Desmodur LU-D MOCA

DESMODUR® LU-D + MOCA 70 to 95 Shore A
NATURE OF COMPONENTS
Prepolymer nature Nature of chain extender and other components
TDI-Ester MOCA Amine chain extender
CHARACTERISTICS OF COMPONENTS
DESMODUR® DESMODUR® DESMODUR® DESMODUR® DESMODUR®
Unit MOCA
LU-D70 (*) LU-D80 (*) LU-D85 LU-D90 LU-D95
% NCO % 2.3 (± 0.2) 3.2 (± 0.2) 3.6 (± 0.2) 4.15 (± 0.2) 5.2 (± 0.2) -
Physical appearance at room temperature - solid solid solid solid solid solid
Processing temperature °C 80 80 80 80 80 120
Viscosity at processing temperature cps 1200 600 850 750 550 -
Specific gravity at processing temperature - 1.15 1.16 1.18 1.19 1.19 1.25
ELASTOMER TYPICAL PROPERTIES (DATA GIVEN AS AN INDICATION)

Prepolymer
LU-D70 LU-D80 LU-D85 LU-D90 LU-D95
Chain extender MOCA MOCA MOCA MOCA MOCA
Hardness at 20°C DIN 53505 Shore 70 A (**) 80 A 85 A 90 A 95 A
10% Modulus DIN 53504 MPa 1.4 2.3 3.2 4.3 8.8
100% Modulus DIN 53504 MPa 2.9 5.0 6.0 8.0 13.9
200% Modulus DIN 53504 MPa 3.6 6.0 8.0 10.5 17.2
300% Modulus DIN 53504 MPa 5.5 9.0 12.0 14.8 22.9
Tensile strength DIN 53504 MPa 52 53 59 56 50
Elongation DIN 53504 % 660 645 600 600 500
Tear strength : without nick ISO 34-1 kN/m 70 85 95 119 145
Tear strength : with nick ISO 34-1 kN/m 38 45 50 82 86
Resilience DIN 53512 % 50 39 35 31 33
Abrasion loss ISO 4649 mm³ 30 30 30 35 35
Compression set (deflection / 22 h / 70 °C) ISO 815-1 % 30 30 30 32 30
Hardness at -5°C DIN 53505 Shore 80 A 90 A 94 A 95 A 72 D
Hardness at 80°C DIN 53505 Shore 70 A 77 A 84 A 90 A 95 A
Specific gravity 1.24 1.25 1.27 1.26 1.25
(*) specific sales conditions.
(**) depending on process conditions, curing and post curing temperature, hardness may vary from ± 3 Shore A.
Labelling : This system data sheet is only valid in combination with the corresponding components current safety data sheets ! Any updating of safety relevant information – in accordance with EU directives – will only be reflected in the
Safety Data Sheets, copies of which will be revised and distributed. For further technical information relating to safety, the Safety Data Sheets should be consulted.
Covestro Elastomers SAS - 46, avenue des Allobroges - BP 116 - 26103 Romans cedex - France - Tel. 33 (0)4 75 72 72 75 - Fax 33 (0)4 75 02 11 73 - E-mail: info.elastomers@covestro.com – www.elastomers.covestro.com
Covestro Elastomers SAS is certified ISO 9001 : 2008
Version 13
DESMODUR® LU-D + MOCA 70 to 95 Shore A
STORAGE AND USE PRECAUTIONS

Unit MOCA
Optimal storage temperature of the drums °C < 30 < 30 < 30 < 30 < 30 < 30
Storage time (sealed drum) Month 6 6 6 6 6 12
PREPARATION BEFORE PROCESSING
Melting at 110°C
Preheating time / preheating temperature h / °C 48 / 70
minimum before use
Homogenization before processing required - no no no no no no
Degassing required - yes yes yes yes yes no
Keep from heat and protect against moisture.
PROCESSING
Prepolymer
Chain extender MOCA MOCA MOCA MOCA MOCA
Hardness Shore 70 A 80 A 85 A 90 A 95 A
Prepolymer processing temperature °C 80
MOCA processing temperature °C 120
Parts by weight of prepolymer 100 100 100 100 100
Parts by weight of MOCA 6.9 9.7 10.9 12.5 15.7
MOLDING AND CURING
Mold temperature °C 100
Pot life (400g mixture) min 13’ 9’ 7’30’’ 5’30’’ 3’30’’
Demolding time min 80’ 30’ 30’ 20’ 15’
Post-curing hr / °C 16 / 100
Use of degassing agent is recommended for hand casting.

A one week aging at room temperature is required to obtain the optimal properties of the elastomer.
The following information and our technical advice – whether verbal, in writing or by way of trials – are given in good faith but without warranty, and this also applies where proprietary rights of third parties are involved. Our advice
does not release you from the obligation to check its validity and to test our products as to their suitability for the intended processes and uses. The application, use and processing of our products and the products manufactured by
you on the basis of our technical advice are beyond our control and, therefore, entirely your own responsibility. Our advice concerning safety does not release you from the obligation to determine the safety measures designed for
your production environment, that we may not be able to anticipate, to check abilities and to inform the people who will use, handle or be in contact with these products.
Covestro Elastomers SAS - 46, avenue des Allobroges - BP 116 - 26103 Romans cedex - France - Tel. 33 (0)4 75 72 72 75 - Fax 33 (0)4 75 02 11 73 - E-mail: info.elastomers@covestro.com – www.elastomers.covestro.com
Covestro Elastomers SAS is certified ISO 9001 : 2008
Version 13

Desmodur LU-D MOCA

Uploaded by

Copyright:

Available Formats

Desmodur LU-D MOCA

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Desmodur LU-D MOCA

Uploaded by

Copyright:

Available Formats

DESMODUR® LU-D + MOCA 70 to 95 Shore A

ELASTOMER TYPICAL PROPERTIES (DATA GIVEN AS AN INDICATION)

STORAGE AND USE PRECAUTIONS

Degassing required - yes yes yes yes yes no

Keep from heat and protect against moisture.

Use of degassing agent is recommended for hand casting.

You might also like