R300LC 9S

SAFETY HINTS
1. BEFORE OPERATING THE MACHINE
Think-safety first.
In special situation, wear protective clothing
including a safety helmet, safety shoes, gloves,
safety glasses and ear protection as required by
the job condition.
Almost every accident is caused by disre-
garding the simple and fundamental safety
hints.
13031SH01
Be sure to understand thoroughly all about the

operator's manual before operating the
machine.
Proper care is your responsibility.
13031SH02
Fully understand the details and process of the

construction before starting the work.
If you find anything dangerous on the job,
consult with the job supervisor for the pre-
ventive measures before operating the machine.
13031SH03
Do not operate when tired, or after drinking

alcoholic beverages or any type of drugs.
13031SH05
1-1
Check daily according to the operation man-
ual.
Repair the damaged parts and tighten the loos-
ened bolts.
13031SH05
Check for leakage of engine oil, hydraulic oil,

fuel and coolant.
Keep machine clean, clean machine regularly.
13031SH06
Do not operate the machine if it requires repairs.

Operate after complete repair.
13031SH07
Be prepared if a fire starts.

Keep a fire extinguisher handy and emergency
numbers for a fire department near your tele-
phone.
13031SH08
1-2
PROTECTION AGAINST FALLING OR
FLYING OBJECTS Top guard
If there is any danger of falling or flying objects
hitting the operator, install protective guards in
place to protect the operator as required for
each particular situation.
Be sure to close the front window before com-
mencing work.
Make sure to keep all persons other than opera-
tor outside the range of falling or flying objects.
In case you need top guard, front guard and
FOPS (falling object protective structure),
please contact Hyundai distributor in Europe. Front guard
21091SH01
UNAUTHORIZED MODIFICATION
Any modification made without authorization

from Hyundai can create hazards.
Before making a modification, consult your
Hyundai distributor. Hyundai will not be respon-
sible for any injury or damage caused by any
unauthorized modification.
PREPARE FOR EMERGENCY
Only in case of emergency, use the installed

hammer for breaking the windshield of the cab,
and then exit carefully.
Be sure you know the phone numbers of per-
sons you should contact in case of an emergen-
cy.
Hammer
21091SH02
1-3
ROTATING BEACON
Beacon
When you operate a machine on a road or
beside a road, a rotating beacon is required to
avoid any traffic accident.
Please contact your Hyundai distributor to install
it.
21091SH03
PRECAUTIONS FOR ATTACHMENTS

When installing and using an optional attach-
ment, read the instruction manual for the attach-
ment and the information related to attachments
in this manual.
Do not use attachments that are not authorized
by Hyundai or your Hyundai distributor. Use of
unauthorized attachments could create a safety
problem and adversely affect the proper opera-
tion and useful life of the machine.
Any injuries, accidents, product failures resulting
from the use of unauthorized attachments are
not the responsibility of Hyundai.
The stability of this machine is enough to be
used for general work. When you operate this
machine, allow for the lifting capacity tables. If
you want to use other special applications (not
covered in this manual), you have to attach
additional counterweight or be cautious while
running the machine.
SAFETY RULES
Only trained and authorized personnel can
operate and maintain the machine.
Follow all safety rules, precautions and instruc-
tions when operating or performing mainte-
nance on the machine.
When working with another operator or a per-
son on worksite traffic duty, be sure all person-
nel understand all hand signals that are to be
used.
1-4
SAFETY FEATURES
Be sure all guards and covers are in their prop-
er position. Have guards and covers repaired if
damaged.
Use safety features such as safety lock and
seat belts properly.
Never remove any safety features. Always
keep them in good operating condition.
Improper use of safety features could result in
serious bodily injury or death.
MACHINE CONTROL PATTERN

Check machine control pattern for conformance
to pattern on label in cab.
If not, change label to match pattern before
operating machine.
Failure to do so could result in injury.
CALIFORNIA PROPOSITION 65
Diesel engine exhaust and some of its constitu-
ents are known to the State of California to
cause cancer, birth defects and other reproduc-
tive harm.
This product contains or emits chemicals known
to the State of California to cause cancer or
birth defects or other reproductive harm.
Battery posts, terminals and related accesso-

ries contain lead and lead compounds.
WASH HANDS AFTER HANDLING
WASH HANDS
AFTER HANDLING !
: Battery posts, terminals and related accessories
contain lead and lead compounds,chemicals known to the
State of California to cause cancer and reproductive harm.
13031SH55
Do not load the machine with the lifting eyes on

the counterweight.
The wrong loading method can result in seri-
ous bodily injury or death.
1-5
2. DURING OPERATING THE MACHINE
Use the handle and footstep when getting on or

off the machine.
Do not jump on or off the machine.
13031SH09
Sound the horn to warn nearby personnel

before operating the machine.
Remove all the obstacles like frost on the win-
dow before operating the machine for the good
visibility.
13031SH10
Operate carefully to make sure all personnel or

obstacles are clear within the working range of
the machine.
Place safety guards if necessary.
13031SH11
When using the work equipment, pay attention

to job site.
13031SH12
1-6
Provide proper ventilation when operating
engine in a closed area to avoid the danger of
exhaust gases.
13031SH13
Check the locations of underground gas

pipes or water line and secure the safety before
operation.
13031SH14
The operating near the electrical lines is very

dangerous.
Operate within safe working range permitted as
below.
Supply voltage Min safe separation
6.6 kV 3m (10 ft)

33.0 kV 4m (13 ft)
66.0 kV 5m (16 ft)
13031SH15
154.0 kV 8m (26 ft)
275.0 kV 10m (33 ft)
If the machine touches the electric power lines,

keep sitting on the operator's seat and make
sure the personnel on the ground not to touch
the machine until turning off the electric cur-
rent. Jump off the machine without contacting
the machine when you need to get off.
13031SH16
1-7
Watch out for obstacles.
Be particularly careful to check the machine
clearance during the swing.
13031SH17
When using the machine as breaker or

working in a place where stones may fall down,
cab roof guard and head guard should be pro-
vided for proper protection.
13031SH18
Avoid operating on a cliff or soft ground as there

is danger of rolling over.
Make sure to get off easily as keeping the track
at a right angle and putting the travel motor into
the backward position when working on a cliff or
soft ground inevitably.
13031SH19
Operate for the lifting work considering the

capacity of machine, weight and width of the
load.
Be careful not to lift exceeding the machine
capacity as it can be the cause of machine
damage and safety accident.
13031SH20
1-8
The operation on a slope is dangerous.
Avoid operating the machine on a slope of over
10 degree.
13031SH21
Operate the machine after making ground flat

when operation is required on a slope.
13031SH22
The swing on the slope can be danger of

rolling over.
Do not operate to swing the machine with the
bucket loaded on a slope since the machine
may lose its balance under such an instance.
13031SH23
Avoid parking and stopping on a slope.

Lower the bucket to the ground and block the
track when parking.
13031SH24
1-9
Avoid traveling in a cross direction on a slope as
it can cause the danger of rolling over and slid-
ing.
13031SH25
Traveling on a slope is dangerous.

Be sure to operate slowly when traveling down
a slope and maintain the bucket at a height of
20~30 cm (1 ft) above the ground so that it can
be used as brake in an emergency.
20~30 cm 13031SH26
Steering of the machine while traveling on a

slope is dangerous.
When an inevitable turning of direction is
required, turn on the flat and solid ground.
13031SH27
The engine angularity limits are 35 degree.

Do not operate by more than the engine limits
in any case.
35Á
13031SH28
1-10
Before traveling the machine, sound the horn
to warn nearby personnel.
Operate forward and backward correctly with
confirming the location of the travel motor.
13031SH29
Slow down when traveling through obstacles or

uneven ground.
13031SH30
When working on soft ground, place mats or

wood boards on the ground to prevent the
machine sinking.
13031SH31
When operating in water or when crossing shal-

low, check the bed soil condition and depth and
flow speed of water, then proceed taking care
that water is not above carrier roller.
13031SH32
1-11
MOUNTING AND DISMOUNTING
Never jump on or off the machine. Never get on or off
a moving machine.
When mounting or dismounting, always face the
machine and use the handrails, machine or track
frame steps, and track shoes. Additional track frame
step can be fitted for wider optional shoe. In this case
please contact your Hyundai distributor.
Do not hold any control levers when getting on or off
the machine.
Ensure safety by always maintaining at least three-
point contact of hands and feet with the handrails,
steps or track shoes.
Always remove any oil or mud from the handrails,
steps and track shoes. If they are damaged, repair
them and tighten any loose bolts.
If grasping the door handrail when mounting or dis-
mounting or moving on the track, open and lock the
door securely in the open position. Otherwise, the
door may move suddenly, causing you to lose balance
and fall.
29071FW05/06
KEEP RIDERS OFF MACHINE

Riders on a machine are subject to injury such as
being struck objects and being thrown off the
machine.
Only allow the operator on the machine. Keep riders
off.
1-12
3. DURING MAINTENANCE
Stop the engine immediately when the trouble

of the machine is found.
Inspect immediately the cause of trouble such
as vibration, overheating and trouble in the clus-
ter then repair.
13031SH33
Park on a flat place and stop the engine for

inspecting and repairing. Properly TAG
machine is not operational. (remove start key)
Extreme care shall be taken during mainte-
nance work. Parts may require additional safe
guard.
ON THE
INSPECTION
13031SH34
Do not remove the radiator cap from hot engine.

Open the cap after the engine cools, below 50
°C (122 °F) to prevent personal injury from heat-
ed coolant spray or steam.
13031SH35
Do not work below the machine.

Be sure to work with proper safety supports.
Do not depend on the hydraulic cylinders to
hold up the equipment and attachment.
13031SH36
1-13
There is the danger of fire in fuel and oil.
Store in cool and dry area, away from any open
flames.
13031SH37
Do not touch exhaust pipe, or may cause

severe burn.
13031SH38
Do not open the engine hood and covers while

the engine is running.
13031SH39
Be careful of not hitting the edges when you

service engine.
13031SH40
1-14
Be careful that the front window may be prompt-
ly closed.
Be sure to support stay, when the side door
needs to be opened.
Be careful that the open side door may closed
by the external or natural force like strong wind.
13031SH41
The antislip protection should be replaced if

they have become worn or have been printed
over.
Be sure to free of oil, water and grease etc.
13031SH42
Be careful of not touching slip, fall down etc.,

when you work at the upper frame to service
engine and/or other component.
13031SH43
HIGH PRESSURE GAS

Contain high pressure gas.
To avoid explosion and personal injury, do not
expose to fire, do not weld, do not drill.
Relieve pressure before discharging. 21091SH08
LIFT EYES CAN FAIL

Lift eyes or tank can fail when lifting tank con-
taining fluids resulting in possible personal injury.
Drain tank of all fluids before lifting.
1-15
4. PARKING
When leaving the machine after parking,

lower the bucket to the ground completely and
put the safety lever at parking position then
remove the key.
Lock the cab door.
13031SH44
Park the machine in the flat and safe place.
13031SH45
Hope you can work easily and safely

observing safety rules.
For safe operation, observe all safety rules.
13031SH46
1-16
SPECIFICATIONS
1. MAJOR COMPONENT
Battery box Fuel tank Hydraulic tank Main pump
Engine
Oil cooler
Tooth Bucket Turning joint Swing motor Main control valve Radiator
Arm Arm cylinder Boom Boom cylinder Cab Muffler Counterweight
Bucket cylinder Connecting link Idler Carrier roller Sprocket
Side cutter Connecting rod Track roller Track Travel motor
3309S2SP01
2-1
2. SPECIFICATIONS
1) R330LC-9S
·6.45
6.45 m (21' 2") BOOM and 3.20 m (10' 6") ARM
I(I') D
C
E
G
F
H
J M
K N
A B(L)
3309S2SP02
Description Unit Specification

Operating weight kg (lb) 32700 (72090)
Bucket capacity (SAE heaped), standard m (yd )
3 3 1.44 (1.88)
Overall length A 10980 (36' 0")
Overall width, with 600 mm shoe B 3280 (10' 9")
Overall height C 3380 (11' 1")
Superstructure width D 2980 ( 9' 9")
Overall height of cab E 3090 (10' 2")
Ground clearance of counterweight F 1200 ( 3' 11")
Engine cover height G 2580 ( 8' 6")
Minimum ground clearance H mm (ft-in) 500 ( 1' 8")
Rear-end distance I 3265 (10' 9")
Rear-end swing radius I' 3330 (10' 11")
Distance between tumblers J 4030 (13' 3")
Undercarriage length K 4940 (16' 2")
Undercarriage width L 3280 (10' 9")
Track gauge M 2680 ( 8' 10")
Track shoe width, standard N 600 (24")
Travel speed (low/high) km/hr (mph) 3.3/5.8 (2.1/3.6)
Swing speed rpm 9.5
Gradeability Degree (%) 35 (70)
Ground pressure (600 mm shoe) kgf/cm2(psi) 0.63 (8.96)
Max traction force kg (lb) 29500 (65040)
2-2
2) R330NLC-9S
·6.45
6.45 m (21' 2") BOOM and 3.20 m (10' 6") ARM
I(I') D
C
E
G
F
H
J M
K N
A B(L)
3309S2SP03

Bucket capacity (SAE heaped), standard m3 (yd3) 1.44 (1.88)
Overall width, with 600 mm shoe B 2990 ( 9' 10")
Undercarriage width L 2990 ( 9' 10")
Track gauge M 2390 ( 7' 10")
Swing speed rpm 9.5
2-3
3) R330LC-9S HIGH WALKER
·6.45
6.45 m (21' 2") BOOM and 3.20 m (10' 6") ARM
I(I') D
E
C
G
F
H
J M
K N
A B(L)
3309S2SP04

Bucket capacity (SAE heaped), standard m3 (yd3) 1.44 (1.88)
Overall width, with 600 mm shoe B 3470 (11' 5")
Undercarriage width L 3470 (11' 5")
Track gauge M 2870 ( 9' 5")
Swing speed rpm 9.5
2-4
3. WORKING RANGE
1) R330LC-9S, R330NLC-9S
A
A'
F
D
B' E
C
B
8ft
32092SP05
6.45 m (21' 2") Boom 6.15 m (20' 2") Boom

Description
2.2 m (7' 3") Arm 2.5 m (8' 2") Arm 3.2 m (10' 6") Arm 4.05 m (13' 3") Arm 2.2 m (7' 3") Arm
Max digging reach A 10330 mm (33'11") 10550 mm (34' 7") 11140 mm (36' 7") 11950 mm (39' 2") 10020 mm (32'10")
Max digging reach on ground A' 10110 mm (33' 2") 10330 mm (33'11") 10940 mm (35'11") 11760 mm (38' 7") 9800 mm (32' 2")
Max digging depth B 6370 mm (20'11") 6670 mm (21'11") 7370 mm (24' 2") 8220 mm (27' 0") 6160 mm (20' 3")
Max digging depth (8ft level) B' 6160 mm (20' 3") 6470 mm (21' 3") 7210 mm (23' 8") 8080 mm (26' 6") 5950 mm (19' 6")
Max vertical wall digging depth C 5980 mm (19' 7") 5920 mm (19' 5") 6360 mm (20'10") 7260 mm (23'10") 5710 mm (18' 9")
Max digging height D 10220 mm (33' 6") 10170 mm (33' 4") 10310 mm (33'10") 10710 mm (35' 2") 9940 mm (32' 7")
Max dumping height E 7050 mm (23' 2") 7050 mm (23' 2") 7240 mm (23' 9") 7630 mm (25' 0") 6780 mm (22' 3")
Min swing radius F 4700 mm (15' 5") 4500 mm (14' 9") 4470 mm (14' 8") 4470 mm (14' 8") 4520 mm (14'10")
189.3 [205.5] kN 189.3 [205.5] kN 189.3 [205.5] kN 189.3 [205.5] kN 189.3 [205.5] kN
SAE 19300 [20950] kgf 19300 [20950] kgf 19300 [20950] kgf 19300 [20950] kgf 19300 [20950] kgf
42550 [46200] lbf 42550 [46200] lbf 42550 [46200] lbf 42550 [46200] lbf 42550 [46200] lbf
Bucket digging force
211.8 [230.0] kN 211.8 [230.0] kN 211.8 [230.0] kN 211.8 [230.0] kN 211.8 [230.0] kN
ISO 21600 [23450] kgf 21600 [23450] kgf 21600 [23450] kgf 21600 [23450] kgf 21600 [23450] kgf
196.6 [213.4] kN 178.9 [194.2] kN 143.2 [155.5] kN 119.6 [129.9] kN 196.6 [213.4] kN
Arm crowd force
202.8 [220.2] kN 185.1 [201.0] kN 147.1 [159.7] kN 122.7 [133.3] kN 202.8 [220.2] kN
[ ] : Power boost
2-5
A
A'
F
D
B' E
C
B
8ft
32092SP06
6.45 m (21' 2") Boom 6.15 m (20' 2") Boom

Description
2.2 m (7' 3") Arm 2.5 m (8' 2") Arm 3.2 m (10' 6") Arm 4.05 m (13' 3") Arm 2.2 m (7' 3") Arm
Max digging reach A 10330 mm (33'11") 10550 mm (34' 7") 11140 mm (36' 7") 11950 mm (39' 2") 10020 mm (32'10")
Max digging reach on ground A' 10040 mm (32'11") 10270 mm (33' 8") 10880 mm (35' 8") 11710 mm (38' 5") 9730 mm (31'11")
Max digging depth B 6100 mm (20' 0") 6400 mm (21' 0") 7100 mm (23' 4") 7950 mm (26' 1") 5880 mm (19' 3")
Max digging depth (8ft level) B' 5890 mm (19' 4") 6200 mm (20' 4") 6940 mm (22' 9") 7800 mm (25' 7") 5680 mm (18' 8")
Max vertical wall digging depth C 5700 mm (18' 8") 5650 mm (18' 6") 6080 mm (19'11") 6980 mm (22'11") 5440 mm (17'10")
Max digging height D 10500 mm (34' 5") 10450 mm (34' 3") 10590 mm (34' 9") 10990 mm (36' 1") 10220 mm (33' 6")
Max dumping height E 7330 mm (24' 1") 7330 mm (24' 1") 7520 mm (24' 8") 7910 mm (25'11") 7060 mm (23' 2")
Min swing radius F 4700 mm (15' 5") 4500 mm (14' 9") 4470 mm (14' 8") 4470 mm (14' 8") 4520 mm (14'10")
189.3 [205.5] kN 189.3 [205.5] kN 189.3 [205.5] kN 189.3 [205.5] kN 189.3 [205.5] kN
Bucket digging force
211.8 [230.0] kN 211.8 [230.0] kN 211.8 [230.0] kN 211.8 [230.0] kN 211.8 [230.0] kN
196.6 [213.4] kN 178.9 [194.2] kN 143.2 [155.5] kN 119.6 [129.9] kN 196.6 [213.4] kN
Arm crowd force
202.8 [220.2] kN 185.1 [201.0] kN 147.1 [159.7] kN 122.7 [133.3] kN 202.8 [220.2] kN
[ ] : Power boost
2-6
4. WEIGHT
1) R330LC-9S, R330NLC-9S
R330LC-9S R330NLC-9S
Item
kg lb kg lb
Upperstructure assembly 14390 31720 ą ą
Main frame weld assembly 3760 8290 ą ą
Engine assembly 620 1370 ą ą
Main pump assembly 200 440 ą ą
Main control valve assembly 220 490 ą ą
Swing motor assembly 370 820 ą ą
Hydraulic oil tank assembly 230 490 ą ą
Fuel tank assembly 210 450 ą ą
Counterweight 6200 13670 ą ą
Cab assembly 490 1080 ą ą
Radiator total assy 280 620 ą ą
Lower chassis assembly 11500 25770 11360 25040
Track frame weld assembly 3970 8750 3835 8450
Swing bearing 410 900 ą ą
Travel motor assembly 360 800 ą ą
Turning joint 50 110 ą ą
Tension cylinder 210 450 ą ą
Idler 250 540 ą ą
Sprocket 80 170 ą ą
Carrier roller 40 80 ą ą
Track roller 60 120 ą ą
Track-chain assembly (600 mm standard triple grouser shoe) 1860 4100 ą ą
Front attachment assembly (6.45 m boom, 3.2 m arm,
6390 14090 ą ą
1.44 m3 SAE heaped bucket)
6.45 m boom assembly 2540 5600 ą ą
3.2 m arm assembly 1160 2560 ą ą
1.44 m SAE heaped bucket
3 1120 2470 ą ą
Boom cylinder assembly 300 660 ą ą
Arm cylinder assembly 380 840 ą ą
Bucket cylinder assembly 270 570 ą ą
Bucket control linkage assembly 370 820 ą ą
2-7
Item kg lb
Upperstructure assembly 14790 32600

Main frame weld assembly 3760 8290
Engine assembly 620 1370
Main pump assembly 200 440
Main control valve assembly 220 490
Swing motor assembly 370 820
Hydraulic oil tank assembly 230 490
Fuel tank assembly 210 450
Counterweight 6600 14550
Cab assembly 490 1080
Radiator total assy 280 620
Lower chassis assembly 14000 30860
Track frame weld assembly 6180 13620
Swing bearing 410 900
Travel motor assembly 360 800
Turning joint 50 110
Tension cylinder 210 450
Idler 250 540
Sprocket 80 170
Carrier roller 40 80
Track roller 60 120
Track-chain assembly (600 mm standard triple grouser shoe) 1860 4100
Front attachment assembly (6.45 m boom, 3.2 m arm,
6390 14090
1.44 m3 SAE heaped bucket)
6.45 m boom assembly 2540 5600
3.2 m arm assembly 1160 2560
1.44 m3SAE heaped bucket 1120 2470
Boom cylinder assembly 300 660
Arm cylinder assembly 380 840
Bucket cylinder assembly 270 570
Bucket control linkage assembly 370 820
2-8
5. LIFTING CAPACITIES
1) R330LC-9S
(1) 6.15 m (20' 2") boom, 2.2 m (7' 3") arm equipped with 1.44 m3 (SAE heaped) bucket and 600 mm
(24") triple grouser shoe.
Â : Rating over-front Â : Rating over-side or 360 degree
Load radius At max. reach

Load point 3.0 m (10.0 ft) 4.5 m (15.0 ft) 6.0m (20.0 ft) 7.5 m (25.0 ft) Capacity Reach
height
m (ft)
7.5 m kg *7480 5800 7.69
(25.0 ft) lb *16490 12790 (25.2)
6.0 m kg *8380 *8380 *8070 5900 7160 4610 8.61
(20.0 ft) lb *18470 *18470 *17790 13010 15790 10160 (28.2)
4.5 m kg *12080 *12080 *9630 8430 *8490 5760 6330 4020 9.16
(15.0 ft) lb *26630 *26630 *21230 18580 *18720 12700 13960 8860 (30.1)
3.0 m kg *15590 12350 *11230 7930 8690 5530 5960 3740 9.39
(10.0 ft) lb *34370 27230 *24760 17480 19160 12190 13140 8250 (30.8)
1.5 m kg *18040 11560 12140 7500 8450 5310 5930 3710 9.35
(5.0 ft) lb *39770 25490 26760 16530 18630 11710 13070 8180 (30.7)
Ground kg *18760 11280 11850 7250 8280 5160 6250 3910 9.02
Line lb *41360 24870 26120 15980 18250 11380 13780 8620 (29.6)
-1.5 m kg *16910 *16910 *18280 11280 11760 7170 8240 5130 7070 4450 8.37
(-5.0 ft) lb *37280 *37280 *40300 24870 25930 15810 18170 11310 15590 9810 (27.5)
-3.0 m kg *22970 *22970 *16680 11470 11870 7270 *8360 5670 7.29
(-10 ft) lb *50640 *50640 *36770 25290 26170 16030 *18430 12500 (23.9)
-4.5 m kg *17920 *17920 *13190 11900
(-15.0 ft) lb *39510 *39510 *29080 26230
Note 1. Lifting capacity are based on SAE J1097 and ISO 10567.
2. Lifting capacity of the ROBEX series does not exceed 75% of tipping load with the machine
on firm, level ground or 87% of full hydraulic capacity.
3. The load point is a hook located on the back of the bucket.
4. *indicates load limited by hydraulic capacity.
2-9
Load
1.5 m (5.0 ft) 3.0 m (10.0 ft) 4.5 m (15.0 ft) 6.0 m (20.0 ft) 7.5 m (25.0 ft) 9.0 m (30.0 ft) Capacity Reach
point
height m (ft)
7.5 m kg *5240 *5240 *5970 4280 9.06
(25.0 ft) lb *11550 *11550 *13160 9440 (29.7)
6.0 m kg *6500 5990 5630 3540 9.84
(20.0 ft) lb *14330 13210 12410 7800 (32.3)
4.5 m kg *8090 *8090 *7190 5740 *5440 4060 5070 3130 10.31
(15.0 ft) lb *17840 *17840 *15850 12650 *11990 8950 11180 6900 (33.8)
3.0 m kg *13400 12410 *9820 7840 *8110 5420 6270 3910 4790 2920 10.52
(10.0 ft) lb *29540 27360 *21650 17280 *17880 11950 13820 8620 10560 6440 (34.5)
1.5 m kg *16400 11330 *11460 7290 8260 5120 6100 3750 4740 2860 10.48
(5.0 ft) lb *36160 24980 *25260 16070 18210 11290 13450 8270 10450 6310 (34.4)
Ground kg *10240 *10240 *17910 10800 11500 6920 8000 4890 5960 3620 4920 2970 10.19
Line lb *22580 *22580 *39480 23810 25350 15260 17640 10780 13140 7980 10850 6550 (33.4)
-1.5 m kg *11380 *11380 *14470 *14470 *18150 10650 11300 6740 7870 4760 5400 3270 9.63
(-5.0 ft) lb *25090 *25090 *31900 *31900 *40010 23480 24910 14860 17350 10490 11900 7210 (31.6)
-3.0 m kg *15350 *15350 *19470 *19470 *17370 10730 11300 6740 7880 4770 6380 3920 8.74
(-10.0 ft) lb *33840 *33840 *42920 *42920 *38290 23660 24910 14860 17370 10520 14070 8640 (28.7)
-4.5 m kg *21820 *21820 *15410 11010 *11230 6920 *7480 5360 7.37
(-15.0 ft) lb *48100 *48100 *33970 24270 *25200 15260 *16490 11820 (24.2)
-6.0 m kg *11340 *11340
(-20.0 ft) lb *25000 *25000
2-10
2) R330NLC-9S

height
m (ft)
7.5 m kg *7480 4910 7.69
(25.0 ft) lb *16490 10820 (25.2)
6.0 m kg *8380 7500 *8070 4970 7120 3860 8.61
(20.0 ft) lb *18470 16530 *17790 10960 15700 8510 (28.2)
4.5 m kg *12080 11320 *9630 7110 *8490 4840 6280 3330 9.16
(15.0 ft) lb *26630 24960 *21230 15670 *18720 10670 13850 7340 (30.1)
3.0 m kg *15590 10200 *11230 6630 8640 4620 5910 3080 9.39
(10.0 ft) lb *34370 22490 *24760 14620 19050 10190 13030 6790 (30.8)
1.5 m kg *18040 9460 12060 6220 8390 4400 5880 3040 9.35
(5.0 ft) lb *39770 20860 26590 13710 18500 9700 12960 6700 (30.7)
Ground kg *18760 9200 11770 5980 8230 4260 6200 3210 9.02
Line lb *41360 20280 25950 13180 18140 9390 13670 7080 (29.6)
-1.5 m kg *16910 *16910 *18280 9190 11680 5910 8190 4220 7030 3670 8.37
(-5.0 ft) lb *37280 *37280 *40300 20260 25750 13030 18060 9300 15500 8090 (27.5)
-3.0 m kg *22970 18930 *16680 9370 11800 6000 *8360 4720 7.29
(-10 ft) lb *50640 41730 *36770 20660 26010 13230 *18430 10410 (23.9)
-4.5 m kg *17920 *17920 *13190 9770
(-15.0 ft) lb *39510 *39510 *29080 21540
2-11
Load
point
height m (ft)
7.5 m kg *5240 5170 *5970 3580 9.06
(25.0 ft) lb *11550 11400 *13160 7890 (29.7)
6.0 m kg *6500 5060 5590 2920 9.84
(20.0 ft) lb *14330 11160 12320 6440 (32.3)
4.5 m kg *8090 7130 *7190 4810 *5440 3360 5030 2540 10.31
(15.0 ft) lb *17840 15720 *15850 10600 *11990 7410 11090 5600 (33.8)
3.0 m kg *13400 10240 *9820 6540 *8110 4510 6230 3210 4760 2350 10.52
(10.0 ft) lb *29540 22580 *21650 14420 *17880 9940 13730 7080 10490 5180 (34.5)
1.5 m kg *16400 9230 *11460 6010 8200 4210 6050 3050 4710 2290 10.48
(5.0 ft) lb *36160 20350 *25260 13250 18080 9280 13340 6720 10380 5050 (34.4)
Ground kg *10240 *10240 *17910 8730 11420 5650 7950 3990 5920 2930 4880 2380 10.19
Line lb *22580 *22580 *39480 19250 25180 12460 17530 8800 13050 6460 10760 5250 (33.4)
-1.5 m kg *11380 *11380 *14470 *14470 *18150 8590 11220 5480 7810 3870 5360 2640 9.63
(-5.0 ft) lb *25090 *25090 *31900 *31900 *40010 18940 24740 12080 17220 8530 11820 5820 (31.6)
-3.0 m kg *15350 *15350 *19470 17640 *17370 8660 11220 5480 7820 3880 6340 3190 8.74
(-10.0 ft) lb *33840 *33840 *42920 38890 *38290 19090 24740 12080 17240 8550 13980 7030 (28.7)
-4.5 m kg *21820 18170 *15410 8930 *11430 5660 *7480 4430 7.37
(-15.0 ft) lb *48100 40060 *33970 19690 *25200 12480 *16490 9770 (24.2)
-6.0 m kg *11340 9470
(-20.0 ft) lb *25000 20880
2-12

height
m (ft)
7.5 m kg *7480 6400 7.90
(25.0 ft) lb *16490 14110 (25.9)
6.0 m kg *8560 *8560 *8100 6850 *7570 5250 8.74
(20.0 ft) lb *18870 *18870 *17860 15100 *16690 11570 (28.7)
4.5 m kg *12730 *12730 *9910 9670 *8620 6680 6870 4670 9.22
(15.0 ft) lb *28060 *28060 *21850 21320 *19000 14730 15150 10300 (30.2)
3.0 m kg *16170 14300 *11520 9170 *9400 6440 6550 4420 9.40
(10.0 ft) lb *35650 31530 *25400 20220 *20720 14200 14440 9740 (30.8)
1.5 m kg *18290 13590 *12850 8760 9250 6230 6590 4440 9.31
(5.0 ft) lb *40320 29960 *28330 19310 20390 13730 14530 9790 (30.5)
Ground kg *18750 13380 12960 8530 9100 6100 7020 4730 8.93
Line lb *41340 29500 28570 18810 20060 13450 15480 10430 (29.3)
-1.5 m kg *18620 *18620 *18070 13410 12910 8490 9090 6090 8060 5450 8.21
(-5.0 ft) lb *41050 *41050 *39840 29560 28460 18720 20040 13430 17770 12020 (26.9)
-3.0 m kg *22250 *22250 *16210 13640 *12030 8630 *8240 7100 7.03
(-10 ft) lb *49050 *49050 *35740 30070 *26520 19030 *18170 15650 (23.1)
-4.5 m kg *12130 *12130
(-15.0 ft) lb *26740 *26740
2-13
Load
point
height m (ft)
7.5 m kg *5730 *5730 *5990 4840 9.24
(25.0 ft) lb *12630 *12630 *13210 10670 (30.3)
6.0 m kg *6600 *6600 6100 4100 9.95
(20.0 ft) lb *14550 *14550 13450 9040 (32.6)
4.5 m kg *8400 *8400 *7350 6650 *5820 4790 5570 3700 10.37
(15.0 ft) lb *18520 *18520 *16200 14660 *12830 10560 12280 8160 (34.0)
3.0 m kg *14050 *14050 *10150 9060 *8290 6320 6920 4620 5330 3500 10.53
(10.0 ft) lb *30970 *30970 *22380 19970 *18280 13930 15260 10190 11750 7720 (34.5)
1.5 m kg *16800 13300 *11720 8530 9070 6020 6750 4460 5320 3480 10.45
(5.0 ft) lb *37040 29320 *25840 18810 20000 13270 14880 9830 11730 7670 (34.3)
Ground kg *10990 *10990 *18040 12850 12640 8180 8840 5810 6630 4350 5570 3650 10.11
Line lb *24230 *24230 *39770 28330 27870 18030 19490 12810 14620 9590 12280 8050 (33.2)
-1.5 m kg *12090 *12090 *15330 *15330 *18080 12750 12480 8040 8730 5700 6170 4060 9.50
(-5.0 ft) lb *26650 *26650 *33800 *33800 *39860 28110 27510 17730 19250 12570 13600 8950 (31.2)
-3.0 m kg *16150 *16150 *20540 *20540 *17110 12870 12510 8070 8770 5740 7390 4910 8.53
(-10.0 ft) lb *35600 *35600 *45280 *45280 *37720 28370 27580 17790 19330 12650 16290 10820 (28.0)
-4.5 m kg *20940 *20940 *14870 13200 *10980 8300 *7390 6870 7.03
(-15.0 ft) lb *46160 *46160 *32780 29100 *24210 18300 *16290 15150 (23.1)
2-14
6. BUCKET SELECTION GUIDE
1) GENERAL BUCKET
0.9 m3 SAE 1.14 m3 SAE 1.44 m3 SAE 1.74 m3 SAE 2.10 m3 SAE
heaped bucket heaped bucket heaped bucket heaped bucket heaped bucket
Recommendation
Capacity Width 6.15 m (20' 2")
6.45 m (21' 2") boom
Weight boom
SAE CECE Without With 2.2 m arm 2.5 m arm 3.2 m arm 4.05 m arm 2.2 m arm
heaped heaped side cutter side cutter (7' 3") (8' 2") (10' 6") (13' 3") (7' 3")
0.9 m3 0.8 m3 950 mm 1070 mm 870 kg

(1.18 yd3) (1.05 yd3) (37.4") (42.1") (1920 lb)
1.14 m3 1.0 m3 1110 mm 1230 mm 980 kg

(1.49 yd3) (1.31 yd3) (43.7") (48.4") (2160 lb)
1.44 m3 1.25 m3 1380 mm 1500 mm 1110 kg

(1.88 yd3) (1.63 yd3) (54.3") (59.1") (2450 lb
1.74 m3 1.5 m3 1620 mm 1740 mm 1230 kg

(2.28 yd3) (1.96 yd3) (63.8") (68.5") (2710 lb)
2.10 m3 1.8 m3 1910 mm 2030 mm 1370 kg

(2.75 yd3) (2.35 yd3) (75.2") (79.9") (3020 lb)
Applicable for materials with density of 2000 kg/m3 (3370 lb/yd3) or less
2-15
2) ROCK AND HEAVY DUTY BUCKET
Ľ1.44 m3 SAE
ľ1.44 m3 SAE
Ľ1.73 m3 SAE
heaped bucket
heaped bucket
Recommendation
Capacity Width 6.15 m (20' 2")
6.45 m (21' 2") boom
Weight boom
SAE CECE Without With 2.2 m arm 2.5 m arm 3.2 m arm 4.05 m arm 2.2 m arm
heaped heaped side cutter side cutter (7' 3") (8' 2") (10' 6") (13' 3") (7' 3")
ľ1.44 m3 1.25 m3 1470 mm 1380 kg

-
(1.88 yd3) (1.63 yd3) (57.9") (3040 lb)
Ľ1.44 m3 1.25 m3 1470 mm 1470 kg

-
(1.88 yd3) (1.63 yd3) (57.9") (3240 lb)
Ľ1.73 m3 1.5 m3 1710 mm 1610 kg

-
(2.26 yd3) (1.96 yd3) (67.3") (3550 lb)
ľ: Heavy duty bucket

Ľ: Rock-Heavy duty bucket
2-16
7. UNDERCARRIAGE
1) TRACKS
X-leg type center frame is integrally welded with reinforced box-section track frames. The design
includes dry tracks, lubricated rollers, idlers, sprockets, hydraulic track adjusters with shock
absorbing springs and assembled track-type tractor shoes with triple grousers.
2) TYPES OF SHOES
Triple grouser
Model Shapes
Shoe width mm (in) 600(24) 700(28) 800(32) 900(36)

Operating weight kg (lb) 32700(72090) 33280(73410) 33640(74300) 34040(75180)
R330LC-9S
Ground pressure kgf/cm2 (psi) 0.63(8.96) 0.55(7.82) 0.48(6.83) 0.44(6.26)
Overall width mm (ft-in) 3280(10' 9") 3380(11' 1") 3480(11' 5") 3580(11' 9")
Shoe width mm (in) 600(24) - - -
Operating weight kg (lb) 32500(71650) - - -
R330NLC-9S
Ground pressure kgf/cm2 (psi) 0.62(8.82) - - -
Overall width mm (ft-in) 2990(9' 10") - - -
Shoe width mm (in) 600(24) 700(28) 800(32) Double Grouser
710(28)
R330LC-9S Operating weight kg (lb) 35200(77600) 35800(78920) 36200(79810) 36680(80690)
HIGH WALKER Ground pressure kgf/cm2 (psi) 0.68(9.67) 0.59(8.39) 0.52(7.39) 0.47(6.68)
Overall width mm (ft-in) 3470(11' 5") 3570(11' 9") 3670(12' 0") 3580(11' 9")
3) NUMBER OF ROLLERS AND SHOES ON EACH SIDE

Item Quantity
Carrier rollers 2EA
Track rollers 9EA
Track shoes 48EA
2-17
4) SELECTION OF TRACK SHOE
Suitable track shoes should be selected according to operating conditions.
Method of selecting shoes
Confirm the category from the list of applications in table 2 2, then use table 1 to select the shoe.
Wide shoes (categories B and C) have limitations on applications. Before using wide shoes,
check the precautions, then investigate and study the operating conditions to confirm if these
shoes are suitable.
Select the narrowest shoe possible to meet the required flotation and ground pressure. Application
of wider shoes than recommendations will cause unexpected problem such as bending of shoes,
crack of link, breakage of pin, loosening of shoe bolts and the other various problems.
öTable
Table 1
Track shoe Specification Category
600 mm triple grouser Standard A
700 mm triple grouser Option B
710 mm double grouser Option B
800 mm triple grouser Option C
900 mm triple grouser Option C
öTable
Table 2
Category Applications Applications
Rocky ground, Â Travel at low speed on rough ground with large obstacles such as
A river beds, boulders or fallen trees
normal soil
Normal soil, Â These shoes cannot be used on rough ground with large obstacles such
soft ground as boulders or fallen trees
B
Â Travel at high speed only on flat ground
Â Travel slowly at low speed if it is impossible to avoid going over obstacles
Extremely soft gound Â Use the shoes only in the conditions that the machine sinks and it is
(swampy ground) impossible to use the shoes of category A or B
Â These shoes cannot be used on rough ground with large obstacles such
C
as boulders or fallen trees
Â Travel at high speed only on flat ground
Â Travel slowly at low speed if it is impossible to avoid going over obstacles
2-18
8. SPECIFICATIONS FOR MAJOR COMPONENTS
1) ENGINE
Item Specification
Model Cummins C8.3-C
Type 4-cycle turbocharged charger air cooled diesel engine
Cooling method Water cooling
Number of cylinders and arrangement 6 cylinders, in-line
Firing order 1-5-3-6-2-4
Combustion chamber type Direct injection type
Cylinder bore×stroke 114×135 mm (4.49"×5.32")
Piston displacement 8300 cc (506 cu in)
Compression ratio 18 : 1
Rated gross horse power (SAE J1995) 263 Hp at 1900 rpm (193 kW at 1750 rpm)
Maximum torque 124.3 kgf·m (899 lbf·ft) at 1300 rpm
Engine oil quantity 25.5ℓ(6.7 U.S. gal)
Dry weight 620 kg (1367 lb)
High idling speed 1950+50 rpm
Low idling speed 850±50 rpm
Rated fuel consumption 155.5 g/Hp·hr at 1750 rpm
Starting motor 24V-7.5 kW
Alternator 24V-70A
Battery 2×12V×160Ah
2) MAIN PUMP
Item Specification
Type Variable displacement tandem axis piston pumps
Capacity 2×148.6 cc/rev
Rated oil flow 2×282ℓ/min (74.5 U.S. gpm / 62.0 U.K. gpm)
Rated speed 1900 rpm
2-19
3) GEAR PUMP
Item Specification
Type Fixed displacement gear pump single stage
Capacity 15cc/rev
Maximum pressure 40 kgf/cm2 (570 psi)
Rated oil flow 28.5˶/min (7.5 U.S. gpm/6.3 U.K. gpm)
4) MAIN CONTROL VALVE

Item Specification
Type 9 spools
Operating method Hydraulic pilot system
Main relief valve pressure 350 kgf/cm2 (4980 psi) [380 kgf/cm2 (5400 psi)]
Overload relief valve pressure 400 kgf/cm2 (5690 psi)
[ ]: Power boost
5) SWING MOTOR
Item Specification
Type Axial piston motor
Capacity 169.4 cc/rev
Relief pressure 300 kgf/cm2 (4270 psi)
Braking system Automatic, spring applied hydraulic released
Braking torque 70 kgfÂm (505 lbfÂft)
Brake release pressure 26 kgf/cm2 (370 psi)
Reduction gear type 2 - stage planetary
6) TRAVEL MOTOR
Item Specification
Type Variable displacement bent-axis axial piston motor
Relief pressure 350 kgf/cm2 (4980 psi)
Capacity (max / min) 154.8/88.5 cc/rev
Reduction gear type 3-stage planetary
Braking system Automatic, spring applied hydraulic released
Brake release pressure 9 kgf/cm2 (128 psi)
Braking torque 40 kgfÂm (290 lbfÂft)
2-20
7) REMOTE CONTROL VALVE
Item Specification
Type Pressure reducing type
Minimum 6.5 kg/cm2 (92 psi)
Operating pressure
Maximum 26 kg/cm2 (370 psi)
Lever 61 mm (2.4 in)
Single operation stroke
Pedal 123 mm (4.84 in)
8) CYLINDER
Item Specification
Bore diaÝRod diaÝStroke ͚150Ý͚105Ý1480 mm
Boom cylinder
Cushion Extend only
Arm cylinder
Cushion Extend and retract
Bucket cylinder
Cushion Extend only
ö Discoloration of cylinder rod can occur when the friction reduction additive of lubrication oil spreads on
the rod surface.
ö Discoloration does not cause any harmful effect on the cylinder performance.
9) SHOE
Item Width Ground pressure Link quantity Overall width
Standard ÷600 mm (24") 0.63 kgf/cm2 (8.96 psi) 48 3280 mm (10' 9")
÷700 mm (28") 0.55 kgf/cm2 (7.82 psi) 48 3380 mm (11' 1")
R330LC-9S
Option ÷800 mm (32") 0.48 kgf/cm2 (6.83 psi) 48 3480 mm (11' 5")
÷900 mm (36") 0.44 kgf/cm2 (6.26 psi) 48 3580 mm (11' 9")
R330NLC-9S Standard ÷600 mm (24") 0.62 kgf/cm2 (8.82 psi) 48 2990 mm ( 9' 10")
Standard ÷600 mm (24") 0.68 kgf/cm2 (9.67 psi) 48 3470 mm (11' 5")
R330LC-9S ÷700 mm (28") 0.59 kgf/cm2 (8.39 psi) 48 3570 mm (11' 9")
H/WALKER Option ÷800 mm (32") 0.52 kgf/cm2 (7.39 psi) 48 3670 mm (12' 0")
ø710 mm (28") 0.47 kgf/cm2 (6.68 psi) 48 3580 mm (11' 9")
÷: Triple grouser
øDouble grouser
2-21
10) BUCKET
Capacity Tooth Width
Item
SAE heaped CECE heaped quantity Without side cutter With side cutter
Standard 1.44 m3 (1.88 yd3) 1.25 m3 (1.63 yd3) 5 1380 mm (54.3") 1500 mm (59.1")
0.9 m3 (1.18 yd3)
0.8 m3 (1.05 yd3) 3 950 mm (37.4") 1070 mm (42.1")
1.14 m3 (1.49 yd3) 1.0 m3 (1.31 yd3) 4 1110 mm (43.7") 1230 mm (48.4")
R330LC-9S 1.74 m3 (2.28 yd3) 1.5 m3 (1.96 yd3) 5 1620 mm (63.8") 1740 mm (68.5")
R330NLC-9S
H/WALKER Option 2.10 m3 (2.75 yd3) 1.8 m3 (2.35 yd3) 5 1910 mm (75.2") 2030 mm (79.9")
ľ1.44 m3 (1.88 yd3) 1.25 m3 (1.63 yd3) 5 1470 mm (57.9") -
◎1.44 m3 (1.88 yd3) 1.25 m3 (1.63 yd3) 5 1470 mm (57.9") -
◎1.73 m3 (2.26 yd3) 1.5 m3 (1.96 yd3) 5 1710 mm (67.3") -
ľ: Heavy duty bucket
◎: Rock-Heavy duty bucket
2-22
9. RECOMMENDED OILS
Use only oils listed below or equivalent.
Do not mix different brand oil.
Ambient temperatureĦC(ĦF)
Capacity
Service point Kind of fluid -20 -10 0 10 20 30 40
˶ (U.S. gal)
(-4) (14) (32) (50) (68) (86) (104)
SAE 30
SAE 10W
Engine oil pan Engine oil 25.5 (6.7)
SAE 10W-30
SAE 15W-40
Swing drive 11.0 (2.9)

Gear oil SAE 85W-140
8.0Ý2
Final drive
(2.1Ý2)
ISO VG 32
Tank:
190 (50)
Hydraulic tank Hydraulic oil ISO VG 46
System:
330 (87)
ISO VG 68
ASTM D975 NO.1

Fuel tank Diesel fuel 500 (132)
ASTM D975 NO.2
NLGI NO.1
Fitting
Grease As required
(Grease nipple) NLGI NO.2
Mixture of
Radiator antifreeze
45 (12.0) Ethylene glycol base permanent type
(Reservoir tank) and water
50 : 50
SAE : Society of Automotive Engineers

API : American Petroleum Institute
ISO : International Organization for Standardization
NLGI : National Lubricating Grease Institute
ASTM : American Society of Testing and Material
2-23
CONTROL DEVICES
1. CAB DEVICES
1) The ergonomically designed console box and suspension type seat provide the operator with com-
fort.
2) ELECTRONIC MONITOR SYSTEM
(1) The centralized electronic monitor system allows the status and conditions of the machine to be
monitored at a glance.
(2) It is equipped with a safety warning system for early detection of machine malfunction.
Aircon & heater switch Air vent

Accel dial switch Speaker
Horn switch Seat
Breaker operation sw Storage box
RH control lever
Radio & USB player
Switch panel
Starting switch
Cluster
Master switch
Electric box assy
MCU
Resistor
Fuse box
One touch decel switch

Travel lever Power max switch
Travel pedal LH control lever
Foot rest Safety
Safetylever
lever
3009SH3CD01
3-1
2. CLUSTER (TYPE 1)
1) STRUCTURE
The cluster consists of LCD and switches as shown below. The LCD is to warn the operator in
case of abnormal machine operation or conditions for the appropriate operation and inspection.
Also, The LCD is to set and display for modes, monitoring and utilities with the switches.
The switches are to set the machine operation modes.
ö The cluster installed on this machine does not entirely guarantee the condition of the
machine. Daily inspection should be performed according to chapter 6, Maintenance.
ö When the cluster provides a warning immediately check the problem, and perform the
required action.
Time display
Warning lamps
(See page 3-4)
Gauge(See page 3-3)

Main menu(See page 3-11)
Engine rpm/Tripmeter
(See page 3-19)
4 Pilot lamps
(See page 3-7)
Switches
(See page 3-9)
21093CD07
öThe warning lamp pops up and/or blinks and the buzzer sounds when the machine has a
problem.
The warning lamp blinks until the problem is cleared. Refer to page 3-4 for details.
3-2
2) GAUGE
(1) Operation screen
Default Option 1 Engine coolant temperature gauge
2 Hydraulic oil temperature gauge
3 3 3 Fuel level gauge
1 2
1 4 RPM / Tripmeter display
2
4 4
21093CD07A
ö Operation screen type can be set by the screen type menu of the display.
Refer to page 3-21 for details.
(2) Engine coolant temperature gauge

Η This gauge indicates the temperature of coolant.
ÂWhite range : 40-105˚C (104-221˚F)
ÂRed range : Above 105˚C (221˚F)
Θ If the indicator is in the red range or lamp blinks in red,
turn OFF the engine and check the engine cooling system.
ö If the gauge indicates the red range or lamp blinks in
21093CD07G
red even though the machine is on the normal condition,
check the electric device as that can be caused by the poor
connection of electricity or sensor.
(3) Hydraulic oil temperature gauge

Η This gauge indicates the temperature of hydraulic oil.
ÂWhite range : 40-105˚C(104-221˚F)
ÂRed range : Above 105˚C(221˚F)
Θ If the indicator is in the red range or lamp blinks is red,
reduce the load on the system. If the gauge stays in the red
range, stop the machine and check the cause of the problem.
21093CD07E ö If the gauge indicates the red range or lamp blinks in
(4) Fuel level gauge

Η This gauge indicates the amount of fuel in the fuel tank.
Θ Fill the fuel when the red range, or lamp blinks in red.
ö If the gauge indicates the red range or lamp blinks in
21093CD07F
(5) RPM / Tripmeter display

Η This displays the engine rpm or the tripmeter.
ö Refer to page 3-19 for details.
21093CD02D
3-3
3) WARNING LAMPS
Battery charging warning lamp Air cleaner warning lamp

Engine oil pressure warning lamp Overload warning lamp
Emergency warning lamp
Fuel level warning lamp

Engine coolant
temperature warning lamp Hydraulic oil temperature
warning lamp
4
3009SH3CD10
ö Each warning lamp on the top of the LCD pops up on the center of LCD and the buzzer sounds
when the each warning is happened. The pop-up warning lamp moves to the original position and
blinks when the select switch is pushed. And the buzzer stops.
Refer to page 3-10 for the select switch.
(1) Engine coolant temperature

ΗEngine coolant temperature warning is indicated two steps.
100˚C over : The lamp blinks and the buzzer sounds.
105˚C over : The lamp pops up on the center of LCD and
the buzzer sounds.
Θ The pop-up lamp moves to the original position and blinks
21093CD08A
when the select switch is pushed. Also, the buzzer stops and
lamp keeps blink.
Ι Check the cooling system when the lamp keeps ON.
(2) Hydraulic oil temperature

ΗHydraulic oil temperature warning is indicated two steps.
100˚C over : The lamp blinks and the buzzer sounds.
105˚C over : The lamp pops up on the center of LCD and
the buzzer sounds.
Θ The pop-up lamp moves to the original position and blinks
when the select switch is pushed. Also, the buzzer stops and
21093CD08C
lamp keeps blink.
Ι Check the hydraulic oil level and hydraulic oil cooling system.
(3) Fuel level

ΗThis warning lamp blinks and the buzzer sounds when the level
of fuel is below 69˶(18.2 U.S. gal).
Θ Fill the fuel immediately when the lamp blinks.
21093CD08B
3-4
(4) Emergency warning lamp
ΗThis lamp pops up and the buzzer sounds when each of the
below warnings is happened.
Engine coolant overheating (over 105˚C)
Hydraulic oil overheating (over 105˚C)
Pump EPPR circuit abnormal or open
21093CD30 Attachment flow EPPR circuit abnormal or open
MCU input voltage abnormal
Accel dial circuit abnormal or open
Cluster communication data error
ö The pop-up warning lamp moves to the original position and
blinks when the select switch is pushed. Also the buzzer stops.
This is same as following warning lamps.
Θ When this warning lamp blinks, machine must be checked and
serviced immediately.
(5) Engine oil pressure warning lamp

Η This lamp blinks when the engine oil pressure is low.
Θ If the lamp blinks, shut OFF the engine immediately. Check oil
level.
21093CD32
(6) Battery charging warning lamp

Η This lamp blinks when the battery charging voltage is low.
Θ Check the battery charging circuit when this lamp blinks.
21093CD34
(7) Air cleaner warning lamp

Η This lamp blinks when the filter of air cleaner is clogged.
Θ Check the filter and clean or replace it.
21093CD35
3-5
(8) Overload warning lamp (opt)
Η When the machine is overload, the overload warning lamp
blinks during the overload switch is ON. (if equipped)
Θ Reduce the machine load.
21093CD36
3-6
4) PILOT LAMPS
Work tool mode pilot lamp Message display

Work mode pilot lamp Travel speed pilot lamp
Power/User mode pilot lamp 4
Auto idle pilot lamp
Power max pilot lamp Maintenance pilot lamp
Preheat pilot lamp Fuel warmer pilot lamp
Warming up pilot lamp Decel
Decel pilot
pilotlamp
lamp
21093CD09
(1) Mode pilot lamps

No Mode Pilot lamp Selected mode
Heavy duty power work mode
1 Power mode Standard power mode
Economy power mode
2 User mode User preferable power mode
General operation mode
3 Work mode Breaker operation mode
Crusher operation mode
Low speed traveling

4 Travel mode
High speed traveling
5 Auto idle mode Auto idle
4
6 Work tool mode Oil flow level of breaker or crusher mode
7 Message display "Setting is completed" display after selection
(2) Power max pilot lamp

Η The lamp will be ON when pushing power max switch on the
LH RCV lever.
Θ The power max function is operated maximum 8 seconds.
ö Refer to the page 3-38 for power max function.
21093CD38
3-7
(3) Preheat pilot lamp
Η Turning the start key switch ON position starts preheating in
cold weather.
Θ Start the engine after this lamp is OFF.
21093CD39
(4) Warming up pilot lamp

Η This lamp is turned ON when the coolant temperature is below
30˚C (86˚F ).
Θ The automatic warming up is cancelled when the engine
coolant temperature is above 30˚C, or when 10 minutes have
passed since starting the engine.
21093CD40
(5) Decel pilot lamp

Η Operating one touch decel switch on the RCV lever makes the
lamp ON.
Θ Also, the lamp will be ON and engine speed will be lowered
automatically to save fuel consumption when all levers and
pedals are at neutral position, and the auto idle function is
21093CD41
selected.
ö One touch decel is not available when the auto idle pilot lamp
is turned ON.
ö Refer to the page 3-38.
(6) Fuel warmer pilot lamp

10˚C (50˚F ) or the hydraulic oil temperature 20˚C (68˚F ).
Θ The automatic fuel warming is cancelled when the engine
coolant temperature is above 60˚C, or the hydraulic oil temper-
ature is above 45˚C since the start switch was ON position.
21093CD43
(7) Maintenance pilot lamp

Η This lamp will be ON when the consuming parts are needed to
change or replace. It means that the change or replacement
interval of the consuming parts remains below 30 hours.
Θ Check the message in maintenance information of main menu.
Also, this lamp lights ON for 3 minutes when the start switch is
21093CD44
ON position.
3-8
5) SWITCHES
Power/User mode Auto idle pilot lamp

pilot lamp
Work mode Travel speed pilot lamp
pilot lamp
Power mode switch Escape(previous or parent menu)

Rear camera(option)
Work mode switch Auto idle/Buzzer stop switch
User mode switch Travel speed switch
Select switch
21093CD45
ö When the switches are selected, the pilot lamps are displayed on the LCD. Refer to the page
3-7 for details.
(1) Power mode switch

Η This switch is to select the machine power mode and selected
power mode pilot lamp is displayed on the pilot lamp position.
ÂP : Heavy duty power work.
ÂS : Standard power work.
ÂE : Economy power work.
21093CD45A Θ The pilot lamp changes E Ą S Ą P Ą E in order.
(2) Work mode switch

Η This switch is to select the machine work mode, which shifts
from general operation mode to optional attachment operation
mode.
Â : General operation mode
Â : Breaker operation mode (if equipped)
21093CD45C
Â : Crusher operation mode (if equipped)
ÂNot installed : Breaker or crusher is not installed.
ö Refer to the page 4-10 for details.
3-9
(3) User mode switch
Η This switch is used to memorize the current machine operating
status in the MCU and activate the memorized user mode.
ÂMemory : Push more than 2 seconds.
ÂAction : Push within 2 seconds.
ÂCancel : Push this switch once more within 2 seconds.
21093CD45D Θ Refer to the page 3-12 for another set of user mode.
(4) Select switch

Η This switch is used to select or change the menu and input
value.
Θ Knob push
ÂLong (over 2 sec) : Return to the operation screen
ÂMedium (0.5~2 sec) : Return to the previous screen
21093CD45E ÂShort (below 0.5 sec) : Select menu
③ Knob rotation
This knob changes menu and input value.
ÂRight turning : Down direction / Increase input value
ÂLeft turning : Up direction / Decreased input value
(5) Auto idle/ buzzer stop switch

Η This switch is used to activate or cancel the auto idle function.
ÂPilot lamp ON : Auto idle function is activated.
ÂPilot lamp OFF : Auto idle function is cancelled.
Θ The buzzer sounds when the machine has a problem.
In this case, push this switch and buzzer stops, but the
21093CD45F
warning lamp blinks until the problem is cleared.
(6) Travel speed control switch

Η This switch is used to select the travel speed alternatively.
Â : High speed
Â : Low speed
21093CD45G
(7) Escape/Camera switch

Η This switch is used to return to the previous menu or parent
menu.
Θ In the operation screen, pushing this switch will display the
view of the camera on the machine (if equipped).
Please refer to page 3-22 for the camera.
21093CD45H
Ι If the camera is not installed, this switch is used only ESC
function.
3-10
6) MAIN MENU
Press
21093CD64
21093CD64B
21093CD64A
ö Please refer to select switch, page 3-10 for selection and change of menu and input value.
(1) Structure
No Main menu Sub menu Description
Work tool Breaker, Crusher, Not installed
U mode power User mode only
Boom/Arm speed Boom speed, Arm speed
1
Auto power boost Enable, Disable
Mode Initial mode Default, U mode
21093CD64D Cluster switch (back up) Switch function
Active fault MCU
Logged fault MCU
Delete logged fault All logged fault delete, Initialization canceled
2
Monitoring (analog) Machine information
Monitoring
Monitoring Monitoring (digital) Switch status, Output status
21093CD64E Operating hours Operating hours for each mode
Maintenance information Replacement, Change interval oils and filters
Machine security ESL mode setting, Password change
Machine Information Cluster, MCU, Engine, Machine
3
A/S phone number A/S phone number, A/S phone number change
Management Service menu
Management Power shift, Hourmeter start, Replacement history,
21093CD64F Update
Display item Engine speed, Tripmeter A, Tripmeter B, Tripmeter C
Clock Clock
Brightness Manual, Auto
4 Unit Temperature, Pressure, Flow, Date format
Language Korean, English, Chinese
Display
Display
Screen type A type, B type
21093CD64G
Tripmeter 3 kinds (A, B, C)

DMB (-#0547) DMB select, DAB select, Channel scan, Exit
Entertainment (-#0547) Play MP4, codec.
5
Camera setting Basic direction, Display switching, Full screen
Utilities Message box Record for fault, attachment etc.
21093CD64H
3-11
(2) Mode setup
Η Work tool
21093CD65
21093CD65A 21093CD65B
A B
· A : Select one installed optional attachment.

· B : Max flow - Set the maximum flow for the attachment.
Flow level - Reduce the operating flow from maximum flow.
Breaker - Max 7 steps, Reduced 10 lpm each step.
Crusher - Max 4 steps, Reduced 20 lpm each step.
※ The flow level is displayed with the work mode pilot lamp.
② U mode power
Power
Step Engine Idle speed
speed (rpm) shift
( ) (rpm) (bar)
1 1500 1000 (low idle) 0
2 1600 1050 3
21093CD65D 3 1700 1100 6
4 1800 1150 (decel rpm) 9
21093CD65E
5 1850 1200 12
· Engine high idle rpm, auto idle rpm and pump torque 6 1900 1250 16
(power shift) can be modulated and memorized 7 1950 1300 20
separately in U-mode. 8 2000 1350 26
· U-mode can be activated by user mode switch. 9 2050 1400 32
10 2100 1450 38
③ Boom/Arm speed
21093CD65F
21093CD65G
· Boom speed
- Control type
Manual - Boom up speed is fixed as set steps.
Auto - Boom up speed is automatically adjusted as working conditions by the MCU.
- Speed setting - Boom up speed is increased as much as activated steps.
· Arm speed
- Regeneration - Arm regeneration function can be activated or cancelled.
Enable - Arm in speed is up.
Disable - Fine operation.
3-12
Κ Auto power boost
21093CD65L
21093CD65M
· The power boost function can be activated or cancelled.

· Enable - The digging power is automatically increased as working conditions by the MCU.
It is operated max 8 seconds.
· Disable - Not operated.
Λ Initial mode
21093CD65P
21093CD65Q
· Default - The initial power mode is set E mode when the engine is started.
· U mode - The initial power mode is set U mode when the engine is started.
Μ Cluster switch (back up)
21093CD65S
21093CD65T
- The cluster switch can be selected and changed by this menu when the switches are
abnormal on the cluster.
- In order to exit "Cluster switch" mode, please put the cursor on the ESC/CAM switch by
turning the select switch and push the select switch.
- In "Cluster switch", other switches except "Select switch" do not work.
3-13
(3) Monitoring
Η Active fault
21093CD66
21093CD66A-1 21093CD66B
· The active faults of the MCU can be checked by this menu.
Θ Logged fault
21093CD66C
21093CD66D-1 21093CD66E
· The logged faults of the MCU can be checked by this menu.
Ι Delete logged fault
21093CD66F
21093CD66G 21093CD66H
· The logged faults of the MCU can be deleted by this menu.
Κ Monitoring
Monitoring(Analog)
21093CD66J
21093CD66K 21093CD66L
· The machine status such as the engine rpm, oil temperature, voltage and pressure etc. can
be checked by this menu.
3-14
Λ Monitoring (digital)
21093CD66M
21093CD66N 21093CD66P
· The switch status or output status can be confirmed by this menu.

· The activated switch or output pilot lamps are light ON.
Μ Operating hours
21093CD66Q
21093CD66R
· The operating hour of each mode can be confirmed by this menu.
3-15
(4) Management
Η Maintenance information
21093CD67
21093CD67A
21093CD67Q 21093CD67R
21093CD67S 21093CD67T
· Alarm( ) : Gray - Normal

Yellow - First warning
Red - Second warning
· Replacement : The elapsed time will be reset to zero (0).
· Change interval : The change or replace interval can be changed in the unit of 50 hours.
· OK : Return to the item list screen.
· Change or relpace interval
No Item Interval
1 Engine oil 500
2 Final gear oil 1000
3 Swing gear oil 1000
4 Hydraulic oil 5000
5 Pilot line filter 1000
6 Drain filter 1000
7 Hydraulic oil return filter 1000
8 Engine oil filter 500
9 Fuel filter 500
10 Pre-filter 500
11 Hydraulic tank breather 250
12 Air cleaner (inner) 500
13 Radiator coolant 2000
14 Swing gear pinion grease 1000
3-16
Θ Machine security
21093CD67C
21093CD67D 21093CD67E
· ESL mode
- ESL : Engine Starting Limit
- ESL mode is desingned to be a theft deterrent or will
prevent the unauthorized operation of the machine.
- If the ESL mode was selected Enable, the password will
be required when the start switch is turned ON.
21093CD67EE
- Disable : Not used ESL function
Enable (always) : The password is required whenever the
operator start engine.
Enable (interval) : The password is required when the oper-
ator start engine first. But the operator
restarts the engine within the interval
time, the password is not required.
The interval time can be set maximum 4 21093CD67H
hours.
21093CD67U Enter the current password 21093CD67V
· Password change
- The password is 5~10 digits.
Enter the new password 21093CD67VV
21093CD67X 21093CD67XX
The new password is stored in the MCU. Enter the new password again
3-17
Ι Machine Information
21093CD67F
21093CD67G
· This can confirm the identification of the cluster, MCU, engine and machine.
Κ A/S phone number
21093CD67J
21093CD67K 21093CD67L
21093CD67Z 21093CD67Y
Λ Service menu
21093CD67M
21093CD67N 21093CD67P
Enter the password
21093CD67ZZ
· Power shift (standard/option) : Power shift pressure can be set by option menu.
· Hourmeter start : Operating hours since the machine line out can be checked by this menu.
· Replacement history : Replacement history of the MCU and cluster can be checked by this
menu.
· Update : Firm ware can be upgraded by this menu. (the USB port is located under the
cluster)
3-18
(5) Display
Η Display item
21093CD68
21093CD68A 21093CD68W
21093CD68B 21093CD68E
Center display
Center display
· The center display type of the LCD can be selected by this menu.
· The engine speed or each of the tripmeter (A,B,C) is displayed on the center display.
Θ Clock
21093CD68C
21093CD68D
· The first line's three spots "**/**/****" represent Month/Day/Year each.

· The second line shows the current time. (0:00~23:59)
3-19
Ι Brightness
21093CD68F
21093CD68G 21093CD68H
Manual (1st~10th step)
21093CD68J 21093CD68K
Auto (day/night)
※ If "Auto" is chosen, brightness for day and night can be differently set up. Also by using the
bar in lower side, users can define which time interval belongs to day and night.
(in bar figure, gray area represents night time while white shows day time)
Κ Unit
21093CD68L
21093CD68M 21093CD68N
· Temperature : ˚C ↔ ˚F
· Pressure : bar ↔ MPa ↔ kgf/cm2
· Flow : lpm ↔ gpm
· Date format : yy/mm/dd ↔ mm/dd/yy ↔ dd-Mar-yy
Λ Language
21093CD68R
21093CD68S 21093CD68T
· User can select preferable language and all displays are changed the selected language.
3-20
Μ Screen type
21093CD68U
21093CD68V 21093CD68W
A Type Standard
21093CD68Y
B Type 21093CD68X Option
(6) Utilities
Η Tripmeter
21093CD69
21093CD69A 21093CD69B
· Maximum 3 kinds of tripmeters can be used at the same time.

· Each tripmeter can be turned on by choosing "Start" while it also can be turned off by
choosing "Stop".
· If the tripmeter icon is activated in the operation screen, it can be controlled directly there.
Θ DMB (-#0547)
21093CD69C
21093CD69D 21093CD69E
· DMB select : TV channel can be selected by this menu.

· DAB select : Audio channel can be selected by this menu.
· Channel scan : This menu can be used other region for TV/Audio.
· Exit : Exit DMB menu
3-21
Ι Entertainment (-#0547)
· Play MP4 or codec file of external hard disk through USB port.
· The USB port is located under the cluster.
21093CD69F
21093CD69G
Κ Camera setting
21093CD69J
21093CD69K 21093CD69L
· Three cameras can be installed on the machine.

· The display order can be set by this menu.
21093CD69M 21093CD69N
· If the camera was not equipped, this menu is not useful.

· In the operation screen, if the ESC/CAM switch is pushed, the first ordered display camera
will be viewed.
· Turnning the select switch in clockwise direction, the next ordered will be shown and in
counter-clockwise direction, the previously ordered will be shown.
· Push the select switch, the displayed screen will be enlargement.
Λ Message box
· The history of the machine operating status can be checked by this menu.
21093CD69Q
21093CD69R
3-22
2. CLUSTER (TYPE 2)
1) MONITOR PANEL
The monitor panel consists of LCD and lamps as shown below, to warn the operator in case of
abnormal machine operation or conditions for the appropriate operation and inspection.
Â LCD : Indicate operating status of the machine.
Â Warning lamp : Indicate abnormality of the machine (red).
Â Pilot lamp : Indicate operating status of the machine (amber).
ö The monitor installed on this machine does not entirely guarantee the condition of the
machine. Daily inspection should be performed according to chapter 6, Maintenance.
ö When the monitor provides a warning immediately check the problem, and perform the
required action.
LCD(Refer to the page 3-24

3-24 for
fordetails)
details)
Warning lamp Pilot lamp

(Refer to the page 3-30
3-30 (Refer to the page 3-30
3-30
for details) for details)
2209S3CD02
öThe warning lamp lights ON and the buzzer sounds when the machine has a problem.
In this case, press the buzzer stop switch and buzzer stop, but the warning lamp lights until
the problem is cleared.
3-23
2) LCD MAIN OPERATION DISPLAY
Default screen
screen screen
Option screen 1 Time display
2 2
1 1 2 RPM display
4
4
5
3 Hydraulic oil temperature gauge
3 3
5 4 Fuel level gauge
1607A3CD02A 1607A3CD02B 5 Engine coolant temperature gauge
(1) Time display

Η This displays the current time.
ö Refer to the page 3-28 to set time for details.
1607A3CD02C
(2) RPM display

Η This displays the engine rpm.
1607A3CD02C
(3) Hydraulic oil temperature gauge

Η This gauge indicates the temperature of hydraulic oil in 12 step
12th step
gauge.
·1st step : Below 30˚C (86˚F)
·2nd~10th step : 30-105˚C (86-221˚F)
1st step ·11th~12th step : Above 105˚C (221˚F)
1607A3CD02D
Θ The gauge between 2nd and 10th steps illuminates when
operating.
Ι Keep idling engine at low speed until the gauge between 2nd
and 10th steps illuminates, before operation of machine.
Κ When the gauge of 11th and 12th steps illuminates, reduce
the load on the system. If the gauge stays in the 11th~12th
steps, stop the machine and check the cause of the problem.
(4) Fuel level gauge
1st step Η This gauge indicates the amount of fuel in the fuel tank.
Θ Fill the fuel when the 1st step or fuel icon blinks in red.
ö If the gauge illuminates the 1st step or fuel icon blinks in
1607A3CD02E
(5) Engine coolant temperature gauge
12th step
Η This gauge indicates the temperature of coolant in 12 step
gauge.
Â1st step : Below 30˚C (86˚F)
Â2nd~10th step : 30-105˚C (86-221˚F)
1st step
Â11th~12th step : Above 105˚C (221˚F)
1607A3CD02F
Θ The gauge between 2nd and 10th steps illuminates when
operating.
Ι Keep idling engine at low speed until the gauge between 2nd
and 10th steps illuminates, before operation of machine.
Κ When the gauge of 11th and 12th steps illuminates, turn OFF
the engine, check the radiator and engine.
3-24
3) WARNING OF MAIN OPERATION SCREEN
(1) Warning display
Η Engine coolant temperature
This lamp blinks and the buzzer sounds
when the temperature of coolant is over
the normal temperature 105˚C (221˚F).
Check the cooling system when the lamp
blinks.
Θ Fuel level
when the level of fuel is below 69˶ (18.2
U.S. gal).
Fill the fuel immediately when the lamp
blinks.
Ι Hydraulic oil temperature
This warning lamp operates and the
buzzer sounds when the temperature of
hydraulic oil is over 105˚C (221˚F).
Check the hydraulic oil level when the
lamp blinks.
Check for debris between oil cooler and
radiator.
Κ All gauge
when the all gauge is abnormal.
Check the each system when the lamp
blinks.
Λ Communication error
Communication problem between MCU
and cluster makes the lamp blinks and
the buzzer sounds.
Check if any fuse for MCU burnt off.
If not check the communication line
between them.
(2) Pop-up icon display
No Switch Selected mode Interval No Switch Selected mode Interval
1 Work mode General work 3 Auto Light ON

switch mode deceleration
switch
Heavy duty Light OFF
work mode
2 Power mode High power 4 Travel speed Low speed

switch work mode control
switch
Standard power High speed
work mode
3-25
4) LCD
1 : LCD
SYSTEM MENU
: Escape,
1
Monitoring Diagnosis Management
2
Settings Display User Mode
Return to the previous menu
3 : Down / Left Direction
4 : Up/Right Direction
: Select (enter)
5
2 Activate the currently chosen item
4
3 5
2209S3CD05
(1) Main menu

1 2 3 4
1 : Menu information
: Monitoring
2
- Equipment, Switch, Output
: Diagnosis
3
- Current error, Recorded error
5 6 7 4 : Maintenance
2507A4OP94
: Settings
5 - Time set, Dual mode
- System lock (reserved)
: Display
6
- Operation skin, Brightness, Language
7 : User mode
3-26
(2) Display map
Η Monitoring
Θ Diagnosis
a. Protocol type 1
(Error display)
(Recorded error delete)
3-27
b. Protocol type 2
- If there are more than 2 error codes, each one can be displayed by pressing or switch
respectively.
- 3 error codes (ΗSPN200200, ΘFMI06, ΙSPN6789, ΚFMI04, Λ345) display.
Η Θ Λ No change
Η Ι Κ
Η Ι Ι
Ι Maintenance
Κ Setting
a. Time set
: Adjusting
: Setting
b. System lock - Reserved
3-28
c. Dual mode
- Changing the MCU mode
Λ Display
a. Operation skin
b. Brightness
c. Language
Μ User mode
Usermode(U) is not selected.
: Adjusting : Adjusting : Adjusting

: Setting : Setting : Setting
3-29
5) WARNING AND PILOT LAMP
(1) Engine oil pressure warning lamp
Η This lamp blinks and the buzzer sounds after starting the
engine because of the low oil pressure.
Θ If the lamp blinks during engine operation, shut OFF engine
immediately. Check oil level.
21073CD07
(2) Air cleaner warning lamp

Η This lamp blinks and the buzzer sounds when the filter of air
cleaner is clogged.
Θ Check the filter and clean or replace it.
21073CD08
(3) CPU controller check warning lamp

Η If any fault code is received from MCU, this lamp blinks and the
buzzer sounds.
Θ Check the communication line between MCU and cluster.
21073CD10
(4) Battery charging warning lamp

Η This lamp blinks and the buzzer sounds when the starting
switch is ON, it is turned OFF after starting the engine.
Θ Check the battery charging circuit when this lamp blinks during
engine operation.
21073CD13
(5) Overload warning lamp (opt)

Η When the machine is overload, the overload warning lamp
blinks during the overload switch is ON.
21073CD15
3-30
(6) Power max pilot lamp
Η The lamp will be ON when pushing power max switch on the LH
RCV lever.
21073CD11
(7) Decel pilot lamp

Η Operating auto decel or one touch decel makes the lamp ON.
Θ The lamp will be ON when pushing one touch decel switch on
the LH RCV lever.
21073CD17
(8) Warming up pilot lamp

30˚C (86˚F).
Θ The automatic warming up is cancelled when the engine cool-
ant temperature is above 30˚C, or when 10 minutes have
passed since starting.
21073CD18
(9) Preheat pilot lamp

Η Turning the start key switch ON position starts preheating in cold
weather.
Θ Start the engine as this lamp is OFF.
21073CD12
3-31
6) SWITCH PANEL
Work mode switch Power mode switch
Travel speed switch

User mode switch
Buzzer stop switch

Auto deceleration switch Select switch
2209S3CD10
ö When the switches (Work mode, Power mode, Auto decel, Travel speed control) are selected,
the pop-up icon is displayed on the LCD.
Refer to the page 3-25 for details.
(1) Work mode switch

Η This switch is to select the machine operation mode, which
shifts from general operation mode to heavy operation mode
and breaker mode in a raw by pressing the switch.
Â : Heavy duty work mode
Â : General work mode
2209S3CD11 ö Refer to the page 4-16 for details.
(2) User mode switch

Η This switch is to select the maximum power or user mode.
ÂM : Maximum power
ÂU : Memorizing operators preferable power setting.
1607A3CD21
3-32
(3) Auto deceleration switch
Η This switch is used to actuate or cancel the auto deceleration
function.
Θ When the switch actuated and all control levers and pedals are
at neutral position, engine speed will be lowered automatically
to save fuel consumption.
1607A3CD22
ÂLight ON : Auto deceleration function is selected.
ÂLight OFF : a. Auto deceleration function is cancelled so that
the engine speed increased to previous
setting value.
b. One touch decel function is available.
(4) Power mode switch

Η The lamp of selected mode is turned ON by pressing the
switch ( ).
ÂH : High power work.
ÂS : Standard power work.
21073CD23
(5) Travel speed control switch

Η This switch is to control the travel speed which is changed to
high speed (rabbit mark) by pressing the switch and low speed
(turtle mark) by pressing it again.
21073CD24
(6) Buzzer stop switch

Η When the starting switch is turned ON first, normally the alarm
buzzer sounds for 2 seconds during lamp check operation.
Θ The red lamp lights ON and the buzzer sounds when the
machine has a problem.
In this case, press this switch and buzzer stops, but the red
1607A3CD25
lamp lights until the problem is cleared.
(7) Select switch

Η This switch is used to enter main menu and sub menu of LCD.
1607A3CD25A
3-33
3. SWITCHES
Cab light switch Quick clamp switch

Travel alarm switch Beacon switch
Washer switch Overload switch
Wiper switch Breaker switch
Main light switch USB socket
B
A
C
SEAT(OPT)
Heated seat
switch
Air compressor switch

Accel dial switch
Horn switch
Breaker operation switch
Start switch
Master switch
One touch decel switch

Power max switch
2209S3CD47
1) STARTING SWITCH
(1) There are three positions, OFF, ON and START.
Â(OFF) : None of electrical circuits activate.
Â(ON) : All the systems of machine operate.
Â(START) : Use when starting the engine.
Release key immediately after starting.
ö If you turn ON the starting switch in cold weather, the fuel warmer
21073CD27
is automatically operated to heat the fuel by sensing the coolant
temperature. Start the engine in 1~2 minutes after turning ON the
starting switch. More time may take according to ambient
temperature.
ö Key must be in the ON position with engine running to maintain
electrical and hydraulic function and prevent serious machine
damage.
3-34
2) MASTER SWITCH
(1) This switch is used to shut off the entire electrical system.
(2) I : The battery remains connected to the electrical system.
O : The battery is disconnected to the electrical system.
ö Never turn the master switch to O (OFF) with the engine running.
Engine and electrical system damage could result.
OFF
OFF
13033CD81
3) ACCEL DIAL SWITCH

(1) There are 10 dial setting.
Increase
(2) Setting 1 is low idle and setting 10 is high idle.
ÂBy rotating the accel dial to right : Engine speed increases
ÂBy rotating the accel dial to left : Engine speed decreases
Decrease
235Z93CD46A
4) MAIN LIGHT SWITCH

(1) This switch used to operate the head light and work light.
Pilot lamp(2nd)
Â Press the switch once, the head light comes ON and the 1st pilot
lamp ON.
Â Press the switch once more, the work light comes ON and the 2nd
pilot lamp ON.
Pilot lamp(1st) Â Press the switch again, return to a first step position.
21093CD46B
Â Press the switch more than one second to turn off lights.
5) WIPER SWITCH
(1) This switch used to operate wiper.
Pilot lamp(2nd)
Â Press the switch once the wiper operates intermittently and the 1st
pilot lamp comes ON.
Â Press the switch once more, the wiper operates low speed and
the 2nd pilot lamp comes ON.
Pilot lamp(1st) Â Press the switch again return to a first step position.
21093CD46C
Â Press the switch more than one second to turn off wiper.
6) WASHER SWITCH
(1) The washer liquid is sprayed and the wiper is operated only while
Pilot lamp
pressing this switch.
(2) The pilot lamp is turned ON when operating this switch.
21093CD46D
3-35
7) TRAVEL ALARM SWITCH
(1) This switch is to activate travel alarm function surrounding when the
Pilot lamp
machine travels to forward and backward.
(2) On pressing this switch, the alarm operates only when the machine
is traveling.
21093CD46F
8) CAB LIGHT SWITCH (option)
Pilot lamp
(1) This switch turns ON the cab light on the cab.
B
A
C
21093CD46G
9) OVERLOAD SWITCH (option)

(1) When this switch turned ON, buzzer makes sound and overload
OFF
ON warning lamp comes ON in case that the machine is overload.
(2) When it turned OFF, buzzer stops and warning lamp goes out.
21093CD46H
10) QUICK CLAMP SWITCH (option)

Safety button (1) This switch is used to engage or disengage the moving hook on
quick clamp.
Lock Unlock
21093CD46J
11) BEACON SWITCH (option)

(1) This switch turns ON the rotary light on the cab.
(2) The indicator lamp is turned ON when operating this switch.
21093CD46L
3-36
12) BREAKER SELECTION SWITCH (option)
(1) This switch is used to select breaker.
ö The breaker operates only when this switch is selected.
3009SH3CD03
13) USB SOCKET

(1) MP3 files are played when a USB device is connected to the USB
port.
(2) In addition, the AUX port enables headphone and other devices.
3009SH3CD04
14) HEATED SEAT SWITCH (option)

(1) This switch is used to heat the seat.
ÂHeater ON : 10±3.5 ˚C
ÂHeater OFF : 20±3 ˚C
O
I (2) On pressing the switch, the indicator lamp is turned ON.
21093CD46M
15) HORN SWITCH

(1) This switch is at the top of right side control lever.
On pressing, the horn sounds.
Horn switch
RH RCV-lever
21093CD46N
16) BREAKER OPERATION SWITCH

Breaker (1) On pressing this switch, the breaker operates only when the breaker
operation
switch operation mode is selected.
RH RCV-lever
21093CD46P
3-37
17) ONE TOUCH DECEL SWITCH
(1) This switch is used to actuate the deceleration function quickly.
One touch
decel switch
(2) The engine speed is increased to previous setting value by pressing
the switch again.
(3) One touch decel function is available only when the auto idle pilot
lamp is turned OFF.
LH RCV-lever
21093CD46Q
18) POWER MAX SWITCH

(1) This switch activate power max function.
Power max When this switch is kept pressed, hydraulic power of work equipment
switch
will be increased to approx 110 percent during 8 seconds.
(2) After 8 seconds, function is cancelled automatically even the switch
keeps pressed.
LH RCV-lever
21093CD46R
ö Do not use for craning purposes.
19) AIR COMPRESSOR SWITCH (option)

(1) This switch is used to activate the air compressor.
OFF ON
(2) The indicator lamp is turned on when operating this switch.
IR
A
17W93CD46N
3-38
4. LEVERS AND PEDALS
RH control lever
Travel lever
LH control lever
Travel pedal
Safety lever
Seat & console box adjust lever LH adjusting lever
3009SH3CD05
1) LH CONTROL LEVER
(1) This joystick is used to control the swing and the arm.
(2) Refer to operation of working device in chapter 4 for details.
21093CD48A
2) RH CONTROL LEVER
(1) This joystick is used to control the boom and the bucket.
(2) Refer to operation of working device in chapter 4 for details.
21093CD48B
3-39
3) SAFETY LEVER
(1) All control levers and pedals are disabled from operation by locating
the lever to lock position as shown.
ö Be sure to lower the lever to LOCK position when leaving from
Unlock
operator's seat.
(2) By pull lever to UNLOCK position, the machine is operational.
Lock ö Do not use the safety lever for handle when getting on or off the
21093CD48C
machine.
4) TRAVEL LEVER
(1) This lever is mounted on travel pedal and used for traveling by hand.
The operation principle is same as the travel pedal.
(2) Refer to traveling of the machine in chapter 4 for details.
21093CD48D
5) TRAVEL PEDAL
(1) This pedal is used to move the machine forward or backward.
(2) If left side pedal is pressed, left track will move.
If right side pedal is pressed, right track will move.
(3) Refer to traveling of machine in chapter 4 for details.
21093CD48E
6) SEAT AND CONSOLE BOX ADJUST LEVER

(1) This lever is used to move the seat and console box to fit the
contours of the operator's body.
(2) Pull the lever to adjust forward or backward over 170 mm (6.7").
Adjust lever
21093CD48F
3-40
5. AIR CONDITIONER AND HEATER
ÿ FULL AUTO AIR CONDITIONER AND HEATER (standard)
Full auto air conditioner and heater system automatically keeps the optimum condition in accordance
with operator's temperature configuration sensing ambient and cabin inside temperature.
ö Refer to the page 3-45 for semi auto air conditioner and heater.
Â Location of air flow ducts
Fresh air switch LCD Mode switch
Auto switch
Power OFF switch
Fan speed switch Air conditioner switch
Air recirculation switch Temperature control switch

3009SH3CD06
3-41
1) POWER OFF SWITCH
(1) This switch makes the system and the LED OFF.
Just before the power OFF, set values are stored.
(2) Default setting values
Function Air conditioner In/outlet LCD Temperature Mode
Value OFF Inlet OFF Previous sw OFF Previous sw OFF

370073CD54
2) AUTO SWITCH
(1) Turn the starting switch to ON position, LCD lights ON.
Auto air conditioner and heater system automatically keeps the
optimum condition in accordance with operator's temperature
configuration sensing ambient and cabin inside temperature.
(2) This switch can restart system after system OFF.
370073CD52
3) AIR CONDITIONER SWITCH (compressor switch)

(1) This switch turns the compressor and the LCD ON.
(2) In accordance with the temperature sensed by duct (evaporator)
sensor, compressor turns ON or OFF automatically.
ö Air conditioner operates to remove vapor and drains water
through a drain hose. Water can be sprayed into the cab in case
370073CD53
that the drain cock at the ending point of drain hose has a
problem.
In this case, exchange the drain cock.
4) FAN SPEED SWITCH

(1) Fan speed is controlled automatically by setted temperature.
(2) This switch controls fan speed manually.
Â There are 8 up/down steps to control fan speed.
Â The maximum step or the minimum step beeps 5 times.
(3) This switch makes the system ON.
370074CD56
3-42
5) TEMPERATURE CONTROL SWITCH
(1) Setting temperature indication ( Lo, 18~31˚C, Hi, scale : 1˚C)
(2) Max cool and max warm beeps 5 times.
(3) The max cool or the max warm position operates as following table.
Temperature Compressor Fan speed In/Outlet Mode
370074CD57
Max cool ON Max (Hi) Recirculation Vent
Max warm OFF Max (Hi) Fresh Foot
(4) Temperature unit can be changed between celsius (˚C) and fahren-
heit (˚F)
Η Default status (˚C)
Θ Push Up/Down temperature control switch simultaneously more
than 5 second displayed temperature unit change (˚C Ą˚F)
6) MODE SWITCH
(1) Operating this switch, it beeps and displays symbol of each mode in
order.
ÂA type : Vent Ą Vent/Foot Ą Foot Ą Foot/Def Ą Vent
Vent Vent/Foot Foot Foot/Def
Mode switch
370074CD50 A ú ú
Outlet B ú ú ú
C ú
ÂB type : Vent Ą Vent/Foot Ą Def/Foot Ą Def/Vent Ą Def/Vent/Foot
Vent Vent/Foot Def/Foot Def/Vent Def/Vent/Foot
Mode switch
A ú ú ú ú
Outlet B ú ú ú
C ú ú ú
(2) When defroster mode operating, FRESH AIR/AIR RECIRCULATION
switch turns to FRESH AIR mode and air conditioner switch turns
ON.
7) FRESH AIR/AIR RECIRCULATION SWITCH

(1) It is possible to change the air-inlet method.
Η Fresh air ( )
Inhaling air from the outside.
ö Check out the fresh air filter periodically to keep a good efficiency.
Θ Air recirculation ( )
It recycles the heated or cooled air to increase the energy efficiency.
36073CD58
ö Change air occasionally when using recirculation for a long time.
ö Check out the recirculation filter periodically to keep a good
efficiency.
3-43
8) SELF DIAGNOSIS FUNCTION
(1) Procedure
Starting switch ON
Press the air recirculation button over 5 times within

2 seconds during pressing the AUTO switch
All symbol of LCD blink 5 times
Switch OFF
Error check System OFF
Press AUTO switch
Cancelled diagnosis function(normal function)

3607A3CD69
(2) Error check

Â The corresponding error code flickers on the setup temperature display panel, the other symbol
bol will turn OFF.
Â Error code flickers every 0.5 second.
Â If error code is more than two, each code flickers 2 times in sequence.
Â Error code
Error code Description Error code Description
11 Cabin inside sensor 15 Temp actuator

12 Ambient sensor 16 Mode actuator 1
13 Coolant temp sensor 17 Mode actuator 2
14 Duct (evaporator) sensor 18 Intake actuator
(3) Fail safe function

Error description Fail safe function
Cabin inside sensor (11) 25˚C alternate value control

Ambient sensor (12) 20˚Calternate value control
Coolant temp sensor (13) More than 10 minutes after engine start up, the alternate value is ON
Duct (evaporator) sensor (14) 1˚Calternate value control
If opening amount is 0 %, the alternate value is 0 %
Temp actuator (15)
If not, the alternate value is 100 %
Mode actuator 1, 2 (16, 17) The alternate value is Vent
3-44
ÿ SEMI AUTO AIR CONDITIONER AND HEATER (option)
Semi auto air conditioner and heater are equipped for pleasant operation against outside tempera-
ture and defrost on window glass.
ö Refer to the page 3-41 for full auto air conditioner and heater.
Â Location of air flow ducts
CALL
MUTE
MODE
V
SEEK
VOL
Switch panel
Inlet change over switch
Outlet change over switch

Temperature control switch
Fan speed switch
Power switch
Air conditioner switch
21093CD53
3-45
1) POWER SWITCH
(1) This switch makes the system and the LED simultaneously ON or OFF.
(2) Default setting values
Function Air conditioner Fan speed Temperature Outlet Inlet
Value OFF 1 Max cool Face Recirculation
21073CD53
2) AIR CONDITIONER SWITCH (compressor switch)

(1) Operating this switch turns the compressor and the LED
simultaneously ON or OFF.
(2) In accordance with the evaporator temperature, compressor turns on
or off automatically without changing LED state.
ö Air conditioner operates to remove vapor and drains water
21073CD53
through a drain hose. Water can be sprayed into the cab in case
that the vacuum valve of drain hose has a problem.
In this case, exchange the vacuum valve.
3) FAN SPEED SWITCH

(1) It is possible to control the fan to four steps.
(2) The first step or the fourth step gives 5 times beeps.
21073CD52
4) TEMPERATURE CONTROL SWITCH

(1) There are 9 steps to control temperature from max cool to max warm
controlled up and down by 1 step.
(2) Max cool and max warm arouse 5 times beeps.
(3) For the max warm or the max cool it's better to be configured as
following table.
21073CD50
Temperature Air conditioner Fan speed Outlet Inlet
Max cool ON 4 Face Recirculation
Max warm OFF 3 Foot Fresh
3-46
5) OUTLET CHANGE OVER SWITCH
(1) There are four steps of air flow.
Mode
Switch position
A ú ú
21073CD51
Outlet B ú ú ú
C ú
(2) When defroster switch operating, INLET switch turns to FRESH

mode and air conditioner switch turns ON.
(3) In case of heating range (5~Max warm), air conditioner won't turns
ON.
6) INLET CHANGE OVER SWITCH

(1) It is possible to change the air-inlet method.
Η Fresh
Inhaling air from the outside to pressurize cab inside.
Fresh
ö Check out the fresh air filter periodically to keep a good efficiency.
Θ Recirculation
Recirculation It recycles the heated or cooled air to increase the energy efficiency.
21073CD49
ö Change air occasionally when using recirculation for a long time.
ö Check out the recirculation filter periodically to keep a good effi-
ciency.
(2) Recirculation function operates when the system is OFF but it can be
changed whenever needed.
3-47
6. OTHERS
Fuel tank
Seat
MCU Radio & USB player
Cigar lighter
RS232 service socket
12V socket
Service meter
Fuse & relay box
3009SH3CD07
1) CIGAR LIGHTER
(1) This can be used when the engine starting switch is ON.
(2) The lighter can be used when it springs out in a short while after
being pressed down.
※ Service socket
13033CD69
Use cigar lighter socket when you need emergency power.
Do not use the lighter exceeding 24V, 100W.
2) 12V SOCKET
(1) Utilize the power of 12V as your need and do not exceed power of
12 V, 30 W.
R5573CD49
3-48
3) RADIO AND USB PLAYER
14 LCD display 1 13
3 4 2 5 6 7 8 9 10 11 12
75793CD62
ÿFRONT
FRONT PANEL PRESENTATION
1 SEL -------- Sound function selection button 10 6 -------- Preset memory button 6
(audio selection) D+ --------------- Directory up
2 -------- Power and volume button 11 -------- Aux function
3 MODE -------- Mode button 12 BSM -------- Preset scan (PS)

(select RADIO / USB / AUX) Best station memory (BSM)
4 ------- UP / DOWN tuning button 13 MUTE -------- Audio mute button

14 AM/FM -------- AM / FM button (radio)
5 1 ------- Preset memory button 1
DISP ---------- ID3 v2 display
SCN ------------ File scan
RPT ------------ Repeat play selector
RDM ------------ Random play selector
D- ---------------- Directory down
3-49
ÿGENERAL
GENERAL
(1) Power and volume button
Η Power ON / OFF button
Press power button to turn the unit ON or OFF shortly.
When the power is ON, the previous mode (last memory) will
appear.
75793CD66 Θ Volume
olume up / down control
Turn volume up / down button right to increase the volume level. The
level will be shown in VOLUME xx on the LCD display. Turn it left to
decrease the volume level. After 5 seconds of volume indication,
display will return to the previous mode.
(2) Sound function selection button (audio selection)

Η This button is to adjust the sound. Each time you press power but-
ton shortly, LCD displays each mode as follows :
SEL
BASS TREBLE BAL BEEP LOUD VOLUME
75793CD65
ö When this button is pressed, LCD display shows selected function

for 5 seconds and then returns back to the previous mode. On
selected function, level can be controlled by turning this button. The
display will automatically return to normal indication in 5 seconds
after the last adjustment is made or when another function is acti-
vated.
Θ Bass
ass control
To adjust the bass level, first select the bass mode by pressing the
select button SEL
until BASS indication appears on the LCD display.
Within 5 seconds of choosing the bass mode, turn power button
right / left to adjust the bass level as desired.
The bass level will be shown on the LCD display from a minimum of
BASS –10 to a maximum of BASS +10.
The display will automatically return to the normal indication in 5
seconds after the last adjustment or when another function is acti-
vated.
Ι Treble
reble control
To adjust the treble level, first select the treble mode by pressing the
select button SEL
until TREBLE indication appears on the LCD dis-
play. Within 5 seconds of choosing the treble mode, turn power but-
ton right / left to adjust the treble level as desired.
The treble level will be shown on the LCD display from a minimum
of TREBLE -10 to a maximum of TREBLE +10.
vated.
3-50
Κ Balance
alance control
To adjust the left-right speaker balance, first select the balance
mode by pressing the select button SEL
until the BAL indication
appears on the LCD display.
Within 5 seconds of choosing the balance mode, turn power button
right / left to adjust the balance as desired.
The balance position will be shown on the LCD display from BAL
10L (full left) to BAL 10R (full right).
When the volume level between the left and right speakers is equal,
BAL L=R will be shown on the LCD display panel.
vated.
Λ Beep
eep control
To adjust the beep mode, first select the beep mode by pressing the
select button SEL
until BEEP indication appears on the LCD display.
The beep mode will be shown on the LCD display from BEEP 2ND,
BEEP OFF and BEEP ON by turning power button right / left.
vated.
Select BEEP ON when you wish to hear the BEEP sound whenever
any function button is pressed.
Select BEEP 2ND when you wish to hear the BEEP sound whenev-
er any tuner pre-set button and/or tune seek buttons are pressed for
more than 3 seconds.
Μ Loud
oud control
When listening to music at low volume levels, this feature will boost
the bass and treble response.
This action will compensate for the reduction in bass and treble per-
formance experienced at low volume.
To select the loudness feature, press select button until LOUD
SEL
ON or LOUD OFF is displayed, then turn power button left or right

to activate or deactivate loudness.
(3) Mode button

Η Press mode button to select RADIO / USB / AUX.
MODE
75793CD67
(4) Audio mute button

Η Press mute button momentarily to mute volume and MUTE
mark will blink on the LCD display.
MUTE Press the button again to return to the mode in use before the
mute mode was activated.
75793CD77
3-51
ÿRADIO
RADIO
(1) AM / FM / LW band selector
Η Each time this button is pressed, the radio button is changed.
Each time this button is pressed, LCD displays each band as
AM/FM follows :
FM1 FM2 FM3 AM LW
75793CD78
ö LW band is only available for Europe.
(2) Up / down tuning

Η To automatically select a radio station, momentarily press the up
tune seek button or down tune seek button for less than 3
seconds to search for the closest radio station.
To manually select a radio station, press the up tuning & down
75793CD68 tuning button for longer than 3 seconds.
The radio frequency will move up or down step by step each
time you press button.
(3) Station pre-set button

Η Pressing these buttons shortly will recall your favorite pre-set
1 2
radio stations.
To store your favorite stations into any of the 6 pre-set memories
3 4 in each band (AM/FM/LW), use the following procedure :
a. Turn the radio ON and select the desired band.
5 6 b. Select the first station to be pre-set using the manual up/
75793CD69~74 down or automatic seek tuning control button.
c. Press the chosen pre-set button to store your selected station
into and continue to hold it in. The beep sound will be
momentarily heard and the pre-set number will apear on the
LCD display indicating that the station is now set into that
pre-set memory position and can be recalled at any time, by
pressing that pre-set button.
3-52
(4) Pre-set scan (PS) / Best station memory (BSM) button
Η Pre-set scan (PS)
Press BSM button shortly to scan the 6 pre-set station stored the
BSM memories on each band (AM/FM/LW).
The unit will stop at each pre-set station (the pre-set number on the
75793CD76 LCD display will flash during pre-set scan operation) and remain on
the selected frequency. Press the button momentarily again to
remain on the station currently being heard.
Θ Best station memory (BSM)
Pressing BSM button for longer than 2 seconds will activate the
BSM tuning feature which will automatically scan and enter each
station into memory.
If you have already set the pre-set memories to your favorite
stations, activating the BSM tuning feature will erase those stations
and enter the new ones.
This BSM feature is most useful when traveling in a new area where
you are not familiar with the local stations.
ÿUSB
USB PLAYER
(1) USB function

There are two ways to play mp3 files in a USB device : using USB socket in the cab and the USB /
AUX cable connected to the front side of the player.
· Use of USB
USB socket
Η Connect a USB device, which saves mp3 files, to USB socket in the cabin.
Θ If a USB device has not been connected, MP3 files are automatically played when you insert it
into the USB port.
Ι If a USB device has connected, MP3 files are played when you press mode for USB.
· Use of USB / AUX cable (option)
75793CD81
Η Connect the USB/AUX cable to the player in order to play MP3 files in a USB device.
Θ If a USB device has not been connected, MP3 files are automatically played when you
insert it into the cable.
Ι If a USB device has connected, MP3 files are played when you press mode for USB.
3-53
(2) File selection & cue / review button
Η File
ile selection function
This button is used to select file up / down. Each time the forward
file select is pressed, file number is increased.
Each time the backward file select is pressed, file number is
75793CD68 decreased.
Θ Cue
ue / review functions
High-speed audible search of file on a USB can be made by this
button (the cue and review functions).
Press and hold the cue button to advance rapidly in the forward
direction or the review button to advance rapidly in the backward
direction.
(3) MP3 directory / file searching

Η The power button is used to select a particular directory and file.
Press and hold for more than 3 seconds while playing MP3 file.
Turn right / left the power button to search the directory. Press the button when you find the want-
ed directory.
For example, the directory search generally changes in two methods depending on the order of
writing as follows.
ÂMethod 1 : ROOT Dir01 Dir02 Dir03 Dir04 Dir05 Dir06 Dir07
ÂMethod 2 : ROOT Dir01 Dir02 Dir05 Dir03 Dir06 Dir04 Dir07
If you want to search the file in the located directory, turn right / left the power button consecu-
tively. Press the button when you find the wanted file. The unit will then play the selected file.
For instance, the file search changes in Dir01 as follows.
File01 File02 File03 File04
ö MP3 direction / file configuration
ROOT
Directory01
File01 File02 File03 File04 Dir02 Dir03 Dir04
File05 File06 Dir05 File07 File08 Dir06 File09 File10 Dir07
3-54
(4) ID3 v2 display
Η Disp button is used to change the display information.
While playing an MP3 file, you can change the file information
1 DISP shown on the LCD display.
Each time you press DISP (display), the display changes to show
75793CD82 the following.
ö If the MP3 disc does not have any ID3 information, the display will
show NO ID3 on LCD display.
Directory name / file name (normal mode)
Album name / performer / title
File number / elapsed time
(5) File scan (SCN)

Η During USB play, press SCN button to play the first 10 seconds of
each file on the whole file on the USB (SCN mark will appear on the
2 SCN LCD display).
When a desired file is reached, press the SCN button again to can-
75793CD83 cel the function.
The unit will then play the selected file.
ö In case of playing MP3 file, when the SCN (scan) button is pressed
and held for longer than 2 seconds, the SCN mark will blink on the
LCD display and all files in the selected directory will be introduced
until the file scan mode is cancelled by pressing the SCN button
again or by activating the random or repeat functions.
(6) Repeat play selector (RPT)

Η During USB play, press RPT button to play the selected file repeat-
edly (RPT will appear on the LCD display).
3 RPT Play of the file will continue to repeat until this button is pressed
again and the RPT disappears from the LCD display.
75793CD84 ö In case of playing MP3 file, when the RPT button is pressed and
held longer than 2 seconds, the RPT mark will blink on the LCD dis-
play and play all files in the selected directory and will be repeated
until the directory repeat mode is cancelled by pressing the repeat
button again or by activating the scan or random functions (RPT
mark will disappear from LCD display).
3-55
(7) Random play selector (RDM)
Η During USB play, press RDM button to play the files on the USB in a
random shuffled order (RDM will appear on the LCD display). The
4 RDM file select function will also select file in the random order instead of
the normal process.
75793CD85 The random play mode can be cancelled by this button again.
ö In case of MP3 file, when the random button is pressed and held
longer than 2 seconds, the RDM mark will blink on the LCD display
and play all files in directory randomly until the directory random
mode is cancelled by pressing the random button again or by acti-
vating the scan or repeat functions (RDM mark will disappear from
LCD display).
(8) Directory down

Η Press D- button briefly while playing MP3. The previous directory is
located each time you press this button.
5 D-
75793CD86
(9) Directory up
Η Press D+ button briefly while playing MP3 . The next directory is
located each time you press this button.
6 D+ ö If the MP3 file does not have a directory, the unit play MP3 at
10-file intervals.
75793CD87 ö If any MP3 file does not exist in USB, this button can not oper-
ate.
ÿAUX
AUX PLAYER
(1) Aux function
· Use of USB socket
Η If you want to listen to music of a external audio device, connect a
external audio device into the USB port.
Θ Press mode button to change a current mode for AUX. If audio file
AUX USB
of audio device is playing, you can listen to music through speaker.
HB1003CD63
· Use of USB /AUX cable (option)

Η If you want to listen to music of a external audio device, connect a
external audio device through USB / AUX cable.
Θ Press mode button to change a current mode for AUX. If audio file
of audio device is playing, you can listen to music through speaker.
75793CD75
3-56
4) SEAT (standard)
The seat is adjustable to fit the contours of the operator's body. It will reduce operator fatigue due
to long work hours and enhance work efficiency.
(1) Horizontal adjustment (A)

D
Η Pull lever A to adjust seat forward or backward.
Θ The seat can be moved forward and backward
over 169 mm (6.7") in 13 steps.
(2) Tilt adjustment (B)
E Pull or push lever B to adjust seat cushion upward
or downward.
(3) Adjustable Backrest
C Pull lever C to adjust seat backrest.
(4) Arm rest adjustment (E)
F This can be adjusted by turning the knob E.
A (5) Head rest adjustment (D)
This is adjustable vertically to fit operator's
B requirements, over a 75 mm (3.0") height range and
2209S3CD54
79.5˚ angle.
(6) Weight adjustment (F)
Adjust the handle to the operator's weight (50~
130 kg).
Always check the condition of the seat belt and
mounting hardware before operating the machine.
Replace the seat belt at least once every three
years, regardless of appearance.
3-57
5) SEAT (heated, option)
The seat is adjustable to fit the contours of the operator's body. It will reduce operator fatigue due
to long work hours and enhance work efficiency.
(1) Forward/Backward adjustment (A)

Η Pull lever A to adjust seat forward or backward.
Θ The seat can be moved forward and backward
over 140 mm (5.5") in 13 steps.
(2) Height/weight adjustment (B)
Η Turn the handle to adjust seat upward or down-
ward
F G · Turn to clockwise, the seat is moved to upward
B and the weight is increased.
If it is turned to counterclockwise, the seat is
moved to downward and the weight is decreased.
Handle Upward
Θ Method of changing direction (up/down)
· First, pull the handle to outside.
Downward
· Second, rotate 180˚ and release the handle.
(3) Reclining adjustment (C)
D
Pull lever C to adjust seat back rest.
(4) Arm rest adjustment (E)
This can be adjusted by pushing the button E to
right and left.
(5) Head rest adjustment (D)
E
C This is adjustable vertically to fit operator's require-
ments over 60 mm (2.4").
A
B (6) Seat cushion tilt adjustment (F)
Pull lever F to adjust seat cushion tilting angle.
21093CD55
(7) Seat cushion length adjustment (G)
Pull lever G to adjust seat cushion forward or back-
ward.
Always check the condition of the seat belt and
mounting hardware before operating the machine.
Replace the seat belt at least once every three
years, regardless of appearance.
3-58
6) FUSE & RELAY BOX
30A 20A 10A
10A 5A
30A 10A 30A

SPARE HEAD LAMP POWER ANTI- BREAKER AC COMP CLUSTER ECM
RY RY RESTART RY RY
SPARE ECM ROOM LP/
RY CASSETTE
SPARE MCU
20A 10A 20A 20A 20A 20A 20A 10A 20A 10A 20A 30A 20A 10A 30A 30A 20A 10A 10A 10A 20A 20A
LAMP(OPT)
CABIN
CONVERTER
HEAD LAMP
FUELP/P
HEATER
PRE-
SOLENOID
(BEACON)
OPTION
CIGAR
SOLENOID
SEAT
SOL
SAFETY
HEATER
AIRCON &
HORN
STOP
START,
HEATER
FUEL-
WIPER
CLUSTER
CASSETTE
PANEL
SWITCH
MCU EPPR
MCU CONT
LAMP
WORK
WORK LAMP FUEL CABIN LAMP
RY HEATER RY HORN PRE ECM
RY
30A 20A 10A

HOLDER
RY HEATER POWER START

KEY
FUSE
RY RY
AIR
CONVERT
WIPER
21093CD56
(1) The fuses protect the electrical parts and wiring from burning out.
(2) The fuse box cover indicates the capacity of each fuse and circuit it protects.
ö Replace a fuse with another of the same capacity.
Before replacing a fuse, be sure to turn OFF the starting switch.
7) MCU
(1) To match the pump absorption torque with the engine torque, MCU
LED varies EPPR valve output pressure, which control pump discharge
amount whenever feedbacked engine speed drops under the
G
Y
reference rpm of each mode set.
R
(2) Three LED lamps on the MCU display as below.
LED lamp Trouble Service

G is turned ON Normal -
21093CD57 G and R are Trouble on MCU Â Change the MCU

turned ON
G and Y are Trouble on serial Â Check if serial communication
turned ON communication line lines between controller and
cluster are disconnected
Three LED are Trouble on MCU power Â Check if the input power wire
turned OFF (24 V, GND) of controller is
disconnected
Â Check the fuse
G : green, R : red, Y : yellow
3-59
8) SERVICE METER
(1) This meter shows the total operation hours of the machine.
HOURS
(2) Always ensure the operating condition of the meter during the
machine operation. Inspect and service the machine based on
hours as indicated in chapter 6, maintenance.
21093CD59
9) RS232 service socket

(1) MCU communicates the machine data with Laptop computer
through RS232 service socket.
21093CD61
10) UPPER WINDSHIELD

Auto lock latch (1) Perform the following procedure in order to open the upper windshield.
① Pull both levers with hold both grips that are located at the top of the
windshield frame and push the windshield upward.
Grip ② Hold both grips and back into the lock position until auto lock latch is
Lever
engaged, then release the lever locked position.
21093CD62
(2) Perform the following procedure in order to close the upper windshield.
Auto lock latch
① Pull the lever of the auto lock latch in order to release the auto lock
latch.
② Reverse above step ① and ② in order to close the upper
windshield.
21093CD63
3-60
OPERATION
1. SUGGESTION FOR NEW MACHINE
1) It takes about 100 operation hours to enhance

its designed performance.
2) Operate according to below three steps and avoid
excessive operation for the initial 100 hours.
Service meter Load
Avoid excessive
Until 10 hours About 60 % operation for ini-
Until 100 hours About 80 % tial 100 hours
After 100 hours 100 %

ö Excessive operation may deteriorate the
potential performance of machine and
shorten lifetime of the machine.
3) Be careful during the initial 100 hours operation
(1) Check daily for the level and leakage of coolant,

engine oil, hydraulic oil and fuel.
(2) Check regularly the lubrication and fill grease 38094OP01A
daily all lubrication points.
(3) Tighten bolts.
(4) Warm up the machine fully before operation.
(5) Check the gauges occasionally during the
operation.
(6) Check if the machine is operating normally
during operation.
4) Replace followings after initial 50 or 250 hours
of operation
Checking items Hours

Engine oil
Engine oil filter element
50
Fuel filter
Prefilter
Hydraulic oil return filter element
Hydraulic oil tank drain filter cartridge 250
Line filter element
4-1
2. CHECK BEFORE STARTING THE ENGINE
1) Look around the machine and under the machine

to check for loosen nut or bolts, collection of dirt,
or leakage of oil, fuel or coolant and check the Check before
condition of the work equipment and hydraulic starting
system. Check also loosen wiring, and collection
of dust at places which reach high temperature.
ö Refer to the daily check on the chapter 6, mainte-
nance.
2) Adjust seat to fit the contours of the operator's
body for the pleasant operation.
38094OP02
3) Adjust the rear view mirror.
4-2
3. STARTING AND STOP THE ENGINE (CLUSTER TYPE 1)
1) CHECK INDICATOR LIGHTS
(1) Check if all the operating levers are in the

neutral position.
START
(2) Turn the starting switch to the ON position.
OFF
Buzzer sounding for 4 seconds with HYUN-
DAI logo on cluster.
ö If the ESL mode is set to the enable, enter the
password to start engine.
ö If the password has failed 5 times, please wait
30 minutes before re-attempting to enter the
password.
ö Refer to page 3-17 for ESL mode.
(3) After initialization of cluster, the operating
screen is displayed on LCD (1). 1
Also, self-diagnostic function is carried out.
21094OP04
2) STARTING ENGINE IN NORMAL TEMPERATURE

ö Sound the horn to warn the surroundings
after checking if personnel or obstacles are in Accel dial switch
the area.
(1) Turn the accel dial switch to low idle position.
Decrease
(2) Turn the starting switch to START position to
start the engine.
ö Do not hold the starting switch in the START
position for longer than 20 seconds.
The start system may be seriously damaged.
ö If the engine does not start, allow the stater
to cool for about 2 minutes before re-attempting START
to start the engine again.
ON
(3) Release the starting switch instantly after the OFF
engine starts to avoid possible damage to the
starting motor. 29094OP05
4-3
3) STARTING ENGINE IN COLD WEATHER
ö Sound horn to warn surroundings after check-
ing if there are obstacles in the area.
ö Replace the engine oil and fuel referring to
recommended oils at page 2-23.
ö Fill the anti-freeze solution to the coolant as Preheat pilot
required. lamp
OFF
ö If you turn ON the starting switch, the fuel
warmer is automatically operated to heat the
fuel by sensing the coolant temperature.
(1) Check if all the levers are in the neutral position.
Fuel warmer
(2) Turn the accel dial switch to low idle position. pilot lamp
OFF
(3) Turn the starting switch to the ON position, and
wait 1~2 minutes. More time may take according
to ambient temperature.
(4) Wait for five minutes to warm up the engine after
the preheating pilot lamp off, and than turn the
starting switch to the START position to start the START
engine.
ON
ö If the engine does not start, allow the starter OFF
to cool for about 2 minutes before attempting
(5) Release the starting switch immediately after Warming up
pilot lamp
starting engine. OFF
(6) If the temperature of the coolant is lower than

30˚C the warming up automatically starts.
ö Do not operate the working devices, or
convert the operation mode into other mode
during the warming up. 30094OP01
4-4
4) INSPECTION AFTER ENGINE START
Inspect and confirm the following after engine
starts.
(1) Is the level gauge of hydraulic oil tank in the nor-
mal level? 6 7
5 8
(2) Are there leakages of oil or water? 4 9
3
(3) Are all the warning lamps turned OFF (1-9)?
(4) Are the indicator of water temperature gauge 2
(10) and hydraulic temperature gauge (11) in the
operating range? 11
10
(5) Are the engine sound and the color of exhaust 1
gas normal?
(6) Are the sound and vibration normal?
ö Do not increase engine speed quickly after
starting, it can damage engine or turbocharg-
er.
ö If there are problems in the cluster, stop the
engine immediately and correct problems as
required. 21094OP06
5) WARMING-UP OPERATION
ö The most suitable temperature for the hydrau-
lic oil is about 50
50˚C
C (122
(122˚FF ).
It can cause serious trouble in the hydraulic
50 C
system by sudden operation when the hydraulic
oil temperature is below 2525˚CC (77
(77˚F
F ).
Then temperature must be raised to at least
25˚C
25 C (77˚F
(77 F ) before starting work.
(1) Run the engine at low idle speed for 5 minutes.
(2) Speed up the engine by accel dial and run the
engine at mid-range speed.
(3) Operate bucket lever for 5 minutes.
ö Do not operate anything except bucket lever.
(4) Run the engine at the high speed and operate
the bucket lever and arm lever for 5-10 minutes.
ö Operate only the bucket lever and arm lever.
(5) This warming-up operation will be completed by
operation of all cylinders several times, and
operation of swing and traveling. 38094OP03
4-5
6) TO STOP THE ENGINE
ö If the engine is abruptly stopped before it has
cooled down, engine life may be greatly Low idling for
shortened. Consequently, do not abruptly 5 minutes
stop the engine apart from an emergency.
ö In particular, if the engine has overheated, do
not abruptly stop it but run it at medium speed
to allow it to cool gradually, then stop it.
(1) Down the bucket on the ground then put all
the levers in the neutral position.
(2) Run the engine at low idle speed for about 5
minutes.
(3) Return the key of starting switch to the OFF
position.
(4) Remove the key to prevent other people using START
the machine and LOCK safety lever. ON
OFF
(5) Lock the cab door. 38094OP04
4-6
3. STARTING AND STOP THE ENGINE (CLUSTER TYPE 2)
1) CHECK INDICATOR LIGHTS
(1) Check if all the operating lever is on the neu-

tral position.
(2) Turn the starting switch to the ON position, START
and check following.
ON OFF
Η If all the lamps light ON and buzzer sounding
for 2 seconds.
Θ After lamp checkÖ1.00 1.00×, the version of
cluster program, is displayed onÖLCD LCD (3)
(3)×
for 5 seconds and the cluster returns to
default. 3
Ι Only below lamps will light ON and all the
other lights will turn OFF after 2 seconds.
ÂEngine oil pressure warning lamp (1)
ÂBattery charging warning lamp (2)
1
2
2209S4OP04
2) STARTING ENGINE IN NORMAL TEMPERATURE

ö Sound the horn to warn the surroundings
after checking if personnel or obstacles are in
Accel dial switch
the area.
(1) Turn the starting switch to START position to
start the engine.
ö If the engine does not start, allow the starter Decrease
(2) Release the starting switch instantly after the
engine starts to avoid possible damage to the
starting motor.
START
ON
OFF
235Z94OP05
4-7
3) STARTING ENGINE IN COLD WEATHER
ö Sound horn to warn surroundings after check-
ing if there are obstacles in the area.
ö Replace the engine oil and fuel referring to
recommended oils at page 2-23.
ö Fill the anti-freeze solution to the coolant as
Accel dial
required. switch
Decrease
ö If you turn ON the starting switch, the fuel
warmer is automatically operated to heat the
fuel by sensing the coolant temperature.
(1) Check if all the levers are in the neutral position.
Preheat pilot
lamp
(2) Turn the accel dial switch to low idle position. OFF
(3) Turn the starting switch to the ON position, and
wait 1~2 minutes. More time may take according
to ambient temperature.
(4) Wait for five minutes to warm up the engine after
the preheating pilot lamp off, and than turn the
starting switch to the START position to start the START
engine.
ON
ö If the engine does not start, allow the starter OFF
(5) Release the starting switch immediately after Warming up
pilot lamp
starting engine. OFF
(6) If the temperature of the coolant is lower than

30˚C the warming up automatically starts.
ö Do not operate the working devices, or
convert the operation mode into other mode
during the warming up. 2209S4OP05
4-8
4) INSPECTION AFTER ENGINE START
Inspect and confirm the following after engine
starts.
(1) Is the level gauge of hydraulic oil tank in the
normal level?
(2) Are there leakages of oil or water?
(3) Are all the warning lamps OFF (1-6)?
(4) Is the indicator of water temperature gauge (7)
1
and hydraulic temperature gauge (8) in the 7
8
green zone?
2 6
(5) Is the engine sound and the color of exhaust 3
gas normal?
(6) Are the sound and vibration normal?
ö Do not increase engine speed quickly after
4 5
starting, it can damage engine or
turbocharger.
ö If there are problems in the control panel,
stop the engine immediately and correct
problem as required. 3009SH4OP06
4-9
5) WARMING-UP OPERATION
ö The most suitable temperature for the hydrau-
lic oil is about 50
50˚C
C (122
(122˚FF ).
50 C
It can cause serious trouble in the hydraulic
system by sudden operation when the hydraulic
oil temperature is below 2525˚CC (77
(77˚F
F ).
Then temperature must be raised to at least
25˚C
25 C (77˚F
(77 F ) before starting work.
(1) Run the engine at low idling for 5 minutes.
(2) Speed up the idling and run the engine at
mid-range speed.
(3) Operate bucket lever for 5 minutes.
ö Do not operate anything except bucket lever.
(4) Run the engine at the high speed and operate
the bucket lever and arm lever for 5-10 minutes.
ö Operate only the bucket lever and arm lever.
(5) This warming-up operation will be completed by
operation of all cylinders several times, and
operation of swing and traveling. 2507A4OP78
ö Increase the warming-up operation during

winter.
6) TO STOP THE ENGINE

ö If the engine is abruptly stopped before it has
cooled down, engine life may be greatly Low idling for
shortened. Consequently, do not abruptly 5 minutes
stop the engine apart from an emergency.
ö In particularly if the engine has overheated,
do not abruptly stop it but run it at medium
speed to allow it to cool gradually, then stop it.
(1) Down the bucket on the ground then put all
the levers in the neutral position.
(2) Run the engine at low idling speed for about 5
minutes.
(3) Return the key of starting switch to the OFF
position.
(4) Remove the key to prevent other people using START
the machine and LOCK safety lever. ON
(5) Lock the cab door. 21074OP04
4-10
4. MODE SELECTION SYSTEM (CLUSTER TYPE 1)
1) STRUCTURE OF MECHATRONICS SYSTEM

CAPO, Computer Aided Power Optimization
6
system, is the name of mode selection system
developed by Hyundai.
ö Please refer to chapter 3, cluster for below modes
setting.
(1) Power mode
Power mode designed for various work loads
supports high performance and reduces fuel
consumption.
ÂP mode : Heavy duty power
ÂS mode : Standard power
ÂE mode : Economy power 1 2 3 4 5
(2) Work mode
One of the two work modes can be selected for 21094OP10
the optimal work condition of the machine

operation. 1 Power mode switch
① General work mode (bucket) 2 Work mode switch
When key switch is turned ON, this mode is 3 User mode switch
selected automatically. 4 Travel mode switch
5 Auto idle mode switch
② Work tool mode (breaker, crusher)
6 LCD
It controls the pump flow and system pressure
for the optimal operation of breaker or crusher.
(3) User mode

① User mode is useful for setting the user
preperable power quickly.
(engine speed, power shift and idle speed)
② There are two methods for use of user mode.
a. In operation screen
User mode switch is used to memorize the
current machine operating status and activate
the memorized user mode.
Refer to page 3-10.
b. In menu
Engine high idle rpm, auto idle rpm and pump
torque (power shift) can be modulated and
memorized separately in menu status. User mode switch
- Each memory mode has a initial set which
are mid-range of max engine speed, power
shift and auto idle speed.
21094OP11
4-11
- High idle rpm, auto idle rpm and EPPR
pressure can be adjusted and memorized in
the U-mode.
ö Refer to the page 3-12 for setting the user
mode (available on U mode only).
ÂLCD segment vs parameter setting
Step Engine Idle speed Power
( ) speed (rpm) (rpm) shift(bar)
1 1500 1000 (low idle) 0
2 1600 1050 3
3 1700 1100 6
4 1800 1150 (decel rpm) 9
5 1850 1200 12
6 1900 1250 16
7 1950 1300 20
8 2000 1350 26
9 2050 1400 32
10 2100 1450 38
21094OP12
(4) Travel mode

: Low speed traveling.
: High speed traveling.
(5) Auto idle mode
Pilot lamp ON : Auto idle function is activated.
Pilot lamp OFF : Auto idle function is canceled.
4-12
(6) Monitoring system
Information of machine performance as
monitored by the MCU can be displayed on the
LCD. Refer to the page 3-11.
Mode Monitoring Management Display Utilities
(7)
7) Self diagnostic system
MCU (Machine
achine Control
ontrol Unit)
nit)
The MCU diagnoses machine status and
FUEL TANK
problems and displays fault code in the cluster
(fault code detected by MCU is composed of
HCESPN and FMI).
※ Refer to the page 3-11 for LCD display. MCU
(8) Anti-restart system

(8
The system protects the starter from inadvertent
restarting after the engine is already operational. 3009SH4OP03
2) HOW TO OPERATE MODE SELECTION SYSTEM

(1) When start key switch is turned ON
Η When start key switch is turned on, the cluster
turns on and buzzer sounds for 4 seconds. And
START
then main information as gauges and engine
OFF
speed are displayed on LCD.
Θ Initial default mode settings are dispalyed in the
cluster.
Mode Status
Power mode E ON
Work mode ON
Travel mode Low ( ) ON
Auto idle ON
ö These setting can be changed at U mode.

Ι Self-diagnostic function can be carried out from Work mode Auto idle
this point. Power mode Travel mode
21094OP14
4-13
(2) After engine start
Η When the engine is started, rpm display
indicates low idle, 1000Ü100 rpm.
Θ If coolant temperature is below 30˚C, the warm-
ing up pilot lamp lights ON and after 4 seconds START
the engine speed increases to 1150Ü100 rpm
ON OFF
automatically to warm up the machine.
· After 2-3 minutes, you can select any mode
depending on job requirement.
Warming up pilot lamp

RPM display
21094OP15
3) SELECTION OF POWER MODE

(1) E mode
The accel dial is set 10 and the auto idle mode is
canceled. E mode pilot lamp
Power mode switch
Engine rpm Effect
Variable power control

in proportion to lever stroke
1900 Ü 50 (improvement in fuel efficiency)
ö Same power as S mode in full 21094OP16
lever operation.
ö When the accel dial is located below 9 the
engine speed decreases about 50~100 rpm per
dial set.
(2) S mode
canceled. S mode pilot lamp
Engine rpm Effect Power mode switch
2000 Ü 50 Standard power

21094OP17
dial set.
4-14
(3) P mode
canceled.
Engine rpm Effect P mode pilot lamp
Power mode switch

Approximately 120 % of
2100 Ü 50 power and speed available
than S mode.

engine speed decreases about 50~100 rpm per 21094OP18
dial set.
4-15
4. MODE SELECTION SYSTEM (CLUSTER TYPE 2)
1) STRUCTURE OF CAPO SYSTEM

CAPO, Computer Aided Power Optimization
system, is the name of mode selection system
developed by Hyundai. 6
(1) Work mode

3 work modes can be selected for the optimal
work speed of the machine operation.
Η Heavy duty work mode
The heavy duty work solenoid is deactivated to
make the arm operation speed faster. 1 2
Θ General work mode
5
When key switch is turned ON, this mode is 3
selected automatically and swing operation
speed is faster than heavy duty work mode. 4
(2) Power mode

2209S4OP07
Power mode designed for various work loads
maintains high performance and reduces fuel
1 Work mode
consumption. 2 Power mode
ÂH mode : High power
3 User mode
ÂS mode : Standard power 4 Auto decel mode
(3) User mode 5 Travel mode
ÂM : Maximum power 6 LCD
ÂU : You can change the engine and pump
power and memorize it for your pre-
ference
How to modulate the memory set

Η Each memory mode has a initial set which are
mid-range of max engine speed, auto decel
rpm, and EPPR valve input current.
ACCEL
DECEL
EPPR
2507A4OP08
4-16
Θ High idle rpm, auto decel rpm, EPPR pressure
can be modulated and memorized separately SYSTEM MENU
in the U-mode.
ö Refer to the page 3-29 for set of user mode. Monitoring Diagnosis Management
ÂLCD
LCD segment vs parameter setting Settings Display User Mode
User mode icon

Step ACCEL Idle speed Power shift
( ) (rpm) (rpm) (mA)
1 1500 Low idle (1000) 150
ACCEL
2 1600 1050 200
DECEL
3 1700 1100 250 EPPR
4 1800 Decel rpm (1150) 300

5 1850 1200 350
6 1900 1250 400
7 1950 1300 450
8 2000 1350 500
9 2050 1400 550
10 2100 1450 600
(4) Auto decel mode

Engine quick deceleration.
(5) Travel mode
: Low speed traveling.
: High speed traveling.
3009SH4OP05
4-17
(6) Monitoring system
Information of machine performance as
monitored by the MCU controller can be LCD
displayed on the LCD
LCD. Refer to the page 3-26.
(7) Self diagnostic system SYSTEM MENU
MCU controller Monitoring Diagnosis Management
The MCU controller diagnoses problems in Settings Display User Mode
the CAPO system caused by electric parts'

malfunction and by open or short circuit,
which are displayed on the LCD as error
FUEL TANK
codes(2 digit).
ö Consult hyundai or huyndai dealer for
details.
MCU
ö Refer to the page 3-26 for LCD display.
(8) Anti-restart system
(8
The system protects the star ter from
inadvertent restarting after the engine is
already operational. 3009SH4OP01
2) HOW TO OPERATE MODE SELECTION

SYSTEM LCD
(1) When start key is turned ON

Η When start key is turned ON, all illumination
lamps are ON and all lamps are OFF
automatically after 5 seconds. But a battery
charging warning lamp and an engine oil
pressure warning lamp keep turned ON until
engine starting.
Θ After lamp checkÖ1.001.00×, the version of
cluster program, is displayed on LCD for 2
seconds.
Ι After the version of program is displayed, the
cluster returns to default. Exactly engine
rpm, battery charging warning lamp and
engine oil pressure warning lamp are turned
ON and S mode, auto decel, low travel
speed (Turtle mark) are displayed.
Κ In default condition self-diagnostic function
including trouble detecting of electric system
can be carried out. 3009SH4OP07
4-18
(2) After engine start
Η When the engine is started, three lamps are ON
as below.
Mode Status
Power mode ON
Work mode S ON
Travel mode Low ( ) ON
Auto decel mode ON
Â In this condition, tachometer indicates low

idle, 1000Ü100 rpm.
Â If coolant temperature is below 30˚C, after 10
seconds the engine speed increases to
1150Ü100 rpm automatically to warm up the
machine.
Â After 2-3 minutes, you can select any mode
depending on job requirement.
Θ Self-diagnostic function can be carried out the
same as start key is ON.
3009SH4OP08
3) SELECTION OF POWER MODE

(1) S mode
When the accel dial is at setting 10 and auto
decel mode is cancelled and S mode is selected.
Engine rpm Effect
Same power as non mode type
1900 Ü 50
machine.
engine speed decreases about 50~100 rpm per 21073CD23A
dial set.
(2) H mode
decel mode is cancelled and H mode is
selected.
Engine rpm Effect
Approximately 110% of power
2000 Ü 50 and speed available than non
mode type machine or S mode.
ö When the accel dial is located below 9 the 21073CD23B
dial set.
4-19
(3) M mode
decel mode is cancelled and H mode is
selected.
Engine rpm Effect
Approximately 130% of power
2100 Ü 50 and speed available than non
mode type machine or S mode.
ö When the accel dial is located below 9 the 17W73CD21
dial set.
4-20
5. OPERATION OF THE WORKING
ORKING DEVICE
ö Confirm the operation of control lever and

working device.
1) Left control lever controls arm and swing.
2) Right control lever controls boom and bucket. 7 6
3) When you release the control lever, control 5 8
lever returns to neutral position automatically.

32
1 4
ö When operating swing, consider the swing
distance by inertia.
3009SH4OP02
ö Left control lever

1 Arm roll-out
3
2 Arm roll-in 1
3 Swing right 4
4 Swing left
2
38094OP07
ö Right control lever

5 Boom lower 6
6 Boom raise
7 Bucket roll-out 7
8 Bucket roll-in
5
8
38094OP08
4-21
6. TRAVELING OF THE MACHINE
1) BASIC OPERATION
(1) Traveling position Traveling position
It is the position which the traveling motor is in
the rear and the working device is forward.
Be careful as the traveling direction will be
reversed when the whole machine is swinged
180 degree.
(2) Traveling operation
It is possible to travel by either travel lever or
pedal.
ö Do not travel continuously for a long time. Travel motor
ö Reduce the engine speed and travel at a low
38094OP06
speed when traveling on uneven ground.
(3) Forward and backward traveling

When the left and right travel lever or pedal are
pushed at the same time, the machine will travel
forward or backward.
ö The speed can be controlled by the operation
stroke of lever or pedal and change of
direction will be controlled by difference of the
left and right stroke.
21094OP24
(4) Pivot turning

Operating only one side of lever or pedal make
the change of direction possible by moving
only one track.
21094OP25
(5) Counter rotation

It is to change the direction at the original place
by moving the right and left track. Both side of
lever or pedal are operated to the other way at
the same time.
21094OP26
4-22
2) TRAVELING ON A SLOPE
(1) Make sure that the travel lever is properly
maneuvered by confirming the travel motor is in
the right location.
(2) Lower the bucket 20 to 30 cm (1 ft) to the ground
so that it can be used as a brake in an
emergency. 20~
30c
m(1
(3) If the machine starts to slide or loses stability, ft)
lower the bucket immediately and brake the
machine.
Travel motor
(4) When parking on a slope, use the bucket as a
brake and place blocks behind the tracks to
prevent sliding.
ö Machine cannot travel effectively on a slope
when the oil temperature is low. Do the
warming-up operation when it is going to
travel on a slope.
Be careful when working on slopes. It may Travel motor
cause the machine to lose its balance and
turn over. 20~30cm(1ft)
Be sure to keep the travel speed switch on
the LOW (turtle mark) while traveling on a
38094OP05
slope.
3) TRAVELING ON SOFT GROUND

ö If possible, avoid to operate on soft ground.
(1) Move forward as far as machine can move.
(2) Take care not to go beyond the depth where 90 ~ 110
towing is impossible on soft ground.
(3) When driving becomes impossible, lower bucket
and use boom and arm to pull the machine.
Operate boom, arm, and travel lever at the same
38094OP09
time to avoid the machine sinking.
4-23
4) TOWING THE MACHINE
Tow the machine as follows when it can not move
on it's own.
(1) Tow the machine by other machine after hook
the wire rope to the frame as shown in picture at
right.
(2) Hook the wire rope to the frame and put a
support under each part of wire rope to prevent
damage.
ö Never tow the machine using only the tie
hole, because this may break.
Make sure no personnel are standing close to
the tow rope.
21074OP14A
4-24
7. EFFICIENT WORKING METHOD
1) Do the digging work by arm.

Use the pulling force of arm for digging and use
together with the digging force of the bucket if
necessary.
38094OP10
2) When lowering and raising the boom operate Operate softy for the begining and the end
softly for the beginning and the end.
In particularly, sudden stops while lowering the
boom may cause damage to the machine.
38094OP11
3) The digging resistance and wearing of tooth can

be reduced by putting the end of bucket tooth to
the digging direction.
13034OP39
4) Set the tracks parallel to the line of the ditch to be

excavated when digging ditch. Do not swing while
digging.
Parallel
21074OP17
4-25
5) Dig slowly with keeping the angle of boom and
arm, 90-110 degree when maximum digging force
is required.
90~110
38094OP12
6) Operate leaving a small safety margin of cylinder Margin

stroke to prevent damage of cylinder when
working with the machine.
38094OP13
7) Keep the bucket to the dumping position and the

arm horizontal when dumping the soil from the
bucket.
Operate bucket lever 2 or 3 times when hard to
dump.
ö Do not use the impact of bucket tooth when
dumping.
38094OP14
8) Operate stop of swing considering the swing slip

distance is created by inertia after neutralizing the
swing lever.
Inertia
Swing stop
21074OP21
4-26
9) If the excavation is in an underground location or Incorrect
in a building, make sure that there is adequate
overhead clearance and that there is adequate
ventilation.
38094OP24
10) Do not use the dropping force of the work Incorrect

equipment for digging.
The machine can be damaged by the impact.
38094OP15
11) Do not use the bucket to crack hard objects like Incorrect
concrete or rocks.
This may break a tooth or pin, or bend boom.
38094OP16
12) NEVER CARRY OUT EXCESSIVE OPERATIONS Incorrect

Operation exceeding machine performance may
result in accident or failure.
Carry out lifting operation within specified load
limit.
Never carry out operations which may damage
the machine such as overload or over-impact-
load.
Never travel while carrying a load.
38094OP25
In case you need installing over load warning
device for object handling procedure, please
contact Hyundai distributor.
4-27
13) BUCKET WITH HOOK
When carrying out lifting work, the special lifting
hook is necessary.
The following operations are prohibited.
Hook
ÂLifting loads with a wire rope fitted around the
bucket teeth.
ÂLifting loads with the wire rope wrapped directly
around the boom or arm.
When performing lifting operation, securely hook
the wire rope onto the special lifting hook.
When performing lifting operation, never raise or
lower a person.
Due to the possible danger of the load falling or of
collision with the load, no persons shall be
allowed in the working area.
Before performing lifting operation, designate an
operation supervisor.
Always execute operation according to his
instructions.
ÂExecute operating methods and procedures
under his direction.
ÂSelect a person responsible for signaling.
Operate only on signals given by such person.
21074OP24
Never leave the operator's seat while lifting a load.
4-28
8. OPERATION IN THE SPECIAL WORK SITES
1) OPERATION THE MACHINE IN A COLD WEATHER

(1) Use proper engine oil and fuel for the weather.
(2) Fill the required amount of antifreeze in the
coolant.
50 C
(3) Refer to the starting engine in cold weather.
Start the engine and extend the warming up
operation.
(4) Be sure to open the heater cock when using the
heater.
(5) Always keep the battery completely charged.
ö Discharged batteries will freeze more easily
than fully charged.
38094OP17
(6) Clean the machine and park on the wood plates.
2) OPERATION IN SANDY OR DUSTY WORK SITES
(1) Inspect air cleaner element frequently. Clean or

replace element more frequently, if warning
lamp comes ON and buzzer sounds
simultaneously, regardless of inspection period.
ö Replace the inner and outer element after 6
times of cleaning.
(2) Inspect radiator frequently, and keep cooling fins
clean.
(3) Prevent sand or dust from getting into fuel tank
and hydraulic tank during refilling.
(4) Prevent sand or dust from penetrating into
hydraulic circuit by tightly closing breather cap of
hydraulic oil tank. Replace hydraulic oil filter and
air breather element frequently.
(5) Keep all lubricated part, such as pins and
bushings, clean at all times.
(6) If the air conditioner and heater filters clogged,
the heating or cooling capacity will drop. Clean
or replace the filter element more frequently.
4-29
3) SEA SHORE OPERATION
(1) Prevent ingress of salt by securely tightening
plugs, cocks and bolts of each part.
(2) Wash machine after operation to remove salt
residue.
Pay special attention to electrical parts, and
hydraulic cylinders and track tension cylinder to
prevent corrosion.
(3) Inspection and lubrication must be carried out
more frequently.
Supply sufficient grease to replace all old grease
in bearings which have been submerged in
water for a long time.
4) OPERATION IN MUD, WATER OR RAIN

WORK SITES
(1) Perform a walk around inspection to check for
any loose fittings, obvious damage to the
machine or any fluid leakage.
(2) After completing operations, clean mud, rocks or
debris from the machine. Inspect for damage,
cracked welds or loosened parts.
(3) Perform all daily lubrication and service.
(4) If the operations were in salt water or other
corrosive materials, make sure to flush the
affected equipment with fresh water.
4-30
9. NORMAL OPERATION OF EXCAVATOR
Followings may occur during operation due to the

nature of a hydraulic excavator.
1) When rolling in the arm, the roll-in movement stop

momentary at point X in the picture shown, then
recovers speed again after passing point X.
The reason for this phenomenon is that move-
ment by the arm weight is faster than the speed of
oil flow into the cylinder.
2) When lowering the boom, one may hear continu- X
ous sound.
This is caused by oil flow in the valve.
3) Overloaded movement will produce sound
caused by the relief valves, which are for the
protection of the hydraulic systems.
4) When the machine is started swing or stopped, a
noise near the swing motor may be heard. The
38094OP18
noise is generated when the brake valve relieves.
4-31
10. ATTACHMENT LOWERING (when engine is stopped)
1) On machines equipped with an accumulator, for a

short time (within 1 minute) after the engine is
stopped, the attachment will lower under its own
weight when the attachment control lever is
shifted to LOWER. That is happen only starting
switch ON position and safety lever UNLOCK
position. After the engine is stopped, set the
safety lever to the LOCK position.
Be sure no one is under or near the
attachment before lowering the boom.
2) The accumulator is filled with high-pressure
nitrogen gas, and it is extremely dangerous if it is
handled in the wrong way. Always observe the
following precautions.
Never make any hole in the accumulator
expose it to flame or fire.
Do not weld anything to the accumulator.
ö W h e n c a r r y i n g o u t d i s a s s e m bl y o r Accumulator
maintenance of the accumulator, or when

disposing of the accumulator, it is necessary to
release the gas from the accumulator. A
special air bleed valve is necessary for this
operation, so please contact your Hyundai
21094OP40
distributor.
4-32
11. STORAGE
Maintain the machine taking care of following to

prevent the deterioration of machine when storing
the machine for a long time, over 1 month.
1) CLEANING THE MACHINE
Clean the machine. Check and adjust tracks. 4 3 1
Grease each lubrication part.
2) LUBRICATION POSITION OF EACH PART
Change all oil.
ö Be particularly careful when you reuse the 5 2 6
machine.
As oil can be diluted during storage.
Apply an anticorrosive lubricant on the exposed 1 Lubricating manifold (5EA)
part of piston rod of cylinder and in places 2 Boom cylinder pin (2EA)
where the machine rusts easily. 3 Boom and arm connection pin (1EA)
4 Arm cylinder pin (rod side, 1EA)
5 Arm and bucket (6EA)
6 Boom rear bearing center (1EA)
38094OP19
3) MASTER SWITCH
Turn OFF the master switch mounted electric box
and store the machine. Master switch
4) Be sure to mix anticorrosive antifreezing solution
in the radiator.
DISCONNECT SWITCH
29094OP03
5) PREVENTION OF DUST AND MOISTURE

Keep machine dry. Store the machine setting
wood on the ground.
ö Cover exposed part of piston rod of cylinder.
ö Lower the bucket to the ground and set a sup-
port under track.
38094OP20
4-33
6) DURING STORAGE
Start engine and move the machine and work
equipment once a month and apply lubrication to
Avoid excessive
each part. operation for ini-
tial 100 hours
ö Check the level of engine oil and coolant and
fill if required when starting engine.
ö Clean the anticorrosive on the piston rod of cyl-
inder.
ö Operate the machine such as traveling, swing
and work equipment operation to make sure
enough lubrication of all functional compo-
nents.
38094OP01A
4-34
12. RCV LEVER OPERATING PATTERN
1) PATTERN CHANGE VALVE NOT INSTALL (standard)
C Type Terminal A
B
block H
G
2 90 (Lever only) E
D
J
öWhenever
Whenever a change is made
F
to the machine control pat-
Nut(22) tern also exchange the pat-
Mounting tern label in the cab to
R
H
bolt(41)
LH
match the new pattern.
LH
T
1 3 1
P
4 3 4
P 2
2 T
1
38094OP22
Operation Hose connection (port)

Pattern Control function RCV Change of Terminal block
Left RCV lever Right RCV lever
lever From To
ISO Type 1Arm out Θ D -
1 5
2Arm in Κ E -
Left
3Swing right Ι B -
4 3 8 7
4Swing left Η A -
5Boom lower Κ J -
6Boom raise Θ H -
Right
7Bucket out Η G -
2 6
Hyundai 8Bucket in Ι F -
1Boom lower Θ D J
A Type 1 5
2Boom raise Κ E H
Left
3Swing right Ι B -
4 3 8 7 4Swing left Η A -
5Arm out Κ J D
6Arm in Θ H E
Right
7Bucket out Η G -
2 6
8Bucket in Ι F -
B Type
1Boom lower Θ D J
1 5 2Boom raise Κ E H
Left
3Bucket in Ι B F
4 3 8 7
4Bucket out Η A G
5Arm out Κ J D
6Arm in Θ H E
Right
7Swing right Η G B
2 6
8Swing left Ι F A
C Type Η Loosen the RCV lever mounting bolt (41) and rotates
1 5
lever assy 90˚ counterclockwise; then install.
Left
Θ To put lever in correct position, disassemble nut (22)
4 3 8 7
and rotates only lever 90˚ clockwise.
Right Same as ISO type

2 6
4-35
13. SWITCHING HYDRAULIC ATTACHMENT CIRCUIT
1) The combined hydraulic attachment circuit is

capable of providing single action or double action.
2) The position of 3 way valve selects the single
action hydraulic attachment circuit or the double
action hydraulic attachment circuit.
3) Before you change the flow mode of hydraulic

attachment circuit, place the machine in the
servicing position as shown. Stop the engine.
38094OP21
4) Use the spanner to turn the bolt of 3 way valve.

Make sure that you turn the bolt between ; and Groove
Bolt b
Ϳ.
(1) One way flow (hydraulic breaker) c
Position the groove parallel to the piping (;).
FRONT
(2) Two way flow (clamshell or shear)
Position the groove perpendicular to the piping
(Ϳ).
21094OP36
4-36
TRANSPORTATION
1. PREPARATION FOR TRANSPORTATION
1) When transporting the machine, observe the

various road rules, road transportation vehicle
laws and vehicle limit ordinances, etc.
2) Select proper trailer after confirming the weight
and dimension from the chapter 2, specification.
3) Check the whole route such as the road width, the
height of bridge and limit of weight and etc., which
will be passed.
4) Get the permission from the related authority if
necessary.
5) Prepare suitable capacity of trailer to support the
21095TA01
machine.
6) Prepare gangplank for safe loading referring to

the below table and illustration.
A B Loading plate
of trailer B
1.0 3.65 ~ 3.85
Gan
1.1 4.00 ~ 4.25 gpla
A nk
1.2 4.35 ~ 4.60
Block 15 ~ 16Á
1.3 4.75 ~ 5.00
1.4 5.10 ~ 5.40
1.5 5.50 ~ 5.75 13035TA02
5-1
2. DIMENSION AND WEIGHT
1) R330LC-9S
(1) Base machine
Mark Description Unit Specification
L Length mm (ft-in) 5730 (18' 10")
H
H Height mm (ft-in) 3090 (10' 2")
W Width mm (ft-in) 3280 (10' 9")
Wt Weight kg (lb) 26700 (58860) L W
ö With 600 mm (24") triple grouser shoes and 6200 kg

(13670 lb) counterweight. 29095TA02
(2) Boom assembly

L Length mm (ft-in) 6670 (21' 11")
H
H Height mm (ft-in) 1720 ( 5' 8")
W Width mm (ft-in) 785 ( 2' 7")
L
Wt Weight kg (lb) 3040 (6700)
ö 6.45 m (21' 2") boom with arm cylinder (included
piping and pins). 13035TA03
(3) Arm assembly

L Length mm (ft-in) 4340 (14' 3")
H
H Height mm (ft-in) 955 ( 3' 2")

W Width mm (ft-in) 435 ( 1' 5") L

ö 3.2 m (10' 6") arm with bucket cylinder (included
linkage and pins). 13035TA04
(4) Bucket assembly

L Length mm (ft-in) 1840 ( 6' 0")
H
H Height mm (ft-in) 1120 ( 3' 8")

W Width mm (ft-in) 1535 ( 5' 0") L
ö 1.44 m3 (1.88 yd3) SAE heaped bucket (included tooth
and side cutters). 13035TA05
5-2
(5) Boom cylinder
L Length mm (ft-in) 2305 ( 7' 7")
H
H Height mm (ft-in) 276 ( 0' 11")
W Width mm (ft-in) 420 ( 1' 5") L
ö Included piping.
13035TA06
(6) Cab assembly

L Length mm (ft-in) 1962 ( 6' 4")
H
H Height mm (ft-in) 1686 ( 5' 6")
W Width mm (ft-in) 1000 ( 3' 3")
21095TA03
(7) Counterweight
L Length mm (ft-in) 2980 ( 9' 9")
H
H Height mm (ft-in) 1050 ( 3' 11")

W Width mm (ft-in) 590 (1' 11")
L W
2507A5TR05
5-3
2) R330NLC-9S
(1) Base machine
L Length mm (ft-in) 5730 (18' 10")
H
H Height mm (ft-in) 3090 (10' 2")
W Width mm (ft-in) 2990 ( 9' 10")

(13670 lb) counterweight.
29095TA02

(1) Base machine
L Length mm (ft-in) 5730 (18' 10")
H
H Height mm (ft-in) 3390 (11' 1")
W Width mm (ft-in) 3470 (11' 5")

(14550 lb) counterweight. 29095TA03
5-4
3. LOADING THE MACHINE
1) Load and unload the machine on a flat ground.

2) Use the gangplank with sufficient length, width,
thickness and gradient.
3) Place the swing lock lever to the LOCK position
before fixing the machine at the bed of trailer and
confirm if the machine parallels the bed of trailer.
Keep the travel motor in the rear when loading
and in the front when unloading.
38095TR02
4) Do the following after loading the machine to the

trailer.
(1) Stop loading when the machine is located
horizontally with the rear wheel of trailer.
38095TR03
(2) Place the swing lock lever to the LOCK position

after the swing the machine 180degree.
38095TR04
5-5
(3) Lower the working equipment gently after the
location is determined.
ö Place rectangular timber under the bucket
cylinder to prevent the damage of it during
transportation.
Be sure to keep the travel speed switch on
the LOW (turtle mark) while loading and
unloading the machine.
Avoid using the working equipment for
loading and unloading since it will be very
dangerous.
Do not operate any other device when
loading.
Be careful on the boundary place of loading
plate or trailer as the balance of machine will
abruptly be changed on the point.
38095TR05
The machine with long reach attachments

should be moved or transmitted with boom and
arm fixed using stay.
Stay
29075TA03
5) Fix method of stay bracket 5~7mm

5~7mm
(1) Extend arm cylinder to maximum.
(2) Mark on the rod of 5~7 mm distance from tube
end. Stay
(3) Retract the arm cylinder to the mark.
(4) Adjust the stay bracket and than fix the stay to
the proper location.
Stay bracket
29075TA04
5-6
4. FIXING THE MACHINE
1) Lower down the working device on the loading

Starting switch
plate of trailer.
2) Keep the safety lever on the LOCK position.
3) Turn OFF all the switches and remove the key.
Safety lever
3009SH5TA01
4) Secure all locks.

Tool box & fuel tank
Engine hood
Cab Side cover
3309S5TA02
5) Place timber underneath of the track and fix firmly

with wire rope to prevent the machine from
moving forward, backward, right or left.
Chain
38095TR06
5-7
5. LOADING AND UNLOADING BY CRANE
1) Check the weight, length, width and height of the

machine referring to the chapter 2, specification
when you are going to hoist the machine. Wire rope
Stay
2) Use long wire rope and stay to keep the distance
with the machine as it should avoid touching with
the machine.
3) Put a rubber plate contact with wire rope and 0.5~1.0m
machine to prevent damage.
Between track roller Between track
4) Place crane on the proper place. No.1 and No.2 roller and sprocket
5) Install the wire rope and stay like the illustration.

Make sure wire rope is proper size. Wire rope
Stay
Place the safety lever to LOCK position to
prevent the machine moving when hoisting the
machine.
The wrong hoisting method or installation of
wire rope can cause damage to the machine.
REAR VIEW
Do not load abruptly.
38095TR07
Keep area clear of personnel.
5-8
MAINTENANCE
1. INSTRUCTION
1) INTERVAL OF MAINTENANCE
(1) You may inspect and service the machine by

the period as described at page 6-11 based on
hour meter at control panel.
(2) Shorten the interval of inspect and service
depending on site condition. (such as dusty
area, quarry, sea shore and etc.) 22
22
2
Service
(3) Practice the entire related details at the same meter
time when the service interval is doubled.
For example, in case of 100hours, carry out all
the maintenanceÖEach 100hours, each 50
hours and daily service×at the same time.
3009SH6MA01
2) PRECAUTION
(1) Start to maintenance after you have the full
knowledge of machine.
(2) The monitor installed on this machine does not
entirely guarantee the condition of the machine.
Daily inspection should be performed according
to clause 4, maintenance check list.
(3) Engine and hydraulic components have been
preset in the factory.
Do not allow unauthorized personnel to reset
them.
(4) Ask to your local dealer or Hyundai for the
maintenance advice if unknown.
(5) Drain the used oil and coolant in a container
and handle according to the method of handling
for industrial waste to meet with regulations of
each province or country.
6-1
3) PROPER MAINTENANCE
(1) Replace and repair of parts
It is required to replace the wearable and
consumable parts such as bucket tooth, side
cutter, filter and etc., regularly.
Replace damaged or worn parts at proper time
to keep the performance of machine.
(2) Use genuine parts.
(3) Use the recommended oil.
(4) Remove the dust or water around the inlet of oil
tank before supplying oil.
(5) Drain oil when the temperature of oil is warm.
(6) Do not repair anything while operating the
engine.
Stop the engine when you fill the oil.
(7) Relieve hydraulic system of the pressure before
repairing the hydraulic system.
(8) Confirm if the cluster is in the normal condition
after completion of service.
(9) For more detail information of maintenance,
please contact local Hyundai dealer.
ö Be sure to start the maintenance after fully
understand the chapter 1, safety hints.
6-2
4) RELIEVING THE PRESSURE IN THE HYDRAULIC SYSTEM
ö Spouting of oil can cause the accident when
loosening the cap or hose right after the oper-
ating of machine as the machine or oil is on
the high pressure on the condition.
Be sure to relieve the pressure in the system
before repairing hydraulic system.
(1) Place machine in parking position, and stop the
engine.
38096MA03
(2) Set the safety lever completely in the release

position, operate the control levers and pedals Lever Pedal
fully to the front, rear, left and right, to release
the pressure in the hydraulic circuit.
ö This does not completely release the pressure,
so when serving hydraulic component, loosen
the connections slowly and do not stand in the
direction where the oil spurt out.
21096MA03
(3) Loosen the cap and relieve the pressure in the

tank by pushing the top of the air breather.
Air breather
3309SH6MA02
6-3
5) PRECAUTION WHEN INSTALLING HYDRAULIC HOSES OR PIPES
(1) Be particularly careful that the joint of hose, pipe
and functioning item are not damaged.
Avoid contamination.
(2) Assemble after cleaning the hose, pipe and joint
of functioning item.
(3) Use genuine parts.
(4) Do not assemble the hose in the condition of
twisted or sharp radius.
(5) Keep the specified tighten torque.
6-4
6) PERIODICAL REPLACEMENT OF SAFETY PARTS
(1) It is desirable to do periodic maintenance the
machine for using the machine safely for a long
time.
However, recommend to replace regularly the
parts related safety not only safety but maintain
satisfied performance.
(2) These parts can cause the disaster of life and
material as the quality changes by passing time
and it is worn, diluted, and gets fatigued by
using repeatedly.
These are the parts which the operator can not
judge the remained lifetime of them by visual
inspection.
(3) Repair or replace if an abnormality of these
parts is found even before the recommended
replacement interval.
Periodical replacement of safety parts Interval
Fuel hose (tank-engine)

Every
Engine Heater hose 2 years
(heater-engine)
Pump suction hose

Main Pump delivery hose Every
circuit 2 years
Hydraulic Swing hose
system Boom cylinder line hose
Working Every
Arm cylinder line hose
device 2 years
Bucket cylinder line hose
ö1.
1. Replace O-ring and gasket at the same
time when replacing the hose.
2.
2. Replace clamp at the same time if the
hose clamp is cracked when checking
and replacing the hose.
6-5
2. TIGHTENING TORQUE
Use following table for unspecified torque.
1) BOLT AND NUT
(1) Coarse thread

8T 10T
Bolt size
kgfÂm lbfÂft kgfÂm lbfÂft
M 6Ý1.0 0.9 ~ 1.3 6.5 ~ 9.4 1.1 ~ 1.7 8.0 ~ 12.3
M 8Ý1.25 2.0 ~ 3.0 14.5 ~ 21.7 2.7 ~ 4.1 19.5 ~ 29.7
M10Ý1.5 4.0 ~ 6.0 28.9 ~ 43.4 5.5 ~ 8.3 39.8 ~ 60.0
M12Ý1.75 7.4 ~ 11.2 53.5 ~ 81.0 9.8 ~ 15.8 70.9 ~ 114
M14Ý2.0 12.2 ~ 16.6 88.2 ~ 120 16.7 ~ 22.5 121 ~ 163
M16Ý2.0 18.6 ~ 25.2 135 ~ 182 25.2 ~ 34.2 182 ~ 247
M18Ý2.5 25.8 ~ 35.0 187 ~ 253 35.1 ~ 47.5 254 ~ 344
M20Ý2.5 36.2 ~ 49.0 262 ~ 354 49.2 ~ 66.6 356 ~ 482
M22Ý2.5 48.3 ~ 63.3 349 ~ 458 65.8 ~ 98.0 476 ~ 709
M24Ý3.0 62.5 ~ 84.5 452 ~ 611 85.0 ~ 115 615 ~ 832
M30Ý3.5 124 ~ 168 898 ~ 1214 169 ~ 229 1223 ~ 1656
M36Ý4.0 174 ~ 236 1261 ~ 1704 250 ~ 310 1808 ~ 2242
(2) Fine thread

8T 10T
Bolt size
kgfÂm lbfÂft kgfÂm lbfÂft
M 8Ý1.0 2.2 ~ 3.4 15.9 ~ 24.6 3.0 ~ 4.4 21.7 ~ 31.8
M10Ý1.25 4.5 ~ 6.7 32.5 ~ 48.5 5.9 ~ 8.9 42.7 ~ 64.4
M12Ý1.25 7.8 ~ 11.6 56.4 ~ 83.9 10.6 ~ 16.0 76.7 ~ 116
M14Ý1.5 13.3 ~ 18.1 96.2 ~ 131 17.9 ~ 24.1 130 ~ 174
M16Ý1.5 19.9 ~ 26.9 144 ~ 195 26.6 ~ 36.0 192 ~ 260
M18Ý1.5 28.6 ~ 43.6 207 ~ 315 38.4 ~ 52.0 278 ~ 376
M20Ý1.5 40.0 ~ 54.0 289 ~ 391 53.4 ~ 72.2 386 ~ 522
M22Ý1.5 52.7 ~ 71.3 381 ~ 516 70.7 ~ 95.7 511 ~ 692
M24Ý2.0 67.9 ~ 91.9 491 ~ 665 90.9 ~ 123 658 ~ 890
M30Ý2.0 137 ~ 185 990 ~ 1339 182 ~ 248 1314 ~ 1796
M36Ý3.0 192 ~ 260 1390 ~ 1880 262 ~ 354 1894 ~ 2562
6-6
2) PIPE AND HOSE (FLARE type)
Thread size (PF) Width across flat (mm) kgfÂm lbfÂft
1/4" 19 4 28.9
3/8" 22 5 36.2
1/2" 27 9.5 68.7
3/4" 36 18 130.2
1" 41 21 151.9
1-1/4" 50 35 253.2
3) PIPE AND HOSE (ORFS type)

Thread size (UNF) Width across flat (mm) kgfÂm lbfÂft
9/16-18 19 4 28.9
11/16-16 22 5 36.2
13/16-16 27 9.5 68.7
1-3/16-12 36 18 130.2
1-7/16-12 41 21 151.9
1-11/16-12 50 35 253.2
4) FITTING
Thread size Width across flat (mm) kgfÂm lbfÂft
1/4" 19 4 28.9
3/8" 22 5 36.2
1/2" 27 9.5 68.7
3/4" 36 18 130.2
1" 41 21 151.9
1-1/4" 50 35 253.2
6-7
4) TIGHTENING TORQUE OF MAJOR COMPONENT
Torque
No. Descriptions Bolt size
kgfÂm lbfÂft
1 Engine mounting bolt (engine-bracket) M12 Ý 1.75 10 Ü 1.0 72.3 Ü 7.2
2 Engine mounting bolt (bracket-frame) M24 Ý 3.0 90 Ü 7.0 651 Ü 51
3 Engine Radiator mounting bolt M16 Ý 2.0 29.7 Ü 4.5 215 Ü 32.5
4 Coupling mounting socket bolt M20 Ý 2.5 46.5 Ü2.5 336 Ü18.1
5 Fuel tank mounting bolt M20 Ý 2.5 57.9 Ü 8.7 419 Ü 62.9
6 Main pump housing mounting bolt M10 Ý 1.5 6.9 Ü 0.3 49.9 Ü 2.2
7 Main pump mounting socket bolt M20 Ý 2.5 42 Ü 4.5 304 Ü 32.5
Hydraulic
8 Main control valve mounting nut M12 Ý 1.75 12.3 Ü 1.3 89.0 Ü 9.4
system
9 Hydraulic oil tank mounting bolt M20 Ý 2.5 57.9 Ü 8.7 419 Ü 62.9
10 Turning joint mounting bolt, nut M12 Ý 1.75 12.3 Ü 1.3 89.0 Ü 9.4
11 Swing motor mounting bolt M20 Ý 2.5 57.9 Ü 8.7 419 Ü 62.9
12 Swing bearing upper part mounting bolt M24 Ý 3.0 97.8 Ü 10 707 Ü 72.3
Power
13 train Swing bearing lower part mounting bolt M24 Ý 3.0 97.8 Ü 10 707 Ü 72.3
system
14 Travel motor mounting bolt M24 Ý 3.0 84 Ü 8.0 608 Ü 57.8
15 Sprocket mounting bolt M20 Ý 2.5 57.9 Ü 6.0 419 Ü 43.4
16 Carrier roller mounting bolt, nut M16 Ý 2.0 29.7Ü 3.0 215 Ü 21.7
17 Track roller mounting bolt M20 Ý 2.5 57.9 Ü 6.0 419 Ü 43.4
Under
18 Track tension cylinder mounting bolt M12 Ý 1.25 15 Ü 5.0 108 Ü 36
carriage
19 Track shoe mounting bolt, nut M22 Ý 1.5 115 Ü 5.0 831 Ü 36
20 Track guard mounting bolt M20 Ý 2.5 46 Ü 5 333 Ü 36
21 Counterweight mounting bolt M36 Ý 3.0 308 Ü 46 2228 Ü 333
22 Others Cab mounting bolt M12 Ý 1.75 12.8 Ü 3.0 92.6 Ü 21.7
23 Operator's seat mounting bolt M 8 Ý 1.25 4.05 Ü 0.8 29.3 Ü 5.8
ö For tightening torque of engine and hydraulic components, see engine maintenance guide and
service manual.
6-8
3. FUEL, COOLANT AND LUBRICANTS
1) NEW MACHINE
New machine used and filled with following lubricants.
Description Specification
Engine oil SAE 15W-40 (API CH-4)
Hyundai genuine long life hydraulic oil (ISO VG 46, VG 68 only)
Hydraulic oil
Coventional hydraulic oil (ISO VG 32)
Swing and travel reduction gear SAE 85W-140 (API GL-5)
Grease Lithium base grease NLGI No. 2
Fuel ASTM D975-No. 2
Coolant Mixture of 50% ethylene glycol base antifreeze and 50% water.
SAE Society of Automotive Engineers
API American Petroleum Institute
ISO International Organization for Standardization
NLGI National Lubricating Grease Institute
ASTM American Society of Testing and Material
6-9
2) RECOMMENDED OILS
Use only oils listed below or equivalent.
Do not mix different brand oil.
Ambient temperature ĦC(ĦF)

Capacity
Service point Kind of fluid ˶(U.S. gal) -20 -10 0 10 20 30 40
(-4) (14) (32) (50) (68) (86) (104)
SAE 30
Engine SAE 10W

Engine oil 25.5 (6.7)
oil pan
SAE 10W-30
SAE 15W-40
Swing drive 11.0 (2.9)

Gear oil SAE 85W-140
8.0Ý2
Final drive (2.1Ý2)
Tank; ISO VG 32
190 (50)
Hydraulic tank Hydraulic oil ISO VG 46
System;
330 (87) ISO VG 68
ASTM D975 NO.1

Fuel tank Diesel fuel 500 (132)
ASTM D975 NO.2
NLGI NO.1
Fitting
(Grease nipple) Grease As required
NLGI NO.2
Mixture of
Radiator antifreeze
45 (12.0) Ethylene glycol base permanent type
(Reservoir tank) and water
50 : 50
SAE : Society of Automotive Engineers

API : American Petroleum Institute
ISO : International Organization for Standardization
NLGI : National Lubricating Grease Institute
ASTM : American Society of Testing and Material
6-10
4. MAINTENANCE CHECK LIST
1) DAILY SERVICE BEFORE STARTING

Check items Service Page
Visual check
Fuel tank Check, Refill 6-29
Hydraulic oil level Check, Add 6-34
Engine oil level Check, Add 6-18
Coolant level Check, Add 6-21
Control panel & pilot lamp Check, Clean 6-45
Prefilter Check, Clean 6-33
Fan belt tension Check, Adjust 6-27
øAttachment pin and bushing Lubricate 6-44
ÂBoom cylinder tube end
ÂBoom foot
ÂBoom cylinder rod end
ÂArm cylinder tube end
ÂArm cylinder rod end
ÂBoom + Arm connecting
ÂBucket cylinder tube end
ø Lubricate every 10 hours or daily for initial 100 hours.
2) EVERY 50 HOURS SERVICE

Fuel tank (water, sediment) Drain 6-29
Track tension Check, Adjust 6-39
Swing reduction gear oil Check, Add 6-37
Swing reduction gear grease Check, Add 6-37
Bucket linkage pin & bushing Lubricate 6-44
ÂBucket cylinder rod end
ÂBucket + Arm connecting
ÂBucket control link + Arm
ÂBucket control rod
6-11
3) INITIAL 50 HOURS SERVICE
Engine oil Change 6-18
Engine oil filter Replace 6-19
Prefilter (water, element) Replace 6-33
Fuel filter Replace 6-30
Bolts & Nuts Check, Tight 6-8
ÂSprocket mounting bolts
ÂTravel motor mounting bolts
ÂSwing motor mounting bolts
ÂSwing bearing mounting bolts
ÂEngine mounting bolts
ÂCounterweight mounting bolts
ÂTurning joint locating bolts
ÂTrack shoe mounting bolts and nuts
ÂHydraulic pump mounting bolts
ö Service the above items only for the new machine, and thereafter keep the normal service
interval.

ø Return filter Replace 6-36
ø Pilot line filter Replace 6-37
ø Element in hydraulic tank breather Replace 6-36
ø Drain filter cartridge Replace 6-36
ø Replace 4 filters for continuous hydraulic breaker operation only.
5) INITIAL
NITIAL 250 HOURS SERVICE
Pilot line filter Replace 6-37
Hydraulic return filter Replace 6-36
Drain filter cartridge Replace 6-36
Swing reduction gear oil Change 6-37
6-12
Battery electrolyte Check, Clean 6-45
Swing bearing grease Lubricate 6-38
Aircon & heater fresh air filter Check 6-48
Air breather element Replace 6-36
Bolts & Nuts Check, Tight 6-8
ÂSprocket mounting bolts
ÂTravel motor mounting bolts
ÂSwing motor mounting bolts
ÂSwing bearing mounting bolts
ÂEngine mounting bolts
ÂCounterweight mounting bolts
ÂTurning joint locating bolts
ÂTrack shoe mounting bolts and nuts
ÂHydraulic pump mounting bolts
Attachment pin and bushing Lubricate 6-44
ÂBoom cylinder tube end
ÂBoom foot
ÂBoom cylinder rod end
ÂArm cylinder tube end
ÂArm cylinder rod end
ÂBoom + Arm connecting
ÂBucket cylinder tube end
7) INITIAL 500 HOURS SERVICE

Travel reduction gear oil Change 6-39

ö Service the above item only for the new machine, and thereafter keep the normal service
interval.
6-13

øEngine oil Replace 6-18
øEngine oil filter Replace 6-18, 19
Radiator, cooler fin and charge air cooler Check, Clean 6-25
÷Air cleaner element (primary) Check, Clean 6-29
Fuel filter element Replace 6-30
Prefilter Change 6-33
Corrosion register Replace 6-20
÷ Clean the primary element only after 500 hours operation or when the air cleaner warning lamp blinks.
Replace primary element and safety element after 4 times cleanings of primary element.
ø If you use high sulfur containing fuel above than 0.5% or use low grade of engine oil reduce change
interval.

Travel motor reduction gear oil Change 6-39
Swing reduction gear oil Change 6-37
Grease in swing gear and pinion Change 6-38
Hydraulic oil return filter Replace 6-36
Drain filter cartridge Replace 6-36
Pilot line filter Replace 6-37

Coolant Change 6-21, 22, 23, 24
★1
Hydraulic oil Change 6-35
Hydraulic tank suction strainer Check, Clean 6-35
★1
Conventional hydraulic oil
øChange
Change oil every 600 hours of continuous hydraulic breaker operation.

Hydraulic oil ★2 Change 6-35

★2
Hyundai genuine long life hydraulic oil
øChange
Change oil every 1000 hours of continuous hydraulic breaker operation.
6-14
12) WHEN REQUIRED
Whenever you have trouble in the machine, you must perform the service of related items, system
by system.
Fuel system
ÂFuel tank Drain or Clean 6-29
ÂPrefilter Clean or Replace 6-33
ÂFuel filter element Replace 6-30
Engine lubrication system
ÂEngine oil Change 6-18
ÂEngine oil filter Replace 6-19
Engine cooling system
ÂCoolant Add or Change 6-21, 22, 23, 24
ÂRadiator Clean or Flush 6-21, 22, 23, 24
ÂCharge air cooler Check 6-25
Engine air system
ÂAir cleaner element Replace 6-29
Hydraulic system
ÂHydraulic oil Add or Change 6-35
ÂReturn filter Replace 6-36
ÂDrain line filter Replace 6-36
ÂPilot line filter Replace 6-37
ÂElement of breather Replace 6-36
ÂSuction strainer Clean 6-35
Under carriage
ÂTrack tension Check, Adjust 6-39
Bucket
ÂTooth Replace 6-42
ÂSide cutter Replace 6-42
ÂLinkage Adjust 6-41
ÂBucket assy Replace 6-41
Air conditioner and heater
ÂFresh air filter Clean, Replace 6-48
ÂRecirculation filter Clean 6-49
6-15
5. MAINTENANCE CHART
15 9 16 18 19 1 1 17
20
5
23
2
3
6
7 11 21 26 24 4
22 4
7 8 12 10 14 13 25
3309S6MA01
Caution
1. Service intervals are based on the hour meter reading.
2. The number of each item shows the lubrication point on the machine.
3. Stop engine while filling oil, and use no open flames.
6-16
Service Service Oil Capacity Service
No. Description ˶(U.S.gal)
interval action symbol points No.
1 Hydraulic oil level Check, Add HO 190 (50) 1
2 Engine oil level Check, Add EO 25.5 (6.7) 1
10 Hours
4 Radiator coolant Check, Add C 45 (12.0) 1
or daily
5 Prefilter (water, element) Check, Clean - - 1
6 Fan belt tension and damage Check, Adjust - - 1
8 Bucket linkage pin & bushing Check, Add PGL - 6
9 Fuel tank (water, sediment) Check, Clean - - 1
50 Hours
11 Swing reduction gear case Check, Add GO 11 (2.9) 1
or weekly
12 Swing reduction gear grease Check, Add PGL 1.8 (0.5) 1
14 Track tension Check, Adjust PGL - 2
7 Attachment pins & bushing Check, Add PGL - 11
10 Swing bearing grease Check, Add PGL - 2
250
15 Battery Check, Clean - - 1
Hours
18 Air breather element Replace - - 1
21 Aircon and heater fresh air filter Check, Clean - - 1
2 Engine oil Change EO 25.5 (6.7) 1
3 Engine oil filter Replace - - 1
5 Prefilter Replace - - 1
500
22 Air cleaner element (primary) Check, Clean - - 1
Hours
23 Fuel filter element Replace - - 1
24 Radiator, oil cooler, charge air cooler Check, Clean - - 3
26 Corrosion register Replace - - 1
11 Swing reduction gear case Change GO 11 (2.9) 1
13 Swing gear and pinion grease Change PGL 16.6 kg (36.6 lb) 1
1000 16 Hydraulic oil return filter Replace - - 1
Hours 17 Drain filter cartridge Replace - - 1
20 Pilot line filter element Replace - - 1
25 Travel reduction gear case Change GO 8.0 (2.1) 2
★1
1 Hydraulic oil Change HO 190 (50) 1
2000
4 Radiator coolant Change C 45 (12.0) 1
Hours
19 Hydraulic oil suction strainer Check, Clean - - 1
5000 1 Hydraulic oil ★2 Change HO 190 (50) 1
Hours
21 Aircon & heater fresh filter Replace - - 1
As 22 Aircon & heater recirculation filter Clean, Replace - - 1
required
22 Air cleaner element (primary, safety) Replace - - 2
★1 ★2
Conventional hydraulic oil Hyundai genuine long life hydraulic oil
ö Oil symbol
Please refer to the recommended lubricants for specification.
DF : Diesel fuel GO : Gear oil HO : Hydraulic oil
C : Coolant PGL : Grease EO : Engine oil
6-17
6. SERVICE INSTRUCTION
1) CHECK ENGINE OIL LEVEL

Check the oil level with the machine on a flat
Engine oil fill
ground before starting engine.
(1) Pull out the dipstick and wipe with a clean cloth.
(2) Check the oil level by inserting the dipstick
completely into the hole and pulling out again.
(3) If oil level is LOW, add oil and then check again.
ö If the oil is contaminated or diluted, change
the oil regardless of the regular change inter-
val.
ö Check oil level after engine has been stopped
for 15 minutes.
Do not operate unless the oil level is in the Normal
normal range.
Dipstick
36076MA06
2) REPLACEMENT OF ENGINE OIL AND OIL FILTER

(1) Warm up the engine.
(2) Remove the plug and allow the oil to drain.
ÂWrench size : 17 mm
ö A drain pan with a capacity of 28 liters
(7.4U.S. gallons) will be adequate.
36076MA06A
(3) Clean around the filter head, remove the filter

and clean the gasket surface.
ÂWrench size : 75 ~ 85 mm (3.0~3.3 in)
ö The o-ring can stick on the filter head.
Make sure it is removed before installing the
new filter.
36076MA06B
6-18
(4) Apply a light film of lubricating oil to the gasket
sealing surface before installing the filters. Oil
ö Fill the filters with clean lubricating oil.
Oil
18036MI09
(5) Install the filter to the filter head.

ö Mechanical over-tightening may distort the
threads or damage the filter element seal.
ÂInstall the filter as specified by the filter
manufacturer.
18036MI10
(6) Fill the engine with clean oil to the proper level.
ÂQuantity : 25.5˶(6.7 U.S.gallons)
Oil
36076MA06C
(7) Operate the engine at low idle and inspect for

leaks at the filters and the drain plug.
Shut the engine off and check the oil level with
the dipstick. Allow 15minutes for oil to drain
down before checking.
36076MA06D
6-19
3) REPLACEMENT OF WATER FILTER (CORR-
OSION RESISTER)
(1) Turn the shut off valve to the OFF position by
rotating the knob from vertical to horizontal as
figure.
Wait until the temperature is below 50˚C 50˚
(122˚C)) before removing the radiator cap.
(122˚
Remove the coolant system radiator cap and
36076MI10
close the shutoff valve before removing the
water filter. Failure to do so can result in
personal injury from heated coolant spray.
(2) Remove and discard the water filter.
Clean the gasket surface.
36076MI11
(3) Apply a thin film of lubricating oil to the gasket

sealing surface before installing the new water
filter.
Do not allow oil to get into the filter.
Oil will damage the DCA.
18036MI12
(4) Install the water filter on the filter head. Tighten

the filter until the gasket contacts the filter head
surface.
Tighten the water filter an additional 1/2 to 3/4 of
a turn or as specified by the filter manufacturer.
Mechanical overtightening can distort the
threads or damage the filter head.
36076MI13
6-20
(5) Install the radiator cap.
(6) Operate the engine until it reaches a temperat-
ure 80˚C
C (176˚F
F) and check for coolant leaks.
21076MA10A
4) CHECK COOLANT
(1) Check if the level of coolant in reservoir tank is
between FULL and LOW.
(2) Add the mixture of antifreeze and water after
removing the cap of the reservoir tank if coolant
is not sufficient.
(3) Be sure to add the coolant by opening the cap of
raditor when coolant level is below LOW.
3009SH6MA04
(4) Replace gasket of radiator cap when it is

damaged.
Hot coolant can spray out if radiator cap is
removed while engine is hot. Remove the
cap after the engine has cooled down.
CLUSTER CLUSTER CLUSTER CLUSTER
TYPE 1 TYPE 2 TYPE 1 TYPE 2
OK NOT OK
2209S6MA08
6-21
5) FLUSHING AND REFILLING OF RADIATOR CLUSTER TYPE 1 CLUSTER TYPE 2
(1) Change coolant
Avoid prolonged and repeated skin contact
with used antifreeze. Such prolonged
repeated contact can cause skin disorders or
other bodily injury.
Avoid excessive contact-wash thoroughly
after contact.
Keep out of reach of children. 2209S6MA09
ö Protect the environment : Handling and dis-

posal of used antifreeze can be subject to
federal, state, and local law regulation.
Use authorized waste disposal facilities,
including civic amenity sites and garages
providing authorized facilities for the receipt of
used antifreeze.
If in doubt, contact your local authorities for
guidance as to proper handling of used
antifreeze.
Wait until the temperature is below 50˚C 50˚

(122˚F) before removing the coolant system
pressure cap.
Failure to do so can cause personal injury
from heated coolant spray.
Drain the cooling system by opening the drain
valve on the radiator and removing the plug in
the bottom of the water inlet. A drain pan with a
capacity of 45 liters (12U.S.gallons) will be
18036MI16
adequate in most applications.
(2) Flushing of cooling system OK

Η Fill the system with a mixture of sodium
carbonate and water(or a commercially
available equivalent).
ö Use 0.5 kg (1.0 pound) of sodium carbonate
for every 23 liters (6.0 U.S. gallons) of water.
ö Do not install the radiator cap. The engine is
to be operated without the cap for this
process.
18306MI17
6-22
ö During filling, air must be vented from the
engine coolant passages. Open the engine
venting petcock.
The system must be filled slowly to prevent
air locks. Wait 2 to 3 minutes to allow air to
be vented, then add mixture to bring the
level to the top.
18036MI18
Θ Operate the engine for 5 minutes with the

coolant temperature above 80˚C
C (176˚F).
Shut the engine off, and drain the cooling
system. CLUSTER CLUSTER
TYPE 1 TYPE 2
START
ON
OFF 2209S6MA10
Ι Fill the cooling system with clean water.

ö Be sure to vent the engine and aftercooler
for complete filling.
ö Do not install the radiator cap or the new
coolant filter.
18306MI20
Κ Operate the engine for 5 minutes with the

coolant temperature above 80˚C
C (176˚F).
Shut the engine off, and drain the cooling
system. CLUSTER CLUSTER
TYPE 1 TYPE 2
ö If the water being drained is still dirty, the
system must be flushed again until the water
is clean.
START
ON
OFF 2209S6MA10
6-23
(3) Cooling system filling
Η Use a mixture of 50 percent water and 50
percent ethylene glycol antifreeze to fill the
cooling system.
Coolant capacity(engine only) : 10.4˶ (2.7 U.S.
gallons)
ö Use the correct amount of DCA4 corrosion
inhibitor to protect the cooling system.
18036MI22
Θ The system has a maximum fill rate of 19 liters

(5.0 U.S. gallons)
Do not exceed this fill rate.
ö The system must be filled slowly to prevent
air locks.
During filling, air must be vented from the
engine coolant passage.
Be sure to open the petcock.
Then add mixture to bring the level to the
18036MI23
top.
Ι Install the pressure cap. Operate the engine

until it reaches a temperature 80˚CC (176˚F),
and check for coolant leaks.
Check the coolant level again to make sure the
system is full of coolant. NOT OK
CLUSTER CLUSTER
TYPE 1 TYPE 2 2209S6MA11
6-24
6) CLEAN RADIATOR AND OIL COOLER NOT OK
Check, and if necessary, clean and dry outside of
radiator and oil cooler. After working in a dusty
place, clean radiator more frequently.
(1) Visually inspect the radiator for clogged radiator
fins.
(2) Use 550 kPa (80 psi) air pressure to blow the dirt 550 kPa
and debris from the fins. (80 psi)
13036MI01
Blow the air in the opposite direction of the fan
air flow.
(3) Visually inspect the radiator for bent or broken
fins.
ö If the radiator must be replaced due to bent or
broken fins which can cause the engine to
ove r h e a t , r e fe r t o t h e m a nu fa c t u r e r ' s
replacement procedures.
(4) Visually inspect the radiator for core and gasket
leaks.
13036MI02
7) CHECK CHARGE AIR COOLER

Inspect the charge air cooler for dirt and debris
blocking the fins. Check for cracks, holes, or other
damage. If damage is found, please contact
Hyundai distributor.
36076MI02
6-25
8) FAN BELT TENSION
(1) Inspect the drive for damage. OK
NOT OK
13036MI03
(2) Inspect the drive belt and fan hub.
18036MI27
9) INSPECTION OF COOLING FAN

Personal injury can result from a fan blade
failure. Never pull or pry on the fan. This can
damage the fan blade and cause fan failure.
ö Rotate the crankshaft by using the engine
barring gear.
ö A visual inspection of the cooling fan is NOT OK
required daily.
Check for cracks, loose rivets, and bent or
loose blades. 21076MA10B
Check the fan to make sure it is securely
mounted. Tighten the capscrews if necessary.
Replace any fan that is damaged.
6-26
10) BELT TENSIONER, AUTOMATIC Adjustment
(1) Every 1000hours, or 1 year, whichever occurs
first, inspect the automatic belt tensioner.
With the engine turned off, check that neither the
top nor bottom tensioner arm stop is touching
the cast boss on the tensioner body. If either of
the stops is touching a boss, the alternator belt
must be replaced. Check to make sure the
correct belt part number is being used it either 7807AMI50
condition exists.
(2) Check the tensioner pulley and body for cracks.

If any cracks are noticed, the tensioner must be
replaced. Refer to a Cummins Authorized
Repair facility. Check the tensioner for dirt
buildup. If this condition exists, the tensioner
must be removed and steam-cleaned.
7807AMI51
(3) Check that the bottom tensioner arm stop is in

contact with the bottom tensioner arm stop boss
on the tensioner body. If these two are not
touching, the tensioner must be replaced.
7807AMI52
(4) Inspect the tensioner for evidence of the pivoting

tensioner arm contacting the stationary circular
base. If there is evidence of thess two areas
touching, the pivot tube bushing has failed and
the tensioner must be replaced.
7807AMI53
6-27
(5) A worn tensioner that has play in it or a belt that
"walks" off its pulley possibly indicates pulley
misalignment.
ö M a x i mu m p u l l ey m i s l i g n m e n t i s t h r e e
degrees. This measurement can be taken
with a straightedge and an inclinometer.
(6) Install the belt.
7807AMI54
6-28
10) CLEANING OF AIR CLEANER
(1) Primary element
Η Loosen the clamps and remove the element.
Θ Clean the inside of the body.
Ι Clean the element with pressurized air.
ÂRemove the dust inside of the element by the
pressurized air (below 3 kgf/cm 2, 40 psi)
forward and backward equally.
Κ Inspect for cracks or damage of element by
putting a light bulb inside of the element.
Wing nut
Λ Insert element and tighten wing nut.
Pressurized air
ö Replace the primary element after 4 times 3kgf/cm2 below
cleanings.
(2) Safety element
ö Replace the safety element only when the
primary element is cleaned for the 4 times.
ö Always replace the safety element. Never
attempt to reuse the safety element by
cleaning the element.
2907A6MI22
12) FUEL TANK

(1) Fill fuel fully when system the operation to mini-
mize water condensation, and check it with fuel
gauge before starting the machine.
(2) Drain the water and sediment in the fuel tank by
opening the drain cock.
ö Be sure to LOCK the cap of fuel tank. Fuel gauge
ö Remove the strainer of the fuel tank and
clean it if contaminated.
Stop the engine when refueling.
All lights and flames shall be kept at a safe
Drain cock
distance while refueling.
3309S6MA05
6-29
13) REPLACEMENT OF FUEL FILTER
(1) Clean around the filter head, remove the filter
and clean the gasket surface.
ÂWrench size : 90~95 mm (3.5~3.8 in)
(2) Replace the O-ring.
(3) Fully fill fuel in the new filter.
Cartridge
(4) Apply engine oil on the gasket of new filter when
mounting, and tighten 3/4 to 1 turn more after 21076MA13A
the gasket touches the filter head.

(5) Relieve the air after mounting.
ö Check for fuel leakage after the engine starts.
ö If air is in the fuel system, the engine will not
start, Start engine after bleeding the air
according to the method of bleeding air.
FUEL WATER SEPARATOR

- Drain the water and sediment from the
separator daily.
- Shut off the engine. Open Close
- Use your hand to open the drain valve.
- Turn the valve counterclockwise 4 complete
turns until the valve drops down 1".
- Drain the filter sump of water until clear fuel is
visible.
ö Do not overtighten the valve.
Overtightening can damage the threads.
- Push the valve up and turn the valve clockwise
to close the drain valve.
ö If more then 2 ozs is drained, refilling of the
filter is required to prevent hard starting. Open Close
Refer to low pressure lines and fuel filter
venting clause 12)-(2). 21076MA13B
6-30
14) BLEEDING THE FUEL SYSTEM
(1) Air in fuel
Η The air bleed fitting on the fuel system creates
a self bleeding system during replacement of
the supply side components. High pressure
fuel line removal and replacement will not
require external bleeding to start the engine.
The fuel pump will create high fuel pressure
during cranking and purge the air in the high
pressure side through the injectors.
36076MA33
ö If an excessive amount of air has entered the

system, the system will need to be bled.
Θ Loosen the fuel supply line at the pump.
Run the electric fuel lift pump until the air has
been bled. When all the air has been bled,
tighten the fitting.
36076MA34
Ι Supply line leaks from the lift pump to the fuel

pump can be located by operating the lift pump
or keyswitch cycling, to build pressure in the
fuel lines. Inspect all lines and connections, as
well as the fuel filter assembly, for an external
fuel leak.
36076MA35
6-31
Κ A stuck open injector can also blow combustion
gas back into the pump and cause air to be
present in the overflow.
If the engine seems to be misfiring or running
rough, break all the injector supply lines loose
at the pump end. Crank the engine and
observe the lines. If combustion gas seems to
be blowing back through the line, the injector is
stuck open.
ö Use two wrenches when loosening the lines
at the fuel pump, one to hold the delivery
valve and one to loosen the line.
ÂWrench size : 19 mm
ÂTightening torque : 2.45 kgf·m (18 lbf·ft)
36076MA36
(2) Venting the high pressure lines

NOT OK
The pressure of the fuel in the line is
sufficient to penetrate the skin and cause
serious bodily harm.
Η Loosen the fittings at the cylinder head and
crank the engine to allow entrapped air to bleed
from the line. Tighten the fittings. START
ÂWrench size :19mm ON
OFF
ÂTorque : 3.9 kgf·m (28 lbf·ft)
Θ Start the engine and vent one line at a time until 30 Seconds
the engine runs smoothly.
Do not bleed a hot engine as this can cause
fuel to spill onto a hot exhaust manifold, cre-
ating a danger of fire. 21076MA37
6-32
15) PREFILTER
ö Inspect or drain the collection bowl of water
daily and replace the element every 500
hours.
(1) Drain water
Η Open bowl drain valve to evacuate water.
Θ Close drain valve.
Bowl
Drain valve
Open Close
Hydraulic tank
4507A6MA35
(2) Replace element

Η Drain the unit of fuel. Follow "Drain water"
instructions above.
Θ Remove element and bowl from filter head. Open Bowl
ö The bowl is reusable, do not damage or dis-
card.
Ι Separate element from bowl. Clean bowl and Hydraulic tank
seal gland.
4507A6MA36
Κ Lubricate new bowl seal with clean fuel or

motor oil and place in bowl gland. Filter head
Λ Attach bowl to new element firmly by hand.
Μ Lubricate new element seal and place in
Close
element top gland. Element
Ν Attach the element and bowl to the head. Bowl
Close
4507A6MA37
6-33
16) LEAKAGE OF FUEL FIRE !!
Be careful and clean the fuel hose, injection
pump, fuel filter and other connections as the
leakage from these part can cause fire.
29076MI35
17) HYDRAULIC OIL CHECK

(1) Stop the engine after retract the arm and bucket Red line
cylinders, then lower the boom and set the

bucket on the ground at a flat location as in the
Level gauge
illustration.
(2) Check the oil level at the level gauge of hydraulic
oil tank.
(3) The oil level is normal if between the red lines. 21076MA14
18) FILLING HYDRAULIC OIL

(1) Stop the engine to the position of level check.
(2) Relieve the pressure in the tank by pushing the Air breather
top of the air breather.
(3) Remove the breather on the top of oil tank and
fill the oil to the specified level.
(4) Start engine after filling and operate the work
equipment several times.
(5) Check the oil level at the level check position
after engine stops.
3309S6MA08
6-34
19) CHANGE HYDRAULIC OIL
(1) Lower the bucket on the ground pulling the arm
and bucket cylinder to the maximum. Air breather
Cover
(2) Relieve the pressure in the tank by pushing the O-ring
(3) Remove the cover.
ÂTightening torque : 6.9Ü1.4 kgfÂm
(50Ü10 lbfÂft)
(4) Prepare a suitable container.
(5) To drain the oil loosen the drain plug at the bot-
tom of the oil tank.
(6) Fill proper amount of recommended oil.
(7) Put the breather in the right position.
(8) Bleed air hydraulic pump loosen the air
breather at top of hydraulic pump assembly.
Drain valve
(9) Start engine and run continually. Release the
air by full stroke of each control lever. 3309A6MI21
20) CLEAN SUCTION STRAINER

Air breather
Clean suction strainer as follows paying attention Cover
O-ring
to the cause to be kept during oil filling.
(50Ü10 lbfÂft)
Strainer
(2) Pull out the strainer in the tank.
(3) Wash the foreign material on the suction strainer
with gasoline or cleaning oil.
(4) Replace the suction strainer if it is damaged.
(5) Assemble with reverse order of disassembly.
Be sure to install a new O-ring and reinsert in
the oil tank.
ö Loosen the bolt slowly at the cover can be
spring out by the spring when removing it.
3309S6MA09
6-35
21) REPLACEMENT OF RETURN FILTER
Replace as follows paying attention to the cause Cover
to be kept during the replacement. O-ring
Spring
(1) Remove the cover. Bypass valve
(50Ü10 lbfÂft)
Element
(2) Remove the spring, by-pass valve, and return fil-
ter in the tank.
(3) Replace the element with new one.
3309S6MA11
22) REPLACEMENT OF ELEMENT IN HYDRAULIC

TANK BREATHER Cover
Snap ring
(1) Relieve the pressure in the tank by pushing the Element
(3) Remove the snap ring and pull out the filter
element.
(4) Replace the filter element new one.
(5) Reassemble by reverse order of disassembly.
Â Tightening torque : 0.2~0.3 kgfÂm
(1.4~2.1 lbfÂft)
3309S6MA12
23) REPLACE OF DRAIN FILTER CARTRIDGE

Clean the dust around filter and replace with new
Drain filter
one after removing the cartridge.
ö Tighten about 2/3 turn more after the gasket of
cartridge contacts seal side of filter body for
mounting.
ö Change car tridge after initial 50 hours of
operation. Thereafter, change cartridge every Hydraulic
oil tank
1000 hours.
3309S6MA13
6-36
24) REPLACE OF PILOT LINE FILTER
Solenoid
(1) Loosen the nut positioned on the filter body. valve
A
5
P1
(2) Pull out the filter element and clean filter
A
4
housing. P4
P
A1
2
A2
(3) Install the new element and tighten using A3
specified torque.
ö Change cartridge after initial 250 hours of
operation. Thereafter, change cartridge every
1000 hours. 21096MA25
25) CHECK THE SWING REDUCTION GEAR OIL

(1) Pull out the dipstick and clean it.
(2) Insert it again.
(3) Pull out one more time to check the oil level and
fill the oil if the level is not sufficient.
32096MI11
26) CHANGE SWING REDUCTION GEAR OIL

Cap
(1) Raise the temperature of oil by swinging the
machine before replace the oil and park the Drain valve
machine on the flat ground.
Filling port
(2) Loosen the plug of the drain port. plug
(3) Drain into a proper container.
(4) Wash the drain plug and reinstall it with sealing
tape.
Fill proper amount of recommended oil. 32096MI12
ÂAmount of oil : 11.0˶ 2.9 U.S.gal)
27) LUBRICATE BEARING OF OUTPUT SHAFT IN Air vent

REDUCTION GEAR port plug
(1) Remove air vent plug.

Grease filling nipple
(2) Remove grease fill plug and install grease filling
hose and nipple at that place.
(3) Lubricate NLGI No.2 with grease gun until
comes out new grease from air vent port.
ÂAmount of oil : 1.8˶(0.5 U.S.gal)
(4) Wash the air vent plug and reinstall it with seal-
ing tape. 32096MI13
6-37
28) LUBRICATE SWING BEARING
(1) Grease at 2 fitting.
ö Lubricate every 250 hours.
3309A6MI18
29) SWING GEAR AND PINION

(1) Drain old grease
Η Remove under cover of lower frame.
Θ Remove drain cover of lower frame.
Ι Remove filler cover of upper frame. Filler cover
Κ Operate full turn (360Á) of swing several times.
FRONT
Filler hole
1407A6MA28
(2) Refill new grease

Η Install drain cover.
FRONT
Θ Fill with new grease.
Ι Install filler cover.
ÂCapacity : 11.4 kg (25.1 lb)
Top of
lower frame
Drain cover
REAR
2507A6MA29
30) CHECK THE TRAVEL REDUCTION GEAR OIL

(1) Operate the machine to the position of drain
plug down to the flat ground.
(2) Loosen the level plug and check the oil level.
If the level is at the hole of the plug, it is normal. Fil
Oi l
Fill the oil if it is not sufficient. l le
ve
l
ÂAmount of oil : 8.0˶(2.1 U.S.gal) Dr
ain
2907A6MI09
6-38
31) CHANGE OF THE TRAVEL REDUCTION GEAR OIL
(1) Raise the temperature of the oil by traveling
machine first.
(2) Stop when the position of the drain plug is down.
(3) Loosen the level plug and then the drain plug.
Fi
Oil ll
(4) Drain the oil to adequate container. lev
el
(5) Tighten the drain plug and fill specified amount Dr
ain
of oil at filling port.
(6) Tighten the level plug and travel slowly to check
if there is any leakage of oil. 2907A6MI10
32) LUBRICATE RCV LEVER

Remove the bellows and with a grease gun A B
grease the joint part (A) and sliding parts (B).
21076MA25
33) ADJUSTMENT OF TRACK TENSION

ö It is important to adjust the tension of track
properly to extend the lifetime of track and
90 ~ 110
traveling device.
ö The wear of pins and bushings on the under-
carriage will vary with the working conditions
and soil properties.
It is thus necessary to continually inspect the Bottom of track frame Track frame
track tension so as to maintain the standard
tension on it.
(1) Raise the chassis with the boom and arm. L
(2) Measure the distance between bottom of track
frame on track center and track of shoe.
ö Remove mud with rotating the track before Back of shoe Track shoe
measuring. 21076MA27
6-39
(3) If the tension is tight, drain the grease in the Length (L)
grease nipple and if the tension is loose, charge
360~390 mm 14.2~15.5"
the grease.
Personal injury or death can result from
grease under pressure.
When loosening the grease nipple, do not
loosen more than one turn as there is a
danger of a spring coming out of the nipple
because of the high pressure inside.
ö When the grease is drained, move the track
to the forward and backward slightly.
If the track tension is loose even after the
grease is charged to the maximum, change
the pins and bushings as there are worn
seriously.
6-40
34) REPLACEMENT OF BUCKET
When knocking the pin in with a hammer,
metal particles may fly and cause serious
injury, particularly if they get into your eyes.
When carrying out this operation, always
wear goggles, helmet, gloves, and other pro-
tective equipment.
ö When the bucket is removed, place it in a sta-
ble condition.
21076MA28
ö When performing joint work, make sure sig-
nals to each other and work carefully for safe-
ty's sake.
(1) Lower the bucket on the ground as the picture
shown in the right. 1
(2) Lock the safety lever to the LOCK position and 3
stop the engine. 2
1
(3) Remove the stopper bolts (1) and nuts (2), then
4
remove pins (3, 4) and remove the bucket.
ö When removing the pins, place the bucket so 2
that it is in light contact with the ground.

36076MA26
ö If the bucket is lowered strongly to the
ground, the resistance will be increased and it
will be difficult to remove the pins.
ö After remove the pins, make sure that they do
not become contaminated with sand or mud
and that the seals of bushing on both sides
do not become damaged. B
(4) Align the arm with holes (A) and the link with A
holes (B), then coat with grease and install
pins(3, 4)
ö When installing the bucket, the O-rings are 13036MI15
easily damaged, so fit the O-rings on the

boss of the bucket as shown in the picture.
After knocking the pin, move the O-ring down
to the regular groove.
(5) Install the stopper bolt (1) and nuts (2) for each
pin, then grease the pin.
36076MI36
6-41
35) REPLACEMENT OF BUCKET TOOTH
(1) Timing of replacement
Η Check wearing condition as shown in the
illustration and replace tooth tip before adapter Tooth adapter
Tooth tip
starts to wear.
Θ If excessive use, tooth adapter has worn out,
replacement may become impossible.
13036MI20
(2) Instructions for replacement

Η Pull out pin by striking pin with punch or
hammer, avoiding damage to locking washer.
Θ Remove dust and mud from surface of tooth
adapter by using knife.
Tooth pin Tooth adapter
Ι Place locking washer in its proper place, and fit
tooth tip to adapter.
Tooth tip Locking washer
Κ Insert pin until locking washer is positioned at
tooth pin groove.
Personal injury can result from bucket falling.
13036MI21
Block the bucket before changing tooth tips
or side cutters.
6-42
36) ADJUSTMENT OF BUCKET CLEARANCE
(1) Lower the bucket on the ground as the picture
shown in the right.
(2) Swing to the left and keep the arm boss to be
contact to the bucket left.
(3) Lock the safety lever to the LOCK position and
stop the engine.
(4) Measure the clearance (A) between bucket and
arm boss. This is the total clearance.
(5) Adjusting
Η Loosen bolt (2), and remove washer (3), plate
(1) and shim (4).
Θ Remove the shim equivalent value with
measuring value.
Ι Assemble the parts in the reverse order of 1
removal. 2
ÂTightening torque : 29.6Ü3.2 kgfÂm 3
(214.0Ü23.1 lbfÂft)
ÂNormal clearance : 0.5 ~ 1.0 mm 4
(0.02 ~ 0.04 in) Bucket Arm boss Bushing
ö If the bucket is not adjusted correctly, noise
and vibration created during operation, and
damaged O-ring, pin and bushing quickly. 36076MI37
6-43
37) LUBRICATE PIN AND BUSHING
(1) Lubricate to each pin of working device
Lubricate the grease to the grease nipple
according to the lubricating interval.
No. Description Qty
4 3 1
1 Lubrication manifold at boom 5
2 Boom cylinder pin 2
3 Boom and arm connection pin 1
4 Arm cylinder pin (Rod side) 1
Bucket cylinder pin (Head, rod) 2 5 26
Bucket link (Control rod) 3
5
Arm and control link connection pin 1
Arm and bucket connection pin 1
6 Boom rear bearing center 1
ö Shorten lubricating interval when working 21074OP26
in the water or dusty place.
(2) Dust seals are mounted on the rotating part of

working device to extend the lubricating interval.
ö Mount the lip to be faced outside when
replace the dust seal.
21076MA28
ö If it is assembled in wrong direction, it will

cause fast wear of pin and bushing, and
create noise and vibration during operation.
ö Assemble the seal same direction with picture
and use with plastic hammer when replace.
Outside
13036MI28
6-44
7. ELECTRICAL SYSTEM
1) WIRING, GAUGES
Check regularly and repair loose or malfunctioning
gauges when found.
13036MI29
2) BATTERY
(1) Clean
Η Wash the terminal with hot water if it is contami-
nated, and apply grease to the terminals after
washing.
Battery gas can explode. Keep sparks and
flames away from batteries.
Always wear protective glasses when working
with batteries.
Do not stain clothes or skin with electrolyte
as it is acid.
Be careful not to get the electrolyte in eyes.
Wash with clean water and go to the doctor if
it enters the eyes. 36070FW05
(2) Recycle
Never discard a battery.
Always return used batteries to one of the
following locations.
ÂA battery supplier
ÂAn authorized battery collection facility
ÂRecycling facility
(3) Method of removing the battery cable

Remove the cable from the ground connection
first ( terminal side) and reconnect it last
when reassembling. Battery relay
Ground
13036MI32
6-45
3) STARTING THE ENGINE WITH A BOOSTER CABLE
Keep following order when you are going to start
engine using booster cable.
(1) Connection of booster cable
Connection of booster cable
ö Use the same capacity of battery for starting.
Η Make sure that the starting switches of the nor-
Red
mal machine and trouble machine are both at
the OFF position. Ι Θ Η
Θ Connect the red terminal of booster cable to
the battery (+) terminal between exhausted and
new battery.
Normal (New) Trouble (Exhausted)
ΙConnect the black terminal of the booster cable machine machine
between new battery (-) terminal and chassis of Black
Κ
trouble machine. To chassis of trouble machine
ö Keep firmly all connection, the spark will be
caused when connecting finally. Connection order : ΗĄΘĄΙĄΚ
13036MI33
(2) Starting the engine

Η Starting the engine of the normal machine and
keep it to run at high idle.
Θ Start engine of the trouble machine with start-
START
ing switch.
Ι If you can not start it by one time, restart the ON
OFF
21076MA29
engine after 2 minutes.
(3) Taking off the booster cable Disconnection of booster cable

Η Take off the booster cable (black).
Θ Take off the booster cable (red) connected to
the (+) terminal.
Red
Ι Run engine with high idle until charging the
exhausted battery by alternator, fully. Ι Θ Η
Explosive gas is generated while using the
battery or charging it. Keep away flame and
be careful not to cause the spark. Normal (New) Trouble (Exhausted)
ö Charge the battery in the well ventilated machine machine
Black
place. Κ
To chassis of trouble machine
ö Place the machine on the earth or concrete.
Avoid charging the machine on the steel
plate.
Disconnection order : ΚĄΙĄΘĄΗ
ö Do not connect (+) terminal and (-) terminal
when connecting booster cable because it
13036MI33
will be shorted.
6-46
(4) Welding repair
Before start to welding, follow the below proce-
Fuel tank
dure.
Master
Η Shut off the engine and remove the starting switch MOD
PARTEL : R290
NO
Y
R
G
LC-9
: 21Q8
BH
-3273
0
switch.
Θ Disconnect ground cable from battery by mas-
DISCONNECT SWITCH
OFF
MCU
ter switch.
Ι Before carrying out any electric welding on the
machine, the battery cables should be discon-
nected and the connectors pulled out of the
electronic control units (MCU, cluster etc).
Κ Connect the earth (ground) lead of the welding Battery
equipment as close to the welding point as pos-
sible. Cluster type 1 Cluster type 2
ö Do not weld or flame cut on pipes or tubes
that contain flammable fluids. Clean them Wo
rk
Mo
de
Use
r Mo
de
Pow
er
Mo
de
el
Tra
vel
Spe
ed
Sel
ect
o Dec
Aut
thoroughly with nonflammable solvent before

welding or flame cutting on them.
Do not attempt to welding work before carry CN-56
out the above. CN-56
If not, it will caused serious damage at elec-

tric system. 3009SH6MA16
6-47
1) CLEAN AND REPLACE OF FRESH AIR FILTER
ö Always stop the engine before servicing. SEEK

MUTE
V
MODE
CALL
(1) Open the LH side cover.
LH side cover
21096MA40
(2) Remove the fresh air filter. Fresh

ö When installing a filter, be careful not to air filter
change the filter direction.
CALL
MUTE
MODE
V
SEEK
Outside
Inside
21096MA41
(3) Clean the filter using a pressurized air (below 2

kgf/cm2, 28 psi).
When using pressurized air, be sure to wear Inside
safety glasses.
Outside
(4) Inspect the filter after cleaning. If it is damaged
or badly contaminated, use a new filter. Pressurized air
2 kgf/cm2 below
13036MI34
2) CLEAN AND REPLACE OF RECIRCULATION VOL
FILTER
ö Always stop the engine before servicing.
(1) Move seat and console box to arrow direction
using the adjust lever.
Recirculation
filter
Adjust lever
21096MA42
6-48
(2) Remove recirculation filter. VOL
Recirculation
filter
21096MA43
(3) Clean the recirculation filter using a pressurized

air (b
b elow 2 kgf/cm2, 28 psi) or washing with
water.
When using pressurized air, be sure to wear
safety glasses.
ö Dry off after washing with water.
Pressurized air
(4) Inspect the filter after cleaning. If it is damaged 2 kgf/cm2 below
or badly contaminated, use a new filter.
13036MI35
3) PRECAUTIONS FOR USING AIR CONDITIONER

(1) When using the air conditioner for a long time,
open the window once every one hour.
(2) Be careful not to overcool the cab.
(3) The cab is properly cooled if the operator feels
cool when entering there from outside (about
5˚C lower than the outside temperature).
(4) When cooling, change air occasionally.
4) CHECK DURING SEASON
Ask the service center for replenishment of
refrigerant or other maintenance service so that
the cooling performance is not damaged.
5) CHECK DURING OFF-SEASON
Operate the air conditioner 2 or 3 times a
month (each for a few minutes) to avoid loss of oil
film in the compressor.
6-49
1) CLEAN AND REPLACE OF FRESH AIR FILTER
ö Always stop the engine before servicing. SEEK

MUTE
V
MODE
CALL
(1) Open the LH side cover.
LH side cover
21096MA40
(2) Remove the fresh air filter. Fresh

ö When installing a filter, be careful not to air filter
change the filter direction.
CALL
MUTE
MODE
V
SEEK
Outside
Inside
21096MA41
(3) Clean the filter using a pressurized air (below 2

kgf/cm2, 28 psi).
When using pressurized air, be sure to wear Inside
safety glasses.
Outside
(4) Inspect the filter after cleaning. If it is damaged
or badly contaminated, use a new filter. Pressurized air
2 kgf/cm2 below
13036MI34
2) CLEAN AND REPLACE OF RECIRCULATION VOL
FILTER
ö Always stop the engine before servicing.
(1) Move seat and console box to arrow direction
using the adjust lever.
Recirculation
filter
Adjust lever
21096MA42
6-48
(2) Remove recirculation filter. VOL
Recirculation
filter
21096MA43
(3) Clean the recirculation filter using a pressurized

air (b
b elow 2 kgf/cm2, 28 psi) or washing with
water.
When using pressurized air, be sure to wear
safety glasses.
ö Dry off after washing with water.
Pressurized air
(4) Inspect the filter after cleaning. If it is damaged 2 kgf/cm2 below
or badly contaminated, use a new filter.
13036MI35
3) PRECAUTIONS FOR USING AIR CONDITIONER

(1) When using the air conditioner for a long time,
open the window once every one hour.
(2) Be careful not to overcool the cab.
(3) The cab is properly cooled if the operator feels
cool when entering there from outside (about
5˚C lower than the outside temperature).
(4) When cooling, change air occasionally.
4) CHECK DURING SEASON
Ask the service center for replenishment of
refrigerant or other maintenance service so that
the cooling performance is not damaged.
5) CHECK DURING OFF-SEASON
Operate the air conditioner 2 or 3 times a
month (each for a few minutes) to avoid loss of oil
film in the compressor.
6) Refrigerant amount : 800 ± 20 g
6-49
TROUBLESHOOTING GUIDE
1. ENGINE
öThis guide is not intended to cover every conditions, however many of the more common
possibilities are listed.
Trouble Service Remark
The engine oil pressure lamp Â Add the oil to the specified level.
lights ON when engine speed is Â Replace the oil filter cartridge.
raised after completion of warm
up. Â Check oil leakage from the pipe or the joint.
Â Replace the monitor.
Steam is emitted from the top Â Supply the coolant and check leakage.
part of the radiator (the pressure Â Adjust fan belt tension.
valve).
Coolant level warning lamp lights Â Wash out inside of cooling system.
ON. Â Clean or repair the radiator fin.
Â Check the thermostat.
Â Tighten the radiator cap firmly or replace the
packing of it.
Â Replace the monitor.
The engine does not start when Â Add fuel.

the starting motor is turned over. Â Repair where air is leaking into fuel system.
Â Check the injection pump or the nozzle.
Â Check the valve clearance.
Â Check engine compression pressure.
Â In cold weather, check if fuel warmer system Refer to the pages
is working normal. 3-34, 4-4 and 4-8.
Exhaust gas is white or blue. Â Adjust to specified oil quantity.

Â Replace with specified fuel.
Exhaust gas occasionally turns Â Clean or replace the air cleaner element.
black. Â Check the nozzle.
Â Check engine compression pressure.
Â Clean or replace the turbocharger.
Combustion noise occasionally Â Check the nozzle.

changes to breathing sound.
Unusual combustion noise or Â Check with specified fuel.

mechanical noise. Â Check over-heating
Â Replace the muffler.
Â Adjust valve clearance.
7-1
2. ELECTRICAL SYSTEM
Lamp does not glow brightly even Â Check for loose terminals and open-circuit wiring.
when engine runs at high speed.
Â Adjust belt tension.
Lamp flickers while engine runs.
Battery charging lamp does not Â Check the alternator.

go out even when engine runs at
Â Check and repair wiring.
high speed.
Unusual noise is emitted from the Â Check the alternator.

alternator.
Starting motor does not turn Â Check and repair the wiring.
when starting switch is turned ON.
Â Charge the battery.
Â Check the starting motor.
Â Check the safety relay.
The pinion of the starting motor Â Charge the battery.

keeps going in and out.
Â Check the safety relay.
Starting motor turns the engine Â Charge the battery.

sluggishly.
Â Check the starting motor.
The starting motor disengages Â Check and repair the wiring.

before the engine starts up.
Â Charge the battery.
The engine warming up lamp Â Check and repair wiring.

does not go ON.
Â Check the monitor.
The engine oil pressure lamp Â Check the monitor.

does not light up when engine is
ÂCheck the caution lamp switch.
stationary (when the starting
switch is in ON position.)
Battery charging lamp does not Â Check the monitor.

light up when the engine is sta-
ÂCheck and repair the wiring.
tionary.
(when the starting switch is in ON
position.)
7-2
3. OTHERS
Track slip out of place. Â Adjust tension of track.

Excessive wear of the sprocket.
Bucket either rises slowly or not at Â Add oil to specified level.
all.
Slow speed of travel, swing, Â Add oil to specified level.
boom, arm and bucket.
Unusual noise emitted from pump. Â Clean the hydraulic tank strainer.
Excessive oil temperature rise of Â Clean the oil cooler.

hydraulic oil. Â Adjust fan belt tension.
Â Add oil to specified level.
7-3
HYDRAULIC BREAKER AND QUICK CLAMP
1. SELECTING HYDRAULIC BREAKER
1) Become familiar with the manual and select

breakers suitable to machine specifications.
2) Make careful selection in consideration of oil
quantity, pressure and striking force, to enable
satisfied performance.
3) When apply a breaker to the machine,
consult your local dealer of Hyundai for further
explanation.
8-1
2. CIRCUIT CONFIGURATION
1) As for breaker oil pressure line, use extra spool of main control valve.
2) Set proper breaker pressure on load relief valve.
※ The initial setting pressure of load relief valve for breaker is 210 bar.
3) The pressure of the ROBEX330LC-9S system is 350 kgf/cm2 (4980 psi).
4) Adjusting oil quantity Oil quantity setting (type 1 cluster)

■ TYPE 1 CLUSTER
(1) Use the breaker mode from work tool of cluster.
Use select switch to control the oil flow quantity.
ÂSetting oil quantity (220 lpm)
Flow set
ÂMax flow : Set the maximum flow for the
attachment. 300H8HB01
ÂFlow level : Reduce the operating flow from
maximum flow.
- Breaker : Max 7 steps, reduced
10 lpm each step.
(2) If the quantity of hydraulic oil is not controlled
properly, it causes short lifecycle of the breaker
and the machine by increased breaking force
and count.
■ TYPE 2 CLUSTER
(1) Use accel dial switch to control the oil flow quantity.
5) The accumulator should be used to the breaker charging and return line.
If the accumulator is not used, it will be damage as the input wave is delivered.
ö Keep the pressure pulsation of pump below 60 kgf/cm2 (853 psi psi)) by installing the accumulator.
6) Do not connect the breaker return line to the main control valve, but connect to the return line front
of the cooler.
7) Do not connect the breaker return line to drain lines, such as of swing motor, travel motor or pump,
otherwise they should be damaged.
8) One of spool of the main control valve should be connected to the tank.
9) Select the size of pipe laying considering the back pressure.
10) Shimless tube should be used for the piping. The hose and seal should be used Hyundai genuine
parts.
11) Weld the bracket for pipe clamp to prevent damage caused by vibration.
8-2
3. MAINTENANCE
1) MAINTENANCE OF HYDRAULIC OIL AND

FILTER Service interval unit : hours
(1) As machine with an hydraulic breaker provides Operating Hydraulic Filter
Attachment
the hydraulic oil becomes severely contaminated. rate oil element
600★1
(2) So, unless frequently maintained, the machine Breaker 100 % 200
1000★2
may easily go out of order. ★1
: Conventional hydraulic oil
(3) Inspect and maintain hydraulic oil and 4 kinds of ★2
: Hyundai genuine long life hydraulic oil
filter elements in particular, in order to prolong
ú Replace following filter same time
machine life.
ÂHydraulic return filter : 1 EA
ÂPilot line filter : 1 EA
2) RELEASE THE PRESSURE IN BREAKER
ÂDrain filter cartridge : 1 EA
CIRCUIT
When breaker operating is finished, stop engine
and push pedal or switch for breaker to release Hyd oil change guide for hydraulic breaker
pressure in breaker circuit.
If pressure still remains, the lifetime of the 100
diaphragm in the accumulator will be shortened. Average 80
operating
3) Be careful to prevent contamination by dust, sand rate of 60 Time to change oil
machine
and etc. (%) 40
2
If such pollution become mixed into the oil, the 1
20
pump moving parts will wear abnormally, shorten 0
1000 2000 3000 4000 5000
lifetime and become damaged.
Operating hours of machine(Hr)
4) When operating breaker, bolts and nuts of main
equipment may be loosened by vibration. So, it
★1
must be inspected periodically. : Conventional hydraulic oil
★2
: Hyundai genuine long life hydraulic oil
8-3
4. PRECAUTIONS WHILE OPERATING THE BREAKER
1) DO NOT BREAK ROCK WHILE LOWERING Incorrect

As the breaker is heavy in comparison with
bucket, it must be operated slowly.
If breaker is rapidly pushed down, working device
may be damaged.
38098OA01
2) D O N O T U S E B R E A K E R T O C A R R Y Incorrect
BROKEN STONE OR ROCK BY SWING
OPERATING
This may damage the operation device and swing
system.
38098OA02
3) O P E R AT E B R E A K E R W I T H A G A P I N Incorrect
EXCESS OF 100 mm (4 inches) FROM THE
END OF THE STROKE TIP
If breaker is operated with the end tip, the cylinder
may be damaged.
38098OA03
4) I F T H E H Y D R AU L I C H O S E S V I B R AT E Incorrect
EXCESSIVELY
If the machine used in this condition continuously
this will effect badly on the machine such as
loosening bolt, oil leakage, damage of pump pipe
and etc.
38098OA04
8-4
5) DO NOT CONTINUE TO WORKING OVER Incorrect
ONE MINUTE AT SAME POSITION OF BOOM
For one
AND ARM minite
This will increase the temperature of the oil, and
cause problem in the accumulator and seals.
38098OA05
6) DO NOT MOVE MACHINE OR BREAKER Incorrect

WHILE STRIKING
Do not move hammer while striking.
This will cause damage to the working device and
the swing system.
2907A8OA06
7) DO NOT WORK WHILE SWING STATE

Prohibitation
Do not work while swing position of superstructure.
It cause the band of track shoe, oil leakage of
roller.
Work Work
Prohibitation
2907A8OA07
8) TA K E C A R E O F C H I S E L A N D B O O M Incorrect
INTERFACE
Make sure of the arm and bucket control lever
operation.
38098OA06
8-5
5. QUICK CLAMP
1) FIXING BUCKET WITH QUICK CLAMP

(1) Before fixing bucket, remove safety pin of Quick clamp switch
the moving hook.
Safety button
(2) Pulling safety button, press the quick
clamp switch to unlock position. Then, the
moving hook is placed on release
position.
Safety pin
QUICK-1
(3) Aligning the arm and bucket, insert static

hook of quick clamp to the bucket pin.
Static hook
QUICK-2
(4) Operate RCV lever to bucket-in position.

Then, the moving hook is coupled with
the bucket link pin.
Moving hook
Make sure that the moving hook is
completely contacted with bucket link pin.
QUICK-3
(5) Push safety button to lock position.

RCV(RH)
Operate RCV lever to bucket-in position.
Safety button
öBe sure to check connection status
between bucket pins and hooks of
quick clamp.
Front
QUICK-4
8-6
(6) After checking the connection status
between bucket pins and hooks of quick
clamp, insert safety pin of moving hook
to lock position.
Safety pin
QUICK-5
2) REMOVE BUCKET FROM QUICK CLAMP

Removing procedure is reverse of fixing.
3) PRECAUTION OF USING QUICK CLAMP
When operating the machine with quick
clamp, confirm that the quick clamp
switch is lock position and safety pin of LOCK UNLOCK
moving hook is inserted.
Operating the machine with quick
clamp switch unlocked and without
safety pin of moving hook can cause
the bucket to drop off and bring about
the accident.
Serious injury or death can result from 21098QC06
this accident.
Be careful to operate the machine
equipped with quick clamp. The bucket
may hit cab, boom and boom cylinders
when it reaches vicinity of them.
HYUNDAI will not be responsible for
any injur y or damage in case that
safety pin is not installed properly.
QUICK-7
8-7

R300LC 9S

Uploaded by

Copyright:

Available Formats

R300LC 9S

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

R300LC 9S

Uploaded by

Copyright:

Available Formats

SAFETY HINTS

1. BEFORE OPERATING THE MACHINE

Be sure to understand thoroughly all about the

Fully understand the details and process of the

Do not operate when tired, or after drinking

Check for leakage of engine oil, hydraulic oil,

Do not operate the machine if it requires repairs.

Be prepared if a fire starts.

Any modification made without authorization

PREPARE FOR EMERGENCY

Only in case of emergency, use the installed

PRECAUTIONS FOR ATTACHMENTS

MACHINE CONTROL PATTERN

Battery posts, terminals and related accesso-

Do not load the machine with the lifting eyes on

Use the handle and footstep when getting on or

Sound the horn to warn nearby personnel

Operate carefully to make sure all personnel or

When using the work equipment, pay attention

Check the locations of underground gas

The operating near the electrical lines is very

6.6 kV 3m (10 ft)

If the machine touches the electric power lines,

When using the machine as breaker or

Avoid operating on a cliff or soft ground as there

Operate for the lifting work considering the

Operate the machine after making ground flat

The swing on the slope can be danger of

Avoid parking and stopping on a slope.

Traveling on a slope is dangerous.

Steering of the machine while traveling on a

The engine angularity limits are 35 degree.

Slow down when traveling through obstacles or

When working on soft ground, place mats or

When operating in water or when crossing shal-

KEEP RIDERS OFF MACHINE

Stop the engine immediately when the trouble

Park on a flat place and stop the engine for

Do not remove the radiator cap from hot engine.

Do not work below the machine.

Do not touch exhaust pipe, or may cause

Do not open the engine hood and covers while

Be careful of not hitting the edges when you

The antislip protection should be replaced if

Be careful of not touching slip, fall down etc.,

HIGH PRESSURE GAS

LIFT EYES CAN FAIL

When leaving the machine after parking,

Park the machine in the flat and safe place.

Hope you can work easily and safely

Battery box Fuel tank Hydraulic tank Main pump

Arm Arm cylinder Boom Boom cylinder Cab Muffler Counterweight

Bucket cylinder Connecting link Idler Carrier roller Sprocket

Side cutter Connecting rod Track roller Track Travel motor

Description Unit Specification

Description Unit Specification

Description Unit Specification

6.45 m (21' 2") Boom 6.15 m (20' 2") Boom

6.45 m (21' 2") Boom 6.15 m (20' 2") Boom