Manual Del Equipo
Manual Del Equipo
Manual Del Equipo
EQUIPO
Electric Chain
Operating, Maintenance
& Parts Manual
TM
Rated Loads
1/4 through 2-Tons
250 through 2000 kg.
Serial Number______________________________________
Voltage ____________________________________________
24761 624-V
i
CM HOIST PARTS AND SERVICES ARE AVAILABLE IN THE UNITED STATES AND IN CANADA
As a CM Hoist user, you are assured of reliable repair and parts services through a network of Master Parts Depots and
Service Centers that are strategically located in the United States and Canada. These facilities have been selected on the
basis of their demonstrated ability to handle all parts and repair requirements promptly and efficiently.
Below is a list of the Master Parts Depots in the United States and Canada. To quickly obtain the name of the U.S. Service
Center located nearest you, call (800) 888-0985. Fax: (716) 689-5644. In the following list, the Canadian Service Centers are
indicated.
SAFETY PRECAUTIONS
Each Valustar Electric Hoist is built in accordance with the specifications contained herein and at the time of manufacture com-
plied with our interpretation of applicable sections of the *American Society of Mechanical Engineers Code B30.16 “Overhead
Hoists,” the National Electrical Code (ANSI/NFPA 70) and the Occupational Safety and Health Act. Since OSHA states the
National Electrical Code applies to all electric hoists, installers are required to provide current overload protection and grounding
[on the branch circuit section] in keeping with the code. Check each installation for compliance with the application, operation
and maintenance sections of these articles.
The safety laws for elevators, lifting of people and for dumbwaiters specify construction details that are not incorporated into the
hoists. For such applications, refer to the requirements of applicable state and local codes, and the American National Safety
Code for elevators, dumbwaiters, escalators and moving walks (ASME A17.1). Columbus McKinnon Corporation cannot be
L L
responsible for applications other than those for which CM equipment is intended.
*Copies of this standard can be obtained from ASME Order Department, 22 Law Drive, Box 2300, Fairfield, NJ 07007-2300, U.S.A.
THIS SYMBOL POINTS OUT IMPORTANT SAFETY INSTRUCTIONS WHICH IF NOT FOLLOWED
COULD ENDANGER THE PERSONAL SAFETY AND/OR PROPERTY OF YOURSELF AND
! OTHERS. READ AND FOLLOW ALL INSTRUCTIONS IN THIS MANUAL AND ANY PROVIDED
WITH THE EQUIPMENT BEFORE ATTEMPTING TO OPERATE YOUR VALUSTAR HOIST. !
L
24. NOT operate a hoist unless load slings or other
! WARNING approved single attachments are properly sized and
Improper operation of a hoist can create a potentially haz-
seated in the hook saddle.
ardous situation which, if not avoided, could result in death or
25. Take up slack carefully - make sure load is balanced and
serious injury. To avoid such a potentially hazardous situation,
the operator shall:
load holding action is secure before continuing.
26. Shut down a hoist that malfunctions or performs unusually
and report such malfunction.
1. NOT operate a damaged, malfunctioning or unusually 27. Make sure hoist limit switches function properly.
performing hoist. 28. Warn personnel of an approaching load.
L
2. NOT operate the hoist until you have thoroughly read
and understood this Operating, Maintenance and Parts
Manual.
3. NOT operate a hoist which has been modified (without ! CAUTION
the manufacturer’s approval or without certification that it Improper operation of a hoist can create a potentially haz-
ardous situation which, if not avoided, could result in minor or
moderate injury. To avoid such a potentially hazardous situa-
is in conformity with ANSI/AMSE B30 volumes).
tion, the operator shall:
4. NOT lift more than rated load for the hoist.
5. NOT use hoist with twisted, kinked, damaged, or worn
load chain. 1. Maintain a firm footing or be otherwise secured when
6. NOT use the hoist to lift, support, or transport people. operating the hoist.
7. NOT lift loads over people. 2. Check brake function by tensioning the hoist prior to
8. NOT operate a hoist unless all persons are and remain each lift operation.
clear of the supported load. 3. Use hook latches. Latches are to retain slings, chains,
9. NOT operate unless load is centered under hoist. etc. under slack conditions only.
10. NOT attempt to lengthen the load chain or repair dam- 4. Make sure the hook latches are closed and not support-
aged load chain. ing any parts of the load.
11. Protect the hoist’s load chain from weld splatter or other 5. Make sure the load is free to move and will clear all
damaging contaminants. obstructions.
12. NOT operate hoist when it is restricted from forming a 6. Avoid swinging the load or hook.
straight line from hook to hook in the direction of loading. 7. Make sure hook travel is in the same direction as shown
13. NOT use load chain as a sling, or wrap load chain on the controls.
around load. 8. Inspect the hoist regularly, replace damaged or worn
14. NOT apply the load to the tip of the hook or to the hook parts, and keep appropriate records of maintenance.
latch. 9. Use the hoist manufacturer’s recommended parts when
15. NOT apply the load unless load chain is properly seated repairing the unit.
in the chain wheel(s) or sprocket(s). 10. Lubricate load chain per hoist manufacturer’s
16. NOT apply load if bearing prevents equal loading on all recommendations.
load supporting chains. 11. NOT use the hoist load limiting or warning device to
17. NOT operate beyond the limits of the load chain travel. measure load.
18. NOT leave load supported by the hoist unattended 12. NOT use limit switches as routine operating stops unless
unless specific precautions have been taken. allowed by manufacturer. They are emergency devices
19. NOT allow the load chain or hook to be used as an elec- only.
trical or welding ground. 13. NOT allow your attention to be diverted from operating
20. NOT allow the load chain or hook to be touched by a the hoist.
live welding electrode. 14. NOT allow the hoist to be subjected to sharp contact
21. NOT remove or obscure the warnings on the hoist. with other hoists, structures, or objects through misuse.
22. NOT operate a hoist on which the safety placards or 15. NOT adjust or repair the hoist unless qualified to per-
decals are missing or illegible. form such adjustments or repairs.
23. NOT operate a hoist unless it has been securely
attached to a suitable support.
iii
L
! WARNING – DO NOT LIFT MORE THAN RATED LOAD.
L
! WARNING
– DO NOT OPERATE DAMAGED OR MALFUNCTIONING HOIST.
– DO NOT OPERATE WITH TWISTED, KINKED OR DAMAGED
CHAIN.
2 INSPECT
All hoists should be visually inspected service until repairs are made. ings are enlarged beyond normal throat
before use, in addition to regular, periodic Under no circumstances should you oper- opening should not be used. If latch does not
maintenance inspections. ate a malfunctioning hoist. engage throat opening of hook, hoist should
Inspect hoists for operational warning Check chain for gouged, twisted, distorted be taken out service.
notices and legibility. links and foreign material. Do not operate Check for misphasing – hook travel should
Deficiencies should be noted and brought hoists with twisted, kinked or damaged chain. correspond to control direction.
to the attention of supervisors. Be sure Load chain should be properly lubricated.
defective hoists are tagged and taken out of Hooks that are bent, worn or whose open-
L
! WARNING
– DO NOT PULL AT AN ANGLE. BE SURE HOIST AND LOAD
ARE IN A STRAIGHT LINE.
Be sure hoist is solidly held in Be sure hoist and load are in a Be sure load is hooked securely. Do not use load chain as a sling. Do not operate with hoist head
the uppermost part of the support straight line. Do not pull at an Do not tip load the hook. Do not Such usage damages the chain resting against any object. Lift the
hook arc. angle. load hook latch. Hook latch is to and lower hook. load gently. Do not jerk it.
prevent detachment of load under
slack chain conditions only.
L
! WARNING – DO NOT LIFT PEOPLE OR LOADS
OVER PEOPLE.
4 LIFT PROPERLY
Do not lift co-workers with a hoist.
5 MAINTAIN PROPERLY
CLEANING: Hoists should be kept clean
Make sure everyone is clear of the load and free of dust, dirt, moisture, etc., which
when you lift. will in any way affect the operation or safe-
Do not remove or obscure operational ty of the equipment.
warning notices. LUBRICATION: Chain should be properly
lubricated.
AFTER REPAIRS: Carefully operate the
hoist before returning it to full service.
VIOLATION OF ANY OF THESE WARNINGS LISTED MAY RESULT IN SERIOUS PERSONAL INJURY TO THE
OPERATOR OR NEARBY PERSONNEL BY RELEASED LOAD OR BROKEN HOIST COMPONENTS.
1
FOREWORD
This manual contains important information to help you properly install, operate and maintain your hoist for maximum perfor-
mance, economy and safety.
Please study its contents thoroughly before putting your hoist into operation. By practicing correct operating procedures and by
carrying out the recommended preventive maintenance suggestions, you will experience long, dependable and safe service.
After you have completely familiarized yourself with the contents of this manual, we recommend that you carefully file it for future
reference.
The information herein is directed to the proper use, care and maintenance of the hoist and does not comprise a handbook on
the broad subject of rigging. Rigging can be defined as the process of lifting and moving heavy loads using hoists and other
information, we recommended consulting a standard textbook on the subject.
TABLE OF CONTENTS
OPERATING INSTRUCTIONS 3
Series 635 Motor Driven Trolley . . . . . . . . . . . . . . . . . . . .3
4
Rigid Lug Suspension . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
5
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 Chain Container . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
6
Hoist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 Suspension Assemblies . . . . . . . . . . . . . . . . . . . . . . . . . .4
7
Hoist with Low Headroom Trolley . . . . . . . . . . . . . . . . . . .9 Load Chain Attachment . . . . . . . . . . . . . . . . . . . . . . . . . .5
8
Hoist with Motor Driven Trolley . . . . . . . . . . . . . . . . . . . . .9 Series 635 Low Headroom Trolley . . . . . . . . . . . . . . . . . .6
9
Safety Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 Attaching Hoist to Trolley . . . . . . . . . . . . . . . . . . . . . . . . .6
INSPECTION
10
Hook Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
11
Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 Gaging Load Chain Wear . . . . . . . . . . . . . . . . . . . . . . . .11
12
Frequent Inspections . . . . . . . . . . . . . . . . . . . . . . . . . .9,10 Typical Wiring Diagrams . . . . . . . . . . . . . . . . . . . . . . . . .15
13
Periodic Inspections . . . . . . . . . . . . . . . . . . . . . . . . . .9,10 Hook Suspension . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
14
Preventive Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . .9 Centrifugal Mechanism Assembly . . . . . . . . . . . . . . . . .16
15
Hook Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 Cutting Chain by Nicking . . . . . . . . . . . . . . . . . . . . . . . .18
16
Protector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 Cutting Chain with Bolt Cutter . . . . . . . . . . . . . . . . . . . .18
17
Load Chain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 Exploded View, Control Station . . . . . . . . . . . . . . . . . . . .22
MAINTENANCE 18
Exploded View, Hoist . . . . . . . . . . . . . . . . . . . . . . . . .23-24
Exploded View, Series 635 Low Headroom Trolley . . . . .25
Hoist Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Electric Brake Adjustment . . . . . . . . . . . . . . . . . . . . . . .12
Exterior Finish . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Trouble Shooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Recommended Spare Parts . . . . . . . . . . . . . . . . . . . . . .12
Electrical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Wiring Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
2
any properly maintained hoist develops a performance prob-
GENERAL INFORMATION lem, due to a material or workmanship defect, as verified by
CM, repair or replacement of the unit will be made to the
original purchaser without charge. This repair/replacement
SPECIFICATIONS policy applies only to Valustar Hoists installed, maintained
and operated as outlined in this manual, and specifically
The Valustar Electric Chain Hoist is a highly versatile materials
excludes parts subject to normal wear, abuse, improper
handling device that can be used to lift loads that are within
installation, improper or inadequate maintenance, hostile
rated capacity. The mechanical features of these hoists
environmental effects and unauthorized repairs/modifications.
include an alloy steel lift wheel, overload device (Protector),
hardened steel chain guides, simple two stage gear reduc-
We reserve the right to change materials or design if, in our
tion, lifetime lubrication, forged steel hooks and lightweight
opinion, such changes will improve our product. Abuse,
aluminum frames. The electrical features include hoist-duty
repair by an unauthorized person, or use of non-CM replace-
motor, magnetic reversing contactor, rugged control station,
ment parts voids the guarantee and could lead to dangerous
heavy-duty motor brake and control transformer (3 phase
operation. For full Terms of Sale, see Sales Order
units). Hoists are supplied with a rigid upper hook suspension
Acknowledgement. Also, refer to the back cover for
as standard. Table 1 summarizes the hoist’s specifications.
Limitations of Warranties, Remedies and Damages, and
Indemnification and Safe Operation.
CM REPAIR/REPLACEMENT POLICY
All Columbus McKinnon (CM) Valustar Electric Chain Hoists
are inspected and performance tested prior to shipment. If
Table 1
ACCESSORIES
Series 635 Low Headroom Trolley
These are manual push type trolleys designed for use with
the Valustar Electric Chain Hoists, and a rigid lug suspension
is required to attach the hoist to the trolley (see Figure 1).
The trolley is adjustable to operate on a range of American
Standard beams as indicated in Table 1, and it will also
operate on flat flanged beams.
Figure 3. Rigid Lug Suspension
Chain Container
This accessory is used to hold the slack chain, and it is sup-
plied complete with mounting hardware and mounting
instructions. The chain container is recommended for those
applications where the slack chain would interfere with the
load. Chain containers can be furnished for units already in
use. When ordering, specify hoist model and lift.
Before installing the hoist, make sure that the power supply
to which it will be connected is the same as that shown on
the nameplate located on the side of the hoist.
Note: To assure extra long life and top performance,
be sure to follow the load chain lubricating instruc-
tions on Page 12.
Figure 2. Series 635 Motor Driven Trolley
L
should clear the hoist frame by not more than 1/4" on
Models WE and WH and 7/16" on Model WR.
3. Insert the screws through the adapter and engage the self- ! WARNING
Operating the trolley on a beam that has no rail stops may
locking nuts enclosed in the hoist. Screws will enter the
allow the trolley to fall off the end of beam.
nuts freely except for the last 1/4" of travel during which the
resistance of the nut locking collar will be encountered.
Install rail stops at each end of the beam on which the trolley
TO AVOID INJURY:
is to operate.
4. Securely tighten the screws to the recommended seating
torque specified in the table below, using a 12 point sock-
et which fits the head of the screw.
To attach the hoist to the trolley a lug suspension (Figure 3) is
Recommended required. The trolley and lug suspension are packed sepa-
Model No. Screw Size Seating Torque rately, and the hook suspension that is packed with the hoist
WB, WE, WF 3/8-16 UNC-3A 30-45 Lb. Ft. may be discarded. To install the lug suspension, follow the
and WH instructions for attaching the suspension on this page.
WJ, WL, 1/2-20 UNF-3A 40-80 Lb. Ft.
To adjust the trolley to fit the beam properly, proceed as follows:
L
and WR
1. Arrange the side frames, load bracket, spacer washers
and nuts on the suspension bolts according to Figure 7
! WARNING and Table 2. Do not assemble cotter pins to the bolts.
Using other than CM supplied high strength suspension
screws to attach the suspension adapter to the hoist may Note: special trolleys shown in chart require
cause the screws to break and allow the hoist and load to fall. special suspension bolts.
L
! WARNING
An excessively worn beam flange may fail and allow the trolley
to fall from the beam.
L
flange.
POWER SUPPLY AND ELECTRICAL
! WARNING CONNECTIONS
If CM’s washer spacing recommendations are not followed,
trolley may fall from beam.
All Hoists
The hoist should be connected to a branch circuit which
Measure the actual beam flange on which the trolley is to
TO AVOID INJURY:
complies with the requirements of the National Electrical
operate and use Table 2 to determine the arrangement of the
spacer washers for that flange width.
Code and applicable local codes.
8. Then with a capacity load on hoist, operate trolley over Before connecting the hoist to the power supply, check that
the entire length of runway or monorail system to be sure the power to be used agrees with that shown on the hoist
that the adjustment and operation is satisfactory. On sys- identification label. In addition, for a three phase, dual volt-
tems with curves, keep the rail edges at the curved sec- age unit, check the voltage shown on the tag attached to
tions lightly greased. power cord.
7
Table 2
1-TON CAPACITY 2-TON CAPACITY
Trolley Side Frame Spacing NO. OF SPACERS NO. OF SPACERS
FLANGE
A B C D A B C D
WIDTH
2-5/8 10 0 0 10
3 9 1 1 9
“X” 3-3/8 8 2 2 8 8 0 0 8
3-5/8 7 3 3 7 7 1 1 7
STANDARD 4 6 4 4 6 6 2 2 6
TROLLEYS 4-5/8 4 6 6 4 4 4 4 4
5 3 7 7 3 3 5 5 3
5-1/4 2 8 8 2 3 5 6 2
5-1/2 1 9 8 2 2 6 7 1
5-5/8 1 9 9 1 1 7 7 1
6 0 8 8 0
6 5 5 5 4
6-1/4 4 6 6 3 8 2 1 8
7 0 9 9 1 5 5 4 5
SPECIAL 7-1/8 5 5 5 4
A B C D TROLLEYS 7-1/4 4 6 5 4
7-7/8 2 8 8 1
8 1 9 8 1
Minimum Beam Radius 24" for all capacities. Dimension applies to minimum S-Beam and will vary with larger S-Beams.
Do not allow the hook block or the loose end block to contact
TO AVOID INJURY:
220-240 230
440-480 460 the bottom of the hoist.
3. If hook lowers, it is necessary to change direction by • Noisy hoist operations due to brake and/or contactor
interchanging the Red Lead and the Black Lead of the chattering.
hoist power cord at power supply. Under no circum- • Dimming of lights or slowing of motors connected to the
stances should the internal wiring of control station or same circuit.
hoist be changed to reverse hook direction. The wiring is
inspected and tested at the factory. • Heating of the hoist motor and other internal components,
as well as heating of the wires and connectors in the cir-
cuit feeding the hoists.
• Failure of the hoist to lift the load due to motor stalling.
• Blowing of fuses or tripping of circuit breakers.
8
To avoid these low voltage problems, the hoist must be con-
nected to an electrical power supply system that complies
with the National Electrical Code and applicable local codes.
OPERATING INSTRUCTIONS
This system must also be rated for a minimum of 20 amps
and it must have #14 AWG or larger wiring, a disconnecting GENERAL
means, overcurrent protection (slow blow fuses or inverse-time
The hoist is equipped with a Protector™ that is designed to
type circuit breakers) and provisions for grounding the hoist.
L
allow the intermediate gear to slip on an excessive overload.
An overload is indicated when the hoist will not raise the
load. Also, some clutching noise may be heard if the hoist is
! WARNING loaded beyond rated capacity. Should this occur, immediate-
Failure to properly ground the hoist presents the danger of
electric shock.
ly release the up control to stop the operation of the hoist.
±
At this point, the load should be reduced to the rated hoist
Permanently ground the hoist as instructed in this manual.
TO AVOID INJURY: capacity or the hoist should be replaced with one of the
proper capacity. When the excessive load is removed, nor-
mal hoist operation is automatically restored.
Low voltage can also be caused by using an undersize CAUTION: The Protector™ is susceptible to over-
extension cord to supply power to the hoist. The following heating and wear when slipped for extended peri-
chart should be used to determine the size wires in the ods. Under no circumstance should the clutch be
extension cord in order to minimize the voltage drop between allowed to slip for more than a few seconds.
the power source and the hoist.
Due to the above, the hoist is not recommended for use in
LENGTH OF SINGLE-PHASE THREE-PHASE any application where there is a possibility of adding to an
EXTENSION HOISTS HOISTS already suspended load to the point of overload. This
CORD MIN. WIRE SIZE MIN. WIRE SIZE includes dumbwaiter installation (refer to limitations dis-
Up to 50 feet #14 AWG #16 AWG cussed in Safety Precautions on Page ii), containers that are
80 feet #12 AWG #16 AWG loaded in mid-air, etc. Also, if the hoist is used at unusual
extremes of ambient temperatures, above 150°F. or below
120 feet #10 AWG #14 AWG
15°F., changes in lubricant properties may permit the hoist to
L
raise larger loads than under normal operating conditions
and present possibility of damage or injury.
! WARNING
Failure to provide a proper power supply system for the hoist
On single phase units, it is necessary to stop the hoist before
may cause hoist damage and offers the potential for a fire. changing direction. Therefore, when lowering a load, the
rocker in the control station must be released momentarily
Provide the hoist with a 20 amp. minimum, overcurrent pro-
TO AVOID INJURY:
before the up control is depressed to raise the load. If this
tected power supply system per the National Electrical Code
±
HOIST WITH LOW HEADROOM TROLLEY 11. Take up a slack load chain carefully and start load easily
to avoid shock and jerking of hoist load chain. If there is
This unit should be moved by pushing on the suspended any evidence of overloading, immediately lower the load
load or by pulling the empty hook. However, the unit can also and remove the excess load.
be moved by pulling on the control station since an internal
steel cable extends the length of the control cord and is 12. Do not allow the load to swing or twist while hoisting.
anchored to the hoist and to the control station.
L
chain is slack before taking up slack chain. maintenance program should be established to prolong the
useful life of the hoist and maintain its reliability and continued
safe use. The program should include periodic and frequent
! WARNING
Allowing the load to bear against the hook latch and/or hook
inspections with particular attention being paid to the lubrica-
tip can result in loss of load.
tion of the various components using the recommended lubri-
cants (see page 12).
Do not allow the load to bear against the hook latch and/or
TO AVOID INJURY:
Table 3
Minimum Frequent Inspections
Type of Service Item
Normal Heavy Severe
a) Brake for evidence of slippage.
b) Control functions for proper operation.
Yearly Weekly Daily c) Hooks for damage, cracks, twists, excessive throat opening, latch
to to
Weekly
engagement and latch operation – see page 11.
Yearly
d) Load chain for adequate lubrication, as well as for signs of wear,
damaged links or foreign matter – see page 11.
e) Load chain for proper reeving and twists.
Table 4
Minimum Periodic Inspections
Type of Service Item
Normal Heavy Severe
a) All items listed in Table 3 for frequent inspections.
b) External evidence of loose screws, bolts or nuts.
Yearly Every Every c) External external evidence of worn, corroded, cracked or distorted
Six Three hook block, suspension bolts, gears, bearings, loose end chain, stop
Months Months block, loose end block and pins, and dead end block and pin
(double reeved units).
d) External evidence of damage to hook retaining nut or collar and pin.
Also check the upper suspension adapter making sure it is fully seat-
ed in the hoist frame and retighten the screws to the recommended
seating torque (see page 4). If a condition of loose screws persists,
replace the self-locking nuts in the frame.
e) External evidence of damage or excessive wear of the liftwheel and
hook block sheave (double reeved units) chain pockets. Widening
and deepening of the pockets may cause the chain to lift-up in the
pocket and result in binding between liftwheel and chain guides or
between the sheave and hook block (double reeved units).
Also, check the chain guides for wear or burring where the chain
enters the hoist.
Severely worn or damaged parts should be replaced.
f) External evidence of excessive wear or brake parts and brake
adjustment – see page 12.
g) External evidence of pitting or any deterioration of contactor contacts.
h) Inspect the electrical cords and cables for damaged insulation.
i) Inspect trolley trackwheels for external wear on tread and flange,
and for wear on internal bearings surfaces as evidenced by a loose-
ness on the stud.
11
LATCH TYPE HOOK tion for nicks, gouges, twisted links, stretching and excessive
(Upper and Lower) wear. In particular, observe the bearing surface between
links, and if any of these conditions exist, the load chain must
TO MEASURE OPENING,
be replaced. Chain should be gaged throughout its entire
NI E
DEPRESS LATCH
NG
PE R
length and replaced if beyond serviceable limits.
O SU
AGAINST HOOK BODY
EA
M
AS SHOWN
To determine if load chain should be continued in service,
check gage lengths as indicated in Figure 10. Chain worn
beyond length indicated, nicked, gouged or twisted should
be replaced before returning hoist to service. Chain should
be clean, free of twists and pulled taut before measuring. In
cases where the wear is localized and not beyond service-
able limits, it is sometimes possible to reverse the load chain,
end for end, and allow a new section to take the wear.
Removal and installation of the load chain is covered in sub-
Models Replace Hook When Opening is sequent paragraphs.
Greater Than
To aid in gaging load chain wear. A chain gage can be
WB, WF 1-3/16 obtained from CM. This can be obtained by ordering chain
WE, WH, WJ & WL 1-5/16 gage Part No. 3191.
CAUTION: Before installing new load chain, the unit
WR 1-1/2
Figure 9. Hook Inspection
must be disassembled to allow inspection for dam-
age or wear and replacement, if required, of mating
Hook Inspection parts (liftwheel, chain guides, motor and gear hous-
Hooks damaged from chemicals, deformations or cracks, or ings).
that have more than a 10° twist from the hook’s unbent plane
or excessive opening or seat wear must be replaced. Also,
hooks that are opened and allow the latch to not engage the
tip, must be replaced. Any hook that is twisted or has exces-
sive throat opening indicates abuse or overloading of the
unit. Inspect other load sustaining parts for damage.
On latch type hooks, check to make sure that the latch is not
damaged or bent and that it operates properly with sufficient
spring pressure to keep the latch tightly against the tip of the
hook and allow the latch to spring back to the tip when
released. If the latch does not operate properly, it should be
replaced. See Figure 9 to determine when the hook must be
replaced.
Figure 10. Gaging Load Chain Wear
Protector™ Dia. of No. of Links Max. Gage Length
The Protector™ should operate for the normal life of the hoist Models Chain Stock to Gage Allowable
without service. The device has been lubricated and calibrat- Used Chain
ed at the factory for a specific model of hoist and is not WE, WB, 0.250" 19 14-13/16"
adjustable or interchangeable with other models. For proper WF & WH
overload protection be sure before installing a Protector™ WJ, WL, 0.312" 21 18-7/8"
that it is correct for the unit. The spring washer of the and WR
Protector™ has been color coded at the factory as follows:
When installing new load chain or mating parts, refer to
Models Protector™ Color Code Lubrication on page 12.
IMPORTANT: Do not use replaced chain for other
WB, WE White
L
use after disposal.
WL, WR Green
! WARNING
Removing the snap ring on the Protector™ assembly will
allow the parts to spring apart.
L
! WARNING
Using other than CM supplied load chain may cause the chain
to jam in the hoist and/or allow the chain to break and the load
Do not attempt to disassemble the Protector™. to drop.
TO AVOID INJURY:
L
When lubricating the chain, apply sufficient lubricant to obtain natural
L
run-off and full coverage.
! WARNING
The lubricants used in and recommended for the Valustar
Hoist may contain hazardous materials that mandate specific
handling and disposal procedures. ! WARNING
Used motor oils contain known carcinogenic materials.
Handle and dispose of lubricants only as directed in applica-
TO AVOID CONTACT AND CONTAMINATION:
ble material safety data sheets and in accordance with applica- Never use used motor oils as a chain lubricant. Only use
TO AVOID HEALTH PROBLEMS:
ble local, state and federal regulations. Lubriplate Bar and Chain Oil 10-R as a lubricant for the load
chain.
improper operation.
ken. A missing or broken shading coil will cause noisy brake
operation.
The gears and Protector™ are factory greased and should These symptoms indicate the need for parts replacement.
not need to be renewed unless the gears have been 4. Turn adjusting nuts clockwise gaging the air gap at both ends.
removed from the housing and degreased.
CAUTION: Never degrease or attempt to disassem-
5. Replace cover, reconnect the power and check operation.
TROUBLE SHOOTING
––– Probable Cause ––– ––– Remedy–––
1. Hook does not respond to control station.
A. No voltage at hoist – main line or branch circuit switch open; branch line fuse A. Close switch, replace fuse or reset breaker.
blown or circuit breaker tripped.
B. Phase failure (single-phasing, three-phase unit only) – open circuit, grounded or B. Correct power supply system. Check for electrical continuity and repair or replace
faulty connection in one line of supply system, hoist wiring, reversing contactor, defective part.
motor leads or windings.
C. Open control circuit – open or shorted winding in transformer or reversing C. Check electrical continuity and repair or replace defective part.
contactor coil; loose connection or broken wire in circuit; mechanical binding in
contactor; control station contacts not closing or opening
D. Wrong voltage or frequency. D. Use the voltage and frequency indicated on hoist identification label.
E. Low voltage. E. Correct low voltage condition as described on page 7.
F. Brake not releasing – open or shorted coil winding; armature binding. F. Check electrical continuity and connections. Check that correct coil has been
installed. The coil for three phase dual voltage unit operates at 230 volts when the
hoist is connected for either 230 volt or 460 volt operation. Check brake adjust-
ment (page 12).
G. Excessive load. G. Reduce load to the capacity limit of hoist as indicated on the hoist identification
label.
B. Failure of the motor cut-out switch to effect dynamic braking at time of reversal B. Check connections to switch. Replace damaged switch or faulty capacitor.
(single-phase units only).
C. Phase reversal (three-phase units only). C. Refer to installation instructions page 7.
8. Motor overheats.
A. Excessive load. A. See item 1G.
B. Low voltage. B. Correct low voltage condition as described on page 7.
C Extreme external heat. C. Above an ambient temperature of 104°F (40°C), the frequency of hoist operation
must be limited to avoid overheating the motor. Special provisions should be made
to ventilate the space or shield the hoist from radiant heat.
D. Frequent starting or reversing. D Avoid excessive inching, jogging or reversing. This type of operation drastically
shortens the motor and contactor life and causes excessive brake wear.
E. Phase failure or unbalanced current in the phases (three-phase units only). E. See item 1B.
F. Brake dragging. F. Check brake adjustment as described on page 12.
G. Motor cut-out device not opening start winding circuit (single-phase units only). G. See Item 3C.
ELECTRICAL DATA element and impose normal voltage) or D.C. resistance sub-
stantially below normal. The current method is recommended
To Detect Open and Short Circuits in for coils with very low D.C. resistance.
Electrical Components
Motor current draw in the stator should be measured with the
Open circuits in the coils of electrical components may be rotor in place and running. Brake, relay and contactor coil
detected by isolating the coil and checking for continuity with current should be measured with the core iron in operating
an ohmmeter or with the unit in series with a light or bell circuit. position.
Shorted turns are indicated by a current draw substantially
above normal (connect ammeter in series with suspected
Table 5
Electrical Data for Hoist Components
CONTACTOR
Models Coil Normal D.C. Resistance
Voltage (Volts) Current (Amps) (Ohms)*
TRANSFORMER WB, WE,
D.C. Resistance WF & WH 120 .04 297.5
Voltage Leads (Ohms)*
WJ, WL,
230/480 Secondary: and WR 120 .04 297.5
TO 115 Blue-tan to Blue 19.5
Primary: .
Red-black 87.5
to Red-blue
BRAKE COIL
Primary:
Rated Nominal Current D.C. Resistance
White-red to 99.0
Voltage (Amps) at Rated Voltage (Ohms)*
White-green
115 0.5 6.2
230** 0.25 24.7
MOTORS
Voltage Full Load *D.C.
Phase Current Resistance
Models & Hertz H.P. (Amps) Leads (Ohms)
WB, WE 115-1-60 1/4 4.6 5 TO 8 (START) 4.9
T1 to T2 4.3
T3 to T4 4.3
WB, WE 230/460 1/4 1.4/.70 1 to 4 14.8
3-60 2 to 5 14.8
3 to 6 14.8
7 to 8 29.5
7 to 9 29.5
8 to 9 29.5
WF, WH 115-1-60 1/2 7.2 5 to 8 (START) 3.7
T1 to T2 3.8
T3 to T4 3.8
WF, WH 230/460 1/2 1.8/.90 1 to 4 7.8
3-60 2 to 5 7.8
3 to 6 7.8
7 to 8 15.6
7 to 9 15.6
8 to 9 15.6
WL, WR 115-1-60 1 9.8 5 to 8 (START) 1.3
T1 to T2 1.1
T3 to T4 1.1
WJ, WL, WR 230/460 1 3/1.5 1 to 4 4.7
3-60 2 to 5 4.7
3 to 6 4.7
7 to 8 9.4
7 to 9 9.4
8 to 9 9.4
*Resistance values listed are nominal and they may vary slightly from component to component.
**On dual-voltage units connected for 460 volts, brake coils operate on 230 volts.
15
THREE PHASE
230/460-3-60
220/380-415-3-50
MODELS WB, WE, WF &
WH
THREE PHASE
230/460-3-60
220/380-415-3-50
MODELS WJ, WL & WR
Figure 11. Typical Wiring Diagrams. Wiring Diagrams shown are representative. Consult diagram in Hoist or furnished with unit.
16
To install the replacement mechanism, a press-on tool as shown
ASSEMBLY in Figure 13 will be required. The press-on tool is not included in
the kit, however, it may be ordered from CM – order centrifugal
mechanism press-on tool part number 28598.
HOOK OR LUG SUSPENSION
When installing the replacement centrifugal mechanism, the
Models WE, WH, and WR spacer is placed between the rotor shaft shoulder and the cen-
Assemble the dead end bolt and block through the suspen- trifugal mechanism as shown in Figure 13. Using a slow-acting
sion adapter, as shown in Figure 12. press, apply pressure to the press-on tool and press the mech-
anism onto the shaft until it sets against the spacer. To prevent
damaging the mechanism and/or spacer, the force applied to
the press-on tool press the mechanism onto the shaft should
not exceed 3000 pounds.
FASTENERS
Models WE, WB, WF and WH, tighten motor housing cover
screws (624-106) to where they have a minimum breakaway
torque of 48 pound inch.
L
using the drift and a hammer or slow acting press.
3. Using the following procedures (cutting chains) cut a por-
tion out of the second to last link (flat link) on the loose
! WARNING side of the old chain to form a coupling link. The portion
Use of improper lower hook chain block pin as well as improper removed should be centered on the weld and be 3/8"
installation of this pin can cause the pin to break and allow the
load to fall.
long. Remove any burrs from the cut edges of the cou-
pling link. Discard the last link.
L
LOAD CHAIN hook block using the old chain and coupling link. Be sure
there are no twists in the chain and the first link of the new
chain is a flat link.
NOTE: Upstanding links in the hook block will
! WARNING
Improper installation (reeving) of the load chain can result in a have weld towards the sheave.
dropped load. Remove the coupling link and remove the old chain from
Verify use of proper size and type of hoist load chain for
TO AVOID INJURY/DAMAGE: the dead end block at the hoist. Run the new chain up to
specific hoist.
the dead end block making sure there is no twist in the
chain between the hook block and dead end block.
Attach the last link (flat link) of the new chain to the dead
end block.
If the hoist is completely disassembled when the new chin is
to be installed, the new chain should be placed over the lift-
wheel (with weld on upstanding links away from liftwheel).
Leave 2-1/2' of chain hanging free on the loose end side.
Refer to steps 5 and 6 above to complete the installation.
Note: On the double chain units, it will be necessary
to use a length of soft wire to pull the new chain
through the hook block in lieu of using the coupling
link and old chain as indicated.
If the starter chain method is not used, the chain can be
Use only CM Star () Grade Load Chain and CM replacement parts. Use of
installed by partially disassembling the hoist. Remove the
other chain and parts may be dangerous and voids factory warranty.
loose-end chain, loose-end block and stop block from the
chain. Then, energize the hoist to carefully run the old chain
out of the hoist. Disconnect the hoist from the power supply
L
and remove the electric brake assembly. Rotate the brake
hub by hand, at the same time feeding the new chain into
! WARNING and through liftwheel area with the hoist upside down or using
Use of commercial or other manufacturers’ chain and parts to
a soft wire to pull the chain up onto the liftwheel. Be sure that
repair CM Hoists may cause load loss. the weld on the upstanding link is away from the liftwheel.
Refer to steps 5 and 6 above to complete the installation.
Use only CM supplied replacement load chain and parts. Chain
TO AVOID INJURY:
and parts may look alike, but CM chain and parts are made of NOTE: On the double reeved units, it will be neces-
specific material or processed to achieve specific properties. sary to use a length of soft wire to pull the new
chain through the hook block in lieu of using the
coupling link and old chain as indicated.
18
The following methods are recommended when cutting a *If the protector prevents lifting a load of 125% of rated
length of new chain from stock or cutting off worn chain. capacity, reduce load to rated capacity.
NOTE: For additional information on inspection and
testing, refer to Code B30.16 “Overhead Hoists”
obtainable from ASME Order Department, 22 Law
Drive, Box 2300, Fairfield, NJ 07007-2300, U.S.A.
Grinder
Nicks
REPLACEMENT PARTS
ORDERING INSTRUCTIONS
The following information must accompany all correspon-
Figure 14. Cutting Chain by nicking dence or orders for replacement parts:
1. Use a grinder and nick the link on both sides (Figure 14), 1. Hoist Model Number from identification label.
then secure the link in a vise and break off with a hammer.
2. Serial number of the hoist stamped below identification
2. Use a 7" minimum diameter by 1/8" thick abrasive wheel plate.
(or type recommended by wheel supplier) that will clear
adjacent links. 3. Voltage, Phase, Hertz from identification label.
4. Length of lift.
5. Key number of part from parts list.
6. Number of parts required.
7. Part name from parts list.
8. Part number from the parts lists.
If trolley replacement parts are ordered, also include the type
and capacity of the trolley.
NOTE: When ordering replacement parts, it is recom-
mended that consideration be given to the need for
also ordering such items as gaskets, fasteners, insula-
Figure 15. Cutting Chain with a bolt cutter tors, etc. These items may be damaged or lost during
disassembly or just unfit for future use because of
deterioration from age or service.
3. Use a bolt cutter (Figure 15) similar to the H.K. Porter
L
No. 0590MTC with special cutter jaws for cutting hard-
L
ened chain (1" long cutting edge).
! WARNING
! WARNING
Using “commercial” or other manufacturer’s parts to repair
Cutting chain can produce flying particles.
the CM Valustar Hoist may cause load loss.
Wear eye protection. Provide a shield over chain to prevent
TO AVOID INJURY:
flying particles. Use only CM supplied replacement parts. Parts may look alike,
TO AVOID INJURY:
PARTS LIST
NUMBER REQUIRED PART NUMBERS
KEY
PART NAME Models WB, Models WJ, Model Model Model Model Model Model Model
NO.
WE, WF, WH WL, WR WB WE WF WH WJ WL WR
624-100 Motor Housing 1 1 27028 24008
28669 35620
624-101 Gear Housing 1 1
(Includes Item 624-102) (Includes Items 624-102, 624-120, 624-129)
Intermediate Gear and Pinion
Order 83670 (Bearing)
624-102 Bearing - Inboard 1 1 88440
and 24350 (Shaft Adapter)
(Includes Shaft Adapter for WJ, WL, WR)
624-103 Chain Guide 2 2 27008 35018
624-104 Liftwheel 1 1 27360 35421
624-105 Suspension Adapter Nut 2 2 927755 935791
Motor Housing Cover Screw
624-106 2 2 C302 C303
and Lockwasher
624-107 Liftwheel Gear Retainer Ring 1 --- 27767 ---
Motor Shaft Bearing, Inboard
624-108 2 2 27790 35764
Retainer Ring
Gear Housing Attaching Screw Order 28830 Screw Order 982682 Screw
624-109 4 4
and Lockwasher and 940802 Lockwasher and 940830 Lockwasher
Loose End Screw, Washer
624-110 1 1 C304 C305
and Lockwasher
624-111 Motor Shaft Bearing - Outboard 1 --- 82009 ---
624-112 Motor Shaft Bearing - Inboard 1 1 82003 82004
624-113 Stator Pin 1 --- 983541 ---
Control Cable Screw, Washer
624-114 1 1 C306 C306
and Lockwasher
Back Frame Assembly 24620
624-115 1 1 24622
(Includes Brake Studs) (Includes 624-116 thru 624-118, 624-127, 624-128)
624-116 Drive Shaft and Pinion Bearing 1 1 82009 83691
Intermediate Gear and Pinion
624-117 1 1 82009 88437
Bearing - Outboard
Bearing Retainer Screw
624-118 1 2 C307 C308
and Washers
Back Frame Attaching Screw Order 982699 Screw Order 982682 Screw
624-119 3 4
and Lockwasher and 940802 Lockwasher and 940830 Lockwasher
624-120 Liftwheel Bearing - Gear End 1 1 88429 82002
624-121 Motor Housing Cover 1 1 24504 24759
624-122 Back Frame Cover 1 1 24757 24758
Back Frame Cover Attaching Screw
624-123 2 2 C309 C310
and Lockwasher
624-125 Hoist I.D. Label 115-1-60, 230/460 1 1 Contact Factory Contact Factory
624-126 Capacity/Warning Label 1 1 24764 24765 24765 24766 24765 24766 24768
624-127 Hole Plug Set 4 1 982454 C311
624-128 Back Frame Expansion Plug 1 --- 940837 ---
624-129 Gear Housing Plug --- 1 --- 935767
Drive Shaft and Pinion Assembly
(Includes Items 624-131 thru 624-133 for Order 624-116, 624-131,
624-130 Models WB, WE, WF, WH, WJ, WL and WR. 1 1 24639 24638 24638
Also Includes Item 624-116 with Models
624-132 and 624-133
WJ, WL, WR
24641 24642 35357 35356 35356
624-131 Drive Shaft and Pinion Assembly 1 1
(8T. Pinion, 5-15/64” Long) (8T Pinion, 5 43/64” Long) (18T.) (12T.) (12T.)
27851 27852 24019 24019
624-132 Brake Hub 1 1 ---
(8T. 21/32” Long) (8T. 1-1/8” Long) (13T.) (13T.)
624-133 Brake Hub Retainer Ring 1 1 27766 35766
624-134 Liftwheel Gear 1 1 27009 (53T.) 35009 (79T.)
624-135 Intermediate Pinion 1 1 24351 (8T.) 35351 (10T.)
624-136 Intermediate Gear Retainer Ring 1 1 27765 35763
624-137 Protector 1 1 28694 28695 36668 36670 36670
624-138 Liftwheel Bearing - Motor End 1 1 88429 83669
624-139 Liftwheel Gear Nut and Lockwasher --- 1 --- C312
20
PARTS LIST
MODELS AND VOLTAGES
No.
Key No. Part Name WB, WE WF, WH WJ WL WR
Req’d
115-1-60 230/460 115-1-60 230/460 115-1-60 230/460 115-1-60 230/460 115-1-60 230/460
624-199 Brake Coil 1 51001 51003 51001 51003 --- 51002 51001 51002 51001 51002
624-210 Rotor Assembly 1 24228 286004 24226 286000 --- --- --- --- --- ---
includes items 624-108
and 624-112
115-1-60
includes 624-212
624-211 Stator (also order 624-113 1 24222 24221 24223 24220 --- 24225 367001 24225 367001 24225
for models WB, WE, WF, WH
CONTROL STATION
Key No. Part Name No. Req’d Part No. 624-231
624-303
624-822
624-307
624-304
624-252
624-164
624-163 624-166
624-162 624-165
®
SERIES 635 LOW HEADROOM TROLLEY PARTS LIST
Note: When ordering parts, always furnish hoist model and serial number, motor horsepower,
voltage, phase, frequency and rated capacity of hoist on which the parts are to be used.
For the location of the nearest CM Master Parts Depot, see the list located on the inside front cover.
THE WARRANTY STATED BELOW IS GIVEN IN PLACE OF ALL the use of the goods if, prior to such damage, injury or loss, such
OTHER WARRANTIES, EXPRESS OR IMPLIED, OF MER- goods are (1) damaged or misused following Seller’s delivery to car-
CHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR rier; (2) not maintained, inspected, or used in compliance with
OTHERWISE, NO PROMISE OR AFFIRMATION OF FACT MADE applicable law and Seller’s written instructions and recommenda-
BY ANY AGENT OR REPRESENTATIVE OF SELLER SHALL tions; or (3) installed, repaired, altered or modified without compli-
CONSTITUTE A WARRANTY BY SELLER OR GIVE RISE TO ance with such law, instructions or recommendations.
ANY LIABILITY OR OBLIGATION. UNDER NO CIRCUMSTANCES SHALL SELLER BE LIABLE FOR
INCIDENTAL OR CONSEQUENTIAL DAMAGES AS THOSE
Seller warrants that on the date of delivery to carrier the goods are TERMS ARE DEFINED IN SECTION 2-715 OF THE UNIFORM
free from defects in workmanship and materials. COMMERCIAL CODE.
SELLER’S SOLE OBLIGATION IN THE EVENT OF BREACH OF INDEMNIFICATION AND SAFE OPERATION
WARRANTY OR CONTRACT OR FOR NEGLIGENCE OR Buyer shall comply with and require its employees to comply with
OTHERWISE WITH RESPECT TO GOODS SOLD SHALL BE directions set forth in instructions and manuals furnished by Seller
EXCLUSIVELY LIMITED TO REPAIR OR REPLACEMENT, F.O.B. and shall use and require its employees to follow such instructions
SELLER’S POINT OF SHIPMENT, OF ANY PARTS WHICH SELL- and manuals and to use reasonable care in the use and mainte-
ER DETERMINES TO HAVE BEEN DEFECTIVE or if Seller deter- nance of the goods. Buyer shall not remove or permit anyone to
Figure 18. Series 635 Low Headroom Trolley Exploded View
mines that such repair or replacement is not feasible, to a refund of remove any warning or instruction signs on the goods. In the event
the purchase price upon return of the goods to Seller. of personal injury or damage to property or business arising from
Key No. Part Name No. Req’d. Part No. Key No. Part Name No. Req’d. Part No. the use of the goods, Buyer shall within 48 hours thereafter give
Any action against Seller for breach of warranty, negligence or oth- Seller written notice of such injury or damage. Buyer shall cooperate
1-Ton 2-Ton 1-Ton 2-Ton 1-Ton 2-Ton 1-Ton 2-Ton
624-400 Trackwheel 4 4 35774 50762 624-409 Load Bracket erwise, must be commenced within one year after such cause of with Seller in investigating any such injury or damage and in the
624-401 Trackwheel Stud 4 4 987790 35838 action occurs. defense of any claims arising therefrom.
3-7/16" wide* 1 1 35019 –
624-402 Trackwheel Stud Nut 4 4 982520 948804 5-13/32" wide** 1 1 35024 – NO CLAIM AGAINST SELLER FOR ANY DEFECT IN THE GOODS If Buyer fails to comply with this section or if any injury or damage is
624-403 Suspension Bolt 4-3/16" wide† 1 1 – 35033 SHALL BE VALID OR ENFORCEABLE UNLESS BUYER’S WRIT- caused, in whole or in part, by Buyer’s failure to comply with applic-
(Special Alloy Steel Bolt) TEN NOTICE THEREOF IS RECEIVED BY SELLER WITHIN ONE able federal or state safety requirements, Buyer shall indemnify and
YEAR FROM THE DATE OF SHIPMENT. hold Seller harmless against any claims, loss or expense for injury
6-11/16" wide†† 1 1 – 35043
Seller shall not be liable for any damage, injury or loss arising out of or damage arising from the use of the goods.
9-5/32" long* 2 – 35450 –
624-410 Vertical Load Bar Pin
10-1/4" long** 2 – 35407 – (Special Alloy Steel Pin)
10" long† – 2 – 35445 2-11/16" long* 1 1 35371 –
12-1/16" long ††
– 2 – 35414 2-7/8" long** 1 1 – 35413
L
624-404 Trolley Spacer Washers 3-3/4" long† 1 1 – 35400
0.165" thick* 40 – 35782 – 624-411 Vertical Load Bar Pin Screw
0.125" thick** 38 – 958822 – 1/2" long* 1 1 982383 – ! WARNING
Alterations or modifications of equipment and use of non-
factory repair parts can lead to dangerous operation and
0.165" thick †
– 32 – 35783 1-1/4" long** 1 1 982386 –
0.125" thick†† – 38 – 988039 3/4" long† 1 1 – 982433 injury.
®
Without Trolley Guards*** 2 2 35640 35654 624-414 Identification Label 1 1 36916 36917
Trolley Guards*** 2 2 35635 35636 624-416 Trackwheel Washer – 1 – 987903
624-408 Side Frame, ID Plate Side 624-417 Warning Label 1 1 936984 936984
Columbus McKinnon Corporation
Industrial Products Division
Without Trolley Guards*** 2 2 35640 35654
Fax 716-689-5644
flange widths. flange widths.
** These items are for the 1-Ton Trolley for operation on over 5.64" thru 7.00" ††
These items are for the 2-Ton Trolley for operation on over 6.00" thru 8.25"
flange widths. flange widths.
© 2011 Columbus McKinnon Corp. Printed in USA
*** If side frame is equipped with spacer block, contact factory.