Technical Project Proposal #537/19: PVC (V01/2019)
Technical Project Proposal #537/19: PVC (V01/2019)
Technical Project Proposal #537/19: PVC (V01/2019)
HORIZONTAL PLANE
2. COMPENSATION LAYER
Application:
GEOLAND HT is loose laid without tension and must be free from folds and
wrinkles with approx. 10-15 cm overlap of the edges; place in direct contact
with the support avoiding any gaps or voids between the substrate and the
geotextile.
Note: The mechanical properties of the geotextile used will still have to be
evaluated based on actual conditions of the site.
3. WATERPROOF MEMBRANE
Application:
Laying system:
Mechanically fixed with prepunched galvanised steel Flag bar
around the perimeter on the vertical wall close to the corner
8 cm overlap for welding field sheet
All welding including detail work to be carried out in dry conditions using:
Leister automatic welder
Leister hot air gun
Waterproofing test and control: no destructive mechanical test with
Welding tester, pneumatic welding test and test of triple points and patches
with vacuum cap.
Setting performed by technicians approved by SOPREMA srl.
Finishing and accessories composed by elements produced and approved
by SOPREMA srl.
Insert Flag Bar End Protectors at the junction between two adjacent bars.
IMPORTANT NOTE:
- Apply profiles and fixation elements in 316 stainless steel if the tank
contain aggressive substances that are not compatible with standard
Flag metal profiles (seawater, acids or other).
In any case, contact the SOPREMA Technical Department to verify the
compatibility of the PVC membrane with the dissolved substances in
the water contained in the tank.
2. COMPENSATION LAYER
Application:
GEOLAND HT is loose laid without tension and must be free from folds and
wrinkles with approx. 10-15 cm overlap of the edges; place in direct contact
with the support avoiding any gaps or voids between the substrate and the
geotextile.
Note: The mechanical properties of the geotextile used will still have to be
evaluated based on actual conditions of the site.
3. WATERPROOF MEMBRANE
Specifications:
Tensile strength (L/T) > 17 N/mm2 UNI EN 527-3
Elongation at break (L/T) ≥ 300% UNI EN 527-3
Cold bending ≤ -30 °C UNI EN 495-5
Water permeability < 10-6m3m-2d-1 UNI EN 14150
Application:
Laying system:
PVC Flagmetal strip, 5 cm wide. It is a zinc steel strip coated with
Flagon PVC membrane. Fix each 2 meters using rawlplugs and
appropriate fixings. Weld on them the PVC waterproof membrane.
PVC Flagmetal termination strip, 7 cm wide, around perimeter top.
It is a zinc steel strip coated with Flagon PVC membrane. Fix using
rawlplugs and appropriate fixings. Weld on them the PVC
waterproof membrane.
All welding including detail work to be carried out in dry conditions using:
Leister automatic welder
Leister hot air gun
Waterproofing test and control: no destructive mechanical test with
Welding tester and test of triple points and patches with vacuum cap.
Setting performed by technicians approved by SOPREMA srl.
Finishing and accessories composed by elements produced and approved
by SOPREMA srl.
Note: the Flagmetal termination strip shall not be sealed on top with
silicone mastic or with permanent sealants. The profile must allow the
release of any air or gas under the sealing element.
4. PIPELINES
IMPORTANT NOTE:
- Apply profiles and fixation elements in 316 stainless steel if the tank
contain aggressive substances that are not compatible with standard
Flag metal profiles (seawater, acids or other).
In any case, contact the SOPREMA Technical Department to verify the
compatibility of the PVC membrane with the dissolved substances in
the water contained in the tank.