Clock 1
Clock 1
Clock 1
Clock1
9 2 Front pin 11
20
10 2 cover pin 11
11 3 Securing pin
12 1 Clock dial
13 2 Dial spacer
14 1 Pendulum head 25
36
15 1 Pendulum pivot 25
16 1 Pendulum rod 35 26
17 1 Pendulum bob 28
18 1 Pendulum nut 27
19 6 Shaft cover
20 1 Shaft151
33
21 1 yoke 31
22 1 escape 32
29
23 1 Pallet2
30
24 1 Pallet1
47 35
25 1 Timing 30
26 1 16teeth
27 2 Shaft140
28 2 Sleeve119
29 1 Shaft175
30 2 15teeth_1.5 49
1
31 1 Pawl 38
32 1 Sleeve70 37 28
33 2 15teeth 40
34 1 drum
35 3 60teeth 48 34
36 1 Ratchet 2
37 1 Pawl pin 44 45
38 1 32teeth
39 1 10teeth
40 1 sleeve18 33
12
41 8 ropering 27
42 1 rope 8
43 1 Weight 10
44 1 shaft30
46 35
45 1 8teeth
46 1 30teeth
47 1 Key shaft 3
48 1 Minute hand
4
49 1 Hour hand
9
43
10
10
10
39.75
DIAL NOT SECTIONED 39
15
14 14 B
6
4
16
19
13
16
12
19
B (1 : 2)
13
10
19
17
8
C
3
7
16
10
R62.5
50 60
1 BACK 1-off
SCALE 1:2
20 6 6 6 6 13 R3
664
81 86.7
50 49 42.4 38.6 36.2 51.3 46 40.7 39.3 51.6
R62.5
42 50
4 FRONT 1-off
SCALE 1:2 6.1
20 6 10 6 8 6 6 10 20 8.6
6 55.5 98
502
48 A
57 12 12
50 75 75 12 20
R62.5
6.1
42 50 30
252
R2 A-A (1 : 1)
6 PENDULUM HANGER 1-OFF
A
58
25
23 48
3 15
ANGLED BRACE 1-off
90° 25
13
5
130
20 12 30 13 6 30 13
10 120
20
40 11 SECURING PIN 3-off
13
50 10 COVER PIN 2-off
18 3
30 SQ 7 WALL SPACER 2-off 3
6 TAP M6
300
55
20 210
10
20
2 holes DRILLED FROM
28 THE BACK 6MM DEEP
75
252
40°
1076 20
21.8
30
6.5
120
10
17 PENDULUM BOB 1-off
25
10
3.2
34.5
43.1
R1.6
69
6.1
28.7
18.4
10
8
12.6 46 30TEETH 1-off
N
33 15 TEETH 1-off N-N
R1.6
I
23
78
R1.6 R5
R2.4 6
3.2 73
51.8 10 36.8
13
17.2 67.9
39 10 TEETH 1-off 10
43.1
31
26 16 TEETH 1-off
38 32 TEETH 1-off
I I-I
53
6 142.6
6
Tight fit on shaft
35 60 TEETH 1-OFF
R6
135.7
35 60 TEETH 1-OFF
35 60 TEETH 2-OFF 10
3.2 132.2
R6 258° 1.9
1
23.3
20.3
6
148.1
10
138.4 50
13
36 RATCHET 1-OFF
10
2.2
R25.5
27.53°
7
24.9
O 125°
O-O (1 : 1)
53
PAWL 1-OFF
31
74.3 10 19.5
R7.5
6.1
ESCAPEMENT 1-OFF 6 20 90°
TRUE R3 22 TRUE R3
38 13 13
6
37.1
36.3 R5
21 10
YOKE 1-off
92°
8.6 34 DRUM 1-OFF
19.8
69.17° 6
4.7
175
6.8
44.63°
29 SHAFT 175 1-OFF
151
6
10 6.1
1 70
44 SHAFT 30 1-OFF
32 6.1 10
119.5
13 2
9.5 9.5 8
20
SHT 10 OF 10 SHTS LAW WOODEN CLOCK 1 Shafts and sleeves
9.5
8. Care should be taken to adjust the pallets (23 & 24) relative to the timing
wheel. They should operate to allow the timing wheel to move
incrementally forward when swinging through a small arc of movement of
the pendulum. (<10°).
9. The pitch of the gears is controlled by the drilling of the hole centres in the
front and back frames. It may help to delay the drilling of these holes in
the frames until after the gears are first cut and then linished to size. At
this point it would help to mount them on two separate pieces of wood and
test there free movement one to the other and measure the centre
distance between them, so that the hole centres can be drilled at this
dimension rather than the theoretical dimension on the drawing.
10. The winder used is not drawn on the plans but a simple 'T' bar with a
square hole in the end to engage over the end of the square end of the
shaft holding the winding gears.
11. The profiling of the larger gears is not necessary to the functioning of the
clock, and can be carried out at the discretion of the clock builder. Notes LAW WOODEN CLOCK 1