Personal Embroidery Design Software System

Quick Reference Guide

Ver. 7

ENGLISH
XE1182-001
Printed in China

<< PE-Design Ver.7.0 QRG >> cover 1-4

 IMPORTANT INFORMATION: REGULATIONS

Federal Communications Commissions (FCC) Declaration of Conformity

(For USA Only)
Responsible Party: Brother International Corporation
100 Somerset Corporate Boulevard
Bridgewater, NJ 08807-0911 USA

declares that the product

Product Name: Brother USB Writer

Model Number: PE-DESIGN

complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any inter-
ference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for Class B digital de-
vice, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turn-
ing the equipment off and on, the user is encouraged to try to correct the interference by one
or more of the following measures:

– Reorient or relocate the receiving antenna.

– Increase the separation between the equipment and receiver.
– Consult the dealer or an experienced radio/TV technician for help.
– Changes or modifications not expressly approved by the manufacturer or local sales dis-
tributor could void the user’s authority to operate the equipment.

Canadian Department of Communications Compliance Statement

(For Canada Only)
This digital apparatus does not exceed the Class B limits for radio noise emission from a
digital apparatus as set out in the interference-causing equipment standard entitled “Digital
Apparatus”, ICES-003 of the Department of Communications.

Radio Interference
(Other than USA and Canada)
This machine complies with EN55022 (CISPR Publication 22) /Class B.

PED7_QSG.indb 1 02.06.2006 20:06:53

 Congratulations on choosing our product!
Thank you very much for purchasing our product. To obtain the best performance from this unit
and to ensure safe and correct operation, please read this Quick Reference Guide carefully, and
then keep it in a safe place together with your warranty.

Please read before using this product

For designing beautiful embroidery patterns
• This system allows you to create a wide variety of embroidery patterns and supports a
wider range of sewing attribute settings (thread density, sewing pitch, etc.). However, the
final result will depend on your particular sewing machine model. We recommend that
you make a trial sewing sample with your sewing data before sewing on the final material.
For safe operation
• Avoid dropping a needle, a piece of wire or other metallic objects into the unit or into the
card slot.
• Do not store anything on the unit.
For a longer service life
• When storing the unit, avoid direct sunlight and high humidity locations. Do not store the
unit close to a heater, iron or other hot objects.
• Do not spill water or other liquids on the unit or cards.
• Do not drop or hit the unit.
For repairs or adjustments
• In the event that a malfunction occurs or adjustment is required, please consult your near-
est service center.
Notice
Neither this Quick Reference Guide nor the Instruction Manual explains how to use your compu-
ter under Windows®. Please refer to the Windows® manuals.

Copyright acknowledgment
Windows® is a registered trademark of Microsoft Corporation. Other product names mentioned in
the Instruction Manual and Quick Reference Guide may be trademarks of registered trademarks
of their respective companies and are hereby acknowledged.
Important
Using this unit for unauthorized copying of material from embroidery cards, newspapers and
magazines for commercial purpose is an infringement of copyrights which is punishable by law.

Caution
The software included with this product is protected by copyright laws. This software can be used
or copied only in accordance with the copyright laws.

SAVE THESE INSTRUCTIONS

This product is intended for household use.

For additional product information and updates, visit our web site at:
http://www.brother.com/ or http://solutions.brother.com/

PED7_QSG_00.indd 1 22.06.2006 17:57:33

 Table of Contents

Quick Reference Guide

Before Use....................................................................................4
Features .............................................................................................4
Basic Operation Map .........................................................................9
Introduction..................................................................................... 10
Installation (Please read before Installing!) ...................................... 12
Using this Quick Reference Guide ................................................... 23
Using the Instruction Manual .......................................................... 23
Sew Types ........................................................................................28

Getting Started ...........................................................................30

Starting Up/Exiting Applications ......................................................30
Understanding Windows and Using Tools........................................ 31
Automatically Converting an Image to an Embroidery Design (Auto
Punch Function) ...............................................................................36

Troubleshooting .........................................................................46

PED7_QSG_00.indd Sec1:2 02.06.2006 20:25:37

 Table of Contents

Instruction Manual (viewed from computer)

After the software has been installed, the Instruction Manual can be viewed from the software appli-
cation window. The Instruction Manual provides operating procedures and descriptions for the vari-
ous functions of the software. Click on Help in the tool bar and then click on Instruction Manual.

Basic Operation
Starting up/Exiting Applications
Understanding Windows and Using Tools
Automatically Converting an Image to an Embroidery Design
(Auto Punch Function)
Automatically Converting an Image to an Embroidery Design
(Cross Stitch Function)
Automatically Converting a Photo to an Embroidery Design
Manually Creating Embroidery Patterns From Images
Arranging Embroidery Patterns
Managing Embroidery designs
Entering Monograms
Creating Appliqués

Advanced Operation
Automatically Converting an Image to an Embroidery Design
(Layout & Editing/Image to Stitch Wizard)
Arranging Embroidery Designs (Layout & Editing)
Manually Creating Embroidery Patterns From Images (Design Center)
Creating Custom Fonts (Font Creator)
Creating Custom Stitch Patterns (Programmable Stitch Creator)
Listing/Managing Embroidery Design Files (Design Database)
Menus/Tools

Index

PED7_QSG_00.indd Sec1:3 08.06.2006 10:38:24

 Before Use

Features
What You Can Do With This Software
This software provides digitizing and editing capabilities, allowing you the creative freedom to
design original embroidery. Easily turn illustrations, photos and lettering into custom embroidery
designs.

Automatically Create an Embroidery Pattern From an Image

Refer to “Automatically Converting an Image to an Embroidery Design (Auto Punch Function)” in

the Instruction Manual.

Automatically Create an Embroidery Pattern From a Photo

Refer to “Automatically Converting a Photo to an Embroidery Design (Photo Stitch Function)” in

the Instruction Manual.

PED7_QSG.indb Sec1:4 02.06.2006 20:06:56

 Features

Easily Create Custom Fonts

Custom fonts can be created using Font Creator. These fonts can be recalled to be used in Layout
& Editing.

Refer to “Manually Creating Custom Fonts (Font Creator)” in the Instruction Manual.

Have Fun Creating Embroidery Patterns Manually

You can combine embroidery patterns or apply stitching to drawings and text. In addition, you
can design a wider variety of embroidery patterns by using the many sew types available.

“Arranging Embroidery Patterns (Layout & Editing)” in the Instruction Manual.

PED7_QSG_00.indd Sec1:5 08.06.2006 10:38:52

 New Features of Version 7

■ Stitch generation features

• Added Line Sewing Type: Triple Stitch
• Added Region Sewing Type: Random Walking Stitch (stippling-style stitch)
• Variations of under sewing
- Added new under sewing type to the Region Sewing Attributes
- Under sewing can be set for zigzag stitching, manual punching, and text
• Motif stitch can be set to manual punching
• Piping Stitch can be set to regions
• New zigzag stitch corners have been added to the Line Sewing Attributes
- (2 styles of Sharp Corners)
• Expanded motif sizing and spacing
- The motif can be spaced vertically and horizontally
- The motif can be sized up to 100 x 100 mm (3.94 x 3.94 inches)

■ Editing Functions and user interface

• Auto repeat using arrow keys
• Can save Personal Sewing Attribute settings
Layout & Editing:
• Newly created custom Fonts can be used in Layout & Editing. (From Font Creator)
• New small Fonts (Minimum Font size 3.0mm (0.12 inch))
• Embroidery letters of 2-byte characters for True Type Font can be entered. (Japanese, Chi-
nese, Korean, etc.)
• Monogramming function includes more decorative frames. All built in fonts, True Type
Font, and custom created fonts from Font Creator can now be used with the Monogram
function
• Transforming text can be done by dragging. Kerning, Sizing, Rotating, vertical offset can be
done by dragging the individual letters
• Can generate a curved outline in the Auto Punch function
• Improved editing functions for curved outlines
• Shape tool has been added to the left tool bar with 24 built in shapes
• Six additional stitch formats can be imported and exported: All formats include:
.pec, .pes, .dst, .exp, .pcs, .hus, .vip, .shv, .jef, .sew, .csd, .xxx and .phc
(.pec and .phc are import only.)
• Additional fading levels in Image display
• Enables the ability to drag & drop clip art, pes files, and stitch format files into Layout &
Editing

PED7_QSG_00.indd Sec1:6 05.06.2006 19:42:36

 Features

• Improved Photo Stitch function:

- Easier process to create an embroidery file from a Photo
- Improved processing speed and color selection
Design Center:
• “Detect Outlines” function to select the outline of an image in “Cut out to Line Image”
dialog
• “Figure Handle Stage” has the ability to connect/split a line
• Enables the color of a portion of the outline to be changed in the Sewing Setting Stage
• New button to easily export a design from Sew Setting Stage to Layout & Editing
• Allows up to 20 Undo/Redo operations
• Enables to display template image on Figure Handle Stage and enable to display original
image on Sew Setting Stage in the Reference Window
Design Data Base
• Can drag and drop a design from the Design Data Base into Layout & Editing
• Can write to an Original card from Design Data Base
• Property box when outputting CSV files and printing, enables to output the thread codes

■ General
• New Font Creator program to create custom fonts
• Automatically checks and updates the newest version
• Additional sample files for images and embroidery patterns

Applications of the Software

This package consists of five applications.

■ Layout & Editing

Layout & Editing is used to automatically create embroidery patterns from images, and to com-
bine images and text to create embroidery patterns that can be written to an original card. The
images may come from scanning a printed image or can be created with an application like
Paint®.
After assembling the different parts of your embroidery pattern, you can use the layout functions
to adjust their relative position, orientation and scale.
When an embroidery design is complete, you can save it and write it to an original card.
The original card can then be inserted into your embroidery machine for the embroidery design
to be sewn.

PED7_QSG_00.indd Sec1:7 05.06.2006 19:42:37

 ■ Design Center
Design Center is used to manually create embroidery patterns from images using a four-stage pro-
cedure. The images may come from scanning a printed image or can be created with an appli-
cation like Paint®. Design Center automatically detects outlines in the image and replaces them
with broken lines that can be edited and assigned sewing attributes.
• The four stages of Design Center
Original Image Stage:
Open an image file and select one or more colors that the application will use to trace the
outlines.
Line Image Stage:
The original color image is replaced with a black-and-white image (the colors selected in the
Original Image Stage become black, and all other colors become white).
This image can be edited using pens of different thicknesses. (You can also start with this step
to draw a black-and-white image by hand.)
When the image is ready, start the automatic tracing process.
Figure Handle Stage:
The black-and-white image is replaced with a set of outlines made of editable broken lines.
You can edit the broken lines by moving, inserting or deleting editing points.
Sew Setting Stage:
In this final step, apply sewing attributes (thread color and sew type) to the outlines and the
inside regions.
At any stage, you can save your work to retrieve it later.
Saving your work as you move through the stages will be helpful if you make changes, then
later decide to use the original pattern.
When your image has reached the Sew Setting Stage, you can import it into Layout & Editing,
where the image can be moved and scaled as a single pattern.

■ Programmable Stitch Creator

Programmable Stitch Creator allows you to create, edit and save fill/stamp and motif stitch pat-
terns that can be applied as a programmable fill stitch or motif stitch, or as a stamp to the en-
closed regions of embroidery patterns both in Design Center and Layout & Editing.

■ Font Creator
Font Creator allows you to create, edit and save custom font characters, which can be used in
Layout & Editing.

■ Design Database
Design Database allows you to easily preview the embroidery design files on your computer so
that you can find the desired design, which can be opened with or imported into Layout & Edit-
ing. From Design Database, you can also convert the files to other formats (.dst, .exp, .pcs, .hus,
.vip, .shv, .jef, .sew, .csd, and .xxx), or print or output as an HTML file images of the embroidery
designs in a selected folder. In addition, the sewing information for the embroidery designs in a
selected folder can be outputted as a CSV file for use in other database applications.
In addition, the embroidery designs can be written to original cards.

PED7_QSG.indb Sec1:8 02.06.2006 20:06:59

 Basic Operation Map

Basic Operation Map

Design Center Font Creator

Manually create embroidery Create custom font patterns
patterns from image •file name: .pef
•file name: .pel, .pem

Custom
Lettering
Layout & Editing Digitizes
Combine different patterns
into an embroidery design
•file name: .pes Automatically
Converts Image
Custom to Embroidery
Designs Designs

Programmable Design Database

Stitch Creator Manage design files
Create custom stitch patterns
•file name: .pas, .pmf

Embroidery
Machine

PED7_QSG.indb Sec1:9 02.06.2006 20:06:59

 Introduction
Package Contents
Check that the following items are included. If anything is missing or damaged, contact your author-
ized dealer or Brother Customer Service.

Version 7 (full version):

USB card writer module

CD-ROM Original card Quick Reference Guide Template

Contains the software,

Instruction Manual
(HTML format) and
Instruction Manual
(PDF format).

Version 7 upgrade for version 5 or 6:

CD-ROM Quick Reference Guide Template

Contains the software,

Instruction Manual
(HTML format) and
Instruction Manual
(PDF format).

Note:
• The USB card writer module and the original card are not included in the kit provided for upgrad-
ing from version 5 or 6.

10

PED7_QSG.indb Sec1:10 02.06.2006 20:06:59

 Introduction

Optional Supplies
Original card

Note:
• The only original cards that can be used with this USB card writer module are those like the one
enclosed or optional original cards of the same type.

Memo:
• Additional blank original cards can be purchased through an authorized dealer.

Principal Parts

LED indicator
This indicator lights up when the unit is turned on,
and flashes when the USB card writer module is
communicating with the computer.

Note:
•Never remove an original card or unplug the
USB cable while this indicator is flashing.

Card slot
Insert an original card/embroidery USB connector
card here. Connect to the computer.

Memo:
• Since power is supplied to the USB card writer module through the USB connection to the compu-
ter, there is no power supply cable or power switch.
• Be sure to keep original cards away from high humidity, direct sunlight, static electricity and strong
shocks. Furthermore, do not bend the cards.

11

PED7_QSG.indb Sec1:11 02.06.2006 20:07:00

 Installation (Please read before Installing!)
Please Read Before Installation
• Before beginning the installation, check that the computer meets the system requirements.
• In order to install the software, you must log on to the computer using an account with administra-
tor privileges. For details on logging on to the computer using an account with administrator privi-
leges, refer to the Windows manual.
• The installation procedure is described for Windows® XP. The procedure and dialog boxes for other
operating systems may be slightly different.
• If the installation is canceled before it is completed or if the procedure is not performed as de-
scribed, the software will not be installed correctly.
• Do not remove the CD-ROM from the CD-ROM drive of the computer while the installation is be-
ing performed. Remove the CD-ROM after the installation is completed.
• Before turning on the computer, be sure to disconnect the USB card writer module.
• In order to upgrade the USB card writer module, you must be able to connect to the Internet. If you
cannot connect to the Internet, contact your authorized dealer or Brother Customer Service.
• When upgrading from version 5.02 or later, skip STEP 2 and continue with STEP 3.
• If the USB card writer module is not upgraded, it can only be used the limited number of times that the soft-
ware can be used. In order to upgrade the USB card writer module, be sure to perform STEP 3 on page 19.

Installation Procedure
The installation procedure is different depending on whether the full version or an upgrade of the
software is being installed. Be sure to perform the installation procedures listed below.

■ Installing version 7.0 (full version)

[STEP 1] Installing the software................................................................................ ☞ page 13
[STEP 2] Installing the driver for the card writer module ......................................... ☞ page 16

■ Upgrading from version 5.0 or 5.01

[STEP 1] Installing the software................................................................................ ☞ page 13
[STEP 2] Installing the driver for the card writer module ......................................... ☞ page 16
[STEP 3] Upgrading the USB card writer module ..................................................... ☞ page 19

■ Upgrading from version 5.02 or later

[STEP 1] Installing the software................................................................................ ☞ page 13

Memo:
• When upgrading from version 5.02 or later, STEP 2 is not performed.

[STEP 3] Upgrading the USB card writer module ..................................................... ☞ page 19

12

PED7_QSG.indb Sec1:12 02.06.2006 20:07:00

 Installation

System Requirements
Before installing the software on your computer, make sure that the computer meets the following
minimum PC requirements.
Computer IBM-PC or compatible computer
Operating system Windows® 2000, XP
Processor Pentium III 800 MHz or higher
Memory 128 MB (512 MB or more is recommended.)
Hard disk free space 200 MB
Monitor SVGA (800 x 600), 16-bit color or higher
Port 1 available USB
A graphic printer that is supported by your system
Printer
(if you wish to print your images)
CD-ROM drive Required for installation

Note:
• Power is supplied to the USB card writer module through the USB connection. Connect the USB
card writer module to a USB connector on the computer or to a self-powered USB hub that can
supply enough power to the card writer module. If the card writer module is not connected in this
way, it may not operate correctly.
• This product may not operate correctly with some computers and USB expansion cards.

Step 1: Installing the Software

This section describes how to install the application software.
Note:
Insert the enclosed • If the installation is interrupted or
CD-ROM into the not performed as described, the
computer’s CD-ROM software will not be installed cor-
drive. rectly.
• Before turning on the computer,
be sure to DISCONNECT the USB
card writer module.
• In order to install the software, you
must log on to the computer using
an account with administrator
privileges.

13

PED7_QSG.indb Sec1:13 02.06.2006 20:07:00

 → After a short while, the Choose Setup Language dialog
box automatically appears. Memo:
• The following installation procedure
includes descriptions and dialog box-
es for Windows® XP. The procedure
and dialog boxes for other operating
systems may be slightly different.

Memo:
• If the installer does not automati-
cally start up:
1. Click the Start button.
Select the desired language, and then click OK. 2. Click Run.
→ The Run dialog box appears.
3. Type in the full path to the in-
staller, and then click OK to start
→ The InstallShield Wizard starts up, and the first dialog up the installer.
box appears. For example: D:\setup.exe (where
“D:” is the name of the CD-ROM
drive)

Click Next to continue with the installation.

Memo:
• To install the application into a dif-
→ A dialog box appears, allowing you to select the folder ferent folder:
where the software will be installed.
1. Click Browse.
2. In the Choose Folder dialog box
that appeared, select the drive and
folder. (If necessary, type in the
name of a new folder.)
3. Click OK.
→ The Choose Destination
Location dialog box of the
InstallShield Wizard shows the
Click Next to install the application into the selected folder.
default folder.
4. Click Next to install the applica-
tion into the selected folder.
• To return to the previous step, click
Back.
• To quit the installation, click
Cancel.

14

PED7_QSG.indb Sec1:14 02.06.2006 20:07:01

 Installation

→ When the installation is completed, the following dia-

log box appears, suggesting that the computer be re-
started.

Note:
• Even though the installation is
completed, do not remove the
CD-ROM from the computer’s
CD-ROM drive.

Click Finish to restart the computer and com-

plete the installation of the software.

Memo:
• If the following dialog box appears, it is not necessary to restart the
computer.

Click Finish to complete the installation of

the software.

15

PED7_QSG.indb Sec1:15 02.06.2006 20:07:02

 Step 2: Installing the Driver for the Card Writer Module
This section describes how to install the driver for the card writer
module. Note:
a Plug the USB connector into the USB port on • If you upgrading from version 5.02
or later, skip this section and con-
the computer. tinue with the procedure described
in “[STEP 3] Upgrading the USB
Make sure that the connector is fully inserted. card writer module” on page 19.

b Install the driver for the card writer module.

■ For Windows® XP with Service Pack 2 already
installed and connected to the Internet:

Select Yes, this time only,

and then click Next. Memo:
• To check whether or not Service
Pack 2 is installed, click Start, and
then click on Control Panel, then,
double-click on System to open the
Properties page.

Note:
• Depending on the computer, this
dialog box may not appear. If it
does not appear, skip this step and
continue with the procedure.

Select Install the software auto-

matically (Recommended), and
then click Next.

16

PED7_QSG.indb Sec1:16 02.06.2006 20:07:03

 Installation

■ For Windows® XP without Service Pack 2 in-

stalled and connected to the Internet:
The installation of the driver is completed automatically
(Steps b through c are not required.).

■ For Windows® XP not connected to the In-

ternet:

Select No, not this time, and

then click Next. Note:
• Depending on the computer, this
dialog box may not appear. If it
does not appear, skip this step and
continue with the procedure.

Select Install from a list or spe-

cific location (Advanced), and
then click Next.

17

PED7_QSG.indb Sec1:17 02.06.2006 20:07:04

 To install the new driver for the USB card writer
module, select Search removable media (floppy,
CD-ROM...), and then click Next.

■ For Windows® 2000:

Select Search for a suitable driver for my
device (recommended), and then click Next.

Select CD-ROM drives, and then click Next.

18

PED7_QSG.indb Sec1:18 02.06.2006 20:07:05

 Installation

c Follow the instructions of the Found New

Hardware Wizard (or Add New Hardware Wiz-
ard) to complete the installation of the driver.

d Remove the CD-ROM from the computer’s

CD-ROM drive.

Step 3: Upgrading the USB Card Writer Module

This section describes how to upgrade the USB card writer module
for version 7. Users upgrading from version 5 or 6 must upgrade Note:
the card writer. After installing version 7, immediately follow the • In order to upgrade the USB card
procedure below to upgrade the card writer for version 7. writer module, you must be able to
connect to the Internet. If you can-
a Start up Layout & Editing. not connect to the Internet, contact
your authorized dealer or Brother
→ The dialog box shown below appears. Customer Service.

To begin the upgrade, click Upgrade now.

→ The Upgrade wizard starts up, and the first dialog box
shown below appears.

Click Next.

19

PED7_QSG.indb Sec1:19 02.06.2006 20:07:06

 Note:
• If the product ID is incorrectly en-
tered, the message “The product ID
is incorrect. Check that a mistake
was not made during typing.” ap-
pears.
• The uppercase letters “I” and “O”
are not used in the product ID.

Type in the 15-digit product ID on the label at-

tached to the CD-ROM case, and then click Next.

→ The entered product ID and the serial number auto-

matically retrieved from the USB card writer module is
displayed.

Note:
• If a firewall is being used, set it so
that the Internet can temporarily be
accessed while the upgrade key is
Click Next to access our server through the being obtained.
Internet and retrieve the upgrade key.

→ If the upgrade key has been successfully retrieved, the

dialog box shown below appears.

Click Next to begin upgrading the USB card

writer module.

20

PED7_QSG.indb Sec1:20 02.06.2006 20:07:06

 Installation

→ If the upgrade has been completed successfully, the

dialog box shown below appears.

Note:
• If a warning appears at any time,
follow the instructions that are
displayed.

Online Registration
If you wish to be contacted about upgrades and provided with
important information such as future product developments and Note:
improvements, you can register your product online by follow- • Online registration may not be
ing a simple registration procedure. available in some areas.
Click Online Registration on the Help menu of Layout & Editing
to start up the installed Web browser and open the online regis-
tration page on our Web site.

Checking for the Latest Version of the Program

Click Help in Layout & Editing, then Check for updates.
The software is checked to determine whether or not it is the Note:
latest version. • This feature cannot be used if the
If the message shown below appears, the latest version of the computer is not connected to the
software is being used. Internet.

If the message shown below appears, the latest version of the

software is not being used. Click Yes, and then download the
latest version of the software from the Web site.

Memo:
• If the Always check Latest ver-
sion when launching check box is
selected, the software is checked at
startup to determine whether or not it
is the latest version.

21

PED7_QSG.indb Sec1:21 02.06.2006 20:07:07

 Uninstallation

a Click the Start button in the task bar, and then

click Control Panel.
b In the Control Panel window, double-click
Add or Remove Programs.
c In the dialog box that appeared, select this
software, and then click Change/Remove.

Technical Support
Contact Technical Support if you have a problem. Please check
the company web site (http://www.brother.com/) to find the
Technical Support in your area.

Note:
• On the above website, first select your country. If your country is not
listed, reference “others”.
• Before contacting web site:
1. Please have your Windows® Operating System updated to
the most current version.
2. The make and model number of the computer that you are using as
well as the Windows® Operating System version.
3. Information about any error messages that appear.
This information will help expedite your questions more quickly.

22

PED7_QSG.indb Sec1:22 02.06.2006 20:07:08

 Using this Quick Reference Guide/Using the Instruction Manual

Using this Quick Reference Guide

This guide contains descriptions about the preparations necessary to begin using the software. Follow
the instructions provided in this manual to complete the preparation and installation of the applica-
tion.
In addition, this guide has practice exercises for understanding the operation of the software.

For details about the functions and operating procedures for the software, refer to the Instruction
Manual, which is located in the Help menu of each application.

Using the Instruction Manual

After the software has been installed, the Instruction Manual (HTML format) can be viewed from the
Start menu and each application.

Contents of the Instruction Manual

Details on the functions and operating procedures for the applications are provided in easy-to-
understand descriptions. These applications can be used most efficiently by using the menu com-
mands and tools in addition to the described methods for correcting errors.
Basic Operation
By following the step-by-step instructions for the desired operation, you can become familiar
with the basic functions of the applications.
Advanced Operation
Details on each function are provided. Select the desired operation to display the corresponding
details.
Operation Search
Details on the main functions are provided. Select the desired operation to display the corre-
sponding details.
Index
Search for functions to view more information.

System requirements
The following environment is recommended in order to view the Instruction Manual.
Web browser: Microsoft Internet Explorer® Ver.5.01 or later

23

PED7_QSG_03.indd Sec1:23 08.06.2006 10:39:55

 Opening the Instruction Manual

Note:
•Before opening the Instruction Manual, make sure that the software has been installed on the com-
puter. For details, refer to “Installation (Please read before Installing!)” on page 12.

■ From the Start menu

a Click , point to All Programs, then PE-DESIGN Ver7, and then click
Instruction Manual.
The introduction page appears.

24

PED7_QSG_03.indd Sec1:24 08.06.2006 10:40:14

 Using the Instruction Manual

b Click Start Instruction Manual.

The Instruction Manual appears.
Operation buttons
Buttons for operations, such as changing the page display and printing.

Support menu
Menu for
providing help
in using the
manual or
viewing the
desired infor-
mation.
Main menu
Click the but-
ton in the main
menu for the
desired opera-
tion.

25

PED7_QSG_03.indd Sec1:25 19.06.2006 22:22:43

 ■ From the Help menu of the application
As an example, the procedure for opening the Instruction Manual from Layout & Editing fol-
lows.

a Click Help, then Instruction Manual.

b Click Start Instruction Manual.

26

PED7_QSG_03.indd Sec1:26 08.06.2006 11:18:01

 Using the Instruction Manual

The introduction page appears.

c Click the button for the desired topic.

Memo:
• If the Instruction Manual does not appear even after a button is clicked, change the Internet Ex-
plorer® settings according to the instructions that appear in the introduction page.

Instruction Manual (PDF format)

For a printer-friendly version of the Instruction Manual use the PDF file. This file would normally
be available in the folder at the path C:\Program Files\Brother\PE-DESIGN Ver7\Manual on the
drive where PE-DESIGN was installed.

Memo:
• Adobe® Reader® is required for viewing and printing the PDF version of the Instruction Manual.

27

PED7_QSG_03.indd Sec1:27 08.06.2006 11:18:03

 Sew Types
The sewing attributes for each sew type are first set to their default settings; however, by changing
the settings of the sewing attributes, you can create custom stitching. For details, refer to “Line sew-
ing attributes” and “Region sewing attributes” (Layout & Editing and Design Center) of the Instruction
Manual.

■ Line sew types

Zigzag Stitch Running Stitch/Triple Stitch New!

Motif Stitch E/V Stitch

■ Region sew types

Satin Stitch Fill Stitch

Programmable Fill Stitch Motif Stitch

28

PED7_QSG_04.indd Sec1:28 21.06.2006 13:48:59

 Sew Types

Cross Stitch Concentric Circle Stitch

Radial Stitch Spiral Stitch

Piping Stitch New! Piping Stitch (motif setting) New!

Random Walking Stitch New!

Memo:
• The stitching for the programmable fill stitch and the motif stitch depends on the selected stitch
pattern. For details, refer to “Programmable fill stitch” and “Motif stitch” on “ Line (or Region) sew-
ing attributes” of the Instruction Manual.

29

PED7_QSG_04.indd Sec1:29 09.06.2006 9:20:01

 Getting Started

Starting Up/Exiting Applications

Starting Up Layout & Editing
Layout & Editing is used to automatically create embroidery patterns from images and to create
embroidery patterns by combining drawn patterns and text. As an example, the Layout & Editing
window is shown below.

a Click , select All Programs, then Memo:

PE-DESIGN Ver7. Select Layout & Editing to • To fill the entire screen with the
open the Layout & Editing window. Layout & Editing window, click the
maximize button on the right end of
→ The Layout & Editing window appears. the title bar.
• At this time, you can change the
Design Page properties by using the
menu command Option – Design
Page Property. (For more details,
refer to “Specifying the Design Page
Size and Color” of the Instruction
Manual) For this example, we will
not change the Design Page set-
tings.

Exiting the Application

When you are finished using an application, you can close it.

a Click File in the menu bar, and then click Exit. Memo:
→ The window closes. • The window can also be closed by
clicking the close button on the top
right corner of the title bar.

30

PED7_QSG.indb Sec1:30 02.06.2006 20:07:11

 Starting Up/Exiting Applications/Understanding Windows and Using Tools

Understanding Windows and Using Tools

Layout & Editing Window
The default value for the Design Page size in this example is 100 x 100 mm.

1 12
2
3 11
4
10
9
5
8

1 Title bar 7 Reference Window

2 Menu bar Displays all patterns in the work area, giv-
Provides access to the functions. ing you an overview while you work on
a detailed area. (For more details, refer to
3 Toolbar
“Viewing Patterns in the Reference Win-
Provides shortcuts for the menu commands. dow” of the Instruction Manual.)
4 Sewing Attributes bar 8 Design Page
Sets the sewing attributes (color and sew The actual part of the work area that can be
type) of lines and regions in the pattern. saved and sewn.
5 Tool Box 9 Work area
Used to create, select and edit patterns. 10 Minimize button
6 Status bar 11 Maximize button
Provides helpful information. 12 Close button

31

PED7_QSG_05.indd Sec1:31 13.06.2006 16:37:47

 Design Center Window
The default value for the Design Page size in this example is 100 x 100 mm.

1 12
2
3 11
4
10

5
9
8

1 Title bar 6 Status bar

2 Menu bar Provides helpful information.
Provides access to the functions. 7 Reference Window
3 Toolbar Displays all outlines and patterns in the
Provides shortcuts for the menu commands. work area, giving you an overview while
you work on a detailed area. (For more
4 Sewing Attributes bar
details, refer to “Viewing patterns in the ref-
Sets the sewing attributes (color and sew erence window” of the Instruction Manual.)
type) of the lines and regions in the pattern
8 Design Page
(only in the Sew Setting Stage)
The actual part of the work area that can be
5 Tool Box saved and sewn.
Used to select and edit the image or pat- 9 Work area
tern. Original Image Stage has no Tool Box;
10 Minimize button
the other stages all have a different tools in
the Tool Box (The window for the Sew Set- 11 Maximize button
ting Stage is shown on this page.). 12 Close button

32

PED7_QSG.indb Sec2:32 02.06.2006 20:07:12

 Understanding Windows and Using Tools

Font Creator Window

1 14
2
3 13
4 12
11
5
10

9
8

6
10

1 Title bar 9 Guidelines (fixed)

2 Menu bar The distance between the two guidelines
Provides access to the functions. becomes the height of the font created.
3 Toolbar 10 Guidelines (movable)
Provides shortcuts for the menu commands. These guidelines can be moved accord-
ing to the shape of the created font. The
4 Select Character bar
distance between the two red guidelines
Allows characters from created fonts to be becomes the width of the font created. The
selected. three blue guidelines are positioning lines
5 Tool Box for accent positions, the height of small
Used to select and create font pattern. characters, and the bottom edge of small
6 Status bar characters.
Provides helpful information. 11 Work area
7 Preview window 12 Minimize button
Shows how the stitch pattern will be sewn. 13 Maximize button
8 Design Page 14 Close button
The actual part of the work area that can be
saved.

33

PED7_QSG.indb Sec3:33 02.06.2006 20:07:13

 Programmable Stitch Creator Window

1 11
2
3 10
9
8
4
7

1 Title bar 5 Status bar

2 Menu bar Provides helpful information.
Provides access to the functions. 6 Preview window
3 Toolbar Shows how the stitch pattern will be sewn.
Provides shortcuts for the menu commands. 7 Design Page
4 Tool Box The actual part of the work area that can be
Used to select and create fill and motif saved.
stitch patterns and stamps. 8 Work area
(The bottom four buttons do not appear in 9 Minimize button
Motif mode.) 10 Maximize button
11 Close button

34

PED7_QSG.indb Sec3:34 02.06.2006 20:07:14

 Understanding Windows and Using Tools

Design Database Window

1 18
2
3 17
16

4 15

5 14
6 13
7
8

9 12
10
11

1 Title bar 10 Remove button

2 Menu bar Returns the selected design (displayed in
Gives access to the functions. the writing list) to the unselected state.
3 Toolbar 11 Status bar
Provides shortcuts for the menu commands. Provides helpful information.
4 Folder pane 12 Writing list
Provides access to the folders on the com- The list of designs to be written to the origi-
puter and the results of any searches that nal card is displayed.
were performed. 13 Add button
5 Card reading button The design selected in the contents pane
Reads an original card. view is displayed in the writing list.
6 Folder content display button 14 Card writing box display/non-display
The folder pane and contents pane display button
are switched to the folder contents. Press when writing the design to an original
7 Hoop size selector card. Click this button to hide or display
This selects the hoop size when writing a the writing list.
pattern to an original card. 15 Contents pane
8 Card capacity indicator Displays thumbnails of all embroidery pat-
Displays the selected design (displayed terns in the selected folder.
in the writing list) for the capacity of the 16 Minimize button
original card. 17 Maximize button
9 Write button 18 Close button
The selected design (displayed in the writ-
ing list) is written to the original card.

35

PED7_QSG_05.indd Sec3:35 08.06.2006 10:43:06

 Automatically Converting an Image to an
Embroidery Design (Auto Punch Function)
In this section, we are going to use the Auto Punch function to automatically create an embroidery
pattern from an image.
This procedure will go through each step of the basic operation.

Step 1 Importing image data into Layout & Editing page 36

Step 2 Automatically converting the image to an embroidery pattern page 39

Step 3 Displaying a preview of the embroidery page 41

Step 4 Saving the embroidery design page 42

Step 5 Transferring the design to an original card page 44

Step 1: Importing image data into Layout & Editing

First, we need to import the image that will be converted into an embroidery pattern.
For this example, we will use the tulip image (tulip.bmp) provided with this application.

a Start up Layout & Editing.

Click , then, select All Programs,

then PE-DESIGN Ver7, then, Layout & Editing.

→ The Layout & Editing window appears.

36

PED7_QSG.indb Sec1:36 02.06.2006 20:07:15

 Automatically Converting an Image to an Embroidery Design (Auto Punch Function)

b Import the image. Memo:

• The default value for the Design
Page size in this example is 100 x
100 mm.
• You can change the Design Page
size by using the menu command
Click Image, then Input, then from File. Option-Design Page Property.

Double-click the ClipArt folder to open it.

Select the sample file tulip.bmp, and then click Open,

or double-click the file’s icon.

37

PED7_QSG.indb Sec1:37 02.06.2006 20:07:16

 → The image appears in the work area.

c Adjust the image size and position. Memo:

• The status bar shows the dimen-
sions (width and height) of the
image.
• The shape of the pointer changes to
, , , or , depend-
ing on the handle that the pointer
is over.
• is for scaling the width.
Handles
• is for scaling the height.

• and are for scaling both

dimensions at the same time. (The
height-to-width proportion is main-
tained.)
• If the key is held down while
a handle is dragged, the image is
enlarged or reduced in both width
Status bar and height from the center of the
image. (The height-to-width propor-
Drag the handle to adjust the selected image tion is maintained.)
to the desired size. • If the handles have disappeared,
right-click the image, and then click
Modify Image in the menu that ap-
peared.

38

PED7_QSG.indb Sec1:38 02.06.2006 20:07:17

 Automatically Converting an Image to an Embroidery Design (Auto Punch Function)

Move the pointer over the selected image, and then

drag the image to the desired position.

Step 2: Automatically converting the image to an

embroidery pattern
Next, the image will automatically be converted to an embroidery pattern.

a Select the conversion method.

Click Image, then Image to Stitch Wizard.

39

PED7_QSG.indb Sec1:39 02.06.2006 20:07:18

 Select Auto Punch, and then click Next.

b Convert the image to an embroidery pattern.

Check Result View tab to see the preview of the

conversion, and then click Finish.

40

PED7_QSG.indb Sec1:40 02.06.2006 20:07:18

 Automatically Converting an Image to an Embroidery Design (Auto Punch Function)

→ The generated embroidery pattern is displayed.

Step 3: Displaying a preview of the embroidery

Preview the finished embroidery.

Click Display, then Realistic Preview.

41

PED7_QSG.indb Sec1:41 02.06.2006 20:07:19

 To return to the normal view,
click Display, then Realistic
Preview, or click , or
press the key.

Step 4: Saving the embroidery design

Once the embroidery design is finished, you may want to save it in order to retrieve it later.

Click File, then Save.

42

PED7_QSG.indb Sec1:42 02.06.2006 20:07:20

 Automatically Converting an Image to an Embroidery Design (Auto Punch Function)

Select the drive and the folder, and then type in the
file name.

Click Save.

43

PED7_QSG.indb Sec1:43 02.06.2006 20:07:21

 Step 5: Transferring the design to an original card
By writing a design to a media that can be used in your embroidery machine and transferring it to
your embroidery machine, you can actually sew the design. For this example, we will transfer the
design to an original card.

Memo:
• You can also use Floppy Disks, Compact Flash Card, and USB Media to save designs.

a Insert an original card into the USB card Note:

writer module. • The original card is inserted cor-
rectly when you hear it snap into
place.

b Transfer the embroidery design.

Click File, then Write to Card.

44

PED7_QSG.indb Sec1:44 02.06.2006 20:07:21

 Automatically Converting an Image to an Embroidery Design (Auto Punch Function)

→ The following message appears.

Note:
• Before using the original card,
make sure that the designs on the
card are no longer needed or make
sure to store them on your hard
drive or other storage media.

Click OK.

→ The following message appears.

Note:
• If the card writer module is not
correctly connected or powered,
an error message of “No card
writer module is connected.Please
connect card writer module.” will
appear.
• If the original card is not inserted
or is defective, an error massage of
Click OK. “No original card is inserted. Please
insert an original card.” will appear.

c Quit Layout & Editing.

Click File, then Exit.

45

PED7_QSG.indb Sec1:45 02.06.2006 20:07:22

 Troubleshooting
If you have a problem, check the following solutions. If the solutions suggested do not correct the
problem, contact your authorized dealer or Brother Customer Service.

Problem Estimated Cause Solution Page

An operation not
described in the instal-
lation procedure was
performed. (For exam- Follow the instructions and cor-
12
ple, Cancel was clicked rectly perform the procedure.
The software is not installed or the CD-ROM was
correctly. removed before the pro-
cedure was completed.)
Refer to memo: “If the installer
The installer does not
does not automatically start 14
automatically start up.
up”.
If the opera-
tion described
When the USB connector is
at the left does
correctly plugged into the USB
not correct
The message “No card writer port, the installer for the driver
The driver for the USB the problem,
module is connected. Please of the USB card writer module
card writer module is not go to the Web
connect card writer module.” starts up.
installed correctly. site mentioned
appeared. For details, refer to “Installing
under “Techni-
the driver for the card writer
cal Support”.
module” on page 16.
(Refer to page
22.)

If the opera-
tion described
The message “Old version
at the left does
is not installed correctly.
not correct
Please install old version The installation informa- Uninstall the older version from
the problem,
before installing this updated tion for the old version the computer, install the older
go to the Web
program.” appears when the on the computer is not version again, and then perform
site mentioned
upgrade is being installed, working properly. the upgrade.
under “Techni-
even though an older version
cal Support”.
(version 5 or 6) is installed.
(Refer to page
22.)

When upgrading from ver-

sion 5.0 or 5.01, the installa-
The upgrade from ver- When the USB card writer
tion was completed correctly,
sion 5.0 or 5.01 was module is unplugged, then rep-
but the message “No card
performed with the USB lugged into the PC, the installer 16
writer module is connected.
card writer module con- for the driver of the USB card
Please connect card writer
nected. writer module starts up.
module.” appeared, and the
application does not start up.

46

PED7_QSG_06.indd Sec1:46 08.06.2006 10:43:54

 Troubleshooting

Problem Estimated Cause Solution Page

To upgrade the USB card writer

When trying to upgrade from
module, the computer with the
an older version, the message
The computer with the card writer module connected
“Cannot connect to the In-
USB card writer module to its USB port must connect to
ternet.” or “The server could
connected to its USB the Internet. If firewall soft-
not be connected to. Wait a 19
port could not establish ware is being used, it must be
while, and then try connect-
a connection to the temporarily disabled during the
ing again.” appeared and
Internet. upgrade. If a connection to the
the USB card writer module
Internet cannot be established,
could not be upgraded.
contact your authorized dealer.

Connect the USB card writer

module to a USB port on the
The USB card writer module Not enough power is be- computer or to a self-pow-
13
does not operate correctly. ing supplied. ered USB hub that can supply
enough power to the card
writer module.

47

PED7_QSG.indb Sec1:47 02.06.2006 20:07:23

 Read the following before opening the
CD-ROM package
Thank you for purchasing this software. Before opening the CD-ROM package for this software,
carefully read the following Product Agreement, which has been provided for this product. Use this
software only if you agree to the terms of this agreement. By opening the CD-ROM package, you
agree to the conditions of its use. This product cannot be returned after it has been opened.

Product Agreement

1) General terms
This is an agreement between you (the end-user) and our company for this product.
2) Use of this product
You may install and use this product on only one computer.
3) Limitations on duplications
You may not duplicate this product, except for backup purposes.
4) Limitations on modifications
You may not modify or disassemble this product in any way.
5) Limitations on transfer
This software may not be transferred to or used in any other way by a third party.
6) Warranty
We accept no responsibility for your choice or use of this product or for any damages that
may arise out of its use.
7) Others
This product is protected by copyright laws.

Portions of this product were created using technology from Softfoundry International Pte. Ltd.

PED7_QSG.indb 49 02.06.2006 20:07:23