M1 E3
DQL0 VSS_7
M1
VDDQ_4 CKE A-MCKE E17 E17
F7
DQL1 VSS_8
M9 F7
DQL1 VSS_8
M9 F7
DQL1 VSS_8
M9 D2 A-MCKE B_DDR3_MCLKE B_DDR3_MCLKE
F2
DQL2 VSS_9
P1 F2
DQL2 VSS_9
P1 F2
DQL2 VSS_9
P1
VDDQ_5 A-MCKB
F8
DQL3 VSS_10
P9 F8
DQL3 VSS_10
P9 F8
DQL3 VSS_10
P9 E9 L2
H3
DQL4 VSS_11
T1 H3
DQL4 VSS_11
T1 H3
DQL4 VSS_11
T1
VDDQ_6 CS A/B_DDR3_CS B8 B8
H8
DQL5 VSS_12
T9 H8
DQL5 VSS_12
T9 H8
DQL5 VSS_12
T9 F1 K1 A-MODT B_DDR3_ODT B_DDR3_ODT
G2
DQL6
G2
DQL6
G2
DQL6 VDDQ_7 ODT A-MODT C8 C8
H7
DQL7
H7
DQL7
H7
DQL7 H2 J3 A-MRASB B_DDR3_RASZ B_DDR3_RASZ
VSSQ_1
B1
VSSQ_1
B1
VSSQ_1
B1
VDDQ_8 RAS A-MRASB +1.5V_DDR B9 B9
D7
DQU0 VSSQ_2
B9 D7
DQU0 VSSQ_2
B9 D7
DQU0 VSSQ_2
B9 H9 K3 A-MCASB B_DDR3_CASZ B_DDR3_CASZ
C3
DQU1 VSSQ_3
D1 C3
DQU1 VSSQ_3
D1 C3
DQU1 VSSQ_3
D1
VDDQ_9 CAS A-MCASB DDR_EXT D11 D11
L3 A-MWEB
A-MDQSU
A-MDQSL
C8 D8 C8 D8 C8 D8
B_DDR3_WEZ B_DDR3_WEZ
A-MWEB R1206
DQU2 VSSQ_4 DQU2 VSSQ_4 DQU2 VSSQ_4
E2 E2 E2
C2
DQU3 VSSQ_5
C2
DQU3 VSSQ_5
C2
DQU3 VSSQ_5 WE
A7
DQU4 VSSQ_6
E8 A7
DQU4 VSSQ_6
E8 A7
DQU4 VSSQ_6
E8 J1
A2
DQU5 VSSQ_7
F9 A2
DQU5 VSSQ_7
F9 A2
DQU5 VSSQ_7
F9
NC_1 10K F10 F10
B8 G1 B8 G1 B8 G1 J9 T2 A-MRESETB B_RESET B_RESET
A-MDQSUB
A-MDQSLB
DQU6 VSSQ_8 DQU6 VSSQ_8 DQU6 VSSQ_8

A3
DQU7 VSSQ_9
G9 A3
DQU7 VSSQ_9
G9 A3
DQU7 VSSQ_9
G9
NC_2 RESET A-MRESETB
L1
NC_3 D12 D12
L9 A/B_DDR3_CS B_DDR3_CS0 B_DDR3_CS0
NC_4
T7 F3
A-MA14 NC_6 DQSL A-MDQSL A19 A19
G3 B_DDR3_DQSL B_DDR3_DQSL
DQSL A-MDQSLB B18 B18
B_DDR3_DQSU B_DDR3_DQSU
A9 C7
VSS_1 DQSU A-MDQSU C16 C16
B3 B7 A-MDML B_DDR3_DQML B_DDR3_DQML
VSS_2 DQSU A-MDQSUB D21 D21
E1 A-MDMU B_DDR3_DQMU B_DDR3_DQMU
VSS_3
G8 E7
VSS_4 DML A-MDML C18 C18
J2 D3 B_DDR3_DQSBL B_DDR3_DQSBL
VSS_5 DMU A-MDMU C17 C17
J8 B_DDR3_DQSBU B_DDR3_DQSBU
VSS_6
M1 E3
VSS_7 DQL0 A-MDQL0 A20 A20
M9 F7 A-MDQL0 B_DDR3_DQL[0] B_DDR3_DQL[0]
VSS_8 DQL1 A-MDQL1 A16 A16
P1 F2 A-MDQL1 B_DDR3_DQL[1] B_DDR3_DQL[1]
VSS_9 DQL2 A-MDQL2 C19 C19
P9 F8 A-MDQL2 B_DDR3_DQL[2] B_DDR3_DQL[2]
T1 H3 A-MDQL3 B_DDR3_DQL[3] B_DDR3_DQL[3]
T9 H8 A-MDQL4 B_DDR3_DQL[4] B_DDR3_DQL[4]
G2 A-MDQL5 B_DDR3_DQL[5] B_DDR3_DQL[5]
DQL6 A-MDQL6 B21 B21
H7 A-MDQL6 B_DDR3_DQL[6] B_DDR3_DQL[6]
DQL7 A-MDQL7 B15 B15
B1 A-MDQL7 B_DDR3_DQL[7] B_DDR3_DQL[7]
VSSQ_1 F18 F18
B9 D7 A-MDQU0 B_DDR3_DQU[0] B_DDR3_DQU[0]
VSSQ_2 DQU0 A-MDQU0 D19 D19
D1 C3 A-MDQU1 B_DDR3_DQU[1] B_DDR3_DQU[1]
D8 C8 A-MDQU2 B_DDR3_DQU[2] B_DDR3_DQU[2]
VSSQ_4 DQU2 A-MDQU2 E21 E21
E2 C2 A-MDQU3 B_DDR3_DQU[3] B_DDR3_DQU[3]
VSSQ_5 DQU3 A-MDQU3 E19 E19
E8 A7 A-MDQU4 B_DDR3_DQU[4] B_DDR3_DQU[4]
F9 A2 A-MDQU5 B_DDR3_DQU[5] B_DDR3_DQU[5]
G1 B8 A-MDQU6 B_DDR3_DQU[6] B_DDR3_DQU[6]
VSSQ_8 DQU6 A-MDQU6 F20 F20
G9 A3 A-MDQU7 B_DDR3_DQU[7] B_DDR3_DQU[7]
VSSQ_9 DQU7 A-MDQU7
R1209
E9 E9
ZQ ZQ
240
1%

FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS NC5_S7LR(M1A) 2013/05/20
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. 1_DDR 12
Downloaded
Serial Flash for SPI boot
+3.5V_ST +3.5V_ST
SPI_FLASH_MACRONIX
OPT IC1300
R1301
+3.5V_ST 4.7K MX25L8006EM2I-12G
C1300
CS# VCC 0.1uF
/SPI_CS 1 8
OPT
R1300
10K SO/SIO1 HOLD#
SPI_SDO 2 7
WP# SCLK
/FLASH_WP 3 6 SPI_SCK
R1302
GND SI/SIO0 33
4 5 SPI_SDI
SPI_FLASH_WINBOND
IC1300-*1
W25Q80BVSSIG
CS VCC
1 8
DO[IO1] HOLD[IO3]
2 7
%WP[IO2] CLK
3 6
GND DI[IO0]
4 5

THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. S_FLASH 13
Downloaded
LVDS_EU
FOR FHD REVERSE(10bit)

[51Pin LVDS Connector] [30Pin LVDS Connector]
(For FHD 60Hz) Change in S7LR
(For HD 60Hz_Normal)
MO_FHD MIRROR Pol-change
P1800
FI-RE51S-HF-J-R1500 RXA4+ RXA0+ RXA0- MO_HD
RXA4- RXA0- RXA0+ P1801
10031HR-30
RXA3+ RXA1+ RXA1-
1
RXA3- RXA1- RXA1+
2
LVDS_SEL 1
RXACK+ RXA2+ RXA2-
3
2
+3.3V_Normal RXACK- RXA2- RXA2+
4 VCOM_SDA 3 VCOM_SDA
RXA2+ RXACK+ RXACK-
5 VCOM_SCL
OPT 4 VCOM_SCL
RXA2- RXACK- RXACK+
6 R1806
3.3K 5
RXA1+ RXA3+ RXA3-
7
6 RXA3+
OPT RXA1- RXA3- RXA3+
8
R1807 7
RXA0+ RXA4+ RXA4- RXA3-
9 10K
8
RXA0- RXA4- RXA4+
10
9 RXACK+
11
10 RXACK-
12 RXA4+ RXB4+ RXB0+ RXB0-
11
13 RXA4- RXB4- RXB0- RXB0+
12 RXA2+
13 RXA2-
14
16 RXACK+ RXBCK+ RXB2+ RXB2-
15 RXA1+
17 RXACK- RXBCK- RXB2- RXB2+
16 RXA1-
18 RXB2+ RXBCK+ RXBCK-
17
19 RXA2+ RXB2- RXBCK- RXBCK+ LVDS_SEL
18 RXA0+
20 RXA2- RXB1+ RXB3+ RXB3- +3.3V_Normal
19 RXA0-
21 RXB1- RXB3- RXB3+
20
22 RXB0+ RXB4+ RXB4- OPT
RXA1+ 21 R1808
3.3K
22
24 RXA0+ 23 OPT
R1809
25 RXA0- 10K
24
26 R1801 0
25 PANEL_VCC
MO_FHD
27
28
FOR FHD REVERSE(8bit) 26
RXB4+ 27
29 RXB4- Change in S7LR 28
30 RXB3+ 29
31 MIRROR Pol-change Shift
RXB3- 30
32 RXBCK+
RXA4- RXA4- RXA4+ RXA0+ 31
33 RXBCK-
34
RXA3- RXA0- RXA0+ RXA1+
35 RXB2+
RXACK+ RXA1+ RXA1- RXA2-
36 RXB2-
RXACK- RXA1- RXA1+ RXA2+
37
RXA2+ RXA2+ RXA2- RXACK-
38 RXB1+
RXA2- RXA2- RXA2+ RXACK+
39 RXB1-
RXA1+ RXACK+ RXACK- RXA3-
40 RXB0+
RXA1- RXACK- RXACK+ RXA3+
41 RXB0-
EU pin assign is different from NON EU.
42 R1802 0
MO_FHD
R1803 0 RXA0- RXA3- RXA3+ RXA4+
Because of position of HD wafer.
43
MO_FHD
44
45 RXB4+ RXB4+ RXB4- RXB0-

V-COM I2C
46 RXB4- RXB4- RXB4+ RXB0+
PANEL_VCC +3.3V_Normal
47 RXB3+ RXB0+ RXB0- RXB1- URSA/VCOM_SCL
48 RXB3- RXB0- RXB0+ RXB1+ URSA/VCOM_SDA
49 C1800 RXBCK+ RXB1+ RXB1- RXB2-

VCOM_I2C_PULL_UP VCOM_I2C_PULL_UP
0.1uF
50 16V RXBCK- RXB1- RXB1+ RXB2+ R1810 R1811
2K 2K
51 RXB2+ RXB2+ RXB2- RXBCK-
VCOM_I2C
RXB2- RXB2- RXB2+ RXBCK+ R1804
52 0
RXB1+ RXBCK+ RXBCK- RXB3- VCOM_SCL URSA/VCOM_SCL
R1805
0
RXB1- RXBCK- RXBCK+ RXB3+ VCOM_SDA URSA/VCOM_SDA
VCOM_I2C
RXB0+ RXB3+ RXB3- RXB4-
RXB0- RXB3- RXB3+ RXB4+

THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. LVDS_EU 18
Downloaded
CI Region * Option name of this page : CI_SLOT
(because of Hong Kong)
CI SLOT
+5V_CI_ON
CI_DATA[0-7]
CI TS INPUT
CI_DATA[0-7]
+5V_Normal AR1903 33
C1903 FE_TS_DATA[7]
CI_MDI[7]
10uF FE_TS_DATA[6]
10V CI_MDI[6]
FE_TS_DATA[0-7]
R1908 FE_TS_DATA[5]
CI_MDI[5]
10K FE_TS_DATA[4]
CI_SLOT_JACK CI_MDI[4]
/CI_CD1 P1900
10067972-000LF
AR1904 33 FE_TS_DATA[3]
R1914 35 1 CI_MDI[3]
100 CI_DATA[3] FE_TS_DATA[2]
36 2 CI_MDI[2] FE_TS_DATA[1]
AR1900 CI_DATA[4]
CI_DATA[0-7]
33 37 3 CI_MDI[1] FE_TS_DATA[0]
CI_DATA[5] R1919
CI_TS_DATA[4] 38 4 10K CI_MDI[0]
CI_DATA[6]
CI_TS_DATA[5] 39 5
CI_DATA[7] FE_TS_DATA[0-7]
CI_TS_DATA[6] 40 6
R1917 R1921 33
CI_TS_DATA[7] 41 7 47 CI_MISTRT FE_TS_SYNC
CI_ADDR[10] /PCM_CE R1922 33
42 8 CI_MIVAL_ERR FE_TS_VAL_ERR
R1910 10K R1923 100
43 9 CI_OE CI_MCLKI FE_TS_CLK
CI_ADDR[11]
CI_IORD 44 10 +5V_Normal
CI_ADDR[9]
CI_IOWR 45 11
CI_ADDR[8]
46 12 R1920
CI_ADDR[13] 10K
CI_MDI[0] 47 13
CI_ADDR[14]
CI_MDI[1] 48 14
CI_MDI[2] 49 15 CI_WE
50 16 R1918 100
CI_MDI[3] /PCM_IRQA
51 17
GND
C1901
0.1uF
52
53
18
19
C1904
0.1uF
C1905
0.1uF
CI HOST I/F
CI_MDI[4]
GND
CI_MDI[5] 54 20
+5V_Normal CI_ADDR[12]
CI_MDI[6] 55 21 CLOSE TO MSTAR
CI_ADDR[7]
R1900 CI_MDI[7] 56 22 GND +3.3V_Normal
10K R1911 10K CI_ADDR[6]
57 23
R1903 CI_ADDR[5]
47 58 24
PCM_RST CI_ADDR[4]
R1904 47 CI_DET
/PCM_WAIT 59 25 IC1902
CLOSE TO MSTAR CI_ADDR[3]
REG 60 26 C1906
R1905 100 CI_ADDR[2]
CI_TS_CLK 61 27 0.1uF
R1906 33 CI_ADDR[1] 1OE BUFFER_ORG VCC 16V
CI_TS_VAL 62 28 1 20
R1907 33 CI_ADDR[0]
CI_TS_SYNC 63 29
CI_DATA[0]
64 30 1A1 2OE
AR1901 33 CI_DATA[1] 2 19
65 31 CI_ADDR[0-14] PCM_A[0]
CI_TS_DATA[0] CI_DATA[2] AR1902 AR1910
66 32 100
CI_TS_DATA[1] 2Y4 1Y1 100
67 33 3 18
CI_TS_DATA[2] CI_ADDR[7] CI_ADDR[0]
68 34
G2 69 G1 CI_ADDR[5] 1A2 2A4 CI_ADDR[2]
PCM_A[1] 4 17 PCM_A[7]
R1912 CI_ADDR[4] CI_ADDR[3]
100
/CI_CD2 2Y3 1Y2
TC74LCX244FT
+5V_Normal GND 5 16
GND 1A3 2A3

PCM_A[2] 6 15 PCM_A[6]
C1900
2pF
R1909
50V 2Y2 1Y3
10K GND 7 14
CLOSE TO MSTAR
1A4 2A2
PCM_A[3] 8 13 PCM_A[5]
2Y1 1Y4
CI_MISTRT 9 12
CI_MIVAL_ERR
GND 2A1
10 11 PCM_A[4]
CI_MCLKI
CI DETECT +3.3V_Normal
OR_GATE_CI_PHILIPS
IC1900
74LVC1G32GW +3.3V_Normal
B 1 5 VCC
/CI_CD2
A 2
/CI_CD1 AR1905 33
GND 3 4 Y R1913 CI_DATA[0] PCM_D[0]
10K CI_DATA[1] PCM_D[1]
CI_DATA[0-7]
CI_DATA[2] PCM_D[2]
OR_GATE_CI_TI OR_GATE_CI_TOSHIBA R1924 CI_DATA[3] PCM_D[3]
IC1900-*1 IC1900-*2 0
SN74LVC1G32DCKR TOSHIBA ELECTRONICS KOREA CORPORATION
CI_DET
IC1902-*1
PCM_D[0-7]
A VCC IN_B VCC

1 5 1 5
/PCM_CD AR1906 33
B IN_A R1915 CI_DATA[4] PCM_D[4] 74LCX244FT
2 2
47 CI_DATA[5] PCM_D[5]
GND Y GND OUT_Y
3 4 3 4
CI_DATA[6] PCM_D[6]
1OE BUFFER_CI VCC
CI_DATA[7] PCM_D[7] 1 20
1A1 2OE
2 19
PCM_D[0-7]
CI_DATA[0-7] 2Y4 1Y1
CI POWER ENABLE CONTROL 3 18
1A2 2A4
4 17
AR1908 33
CI_ADDR[8] PCM_A[8] 2Y3 1Y2
CI_ADDR[9] PCM_A[9] 5 16
+5V_Normal IC1901
AP2151WG-7 +5V_CI_ON CI_ADDR[10] PCM_A[10]
L1900 CI_ADDR[11] PCM_A[11] 1A3 2A3
6 15
BLM18PG121SN1D
IN OUT
5 1
2Y2 1Y3
7 14
GND AR1909 33
2 CI_ADDR[12] PCM_A[12]
R1916 1A4 2A2
C1902 8 13
100K CI_ADDR[13] PCM_A[13]
R1902 1uF
100 EN FLG 10V CI_ADDR[14] PCM_A[14]
PCM_5V_CTL 4 3
/PCM_REG 2Y1 1Y4
REG 9 12
R1901
10K
GND 2A1
10 11
AR1907 33
CI_OE /PCM_OE
CI_WE /PCM_WE
CI_IORD /PCM_IORD
CI_IOWR /PCM_IOWR

FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS NC5_M1A 2013.04.29
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. PCMCI 19
Downloaded
ETHERNET
* H/W option : ETHERNET
JK2100
RJ45VT-01SN002
1
1
EPHY_TP
ETHERNET
2
2
3
3
EPHY_TN
4
4
EPHY_RP
5
5
6
6
EPHY_RN
7
7
8
8
ETHERNET ETHERNET
C2105 C2104
0.01uF 0.01uF
50V 50V

LAN 21
Downloaded
DVB-S2 LNB Part Allegro
(Option:LNB)
Input trace widths should be sized to conduct at least 3A
Ouput trace widths should be sized to conduct at least 2A
3A
+12V_LNB
2A LNB_SX34
D2705-*1
40V
LNB
Max 1.3A
L2702
SP-7850_15
D2705 15uH
LNB LNB_SMAB34
D2703 40V 3.5A
30V
LNB
C2708
LNB LNB LNB 10uF
LNB
C2703 C2704 C2705 C2706 25V
0.01uF 10uF 10uF 10uF
50V 25V 25V 25V
close to Boost pin(#1)

A_GND A_GND
A_GND
close to VIN pin(#15)

[EP]GND
LNB
LNB C2709
BOOST
GNDLX
NC_3
NC_2
C2707 0.1uF
50V
LX
0.1uF
20
19
18
17
16
LNB
D2702 VCP 1 15 VIN
close to TUNER MBR230LSFT1G
LNB
THERMAL
GND
LNB_OUT 2 21 14
LNB
30V NC_1 VREG R2703
3 13 36K
LNB
LNB LNB LNB TDI ISET 1/16W 1%
R2702 C2712 LNB_SMAB34 4 IC2701 12
LNB LNB LNB LNB C2713
C2714 C2701 C2702 D2701
2.2K 0.22uF 0.1uF D2704 TDO A8303SESTR-T TCAP
1W 25V 50V 40V 5 11
18pF 18pF 33pF
10
LNB
6
LNB_SX34 C2710
D2704-*1 0.1uF
IRQ
SCL
SDA
ADD
TONECTRL
40V LNB
C2711
Close to Tuner 0.22uF
Surge protectioin
A_GND A_GND
R2706
0
LNB LNB
R2704 R2705
33 33
Caution!! need isolated GND
R2701
0
DEMOD_SCL
DEMOD_SDA
LNB_TX
A_GND
Max 1.3A
+12V +12V_LNB
LNB
L2701
BLM18PG121SN1D

LNB 27
Downloaded
SCART_COMPONENT
COMPONENT SCART AMP
+12V
JK2802
PPJ245N2-01
R2811 EU
6E [RD2]E-LUG 10K C2808
COMP2_R_IN
VA2804 R2803 R2816 IC2801 0.1uF
[RD2]O-SPRING 5.6V 470K 12K 50V
5E AZ4580MTR-E1
OPT
R2810 EU
4E [RD2]CONTACT 10K R2831
COMP2_L_IN 2.2K OUT1 8 VCC
R2815 DTV/MNT_L_OUT 1
[WH]O-SPRING
VA2803 R2802
470K 12K EU EU EU
5D 5.6V +3.3V_Normal EU
C2804 R2834 R2844
OPT OPT 33K IN1- 7 OUT2 2.2K
R2817 R2818 10uF R2832 2
[RD1]CONTACT 10K 1K 16V DTV/MNT_R_OUT
4C 470K EU
COMP2_DET R2841 EU
EU IN1+ IN2- 33K C2812
[RD1]O-SPRING VA2816 EU 3 6 OPT 10uF
5C R2836
COMP2_Pr+ 5.6V C2807 10K EU R2843 16V
VA2802 R2801 33pF 470K
OPT R2839
7C [RD1]E-LUG-S 5.5V 75 VEE 5 IN2+ 10K
4 EU
ESD_COMP C2810
[BL]O-SPRING EU 33pF
5B
COMP2_Pb+ R2835
VA2801 R2800 5.6K EU
[GN/YL]CONTACT 5.5V +3.3V_Normal SCART1_Lout R2840
4A 75 5.6K
ESD_COMP SCART1_Rout
R2812 R2814 330pF 220K
[GN/YL]O-SPRING 1K C2806 R2833
5A 10K EU EU
AV_CVBS_DET EU EU
VA2800 OPT R2842 C2811
C2800 220K 330pF
6A [GN/YL]E-LUG 5.6V
OPT 0.1uF
16V
COMP2_Y+/AV_CVBS_IN
R2804 CLOSE TO MSTAR
D2800-*1 D2800 75
ESD_COMP_ZENER_ROHM
ESD_COMP_ZENER_KEC CLOSE TO MSTAR
D2801-*1 D2801
ESD_COMP_ZENER_KEC ESD_COMP_ZENER_ROHM
FULL SCART +3.3V_Normal [SCART AUDIO MUTE] +3.5V_ST
R2819 DTV/MNT_L_OUT SCART_MUTE

10K R2837 SCART_MUTE
2K R2845
R2820 1K SCART_MUTE 10K
SC1/COMP1_DET Q2802
VA2815 EU MMBT3904(NXP)
5.6V R2850 1K
AV2_CVBS_DET
OPT AV2
SCART1_MUTE
SCART_MUTE
DTV/MNT_R_OUT R2838 SCART_MUTE
2K C2809
SCART_MUTE 0.1uF
Q2803
SC1/AV2_CVBS_IN MMBT3904(NXP)
EU
R2813 OPT
C2801
75 47pF
AV_DET 50V
22 VA2807
COM_GND 5.5V
ESD_SCART
21
SYNC_IN EU
L2800 AV2
20 CM2012FR22KT
SYNC_OUT 220nH JK2803
EU EU DTV/MNT_VOUT
19 PPJ231-01
SYNC_GND2 VA2808 EU C2815 C2816
VA2814 R2821 R2851
18 20V 5.6V 75 68pF 68pF 4 10K
SYNC_GND1 ESD_SCART 50V 50V EU AV2_R_IN_A AV2_R_IN_A AV2_R_IN
R2827 R2846 AV2
17 22 0
RGB_IO 5 AV2 VA2818 R2854 C2817 R2853
SC1_FB AV2_L_IN_A 1000pF 12K
16 5.6V 470K AV2
R_OUT AV2_LR_ZENER AV2 50V
7 OPT
15 SC1_R+/COMP1_Pr+
RGB_GND ESD_SCART
VA2810 R2807 R2852
14 75 EU 8
R_GND 20V 10K
R2822 AV2_L_IN_A AV2_L_IN
13 75 R2849 AV2
D2B_OUT 6 R2848 0
0 AV2 R2855
12 EU VA2819 R2856 C2818 12K
G_OUT 5.6V 470K 1000pF AV2
AV2_LR_ZENER AV2 50V
11 SC1_G+/COMP1_Y+ OPT
D2B_IN VA2811 R2808
10 20V 75
G_GND ESD_SCART EU
9 R2824
ID 15K R2847
0
8 SC1_ID AV2
B_OUT EU AV2_CVBS_DET
7 SC1_B+/COMP1_Pb+ R2828
AUDIO_L_IN VA2812 VA2817 VA2820
20V 3.9K 5.6V
20V R2805 OPT
6 75 ESD_SCART
B_GND ESD_SCART
5
AUDIO_GND EU
4
AUDIO_L_OUT R2826
10K
3 SC1/COMP1_L_IN
AUDIO_R_IN R2823
0
2 EU R2806 R2829
AUDIO_R_OUT VA2813 470K 12K
5.6V
EU
1
ESD_SCART
SC1/AV2_CVBS_IN
AV2_L_IN_A ZD2800-*1 ZD2800 AV2
EU EU C2819
AV2_CVBS_ZENER_KEC AV2_CVBS_ZENER_ROHM R2857 47pF
JK2801 R2825 75
10K ZD2801-*1 ZD2801 50V
PSC008-01 SC1/COMP1_R_IN
1608 AV2
R2858 AV2_CVBS_ZENER_KEC AV2_CVBS_ZENER_ROHM 1%
0 VA2809
EU 5.6V
ESD_SCART R2809 R2830
470K 12K
Size Check !!!
EU
AV2_R_IN_A
AV2
DTV/MNT_L_OUT
EU
VA2806 C2813
5.6V 1000pF
OPT 50V
DTV/MNT_R_OUT
EU
VA2805 C2814
5.6V 1000pF
OPT 50V

THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. SCART_ COMPONENT 28
Downloaded
Headphone
*Option : HEAD_PHONE_EU
Close to the Main IC
HEAD_PHONE
L3000
5.6uH HEAD_PHONE
HP_LOUT
HEAD_PHONE C3000 OPT C
C3004 HEAD_PHONE E
10uF C3002 R3002
4.7uF 16V 1000pF Q3002 B Q3004
1K MMBT3904(NXP)
10V 50V MMBT3904(NXP) B OPT HEAD_PHONE
OPT JK3000
+3.5V_ST E +3.3V_Normal
C KJA-PH-0-0177
GND 5
E
OPT OPT HEAD_PHONE
Q3001 R3005
10K L 4
OPT MMBT3906(NXP)
C R3001 B
R3000 3.3K
1K B C DETECT 3
SIDE_HP_MUTE HP_DET
Q3000 R3004
MMBT3904(NXP) 1K
OPT E HEAD_PHONE R 1
HEAD_PHONE
L3001 HEAD_PHONE
5.6uH
HP_ROUT
HEAD_PHONE C3001 OPT HEAD_PHONE C E
C3005 10uF C3003 R3003
4.7uF 16V 1000pF Q3003 B Q3005
1K MMBT3904(NXP) MMBT3904(NXP)
10V 50V B
OPT OPT
E C

THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. HEAD_PHONE_EU 30
Downloaded
L14 TUNER_EU T/C_T2/C/S2_CHINA
TU_I2C Multi option
TU3700 TU3702 TU3703 TU3701
TU_I2C_FILTER
TDJH-G101D TDJM-G105D TDJM-C301D TDJM-G101D RF_SW_OPT
R2603
0
TU_ATSC
C3705-*1
18pF
TU_ATSC R3838-*1
R3716-*1 MLG1005SR27JT
1.8K
RF_SWITCH_CTL TU_ATSC
TUNER_T/C TUNER_AJ_T2 TUNER_CHINA TUNER_T2/C/S2 +3.3V_LNA TU_ATSC R3717-*1 TU_I2C_FILTER
1.8K R3739-*1
C2603 C3707-*1 MLG1005SR27JT
0.1uF 18pF
B1[+3.3V] B1[+3.3V] B1[+3.3V] B1[+3.3V] 16V
RF_SW_OPT
1 1 1 1
C3708 C3714
NC_1 NC_1 RF_SW_CTL NC_1 100pF 0.1uF Close to TUNER
50V 16V
2 2 2 2 +3.3V_TU
IF_AGC AIF_AGC NC_1 AIF_AGC should be guarded by ground
3 3 3 3 C3703 IF_AGC_MAIN TU_NON_ATSC TU_NON_ATSC
0.1uF R3714 R3716 R3717
16V 0
SCL SCL_RF SCL_RF SCL_RF TU_I2C_NON_FILTER
R3738 33
1K 1K
4 4 4 4 TU_SCL
SDA SDA_RF SDA_RF SDA_RF TU_I2C_NON_FILTER

5 5 5 5 C3705 C3707
R3739 33
TU_SDA
TU_NON_ATSC TU_ATSC C3710 C3711 R3726 OPT 0
20pF 20pF 20pF 20pF
IF[P] AIF[P] NC_2 AIF[P] R3709
10
R3709-*1 TU_NON_ATSC TU_NON_ATSC
TU_NON_ATSC TU_NON_ATSC +3.3V_TU
+3.3V_TU
6 6 6 6 0 IF_P_MSTAR CHINA CHINA
CHINA R3732 R3735
CHINA
IF[N] AIF[N] NC_3 AIF[N] R3725
470 R3728
220 220
7 7 7 7 IF_N_MSTAR
82
TU_SIF TU_CVBS
TU_NON_ATSC TU_ATSC E
R3710 R3710-*1 CHINA
NC_2 NC_2 SIF NC_2 10 C3726
E
CHINA Q3701
8 8 8 8 0 Q3700 B MMBT3906(NXP)
0.1uF R3724 B MMBT3906(NXP) C
4.7K
NC_3 NC_3 CVBS NC_3 16V
CHINA
CHINA C
9 9 9 9 R3731 OPT 0
close to TUNER
NC_4 NC_4 NC_4
10 10 10 CHINA
AR3700-*1 47
A1 B1 B2[+3.3V] NC_5 B2[+3.3V] +3.3V_TU

A1 B1 11 11 11 T2_OR_CHINA
C3718
T2_OR_CHINA
C3722
AR3700
100pF 0.1uF 0
47 ERROR ERROR ERROR 50V 16V 1/16W
12 12 12
TU_GND_A
TU_GND_B
FE_TS_ERR CHINA
AR3701-*1 47
FE_TS_CLK
GND_1 GND_1 GND_1 FE_TS_SYNC
SHIELD 13 13 13 FE_TS_VAL
T2
MCLK MCLK MCLK
14 14 14 CHINA
AR3702-*1 47
SYNC SYNC SYNC
15 15 15
VAILD VAILD VALID
16 16 16
AR3701
0 FE_TS_DATA[0-7]
D0 D0 D0 1/16W
TU3700-*1 17 17 17 FE_TS_DATA[0]
FE_TS_DATA[1]
D1 D1 D1 FE_TS_DATA[2]
TDJH-H101F 18 18 18 FE_TS_DATA[3]
T2
D2 D2 D2
TUNER_NTSC 19 19 19
B1[+3.3V] D3 D3 D3
1 20 20 20
AR3702
NC_1 D4 D4 D4 0
1/16W
2 21 21 21 FE_TS_DATA[4]
FE_TS_DATA[5] +3.3V_LNA +3.3V_TU +3.3V_Normal
IF_AGC D5 D5 D5 FE_TS_DATA[6]
3 22 22 22 FE_TS_DATA[7]
T2 L3701 L3704
SCL D6 D6 D6 UBW2012-121F UBW2012-121F
4 23 23 23 C3739 C3706 C3730 C3731 C3733 C3738
22uF 0.1uF 22uF 0.1uF 22uF 0.1uF
SDA D7 D7 D7 10V 16V 10V 16V 10V 16V
5 24 24 24
T2_OR_CHINA
IF[P] RESET_DEMOD RESET_DEMOD RESET_DEMOD R3719 IC3701
6 25 25 25 10
DEMOD_RESET
+3.3V_TU AP7361-Y-13
+1.2V_DEMOD
T2_OR_CHINA T2_OR_CHINA
IF[N] B3[+3.3V] B2[+3.3V] B3[+3.3V] C3716
0.1uF
+3.3V_DEMOD R3723
3.3K EN OUT
7 1 T2_OR_CHINA 5
26 26 26 16V
T2_OR_CHINA
T2_OR_CHINA C3725
C3721 C3723 T2_OR_CHINA
NC_2 SCL_DEMOD SCL_DEMOD SCL_DEMOD T2_OR_CHINA 100pF 0.1uF
1uF
10V
GND
2 T2_OR_CHINA R3737
8 27 27 27 R3711 22
DEMOD_SCL
50V 16V
T2_OR_CHINA
R3733
12K
1
T2_OR_CHINA
C3702 1%
ADJ/NC IN C3737
20pF R1
NC_3 B4[+1.1V] B3[+1.1V] B4[+1.1V] 50V +1.2V_DEMOD 3 4 10uF
9 28 28 28 T2_OR_CHINA 10V
C3713 C3729 T2_OR_CHINA
100pF 0.1uF C3732
T2_OR_CHINA 50V 16V
F22_OUTPUT NC_6 F22_OUTPUT R3707 T2_OR_CHINAT2_OR_CHINA
0.1uF
16V
29 29 29 0
LNB_TX
T2_OR_CHINA
A1 B1 SDA_DEMOD SDA_DEMOD SDA_DEMOD T2_OR_CHINA R3734
A1 B1 30 30 30 R3712 22
DEMOD_SDA
22K
1%
C3704
20pF R2
47 LNB 50V
T2_OR_CHINA Vo=0.8*(1+R1/R2)
31 C3709 LNB_OUT
0.1uF
50V GND seperation for CHINA tuner
A1 B1 A1 B1 GND
TU_GND_A
T2_OR_CHINA
SHIELD A1 B1 A1 B1 32
TU_GND_B
47 47
NON_CHINA
NON_CHINA
NON_CHINA
NON_CHINA
NON_CHINA
NON_CHINA
TU_GND_A
TU_GND_B
TU_GND_A
TU_GND_B
R3708
R3713
R3715
R3718
R3720
R3721
C3712 C3701
1000pF 1000pF
A1 B1 630V
0
630V
CHINA
SHIELD SHIELD A1 B1 CHINA
47
TU_GND_A
TU_GND_B
+3.3V_TU +3.3V_DEMOD
T2_OR_CHINA
L3702
47 BLM18PG121SN1D
T2_OR_CHINA T2_OR_CHINA T2_OR_CHINA

C3724 C3734 C3727
0.1uF 10uF 0.1uF
16V
10V 16V
ERROR & VALID PIN

T2_OR_CHINA
R3736
FE_TS_VAL 0
FE_TS_VAL_ERR
FE_TS_ERR
GPIO must be added.

THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. TUNER_EU 37
Downloaded
RS-232C 4PIN & MSTAR DEBUG 4PIN
RS-232C 4PIN
RS232C_DEBUG_4P
+3.5V_ST P4000
12507WS-04L
R4001
100 VCC
1
PM_TXD
R4000
100 PM_RXD
2
PM_RXD
GND
3
RM_TXD
4
GND
MSTAR DEBUG 4PIN
MSTAR_DEBUG_4P
P4001
JP_GND1
JP_GND2
JP_GND3
JP_GND4
12505WS-04A00
3 RGB_DDC_SCL
4 RGB_DDC_SDA

FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS L14_S7LR(M1A) 2013/04/30
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. RS232C_MSTAR_DEBUG_4P 40
Downloaded
TP for EU
RF_SWITCH_CTL HDMI_ARC HP_ROUT CI_DET EPHY_RP SENSOR_SCL FRC_RESET

IF_AGC_SEL CK+_HDMI2 HP_LOUT /CI_CD1 EPHY_TN SENSOR_SDA DEMOD_RESET
CK-_HDMI2 SIDE_HP_MUTE /CI_CD2 EPHY_TP
SPDIF_OUT D0+_HDMI2 HP_DET EPHY_RN
AV2_CVBS_DET D0-_HDMI2
5V_DET_HDMI_2 D1+_HDMI2
D1-_HDMI2
D2+_HDMI2
D2-_HDMI2
DDC_SDA_2
DDC_SCL_2
HPD2

FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS NC5_M1A 2013/04/29
TP_EU 41
Downloaded
IR/LED + Digital Eye + Control
+3.5V_ST
R4603 R4604
10K 10K
1% 1%
R4601
100 P4600 OPT
KEY1
OPT 12507WR-10L P4601
C4602 12507WR-08L
0.1uF
16V
R4602 1
100 1
KEY2
OPT
C4603 2
0.1uF 2
+3.5V_ST 16V
3
L4600 3
BLM18PG121SN1D
4
4
R4606
+3.5V_ST C4600 C4601 1.8K
0.1uF 1000pF LED_R/BUZZ 5
16V 50V 5
VA4600
LED_R_Zener
R4600 6
3.3K 6
IR 7
C4604 7
VA4601
100pF IR_Zener
50V 8
8
9 9
+3.3V_Normal
10
Digital Eye Digital Eye OPT 11

R4605 R4607 C4605
1K 1K 18pF
50V
R4608 100
SENSOR_SCL
Digital Eye
R4609 100
SENSOR_SDA
Digital Eye OPT
C4606
18pF
50V

THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. IR_EYE_SENSOR 46
Downloaded
NAND FLASH MEMORY +3.5V_ST PM MODEL OPTION
<CHIP Config>
IC102 (SPI_SDI, PM_LED, PWM_PM)
H27U1G8F2CTR-BC R177
LG-NonOS SB51_ExtSPI 3’b000 51boot from SPI 10K PM_MODEL_OPT_0
LG-OS HEMCU_ExtSPI 3’b001 MIPS boot from SPI LCD - HIGH : LCD
+3.3V_Normal +3.3V_Normal +3.5V_ST PM_MODEL_OPT_0
NC_1 NC_29 R176 - LOW :: PDP
1 NAND_FLASH_1G_HYNIX
48 10K
PDP PM_MODEL_OPT_1
NC_2 NC_28 M1A_256M
2 EAN35669103 47 M1A_128M
- Not Use (Ready) IC101
NC_3 NC_27 PCM_A[0-7] IC101-*1
4.7K
LGE2132(M1A_256M)
4.7K
2.7K
3 46 LGE2131(M1A_128M)
22
NC_4 NC_26 I2C
OPT
OPT
4 45 AR101 +3.3V_Normal
NC_5 I/O7 PCM_A[7]
R115
R117
R165
5 44 U19 D5
RXA4+ LVA4P/TTL_B[0]/HCONV/GPIO170 U19 D5
NC_6 I/O6 PCM_A[6] SAR0/GPIO35 KEY1 LVA4P/TTL_B[0]/HCONV/GPIO170 SAR0/GPIO35
6 43 R140 R141 R144 R145 T20 F8 T20 F8
AR103 R107 R109 1K 1K 2.2K 2.2K RXA4- LVA4M/TTL_B[1]/E_O/GPIO171 SAR1/GPIO36 KEY2
22 T21 E7 LVA4M/TTL_B[1]/E_O/GPIO171 SAR1/GPIO36
1K 3.9K R/B I/O5 PCM_A[5] LED_R/BUZZ RXA3+ T21 E7
7 42 I2C_SDA LVA3P/TTL_B[2]/FB/GPIO172 SAR2/GPIO37 PM_MODEL_OPT_0 LVA3P/TTL_B[2]/FB/GPIO172 SAR2/GPIO37
T19 E6 T19 E6
RE I/O4 PCM_A[4] PM_LED I2C_SCL RXA3- LVA3M/TTL_B[3]/OPT_P/GPIO173 SAR3/GPIO38 PANEL_CTL LVA3M/TTL_B[3]/OPT_P/GPIO173
/F_RB R21 D6 SAR3/GPIO38
8 41 RXACK+ R21 D6
AMP_SDA LVACKP/TTL_B[4]/MCLK/GPIO174 SAR4/GPIO39 SCART1_MUTE LVACKP/TTL_B[4]/MCLK/GPIO174 SAR4/GPIO39
/PF_OE CE NC_25 SPI_SDI R20 R20
9 40 AMP_SCL RXACK- LVACKM/TTL_B[5]/GCLK/GPIO175
/PF_CE0 R19 W10 LVACKM/TTL_B[5]/GCLK/GPIO175
4.7K
4.7K
2.7K
RXA2+ R19 W10

NC_7 NC_24 LVA2P/TTL_B[6]/GST/GPIO176 GPIO_PM[13]/GPIO20 MHL_CD_SENSE LVA2P/TTL_B[6]/GST/GPIO176 GPIO_PM[13]/GPIO20
10 39 C102 P20 Y10 P20 Y10
R108 10uF RXA2- LVA2M/TTL_B[7]/POL/GPIO177 GPIO_PM[14]/GPIO21 /VBUS_EN
OPT
1K P3 LVA2M/TTL_B[7]/POL/GPIO177 GPIO_PM[14]/GPIO21
OPT
NC_8
11 38
NC_23 10V DIMMING PM_LED/GPIO4 PM_LED
P3
C101 P19 Y3 PM_LED/GPIO4
R116
R118
R121
RXA1+ P19 Y3
0.1uF VCC_1 VCC_2 LVA1P/TTL_G[0]/EPI0+/GPIO178 GPIO_PM[0]/GPIO7 POWER_DET LVA1P/TTL_G[0]/EPI0+/GPIO178 GPIO_PM[0]/GPIO7
12 37 N20 Y5 N20 Y5
RXA1- LVA1M/TTL_G[1]/EPI0-/GPIO179 PM_SPI_SCZ2/GPIO_PM[10]/GPIO17 AMP_MUTE
C103 N21 W11 LVA1M/TTL_G[1]/EPI0-/GPIO179 PM_SPI_SCZ2/GPIO_PM[10]/GPIO17
VSS_1 VSS_2 R157 100 RXA0+ N21 W11
13 36 0.1uF PWM_DIM PWM2 LVA0P/TTL_G[2]/EPI1+/GPIO180 GPIO_PM[15]/GPIO22 INV_CTL LVA0P/TTL_G[2]/EPI1+/GPIO180 GPIO_PM[15]/GPIO22
R156 10K N19 D3 N19 D3
NC_9 NC_22 PWM0 RXA0- LVA0M/TTL_G[3]/EPI1-/GPIO181 GPIO_PM[4]/GPIO11 POWER_ON/OFF_1
M21 AA3 LVA0M/TTL_G[3]/EPI1-/GPIO181 GPIO_PM[4]/GPIO11
+3.3V_Normal 14 35 R103 10K RXB4+ M21 AA3
PWM3 LVB4P/TTL_G[4]/EPI2+/GPIO182 GPIO_PM[7]/GPIO14 RL_ON LVB4P/TTL_G[4]/EPI2+/GPIO182 GPIO_PM[7]/GPIO14
NC_10 NC_21 M20 W5 M20 W5
R105 15 34 RXB4- LVB4M/TTL_G[5]/EPI2-/GPIO183 GPIO_PM[8]/GPIO15 /FLASH_WP
NVRAM_RHOM M19 D4 LVB4M/TTL_G[5]/EPI2-/GPIO183 GPIO_PM[8]/GPIO15
1K RXB3+ M19 D4
OPT CLE NC_20 LVB3P/TTL_G[6]/EPI3+/GPIO184 PWM_PM/GPIO200 LED_R/BUZZ LVB3P/TTL_G[6]/EPI3+/GPIO184 PWM_PM/GPIO200
16 33 IC104 L20 L15 L20 L15
AR104
22
AR102 BR24G256FJ-3
RXB3- LVB3M/TTL_G[7]/EPI3-/GPIO185 PM_UART_TX/GPIO_PM[1]/GPIO8
Y11
PM_TXD LVB3M/TTL_G[7]/EPI3-/GPIO185 PM_UART_TX/GPIO_PM[1]/GPIO8
ALE I/O3 PCM_A[3] Y11
17 32 PM_UART_RX/GPIO_PM[5]/GPIO12 PM_RXD PM_UART_RX/GPIO_PM[5]/GPIO12
/PF_CE1 +3.3V_Normal EEPROM L19 L19
WE I/O2 PCM_A[2] RXBCK+ LVBCKP/TTL_R[0]/EPI4+/GPIO186
PF_ALE K20 LVBCKP/TTL_R[0]/EPI4+/GPIO186
18 31 A0 VCC RXBCK- K20
LVBCKM/TTL_R[1]/EPI4-/GPIO187 LVBCKM/TTL_R[1]/EPI4-/GPIO187
/PF_WE WP I/O1 PCM_A[1] 1 8 K21 K21
19 30 C105 RXB2+ LVB2P/TTL_R[2]/EPI5+/GPIO188
/PF_WP K19 LVB2P/TTL_R[2]/EPI5+/GPIO188
0.1uF RXB2- K19
R102 R106 NC_11 I/O0 PCM_A[0] LVB2M/TTL_R[3]/EPI5-/GPIO189 LVB2M/TTL_R[3]/EPI5-/GPIO189
3.3K 1K 20 29 A1 WP J21 J21
2 7 RXB1+ LVB1P/TTL_R[4]/EPI6+/GPIO190
J20 LVB1P/TTL_R[4]/EPI6+/GPIO190
NC_12 NC_19 22 RXB1- LVB1M/TTL_R[5]/EPI6-/GPIO191 J20
21 28 J19 LVB1M/TTL_R[5]/EPI6-/GPIO191
A2 A0’h SCL RXB0+ LVB0P/TTL_R[6]/EPI7+/GPIO192 J19
NC_13 NC_18 3 6 R111 22 H20 LVB0P/TTL_R[6]/EPI7+/GPIO192
22 27 I2C_SCL H20
RXB0- LVB0M/TTL_R[7]/EPI7-/GPIO193 LVB0M/TTL_R[7]/EPI7-/GPIO193
NC_14 NC_17
23 26 GND SDA
4 5 R112 22
NC_15 NC_16 I2C_SDA
24 25 C104 C106
8pF 8pF
OPT OPT
EAN62389502
NAND_FLASH_2G_HYNIX NAND_FLASH_1G_TOSHIBA
EAN60708702 EAN61508001 NVRAM_ATMEL
IC102-*1 IC102-*2 IC104-*1
H27U2G8F2CTR TC58NVG0S3ETA0BBBH AT24C256C-SSHL-T M1A_256M M1A_128M
IC101 IC101-*1
A0 VCC LGE2132(M1A_256M) from CI SLOT LGE2131(M1A_128M)
NC_1 NC_29 NC_1 NC_29 1 8
1 48 1 48
NC_2 NC_28 NC_2 NC_28 A1 WP CI_TS_CLK
2 47 2 47 2 7 CI_TS_DATA[0-7]
NC_3 NC_27 NC_3 NC_27 Y1 V10 Y1 V10
3 46 3 46 GPIO78 TS0CLK/GPIO92 CI_TS_DATA[0] CI_TS_SYNC GPIO78 TS0CLK/GPIO92
A2 SCL W4 T14 W4 T14
3 6 CI_TS_VAL
NC_4 NC_26 NC_4 NC_26 5V_DET_HDMI_4 GPIO79 TS0DATA[0]/GPIO82 CI_TS_DATA[1] GPIO79 TS0DATA[0]/GPIO82
4 45 4 45 T13 T13
GND SDA
TS0DATA[1]/GPIO83 CI_TS_DATA[2] TS0DATA[1]/GPIO83
NC_5 I/O7 NC_5 I/O8 4 5 R184 22 K17 U13 K17 U13
5 44 5 44 I2C_SCL I2C_SCKM3/I2C_DDCR_CK/GPIO77 TS0DATA[2]/GPIO84 CI_TS_DATA[3] I2C_SCKM3/I2C_DDCR_CK/GPIO77 TS0DATA[2]/GPIO84
R183 22 J15 V15 J15 V15
NC_6 I/O6 NC_6 I/O7 I2C_SDA I2C_SDAM3/I2C_DDCR_DA/GPIO76 TS0DATA[3]/GPIO85 CI_TS_DATA[4] I2C_SDAM3/I2C_DDCR_DA/GPIO76 TS0DATA[3]/GPIO85
6 43 6 43 U8 U12 U8 U12
URSA/VCOM_SDA SDAM2/GPIO55 TS0DATA[4]/GPIO86 CI_TS_DATA[5] SDAM2/GPIO55 TS0DATA[4]/GPIO86
R/B I/O5 RY/BY I/O6 EAN61133501 T7 V13 T7 V13
7 42 7 42 URSA/VCOM_SCL SCKM2/GPIO56 TS0DATA[5]/GPIO87 CI_TS_DATA[6] SCKM2/GPIO56 TS0DATA[5]/GPIO87
U7 U14 U7 U14
RE I/O4 RE I/O5 SENSOR_SCL SCKM0/GPIO58 TS0DATA[6]/GPIO88 CI_TS_DATA[7] SCKM0/GPIO58 TS0DATA[6]/GPIO88
8 41 8 41 V7 T11 Internal demod out V7 T11
SENSOR_SDA SDAM0/GPIO59 TS0DATA[7]/GPIO89 SDAM0/GPIO59 TS0DATA[7]/GPIO89
CE NC_25 CE NC_25 T2_OR_CHINA F6 T12 F6 T12
9 40 9 40 R113 22 AMP_SCL I2S_IN_BCK/GPIO159 TS0SYNC/GPIO91 FE_TS_CLK I2S_IN_BCK/GPIO159 TS0SYNC/GPIO91
DEMOD_SCL G6 V12 G6 V12
R114 22 AMP_SDA I2S_IN_SD/GPIO160 TS0VALID/GPIO90 FE_TS_DATA[0-7] I2S_IN_SD/GPIO160 TS0VALID/GPIO90
NC_7 NC_24 NC_7 NC_24 AA4 Y14 AA4 Y14
10 39 10 39 DEMOD_SDA
T2_OR_CHINA TU_SCL I2C_SCKM1/GPIO80 TS1CLK/GPIO103 FE_TS_DATA[0] FE_TS_SYNC I2C_SCKM1/GPIO80 TS1CLK/GPIO103
NC_8 NC_23 NC_8 NC_23 Y4 Y16 Y4 Y16
11 38 11 38 TU_SDA I2C_SDAM1/GPIO81 TS1DATA[0]/GPIO93 FE_TS_DATA[1] FE_TS_VAL_ERR I2C_SDAM1/GPIO81 TS1DATA[0]/GPIO93
AA15 AA15
VCC_1 VCC_2 VCC_1 VCC_2 TS1DATA[1]/GPIO94 FE_TS_DATA[2] TS1DATA[1]/GPIO94
12 37 12 37 J6 Y13 J6 Y13
AV_CVBS_DET ET_TXD[0]/GPIO62 TS1DATA[2]/GPIO95 FE_TS_DATA[3] ET_TXD[0]/GPIO62 TS1DATA[2]/GPIO95
VSS_1 VSS_2 VSS_1 VSS_2 K6 AA16 K6 AA16
13 36 13 36 AV2_CVBS_DET EXT_TX_CLK/GPIO64 TS1DATA[3]/GPIO96 FE_TS_DATA[4] FE_TS_DATA[0] EXT_TX_CLK/GPIO64 TS1DATA[3]/GPIO96
W12 W12
TS1DATA[4]/GPIO97 FE_TS_DATA[0] TS1DATA[4]/GPIO97
NC_9 NC_22 NC_9 NC_22 G7 AA13 FE_TS_DATA[5] G7 AA13
14 35 14 35
COMP2_DET I2S_IN_WS/GPIO158 TS1DATA[5]/GPIO98 FE_TS_DATA[6] I2S_IN_WS/GPIO158 TS1DATA[5]/GPIO98
NC_10 NC_21 NC_10 NC_21 W14 W14
15 34 15 34 TS1DATA[6]/GPIO99 FE_TS_DATA[7] TS1DATA[6]/GPIO99
J4 W13 J4 W13
CLE NC_20 CLE NC_20 DEMOD_RESET ET_COL/GPIO60 TS1DATA[7]/GPIO100 ET_COL/GPIO60 TS1DATA[7]/GPIO100
16 33 16 33 J5 Y15 J5 Y15
MODEL_OPT_0 ET_TXD[1]/GPIO61 TS1SYNC/GPIO102 ET_TXD[1]/GPIO61 TS1SYNC/GPIO102
ALE I/O3 ALE I/O4 W15 W15
17 32 17 32 TS1VALID/GPIO101 TS1VALID/GPIO101
H19 H19
WE I/O2 WE I/O3 MODEL_OPT_1 LCK/GPIO194 LCK/GPIO194
18 31 18 31 G20 B3 R189 33 G20 B3
MODEL_OPT_2 LDE/GPIO195 PM_SPI_SCZ1/GPIO_PM[6]/GPIO13 /SPI_CS LDE/GPIO195 PM_SPI_SCZ1/GPIO_PM[6]/GPIO13
WP I/O1 WP I/O2 G19 A3 R188 33 G19 A3
19 30 19 30 /MHL_OCP_DET LHSYNC/GPIO196 PM_SPI_SCK/GPIO1 SPI_SCK LHSYNC/GPIO196 PM_SPI_SCK/GPIO1
G21 A4 G21 A4
NC_11 I/O0 NC_11 I/O1 FRC_RESET LVSYNC/GPIO197 PM_SPI_SCZ0/GPIO0 SIDE_HP_MUTE LVSYNC/GPIO197 PM_SPI_SCZ0/GPIO0
20 29 20 29 33 R182 C3 C3
PM_SPI_SDI/GPIO2 SPI_SDI PM_SPI_SDI/GPIO2
NC_12 NC_19 NC_12 NC_19 J17 A2 R190 33 J17 A2
21 28 21 28 HP_DET UART2_RX/GPIO69 PM_SPI_SDO/GPIO3 SPI_SDO UART2_RX/GPIO69 PM_SPI_SDO/GPIO3
J16 J16
NC_13 NC_18 NC_13 NC_18 SC1/COMP1_DET UART2_TX/GPIO70 UART2_TX/GPIO70
22 27 22 27 E8 B1 E8 B1
MHL_OCP_EN UART3_TX/GPIO52 RP EPHY_RP UART3_TX/GPIO52 RP
NC_14 NC_17 NC_14 NC_17 D7 C2 D7 C2
23 26 23 26 AMP_RESET UART3_RX/GPIO53 TN EPHY_TN UART3_RX/GPIO53 TN
U6 C1 U6 C1
NC_15 NC_16 NC_15 NC_16 MODEL_OPT_4 GPIO46[CTS] TP EPHY_TP GPIO46[CTS] TP
24 25 24 25 V6 B2 V6 B2
RF_SWITCH_CTL GPIO47[RTS] RN EPHY_RN GPIO47[RTS] RN
33 R181 K15 K15
/CI_CD1 UART1_TX/GPIO48 UART1_TX/GPIO48
L16 D2 L16 D2
/CI_CD2 UART1_RX/GPIO49 SPDIF_IN/GPIO161 5V_DET_HDMI_2 UART1_RX/GPIO49 SPDIF_IN/GPIO161
D1 R192 100 D1
+3.3V_Normal SPDIF_OUT/GPIO162 SPDIF_OUT SPDIF_OUT/GPIO162
NAND_FLASH_2G_TOSHIBA NAND_FLASH_1G_SS H5 SPDIF_OPTIC H5
USB1_CTL ET_TX_EN/GPIO63 ET_TX_EN/GPIO63
EAN60991001 EAN61857001 R180 K5 D8 K5 D8
IC102-*3 IC102-*4 10K MODEL_OPT_5 ET_RXD[0]/GPIO65 HWRESET SOC_RESET ET_RXD[0]/GPIO65 HWRESET
K4 E5 K4 E5
TC58NVG1S3ETA00 K9F1G08U0D-SCB0 R197 0 MODEL_OPT_6 ET_MDC/GPIO66 IRIN/GPIO5 IR ET_MDC/GPIO66 IRIN/GPIO5
CI_DET H6 G4 H6 G4
R178 22 USB1_OCD ET_MDIO/GPIO67 DDCA_CK/UART0_RX RGB_DDC_SCL ET_MDIO/GPIO67 DDCA_CK/UART0_RX
/PCM_CD L5 G5 L5 G5
PCM_A[0-14] ET_RXD[1]/GPIO68 DDCA_DA/UART0_TX RGB_DDC_SDA ET_RXD[1]/GPIO68 DDCA_DA/UART0_TX
NC_1 NC_29 NC_1 NC_29
1 48 1 48 PCM_A[0] U17 J18 U17 J18
NC_2 NC_28 NC_2 NC_28 PCM_A[1] PCMADR[0]/NF_AD[0]/GPIO130 PWM0/GPIO71 PWM0 PCMADR[0]/NF_AD[0]/GPIO130 PWM0/GPIO71
2 47 2 47 R18 K18 R18 K18
PCM_A[2] PCMADR[1]/NF_AD[1]/GPIO129 PWM1/GPIO72 PWM1 PCMADR[1]/NF_AD[1]/GPIO129 PWM1/GPIO72
NC_3 NC_27 NC_3 NC_27 V17 K16 V17 K16
3 46 3 46 PCM_A[3] PCMADR[2]/NF_AD[2]/GPIO127 PWM2/GPIO73 PWM2 PCMADR[2]/NF_AD[2]/GPIO127 PWM2/GPIO73
R16 L18 R16 L18
4 45 4 45 U16 L17 U16 L17
PCM_A[5] PCMADR[4]/NF_AD[4]/GPIO104 PWM4/GPIO75 PCM_5V_CTL PCMADR[4]/NF_AD[4]/GPIO104 PWM4/GPIO75
NC_5 I/O8 NC_5 I/O7 T17 T17
5 44 5 44 PCM_A[6] PCMADR[5]/NF_AD[5]/GPIO106 PCMADR[5]/NF_AD[5]/GPIO106
W18 T8 +3.3V_Normal W18 T8
NC_6 I/O7 NC_6 I/O6 PCM_A[7] PCMADR[6]/NF_AD[6]/GPIO107 NF_ALE/GPIO146 PF_ALE PCMADR[6]/NF_AD[6]/GPIO107 NF_ALE/GPIO146
6 43 6 43 U20 T9 U20 T9
PCM_A[8] PCMADR[7]/NF_AD[7]/GPIO108 NF_CEZ/GPIO142 /PF_CE0 PCMADR[7]/NF_AD[7]/GPIO108 NF_CEZ/GPIO142
RY/BY I/O6 R/B I/O5 Y19 U9 Y19 U9
7 42 7 42 PCM_A[9] PCMADR[8]/GPIO113 NF_CLE/GPIO141 /PF_CE1 L101 PCMADR[8]/GPIO113 NF_CLE/GPIO141
AA19 U11 BLM18PG121SN1D AA19 U11
RE I/O5 RE I/O4 PCM_A[10] PCMADR[9]/GPIO115 NF_RBZ/GPIO147 /F_RB PCMADR[9]/GPIO115 NF_RBZ/GPIO147
8 41 8 41 AA20 V9 AA20 V9
PCM_A[11] PCMADR[10]/GPIO119 NF_REZ/GPIO144 /PF_OE PCMADR[10]/GPIO119 NF_REZ/GPIO144
CE NC_25 CE NC_25 W21 U10 R193 C119 W21 U10
9 40 9 40 PCM_A[12] PCMADR[11]/GPIO117 NF_WEZ/GPIO145 /PF_WE 10K 0.1uF PCMADR[11]/GPIO117 NF_WEZ/GPIO145
V20 T10 V20 T10
NC_7 NC_24 NC_7 NC_24 PCM_A[13] PCMADR[12]/GPIO109 NF_WPZ/GPIO199 /PF_WP R196 PCMADR[12]/GPIO109 NF_WPZ/GPIO199
10 39 10 39 Y17 0 Y17
PCM_A[14] PCMADR[13]/GPIO112 IF_AGC_MAIN PCMADR[13]/GPIO112
NC_8 NC_23 NC_8 NC_23 V18 W2 C120 V18 W2
11 38 11 38 PCMADR[14]/GPIO111 IF_AGC CHINA 0.047uF PCMADR[14]/GPIO111 IF_AGC
V19 W1 C115 0.1uF R198 CHINA47 V19 W1
VCC_1 VCC_2 VCC_1 VCC_2 PCM_D[0-7] /PCM_CD PCMCD_N/GPIO135 SIFM 25V PCMCD_N/GPIO135 SIFM
12 37 12 37 W19 W3 C116 0.1uF R199 47 W19 W3
/PCM_CE PCMCE_N/GPIO120 SIFP C123 PCMCE_N/GPIO120 SIFP
VSS_1 VSS_2 VSS_1 VSS_2 PCM_D[0] U18 V2 CHINA CHINA 1000pF U18 V2
13 36 13 36 PCMDATA[0]/GPIO131 IM PCMDATA[0]/GPIO131 IM
PCM_D[1] V16 V1 ANALOG SIF OPT V16 V1
NC_9 NC_22 NC_9 NC_22 PCMDATA[1]/GPIO132 IP PCMDATA[1]/GPIO132 IP
14 35 14 35 PCM_D[2] W17 Close to MSTAR TU_SIF W17
PCMDATA[2]/GPIO133 PCMDATA[2]/GPIO133
NC_10 NC_21 NC_10 NC_21 PCM_D[3] Y20 AA2 R194 0 Y20 AA2
15 34 15 34 PCMDATA[3]/GPIO125 XIN IF_N_MSTAR PCMDATA[3]/GPIO125 XIN
PCM_D[4] R15 Y2 OPT R15 Y2
CLE NC_20 CLE NC_20 PCMDATA[4]/GPIO124 XOUT C117 C121 PCMDATA[4]/GPIO124 XOUT
16 33 16 33 PCM_D[5] AA18 0.1uF 100pF DTV_IF AA18
PCMDATA[5]/GPIO123 R195 0 PCMDATA[5]/GPIO123
ALE I/O4 ALE I/O3 PCM_D[6] T15 IF_P_MSTAR T15
17 32 17 32 PCMDATA[6]/GPIO122 C118 C122 C124 PCMDATA[6]/GPIO122
PCM_D[7] Y21 0.1uF 33pF 33pF Y21
WE I/O3 WE I/O2 PCMDATA[7]/GPIO121 TU_NON_ATSC TU_NON_ATSC PCMDATA[7]/GPIO121
18 31 18 31 W20 W20
/PCM_IORD PCMIORD_N/GPIO116 PCMIORD_N/GPIO116
WP I/O2 WP I/O1 V21 Close to MSTAR V21
19 30 19 30 /PCM_IOWR PCMIOWR_N/GPIO114 PCMIOWR_N/GPIO114
Y18 Y18
NC_11 I/O1 NC_11 I/O0 /PCM_IRQA PCMIRQA_N/GPIO110 XTAL_LOAD_22pF PCMIRQA_N/GPIO110
20 29 20 29 T16 T16
/PCM_OE PCMOE_N/GPIO118 PCMOE_N/GPIO118
R17 R17
R187
NC_12 NC_19 NC_12 NC_19

/PCM_REG
X101 C113 22pF
21 28 21 28 PCMREG_N/GPIO128 PCMREG_N/GPIO128
1M
T18 24MHz C114 22pF T18

NC_13 NC_18 NC_13 NC_18 PCM_RST PCM_RESET/GPIO134 PCM_RESET/GPIO134
22 27 22 27 W16 W16
/PCM_WAIT PCMWAIT_N/GPIO105 XTAL_LOAD_22pF PCMWAIT_N/GPIO105
NC_14 NC_17 NC_14 NC_17 U15 U15
23 26 23 26 /PCM_WE PCMWE_N/GPIO198 PCMWE_N/GPIO198
NC_15 NC_16 NC_15 NC_16 XTAL_LOAD_30pF XTAL_LOAD_27pF
24 25 24 25 C113-*1 30pF C113-*2 27pF
XTAL_LOAD_30pF XTAL_LOAD_27pF
C114-*1 30pF C114-*2 27pF

THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. MAIN1_EU 1
Downloaded
MODEL OPTION +3.3V_Normal
SOC_RESET +3.5V_ST
STby 3.5V Normal Power 3.3V DDR3 1.5V VDDC 1.05V +1.10V_VDDC
+1.10V_VDDC
MO_DVB_T2/C/S2
MO_DUALSTREAM
MO_S/W_EU/AJ
SWITCH_POSTEC
DDR_EXT:256
DDR_EXT:128
1K
1K
1K
1K
1K
1K
1K
L206
1K
MO_S/W_AJ
SW200-*1 BLM18PG121SN1D AVDD_NODIE +1.5V_DDR VDDC : 2026mA

MO_M120
TMSV153BRA +3.3V_Normal VDD33

MO_HD
+1.10V_VDDC
2
C289 C286 C252 +1.10V_VDDC

POWER_DET_RESET +3.5V_ST SWITCH_NAMAE 10uF 0.1uF 0.1uF AVDD_DDR0:55mA
SW200 C296 C210 C279
L204 10uF 0.1uF 0.1uF
R291
R222
R221
R206
R208
R211
R226
R290
JTP-1127WEM
0.1uF
0.1uF
0.1uF
BLM18PG121SN1D 10V
2
10uF
0.1uF
1
10V
1uF
OPT
0.1uF
0.1uF
0.1uF
0.1uF
10V
10V
0.1uF
1uF
1uF
R201 OPT 100 R266 L207
IF_AGC_SEL MODEL_OPT_0 470 SWITCH
10V
10V
R202 OPT 100 R205 BLM18PG121SN1D AVDD_DMPLL

MODEL_OPT_1 100
C275
C248
C207
C254
1
C278
C228
C266
R203 OPT 100
10uF
10uF
OPT C288 C205
C277
C280
C283
MODEL_OPT_2
C284
10uF
C204
10uF
C202 C200 10uF 0.1uF

C209
C235
C245
R204 OPT 100

C255
C259
AUD_LRCH 4.7uF 4.7uF R217

R225 OPT 100 10V 10V 0
MODEL_OPT_4
R228 OPT 100 L208 AVDD_DDR1:55mA
MODEL_OPT_5 SOC_RESET BLM18PG121SN1D AVDD_AU33
R230 OPT 100
MODEL_OPT_6
OPT 100
DDR_EXT:128 or NON
DDR_EXT:256 or NON
R229 AUD_LRCK R200 C201 C240 C287 C241

MO_DUALSTREAM_NON
470K 0.1uF 0.1uF 10uF 0.1uF

MO_S/W_NON_AJ
1K
MO_S/W_TW/CN
1K
1K
1K
1K
1K
1K
1K
MO_DVB_T/C
MO_M120_NON
MO_FHD
R212
R294
R293
R224
R223
R207
R209
R227
MODEL OPTION
PIN NAME PIN NO. LOW HIGH
MODEL_OPT_0 J5 MO_FHD MO_HD
MODEL_OPT_1 H19 MO_S/W_NON_AJ MO_S/W_AJ
MODEL_OPT_2 G20 MO_DVB_T/C MO_DVB_T2/C/S2

AUD_LRCH G19 MO_M120_NON MO_M120
MODEL_OPT_4 U6 DDR_EXT:256 or NON DDR_EXT : 128
MODEL_OPT_5 K5 MO_S/W_TW/CN MO_S/W_EU/AJ
M1A_256M M1A_128M
MODEL_OPT_6 K4 DDR_EXT:128 or NON DDR_EXT : 256 IC101 IC101-*1
LGE2132(M1A_256M) LGE2131(M1A_128M)
AUD_LRCK L5 MO_DUALSTREAM_NON MO_DUALSTREAM
* Dual Stream is only Korea 3D spec

R4 U3 R4 U3
AVDD_AU33 AVDD_AU33 AUVRM AUVRM AVDD_AU33 AUVRM
L11 A6 L11 A6
AVDD_DDR0_CLK GND_1 AVDD_DDR0_CLK GND_1
Memory OPTION L13
M11
AVDD_DDR1_CLK
AVDD_DDR0_CMD
GND_2
GND_3
A13
A15
L13
M11
AVDD_DDR1_CLK
AVDD_DDR0_CMD
GND_2
GND_3
A13
A15
Memory Auto K13 A18 K13 A18
MODEL_OPT_4 MODEL_OPT_6 C5
AVDD_DDR1_CMD GND_4
B12 C5
AVDD_DDR1_CMD GND_4
B12
INT+EXT Det +1.5V_DDR
AVDD_DDR0_D_1 GND_5 AVDD_DDR0_D_1 GND_5
K12 B14 K12 B14
128M Only 0 0 0 L12
AVDD_DDR0_D_2 GND_6
B16 L12
AVDD_DDR0_D_2 GND_6
B16
C6 B17 C6 B17
256M Only 1 0 0 K14
AVDD_DDR1_D_1 GND_8
B19 K14
AVDD_DDR1_D_1 GND_8
B19
L14 B20 L14 B20
128M+128M 0 1 0 B5
AVDD_DDR1_D_3 GND_10
C9 B5
C9
AVDD_DRAM_1 GND_11 AVDD_DRAM_1 GND_11
B6 C10 B6 C10
128M+256M 0 0 1 R8
AVDD_DRAM_2 GND_12
C21 R8
AVDD_DRAM_2 GND_12
C21
AVDD_NODIE AVDD_DVI_USB_MPLL_1 GND_13 AVDD_DVI_USB_MPLL_1 GND_13
R9 D9 R9 D9
256M+256M 1 0 1 L7
AVDD_DVI_USB_MPLL_2 GND_14
E20 L7
E20
VDD33 AVDD_MOD_1 GND_15 AVDD_MOD_1 GND_15
L8 F9 L8 F9
AVDD_MOD_2 GND_16 AVDD_MOD_2 GND_16
P8 F11 P8 F11
AVDD_NODIE AVDD_NODIE GND_17 AVDD_NODIE GND_17
K9 F13 K9 F13
VDD33 AVDD_PLL GND_18 AVDD_PLL GND_18
Country Option AVDD_DMPLL
+1.10V_VDDC
R5
P11
AVDD3P3_DMPLL
AVDDL_MOD
GND_19
GND_20
F15
F17
R5
P11
AVDD3P3_DMPLL
AVDDL_MOD
GND_19
GND_20
F15
F17
C7 F19 C7 F19
MODEL_OPT_1 MODEL_OPT_5 +1.10V_VDDC DVDD_DDR_1 GND_21 DVDD_DDR_1 GND_21
M13 F21 M13 F21
1uFC260 DVDD_DDR_2 GND_22 DVDD_DDR_2 GND_22
R6 G8 R6 G8
DVDD_NODIE GND_23 DVDD_NODIE GND_23
TW 0 0 A7 G9 A7 G9
DVDD_RX_1_1 GND_24 DVDD_RX_1_1 GND_24
M12 G10 M12 G10
B7 G11 B7 G11
EU 0 1 DVDD_RX_2_1 GND_26 DVDD_RX_2_1 GND_26
M14 G12 M14 G12
N11 G13 N11 G13
+1.10V_VDDC VDDC_1 GND_28 VDDC_1 GND_28
CN 1 0 N12 G14 N12 G14
VDDC_2 GND_29 VDDC_2 GND_29
N13 G15 N13 G15
N14 G16 N14 G16
AJ 1 1 VDDC_4 GND_31 VDDC_4 GND_31
N15 G17 N15 G17
P12 G18 P12 G18
P13 H7 P13 H7
P14 H8 P14 H8
L9 H9 L9 H9
VDD33 VDDP GND_36 VDDP GND_36
H10 H10
GND_37 GND_37
AA10 H11 AA10 H11
AVDD5V_MHL AVDD5V_MHL GND_38 AVDD5V_MHL GND_38
H12 H12
GND_39 GND_39
H13 H13
GND_40 GND_40
H14 H14
GND_41 GND_41
H15 H15
GND_42 GND_42
H16 H16
GND_43 GND_43
H17 H17
GND_44 GND_44
M1A_256M M1A_128M H18 H18
GND_45 GND_45
IC101 IC101-*1 J7 J7
GND_46 GND_46
LGE2132(M1A_256M) LGE2131(M1A_128M) J8 J8
GND_47 GND_47
J9 J9
GND_48 GND_48
J10 J10
GND_49 GND_49
HDMI1_ARC HDMI1_ARC J11 J11
M4 T6 M4 T6 GND_50 GND_50
DTV/MNT_VOUT J12 J12
HDMI
HDMI_ARC ARC0 CVBSOUT1 ARC0 CVBSOUT1

C212 1uF R231 0 W7 V5 0.047uF C236 33 R244 W7 V5 GND_51 GND_51
D0-_HDMI4 R214 10 RXC0N CVBS0 TU_CVBS RXC0N CVBS0 J13 J13
Y8 U5 0.047uF C237 33 R245 Y8 U5 GND_52 GND_52
D0+_HDMI4 R215 10 RXC0P CVBS1 SC1/AV2_CVBS_IN RXC0P CVBS1 J14 J14
W8 T5 0.047uF C238 33 R246 +3.3V_Normal W8 T5 GND_53 GND_53
D1-_HDMI4 RXC1N CVBS2 COMP2_Y+/AV_CVBS_IN RXC1N CVBS2 K8 K8
Y9 V4 0.047uF C239 68 R247 C242 Close Y9 V4 GND_54 GND_54
D1+_HDMI4 RXC1P VCOM 1000pF
to MSTAR RXC1P VCOM K10 K10
AA9 R213 R210 I2S_I/F AA9 GND_55 GND_55
D2-_HDMI4 RXC2N 50V 10K 10K RXC2N K11 K11
W9 E4 OPT OPT OPT W9 E4 GND_56 GND_56
D2+_HDMI4 RXC2P I2S_OUT_BCK/GPIO165 AUD_SCK RXC2P I2S_OUT_BCK/GPIO165 L10 L10
AA7 F4 AA7 F4 GND_57 GND_57
CK-_HDMI4 RXCCKN I2S_OUT_MCK/GPIO163 R295 0 AUD_MASTER_CLK RXCCKN I2S_OUT_MCK/GPIO163 M5 M5
Y7 F7 Y7 F7 GND_58 GND_58
CK+_HDMI4 RXCCKP I2S_OUT_SD/GPIO166 AUD_LRCH RXCCKP I2S_OUT_SD/GPIO166 M7 M7
N2 F5 N2 F5 GND_59 GND_59
CEC_REMOTE_S7 CEC/GPIO6 I2S_OUT_WS/GPIO164 AUD_LRCK CEC/GPIO6 I2S_OUT_WS/GPIO164 M8 M8
E3 R216 R218 E3 GND_60 GND_60
DDC_SCL_2 DDCDA_CK/GPIO27 10K 10K DDCDA_CK/GPIO27 M9 M9
E2 C4 OPT OPT C208 E2 C4 GND_61 GND_61
DDC_SDA_2 DDCDA_DA/GPIO28 USB0_DM DDCDA_DA/GPIO28 USB0_DM M10 M10
W6 Y12 15pF W6 Y12 GND_62 GND_62
DDC_SCL_4 DDCDC_CK/GPIO31 USB1_DM SIDE_USB1_DM 50V DDCDC_CK/GPIO31 USB1_DM N4 N4
AA6 B4 OPT AA6 B4 GND_63 GND_63
DDC_SDA_4 DDCDC_DA/GPIO32 USB0_DP SIDE USB DDCDC_DA/GPIO32 USB0_DP N5 N5
L4 AA12 L4 AA12 GND_64 GND_64
HPD2 HOTPLUGA/GPIO23 USB1_DP SIDE_USB1_DP HOTPLUGA/GPIO23 USB1_DP N6 N6
Y6 Y6 GND_65 GND_65
HPD4 HOTPLUGC/GPIO25 HOTPLUGC/GPIO25 N7 N7
F1 J2 F1 J2 GND_66 GND_66
D0-_HDMI2 RXA0N BIN0M C221 0.047uF R232 68 RXA0N BIN0M N8 N8
G3 J3 G3 J3 GND_67 GND_67
D0+_HDMI2 RXA0P BIN0P C222 0.047uF R233 33 SC1_B+/COMP1_Pb+ RXA0P BIN0P N9 N9
G1 K3 G1 K3 GND_68 GND_68
D1-_HDMI2 RXA1N GIN0M C223 0.047uF R234 68 RXA1N GIN0M N10 N10
D1+_HDMI2 RXA1P GIN0P C224 0.047uF R235 33 SC1_G+/COMP1_Y+ RXA1P GIN0P P4 P4
H3 K2 H3 K2 GND_70 GND_70
D2-_HDMI2 RXA2N RIN0M C225 0.047uF R236 68 RXA2N RIN0M P5 P5
D2+_HDMI2 RXA2P RIN0P C226 0.047uF R237 33 SC1_R+/COMP1_Pr+ RXA2P RIN0P P6 P6
F3 M6 F3 M6 GND_72 GND_72
CK-_HDMI2 RXACKN HSYNC0 SC1_ID RXACKN HSYNC0 P7 P7
F2 L6 F2 L6 GND_73 GND_73
CK+_HDMI2 RXACKP VSYNC0 SC1_FB RXACKP VSYNC0 P9 P9
GND_74 GND_74
P10 P10
H/P OUT U4 L2 U4 L2 GND_75 GND_75
HP_LOUT EAR_OUTL BIN1M C227 0.047uF R238 68 EAR_OUTL BIN1M P15 P15
T4 L3 T4 L3 GND_76 GND_76
HP_ROUT EAR_OUTR BIN1P C229 0.047uF R239 33 COMP2_Pb+ EAR_OUTR BIN1P P16 P16
P2 M1 P2 M1 GND_77 GND_77
SC1/COMP1_L_IN 2.2uF C214 AUL1 GIN1M C230 0.047uF R240 68 AUL1 GIN1M P17 P17
R2 M2 R2 M2 GND_78 GND_78
AV2_L_IN AV2 2.2uF C203 AUL2 GIN1P C231 0.047uF R241 33 COMP2_Y+/AV_CVBS_IN AUL2 GIN1P P18 P18
T1 N1 T1 N1 GND_79 GND_79
COMP2_L_IN 2.2uF C216 AUL3 RIN1M C232 0.047uF R242 68 AUL3 RIN1M R10 R10
R3 N3 R3 N3 GND_80 GND_80
SC1/COMP1_R_IN 2.2uF C217 AUR1 RIN1P C233 0.047uF R243 33 COMP2_Pr+ AUR1 RIN1P R11 R11
AV2_R_IN AV2 2.2uF C206 AUR2 SOGIN1 C234 1000pF AUR2 SOGIN1 R12 R12
T3 OPT T3 GND_82 GND_82
COMP2_R_IN 2.2uF C219 AUR3 AUR3 R13 R13
U2 U2 GND_83 GND_83
SCART1_Lout AUOUTL0 AUOUTL0 R14 R14
V3 V3 GND_84 GND_84
SCART1_Rout AUOUTR0 AUOUTR0 K7 K7
AUDIO OUT T2 T2 GND_EFUSE GND_EFUSE
AUVAG AUVAG
C213 C220
1uF 4.7uF
AUVRM
L214
BLM18PG121SN1D

Downloaded
AUDIO AMP(TI)
AMP_COIL_GET AMP_COIL_GET AMP_COIL_GET AMP_COIL_GET

L5603-*1 L5604-*1 L5605-*1 L5606-*1
10.0uH 10.0uH 10.0uH 10.0uH
AMP_COIL_TAIYO AMP_COIL_TAIYO AMP_COIL_TAIYOAMP_COIL_TAIYO

L5603-*2 L5604-*2 L5605-*2 L5606-*2
10.0uH 10.0uH 10.0uH 10.0uH
This parts are Located

+24V +24V_AMP
on AVSS area.
R5610
L5600
470
UBW2012-121F
C5611 4700pF
AMP_COIL_ABCO Close to Speaker

0.047uF
C5612
L5605
C5601 10uH
0.1uF
C5613 2200pF
SPK_L+
50V
C5616
0.033uF
50V
R5611
C5609 4700pF +24V_AMP 18
50V
C5608 R5609 C5626 OPT

OPT 330pF C5632 C5636
0.047uF 470 C5640 50V 0.1uF 2200pF
C5618 C5620
PVDD_AB_2
PVDD_AB_1
0.1uF 10uF 4.7uF 50V 50V

PLL_FLTP
PLL_FLTM
+3.3V_Normal 50V 35V 50V

SSTIMER
VR_ANA
3216 C5630
BST_A
OUT_A
0.47uF
AVSS
PBTL
NC_2
NC_1
OPT
C5627
50V C5637 SPEAKER_L
C5633 2200pF
330pF 50V
0.1uF
[EP] 50V
12
11
10
9
8
7
6
5
4
3
2
1
50V
AVDD 13 48 PGND_AB_2 R5612
+3.5V_ST 18
C5604 R5608 2K A_SEL_FAULT PGND_AB_1
THERMAL
14 47
0.1uF MCLK OUT_B
46
49
16V 15 SPK_L-
18K OSC_RES NC_6
16 45 50V L5606
TAS5733
IC5600
R5601 R5607 1% DVSSO 17 44 NC_5 0.033uF 10uH

10K VR_DIG BST_B C5624
AUD_MASTER_CLK 18 43 AMP_COIL_ABCO
R5603 PDN BST_C
19 42
C 100 LRCLK 20 41 NC_4 AMP_COIL_ABCO
OPT C5602 50V
OPT SCLK 40 NC_3 L5604
R5600 B 1000pF C5607 21 0.033uF 10uH
AMP_MUTE Q5600 50V SDIN OUT_C
0.1uF 22 39 C5625
10K MMBT3904(NXP) SPK_R+
SDA 23 38 PGND_CD_2
E
SCL PGND_CD_1 OPT SPEAKER_R
R5613
1/16W
24 37
C5634 C5638
C5631
25
26
27
28
29
30
31
32
33
34
35
36
0.1uF 2200pF
18
AUD_LRCK
OPT 0.47uF 50V
AUD_SCK 50V 50V
R3405
RESET
STEST
DVDD
DVSS
GND
AGND
VREG
GVDD_OUT
BST_D
PVDD_CD_1
PVDD_CD_2
OUT_D
0 AUD_LRCH C5628 OPT

POWER_DET AMP_SDA 330pF C5639
+24V_AMP 50V 2200pF
AMP_SCL C5635
0.1uF 50V
C5629 50V
C5614
C56151uF 25V
0.1uF OPT 330pF

AMP_RESET C5641 50V
+3.3V_Normal C5619 C5621
0.1uF 10uF 4.7uF
R5614
1/16W
50V 35V 50V

3216
18
C5606 SPK_R-
ZD5600
0.1uF C5617 0.033uF

L5603
16V 50V
5V
10uH
OPT
C5610 AMP_COIL_ABCO
0.1uF
16V
WAFER-ANGLE
SPK_L+
4
SPK_L-
3
SPK_R+
2
SPK_R-
1
P5600

L14 2013.10.06
FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS
ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR AUDIO[TI] 56
Downloaded
L14 MHL SW AND GATE
+3.3V_Normal
MHL_SW_AND_GATE
IC5801
74LVC1G08GW
B VCC
1 5
MHL_CD_SENSE
A
2
MHL_OCP_EN
GND Y
3 4
MHL_5V_EN

THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. MHL_SW_AND 58
Downloaded
LD44B

L14 POWER BLOCK (POWER DETECT 2)
+24V +12V +3.5V_POWER_DET

OLD_18PIN +3.5V_ST
FROM LIPS or POWER B/D P401-*1

SMAW200-H18S1
R435
100K PD_+3.5V
Power_DET PANEL_VCC
+3.5V_ST OPT OPT R454-*1 OPT +12V PANEL_VCC
R457 R430 R432 300
Q401 R438
8.2K 2.7K 0
1% 5% 5% 4.7K
MMBT3906(NXP) PWR ON 1 2 DRV ON 1%
IC401
3.5V 3 4 PDIM#1 APX803D29
R454 L408
3.5V 5 6 3.5V 100 5% Q405
1 3 OPT VCC RESET UBW2012-121F
GND PDIM#2 3 2 POWER_DET DMP2130L
R412 7 8 120OHM
R406
D
10K 2 33K 24V 9 10 24V C415 1
R431 C422
+3.5V_ST GND 11 12 GND 0.1uF 1.2K GND OPT
R404 16V POWER_DET_RESET 0.1uF C425 R445 C427 R451 R452
12V 13 14 12V 1% 10uF 5.6K 5.6K
4.7K 0.1uF 33K G
12V 15 16 N.C 25V 16V
OPT OPT
R400 GND 17 18 GND +3.5V_POWER_DET R436
10K C Q400 +24V
100K
R402 R446
10K B MMBT3904(NXP)
12K
RL_ON 19
OPT
OPT OPT
R401 R455 R427 R458 IC402
E +3.3V_Normal 27K 0 APX803D29 OPT R442 C
10K 0 R437
1% 5% 100 5% 10K B Q403
OPT VCC 3 2 RESET PANEL_CTL
R456 MMBT3904(NXP)
0 +3.5V_ST OPT 1
R420 OPT R441 E
1K C413 R428 GND 10K
ZD404 0.1uF 5.1K
5V R419 16V 1%
100 R426
+3.5V_POWER_DET NEW_18PIN 10K
P401
SMAW200-H18S5
C
R425 Ready - Dual Power Det Power Detect activity
B 10K
L400 INV_CTL
CB2012PK501T
+3.5V_ST Detect Valtage Now is Use Circuit Designator FET_2.5V_DIODE
E Q402
PWR ON 1 2 DRV ON MMBT3904(NXP) Q406-*1
L401
C407
10uF
10V
C400
1uF
10V
ZD400
5V
CB2012PK501T 3.5V
3.5V
3 4 PDIM#1
3.5V
PWM_DIM Power Detect +3.5V R432, R454-*1, R438 +3.3V_Normal DMP2130L
D
2012 1005 5 6
OPT GND PDMI#2
L402 7 8 PWM1 * Notice Power Detect +12V O R430, R431, R454
MLB-201209-0120P-N2 24V 24V
+24V 9 10 PWM_DIM_PULL_DOWN PWM2_2CH_POWER
OPT
- Applying all inch models for LCD L14 +3.5V_ST +3.3V_Normal
G
+24V_CAP GND GND R424 R423
C401 11 12
100
R467 - Dual Power Det is used Power Detect +24V R457, R454
C432 12V 12V 3.9K 1K
4.7uF 0.1uF 13 14 for detecting two kinds of voltage
50V 12V NC FET_2.5V_AOS
50V 15 16
Q406 L410
3216 GND 17 18 GND
L403 AO3435 BLM18PG121SN1D
MLB-201209-0120P-N2
+12V
D
+12V_CAP
C433
4.7uF
C402
0.1uF
19
+1.10V_VDDC
.
C428 C429 C430
G
16V 16V R443 R447 ZD402
+3.5V_ST 10K 22K 2.2uF 0.1uF 22uF
3216 5V
IC403 +3.3V_Normal 10V 16V 10V
L406 TPS5432DDAR [EP]GND
CB2012PK501T
C418
OPT 0.01uF
C437 C436 C414 C435 BOOT SS R429 R448
1 8 2.2K
0.1uF 10uF 10uF 0.1uF 10K
THERMAL
16V 10V 10V 16V

+1.10V_VDDC VIN EN
9
2 7 C
+1.5V_DDR Vout=1.25*(1+R2/R1)+Iadj*R2 L407 C417

0.1uF
POWER_ON/OFF_1
R444
10K B Q404
3.6uH PH COMP MMBT3904(NXP)
16V 3 6 C416
+3.3V_Normal +1.5V_DDR 3A 0.33uF E
OPT R433 16V
ZD401 C424 C421 C420 GND VSENSE 2.7K
22uF 22uF 4 5
L409 IC404 L411 2.5V 0.1uF 1%
AZ1117EH-ADJTRG1 16V 10V 10V C419 C434
BLM18PG121SN1D CB2012PK501T C423 R439 0.039uF 390pF
50V 20K
R1 50V 50V
270pF 1%
IN OUT
ADJ/GND
C426 R449 R453 ZD403
10uF 1K R1 0 2.5V R440 R2
10V 1/16W 47K
1% C431 1%
10uF
1.3A R450
200
1/16W R2
10V
1%
Vout=0.808*(1+R1/R2)
+5V_Normal & +5V_USB with OCP

+12V
C405 C406
10uF 10uF
16V
[EP]GND
PGND_2
PGND_1
PGOOD
VIN_2
VIN_1
OPT R410
V7V
100K
C403
100pF +5V_Normal
50V C409 L405
24
23
22
21
20
19
0.047uF 4.7uH
EN BST 25V
C404
R408 4700pF 1 18
4.7K 50V THERMAL
+3.3V_Normal COMP 25
LX_2 R421 C411 C412
2 17 18K 82pF 22uF
+3.3V_Normal OPT SS LX_1 1% 50V 16V
R459 3 16
OPT OPT 0 IC400 R1
ROSC FB
R403 R405 4 15
4.7K 4.7K TPS65282REGR
EN_SW2 SW_IN_2 R2
MHL_5V_EN 5 14
MHL_SW_TR
R463
MHL_SW_TR
R464
USB1_CTL
EN_SW1
6
4A 13
SW_IN_1
R422
3.3K
2.7K 10K 1%
10
11
12
7
MHL_SW_TR +3.3V_Normal C410

+5V_USB 10uF
Q408 10V
FAULT2
FAULT1
SW_OUT2
RLIM
AGND
SW_OUT1
E C
MHL_5V_EN R407 R409
MHL_SW_TR 10K 10K
C
R461 R415 5V_HDMI_4 AVDD5V_MHL
10K B R466
B 15K
/VBUS_EN 20K
5%
D401 R418
(Active Low) MHL_SW_TR MBR230LSFT1G
E MHL_SW_TR
Q407 R465 30V 10
10K
MHL_SW_TR C OPT C408
R462 R416 10uF
10K
/MHL_OCP_DET
USB1_OCD
B 100K 10V
MHL_OCP_EN
MHL_SW_TR
(Active High) Q409 E
Vout=0.8*(1+R1/R2)

THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. Power_PD2 4
Downloaded
USB (SIDE)
+5V_USB
JK700
ZD700 C700 C703
SD05 22uF 22uF
3AU04S-305-ZC-(LG)
5V 10V 10V
USB DOWN STREAM
OPT OPT
2
SIDE_USB1_DM
3
SIDE_USB1_DP
OPT OPT OPT
C701 C702 D700
5pF 5pF RCLAMP0502BA
4
50V 50V
5

THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. USB_S1 7
Downloaded
SPDIF
SPDIF OPTIC JACK

+3.3V_Normal
5.15 Mstar Circuit Application
JK1001
JST1223-001
GND
1
Fiber Optic
VCC
2
VINPUT
3
SPDIF_OUT
4
SPDIF_CAP_68pF SPDIF_CAP_47pF
C1001 C1002 C1002-*1
FIX_POLE
OPT 1uF 68pF 47pF

10V 50V 50V
ESD Ready

FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS NC5_L14 2013/05/15
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. SPDIF 10
Downloaded
Serial Flash for SPI boot
+3.5V_ST +3.5V_ST
SPI_FLASH_MACRONIX
OPT IC1300
R1301
+3.5V_ST 4.7K MX25L8006EM2I-12G
C1300
CS# VCC 0.1uF
/SPI_CS 1 8
OPT
R1300
10K SO/SIO1 HOLD#
SPI_SDO 2 7
WP# SCLK
/FLASH_WP 3 6 SPI_SCK
R1302
GND SI/SIO0 33
4 5 SPI_SDI
SPI_FLASH_WINBOND
IC1300-*1
W25Q80BVSSIG
CS VCC
1 8
DO[IO1] HOLD[IO3]
2 7
%WP[IO2] CLK
3 6
GND DI[IO0]
4 5

THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. S_FLASH 13
Downloaded
LVDS_EU
FOR FHD REVERSE(10bit)

[51Pin LVDS Connector] [30Pin LVDS Connector]
(For FHD 60Hz) Change in S7LR
(For HD 60Hz_Normal)
MO_FHD MIRROR Pol-change
P1800
FI-RE51S-HF-J-R1500 RXA4+ RXA0+ RXA0- MO_HD
RXA4- RXA0- RXA0+ P1801
10031HR-30
RXA3+ RXA1+ RXA1-
1
RXA3- RXA1- RXA1+
2
LVDS_SEL 1
RXACK+ RXA2+ RXA2-
3
2
+3.3V_Normal RXACK- RXA2- RXA2+
4 VCOM_SDA 3 VCOM_SDA
RXA2+ RXACK+ RXACK-
5 VCOM_SCL
OPT 4 VCOM_SCL
RXA2- RXACK- RXACK+
6 R1806
3.3K 5
RXA1+ RXA3+ RXA3-
7
6 RXA3+
OPT RXA1- RXA3- RXA3+
8
R1807 7
9 10K
8
RXA0- RXA4- RXA4+
10
9 RXACK+
11
10 RXACK-
11
12 RXA2+
13 RXA2-
14
16 RXACK+ RXBCK+ RXB2+ RXB2-
15 RXA1+
17 RXACK- RXBCK- RXB2- RXB2+
16 RXA1-
18 RXB2+ RXBCK+ RXBCK-
17
19 RXA2+ RXB2- RXBCK- RXBCK+ LVDS_SEL
18 RXA0+
20 RXA2- RXB1+ RXB3+ RXB3- +3.3V_Normal
19 RXA0-
21 RXB1- RXB3- RXB3+
20
22 RXB0+ RXB4+ RXB4- OPT
RXA1+ 21 R1808
3.3K
22
24 RXA0+ 23 OPT
R1809
25 RXA0- 10K
24
26 R1801 0
25 PANEL_VCC
MO_FHD
27
28
FOR FHD REVERSE(8bit) 26
RXB4+ 27
29 RXB4- Change in S7LR 28
30 RXB3+ 29
31 MIRROR Pol-change Shift
RXB3- 30
32 RXBCK+
RXA4- RXA4- RXA4+ RXA0+ 31
33 RXBCK-
34
RXA3- RXA0- RXA0+ RXA1+
35 RXB2+
RXACK+ RXA1+ RXA1- RXA2-
36 RXB2-
RXACK- RXA1- RXA1+ RXA2+
37
RXA2+ RXA2+ RXA2- RXACK-
38 RXB1+
RXA2- RXA2- RXA2+ RXACK+
39 RXB1-
RXA1+ RXACK+ RXACK- RXA3-
40 RXB0+
RXA1- RXACK- RXACK+ RXA3+
41 RXB0-
EU pin assign is different from NON EU.
42 R1802 0
MO_FHD
R1803 0 RXA0- RXA3- RXA3+ RXA4+
Because of position of HD wafer.
43
MO_FHD
44
45 RXB4+ RXB4+ RXB4- RXB0-

V-COM I2C
46 RXB4- RXB4- RXB4+ RXB0+
PANEL_VCC +3.3V_Normal
47 RXB3+ RXB0+ RXB0- RXB1- URSA/VCOM_SCL
48 RXB3- RXB0- RXB0+ RXB1+ URSA/VCOM_SDA
49 C1800 RXBCK+ RXB1+ RXB1- RXB2-

VCOM_I2C_PULL_UP VCOM_I2C_PULL_UP
0.1uF
50 16V RXBCK- RXB1- RXB1+ RXB2+ R1810 R1811
2K 2K
51 RXB2+ RXB2+ RXB2- RXBCK-
VCOM_I2C
RXB2- RXB2- RXB2+ RXBCK+ R1804
52 0
RXB1+ RXBCK+ RXBCK- RXB3- VCOM_SCL URSA/VCOM_SCL
R1805
0
RXB1- RXBCK- RXBCK+ RXB3+ VCOM_SDA URSA/VCOM_SDA
VCOM_I2C
RXB0+ RXB3+ RXB3- RXB4-
RXB0- RXB3- RXB3+ RXB4+

THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. LVDS_EU 18
Downloaded
CI Region * Option name of this page : CI_SLOT
(because of Hong Kong)
CI SLOT
+5V_CI_ON
CI_DATA[0-7]
CI TS INPUT
CI_DATA[0-7]
+5V_Normal AR1903 33
C1903 FE_TS_DATA[7]
CI_MDI[7]
10uF FE_TS_DATA[6]
10V CI_MDI[6]
FE_TS_DATA[0-7]
R1908 FE_TS_DATA[5]
CI_MDI[5]
10K FE_TS_DATA[4]
CI_SLOT_JACK CI_MDI[4]
/CI_CD1 P1900
10067972-000LF
AR1904 33 FE_TS_DATA[3]
R1914 35 1 CI_MDI[3]
100 CI_DATA[3] FE_TS_DATA[2]
36 2 CI_MDI[2] FE_TS_DATA[1]
AR1900 CI_DATA[4]
CI_DATA[0-7]
33 37 3 CI_MDI[1] FE_TS_DATA[0]
CI_DATA[5] R1919
CI_TS_DATA[4] 38 4 10K CI_MDI[0]
CI_DATA[6]
CI_TS_DATA[5] 39 5
CI_DATA[7] FE_TS_DATA[0-7]
CI_TS_DATA[6] 40 6
R1917 R1921 33
CI_TS_DATA[7] 41 7 47 CI_MISTRT FE_TS_SYNC
CI_ADDR[10] /PCM_CE R1922 33
42 8 CI_MIVAL_ERR FE_TS_VAL_ERR
R1910 10K R1923 100
43 9 CI_OE CI_MCLKI FE_TS_CLK
CI_ADDR[11]
CI_IORD 44 10 +5V_Normal
CI_ADDR[9]
CI_IOWR 45 11
CI_ADDR[8]
46 12 R1920
CI_ADDR[13] 10K
CI_MDI[0] 47 13
CI_ADDR[14]
CI_MDI[1] 48 14
CI_MDI[2] 49 15 CI_WE
50 16 R1918 100
CI_MDI[3] /PCM_IRQA
51 17
GND
C1901
0.1uF
52
53
18
19
C1904
0.1uF
C1905
0.1uF
CI HOST I/F
CI_MDI[4]
GND
CI_MDI[5] 54 20
+5V_Normal CI_ADDR[12]
CI_MDI[6] 55 21 CLOSE TO MSTAR
CI_ADDR[7]
R1900 CI_MDI[7] 56 22 GND +3.3V_Normal
10K R1911 10K CI_ADDR[6]
57 23
R1903 CI_ADDR[5]
47 58 24
PCM_RST CI_ADDR[4]
R1904 47 CI_DET
/PCM_WAIT 59 25 IC1902
CLOSE TO MSTAR CI_ADDR[3]
REG 60 26 C1906
R1905 100 CI_ADDR[2]
CI_TS_CLK 61 27 0.1uF
R1906 33 CI_ADDR[1] 1OE BUFFER_ORG VCC 16V
CI_TS_VAL 62 28 1 20
R1907 33 CI_ADDR[0]
CI_TS_SYNC 63 29
CI_DATA[0]
64 30 1A1 2OE
AR1901 33 CI_DATA[1] 2 19
65 31 CI_ADDR[0-14] PCM_A[0]
CI_TS_DATA[0] CI_DATA[2] AR1902 AR1910
66 32 100
CI_TS_DATA[1] 2Y4 1Y1 100
67 33 3 18
68 34
G2 69 G1 CI_ADDR[5] 1A2 2A4 CI_ADDR[2]
PCM_A[1] 4 17 PCM_A[7]
R1912 CI_ADDR[4] CI_ADDR[3]
100
/CI_CD2 2Y3 1Y2
TC74LCX244FT
+5V_Normal GND 5 16
GND 1A3 2A3

PCM_A[2] 6 15 PCM_A[6]
C1900
2pF
R1909
50V 2Y2 1Y3
10K GND 7 14
CLOSE TO MSTAR
1A4 2A2
PCM_A[3] 8 13 PCM_A[5]
2Y1 1Y4
CI_MISTRT 9 12
CI_MIVAL_ERR
GND 2A1
10 11 PCM_A[4]
CI_MCLKI
CI DETECT +3.3V_Normal
OR_GATE_CI_PHILIPS
IC1900
74LVC1G32GW +3.3V_Normal
B 1 5 VCC
/CI_CD2
A 2
/CI_CD1 AR1905 33
GND 3 4 Y R1913 CI_DATA[0] PCM_D[0]
10K CI_DATA[1] PCM_D[1]
CI_DATA[0-7]
CI_DATA[2] PCM_D[2]
OR_GATE_CI_TI OR_GATE_CI_TOSHIBA R1924 CI_DATA[3] PCM_D[3]
IC1900-*1 IC1900-*2 0
SN74LVC1G32DCKR TOSHIBA ELECTRONICS KOREA CORPORATION
CI_DET
IC1902-*1
PCM_D[0-7]
A VCC IN_B VCC

1 5 1 5
/PCM_CD AR1906 33
B IN_A R1915 CI_DATA[4] PCM_D[4] 74LCX244FT
2 2
47 CI_DATA[5] PCM_D[5]
GND Y GND OUT_Y
3 4 3 4
CI_DATA[6] PCM_D[6]
1OE BUFFER_CI VCC
CI_DATA[7] PCM_D[7] 1 20
1A1 2OE
2 19
PCM_D[0-7]
CI_DATA[0-7] 2Y4 1Y1
CI POWER ENABLE CONTROL 3 18
1A2 2A4
4 17
AR1908 33
CI_ADDR[8] PCM_A[8] 2Y3 1Y2
CI_ADDR[9] PCM_A[9] 5 16
+5V_Normal IC1901
AP2151WG-7 +5V_CI_ON CI_ADDR[10] PCM_A[10]
L1900 CI_ADDR[11] PCM_A[11] 1A3 2A3
6 15
BLM18PG121SN1D
IN OUT
5 1
2Y2 1Y3
7 14
GND AR1909 33
2 CI_ADDR[12] PCM_A[12]
R1916 1A4 2A2
C1902 8 13
100K CI_ADDR[13] PCM_A[13]
R1902 1uF
100 EN FLG 10V CI_ADDR[14] PCM_A[14]
PCM_5V_CTL 4 3
/PCM_REG 2Y1 1Y4
REG 9 12
R1901
10K
GND 2A1
10 11
AR1907 33
CI_OE /PCM_OE
CI_WE /PCM_WE
CI_IORD /PCM_IORD
CI_IOWR /PCM_IOWR

THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. PCMCI 19
Downloaded
Close to the tuner
NETCAST5.0_EU_TUNER_T/C
+3.3V_TU +3.3V_Normal
GND
L2600
UBW2012-121F
C2612 C2613
22uF 0.1uF
10V 16V
TU2600
TDJH-G101D
TU_I2C_FILTER TU_I2C_FILTER
R2607-*1 R2608-*1
MLG1005SR27JT MLG1005SR27JT
+3.3V_TU
B1[+3.3V]
1
C2608 C2609
NC_1 100pF
50V
0.1uF
16V
2
+3.3V_TU
IF_AGC
3 IF_AGC_MAIN
C2606
R2602 R2603
SCL 0.1uF
16V
should be guarded by ground
TU_I2C_NON_FILTER 1K 1K
4 C2601
R2607 33
C2605
TU_SCL
20pF 20pF
SDA 50V
TU_I2C_NON_FILTER
50V
5 R2608 33
C2602 C2607
TU_SDA
20pF 20pF
IF[P] R2604
50V 50V
6 10
IF_P_MSTAR
IF[N] R2605
7 10
IF_N_MSTAR
NC_2
8
NC_3
9
A1 B1
A1 B1
47
TU_GND_B
SHIELD

TUNER_EU_T/C 26
Downloaded
SCART_COMPONENT
COMPONENT SCART AMP
+12V
JK2802
PPJ245N2-01
R2811 EU
6E [RD2]E-LUG 10K C2808
COMP2_R_IN
VA2804 R2803 R2816 IC2801 0.1uF
[RD2]O-SPRING 5.6V 470K 12K 50V
5E AZ4580MTR-E1
OPT
R2810 EU
4E [RD2]CONTACT 10K R2831
COMP2_L_IN 2.2K OUT1 8 VCC
R2815 DTV/MNT_L_OUT 1
[WH]O-SPRING
VA2803 R2802
470K 12K EU EU EU
5D 5.6V +3.3V_Normal EU
C2804 R2834 R2844
OPT OPT 33K IN1- 7 OUT2 2.2K
R2817 R2818 10uF R2832 2
[RD1]CONTACT 10K 1K 16V DTV/MNT_R_OUT
4C 470K EU
COMP2_DET R2841 EU
EU IN1+ IN2- 33K C2812
[RD1]O-SPRING VA2816 EU 3 6 OPT 10uF
5C R2836
COMP2_Pr+ 5.6V C2807 10K EU R2843 16V
VA2802 R2801 33pF 470K
OPT R2839
7C [RD1]E-LUG-S 5.5V 75 VEE 5 IN2+ 10K
4 EU
ESD_COMP C2810
[BL]O-SPRING EU 33pF
5B
COMP2_Pb+ R2835
VA2801 R2800 5.6K EU
[GN/YL]CONTACT 5.5V +3.3V_Normal SCART1_Lout R2840
4A 75 5.6K
ESD_COMP SCART1_Rout
R2812 R2814 330pF 220K
[GN/YL]O-SPRING 1K C2806 R2833
5A 10K EU EU
AV_CVBS_DET EU EU
VA2800 OPT R2842 C2811
C2800 220K 330pF
6A [GN/YL]E-LUG 5.6V
OPT 0.1uF
16V
COMP2_Y+/AV_CVBS_IN
R2804 CLOSE TO MSTAR
D2800-*1 D2800 75
ESD_COMP_ZENER_ROHM
ESD_COMP_ZENER_KEC CLOSE TO MSTAR
D2801-*1 D2801
ESD_COMP_ZENER_KEC ESD_COMP_ZENER_ROHM
FULL SCART +3.3V_Normal [SCART AUDIO MUTE] +3.5V_ST
R2819 DTV/MNT_L_OUT SCART_MUTE

10K R2837 SCART_MUTE
2K R2845
R2820 1K SCART_MUTE 10K
SC1/COMP1_DET Q2802
VA2815 EU MMBT3904(NXP)
5.6V R2850 1K
AV2_CVBS_DET
OPT AV2
SCART1_MUTE
SCART_MUTE
DTV/MNT_R_OUT R2838 SCART_MUTE
2K C2809
SCART_MUTE 0.1uF
Q2803
SC1/AV2_CVBS_IN MMBT3904(NXP)
EU
R2813 OPT
C2801
75 47pF
AV_DET 50V
22 VA2807
COM_GND 5.5V
ESD_SCART
21
SYNC_IN EU
L2800 AV2
20 CM2012FR22KT
SYNC_OUT 220nH JK2803
EU EU DTV/MNT_VOUT
19 PPJ231-01
SYNC_GND2 VA2808 EU C2815 C2816
VA2814 R2821 R2851
18 20V 5.6V 75 68pF 68pF 4 10K
SYNC_GND1 ESD_SCART 50V 50V EU AV2_R_IN_A AV2_R_IN_A AV2_R_IN
R2827 R2846 AV2
17 22 0
RGB_IO 5 AV2 VA2818 R2854 C2817 R2853
SC1_FB AV2_L_IN_A 1000pF 12K
16 5.6V 470K AV2
R_OUT AV2_LR_ZENER AV2 50V
7 OPT
15 SC1_R+/COMP1_Pr+
RGB_GND ESD_SCART
VA2810 R2807 R2852
14 75 EU 8
R_GND 20V 10K
R2822 AV2_L_IN_A AV2_L_IN
13 75 R2849 AV2
D2B_OUT 6 R2848 0
0 AV2 R2855
12 EU VA2819 R2856 C2818 12K
G_OUT 5.6V 470K 1000pF AV2
AV2_LR_ZENER AV2 50V
11 SC1_G+/COMP1_Y+ OPT
D2B_IN VA2811 R2808
10 20V 75
G_GND ESD_SCART EU
9 R2824
ID 15K R2847
0
8 SC1_ID AV2
B_OUT EU AV2_CVBS_DET
7 SC1_B+/COMP1_Pb+ R2828
AUDIO_L_IN VA2812 VA2817 VA2820
20V 3.9K 5.6V
20V R2805 OPT
6 75 ESD_SCART
B_GND ESD_SCART
5
AUDIO_GND EU
4
AUDIO_L_OUT R2826
10K
3 SC1/COMP1_L_IN
AUDIO_R_IN R2823
0
2 EU R2806 R2829
AUDIO_R_OUT VA2813 470K 12K
5.6V
EU
1
ESD_SCART
SC1/AV2_CVBS_IN
AV2_L_IN_A ZD2800-*1 ZD2800 AV2
EU EU C2819
AV2_CVBS_ZENER_KEC AV2_CVBS_ZENER_ROHM R2857 47pF
JK2801 R2825 75
10K ZD2801-*1 ZD2801 50V
PSC008-01 SC1/COMP1_R_IN
1608 AV2
R2858 AV2_CVBS_ZENER_KEC AV2_CVBS_ZENER_ROHM 1%
0 VA2809
EU 5.6V
ESD_SCART R2809 R2830
470K 12K
Size Check !!!
EU
AV2_R_IN_A
AV2
DTV/MNT_L_OUT
EU
VA2806 C2813
5.6V 1000pF
OPT 50V
DTV/MNT_R_OUT
EU
VA2805 C2814
5.6V 1000pF
OPT 50V

THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. SCART_ COMPONENT 28
Downloaded
Headphone
*Option : HEAD_PHONE_EU
HEAD_PHONE
L3000
5.6uH HEAD_PHONE
HP_LOUT
HEAD_PHONE C3000 OPT C
C3004 HEAD_PHONE E
10uF C3002 R3002
4.7uF 16V 1000pF Q3002 B Q3004
1K MMBT3904(NXP)
10V 50V MMBT3904(NXP) B OPT HEAD_PHONE
OPT JK3000
+3.5V_ST E +3.3V_Normal
C KJA-PH-0-0177
GND 5
E
OPT OPT HEAD_PHONE
Q3001 R3005
10K L 4
OPT MMBT3906(NXP)
C R3001 B
R3000 3.3K
1K B C DETECT 3
SIDE_HP_MUTE HP_DET
Q3000 R3004
MMBT3904(NXP) 1K
OPT E HEAD_PHONE R 1
HEAD_PHONE
L3001 HEAD_PHONE
5.6uH
HP_ROUT
HEAD_PHONE C3001 OPT HEAD_PHONE C E
C3005 10uF C3003 R3003
4.7uF 16V 1000pF Q3003 B Q3005
1K MMBT3904(NXP) MMBT3904(NXP)
10V 50V B
OPT OPT
E C

THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. HEAD_PHONE_EU 30
Downloaded
RS-232C 4PIN & MSTAR DEBUG 4PIN
RS-232C 4PIN
RS232C_DEBUG_4P
+3.5V_ST P4000
12507WS-04L
R4001
100 VCC
1
PM_TXD
R4000
100 PM_RXD
2
PM_RXD
GND
3
RM_TXD
4
GND
MSTAR DEBUG 4PIN
MSTAR_DEBUG_4P
P4001
JP_GND1
JP_GND2
JP_GND3
JP_GND4
12505WS-04A00
3 RGB_DDC_SCL
4 RGB_DDC_SDA

FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS L14_S7LR(M1A) 2013/04/30
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. RS232C_MSTAR_DEBUG_4P 40
Downloaded
TP for EU
RF_SWITCH_CTL HDMI_ARC HP_ROUT CI_DET EPHY_RP SENSOR_SCL FRC_RESET

IF_AGC_SEL CK+_HDMI2 HP_LOUT /CI_CD1 EPHY_TN SENSOR_SDA DEMOD_RESET
CK-_HDMI2 SIDE_HP_MUTE /CI_CD2 EPHY_TP
SPDIF_OUT D0+_HDMI2 HP_DET EPHY_RN
AV2_CVBS_DET D0-_HDMI2
5V_DET_HDMI_2 D1+_HDMI2
D1-_HDMI2
D2+_HDMI2
D2-_HDMI2
DDC_SDA_2
DDC_SCL_2
HPD2

FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS NC5_M1A 2013/04/29
TP_EU 41
Downloaded
HDMI (REAR 2 MHL)
HDMI_1
HDMI_2 MHL
VA4200 5V_HDMI_2 5V_DET_HDMI_2
ESD_HDMI1_VARISTOR
R4208
10K
R4203 VA4207 5V_HDMI_4 5V_DET_HDMI_4

ESD_HDMI
1K
C
ESD_HDMI R4210 R4217
VA4202 Q4200 B 10K
HPD2 HPD4
MMBT3904(NXP) 100
ESD_HDMI
E GND VA4210
GND
SHIELD
R4220 100
R4211 100 20 DDC_SDA_4
DDC_SDA_2
20 HP_DET R4221 100
R4212 100 19 DDC_SCL_4
HP_DET DDC_SCL_2
19 5V R4213
18 VA4211 VA4212
R4204 ESD_HDMI ESD_HDMI ESD_HDMI
R4214
18 5V ESD_HDMI
1.8K
3.3K
VA4204 VA4205 17 GND

R4206
1.8K
3.3K
17 GND
16 DDC_DATA
16 DDC_DATA R4209 0
HDMI_ARC 15 DDC_CLK HDMI_CEC
HDMI1_ARC VA4213
15 DDC_CLK VA4203
HDMI_CEC NC ESD_HDMI
ESD_HDMI 14
NC ESD_HDMI
14 CE_REMOTE
VA4206 13
D4205
EAG59023302
CE_REMOTE
13
D4203 12 CK- 1 10
EAG59023302
CK-_HDMI4
CK- 1 10
12 CK-_HDMI2
11 CK_GND 2 9
CK+_HDMI4
CK_GND 2 9
11 CK+_HDMI2
10
CK+ 3 8
CK+ 3 8
10
9
D0- 4 7
D0-_HDMI4
D0- 4 7
9 D0-_HDMI2
8
D0_GND 5 6
D0+_HDMI4
8
D0_GND 5 6 D0+_HDMI2 D0+
7 IP4294CZ10-TBR
D0+
7 IP4294CZ10-TBR D1- ESD_HDMI_IP4294
6
D1- ESD_HDMI_IP4294 D4206
6
D4204 5
D1_GND 1 10
D1-_HDMI4
D1_GND 1 10
5 D1-_HDMI2
4
D1+ 2 9
D1+_HDMI4
D1+ 2 9
4 D1+_HDMI2
3
D2- 3 8
D2- 3 8
3
2
D2_GND 4 7
D2-_HDMI4
D2_GND 4 7
2 D2-_HDMI2
1
D2+ 5 6
D2+_HDMI4
1
D2+ 5 6 D2+_HDMI2
IP4294CZ10-TBR
IP4294CZ10-TBR ESD_HDMI_IP4294 MHL_CD_SENSE
ESD_HDMI1_VARISTOR
VA4201 ESD_HDMI_IP4294 JK4201 ESD_HDMI C4200 R4222
VA4209
JK4200 VA4208 0.047uF 300K

5.6V
25V
OPT
ESD_HDMI1_CAP ESD_HDMI1_CAP
VA4200-*1 VA4201-*1
1uF 1uF
10V 10V
CEC
D4203-*1 D4204-*1 D4205-*1 D4206-*1
IP4283CZ10-TBA IP4283CZ10-TBA IP4283CZ10-TBA IP4283CZ10-TBA
R4202
100 TMDS_CH1-
1 10
NC_4 TMDS_CH1-
1 10
NC_4 TMDS_CH1-
1 10
NC_4 TMDS_CH1-
1 10
NC_4
HDMI_CEC CEC_REMOTE_S7
2 9 2 9 2 9 2 9
GND_1 GND_2 GND_1 GND_2 GND_1 GND_2 GND_1 GND_2

3 8 3 8 3 8 3 8

4 7 4 7 4 7 4 7

5 6 5 6 5 6 5 6
5V_HDMI_2 +5V_Normal 5V_HDMI_4 +5V_Normal ESD_HDMI_IP4283 ESD_HDMI_IP4283 ESD_HDMI_IP4283 ESD_HDMI_IP4283

+3.5V_ST
D4203-*2 D4204-*2 D4205-*2 D4206-*2

A1
A2
A1
A2
A1
A2
MMBD6100 MMBD6100 MMBD6100 RCLAMP0524PA RCLAMP0524PA RCLAMP0524PA RCLAMP0524PA

D4200 D4201 D4202 1 10 1 10 1 10 1 10
C
2 9 2 9 2 9 2 9
3 8 3 8 3 8 3 8
4 7 4 7 4 7 4 7
R4200 R4201
R4205 R4207
5 6 5 6 5 6 5 6
2.7K 2.7K 2.7K 2.7K
DDC_SDA_2 DDC_SDA_4 ESD_HDMI_SEMTECH ESD_HDMI_SEMTECH ESD_HDMI_SEMTECH ESD_HDMI_SEMTECH
DDC_SCL_2 DDC_SCL_4

HDMI_R2 42
Downloaded
IR/LED + Digital Eye + Control
+3.5V_ST
R4603 R4604
10K 10K
1% 1%
R4601
100 P4600 OPT
KEY1
OPT 12507WR-10L P4601
C4602 12507WR-08L
0.1uF
16V
R4602 1
100 1
KEY2
OPT
C4603 2
0.1uF 2
+3.5V_ST 16V
3
L4600 3
BLM18PG121SN1D
4
4
R4606
+3.5V_ST C4600 C4601 1.8K
0.1uF 1000pF LED_R/BUZZ 5
16V 50V 5
VA4600
LED_R_Zener
R4600 6
3.3K 6
IR 7
C4604 7
VA4601
100pF IR_Zener
50V 8
8
9 9
+3.3V_Normal
10
Digital Eye Digital Eye OPT 11

R4605 R4607 C4605
1K 1K 18pF
50V
R4608 100
SENSOR_SCL
Digital Eye
R4609 100
SENSOR_SDA
Digital Eye OPT
C4606
18pF
50V

THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. IR_EYE_SENSOR 46
Downloaded
NAND FLASH MEMORY +3.5V_ST PM MODEL OPTION
<CHIP Config>
IC102 (SPI_SDI, PM_LED, PWM_PM)
H27U1G8F2CTR-BC R177
LG-NonOS SB51_ExtSPI 3’b000 51boot from SPI 10K PM_MODEL_OPT_0
LG-OS HEMCU_ExtSPI 3’b001 MIPS boot from SPI LCD - HIGH : LCD
+3.3V_Normal +3.3V_Normal +3.5V_ST PM_MODEL_OPT_0
NC_1 NC_29 R176 - LOW :: PDP
1 NAND_FLASH_1G_HYNIX
48 10K
PDP PM_MODEL_OPT_1
NC_2 NC_28 M1A_256M
2 EAN35669103 47 M1A_128M
- Not Use (Ready) IC101
NC_3 NC_27 PCM_A[0-7] IC101-*1
4.7K
LGE2132(M1A_256M)
4.7K
2.7K
3 46 LGE2131(M1A_128M)
22
NC_4 NC_26 I2C
OPT
OPT
4 45 AR101 +3.3V_Normal
NC_5 I/O7 PCM_A[7]
R115
R117
R165
5 44 U19 D5
RXA4+ LVA4P/TTL_B[0]/HCONV/GPIO170 U19 D5
NC_6 I/O6 PCM_A[6] SAR0/GPIO35 KEY1 LVA4P/TTL_B[0]/HCONV/GPIO170 SAR0/GPIO35
6 43 R140 R141 R144 R145 T20 F8 T20 F8
AR103 R107 R109 1K 1K 2.2K 2.2K RXA4- LVA4M/TTL_B[1]/E_O/GPIO171 SAR1/GPIO36 KEY2
22 T21 E7 LVA4M/TTL_B[1]/E_O/GPIO171 SAR1/GPIO36
1K 3.9K R/B I/O5 PCM_A[5] LED_R/BUZZ RXA3+ T21 E7
7 42 I2C_SDA LVA3P/TTL_B[2]/FB/GPIO172 SAR2/GPIO37 PM_MODEL_OPT_0 LVA3P/TTL_B[2]/FB/GPIO172 SAR2/GPIO37
T19 E6 T19 E6
RE I/O4 PCM_A[4] PM_LED I2C_SCL RXA3- LVA3M/TTL_B[3]/OPT_P/GPIO173 SAR3/GPIO38 PANEL_CTL LVA3M/TTL_B[3]/OPT_P/GPIO173
/F_RB R21 D6 SAR3/GPIO38
8 41 RXACK+ R21 D6
AMP_SDA LVACKP/TTL_B[4]/MCLK/GPIO174 SAR4/GPIO39 SCART1_MUTE LVACKP/TTL_B[4]/MCLK/GPIO174 SAR4/GPIO39
/PF_OE CE NC_25 SPI_SDI R20 R20
9 40 AMP_SCL RXACK- LVACKM/TTL_B[5]/GCLK/GPIO175
/PF_CE0 R19 W10 LVACKM/TTL_B[5]/GCLK/GPIO175
4.7K
4.7K
2.7K
RXA2+ R19 W10

NC_7 NC_24 LVA2P/TTL_B[6]/GST/GPIO176 GPIO_PM[13]/GPIO20 MHL_CD_SENSE LVA2P/TTL_B[6]/GST/GPIO176 GPIO_PM[13]/GPIO20
10 39 C102 P20 Y10 P20 Y10
R108 10uF RXA2- LVA2M/TTL_B[7]/POL/GPIO177 GPIO_PM[14]/GPIO21 /VBUS_EN
OPT
1K P3 LVA2M/TTL_B[7]/POL/GPIO177 GPIO_PM[14]/GPIO21
OPT
NC_8
11 38
NC_23 10V DIMMING PM_LED/GPIO4 PM_LED
P3
C101 P19 Y3 PM_LED/GPIO4
R116
R118
R121
RXA1+ P19 Y3
0.1uF VCC_1 VCC_2 LVA1P/TTL_G[0]/EPI0+/GPIO178 GPIO_PM[0]/GPIO7 POWER_DET LVA1P/TTL_G[0]/EPI0+/GPIO178 GPIO_PM[0]/GPIO7
12 37 N20 Y5 N20 Y5
RXA1- LVA1M/TTL_G[1]/EPI0-/GPIO179 PM_SPI_SCZ2/GPIO_PM[10]/GPIO17 AMP_MUTE
C103 N21 W11 LVA1M/TTL_G[1]/EPI0-/GPIO179 PM_SPI_SCZ2/GPIO_PM[10]/GPIO17
VSS_1 VSS_2 R157 100 RXA0+ N21 W11
13 36 0.1uF PWM_DIM PWM2 LVA0P/TTL_G[2]/EPI1+/GPIO180 GPIO_PM[15]/GPIO22 INV_CTL LVA0P/TTL_G[2]/EPI1+/GPIO180 GPIO_PM[15]/GPIO22
R156 10K N19 D3 N19 D3
NC_9 NC_22 PWM0 RXA0- LVA0M/TTL_G[3]/EPI1-/GPIO181 GPIO_PM[4]/GPIO11 POWER_ON/OFF_1
M21 AA3 LVA0M/TTL_G[3]/EPI1-/GPIO181 GPIO_PM[4]/GPIO11
+3.3V_Normal 14 35 R103 10K RXB4+ M21 AA3
PWM3 LVB4P/TTL_G[4]/EPI2+/GPIO182 GPIO_PM[7]/GPIO14 RL_ON LVB4P/TTL_G[4]/EPI2+/GPIO182 GPIO_PM[7]/GPIO14
NC_10 NC_21 M20 W5 M20 W5
R105 15 34 RXB4- LVB4M/TTL_G[5]/EPI2-/GPIO183 GPIO_PM[8]/GPIO15 /FLASH_WP
NVRAM_RHOM M19 D4 LVB4M/TTL_G[5]/EPI2-/GPIO183 GPIO_PM[8]/GPIO15
1K RXB3+ M19 D4
OPT CLE NC_20 LVB3P/TTL_G[6]/EPI3+/GPIO184 PWM_PM/GPIO200 LED_R/BUZZ LVB3P/TTL_G[6]/EPI3+/GPIO184 PWM_PM/GPIO200
16 33 IC104 L20 L15 L20 L15
AR104
22
AR102 BR24G256FJ-3
RXB3- LVB3M/TTL_G[7]/EPI3-/GPIO185 PM_UART_TX/GPIO_PM[1]/GPIO8
Y11
PM_TXD LVB3M/TTL_G[7]/EPI3-/GPIO185 PM_UART_TX/GPIO_PM[1]/GPIO8
ALE I/O3 PCM_A[3] Y11
17 32 PM_UART_RX/GPIO_PM[5]/GPIO12 PM_RXD PM_UART_RX/GPIO_PM[5]/GPIO12
/PF_CE1 +3.3V_Normal EEPROM L19 L19
WE I/O2 PCM_A[2] RXBCK+ LVBCKP/TTL_R[0]/EPI4+/GPIO186
PF_ALE K20 LVBCKP/TTL_R[0]/EPI4+/GPIO186
18 31 A0 VCC RXBCK- K20
LVBCKM/TTL_R[1]/EPI4-/GPIO187 LVBCKM/TTL_R[1]/EPI4-/GPIO187
/PF_WE WP I/O1 PCM_A[1] 1 8 K21 K21
19 30 C105 RXB2+ LVB2P/TTL_R[2]/EPI5+/GPIO188
/PF_WP K19 LVB2P/TTL_R[2]/EPI5+/GPIO188
0.1uF RXB2- K19
R102 R106 NC_11 I/O0 PCM_A[0] LVB2M/TTL_R[3]/EPI5-/GPIO189 LVB2M/TTL_R[3]/EPI5-/GPIO189
3.3K 1K 20 29 A1 WP J21 J21
2 7 RXB1+ LVB1P/TTL_R[4]/EPI6+/GPIO190
J20 LVB1P/TTL_R[4]/EPI6+/GPIO190
NC_12 NC_19 22 RXB1- LVB1M/TTL_R[5]/EPI6-/GPIO191 J20
21 28 J19 LVB1M/TTL_R[5]/EPI6-/GPIO191
A2 A0’h SCL RXB0+ LVB0P/TTL_R[6]/EPI7+/GPIO192 J19
NC_13 NC_18 3 6 R111 22 H20 LVB0P/TTL_R[6]/EPI7+/GPIO192
22 27 I2C_SCL H20
RXB0- LVB0M/TTL_R[7]/EPI7-/GPIO193 LVB0M/TTL_R[7]/EPI7-/GPIO193
NC_14 NC_17
23 26 GND SDA
4 5 R112 22
NC_15 NC_16 I2C_SDA
24 25 C104 C106
8pF 8pF
OPT OPT
EAN62389502
NAND_FLASH_2G_HYNIX NAND_FLASH_1G_TOSHIBA
EAN60708702 EAN61508001 NVRAM_ATMEL
IC102-*1 IC102-*2 IC104-*1
H27U2G8F2CTR TC58NVG0S3ETA0BBBH AT24C256C-SSHL-T M1A_256M M1A_128M
IC101 IC101-*1
A0 VCC LGE2132(M1A_256M) from CI SLOT LGE2131(M1A_128M)
NC_1 NC_29 NC_1 NC_29 1 8
1 48 1 48
NC_2 NC_28 NC_2 NC_28 A1 WP CI_TS_CLK
2 47 2 47 2 7 CI_TS_DATA[0-7]
NC_3 NC_27 NC_3 NC_27 Y1 V10 Y1 V10
3 46 3 46 GPIO78 TS0CLK/GPIO92 CI_TS_DATA[0] CI_TS_SYNC GPIO78 TS0CLK/GPIO92
A2 SCL W4 T14 W4 T14
3 6 CI_TS_VAL
NC_4 NC_26 NC_4 NC_26 5V_DET_HDMI_4 GPIO79 TS0DATA[0]/GPIO82 CI_TS_DATA[1] GPIO79 TS0DATA[0]/GPIO82
4 45 4 45 T13 T13
GND SDA
TS0DATA[1]/GPIO83 CI_TS_DATA[2] TS0DATA[1]/GPIO83
NC_5 I/O7 NC_5 I/O8 4 5 R184 22 K17 U13 K17 U13
5 44 5 44 I2C_SCL I2C_SCKM3/I2C_DDCR_CK/GPIO77 TS0DATA[2]/GPIO84 CI_TS_DATA[3] I2C_SCKM3/I2C_DDCR_CK/GPIO77 TS0DATA[2]/GPIO84
R183 22 J15 V15 J15 V15
NC_6 I/O6 NC_6 I/O7 I2C_SDA I2C_SDAM3/I2C_DDCR_DA/GPIO76 TS0DATA[3]/GPIO85 CI_TS_DATA[4] I2C_SDAM3/I2C_DDCR_DA/GPIO76 TS0DATA[3]/GPIO85
6 43 6 43 U8 U12 U8 U12
URSA/VCOM_SDA SDAM2/GPIO55 TS0DATA[4]/GPIO86 CI_TS_DATA[5] SDAM2/GPIO55 TS0DATA[4]/GPIO86
R/B I/O5 RY/BY I/O6 EAN61133501 T7 V13 T7 V13
7 42 7 42 URSA/VCOM_SCL SCKM2/GPIO56 TS0DATA[5]/GPIO87 CI_TS_DATA[6] SCKM2/GPIO56 TS0DATA[5]/GPIO87
U7 U14 U7 U14
RE I/O4 RE I/O5 SENSOR_SCL SCKM0/GPIO58 TS0DATA[6]/GPIO88 CI_TS_DATA[7] SCKM0/GPIO58 TS0DATA[6]/GPIO88
8 41 8 41 V7 T11 Internal demod out V7 T11
SENSOR_SDA SDAM0/GPIO59 TS0DATA[7]/GPIO89 SDAM0/GPIO59 TS0DATA[7]/GPIO89
CE NC_25 CE NC_25 T2_OR_CHINA F6 T12 F6 T12
9 40 9 40 R113 22 AMP_SCL I2S_IN_BCK/GPIO159 TS0SYNC/GPIO91 FE_TS_CLK I2S_IN_BCK/GPIO159 TS0SYNC/GPIO91
DEMOD_SCL G6 V12 G6 V12
R114 22 AMP_SDA I2S_IN_SD/GPIO160 TS0VALID/GPIO90 FE_TS_DATA[0-7] I2S_IN_SD/GPIO160 TS0VALID/GPIO90
NC_7 NC_24 NC_7 NC_24 AA4 Y14 AA4 Y14
10 39 10 39 DEMOD_SDA
T2_OR_CHINA TU_SCL I2C_SCKM1/GPIO80 TS1CLK/GPIO103 FE_TS_DATA[0] FE_TS_SYNC I2C_SCKM1/GPIO80 TS1CLK/GPIO103
NC_8 NC_23 NC_8 NC_23 Y4 Y16 Y4 Y16
11 38 11 38 TU_SDA I2C_SDAM1/GPIO81 TS1DATA[0]/GPIO93 FE_TS_DATA[1] FE_TS_VAL_ERR I2C_SDAM1/GPIO81 TS1DATA[0]/GPIO93
AA15 AA15
VCC_1 VCC_2 VCC_1 VCC_2 TS1DATA[1]/GPIO94 FE_TS_DATA[2] TS1DATA[1]/GPIO94
12 37 12 37 J6 Y13 J6 Y13
AV_CVBS_DET ET_TXD[0]/GPIO62 TS1DATA[2]/GPIO95 FE_TS_DATA[3] ET_TXD[0]/GPIO62 TS1DATA[2]/GPIO95
VSS_1 VSS_2 VSS_1 VSS_2 K6 AA16 K6 AA16
13 36 13 36 AV2_CVBS_DET EXT_TX_CLK/GPIO64 TS1DATA[3]/GPIO96 FE_TS_DATA[4] FE_TS_DATA[0] EXT_TX_CLK/GPIO64 TS1DATA[3]/GPIO96
W12 W12
TS1DATA[4]/GPIO97 FE_TS_DATA[0] TS1DATA[4]/GPIO97
NC_9 NC_22 NC_9 NC_22 G7 AA13 FE_TS_DATA[5] G7 AA13
14 35 14 35
COMP2_DET I2S_IN_WS/GPIO158 TS1DATA[5]/GPIO98 FE_TS_DATA[6] I2S_IN_WS/GPIO158 TS1DATA[5]/GPIO98
NC_10 NC_21 NC_10 NC_21 W14 W14
15 34 15 34 TS1DATA[6]/GPIO99 FE_TS_DATA[7] TS1DATA[6]/GPIO99
J4 W13 J4 W13
CLE NC_20 CLE NC_20 DEMOD_RESET ET_COL/GPIO60 TS1DATA[7]/GPIO100 ET_COL/GPIO60 TS1DATA[7]/GPIO100
16 33 16 33 J5 Y15 J5 Y15
MODEL_OPT_0 ET_TXD[1]/GPIO61 TS1SYNC/GPIO102 ET_TXD[1]/GPIO61 TS1SYNC/GPIO102
ALE I/O3 ALE I/O4 W15 W15
17 32 17 32 TS1VALID/GPIO101 TS1VALID/GPIO101
H19 H19
WE I/O2 WE I/O3 MODEL_OPT_1 LCK/GPIO194 LCK/GPIO194
18 31 18 31 G20 B3 R189 33 G20 B3
MODEL_OPT_2 LDE/GPIO195 PM_SPI_SCZ1/GPIO_PM[6]/GPIO13 /SPI_CS LDE/GPIO195 PM_SPI_SCZ1/GPIO_PM[6]/GPIO13
WP I/O1 WP I/O2 G19 A3 R188 33 G19 A3
19 30 19 30 /MHL_OCP_DET LHSYNC/GPIO196 PM_SPI_SCK/GPIO1 SPI_SCK LHSYNC/GPIO196 PM_SPI_SCK/GPIO1
G21 A4 G21 A4
NC_11 I/O0 NC_11 I/O1 FRC_RESET LVSYNC/GPIO197 PM_SPI_SCZ0/GPIO0 SIDE_HP_MUTE LVSYNC/GPIO197 PM_SPI_SCZ0/GPIO0
20 29 20 29 33 R182 C3 C3
PM_SPI_SDI/GPIO2 SPI_SDI PM_SPI_SDI/GPIO2
NC_12 NC_19 NC_12 NC_19 J17 A2 R190 33 J17 A2
21 28 21 28 HP_DET UART2_RX/GPIO69 PM_SPI_SDO/GPIO3 SPI_SDO UART2_RX/GPIO69 PM_SPI_SDO/GPIO3
J16 J16
NC_13 NC_18 NC_13 NC_18 SC1/COMP1_DET UART2_TX/GPIO70 UART2_TX/GPIO70
22 27 22 27 E8 B1 E8 B1
MHL_OCP_EN UART3_TX/GPIO52 RP EPHY_RP UART3_TX/GPIO52 RP
NC_14 NC_17 NC_14 NC_17 D7 C2 D7 C2
23 26 23 26 AMP_RESET UART3_RX/GPIO53 TN EPHY_TN UART3_RX/GPIO53 TN
U6 C1 U6 C1
NC_15 NC_16 NC_15 NC_16 MODEL_OPT_4 GPIO46[CTS] TP EPHY_TP GPIO46[CTS] TP
24 25 24 25 V6 B2 V6 B2
RF_SWITCH_CTL GPIO47[RTS] RN EPHY_RN GPIO47[RTS] RN
33 R181 K15 K15
/CI_CD1 UART1_TX/GPIO48 UART1_TX/GPIO48
L16 D2 L16 D2
/CI_CD2 UART1_RX/GPIO49 SPDIF_IN/GPIO161 5V_DET_HDMI_2 UART1_RX/GPIO49 SPDIF_IN/GPIO161
D1 R192 100 D1
+3.3V_Normal SPDIF_OUT/GPIO162 SPDIF_OUT SPDIF_OUT/GPIO162
NAND_FLASH_2G_TOSHIBA NAND_FLASH_1G_SS H5 SPDIF_OPTIC H5
USB1_CTL ET_TX_EN/GPIO63 ET_TX_EN/GPIO63
EAN60991001 EAN61857001 R180 K5 D8 K5 D8
IC102-*3 IC102-*4 10K MODEL_OPT_5 ET_RXD[0]/GPIO65 HWRESET SOC_RESET ET_RXD[0]/GPIO65 HWRESET
K4 E5 K4 E5
TC58NVG1S3ETA00 K9F1G08U0D-SCB0 R197 0 MODEL_OPT_6 ET_MDC/GPIO66 IRIN/GPIO5 IR ET_MDC/GPIO66 IRIN/GPIO5
CI_DET H6 G4 H6 G4
R178 22 USB1_OCD ET_MDIO/GPIO67 DDCA_CK/UART0_RX RGB_DDC_SCL ET_MDIO/GPIO67 DDCA_CK/UART0_RX
/PCM_CD L5 G5 L5 G5
PCM_A[0-14] ET_RXD[1]/GPIO68 DDCA_DA/UART0_TX RGB_DDC_SDA ET_RXD[1]/GPIO68 DDCA_DA/UART0_TX
NC_1 NC_29 NC_1 NC_29
1 48 1 48 PCM_A[0] U17 J18 U17 J18
2 47 2 47 R18 K18 R18 K18
PCM_A[2] PCMADR[1]/NF_AD[1]/GPIO129 PWM1/GPIO72 PWM1 PCMADR[1]/NF_AD[1]/GPIO129 PWM1/GPIO72
NC_3 NC_27 NC_3 NC_27 V17 K16 V17 K16
3 46 3 46 PCM_A[3] PCMADR[2]/NF_AD[2]/GPIO127 PWM2/GPIO73 PWM2 PCMADR[2]/NF_AD[2]/GPIO127 PWM2/GPIO73
R16 L18 R16 L18
4 45 4 45 U16 L17 U16 L17
PCM_A[5] PCMADR[4]/NF_AD[4]/GPIO104 PWM4/GPIO75 PCM_5V_CTL PCMADR[4]/NF_AD[4]/GPIO104 PWM4/GPIO75
NC_5 I/O8 NC_5 I/O7 T17 T17
5 44 5 44 PCM_A[6] PCMADR[5]/NF_AD[5]/GPIO106 PCMADR[5]/NF_AD[5]/GPIO106
W18 T8 +3.3V_Normal W18 T8
NC_6 I/O7 NC_6 I/O6 PCM_A[7] PCMADR[6]/NF_AD[6]/GPIO107 NF_ALE/GPIO146 PF_ALE PCMADR[6]/NF_AD[6]/GPIO107 NF_ALE/GPIO146
6 43 6 43 U20 T9 U20 T9
PCM_A[8] PCMADR[7]/NF_AD[7]/GPIO108 NF_CEZ/GPIO142 /PF_CE0 PCMADR[7]/NF_AD[7]/GPIO108 NF_CEZ/GPIO142
RY/BY I/O6 R/B I/O5 Y19 U9 Y19 U9
7 42 7 42 PCM_A[9] PCMADR[8]/GPIO113 NF_CLE/GPIO141 /PF_CE1 L101 PCMADR[8]/GPIO113 NF_CLE/GPIO141
AA19 U11 BLM18PG121SN1D AA19 U11
RE I/O5 RE I/O4 PCM_A[10] PCMADR[9]/GPIO115 NF_RBZ/GPIO147 /F_RB PCMADR[9]/GPIO115 NF_RBZ/GPIO147
8 41 8 41 AA20 V9 AA20 V9
PCM_A[11] PCMADR[10]/GPIO119 NF_REZ/GPIO144 /PF_OE PCMADR[10]/GPIO119 NF_REZ/GPIO144
CE NC_25 CE NC_25 W21 U10 R193 C119 W21 U10
9 40 9 40 PCM_A[12] PCMADR[11]/GPIO117 NF_WEZ/GPIO145 /PF_WE 10K 0.1uF PCMADR[11]/GPIO117 NF_WEZ/GPIO145
V20 T10 V20 T10
NC_7 NC_24 NC_7 NC_24 PCM_A[13] PCMADR[12]/GPIO109 NF_WPZ/GPIO199 /PF_WP R196 PCMADR[12]/GPIO109 NF_WPZ/GPIO199
10 39 10 39 Y17 0 Y17
PCM_A[14] PCMADR[13]/GPIO112 IF_AGC_MAIN PCMADR[13]/GPIO112
NC_8 NC_23 NC_8 NC_23 V18 W2 C120 V18 W2
11 38 11 38 PCMADR[14]/GPIO111 IF_AGC CHINA 0.047uF PCMADR[14]/GPIO111 IF_AGC
V19 W1 C115 0.1uF R198 CHINA47 V19 W1
VCC_1 VCC_2 VCC_1 VCC_2 PCM_D[0-7] /PCM_CD PCMCD_N/GPIO135 SIFM 25V PCMCD_N/GPIO135 SIFM
12 37 12 37 W19 W3 C116 0.1uF R199 47 W19 W3
/PCM_CE PCMCE_N/GPIO120 SIFP C123 PCMCE_N/GPIO120 SIFP
VSS_1 VSS_2 VSS_1 VSS_2 PCM_D[0] U18 V2 CHINA CHINA 1000pF U18 V2
13 36 13 36 PCMDATA[0]/GPIO131 IM PCMDATA[0]/GPIO131 IM
PCM_D[1] V16 V1 ANALOG SIF OPT V16 V1
NC_9 NC_22 NC_9 NC_22 PCMDATA[1]/GPIO132 IP PCMDATA[1]/GPIO132 IP
14 35 14 35 PCM_D[2] W17 Close to MSTAR TU_SIF W17
PCMDATA[2]/GPIO133 PCMDATA[2]/GPIO133
NC_10 NC_21 NC_10 NC_21 PCM_D[3] Y20 AA2 R194 0 Y20 AA2
15 34 15 34 PCMDATA[3]/GPIO125 XIN IF_N_MSTAR PCMDATA[3]/GPIO125 XIN
PCM_D[4] R15 Y2 OPT R15 Y2
CLE NC_20 CLE NC_20 PCMDATA[4]/GPIO124 XOUT C117 C121 PCMDATA[4]/GPIO124 XOUT
16 33 16 33 PCM_D[5] AA18 0.1uF 100pF DTV_IF AA18
PCMDATA[5]/GPIO123 R195 0 PCMDATA[5]/GPIO123
ALE I/O4 ALE I/O3 PCM_D[6] T15 IF_P_MSTAR T15
17 32 17 32 PCMDATA[6]/GPIO122 C118 C122 C124 PCMDATA[6]/GPIO122
PCM_D[7] Y21 0.1uF 33pF 33pF Y21
WE I/O3 WE I/O2 PCMDATA[7]/GPIO121 TU_NON_ATSC TU_NON_ATSC PCMDATA[7]/GPIO121
18 31 18 31 W20 W20
/PCM_IORD PCMIORD_N/GPIO116 PCMIORD_N/GPIO116
WP I/O2 WP I/O1 V21 Close to MSTAR V21
19 30 19 30 /PCM_IOWR PCMIOWR_N/GPIO114 PCMIOWR_N/GPIO114
Y18 Y18
NC_11 I/O1 NC_11 I/O0 /PCM_IRQA PCMIRQA_N/GPIO110 XTAL_LOAD_22pF PCMIRQA_N/GPIO110
20 29 20 29 T16 T16
/PCM_OE PCMOE_N/GPIO118 PCMOE_N/GPIO118
R17 R17
R187
NC_12 NC_19 NC_12 NC_19

/PCM_REG
X101 C113 22pF
21 28 21 28 PCMREG_N/GPIO128 PCMREG_N/GPIO128
1M
T18 24MHz C114 22pF T18

NC_13 NC_18 NC_13 NC_18 PCM_RST PCM_RESET/GPIO134 PCM_RESET/GPIO134
22 27 22 27 W16 W16
/PCM_WAIT PCMWAIT_N/GPIO105 XTAL_LOAD_22pF PCMWAIT_N/GPIO105
NC_14 NC_17 NC_14 NC_17 U15 U15
23 26 23 26 /PCM_WE PCMWE_N/GPIO198 PCMWE_N/GPIO198
NC_15 NC_16 NC_15 NC_16 XTAL_LOAD_30pF XTAL_LOAD_27pF
24 25 24 25 C113-*1 30pF C113-*2 27pF
XTAL_LOAD_30pF XTAL_LOAD_27pF
C114-*1 30pF C114-*2 27pF

Downloaded
MODEL OPTION +3.3V_Normal
SOC_RESET +3.5V_ST
STby 3.5V Normal Power 3.3V DDR3 1.5V VDDC 1.05V +1.10V_VDDC
+1.10V_VDDC
MO_DVB_T2/C/S2
MO_DUALSTREAM
MO_S/W_EU/AJ
SWITCH_POSTEC
DDR_EXT:256
DDR_EXT:128
1K
1K
1K
1K
1K
1K
1K
L206
1K
MO_S/W_AJ
SW200-*1 BLM18PG121SN1D AVDD_NODIE +1.5V_DDR VDDC : 2026mA

MO_M120
TMSV153BRA +3.3V_Normal VDD33

MO_HD
+1.10V_VDDC
2
C289 C286 C252 +1.10V_VDDC

POWER_DET_RESET +3.5V_ST SWITCH_NAMAE 10uF 0.1uF 0.1uF AVDD_DDR0:55mA
SW200 C296 C210 C279
L204 10uF 0.1uF 0.1uF
R291
R222
R221
R206
R208
R211
R226
R290
JTP-1127WEM
0.1uF
0.1uF
0.1uF
BLM18PG121SN1D 10V
2
10uF
0.1uF
1
10V
1uF
OPT
0.1uF
0.1uF
0.1uF
0.1uF
10V
10V
0.1uF
1uF
1uF
R201 OPT 100 R266 L207
IF_AGC_SEL MODEL_OPT_0 470 SWITCH
10V
10V
R202 OPT 100 R205 BLM18PG121SN1D AVDD_DMPLL

MODEL_OPT_1 100
C275
C248
C207
C254
1
C278
C228
C266
R203 OPT 100
10uF
10uF
OPT C288 C205
C277
C280
C283
MODEL_OPT_2
C284
10uF
C204
10uF
C202 C200 10uF 0.1uF

C209
C235
C245
R204 OPT 100

C255
C259
AUD_LRCH 4.7uF 4.7uF R217

R225 OPT 100 10V 10V 0
MODEL_OPT_4
R228 OPT 100 L208 AVDD_DDR1:55mA
MODEL_OPT_5 SOC_RESET BLM18PG121SN1D AVDD_AU33
R230 OPT 100
MODEL_OPT_6
OPT 100
DDR_EXT:128 or NON
DDR_EXT:256 or NON
R229 AUD_LRCK R200 C201 C240 C287 C241

MO_DUALSTREAM_NON
470K 0.1uF 0.1uF 10uF 0.1uF

MO_S/W_NON_AJ
1K
MO_S/W_TW/CN
1K
1K
1K
1K
1K
1K
1K
MO_DVB_T/C
MO_M120_NON
MO_FHD
R212
R294
R293
R224
R223
R207
R209
R227
MODEL OPTION
PIN NAME PIN NO. LOW HIGH
MODEL_OPT_0 J5 MO_FHD MO_HD
MODEL_OPT_1 H19 MO_S/W_NON_AJ MO_S/W_AJ
MODEL_OPT_2 G20 MO_DVB_T/C MO_DVB_T2/C/S2

AUD_LRCH G19 MO_M120_NON MO_M120
MODEL_OPT_4 U6 DDR_EXT:256 or NON DDR_EXT : 128
MODEL_OPT_5 K5 MO_S/W_TW/CN MO_S/W_EU/AJ
M1A_256M M1A_128M
MODEL_OPT_6 K4 DDR_EXT:128 or NON DDR_EXT : 256 IC101 IC101-*1
LGE2132(M1A_256M) LGE2131(M1A_128M)
AUD_LRCK L5 MO_DUALSTREAM_NON MO_DUALSTREAM
* Dual Stream is only Korea 3D spec

R4 U3 R4 U3
AVDD_AU33 AVDD_AU33 AUVRM AUVRM AVDD_AU33 AUVRM
L11 A6 L11 A6
AVDD_DDR0_CLK GND_1 AVDD_DDR0_CLK GND_1
Memory OPTION L13
M11
AVDD_DDR1_CLK
AVDD_DDR0_CMD
GND_2
GND_3
A13
A15
L13
M11
AVDD_DDR1_CLK
AVDD_DDR0_CMD
GND_2
GND_3
A13
A15
Memory Auto K13 A18 K13 A18
MODEL_OPT_4 MODEL_OPT_6 C5
AVDD_DDR1_CMD GND_4
B12 C5
AVDD_DDR1_CMD GND_4
B12
INT+EXT Det +1.5V_DDR
K12 B14 K12 B14
128M Only 0 0 0 L12
AVDD_DDR0_D_2 GND_6
B16 L12
AVDD_DDR0_D_2 GND_6
B16
C6 B17 C6 B17
256M Only 1 0 0 K14
AVDD_DDR1_D_1 GND_8
B19 K14
AVDD_DDR1_D_1 GND_8
B19
L14 B20 L14 B20
128M+128M 0 1 0 B5
C9 B5
C9
AVDD_DRAM_1 GND_11 AVDD_DRAM_1 GND_11
B6 C10 B6 C10
128M+256M 0 0 1 R8
AVDD_DRAM_2 GND_12
C21 R8
AVDD_DRAM_2 GND_12
C21
AVDD_NODIE AVDD_DVI_USB_MPLL_1 GND_13 AVDD_DVI_USB_MPLL_1 GND_13
R9 D9 R9 D9
256M+256M 1 0 1 L7
E20 L7
E20
VDD33 AVDD_MOD_1 GND_15 AVDD_MOD_1 GND_15
L8 F9 L8 F9
AVDD_MOD_2 GND_16 AVDD_MOD_2 GND_16
P8 F11 P8 F11
AVDD_NODIE AVDD_NODIE GND_17 AVDD_NODIE GND_17
K9 F13 K9 F13
VDD33 AVDD_PLL GND_18 AVDD_PLL GND_18
Country Option AVDD_DMPLL
+1.10V_VDDC
R5
P11
AVDD3P3_DMPLL
AVDDL_MOD
GND_19
GND_20
F15
F17
R5
P11
AVDD3P3_DMPLL
AVDDL_MOD
GND_19
GND_20
F15
F17
C7 F19 C7 F19
MODEL_OPT_1 MODEL_OPT_5 +1.10V_VDDC DVDD_DDR_1 GND_21 DVDD_DDR_1 GND_21
M13 F21 M13 F21
1uFC260 DVDD_DDR_2 GND_22 DVDD_DDR_2 GND_22
R6 G8 R6 G8
DVDD_NODIE GND_23 DVDD_NODIE GND_23
TW 0 0 A7 G9 A7 G9
M12 G10 M12 G10
B7 G11 B7 G11
EU 0 1 DVDD_RX_2_1 GND_26 DVDD_RX_2_1 GND_26
M14 G12 M14 G12
N11 G13 N11 G13
+1.10V_VDDC VDDC_1 GND_28 VDDC_1 GND_28
CN 1 0 N12 G14 N12 G14
N13 G15 N13 G15
N14 G16 N14 G16
AJ 1 1 VDDC_4 GND_31 VDDC_4 GND_31
N15 G17 N15 G17
P12 G18 P12 G18
P13 H7 P13 H7
P14 H8 P14 H8
L9 H9 L9 H9
VDD33 VDDP GND_36 VDDP GND_36
H10 H10
GND_37 GND_37
AA10 H11 AA10 H11
AVDD5V_MHL AVDD5V_MHL GND_38 AVDD5V_MHL GND_38
H12 H12
GND_39 GND_39
H13 H13
GND_40 GND_40
H14 H14
GND_41 GND_41
H15 H15
GND_42 GND_42
H16 H16
GND_43 GND_43
H17 H17
GND_44 GND_44
M1A_256M M1A_128M H18 H18
GND_45 GND_45
IC101 IC101-*1 J7 J7
GND_46 GND_46
LGE2132(M1A_256M) LGE2131(M1A_128M) J8 J8
GND_47 GND_47
J9 J9
GND_48 GND_48
J10 J10
GND_49 GND_49
HDMI1_ARC HDMI1_ARC J11 J11
M4 T6 M4 T6 GND_50 GND_50
DTV/MNT_VOUT J12 J12
HDMI
HDMI_ARC ARC0 CVBSOUT1 ARC0 CVBSOUT1

C212 1uF R231 0 W7 V5 0.047uF C236 33 R244 W7 V5 GND_51 GND_51
D0-_HDMI4 R214 10 RXC0N CVBS0 TU_CVBS RXC0N CVBS0 J13 J13
Y8 U5 0.047uF C237 33 R245 Y8 U5 GND_52 GND_52
D0+_HDMI4 R215 10 RXC0P CVBS1 SC1/AV2_CVBS_IN RXC0P CVBS1 J14 J14
W8 T5 0.047uF C238 33 R246 +3.3V_Normal W8 T5 GND_53 GND_53
D1-_HDMI4 RXC1N CVBS2 COMP2_Y+/AV_CVBS_IN RXC1N CVBS2 K8 K8
Y9 V4 0.047uF C239 68 R247 C242 Close Y9 V4 GND_54 GND_54
D1+_HDMI4 RXC1P VCOM 1000pF
to MSTAR RXC1P VCOM K10 K10
AA9 R213 R210 I2S_I/F AA9 GND_55 GND_55
D2-_HDMI4 RXC2N 50V 10K 10K RXC2N K11 K11
W9 E4 OPT OPT OPT W9 E4 GND_56 GND_56
D2+_HDMI4 RXC2P I2S_OUT_BCK/GPIO165 AUD_SCK RXC2P I2S_OUT_BCK/GPIO165 L10 L10
AA7 F4 AA7 F4 GND_57 GND_57
CK-_HDMI4 RXCCKN I2S_OUT_MCK/GPIO163 R295 0 AUD_MASTER_CLK RXCCKN I2S_OUT_MCK/GPIO163 M5 M5
Y7 F7 Y7 F7 GND_58 GND_58
CK+_HDMI4 RXCCKP I2S_OUT_SD/GPIO166 AUD_LRCH RXCCKP I2S_OUT_SD/GPIO166 M7 M7
N2 F5 N2 F5 GND_59 GND_59
CEC_REMOTE_S7 CEC/GPIO6 I2S_OUT_WS/GPIO164 AUD_LRCK CEC/GPIO6 I2S_OUT_WS/GPIO164 M8 M8
E3 R216 R218 E3 GND_60 GND_60
DDC_SCL_2 DDCDA_CK/GPIO27 10K 10K DDCDA_CK/GPIO27 M9 M9
E2 C4 OPT OPT C208 E2 C4 GND_61 GND_61
DDC_SDA_2 DDCDA_DA/GPIO28 USB0_DM DDCDA_DA/GPIO28 USB0_DM M10 M10
W6 Y12 15pF W6 Y12 GND_62 GND_62
DDC_SCL_4 DDCDC_CK/GPIO31 USB1_DM SIDE_USB1_DM 50V DDCDC_CK/GPIO31 USB1_DM N4 N4
AA6 B4 OPT AA6 B4 GND_63 GND_63
DDC_SDA_4 DDCDC_DA/GPIO32 USB0_DP SIDE USB DDCDC_DA/GPIO32 USB0_DP N5 N5
L4 AA12 L4 AA12 GND_64 GND_64
HPD2 HOTPLUGA/GPIO23 USB1_DP SIDE_USB1_DP HOTPLUGA/GPIO23 USB1_DP N6 N6
Y6 Y6 GND_65 GND_65
HPD4 HOTPLUGC/GPIO25 HOTPLUGC/GPIO25 N7 N7
F1 J2 F1 J2 GND_66 GND_66
D0-_HDMI2 RXA0N BIN0M C221 0.047uF R232 68 RXA0N BIN0M N8 N8
D0+_HDMI2 RXA0P BIN0P C222 0.047uF R233 33 SC1_B+/COMP1_Pb+ RXA0P BIN0P N9 N9
G1 K3 G1 K3 GND_68 GND_68
D1-_HDMI2 RXA1N GIN0M C223 0.047uF R234 68 RXA1N GIN0M N10 N10
D1+_HDMI2 RXA1P GIN0P C224 0.047uF R235 33 SC1_G+/COMP1_Y+ RXA1P GIN0P P4 P4
D2-_HDMI2 RXA2N RIN0M C225 0.047uF R236 68 RXA2N RIN0M P5 P5
D2+_HDMI2 RXA2P RIN0P C226 0.047uF R237 33 SC1_R+/COMP1_Pr+ RXA2P RIN0P P6 P6
F3 M6 F3 M6 GND_72 GND_72
CK-_HDMI2 RXACKN HSYNC0 SC1_ID RXACKN HSYNC0 P7 P7
F2 L6 F2 L6 GND_73 GND_73
CK+_HDMI2 RXACKP VSYNC0 SC1_FB RXACKP VSYNC0 P9 P9
GND_74 GND_74
P10 P10
H/P OUT U4 L2 U4 L2 GND_75 GND_75
HP_LOUT EAR_OUTL BIN1M C227 0.047uF R238 68 EAR_OUTL BIN1M P15 P15
T4 L3 T4 L3 GND_76 GND_76
HP_ROUT EAR_OUTR BIN1P C229 0.047uF R239 33 COMP2_Pb+ EAR_OUTR BIN1P P16 P16
P2 M1 P2 M1 GND_77 GND_77
SC1/COMP1_L_IN 2.2uF C214 AUL1 GIN1M C230 0.047uF R240 68 AUL1 GIN1M P17 P17
AV2_L_IN AV2 2.2uF C203 AUL2 GIN1P C231 0.047uF R241 33 COMP2_Y+/AV_CVBS_IN AUL2 GIN1P P18 P18
T1 N1 T1 N1 GND_79 GND_79
COMP2_L_IN 2.2uF C216 AUL3 RIN1M C232 0.047uF R242 68 AUL3 RIN1M R10 R10
R3 N3 R3 N3 GND_80 GND_80
SC1/COMP1_R_IN 2.2uF C217 AUR1 RIN1P C233 0.047uF R243 33 COMP2_Pr+ AUR1 RIN1P R11 R11
AV2_R_IN AV2 2.2uF C206 AUR2 SOGIN1 C234 1000pF AUR2 SOGIN1 R12 R12
T3 OPT T3 GND_82 GND_82
COMP2_R_IN 2.2uF C219 AUR3 AUR3 R13 R13
U2 U2 GND_83 GND_83
SCART1_Lout AUOUTL0 AUOUTL0 R14 R14
V3 V3 GND_84 GND_84
SCART1_Rout AUOUTR0 AUOUTR0 K7 K7
AUDIO OUT T2 T2 GND_EFUSE GND_EFUSE
AUVAG AUVAG
C213 C220
1uF 4.7uF
AUVRM
L214
BLM18PG121SN1D

Downloaded
AUDIO AMP(TI)
AMP_COIL_GET AMP_COIL_GET AMP_COIL_GET AMP_COIL_GET

L5603-*1 L5604-*1 L5605-*1 L5606-*1
10.0uH 10.0uH 10.0uH 10.0uH
AMP_COIL_TAIYO AMP_COIL_TAIYO AMP_COIL_TAIYOAMP_COIL_TAIYO

L5603-*2 L5604-*2 L5605-*2 L5606-*2
10.0uH 10.0uH 10.0uH 10.0uH
This parts are Located

+24V +24V_AMP
on AVSS area.
R5610
L5600
470
UBW2012-121F
C5611 4700pF
AMP_COIL_ABCO Close to Speaker

0.047uF
C5612
L5605
C5601 10uH
0.1uF
C5613 2200pF
SPK_L+
50V
C5616
0.033uF
50V
R5611
C5609 4700pF +24V_AMP 18
50V
C5608 R5609 C5626 OPT

OPT 330pF C5632 C5636
0.047uF 470 C5640 50V 0.1uF 2200pF
C5618 C5620
PVDD_AB_2
PVDD_AB_1
0.1uF 10uF 4.7uF 50V 50V

PLL_FLTP
PLL_FLTM
+3.3V_Normal 50V 35V 50V

SSTIMER
VR_ANA
3216 C5630
BST_A
OUT_A
0.47uF
AVSS
PBTL
NC_2
NC_1
OPT
C5627
50V C5637 SPEAKER_L
C5633 2200pF
330pF 50V
0.1uF
[EP] 50V
12
11
10
9
8
7
6
5
4
3
2
1
50V
AVDD 13 48 PGND_AB_2 R5612
+3.5V_ST 18
C5604 R5608 2K A_SEL_FAULT PGND_AB_1
THERMAL
14 47
0.1uF MCLK OUT_B
46
49
16V 15 SPK_L-
18K OSC_RES NC_6
16 45 50V L5606
TAS5733
IC5600
R5601 R5607 1% DVSSO 17 44 NC_5 0.033uF 10uH

10K VR_DIG BST_B C5624
AUD_MASTER_CLK 18 43 AMP_COIL_ABCO
R5603 PDN BST_C
19 42
C 100 LRCLK 20 41 NC_4 AMP_COIL_ABCO
OPT C5602 50V
OPT SCLK 40 NC_3 L5604
R5600 B 1000pF C5607 21 0.033uF 10uH
AMP_MUTE Q5600 50V SDIN OUT_C
0.1uF 22 39 C5625
10K MMBT3904(NXP) SPK_R+
SDA 23 38 PGND_CD_2
E
SCL PGND_CD_1 OPT SPEAKER_R
R5613
1/16W
24 37
C5634 C5638
C5631
25
26
27
28
29
30
31
32
33
34
35
36
0.1uF 2200pF
18
AUD_LRCK
OPT 0.47uF 50V
AUD_SCK 50V 50V
R3405
RESET
STEST
DVDD
DVSS
GND
AGND
VREG
GVDD_OUT
BST_D
PVDD_CD_1
PVDD_CD_2
OUT_D
0 AUD_LRCH C5628 OPT

POWER_DET AMP_SDA 330pF C5639
+24V_AMP 50V 2200pF
AMP_SCL C5635
0.1uF 50V
C5629 50V
C5614
C56151uF 25V
0.1uF OPT 330pF

AMP_RESET C5641 50V
+3.3V_Normal C5619 C5621
0.1uF 10uF 4.7uF
R5614
1/16W
50V 35V 50V

3216
18
C5606 SPK_R-
ZD5600
0.1uF C5617 0.033uF

L5603
16V 50V
5V
10uH
OPT
C5610 AMP_COIL_ABCO
0.1uF
16V
WAFER-ANGLE
SPK_L+
4
SPK_L-
3
SPK_R+
2
SPK_R-
1
P5600

L14 2013.10.06
FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS
ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR AUDIO[TI] 56
Downloaded
L14 MHL SW AND GATE
+3.3V_Normal
MHL_SW_AND_GATE
IC5801
74LVC1G08GW
B VCC
1 5
MHL_CD_SENSE
A
2
MHL_OCP_EN
GND Y
3 4
MHL_5V_EN

THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. MHL_SW_AND 58
Downloaded
L14 Repair Process
Copyright © 2014 LG Electronics. Inc. All rights reserved. LGE Internal Use Only

Contents of LCD TV Standard Repair Process
No. Error symptom (High category) Error symptom (Mid category) Page Remarks
1 No video/Normal audio 1
2 No video/No audio 2
3 A. Video error Tuning fail, Picture broken/ Freezing 3, 4
4 Color error 5
Vertical/Horizontal bar, residual image, light

5 6
spot, external device color error
6 No power 7
B. Power error Off when on, off while viewing, power auto
7 8
on/off
8 No audio/Normal video 9
C. Audio error
9 Wrecked audio/discontinuation/noise 10
10 Remote control & Local switch checking 11

D. Function error
11 External device recognition error 12
12 E. Noise Circuit noise, mechanical noise 13
13 F. Exterior error Exterior defect 14
* First of all, Check whether there is SVC Bulletin in GCSC System for these model.

Contents of LCD TV Standard Repair Process Detail Technical Manual
No. Error symptom Content Page Remarks
1 Check LCD back light with naked eye A1
2 LED driver B+ 24V measuring method A2
A. Video error_ No video/Normal audio
3 Check White Balance value A3
4 Power Board voltage measuring method A4
6 TUNER input signal strength checking method A5
A. Video error_ No video/Video lag/stop
7 LCD-TV Version checking method A6
9
LCD TV connection diagram A7
10
A. Video error_Color error Check Link Cable (LVDS) reconnection A8
11
condition A9
12 Adjustment Test pattern - ADJ Key A10
13 LCD TV connection diagram A8
A. Video error_Vertical/Horizontal bar, Check Link Cable (LVDS) reconnection A8
14
residual image, light spot condition A9
15 Adjustment Test pattern - ADJ Key A10
16 Exchange T-Con Board (1) A-1/5
17 Exchange T-Con Board (2) A-2/5

<Appendix>
Defected Type caused by T-Con/ 55” : driver board
18 Exchange LED driver Board (PSU) A-3/5
Inverter/ Module Other : PSU
19 Exchange Module itself (1) A-4/5

20 Exchange Module itself (2) A-5/5
Continue to the next page


Standard Repair Process
Established
Error A. Video error date 2012. 01 .14
LCD TV symptom
No video/ Normal audio Revised date 1/14
First of all, Check whether all of cables between board is inserted properly or not.
(Main B/D↔ Power B/D, LVDS Cable, Speaker Cable, IR B/D Cable,,,)
☞A1 ☞A4
Y Y Check Power Y
No video Normal Check Back Light Normal Replace T-con
On Board
Normal audio Audio On with naked eye Voltage Board or module
3.5V, 12V, 24V etc.
N N N
☞A2
Move to Check Power Board 24V output Repair Power

No video/No Board or parts
audio
Y
Normal Replace Inverter
Voltage or module
N
End
Repair Power
Board or parts
※Precaution ☞A6 & A3

Always check & record S/W Version and White
Replace Main Board Re-enter White Balance value
Balance value before replacing the Main Board

Established
Error A. Video error date 2012 . 01 .14
LCD TV symptom
No video/ No audio Revised date 2/14
☞A4
Check various Check and
No Video/ Normal Y
voltages of Power replace
No audio Voltage
Board ( 3.5V,12V, 24V) MAIN B/D
N End
Replace Power
Board and repair
parts

Established
LCD TV symptom
Picture broken/ Freezing Revised date 3/14
☞ A5 . By using Digital signal level meter

. By using Diagnostics menu on OSD
Check RF Signal level ( Menu→ Set up→ Support → Signal Test )
- Signal strength (Normal : over 50%)
- Signal Quality (Normal: over 50%)
Y Check whether other equipments have problem or not.

Normal (By connecting RF Cable at other equipment)
Signal → DVD Player ,Set-Top-Box, Different maker TV etc`
N
☞ A6
Check RF Cable
Connection Normal Y Check SVC N Check Normal Y
End
1. Reconnection Picture S/W Version Bulletin Tuner soldering Picture
2. Install Booster
N Y N
Normal N Contact with signal distributor S/W Upgrade Replace

Picture or broadcaster (Cable or Air) Main B/D
Normal N
End
Picture
End

Established
LCD TV symptom
Tuning fail, Picture broken/ Freezing Revised date 4/14
☞ A5 Check RF signal cable (DVB satellite signal or not)

Check whether other equipments have problem or not.
Check RF Signal level
(By connecting RF Cable at other equipment)
→ Set-Top-Box, Different maker TV etc
Check satellite setting. ☞ A6

- Check LNB frequency.
Normal Y Normal Y Check SVC N Check Replace
- Check satellite
Signal Setting S/W Version Bulletin Tuner soldering Main B/D
- Check Satellite connection
(DiSEqC, motor, etc…) Y
N N
Contact with signal Change satellite setting S/W Upgrade

distributor (match with installed ANT)
or broadcaster
(Cable or Air)
Normal N Normal N
Picture Picture
End Y Y
End End

Established
LCD TV symptom
Color error Revised date 5/14
☞ A8/ A9
☞A7
※ Check and Y
Check color by input
replace Link Y
-External Input Y
Color Cable Color Color
-COMPONENT Replace Main B/D Replace module
error (LVDS) and error error
-RGB
contact
-HDMI/DVI N N N
condition
Check error End

color input
mode
☞A10 External Check

External
Input/Co external Y
Check Test pattern device/Cable Replace Main B/D
mponent device and
Normal
error cable
N
Request
repair for external
device/cable
N
External Y
Check external
HDMI device/Cable
device and Replace Main B/D
error Normal
cable

A. Video error Established

Error date 2012. 01 .14
LCD TV symptom Vertical / Horizontal bar, residual image,
light spot, external device color error Revised date 6/14
Vertical/Horizontal bar, residual image, light spot Replace

Module
☞A7
☞ A8/ A9 N
Check color condition by input Check external
Check and
-External Input Screen Y device Screen Y Screen N Screen
replace Link Replace Main B/D
-Component/AV normal connection normal normal normal
Cable
-HDMI condition
N N Y Y
☞A10 Request repair End End

Replace
module for external
Check Test pattern
device
External device screen error-Color error

Connect other external
Check screen
device and cable
condition by input
External (Check normal operation of
Check N -External Input Screen N Replace
Check S/W Version Input External Input, Component
Version -Component normal Main B/D
error and HDMI by connecting
-RGB
Y Jig, pattern Generator,
-HDMI/DVI Y
Set-top Box etc.
Compo
S/W Upgrade nent
error
Request repair for
external device
Normal N Connect other external

Screen device and cable Y
(Check normal operation
Y HDMI of External Input, Screen N Replace
error Component, HDMI by normal Main B/D
connecting Jig, pattern
End Generator ,Set-top Box
etc.

Established
Error B. Power error date 2012. 01 .14
LCD TV symptom
No power Revised date 7/14
☞A11 ☞A13
DC Power on Normal N Replace
Check Power Y Check Power Y
by pressing Power Key Operati OK Power
Power LED LED On On ‘”High”
On Remote control on B/D
Stand-By : Red N Y
Replace Main B/D

Check Power cord
was inserted properly ☞A4
Measure voltage of each output of Power B/D
N
Normal Y
☞A12
※ Normal Normal Y
Y Check ST-BY 3.5V Replace Main B/D
Voltage Voltage
N N
End
Replace Power B/D Replace Power B/D

Established
Error B. Power error date 2012. 01 .14
LCD TV symptom
Off when on, off while viewing, power auto on/off Revised date 8/14
Check outlet
☞A14
CPU Y
N Check Power Off
Check A/C cord Error Abnorm Replace Main B/D Normal End
Mode
al
Check for all 3- phase Y N
power out Abnorm
al1 Replace Power B/D
☞A13
Fix A/C cord & Outlet (If Power Off mode

and check each 3 is not displayed) Normal Y
Replace Main B/D
phase out Check Power B/D Voltage
voltage
N
※ Caution
Check and fix exterior Replace Power B/D
of Power B/D Part
* Please refer to the all cases which Status Power off List Explanation
can be displayed on power off mode. "POWEROFF_REMOTEKEY" Power off by REMOTE CONTROL
"POWEROFF_OFFTIMER" Power off by OFF TIMER
"POWEROFF_SLEEPTIMER" Power off by SLEEP TIMER
"POWEROFF_INSTOP" Power off by INSTOP KEY
"POWEROFF_AUTOOFF" Power off by AUTO OFF
Normal "POWEROFF_ONTIMER" Power off by ON TIMER
"POWEROFF_RS232C" Power off by RS232C
"POWEROFF_RESREC" Power off by Reservated Record
"POWEROFF_RECEND" Power off by End of Recording
"POWEROFF_SWDOWN" Power off by S/W Download
"POWEROFF_UNKNOWN" Power off by unknown status except listed case
"POWEROFF_ABNORMAL1" Power off by abnormal status except CPU trouble
Abnormal
"POWEROFF_CPUABNORMAL" Power off by CPU Abnormal

Established
Error C. Audio error date 2012. 01 .14
LCD TV symptom
No audio/ Normal video Revised date 9/14
☞A15 ☞A16
Check user Check audio B+

No audio N Normal Y
menu  Off 24V of Power
Screen normal Voltage
Speaker off Board
Y N
Cancel OFF Replace Power Board and repair parts
Check
Disconn N
Speaker Replace MAIN Board End
ection
disconnection
Y
Replace Speaker

Established
Error C. Audio error date 2012. 01 .14
LCD TV symptom
Wrecked audio/ discontinuation/noise Revised date 10/14
→ abnormal audio/discontinuation/noise is same after “Check input signal” compared to No audio
Check input ☞A16

signal Y Wrecked Audio/ Check and replace
Signal Discontinuation/Noi Check audio
-RF speaker and
Normal se for all audio B+ Voltage (24V)
-External Input connector
signal
N
Wrecked Audio/ Y
Normal
Discontinuation/Noise Replace Main B/D
Voltage
only for D-TV
N
Wrecked Audio/
Discontinuation/Noise Replace Power B/D
only for Analog
Wrecked Audio/
Connect and check
Discontinuation/
other external Replace Main B/D End
Noise only for
device
External Input
(When RF signal is not
received) N
Normal
Request repair to external Audio
cable/ANT provider
Y
(In case of
External Input
signal error) Check and fix external device
Check and fix
external device

D. Function error Established

Error date 2012. 01 .14
LCD TV symptom
Remote control & Local switch checking Revised date 11/14
1. Remote control(R/C) operating error

Replace
Main B/D
☞A17 Y
☞A17 ☞A17
Normal Y Check & Repair N Y
Check R/C itself Normal Check B+ 3.5V Normal Check IR Normal
Operating Cable connection
Operation Voltage On Main B/D Voltage Output signal Signal
Connector solder
N Y N N
☞A4
Check R/C Operating Check & Replace Check 3.5v on Power B/D Repair/Replace
End
When turn off light Baterry of R/C Replace Power B/D or IR B/D
in room Replace Main B/D
(Power B/D don’t have problem)
If R/C operate, Normal Y
Explain the customer End
Operating
cause is interference
from light in room. N
Replace R/C

Established
Error D. Function error date 2012. 01 .14
LCD TV symptom
External device recognition error Revised date 12/14
Check technical External Input

Check Y
Signal information Technical N And Component
input Replace Main B/D
Input - Fix information information Recognition error
signal
- S/W Version
N Y
Fix in
Check and fix accordance HDMI, Optical
with technical Replace Main B/D
external device/cable Recognition error
information

Established
Error E. Noise date 2012. 01 .14
LCD TV symptom
Circuit noise, mechanical noise Revised date 13/14
Replace PSU(with LED driver)

Identify Circuit Check location OR
nose type noise of noise
Replace LED driver
Mechanical Check location of

noise noise
※ Mechanical noise is a natural ※ When the nose is severe, replace the module
phenomenon, and apply the 1st level (For models with fix information, upgrade the S/W or
description. When the customer does not provide the description)
agree, apply the process by stage.
OR
※ Describe the basis of the description in ※ If there is a “Tak Tak” noise from the cabinet,
“Part related to nose” in the Owner’s Manual. refer to the KMS fix information and then proceed
as shown in the solution manual
(For models without any fix information, provide
the description)

Established
Error F. Exterior defect date 2012. 01 .14
LCD TV symptom
Exterior defect Revised date 14/14
Zoom part with Module

Replace module
exterior damage damage
Cabinet
Replace cabinet
damage
Remote
Controller Replace remote controller
damage
Stand
Replace stand
damage

Contents of LCD TV Standard Repair Process Detail Technical Manual
Continued from previous page
No. Error symptom Content Page Remarks

21 Check front display LED A11
22 Check power input Voltage & ST-BY 3.5V A12
23 B. Power error_No power Checking method when power is ON A13
24 POWER BOARD voltage measuring method A4
25
B. Power error_Off when on, off while
26 POWER OFF MODE checking method A14
viewing
Checking method in menu when there is no
28 A15
audio
C. Audio error_No audio/Normal video
Voltage and speaker checking method when
29 A16
there is no audio
C. Audio error_Wrecked Voltage and speaker checking method in
30 A16
audio/discontinuation case of audio error
D. Function error_ No response in
31 Remote controller operation checking method A17
remote controller, key error

Standard Repair Process Detail Technical Manual
Error Established
symptom A. Video error_No video/Normal audio date
2012. 01.14
LCD TV Revised
Content Check Back Light On with naked eye date A1
<ALL MODELS>
Power On -> disjoint back case -> check lighting at 2 points.

Error Established
2012. 01 .14
LCD TV Revised
Content Inverter B+ 24V measuring method date A2
1. Measure DC 24V applying to inverter PCB from Power Board.
2. Output 24V from Power Board -> supply to inverter PCB.

Check Pin contacting statement and connection statement.

Error Established
2012. 01 .14
LCD TV Revised
Content Check White Balance value date A3
<ALL MODELS>
Entry
Entry method
method
1.
1. Press
Press the
the ADJ
ADJ button
button on
on the
the remote
remote controller
controller for
for adjustment.
adjustment.
2. Enter
2. Enter into
into White
White Balance
Balance of
of item
item 7.
6.
3.
3. After
After recording
recording the
the R,
R, G,
G, B
B (GAIN,
(GAIN, Cut)
Cut) value
value of
of Color
Color Temp
Temp (Cool/Medium/Warm),
(Cool/Medium/Warm), re-
re-
enter the value after replacing the MAIN BOARD.
enter the value after replacing the MAIN BOARD.

Error Established
symptom A. Video error_No video/ Audio date
2012. 01 .14
LCD TV Revised
Content Power Board voltage measuring method date A4
Check DC 3.5V, 12V, 24V
18 Pin (Power Board ↔ Main Board)
SMAW200-H18S5
1 Power on 2 DRV ON
3 3.5V 4 PDIM#1
5 3.5V 6 3.5V
7 GND 8 PDIM#2
9 24V 10 24V
11 GND 12 GND
13 12V 14 12V
15 12V 16 NC
17 GND 18 GND

Error Established
symptom A. Video error_Video error, video lag/stop date
2012. 01 .14
LCD TV Revised
Content TUNER input signal strength checking method A5
date
MENU => Press red key Remote controller=>signal test

=> Select channel
When the signal is strong, use the

attenuator (-10dB, -15dB, -20dB etc.)

Error Established
symptom A. Video error_Video error, video lag/stop date
2012. 01 .14
LCD TV Revised
Content LCD-TV Version checking method A6
date
1. Checking method for remote controller for adjustment
Version
Press the IN-START with the remote

controller for adjustment

Error A. Video error _Vertical/Horizontal bar, residual Established
symptom 2012. 01 .14
LCD TV image, light spot date
Revised
Content LCD TV connection diagram (1) date A7
<ALL MODELS>
As the part connecting to the external input, check the

screen condition by signal

Error
symptom
A. Video error_Color error Established
2012. 01 .14
LCD TV date
Revised
Content Check and replace Link Cable(LVDS) and contact condition date A8/A9
<ALL MODELS>
1. Check and replace LVDS Cable

2. Check LVDS connection condition

Error Established
symptom
A. Video error_Color error 2012. 01 .14
LCD TV date
Adjustment Test pattern - ADJ Key Revised
Content date A10
You can view 6 types of patterns using the ADJ Key
Checking item : 1. Defective pixel 2. Residual image 3. MODULE error (ADD-BAR,SCAN BAR..)
4.Video error (Classification of MODULE or Main-B/D!)

Appendix : Exchange T-Con Board (1)
Solder defect, CNT Broken Solder defect, CNT Broken Solder defect, CNT Broken
Solder defect, CNT Broken T-Con

T-Con Defect,
Defect,
Solder
T-Con CNT
defect,
Defect, CNT
CNT
CNT Broken
Broken
Broken
Broken Abnormal Power Section
Solder defect, Short/Crack Abnormal Power Section Solder defect, Short/Crack

Appendix : Exchange T-Con Board (2)
Abnormal Power Section Abnormal Power Section Solder defect, Short/Crack
Solder defect, Short/Crack Fuse Open, Abnormal power section Abnormal Display
GRADATION Noise GRADATION

Appendix : Exchange PSU(LED driver)
No Light Dim Light
Dim Light Dim Light
No picture/Sound Ok

Appendix : Exchange the Module (1)
Panel Mura, Light leakage Panel Mura, Light leakage Press damage
Crosstalk Press damage Crosstalk
Un-repairable Cases
In this case please exchange the module.
Press damage

Appendix : Exchange the Module (2)
Vertical Block Vertical Line Vertical Block

Source TAB IC Defect Source TAB IC Defect Source TAB IC Defect
Horizontal Block Horizontal Block Horizontal line

Gate TAB IC Defect Gate TAB IC Defect
Gate TAB IC Defect Gate TAB IC Defect Gate TAB IC Defect
Un-repairable Cases
In this case please exchange the module.
Horizontal Block
Gate TAB IC Defect
Gate TAB IC Defect

Error Established
symptom B. Power error _No power date
2012. 01 .14
LCD TV Revised
Content Check front display LED date A11
ST-BY condition: Red
Front LED control :

Menu  Option  Standby Light  On/Off

Error Established
2012. 01 .14
LCD TV Revised
Content Check power input voltage and ST-BY 5V A12
date
Check DC 3.5V, 12V, 24V
SMAW200-H18S5
1 Power on 2 DRV ON
3 3.5V 4 PDIM#1
5 3.5V 6 3.5V
7 GND 8 PDIM#2
9 24V 10 24V
11 GND 12 GND
13 12V 14 12V
15 12V 16 NC
17 GND 18 GND

Error Established
2012. 01 .14
LCD TV Revised
Content Checking method when power is ON date A13
Check “power on(Pin 1)” pin is high(about 3.3V)
SMAW200-H18S5
1 Power on 2 DRV ON
3 3.5V 4 PDIM#1
5 3.5V 6 3.5V
7 GND 8 PDIM#2
9 24V 10 24V
11 GND 12 GND
13 12V 14 12V
15 12V 16 NC
17 GND 18 GND

Error Established
symptom B. Power error _Off when on, off whiling viewing date
2012. 01 .14
LCD TV Revised
Content POWER OFF MODE checking method date A14
<ALL MODELS>
Checking order
1. Press the IN-START button of the remote controller for adjustment
2. Check the entry into adjustment item 3.

Error Established
symptom C. Audio error_No audio/Normal video 2012. 01 .14
LCD TV date
Revised
Content Checking method in menu when there is no audio date A15
<ALL MODELS>
Checking order
1. Press the MENU button on the remote controller
2. Select the AUDIO function of the Menu
3. Select TV Speaker Check

Error Established
symptom C. Audio error_No audio/Normal video date
2012. 01 .14
LCD TV Revised
Content Voltage and speaker checking method A16
when there is no audio date
<ALL MODELS>
② SMAW200-H18S5
①
1 Power on 2 DRV ON
3 3.5V 4 PDIM#1
5 3.5V 6 3.5V
7 GND 8 PDIM#2
9 24V 10 24V
11 GND 12 GND ③
13 12V 14 12V
15 12V 16 NC
17 GND 18 GND
< Main Ass’y>
Checking order
1. Check the contact condition of or 24V connector of Main Board
2. Measure the 24V input voltage supplied from Power Board
(If there is no input voltage, remove and check the connector)
3. Connect the tester RX1 to the speaker terminal and if you hear the Chik Chik sound
when you touch the GND and output terminal, the speaker is normal.

Error D. Function error_ No response in remote controller, Established
symptom key error 2012. 01 .14
LCD TV date
Revised
Content Remote controller operation checking method date A17
<ALL MODELS>
P4600
1 GND
2 KEY1
3 KEY2
③
4 3.5V_ST
5 GND
6 LED_R
④ 7 IR
② 8 GND
① < Sub Ass’y>
9 SCL
10 SDA
< Main Ass’y>
Checking order
1, 2. Check IR cable condition between IR & Main board.
3. Check the st-by 3.3V on the terminal 4.
4. When checking the Pre-Amp when the power is in ON condition, it is normal when the Analog
Tester needle moves slowly, and defective when it does not move at all.

Led TV: Service Manual

Uploaded by

Copyright:

Available Formats

Led TV: Service Manual

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Led TV: Service Manual

Uploaded by

Copyright:

Available Formats

Internal Use Only

North/Latin America http://aic.lgservice.com

MODEL : 42LB55** 42LB55**-Z*

P/NO : MFL68003704 (1312-REV00) Printed in Korea

Downloaded from www.Manualslib.com manuals search engine

SAFETY PRECAUTIONS ......................................................................... 3

SERVICING PRECAUTIONS ................................................................... 4

ADJUSTMENT INSTRUCTION .............................................................. 10

EXPLODED VIEW .................................................................................. 17

SCHEMATIC CIRCUIT DIAGRAM ..............................................................

Downloaded from www.Manualslib.com manuals search engine

IMPORTANT SAFETY NOTICE

General Guidance Leakage Current Hot Check (See below Figure)

Before returning the receiver to the customer,

Always perform an AC leakage current check on the exposed

Leakage Current Cold Check(Antenna Cold Check)

Downloaded from www.Manualslib.com manuals search engine

Downloaded from www.Manualslib.com manuals search engine

Fuse and Conventional Resistor

Downloaded from www.Manualslib.com manuals search engine

1. Application range 3. Test method

1) Temperature: 25 °C ± 5 °C(77 °F ± 9 °F), CST: 40 °C ± 5 °C

4. Model General Specification

DTV (MPEG2/4, DVB-T2): 8 countries

DTV (MPEG2/4, DVB-C): 37 countries

DTV (MPEG2/4,DVB-S): 29 countries

Supported satellite : 22 satellites

Downloaded from www.Manualslib.com manuals search engine

Satellite Digital TV * DVB-S/S2 (Satellite model only support )

Downloaded from www.Manualslib.com manuals search engine

5.2. HDMI Input(PC/DTV)

Downloaded from www.Manualslib.com manuals search engine

6.3. USB Input

6.4. DLNA Input

6.5. 3D Input mode

Downloaded from www.Manualslib.com manuals search engine

Case1 : Software version up

Downloaded from www.Manualslib.com manuals search engine

<Caution> Never connect HDMI cable when EDID downloaded.

Downloaded from www.Manualslib.com manuals search engine

Downloaded from www.Manualslib.com manuals search engine

auto controller or push Adjustment R/C P-ONLY → Enter the

* Auto-control interface and directions How to adjust

Downloaded from www.Manualslib.com manuals search engine

(2) When 3D OSD appear automatically , then select OK key.

Result) I f, The LED light is green and the Module shows

4.5. Outgoing condition Configuration

4.3. IR emitter inspection

Downloaded from www.Manualslib.com manuals search engine

6. Model name & Serial number D/L

4) Check the model name Instart menu. → Factory name displayed.

6.1. Signal Table

Downloaded from www.Manualslib.com manuals search engine

7.1.2 Download method

7.2.2. LAN inspection solution

(2) MAC Address & CI+ Key Download

7.3. LAN PORT INSPECTION(PING TEST)

7.3.1. Equipment setting

Downloaded from www.Manualslib.com manuals search engine

MODEL : 42LB55 42LB55-Z*

(2) When 3D OSD appear automatically , then select OK key.

Result) I f, The LED light is green and the Module shows

4) Check the model name Instart menu. → Factory name displayed.

+1.5V_DDR Vout=1.25(1+R2/R1)+IadjR2 L407 C417

D803-1 D804-1 D805-1 D806-1

D803-2 D804-2 D805-2 D806-2