HP2100TECH

Technical Instructions Printers OEM Info Tools 1

CANON PC-1060/1080f Part Number: C4096A Phillips Screwdriver
CORPORATE HP2100 Gram Load: 230 gms Small Flat Blade Screwdriver
LOS ANGELES, USA Yield @ 5%: 5,000 pgs
HP2100TN Needlenose Pliers
US 1 800 394.9900 Pages/Min.: 10
Int’l +1 818 837.8100 HP2100M (Mac) Soft Lint-Free Cloth
FAX 1 800 394.9910 Resolution: 1200dpi Cotton Swabs
Int’l +1 818 838.7047 OEM Cart: $89.00 Anhydrous Isopropyl Alcohol
ATLANTA, USA
US 1 877 676.4223
Int’l +1 770 516.9488 The HP2100 has a lot of similarities to the HP4000, and a few parts are
FAX 1 877 337.7976 interchangeable. It is based on the same development, toner and drum
Int’l +1 770 516.7794
technology but the engines are different and should be treated as totally
DALLAS, USA separate cartridges.
US 1 877 499.4989
Int’l +1 972 840.4989
FAX 1 877 774.1750 Photo 1
Int’l +1 972 840.1750
Step 1
MIAMI, USA
US 1 800 595.429 Place the cartridge top down, drum side
Int’l +1 305 594.3396 up, on the table with the plastic drum side
FAX 1 800 522.8640
Int’l +1 305 594.3309 plate facing you. With a #1 Phillips screw-
driver, remove two screws. Pull the plastic
NEW YORK, USA
US 1 800 431.7884
drum side plate away.
Int’l +1 631 345.0121 (See Photo 1)
FAX 1 800 431.8812
Int’l +1 631345.0690

SANFORD,USA
US 1 800 786.9049
Int’l +1 919 775.4584
FAX 1 800 786.9049 Photo 2
Int’l +1 919 775.4584 Step 2
TORONTO, CAN Rotate the cartridge and remove the
CAN 1 877 848.0818 drum axle pin from the small gear end
Int’l +1 905 712.9501
FAX 1 877 772.6773 using needlenose pliers.
Int’l +1 905 712.9502
(See Photo 2)
BUENOS AIRES, ARG
ARG 0810 444.2656
Int’l +011 4583.5900
FAX +011 4584.3100

MELBOURNE, AUS
AUS 1 800 003. 100
Int’l +62 03 9561.8102
FAX 1 800 004.302
Int’l +62 03 9561-7751
Step 3 Gray 5%
SYDNEY, AUS
Place the axle pin aside. Pull the drum bend or tear the blade, causing future
AUS 1 800 003.100
Int’l +62 02 9648.2630 shutter back and tape it or hold it with toner leaks. If you plan to use the drum
FAX 1800 004.302 your thumb and grab the drum by the again, wrap it in paper and place it to the
Int’l +62 02 9548.2635
small gear end. side.
MONTEVIDEO,URY
URY 02 902.7206
Lift and pull the drum out, being careful
Int’l +5982 900.8358 not to catch the large drum gear on the
FAX +5982 908.3816 corner of the recovery blade, it may
JOHANNESBURG, S.A.
S.A. +27 11 974.6155
FAX +27 11 974.3593

E-mail: info@futuregraphicsllc.com Website: www.futuregraphicsllc.com

2 HP2100 Technical Instructions

Photo 4
Step 5
You can now remove the two pins that
hold the cartridge together. These are
Step 4
tapered pins pushed in from the outside,
Next, using a pair of needlenose so they must be removed from the inside
pliers, grasp the PCR by the metal of the cartridge. With the drum shutter
shaft, remove it, and place it off to held back, use a long punch or thin flat
the side as well. (See Photo 3) blade screw driver, press the tapered pins
out as far as possible, from the inside on
both ends of the cartridge.
(See Photo 4)
Photo 3 Photo 5

Grasp the pins from the outside and

remove.
(See Photo 5)

Step 6 Step 7 Step 8

Set the toner hopper aside for Lift the wiper blade out and away. Dump Clean or replace the wiper blade and rein-
now. Hold the waste hopper out all waste toner from the hopper, stall it at this time. Clean the PCR with a soft
with the wiper blade facing you, being careful not to damage the recov- clean cloth (do not use water or solvents on
and remove the two Phillips ery blade or foam seal (on the upper this PCR, it reacts differently than those of
head screws holding the wiper back of the waste hopper). Clean the previous PCR technology). Reinstall the PCR,
blade. (See Photo 6) PCR saddles with a cotton swab and place the drum in position and reinstall the
alcohol. axle pin and the plastic side plate. The waste
hopper is now finished and can be set aside.

Photo 6 Photo 7
Step 9
Take the toner hopper and place it on the table
with the mag roller side facing you. The drum
cover is easily broken and attached on the left
side by a wire only. On the right side it is
attached by both a wire and the curved,spring-
loaded plastic “drum cover arm”. To remover it,
lift the drum cover spring arm and latch it on
the cutout of the arm. (See Photo 8)

Photo 8
Step 10
Next, take a flat blade screwdriver and pry
the drum arm outward until it comes
completely off the shaft.
(See Photo 8)

Need trust-worthy, detailed Technical

Instructions for another engine?
Visit: www.futuregraphicsllc.com
 HP2100 Technical Instructions 3

Photo 9
Step 11
At this point, pull the wire and arm out on
this side until it is completely released Notes
from the toner hopper.
(See Photo 9)

Step 12
Turn the wire back and upward until the
keyed flat piece of the wire on the other
Photo 10 side is vertical and aligned with the vertical
slot on the plastic side plate, then slide it
out. Do NOT force it, as it will come out
easily when aligned correctly.
(See Photo 10)
You have now completely removed the
drum cover (it is very easy to re-install in
reverse order). Set it aside until the end.

Photo 11 Step 13
Next, use a Phillips screwdriver to remove
the two screws on the left (gear) side of
the toner hopper (See Photo 11)
Step 14
Pressing backward on the latch with a
small, flat blade screwdriver remover the
side plate. All the gears will stay attached to
the side cover and can easily be air cleaned.

Photo 12
Step 15
Rotate the cartridge and remove the two
screws on the other end.
(See Photo 12)

Photo 13

Press backward on the latch with a small,

flat blade screwdriver and remove the side
plate.
(See Photo 13)
Need help with a particular remanu-
facturing problem?
Call the Technical Resource Center from
8am - 5pm PST: 800 394.9900
 4 HP2100 Technical Instructions

Photo 15
Step 17
The mag roller can now be removed.
(See Photo 15)
Step 16
NOTE: Be careful no to lose the small c-
Using a cotton swab and
shaped inner-bearing guide attached to
alcohol, remove all conductive
the stabilizer arm.
grease from the mag roller
contact and replace with fresh
conductive grease. If you
remove the white plastic mag
roller guide, carefully put it Photo 16
back in the correct position. Step 18
NOTE: This mag roller guide will Remove the two Phillips head screws hold-
cause binding if put back on ing on the doctor blade.
wrong.
(See Photo 16)
(See Photo 14)
NOTE: Be careful not to lose the two clear
mylar shims behind the doctor blade.

clear mylar shims

Photo 14 Photo 17
Step 19
Dump the remaining toner from the toner
hopper and vacuum or clean with com-
pressed air. Clean the toner sensor bar with
a cotton swab and alcohol. (See Photo 17)
Step 20
Use a vacuum or compressed air to clean
the mag roller “magnetic seals”.

Step 21 Step 23 Step 24

The hopper may now be filled through the After splitting the hopper and installing Complete re-assembling the toner hop-
magnetic roller opening and reassembled a gasket seal, add the toner through the per, including reinstallation of the drum
in reverse order, if a seal is not to be used. fill plug hole and re-install the plug. cover assembly. Check for toner leak-
Use rail clips or hopper clips to reattach age.
Step 22
both pieces of the hopper back Step 25
If you plan to split and seal the hopper, together, being careful to align them
it must be done so with a splitting properly. With the toner hopper and waste hop-
machine or “dremel” tool along the per units now re-assembled, test each
toner hopper weld as shown by the one for free movement and lack of
arrows in photo 18. (See Photo 18) noise by turning them manually.

Photo 18 Photo 19
Step 26
Finally, join the two hoppers together.
Align them and push the two pins into
place.
(See Photo 19)
The cartridge is now ready for testing.

Future Graphics (FG) is a distributor of compatible replacement parts and products for imagining equipment.
None of FG's products are genuine OEM replacement parts and no affiliation or sponsorship is to be implied between FG and any OEM.