Power Requirements: Guitar Audio Buffer/Splitter
Power Requirements: Guitar Audio Buffer/Splitter
Power Requirements: Guitar Audio Buffer/Splitter
This warranty applies only to the original owner and is not • Three outputs allow a single guitar signal to
INPUT: Standard 1/4” mono jack that should be feed a tuner and two amplifiers without signal
connected to the output of an electric transferable.
loss and/or tonal degradation.
guitar or the output of an effect pedal.
This warranty does not cover damage to the product as a
result from accident or misuse. • Two of the three outputs are connected in
MAIN OUT: Standard 1/4” mono jack that should be
connected to the input of an amplifier or parallel, and the third is Transformer Isolated to
This warranty will be canceled at the sole discretion of prevent Ground Loop Hum/Noise when driving
the input of an effect pedal. Axess Electronics if the product has:
two amplifiers.
ISO’D OUT: Standard 1/4” mono jack that should be (1) Any signs of tampering, unauthorized service, or
connected to (1) the input of a second modifications. • The Transformer Isolated output is equipped
amplifier or (2) the input of an effect (2) Any damage resulting from physical abuse or failure with a Phase Reverse switch to prevent any
pedal feeding a second amplifier or (3) to follow the operating instructions. phase cancellation problems from occurring
the input of a tuner to prevent Ground when driving two amplifiers.
Loop Hum/Noise or other noise Axess Electronics’ liability to the owner and under this
problems that can be caused by some warranty is limited only to the repair or replacement of the • Powered by a 9VDC Adapter (we recommend
tuners... Please note that if any pedals defective product. Call or write to Axess Electronics prior the Boss PSA-100/110/120/220/230 or 240
are used between the ISO’D OUT jack to shipping the product for repair.
depending on your local AC supply voltage)
and a second amplifier, these pedals with a 5.5mm/2.1mm barrel connector.
must be powered from a different source Axess Electronics reserves the right to make any changes
and/or improvements to the design of this product without
than the BS2, tuner and pedals feeding Brushed finish with black anodize coating and
any obligation to include those changes in any previously •
the first amplifier otherwise a Ground manufactured units. laser-engraved printing.
Loop will be created resulting in
unwanted hum and noise...
How To Reach Us • Housed in a compact (4.40" x 2.40" x 1.30")
SPLIT OUT: Standard 1/4” mono jack that is and rugged 0.064” thick aluminum enclosure for
connected directly (in parallel) to the Mail: Axess Electronics years of reliable use and performance.
251 Queen Street South #278
MAIN OUT jack. Use this jack whenever
Mississauga, Ontario L5M1L7
a transformer-isolated signal/split is not Canada
necessary, such as when feeding the
input of a pedal and/or some tuners… Tel.: 416-410-9688
MAIN
SPLIT
MAIN
SPLIT
can’t always be the case. Some Fuzz and WAH pedals GUITAR /
do not like to be fed with a buffered signal. If you find BS2 EFFECTS AMP BS2 AMP#1
these pedals don't sound right with the buffer in front of ISO'D
EFFECTS ISO'D
them, simply connect the buffer after these devices. In
this situation, it would be ideal if these pedals had true-
bypass switching to ensure the BS2 gets the best
possible signal it can... Using the BS2 in this AMP#2
application will prevent the loss of (1) signal level, (2)
high end frequency response and (3) low end punch
TUNER
that is caused by cable capacitance and poorly
designed input stage/circuitry of some effect pedals.
MAIN
SPLIT
As a splitter for driving two amplifiers with the same
effect pedals, the BS2 must be used last in the signal BS2 EFFECTS AMP#1 TUNER
chain so that both amplifiers get the same sound... If ISO'D
using the BS2 in this manner, you may want to
consider getting a second one to use as a buffer to
MAIN
prevent some of the losses described above (using the SPLIT
BS2 as a buffer). If one of the amps is to get a dry un- AMP#2 BS2#1 EFFECTS
effected signal or is to be fed with a separate chain of ISO'D
pedals, then the BS2 can be used as a buffer and the
second amplifier or pedals can simply be fed with a
signal from the ISO’D OUT jack (to prevent Ground
Loop Hum/Noise).
MAIN
SPLIT
Please note that if any pedals are used between the
TUNER BS2#2 AMP#1
ISO’D OUT jack and the second amplifier, these pedals ISO'D
must be powered from a different power source than
the BS2, tuner and pedals feeding the first amplifier
MAIN
SPLIT
otherwise a Ground Loop will be created resulting in
unwanted hum and noise... BS2 EFFECTS AMP#1 AMP#2
ISO'D
In all of the above applications, the SPLIT OUT jack
can be used to feed the input of a tuner as long as the
MAIN
tuner doesn’t cause a Ground Loop (resulting in SPLIT
unwanted hum and noise) or other noise problems that EFFECTS AMP#2 EFFECTS BS2
some tuners are known for… ISO'D
These effects must be powered from a Using the BS2 to solve
different source than the BS2, tuner and existing Ground Loop Hum/ AMP
effects for AMP#1 otherwise a Ground Noise problem s in a rig...
L o o p wi l l b e c r e a t e d r e s u l t i n g i n
unwanted hum and noise...