Design and Operating Notes

Lubricants
6

6 Design and Operating Notes 1

6.1 Lubricants
2
General informa- Unless a special arrangement is made, SEW-EURODRIVE supplies the drives with a
tion lubricant fill adapted for the specific gear unit and mounting position. The decisive factor
is the mounting position (M1 ... M6, → Sec. "Mounting Positions and Important Order 3
Information") specified when ordering the drive. You must adapt the lubricant fill in case
of any subsequent changes made to the mounting position (→ Lubricant fill quantities). 4

Lubricant table The lubricant table on the following page shows the permitted lubricants for SEW-EU- 7
RODRIVE gear units. Please note the following key to the lubricant table.
Key to the lubricant Abbreviations used, meaning of shading and notes: 8
table CLP = Mineral oil
CLP PG = Polyglycol (W gear units, conforms to USDA-H1)
9
CLP HC = Synthetic hydrocarbons
E = Ester oil (water pollution danger category WGK 1)
HCE = Synthetic hydrocarbons + ester oil (USDA - H1 certification) 10
HLP = Hydraulic oil 6
= Synthetic lubricant (= synthetic anti-friction bearing grease)
11
= Mineral lubricant (= mineral-based anti-friction bearing grease)
1) Helical-worm gear units with PG oil: Please contact SEW-EURODRIVE
2) Special lubricant for Spiroplan® gear units only 12
3) Recommendation: Select SEW fB ≥ 1.2
4) Pay attention to critical starting behavior at low temperatures!
13
5) Low-viscosity grease
6) Ambient temperature

Lubricant for the food industry (food grade oil)

14

Oil
Oil
Biodegradable oil (lubricant for use in agriculture, forestry and water resources) 15

Anti-friction bear- The anti-friction bearings in gear units and motors are given a factory-fill with the greas- 16
ing greases es listed below. SEW-EURODRIVE recommends that you regrease anti-friction bear-
ings with a grease fill at the same time as changing the oil. 17
Ambient temperature Manufacturer Type
-20 °C ... +60 °C Mobil Mobilux EP 2
Anti-friction bearing in
gear unit
18
-40°C ... +80°C Mobil Mobiltemp SHC 100
-20°C ... +80°C Esso Unirex EQ3
Anti-friction bearing in -20°C ... +60°C Shell Alvania RL3 19
motor +80°C ... +100°C Klüber Barrierta L55/2
-45°C ... -25°C Shell Aero Shell Grease 161
20
Special greases for anti-friction bearings in gear units:

-30°C ... +40°C Aral Aral Eural Grease EP 2

21
-20°C ... +40°C Aral Aral Aralube BAB EP2
Oil
Oil

1 Recommended for continuous operation at ambient temperatures below 0°C, for example in a cold sto-
22
rage.

The following grease quantities are required:

• For fast-running bearings (motor and gear unit input end): Fill the cavities between
the rolling elements one third full with grease.
• For slow-running bearings (in gear units and at gear unit output end): Fill the cavities
between the rolling elements two thirds full with grease.

Catalog – GM2004 71
 6

72
6)
Oil ISO,NLGI Mobil®
°C -50 0 +50 +100 DIN (ISO)
Standard Mobilgear Shell Omala Klüberoil Aral Degol BP Energol Tribol Optigear Renolin
R... -10 +40 CLP(CC) VG 220 Meropa 220
630 220 GEM 1-220 BG 220 GR-XP 220 1100/220 BM 220 CLP 220
Lubricant table

Mobil Shell Tivela Klübersynth Aral Degol BP Enersyn Tribol Synlube Optiflex A
-25 +80 CLP PG VG 220
Glygolyle 30 WB GH 6-220 GS 220 SG-XP 220 800/220 CLP 220 220
4) Mobil Shell Omala Klübersynth Aral Degol Tribol Pinnacle Optigear Syn- Renolin Unisyn
-40 +80 VG 220 thetic A 220 CLP 220
SHC 630 220 HD EG 4-220 PAS 220 1510/220 EP 220
K...(HK...) CLP HC
4) -40 +40 Mobil Klübersynth Pinnacle
VG 150
SHC 629 EG 4-150 EP 150
Lubricants

-20 CLP (CC) VG 150 Mobilgear Shell Omala Klüberoil Aral Degol BP Energol Tribol Optigear Renolin
+25 Meropa 150
VG 100 627 100 GEM 1-150 BG 100 GR-XP 100 1100/100 BM 100 CLP 150
VG 68-46 Mobil Shell Tellus Klüberoil Aral Degol Tribol Rando EP Optigear Renolin
F... -30 +10 HLP (HM)
VG 32 D.T.E. 13M T 32 GEM 1-68 BG 46 1100/68 Ashless 46 32 B 46 HVI
4) Mobil Klüber-Summit Cetus
-40 +10 CLP HC VG 32 HySyn FG-32
SHC 624 PAO 46
4) -40
VG 22 Mobil Shell Tellus Isoflex BP Energol Rando
-20 HLP (HM)
VG 15 D.T.E. 11M T 15 MT 30 ROT HLP-HM 10 HDZ 15
Standard Mobilgear Shell Omala Klüberoil Aral Degol BP Energol Tribol Optigear Renolin
0 +40 CLP (CC) VG 680 Meropa 680
636 680 GEM 1-680 BG 680 GR-XP 680 1100/680 BM 680 CLP 680
1) Mobil Glygoyle Klübersynth BP Enersyn Tribol Synlube
-20 +60 CLP PG VG 680
Design and Operating Notes

HE 680 GH 6-680 SG-XP 680 800/680 CLP 680

S...(HS...) 4) Mobil Shell Omala Klübersynth Pinnacle
-30 +80 VG 460
SHC 634 460 HD EG 4-460 EP 460
CLP HC
4) Mobil Klübersynth Pinnacle
-40 +10 VG 150
SHC 629 EG 4-150 EP 150
VG 150 Mobilgear Shell Omala Klüberoil Aral Degol BP Energol Tribol Optigear Renolin
-20 +10 CLP (CC) Meropa 100
VG 100 627 100 GEM 1-150 BG 100 GR-XP 100 1100/100 BM 100 CLP 150
1) Mobil Klübersynth Tribol Synlube Optiflex A
-25 +20 CLP PG VG 220
Glygoyle 30 GH 6-220 800/220 CLP 220 220
4) Mobil Klüber-Summit Cetus
-40 0 CLP HC VG 32 HySyn FG-32
SHC 624 PAO 46
4) Shell Cassida Klüberoil Aral Eural Optileb
-30 +40 HCE VG 460
R...,K...(HK...), Fluid GL 460 4UH1-460 Gear 460 GT 460
F...,S...(HS...) -20 +40
Klüberbio Aral Degol Optisynt
E VG 460
Oil CA2-460 BAB 460 BS 460
Standard 2) Klüber SEW
W...(HW...) -20 +40 SEW PG VG 460
HT-460-5
4) -40 +10 API GL5
SAE 75W90 Mobilube SHC
(~VG 100) 75 W90-LS
3) Klübersynth
-20 +40 CLP PG VG 460
UH1 6-460
Glygoyle Shell Tivela Klübersynth Multifak
R32 -25 +60 00 Grease 00 GL 00 GE 46-1200 6833 EP 00
DIN 51 818
R302 Standard Mobilux Shell Alvania Aralub BP Energrease Multifak Longtime Renolin
-15 +40 5) 000 - 0 GL 00 LS-EP 00
EP 004 MFL 00 EP 000 PD 00 SF 7 - 041
01 805 792

Catalog – GM2004
 Design and Operating Notes
Lubricants
6

Lubricant fill The specified fill quantities are recommended values. The precise values vary depend- 1
quantities ing on the number of stages and gear ratio. When filling, it is essential to check the oil
level plug since it indicates the precise oil capacity.
2
The following tables show guide values for lubricant fill quantities in relation to the
mounting position M1 ... M6.
3
Helical (R-) gear RX..
units
4
Fill quantity in liters
Gear unit
M1 M2 M3 M4 M5 M6
RX57 0.60 0.80 1.30 1.30 0.90 0.90 7
RX67 0.80 0.80 1.70 1.90 1.10 1.10
RX77 1.10 1.50 2.60 2.70 1.60 1.60 8
RX87 1.70 2.50 4.80 4.80 2.90 2.90
RX97 2.10 3.40 7.4 7.0 4.80 4.80
RX107 3.90 5.6 11.6 11.9 7.7 7.7 9

RXF..
10
6
Fill quantity in liters
Gear unit
M1 M2 M3 M4 M5 M6 11
RXF57 0.50 0.80 1.10 1.10 0.70 0.70
RXF67 0.70 0.80 1.50 1.40 1.00 1.00 12
RXF77 0.90 1.30 2.40 2.00 1.60 1.60
RXF87 1.60 1.95 4.90 3.95 2.90 2.90
RXF97 2.10 3.70 7.1 6.3 4.80 4.80 13
RXF107 3.10 5.7 11.2 9.3 7.2 7.2
14
R.., R..F
Fill quantity in liters 15
Gear unit
M11 M21 M3 M4 M5 M6
R07 0.12 0.20 0.20 0.20 0.20 0.20 16
R17 0.25 0.55 0.35 0.55 0.35 0.35
R27 0.25/0.40 0.70 0.50 0.70 0.50 0.50
R37 0.30/0.95 0.85 0.95 1.05 0.75 0.95 17
R47 0.70/1.50 1.60 1.50 1.65 1.50 1.50
R57 0.80/1.70 1.90 1.70 2.10 1.70 1.70 18
R67 1.10/2.30 2.60/3.50 2.80 3.20 1.80 2.00
R77 1.20/3.00 3.80/4.10 3.60 4.10 2.50 3.40
R87 2.30/6.0 6.7/8.2 7.2 7.7 6.3 6.5 19
R97 4.60/9.8 11.7/14.0 11.7 13.4 11.3 11.7
R107 6.0/13.7 16.3 16.9 19.2 13.2 15.9 20
R137 10.0/25.0 28.0 29.5 31.5 25.0 25.0
R147 15.4/40.0 46.5 48.0 52.0 39.5 41.0
R167 27.0/70.0 82.0 78.0 88.0 66.0 69.0 21
1 The larger gear unit of multi-stage gear units must be filled with the larger oil volume.
22

RF..
Fill quantity in liters
Gear unit
M11 M21 M3 M4 M5 M6
RF07 0.12 0.20 0.20 0.20 0.20 0.20
RF17 0.25 0.55 0.35 0.55 0.35 0.35
RF27 0.25/0.40 0.70 0.50 0.70 0.50 0.50
RF37 0.35/0.95 0.90 0.95 1.05 0.75 0.95

Catalog – GM2004 73
 Design and Operating Notes
6 Lubricants

Fill quantity in liters

Gear unit
M11 M21 M3 M4 M5 M6
RF47 0.65/1.50 1.60 1.50 1.65 1.50 1.50
RF57 0.80/1.70 1.80 1.70 2.00 1.70 1.70
RF67 1.20/2.50 2.70/3.60 2.70 2.60 1.90 2.10
RF77 1.20/2.60 3.80/4.10 3.30 4.10 2.40 3.00
RF87 2.40/6.0 6.8/7.9 7.1 7.7 6.3 6.4
RF97 5.1/10.2 11.9/14.0 11.2 14.0 11.2 11.8
RF107 6.3/14.9 15.9 17.0 19.2 13.1 15.9
RF137 9.5/25.0 27.0 29.0 32.5 25.0 25.0
RF147 16.4/42.0 47.0 48.0 52.0 42.0 42.0
RF167 26.0/70.0 82.0 78.0 88.0 65.0 71.0
1 The larger gear unit of multi-stage gear units must be filled with the larger oil volume.

Parallel shaft heli- F.., FA..B, FH..B, FV..B

cal (F-) gear units Fill quantity in liters
Gear unit
M1 M2 M3 M4 M5 M6
F..27 0.60 0.80 0.65 0.70 0.60 0.60
F..37 0.95 1.25 0.70 1.25 1.00 1.10
F..47 1.50 1.80 1.10 1.90 1.50 1.70
F..57 2.60 3.50 2.10 3.50 2.80 2.90
F..67 2.70 3.80 1.90 3.80 2.90 3.20
F..77 5.9 7.3 4.30 8.0 6.0 6.3
F..87 10.8 13.0 7.7 13.8 10.8 11.0
F..97 18.5 22.5 12.6 25.2 18.5 20.0
F..107 24.5 32.0 19.5 37.5 27.0 27.0
F..127 40.5 54.5 34.0 61.0 46.3 47.0
F..157 69.0 104.0 63.0 105.0 86.0 78.0

FF..
Fill quantity in liters
Gear unit
M1 M2 M3 M4 M5 M6
FF27 0.60 0.80 0.65 0.70 0.60 0.60
FF37 1.00 1.25 0.70 1.30 1.00 1.10
FF47 1.60 1.85 1.10 1.90 1.50 1.70
FF57 2.80 3.50 2.10 3.70 2.90 3.00
FF67 2.70 3.80 1.90 3.80 2.90 3.20
FF77 5.9 7.3 4.30 8.1 6.0 6.3
FF87 10.8 13.2 7.8 14.1 11.0 11.2
FF97 19.0 22.5 12.6 25.6 18.9 20.5
FF107 25.5 32.0 19.5 38.5 27.5 28.0
FF127 41.5 55.5 34.0 63.0 46.3 49.0
FF157 72.0 105.0 64.0 106.0 87.0 79.0

FA.., FH.., FV.., FAF.., FAZ.., FHF.., FHZ.., FVF.., FVZ.., FT..
Fill quantity in liters
Gear unit
M1 M2 M3 M4 M5 M6
F..27 0.60 0.80 0.65 0.70 0.60 0.60
F..37 0.95 1.25 0.70 1.25 1.00 1.10
F..47 1.50 1.80 1.10 1.90 1.50 1.70
F..57 2.70 3.50 2.10 3.40 2.90 3.00
F..67 2.70 3.80 1.90 3.80 2.90 3.20

74 Catalog – GM2004
 Design and Operating Notes
Lubricants
6

Gear unit
Fill quantity in liters 1
M1 M2 M3 M4 M5 M6
F..77 5.9 7.3 4.30 8.0 6.0 6.3
F..87 10.8 13.0 7.7 13.8 10.8 11.0
2
F..97 18.5 22.5 12.6 25.2 18.5 20.0
F..107 24.5 32.0 19.5 37.5 27.0 27.0 3
F..127 39.0 54.5 34.0 61.0 45.0 46.5
F..157 68.0 103.0 62.0 104.0 85.0 77.0
4
Helical-bevel (K-) K.., KA..B, KH..B, KV..B
gear units 7
Fill quantity in liters
Gear unit
M1 M2 M3 M4 M5 M6
K..37 0.50 1.00 1.00 1.25 0.95 0.95 8
K..47 0.80 1.30 1.50 2.00 1.60 1.60
K..57 1.20 2.30 2.50 2.80 2.60 2.40
9
K..67 1.10 2.40 2.60 3.45 2.60 2.60
K..77 2.20 4.10 4.40 5.8 4.20 4.40
K..87 3.70 8.0 8.7 10.9 8.0 8.0 10
K..97 7.0 14.0 15.7 20.0 15.7 15.5 6
K..107 10.0 21.0 25.5 33.5 24.0 24.0
11
K..127 21.0 41.5 44.0 54.0 40.0 41.0
K..157 31.0 62.0 65.0 90.0 58.0 62.0
K..167 33.0 95.0 105.0 123.0 85.0 84.0 12
K..187 53.0 152.0 167.0 200 143.0 143.0

13
KF..
Fill quantity in liters 14
Gear unit
M1 M2 M3 M4 M5 M6
KF37 0.50 1.10 1.10 1.50 1.00 1.00
15
KF47 0.80 1.30 1.70 2.20 1.60 1.60
KF57 1.30 2.30 2.70 3.15 2.90 2.70
KF67 1.10 2.40 2.80 3.70 2.70 2.70 16
KF77 2.10 4.10 4.40 5.9 4.50 4.50
KF87 3.70 8.2 9.0 11.9 8.4 8.4
17
KF97 7.0 14.7 17.3 21.5 15.7 16.5
KF107 10.0 21.8 25.8 35.1 25.2 25.2
KF127 21.0 41.5 46.0 55.0 41.0 41.0 18
KF157 31.0 66.0 69.0 92.0 62.0 62.0

19
KA.., KH.., KV.., KAF.., KHF.., KVF.., KAZ.., KHZ.., KVZ.., KT..
Fill quantity in liters 20
Gear unit
M1 M2 M3 M4 M5 M6
K..37 0.50 1.00 1.00 1.40 1.00 1.00
21
K..47 0.80 1.30 1.60 2.15 1.60 1.60
K..57 1.30 2.30 2.70 3.15 2.90 2.70
K..67 1.10 2.40 2.70 3.70 2.60 2.60 22
K..77 2.10 4.10 4.60 5.9 4.40 4.40
K..87 3.70 8.2 8.8 11.1 8.0 8.0
K..97 7.0 14.7 15.7 20.0 15.7 15.7
K..107 10.0 20.5 24.0 32.4 24.0 24.0
K..127 21.0 41.5 43.0 52.0 40.0 40.0
K..157 31.0 66.0 67.0 87.0 62.0 62.0
K..167 33.0 95.0 105.0 123.0 85.0 84.0
K..187 53.0 152.0 167.0 200 143.0 143.0

Catalog – GM2004 75
 Design and Operating Notes
6 Lubricants

Spiroplan® (W-) The fill quantity of Spiroplan® gear units does not vary, regardless of the mounting posi-
gear units tion.
Fill quantity in liters
Gear unit
M1 M2 M3 M4 M5 M6
W..10 0.16
W..20 0.26
W..30 0.50

Helical-worm (S-) S..

gear units Fill quantity in liters
Gear unit
M1 M2 M31 M4 M5 M6
S..37 0.25 0.40 0.50 0.55 0.40 0.40
S..47 0.35 0.80 0.70/0.90 1.00 0.80 0.80
S..57 0.50 1.20 1.00/1.20 1.45 1.30 1.30
S..67 1.00 2.00 2.20/3.10 3.10 2.60 2.60
S..77 1.90 4.20 3.70/5.4 5.9 4.40 4.40
S..87 3.30 8.1 6.9/10.4 11.3 8.4 8.4
S..97 6.8 15.0 13.4/18.0 21.8 17.0 17.0
1 The larger gear unit of multi-stage gear units must be filled with the larger oil volume.

SF..
Fill quantity in liters
Gear unit
M1 M2 M31 M4 M5 M6
SF37 0.25 0.40 0.50 0.55 0.40 0.40
SF47 0.40 0.90 0.90/1.05 1.05 1.00 1.00
SF57 0.50 1.20 1.00/1.50 1.55 1.40 1.40
SF67 1.00 2.20 2.30/3.00 3.20 2.70 2.70
SF77 1.90 4.10 3.90/5.8 6.5 4.90 4.90
SF87 3.80 8.0 7.1/10.1 12.0 9.1 9.1
SF97 7.4 15.0 13.8/18.8 22.6 18.0 18.0
1 The larger gear unit of multi-stage gear units must be filled with the larger oil volume.

SA.., SH.., SAF.., SHZ.., SAZ.., SHF.., ST..

Fill quantity in liters
Gear unit
M1 M2 M31 M4 M5 M6
S..37 0.25 0.40 0.50 0.50 0.40 0.40
S..47 0.40 0.80 0.70/0.90 1.00 0.80 0.80
S..57 0.50 1.10 1.00/1.50 1.50 1.20 1.20
S..67 1.00 2.00 1.80/2.60 2.90 2.50 2.50
S..77 1.80 3.90 3.60/5.0 5.8 4.50 4.50
S..87 3.80 7.4 6.0/8.7 10.8 8.0 8.0
S..97 7.0 14.0 11.4/16.0 20.5 15.7 15.7
1 The larger gear unit of multi-stage gear units must be filled with the larger oil volume.

76 Catalog – GM2004
 Design and Operating Notes
Installation/removal of gear units with hollow shafts and keys
6

6.2 Installation/removal of gear units with hollow shafts and keys 1

• Always use the supplied NOCO® fluid for installation. The fluid prevents contact cor-
rosion and facilitates subsequent removal. 2
• The key dimension X is defined by the customer, however X must be > DK.
3

Installation SEW-EURODRIVE recommends two variants for installation of gear units with hollow 4
shaft and key onto the input shaft of the driven machine (= customer shaft):
1. Use the supplied fastening parts for installation. 7
2. Use the optional installation/removal kit for installation.
8
1. Supplied fas- The following fastening parts are supplied as standard:
tening parts • Retaining screw with washer (2) 9
• Circlip (3)
10
6
Customer shaft • The installation length of the customer shaft with contact shoulder (A) must be L8 -
1 mm. 11
• The installation length of the customer shaft without contact shoulder (B) must equal
L8. 12
[A] [B]
13

14
[1] [4] [3] [2] [1] [4] [3] [2]

15
Figure 14: Customer shaft with contact shoulder (A) and without contact shoulder (B)

(1) Hollow shaft (3) Circlip

16
(2) Retaining screw with washer (4) Customer shaft

17
Dimensions and The retaining screw (2) must be tightened to the tightening torque MS given in the fol-
tightening torque lowing table.
18
Gear unit type DH7 [mm] DK [mm] L8 [mm] MS [Nm]
WA..10 16 16 69 8
WA..20 18 18 84 8 19
WA..20, WA..30, SA..37 20 20 84, 106, 104 8
FA..27, SA..47 25 25 88, 105 20 20
FA..37, KA..37, SA..47 105
30 30 20
SA..57 132
FA..47, KA..47, SA..57 35 35 132 20 21
FA..57, KA..57 142
FA..67, KA..67 40 40 156 40
SA..67 144 22
SA..67 45 45 144 40
FA..77, KA..77, SA..77 50 50 183 40
FA..87, KA..87 210
60 60 80
SA..77, SA..87 180, 220
FA..97, KA..97 270
70 70 80
SA..87, SA..97 220, 260
FA..107, KA..107, SA..97 90 90 313, 313, 255 200
FA..127, KA..127 100 100 373 200
FA..157, KA..157 120 120 460 200

Catalog – GM2004 77
 Design and Operating Notes
6 Installation/removal of gear units with hollow shafts and keys

2. Installa- You can also use the optional installation/removal kit for installation. You order the kit
tion/removal kit for the specific gear unit type(s) by quoting the part numbers in the table below. The
scope of delivery includes:
• Spacer tube for installation without contact shoulder (5)
• Retaining screw for installation (2)
• Forcing washer for removal (7)
• Locked nut for removal (8)
The short retaining screw supplied as standard is not used.

Customer shaft • The installation length of the customer shaft must be LK2. Do not use the spacer tube
if the customer shaft has a contact shoulder (A).
• The installation length of the customer shaft must be LK2. Use the spacer tube if the
customer shaft has a contact shoulder (B).

[A] [B]

[1] [4] [3] [2] [1] [4] [5] [3] [2]

Figure 15: Customer shaft with contact shoulder (A) and without contact shoulder (B)

(1) Hollow shaft (4) Customer shaft

(2) Retaining screw with washer (5) Spacer tube
(3) Circlip

Dimensions, tight-
ening torque and The retaining screw (2) must be tightened to the tightening torque MS given in the fol-
part numbers lowing table.
DH7 DK LK2 LX+2 C7 MS Part number installa-
Type
[mm] [mm] [mm] [mm] [mm] [Nm] tion/removal kit
WA..10 16 16 57 12.5 11 8 643 712 5
WA..20 18 18 72 16 12 8 643,682 X
WA..20, WA..30 72, 93
20 20 16 12 8 643 683 8
SA..37 92
FA..27, SA..47 25 25 72, 89 22 16 20 643 684 6
FA..37, KA..37 89
30 30 22 16 20 643 685 4
SA..47, SA..57 89, 116
FA..47, KA..47, SA..57 35 35 114 28 18 20 643 686 2
FA..57, KA..57 124
40 40 36 18 40 643 687 0
FA..67, KA..67, SA..67 138, 138, 126
SA..67 45 45 126 36 18 40 643 688 9
FA..77, KA..77, SA..77 50 50 165 36 18 40 643 689 7
FA..87, KA..87 188
60 60 42 22 80 643 690 0
SA..77, SA..87 158, 198
FA..97, KA..97 248
70 70 42 22 80 643 691 9
SA..87, SA..97 198, 238
FA..107, KA..107 287
90 90 50 26 200 643 692 7
SA..97 229
FA..127, KA..127 100 100 347 50 26 200 643 693 5
FA..157, KA..157 120 120 434 50 26 200 643 694 3

78 Catalog – GM2004
 Design and Operating Notes
Installation/removal of gear units with hollow shafts and keys
6

Removal Applies only if installation/removal kit was previously used for installation (→ Figure 15). 1
Proceed as follows for removal:
1. Loosen the retaining screw (6). 2
2. Remove the circlip (3) and, if used, the spacer tube (5).
3. According to Figure 16 place the forcing washer (7) and the locked nut (8) between 3
the customer shaft (4) and circlip (3).
4. Re-install the circlip (3). 4
5. Re-install the retaining screw (6). You can now push the gear unit off the shaft.
7

[6] 9

10
6
[8]
11

[7] [8] 12

13

14

[6] 15
Figure 16: Removal

(6) Retaining screw

16
(7) Forcing washer
(8) Locked nut for removal 17

18
DH7 C4 C5 C6 U-0.5 T -0.5 D3-0.5 L4 Part number installa-
Type M
[mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] tion/removal kit
WA..10 16 M5 5 5 12 4.5 18 15.7 50 643 712 5 19
WA..20 18 M6 5 6 13.5 5.5 20.5 17.7 25 643,682 X
WA..20, WA..30, SA..37 20 M6 5 6 15.5 5.5 22.5 19.7 25 643 683 8
FA27.., SA..47 25 M10 5 10 20 7.5 28 24.7 35 643 684 6 20
FA..37, KA..37, SA..47, SA..57 30 M10 5 10 25 7.5 33 29.7 35 643 685 4
FA..47, KA..47, SA..57 35 M12 5 12 29 9.5 38 34.7 45 643 686 2 21
FA..57, KA..57, FA..67, KA..67,
40 M16 5 12 34 11.5 41.9 39.7 50 643 687 0
SA..67
SA..67 45 M16 5 12 38.5 13.5 48.5 44.7 50 643 688 9 22
FA..77, KA..77, SA..77 50 M16 5 12 43.5 13.5 53.5 49.7 50 643 689 7
FA..87, KA..87, SA..77, SA..87 60 M20 5 16 56 17.5 64 59.7 60 643 690 0
FA..97, KA..97, SA..87, SA..97 70 M20 5 16 65.5 19.5 74.5 69.7 60 643 691 9
FA..107, KA..107, SA..97 90 M24 5 20 80 24.5 95 89.7 70 643 692 7
FA..127, KA..127 100 M24 5 20 89 27.5 106 99.7 70 643 693 5
FA..157, KA..157 120 M24 5 20 107 31 127 119.7 70 643 694 3

Catalog – GM2004 79
 Design and Operating Notes
6 Gear units with hollow shaft

6.3 Gear units with hollow shaft

Chamfers on hol- The following illustration shows the chamfers on parallel shaft helical and helical-bevel
low shafts gear units with hollow shaft:

Figure 17: Chamfers on hollow shafts

Gear Version
units with hollow shaft (A) with hollow shaft and shrink disk (H)
F..27 2 × 30° 0.5 × 45°
F../K..37 2 × 30° 0.5 × 45°
F../K..47 2 × 30° 0.5 × 45°
F../K..57 2 × 30° 0.5 × 45°
F../K..67 2 × 30° 0.5 × 45°
F../K..77 2 × 30° 0.5 × 45°
F../K..87 3 × 30° 0.5 × 45°
F../K..97 3 × 30° 0.5 × 45°
F../K..107 3 × 30° 3 × 2°
F../K..127 5 × 30° 1.5 × 30°
F../K..157 5 × 30° 1.5 × 30°
KH167 - 1.5 × 30°
KH187 - 1.5 × 30°

Special Please note for parallel shaft helical gearmotors with hollow shaft (FA..B, FV..B, FH..B,
motor/gear unit FAF, FVF, FHF, FA, FV, FH, FT, FAZ, FVZ, FHZ):
combinations • If you are using a customer shaft pushed through on the motor end, there may be a
collision when a "small gear unit" is used in combination with a "large motor".
• Check the motor dimension AC to decide whether there will be a collision with a
pushed-through customer shaft.

80 Catalog – GM2004
 Design and Operating Notes
TorqLOC® mounting system for gear units with hollow shaft
6

6.4 TorqLOC® mounting system for gear units with hollow shaft 1
®
Description of The TorqLOC hollow shaft mounting system is used for achieving a non-positive con-
TorqLOC® nection between customer shaft and the hollow shaft in the gear unit. As a result, the 2
TorqLOC® hollow shaft mounting system is an alternative to the hollow shaft with shrink
disk, the hollow shaft with key and the splined hollow shaft that have been used so far.
3
The TorqLOC® hollow shaft mounting system consists of the following components:

1 4
2

3
7

4 9
5

6
10
7
6
11

12

13

14

51939AXX 15
Figure 18: Components of the TorqLOC® hollow shaft mounting system
1. Customer shaft 16
2. Clamping ring
3. Conical bronze bushing 17
4. Hollow shaft in gear unit
5. Shrink disc 18
6. Conical steel bushing
7. Fixed cover
19

20
Advantages The TorqLOC® hollow shaft mounting system is characterized by the following advan-
TorqLOC® tages:
21
• Cost saving, because the customer shaft can be made from drawn material up to
quality h11. 22
• Cost saving because different customer shaft diameters can be covered by one hol-
low shaft diameter and different bushings.
• Simple installation since there is no need to accommodate any shaft connections.
• Removal is easy even after many hours of operation because the formation of con-
tact corrosion has been reduced and the conical connections can easily be released.

Catalog – GM2004 81
 Design and Operating Notes
6 TorqLOC® mounting system for gear units with hollow shaft

Technical Data The TorqLOC® hollow shaft mounting system is approved for input torques of 92 Nm to
4300 Nm.
The following gear units are available with TorqLOC® hollow shaft mounting system:
• Parallel shaft helical gear units in gear unit sizes 37 to 97 (FT37 ... FT97)
• Helical-bevel gear units in gear unit sizes 37 to 97 (KT37 ... KT97)
• Helical-worm gear units in gear unit sizes 37 to 97 (ST37 ... ST97)

Available options The following options are available for gear units with a TorqLOC® hollow shaft mount-
ing system:
• Helical-bevel and helical-worm gear units with TorqLOC® (KT.., ST..): The "torque
arm" (../T) option is available.
• Parallel shaft helical gear units with TorqLOC® (FT..): The "rubber buffer" (../G) op-
tion is available.

82 Catalog – GM2004
 Design and Operating Notes
Option, offset hollow shaft with shrink disk
6

6.5 Option, offset hollow shaft with shrink disk 1

As an option, gear units with a hollow shaft and shrink disk (parallel shaft helical gear
units FH/FHF/FHZ37-157, helical-bevel gear units KH/KHF/KHZ37-157 and helical- 2
worm gear units SH/SHF47-97) can be supplied with a larger bore diameter D’.
As standard, D’ = D. 3

D'

D'
D

D
7

03389AXX
Figure 19: Optional bore diameter D’ 8

9
Bore diameter
Gear units D / optionally D’
[mm] 10
FH/FHF/FHZ37, KH/KHF/KHZ37, SH/SHF/SHZ47 30 / 32 6
FH/FHF/FHZ47, KH/KHF/KHZ47, SH/SHF/SHZ57 35 / 36 11
FH/FHF/FHZ57, KH/KHF/KHZ57 40 / 42
FH/FHF/FHZ67, KH/KHF/KHZ67, SH/SHF/SHZ67 40 / 42
12
FH/FHF/FHZ77, KH/KHF/KHZ77, SH/SHF/SHZ77 50 / 52
FH/FHF/FHZ87, KH/KHF/KHZ87, SH/SHF/SHZ87 65 / 66
13
FH/FHF/FHZ97, KH/KHF/KHZ97, SH/SHF/SHZ97 75 / 76
FH/FHF/FHZ107, KH/KHF/KHZ107 95 / 96
FH/FHF/FHZ127, KH/KHF/KHZ127 105 / 106
14
FH/FHF/FHZ157, KH/KHF/KHZ157 125 / 126
15

Diameter D / D’ must be specified when ordering gear units with an offset hollow shaft 16
(optional bore diameter D’).

17
Sample order FH37 DT80N4 with hollow shaft 30/32 mm

18

19

20

21

22

Catalog – GM2004 83
 Design and Operating Notes
6 Option, offset hollow shaft with shrink disk

Parallel shaft helical gear unit with offset hollow shaft

04341AXX
Figure 20: Offset hollow shaft FH/FHF/FHZ37...77

84 Catalog – GM2004
 Design and Operating Notes
Option, offset hollow shaft with shrink disk
6

10
6
11

12

13

14

15

16

17

18

19

20

21

04342AXX 22
Figure 21: Offset hollow shaft FH/FHF/FHZ87...157

Catalog – GM2004 85
 Design and Operating Notes
6 Option, offset hollow shaft with shrink disk

Helical-bevel gear unit with offset hollow shaft

04343AXX
Figure 22: Offset hollow shaft KH/KHF/KHZ37...77

86 Catalog – GM2004
 Design and Operating Notes
Option, offset hollow shaft with shrink disk
6

10
6
11

12

13

14

15

16

17

18

19

20

21

04344AXX 22
Figure 23: Offset hollow shaft KH/KHF/KHZ87...157

Catalog – GM2004 87
 Design and Operating Notes
6 Option, offset hollow shaft with shrink disk

Helical-worm gear unit with offset hollow shaft

04345AXX
Figure 24: Offset hollow shaft SH/SHF/SHZ47...77

88 Catalog – GM2004
 Design and Operating Notes
Option, offset hollow shaft with shrink disk
6

10
6
11
04346AXX
Figure 25: Offset hollow shaft SH/SHF/SHZ87...97
12

13

14

15

16

17

18

19

20

21

22

Catalog – GM2004 89
 Design and Operating Notes
6 Adapter for installation of IEC motors

6.6 Adapter for installation of IEC motors

Gear unit type Adapter type B5 D E5 F5 G2 G5 S5 Z5 D1 L1 T1 U1

AM63 95 115 140 11 23 12.8 4
R..27, R..37 10 3.5 M8 72
F..27, F..37, F..47 AM711 110 130 160 14 30 16.3 5
120
K..37 AM801 12 19 40 21.8 6
S..37, S..47, S..57 1 130 165 4.5 200 M10 106
AM90 14 24 50 27.3 8
AM63 95 115 140 11 23 12.8 4
10 3.5 M8 66
AM71 110 130 160 14 30 16.3 5
R..472, R..57, R..67 AM80 12 19 40 21.8 6
F..57, F..67 130 165 4.5 200 M10 99
AM90 14 160 24 50 27.3 8
K..472, K..57, K..67
S..67 AM1001 16
180 215 250 134 28 60 31.3 8
AM1121 18 5 M12
1
AM132S/M 230 22 265 300 191 38 80 41.3 10
AM63 95 115 140 11 23 12.8 4
10 3.5 M8 60
AM71 110 130 160 14 30 16.3 5
AM80 12 19 40 21.8 6
R..77 130 165 4.5 200 M10 92
F..77 AM90 14 24 50 27.3 8
200
K..77 AM1001 16
S..77 1 180 215 250 126 28 60 31.3 8
AM112 18
1 5 M12
AM132S/M 22
230 265 300 179 38 80 41.3 10
AM132ML1 28
AM80 12 19 40 21.8 6
130 165 4.5 200 M10 87
AM90 14 24 50 27.3 8
AM100 16
R..87 180 215 250 121 28 60 31.3 8
F..87 AM112 18
5 250 M12
K..87 AM132S/M 22
S..873 230 265 300 174 38 80 41.3 10
AM132ML 28
1
AM160 28 42 45.3 12
250 300 6 350 M16 232 110
AM1801 32 48 51.8 14
1 Check dimension 1/2 G5 because component may protrude past foot-mounting surface if installed on R, K or S foot-mounted gear unit.
2 not with AM112
3 not with AM180

90 Catalog – GM2004
 Design and Operating Notes
Adapter for installation of IEC motors
6

10
6
11

12
Gear unit type Adapter type Fig. B5 D E5 F5 G2 G5 S5 Z5 D1 L1 T1 U1
AM100 16
13
180 215 250 116 28 60 31.3 8
AM112 18
5 M12
R..97
F..97
AM132S/M
230
22
265 300 169 38 80 41.3 10
14
AM132ML 1 28 300
K..97
S..971 AM160 28 42 45.3 12
AM180
250
32
300 6 350
M16
227
48 110 51.8 14
15
AM200 300 38 350 7 400 268 55 59.3 16
AM100
180
16
215 250 110 28 60 31.3 8
16
AM112 18
5 M12
AM132S/M 22
R..107 AM132ML 1
230
28
265 300 163 38 80 41.3 10 17
F..107 350
K..107 AM160 28 42 45.3 12
250 300 6 350 221
AM180 32
M16
48 110 51.8 14 18
AM200 300 38 350 400 262 55 59.3 16
7
AM225 2 350 38 400 450 277 60 140 64.4 18
AM132S/M 22
19
230 265 5 300 M12 156 38 80 41.3 10
AM132ML 28

R..137
AM160 1
250
28
300 6 400 350 214
42 45.3 12 20
AM180 32 48 110 51.8 14
M16
AM200 300 38 350 400 255 55 59.3 16
AM225 2 350 38 400
7
450 270 60 140 64.4 18
21
1 not with AM200
22

Catalog – GM2004 91
 Design and Operating Notes
6 Adapter for installation of IEC motors

Gear unit type Adapter type Fig. B5 D E5 F5 G2 G5 S5 Z5 D1 L1 T1 U1

AM132S/M 22 38
230 265 5 300 M12 148 80 41.3 10
AM132ML 28 38
AM160 1 28 42 45.3 12
R..147 250 300 6 350 206
AM180 32 48 110 51.8 14
F..127 450
K..127 AM200 300 38 350 400 247 55 59.3 16
AM225 350 38 400 450 262 60 64.4
7 18
AM250 2 65 140 69.4
450 48 500 550 336
AM280 75 79.9 20
M16
AM160 28 42 45.3 12
250 300 6 350 198
R..167 AM180 1 32 48 110 51.8 14
F..157 AM200 300 38 350 400 239 55 59.3 16
K..157 550
K..167 AM225 350 38 400 450 254 60 64.4
7 18
K..187 AM250 2 65 140 69.4
450 48 500 550 328
AM280 75 79.9 20

92 Catalog – GM2004
 Design and Operating Notes
Adapter for installation of servomotors
6

6.7 Adapter for installation of servomotors 1

10
6
11

12

13
Gear unit type Adapter type A5 B5 D E5 F5 G2 S5 Z5 Z121 Z122 D1 L1 T11 U11
AQ..80/1 11 23 12.8 4
14
60 75 M5
AQ..80/2 82 10 12 3 104.5 5.5 5.5
14 30 16.3 5
R..27, R..37
AQ..80/3 50 95 M6 15
AQ..100/1 80 100 M6
F..27, F..37, 129.5 - - 14 30 16.3 5
F..47 AQ..100/2 95 115 M8
K..37 AQ..100/3
100
80 100
120
M6
16
S..37, S..47, 10 12 143.5 7 14 19 40 21.8 6
AQ..100/4 95 115 4 M8
S..57 14 16
AQ..115/1 95
16 23 19 40 21.8 6
17
AQ..115/2 115 130 M8 152.5
110
AQ..115/3 21 16 24 50 27.3 8
AQ..80/1 11 23 12.8 4
18
60 75 M5
AQ..80/2 82 10 12 3 98 5.5 5.5
14 30 16.3 5
AQ..80/3 50 95 M6 19
AQ..100/1 80 100 M6
122.5 - - 14 30 16.3 5
AQ..100/2 95 115 M8
AQ..100/3
100
80 100 M6
20
R..47, R..57, 10 12 136.5 7 14 19 40 21.8 6
AQ..100/4 95 115 4 M8
R..67 14 16
F..57, F..67 AQ..115/1 95
160 16 23 19 40 21.8 6
21
K..47, K..57, AQ..115/2 115 130 M8 145.5
K..67 110
AQ..115/3 21 16 24 50 27.3 8
S..67
AQ..140/1 110 16
22
175 21 16 24 50 27.3 8
AQ..140/2 140 18 165 M10
130
AQ..140/3 22 188 24 22 32 60 35.5 10
5
AQ..190/1 130
22 237.5 26 24 32 60 35.3 10
AQ..190/2 190 215 M12
180 28
AQ..190/3 261.5 39 34 38 80 41.3 10
1 For versions with keyway (AQA..).
2 For version with clamping ring hub (AQH..).

Catalog – GM2004 93
 Design and Operating Notes
6 Adapter for installation of servomotors

Gear unit type Adapter type A5 B5 D E5 F5 G2 S5 Z5 Z121 Z122 D1 L1 T11 U11

AQ..80/1 75 11 23 12.8 4
60 10 M5
AQ..80/2 82 75 3 92 5.5 5.5
12 14 30 16.3 5
AQ..80/3 50 95 M6
AQ..100/1 80 100 M6
115.5 - - 14 30 16.3 5
AQ..100/2 95 115 M8
100
AQ..100/3 80 10 100 M6
12 129.5 7 14 19 40 21.8 6
AQ..100/4 95 115 4 M8
R..77 14
F..77 AQ..115/1 95 16
200 16 23 19 40 21.8 6
K..77 AQ..115/2 115 130 M8 138.5
S..77 110
AQ..115/3 21 16 24 50 27.3 8
AQ..140/1 110 16 167 21 16 24 50 27.3 8
AQ..140/2 140 18 165 M10
130 22
AQ..140/3 180 24 22 32 60 35.3 10
5
AQ..190/1 130
22 225.5 26 24 32 60 35.3 10
AQ..190/2 190 215 M12
180 28
AQ..190/3 249.5 39 34 38 80 41.3 10
AQ..100/1 80 100 M6
110.5 - - 14 30 16.3 5
AQ..100/2 95 115 M8
100
AQ..100/3 80 12 100 M6
124.5 7 14 19 40 21.8 6
AQ..100/4 95 14 115 4 M8
AQ..115/1 95 16
16 23 19 40 21.8 6
R..87 AQ..115/2 115 130 M8 133.5
F..87 110
AQ..115/3 250 21 16 24 50 27.3 8
K..87
S..87 AQ..140/1 110 16
162 21 16 24 50 27.3 8
AQ..140/2 140 18 165 M10
130
AQ..140/3 22 175 24 22 32 60 35.3 10
5
AQ..190/1 130
22 220.5 26 24 32 60 35.3 10
AQ..190/2 190 215 M12
180 28
AQ..190/3 244.5 39 34 38 80 41.3 10
1 For versions with keyway (AQA..).
2 For version with clamping ring hub (AQH..).

94 Catalog – GM2004
 Design and Operating Notes
Adapter for installation of servomotors
6

10
6
11

12

13
Gear unit type Adapter type A5 B5 D E5 F5 G2 S5 Z5 Z121 Z122 D1 L1 T11 U11
AQ..140/1 110 16 157 21 16 24 50 27.3 8
14
AQ..140/2 140 18 165 M10
R..97 130
AQ..140/3 22 170 24 22 32 60 35.3 10
F..97
K..97 AQ..190/1 130
300 15
S..97 22 215.5 26 24 32 60 35.3
AQ..190/2 190 215 M12 10
180 28
AQ..190/3 239.5 39 34 38 80 41.3 16
AQ..140/1 110 16 151 21 16 24 50 27.3 8
AQ..140/2 140 18 165 M10
R..107 AQ..140/3
130 22 164 24 22 32 60 35.3 10
17
F..107 5 350
K..107 AQ..190/1 130
22 209.5 26 24 32 60 35.3
AQ..190/2 190
180 28
215 M12 10 18
AQ..190/3 233.5 39 34 38 80 41.3
AQ..190/1 130
R..137 AQ..190/2
22
400
202.5 - 25 32 60 35.3 19
180 28
AQ..190/3 226.5 39 34 38 80 41.3
190 215 M12 10
R..147 AQ..190/1 130
194.5 26 24 32 60 35.3
20
22
F..127 AQ..190/2 450
180 28
K..127 AQ..190/3 218.5 39 34 38 80 41.3
21
1 For versions with keyway (AQA..).
2 For version with clamping ring hub (AQH..).
22

Catalog – GM2004 95
 Design and Operating Notes
6 Flange contours of RF.. and R..F gearmotors

6.8 Flange contours of RF.. and R..F gearmotors

04355AXX

Check dimensions L1 and L2 for selection and installation of output elements.

D2 L1
Type A1 D D1 D3 F1 I2 L L2
RF R..F RF R..F
120 38 72 3 2 2 6
RF07, R07F 140 20 22 38 - 85 3 40 40 2 - 6
160 - 100 3.5 2.5 - 6.5
120 46 65 3 1 1 5
RF17, R17F 140 20 25 46 - 78 3 40 40 1 - 5
160 - 95 3.5 1 - 6
120 54 66 3 1 1 6
RF27, R27F 140 25 30 54 - 79 3 50 50 3 - 7
160 - 92 3.5 3 - 7
120 63 70 3 5 4 7
RF37, R37F 160 25 35 60 - 96 3.5 50 50 1 - 7.5
200 - 119 3.5 1 - 7.5
140 64 82 3 4 1 6
RF47, R47F 160 30 35 72 - 96 3.5 60 60 0.5 - 6.5
200 - 116 3.5 0.5 - 6.5
160 75 96 3.5 4 2.5 5
RF57, R57F 200 35 40 76 - 116 3.5 70 70 0 - 5
250 - 160 4 0.5 - 5.5
200 90 118 3.5 2 4 7
RF67, R67F 35 50 90 70 70
250 - 160 4 1 - 7.5
250 100 160 4 0.5 2.5 7
RF77, R77F 40 52 112 80 80
300 - 210 4 0.5 - 7
300 122 210 4 0 1.5 8
RF87, R87F 50 62 123 100 100
350 - 226 5 1 - 9
350 236
RF97 60 72 136 5 120 120 0 9
450 320
350 157 232
RF107 70 82 5 140 140 0 11
450 186 316
450 316
RF137 90 108 180 5 170 170 0 10
550 416
450 316
RF147 110 125 210 5 210 210 0 10
550 416
550 416 5 1 10
RF167 120 145 290 210 210
660 517 6 2 11

96 Catalog – GM2004
 Design and Operating Notes
Fastening of gear units
6

6.9 Fastening of gear units 1

Use bolts of quality 8.8 to fasten gear units and gearmotors.
2
Exception In case of the following flange-mounted helical gearmotors (RF..) and foot/flange-
mounted helical gearmotors (R..F), use bolts of quality 10.9 to fasten the customer 3
flange to transmit the rated torque:
• RF37, R37F with flange ∅ 120 mm 4
• RF47, R47F with flange ∅ 140 mm
• RF57, R57F with flange ∅ 160 mm 7

6.10 Torque arms 9

Available torque
arms 10
Size 6
Gear units
27 37 47 57 67 77
11
KA, KH, KV, KT - 643 425 8 643 428 2 643 431 2 643 431 2 643 434 7
SA, SH, ST - 126 994 1 644 237 4 644 240 4 644 243 9 644 246 3
FA, FH, FV, FT
12
013 348 5 013 348 5 013 348 5 013 348 5 013 348 5 013 349 3
Rubber buffers (2 pcs.)

13
Size
Gear units
87 97 107 127 157
14
KA, KH, KV, KT 643 437 1 643 440 1 643 443 6 643 294 8 -
SA, SH, ST 644 249 8 644 252 8 - - - 15
FA, FH, FV, FT
013 349 3 013 350 7 013 350 7 013 351 5 013 347 7
Rubber buffers (2 pcs.) 16

17
Torque arms for As standard, torque arms are not available for gear unit sizes KH167.. and KH187...
KH167.., KH187.. Please contact SEW-EURODRIVE for design proposals if you require torque arms for 18
these gear units.
19

20

21

22

Catalog – GM2004 97
 Design and Operating Notes
6 Fixed covers

6.11 Fixed covers

As standard, parallel shaft helical gear units, helical-bevel gear units and helical-worm
gear units with hollow shafts and shrink disks from size 37 up to and including size 97
have a cover that turns with the unit. If for safety reasons fixed covers are required for
these gear units, you can order them for the respective gear unit types by quoting the
part numbers in the following tables. As standard, parallel shaft helical gear units and
helical-bevel gear units with hollow shafts and shrink disks of size 107 and parallel shaft
helical gear units of size 27 come equipped with a fixed cover.

1. 2.

03190AXX
Figure 26: Replacing a rotating cover with a fixed cover
1. Pull off the rotating cover.
2. Install and fasten fixed cover.

Part numbers and

dimensions

04356AXX

Parallel shaft helical gearmotors FH..37 FH..47 FH..57 FH..67 FH..77 FH..87 FH..97
Part number 643 513 0 643 514 9 643 515 7 643 515 7 643 516 5 643 517 3 643 518 1
Max. size of motor that can be
DT80.. DT80.. DT80.. DV132S DV160M DV180.. DV180..
mounted
G4 78 88 100 100 121 164 185
O1 157 188.5 207.5 221.5 255 295 363.5
X 2 4.5 7.5 6 6 4 6.5
Y 75 83 83 93 114 159 174

Helical-bevel gearmotors1 KH..37 KH..47 KH..57 KH..67 KH..77 KH..87 KH..97

Part number 643 513 0 643 514 9 643 515 7 643 515 7 643 516 5 643 517 3 643 518 1
G4 78 88 100 100 121 164 185
O2 95 111.5 122.5 129 147 172 210.5
X 0 1.5 5.5 3 1 2 4.5
Y 75 83 83 93 114 159 174
1 Not possible in foot-mounted helical-bevel gear units with hollow shafts and shrink disks (KH..B).

Helical-worm gearmotors SH..37 SH..47 SH..57 SH..67 SH..77 SH..87 SH..97

Part number 643 512 2 643 513 0 643 514 9 643 515 7 643 516 5 643 517 3 643 518 1
G4 59 78 88 100 121 164 185
O2 88 95 111.5 123 147 176 204.5
X 1 0 1.5 3 1 0 0.5
Y 53 75 83 93 114 159 174

98 Catalog – GM2004