Protein Electrophoresis: Technical Manual

tech nical manual
protein electrophoresis
Protein Electrophoresis
technical manual
tm 80-6013-88/Rev. B0/12-99
• page finder
Page finder
This technical manual contains information Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii
that has been distilled from more than 30
years of laboratory experience in developing
Chapter 1
and verifying applications and product perfor- Introduction to Electrophoretic Theory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
mance for protein electrophoresis. As such it 1.0 Principles of electrophoresis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.1 Electrical parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
is ideal for both new and current users of
1.2 Buffers and pH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
protein electrophoresis as both a teaching and
1.3 Effects of heat on separations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
a reference guide. The first chapter provides
1.4 Matrix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
a theoretical framework, and Chapters 2
1.4.1 Agarose gels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
through 4 cover the major aspects of protein 1.4.2 Polyacrylamide gels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
electrophoretic separation: polyacrylamide gel 1.5 Analysis of the results . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
electrophoresis, isoelectric focusing, and gel 1.5.1 Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
analysis. In addition, an extensive reference 1.5.2 Quantification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
list is summarized at the end of every chap- 1.6 Blotting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
ter, and a detailed glossary is included at the 1.6.1 Transfer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
end of the manual. 1.6.2 Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
1.7 Protocols in this manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
1.8 References and bibliography . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Chapter 2
Polyacrylamide Gel Electrophoresis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2.1 Equipment choices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2.2 Separating proteins on the basis of molecular weight:
SDS gel electrophoresis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2.2.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2.2.2 Stock solutions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
2.2.3 Materials and equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
2.2.4 Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
2.3 Separating proteins on denaturing mini-gels . . . . . . . . . . . . . . . . . . 23
2.3.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
2.3.3 Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
2.4 Preparing linear gradient gels . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
2.4.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
2.4.3 Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
2.5 Native gel electrophoresis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
2.6 Separating proteins by flatbed SDS-PAGE . . . . . . . . . . . . . . . . . . . . 36
2.6.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
2.6.3 Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
2.7 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
2.8 References and bibliography . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
•i
protein electrophoresis • page finder
Chapter 3
Isoelectric focusing of proteins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
3.0 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
3.1 Native isoelectric focusing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
3.1.1 Solutions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
3.1.3 Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
3.2 Denaturing isoelectric focusing . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
3.2.1 Solutions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
3.2.3 Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
3.3 Isoelectric focusing using immobilized pH gradient (IPG) gels . . . . . . 50
3.3.2 Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Chapter 4
Analysis of gels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
4.1 Staining Gels with Coomassie Brilliant Blue . . . . . . . . . . . . . . . . . . 55
4.1.1 Coomassie Blue staining stock solutions . . . . . . . . . . . . . . . . 56
4.1.3 Standard Coomassie Blue protocol . . . . . . . . . . . . . . . . . . . . 57
4.1.4 Automated Coomassie Blue staining . . . . . . . . . . . . . . . . . . . 58
4.2 Silver Staining . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
4.2.1 Silver staining stock solutions . . . . . . . . . . . . . . . . . . . . . . . 59
4.2.3 Silver staining protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
4.3 Gel drying and storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
4.3.1 Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
4.3.2 Drying gels by vacuum . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
4.3.3 Air drying using Easy Breeze . . . . . . . . . . . . . . . . . . . . . . . . 61
4.4 Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
4.4.1 Photography . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
4.4.2 Densitometer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
4.4.3 Scanners and digital cameras . . . . . . . . . . . . . . . . . . . . . . . 62
4.5 Estimation of protein molecular weights by SDS gel electrophoresis . . 62
4.5.2 Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
t m 80-6013-88 • ii
• safety
Safety
Safety considerations are important during the preparation and execution
of these laboratory experiments. Chemical and electrical hazards, two prin-
cipal areas specifically related to electrophoresis, are discussed below. For
full information concerning the safety and hazardous materials handling
practices of your institution, contact your health and safety officer.
Chemical safety
Some of the chemicals used in these procedures are hazardous. Acry-
lamide monomer, for example, is a neurotoxin and suspected carcinogen.
You should have a manufacturer’s safety data sheet (MSDS) detailing
the properties and precautions for all chemicals in your lab. The safety
sheets should be reviewed prior to starting the procedures in this manual.
General handling procedures include using double latex gloves for all
protocols and weighing hazardous materials in a hood while wearing a
disposable dust mask.
Electrical safety
The voltage and current used in these exercises are potentially lethal.
The following items should be checked prior to initiating any experiment
in electrophoresis.
• Work area. The bench and floor should be dry.
• High-voltage connections. The high-voltage leads should be intact and

not frayed. The plug should have a protective plastic sleeve that shields
the plug as it is inserted into the power supply. Exposed plugs are a
shock hazard and should be replaced with shielded plugs. Stackable
leads that connect more than one gel unit to a single outlet are not
recommended and should be replaced with shielded-style plugs.
• Electrophoresis chambers. These should be covered when in use, with

no openings large enough to allow fingers or other objects to make
contact with the electrified buffer or electrodes.
• Power supplies. All newer power supplies have deeply recessed outputs
that minimize the possibility of contacting the electrically active plug or
high-voltage input jacks. Older power supplies do not have recessed
jacks and, when used in combination with old-style banana plugs, pose
a serious shock hazard and require special caution to use. Without the
protection of the shield, a researcher can make contact with the plug
while it is still connected to the power supply and receive a potentially
lethal shock.
continued on following page
• iii
protein electrophoresis • safety
The following power connection protocol should minimize these hazards

and is recommended for all power supplies:
• Start with power supply off and with voltage and current controls
set at zero.
• Connect the gel box and leads to power supply.
Caution. When connecting high-voltage leads to the power supply, use

your right hand only. Because of the potential for lethal shock across the
chest do not use both hands to plug in (or unplug!) power supply leads.
Also, make sure your left hand is not touching anything that would
ground you.
• Turn on the power supply and set for the desired current or voltage.
• At the end of the run, turn the voltage and current to zero and then
turn off the power supply at the AC mains.
Caution.Power supplies have internal capacitance that stores electrical

charge even after the power supply is turned off. This stored charge can
deliver a potentially lethal shock should the operator come in contact
with the positive and negative output. Bringing the voltage and current
display to zero indicates the power supply can be safely turned off.
• Unplug the high-voltage leads using your right hand only.
t m 80-6013-88 • iv
• introduction to electrophoretic theory
Chapter 1
Introduction to electrophoretic theory
1.0 Principles of electrophoresis

Electrophoresis is the process of moving charged molecules in solution by
power supply
applying an electric field across the mixture (Fig 1.1). Because molecules in
an electric field move with a speed dependent on their charge, shape, and
size, electrophoresis has been extensively developed for molecular separa-
tions. As an analytical tool, electrophoresis is simple and relatively rapid.
electrodes
It is used chiefly for analysis and purification of very large molecules such
as proteins and nucleic acids, but can also be applied to simpler charged
molecules, including charged sugars, amino acids, peptides, nucleotides,
and simple ions. Highly sensitive detection methods have been developed
Fig 1.1. Basic arrangement for electrophoresis.
to monitor and analyze electrophoretic separations.
Electrophoresis of macromolecules is normally carried out by applying a

thin layer of a sample to a solution stabilized by a porous matrix. Under the
influence of an applied voltage, different species of molecules in the sample
move through the matrix at different velocities. At the end of the separa-
tion, the different species are detected as bands at different positions in the
matrix. A matrix is required because the electric current passing through the
electrophoresis solution generates heat, which causes diffusion and convec-
tive mixing of the bands in the absence of a stabilizing medium. The matrix
can be composed of a number of different materials, including paper, cellu-
lose acetate, or gels made of polyacrylamide, agarose, or starch. In acry-
lamide and agarose gels, the matrix also acts as a size-selective sieve in the
separation. At the end of the run, the separated molecules can be detected in
position in the gel by staining or autoradiography, quantified by scanning
with a densitometer, and the gel can be dried for permanent storage.
Polyacrylamide and agarose gels (Fig 1.2) are the most common stabiliz-
acrylamide ing media used in research laboratories. The gels are usually formed as
O
ll cylinders in tubes, or as thin, flat slabs or sheets. Polyacrylamide is the
H2C = CH C NH2
- -
most common matrix for separating proteins. Nucleic acids are separated
agarose on either polyacrylamide or agarose gels, depending on the sizes of mole-
cules to be analyzed. The choice of matrix and concentration effects on
size separation are discussed further in section 1.4.
In most electrophoresis units, the gel is mounted between two buffer

chambers in such a way that the only electrical connection between the
Fig 1.2. Chemical structure of acrylamide
and agarose. two chambers is through the gel. Contact between the buffer and gel may
be direct liquid contact (Fig 1.3a–c) or through a wick or pad of paper or
gel material (Fig 1.3d). Although vertical tube and slab gels (Fig 1.3a–b),
which have direct liquid buffer connections, make the most efficient use
of the electric field, the apparatus presents some mechanical difficulties in
equipment design: The connections must be liquidtight, electrically safe
• p1
protein electrophoresis • introduction to electrophoretic theory
and convenient to use. The search for convenience has led to several
alternative methods for connecting buffer and gel. Paper or gel wicks
A B connecting the reservoir to the gel were early designs that are used only
rarely now. “Submarine gels” are run in a horizontal orientation with the
gel resting on a platform between the buffer reservoirs, submerged under
a layer of a few millimeters of buffer (Fig 1.3c). For other horizontal
applications, the buffer reservoir has been reduced to a moist pad of
buffer-saturated paper or gel material that serves as a contact bridge
between the electrodes and the separation gel (Fig 1.3d).
Gels can be of all sizes, depending on the separation distance needed and
C the amount of sample. Analytical tube gels are commonly cast in glass
tubes with an inside diameter of 1–5 mm and a length of 5–25 cm.
Preparative tube gels may range up to 10 cm in diameter to accommodate
larger amounts of material. At the other extreme, gels run in capillaries
50–100 µm in diameter and 30–100 cm long provide very high resolution
D and rapid separations of very small amounts of sample.
Vertical slab gels are normally cast between a pair of glass plates for
support. A chamber is constructed by separating the two plates with spacer
Fig 1.3. Cross-section diagrams of gel apparatus strips down the edges of the plates, then sealing the edges and bottom to
designs: (A) tube, (B) vertical slab, (C) horizontal
form a liquidtight box or “sandwich” (Fig 1.4). Slab gels range in size from
submarine, (D) horizontal thin layer with buffer pads.
2.5 cm square (between microscope coverslips) to 30 × 150 cm square and
from <0.05 mm to >5 mm thick.
Horizontal acrylamide gels, like vertical slabs, must be polymerized between

spacer plates, because the acrylamide polymerization is oxygen sensitive. After poly-
sample well comb
merization one glass plate is removed to expose the gel surface. In contrast,
horizontal agarose gels may be cast simply by pouring molten agarose onto a
glass or plastic plate. Horizontal gels range in size from 2.5 × 5 cm square to
20 × 30 cm square and from <0.05 mm to >10 mm thick.
1.1 Electrical parameters

The fundamental driving force of electrophoresis is the voltage applied
to the system. The speed of a molecule is directly proportional to the
glass plates
surrounding voltage gradient. Two basic electrical equations are impor-
spacer tant in electrophoresis. The first is Ohm’s Law:
Fig 1.4. Diagram of vertical slab gel assembly V = IR or I = V (eq 1)

R
(“sandwich”). The sides and bottom must be
sealed liquidtight when the gel is cast. Ohm’s Law relates voltage (V) measured in volts (V), current (I)
measured in amperes (A), and resistance (R) measured in ohms (Ω). The
second fundamental equation in electrophoresis is the power equation,
which describes the amount of heat produced in a circuit. It can be writ-
ten in several forms:
2
P = VI or P = I2R or P = V (eq 2)
R
where P is power, which is measured in watts (W). This heat is also
referred to as Joule heat. In the electrophoresis circuit, voltage and
current are supplied by a DC power supply; the leads, electrodes, buffer,
and gel all act as simple resistors.
t m 80-6013-88 • p2
Power supplies used for electrophoresis hold one electrical parameter

(current, voltage, or power) constant. The resistance of the electrophoresis
circuit, however, does not remain constant during a run. Buffer resistance
declines with increasing temperature caused by Joule heating. Resistance
also changes as discontinuous buffer ion fronts move through a gel; in the
case of discontinuous denaturing polyacrylamide gel electrophoresis
(SDS-PAGE), resistance increases as the run progresses. Depending on the
buffer and which electrical parameter is held constant, the Joule heating
of the gel may increase or decrease over the period of the run.
Table 1.1. Effect of power supply Table 1.1 illustrates the change in P (and temperature) observed under
mode on heat generation different electrophoresis conditions. For discontinuous SDS-PAGE, running
at constant current leads to increasing heat generation and may require
Power
Buffer supply active heat removal. By contrast, continuous buffer systems, such as those
system Change constant used in electrophoretic blotting or DNA gels, will tend to overheat when
effect during run mode Heat
run at constant voltage. Whenever overheating is a potential problem, a
Discontinuous ↑R current (Ic) ↑P method of heat removal should be supplied (a circulating thermostatted
(SDS-PAGE) voltage (Vc) ↓P
bath or cold tap water) or low voltage/current conditions should be applied
Continuous ↓R current (Ic) ↓P to prevent heat-induced artifacts or damage to the instrument.
(Blotting, DNA) voltage (Vc) ↑P
The choice of the power supply constant mode for an electrophoresis
experiment must include consideration of several variables, including the
time available, the need to minimize sample diffusion and loss of sample
activity caused by either heat or time, and the need to maintain a specific
temperature for the run. Conventionally, protein gels are run at constant
current, nucleic acid separations are performed at constant voltage, and
DNA sequencing gels are run under constant power conditions. Most
protein isoelectric focusing experiments use constant power because the
resistance of the gel becomes very high as the separation nears completion.
1. 2 Buffers and pH
Proteins are amphoteric (or zwitterionic) compounds and are therefore
either positively or negatively charged because they contain both acidic
and basic residues. Nucleic acids are not amphoteric and remain nega-
tively charged at the pH used for most electrophoresis buffers because
of the strong acid nature of the phosphate groups in the backbone.
Most of the charge of a protein comes from the pH-dependent ioniza-

tion of amino acid side-chain carboxyl and amino groups (–COOH ↔
COO– + H+; –NH2 + H+ ↔ NH3+). Histidine, a weakly basic amino
acid, also contributes to the charge. Because these groups can be titrated
over normal electrophoresis pH ranges, the net charge of a protein is
determined by the pH of the surrounding medium and the number and
types of amino acids carrying amino or carboxyl groups. Post-transla-
tional modifications such as the addition of charged and uncharged
sugars, sulphydryl cross-links, and blocking amino or carboxyl termini,
also may alter the charge on a protein.
• p3
For each protein species, there is a pH at which the molecule has no net
charge. At this pH, called the isoelectric point or pI, the weak acids and
bases are titrated to the point that there is an equal number of positive
and negative charges on the molecule. Each protein has a unique pI. For
example, the pI of human hemoglobin is at pH 7.07; that of β-lactoglo-
bin is at pH 5.34. In a solution with a pH above the isoelectric point, a
protein has a net negative charge and migrates toward the positive elec-
trode (anode) in an electric field. When in a solution below a protein’s
isoelectric point, the protein charge is positive and migrates toward the
negative electrode (cathode).
For electrophoretic protein separations based on the mobility of the differ-

ent species, the pH of the solution must be kept constant to maintain the
charge and, hence, the mobilities of the proteins. Therefore, because elec-
trolysis of water generates H+ at the anode and OH– at the cathode, the
solutions used in electrophoresis must be buffered. On the other hand, the
pH-dependent mobility of proteins can be used to separate them by their
isoelectric points in another separation technique called isoelectric focusing
(IEF). In IEF proteins are electrophoresed into a pH gradient. As the
proteins move through the gradient, they encounter a point where the pH
is equal to their pI and they stop migrating. Because of differences in pI,
different proteins will stop (“focus”) at different points in the gradient.
1.3 Effects of heat on separations

Temperature regulation is critical at every stage of electrophoresis if
reproducibility is important. For example, acrylamide polymerization
is an exothermic reaction, and during polymerization—particularly of
high-concentration gels—the heat of polymerization may cause convec-
tion flows that lead to irregularities in the sieving pore sizes of the gel.
Convection is not usually a problem for gels of <15%T.
Heat can cause a number of problems during electrophoresis:
• Excessive heat can cause agarose gels to melt, glass plates to break, or
damage to the electrophoresis unit.
• When separating native proteins by electrophoresis, the Joule heat must

be controlled, either by active cooling or by running the gel at low
voltages, to prevent heat denaturation or inactivation of the proteins.
• Nonuniform heat distribution distorts band shapes due to different

mobilities at different temperatures. Slab gels are described as “smiling”
when the samples in the center lanes move faster than samples in the
outer lanes. This effect is due to more-rapid heat loss from the edges of
the gel than from the center. Bands may appear as doublets or broader
than expected when the front and rear vertical glass plates or the top
and bottom of a horizontal slab are at different temperatures.
Recognizing and dealing with these problems is covered more thoroughly

in the troubleshooting sections of this guide.
t m 80-6013-88 • p4
To maintain acceptable temperature control and uniformity throughout

the gel and the run, the electrophoresis equipment must be designed for
efficient heat transfer. The unit must provide good contact between the
gel and a heat sink, and between the heat sink and a heat exchanger. A
proven design for vertical slab and tube gel units uses the buffer as a heat
sink. When most of the length of the gel tube or slab assembly makes
contact with the buffer, heat is transferred quickly and uniformly out
of the gel. A heat exchanger in contact with the buffer then transfers
the heat to an external coolant. Many DNA sequencing units use an
aluminum plate in contact with one side of the slab assembly to distrib-
ute heat evenly across the gel and reduce smiling. Sequencing units
normally do not require cooling, because they are intentionally run at
40–60 ºC. Horizontal slab gels may be cast directly on the surface of a
heat exchanger. Some electrophoresis unit designs require that the buffer
be pumped through an external loop to a refrigerated bath. This type of
design poses an electrical hazard if the pump or tubing develops a leak.
1.4 Matrix
Agarose and polyacrylamide gels are cross-linked, spongelike structures.
Although they are up to 99.5% water, the size of the pores of these gels
is similar to the sizes of many proteins and nucleic acids. As molecules
are forced through the gel by the applied voltage, larger molecules are
retarded by the gel more than are smaller molecules. For any particular
gel, molecules smaller than a matrix-determined size are not retarded at
all; they move almost as if in free solution. At the other extreme, mole-
cules larger than a matrix-determined size cannot enter the gel at all. Gels
can be tailored to sieve molecules of a wide range of sizes by appropriate
choice of matrix concentration. The average pore size of a gel is deter-
mined by the percentage of solids in the gel and, for polyacrylamide, the
amount of cross-linker and total amount of polyacrylamide used.
Polyacrylamide, which makes a small-pore gel, is used to separate most

proteins, ranging in molecular weight from <5 000 to >200 000, and
polynucleotides from <5 bases up to ~2 000 base pairs in size. Because
the pores of an agarose gel are large, agarose is used to separate macro-
molecules such as nucleic acids, large proteins, and protein complexes.
Various types of agarose can separate nucleic acids from 50 to 30 000
base pairs and, with pulsed-field techniques, up to chromosome- and
similar-sized pieces >5 × 106 base pairs long.
Whichever matrix is selected, it is important that it be electrically

neutral. Charged matrices may interact chromatographically with mole-
cules and retard migration. The presence of fixed charged groups on the
matrix will also cause the flow of water toward one or the other elec-
trode, usually the cathode. This phenomenon, called electroendosmosis
(often abbreviated EEO in supplier literature), usually decreases the
resolution of the separation.
• p5
1.4.1 Agarose gels

Agarose can be used for isoelectric focusing and separation of large
proteins or protein complexes. Agarose is a highly purified polysaccharide
derived from agar. For protein IEF applications, the critical qualities are
low EEO and good clarity at the working concentration. When used in a
thin horizontal format for IEF, agarose gels must be supported on a plas-
tic backing and cooled during electrophoresis.
Agarose is normally purchased as a dry powder. It dissolves when the

suspended powder is heated to near boiling and it remains liquid until the
temperature drops to about 40 ºC, when it gels or “sets.” There are specific
types of agarose that have melting and gelling temperatures considerably
lower than those of standard agarose. These properties improve the recov-
ery of material from a gel after separation for subsequent enzymatic treat-
ments of the separated material.
The pore size and sieving characteristics of a gel are determined by

adjusting the concentration of agarose in the gel. The higher the concen-
tration, the smaller the pore size. Working concentrations are normally
A B in the range of 0.4–4% w/v.
Agarose gels are relatively fragile and should be handled carefully. The
Fig 1.5. Agarose and acrylamide gels. (A) Agarose
gels are hydrocolloids, held together by hydrogen and hydrophobic bonds,
gels form by noncovalent hydrogen and hydrophobic
bonds between long sugar polymers. (B) Acrylamide and tend to be somewhat brittle (Fig 1.5a). An agarose gel should always
gels have covalent cross-links (•) between polymer be handled with some form of support for the entire gel, such as a tray or
strands.
wide spatula, because the gel will break if it bends too far.
1.4.2 Polyacrylamide gels

Polyacrylamide gels are physically tougher than agarose gels. The gel
forms when a mixed solution of acrylamide and cross-linker monomers
co-polymerize into long chains that are covalently cross-linked. The gel
structure is held together by the cross-linker (Fig 1.5b). The most common
cross-linker is N,N'-methylenebisacrylamide (“bis” for short). Other
cross-linkers that can be cleaved after polymerization are available (e.g.
N,N'-bis-[acryloyl]-cystamine can be cleaved by disulphide reducing
agents); they aid in recovering separated species from the gel by allowing
the polymerized acrylamide to be solubilized.
Because polymerization of acrylamide is a free-radical catalyzed reaction,

preparation of polyacrylamide gels is somewhat more complex than that
of agarose gels. Some of the technical issues are discussed in the follow-
ing sections.
Preparing and pouring the monomer solution
Atmospheric oxygen is a free-radical scavenger that can inhibit polymer-

ization. For consistent results the acrylamide monomer solution is
deaerated by purging it with an inert gas or by exposing it to a vacuum
for a few minutes. Preparing solutions with a minimum of stirring, which
introduces air, will reduce oxygen inhibition problems.
t m 80-6013-88 • p6
When the gel solution is poured into a tube or slab mold, the top of the
solution forms a meniscus. If the meniscus is ignored, the gel will polymer-
ize with a curved top, which will cause the separated sample bands to
have a similar curved pattern. To eliminate the meniscus, a thin layer of
water, buffer, or water-saturated n-butanol is carefully layered on the
surface of the gel mixture before it polymerizes (Fig 1.6). After polymer-
ization the water or butanol layer is poured off, leaving the upper surface
of the gel flat. The layer of water or water-saturated butanol also excludes
oxygen, which would otherwise inhibit polymerization on the gel surface.
Alternatively, a flat-edged form, such as a comb, can be inserted into the

top of the solution to give a mechanically flat surface. Care must be taken
Fig 1.6. Meniscus effect on gel shape. Overlaying
the gel mix with water or n-butanol gives a flat gel not to trap small air bubbles under the bottom edge of a comb. Combs
surface for flat sample bands. made of Teflon will inhibit polymerization of a thin layer immediately
next to the comb, because of oxygen dissolved in the plastic of the comb.
This unpolymerized layer is convenient because it eases removing the
comb without affecting the performance of the gel.
Determining the pore size
The size of the pores in a polyacrylamide gel is determined by two parame-

g(acrylamide + bisacrylamide) ters: total solids content (%T) and the ratio of cross-linker to acrylamide
%T= × 100
100 ml monomer (%C) (Fig 1.7). The %T is the ratio of the sum of the weights of
the acrylamide monomer and the cross-linker in the solution, expressed as
g(bisacrylamide)
%C= × 100 % w/v. For example, a 20%T gel would contain 20% w/v of acrylamide
g(acrylamide + bisacrylamide)
plus bisacrylamide. As the %T increases, the pore size decreases.
Fig 1.7. Determination of %T and %C for The second way to adjust pore size is to vary the amount of cross-linker.
acrylamide gels.
The %C is the weight/weight percentage of total cross-linker weight in
the sum of monomer and cross-linker weights. Thus, a 20%T 5%Cbis gel
would have 20% w/v of acrylamide plus bis, and the bis would account
for 5% of the total solids weight (acrylamide plus bis). Occasionally, gel
compositions are given as ratios of acrylamide to cross-linker (such as
19:1 for the 20%T 5%C mixture). It has been found that for any single
%T, 5% cross-linking creates the smallest pores in a gel. Above and
below 5%, the pore size increases.
If the material under study is a mixture with species having a wide range
of molecular weights, you may want to use a pore-gradient gel. In these
gels the pore size is larger at the top of the gel than at the bottom; the gel
becomes more restrictive as the run progresses. The presence of the gradi-
ent yields a gel with a wider range of size resolution and also keeps bands
tighter than in uniform-concentration gels.
Polymerizing the gel
The free-radical vinyl polymerization of acrylamide gel can be initiated

either by a chemical peroxide or by a photochemical method. The most
common method uses ammonium persulphate as the initiator peroxide
and the quaternary amine, N,N,N',N'-tetramethylethylenediamine
(TEMED) as the catalyst.
• p7
For photochemical polymerization, riboflavin and long-wave UV light

are the initiator, and TEMED is the catalyst. Shining long-wavelength
ultraviolet light on the gel mixture, usually from a fluorescent light,
starts the photochemical reaction. Photochemical polymerization is used
when the ionic strength in the gel must be very low, because only a
minute amount of riboflavin is required. It is also used if the protein
studied is sensitive to ammonium persulphate or the by-products of
peroxide-initiated polymerization.
Polymerization of acrylamide generates heat. Rapid polymerization can

generate too much heat, causing convection inconsistencies in the gel
structure and occasionally breaking glass plates. It is a particular problem
for high-concentration gels (>20%T). To prevent excessive heating, the
concentration of initiator-catalyst reagents should be adjusted so that
complete polymerization requires 20–60 min.
1.5 Analysis of the results

1.5.1 Detection
After the electrophoresis run is complete, the gel must be analyzed quali-
tatively or quantitatively to answer analytical or experimental questions.
Because most proteins and all nucleic acids are not directly visible, the
gel must be processed to determine the location and amount of the
separated molecules.
The most common analytical procedure is staining. Proteins are usually

stained with Coomassie™ Brilliant Blue in a fixative solution or, after fixa-
tion, with silver by a photographic-type development. With Coomassie
Blue staining, about 0.1–0.3 µg of protein is the lower detectable limit in
a band, and even less for some proteins. The silver staining systems are
about 100 times more sensitive, with a lower detection limit of about
1 ng of protein. Once the gel is stained, it can be photographed, scanned,
or dried on a transparent backing or filter paper for a record of the posi-
tion and intensity of each band.
Nucleic acids are usually stained with ethidium bromide, a dye that fluo-
resces weakly in free solution but exhibits strong orange fluorescence
when bound to nucleic acids and excited by UV light. About 10–50 ng
of double-stranded DNA can be detected with ethidium bromide on a
300 nm UV transilluminator. Fluorescent gels must be photographed
for a record of the separation.
Radioactively labelled samples separated on a slab gel are commonly

detected by autoradiography. The gel is first dried to a sheet of filter paper
and then placed in contact with X-ray film. The beta or gamma particles
emitted in a radioactive decay event expose the film the same way light or
X-rays do. After standard photographic development, the bands or spots
seen on the film correspond to the bands or spots in the gel. The resulting
autoradiograph is a permanent record of the results of the separation.
t m 80-6013-88 • p8
1.5.2 Quantification
Amount
Qualitative analysis of gels for the presence or absence of a band or

spot or relative mobilities of two bands can easily be performed by
visual inspection. Answering “How much?” and “What size?” questions
requires additional work. The amount of material in a band can be
determined to various levels of accuracy by a number of methods. The
simplest is to visually compare the intensity of a band, either stained
or autoradiographic, to standards of known quantity on the same gel.
More-accurate answers can be determined by using a densitometer to
scan the stained gel or photograph/autoradiograph of the gel. As gel
documentation systems have become increasingly available in laborato-
ries, electronic acquisition of data (video cameras, desktop scanners) is
replacing photographs. Image analysis software allows easy and rapid
analysis of separated proteins, including automatic calculation of
amount and molecular weight. Traditional methods of quantification
of radioactive bands by excision and scintillation counting has largely
been replaced by the use of radioanalytical devices that directly scan and
quantify the signals from radioactive gel bands. Native enzymes can be
excised and assayed by their standard assay. For quantitative analysis it
is always advisable to have known standards as controls for staining
efficiency, film nonlinearity, or recovery yields.
Size
Determining the size of a macromolecule by its mobility also requires

standards of known size for comparison. Because shape affects the
mobility of a molecule through a sieving gel, all the molecules in one gel
must have similar shapes for valid comparisons. This does not present
a problem for double-stranded DNA, because the shape of the molecules
is virtually sequence-independent. Single-stranded nucleic acids and
proteins, however, must be denatured to ensure similar random coil
shapes. For RNA or single-stranded DNA, denaturants added to the
buffer may include formamide, urea, formaldehyde, or methylmercury
hydroxide. Nucleic acids can also be denatured by treatment with
glyoxal before electrophoresis.
Proteins can be denatured with urea or sodium dodecylsulphate (SDS).

SDS denatures proteins by forming a stable complex that removes most
native folded structure. The amount of SDS in the complex depends only
on the size of the protein, not on charge or sequence. The strong negative
charge of the SDS molecules in the complex masks any pI differences that
might affect electrophoretic mobility. The resulting protein/SDS complex
is a random coil that has a negative charge dependent on the size of the
protein, not on its sequence.
Both protein and nucleic acid size standards are available commercially.
These standards are sets of well-characterized molecules that can be run in
lanes adjoining experimental samples for size comparison. Approximate
• p9
sizes of unknown species can be estimated by visual comparison to the

standard. For more-accurate estimates, standard band mobilities are used
to generate a calibration curve, then unknown sizes are read off of the
curve. Because the sizes of molecules are not a simple function of distance
moved through a gel, the best estimates of unknown sizes require having
several standards both smaller and larger than the molecule of interest.
1000
Plots of DNA molecule length (in base pairs) as a function of distance are
500 shown in Figure 1.8. For comparison, protein molecular weight plots are
400
shown in Figures 4.9 through 4.11.
300
Isoelectric point
200
As discussed, electrophoresing amphoteric molecules through a pH gra-
dient results in isoelectric focusing; the molecules stop at the pH equal
to their pI. The pI of an unknown protein can be estimated quickly by
A 100 comparing it with standards with known pIs, as described for sizing in
the preceding section. If the pH gradient is formed using soluble buffering
species (ampholytes), the pH of the gel can be measured at desired points
800
along the surface, using a pH electrode designed for use on moist surfaces.
600
size (base pairs)
1.6 Blotting
400
1.6.1 Transfer
200
For analysis based on antibody reactivity, the separated molecules need
0 to be free of the electrophoresis matrix. This can be done by slicing the
20 60 100 140
distance (mm)
gel into segments and then eluting the sample into a buffer, but the
B process is slow and the resolution is low. A more efficient method uses a
“blotting” technique. In blotting, the molecules separated on a slab gel
are eluted through the broad face of the gel onto a membrane filter that
3.00
binds the molecules as they emerge. The proteins (or nucleic acids) stay
2.75 predominantly on the surface of the membrane, where they are accessi-
log (size [base pairs])
ble for detection.

2.50
The membrane materials used most frequently in blotting are nitrocellu-

2.25
lose, various forms of modified and unmodified nylon, and polyvinylidene
2.00 difluoride (PVDF). The choice of membrane depends on the type of
analysis and characteristics of the detection system. Nitrocellulose is the
20 60 100 140
distance (mm)
most generally applicable; some nylons do not bind protein reliably.
C PVDF is often used when the bound protein will ultimately be analyzed
Fig 1.8. Analyzing gels for size information. by automated solid-phase protein sequencing.
(A) Acrylamide DNA gel. (B) Plot of size (bp)
versus distance migrated. (C) Plot of log (size The transfer of the sample from the gel to the membrane can be driven
[bp]) versus distance. either by capillary flow of buffer or by transverse electrophoresis. The use
of capillary flow to transfer DNA from agarose gels to nitrocellulose was
first described by Southern (1975), hence the name Southern blot. Using
the same method for transfer of RNA is called Northern blotting, and
any blot transfer of proteins is called Western blotting for simple playful
consistency of nomenclature.
t m 80-6013-88 • p10
Transferring separated molecules electrophoretically is generally faster

than capillary action, taking from 0.5 to 2 h. The gel containing sepa-
rated proteins is placed next to a membrane in a cassette, which is
electrodes
A then suspended in a tank of buffer between two electrodes. Applying a
plastic voltage to the electrodes moves the molecules out of the gel and onto
transfer the membrane (Fig 1.9a). The tank of buffer can be replaced by buffer-
cassette
wetted pads of filter paper for “semidry” blotting (Fig 1.9b).
membrane
1.6.2 Detection
gel
After transfer, proteins attached to the membrane can be detected either
filter
specifically with antibodies, or nonspecifically with various staining tech-
paper
niques. Highly sensitive nonradioactive immunodetection systems are
available that locate the sites of specific antibody binding by chromogenic,
fluorogenic, or chemiluminescent methods.
B filter electrodes
paper The results of the blot detection procedure can be analyzed as described
gel previously for stained gels to extract quantitative information on size or
amount of the detected target. Because an antibody detection system may
membrane
not reveal any standards on the gel, however, it is sometimes necessary
filter to use a staining method in addition to the specific probes for complete
paper analysis. Prestained standard markers may be used or blotted protein
standards can be visualized directly on the membrane by staining the
Fig 1.9. Electrophoretic blotting systems. Typically,
membrane with Ponceau S. The position of the Ponceau S–stained bands
these systems are used for electrophoretic transfer
of proteins out of polyacrylamide gels. (A) Tank must be marked with a permanent marker, as the dye washes out during
transfer. (B) Semidry transfer. the detection procedure.
1.7 Protocols in this manual

The following chapters of this manual describe SDS and native polyacry-
lamide electrophoresis, isoelectric focusing, and post-electrophoresis
protein detection and gel analysis. The protocols in each chapter are
examples of some of the most commonly used electrophoretic procedures
and techniques for proteins. They are presented step-by-step so that a
newcomer to electrophoresis can easily perform a separation or analysis
with no additional reading or instruction.
1.8 References and bibliography

Andrews, A. T. Electrophoresis: Theory, Techniques and Biochemical and
Clinical Applications, Oxford University Press, New York (1986).
Ausubel, F. M., et al., eds. Current Protocols in Molecular Biology,

Wiley-Interscience, New York (1995).
Hames, B. D., ed., Gel Electrophoresis of Proteins: A Practical Approach

3rd ed., Oxford University Press, New York (1998).
Southern, E. M. Detection of specific sequences among DNA fragments

separated by gel electrophoresis. J. Mol. Biol. 98, 503–517 (1975).
• p11
tm 80-6013-88 • p12
• polyacrylamide gel electrophoresis
Chapter 2
Polyacrylamide gel electrophoresis

This chapter describes polyacrylamide gel electrophoresis of protein
samples under denaturing and native conditions.
2.1 Equipment choices

There are many equipment options available for running polyacrylamide
gels, each with characteristics particularly adapted to a limited set of
applications. Choices include gel size and thickness, vertical or horizontal
orientation, precast or lab-cast gels, speed and resolution requirements,
application target, and cost considerations. Table 2.1 lists the instruments
available from Amersham Pharmacia Biotech with features for each.
Table 2.2 lists some of the parameters to consider when choosing a system.
Separations may be performed in a vertical or a flatbed system. Vertical

systems are widely used and offer a great deal of flexibility with acces-
sories. With simple casting units, gels can be poured with a choice of
buffers in a variety of thicknesses to accommodate various sample types
and sizes in both mini- and standard gel formats.
Horizontal flatbed systems using ultrathin gels polymerized on support

films offer advantages over vertical systems: more-secure gel handling,
convenience of ready-made gels and buffer strips that eliminate the need
for large volumes of buffer, good cooling efficiency, automation, and the
possibility of washing, drying, and rehydrating the gels.
2.2 Separating proteins on the basis of

molecular weight: SDS gel electrophoresis
2.2.1 Introduction
In SDS polyacrylamide gel electrophoresis (SDS-PAGE) separations,
migration is determined not by intrinsic electric charge of polypeptides
but by molecular weight. Sodium dodecylsulphate (SDS) is an anionic
detergent that denatures proteins by wrapping the hydrophobic tail
around the polypeptide backbone. For almost all proteins, SDS binds at
a ratio of approximately 1.4 g SDS per gram of protein, thus conferring
a net negative charge to the polypeptide in proportion to its length.
The SDS also disrupts hydrogen bonds, blocks hydrophobic interactions,
and substantially unfolds the protein molecules, minimizing differences
in molecular form by eliminating the tertiary and secondary structures.
The proteins can be totally unfolded when a reducing agent such as
dithiothreitol (DTT) is employed. DTT cleaves any disulphide bonds
between cysteine residues. The SDS-denatured and reduced polypeptides
are flexible rods with uniform negative charge per unit length. Thus,
• p13
protein electrophoresis • polyacrylamide gel electrophoresis
Table 2.1. Equipment choices for polyacrylamide gel electrophoresis
Choices for vertical systems

Hoefer miniVE
Gel size: 8 × 9 cm
Protein electrophoresis time: 1–2 h
One piece to cast and run gels
Accepts precast gels from most manufacturers
Blotting module can be used in same unit
Hoefer SE 250 and SE 260 (mini vertical)
Gel size: 8 × 7 cm, 8 × 9.5 cm

Temperature control: Alumina plate and built-in heat exchanger
Accepts precast gels from most manufacturers
Hoefer SE 600 (standard vertical)
Gel size: 14 × 16 cm
Temperature control: Built-in heat exchanger
Hoefer SE 400 (standard vertical)
Gel size: 14 × 16 cm
Choices for flatbed electrophoresis with precast gels

Multiphor II
Gel size: 25 × 11 or 18 × 0.5 cm

Protein electrophoresis time: 1.5 h
Temperature control: Ceramic heat exchanger
High resolution separations at high voltages
Wide range of precast gels available
Precast buffer strips eliminate need for large volumes of buffer
PhastSystem
Gel size: 43 × 50 × 0.45 mm

Electrophoresis and staining time: 1.5 h
Programmable power and temperature conditions for separation and staining
Precast gels available: denaturing, native and isoelectric focusing
t m 80-6013-88 • p14
Table 2.2. Electrophoresis system selection

Approx. gel size Number of
(w × l, cm) Number of gels Gel thickness (mm) samples/gel Heat exchanger
Vertical
Hoefer miniVE 8×7
8 × 9.5 1–2 0.75, 1, 1.5 5–18 N
Hoefer SE 250 8×7 1–2 0.75, 1, 1.5 5–18 Y
Hoefer SE 260 8×7

8 × 9.5 1–2 0.75, 1, 1.5 5–18 Y
Hoefer SE 600 14 × 15 1–4* 0.75, 1, 1.5 10–28 Y
Hoefer SE 400 14 × 15 1–2* 0.75, 1, 1.5 10–28 N
Flatbed
Multiphor II 25 × 11
25 × 18 1 0.5 25–48 Y
PhastSystem 4.3 × 5.0 1-2 0.45 6-12 Y
*Optional divider plate doubles capacity to four gels (SE 600) or two gels (SE 400).
because molecular weight is essentially a linear function of peptide chain

length, in sieving gels the proteins separate by molecular weight.
There are two types of buffer systems used in protein gel electrophoresis:
continuous and discontinuous. A continuous system uses only one buffer
for the tanks and the gel. In a discontinuous system, first developed by
Ornstein (1964) and Davis (1964), a nonrestrictive large-pore gel called a
stacking gel is layered on top of a separating (resolving) gel. The two gel
layers are each made with a different buffer, and the tank buffers differ
from the gel buffers.
In a discontinuous system, protein mobility—a quantitative measure of the

migration rate of a charged species in an electric field—is intermediate
between the mobility of the buffer ion of the same charge (usually negative)
in the stacking gel (leading ion) and the mobility of the buffer ion in the
upper tank (trailing ion). When electrophoresis is started, the ions and the
proteins begin migrating into the stacking gel. The proteins concentrate in a
very thin zone, called the stack, between the leading ion and the trailing ion.
The proteins continue to migrate in the stack until they reach the separating
gel. At that point, due to a pH or an ion change, the proteins become the
trailing ion and “unstack” as they separate on the gel.
Although a continuous system is slightly easier to set up than a discontinu-

ous system and tends to have fewer sample precipitation and aggregation
problems, much greater resolution can be obtained with a discontinuous
system. Only minimal concentration of the sample takes place with contin-
• p15
uous gels, and proteins form zones nearly as broad as the height of the
original samples in the sample wells, resulting in much lower resolution.
Denaturing gel electrophoresis can resolve complex protein mixtures

into hundreds of bands on a gel. The position of a protein along the
separation lane gives a good approximation of its size, and, after stain-
ing, the band intensity is a rough indicator of the amount present in
the sample. This simultaneous ability to estimate size and amount of a
protein is useful in various applications: estimating purity, level of gene
expression, immunoblotting, preparing for protein sequencing, and
generating antibodies.
The discontinuous Laemmli system (Laemmli, 1970), a denaturing modi-

fication of Ornstein (1964) and Davis (1964), is the most widely used
system for research protein electrophoresis today. The resolution in a
Laemmli gel is excellent because the treated peptides are concentrated in
a stacking zone before entering the separating gel. Other buffer systems
can be used, for example the Tris™-tricine system of Schägger and von
Jagow (1987) for resolution of polypeptides in the size range below
Mr 10 000. For a detailed discussion and general reference on denaturing
gel electrophoresis, consult the references listed at the end of this chapter.
The following protocol is for the use of the Laemmli SDS system in the
Hoefer SE 600 standard vertical apparatus.
Proper laboratory safety and chemical-handling procedures should be

observed in all electrophoresis work.
2.2.2 Stock solutions

Note: Use double-distilled water (ddH2O), deionized water, or other
high-quality water. Use the free base forms of Tris and glycine when
making these solutions. “Tris-Cl” is used in these formulations to indi-
cate that the pH of the solution is adjusted with concentrated HCl.
Caution: Acrylamide is a neurotoxin and Acrylamide solution Final concentration Amount

should be handled with care. (30% acrylamide, 0.8% bisacrylamide, 200 ml)
Acrylamide (FW 71.08) 30% 60 g
bisacrylamide (FW 154.17) 0.8% 1.6 g
ddH2O to 200 ml
Note: This will make a 30.8%T 2.7%Cbis solution.
Store up to 3 mo at 4 °C in the dark.
4× Resolving gel buffer

(1.5 M Tris-Cl, pH 8.8, 200 ml)
Tris (FW 121.1) 1.5 M 36.3 g
ddH2O 150 ml
HCl to pH 8.8
ddH2O to 200 ml
Store up to 3 mo at 4 °C.
t m 80-6013-88 • p16
4× Stacking gel buffer Final concentration Amount

(0.5 M Tris-Cl, pH 6.8, 50 ml)
Tris (FW 121.1) 0.5 M 3.0 g
ddH2O 40 ml
HCl to pH 6.8
ddH2O to 50 ml
Store up to 3 mo at 4 °C
10% SDS
SDS (FW 288.38) 10% 10 g
ddH2O to 100 ml
Store up to 6 mo at room temperature.
10% Ammonium persulphate (initiator)

Ammonium persulphate (FW 228.2) 10% 0.1 g
ddH2O to 1.0 ml
Prepare just prior to use; do not store.
Resolving gel overlay

(0.375 M Tris-Cl, 0.1% SDS, pH 8.8, 100 ml)
4× resolving gel buffer 1.5 M 25 ml
10% SDS 0.1% 1.0 ml
ddH2O to 100 ml
Store up to 3 mo at 4 °C.
2× Treatment buffer
(0.125 M Tris-Cl, 4% SDS, 20% v/v glycerol, 0.2 M DTT, 0.02% bromophenol
blue, pH 6.8, 10 ml)
4× stacking gel buffer 0.125 M 2.5 ml
10% SDS 4% 4.0 ml
Glycerol 20% 2.0 ml
Bromophenol blue 0.02% 2.0 mg
Dithiothreitol (DTT; FW 154.2) 0.2 M 0.31 g
ddH2O to 10.0 ml
Store in 0.5 ml aliquots at -20 °C for up to 6 mo.
Tank buffer
(0.025 M Tris, 0.192 M glycine, 0.1% SDS, pH 8.3, 10 l)
Tris (FW 121.1) 0.025 M 30.28 g
Glycine (FW 75.07) 0.192 M 144.13 g
SDS 0.1% 10 g
ddH2O to 10 l
This solution can be made up directly in large reagent bottles, because it is not necessary to check the pH.
Store at room temperature for up to 1 mo.
Water-saturated n-butanol
n-butanol 50 ml
ddH2O 5 ml
Combine in a bottle and shake. Allow phases to separate. Use the top phase to overlay gels.
Store at room temperature indefinitely.
• p17
Additional reagents
Protein standards (Table 2.3; Amersham Pharmacia Biotech LMW marker
kit #17-0446-01 for a molecular weight range of 14 400–94 000, and
HMW-SDS marker kit #17-0615-01 for a molecular weight range of
53 000–212 000).
Tetramethylethylenediamine (TEMED)
2.2.3 Materials and equipment

• SE 600 vertical slab gel unit with casting stand
• 1.5- or 0.75-mm-thick combs and spacers
• Glass plates
• 50 ml and 125 ml side-arm flasks
• Transfer pipettes
• Pipettor capable of pipetting 1–20 µl with long, narrow
“gel-loading” pipette tips
• Water aspirator or vacuum pump with trap
• Boiling-water bath or 100 ºC temperature block
• EPS 301 Power Supply (300 V)
• Magnetic stirrer
• Pipettes/graduated cylinders
Table 2.3. Protein standards with approximate molecular weights

Kit* Protein Molecular weight
LMW (17-0446-01) Phosphorylase b 94 000

Albumin 67 000
Ovalbumin 43 000
Carbonic anhydrase 30 000
Trypsin inhibitor 20 100
α-lactalbumin 14 400
HMW-SDS (17-0615-01) Myosin 212 000

α-2-Macroglobulin 170 000
β-Galactosidase 116 000
Transferrin 76 000
Glutamate dehydrogenase 53 000
HMW Native (17-0445-01) Thyroglobulin 669 000

Ferritin 440 000
Catalase 232 000
Lactate dehydrogenase 140 000
Albumin 67 000
Peptide Markers (80-1129-83) Horse myoglobin peptides 16 949

14 404
10 700
8 159
6 214
2 512
*From Amersham Pharmacia Biotech.
t m 80-6013-88 • p18
2.2.4 Procedure
Prepare the separating gel
1. Assemble the SE 600 vertical slab gel unit in the dual-gel casting stand.
Use 1.5 mm or 0.75 mm spacers (Fig 2.2a–d).
2. In a 125 ml side-arm vacuum flask, mix either 40 ml (0.75 mm) or

80 ml (1.5 mm) of resolving gel solution (Table 2.4), leaving out the
ammonium persulphate and the TEMED.
Fig 2.1. SE 600 Vertical Slab Gel Unit.
See Table 2.6 for recommended acrylamide concentrations.
3. Stopper the flask and apply a water vacuum for several minutes to
deaerate the solution while swirling the flask (Fig 2.3).
4. Add the TEMED and ammonium persulphate and gently swirl the
flask to mix, being careful not to generate bubbles.
5. Pipette the solution down the spacer into each sandwich to a level
about 4 cm from the top. A 25 ml pipette works well for this step.
6. Fill a transfer pipette or syringe with water-saturated n-butanol (or

Fig 2.2a Inserting the spacer. water or resolving gel overlay). Position the pipette or needle at about a
45° angle with the point at the top of the acrylamide next to a spacer.
Gently apply approximately 0.3 ml of n-butanol. Repeat on the other
side of the slab next to the other spacer. The n-butanol will layer evenly
across the entire surface after a minute or two. Repeat this process to
overlay the second slab.
A very sharp liquid-gel interface will be visible when the gel has polymer-
ized (Fig 2.4). This should be visible within 10–20 min. The gel should be
fully polymerized in about 1 h.
7. After polymerization, tilt the casting stand to pour off the overlay and
Fig 2.2b. Attaching the clamp.
rinse the surfaces of the gels twice with resolving gel overlay.
Gels may be stored at this point. The stacking gel is cast later. Remove
the n-butanol and add approximately 10 ml of 1× resolving gel overlay
solution to the top of each sandwich, seal with plastic wrap, and store
flat at 4 °C. Or store gels submerged flat in 1× resolving gel overlay at
4 °C for up to 1 wk.
8. Add approximately 1 ml of resolving gel overlay to each gel and allow

Fig 2.2c. Properly assembled gel sandwich.
Glass plates and spacer are flush. the gels to sit while preparing the stacking gel.
Prepare the stacking gel
9. In a 50 ml side-arm vacuum flask, mix 10 ml (for 0.75-mm-thick gels)

or 20 ml (for 1.5-mm-thick gels) of stacking gel solution (Table 2.4),
leaving out the ammonium persulphate and the TEMED.
10. Deaerate as in step 3.
11. Add the ammonium persulphate and TEMED. Gently swirl the flask
to mix.
Fig 2.2d. Assembling the gel casting stand (step 1).
The black cams are turned to seal the bottom surface
of the sandwich into the casting stand gasket.
• p19
Table 2.4. Resolving gel and stacking gel recipes for 1.5- and 0.75-mm-thick gels
Resolving gel solution (80 ml; 2 ea. 1.5-mm-thick SE 600/SE 400 gels)
Final gel concentration
5% 7.5% 10% 12.5% 15%

Acrylamide solution 13.3 ml 20 ml 26.7 ml 33.3 ml 40 ml
4× Resolving gel buffer 20 ml 20 ml 20 ml 20 ml 20 ml
10% SDS 0.8 ml 0.8 ml 0.8 ml 0.8 ml 0.8 ml
ddH2O 45.5 ml 38.8 ml 32.1 ml 25.5 ml 18.8 ml
10% Ammonium persulphate* 400 µl 400 µl 400 µl 400 µl 400 µl
TEMED* 27 µl 27 µl 27 µl 27 µl 27 µl
*Added after deaeration (step 3).
Resolving gel solution (40 ml; 2 ea. 0.75-mm-thick SE 600/SE 400 gels)
5% 7.5% 10% 12.5% 15%

10% SDS 0.4 ml 0.4 ml 0.4 ml 0.4 ml 0.4 ml
ddH2O 22.7 ml 19.4 ml 16.1 ml 12.8 ml 9.5 ml
10% Ammonium persulphate* 200 µl 200 µl 200 µl 200 µl 200 µl
TEMED* 13.3 µl 13.3 µl 13.3 µl 13.3 µl 13.3 µl

Stacking gel solutions (4% acrylamide; for two gels)
Gel thickness: 0.75 mm (10 ml total volume) 1.5 mm (20 ml total volume)
Acrylamide solution 1.33 ml 2.66 ml
4× Stacking gel buffer 2.5 ml 5 ml
10% SDS 0.1 ml 0.2 ml
ddH2O 6 ml 12 ml
10% Ammonium persulphate* 50 µl 100 µl
TEMED* 5 µl 10 µl
t m 80-6013-88 • p20
12. Pour off resolving gel overlay from the gel. Remove all liquid before
proceeding.
13. Fill each sandwich with stacking gel solution and insert a comb into
each sandwich, taking care not to trap any bubbles below the teeth of the
comb (Fig 2.5).
Oxygen will inhibit polymerization, and bubbles will cause a local distor-
tion in the gel surface at the bottom of the wells.
14. Allow the gel to sit for at least 30 min.
A very sharp interface will be visible when the gel has polymerized. This
Fig 2.3. Mixing the gel solution under vacuum (step should be visible within 10–20 min. The gel should be fully polymerized
3). A water aspirator is a convenient choice for this
procedure. after 1 h. In general, stacking gels should be cast just before use. The
complete gel can be stored overnight at 4 °C, however, with little effect
on resolution, if covered and the comb left in place.
Prepare the sample
15. Combine equal volumes of protein sample and 2× treatment buffer in

a tube and place the tube in a boiling-water bath for 90 s. If using dry
samples, add equal volumes of water and 2× treatment buffer and heat in
a boiling-water bath for 90 s.
See ‘Troubleshooting’ section for more on sample preparation and how

Fig 2.4. Polymerized resolving gel with to ensure sharp bands. If the gels will be stained with Coomassie Blue, use
n-butanol overlay.
a starting sample protein concentration of 10–20 mg/ml (i.e. 10–20 µg/µl).
This will be diluted by the 2× treatment buffer to give 5–10 µg/µl. For
complex mixtures (e.g. cell lysates), 50 µg of protein (5–10 µl of treated
sample) per lane is recommended. For highly purified proteins, 0.5–5 µg
per lane is usually adequate. Silver staining requires 10- to 100-fold less
protein per lane.
16. Place samples briefly on ice until ready for use. The treated sample
can be stored at 20 °C for 6 mo for future runs.
Note: The SDS may precipitate if tubes are left on ice for long periods of time.
Fig 2.5. Inserting comb into stacking gel
(step 13). Insert the comb at an angle to avoid Load the gels
trapping bubbles under the comb teeth.
17. Slowly remove the combs from the gels, raising the comb up to avoid
disturbing the well dividers (Fig 2.6).
18. Rinse each well with tank buffer, invert the casting stand to drain the
wells, and return the stand to an upright position.
19. Fill each well with tank buffer.
20. Using a pipettor with a long, thin tip (or a Hamilton™ syringe), gently
load 5–10 µl of sample beneath the buffer in each well (Fig 2.7a). Load
every well with the same volume of sample. If the well is not needed,
load with 1× sample buffer containing standard protein or no sample.
Fig 2.6. Removing comb from stacking gel
(step 17). Do this gently to avoid damaging the
well arms.
• p21
This procedure ensures that each well behaves the same during separa-
tion. If an adjacent well is left empty, the adjoining samples will tend
to spread laterally during electrophoresis.
When adding the sample, be careful to maintain a sharp interface

between the sample and the tank buffer (Fig 2.7a). Adding the sample
too fast or erratically will lead to swirling and a diffuse loading zone.
This will cause a loss of band sharpness (Fig 2.7b). Alternatively, the
sample can be added and then overlaid with tank buffer. This is more
time-consuming but, when performed carefully, minimizes contamination
between wells and is particularly useful with radiolabelled samples.
Fig 2.7a. Loading the sample (step 20). Use a very
steady hand to load sample and maintain a sharp 21. If protein molecular weight standards are used, load one or two
interface between the sample and the tank buffer.
wells with 5–10 µl of the standard mixture. If the gel is to be stained
with Coomassie Blue, this volume should contain 0.2–1 µg of each
standard component. If the gel is to be silver stained, use 10–50 ng of
each component.
Run the gel
22. Fill the lower buffer chamber with 4 l of tank buffer. Install the sealing
gaskets on the upper buffer chamber and put it in place on the gel sand-
wiches. Remove the lower cams and cam the sandwiches to the bottom of
the upper buffer chamber. Put the upper buffer chamber in place on the
Fig 2.7b. The wrong way to load the sample. heat exchanger in the lower buffer chamber (Fig 2.8).
The well on the left was loaded too quickly and
with too much volume, creating a large diffuse 23. Adjust the height of the tank buffer in the lower buffer chamber until
sample zone, while the well bottom on the right
was damaged with the needle. Note that the right the sandwiches are fully immersed in buffer. If bubbles are trapped under
well arm is not straight; with large volumes this the ends of the sandwiches, coax them away with a pipette.
will decrease resolution.
24. Add a spin bar to the lower buffer chamber and center the chamber
on a magnetic stirrer.
When the lower buffer is stirred, the temperature of the buffer remains
uniform. This is important because uneven heating distorts the band
pattern of the gel and leads to smiling.
25. Carefully fill the upper buffer chamber with tank buffer. Do not pour
buffer into the sample wells, because it will wash the sample out.
Fig 2.8. Locking the upper buffer chamber in place. 26. Put the lid on the gel unit and connect it to the EPS 301 Power
Supply. The cathode (black lead) is connected to the upper buffer cham-
ber (Fig 2.9).
27. Turn on the power supply and adjust the voltage to 300 (so voltage
is not limiting).
28. Adjust the current to 30 mA per 1.5-mm-thick gel and 15 mA per

0.75-mm-thick gel. Start the electrophoresis. The voltage should start at
about 70–80 V, but will increase during the run. Keep a record of the
voltage and current readings so that future runs can be compared and
current leaks or incorrectly made buffers can be detected.
Under these conditions, the gel will take approximately 3–4 h to run. If it
Fig 2.9. The SE 600 fully assembled. is more convenient to run the gel for a longer period (e.g. 8 h), reduce the
t m 80-6013-88 • p22
current to half—15 mA per 1.5-mm-thick gel; reduce the current to

7 mA per 1.5-mm-thick gel for 16 h (e.g. overnight).
29. When the tracking dye reaches the bottom of the gel, turn the power
supply off and disconnect the power cables.
Disassemble the gel sandwiches
30. Remove the buffer and disassemble the sandwiches by gently loosen-
ing and sliding away both spacers. Slip an extra spacer or a Hoefer
Wonder Wedge into the bottom edge and separate the plates. Carefully
lift the gel into a tray of staining solution or fixative as outlined in the
‘Staining’ section of Chapter 4.
Fig 2.10. Coomassie Blue stained gel. An example of a Coomassie Blue stained gel is shown in Figure 2.10.
2.3 Separating proteins on denaturing mini-gels

2.3.1 Introduction
Separating proteins with small gels is similar to running large gels except
that volumes and separation times are considerably less. Like the large
format, gels are cast either one or two at a time in the dual-gel caster, or
in groups of four to 10 in a multiple caster. The combination of fast sepa-
rations and small size makes mini-gels a very popular alternative to stan-
dard-size gels. Although the separation gel area is much less, generally
resolution is adequate for most routine procedures. Large-format gels are
still recommended when high resolution is paramount.
The Hoefer miniVE offers the convenience of both electrophoresis and

electrotransfer in one compact instrument with only four major parts.
The gel module is simultaneously a casting stand and an upper buffer
chamber. An optional blot module is available, which folds into the
miniVE tank. The SE 250 and SE 260 uses alumina plates to effectively
remove heat from gel to buffer. There is also a cooling option.
The following protocols cast one or two gels at a time in the dual-gel
caster. The Mighty Small dual-gel caster holds glass or glass/alumina plate
gel sandwiches for simple casting of gels. The bottom of the sandwich is
sealed against a rubber gasket by a cam action. Once the gel is set, the
sandwiches are transferred to a Hoefer SE 250, SE 260, or miniVE mini-
gel electrophoresis unit. Refer to Section 2.1, ‘Equipment choices,’ for
guidelines on selecting an appropriate mini-gel unit.
The following procedure has been written for use with the Hoefer SE 250/
SE 260 mini-gel units. The Hoefer miniVE can also be used for running
mini-gels. Its modular design incorporates a blotting system and is an
appropriate choice when blotting follows electrophoresis. The procedure
outlined below may also be followed when using the miniVE (the plates
and volumes of solutions are the same); however, certain steps will not
apply, such as the description of installing the plates on the unit. Side
notes have been included when there are significant differences. Refer to
instrument instructions for details.
• p23

• Stock solutions from section 2.2.2
• 50 ml and 125 ml side-arm flasks
• Hoefer SE 250, SE 260, or miniVE mini-gel electrophoresis
unit with plates, combs, and spacers
• SE 245 dual-gel casting stand
• Pipettes and pipettors
Fig 2.11. Slide the sandwich into the clamp
• EPS 301 Power Supply
assembly with the notched plate facing inward
and secure by tightening screws. • Precast gels can also be used and are available from several
manufacturers
2.3.3 Procedure
Prepare the resolving gel
1. For each sandwich, choose one notched alumina (SE 250 or SE 260)
or one notched glass plate (miniVE), one rectangular glass plate, and two
spacers. Do not use chipped plates. Lay the notched plate on a flat surface
Fig 2.12. Place the clamp assembly in the casting and place one spacer along each edge extending along the side of the notch
cradle, screw side facing outward. In this position
the gel will be visible through the rectangular glass (on the “ear”). Fit a glass plate onto the spacers. The top of the T of the
plate. Insert a cam and seal the gel sandwich by spacer rests along the side of the gel sandwich. On a flat surface, align the
turning both cams 180°.
sides with the spacers and also the bottom.
2. Hold the sandwich by the flat sides firmly between your thumb and
B. clamp fingers. With the notched plate facing the clear back block, slide the
sandwich into the clamp assembly, making sure the bottom edge of the
sandwich rests on the flat surface. Insert a Hoefer Spacer-Mate™ to
realign spacers that may have moved.
A. load 3. While holding the sandwich in place, secure it by tightening all six pres-
sure bar screws finger-tight. (To prevent glass breakage, do not overtighten.)
4. Inspect the sandwich bottom to make sure that both plates and the
spacers are aligned and even and that the bottom edge would rest on a
C. seal flat surface. (The sandwich should protrude slightly below the back
and cast
block; this position helps ensure a complete seal.) Adjust if necessary.
5. Place the clamp assembly in the casting cradle, screw side facing out.
For the miniVE unit, assemble the sandwich so the glass In this position the gel will be visible through the rectangular glass plate.
and spacers are aligned. Place the sandwich flat on
the electrophoresis module with the notched plate to 6. Insert a cam into the hole on each side of the casting tray so that the
the back and the notch at the top. (A) Check to make arrow (short end) points up. Seal the gel sandwich by turning both cams
sure that the glass plates and spacers are flush with
the guide feet at the bottom of the module. While
180° so that the arrow points down. (Fig 2.12)
holding the sandwich in place, slide each clamp into
position and gently tighten the screws. (B) Check the Pour the gel
bottom-edge alignment of the sandwich and adjust
the glass and spacers to ensure that the bottom edges
7. Prepare the resolving gel solution in a 125 ml vacuum flask as described
are completely flush. Finish tightening the screws
finger-tight. Raise the sealing plate into place until in Table 2.5 except omit the TEMED and ammonium persulphate.
the tabs are engaged in the topmost notch. (C) Stand
the caster upright or hang it from the miniVE cham- Also, see Table 2.6 for recommended acrylamide concentrations.
ber. Prepare gel solutions and cast the gel as per the
SE 250/SE 260 instructions.
t m 80-6013-88 • p24
Table 2.5. Resolving gel recipes for 1.5- and 0.75-mm-thick gels
(20 ml; 2 ea. 1.5-mm-thick, 8 × 7 cm SE 250 gels)
5% 7.5% 10% 12.5% 15%

10% SDS 0.2 ml 0.2 ml 0.2 ml 0.2 ml 0.2 ml
ddH2O 11.4 ml 9.7 ml 8 ml 6.4 ml 4.7 ml
Ammonium persulphate* 100 µl 100 µl 100 µl 100 µl 100 µl

(10 ml; 2 ea. 0.75-mm-thick, 8 × 7 cm SE 250 gels)

5% 7.5% 10% 12.5% 15%

Acrylamide solution 1.67 ml 2.5 ml 3.3 ml 4.2 ml 5 ml
4× Resolving gel buffer 2.5 ml 2.5 ml 2.5 ml 2.5 ml 2.5 ml
10% SDS 0.1 ml 0.1 ml 0.1 ml 0.1 ml 0.1 ml
ddH2O 5.7 ml 4.9 ml 4 ml 3.2 ml 2.4 ml

(30 ml; 2 ea. 1.5-mm-thick, 8 × 10 cm SE 260/SE 280 or miniVE gels)

5% 7.5% 10% 12.5% 15%

Acrylamide solution 5 ml 7.5 ml 10 ml 12.5 ml 15 ml
10% SDS 0.3 ml 0.3 ml 0.3 ml 0.3 ml 0.3 ml
ddH2O 17.1 ml 14.6 ml 12 ml 9.6 ml 7.1 ml
(15 ml; 2 ea. 0.75-mm-thick, 8 × 10 cm SE 260/SE 280 or miniVE gels)

5% 7.5% 10% 12.5% 15%

Acrylamide solution 2.5 ml 3.8 ml 5 ml 6.3 ml 7.5 ml
10% SDS 0.15 ml 0.15 ml 0.15 ml 0.15 ml 0.15 ml
ddH2O 8.6 ml 7.4 ml 6 ml 4.8 ml 3.6 ml
• p25
Table 2.6. Recommended acrylamide concentrations for protein separation
(See Table 2.3 for appropriate standards.)

Separation size range (kD) % acrylamide in resolving gel
36–205 5%
24–205 7.5%
14–205 10%
14–66* 12.5%
14–45* 15%
*The larger proteins fail to move significantly into the gel.
8. Stopper the flask and apply a vacuum for several minutes while
swirling the flask.
10. Use a pipette to deliver the solution into one corner of the plate,
taking care not to introduce any air pockets. Fill solution to 3 cm below
the top of the rectangular glass plate. This height allows 1 cm of stacking
gel below the wells.
11. Using a pipettor or syringe, add 100 µl of water-saturated n-butanol

(or water or diluted resolving gel buffer) near the spacer at the side of the
gel sandwich to overlay the gel and prevent its exposure to oxygen.
Allow gel to polymerize 1 h.
12. Pour off the overlay and rinse the gel sandwich with diluted resolving
buffer. Rinse the gels twice with resolving gel overlay.
Gels may be stored at this point. The stacking gel (step 13) is cast later.
Remove the n-butanol and add approximately 5.0 ml of 1× resolving gel
overlay to the top of each sandwich, seal with plastic wrap, and store flat
at 4 °C. Or store gels submerged flat in 1× resolving gel overlay at 4 °C
for up to 1 wk.
Table 2.7. Stacking gel solutions (for two gels)

Gel thickness: 0.75 mm 1.5 mm
Acrylamide solution 0.44 ml 0.88 ml
4× Stacking gel buffer 0.83 ml 1.66 ml
10% SDS 33 µl 66 µl
ddH2O 2.03 ml 4.06 ml
Ammonium persulphate* 16.7 µl 33.4 µl
TEMED* 1.7 µl 3.3 µl

*Added after deaeration.
t m 80-6013-88 • p26
13. In a 50 ml side-arm flask, prepare stacking gel solution as described

in Table 2.7 except omit the TEMED and ammonium persulphate.
Pour the stacking gel either while the sandwich is still in the gel caster or
after it is transferred to the electrophoresis unit (see instructions with
unit). The stacking gel should be cast just before use.
14. Stopper the flask and apply a vacuum for several minutes to deaerate
the solution while swirling the flask.
Fig 2.13. Add stacking gel and insert comb at an
angle to avoid trapping bubbles. 16. Use a Pasteur pipette to apply the stacking gel over the resolving gel.
17. Introduce a comb (at a slight angle) into the sandwich, taking care
not to trap air under the teeth (Fig 2.13). Allow gel to polymerize 1 h.
18. Remove the comb from the sandwich by carefully pulling on the comb
while gently rocking it back and forth to break the suction (Fig 2.14).
Rinse the wells with tank buffer.
19. Loosen the casting cradle pressure bar screws, tilt the gel sandwich
Fig 2.14. Remove comb and wash wells to remove forward, and lift it out.
unreacted acrylamide.
The cutout in the top of the back plate facilitates easy removal of the
sandwich.
Install the gel
20. To install the gel, use the following guidelines (Fig 2.15a-c).
I. SE 250
To install lab-cast or precast 10 × 8 cm plates, orient the sandwich so

that the notched plate faces the gasket with the notch at the top. Set the
Fig 2.15a. bottom of the sandwich on the bottom of the lower buffer chamber and
center the plate so that the gasket seals both sides (Fig 2.15a).
II. SE 260
To install a lab-cast or precast 10 × 10.5 cm gel sandwich, orient the

sandwich so that the notched plate faces the gasket and the notch is at
the top. Set the bottom of the sandwich on the supporting ledges on the
bottom of the lower buffer chamber and center the plate so that the
gasket seals both sides (Fig 2.15b).
Fig 2.15b.
If installing a self-cast or precast 10 × 8 cm gel sandwich, align the top of
the plate with the top of the core. The bottom of the notched plate must
cover the silicone rubber gasket (Fig 2.15c).
III. Precast gels (10 × 10 cm) using the SE 260
Precast gels for the SE 250, SE 260, and miniVE must have a notch in
the back plate to seal along the sides of the sandwich and to make buffer
contact at the top of the sandwich.
Fig 2.15c.
• p27
Orient the sandwich so that the notched plate faces the gasket with the
notches at the top. Set the bottom of the sandwich on the supporting
Precast gels on the miniVE ledges on the bottom of the lower buffer chamber and center the plates
so that the gasket seals along both sides. Correct alignment is important
Position the cassette on the module so that the
notched side is on the gasket and the wells are at to create a proper seal. Lightly press the sandwich against the gasket.
the top of the module. Slide the clamps in place
over the gel and tighten the screws. 21. Lightly press the sandwich against the gasket and secure it to the
Gels cast on the miniVE need not be transferred, core with one spring clamp on each side. Position the clamp so that the
because both casting and electrophoresis are shorter rounded jaw edge fits into, but not past, the core groove and the
performed using the same module. After the gel
has been prepared, move the sealing plate to the longer jaws fits on the glass plate. Slide the clamps so that they are
half-open position (the lower notch). centered along the groove (Fig 2.16).
Lower the module into the gel tank and fill both
the upper and lower buffer chambers to the recom- 22. Repeat step 20 for the second sandwich or, if running only one gel,
mended levels with SDS electrophoresis buffer. clamp a blank cassette or a plain glass plate on the unused side of the
core to prevent a possible short circuit with the unused electrode. Do not
fill this chamber with buffer if no gel sandwich is in place.
Prepare and load sample
23. Wet the well-locating decal (Fig 2.17) and let it adhere to the front
of the glass plate so that the appropriate edge outlines the sample wells.
The decal will help with sample loading.
For precast gels or gels in miniVE, make a mark with a marking pen on
the glass plate at the bottom of each well. This will make the wells more
Fig 2.16. Place gel on the SE 250 upper buffer
chamber. visible for loading when filled with buffer.
24. Fill the sample wells and each upper buffer chamber containing a gel
sandwich with tank buffer.
One upper buffer chamber holds approximately 75 ml.
25. Underlay the sample into the wells using a fine-tipped microsyringe or
pipettor with long, thin pipette tips (Fig 2.17).
Typical sample volumes range from 5 to 10 µl, although this depends on

the gel thickness. Use step 15 in the previous Laemmli SDS-PAGE section
(2.2.4) as a guide to sample preparation.
Fig 2.17. Use the supplied template as a guide to
load samples. Assemble the apparatus
26. Fill the lower buffer chamber with tank buffer. Ensure that the lower
electrode, which runs along the bottom of the upper buffer chamber core,
is completely submerged.
The SE 250 lower buffer chamber holds about 150 ml, and the SE 260
holds about 250 ml. The miniVE requires a minimum of 1 l for the lower
buffer chamber.
27. Place the safety lid on the unit and plug the colour-coded leads into
the jacks in the power supply (red to red, black to black).
t m 80-6013-88 • p28
28. Optional for the SE 250 and SE 260: Using a thermostatic circulator,
begin circulating cold water or a chilled 50:50 mixture of water and
ethylene glycol.
Run and process the gel
29. Run the gels under appropriate conditions. For example, run two 7 cm
× 0.75 mm Laemmli gels approximately 1 h at 30 mA (15 mA per gel,
constant current). Check band progress after 5 min and again after 30 min
to monitor the position of the tracking dye.
Gels may be run at either constant current or constant voltage. A constant-

current setting is traditionally used with a discontinuous buffer system
so that the rate of electrophoretic migration remains unchanged through-
out the run. Under these conditions voltage increases as the run proceeds.
A lower current setting is recommended for higher resolution.
Run precast gels under the same current and voltage conditions as
self-cast gels.
The run is complete when the tracking dye reaches the bottom of the gel.
For the miniVE unit remove the gel module and 30. When the tracking dye reaches the bottom of the gel, turn off the
dispose of the buffer. Unscrew the clamps and
remove the gel sandwich.
power supply, disconnect the leads, and remove the safety lid.
31. If coolant is circulating, stop the flow and disconnect the fittings or
tubing.
32. Invert the core assembly and pour out the buffer, remove both clamps,
and lift away gel sandwich(es) from the upper buffer chamber core.
33. Gently loosen and slide away both spacers. Slip an extra spacer or a
Hoefer Wonder Wedge into the bottom edge (to prevent breaking the ears
of the notched plates) and separate the plates. The gel may adhere to the
alumina plate. Carefully lift the gel from the plate and lay it into a tray of
stain or fixative as outlined in the ‘Staining’ section of Chapter 4.
A typical gradient gel is shown in Figure 2.18.
Fig 2.18. Mini-gels are capable of very high resolu-

tion separation. 1.5-mm-thick 5–20% gradient SDS-
PAGE gel. High and low molecular weight standards
stained with Coomassie Blue are shown. Separation
conditions were 20 mA for 120 min.
• p29
2.4 Preparing linear pore-gradient gels

2.4.1 Introduction
Gradient gels, although more difficult to cast than single-concentration
gels, resolve a much wider size range of proteins on a single gel. Further-
more, calculating molecular weights is simplified because, unlike single-
concentration gels, the relationship between log size and mobility is linear
over most of the fractionation range of the gel (see Fig 4.10, Chapter 4).
The protocol below describes casting one gradient gel at a time. Multiple
gradient gels can be cast using a multiple-gel caster. Consult the manufac-
turer’s instructions for casting several gradient gels at once.

• Gel solutions from section 2.2.2
• Sucrose
• Gradient maker (SG 50 for SE 600 and SG 15 for the SE 250
size mini-gels)
• Peristaltic pump capable of 1.6 ml/min
• Pump tubing with attached pipette tip
• Ring stand
• 125 ml side-arm flask
• Magnetic stirrer
• Small stir bar
• Electrophoresis unit (Hoefer SE 600 for standard-size gels or SE 250
for mini-gels) with spacers, combs, and glass plates
• Casting stand (SE 245 for mini-gels or SE 600 casting stand)
• EPS 301 Power Supply
gradient maker 2.4.3 Procedure

reservoir mixing chamber
(heavy solution)
1. Set up the SE 245 or SE 600 gel casting stand with two glass sandwiches.
chamber
(light solution)
mixing valve
outlet valve
2. Connect a piece of tubing to the outlet tubing connector of the side-
outlet port
stir bar
outlet gradient maker. Attach a micropipette tip to the other end of the
tubing and, using a ring stand and clamp, position the tip at the top
center of the sandwich (Fig 2.19). Use the clamp to hold the pipette tip
firmly in place. The dispensing end of the pipette tip should be 0.5–1 mm
inside the gel sandwich. Attach the tubing to the peristaltic pump.
stir
plate
The pump rate should be set so that casting takes 5–10 min.
3. In separate flasks mix all ingredients listed in Table 2.8 for the light
dual gel caster and heavy running gradient gel solutions, including the ammonium
persulphate. Do not add TEMED.
peristaltic pump
A 5–20% or 10–20% gradient gel is recommended.
Fig 2.19. Setup for casting gradient gels
one at a time. When casting from the top in a
Deaeration is not needed in this protocol. Once mixed, keep the heavy
single-gel caster, the heavy solution enters first. solution on ice to prevent polymerization. High-concentration acrylamide
solutions may polymerize without the addition of TEMED once the
ammonium persulphate has been added.
t m 80-6013-88 • p30
Table 2.8. Gradient gel solutions, part 1
Light solution
(5 ml one 1.5- or two 0.75-mm-thick SE 250 gels) Final gel concentration
5% 7.5% 10% 12.5% 15%
Acrylamide solution 0.84 ml 1.25 ml 1.65 ml 2.1 ml 2.5 ml
10% SDS 0.05 ml 0.05 ml 0.05 ml 0.05 ml 0.05 ml
ddH2O 2.85 ml 2.45 ml 2 ml 1.6 ml 1.2 ml
10% Ammonium persulphate 45 µl 40 µl 32 µl 27 µl 20 µl

*Added just before pouring gel.
Heavy solution
10% 12.5% 15% 17.5% 20%
Acrylamide solution 1.65 ml 2.1 ml 2.5 ml 2.92 ml 3.3 ml
10% SDS 0.05 ml 0.05 ml 0.05 ml 0.05 ml 0.05 ml
Sucrose 0.75 gm 0.75 gm 0.75 gm 0.75 gm 0.75 gm
ddH2O 1.62 ml 1.17 ml 0.77 ml 0.35 ml 0 ml

• p31
Light solution
(10 ml one 0.75-mm-thick SE 600 gel or two 1.5-mm-thick SE 250 gels)
5% 7.5% 10% 12.5% 15%
Acrylamide solution 1.67 ml 2.5 ml 3.3 ml 4.2 ml 5 ml
10% SDS 0.1 ml 0.1 ml 0.1 ml 0.1 ml 0.1 ml
ddH2O 5.7 ml 4.9 ml 4 ml 3.2 ml 2.4 ml

Heavy solution
10% 12.5% 15% 17.5% 20%
4× Resolving Gel buffer 2.5 ml 2.5 ml 2.5 ml 2.5 ml 2.5 ml
10% SDS 0.1 ml 0.1 ml 0.1 ml 0.1ml 0.1 ml
Sucrose 1.5 gm 1.5 gm 1.5 gm 1.5 gm 1.5 gm
ddH2O 3.23 ml 2.33 ml 1.53 ml 0.70 ml 0 ml

t m 80-6013-88 • p32
Light solution
(20 ml one 1.5- or two 0.75-mm-thick SE 600 gels)
5% 7.5% 10% 12.5% 15%
10% SDS 0.2 ml 0.2 ml 0.2 ml 0.2 ml 0.2 ml
ddH2O 11.4 ml 9.8 ml 8 ml 6.4 ml 4.8 ml

Heavy solution
10% 12.5% 15% 17.5% 20%
10% SDS 0.2 ml 0.2 ml 0.2 ml 0.2 ml 0.2 ml
Sucrose 3 gm 3 gm 3 gm 3 gm 3 gm
ddH2O 6.46 ml 4.66 ml 3.06 ml 1.40 ml 0 ml

• p33
Light solution
(40 ml two 1.5-mm-thick SE 600 gels) Final gel concentration

5% 7.5% 10% 12.5% 15%
10% SDS 0.4 ml 0.4 ml 0.4 ml 0.4 ml 0.4 ml
ddH2O 22.8 ml 19.6 ml 16.1 ml 12.8 ml 9.6 ml

Heavy solution
10% 12.5% 15% 17.5% 20%
Acrylamide Solution 13.2 ml 16.8 ml 20 ml 23.32 ml 26.6 ml
4× Resolving Gel Buffer 10 ml 10 ml 10 ml 10 ml 10 ml
10% SDS 0.4 ml 0.4 ml 0.4 ml 0.4 ml 0.4 ml
Sucrose 6 gm 6 gm 6 gm 6 gm 6 gm
ddH2O 12.92 ml 9.32 ml 6.12 ml 2.8 ml 0 ml
10% Ammonium Persulphate 200 µl 180 µl 80 µl 80 µl 80 µl

t m 80-6013-88 • p34
4. Add the TEMED and gently swirl the flasks to mix.
Note: Alternatively, add gel solution to the gradient maker before adding
Table 2.9. Recommended volume per TEMED. Just before opening the outlets, add 0.33 µl of TEMED per
chamber for casting a single gradient gel
milliliter of gel solution and mix by drawing in and out of a disposable
Thickness plastic pipette. If this technique is used, a large volume of heavy and light
0.75 mm 1.5 mm solutions can be prepared in advance and dispensed into the gradient
SE 250 1.7 ml 3.5 ml maker for each individual gel. This is useful when casting several gels
SE 600 7 ml 14 ml individually without using a multiple-gel caster.
5. Pour the heavy solution into the chamber closest to the outlet (mixing
chamber) of the gradient maker (Fig 2.19). See Table 2.9 for recom-
gradient maker mended volumes per chamber. Add a small magnetic stir bar. See also
reservoir mixing chamber note in step 4 above.
chamber (light solution)
(heavy solution)
outlet valve The heavy solution enters the gel sandwich first when casting gels one at
mixing valve
outlet port a time from the top.
stir bar
multiple
gel caster When casting gels in a multiple-gel caster, the gels fill through the inlet at
the bottom, and the light solution must enter first. Thus, with multiple-
gel casters, the light solution is placed in the mixing chamber (Fig 2.20).
stir
plate 6. Open the valve between the two chambers and allow a small amount
of the heavy solution to flow through the channel to, but not into, the
inlet port
bottom of the reservoir chamber. Close the valve.
7. Pour the light solution into the reservoir chamber. See also note in
step 4 above.
peristaltic pump
8. Place the gradient maker on a magnetic stirrer and begin stirring.

Fig 2.20. Setup for casting gradient gels using a
multiple-gel caster. When using a multiple-gel
9. Turn on the pump and open the outlet valve.
caster, the light solution enters first.
10. Once the tubing has filled with a few centimeters of heavy gel solution,
open the valve between the two chambers. Continue to pump until all the
liquid is in the sandwich.
11. Overlay the gel with 0.3 ml of water-saturated n-butanol and allow
the gel to polymerize. Continue procedure with casting the stacking gel in
step 9 in section 2.2.4 for standard-size gels or step 12 of section 2.3.3
for mini-gels. Typical gradient gels are shown in Figures 2.18 and 2.21.
Fig 2.21. 5–20% acrylamide gradient gel. 0.75-

mm-thick SDS gel was separated overnight at 4 mA
and stained with Coomassie Blue. Outside lanes
contain protein standards.
• p35
2.5 Native gel electrophoresis

Under native PAGE conditions, polypeptides retain their higher-order
structure and often retain enzymatic activity and interaction with other
polypeptides. The migration of proteins depends on many factors,
including size, shape, and native charge. The resolution of nondenaturing
electrophoresis is generally not as high as that of SDS-PAGE, but the
technique is useful when the native structure or enzymatic activity of a
protein must be assayed following electrophoresis. One straightforward
approach to native electrophoresis is to omit the SDS and reducing agent
(DTT) from the standard Laemmli SDS protocol. Prepare the gels as
described above, but do not put SDS or DTT in the sample buffer, do not
heat the samples, and prepare the gel and tank buffer solutions without
SDS. For more information on native PAGE under different conditions,
consult Hames, 1998.
2.6 Separating proteins by flatbed SDS-PAGE

2.6.1 Introduction
Flatbed systems using ultrathin gels polymerized on support films offer
advantages over vertical systems: simpler handling; convenience of ready-
made gels and buffer strips (which eliminates the need for preparing large
buffer volumes); good cooling efficiency; possibility of washing, drying,
and rehydrating the gels; and the possibility of automation.
Amersham Pharmacia Biotech offers the Multiphor II system and Phast-

System for running gels in a flatbed format (see Table 2.1 and 2.2 in
Section 2.1). The Multiphor II system provides excellent resolution and
relatively rapid separations in a large-format gel. It allows cooling of
ultrathin gels efficiently and uniformly, through a ceramic heat exchanger,
for improved resolution and speed at high voltages. The PhastSystem
automates both the running and staining of precast mini-gels.
The availability of a wide range of ultrathin gels makes running flatbed

gels very convenient. Table 2.10 lists the precast gels available for the
Multiphor II system.
Fig 2.22. Multiphor II Flatbed

The following procedure outlines the use of the Multiphor II unit (Fig 2.22)
Electrophoresis System. for separating proteins on a precast SDS 7.5% acrylamide gel.

• Kerosene or light paraffin oil
• ExcelGel™ SDS Homogeneous 7.5% (precast SDS-polyacrylamide
gel on plastic backing)
• ExcelGel SDS buffer strips
• Multiphor II Electrophoresis unit
• MultiTemp™ III Thermostatic Circulator
• EPS 3501 or EPS 1001 Power Supply
• Multiphor Buffer Strip Positioner (optional)
t m 80-6013-88 • p36
Table 2.7. Precast acrylamide gels and buffer kits for Multiphor II System
Product Application* Sample no./gel Volume (µl) Buffer
ExcelGel SDS Gradient, 8–18% strip 26 1–40 A
ExcelGel SDS Homogeneous

7.5% well 25 5–17 A
12.5% well 25 5–17 A
15% well 25 5–17 A
ExcelGel SDS buffer strips B, C

(anode and cathode)
CleanGel™ SDS and Native PAGE

25S well 25 5–17
36S well 36 5–7
48S well 48 8
CleanGel Buffer Kits

SDS, pH 8.0
Native, pH 5.5
Native, pH 8.9
Ampholine PAGplate IEF

pH 3.5–9.5 strip 26–52 1–40
pH 4.0–6.5 strip 26–52 1–40
pH 5.5–8.5 strip 26–52 1–40
pH 4.0–5.0 strip 26–52 1–40
CleanGel Dry IEF strip 26–52 1–40
Immobiline DryPlate IEF

pH 4.0–7.0 strip 26–52 1–40
pH 4.2–4.9 strip 26–52 1–40
pH 4.5–5.4 strip 26–52 1–40
pH 5.0–6.0 strip 26–52 1–40
pH 5.6–6.6 strip 26–52 1–40
*Application refers to the method of applying the sample on the gel. The ExcelGel Homogeneous gels and CleanGel SDS and Native gels are made with preformed wells for applying
samples. Others (labelled strip) require an application strip or sample application pieces for applying samples.
A: Tris/HAc pH 6.4
B: Tris/HAc pH 5.6
C: Tris/tricine pH 7.1
• p37
2.6.3 Procedure
Instrument and gel preparation
1. Connect the Multiphor II electrophoresis unit to the MultiTemp III
thermostatic circulator and set the temperature to 15 °C. Turn on the
thermostatic circulator 10 min before starting the analysis.
2. Pipette 1–2 ml of kerosene or light paraffin oil onto the cooling plate
of the electrophoresis unit.
3. Remove the precast gel from the foil package by cutting away the edges
of the foil. Markings on the plastic cover of the gel indicate the direction
of electrophoresis.
Note: Gels without preformed wells also have a notch at the lower-left
corner of the film that identifies the anodic (+) end.
4. Orient the gel according to these markings and remove the gel cover.
Fig 2.23. Placing the gel on the Multiphor II
Carefully lower the gel onto the cooling plate, allowing the kerosene or oil
cooling plate.
to spread evenly underneath the gel. Make sure no bubbles are trapped
beneath the gel (Fig 2.23).
Apply the buffer strips

5. Place the two colour-coded buffer strips on the gel. Peel back the foil
on the colourless cathodic (–) ExcelGel SDS buffer strip. Place the buffer
strip with the smooth, narrow face downward along and in complete
contact with the cathodic edge of the SDS gel. Avoid trapping air bubbles
between the gel and the buffer strip.
Note: The Multiphor II Buffer Strip Positioner (80-6442-90) simplifies

buffer strip placement and promotes straighter runs by ensuring precise
Fig 2.24a. Multiphor II Buffer Strip Positioner.
positioning. Please see the instructions (80-6443-66) for guidelines on the
use of this product (Fig 2.24a).
If the buffer strip breaks, piece it together on the gel.
6. Repeat step 5 with the orange anodic (+) ExcelGel buffer strip, placing
it along the anodic edge of the SDS gel (Fig 2.24b).
Apply the sample and run the gel

7. Pipette the samples and/or standards into the wells of the gel.
Use 5–20 µl sample volumes.
8. Place the electrode holder and align the electrodes over the center of
the buffer strips. Lower the electrode holder so that the electrodes rest on
Fig 2.24b. Place the appropriate colour-coded buffer
strips along the anodic and cathodic ends top of the buffer strips. Connect the two electrodes to the base unit and
of the gel. place the lid on the unit.
9. Connect the leads to the power supply. Set the power supply to 600 V,
limiting the current at 50 mA and the power at 30 W. Run the gel for 1.5 h.
10. Turn off the power supply when the bromophenol blue dye front has
reached the anodic buffer strip. Disconnect the leads. Take the lid off the
unit and remove the electrode holder. Remove and discard the buffer strips.
11. Lift off the gel and place it in a staining tray and proceed with
desired staining method as outlined in the ‘Staining’ section of Chapter 4.
t m 80-6013-88 • p38
2.7 Troubleshooting
Vertical slab gels
Many factors affect the quality of electrophoretic separations, including: instrument assembly, preparation of the gel and
sample buffers, gel casting, the nature of the sample and its preparation, and run conditions. Some difficulties that may be
encountered during the protocol and possible explanations and solutions are described in this section.
Problem Possible cause Remedy
Gel solution leaks out Plates and spacers misaligned Realign as shown in Figure 2.2c
of sandwich during casting
Rubber gasket not seated properly Check that it is seated flat
Glass plates are chipped at edge Use unchipped plates
Gels fail to polymerize, or Solution temperature too low Bring all refrigerated gel solutions to room temperature
polymerize incompletely along prior to use. It can help to warm the gel solution to
spacers and sealing surfaces 20–25 °C after deaeration and allow it to polymerize at
or slightly above room temperature.
Oxygen concentration too high Deaerate gel solution 5–10 min with at least a water
aspirator
Insufficient or degraded catalyst Check the ammonium persulphate for freshness. Fresh
ammonium persulphate will crackle when water is added;
if it doesn’t, use a fresh bottle. Make new solutions daily.
If the polymerization problem persists, increase the
ammonium persulphate and TEMED concentration by
50%. Increasing the catalyst concentration is particularly
useful when working with low acrylamide concentrations.
Sample wells distorted, causing Air bubbles trapped under comb Remove air bubbles if present
distorted protein bands
Unreacted acrylamide continued to Rinse wells with tank buffer immediately after the comb
polymerize after comb was removed is removed
Dye front curves up (smiles) Gel is hotter in the middle than at the Use active temperature control of the SE 600 and
at the edges edges (the spacers act as heat sinks, completely submerge the gel sandwich in the
lowering the temperature at the edge stirred buffer
of the gel)
Temperature too high Reduce power settings
Dye front curves down (frowns) Air bubbles trapped between glass plates Remove air bubbles if present
at the edges at bottom of gel sandwich can be large
enough to block current flow and produce
a localized frown
Gel next to the spacers was not fully Degas solution or increase ammonium persulphate and
polymerized; current leaked down the TEMED concentration by 50%
edges of gel, producing a localized
frown at edge
Upper buffer chamber sealing gasket Check for proper installation

pinched closed at center
• p39
Protein bands fuzzy or Sample volume too high Load sample in less volume, as a tight layer in the
poorly resolved bottom of well. Height of the stacking gel beneath the
well should be at least two times the height of the
sample in the well.
Samples diffused out of well Start electrophoresis immediately after loading samples
Gel acrylamide concentration too low Tailor gel concentration to produce optimal resolution.
(proteins that separate near dye front are (Table 2.6). Use gradient gel to increase sharpness of
usually less well resolved than those lower MW bands.
farther up the gel)
Sample is degraded Keep sample on ice until mixed with SDS sample buffer
and heat in 70–100 °C water bath for no more than 3 min
Run takes longer than usual Buffers (tank or gel) too concentrated Remake solutions
or at wrong pH
Stained material concentrates %T too low to fractionate the sample Increase % acrylamide
at dye front proteins, or proteins are degraded to the
point where they are too small to resolve
Stained material concentrates %T too high, and proteins cannot Decrease % acrylamide
at top of resolving gel penetrate the matrix
Insoluble precipitates in sample Some proteins precipitate upon heating at 100 °C (seen
as staining and protein smearing at top of resolving gel).
Heat at lower temperature (60–70 °C).
Flatbed electrophoresis
No current at start of run Electrode cable not plugged in Ensure that all cables are properly connected
Dye front curves up (smiles) Cathodic buffer strip does not contact Ensure that cathodic buffer strip is centered and covers
at one edge gel at one edge entire width of gel
Dye front curves up (smiles) Inadequate cooling Ensure that thermostatic circulator is connected to
at both edges Multiphor II unit and functioning correctly
Dye front is irregular Buffer strips or ExcelGel are old Ensure that expiration dates on buffer strips and
ExcelGel have not elapsed
Bubbles under buffer strip Ensure that buffer strips are placed firmly on gel with no
air bubbles trapped beneath
Buffer strip slides out Incorrect electrode placement Ensure that electrodes are aligned over center of buffer
from under electrode strips before lowering electrode holder
t m 80-6013-88 • p40

Davis, B. J. Disc electrophoresis-II: Method and application to human
serum proteins. Ann. N.Y. Acad. Sci. 121, 404–427 (1964).
Dunn, M. J. Gel Electrophoresis: Proteins. Bios Scientific Publishers

Limited, Oxford, United Kingdom (1993).
Gallagher, S., and Smith, J. A., One-dimensional gel electrophoresis of

proteins. In Current Protocols in Molecular Biology Unit 10.2 (Ausubel,
F. A. et al., eds.), Wiley-Interscience, New York (1995).
Görg, A., et al., Biochem. Biophys. Methods 3, 273–284 (1980).

Shi, Q. One-dimensional polyacrylamide gel electrophoresis. In Gel

Electrophoresis of Proteins: A Practical Approach 3rd ed. (Hames, B. D.,
ed.), Oxford University Press, New York, pp. 1–52 (1998).
Laemmli, U. K. Cleavage of structural proteins during the assembly of the

head of bacteriophage T4. Nature 227, 680–685 (1970).
Ornstein, L. Disc electrophoresis-I: Background and theory. Ann. N.Y.

Acad. Sci. 121, 321–349 (1964).
Schägger, H., and von Jagow, G. Anal. Biochem. 166, 368–379 (1987).
Westermeier, R. Electrophoresis in Practice 2nd ed. VCH, Weinheim,

Germany (1997).
• p41
t m 80-6013-88 • p42
• isoelectric focusing of proteins
Chapter 3
Isoelectric focusing of proteins
3.0 Introduction
Isoelectric focusing (IEF) is an electrophoretic method that separates
proteins according to their isoelectric points (pI). Proteins are amphoteric
molecules; they carry either positive, negative, or zero net charge, depend-
ing on their amino acid composition and the pH of their surroundings.
The net charge of a protein is the sum of all the negative and positive
charges of its amino acid side chains and amino- and carboxyl-termini.
The isoelectric point is the specific pH at which the net charge of the
protein is zero. Proteins are positively charged at pH values below their
pI and negatively charged at pH values above their pI (Fig 3.1).
The presence of a pH gradient is critical to the IEF technique. In a pH

Fig 3.1. Net charge on a protein as a function of
pH. In this example the protein has a net charge of gradient, under the influence of an electric field a protein will move to
+2 at pH 5.5, 0 at pH 7.5 (the isoelectric point), the position in the gradient where its net charge is zero. A protein with a
and -1 at pH 8.5.
positive net charge will migrate toward the cathode, becoming progres-
sively less positively charged as it moves through the pH gradient until it
reaches its pI. A protein with a negative net charge will migrate toward
the anode, becoming less negatively charged until it also reaches zero net
charge. If a protein should diffuse away from its pI, it immediately gains
charge and migrates back to its isoelectric position. This is the focusing
effect of IEF, which concentrates proteins at their pIs and separates
proteins with very small charge differences. Because the degree of resolu-
tion is determined by electric field strength, IEF is performed at high volt-
ages (typically in excess of 1 000 V). When the proteins have reached
their final positions in the pH gradient, there is very little ionic movement
in the system, resulting in a very low final current (typically below 1 mA).
Fig 3.2. Creating a carrier ampholyte pH gradient. One method for generating pH gradients in IEF gels relies on carrier
(A) No voltage applied. (B) Ampholytes and proteins ampholytes. Carrier ampholytes are small, soluble, amphoteric molecules
move by electrophoresis when charged. (C) At
isoelectric pH, ampholytes and proteins are focused.
with a high buffering capacity near their pI. Commercial carrier ampholyte
mixtures comprise hundreds of individual polymeric species with pIs
spanning a specific pH range. When a voltage is applied across a carrier
ampholyte mixture (Fig 3.2), the carrier ampholytes with the lowest pI
(and the most negative charge) move toward the anode, and the carrier
ampholytes with the highest pI (and the most positive charge) move toward
the cathode. The other carrier ampholytes align themselves between the
extremes, according to their pIs, and buffer their environment to the corre-
sponding pH. The result is a continuous pH gradient.
IEF can be run in either a native or a denaturing mode. Native IEF is the
more convenient option, as precast native IEF gels are available in a
variety of pH gradient ranges. This method is also preferred when native
protein is required, as when activity staining is to be employed. The use
of native IEF, however, is often limited by the fact that many proteins are
• p43
protein electrophoresis • isoelectric focusing of proteins
not soluble at low ionic strength or have low solubility close to their
isoelectric point. In these cases, denaturing IEF is employed. Urea is the
denaturant of choice, as this uncharged compound can solubilize many
proteins not otherwise soluble under IEF conditions. Detergents and
reducing agents are often used in conjunction with urea for more-complete
unfolding and solubilization. Urea is not stable in aqueous solution, so
precast IEF gels are not manufactured with urea. Dried precast gels are a
convenient alternative; they have been cast, rinsed, and dried and can be
rehydrated with urea, carrier ampholytes, and other additives before use.
Although useful, carrier ampholytes have some limitations. Because the

carrier ampholyte–generated gradient is dependent on the electric field,
it breaks down when the field is removed. The pH gradients are also
susceptible to gradient drift (or cathodic drift), a phenomenon in which
there is a gradual decrease in pH at the cathodic (–) end of the gel and a
flattening out of the pH at the anodic (+) end. For this reason it is impor-
tant to not overfocus the protein, because cathodic drift will increase over
time. There can be significant batch-to-batch and company-to-company
variations in the properties of carrier ampholytes, which limits the repro-
ducibility of focusing experiments. Another problem encountered with
carrier ampholytes is their tendency to bind to the sample proteins, which
may alter the migration of the protein and render the separation of
carrier ampholytes from the focused protein difficult.
Acrylamido buffers are an alternative means to form pH gradients that

circumvent most of the limitations of carrier ampholytes. Chemically, they
are acrylamide derivatives of simple buffers and do not exhibit amphoteric
behavior. The acrylic function of an acrylamido buffer co-polymerizes
with the gel matrix and, by pouring a gel that incorporates an appropriate
gradient of acrylamido buffers, an immobilized pH gradient (IPG) is
formed (Fig 3.3). The protein sample can be applied immediately (no
prefocusing is needed). The pH gradient is stable and does not drift in an
electric field. Additionally, the gels are not susceptible to cathodic drift,
Fig 3.3. Creating an immobilized pH gradient. because the buffers that form the pH gradient are immobilized within the
(A, B, C) A gradient of acrylamido buffers in an
acrylamide solution is cast into a slab gel that is
gel matrix. Acrylamido buffers are available from Amersham Pharmacia
crosslinked to a plastic support film. (D) The gel Biotech as individual Immobiline™ species with a specific pK value (or
is washed to remove polymerization byproducts.
optimum pH buffering range), suitable for casting gradients from pH 3–10.
(E) The gel is dried for storage. (F) The pH at any
point in the gel is determined by the mixture of Because reproducible linear gradients with a slope as low as 0.01 pH
buffers crosslinked into the gel at that site. units/cm can separate proteins with pI differences of 0.001 pH units, the
resolution possible with immobilized pH gradient gels is 10–100 times
greater than that obtained with carrier ampholyte–based IEF.
IEF is best performed in a flatbed electrophoresis apparatus. This type

of apparatus allows very effective cooling, which is necessary due to the
high voltages employed for IEF. Amersham Pharmacia Biotech offers a
variety of precast gels for IEF, including ready-to-use carrier ampholyte
gels, dried IPG gels, and dried acrylamide gels ready for reswelling in a
mixture of carrier ampholytes and any other additives desired, such as
detergent and denaturants.
t m 80-6013-88 • p44
Table 3.1 lists the pH ranges available for these gels.
Table 3.1. Precast IEF gels for

Multiphor II Flatbed Electrophoresis System
Gel type
Ampholine™ PAGplate IEF
pH 3.5–9.5
pH 4.0–6.5
pH 5.5–8.5
pH 4.0–5.0
CleanGel Dry IEF
Immobiline DryPlate IEF
pH 4.0–7.0
pH 4.2–4.9
pH 4.5–5.4
pH 5.0–6.0
pH 5.6–6.6
For all gels: sample volume, 1–40 µl; number of samples/gel, 26–52; samples
are applied either by application strips or pieces.
3.1 Native isoelectric focusing

The following protocol separates proteins under native conditions over a
range from pH 3.5 to pH 9.5 on an Ampholine PAGplate pH 3.5–9.5
precast IEF gel.
3.1.1 Solutions
IEF anode solution Final concentration Amount

(1 M H3PO4, 100 ml)
Concentrated H3PO4
(phosphoric acid 14.7 M) 1M 6.8 ml
ddH2O to 100 ml
IEF cathode solution

(1 M NaOH, 100 ml)
NaOH
(sodium hydroxide FW 40.00) 1M 4.0 g
ddH2O to 100 ml
Store up to 1 wk at room temperature.
• p45

• IEF anode solution (1 M H3PO4)
• IEF cathode solution (1 M NaOH)
• Ampholine PAGplate pH 3.5–9.5
• IEF electrode strips
• Multiphor II Flatbed Electrophoresis Unit
• MultiTemp III Thermostatic Circulator
• IEF sample applicator strip
• IEF sample application pieces
• EPS 3501 XL or EPS 3501 high-voltage power supply (capable of
delivering 3 500 V while limiting both current and power)
3.1.3 Procedure
Sample preparation
1. Dissolve the sample in water to a concentration of 0.5–10 mg/ml for

Coomassie Blue staining. Buffers and salts should not be present at a
concentration greater than 50 mM. Samples containing insoluble material
should be filtered or centrifuged before use.
2. Connect the Multiphor II to the thermostatic circulator and set the

temperature to 10 ºC. Turn on the thermostatic circulator 10 min before
starting the analysis.
3. Pipette about 1 ml of kerosene or light paraffin oil onto the cooling

plate of the electrophoresis unit.
4. Remove the Ampholine PAGplate from its package and position it in the
center of the cooling plate, allowing the kerosene or oil to spread evenly
underneath the gel. Make sure no bubbles are trapped beneath the gel.
The gel can be used in one piece or, depending on the number of samples,
cut into portions with scissors. If this is done, current and power limits
should be reduced accordingly (e.g. if only half a gel is to be run, current
and power limits should be set at 25 mA and 15 W, respectively, rather
Fig 3.4. Soak the electrode strip in anolyte than 50 mA and 30 W). Unused portions of gel can be wrapped in plastic
or catholyte. or placed in sealed plastic bags and stored at 4 °C until use.
5. Use scissors to cut off the ends of the electrode strips that protrude
beyond the ends of the gel.
6. Soak one IEF electrode strip in IEF anode solution using approxi-
mately 3 ml of solution. Remove excess solution with blotting paper
(Fig 3.4).
7. Repeat step 6 with a second IEF electrode strip using IEF cathode
solution.
Fig 3.5. Applying an electrode strip near the anode. 8. Apply the electrode strips over the long edges of the gel. The electrode
strip soaked with the anodic solution should be toward the anodic (+)
side of the cooling plate (Fig 3.5).
t m 80-6013-88 • p46
Pre-run the gel (optional)
the electrode strips. Lower the electrode holder so that the electrodes rest
on the electrode strips. Connect the two electrodes to the base unit and
place the lid on the unit.
10. Connect the leads to the power supply. Set the power supply to 1 500 V,
limiting the current at 50 mA and the power at 30 W. Run the gel for 15 min.
The voltage should start out between 300–600 V and rise steadily toward
1 500 V during the pre-run step. Pre-running the gel is optional, but can
result in a higher-quality separation.
11. Turn off the power supply and disconnect the leads. Take the lid off
the unit and remove the electrode holder.
12. Lay the IEF applicator strip across the gel toward either the anodic or
cathodic edge. Check that the contact between the gel and the applicator
strip is uniform.
The optimal position for sample application varies with sample type and
must be determined empirically. This is best done using sample applica-
Fig 3.6a. Placing sample application pieces across tion pieces, which are 5 × 10 mm pads of absorbent material that can be
the gel.
placed in multiple positions on a single gel (Fig 3.6a).
13. Pipette the samples or standards into the wells in the applicator
strip or onto the sample application pieces. Use 5–20 µl sample volumes
(Fig 3.6b).
14. Place the electrode holder on the Multiphor base and align the elec-
trodes over the center of the electrode strips (Fig 3.7). Lower the electrode
holder so that the electrodes rest on the electrode strips. Connect the two
electrodes to the base unit and place the lid on the unit.
15. Connect the leads to the power supply. Set the power supply to 1 500 V,
limiting the current at 50 mA and the power at 30 W. Run the gel for 1.5 h.
Fig 3.6b. Pipetting samples into the applicator
strip wells. Note: Run conditions and buffers will vary depending on pH range of the
Ampholine PAGplate used. Please consult the instruction manual for
specific details.
the unit and remove the electrode holder. Lift the gel off the cooling plate
and place in a staining tray and proceed with Coomassie Blue or silver
staining as outlined in Chapter 4.
Fig 3.7. Positioning the electrode holder over the

electrode strip.
• p47
3.2 Denaturing isoelectric focusing

In some cases it is advantageous to perform IEF in the presence of 8 M
urea. This denaturant renders some proteins more soluble under IEF
conditions, allowing the analysis of samples that cannot be separated
under native conditions.
The following protocol separates proteins under denaturing conditions in

a range from pH 3 to pH 10. A dried polyacrylamide gel (CleanGel IEF)
is rehydrated with the IEF solution before electrophoresis.
3.2.1 Solutions
Denaturing IEF rehydration solution Final concentration Amount

(8 M urea, 7.4% v/v Pharmalyte™
carrier ampholyte pH 3–10, 10.5 ml)
Urea (FW 60.06) 8M 5.04 g
Pharmalyte 3–10 carrier ampholyte mixture 7.4% (v/v) 780 µl
ddH2O to 10.5 ml
If desired, a reducing agent (60 mM dithiothreitol [DTT]) and/or a detergent

(0.5% (w/v) Triton X-100 or CHAPS) may be added as well.

• Denaturing IEF rehydration solution, pH 3–10
• CleanGel IEF (dried polyacrylamide gel on plastic backing)
• Filter paper
• Gel Pool™ rehydration tray
• Rotary laboratory shaker
• EPS 3501 XL high-voltage power supply
3.2.3 Procedure
Gel rehydration
1. Open the gel package and remove the dry gel.
The dry gel can be used in one piece or, depending on the number of
samples, cut into portions with scissors. Unused portions of gel can be
wrapped in plastic or placed in sealed plastic bags and stored at -20 °C
Fig 3.8. Example of isoelectric focusing using
until use.
CleanGel IEF.
2. Select the appropriate-sized chamber of the rehydration tray. Clean the
rehydration tray with distilled or deionized water and dry with tissue
paper. Pipette the rehydration solution into the chamber. For a full-size
gel, use 10.4 ml. For portions of the gel, reduce the volume accordingly
(e.g. use 5.2 ml for half a gel).
The rehydration solution should include the components desired for the
separation: urea, carrier ampholytes, plus any detergents or reductants.
t m 80-6013-88 • p48
3. Set the edge of the gel film, with the gel surface facing down, into the
rehydration solution and slowly lower the rest of the gel into the solution.
Lift the film at the edges with forceps and slowly lower it down again to
ensure an even distribution of the liquid and to remove air bubbles. Place
the rehydration tray on a rotary laboratory shaker and shake gently.
Allow the gel to rehydrate 4 h to overnight.
When including urea, overnight rehydration ensures complete absorption.
Sample preparation
4. Dissolve or dilute the sample into denaturing IEF rehydration solution

(the composition of the sample solution should be as similar as possible
to the composition of the rehydration solution). If the gel is to be stained
with Coomassie Blue, the protein concentration in the sample should be
1–3 mg/ml. Buffers and salts should not be present at a concentration
greater than 50 mM. Samples containing insoluble material should be
filtered or centrifuged before use.
5. Connect the Multiphor II Electrophoresis Unit to the thermostatic

circulator and set the temperature to 15 ºC. Turn on the thermostatic
circulator 10 min before starting the analysis.
6. Pipette about 1 ml of kerosene or oil onto the cooling plate of the

electrophoresis unit.
7. Remove the gel from the rehydration tray and carefully dry the
surface by gliding the edge of a sheet of filter paper across the surface.
8. Position the gel in the center of the cooling plate, allowing the
kerosene or oil to spread evenly underneath the gel. Make sure no
bubbles are trapped beneath the gel (Fig 2.23).
Pre-run the gel
9. Place the electrode holder with the IEF electrodes on the electrophoresis
unit and align the electrodes so that they rest on the outer edges of the gel.
Electrode wicks are not necessary. Lower the electrode holder into place.
Connect the two electrodes to the base unit and place the lid on the unit.
10. Connect the leads to the power supply. Follow the recommended
settings given in Table 3.2. Pre-run the gel for 20 min.
the unit and remove the electrode holder.
12. Lay the IEF applicator strip across the gel toward either the anodic or
cathodic edge. Check that the contact between the gel and the applicator
strip is uniform.
• p49
tion pieces, which are 5 × 10 mm pads of absorbent material that can be
placed in multiple positions on a single gel (Fig 3.9a).
13. Pipette the samples or standards into the wells in the applicator strip or
onto the sample application pieces. Use 5–20 µl sample volumes (Fig 3.9b).
14. Place the electrode holder on the Multiphor base and align the elec-
trodes so that they rest on the outer edges of the gel. Lower the electrode
holder into place. Connect the two electrodes to the base unit and place
the lid on the unit (Fig 3.9c).
15. Connect the leads to the power supply. Run the gel according to the
Fig 3.9a. Placing sample application pieces recommended settings given in Table 3.2.
across the gel.
Table 3.2. Running conditions for denaturing IEF

Step Voltage (V) Current (mA)* Power (W)* Time (min)
Pre-run 700 12 8 20
Sample entrance 500 8 8 20
Isoelectric focusing 2 000 14 14 90
Band sharpening 2 500 14 18 10
*If only a portion of the gel is run, current and power limits should be reduced accordingly for the run
(e.g. if only half a gel is to be run, current and power limits should be set at 7 mA and 7 W, respectively,
rather than 14 mA and 14 W).
Fig 3.9b. Pipetting samples into applicator

strip wells.
16. When electrophoresis is complete, turn off the power supply and
disconnect the leads. Take the lid off the unit and remove the electrode
holder. Lift gel into a staining tray and proceed with the desired staining
protocol outlined in Chapter 4.
3.3 Isoelectric focusing using immobilized

pH gradient (IPG) gels
Figure 3.10 illustrates the separation of bovine erythrocyte carbonic
anhydrase using an Immobiline DryPlate IEF, pH 4.0–7.0.
Fig 3.9c. Position the electrode holder over the 3.3.1 Materials and equipment
electrode strip.
• DryPlate reswelling cassette and clamps
• Immobiline DryPlate, pH 4.0–7.0 (dry, precast polyacrylamide gel
containing preformed, immobilized pH gradient)
• 10 ml pipette
• Repel-Silane ES
• EPS 3501 XL high-voltage power supply
• Roller
t m 80-6013-88 • p50
3.3.2 Procedure
Assemble the reswelling cassette

pI
1. Wash the glass plates with detergent, rinse with distilled or deionized
water, and dry with a paper towel.
6.67
2. Swab the gasketed glass plate with Repel-Silane ES to prevent the gel
from sticking to the plate. Rinse off excess with water and air dry.
3. Remove the DryPlate from the freezer. Wearing gloves, remove the gel
from the package. Be careful not to damage the gel while removing it
from the package: The gel faces the aluminum foil side of the package.
6.11
6.06 The gel can be used in one piece depending on the number of samples, or
5.97
cut into portions with scissors. If this is done, current and power limits
5.87 should be reduced accordingly. Unused portions of gel can be wrapped in
5.73 plastic or placed in sealed plastic bags and stored at 4 °C.
4. Apply small drops of distilled water on the outer edges and middle of
the plain glass plate. Carefully lay the gel onto the glass plate, support
5.46
film side facing down. Roll the gel flat to remove air bubbles and to
ensure good contact with the plate. Blot away any excess water that is
squeezed out.
5.12 5. Clamp the glass plates together with rubber-edged clamps (Fig 3.11),
making sure that the V-indentations and support film are on the inside.
Reswell the gel
6. Fill the cassette with 20 ml of reswelling solution, using a 10 ml

pipette.
For water-soluble proteins, distilled water can be used. Alternatively, gels

can be rehydrated with additives, such as urea and nonionic detergents.
See the DryPlate instructions for further information.
7. Reswell the gel for 1–2 h when using water, 15–18 h when using urea
Fig 3.10. IPG analysis of bovine and nonionic detergents.
erythrocyte carbonic anhydrase.
8. Remove the clamps and disassemble the mold by gently prying the
plates apart with a long razor blade.
Sample preparation
9. Dissolve the sample in water to a concentration of 0.5–10 mg/ml for

Coomassie Blue staining. Buffers and salts should not be present at a
concentration greater than 50 mM. Samples containing insoluble material
should be filtered or centrifuged before use.
Fig 3.11. Clamp together the glass plates of the

reswelling cassette.
• p51
10. Connect the Multiphor II to the thermostatic circulator and set the
temperature to 10 ºC (20 ºC if using urea concentrations above 4 M).
Turn on the thermostatic circulator 10 min before starting the analysis.
11. Pipette about 1 ml of kerosene or oil onto the cooling plate of the
electrophoresis unit.
12. Orient the gel so that the notch at the lower-left corner of the film
faces the anodic (+) electrode. Position the gel in the center of the cooling
plate, allowing the kerosene or oil to spread evenly underneath the gel.
Make sure no bubbles are trapped beneath the gel.
13. Use scissors to cut off the ends of the electrode strips that protrude
beyond the ends of the gel.
14. Soak IEF electrode strips in water. Remove excess solution with
blotting paper.
15. Apply the electrode strips over the long edges of the gel.
16. Lay the IEF applicator strip across the gel toward either the anodic
or cathodic edge. Check that contact between the gel and the applicator
strip is uniform.
tion pieces, which are 5 × 10 mm pads of absorbent material that can be
placed in multiple positions on a single gel (Fig 3.12).
17. Pipette the samples or standards into the wells in the applicator
Fig 3.12. Placing sample application pieces across
strip or onto the sample application pieces. Use 5–20 µl sample volumes.
the gel.
(Fig 3.13).
the electrode strips. Lower the electrode holder into place. Connect the
two electrodes to the base unit and place the lid on the unit.
19. Connect the leads to the power supply. Set the power supply to
3 500 V, limiting the current at 5 mA and the power at 15 W. Run the
gel for 2–4 h.
Note: The run times will vary for different gels, depending on the pH
range of the gel, and must be determined empirically.
Fig 3.13. Pipetting samples into applicator
strip wells. the unit and remove the electrode holder. Lift the gel off the cooling plate
and place in a staining tray and proceed with Coomassie Blue or silver
staining as outlined in Chapter 4.
t m 80-6013-888 • p52
3.4 Troubleshooting
Low or no current Poor contact between electrodes and Make sure that electrode strips are correctly placed.
electrode strips Low current is normal in IEF; gel currents will drop to
1–5 mA.
Current rises during the run Electrode strips or electrodes are mixed up Check polarity; check pH of electrode strips
Condensation Insufficient cooling Check coolant flow and temperature
Sparking on gel Drying out of gel close to electrodes Incorrect electrode solutions; use recommended solutions
Excessive power input Check power supply settings
Excess moisture Remove excess moisture by gently drawing a clean sheet

of filter paper across gel surface
Wavy bands Poor electrode contact Check electrode contact
Incorrect electrode solutions Use recommended solutions
Uneven cooling across gel Remove all air bubbles between gel backing sheet and
cooling platform
Debris in sample Centrifuge to remove particulates
Sample too concentrated Load less protein
Excessive salt in sample Desalt samples
Fuzzy bands Focusing was not long enough Increase focusing time
Streaking of the bands Sample may contain too high a Decrease their concentration
concentration of salts, buffers, or other
small charged molecules

Guide to Protein Purification. Methods in Enzymology Vol. 182
(Deutscher, M. P., ed.), Academic Press, San Diego (1990).
Righetti, P. G. et al. Conventional isoelectric focusing in gel slabs, in

capillaries, and immobilized pH gradients. In Gel Electrophoresis of
Proteins. A Practical Approach 3rd ed. (Hames, B. D., ed.). Oxford
University Press, New York, pp. 127–187 (1998).
Westermeier, R. Electrophoresis in Practice 2nd ed. VCH, Weinheim,

Germany (1997).
• p53
tm 80-6013-88 • p54
• analysis of gels
Chapter 4
Analysis of gels
Once electrophoresis is complete, the gel must be analyzed to obtain
information on the position and quantity of each protein. Because most
proteins are not directly visible, the gel must be processed to determine
the location and amount of the separated proteins. The most common
analytical procedure is staining. Proteins are usually stained with silver or
Coomassie Blue. Once the gel is stained, it can be photographed or dried
on a backing for a record of the position and intensity of each band and
then analyzed.
The following sections outline basic protocols for Coomassie Blue staining,
silver staining, gel drying and storage, gel documentation, and estimation
of molecular weight.
4.1 Staining gels with Coomassie Brilliant Blue

Detection limit: 0.1–0.5 µg of protein
Coomassie Blue staining is based on the binding of the dye Coomassie

Brilliant Blue R250, which binds nonspecifically to virtually all proteins.
Although Coomassie Blue staining is less sensitive than silver staining, it is
widely used due to its convenience. The gel is soaked in a solution of the
dye. Any dye that is not bound to protein diffuses out of the gel during
the destain steps. Coomassie Blue binds to proteins approximately stoi-
chiometrically, so this staining method is preferable when relative amounts
of protein need to be determined by densitometry. For most SDS and
native gels, separated proteins can be simultaneously fixed and stained in
the same solution. The gel is then destained to remove the background
prior to drying and documenting. The proteins are detected as blue bands
on a clear background. When staining IEF gels with Coomassie Blue, the
gel is first fixed in a trichloroacetic acid solution. This leaches out the
carrier ampholytes, which would otherwise produce background staining.
When staining small peptides (Mr <10 000), the gel is first fixed in a solu-
tion containing glutaraldehyde to cross-link the peptides and prevent them
from diffusing out of the gel during subsequent staining steps.
• p55
protein electrophoresis • analysis of gels
4.1.1 Coomassie Blue staining stock solutions

Always wear gloves and use double-distilled, deionized, or other high-quality water.
Danger! TCA is a strong acid and very Trichloroacetic acid

fixing solution (for IEF gels) Final concentration Amount
corrosive. Use proper safety equipment
(20% (w/v) trichloroacetic acid, 500 ml)
when handling and use TCA-resistant
containers for staining. Trichloroacetic acid (FW 163.4) 20% 100 g
ddH2O to 500 ml
Glutaraldehyde fixing solution (for visualizing proteins with Mr <10 000)

(0.2% (v/v) glutaraldehyde, 30% (v/v) ethanol, 0.2 M sodium acetate, 500 ml)
25% glutaraldehyde 0.2% 4 ml
Ethanol 30% 150 ml
Sodium acetate trihydrate (FW 136.1) 0.2 M 13.61 g
ddH2O to 500 ml
Use immediately.
Coomassie Blue staining solution

(0.025% Coomassie Brilliant Blue R250, 40% (v/v) methanol,
7% (v/v) acetic acid, 2 l)
Coomassie Brilliant Blue R250 0.025% 0.5 g
Methanol 40% 800 ml
Stir until dissolved. Filter. Then add:
Acetic acid 7% 140 ml

ddH2O to 2 l
Destain solution I
(40% (v/v) methanol, 7% (v/v) acetic acid, 1 l)
Methanol 40% 400 ml
ddH2O to 1 l
Store at room temperature.
Destain solution II
(7% (v/v) acetic acid, 5% (v/v) methanol, 10 l)
Methanol 5% 500 ml
ddH2O to 10 l
Store at room temperature.
t m 80-6013-88 • p56

• Trichloroacetic acid fixing solution (required only for IEF gels)
• Glutaraldehyde fixing solution (required only for Tris-tricine gels)
• Coomassie Blue staining solution
• Destain solution I
• Destain solution II
• Covered tray
• Laboratory shaker or rocker
• Hoefer Processor Plus (optional—see section 4.1.4)
4.1.3 Standard Coomassie Blue protocol

Perform staining at room temperature. Covered plastic trays work well
and minimize exposure to methanol and acetic acid vapors. When covers
are not used, these procedures should be done in a fume hood.
When staining conventional SDS or native gels, skip ahead to step 2.

A fixing step is not required for these gels.
1. IEF gels: Submerge the gel in trichloroacetic acid fixing solution.

Shake slowly on a laboratory shaker or rocker for 30–60 min. Replace
the trichloroacetic acid fixing solution with destain solution I and shake
slowly for 3 min.
Note: Do not leave a gel in trichloroacetic acid fixing solution for more
than 60 min.
Gels used for separating proteins and peptides Mr <10 000: Submerge the
gel in glutaraldehyde fixing solution. Shake slowly on a laboratory shaker
or rocker for 30–60 min.
2. For conventional SDS and native gels, start with this step: Submerge
the gel in enough Coomassie Blue staining solution that the gel floats
freely in the tray. Shake slowly on a laboratory shaker or rocker for 4 h
to overnight.
The amount of time required to stain the gel depends in part on the
thickness of the gel. A 0.75-mm-thick gel will stain faster than a 1.5 mm
gel and may be completely stained in an hour.
Note: If using the Hoefer Processor Plus for automated staining, see
section 4.1.4.
3. Replace the staining solution with destain solution I. Shake slowly

30 min. This removes the bulk of the excess stain.
4. Remove destain solution I and replace with destain solution II. Change
the destain solution II periodically until the gel background is clear. Alter-
natively, the addition of a paper laboratory wipe to one corner of the stain-
ing tray will help remove Coomassie Blue from the gel without changing
• p57
the destain solution, minimizing the waste volume generated. Replace the
wipes when they are saturated with dye. Use caution, however, because
excessive destaining will lead to loss of band intensity.
5. Store the gel in destain solution II. To minimize cracking, add 1%

glycerol to the last destaining before drying the gel.
4.1.4 Automated Coomassie Blue staining

Use the Hoefer Processor Plus to automate the gel staining procedure,
performing all staining and destaining steps unattended. Although
Coomassie staining is a simple procedure, automation offers the benefit
of allowing the user to do other work without interruption and return to
Fig 4.1. Processor Plus with large gel staining tray.
a stained (and destained) gel, often the next morning. To use, set up the
Processor Plus with bottles containing the staining reagents and choose
a preprogrammed protocol for Coomassie staining. After starting, the
Processor Plus delivers the solutions to the tray, rocks the gels gently,
empties the tray, and continues through the complete procedure. See
Table 4.0 for a list of preprogrammed protocols for the Processor Plus.
For more-detailed information, see the technical brochure “Automated

Staining of Polyacrylamide Gels with the Hoefer Processor Plus”
(80-6343-34).
Fig 4.2. 4–20% gradient gel stained with 4.2 Silver staining
Coomassie Blue.
Detection limit: 1–5 µg of protein
Silver staining is the most sensitive method for permanent visible staining
of proteins in polyacrylamide gels. This sensitivity, however, comes at the
expense of high susceptibility to interference from a number of factors.
Precise timing, high-quality reagents, and cleanliness are essential for
reproducible, high-quality results. In silver staining, the gel is impreg-
nated with soluble silver ions and developed by treatment with formalde-
hyde, which reduces silver ions to form an insoluble brown precipitate
of metallic silver. This reduction is promoted by protein. There are many
variations of the silver staining process. The method described here is
based to the method of Heukeshoven and Dernick (1985) and has been
selected for overall convenience, sensitivity, reproducibility, and speed.
Note: This silver staining method is available as the PlusOne Protein

Silver Staining Kit (17-1150-01). The use of a silver staining kit provides
the convenience of pre-measured reagents and more consistent quality.
Wear gloves and use only glass-distilled water. Glass staining trays are
particularly useful because they are easy to clean. All steps can be done
at room temperature.
t m 80-6013-88 • p58
4.2.1 Silver staining stock solutions
Silver stain fixing solution Final concentration Amount

(40% (v/v) ethanol, 10% (v/v) acetic acid, 1 l)
Ethanol, absolute 40% 400 ml
Acetic acid, glacial 10% 100 ml
Distilled or deionized water to 1 l
Sensitizing solution
(30% (v/v) ethanol, 6.8% (w/v) sodium acetate, 0.2% (w/v) sodium thiosulphate,
0.125% (v/v) glutaraldehyde, 1 l)
Sodium acetate, anhydrous (FW 82.03) 6.8% 68 g
Sodium thiosulphate,
pentahydrate (FW 248.18) 0.2% 2g
Store stock solution without glutaraldehyde at room temperature for up to 2 mo.
Within 1 h of use, add:
25% glutaraldehyde 0.125% 0.5 ml per

100 ml of
solution used
Silver solution
(0.25% (w/v) silver nitrate, 0.015% (v/v) formaldehyde, 1 l)
Silver nitrate (FW 169.87) 0.25% 2.5 g
Store stock solution without formaldehyde in a dark bottle at room temperature for up to 2 mo.
37% formaldehyde 0.015% 40 µl per

100 ml of
solution used
Developing solution
(2.5% (w/v) sodium carbonate, 0.0074% (v/v) formaldehyde, 1 l)
Sodium carbonate,
anhydrous (FW 105.99) 2.5% 25 g
Distilled or deionized water to a total
volume of 1l
Store stock solution without formaldehyde at room temperature for up to 2 mo.
37% formaldehyde 0.0074% 20 µl per

100 ml of
solution used
Stop solution
(1.5% (w/v) Na2EDTA, 1 l)
Na2EDTA (ethylenediaminetetraacetic acid,
disodium salt) (FW 372.24) 1.5% 15 g
Preserving solution
(30% (v/v) ethanol, 4% (v/v) glycerol, 1 l)
Glycerol 4% 40 ml
• p59

• Silver staining fixing solution
Table 4.0 Processor Plus capabilities • Sensitizing solution
• Silver solution
The Processor Plus has a total of nine • Developing solution
preprogrammed protocols including: • Stopping solution
• Preserving solution
Protein Coomassie staining—SDS and native
• Covered tray
Protein Coomassie staining—IEF
• Laboratory shaker or rocker
Protein silver staining—SDS and native
• Hoefer Processor Plus (optional)
Protein silver staining—IEF
DNA silver staining 4.2.3 Silver staining protocol
For more information on automating silver Silver staining is a complex, multistep process, and many variables can
staining, see the technical brochure “Auto- influence the results. High-purity reagents and precise timing are essential
mated Staining of Polyacrylamide Gels with for reproducible, high-quality results. Impurities in the gel and/or the water
the Hoefer Processor Plus” (80-6343-34). used for preparing the staining reagents can cause poor staining results.
Automation of the silver staining process with the Hoefer Processor Plus
and the use of PlusOne™ Silver Staining Kits eliminate most of the vari-
ables associated with silver staining. Precise control of timing and the use
of standard, prepackaged reagents provide exceptional reproducibility
and free the user from the necessity to be present throughout this once-
tedious procedure. The following protocol is easily preformed with the
Processor Plus or can be carried out manually using trays on a shaker.
Process the gel(s) according to Table 4.1. Use 250 ml of each solution per
gel for standard (14 × 16 cm) gels. Use 100 ml of each solution per gel
for mini-format (8 × 10 cm) gels. The timing of some of the steps differs
according to the thickness of the gel as indicated in the table. Shake
slowly on a laboratory shaker or rocker.
Table 4.1. Silver staining protocol

Time for Time for
Solution 1-mm-thick gel 1.5-mm-thick gel
Silver staining fixing solution* 30 min 30 min

Sensitizing solution 30 min 30 min
Fig 4.3. Example of a silver stained Distilled or deionized water 3 × 5 min 3 × 10 min
ExcelGel 12.5%. Silver solution 20 min 30 min
Distilled or deionized water 2 × 1 min 2 × 1 min
Developing solution 3–5 min† 5–10 min†
Stopping solution 10 min 10 min
Distilled or deionized water 3 × 5 min 3 × 5 min
Preserving solution‡ 30 min 30 min
*The gel(s) can be left in this solution until a convenient time for completing the procedure (up to 1 wk).
†
Monitor development and change the solution when protein bands are visible and the background is just
starting to darken.
‡
Gels can be stored in this solution. The glycerol in the preserving solution will prevent the gels from
cracking when dried.
Note: This protocol gives the best results when applied to standard SDS and native gels. High levels of
background staining can be expected on IEF gels unless extra steps are taken to remove interfering carrier
ampholytes before staining. When staining IEF gels, the silver staining protocol outlined above should be
preceded by an additional 30-min fixing step in trichloroacetic acid fixing solution. For solution recipe see
Coomassie Blue staining solutions in section 4.1.1. Additional washing between the sensitizing step and
the silver step may also be necessary.
t m 80-6013-88 • p60
4.3 Gel drying and storage

4.3.1 Storage
Gels can be stored either wet or dried. To store wet gels, simply place the
wet gel onto a sheet of plastic wrap and fold the wrap over the gel. This
permits handling the gel without the risk of breakage. Insert the wrapped
gel into a plastic bag and seal at 4 ºC up to 1 yr.
4.3.2 Drying gels by vacuum

For vacuum drying on a paper support, use Hoefer GD 2000 Vacuum
Gel Dryer System (Fig 4.4) or equivalent. Place the destained gel onto a
sheet of filter paper of the same size. This is placed on a larger sheet of
filter paper covering the metal screen on the dryer platen. Cover the top
of the gel with plastic wrap and then lower the silicone dryer cover flap.
Apply vacuum to seal the flap, then turn on the heater and timer.
During vacuum drying, the gel will feel cold relative to the surrounding
platen if it is not completely dry. When the temperature of the gel is the
same as that of the platen, the gel is dry and the vacuum and dryer can
be turned off.
Fig 4.4. Hoefer GD 2000 Vacuum Gel Dryer System.

Gels may crack if the vacuum is released before the gel is completely dry,
if the vacuum is poor due to a leak in the system, or if the cold trap is
full. Some pumps, such as the Hoefer diaphragm pump, do not require a
cold trap and can be attached directly to the dryer for simpler, more reli-
able operation. The percentage of acrylamide and gel thickness also influ-
ence gel cracking. In general, gels ≤0.75 mm thick dry without cracking
regardless of the acrylamide percentage. With gels thicker than 0.75 mm,
the following guidelines are recommended: Up to 12.5% acrylamide, dry
the gel without any special treatments. For >12.5%, add 1–2% glycerol
to the final destain or storage solution prior to drying. For thick (>1.0
mm) or for high-percentage (>12.5%) gels, place gels back into destain I
containing 2% glycerol for 30–60 min before drying to dehydrate and
shrink the gel. This reduces cracking by minimizing the shrinkage that
normally occurs as gels dry.
4.3.3 Air drying using Easy Breeze™

To air dry, place the gel between two sheets of porous cellophane and
lock into the drying frame. Insert the frame into the air dryer and turn
on fan and heater. Moisture evaporates through the cellophane, leaving
a flat, easy-to-store gel with a clear background. Gels dry in less than
2 h. (Fig 4.5).
Fig 4.5 Hoefer SE 1200 Easy Breeze Air Gel Dryer.
• p61
4.4 Documentation
Although gels are easy to store, it is more convenient to store a photo-
graph, printout, or scan of a gel. Numerous methods and technology
exist for capturing images for subsequent analysis or storage.
4.4.1 Photography
Photography using instant film is convenient and simple. The initial cost
of the camera is relatively low; however, pictures cannot be further manip-
ulated. Film is available to make both positive prints and image negatives.
1 2 3 4 5 6 7
4.4.2 Densitometer
Densitometry generates a peak diagram (densitogram) from which the
area under each peak can be determined, representing the intensity of
bands in the gel.
4.4.3 Scanners and digital cameras

In recent years many laboratories have acquired digital documentation
systems that capture and store images of gels. Instruments include digital
CCD cameras, such as the ImageMaster™ VDS photo documentation
system, or scanners (such as the ImageMaster Desktop Scanner). The
advantages of digital image acquisition include speed and the ease of
direct quantitative analysis of the image with software that automatically
calculates molecular weight and band intensity. Furthermore, the image
can be annotated for recordkeeping and publication.
Fig 4.6. Digital image of silver stained gel.

4.5 Estimation of protein molecular weights
by SDS gel electrophoresis
Estimating the size or molecular weight of a protein is relatively straight-
forward with SDS gels. The general procedure is to separate a set of
standards (proteins with known molecular weights) in parallel with the
unknown or sample protein. The standards are used to generate a curve
correlating molecular weight and migration in the gel, from which the
molecular weight of the unknown sample can be determined. The gel
concentration should be chosen so that the standards produce a linear
curve in the region of the unknown.
The following is the basic molecular weight calculation procedure.

Fig 4.7. Density profiles of lanes 5, 6, 7 from image
• Processed SDS gel with standards (either gradient or
in Figure 4.6.
single-concentration gel)
• Calculator capable of two-variable statistics, or a
computer with spreadsheet or graphing software
• Ruler with 0.1 cm markings (included, Fig 4.8)
• Rf calculator overlay (optional—included, Fig 4.8)
• Log-Linear graph paper
t m 80-6013-88 • p62
4.5.2 Procedure
1. Determine the migration distance into the gel or relative mobility of
the standard and unknown proteins using the overlay template provided
in Figure 4.8. Transfer the data to Table 4.2 to complete the calculations.
Relative mobility is defined as:
Rf = distance migrated by protein

distance migrated by marker
Usually, the dye front serves as the relative mobility marker. Alternatively,
a low-molecular-weight standard protein can serve as the relative mobil-
ity marker. Frequently, with gradient gels the dye front is diffuse or will
run off the bottom of the gel, and selecting an internal protein marker is
useful. Last, one of the simplest approaches to estimating molecular
weights simply uses migration distance into the gel without converting to
a relative mobility. The use of an internal marker (dye or protein)
corrects for lane-to-lane differences in mobility.
2. Plot the log protein size (y-axis) versus mobility (x-axis).
With gradient gels, an alternative “x-axis” is frequently used. Plotting the

log molecular weight (y) versus log%T (x), produces very good linearity
(Hames, 1998). Simply using migration distance or relative mobility for
the x-axis, however, generally produces adequately straight calibration
lines and is much simpler to determine.
Table 4.2. Protein standards with approximate molecular weights

Standard Size Log size Migration distance Relative mobility
Phosphorylase b 94 000 4.9731
Albumin 67 000 4.8261
Ovalbumin 43 000 4.6335
Carbonic anhydrase 30 000 4.4771
Trypsin inhibitor 20 100 4.3032
α-lactalbumin 14 400 4.1584
Unknown #1
Unknown #2
• p63
Fig 4.8.
cm rule and relative mobility calculator
t m 80-6013-88 • p64
Figure 4.9 illustrates the mobility of standard proteins at several poly-

acrylamide gel concentrations. Note that the curves are linear only over
Protein standards mobility vs % acrylamide a limited range of molecular weights. In contrast, gradient gels display
20 linear mobility over a wide range of protein sizes on a single gel
0
(Figs 4.10 and 4.11).
Log molecular weight
10
3. Use a calculator or a computer program to perform linear regression
5%
0
7.5%
of the data.
80
60 10%
4. Once the regression line has been calculated, use the equation of the
40 12.5%
15% line to estimate the size of the unknown protein.

20 0 0.2 0.4 0.6 0.8 1.0
Rf
The purpose of plotting the data and performing the regression is to
generate a linear curve through the standards so that the size of the
Fig 4.9. Calibration curves of protein standards at
five concentrations of acrylamide. Data taken from unknown can be estimated. Thus, choose a region of the plotted data
Smejkal and Gallagher (1994) with the end of the that is reasonably linear for performing the regression. Use Figure 4.9
gel used as the relative mobility marker.
to estimate the concentration of acrylamide to use to get a linear stan-
dard curve in the region of the unknown. Alternatively, use gradient
5–20% gradient gel gels for wide-range linearity.
200
The general equation of a straight line is:
100
Log molecular weight
80
60
y = mx + b
40
where m is the slope and b is the y-intercept. In this case, the equation
20
becomes:
10 log molecular weight = (slope)(mobility) + y-intercept

0.1 0.3 0.5 0.7 0.9
Rf
Most scientific calculators will generate the required parameters automat-
Fig 4.10. Calibration curves of protein standards ically as the log molecular weight (y data) and the mobility (x data) are
taken from the gel in Figure 4.11 below. Rf marker
was the end of the gel.
entered. Determining the size of an unknown becomes straightforward
simply by placing the unknown or sample protein mobility (x) into the
kD kD equation and calculating y (log molecular weight).
205
116
97
66 66
45 45
36
29
24 29
20
14
Rf
Fig 4.11. 5–20% acrylamide gradient gel. 0.75-

mm-thick SDS gel was separated overnight at 4 mA
and stained with Coomassie Blue. Outside lanes
contain protein standards with their sizes listed in
kilodaltons.
• p65
4.6 Troubleshooting
Coomassie stain
Bands poorly stained Insufficient staining time Increase staining time
Blue background Gel insufficiently destained Increase destaining time or changes of destain
Silver stain
Bands develop poorly or not at all Staining solutions not prepared or timed correctly Prepare solutions again
Ambient temperature below 20 °C Lengthen development time
Background is excessively dark Water impure Use distilled or deionized water; use water
with a resistivity of ≥ 5 MΩ
Interfering substances not completely washed out Increase fixing step
Washing steps too short Lengthen washing step after sensitization
Development too long Shorten development time
Ambient temperature above 27 °C Shorten development time
Bands lighter than background Overloading Reduce amount of protein loaded on gel
Smearing or blackening in lanes in Overloading Reduce amount of protein loaded on gel

which protein is loaded
Dark streaks and spots Dirt and fingerprints Thoroughly clean gel equipment and glass
plates; use gloves when handling gels

Heukeshoven, J., and Dernick, R., Electrophoresis 6, 103–112 (1985).
Merril, C. R., and Washart, K. M., in Gel Electrophoresis of Proteins:

A Practical Approach 3rd ed. (Hanes, B. D., ed.), Oxford University
Press, New York. pp. 53–91 (1998).
Merril, C. R., et al., Methods Enzymol. 104, 441–447 (1984).
Morrissey, J. H., Anal. Biochem. 117, 307–310 (1981).
Oakley, B. R., et al., Anal. Biochem. 105, 361–363 (1980).
Sasse, J., and Gallagher, S. R., in Current Protocols in Molecular Biology

Unit 10.6 (Ausubel, F. A., et al., eds.), Wiley-Interscience, New York (1991).
Switzer, R. C., et al., Anal. Biochem. 98, 231–237 (1979).
Wilson, C. M., Methods Enzymol. 91, 236–247 (1983).
t m 80-6013-88 • p66
• glossary
Glossary
ammonium persulphate The initiator of acrylamide polymerization. Used
with TEMED to prepare polyacrylamide gels.
ampholyte The general term for amphoteric compounds (i.e. compounds

having both acidic and basic groups, H+ donor and acceptors, respec-
tively) used in isoelectric focusing. Ampholytes form a pH gradient by
migrating during electrophoresis to their isoelectric point in the gel. The
exact isoelectric point depends on the number and proportion of acidic
and basic groups and their pK’s. These titratable groups define the pH at
the isoelectric point by their buffering capacity. A variety of pH ranges
are available commercially.
anode The positive (+) electrode. Negatively charged proteins (anions)

move toward the anode. The anode is connected to the power supply
with the red high-voltage lead.
anolyte The electrode solution used in the positive (+) or anodic buffer
chamber in systems where two separate electrode buffers are used, such
as isoelectric focusing. Typically, phosphoric or acetic acid is used.
antigen A compound that, when injected into an animal, causes the

production of antibodies.
cathode The negative (–) electrode. Positively charged proteins (cations)

move toward the cathode. The cathode is connected to the power supply
with the black high-voltage lead.
catholyte The electrode solution used in the negative (–) or cathodic buffer
chamber in systems where two separate electrode buffers are used, such as
isoelectric focusing. Typically sodium hydroxide or histidine is used.
%C – The percentage of cross-linker in the polyacrylamide solution:

g(bisacrylamide)
%C = × 100
The amount of cross-linker (bisacrylamide) varies depending on the appli-

cation. The increased cross-linking gives a stronger gel, an important
consideration for low-percentage acrylamide gels.
CHAPS [3-(3-cholamidoproplyl[dimethylammonio])-1-propanesulphonate]
A zwitterionic detergent with the ability to disrupt nonspecific protein
interactions and preserve the native form of proteins. Used for protein
solubilization during sample preparation for IEF and 2-D electrophoresis.
Coomassie Brilliant Blue R250, R350, and G250 Protein stains used to
visualize proteins after electrophoresis.
discontinuous gel electrophoresis Gel electrophoresis with different stack-

ing and separating buffers to resolve macromolecules such as proteins.
Discontinuous electrophoresis provides superior resolution compared
with continuous (single-buffer) systems.
• p67
protein electrophoresis • glossary
electrophoresis The movement of a charged molecule under the influence

of an electric field.
isoelectric focusing (IEF) Separation of proteins based on their isoelec-

tric point.
molecular weight and molecular mass These two expressions are not
equivalent (Instructions to Authors, Journal of Biological Chemistry),
although they are used interchangeably in electrophoresis. Molecular
weight (Mr or relative molecular mass) is defined as the ratio of a mole-
cule’s mass to that of 1⁄12 the mass of carbon 12 and is thus dimensionless.
Molecular mass, not a ratio, is defined as the mass of one molecule and
is generally expressed in Daltons (Da). One can say that myosin has a
molecular mass of 205 000 Daltons (205 kDa) or a molecular weight
of 205 000 (Mr 205 000). Note that molecular weight is a ratio without
units and should not be expressed in daltons.
Ohm’s law V = IR, where V = voltage (V), I = current (A), and R = resis-
tance (Ohms, Ω). Various forms of the law are used in electrophoresis to
determine the current, voltage, and power to use during a separation.
PAGE (polyacrylamide gel electrophoresis) The most widely used form

of electrophoresis in the vertical format; uses polyacrylamide as the sepa-
ration medium. Typically, it is used for smaller-molecular-weight DNA
and proteins.
SDS (sodium dodecyl sulphate) An anionic detergent used in SDS gel

electrophoresis. SDS binds to proteins at a fixed ratio of 1.4 g SDS per
g of protein.
SDS-PAGE A variation of electrophoresis that uses the anionic detergent

SDS to ensure that all proteins are denatured and carry a negative charge
at a constant charge-to-mass ratio. With excess SDS conditions, protein
mobility in an electrophoretic gel is related primarily to the size, not the
intrinsic charge of the protein.
%T – The percentage of total monomer in a gel:
%T = × 100
100 ml
TEMED The catalyst of acrylamide polymerization. Used with ammonium

persulphate (initiator) to prepare polyacrylamide gels.
Triton X-100 (polyoxyethylene-p-isooctylphenol) A nonionic detergent

commonly used in IEF. Sample concentrations up to 2% can be used.
urea A denaturant used for solubilizing proteins in denaturing IEF at

concentrations of 8 M.
Western blotting (protein blotting) Electrophoretic transfer of elec-

trophoretically separated proteins onto a nitrocellulose, PVDF, or nylon
membrane. The membrane is a close replica of the original gel. The
transferred proteins are readily accessible for probing with antibodies
or other reagents.
t m 80-6013-88 • p68
• index
Index
A
Acrylamide
characteristics of as gel matrix, 6
chemical structure of, fig., 1
drying and storing gels, 61
recommendations for protein separations, 26
Automated gel staining 58, 60
Agarose
characteristics of as gel matrix, 6
chemical structure of, fig., 1
Analysis of gels
documentation, 62
estimation of molecular weight, 62-65
gel drying and storage, 61
staining with Coomassie Blue, 55-58
silver staining, 58-60
troubleshooting, 39, 53, 66
Bovine Erythrocyte Carbonic Anhydrase, IPG analysis of, 51

Buffer systems
continuous, 15
discontinuous, 15
Blotting, see Western transfer blotting
Coomassie Brilliant Blue staining, 55-58
Denaturing IEF, 48-50

Densitometer, 62
Detection of proteins in polyacrylamide gels, 8-11
EEO, see Electroendosmosis

Electroendosmosis (EEO) in gel running, 5
Electrophoresis
apparatus set up for, 1, 2, 13-15
electrical parameters, 2-3
IEF, Chapter 3
preparing protein standards and samples for, 18, 21, 46, 49, 51
problems with
heat, 4-5, 39
polymerization, 8-10, 39
samples for, 40
SDS-PAGE, Chapter 2
theory of,
buffers and pH, 3-4
data analysis, 61-65
electrical parameters, 2-3
gel specifications, 1-2
matrix selection, 5-8
preparation of gels, 6-8
temperature regulation, 4-5
troubleshooting, 39, 53, 66
Equipment choices, 13-14
Estimation of protein molecular weight by SDS-PAGE, 62-65
• p69
protein electrophoresis • index
Flatbed electrophoresis
SDS-PAGE, 36-38
IEF, Chapter 3
Frowning, in SDS-PAGE gels, 39
Gel documentation, 62
Glossary, 67-68
Gradient gels, see Linear gradient gels
H
Horizontal acrylamide gels, 1-2, 36-38, Chapter 3
IEF, see Isoelectric focusing

Immobilized pH gradient (IPG) gels, 43-44, 50-52
IPG gels, see Immobilized pH gradient gels
Isoelectric point
in isoelectric focusing, 10, 43-44
influence on buffer selection in electrophoresis, 4
Isoelectric focusing (IEF)
denaturing
solutions for, 48
materials and equipment for, 48
procedure for running gels, 48-50
immobilized pH gradients (IPG) in
procedure for running and gels, 50-52
reagents and equipment for, 50-51
native
solutions for, 45
materials and equipment for, 46
procedure for running gels, 46-47
theory, 4, 43-44
troubleshooting, 53
L
Laemmli SDS-PAGE system, 16

Linear gradient gels, preparing and running, 30-35
Matrix, selection of, 5-8

Minigels, in SDS-PAGE separations, 23-29
Molecular weight of proteins, calculating with SDS-PAGE, 62-65
Native gel electrophoresis, 36

Native IEF, 45-47
Ohm’s Law, 2
t m 80-6013-88 • p70
• index
Precast acrylamide gels

for multiphor II system, 37, 45
Photochemical polymerization, 7-8
Polyacrylamide gels
drying and storing, 61
monomer preparation for, 6
polymerization of, 7-8
pore size determination in, 7
staining, 55-60
Power equation, 2
Protein
determining molecular weight of, 62-65
isoelectric focusing of, Chapter 3
separation of with SDS-PAGE gels, Chapter 2
staining in SDS-PAGE gels, 55-60
standards for gel separations, 18, 36
Quantitative analysis of data from electrophoresis, 9-10, 62-65
Reagents and solutions, recipes

Acrylamide solution, 16
Ammonium persulfate (10%), 17
Anode Solution
for IEF gels, 45
Cathode Solution
for IEF gels, 45
Coomassie Blue Staining Solution, 56
Denaturing IEF rehydration solution, 48
Destaining
Solution I, 56
Solution II, 56
Developing Solution, 59
Fixing Solution
for Coomassie Blue staining
IEF gels, 56
Tris-tricine gels (small proteins), 56
for silver staining, 59
Glutaraldehyde fixing solution, 56
Gradient Gel Solution, 31-34 (Table)
IEF
anode solution, 45
cathode solution, 45
Preserving Solution, 59
Rehydration solution, 48
Resolving Gel
Buffer (4×), 16
Overlay, 17
Resolving Gel Solution for SDS
minigel, 25 (Table)
standard gel, 20 (Table)
SDS (10%), 17
Sensitizing Solution, 59
Silver Solution, 59
Silver staining fixing solution, 59
Stacking Gel Solution for SDS
minigel, 26 (Table)
standard gel, 20 (Table)
Stacking Gel Buffer (4×), 17
Staining solution, 56
• p71
protein electrophoresis • index
Stop Solution, 59
Tank Buffer, 17
Treatment Buffer (2×), 17
Trichloro acetic acid fixing solution (for IEF gels), 56
Water-saturated n-butanol, 17
Scanners, 62
SDS-PAGE
buffer systems for, 15
calculating protein weights from, 62-65
drying and storing gels from, 61
equipment choices, 13-15
gel documentation, 62
preparing and running
large gels, 19-23
linear gels, 30-34
minigels, 23-29
protein standards for, 18, 63
solutions, reagents, and equipment for, 16-18
staining gels from, 55-60
troubleshooting, 39-40
SDS-polyacrylamide gel electrophoresis; see SDS-PAGE
Silver staining
method, 58-60
reagents for, 59
Smiling, in SDS-PAGE gels, 39
Standards, 18, 63
Submarine gels, 2
Transfer, protein see Western transfer blotting
Vertical slab gels, casting, 2, Chapter 2
Western transfer blotting, 10-11
t m 80-6013-88 • p72
• notes
Notes:
• p73
protein electrophoresis • notes
Notes:
t m 80-6013-88 • p74
• notes
Notes:
• p75
Ampholine, CleanGel, Easy Breeze, ExcelGel, Gel Pool,
Hoefer, ImageMaster, Immobiline, Mighty Small,
Multiphor, MultiTemp, Pharmalyte, PhastSystem,
Plus One, and Spacer-Mate are trademarks of Amer-
sham Pharmacia Biotech Limited or its subsidiaries.
Amersham is a trademark of Nycomed Amersham plc.
Pharmacia and Drop Design are trademarks of

Pharmacia & Upjohn Inc.
Coomassie is a trademark of ICI Americas Inc.
Tris is a trademark of Union Carbide Chemicals

and Plastics Co.
Hamilton is a trademark of Hamilton Company.
© 1999 Amersham Pharmacia Biotech Inc.

All rights reserved.
All goods and services are sold subject to the terms

and conditions of sale of the company within the
Amersham Pharmacia Biotech group that supplies
them. A copy of these terms and conditions is
available on request.
Printed in the USA.
Amersham Pharmacia Biotech UK Limited

Amersham Place Little Chalfont
Buckinghamshire England HP7 9NA
Amersham Pharmacia Biotech AB

SE-751 84 Uppsala Sweden
Amersham Pharmacia Biotech Inc.

800 Centennial Avenue PO Box 1327
Piscataway NJ 08855 USA
Amersham Pharmacia Biotech Europe GmbH

Munzinger Strasse 9 D-79111 Freiburg Germany
www.apbiotech.com

Protein Electrophoresis: Technical Manual

Uploaded by

Document Informationclick to expand document information

Document Informationclick to expand document information

Copyright:

Available Formats

Protein Electrophoresis: Technical Manual

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Protein Electrophoresis: Technical Manual

Uploaded by

Copyright:

Available Formats

tech nical manual

• Work area. The bench and floor should be dry.

• High-voltage connections. The high-voltage leads should be intact and

• Electrophoresis chambers. These should be covered when in use, with

The following power connection protocol should minimize these hazards

• Connect the gel box and leads to power supply.

Caution. When connecting high-voltage leads to the power supply, use

Caution.Power supplies have internal capacitance that stores electrical

• Unplug the high-voltage leads using your right hand only.

Introduction to electrophoretic theory

1.0 Principles of electrophoresis

Electrophoresis of macromolecules is normally carried out by applying a

In most electrophoresis units, the gel is mounted between two buffer

Horizontal acrylamide gels, like vertical slabs, must be polymerized between

1.1 Electrical parameters

Fig 1.4. Diagram of vertical slab gel assembly V = IR or I = V (eq 1)

Power supplies used for electrophoresis hold one electrical parameter

Most of the charge of a protein comes from the pH-dependent ioniza-

For electrophoretic protein separations based on the mobility of the differ-

1.3 Effects of heat on separations

Heat can cause a number of problems during electrophoresis:

• When separating native proteins by electrophoresis, the Joule heat must

• Nonuniform heat distribution distorts band shapes due to different

Recognizing and dealing with these problems is covered more thoroughly

To maintain acceptable temperature control and uniformity throughout

Polyacrylamide, which makes a small-pore gel, is used to separate most

Whichever matrix is selected, it is important that it be electrically

1.4.1 Agarose gels

Agarose is normally purchased as a dry powder. It dissolves when the

The pore size and sieving characteristics of a gel are determined by

1.4.2 Polyacrylamide gels

Because polymerization of acrylamide is a free-radical catalyzed reaction,

Preparing and pouring the monomer solution

Atmospheric oxygen is a free-radical scavenger that can inhibit polymer-

Alternatively, a flat-edged form, such as a comb, can be inserted into the

Determining the pore size

The size of the pores in a polyacrylamide gel is determined by two parame-

Polymerizing the gel

The free-radical vinyl polymerization of acrylamide gel can be initiated

For photochemical polymerization, riboflavin and long-wave UV light

Polymerization of acrylamide generates heat. Rapid polymerization can

1.5 Analysis of the results

The most common analytical procedure is staining. Proteins are usually

Radioactively labelled samples separated on a slab gel are commonly

Qualitative analysis of gels for the presence or absence of a band or

Determining the size of a macromolecule by its mobility also requires

Proteins can be denatured with urea or sodium dodecylsulphate (SDS).

sizes of unknown species can be estimated by visual comparison to the

ble for detection.

The membrane materials used most frequently in blotting are nitrocellu-

Transferring separated molecules electrophoretically is generally faster

1.7 Protocols in this manual

1.8 References and bibliography

Ausubel, F. M., et al., eds. Current Protocols in Molecular Biology,

Hames, B. D., ed., Gel Electrophoresis of Proteins: A Practical Approach

Southern, E. M. Detection of specific sequences among DNA fragments

Polyacrylamide gel electrophoresis