Weld Defects

What is Welding Defects?
Welding Defects can be defined as the irregularities formed in the given weld metal due to wrong
welding process or incorrect welding patterns, etc. The defect may differ from the desired weld bead
shape, size, and intended quality. Welding defects may occur either outside or inside the weld metal.
Some of the defects may be allowed if the defects are under permissible limits but other defects such as
cracks are never accepted.
Types
Welding defects can be classified into two types as external and internal defects:
External Welding Defects:
1. Weld Crack
2. Undercut
3. Spatter
4. Porosity
5. Overlap
6. Crater
Internal welding
1. Slag Inclusion
2. Incomplete Fusion
3. Necklace cracking
4. Incompletely filled groove or Incomplete penetration
External Welding Defects
The various types of external defects with their causes and remedies are listed below:
1. Weld Crack
This is the most unwanted defect of all the other welding defects. Welding cracks can be present at the
surface, inside of the weld material or at the heat affected zones.
Crack can also appear at different temperatures:
Hot Crack – It is more prominent during crystallization of weld joints where the temperature
can rise more than 10,000-degree Celsius
Cold Crack – This type of crack occurs at the end of the welding process where the temperature is quite
low. Sometimes cold crack is visible several hours after welding or even after few days.
Causes Of Weld Crack:
1. Poor ductility of the given base metal.

2. The presence of residual stress can cause a crack on the weld metal.
3. The rigidity of the joint which makes it difficult to expand or contract the metals.
4. If there is high content on sulfur and carbon then also the cracks may appear.
5. Using hydrogen as a shielding gas while welding ferrous materials.
Remedies for Weld crack:
1. Using appropriate materials may decrease the chances of crack.

2. Preheating the weld and reducing the cooling speed joint helps in reducing crack.
3. Reduce the gap between the weld joints by using reasonable weld joints.
4. While welding releases the clamping force slowly which increases fill to capacity of welding
material.
2. Undercut
When the base of metal melts away from the weld zone, then a groove is formed in the shape of a
notch, then this type of defect is known as Undercut. It reduces the fatigue strength of the joint.
Causes of Undercut:
1. If the arc voltage is very high then this defect may occur.
2. If we use the wrong electrode or if the angle of the electrode is wrong, then also the defect
may form.
3. Using a large electrode is also not advisable.
4. High electrode speed is also one of the reasons for this defect.
Remedies for Undercut:
1. Reduce the arc length or lower the arc voltage.

2. Keep the electrode angle from 30 to 45 degree with the standing leg.
3. The diameter of the electrode should be small.
4. Reduce the travel speed of the electrode.
3. Spatter
When some metal drops are expelled from the weld and remain stuck to the surface, then this
defect is known as Spatter.
Causes Of Spatter:
1. High Welding current can cause this defect.

2. The longer the arc the more chances of getting this defect.
3. Incorrect polarity.
4. Improper gas shielded may also cause this defect.
Remedies for Spatter:
1. Reducing the arc length and welding current

2. Using the right polarity and according to the conditions of the welding.
3. Increasing the plate angle and using proper gas shielding.
4. Porosity
Porosity in the condition in which the gas or small bubbles gets trapped in the welded zone.
Causes of Porosity:
1. It occurs when the electrode is not coated properly.
2. Using a longer arc may also increase its chances.
3. Increased welding currents.
4. Rust or oil on the welding surface.
Remedies for porosity:
1. Proper selection of the electrode.

2. Decreasing the welding current.
3. Using smaller arc and slowing the process to allow the gases to escape.
4. Remove rust or oil from the surface and use a proper technique
5. Overlap
When the weld face extends beyond the weld toe, then this defect occurs. In this condition the
weld metal rolls and forms an angle less than 90 degrees.
Causes of Overlap:
Causes of Overlap:
1. Improper welding technique.

2. By using large electrodes this defect may occur.
3. High welding current
Remedies for Overlap:
1. Using a proper technique for welding.

2. Use small electrode.
3. Less welding current.
6. Crater
It occurs when the crater is not filled before the arc is broken, which causes the outer edges to
cool faster than the crater. This causes a stress and then crack is formed.
Causes of the crater:
1. Incorrect torch angle.

2. Use of large electrode:
3. Improper welding technique
Remedies for crater:
1. Using a proper torch angle may reduce the stress on the metal
2. Using a small electrode may also decrease the crater.
3. Use a proper technique.
Internal Welding Defects
The various types of internal welding defects with their causes and remedies are listed below:
1. Slag Inclusion
If there is any slag in the weld, then it affects the toughness and metal weldability of the given
material. This decreases the structural performance of the weld material. Slag is formed on the
surface of the weld or between the welding turns.
Causes Of Slag:
1. Slag is formed if the welding current density is very small, as it does not provide the required
amount of heat for melting the metal surface.
2. If the welding speed is too fast then also slag may occur.
3. If the edge of the weld surface is not cleaned properly then also slag may form.
4. Improper welding angle and travel rate of welding rod.
Remedies for Slag Inclusion:
1. Increase the current density

2. Adjust the welding speed so that the slag and weld pool do not mix with each other.
3. Clean the weld edges and remove the slags of previous weld layers
4. Have a proper electrode angle and travel rate.
2. Incomplete Fusion
Incomplete fusion occurs when the welder does not accurately weld the material and the metal
pre solidifies which leads to a gap which is not filled with the molten metal.
Causes of Incomplete fusion:
1. It occurs because of the low heat input.

2. When the weld pool is very large and runs ahead of the arc.
3. When the angle of the joint is too low.
4. Incorrect electrode and torch angle may also lead to incomplete fusion.
5. Unproper bead position.
Remedies for Incomplete Fusion:
1. Increasing the welding current and decreasing the travel speed helps in removing the chances
of incomplete fusion.
2. Reducing the deposition rate.
3. Increasing the joint angle.
4. Try to position the electrode and torch angle properly so that the edges of the plate melt away.
5. Positioning the bead properly so that the sharp edges with other beads can be avoided.
3. Necklace Cracking
It occurs in the use of electron beam welding where the weld does not penetrate properly.
Therefore, the molten metal does not flow into the cavity and results in a cracking known as
“Necklace Cracking”.
Causes of Necklace Cracking:
1. Improper welding technique.
2. It occurs in materials such as nickel base alloys, stainless steel, carbon steels and Tin alloys.
3. Using high speed of electron beam welding
Remedies for Necklace Cracking:
1. Using a proper welding technique reduce the chances of necklace cracking.
2. Using proper materials for welding.
3. Using a constant speed during the welding process.
4. Incompletely Filled Groove or Incomplete Penetration
These defects occur only in the butt welds where the groove of the metal is not filled completely.
It is also called as incomplete penetration defect.
Causes of an Incomplete filled groove are:
1. Less deposition of the weld metal

2. Use of improper size of the electrode
Remedies for Incomplete filled groove are:

1. More deposition of the weld metal.
2. Use a proper size of the electrode.
3. By using a proper welding technique.
Therefore, we have listed all types of welding defects present during any manufacturing
process.While welding, it is very important to remove all the defects of welding present in the
workpiece.
If there would be defects in the welding material, then in severe conditions the components of
the material would fail which may lead to loss of property and sometimes also life.

Weld Defects

Uploaded by

Copyright:

Available Formats

Weld Defects

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Weld Defects

Uploaded by

Copyright:

Available Formats

What are the main types of welding defects?

What are the main types of welding defects?

What causes incomplete fusion?

What causes incomplete fusion?

What is Welding Defects?

External Welding Defects:

4. Incompletely filled groove or Incomplete penetration

External Welding Defects

Crack can also appear at different temperatures:

Causes Of Weld Crack:

1. Poor ductility of the given base metal.

1. Using appropriate materials may decrease the chances of crack.

Remedies for Undercut:

1. Reduce the arc length or lower the arc voltage.

1. High Welding current can cause this defect.

Remedies for Spatter:

1. Reducing the arc length and welding current

Remedies for porosity:

1. Proper selection of the electrode.

1. Improper welding technique.

Remedies for Overlap:

1. Using a proper technique for welding.

1. Incorrect torch angle.

Remedies for crater:

Internal Welding Defects

4. Improper welding angle and travel rate of welding rod.

Remedies for Slag Inclusion:

1. Increase the current density

Causes of Incomplete fusion:

1. It occurs because of the low heat input.

Remedies for Incomplete Fusion:

1. Improper welding technique.

3. Using high speed of electron beam welding

Remedies for Necklace Cracking:

1. Using a proper welding technique reduce the chances of necklace cracking.

2. Using proper materials for welding.

3. Using a constant speed during the welding process.

3. Improper welding technique

4. Incompletely Filled Groove or Incomplete Penetration

Causes of an Incomplete filled groove are:

1. Less deposition of the weld metal

Remedies for Incomplete filled groove are:

You might also like